Philips TV VCR Combo CCX133AT User Manual

TV/VCR Com bination  
TM  
CCX133AT  
O wners Manual  
I M P O R T A N T !  
Return Your W arranty Registration Card  
W ithin 10 Days. See W hy Inside.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Introduction 3  
W elcom e to your TV/VCR owners m anual.  
This manual has six sections: Setting Up Your TV/VCR; Description of Controls; Basic Operations; Recording  
Options; Playing Options; and Information You May Need. The instructions explain all of the TV/VCR’s fea-  
tures, which are listed below. You cannot hurt your TV/VCR by trying the features! So read on – and relax.  
Features  
• HQ (High Quality) System  
• Automatic Channel Programming  
On-Screen Displays in English or Spanish  
• Automatic Tracking Adjustment  
One Touch Recording  
• Unattended (Timer) Recording  
Special Effects Playback: Forward and Reverse Searching; Still  
• Remote Control  
• Automatic Operation Features  
• Closed Caption System  
• Automatic Clock Setting  
• Daylight-Saving Time  
VCR Plus+ Programming System  
Smart Sound  
Safety Precautions  
W arning: To prevent fire or shock hazard, do not expose  
this equipm ent to rain or m oisture.  
FCC W arning: Any unauthorized changes or m odifica-  
tions to this equipm ent void the users authority to oper-  
ate it.  
This TV/VCR, equipped with a HQ (High Quality) system, is com-  
patible with existing VHS (video home system) equipment.  
Philips Consum er Electronics Com pany recommends that  
you use only video cassette tapes that have been tested and  
inspected for use in two, four, six, and eight hour VCRs, and  
which are labeled with the  
mark. The use of tapes that  
have not been inspected for use in two, four, six, and eight hour  
VCRs may result in poor picture quality and excessive deposits on  
the video heads, which may not be covered by the warranty if  
damage occurs.  
Note to the Cable TV System Installer: This reminder is  
provided to call the Cable TV system installers attention to  
Article 820-40 of the National Electrical Code, which provides  
guidelines for proper grounding – in particular, specifying that the  
cable ground shall be connected to the grounding system of the  
building, as close to the point of cable entry as possible.  
Helpful Hint  
Copyright 1997 Philips Consumer Electronics Company. All rights  
reserved. VCR Plus+ and PlusCode are trademarks of Gemstar  
Development Corporation. The VCR Plus+ system is manufac-  
tured under license from Gemstar Development Corporation.  
Before doing anything else, record  
the TV/VCR’s model and serial num-  
bers in the spaces provided on page  
two. These numbers will help us  
assist you if you ever call for help.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4 Table of Contents  
Setting Up Your TV/VCR  
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3  
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4  
Before Using the TV/VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5  
Hooking Up the TV/VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 - 7  
Turning On the TV/VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8  
Language Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9  
Channel Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 - 11  
Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 - 17  
Daylight-Saving Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18  
Time Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19  
Description of Controls  
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20  
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21  
Remote Control Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 - 23  
Adjusting the Picture Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 - 25  
On-Screen Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26  
Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27  
Basic O perations  
Playing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28  
Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29  
Recording O ptions  
One Touch Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30  
Rerecording (Tape Duplication) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31  
Timer Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 - 35  
Setting Up the VCR Plus+ Programming System . . . . . . . . . . . . . . . . . . . . . . . . . .36 - 37  
Timer Recording With the VCR Plus+ Programming System . . . . . . . . . . . . . . . . .38 - 39  
Record Defeat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40  
Playing O ptions  
Setting the Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41  
Closed Captioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 - 43  
Volume Bar / Smart Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44  
Repeat Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45  
A - B Repeat Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 - 47  
Real Time Counter Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48  
Automatic Operation Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49  
Playback Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50  
Inform ation You May Need  
Specifications / Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51  
Helpful Hints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 - 53  
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54  
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55  
Supplied Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before Using the TV/VCR 5  
Putting Batteries in the Rem ote Control  
1
Rem ove the battery com partm ent lid on the bottom of  
the rem ote control by sliding it in the direction of the  
arrow.  
1
2
3
2
Place two AA batteries inside the battery com partm ent  
with their polarities ( and ends) aligned as indicated.  
+
3
Replace the battery com partm ent lid.  
Rem oving the Shipping Card  
A shipping card may be inserted in the cassette compartment of  
the TV/VCR. Before you insert a cassette tape, you must  
remove the shipping card. To remove the card, open the cas-  
sette compartment, then grasp the tape and remove the card.  
Erase Protection  
Video cassette tapes have record tabs to ensure that recordings  
are not accidentally erased.  
1
2
1
To prevent accidental erasure, break off the tab with a  
screwdriver.  
2
To record again, cover the hole with cellophane tape.  
Using the Rem ote Control  
Point the remote control at the TV/VCR’s remote sensor.  
Do not put objects between the remote control and the  
TV/VCR.  
VCR Maintenance  
In this TV/VCR, use only tapes with the  
mark.  
Make sure any light adhesive stick-on notes are removed from  
the video cassette tape before putting the tape in the TV/VCR.  
Removable labels like these can jam the TV/VCR.  
Periodic maintenance is required to maintain your TV/VCR’s  
continued excellent performance. This TV/VCR has an automatic  
head cleaning system. However, the video heads will eventually  
require cleaning or replacement. Cleaning or replacement of the  
video heads should be performed by an authorized service cen-  
ter.  
Helpful Hints  
The remote control and its batteries  
are supplied.  
• Do not mix alkaline and man-  
ganese batteries.  
• Do not mix old and new batteries.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6 Hooking Up The TV/VCR  
1
Hook up your TV/VCR using one of the connections shown.  
Connect a Cable signal  
or an antenna to the  
ANT(enna) Jack.  
A.  
Hooking Up Your TV/VCR  
W ith a Cable Signal or  
O utdoor Antenna  
ANT.  
ANT.  
Connect the Cable signal to  
the IN Jack on the Cable Box.  
B.  
Hooking Up Your TV/VCR  
W ith a Cable Box  
Connect an RF coaxial cable (75-  
To view any channel, set the  
TV/VCR to the Cable Box output  
channel (channel 03 or 04). Then,  
select channels at the Cable Box.  
ohm, not supplied) to the OUT Jack  
on the Cable Box and to the  
ANT(enna) Jack on the TV/VCR.  
IN  
OUT  
ANT.  
ANT.  
Rod Antenna  
(not supplied)  
C.  
Hooking Up Your TV/VCR  
W ith an Indoor Antenna  
To install a rod antenna (not sup-  
plied), push the stem of the antenna  
into the antenna hole on the top of  
the TV/VCR. Connect the antenna  
wire to the ANT(enna) Jack on the  
back of the TV/VCR as shown.  
Extend the antenna and adjust its  
length, direction, and angle for the  
clearest picture.  
ANT.  
ANT.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Hooking Up The TV/VCR (contd) 7  
D.  
Hooking Up Your  
TV/VCR to Another  
Video Source  
(VCR or Cam corder)  
You may need this connection  
if you want to copy tapes.  
Details are on page 31.  
Use an Audio cable to connect the AUDIO  
OUT Jack on the VCR to the AUDIO Jack  
on the front of the TV/VCR.  
AUDIO/VIDEO OUT  
Jacks on VCR  
3CH  
IN  
4CH  
AUDIO VIDEO  
ANT.  
OUT  
OUT  
IN  
AUDIO VIDEO  
POWER  
STOP REW  
EJECT  
PLAY F.FWD REC/OTR  
VOLUME  
CHANNEL EARPHONE  
AUDIO VIDEO  
REC  
3CH  
IN  
4CH  
AUDIO VIDEO  
ANT.  
OUT  
OUT  
IN  
AUDIO/VIDEO Jacks  
on front of TV/VCR  
Use a Video cable to connect the VIDEO OUT Jack on  
the VCR to the VIDEO Jack on the front of the TV/VCR.  
2
Plug in the TV/VCR.  
3
Before you turn on the TV/VCR, go to page eight.  
Helpful Hints  
Before connecting the rod antenna (or mixing adapter or coaxial cable) to the ANT(enna) Jack, make sure the  
pin is not bent. If the pin is bent, straighten it as illustrated, then connect it to the ANT(enna) Jack.  
A rod antenna (not supplied) is available from Philips Service Company. The part number is 4835 3033 7006.  
To order, call 1-800-851-8885.  
Audio and video cables are not supplied.  
Bent pin  
Crooked Pin  
Straight Pin  
Plug  
Cable  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8 Turning On the TV/VCR  
Before you turn on the TV/VCR, make sure there are batteries in  
the remote control (details are on page five) and the TV/VCR is  
hooked up correctly (details are on pages six - seven).  
The instructions on this page work only when you turn on the  
TV/VCR for the first time.  
1
2
2
5
8
0
3
6
1
4
7
o
1
9
p
o
Press the PO W ER button. The TV/VCR will come on and the  
language select display screen shown below will appear.  
+100  
p
SELECT LANGUAGE  
o
1 ENGLISH  
ON  
PLAY  
+
REW  
F.FWD  
2 ESPAÑOL  
STOP  
4
MAKE SELECTION OR  
PRESS EXIT TO CONTINUE  
p
2
3
Press the Num ber 1 button to select English on-screen  
displays or press the Num ber 2 button to select Spanish  
on-screen displays.  
3
Press the STATUS/EXIT button. The channel program dis-  
play screen shown below will appear.  
Helpful Hints  
CONNECT ANTENNA OR CABLE  
TO TVCR  
If you do not see any on-screen dis-  
plays when you turn on the TV/VCR,  
check your hook-ups, then try again.  
If you still do not see any on-screen  
displays, follow the steps on pages  
nine - 11 to select a language and  
program channels.  
THEN PRESS+  
TO END PRESS EXIT  
4
To skip this feature and play a tape  
immediately, insert a tape with its  
record tab removed. Playback will  
begin. Or, to skip step 2, press the  
STATUS/EXIT button before pro-  
ceeding. All on-screen displays will  
be in English. To skip step 4, press  
the STATUS/EXIT button before  
proceeding. Channels will not be  
programmed, and CHANNELS NOT  
SET will appear on-screen briefly.  
You cannot program channels if you  
are using a Cable Box.  
Line Input mode will always be  
stored in the TV/VCR’s memory as  
channel 00. When you select chan-  
nel 00, A/V IN will appear on-  
screen briefly. Press the CHANNEL  
Up/Down buttons or Number but-  
tons to select another channel.  
Press the F.FW D/+ button to begin autom atic channel  
program m ing. The TV/VCR will place all of the channels you  
receive into its memory, so when you scan through channels using  
the CHANNEL Up/Down buttons, youll only scan through chan-  
nels that you receive. When channels are programmed, CHAN-  
NELS ARE SET will appear on-screen briefly. Then the TV/VCR  
will go to the lowest channel programmed.  
(If you try to program channels when there is no antenna or cable  
connected to the TV/VCR, programming will appear to take place,  
but eventually a NO TV SIGNALS ... message will appear on-  
screen. Connect an antenna or cable to the TV/VCR, then try  
again. You may need to follow the steps on pages nine - 11  
instead.)  
5
Now, you may use the CHANNEL Up/Down buttons or the  
Number buttons on the remote control to select a TV/VCR chan-  
nel. Use the VOLUME Up/Down buttons to adjust the sound.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Language Selection 9  
Follow the steps below to change the language of the on-screen  
displays.  
1
Press the MENU button to display the pop up m enu.  
PRESS +  
B PRIM. SETUP  
VCR PROGRAM  
VCR SETUP  
CAPTION  
REMINDER  
BRIGHTNESS  
2
5
8
0
3
6
1
4
7
3
o
4
2
9
p
o
2
+100  
Press the PLAY/button or the STO P/button to select  
PRIM. SETUP. (If the menu is in Spanish, select PREPARA-  
CION.) Then, press the F.FW D/+ button.  
p
o
PLAY  
+
REW  
F.FWD  
PRIMARY SETUP  
STOP  
1 SELECT LANGUAGE  
p
2 AUTO PROGRAMMING  
3 ADD/DELETE CHANNEL  
4 CH. MEMORY REVIEW  
5 VOLUME BAR  
6 SET CLOCK  
[ON]  
TO SELECT PRESS NUMBER  
TO END PRESS EXIT  
1
5
3
Press the Num ber 1 button to choose SELECT LAN-  
GUAGE. (If the menu is in Spanish, press the Number 1 button  
to select SELECCION IDIOMA.)  
SELECT LANGUAGE  
1 ENGLISH  
ON  
2 ESPAÑOL  
MAKE SELECTION OR  
PRESS EXIT TO CONTINUE  
4
Press the Num ber 1 button if you want the on-screen dis-  
plays in English. ON will appear to the right of ENGLISH on-  
screen. O r, press the Num ber 2 button if you want the on-  
screen displays in Spanish. SI will appear to the right of  
ESPAÑOL on-screen.  
5
Press the STATUS/EXIT button.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10 Channel Memory  
Although the TV/VCR may automatically memorize the channels  
you receive when you turn it on for the first time, you may pro-  
gram channels again. Follow the steps below to program channels.  
Wait for the TV/VCR to pro-  
gram channels.  
5
1
Press the MENU button to display the pop up m enu.  
TO ADJUST PRESS +/-  
CABLE  
B INPUT  
EXIT  
2
5
8
0
3
6
1
4
7
4
3
PRIM. SETUP  
VCR PROGRAM  
VCR SETUP  
CAPTION  
o
9
p
o
+100  
p
2
o
Press the PLAY/button or the STO P/button to select  
INPUT. Press the REW (ind)/– button or the F.FW D/+  
button until ANTENNA or CABLE (whichever you have)  
appears to the right of the pop up m enu.  
PLAY  
+
REW  
F.FWD  
2
1
STOP  
p
3
Press the STO P/button repeatedly to select PRIM.  
SETUP, then press the F.FW D/+ button.  
PRIMARY SETUP  
1 SELECT LANGUAGE  
2 AUTO PROGRAMMING  
3 ADD/DELETE CHANNEL  
4 CH. MEMORY REVIEW  
5 VOLUME BAR  
6 SET CLOCK  
[ON]  
TO SELECT PRESS NUMBER  
TO END PRESS EXIT  
4
Press the Num ber 2 button to select AUTO PRO GRAM-  
MING. AUTO PROGRAMMING MEMORIZED CH. ... will  
appear on-screen. The TV/VCR will place all of the channels you  
can receive into its memory.  
5
W ait for a few m inutes. When programming is complete,  
CHANNELS ARE SET will appear on-screen. Then the program-  
ming of the lowest channel number placed in the TV/VCR’s mem-  
ory will appear on-screen. Now, when you press the CHANNEL  
Up/Down buttons, you will scan only through channels you  
receive.  
Helpful Hints  
Line Input mode will always be  
stored in the TV/VCR’s memory as  
channel 00. You cannot delete it.  
You cannot program channels when  
the TV/VCR is on channel 00 (A/V  
IN will be selected at INPUT at step  
2). Select ANTENNA or CABLE at  
step 2.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Channel Memory (contd) 11  
Adding/Deleting Channels  
1
Press the MENU button to display the pop up m enu.  
TO ADJUST PRESS +/-  
CABLE  
B INPUT  
3
EXIT  
PRIM. SETUP  
VCR PROGRAM  
VCR SETUP  
CAPTION  
2
5
8
0
3
6
1
4
7
5
4
o
9
p
o
2
Press the PLAY/button or the STO P/button to select  
PRIM. SETUP, then press the F.FW D/+ button.  
+100  
p
o
PRIMARY SETUP  
PLAY  
2
1
1 SELECT LANGUAGE  
+
REW  
F.FWD  
2 AUTO PROGRAMMING  
3 ADD/DELETE CHANNEL  
4 CH. MEMORY REVIEW  
STOP  
p
5 VOLUME BAR  
6 SET CLOCK  
[ON]  
TO SELECT PRESS NUMBER  
TO END PRESS EXIT  
6
3
Press the Num ber 3 button to select ADD/DELETE  
CHANNEL.  
SELECT CHANNEL NUMBER  
CH – –  
TO END PRESS EXIT  
Helpful Hint  
To review the channels memorized  
by the TV/VCR, follow these steps.  
1) Press the MENU button.  
2) Press the PLAY/button or the  
STOP/button to select PRIM.  
SETUP. Press the F.FWD/+ button.  
3) Press the Number 4 button to  
select CH. MEMORY REVIEW. A  
list of programmed channels will  
appear on-screen.  
4
Enter the channel num ber you want to add or delete.  
CH 12  
1 ADD  
2 DELETE  
3 SELECT ANOTHER CH  
TO SELECT PRESS NUMBER  
TO END PRESS EXIT  
4) If all the programmed channels  
dont fit on-screen, press the  
5
W ithin five seconds, press the Num ber 1 button to add  
that channel or the Num ber 2 button to delete that chan-  
nel. If you do not make a choice within five seconds, you will  
return to the previous screen. (If you make a mistake, press the  
Number 3 button to select another channel.)  
Number 1 button. If you do not  
press the Number 1 button within  
10 seconds, the remaining channels  
will appear on-screen. (If there are  
no remaining channels, the previous  
menu will appear.) Or press the  
Number 2 button to see the previ-  
ous screen of channels.  
6
Press the STATUS/EXIT button.  
5) Press the STATUS/EXIT button.  
Programming of the channel you added or deleted will appear.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12 Setting the Clock  
There are three ways to set the clock: Manually, with Automatic  
PBS Channel Selection, or with Manual PBS Channel Selection.  
With m anual clock setting, you tell the TV/VCR the current  
time. The TV/VCR then adjusts the time accordingly. With  
Automatic or Manual PBS Channel Selection, the TV/VCR gets the  
current time from your local PBS station. It updates the time by  
referring to your PBS station broadcasts. If you use either Manual  
PBS Channel Selection or Automatic PBS Channel Selection, fol-  
low the steps on page 19 to have the TV/VCR update the clock  
according to your Time Zone.  
To set the clock manually, follow the steps on pages 12 -13. To  
set the clock using Automatic PBS Channel Selection, follow the  
steps on pages 14 - 15. To set the clock using Manual PBS  
Channel Selection, follow the steps on pages 16 - 17.  
Before you begin, make sure:  
2
5
8
0
3
6
1
4
7
o
3
9
p
o
+100  
p
The TV/VCR is hooked up and turned on. Details are on pages  
six - eight.  
Channels are programmed. Details are on pages 10 - 11.  
You make each entry within 60 seconds of the previous entry.  
(If you do not, you may start again at step 1.)  
o
PLAY  
2
1
+
REW  
F.FWD  
STOP  
p
Manual Clock Setting  
1
Press the MENU button to display the pop up m enu.  
B PRIM. SETUP  
VCR PROGRAM  
VCR SETUP  
PRESS +  
CAPTION  
REMINDER  
BRIGHTNESS  
2
Press the PLAY/button or the STO P/button to select  
PRIM. SETUP. Then, press the F.FW D/+ button.  
Helpful Hints  
PRIMARY SETUP  
Entries that do not match the  
TV/VCR’s internal calendar will  
cause a question mark (?) to  
appear on the TV/VCR screen.  
1 SELECT LANGUAGE  
2 AUTO PROGRAMMING  
3 ADD/DELETE CHANNEL  
4 CH. MEMORY REVIEW  
5 VOLUME BAR  
6 SET CLOCK  
[ON]  
TO SELECT PRESS NUMBER  
TO END PRESS EXIT  
To make corrections while you are  
setting the clock, press the CLEAR  
button until the space for the num-  
ber you want to correct is flashing.  
Then enter the correct number.  
To make corrections after you have  
set the clock, start again at step 1.  
If you press the STATUS/EXIT but-  
ton when you are setting the clock,  
the TV/VCR will exit Set Clock mode  
and return to the program you were  
watching.  
3
Press the Num ber 6 button to select SET CLO CK.  
SET CLOCK  
1 AUTO CLOCK  
[ON]  
2 SET MANUAL CLOCK  
3 DAYLIGHT SVG.TIME [ON]  
4 SET TIME ZONE  
[AUTO]  
TO CONTINUE PRESS MENU  
TO SELECT PRESS NUMBER  
TO END PRESS EXIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the Clock (contd) 13  
4
Press the Num ber 2 button to select SET MANUAL  
CLO CK.  
SET MANUAL CLOCK  
4
TIME – – : – –  
DATE – – / – – / – –  
TO END PRESS EXIT  
2
5
8
0
3
6
1
4
7
5
6
o
9
p
o
5
+100  
Press two Num ber buttons for the hour(s) and two  
Num ber buttons for the m inute(s). Then press 1 for AM  
or 2 for PM. For example, for 9:30 PM, press 09, 30, 2.  
p
o
PLAY  
+
REW  
F.FWD  
SET MANUAL CLOCK  
STOP  
TIME  
09 : 30 PM  
p
MONTH  
– – / – – / – –  
TO CORRECT PRESS CLEAR  
TO END PRESS EXIT  
7
6
Press two Num ber buttons for the m onth, two Num ber  
buttons for the day, and two Num ber buttons for the  
year. For example, for July 1, 1997, press 07, 01, 97. The day of  
the week will appear automatically.  
SET MANUAL CLOCK  
TIME  
09 : 30 PM  
DATE  
07 / 01 / 97  
TUESDAY  
TO CORRECT PRESS CLEAR  
TO END PRESS EXIT  
7
Press the STATUS/EXIT button to start the clock. The  
screen will return to the program you were watching.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14 Setting the Clock (contd)  
Autom atic PBS Channel Selection  
1
Press the MENU button to display the pop up menu.  
B PRIM. SETUP  
VCR PROGRAM  
VCR SETUP  
PRESS +  
CAPTION  
REMINDER  
BRIGHTNESS  
2
5
8
0
3
6
4
1
4
7
o
3
9
p
o
2
+100  
Press the PLAY/button or the STO P/button to select  
PRIM. SETUP. Then, press the F.FW D/+ button.  
p
o
PRIMARY SETUP  
PLAY  
1 SELECT LANGUAGE  
+
REW  
F.FWD  
2 AUTO PROGRAMMING  
3 ADD/DELETE CHANNEL  
4 CH. MEMORY REVIEW  
STOP  
p
5 VOLUME BAR  
6 SET CLOCK  
TO SELECT PRESS NUMBER  
TO END PRESS EXIT  
[ON]  
2
1
3
Press the Num ber 6 button to select SET CLO CK.  
SET CLOCK  
1 AUTO CLOCK  
[ON]  
2 SET MANUAL CLOCK  
3 DAYLIGHT SVG.TIME [ON]  
4 SET TIME ZONE  
[AUTO]  
TO CONTINUE PRESS MENU  
TO SELECT PRESS NUMBER  
TO END PRESS EXIT  
4
If O N appears beside AUTO CLO CK, press the MENU  
button. If O FF appears beside AUTO CLO CK, press the  
Num ber 1 button so that O N appears to the right of  
AUTO CLO CK, then press the MENU button.  
AUTO CLOCK  
AUTO CLOCK USES  
PBS CHANNEL DATA  
1
2
SET PBS CH. AUTO  
SET PBS CH. MANUAL  
TO SELECT PRESS NUMBER  
TO END PRESS EXIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the Clock (contd) 15  
Wait for the TV/VCR to find  
the time.  
5
Press the Num ber 1 button to select SET PBS CH.  
AUTO .  
6
SET AUTO CLOCK  
TIME  
– – : – –  
DATE  
– – / – – / – –  
NOW SEARCHING  
TO END PRESS EXIT  
2
5
8
0
3
6
1
4
7
5
7
o
6
9
p
o
NOW SEARCHING flashes on the TV/VCR screen.  
+100  
However, you may see the message “PLEASE TURN OFF TO SET  
AUTO CLOCK PLEASE WAIT SEVERAL MINUTES.” If this mes-  
sage appears, turn off the TV/VCR for a few minutes. When you  
turn on the TV/VCR, the time will be set.  
p
o
PLAY  
+
REW  
F.FWD  
STOP  
If the time is not set, repeat steps 1 - 5. Or, follow the steps on  
pages 12 - 13 to set the clock manually or pages 16- 17 to set the  
clock with Manual PBS Channel Selection.  
p
7
W hen the TV/VCR finds the PBS channel, the tim e will  
appear on-screen. Press the STATUS/EXIT button.  
SET AUTO CLOCK  
TIME  
06 : 30 PM  
DATE  
07 / 01 / 97  
TUESDAY  
TO END PRESS EXIT  
Helpful Hints  
If CANNO T FIND CLO CK DATA flashes on the  
TV/VCR screen, you will be prom pted to turn off the  
TV/VCR. Turn off the TV/VCR. Leave it off for several min-  
utes. When you turn on the TV/VCR again, the clock will be  
set.  
To display the time, press the STA-  
TUS/EXIT button. A status display,  
which includes the time, will appear  
on the TV/VCR screen. Details are  
on page 26.  
SET AUTO CLOCK  
If you press the STATUS/EXIT but-  
ton while you are setting the clock,  
the screen will exit Set Clock mode  
and return to the program you were  
watching. If this happens, start over.  
You must turn off the TV/VCR for  
several minutes during automatic  
clock setting. If the clock is not set  
when you turn on the TV/VCR,  
TIME  
– – : – –  
DATE  
– – / – – / – –  
CANNOT FIND CLOCK DATA  
TO END PRESS EXIT  
repeat the steps for Automatic PBS  
Channel Selection. If the clock still is  
not set, set the clock manually.  
You cannot use the AUTO CLOCK  
feature if you don’t receive a PBS  
channel that carries a time signal in  
your area. Set the clock manually.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
16 Setting the Clock (contd)  
Manual PBS Channel Selection  
1
Press the MENU button to display the pop up m enu.  
B PRIM. SETUP  
VCR PROGRAM  
VCR SETUP  
PRESS +  
CAPTION  
REMINDER  
BRIGHTNESS  
2
5
8
0
3
6
1
4
7
o
9
p
o
3
2
4
+100  
Press the PLAY/button or the STO P/button to select  
PRIM. SETUP. Then, press the F.FW D/+ button.  
p
o
PRIMARY SETUP  
PLAY  
1 SELECT LANGUAGE  
+
REW  
F.FWD  
2 AUTO PROGRAMMING  
3 ADD/DELETE CHANNEL  
4 CH. MEMORY REVIEW  
STOP  
p
5 VOLUME BAR  
6 SET CLOCK  
TO SELECT PRESS NUMBER  
TO END PRESS EXIT  
[ON]  
2
1
3
Press the Num ber 6 button to select SET CLO CK.  
SET CLOCK  
1 AUTO CLOCK  
[ON]  
2 SET MANUAL CLOCK  
3 DAYLIGHT SVG.TIME [ON]  
4 SET TIME ZONE  
[AUTO]  
TO CONTINUE PRESS MENU  
TO SELECT PRESS NUMBER  
TO END PRESS EXIT  
4
If O N appears beside AUTO CLO CK, press the MENU  
button. If O FF appears beside AUTO CLO CK, press the  
Num ber 1 button so that O N appears to the right of  
AUTO CLO CK, then press the MENU button.  
AUTO CLOCK  
AUTO CLOCK USES  
PBS CHANNEL DATA  
1
2
SET PBS CH. AUTO  
SET PBS CH. MANUAL  
TO SELECT PRESS NUMBER  
TO END PRESS EXIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the Clock (contd) 17  
5
Wait for the TV/VCR to  
find the time.  
Press the Num ber 2 button to select SET PBS CH. MAN-  
UAL.  
7
AUTO CLOCK (PBS) CH – –  
TIME  
– – : – –  
DATE  
– – / – – / – –  
SELECT CHANNEL NUMBER  
TO END PRESS EXIT  
2
5
8
0
3
6
1
4
7
5
6
o
6
9
p
o
Use the Num ber buttons to select your PBS station.  
+100  
AUTO CLOCK (PBS) CH 12  
p
o
TIME  
– – : – –  
PLAY  
DATE  
– – / – – / – –  
+
REW  
F.FWD  
STOP  
NOW SEARCHING  
TO END PRESS EXIT  
p
7
8
NOW SEARCHING flashes on the TV/VCR screen.  
8
W hen the TV/VCR finds the PBS channel, the tim e will  
appear on-screen. Press the STATUS/EXIT button.  
AUTO CLOCK (PBS) CH 12  
TIME  
06 : 30 PM  
DATE  
07 / 01 / 97  
TUESDAY  
TO END PRESS EXIT  
If CANNO T FIND CLO CK DATA flashes on the  
TV/VCR screen and you know another PBS channel,  
press the Num ber 1 button to select SELECT NEW  
PBS CH. Repeat step 6.  
If CANNO T FIND CLO CK DATA flashes on the  
TV/VCR screen and you do not know another channel,  
press the Num ber 2 button to select SET PBS CH.  
AUTO . The TV/VCR will search for the PBS channel automati-  
cally.  
• If the PBS channel is found, the time will appear on-screen.  
• If the PBS channel is not found, you will be prompted to turn  
off the TV/VCR. Leave it off for several minutes.  
When you turn on the TV/VCR again, the time will be set.  
Helpful Hints  
To make corrections while you are  
setting the PBS station, press the  
CLEAR button, then enter the cor-  
rect number.  
If you have an Antenna hookup, you  
may select channels 2 - 69 at step  
6. If you have a cable connection,  
you may select channels 1 - 125 at  
step 6. Details about available  
channels are on pages 10 - 11.  
To display the time, press the STA-  
TUS/EXIT button. A status display,  
which includes the time, will appear  
on the TV/VCR screen. Details are  
on page 26.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
18 Daylight-Saving Time  
When the Daylight-Saving Time feature is ON, the TV/VCR clock  
will automatically move forward one hour on the first Sunday in  
April and move back one hour on the last Sunday in October.  
Details are on page 53.  
To turn Daylight-Saving Time ON or OFF, follow the steps below.  
4
1
Press the MENU button to display the pop up m enu.  
2
3
1
4
7
PRESS +  
B PRIM. SETUP  
VCR PROGRAM  
VCR SETUP  
5
8
0
6
o
3
5
CAPTION  
9
p
o
REMINDER  
BRIGHTNESS  
+100  
p
o
PLAY  
2
+
REW  
F.FWD  
Press the PLAY/button or the STO P/button to select  
PRIM. SETUP. Then, press the F.FW D/+ button.  
STOP  
p
2
PRIMARY SETUP  
1 SELECT LANGUAGE  
2 AUTO PROGRAMMING  
3 ADD/DELETE CHANNEL  
4 CH. MEMORY REVIEW  
1
5 VOLUME BAR  
6 SET CLOCK  
TO SELECT PRESS NUMBER  
TO END PRESS EXIT  
[ON]  
3
Press the Num ber 6 button to select SET CLO CK.  
SET CLOCK  
1 AUTO CLOCK  
[ON]  
2 SET MANUAL CLOCK  
3 DAYLIGHT SVG.TIME [ON]  
4 SET TIME ZONE  
[AUTO]  
TO CONTINUE PRESS MENU  
TO SELECT PRESS NUMBER  
TO END PRESS EXIT  
4
Press the Num ber 3 button so that O N or O FF appears  
beside DAYLIGHT SVG. TIME (Daylight-Saving Tim e).  
5
Press the STATUS/EXIT button.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Time Zone 19  
When you set the clock using AUTO CLOCK (either Manual PBS  
Channel Selection or Automatic PBS Channel Selection), you can  
specify a time zone in which a local PBS channel is located. That  
way, the TV/VCR will set the clock according to your time zone.  
1
Press the MENU button to display the pop up m enu.  
4
5
2
5
8
0
3
6
1
4
7
PRESS +  
B PRIM. SETUP  
VCR PROGRAM  
VCR SETUP  
o
3
6
CAPTION  
REMINDER  
BRIGHTNESS  
9
p
o
+100  
p
o
2
PLAY  
Press the PLAY/button or the STO P/button to select  
PRIM. SETUP. Then, press the F.FW D/+ button.  
+
REW  
F.FWD  
STOP  
p
2
1
PRIMARY SETUP  
1 SELECT LANGUAGE  
2 AUTO PROGRAMMING  
3 ADD/DELETE CHANNEL  
4 CH. MEMORY REVIEW  
5 VOLUME BAR  
6 SET CLOCK  
[ON]  
TO SELECT PRESS NUMBER  
TO END PRESS EXIT  
3
Press the Num ber 6 button to select SET CLO CK.  
SET CLOCK  
1 AUTO CLOCK  
[ON]  
2 SET MANUAL CLOCK  
3 DAYLIGHT SVG.TIME [ON]  
4 SET TIME ZONE  
[AUTO]  
TO CONTINUE PRESS MENU  
TO SELECT PRESS NUMBER  
TO END PRESS EXIT  
4
Press the Num ber 4 button to select SET TIME ZO NE.  
SET TIME ZONE  
1 AUTO  
[ON]  
2 ATLANTIC  
3 EASTERN  
4 CENTRAL  
5 MOUNTAIN  
6 PACIFIC  
7 ALASKA  
8 HAWAII  
TO SELECT PRESS NUMBER  
TO CONTINUE PRESS EXIT  
Helpful Hints  
If you select AUTO at step 5, the  
TV/VCR will set the clock according  
to the first PBS station it finds.  
You cannot select TIME ZONE at  
step 4 if AUTO CLOCK is set to  
OFF.  
5
Find your tim e zone, then press the Num ber button to  
select it. ON will appear beside the selected time zone.  
6
Press the STATUS/EXIT button twice.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
20 Front Panel  
Cassette Com partm ent  
Insert a video cassette tape here.  
Rem ote Sensor  
Receives an infrared signal from your remote  
control so you can operate the TV/VCR from  
a distance.  
REC(ord) Light  
Appears when a recording, timer recording,  
or one touch recording is in progress.  
It flashes when the TV/VCR power is turned  
off to set a timer recording, or when a  
recording is paused.  
VIDEO Jack  
Connect this jack to the video out jack of a  
camcorder or a VCR. Details are on page 31.  
AUDIO Jack  
Connect this jack to the audio out jack of a  
camcorder or a VCR. Details are on page 31.  
POWER  
STOP REW  
EJECT  
PLAY F.FWD REC/OTR  
VOLUME  
CHANNEL EARPHONE  
AUDIO VIDEO  
REC  
PO W ER Button  
Press to turn the power on or off.  
CHANNEL Up/Down  
Buttons  
STO P/EJECT Button  
Press once to stop the tape. Press again to  
eject the tape.  
Press to scan through  
the TV/VCR channels.  
Or, when in Play mode,  
press to adjust the  
tracking. Details are on  
page 49.  
Press the CHANNEL Up  
button and the VOLUME  
Down button on the  
TV/VCR at the same  
time to display the pop up  
menu.  
REW (ind) Button  
When in Stop mode, press to rewind the  
tape at high speed. When in Play mode,  
press to rewind while the picture stays on-  
screen. Details are on page 50.  
PLAY Button  
Press to play a tape. Also, press to release  
Search or Still mode and return to normal  
playback. Details are on page 50.  
F.FW D Button  
VO LUME Up/Down  
Buttons  
Press to adjust the  
sound level.  
Press the CHANNEL Up  
button and the VOLUME  
Down button on the  
TV/VCR at the same  
time to display the pop  
up menu.  
When in Stop mode, press to fast forward  
the tape at high speed. When in Play mode,  
press to fast forward while the picture stays  
on-screen. Details are on page 50.  
REC(ord)/O TR Button  
Press once to start a recording. Details are on  
page 29. Or, press three to 18 times to start  
a one touch recording (an immediate timed  
recording, 30 minutes to eight hours long) of  
the channel you are watching. Details are on  
page 30.  
EARPHO NE Jack  
Connect headphones (not  
supplied) here for person-  
al listening.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Rear Panel 21  
ANT.  
ANT(enna) Jack  
Connect your antenna or cable here.  
Details are on pages six - seven.  
Antenna Hole  
Connect the stem of an indoor antenna  
here. Details are on page six.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
22 Remote Control Buttons  
SLEEP Button  
Press to set the sleep timer. Details are on page 41.  
PO W ER Button  
Press to turn on or off the TV/VCR.  
Num ber Buttons  
Use to select channels and to program TV/VCR functions (such  
as setting the clock).  
Channels 1 - 9  
To select, press 0, then press the channel you want to select.  
For example, to select channel 7, press 0, 7.  
Channels 100 and above  
To select, press the +100 button, then press the last two digits  
of the channel you want. For example, to select channel 117,  
press the +100 button, 1, 7.  
2
5
8
0
3
6
1
4
7
o
9
p
o
(Tape) SPEED Button  
Press to select the recording speed (SP, LP, or SLP).  
+100  
p
PLAY/Button  
o
Press to play a tape. Details are on page 28. Also, press to  
release Search or Still mode and return to normal playback.  
Details are on page 50.  
PLAY  
+
REW  
F.FWD  
Press to select an item in the pop up menu.  
STOP  
p
REW (ind)/Button  
When in Stop mode, press to rewind the tape at high speed.  
When in Play mode, press to rewind the tape while the picture  
stays on-screen. Details are on page 50.  
Press to change a setting of a pop up menu item.  
Press to adjust the picture controls. Details are on pages 24 - 25.  
REC(ord)/O TR Button  
Press once to start a recording. Details are on page 29. Or,  
press three to 18 times to start a one touch recording (an  
immediate timed recording, 30 minutes to eight hours long) of  
the channel you are watching. Details are on page 30.  
MENU Button  
Press to display the pop up menu.  
STATUS/EXIT Button  
Press to see the status display. Press again to remove the status  
display. Details are on page 26.  
Press to exit the on-screen menu.  
SMART SO UND Button  
Press to turn the Smart Sound feature on or off. Details are on  
page 44.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote Control Buttons (contd) 23  
ALT. CH (Alternate Channel) Button  
Press to return to the TV channel you were viewing immediately  
before switching to your current channel.  
CHANNEL Up/Down Buttons  
Press to scan through the TV/VCR’s channels.  
VO LUME Up/Down Buttons  
Press to adjust the sound level. If you press the VOLUME  
Up/Down buttons when the sound is muted, the sound will be  
restored.  
MUTE Button  
2
5
8
0
3
6
Press to eliminate the TV/VCR’s sound. Press again to return to  
the previous volume level.  
1
4
7
o
F.FW D/+ Button  
When in Stop mode, press to fast forward the tape at high speed.  
During tape playback, press to fast forward while the picture stays  
on-screen. Details are on page 50.  
9
p
o
+100  
Press to change a setting of a pop up menu item.  
Press to adjust the picture controls. Details are on pages 24 - 25.  
p
o
STO P/Button  
Press to stop tape playback or recording.  
Press to select an item in the pop up menu.  
PLAY  
+
REW  
F.FWD  
STOP  
PAUSE/STILL Button  
p
In Record mode, press to temporarily stop the recording (pause).  
Press again to resume recording. Details are on page 29. You can-  
not pause a One Touch Recording that is set for a specific length  
of time.  
During tape playback, press to freeze the picture (still). Each time  
you press the PAUSE/STILL button, the noise lines will change  
position on-screen. Details are on page 50.  
MEMO RY Button  
Press to memorize a tape position at which the real time counter  
was set to 0:00:00. Details are on page 48. Or, press to memorize  
the start and end position on a tape when setting up A-B Repeat  
Playback. Details are on pages 46 - 47.  
CLEAR Button  
Press to erase incorrect data when programming TV/VCR func-  
tions. Also, press to reset the real time counter. Details are on  
page 48.  
VCR PLUS+ Button  
Press to set a Timer Recording with the VCR Plus+ programming  
system. Details are on pages 36-39.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
24 Adjusting the Picture Controls  
Follow these steps to adjust the TV/VCR’s brightness, picture,  
color, tint, and sharpness.  
1
Press the MENU button to display the pop up m enu.  
TO ADJUST PRESS +/-  
B BRIGHTNESS  
+
PICTURE  
COLOR  
TINT  
SHARPNESS  
TV RESET  
2
5
8
0
3
6
1
4
7
o
9
p
o
+100  
2
p
Press the PLAY/button or the STO P/button to select  
the desired control (BRIGHTNESS, for exam ple).  
o
3
1
PLAY  
+
REW  
F.FWD  
STOP  
3
p
Press the REW (ind)/– button or the F.FW D/+ button to  
adjust the picture control. (Refer to the chart on page 25.)  
2
4
4
W hen you finish, press the STATUS/EXIT button.  
Helpful Hints  
The on-screen menus shown on  
page 25 will disappear from the  
TV/VCR screen if no adjustments  
are made within 60 seconds.  
The original settings will probably  
give you the best picture quality.  
To reset the picture controls to the  
original settings, press the MENU  
button, then press the PLAY/but-  
ton or the STOP/button to select  
TV RESET, then press the F.FWD/+  
button. TV RESET COMPLETED will  
appear on-screen briefly.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adjusting the Picture Controls (contd) 25  
Decrease  
decreased brightness  
decreased contrast  
paler  
Increase  
increased brightness  
increased contrast  
more brilliant  
more green  
BRIGHTNESS  
PICTURE  
CO LO R  
TINT  
SHARPNESS  
more purple  
softer  
clearer  
Press the REW(ind)/-  
button to decrease a  
picture control.  
Press the F.FWD/+  
button to increase a  
picture control.  
POWER  
STOP REW  
EJECT  
PLA
CHANNEL EARPHONE  
AUDIO VIDEO  
REC  
TO ADJUST PRESS +/-  
TO ADJUST PRESS +/-  
TO ADJUST PRESS +/-  
BRIGHTNESS  
B PICTURE  
COLOR  
BRIGHTNESS  
PICTURE  
B BRIGHTNESS  
PICTURE  
COLOR  
+
+
B COLOR  
TINT  
TINT  
+
TINT  
SHARPNESS  
TV RESET  
SHARPNESS  
TV RESET  
SHARPNESS  
TV RESET  
TO ADJUST PRESS +/-  
TO ADJUST PRESS +/-  
BRIGHTNESS  
PICTURE  
BRIGHTNESS  
PICTURE  
COLOR  
COLOR  
TINT  
B SHARPNESS  
TV RESET  
B TINT  
SHARPNESS  
TV RESET  
+
+
Press the STOP/▼  
Button  
Press the PLAY/▲  
Button  
Download from Www.Somanuals.com. All Manuals Search And Download.  
26 On-Screen Status Displays  
A status display, which includes the current time, channel, and  
other information (see illustration of the status display at right),  
will appear when you press the STATUS/EXIT button or certain  
function buttons. You can bring up the status display at any time  
by pressing the STATUS/EXIT button. Remove the status display  
by pressing this button again. The contents of the status display  
may vary.  
Function  
Button  
Pressed  
Channel  
Time  
O N MO DE:  
12:00 AM  
STOP  
Whenever a function button (REW(ind)/-, PLAY/, etc.) is  
pressed, the status display will appear for five seconds.  
CO UNTER O NLY MO DE:  
CH10  
When a function button (REW(ind)/-, Play/, etc.) is pressed,  
the status display will appear for five seconds. After five sec-  
onds, only the counter will remain on-screen. To remove it,  
choose ON or OFF in the ON-SCREEN MODE menu. (There  
is an exception. When you press the STOP/button, the sta-  
tus display will appear for five seconds, then disappear.)  
O FF MO DE:  
The status display will not appear when you press a function  
button. The channel number will appear briefly when you select  
a channel if channels are programmed.  
SLP  
M 1:23:45  
Counter  
and  
Counter  
Memory  
Tape  
Speed  
To choose an ON-SCREEN MODE, follow the steps below.  
1
Press the MENU button to display the pop up m enu.  
2
Press the PLAY/button or the STO P/button to select  
VCR SETUP. Then, press the F.FW D/+ button.  
3
Helpful Hints  
Press the Num ber 3 button to select O N-SCREEN  
MO DE.  
If the channel you select has no  
broadcast, the screen will be solid  
blue. The screen will remain blue  
until you select an active channel.  
Channel numbers (when tuned)  
appear on-screen for a few seconds.  
The channel number will remain on-  
screen at all times (except during  
tape playback) if REMINDER is set  
to ON. Details are on page 27.  
You cannot view closed captions of a  
tape when the TV/VCR is in Counter  
Only mode. The counter display will  
replace the closed captioning display  
on the TV/VCR screen. Details are on  
pages 42 - 43.  
4
Press the Num ber 1 button to select O N, the Num ber 2  
button to select CO UNTER O NLY, or the Num ber 3 but-  
ton to select O FF. Your selection will appear on-screen.  
5
Press the STATUS/EXIT button.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Reminder 27  
The channel number will remain on-screen at all times when you  
set REMINDER to ON in the pop up menu. The exception is dur-  
ing tape playback, Forward and Reverse Searching, and Still modes,  
and when closed captioning is selected (CAPTION in the pop up  
menu).  
Set REMINDER to ON or OFF by following the steps below.  
1
Press the MENU button to display the pop up m enu.  
2
5
8
0
3
1
4
7
6
9
o
TO ADJUST PRESS +/-  
p
o
OFF  
B REMINDER  
BRIGHTNESS  
PICTURE  
+100  
COLOR  
TINT  
p
SHARPNESS  
o
3
1
PLAY  
+
REW  
F.FWD  
STOP  
2
p
Press the PLAY/button or the STO P/button to select  
REMINDER.  
2
4
3
Press the REW (ind)/– button or the F.FW D/+ button to  
select O N or O FF. Each press of the REW(ind)/– button or the  
F.FWD/+ button turns REMINDER ON or OFF.  
TO ADJUST PRESS +/-  
CH12  
ON  
B REMINDER  
BRIGHTNESS  
PICTURE  
COLOR  
TINT  
SHARPNESS  
4
Press the STATUS/EXIT button.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
28 Playing  
Follow the steps below to play a tape.  
Insert a tape in the TV/VCR.  
1
5
1
Press the STOP/EJECT button  
on the TV/VCR.  
Insert a tape in the TV/VCR. The power will come on. If the  
tapes record tab has been removed, playback should start auto-  
matically.  
2
2
5
8
0
3
6
1
4
7
If playback does not start autom atically, press the  
PLAY/button to start playback.  
o
9
p
o
+100  
3
p
Press the STO P/button on the rem ote control or the  
STO P/EJECT button on the TV/VCR once to stop play-  
back.  
o
2
3
PLAY  
+
REW  
F.FWD  
4
STOP  
p
4
Press the REW (ind)/- button to rewind the tape.  
5
W hen the tape has finished rewinding, press the  
STO P/EJECT button on the TV/VCR to rem ove the tape.  
Helpful Hints  
If the tape you want to play is  
already in the TV/VCR, turn on the  
TV/VCR power, then press the  
PLAY/button.  
Playback features and options are  
on pages 41 - 50.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Recording 29  
Read and follow the steps below to record a TV program.  
1
Place a tape with its record tab intact (see page five) in  
the TV/VCR. The power will come on. O r, if the tape is  
already in the TV/VCR, press the PO W ER button.  
2
1
Press the (Tape) SPEED button until the desired tape  
speed appears on the TV/VCR screen. Details about tape  
speed are given below.  
2
3
6
1
4
7
5
8
0
o
9
p
o
3
5
+100  
3
p
Use the CHANNEL Up/Down buttons or the Num ber  
buttons to select the channel to be recorded. (Channels  
cannot be changed during recording.)  
o
2
6
PLAY  
+
REW  
F.FWD  
STOP  
p
4
Press the REC(ord)/O TR button once to start recording.  
The REC(ord) light will glow.  
If there is not a tape in the TV/VCR, NO CASSETTE flashes on-  
screen briefly.  
4
If the tape does not have a record tab, PROTECTED CAS-  
SETTE / CANNOT RECORD flashes on-screen briefly. The  
TV/VCR will eject the tape. Replace it with another tape.  
5
To pause the recording (for exam ple, during com m er-  
cials), press the PAUSE/STILL button. The REC(ord) light  
will flash. To resum e recording, press the PAUSE/STILL  
button again or the REC(ord)/O TR button. The REC(ord)  
light will glow.  
6
To stop recording, press the STO P/button.  
Helpful Hints  
Recording options are on pages 30  
- 39.  
You cannot record if the TV/VCR is  
in Record Defeat mode (REC  
DEFEATED will flash on-screen).  
Details are on page 40.  
Tape Speeds  
This chart shows the recording/playback time for three types of  
video cassettes (T160, T120, and T60). There are three playback  
speeds: SP, LP, and SLP. During playback, the TV/VCR selects  
the tape speed automatically. When recording, you can change  
the tape speed using the (Tape) SPEED button (see page 22).  
If you pause a recording for more  
than five minutes, the TV/VCR will  
switch to Stop mode automatically  
to protect the video cassette tape  
from damage.  
You can change the tape speed  
with the (Tape) SPEED button while  
a recording is in progress, but some  
distortion may appear on the tape.  
Tape Speed  
Type  
SP  
(Standard Play)  
LP  
(Long Play)  
SLP  
Maximum Record/Playback Time  
T160  
2 hrs.  
40 mins.  
5 hrs.  
T120  
T60  
2 hrs.  
1 hr.  
4 hrs.  
6 hrs.  
2 hrs.  
3 hrs.  
20 mins.  
8 hrs.  
(Super Long Play)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
30 One Touch Recording  
The one touch recording (OTR) function allows you to program  
an immediate timed recording from 30 minutes to eight hours  
long without setting the timer.  
Before you begin, make sure:  
Channels are programmed.  
Press the STOP/EJECT but-  
ton on the TV/VCR to stop  
the OTR.  
4
There is a tape in the TV/VCR. The record tab must be intact.  
2
5
8
0
3
6
1
4
7
1
o
Use the CHANNEL Up/Down buttons or the Num ber  
buttons to select the channel you want to record.  
9
p
o
1
+100  
p
o
2
3
2
PLAY  
Press the (Tape) SPEED button until the desired record-  
ing speed (SP, LP, or SLP) appears on-screen. Details are on  
page 29.  
+
REW  
F.FWD  
STOP  
p
3
Press the REC(ord)/O TR button repeatedly, until the  
desired recording length appears in the upper right corner of the  
screen. Recording will begin immediately. The REC(ord) light will  
appear.  
OTR  
LENGTH 0:30  
CH12  
Helpful Hints  
LENGTH  
CANCEL  
:
:
PRESS OTR  
PRESS CLEAR  
To check the time remaining for an  
OTR after the OTR has been set,  
press the STATUS/EXIT button.  
To change the recording length  
while an OTR is in progress, press  
the REC(ord)/OTR button until the  
desired recording length appears  
on-screen.  
You can not pause an OTR.  
To cancel an OTR, but continue  
recording, press the REC(ord)/OTR  
button, then press the CLEAR button.  
You cannot record if the TV/VCR is  
in Record Defeat mode. Details are  
on page 40.  
4
To stop an O TR before recording is finished, press the  
STO P/EJECT button on the TV/VCR.  
O r, press the REC(ord)/O TR button, then press the  
CLEAR button, then press the STO P/button on the  
rem ote control.  
You can change the tape speed  
with the (Tape) SPEED button while  
a recording is in progress, but some  
distortion may appear on the tape.  
If the end of the tape is reached  
during an OTR, recording will stop.  
The TV/VCR will eject the tape and  
shut itself off. The REC(ord) light  
may flash.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Rerecording (Tape Duplication) 31  
Source Unit  
(VCR or Cam corder)  
POWER  
STOP  
AUDIO VIDEO  
VIDEO AUDIO  
OUT  
REC  
EJECT  
IN  
From AUDIO OUT to AUDIO  
AUDIO and  
VIDEO OUT  
Jacks  
AUDIO and  
VIDEO Jacks  
on TV/VCR  
From VIDEO OUT to VIDEO  
1
Make the connections shown above, using audio and video  
cables.  
2
The source unit (VCR or camcorder) will play your tape. Insert a  
prerecorded tape in the source unit. If playback begins, press  
the STOP button on the unit.  
3
The TV/VCR will record your tape. Insert a blank tape in the  
TV/VCR. Make sure the tapes record tab is intact. The TV/VCR  
will turn on automatically.  
4
Point the rem ote control at the TV/VCR. Press Num ber  
buttons 0, 0 so that A/V IN appears on-screen.  
5
Point the rem ote control at the TV/VCR. Press the  
(Tape) SPEED button until the desired tape speed (SP,  
LP, or SLP) appears on-screen.  
Helpful Hints  
6
• Unauthorized recording of copy-  
righted television programs, video  
tapes, or other materials may  
infringe on the rights of copyright  
owners and violate copyright laws.  
• Different brands of equipment may  
operate differently.  
• Make sure all connections are  
secure. Otherwise, you may not  
record both picture and sound.  
Audio and video cables are not  
included.  
Press the PLAY button on the source unit and the  
REC(ord)/O TR button on your TV/VCR at the sam e tim e.  
Copying will begin.  
7
To stop copying, press the STO P/EJECT button on the  
TV/VCR, then stop the tape on the source unit (VCR or  
cam corder).  
Download from Www.Somanuals.com. All Manuals Search And Download.  
32 Timer Recording  
Follow the steps below to program the TV/VCR to record TV  
programs while youre away from home. You can program up to  
eight timer recordings. For each one, the TV/VCR will turn itself  
on, record, and turn itself off automatically. Before you begin  
make sure:  
The clock has been set. If not, CLOCK MUST BE SET appears.  
Channels are programmed.  
There is a tape in the TV/VCR (make sure the tapes record tab  
is intact and the tape is long enough to record the program).  
2
5
8
0
3
6
1
4
7
Com plete each step within 60 seconds of com pleting the  
previous step. If you dont, you m ay start again at step 1.  
3
o
9
p
o
+100  
1
Press the MENU button to display the pop up m enu.  
p
o
PLAY  
2
1
+
REW  
F.FWD  
PRIM. SETUP  
STOP  
PRESS +  
B VCR PROGRAM  
VCR SETUP  
p
CAPTION  
REMINDER  
BRIGHTNESS  
2
Press the PLAY/button or the STO P/button to select  
VCR PRO GRAM, then press the F.FW D/+ button.  
VCR PROGRAM  
1 ONCE  
2 DAILY (MON - FRI)  
3 WEEKLY  
4 PROGRAM REVIEW  
TO SELECT PRESS NUMBER  
TO END PRESS EXIT  
3
Select a once, daily or weekly recording.  
Press the Number 1 button to select ONCE. The TV/VCR will  
record a TV program on any day you choose, up to 12 months  
away.  
Press the Number 2 button to select DAILY. The TV/VCR will  
record from Monday through Friday – starting at the same time  
and recording for the same length of time every day.  
Press the Number 3 button to select WEEKLY. The TV/VCR  
will record on the same day, at the same time, and for the same  
length of time every week.  
Helpful Hints  
If the power fails, programmed  
timer recordings will be lost.  
You cannot set a timer recording if  
the TV/VCR is in Record Defeat  
mode. To set the Record Defeat  
mode to OFF, see page 40.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Timer Recording (contd) 33  
4
Use the Num ber buttons (1 - 8) to select a position in  
which to store the tim er recording. Flashing numbers indi-  
cate an open position (one in which a timer recording has not yet  
been stored).  
4-7  
NOTE: If you select a number that has already been used to store a  
timer recording, PREVIOUSLY SET PROGRAM will appear on-screen for  
a few seconds. Then information about the program in that position  
will appear on-screen. If this happens, press the STATUS/EXIT button.  
Then use the Number buttons to select another position.  
2
5
8
0
3
6
1
4
7
o
9
p
o
5
+100  
Enter the channel of the TV program you want to record (you  
must enter a 0 before all single digit channels).  
If you are recording from line input, press 0, 0. A/V IN will  
appear on-screen.  
p
o
PLAY  
+
REW  
F.FWD  
STOP  
If you are recording using a Cable Box,enter the Cable Box out-  
put channel (03 or 04). Be sure to select the channel at the  
Cable Box and leave the Cable Box on for the timer recording.  
p
ONE TIME PROGRAM  
PROGRAM  
1
CHANNEL – –  
TO CORRECT PRESS CLEAR  
TO END PRESS EXIT  
6
Press two Num ber buttons for the hour(s) you want the  
recording to begin. Press two Num ber buttons for the  
m inute(s) you want the recording to begin. Press 1 for  
AM or 2 for PM. For example, for 9:30 PM, press 09, 30, 2.  
ONE TIME PROGRAM  
PROGRAM  
1
CHANNEL 10  
TIME ON  
– – : – –  
TO CORRECT PRESS CLEAR  
TO END PRESS EXIT  
Helpful Hints  
If the numbers entered do not  
match the TV/VCR’s internal calen-  
dar, the entry will be rejected and a  
question mark (?) will appear on  
the TV/VCR screen.  
7
Follow the instructions in step 6 to set the recordings  
stop tim e. (AM or PM will be set automatically.)  
ONE TIME PROGRAM  
PROGRAM  
1
To make corrections while you are  
programming a timer recording,  
press the CLEAR button until the  
cursor is flashing on the item you  
want to change. Then enter the cor-  
rect information.  
CHANNEL 10  
TIME ON  
09:30 PM  
TIME OFF – – : – –  
TO CORRECT PRESS CLEAR  
TO END PRESS EXIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
34 Timer Recording (contd)  
8
Press the Num ber 1 button to record in SP speed, press  
the Num ber 2 button to record in LP speed, or press the  
Num ber 3 button to record in SLP speed. Details about tape  
speed are on page 29. You cannot use the (Tape) SPEED button at  
this time.  
11 8  
ONE TIME PROGRAM  
PROGRAM  
1
CHANNEL 10  
2
5
8
0
3
6
1
4
7
TIME ON  
09:30 PM  
TIME OFF 11:00 PM  
REC SPEED SLP  
SP=1 LP=2 SLP=3  
o
9
9
p
o
TO CORRECT PRESS CLEAR  
TO END PRESS EXIT  
+100  
p
o
PLAY  
9
+
REW  
F.FWD  
Press two Num ber buttons for the m onth and two  
Num ber buttons for the day you want the program to  
record. For example, for July 10, 1997, press 07, 10. The day of  
the week and the year will be displayed automatically (you cannot  
program the TV/VCR to record more than one year in advance).  
ONE TIME PROGRAM  
STOP  
p
10  
PROGRAM  
1
CHANNEL  
TIME ON  
TIME OFF  
REC SPEED  
10  
09:30 PM  
11:00 PM  
SLP  
START DATE 07/10/97  
THURSDAY  
TO CORRECT PRESS CLEAR  
TO END PRESS EXIT  
10  
Press the STATUS/EXIT button. PROGRAM WAS COM-  
PLETED / PLEASE TURN OFF FOR TIMER RECORDING will  
appear on-screen.  
If there is not a tape in the TV/VCR, PLEASE INSERT CAS-  
SETTE also appears on-screen.  
If there is a tape without a record tab in the TV/VCR, PLEASE  
REMOVE CASSETTE also appears on-screen. If this happens,  
insert a different tape.  
If PROGRAM NOT COMPLETED appears, start again at step 1.  
In five seconds the on-screen message will disappear.  
Helpful Hints  
PROGRAM NOT COMPLETED /  
CLASH may appear on-screen when  
you finish setting a timer recording.  
This means that the timer recording  
you just programmed and another  
timer recording overlap, and thus  
the current timer recording will not  
be carried out.  
11  
Turn off the TV/VCR power. The REC(ord) light will flash. If  
you forget to turn off the TV/VCR, PLEASE TURN OFF FOR  
TIMER RECORDING appears on the TV/VCR screen two minutes  
before a timer recording starts.  
To stop a started timer recording,  
press the STOP/EJECT button on  
the TV/VCR.  
Please see page 52 for more  
Helpful Hints.  
The TV/VCR m ust be off for a tim er  
recording to take place!  
Make sure there is a tape in the TV/VCR.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Timer Recording (contd) 35  
Checking or Clearing Tim er Recordings  
1
W ith the TV/VCR on, press the MENU button.  
2
Press the PLAY/button or the STO P/button to select  
VCR PRO GRAM, then press the F.FW D/+ button.  
4
2
5
8
0
3
6
1
4
7
o
3
3
9
p
o
Press the Num ber 4 button to select PRO GRAM  
REVIEW . The timer recording information for the program in  
the lowest numbered position will appear on-screen. If no timer  
recordings are programmed, nothing will happen when you press  
the Number 4 button.  
+100  
p
o
PLAY  
2
+
REW  
F.FWD  
STOP  
p
4
Press the Num ber 1 button to display inform ation about  
the next program m ed tim er recording. (If you do not press  
a button within 10 seconds, information about the next pro-  
grammed timer recording will appear.) This will continue until all  
positions have been displayed. Then, the menu will disappear. You  
can exit the Program Review at any time by pressing the STA-  
TUS/EXIT button.  
1
5
5
To cancel the tim er recording displayed, press the  
CLEAR button. Then, press the STATUS/EXIT button.  
6
Repeat steps 1 - 4 to m ake sure you have cleared the  
correct position.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
36 Setting Up the VCR Plus+ Programming System  
1
First, fill in the boxes on this page. It will only take a few minutes, and you must do it if you want the VCR  
Plus+ programming system to work properly.  
Since the channel numbers of the stations you receive may not be the same as the station numbers, and  
since channel numbers differ from area to area, you must program the TV/VCR with your local channel  
information. To fill in the boxes, you will need 1) a cable channel line-up list, if applicable (you can request  
one from your cable company), and 2) a chart that lists VCR Plus+ channel numbers, which you can find in  
your TV guide or the TV listings of your local newspaper.  
TV Channels  
CABLE Channels  
Local TV  
Stations  
Local TV  
Stations  
VCR PLUS+ CH.  
VCR PLUS+ CH.  
CABLE/TV CH.  
CABLE/TV CH.  
(call letters)  
(call letters)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting Up the VCR Plus+ Programming System (contd) 37  
Examine the lists on  
page 36.  
2
2
Now, compare the channel numbers you have written in the VCR  
PLUS+ CH. and CABLE/TV CH. columns. Youll notice that some  
stations have VCR Plus+ and Cable/TV channel numbers that are  
the same, and other stations have channel numbers that do not  
match. Where the channel numbers DO NOT match, you must  
tell the TV/VCR the VCR Plus+ and Cable/TV channel numbers  
according to the following steps.  
6
5
4
2
5
8
0
3
6
1
4
7
Make each entry within 60 seconds of the previous entry.  
o
9
p
o
+100  
3
p
Press the MENU button to display the pop up m enu.  
o
PLAY  
+
REW  
F.FWD  
STOP  
4
p
Press the PLAY/button or the STO P/button to select  
VCR SETUP, then press the F.FW D/+ button.  
VCR SETUP  
3
1 ONE TIME PLAY  
2 REPEAT PLAY  
3 ON-SCREEN MODE  
4 RECORD DEFEAT  
5 VCR PLUS+ REF. MAP  
[ON]  
7
[OFF]  
TO SELECT PRESS NUMBER  
TO END PRESS EXIT  
5
Press the Num ber 5 button to select VCR PLUS+ REF. MAP.  
VCR PLUS+ CROSS REF. MAP  
VCR PLUS+  
124  
CABLE/TV  
– –  
125  
– –  
01 – – – – B – –  
02  
03  
– –  
– –  
TO SELECT CH PRESS CH /▼  
THEN ENTER CH NO.  
TO END PRESS EXIT  
6
Look at the lists you filled in on page 36. For stations whose  
VCR Plus+ and Cable/TV channels do not m atch, press  
the CHANNEL (Up/Down) buttons until the arrow is  
beside the VCR Plus+ channel you need. Then, press the  
Num ber buttons to enter the corresponding Cable/TV  
channel from your list. (Enter a “0” before single-digit chan-  
nels.) Continue this process until you have entered all the stations  
on your list.  
Helpful Hints  
To correct a Cable/TV channel num-  
ber, repeat the steps on this page.  
To clear a Cable/TV channel number,  
repeat steps 3-5 on this page. Then,  
press the CHANNEL (Up/Down) but-  
tons to select it. Then press the  
CLEAR button. Press the  
STATUS/EXIT button to exit.  
Always enter a “0” before single-  
digit channels.  
VCR PLUS+ CROSS REF. MAP  
VCR PLUS+  
124  
CABLE/TV  
– –  
125  
– –  
01 – – – – B 23  
02  
03  
– –  
– –  
TO SELECT CH PRESS CH /▼  
TO DELETE PRESS CLEAR  
TO END PRESS EXIT  
To select line input for the Cable/TV  
channel, press 0,0. A/V IN will  
appear on-screen.  
7
Press the STATUS/EXIT button to exit.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
38 Timer Recording With the VCR Plus+ Programming System  
Follow the steps below to program a timer recording using the  
PlusCode programming numbers in your TV guide. Before you  
begin, make sure:  
The clock has been set. If not, CLOCK MUST BE SET appears.  
Channels are programmed.  
There is a tape in the TV/VCR (make sure the tapes record tab  
is intact and the tape is long enough to record the program).  
You have completed the steps on pages 36-37.  
2
5
8
0
3
6
1
4
7
3
o
2
1
9
p
o
Com plete each step within 60 seconds of com pleting the  
previous step. If you dont, you m ay return to step 1.  
+100  
p
o
PLAY  
1
+
REW  
F.FWD  
STOP  
Press the VCR PLUS+ button on the remote control. The on-  
screen display shown below will appear.  
VCR PLUS+ PROGRAM  
p
PLUS CODE : – – – – – – – –  
TO END PRESS EXIT  
2
Press the Num ber buttons to enter the PlusCode pro-  
gram m ing num ber of the program you wish to record (this  
number is different for every program, and it can be four to eight  
digits long). Finally, press the VCR PLUS+ button.  
VCR PLUS+ PROGRAM  
PLUS CODE : 60590 – – –  
TO SET PRESS VCR +  
TO CORRECT PRESS CLEAR  
TO END PRESS EXIT  
Helpful Hints  
If the power fails, programmed timer  
recordings will be lost.  
You cannot set a timer recording if  
the TV/VCR is in Record Defeat  
mode. To set the Record Defeat  
mode to OFF, see page 40.  
If CODE ERROR flashes after you  
enter the PlusCode programming  
number and press the VCR PLUS+  
button, the number you entered was  
incorrect (for example, too short). If  
this happens, enter the correct num-  
ber.  
3
To record the program once, press the Num ber 1 button  
to select O NCE. To record the sam e program every day  
from Monday through Friday, press the Num ber 2 button  
to select DAILY. To record the sam e program every  
week on the sam e day (such as every Saturday), press the  
Num ber 3 button to select W EEKLY.  
VCR PLUS+ PROGRAM  
1 ONCE  
2 DAILY (MON - FRI)  
3 WEEKLY  
CLASH may flash on the screen after  
you complete step 2. This means  
that the timer recording you just pro-  
grammed and another timer record-  
ing overlap, and thus the current  
timer recording will not be carried  
out.  
TO SELECT PRESS NUMBER  
TO END PRESS EXIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Timer Recording With the VCR Plus+ Programming System (contd) 39  
4
6
4
Press the Num ber 1 button to record in SP speed, the  
Num ber 2 button to record in LP speed, or the Num ber 3  
button to record in SLP speed. Your selection will appear to  
the right of REC SPEED on-screen, although SP=1 LP=2 SLP=3 will  
continue to flash. For details about tape speed, see pages 29 and  
51. You cannot use the (Tape) SPEED button at this time.  
2
5
8
0
3
6
1
4
7
o
9
p
o
+100  
ONE TIME PROGRAM  
PROGRAM  
1
p
CHANNEL  
TIME ON  
TIME OFF  
REC SPEED  
09  
o
10:30 PM  
11:30 PM  
SLP  
PLAY  
+
REW  
F.FWD  
SP=1 LP=2 SLP=3  
START DATE  
10/10/97  
FRIDAY  
STOP  
p
TO END PRESS EXIT  
5
5
Press the STATUS/EXIT button. PROGRAM WAS COM-  
PLETED / PLEASE TURN OFF FOR TIMER RECORDING will  
appear on-screen.  
If there is not a tape in the TV/VCR, PLEASE INSERT CAS-  
SETTE also appears on-screen.  
If there is a tape without a record tab in the TV/VCR, PLEASE  
REMOVE CASSETTE also appears on-screen. If this happens,  
insert a different tape.  
6
Turn off the TV/VCR power. The REC(ord) light will flash. If  
you forget to turn off the TV/VCR, PLEASE TURN OFF FOR  
TIMER RECORDING appears on the TV/VCR screen two minutes  
before a timer recording starts.  
Helpful Hints  
To exit the VCR Plus+ programming  
system at any time, press the STA-  
TUS/EXIT button. The display will  
disappear from the screen.  
To stop a started timer recording,  
press the STOP/EJECT button on  
the TV/VCR.  
The TV/VCR m ust be off for  
a tim er recording to take  
place! Make sure there is a  
tape in the TV/VCR.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
40 Record Defeat  
Record Defeat  
Follow the steps below to prevent accidental recording.  
1
Press the MENU button to display the pop up m enu.  
PRIM. SETUP  
VCR PROGRAM  
B VCR SETUP  
CAPTION  
PRESS +  
2
5
8
0
3
6
1
4
7
REMINDER  
BRIGHTNESS  
o
3
2
9
p
o
+100  
2
p
Press the PLAY/button or the STO P/button to select  
VCR SETUP, then press the F.FW D/+ button.  
o
PLAY  
+
REW  
F.FWD  
VCR SETUP  
STOP  
1 ONE TIME PLAY  
2 REPEAT PLAY  
3 ON-SCREEN MODE  
4 RECORD DEFEAT  
5 VCR PLUS+ REF. MAP  
[ON]  
[OFF]  
p
TO SELECT PRESS NUMBER  
TO END PRESS EXIT  
1
4
3
Press the Num ber 4 button so that O N appears to the  
right of RECO RD DEFEAT.  
4
Press the STATUS/EXIT button.  
5
Now, REC DEFEATED will flash on-screen when you  
press the REC(ord)/O TR button.  
Helpful Hints  
If you put the TV/VCR in Record  
REC DEFEATED  
Defeat mode after a timer recording  
has been programmed, the timer  
recording will not be carried out.  
If you put the TV/VCR in Record  
Defeat mode, then try to program a  
timer recording, you will not be able  
to program a timer recording. VCR  
PROGRAM cannot be selected from  
the pop up menu.  
To take the TV/VCR out of Record  
Defeat mode, repeat steps 1 - 2  
above. At step 3, press the  
Number 4 button so that OFF  
appears to the right of RECORD  
DEFEAT on-screen. Press the STA-  
TUS/EXIT button.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the Sleep Timer 41  
Use the sleep timer to program the TV/VCR to shut off in a cer-  
tain amount of time.  
1
1-2  
Press the SLEEP button. The sleep timer display will appear  
on-screen. (You can not set the sleep timer during a recording.)  
2
5
8
0
3
6
1
4
7
SLEEP  
0
MIN  
o
9
p
o
+100  
2
p
W ithin five seconds, press the SLEEP button repeatedly  
to select 30 m inutes, 60 m inutes, 90 m inutes, or 120 m in-  
utes. In a few seconds, the display will disappear. Then the  
TV/VCR will shut itself off after the specified amount of time.  
One minute before the TV/VCR shuts itself off, the seconds will  
count down on-screen.  
o
PLAY  
+
REW  
F.FWD  
STOP  
p
GOOD NIGHT appears on the TV/VCR screen 10 seconds  
before the TV/VCR shuts itself off.  
SLEEP 10 SEC  
GOOD NIGHT  
To see how much time remains until the TV/VCR shuts itself  
off, press the SLEEP button once. The time remaining will  
appear on-screen briefly. You cannot do this during a recording.  
To cancel a sleep timer setting, press the SLEEP button until 0  
MIN appears on-screen. The on-screen display will disappear in  
a few seconds. You cannot cancel it during a recording.  
Helpful Hints  
You can start a recording after the  
sleep timer is set. If the recording  
finishes before the TV/VCR shuts  
itself off, the TV/VCR will shut itself  
off as programmed with the sleep  
timer. If a recording is in progress,  
the TV/VCR will not shut itself off  
until recording stops.  
• A timer recording will not begin  
until after the TV/VCR shuts itself  
off. Two minutes before a timer  
recording starts, PLEASE TURN OFF  
FOR TIMER RECORDING flashes  
on-screen. If you see this message,  
turn off the TV/VCR.  
If the power fails, you might lose  
the sleep timer setting.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
42 Closed Captioning  
When you watch a program that is being broadcast with closed  
captioning, you can access on-screen boxes containing the pro-  
grams dialogue (for example, what a character is saying), dialogue  
in a foreign language, or information (such as a channel guide,  
schedule, or announcements). Follow the steps below to select  
closed captioning.  
Not all TV programs and commercials are broadcast with closed  
captioning. Similarly, all types of closed captioning (second lan-  
guage, full-screen text, etc.) are not always broadcast. If closed  
captioning is not broadcast, you cannot receive it. This does not  
indicate a problem with the TV/VCR. Refer to your areas TV  
program listings for the shows offered with closed captioning.  
2
5
8
0
3
6
1
4
7
o
9
p
o
+100  
1
p
Press the MENU button to display the pop up m enu.  
o
3
1
PLAY  
TO ADJUST PRESS +/-  
+
REW  
F.FWD  
STOP  
B CAPTION  
REMINDER  
BRIGHTNESS  
PICTURE  
COLOR  
OFF  
p
2
TINT  
2
Press the PLAY/button or the STO P/button to select  
CAPTIO N.  
3
Press the REW (ind)/– button or the F.FW D/+ button to  
select your desired m ode.  
The selected closed captioning mode will appear to the right of  
CAPTION on-screen.  
CAPTION1 displays standard closed captioning (what a charac-  
ter is saying).  
CAPTION2 displays foreign language closed captioning (foreign  
language words showing what a character is saying).  
TEXT1 and TEXT2 display half screen text (such as a channel  
guide, schedule, or announcement).  
OFF turns closed captioning off. Captions will not appear on-  
screen.  
TO ADJUST PRESS +/-  
Exam ple:  
CAPTIO N1  
Menu  
CAPTION1  
B CAPTION  
REMINDER  
BRIGHTNESS  
PICTURE  
COLOR  
Screen  
TINT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Closed Captioning (contd) 43  
4
Press the STATUS/EXIT button. The type of closed caption-  
ing you selected at step 3 will appear on-screen. (If it does not,  
see Helpful Hints below. The program must be broadcast with  
closed captioning.)  
2
5
8
0
3
6
1
4
7
o
9
p
o
+100  
HELLO  
p
o
Standard Closed Captioning  
PLAY  
+
REW  
F.FWD  
STOP  
p
WORLD WEEATHER  
5 C  
8 C  
7 C  
23:00  
20:00  
4:00  
CLOUD  
RAIN  
CLOUD  
NYL  
LOS  
LONDON  
4
Text Screen  
Helpful Hints  
You cannot view closed captioning  
of a tape when the TV/VCR is in  
Counter Only mode. Details are on  
page 26.  
Abbreviations, symbols, and other  
grammatical shortcuts are often  
used in order to keep pace with the  
on-screen action. This does not indi-  
cate a problem with the TV/VCR.  
To cancel closed captioning, follow  
steps 1 - 2 on page 42. At step 3,  
press the REW(ind)/– button or the  
F.FWD/+ button to select OFF.  
Press the STATUS/EXIT button.  
• When you change channels, the  
closed captioning may be delayed  
for a few seconds.  
• When you adjust the volume or  
mute the volume, closed captioning  
may be delayed for a few seconds.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
44 Volume Bar / Smart Sound  
Volum e Bar  
Usually, the volume bar appears when you press the VOLUME  
Up/Down buttons. If you do not need it, set the VOLUME BAR to  
OFF position. For example, when you watch a program that is  
being broadcast with closed captioning, you may choose to set the  
VOLUME BAR to OFF position so the captions can remain on-  
screen. The captions will remain on-screen even when you press  
the VOLUME Up/Down buttons or the MUTE button.  
To turn Volume Bar On or Off ...  
2
5
8
0
3
6
1
4
7
o
3
2
9
p
o
1
+100  
Press the MENU button to display the pop up m enu.  
p
o
PLAY  
+
REW  
F.FWD  
PRESS +  
B PRIM. SETUP  
VCR PROGRAM  
VCR SETUP  
STOP  
p
CAPTION  
REMINDER  
BRIGHTNESS  
1
2
4
Press the PLAY/button or the STO P/button to select  
PRIM. SETUP. Then, press the F.FW D/+ button.  
PRIMARY SETUP  
1 SELECT LANGUAGE  
2 AUTO PROGRAMMING  
3 ADD/DELETE CHANNEL  
4 CH. MEMORY REVIEW  
5 VOLUME BAR  
6 SET CLOCK  
[ON]  
TO SELECT PRESS NUMBER  
TO END PRESS EXIT  
To turn Smart Sound On or Off ...  
3
Press the Num ber 5 button so that O FF appears to the  
right of VO LUME BAR. Each press of the Number 5 button  
will turn the VOLUME BAR ON or OFF.  
2
5
8
0
3
6
1
4
7
o
4
9
p
o
Press the STATUS/EXIT button.  
+100  
p
Sm art Sound  
o
The Smart Sound feature stabilizes the TV/VCR volume. For  
example, when Smart Sound is turned On, the volume will not  
increase suddenly during commercials or loud segments of pro-  
gramming. The volume will stay at the same level.  
PLAY  
+
REW  
F.FWD  
STOP  
p
1
1
Press the SMART SO UND button on the rem ote control  
to select O N (or O FF). The on-screen display shown below  
will appear for 10 seconds.  
SMART SOUND  
ON  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Repeat Playback 45  
Follow the steps below to program the TV/VCR to play a tape  
over and over.  
1
Press the MENU button to display the pop up m enu.  
PRIM. SETUP  
VCR PROGRAM  
PRESS +  
B VCR SETUP  
CAPTION  
2
5
8
0
3
6
REMINDER  
BRIGHTNESS  
1
4
7
3
4
o
9
p
o
+100  
2
Press the PLAY/button or the STO P/button to select  
VCR SETUP, then press the F.FW D/+ button.  
p
o
PLAY  
2
1
VCR SETUP  
+
REW  
F.FWD  
STOP  
1 ONE TIME PLAY  
2 REPEAT PLAY  
3 ON-SCREEN MODE  
4 RECORD DEFEAT  
5 VCR PLUS+ REF. MAP  
[ON]  
[OFF]  
p
TO SELECT PRESS NUMBER  
TO END PRESS EXIT  
3
Press the Num ber 2 button so that O N appears to the  
right of REPEAT PLAY.  
VCR SETUP  
1 ONE TIME PLAY  
2 REPEAT PLAY  
3 ON-SCREEN MODE  
4 RECORD DEFEAT  
5 VCR PLUS+ REF. MAP  
[ON]  
[OFF]  
TO SELECT PRESS NUMBER  
TO END PRESS EXIT  
4
Press the STATUS/EXIT button. Now, when a tape has fin-  
ished playing, the TV/VCR will rewind it and start playback again.  
(TV programming will appear while the tape is rewinding.)  
Helpful Hints  
The TV/VCR will stay in Repeat Play  
mode until you select ONE TIME  
PLAY mode, even if the TV/VCR is  
turned off. To exit Repeat Play  
mode, follow steps 1 and 2 above.  
At step 3, press the Number 1 but-  
ton so that ON appears to the right  
of ONE TIME PLAY. Press the STA-  
TUS/EXIT button.  
The time counter memory will not  
function during Repeat Play mode.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
46 A - B Repeat Playback  
Follow the steps below to program the TV/VCR to play the mate-  
rial between two specified points (A and B) on a tape over and  
over again.  
Insert a tape in the TV/VCR.  
1
1
Insert a tape in the TV/VCR.  
2
Press the MENU button to display the pop up m enu.  
2
5
8
0
3
6
1
4
7
o
4
3
2
9
p
o
PRIM. SETUP  
VCR PROGRAM  
B VCR SETUP  
CAPTION  
REMINDER  
BRIGHTNESS  
+100  
PRESS +  
p
o
PLAY  
+
REW  
F.FWD  
STOP  
3
p
Press the PLAY/button or the STO P/button to select  
VCR SETUP, then press the F.FW D/+ button.  
VCR SETUP  
1 ONE TIME PLAY  
2 REPEAT PLAY  
3 ON-SCREEN MODE  
4 RECORD DEFEAT  
5 VCR PLUS+ REF. MAP  
[ON]  
[OFF]  
TO SELECT PRESS NUMBER  
TO END PRESS EXIT  
4
Press the Num ber 2 button repeatedly so that A-B  
appears to the right of REPEAT PLAY.  
VCR SETUP  
1 ONE TIME PLAY  
2 REPEAT PLAY  
[A-B]  
[OFF]  
3 ON-SCREEN MODE  
4 RECORD DEFEAT  
5 VCR PLUS+ REF. MAP  
TO SELECT PRESS NUMBER  
TO END PRESS EXIT  
Helpful Hints  
To cancel A-B Repeat Play mode,  
follow steps 2 - 3. At step 4, press  
the Number 1 button so that ON  
appears to the right of ONE TIME  
PLAY. Press the STATUS/EXIT but-  
ton.  
The end position (B) must be later  
on the tape than the start position  
(A).  
Download from Www.Somanuals.com. All Manuals Search And Download.  
A - B Repeat Playback (contd) 47  
5
Press the STATUS/EXIT button to rem ove the display. A-  
B REPEAT will appear on-screen. Beneath it, the letter A will flash  
beside the tape counter.  
.
2
5
8
0
3
6
1
4
7
A-B REPEAT  
0:00:00  
A
o
9
p
o
6
+100  
Play, fast forward, or rewind the tape to the position at  
which you want to begin playback. Stop the tape, then  
press the MEMO RY button to set the start position (A).  
The flashing A will become a flashing B.  
p
o
PLAY  
+
REW  
F.FWD  
STOP  
p
.
7
6
5
A-B REPEAT  
0:00:00  
B
7
Play or fast forward the tape to the position at which you  
want playback to end. Stop the tape, then press the  
MEMO RY button to set the end position (B).  
The length of time between the start position (A) and the end  
position (B) must be at least three minutes.  
8
The TV/VCR will immediately rewind the tape to the start posi-  
tion (A) and repeat playback to the end position (B) over and  
over.  
Helpful Hints  
The counter cannot be memorized  
or reset when you are using this  
feature.  
(TV programming will appear while the tape is rewinding.)  
Positions A and B will be erased  
when a tape is ejected or when you  
press the REC(ord)/OTR button.  
If the TV/VCR is turned off when  
you are using this feature, the  
TV/VCR will memorize positions A  
and B.  
A-B REPEAT will not appear on-  
screen at step 5 if a tape is not in  
the TV/VCR. NO CASSETTE will  
flash on-screen briefly.  
You cannot rewind or fast forward  
beyond points A or B when you are  
using this feature.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
48 Real Time Counter Memory  
Follow the steps below to reset the real time counter to zero at  
a tape location you want to refer to later.  
1
Play, fast forward or rewind a tape to the location that  
you would like to refer to later. Stop the tape.  
2
Press the STATUS/EXIT button. The real time counter will  
appear on-screen.  
2
5
8
0
3
6
1
4
7
o
1:08 PM  
CH10  
STOP  
9
p
o
+100  
p
o
SLP  
1 : 23 : 45  
PLAY  
5
1
+
REW  
F.FWD  
STOP  
p
3
W hile the counter rem ains on-screen, press the CLEAR  
button to reset the real tim e counter to zero.  
4
2
0 : 00 : 00  
3
4
W hile the counter rem ains on-screen, press the MEMO-  
RY button so that M appears on-screen. To erase a time  
counter memory, press the MEMORY button so that the M disap-  
pears from the screen.  
M 0 : 00 : 00  
5
To return to the previous point at which the real tim e  
counter was reset to zero, when in Stop m ode, press the  
REW (ind)/– button. To return to the future point at  
which the tim e counter was reset to zero, when in Stop  
m ode, press the F.FW D/+ button. W ait for the tape to  
stop, then press the PLAY/button to watch the tape.  
Helpful Hints  
The time counter memory will not  
function during Repeat Play mode.  
Details are on page 45.  
You may only set one time counter  
memory at a time. If you try to set  
the time counter to zero at a sec-  
ond location, the previous time  
counter to zero setting will be lost.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Automatic Operation Features 49  
The following playback features will always operate:  
Autom atic Playback  
When you put a tape in the TV/VCR, the power will come on  
automatically. If the tapes record tab is missing, playback will  
begin. (If a timer recording is set, you may have to press the  
POWER button to turn on the TV/VCR.)  
Autom atic Rewind, Eject, O ff  
When a tape is played, fast forwarded, or recorded to its end, the  
TV/VCR will rewind the tape, stop, turn itself off, then eject the  
tape. If a tape counter memory is set, the TV/VCR will only  
rewind the tape to the point at which the tape counter was set to  
zero, then stop. The TV/VCR will not turn itself off or eject the  
tape.  
Mem ory Rewind, Power O ff  
When the POWER button is pressed while the TV/VCR is rewind-  
ing a tape, REW POWER OFF will appear on-screen. The  
TV/VCR will turn itself off when the tape has finished rewinding.  
If a tape counter memory is set, the TV/VCR may only rewind the  
tape to the point at which the tape counter was set to zero, then  
turn itself off.  
Tape Eject  
A tape can be ejected with the TV/VCR power on or off (but the  
TV/VCR must be plugged in). If a timer recording is programmed,  
a tape can not be ejected when the power is off. Turn on the  
TV/VCR power, then eject the tape. Be sure to insert a tape and  
turn off the TV/VCR power for the timer recording.  
Autom atic Tracking Adjustm ent  
The TV/VCR has automatic tracking, which continually adjusts  
tracking to give you the best possible picture quality. With some  
recordings, however, you may get a better picture using the man-  
ual tracking controls (see below).  
Manual Tracking  
To adjust the tracking manually during tape playback, press the  
CHANNEL Up/Down buttons on the TV/VCR.  
NO TES:  
To return tracking to the position it was in when the TV/VCR was  
shipped from the factory, press the CHANNEL Up/Down buttons on  
the TV/VCR at the same time.  
Tracking is returned to automatic tracking when a tape is inserted,  
or when the STOP/button is pressed to halt playback.  
Before Tracking  
Adjustment  
After Tracking  
Adjustment  
Download from Www.Somanuals.com. All Manuals Search And Download.  
50 Playback Options  
Forward and Reverse Searching (SP/LP/SLP)  
1
When in Play mode, press and release the F.FWD/+ button or the  
REW(ind)/– button. A fast forward or reverse picture search will  
begin.  
2
5
8
0
3
6
1
4
7
2
o
To return to normal playback, press the PLAY/button.  
9
p
o
Super High Speed Searching (LP/SLP)  
+100  
p
o
1
PLAY  
When in Play mode, press the F.FWD/+ button or the  
REW(ind)/– button, then press again. The TV/VCR will now  
search in super high speed.  
+
REW  
F.FWD  
STOP  
p
2
To return to normal playback, press the PLAY/button.  
Viewing a Still Picture  
1
When in Play mode, press the PAUSE/STILL button. A still picture  
(frozen image) will appear on-screen. The noise lines will move  
each time you press the PAUSE/STILL button.  
Helpful Hints  
Still mode will automatically switch  
to Stop mode after five minutes to  
protect the TV/VCR and the tape  
from damage.  
SP/LP/SLP means this feature will  
work with tapes recorded in  
Standard Play, Long Play, or Super  
Long Play. For details about tape  
speed, see page 29.  
2
To release the still picture and return to normal playback, press  
the PLAY/button.  
LP/SLP means this feature will work  
with tapes recorded in Long Play  
and Super Long Play. For details on  
tape speed, see page 29.  
If a still picture vibrates vertically,  
stabilize it by pressing the CHAN-  
NEL (Up/Down) buttons on the  
TV/VCR.  
• During forward and reverse search-  
ing, horizontal noise bars will  
appear on the TV/VCR screen.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications / Glossary 51  
Glossary  
Specifications  
General  
CRT: 13-inch in line gun  
AUDIO Jack: jack located on the front of the  
TV/VCR which is used to record audio from anoth-  
er source.  
Television system: NTSC-M  
Closed caption system: Section 15.119, FCC  
(Federal Communications Commission) Standard  
Video Heads: Two heads  
Tape width: 1/2 inch (12.65 mm)  
Tape speed  
Autom atic Channel Program m ing: process in  
which the TV/VCR scans all available channels and  
places the ones you receive in its memory. Then,  
when you push the CHANNEL (Up/Down) buttons,  
you only scan through channels you receive.  
SP: 33.35 mm/sec.  
LP: 16.67 mm/sec.  
SLP: 11.12 mm/sec.  
Bands: settings that allow you to tune channels.  
Antenna VHF (very high frequency; channels 2  
- 13) and UHF (ultra high frequency; channels 14  
- 69).  
Cable – all standard channels can be received  
without a Cable Box.  
Operating Temperature: 41˚F (5˚C) to 104˚F (40˚C)  
Relative Humidity: 10% to 75%  
Power requirement: AC 120V, 60Hz  
Power consumption: 75W  
Sound output: 1W  
Brightness: adjusting increases or decreases the  
brightness of the color on-screen.  
Dimensions:  
15-13/16" (H) x 15-3/16" (W) x 14-3/4" (D)  
402 mm x 386 mm x 375 mm  
Weight: 27.5 lbs (12.5 kg)  
Color: adjusting pales or brightens the TV/VCR  
color.  
Dubbing: copying a tape using a VCR.  
HQ : high quality; a feature in the TV/VCR circuitry  
which provides enhanced picture detail.  
Tuner Broadcast Channels  
VHF 2-13, UHF 14-69  
Line Input: The channel to which you set your  
TV/VCR during dubbing. The line input channel is  
always channel 00 (A/V IN).  
CATV Channels  
Midband: A – 1  
Superband: J – W  
Hyperband: A-5 – A-1  
Special Channel: 5A  
Ultraband: 37 – 94, 100 – 125  
Mode: a TV/VCR operation.  
O TR: one touch recording; programming a timed  
recording that starts immediately and records for  
30 minutes to eight hours, whichever you specify.  
Picture: adjust to increase or decrease the con-  
trast of the picture on-screen.  
Term inals  
Antenna IN: VHF/UHF 75 ohms unbalanced  
Video IN: RCA connector  
Audio IN: RCA connector  
Earphone: 3.5 mm CES  
Sharpness: adjusting softens or clarifies the picture  
on-screen.  
Tape Speeds: how fast the tape travels during  
playback or a recording.  
SP (standard play) – fastest tape speed (record-  
ing time for a T120 tape is approximately two  
hours); best picture quality.  
LP (long play) – average tape speed (recording  
time for a T120 tape is approximately four  
hours).  
SLP (super long play) – slowest tape speed  
(recording time for a T120 tape is approximately  
six hours).  
Electrical Specifications  
Video input level: 0.5~2.0Vp-p  
Audio input level: -10dBv  
Video S/N ratio  
SP: More than 42dBµ  
Audio S/N ratio  
SP: More than 38dB  
Designs and specifications are subject to change without  
notice and without our legal obligation.  
Tint: adjusting changes the tints of the picture on the  
TV/VCR from purple to green.  
VCR: video cassette recorder.  
VIDEO Jack: jack located on the front of the  
TV/VCR which is used to record video from anoth-  
er source.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
52 Helpful Hints  
If you are having problems with your TV/VCR, check this list of problems and possible solutions before  
requesting service. You may be able to solve the problem yourself.  
Location  
For safe operation and satisfactory performance of your TV/VCR, remember the following:  
Shield it from direct sunlight and keep it away from sources of intense heat.  
• Avoid dusty or humid places.  
• Avoid places with insufficient ventilation. Do not block the ventilation openings at the top and bottom  
of the TV/VCR. Do not place the TV/VCR on a carpet, as this will block the ventilation openings.  
• Avoid locations subject to strong vibrations.  
• Do not place the TV/VCR near strong magnetic fields.  
• Do not move the TV/VCR from a cold place to a hot place, or vice versa.  
Tim e Selection  
12 AM = Midnight  
12 PM = Noon  
Electrical Shock and Fire Hazards  
• Do not handle the power cord with wet hands.  
• Do not pull the power cord when disconnecting the TV/VCR from the AC (alternating current) wall  
outlet. Grasp it by the plug.  
• If water is spilled on the TV/VCR, unplug the power cord immediately and take the TV/VCR to an  
authorized service center.  
• Do not put your fingers or objects into the TV/VCR cassette compartment.  
• Do not place anything on top of the TV/VCR.  
Dew W arning  
Moisture condensation may occur inside the unit when it is moved from a cold place to a warm place,  
after heating a cold room, or when the humidity is high. There is no warning that moisture has accu-  
mulated in your TV/VCR. But, if you try to play a tape in a TV/VCR in which moisture has accumulat-  
ed, the tape and the TV/VCR could be damaged. Therefore, if you try to play a tape and the tape is  
destroyed, and you think moisture may have accumulated inside the TV/VCR, keep the TV/VCR power  
on (but do not play a tape) for at least two hours. This will allow the TV/VCR to dry.  
TV/VCR will not record.  
Make sure the tape has a record tab (page five).  
TV/VCR will not perform a tim er recording.  
Make sure the recording start and stop times are set correctly (pages 32 - 39).  
Make sure the TV/VCR power is off.  
Make sure the clock is set (pages 12 - 17).  
Make sure there is a tape in the TV/VCR. The tape must have a record tab.  
Make sure the power has not failed. The TV/VCR may not perform or continue a timer recording if a  
power interruption of more than one minute occurs before or during the timer recording, even if the  
power comes back on.  
Make sure the TV/VCR is not in Record Defeat mode (page 40).  
TV/VCR will not perform a one touch recording.  
Make sure the tape has a record tab (page five).  
Make sure the TV/VCR is not in Record Defeat mode (page 40).  
• Plug the power cord into an active AC outlet (page seven).  
• Check your hookups (pages six - seven).  
• Program channels (page 10).  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Helpful Hints (contd) 53  
TV/VCR has no power.  
Make sure the power plug is completely connected to an AC (alternating current) outlet.  
A power failure occurred.  
• Follow the steps on page eight to select a language and program channels, if necessary. Then set the  
clock (pages 12 - 17).  
TV/VCR power shuts off after 15 m inutes.  
• To save energy, the TV/VCR will shut itself off after 15 minutes when it is on a channel that is not  
receiving a broadcast signal (for example, a station that has gone off the air for the night). This is normal.  
Channel reception is poor.  
• Check connections, then program channels again (page 10).  
TV/VCR does not have a picture.  
• Adjust the antenna (pages six - seven).  
• Connect the antenna or cable directly to the TV/VCR.  
• Adjust the TV/VCR picture controls (pages 24 - 25).  
TV/VCR has poor sound or no sound.  
• Adjust the volume.  
• Press the MUTE button to restore the volume.  
Tape playback is poor or tape is destroyed.  
• Adjust the tracking. Details are on page 49.  
• If moisture has accumulated in your TV/VCR, keep the power on for at least two hours, but do not try  
to play a tape. Details are on page 52.  
TV/VCR does not display closed captioning.  
• Cancel Counter Only mode. Details are on page 26.  
Make sure closed captioning is available for the program. Refer to the TV listings in your local newspa-  
per.  
Rem ote control does not operate TV/VCR.  
• Aim the remote control directly at the TV/VCR’s remote sensor. Details are on pages five and 20.  
• Remove all obstacles between the remote control and the TV/VCR.  
• Inspect and replace the batteries in the remote control. Details are on page five.  
Num ber buttons wont work for channels above 69.  
Select CABLE from the INPUT section of the pop up menu, then let the TV/VCR program the channels.  
Details are on page 10.  
TV/VCR cant receive channels above 13.  
Select CABLE from the INPUT section of the pop up menu, then let the TV/VCR program the channels.  
Details are on page 10.  
A tape cant be inserted into the TV/VCR.  
• Insert the tape window side up, with the record tab facing you.  
Make sure a tape isnt already in the TV/VCR by pressing the STOP/EJECT button on the TV/VCR.  
• Gently push on the center of the tape. Never force a tape into the TV/VCR.  
A tape cant be rem oved from the TV/VCR.  
Make sure the power plug is completely connected to an AC (alternating current) outlet.  
• If a timer recording is programmed, turn on the TV/VCR power, then eject the tape. Be sure to insert a  
tape and turn off the TV/VCR power for the timer recording.  
TV/VCR ejects the tape when you try to start a recording.  
Make sure the tape has a record tab. Details are on page five.  
The cylinder rotates when the TV/VCR is in Stop m ode.  
• To enable the quick play mechanism, the cylinder will rotate for about five minutes. This is normal.  
Daylight-Saving Tim e  
When Daylight-Saving Time is ON, the clock time will change automatically as follows: on the first  
Sunday of April, from 2 a.m. to 3 a.m.; on the last Sunday of October, from 2 a.m. to 1 a.m.  
When programmed timer recordings start between 2 a.m. and 2:59 a.m. on the first Sunday of April, the  
TV/VCR will start recording at 3 a.m. (summer time).  
When programmed timer recordings end between 2 a.m. and 2:59 a.m. on the first Sunday of April, the  
TV/VCR will stop at 3 a.m.  
When using this feature, a program that occurs during the spring time change may not record complete-  
ly. Adjust the start and stop times accordingly.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
54 Limited Warranty  
TV/VCR COMBINATION  
90 Days Free Labor/One Year Free Parts Exchange (Two Years Free Exchange on Color Picture Tube)  
This product must be carried in for repair.  
WHO IS COVERED?  
tribute the product, the local Philips service organiza-  
You must have proof of purchase to receive warranty tion will attempt to provide service (although there  
service. A sales receipt or other document showing  
that you purchased the product is considered proof  
of purchase.  
may be a delay if the appropriate spare parts and  
technical manual(s) are not readily available).  
MAKE SURE YOU KEEP...  
WHAT IS COVERED?  
Please keep your sales receipt or other document  
showing proof of purchase. Attach it to this owners  
manual and keep both nearby. Also keep the original  
box and packing material in case you need to return  
your product.  
Warranty coverage begins the day you buy your  
product. For 90 days thereafter, all parts will be  
repaired or replaced, and labor is free. From 90 days  
to one year from the day of purchase, all parts will be  
repaired or replaced, but you pay for all labor  
charges. From one to two years from the day of pur-  
chase, you pay for the replacement or repair of all  
parts except the picture tube, and for all labor  
charges. After two years from the day of purchase, you  
pay for the replacement or repair of all parts, and for  
all labor charges.  
BEFORE REQUESTING SERVICE...  
Please check your owners manual before requesting  
service. Adjustments of the controls discussed there  
may save you a service call.  
TO GET WARRANTY SERVICE IN U.S.A., PUER-  
TO RICO OR U.S. VIRGIN ISLANDS...  
Take the product to a Philips factory service center  
(see enclosed list) or authorized service center for  
repair. When the product has been repaired, you  
must pick up the unit at the center. Centers may  
keep defective parts.  
All parts, including repaired and replaced parts, are  
covered only for the original warranty period. When  
the warranty on the product expires, the warranty on  
all replaced and repaired parts also expires.  
WHAT IS EXCLUDED?  
Your warranty does not cover:  
(In U.S.A., Puerto Rico and U.S. Virgin Islands, all  
implied warranties, including implied warranties of  
merchantability and fitness for a particular purpose,  
are limited in duration to the duration of this express  
warranty. But, because some states do not allow limi-  
tations on how long an implied warranty may last, this  
limitation may not apply to you.)  
• labor charges for installation or setup of the prod-  
uct, adjustment of customer controls on the prod-  
uct, and installation or repair of antenna systems  
outside of the product.  
• product repair and/or part replacement because of  
misuse, accident, unauthorized repair or other  
cause not within the control of Philips Consumer  
Electronics Company.  
• reception problems caused by signal conditions or  
cable or antenna systems outside the unit.  
• a product that requires modification or adaptation  
to enable it to operate in any country other than  
the country for which it was designed, manufac-  
tured, approved and/or authorized, or repair of  
products damaged by these modifications.  
• incidental or consequential damages resulting from  
the product. (Some states do not allow the exclu-  
sion of incidental or consequential damages, so the  
above exclusion may not apply to you. This  
includes, but is not limited to, prerecorded materi-  
al, whether copyrighted or not copyrighted.)  
• damage caused by the use of non-VHS tapes or  
tapes that have not been tested and labeled for  
use in two, four, six, and eight hour VHS  
recorders.  
TO GET WARRANTY SERVICE IN CANADA...  
Please contact Philips at:  
1-800-661-6162 (French Speaking)  
1-800-363-7278 (English Speaking)  
(In Canada, this warranty is given in lieu of all other  
warranties. No other warranties are expressed or  
implied, including any implied warranties of mer-  
chantability or fitness for a particular purpose. Philips  
is not liable under any circumstances for any direct,  
indirect, special, incidental or consequential damages,  
howsoever incurred, even if notified of the possibility  
of such damages.)  
REMEMBER...  
Please record below the model and serial numbers  
found on the product. Also, please fill out and mail  
your warranty registration card promptly. It will be  
easier for us to notify you if necessary.  
• a product that is used for commercial or institu-  
tional purposes.  
MODEL # __________________________________  
SERIAL # __________________________________  
WHERE IS SERVICE AVAILABLE?  
Warranty service is available in all countries where  
the product is officially distributed by Philips  
Consumer Electronics Company. In countries where  
Philips Consumer Electronics Company does not dis-  
This warranty gives you specific legal rights. You may have  
other rights which vary from state to state.  
Philips Service Com pany, P.O . Box 555, Jefferson City, Tennessee 37760, (423) 475-8869  
EL4963E003 / MAC 6108/ 1-97  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Index 55  
a-b repeat playback . . . . .46 - 47  
accessories . . . . . . . . . . . . . . .56  
ant(enna) jack . . . . . . . . . . .6, 21  
audio jack . . . . . . . . . . . . . .7, 20  
automatic  
button . . . . . . . . . . . . . . . .23  
real time counter . . . . . . . .48  
rewind, power off . . . . . . .49  
menu button . . . . . . . . . . . . .22  
mute button . . . . . . . . . . . . . .23  
super long play . . . . . . . . .29, 51  
table of contents . . . . . . . . . . .4  
tape  
duplication . . . . . . . . . . . . .31  
speed . . . . . . . . . . . . . .29, 51  
time  
setting . . . . . . . . . . . . .12 - 17  
zone . . . . . . . . . . . . . . . . . .19  
timer recording  
cancelling . . . . . . . . . . . . . .35  
reviewing . . . . . . . . . . . . . .35  
setting . . . . . . . . . . . . .32 - 34  
with vcr plus+ programming  
system . . . . . . . . . . . . . .36-39  
tint, adjusting . . . . . . . . .24 - 25  
tracking . . . . . . . . . . . . . . . . .49  
playback . . . . . . . . . . . . . . .49  
rewind . . . . . . . . . . . . . . . .49  
number buttons . . . . . . . . . . .22  
batteries . . . . . . . . . . . . . . . . . .5  
brightness, adjusting . . . .24 - 25  
on-screen-off mode . . . . . . . .26  
on-screen-on mode . . . . . . . .26  
one touch recording . . . . . . . .30  
cassette (see tape)  
cassette compartment . . . . . .20  
channel  
pause/still button . . . . . . .23, 50  
picture, adjusting . . . . . . .24 - 25  
play button . . . . . . . . . . . .20, 22  
playback options . . . . . . . . . . .50  
playing . . . . . . . . . . . . . . . . . .28  
power  
above 100 . . . . . . . . . . . . .22  
adding . . . . . . . . . . . . . . . .11  
deleting . . . . . . . . . . . . . . .11  
memory . . . . . . . . . . . . . . .10  
programming . . . . . . . . . . .10  
reviewing . . . . . . . . . . . . . .11  
up/down buttons . .20, 23, 49  
clear button . . . . . . . . . . . . . .23  
clock . . . . . . . . . . . . . . . .12 - 17  
closed caption system . . .42 - 43  
color, adjusting . . . . . . . .24 - 25  
connections . . . . . . . . . . . .6 - 7  
contents, table of . . . . . . . . . . .4  
controls  
vcr plus+  
button . . . . . . . . . . . . .20, 22  
cord . . . . . . . . . . . . . . . . . . .7  
button . . . . . . . . . . . . . . . .23  
(setting) . . . . . . . . . . .36 - 37  
timer recording . . . . .38 - 39  
video  
jack . . . . . . . . . . . . . . . .7, 20  
tape (see tape)  
volume bar . . . . . . . . . . . . . . .44  
rear panel . . . . . . . . . . . . . . . .21  
rec/otr button . . . . . . . . .20, 22  
rec(ord) light . . . . . . . . . . . . .20  
record defeat . . . . . . . . . . . . .40  
recording . . . . . . . . . . . . . . . .29  
reminder . . . . . . . . . . . . . . . .27  
remote  
warranty . . . . . . . . . . . . . . . . .54  
remote . . . . . . . . . . . .22 - 23  
tv/vcr . . . . . . . . . . . . .20 - 21  
counter memory . . . . . . . . . .48  
counter only mode . . . . . . . . .26  
control  
buttons . . . . . . . . .22 - 23  
using . . . . . . . . . . . . . . . .5  
sensor . . . . . . . . . . . . . . . .20  
repeat playback . . . . . . . . . . .45  
rerecording . . . . . . . . . . . . . .31  
rew(ind) button . . . . .20, 22, 50  
rewinding . . . . . . . . . . . . . . . .50  
daylight-saving time . . . . . . . .18  
duplication . . . . . . . . . . . . . . .31  
earphone jack . . . . . . . . . . . . .20  
erase protection . . . . . . . . . . . .5  
safety precautions . . . . . . . . . .3  
searching . . . . . . . . . . . . . . . .50  
sensor (remote) . . . . . . . . . . .20  
sharpness, adjusting . . . . .24 - 25  
sleep timer . . . . . . . . . . . . . . .41  
slp . . . . . . . . . . . . . . . . . .29, 51  
smart sound  
fast forward search . . . . . . . . .50  
f.fwd button . . . . . . . .20, 23, 50  
front panel . . . . . . . . . . . . . . .20  
glossary . . . . . . . . . . . . . . . . .51  
button . . . . . . . . . . . . . . . .22  
setting . . . . . . . . . . . . . . . .44  
sp . . . . . . . . . . . . . . . . . .29, 51  
standard play . . . . . . . . . .29, 51  
status display . . . . . . . . . . . . .26  
status/exit button . . . . . . . . . .22  
still picture . . . . . . . . . . . . . . .50  
stop button . . . . . . . . . . . . . .23  
stop/eject button . . . . . . . . . .20  
super high speed searching . . .50  
hookups . . . . . . . . . . . .6 - 7, 31  
helpful hints . . . . . . . . . .52 - 53  
language selection . . . . . . . . . . .9  
line input mode . . . . . .10, 31, 51  
long play . . . . . . . . . . . . . .29, 51  
lp . . . . . . . . . . . . . . . . . .29, 51  
memory  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Check to be sure the items on this page are packed  
with your TV/VCR. These accessories are provided to  
help you use or set up your TV/VCR.  
Rem ote Control (4835 218 37203)  
Two AA Batteries (4835 138 17012)  
If any of these items are not included, or if you need  
to replace an item, contact Philips Service Company  
at the address below.  
Philips Service Company  
P.O. Box 967  
Greeneville, TN 37744-0967  
Or, call 1-800-851-8885.  
IB7852E001  
MAC6192  
Printed In Malaysia  
0EMN01238 / B5813UP * * * * *  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Pelco TV Mount C2230M User Manual
Pentair Universal Remote EZ100 User Manual
Philips Breast Pump ISIS iQ UNO User Manual
Philips Digital Photo Frame 99F2 User Manual
Philips DVR DVDR9000H User Manual
Philips Indoor Furnishings 43199 87 16 User Manual
Philips VCR VR 232 User Manual
Pioneer MP3 Docking Station IDK 80 User Manual
Polycom Server CX300 User Manual
Preference Audio Speaker P 1200 User Manual