C1095M
INSTALLATION MANUAL
ICIDRD INTERFACE CABLE
FOR INTER-CHECK P.O.S. SYSTEMS
®
1.0 SCOPE
6. Refer to Figure 1 or Figure 2 for the proper
wiringconfigurationtoyourInter-Checkunit.
This manual covers the interface for the ICIDRD
interface cable for the Wayne Dresser Plus 1, Plus 2,
and Plus 3 registers.
7. Make sure all connections are tight.
8. Check register and display for proper opera-
tion.
The following should be noted prior to installation:
1. This PELCO P.O.S. interface utilizes the
display port of the Wayne Dresser register.
2.2 INTER-CHECK UNIT PROGRAMMING
1. Enter the MAIN MENUby pressing [ENTER]
WARNING:
in the monitoring mode.
This interface is not a printer
connection. Plugging this interface
into the printer port will damage
the interface.
2. Inter-Check 1000S users press [1] (CHAN-
NEL SETUP).
Inter-Check 2000D users press [1] or [2] de-
pending on the channel you are using for data
display.
2.0 INSTALLATION
3. Press [2] in the CHANNEL MENU (DATA
FORMAT/COMMUNICATION PROTO-
COL).
2.1 LOCATING THE CASH REGISTER
DISPLAY CONNECTION
4. Press [ENTER] or the arrow keys on your
keyboard/keypad until you reach RS232
STANDARD PRINTER.
1. LocatetheportlabeledDISPLAYattherearof
the register.
5. Press [ESC] to save this selection.
2. If the display port is not labeled, follow the
cable from the customer display back to the
register. The connector you need to locate will
be a 9-pin D-SUB variety.
6. Program the Communication Setup values
accordingtoTableI.ConsultyourInter-Check
manual for pertinent programming informa-
tion.
3. After locating this connector, unplug from the
cash register.
7. Press [ESC] to return to monitoring mode and
test for proper operation.
4. Plug PELCO's display interface directly into
the register display port.
5. Plug the register display cable back into the
PELCO interface.
PELCO Manual C1095M — 4/94
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 2. Wiring Configuration for Two (2) Wayne Dresser Registers (Displays)
PELCO Manual C1095M — 4/94
3
Download from Www.Somanuals.com. All Manuals Search And Download.
3.0 WARRANTY AND RETURN
INFORMATION
WARRANTY
RETURNS
Pelco will repair or replace, without charge, any merchandise proved
defectiveinmaterialorworkmanshipforaperiodofoneyearafterthedate
of shipment.
In order to expedite parts returned to the factory for repair or credit, please
call the factory at (800) 289-9100 or (559) 292-1981 to obtain an
authorization number (CA number if returned for credit, and RA number
if returned for repair).
Exceptions to this warranty are as noted below:
All merchandise returned for credit may be subject to a 20% restocking
and refurbishing charge.
Goods returned for repair or credit should be clearly identified with the
assigned CA or RA number and freight should be prepaid. Ship to the
appropriate address below.
•
•
Five years on FT/FR8000 Series fiber optic products.
Three years on Genex® Series products (multiplexers, server, and
keyboard).
Three years on Camclosure® and fixed camera models, except the
CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2,
and MC3651H-2X camera models, which have a five-year warranty.
•
If you are located within the continental U.S., Alaska, Hawaii or Puerto
Rico, send goods to:
Service Department
Pelco
•
•
Two years on standard motorized or fixed focal length lenses.
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and
DF5/DF8 Series fixed dome products.
3500 Pelco Way
Clovis, CA 93612-5699
If you are located outside the continental U.S., Alaska, Hawaii or Puerto
Rico and are instructed to return goods to the USA, you may do one of the
•
•
•
Two years on Spectra®, Esprit®, ExSite™, and PS20 scanners, includ-
ing when used in continuous motion applications.
Two years on Esprit® and WW5700 Series window wiper (excluding
wiper blades).
following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:
Eighteen months on DX Series digital video recorders, NVR300
Series network video recorders, and Endura™ Series distributed
network-based video products.
Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA
•
•
One year (except video heads) on video cassette recorders (VCRs).
Video heads will be covered for a period of six months.
If the goods are to be sent by a FREIGHT FORWARDER, send the goods
to:
Six months on all pan and tilts, scanners or preset lenses used in
continuousmotionapplications(thatis,presetscan,tourandautoscan
modes).
Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: 650-737-1700
Fax: 650-737-0933
Pelco will warrant all replacement parts and repairs for 90 days from the
date of Pelco shipment. All goods requiring warranty repair shall be sent
freight prepaid to Pelco, Clovis, California. Repairs made necessary by
reason of misuse, alteration, normal wear, or accident are not covered
under this warranty.
Pelco assumes no risk and shall be subject to no liability for damages or
loss resulting from the specific use or application made of the Products.
Pelco’s liability for any claim, whether based on breach of contract,
negligence, infringement of any rights of any party or product liability,
relating to the Products shall not exceed the price paid by the Dealer to
Pelco for such Products. In no event will Pelco be liable for any special,
incidental or consequential damages (including loss of use, loss of profit
and claims of third parties) however caused, whether by the negligence
of Pelco or otherwise.
The above warranty provides the Dealer with specific legal rights. The
Dealer may also have additional rights, which are subject to variation from
state to state.
Ifawarrantyrepairisrequired,theDealermustcontactPelcoat(800) 289-
9100 or (559) 292-1981 to obtain a Repair Authorization number (RA),
and provide the following information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice
number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall
under the warranty conditions stated above, please include a written
explanation with the product when returned.
Method of return shipment shall be the same or equal to the method by
which the item was received by Pelco.
PELCO
3500 Pelco Way, Clovis, CA 93612-5699
(559) 292-1981 • (800) 289-9100
FAX (800) 289-9150 or (559) 292-3827
Pelco, the Pelco logo, Camclosure, Esprit,
Genex, Legacy, and Spectra are registered
trademarks of Pelco.
(Product specifications subject to change without
notice.)
Endura and ExSite are trademarks of Pelco.
C1095M
© Copyright 1994, Pelco. All rights reserved.
4
PELCO Manual C1095M — 4/94
Download from Www.Somanuals.com. All Manuals Search And Download.
|