Operating Instructions
Compact Live Switcher
Model No.
AW-HS50N
Before operating this product, please read the instructions carefully and save this manual for future use.
VQTB0000
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety precautions
IMPORTANT SAFETY INSTRUCTIONS
Read these operating instructions carefully before using the unit. Follow the safety instructions on the unit and the
applicable safety instructions listed below. Keep these operating instructions handy for future reference.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
10) Protect the power cord form being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11) Only use attachments/accessories specified by
the manufacturer.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
12) Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the
apparatus. When a cart is used, use
7) Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
caution
when
moving
the
8) Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
cart/apparatus combination to avoid
injury from tip-over.
13) Unplug this apparatus during lightning storms or
when unused for long periods of time.
9) Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding-
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
indicates safety information.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
3. Basic operations................................................. 27
Before use................................................................. 6
Overview ....................................................................................6
Concerning the Operating Instructions ......................................6
Trademarks and registered trademarks .....................................6
Copyrights..................................................................................6
Concerning the ratings display.............................................6
Disclaimer ..................................................................................6
Network-related precautions ......................................................6
3-1. Background transitions......................................................27
3-1-1. Selecting the bus........................................................27
3-1-2. Select the bus using the SHIFT function....................27
3-1-3. Assigning signals to the crosspoint buttons ...............27
3-1-4. Selecting the bus mode..............................................28
3-1-5. Selecting the transition type.......................................28
3-1-6. Manual transitions......................................................28
3-1-7. Auto transition ............................................................29
3-1-8. Cut transition..............................................................29
3-2-1. Selecting the wipe pattern..........................................30
Characteristics.......................................................... 7
Accessories .............................................................. 9
Required personal computer environment ............ 9
Operating precautions ........................................... 10
3-2. Wipe..................................................................................30
3-2-1. Selecting the wipe pattern..........................................30
3-2-2. Selecting the wipe direction .......................................30
3-2-3. Setting the border width and soft effect......................30
3-2-4. Setting the border color..............................................31
3-2-5. Adjusting the border color ..........................................31
3-2-6. Setting the wipe start position....................................31
3-2-7. Registering and recalling the preset memories..........31
1. Parts and their functions ................................... 11
1-1. Control panel.....................................................................11
1-2. Rear panel.........................................................................15
3-3. KEY...................................................................................32
3-3-1. Concerning key combinations....................................32
3-3-2. Setting the PinP and KEY priority ..............................32
3-3-3. Selecting the key materials ........................................33
3-3-4. Key transition..............................................................33
3-3-5. Key setup ...................................................................34
3-3-6. Key adjustments.........................................................36
3-3-7. Chroma key adjustments............................................37
2. Preparations........................................................ 17
2-1. Installation precautions .....................................................17
2-2. Connections with other devices.........................................18
2-2-1. Block diagram.............................................................18
2-2-2. Example of connections.............................................19
2-3. Turning the unit’s power on and off....................................21
2-4. Checking the video output.................................................21
2-4-1. Displaying the OSD menus on a PC monitor .............21
2-4-2. Displaying the OSD menus on an SDI monitor ..........22
3-4. PinP (picture in picture).....................................................39
3-4-1. Selecting the PinP material........................................39
3-4-2. PinP transition............................................................39
3-4-3. PinP settings ..............................................................40
3-4-4. Transition between PinP materials .............................42
3-4-5. Effect dissolve ............................................................43
2-5. OSD (on-screen display) menu operations .......................23
2-5-1. Displaying and clearing the OSD menus ...................23
2-5-2. Moving between the main menu and submenus........24
2-5-3. Operations using the submenus ................................25
3-5. FTB (fade to black)............................................................44
3-6. Internal color signals.........................................................44
3-7. Switching the AUX output..................................................45
3-7-1. Selecting the AUX bus material..................................45
3-7-2. Transitions between AUX materials............................45
3-8. Setting the USER buttons .................................................46
3-9. Frame memories ...............................................................47
3-9-1. Transferring images from the AUX bus.......................47
3-9-2. Saving images in the flash memory ...........................48
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
7. External device control interfaces .................... 68
7-1. LAN connection.................................................................68
7-2. TALLY/GPI.........................................................................68
4. Input/output signal settings............................... 49
4-1. Input signal settings ..........................................................49
4-1-1. Setting the input mode ...............................................50
4-1-2. Setting the material name type ..................................50
4-1-3. Setting the material names ........................................51
4-1-4. Setting the freeze method..........................................51
8. Connections with a computer ........................... 69
8-1. Image transmission functions............................................69
8-2. Connections ......................................................................69
8-3. How to install the software ................................................70
8-4. Basic operations of software.............................................71
4-1-5. Freezing and canceling the freezing of the input
images............................................................................................52
4-1-6. Setting the video process function .............................52
4-1-7. Setting the up-converter.............................................52
4-1-8. Setting the input image scaling ..................................53
4-1-9. Displaying the input image information ......................56
8-5. Image transfer ...................................................................72
8-5-1. Transferring images from the computer to the unit.....72
8-5-2. Transferring the unit’s images to the computer...........73
4-2. Setting the output signals..................................................57
4-2-1. Assigning the output signals ......................................57
4-2-2. Setting the color areas ...............................................57
4-2-3. Setting the DVI-D output signals ................................57
9. Setting menu tables............................................ 76
10. Appearance....................................................... 84
11. Specifications ................................................... 85
Appendix (glossary)............................................... 88
5. Setting the multi view display............................ 59
5-1. Screen layout ....................................................................59
5-2. Setting the split frames and characters.............................60
5-3. Setting the tally displays....................................................60
5-4. Setting the level meters.....................................................61
5-5. Setting the input signal marks...........................................61
6. System settings.................................................. 62
6-1. System menu settings.......................................................62
6-1-1. Setting the video format .............................................62
6-1-2. Setting the ancillary data............................................63
6-1-3. System initialization....................................................64
6-1-4. Network settings.........................................................64
6-2. Operation menu settings...................................................65
6-2-1. OSD (on-screen display) settings...............................65
6-2-2. Other settings.............................................................66
6-2-3. Bus status displays ....................................................67
6-2-4. Version displays..........................................................67
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Before use
ꢀꢁOverview
This unit is a 1 ME digital video switcher which supports a
multiple number of HD and SD formats.
ꢀꢁConcerning the ratings display
The unit’s name, model number and electrical ratings are
indicated on its bottom panel.
Despite its compact size, it comes with four SDI inputs, one
DVI-D input, two SDI outputs and one DVI-D output.
In addition to its background transition capabilities that use
the cut, mix and wipe functions, one keyer channel and one
PinP channel are provided to enable video productions in a
wide variety of forms.
ꢀꢁDisclaimer
Panasonic Corporation will accept absolutely no
responsibility whatsoever when any of the following is
applicable:
Furthermore, using the multi-view display settings, the
screen of a monitor can be split into a number of sections
to accommodate up to ten images, enabling the number of
monitors to be reduced and a space-saving system to be
configured at low cost.
By means of the IP connection, an operating environment
where the unit is tied in with the AW-HE50 HD integrated
camera and AW-RP50 remote camera controller is achieved.
ꢀ Any accidental, special or consequential damages or
harm caused either directly or indirectly in connection
with the unit
ꢁ Any problems with or damage to the unit, etc. resulting
from misuse, abuse or carelessness on the part of the
user
ꢂ When the user has disassembled, repaired or
remodeled the unit
ꢃ Any inconvenience, losses, damages or harm that
result from the disability to display images as a result
of some reason or cause including problems with or
malfunctioning of the unit
ꢀꢁConcerning the Operating
Instructions
ꢄ Any problem caused by any system in which the unit is
used in combination with the equipment of third parties
or any inconvenience, damages or harm occurring as
a result of such
ꢅ Any inconvenience, damages or losses resulting from
accidents caused by an inadequate installation method
or any factors other than a defect in the product itself
ꢆ Any losses of any registered information whatever may
be the cause of those losses
ꢂꢁ For the purposes of these instructions, AW-HS50N is
referred to as “AW-HS50,” AW-RP50N as “AW-RP50,” and
AW-HE50HN and AW-HE50SN as “AW-HE50”.
ꢂꢁ In these instructions, the phrases “pan-tilt head and camera
combination” and “camera integrated with a pan-tilt head”
are both referred to collectively as “remote camera” except
in places where specific equipment is mentioned.
ꢀꢁTrademarks and registered
Any damages, claims, etc. due to loss or leakage of
image data or setting data saved on this unit or in a
personal computer
trademarks
ꢂꢁ Microsoft, Windows, Windows Vista and Internet Explorer
are the registered trademarks or trademarks of Microsoft
Corporation of the United States in the United States,
Japan and other countries.
ꢂꢁ Adobe and Reader are the registered trademarks or
trademarks of Adobe Systems Incorporated in the United
States and other countries.
ꢂꢁ Other names of companies or products appearing in the
text are the registered trademarks or trademarks of the
companies concerned.
ꢀꢁNetwork-related precautions
This unit is connected to a network and used: As such, it
may be susceptible to the following damage, harm or losses.
ꢀ Leakage or release of information via the unit
ꢁ Illegal operation of the unit by third parties with
malicious intent
ꢂ Interference with or shutdown of the unit by third
parties with malicious intent
To prevent these kinds of damage, harm or losses, users
are urged to take the following measures to ensure network
security including, but not limited to, the following:
ꢀꢁCopyrights
It is forbidden to transfer, copy, reverse assemble, reverse
compile or reverse engineer the software included in
this unit or to engage in any act of exportation which
contravenes the applicable export laws and regulations.
ꢂꢁ The unit must be secured on the network by use of
firewalls or other measures.
ꢂꢁ When the unit is to be used in a system to which personal
computers are connected, notification of virus protection
and safe guards against illegal programs are to be
implemented and periodically checked.
ꢂꢁ Unit should be installed in a manner in which its cables
and other accessories cannot be easily damaged.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Characteristics
Compact design
Many different effect functions provided
ꢂꢁ The unit enables the user to select wipe or mix as the
type of background transition.
ꢂꢁ A 1-channel keyer function is provided. The user can
select linear keys, luminance keys or chroma keys as the
key type.
ꢂꢁ The unit features a compact design with its half-rack
size width (210 mm (8-1/4˝)) and its 4RU size (177 mm
(6-15/16˝)) depth.
The AW-RP50 remote camera controller (option) also has
the same size. When it is placed alongside the unit, the
two units are neatly housed in the full rack width.
ꢂꢁ One PinP channel and one AUX bus system are
available.
The user can choose not only cut transitions but also mix
transitions as the effect yielded for switching materials
using the PinP bus and AUX bus. (Bus transition function)
Multiple formats supported
ꢂꢁ The signal formats supported by the unit include
both HD formats (1080/59.94i, 1080/50i, 1080/24Psf,
1080/23.98Psf, 720/59.94p and 720/50p) and SD formats
(480/59.94i and 576/50i).
2-channel frame memory (8 bits)
ꢂꢁ The user can select the still images stored in the frame
memory as the bus material.
Five input systems and three output systems featured
ꢂꢁ The unit comes with four SDI input connectors (SDI IN 1
to SDI IN 4) and one DVI-D input connector (DVI IN).
ꢂꢁ It also comes with two SDI output connectors (SDI OUT 1
and SDI OUT 2) and one DVI-D output connector
(DVI OUT).
ꢂꢁ Still images can be transferred from the host computer,
which is connected to the unit via a LAN, to the frame
memories.
Audio level meter display function
ꢂꢁ This function enables the level of the embedded audio
signals transferred by SDI input to be displayed.
Frame synchronizer system
ꢂꢁ A 10-bit frame synchronizer is incorporated for each of
the SDI inputs so that asynchronous video signals can be
selected with no accompanying shocks.
Straightforward and flexible operability
ꢂꢁ The control panel layout includes a row of five crosspoint
buttons for the A bus and another row of five crosspoint
buttons for the B bus. Using these buttons together with
the SHIFT button enables a total of ten images to be
switched. Cut switches are also made possible by the
CUT button.
ꢂꢁ Separate buttons enable the PinP, KEY and FTB
functions to be turned ON or OFF in a single-step action.
ꢂꢁ The slide lever is not only used to initiate background
transition operations but it can also be allocated to
execute PinP and KEY fade in/out operations.
ꢂꢁ Two USER buttons located on control panel.
Using these buttons together with the SHIFT button
allows a total of four user settings (USER1 to USER4) to
be allocated.
2-channel up-converter, 4-channel Dot by Dot function
and 4-channel video process function
ꢂꢁ An up-converter is incorporated in SDI IN 3 and SDI IN 4.
ꢂꢁ A Dot by Dot function is incorporated for all the SDI input
connectors (SDI IN 1 to SDI IN 4).
By using this function and the PinP function together,
SD materials can be embedded in HD images with no
deterioration in the image quality.
ꢂꢁ The video process function is incorporated in all the
SDI input connectors (SDI IN 1 to SDI IN 4) to make it
possible to adjust the colors at the input stage of the
switcher.
PinP settings or WIPE pattern settings can be allocated
to the USER buttons
Multi view display function
ꢂꢁ One channel is provided for the multi view display
function.
On-screen display (OSD)
The user can select whether the screen is to be split into
10, 9, 6, 5 or 4 sections.
ꢂꢁ On each split screen, the user can assign PGM, PVW,
AUX or other materials in addition to input materials IN1
to IN5.
ꢂꢁ The setting menus can be displayed on an external
monitor from the SDI OUT 2 and DVI OUT output
connectors.
(These menus cannot be displayed using the SDI OUT 1
output connector.)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Characteristics
Function for linkup with a camera integrated with a
pan-tilt head and remote camera controller using IP
connection
ꢂꢁ The unit can be connected to a Panasonic camera
with an integrated pan-tilt head and a remote camera
controller using a network.
By linking it with a remote camera controller, it is possible
to put together a highly efficient operating environment.
Supported camera integrated with a pan-tilt head:
AW-HE50
Supported remote camera controller:
AW-RP50
Only one switcher (the unit) can be linked with a remote
camera controller.
[Display of camera information]
The camera setting information (iris, gain and so on)
obtained by the AW-RP50 can be displayed in the AUX
output or on the split screens of multi view display.
[Transmission of tally information]
The unit’s ON AIR tally information can be sent to the
AW-RP50.
[Switching of materials]
The bus materials of the switcher (the unit) can be
selected from the AW-RP50.
They can be switched in tandem with the selection of
the camera using the AW-RP50.
(Control buses supported: AUX, PVW, PinP, KEY-F)
[Focus assist function]
By operating the buttons on the AW-RP50, it is
possible to switch to the multi view display screen from
the full screen display of the camera images.
(Control bus supported: AUX)
[Control using PAN/TILT lever and ZOOM button]
The PAN/TILT lever and ZOOM button on the
AW-RP50 can be used to change the parameters of
the switcher (the unit).
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
Check that the following accessories are present and accounted for.
Operating Instructions (this manual) ................................... 1
AC adapter ......................................................................... 1
Power cable (2 m [6.6 ft.]) ................................................... 1
CD-ROM (Operating instructions/Image transmission
software) ............................................................................. 1
Required personal computer environment
Run the software that is provided with the switcher on a host computer which satisfies the following specifications.
CPU
Intel® CoreTM2 DUO 2.4 GHz or faster recommended
512 MB or more
Memory
Network function
10Base-T or 100Base-TX
Image display
function
Resolution:
Color generation: True Color (24 bits, 32 bits)
800 ꢃ 600 pixels or more
Supported operating
system
Microsoft® Windows® XP, Microsoft® Windows Vista®, Microsoft®
Windows®
7
Hard disk drive
At least 50 MB of free memory
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating precautions
When the product is to be discarded
Handle carefully.
When the product is to be discarded at the end of its service
life, ask a specialized contractor to dispose of it properly in
order to protect the environment.
Do not drop the product, or subject it to strong shock or
vibration.
Do not carry or move the product by the slide lever lever.
This is important to prevent trouble.
Concerning the consumable parts
ꢂꢁ Cooling fan:
Use the product in an ambient temperature of 0 °C to
40 °C (32 °F to 104 °F).
Avoid using the product at a cold place below 0 °C (32 °F) or
at a hot place above 40 °C (104 °F) because extremely low
or high temperature will adversely affect the parts inside.
This is a consumable part. As a general rule, replace it
every 5 years or so (when the unit has been operated for
15 hours a day).
ꢂꢁ AC adapter:
This is a consumable part. As a general rule, replace it
every 5 years or so (when the unit has been operated for
15 hours a day).
Power off before connecting or disconnecting cables.
Before plugging or unplugging the cables, be sure to switch
power off.
The period when the consumable parts need to be
replaced will differ depending on the operating conditions.
When the time comes to replace one of these parts,
be absolutely sure to ask your dealer to do the job.
Avoid humidity and dust.
Avoid using the product at a humid, dusty place because
much humidity and dust will cause damage to the parts
inside.
Maintenance
Wipe the product using a dry cloth. To remove stubborn
dirt, dip a cloth into a diluted solution of kitchen detergent
(neutral), wring it out well, and wipe the product gently. Then,
after wiping the product with a moist cloth, wipe it again with
a dry cloth.
Caution
ꢂꢁ Avoid using benzine, paint thinners and other volatile
fluids.
ꢂꢁ If a chemical cleaning cloth is to be used, carefully
read through the precautions for its use.
Precaution to be observed during production
This product’s image switching and image effect functions
can be used to produce images which flicker rapidly or
images which change rapidly.
However, bear in mind when using these functions in
production that the kinds of images produced may have an
adverse effect on the viewer’s physical well-being.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Parts and their functions
1-1. Control panel
ꢀ
ꢁ
ꢂ
ꢉ
ꢆ ꢅ
ꢇ
ꢈ
Compact Live Switcher AW-HS50
POWER
AUX
ALARM
LINK
USER 1
3
USER 2
4
SHIFT
OSD/TIME
KEY ON
OSD ON
FTB ON
ꢎ
ꢊ
ꢍ
ꢏ
PinP
KEY-F/S
MIX
TRANSITION TYPE
WIPE
PinP ON
BUS DELEGATION
KEY-S
AUX
A
ꢋ
ꢌ
ꢐ
ꢑ
SHIFT
PGM
PVW
KEY OUT
CLN
MV
5 10
CUT
1
6
2
7
3
8
4
9
KEY-F
PinP
AUX
B
SHIFT
AUTO
BKGD
ꢃ ꢄ
ꢀPOWER indicator [POWER]
ꢉUSER buttons [USER 1, USER 2]
Any four functions selected from among the menu items
can be assigned to the USER 1 button and USER 2
button, and then used.
This indicator lights when the POWER switch (ꢒ) on the
rear panel is set to ON while power is supplied to the DC
IN connector (ꢓ).
The functions registered in [USER1] and [USER3] are
assigned to the USER 1 button whereas the functions
registered in [USER2] and [USER4] are assigned to the
USER 2 button.
While the SHIFT button (ꢅ) is held down, the function
registered in [USER3] or [USER4] can be selected.
Button indicator ON:
ꢁALARM indicator [ALARM]
This indicator lights when the cooling fan (ꢔ) has
stopped running or when there is a problem with the
power supply (voltage drop).
When this occurs, an alarm message appears on the
OSD menu while the OSD menu is displayed on an
external monitor (in the OSD ON status).
The alarm information can be output to an external
device from the unit’s TALLY/GPI connector (ꢕ).
ꢀ For details, refer to “7-2. TALLY/GPI”.
When an alarm has occurred, stop using the unit
immediately, and be absolutely sure to contact your
dealer.
The functions assigned to the USER buttons are
enabled
Button indicator OFF:
The functions assigned to the USER buttons are
disabled
When “[2] WIPE Menu”, “[3] PinP Menu” or “[5] KEY
Adjust Menu” is displayed on the OSD menu or when the
chroma key marker is in the ON status, these buttons
function as short-cut buttons for specific setting items.
ꢀ For details, refer to “3-8. Setting the USER buttons”.
Continuing to use the unit even after an alarm has
occurred could damage the unit.
ꢂLINK indicator [LINK]
This indicator lights when the unit is linked on a network
with the AW-RP50 remote camera controller available as
an option.
The link setting must be enabled at both the unit and
AW-HS50.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Parts and their functions
ꢅSHIFT button [SHIFT]
ꢎPinP ON button [PinP ON]
This is pressed to call the [USER3] and [USER4]
functions which have been assigned to the USER 1
button and USER 2 button or to call the XPT6 to XPT10
materials which have been assigned to crosspoint
buttons [1] to [5].
This is used to combine PinP (picture-in-picture) images
for the transition duration which has been set.
Press the button.
Blinks
Image combining is
now underway.
Button indicator ON:
The SHIFT button is enabled
Button indicator OFF:
The SHIFT button is disabled
(The functions executed using the SHIFT button take
effect only while the button is held down.)
The button indicator
goes off.
Lights
Image combining is
now completed.
Images can no longer
be combined.
Press the button.
Lights
Image combining is
now disabled.
ꢇOSD/TIME dial [OSD/TIME]
By turning the OSD/TIME dial (ꢇ) while keeping the PinP
ON button pressed after the button has been held down,
the transition duration can be changed.
The following operations are performed using this dial.
ꢂ When the main menu is displayed:
Turn the OSD/TIME dial to select a submenu, and
press the dial to enter the selection.
ꢍKEY ON button [KEY ON]
ꢂ When a submenu is displayed:
This is used to combine key materials for the transition
duration which has been set.
Turn the OSD/TIME dial to select a setting item, and
press the dial to enter the selection.
Press the button.
Blinks
When the dial is turned while a setting is blinking, the
setting changes, and when the dial is pressed, the
blinking area moves to the right.
When the dial is held down while a setting is blinking,
the setting is restored to default value.
Image combining is
now underway.
The button indicator
goes off.
Lights
Image combining is
now completed.
Images can no longer
be combined.
(However, the network settings are not returned to
their default values.)
Press the button.
Lights
ꢂ When the dial is turned while it is still held down after
the PinP ON, KEY ON, FTB ON or AUTO button has
been held down, the respective transition duration can
be changed.
Image combining is
now disabled.
By turning the OSD/TIME dial (ꢇ) while keeping the KEY
ON button pressed after the button has been held down,
the transition duration can be changed
ꢈOSD ON button [OSD ON]
This selects whether the OSD menu is to be displayed or
hidden.
ꢊFTB button [FTB ON]
Each time the OSD ON button is held down, the OSD
menu is switched between displayed and hidden.
Button indicator ON:
This initiates fade-in or fade-out with a black screen or a
designated image for the transition duration which has
been set.
The OSD menu is displayed
Button indicator OFF:
The OSD menu is hidden
Button indicator ON:
Now fading out
Button indicator blinking:
Now fading in
Button indicator OFF:
Fade-in or fade-in is now completed
By turning the OSD/TIME dial (ꢇ) while keeping the FTP
ON button pressed after the button has been held down,
the transition duration can be changed.
ꢋCUT button [CUT]
This instantly initiates a transition for the currently
selected operation.
Button indicator ON:
The transition is being executed
Button indicator OFF:
The transition is complete
12
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Parts and their functions
ꢌAUTO button [AUTO]
ꢃBus tally indicators [A, B]
This automatically initiates the transition for the transition
duration which has been set. (Auto transition)
Button indicator ON:
The indicator corresponding to the bus whose program
(PGM) materials are being output lights.
Auto transition is being executed
Button indicator OFF:
Auto transition is complete
ꢏBUS DELEGATION buttons [AUX, PinP, KEY-F/S]
These are used to select the buses which output the
materials selected by the crosspoint buttons (ꢐ, ꢑ).
Any of four lighting statuses are established: the status in
which the indicators of all of the three buttons are off, and
the statuses in which the indicator of one of the buttons
is lighted. (It is not possible for the indicators of two of the
buttons to be lighted at the same time.)
If the AUTO button is pressed while auto transition is
being executed, the auto transition operation is aborted.
When the button is pressed again after the operation was
aborted, the remaining transition is executed.
When the [AUTO] button is pressed with the slide lever
(ꢄ) at a midway setting, the transition is executed in the
remaining time from the midway status.
By turning the OSD/TIME dial (ꢇ) while keeping the MIX
button pressed after the button has been held down, the
transition duration can be changed.
ꢂ When one of the buttons is pressed while the
indicators of all three buttons are off, the indicator of
the pressed button lights.
ꢂ When the button whose indicator is lighted is pressed,
its indicator is turned off.
When a button whose indicator is not lighted is
pressed, only the indicator of the pressed button lights.
ꢄSlide lever
This is used when executing transitions manually.
When the slide lever is moved to the end, the transition is
completed.
The following operations can be undertaken in each of
these statuses.
If it has been moved while an auto transition was being
executed, operation will switch to manual as soon as the
position of the slide lever has gone beyond the amount of
the transition having been executed.
It is possible to select a background, key or PinP using a
menu for materials involving transitions.
1. When the indicators of all three buttons are off:
In this status, the materials of the bus that executes
background transitions are selected.
2. When the indicator of the AUX button is lighted:
In this status, the AUX bus materials are selected.
3. When the indicator of the PinP button is lighted:
In this status, the PinP bus materials are selected.
MIX button [MIX]
4. When the indicator of the KEY-F/S button is
lighted:
This is used to execute transitions (MIX transitions)
while overlapping the images of the A bus and B bus (or
images of the PGM bus and PST bus).
While a transition is being executed, the total of the A bus
and B bus (or PGM bus and PST bus) outputs is held at
100 %.
In this status, the key fill bus and key source bus
materials are selected.
When the MIX button is pressed, its indicator lights to
show that this function is now selected.
If the WIPE button (ꢆ) is now pressed, the function
selection is released, and the indicator goes off.
Button indicator ON:
A MIX transition is being selected
ꢆWIPE button [WIPE]
This is used to execute transitions using the selected
wipe pattern.
When the WIPE button is pressed, its indicator lights to
show that this function is now selected.
If the MIX button ( ) is now pressed, the function
selection is released, and the indicator goes off.
By turning the OSD/TIME dial (ꢇ) after the WIPE button
has been held down and while the button is still pressed,
the wipe pattern can be changed.
Button indicator ON:
Wipe selection underway
13
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Parts and their functions
2. When the indicator of the AUX button is lighted:
When one of the crosspoint buttons is pressed, the
AUX bus material is selected.
ꢐA bus crosspoint buttons [1 to 5]
ꢑB bus crosspoint buttons [1 to 5]
These are used to select the materials to be output to the
AUX bus, PinP bus and KEY-F/S bus.
[B crosspoint buttons]
When a button is pressed and the material allocated to
that button is selected, the indicator of the button lights.
When a button from [1] to [5] is pressed, the material
assigned to the corresponding XPT1 to XPT5 is
selected.
Depending on the status of the BUS DELEGATION
button (ꢏ) indicators, the operation performed differs as
follows.
When a button from [1] to [5] is pressed while the
SHIFT button is held down, the material assigned to
the corresponding XPT6 to XPT10 is selected.
1. While the indicators of all three buttons are off:
When one of the crosspoint buttons is pressed, the
materials of the buses which execute the background
transitions are selected.
[A crosspoint buttons]
When a button from [1] to [5] is pressed, PGM,
PVW, KEY OUT, CLN or MV is selected respectively.
3. While the indicator of the PinP button is lighted:
When a B crosspoint button is pressed, the PinP bus
material is selected.
[B crosspoint buttons]
These are used to select the PST bus materials.
When a button from [1] to [5] is pressed, the material
assigned to the corresponding XPT1 to XPT5 is
selected.
When a button from [1] to [5] is pressed while the
SHIFT button is held down, the material assigned to
the corresponding XPT6 to XPT10 is selected.
[B crosspoint buttons]
When a button from [1] to [5] is pressed, the material
assigned to the corresponding XPT1 to XPT5 is
selected.
When a button from [1] to [5] is pressed while the
SHIFT button is held down, the material assigned to
the corresponding XPT6 to XPT10 is selected.
[A crosspoint buttons]
These are used to select the PGM bus materials.
When a button from [1] to [5] is pressed, the material
assigned to the corresponding XPT1 to XPT5 is
selected.
When a button from [1] to [5] is pressed while the
SHIFT button is held down, the material assigned to
the corresponding XPT6 to XPT10 is selected.
4. While the indicator of the KEY-F/S button is
lighted:
When one of the crosspoint buttons is pressed, the
key fill bus or key source bus material is selected.
[B crosspoint buttons]
These are used to select the key fill bus materials.
When a button from [1] to [5] is pressed, the material
assigned to the corresponding XPT1 to XPT5 is
selected.
When a button from [1] to [5] is pressed while the
SHIFT button is held down, the material assigned to
the corresponding XPT6 to XPT10 is selected.
ꢁ Memo ꢁ
Using the OSD menu, A/B, PGM(A)/PST(B) or PGM(B)/
PST(A) can be selected as the bus mode.
[A crosspoint buttons]
These are used to select the key source bus
The description given above applies when the PGM(A)/
PST(B) has been selected.
materials.
ꢀ For details, refer to “3-1-4. Selecting the bus mode”.
When a button from [1] to [5] is pressed, the material
assigned to the corresponding XPT1 to XPT5 is
selected.
When a button from [1] to [5] is pressed while the
SHIFT button is held down, the material assigned to
the corresponding XPT6 to XPT10 is selected.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Parts and their functions
1-2. Rear panel
ꢔ
ꢙ
ꢗ
ꢖ ꢘ
SIGNAL GND
4
1
3
2
POWER
ON
SDI OUT
SDI IN
ꢒ
ꢓ
1
2
4
3
2
1
12 V IN
LAN
TALLY / GPI
DVI OUT
DVI IN
BOOT
SV NM
ꢕ
ꢜ
ꢛ ꢚ
ꢘSDI IN connectors [SDI IN 1 to 4]
These are the HD/SD SDI signal input connectors.
The following input modes can be set by menu
operations:
ꢒPOWER switch [POWER]
When the POWER switch is set to the ON position,
the POWER indicator (ꢀ) lights, and the unit can be
operated.
SDI IN 1, 2: Normal, DbyD
SDI IN 3, 4: Normal, DbyD, UC, Auto
The video process function can be used for all the SDI IN
1 to 4 input signals.
ꢂ The up-converter cannot be used for SDI IN 1 and 2.
ꢂ When signals differing from the system format have
been input, they are replaced with black signals.
(However, when HD has been selected as the system
format setting and DbyD or UC has been selected
as the input mode setting, SD signals with the same
vertical frequency can be input.)
ꢙSDI OUT connectors [SDI OUT 1, 2]
These are the HD/SD SDI signal output connectors.
The following signals can be assigned to the connector
by menu operations:
PGM, PVW, CLN, AUX, MV, KEYOUT
At the SDI OUT 1 connector, the output signals are split
into two and output through two connectors.
It is the same signal that is output.
ꢂ The OSD menu, multi view display frame, tally
information, names of the materials and audio
level meters are not displayed for the signals of the
SDI OUT 1 connector.
ꢜDVI IN connector [DVI IN]
This is the DVI-D signal input connector.
Signals with the following resolution can be input to this
connector.
ꢂ When the high-resolution multi view mode is enabled,
it is not possible to assign MV signals.
Digital RGB (vertical frequency: 60 Hz):
XGA (1024ꢄ768), WXGA (1280ꢄ768), SXGA (1280ꢄ1024),
WSXGA+ (1680ꢄ1050), UXGA (1600ꢄ1200),
WUXGA (1920ꢄ1200)
Digital RGB:
1920ꢄ1080/50P, 1920ꢄ1080/59.94P
ꢂ Analog signals cannot be input to this connector.
A DVI-I cable cannot be used.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Parts and their functions
DVI OUT connector [DVI OUT]
ꢗGround terminal [SIGNAL GND]
This is the DVI-D signal output connector.
Signals with the following resolution can be output from
this connector by menu operations.
Connect this to the system’s ground.
ꢚSERVICE switch [SV/NM]
This switch is used for maintenance purposes.
For normal operations, select the “NM” position.
Digital RGB (vertical frequency: 60 Hz):
XGA (1024ꢄ768), WXGA (1280ꢄ768), SXGA (1280ꢄ1024),
WSXGA+ (1680ꢄ1050), UXGA (1600ꢄ1200),
WUXGA (1920ꢄ1200)
ꢖWire fastening fitting
An anti-theft wire available on the market can be fastened
to this fitting to prevent theft.
Digital RGB:
1920ꢄ1080/50P, 1920ꢄ1080/59.94P
Furthermore, the following signals can be assigned by
menu operations.
PGM, PVW, CLN, AUX, MV, KEYOUT
The connector supports the high-resolution multi view
mode so that images can be output at a high resolution
when SD has been selected as the system format.
ꢂ Analog signals cannot be output from this connector.
A DVI-I cable cannot be used.
ꢂ When the high-resolution multi view mode has been
enabled, MV signals are assigned to the DVI OUT
connector, and they cannot be assigned to the SDI
OUT 1 connector or SDI OUT 2 connector.
ꢛLAN connector [LAN] (RJ-45)
(10BASE-T/100BASE-TX)
host computer supporting IP connections to this LAN
connector are connected using LAN cables.
When a device is connected directly to the unit, use a
crossover cable (category 5 or above).
When a device is to be connected to the unit through
a hub, for instance, use a straight cable (category 5 or
above).
ꢕTALLY/GPI connector [TALLY/GPI]
(D-sub 15-pin, female, inch thread)
This connector features five contact input ports for
controlling the unit from an external device and seven
open collector output ports for outputting the tally
information and alarm information from the unit.
ꢔCooling fan
ꢓDC IN connector [12V
IN] (DC 12V, 2.5A)
The AC adapter provided with the unit is connected to
this connector.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Preparations
2-1. Installation precautions
ꢅꢁIn addition to heeding the points presented in the “Safety precautions”, observe the
following precautions as well.
Be absolutely sure to ask your dealer to do the jobs of installing and connecting the unit.
Connecting the power supply
ꢂꢁ Use within AC 100 V to 120 V.
ꢂꢁ Be absolutely sure to use only the
power cord and AC adapter supplied
with the panel.
ꢂꢁ Be absolutely sure to connect the
grounding terminal of the power cord
to ground.
ꢂꢁ Be absolutely sure to connect the ground terminal
(SIGNAL GND) at the rear of the unit to the system
ground.
ꢂꢁ Insert the DC plug as far as it will go until it locks into
position.
Handle carefully!
ꢂꢁ Dropping the unit or subjecting it to strong impact or
vibration may cause trouble and/or malfunctioning.
Do not allow any foreign objects to enter inside
the unit!
ꢂꢁ Allowing water, metal items, scraps of food or other
foreign objects inside the unit may cause a fire and/or
electric shocks.
Choosing the best installation location
ꢂꢁ This unit is designed for indoor use only.
ꢂꢁ Install the unit on a sufficiently strong, stable and level
surface for use.
ꢂꢁ Ensure a space of at least 100 mm (3-15/16˝) around the
rear vents to avoid obstructing ventilation.
In particular, ensure sufficient space between ventilation
and wiring when using mounted in a panel or table.
ꢂꢁ Do not install the unit in a cold place where the
temperatures will drop below 0 °C (32 °F) or in a hot
place where the temperatures will rise above 40 °C
(104 °F).
ꢂꢁ When the unit is not going to be used for a prolonged
period of time, turn off its power, and disconnect the
power plug from the AC outlet.
4
3
2
POWER
ON
1
1
SDI IN
2
IN
12V
3
ꢂꢁ Avoid installing the unit where it will be exposed to direct
sunlight or to the hot air that is blown out from other
products.
BOOT
NM
SV
ꢂꢁ Installing the unit in a very humid, dusty or vibration-
prone location may give rise to trouble.
Ventilation holes
17
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Preparations
2-2. Connections with other devices
2-2-1. Block diagram
AW-HS50
DbyD
FS
BLACK
SDI IN 1
SDI IN 2
SDI IN 3
SDI IN 4
SDI OUT 1
BKGD TRANS
VPrc
ꢂ1, ꢂ2
(CUT, MIX, WIPE)
COLOR
BKGD
DbyD
FS
Output 1, 2
(SDI)
COLOR
BAR
VPrc
KEY
Input 1 to 4
(SDI)
(LIN, LUM, CHROMA)
OSD
DbyD
UC
FS
FMEM 1
FMEM 2
SDI OUT 2
OUT
MTX
MV
Frame
VPrc
PinP
FTB
AUX
DbyD
UC
FS
MV
Tally
VPrc
Src
Name
IN
MTX
Output 3
(DVI-D)
DVI OUT
Scaler
Audio
Level
Meter
Input 5
(DVI-D)
DVI IN
Scaler
MULTI VIEW
FS
Power
TALLY/GPI
(D-sub, 15-pin)
LAN
(RJ45)
DC IN
12 V
ꢂ3
[Output, 7 pin]
(1) TALLY OUT 1
(2) TALLY OUT 2
(3) TALLY OUT 3
(4) TALLY OUT 4
(5) TALLY OUT 5
(6) ALARM
[Input, 5 pin]
(10) TALLY DISABLE
(11) AUTO
(12) CUT
(13) KEY ON
(14) PinP ON
Hub
AC adapter
Power cord
AW-RP50
ꢂ4
(7) KEY ON
(15) GND
ꢂ4
AW-HE50
ꢂ4
PC
ꢂ1: At the SDI OUT 1 connector, the output signals are split into two and output through two connectors.
ꢂ2: The setting menus (OSD), multi view display frame, tally information, names of the materials and audio level meters are
not displayed for the signals of the SDI OUT 1 connectors.
ꢂ3: Use a crossover cable when connecting the unit and another device on a 1:1 basis without going through a hub.
ꢂ4: Communication over the internet is not possible.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Preparations
2-2-2. Example of connections
HD SDI
HD camera
HD SDI
ꢂ2
SDI monitor
HD SDI
HD SDI
HD camera
ꢂ2
VTR
HD SDI
HD camera
HD SDI
SD SDI
SDI monitor
SD camera
DVI-D
ꢂ4
DVI-D
PC monitor
ꢂ3
PC
ꢂ1
SIGNAL GND
4
1
3
2
POWER
ON
SDI OUT
SDI IN
1
2
4
3
2
1
12 V IN
LAN
TALLY / GPI
DVI OUT
DVI IN
BOOT
SV NM
AC adapter
Compact Live Switcher
AW-HS50
Power cord
ꢂ1: The up-converter works only with the SDI IN 3 and SDI IN 4 inputs.
(The Dot by Dot mode works with all four SDI IN 1 to 4 inputs.)
ꢂ2: The two signals which are output from the SDI OUT 1 connectors are identical.
The OSD menus, multi view display frame, tally information, names of the materials and audio level meters are not
displayed for the signals of these connectors.
ꢂ3: Analog signal input is not supported.
ꢂ4: Analog signal output is not supported.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Preparations
ꢅꢁExample of IP connections (connecting the unit to the AW-HE50 and AW-RP50)
AW-HE50
AW-HE50
SDI video signal
Monitor 2
Monitor 1
LAN cable
HUB
LAN cable
Monitor
Monitor
AW-HS50
AW-RP50
20
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Preparations
2-3. Turning the unit’s power on and
off
2-4. Checking the video output
Described below are the steps taken to display the unit’s
OSD menu on an external monitor to check the unit’s video
output.
ꢀꢁTurning on the power
2-4-1. Displaying the OSD menus on a PC
monitor
1
Set the POWER switch to the ON position.
When power is supplied to the unit, the POWER
indicator lights up green.
1
Connect the PC monitor to the unit’s DVI OUT
connector.
ꢀꢁTurning off the power
2
3
4
Turn on the power of the PC monitor.
Turn on the power of the unit.
1
Set the POWER switch to the OFF position.
The unit’s power is turned off, and the POWER indicator
goes off.
Hold down the OSD ON button.
The OSD ON button indicator lights, and the OSD
menus are displayed on the PC monitor.
If the OSD menus do not appear on the monitor, refer to
“How to forcibly display the OSD menus”.
Note
If the OSD menu fails to appear on the PC monitor even
after the above steps have been taken, it may mean that
the PC monitor does not support the unit’s DVI output
format.
Check the input specifications of the PC monitor.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Preparations
2-4-2. Displaying the OSD menus on an
SDI monitor
ꢅꢁChanging the video format
If the OSD menus cannot be displayed even when the SDI
monitor has been connected to the unit, the video format
must be changed.
Follow the steps below to change the video format.
If the OSD menus can be displayed using a PC monitor,
change the video format by following the steps in “6-1-1.
Setting the video format”.
1
Connect the SDI monitor to the unit’s
SDI OUT 2 connector.
2
3
4
Turn on the power of the SDI monitor.
Turn on the power of the unit.
1
2
Turn off the power of the unit.
Hold down the OSD ON button.
The OSD ON button indicator lights, and the OSD
menus are displayed on the SDI monitor.
Turn on the unit’s power while at the same time
holding down the button that corresponds to
the video format supported by the SDI monitor.
If the OSD menus do not appear on the monitor, refer to
“How to forcibly display the OSD menus”.
Button to press at the same time
[OSD ON] + A bus crosspoint [1]
[OSD ON] + A bus crosspoint [2]
[OSD ON] + A bus crosspoint [3]
[OSD ON] + A bus crosspoint [4]
[OSD ON] + A bus crosspoint [5]
[OSD ON] + B bus crosspoint [1]
[OSD ON] + B bus crosspoint [2]
[OSD ON] + B bus crosspoint [3]
Video format
1080/59.94i
Notes
1080/50i
ꢂꢁ The OSD menus cannot be output from the
SDI OUT 1 connector.
ꢂꢁ If the OSD menu fails to appear on the SDI monitor
even after the above steps have been taken, it may
mean that the system format which has been set in
the unit is not the correct one.
720/59.94p
720/50p
1080/24psf
1080/23.98psf
480/59.94i
576/50i
Take the steps in the next section to change the unit’s
system format.
ꢀ For details, refer to “Changing the video format”.
3
Hold down the OSD ON button.
The OSD ON button indicator lights, and the OSD
menus are displayed on the SDI monitor.
Note
If the OSD menu fails to appear on the SDI monitor even
after the above steps have been taken, it may mean that
the SDI monitor does not support the unit’s SDI output
format.
Check the input specifications of the SDI monitor.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Preparations
ꢅꢁHow to forcibly display the OSD menus
When the OSD ON button is held down while holding down
the SHIFT button, the following settings are established
automatically.
ꢂꢁ The OSD ON button indicator lights, and the OSD menus
are displayed on the external monitor.
2-5. OSD (on-screen display) menu
operations
The unit’s settings are selected using the OSD menus which
are displayed on the external monitor.
Described here is how to operate the OSD menus.
ꢂꢁ The output destination of the OSD menus is set to both
the SDI OUT 2 connector and DVI OUT connector.
ꢂꢁ The screen size of the OSD menus output from the DVI
OUT connector is set to Auto.
2-5-1. Displaying and clearing the OSD
menus
(The menus are output in the size that corresponds to the
input specifications of the PC monitor which is connected
to the unit.)
ꢅꢁBasic operations
When the OSD ON button is held down, the OSD ON button
indicator lights, and the OSD menus are displayed on the
external monitor.
When the OSD ON button is held down while an OSD menu
is displayed, the OSD ON button indicator goes off, and the
OSD menu display is cleared.
ꢅꢁChanging the connector for outputting
the OSD menus
=ꢁꢆ?ꢀ1RGTCVKQPꢀ/GPW
ꢀꢁꢂ15&ꢀ176
ꢀꢄꢂ15&ꢀ5K\G
5&+ꢃ176ꢄꢅ&8+ꢃ176
(WNN
ꢀꢆꢂ15&ꢀ$CEM
1P
ꢀꢇꢂ-G[ꢀ2TKQTKV[
ꢀꢈꢂ$75ꢀ/QFG
2KP2ꢀQXGTꢀ-';
2)/ꢉ#ꢊꢋ256ꢉ$ꢊ
5GEꢍ(TCOG
$-)&
'PCDNG
'PCDNG
1HH
ꢀꢌꢂ6KOGꢀ7PKV
ꢀꢎꢂ5NKFGꢀ.GXGT
ꢀꢏꢂ)2+ꢀ+PRWV
ꢀꢐꢂ)2+ꢀ1WVRWV
ꢁꢑꢂ%CO%QPVꢀ.KPM
Ť
The OSD menu output connector can be changed using the
“1. OSD OUT” item on the [13] Operation Menu.
SDI-OUT2:
The menus are output from the SDI OUT 2 connector.
DVI-OUT:
The menus are output from the DVI OUT connector.
SDI-OUT2+DVI-OUT:
The menus are output from both the SDI OUT 2
connector and DVI OUT connector.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Preparations
2-5-2. Moving between the main menu and
submenus
ꢅꢁMoving between the main menu and
submenus
The unit’s OSD menus are organized in two hierarchical
levels: the main menu and the submenus.
Moving from the main menu to a submenu
To select a submenu item:
Turn the OSD/TIME dial to select an item.
Entering the setting selected for the submenu item:
Press the OSD/TIME dial to enter the selected item’s
setting.
Main menu:
This lists the submenu items.
Submenu:
This displays the setting items and the settings.
The settings can be changed on this screen.
Moving from a submenu to the main menu
The main menu is restored to the screen when the OSD ON
button is pressed.
#9ꢃ*5ꢈꢑꢀ/CKPꢀ/GPW
Ţ
=ꢀꢁ?ꢀ6+/'ꢋ%$)&ꢀ/GPW
=ꢀꢄ?ꢀ9+2'ꢀ/GPW
=ꢀꢆ?ꢀ2KP2ꢀ/GPW
=ꢀꢇ?ꢀ-';ꢀ5GVWRꢀ/GPW
=ꢀꢈ?ꢀ-';ꢀ#FLWUVꢀ/GPW
=ꢀꢌ?ꢀ%JTQOC-G[ꢀ/GPW
Main menu
Submenu items
=ꢀꢎ?ꢀ/WNVK8KGYꢀ2CVVGTPꢀ/GPW
=ꢀꢏ?ꢀ/WNVK8KGYꢀ1WVꢋ(TCOGꢀ/GPW
=ꢀꢐ?ꢀ:26ꢀ59ꢀ#UUKIPꢀ/GPW
=ꢁꢑ?ꢀ+PRWVꢀ/GPW
Ť
ꢂꢁTurn the OSD/TIME dial, and select the
submenu item.
ꢂꢁPress the OSD/TIME dial to enter the selected
ꢂꢁPress the OSD ON button.
item’s setting.
=ꢁ?ꢀ6+/'ꢋ%$)&ꢀ/GPW
ꢀꢁꢂ#761ꢀ6KOG
ꢀꢀꢀꢀꢀꢁU^ꢀꢀꢀꢀꢀꢑH
ꢀꢀꢀꢀꢀꢁU^ꢀꢀꢀꢀꢀꢑH
ꢀꢀꢀꢀꢀꢁU^ꢀꢀꢀꢀꢀꢑH
ꢀꢀꢀꢀꢀꢁU^ꢀꢀꢀꢀꢀꢑH
ꢀꢄꢂ2KP2ꢀ6KOG
ꢀꢆꢂ-';ꢀ6KOG
ꢀꢇꢂ(6$ꢀ6KOG
Submenu
ꢀꢈꢂ(6$ꢀ5QWTEG
$NCEM
ꢀꢌꢂ#7:ꢀ$75ꢀ6TCPU ꢀꢀꢀꢀꢀꢁU^ꢀꢀꢀꢀꢀꢑH^'PCDNG
ꢀꢎꢂ2KP2ꢀ$75ꢀ6TCPU ꢀꢀꢀꢀꢀꢁU^ꢀꢀꢀꢀꢀꢑH^'PCDNG
ꢀꢏꢂ2KP2ꢀ'((&5.8
ꢀꢐꢂ5GVꢀ%$)&ꢀ%QN
ꢁꢑꢂ#FLꢀ%$)&ꢀ%QN
ꢀꢀꢀꢀꢀꢁU^ꢀꢀꢀꢀꢀꢑH^&KUCDNG
9JKVG
*ꢀꢀꢀꢑꢂꢑ^5ꢀꢀꢀꢑꢂꢑ^.ꢀꢁꢑꢑꢂꢑ
Setting items
Settings
24
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Preparations
2-5-3. Operations using the submenus
1
Selecting the line with the setting item
When the OSD/TIME dial is turned, the cursor “>” at the far left moves up or down.
Bring the cursor to the line with the setting item whose setting is to be changed, and then press the OSD/TIME dial. The cursor
“>” now moves to the center where the setting can be changed.
The value to be set now blinks.
=ꢄ?ꢀ9+2'ꢀ/GPW
=ꢄ?ꢀ9+2'ꢀ/GPW
ꢀꢁꢂ2CVVGTP
ꢁ
ꢀꢁꢂ2CVVGTP
ꢁ
ꢀꢄꢂ&KTGEVKQP
0ꢋ4
ꢀꢄꢂ&KTGEVKQP
0ꢋ4
ꢀꢆꢂ$QTFGTꢋ5QHV
$ꢀꢀꢀꢑꢂꢑ^5ꢀꢀꢀꢑꢂꢑ
ꢀꢆꢂ$QTFGTꢋ5QHV
$ꢀꢀꢀꢑꢂꢑ^5ꢀꢀꢀꢑꢂꢑ
ꢀꢇꢂ5GVꢀ$QTFGTꢀ%QN 9JKVG
ꢀꢇꢂ5GVꢀ$QTFGTꢀ%QN 9JKVG
ꢀꢈꢂ#FLꢀ$QTFGTꢀ%QNꢀ *ꢀꢀꢀꢑꢂꢑ^5ꢀꢀꢀꢑꢂꢑ^.ꢀꢁꢑꢑꢂꢑ
ꢀꢈꢂ#FLꢀ$QTFGTꢀ%QN *ꢀꢀꢀꢑꢂꢑ^5ꢀꢀꢀꢑꢂꢑ^.ꢀꢁꢑꢑꢂꢑ
ꢀꢌꢂ2QUKVKQP
:ꢀꢀꢑꢂꢑꢑ^;ꢀꢀꢑꢂꢑꢑ
ꢀꢌꢂ2QUKVKQP
:ꢀꢀꢑꢂꢑꢑ^;ꢀꢀꢑꢂꢑꢑ
ꢀꢎꢂ5GVꢀ6Qꢀ2TGUGV ꢀꢀꢀꢀꢀꢀꢁ
ꢀꢎꢂ5GVꢀ6Qꢀ2TGUGV ꢀꢀꢀꢀꢀꢀꢁ
Turn the OSD/TIME dial, and
select the item.
Press the OSD/TIME dial to
enter the item.
The value to be set now
blinks.
2
Changing the setting
While the setting is blinking, turn the OSD/TIME dial. The setting in the blinking area now changes.
ꢁ Memo ꢁ
When values are changed for the regular setting items, these changes are reflected straight away but, with some of the
setting items (such as Format), the changes will not be reflected unless the OSD/TIME dial is pressed once the changes
have been made.
An asterisk (ꢃ) appears in front of the currently selected settings to identify these items.
[Returning the setting to its default value]
When the OSD/TIME dial is held down now, the value is returned to its default value.
=ꢄ?ꢀ9+2'ꢀ/GPW
=ꢄ?ꢀ9+2'ꢀ/GPW
ꢀꢁꢂ2CVVGTP
ꢁ
ꢀꢁꢂ2CVVGTP
ꢁ
ꢀꢄꢂ&KTGEVKQP
0ꢋ4
ꢀꢄꢂ&KTGEVKQP
0ꢋ4
ꢀꢆꢂ$QTFGTꢋ5QHV
$ꢀꢀꢀꢑꢂꢑ^5ꢀꢀꢀꢑꢂꢑ
ꢀꢆꢂ$QTFGTꢋ5QHV
$ꢀꢀꢀꢑꢂꢑ^5ꢀꢀꢀꢑꢂꢑ
ꢀꢇꢂ5GVꢀ$QTFGTꢀ%QN 9JKVG
ꢀꢇꢂ5GVꢀ$QTFGTꢀ%QN 9JKVG
ꢀꢈꢂ#FLꢀ$QTFGTꢀ%QN *ꢀꢀꢀꢑꢂꢑ^5ꢀꢀꢀꢑꢂꢑ^.ꢀꢁꢑꢑꢂꢑ
ꢀꢈꢂ#FLꢀ$QTFGTꢀ%QN *ꢀꢀꢀꢑꢂꢄ^5ꢀꢀꢀꢑꢂꢑ^.ꢀꢁꢑꢑꢂꢑ
ꢀꢌꢂ2QUKVKQP
:ꢀꢀꢑꢂꢑꢑ^;ꢀꢀꢑꢂꢑꢑ
ꢀꢌꢂ2QUKVKQP
:ꢀꢀꢑꢂꢑꢑ^;ꢀꢀꢑꢂꢑꢑ
ꢀꢎꢂ5GVꢀ6Qꢀ2TGUGV ꢀꢀꢀꢀꢀꢀꢁ
ꢀꢎꢂ5GVꢀ6Qꢀ2TGUGV ꢀꢀꢀꢀꢀꢀꢁ
This area blinks.
Turn the OSD/TIME dial to change the
setting that is now blinking.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Preparations
3
Moving the blinking area
When a setting item has a multiple number of settings, press the OSD/TIME dial to move the blinking area to the right.
=ꢄ?ꢀ9+2'ꢀ/GPW
=ꢄ?ꢀ9+2'ꢀ/GPW
ꢀꢁꢂ2CVVGTP
ꢁ
ꢀꢁꢂ2CVVGTP
ꢁ
ꢀꢄꢂ&KTGEVKQP
0ꢋ4
ꢀꢄꢂ&KTGEVKQP
0ꢋ4
ꢀꢆꢂ$QTFGTꢋ5QHV
$ꢀꢀꢀꢑꢂꢑ^5ꢀꢀꢀꢑꢂꢑ
ꢀꢆꢂ$QTFGTꢋ5QHV
$ꢀꢀꢀꢑꢂꢑ^5ꢀꢀꢀꢑꢂꢑ
ꢀꢇꢂ5GVꢀ$QTFGTꢀ%QN 9JKVG
ꢀꢇꢂ5GVꢀ$QTFGTꢀ%QN 9JKVG
ꢀꢈꢂ#FLꢀ$QTFGTꢀ%QN *ꢀꢀꢀꢑꢂꢄ^5ꢀꢀꢀꢑꢂꢑ^.ꢀꢁꢑꢑꢂꢑ
ꢀꢈꢂ#FLꢀ$QTFGTꢀ%QN *ꢀꢀꢀꢑꢂꢄ^5ꢀꢀꢀꢑꢂꢑ^.ꢀꢁꢑꢑꢂꢑ
ꢀꢌꢂ2QUKVKQP
:ꢀꢀꢑꢂꢑꢑ^;ꢀꢀꢑꢂꢑꢑ
ꢀꢌꢂ2QUKVKQP
:ꢀꢀꢑꢂꢑꢑ^;ꢀꢀꢑꢂꢑꢑ
ꢀꢎꢂ5GVꢀ6Qꢀ2TGUGV ꢀꢀꢀꢀꢀꢀꢁ
ꢀꢎꢂ5GVꢀ6Qꢀ2TGUGV ꢀꢀꢀꢀꢀꢀꢁ
This area blinks.
Press the OSD/TIME dial.
The blinking area moves to
the right.
4
Completing the changes
When the OSD ON button is pressed while a setting is blinking, the cursor “>” moves to the far left, and the status for selecting
the line with a setting item is restored.
If the item has a multiple number of settings, press the OSD ON button with the blinking area at the far right. The cursor “>” now
moves to the far left, and the status for selecting the line with a setting item is restored.
=ꢄ?ꢀ9+2'ꢀ/GPW
=ꢄ?ꢀ9+2'ꢀ/GPW
ꢀꢁꢂ2CVVGTP
ꢁ
ꢀꢁꢂ2CVVGTP
ꢁ
ꢀꢄꢂ&KTGEVKQP
0ꢋ4
ꢀꢄꢂ&KTGEVKQP
0ꢋ4
ꢀꢆꢂ$QTFGTꢋ5QHV
$ꢀꢀꢀꢑꢂꢑ^5ꢀꢀꢀꢑꢂꢑ
ꢀꢆꢂ$QTFGTꢋ5QHV
$ꢀꢀꢀꢑꢂꢑ^5ꢀꢀꢀꢑꢂꢑ
ꢀꢇꢂ5GVꢀ$QTFGTꢀ%QN 9JKVG
ꢀꢇꢂ5GVꢀ$QTFGTꢀ%QN 9JKVG
ꢀꢈꢂ#FLꢀ$QTFGTꢀ%QN *ꢀꢀꢀꢑꢂꢄ^5ꢀꢀꢀꢑꢂꢑ^.ꢀꢁꢑꢑꢂꢑ
ꢀꢈꢂ#FLꢀ$QTFGTꢀ%QNꢀ *ꢀꢀꢀꢑꢂꢄ^5ꢀꢀꢀꢑꢂꢑ^.ꢀꢁꢑꢑꢂꢑ
ꢀꢌꢂ2QUKVKQP
:ꢀꢀꢑꢂꢑꢑ^;ꢀꢀꢑꢂꢑꢑ
ꢀꢌꢂ2QUKVKQP
:ꢀꢀꢑꢂꢑꢑ^;ꢀꢀꢑꢂꢑꢑ
ꢀꢎꢂ5GVꢀ6Qꢀ2TGUGV ꢀꢀꢀꢀꢀꢀꢁ
ꢀꢎꢂ5GVꢀ6Qꢀ2TGUGV ꢀꢀꢀꢀꢀꢀꢁ
This area blinks.
Press the OSD/TIME dial.
2-5-4. Indications used in these instructions
The operations for the setting items are indicated in these instructions as shown below.
Example: When operating the “5. Adj Border Col” item on the [2] WIPE Menu.
Submenu
Setting item
[2] WIPE Menu
5. Adj Border Col
26
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Basic operations
3-1. Background transitions
3-1-1. Selecting the bus
Press one of the A bus or B bus crosspoint buttons to select
the material for which the background transition is to be
executed.
POWER
AUX
ALARM
PinP
LINK
USER 1
MIX
3
USER 2
WIPE
4
SHIFT
OSD/TIME
KEY ON
OSD ON
FTB ON
KEY-F/S
PinP ON
BUS DELEGATION
TRANSITION TYPE
3-1-2. Select the bus using the SHIFT
function
Crosspoint buttons 6 to 10 can be selected while the SHIFT
button is held down.
When the crosspoint button 6 to 10 materials have been
selected, the SHIFT lamps on the right of the A and B
crosspoint buttons light.
KEY-S
AUX
A
SHIFT
PGM
PVW
KEY OUT
CLN
MV
5 10
CUT
1
6
2
7
3
8
4
9
KEY-F
PinP
AUX
B
SHIFT
AUTO
BKGD
=ꢐ?ꢀ:26ꢀ59ꢀ#UUKIPꢀ/GPW
3-1-3. Assigning signals to the crosspoint
buttons
External video input signals and internally generated signals
can be assigned to crosspoint buttons 1 to 10.
ꢀꢁꢂ:26ꢁ
ꢀꢄꢂ:26ꢄ
ꢀꢆꢂ:26ꢆ
ꢀꢇꢂ:26ꢇ
ꢀꢈꢂ:26ꢈ
ꢀꢌꢂ:26ꢌ
ꢀꢎꢂ:26ꢎ
ꢀꢏꢂ:26ꢏ
ꢀꢐꢂ:26ꢐ
ꢁꢑꢂ:26ꢁꢑ
5&+ꢃ+0ꢁꢉZZZZZZꢊ
5&+ꢃ+0ꢄꢉZZZZZZꢊ
5&+ꢃ+0ꢆꢉZZZZZZꢊ
5&+ꢃ+0ꢇꢉZZZZZZꢊ
&8+ꢃ+0ꢀꢉZZZZZZꢊ
(/'/ꢁ
(/'/ꢄ
%$)&
%$#4
$NCEM
[9] XPT SW Assign Menu
1. XPT1～10. XPT10
The signal assignment statuses are displayed in the “1.
XPT1” to “10. XPT10” items.
The “1. XPT1” to “10. XPT10” items can be set, and the
following materials can be assigned.
Crosspoint button
1 to 10
Name of material
SDI-IN1 to SDI-IN4
DVI-IN
Material
SDI inputs 1 to 4
DVI-D input
FMEM1, FMEM2
CBGD
Frame memory images
Internally generator signal (color background)
Internally generator signal (color bars)
Internally generator signal (black signal)
No signal assigned
CBAR
Black
NoAsign
ꢂꢁ The video signals will not be switched even if a button with the “NoAsign” assigned to it is pressed.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Basic operations
3-1-4. Selecting the bus mode
3-1-5. Selecting the transition type
The bus mode can be set by the following menu operations.
Use the MIX button and WIPE button to select the
background transition mode.
[13] Operation Menu
5. Bus Mode
3-1-6. Manual transitions
A/B bus:
When the slide lever is at side A, the signals selected by
the A bus are output as PGM images.
Operate the slide lever to execute transitions manually.
If the slide lever is moved while an auto transition is
executed, operation will switch to manual as soon as the
position of the slide lever has gone beyond the amount of
the transition which has been executed.
The bus tally indicators on the left of the lever show the
program bus output statuses.
When the slide lever is at side B, the signals selected by
the B bus are output as PGM images.
PGM (A)/PST (B):
Using a flip-flop system, the signals selected by the A
bus are always output as PGM images, and the signals
selected by the B bus are always output as PST images.
PGM (B)/PST (A):
When only indicator A is lighted:
A bus output
When both indicators A and B are lighted:
Transition underway
Using a flip-flop system, the signals selected by the B
bus are always output as PGM images, and the signals
selected by the A bus are always output as PST images.
When only indicator B is lighted:
B bus output
<Setting the slide lever function>
[13] Operation Menu
7. Slide Lever
Any of the following materials for which the transition is to be
executed can be set by operating the slide lever.
BKGD, Key, PinP, NoAsign
28
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Basic operations
3-1-8. Cut transition
When the CUT button is pressed, the background transition
is executed instantly.
ꢂꢁ The auto transition function always targets the
background to execute the transition even if “Key”, “PinP”
or “NoAsign” has been set for manual transition.
3-1-7. Auto transition
When the AUTO button is pressed, the background
transition is executed automatically for the transition duration
which has been set. When it is pressed while the slide lever
is at a midway setting, the transition is executed for the
duration remaining from the midway setting.
The transition duration can be set using the following menu
operation.
[1] TIME/CBGD Menu
1. AUTO Time
When the AUTO button is held down, the time setting is
displayed on the PVW images so the setting can now be
changed while checking what is displayed.
The display unit of TIME/CBGD Menu can be changed using
the following menu operation.
[13] Operation Menu
6.Time Unit
Either seconds or frames can be selected as the display
unit.
Any time from 0 to 999f can be set when using frames
as the display unit. The time that can be set when using
seconds as the display unit differs depending on the video
format.
59.94i: max 33s09f 50p:
59.94p: max 16s39f 24psf:
max 19s49f
max 41s15f
50i:
max 39s24f 23.98psf: max 41s15f
ꢂꢁ The auto transition function always targets the
background to execute the transition even if “Key”, “PinP”
or “NoAsign” has been set for manual transition.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Basic operations
3-2. Wipe
3-2-2. Selecting the wipe direction
Wipe patterns or borders can be set for executing the
background transition.
[2] WIPE Menu
2. Direction
This item is used to select the wipe direction.
N(Normal):
=ꢄ?ꢀ9+2'ꢀ/GPW
Wiping proceeds in the normal direction.
R(Reverse):
ꢀꢁꢂ2CVVGTP
ꢁ
Wiping proceeds in the reverse direction.
N(Normal)/R(Reverse):
ꢀꢄꢂ&KTGEVKQP
ꢀꢆꢂ$QTFGTꢋ5QHV
0ꢋ4
$ꢀꢀꢀꢑꢂꢑ^5ꢀꢀꢀꢑꢂꢑ
ꢀꢇꢂ5GVꢀ$QTFGTꢀ%QN 9JKVG
ꢀꢈꢂ#FLꢀ$QTFGTꢀ%QN *ꢀꢀꢀꢑꢂꢑ^5ꢀꢀꢀꢑꢂꢑ^.ꢀꢁꢑꢑꢂꢑ
The normal direction is replaced with the reverse
direction (or vice versa) when the transition is
completed.
ꢀꢌꢂ2QUKVKQP
:ꢀꢀꢑꢂꢑꢑ^;ꢀꢀꢑꢂꢑꢑ
ꢀꢎꢂ5GVꢀ6Qꢀ2TGUGV ꢀꢀꢀꢀꢀꢀꢁ
N
R
N/R
A
A
A
B
A
B
A
A
B
3-2-1. Selecting the wipe pattern
B
[2] WIPE Menu
1. Pattern
A
The wipe pattern can be selected by turning the OSD/TIME
dial.
B
B
A
B
B
Wipe patterns and their numbers
3-2-3. Setting the border width and soft
effect
1
6
2
7
3
8
4
9
5
[2] WIPE Menu
3. Border/Soft
10
[B: Border]
This is used to set the border width for wiping.
Select “0.0” as the setting if no effects are to be added to the
borders.
11
12
13
[S: Soft]
ꢂꢁ The wipe pattern can also be changed by turning the
OSD/TIME display while pressing the WIPE button
without performing a menu operation.
This is used to set the amount of the soft effects.
This amount indicates the ratio of the soft effect to the
border width.
When only the soft effect is to be added to wipe, set B
(border) to “0.0”.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Basic operations
3-2-4. Setting the border color
3-2-7. Registering and recalling the preset
memories
[2] WIPE Menu
4. Set Border Col
[2] WIPE Menu
7. Set To Preset
This item is used to select any of the following colors for the
borders.
Up to four sets of wipe settings can be registered in the
preset memories.
White, Yellow, Cyan, Green, Magenta, Red, Blue, Black
<Registering the settings in the preset memories>
Select 1, 2, 3 or 4, and press the OSD/TIME dial.
The status currently set is now registered in the selected
preset number.
3-2-5. Adjusting the border color
[2] WIPE Menu
<What can be registered in the preset memories>
ꢂ Wipe patterns
5. Adj Border Col
This item is used to adjust the hue (H), saturation (S)
and luminance (L) of the color which has been set for the
borders.
ꢂ Wipe directions
ꢂ Border width of wipe
ꢂ Soft effect amount
ꢂ Border colors
ꢂ Position at which the transition starts
3-2-6. Setting the wipe start position
<Calling the preset memory settings>
What has been registered in the preset memories can be
called using the USER buttons.
ꢂꢁ To call what has been registered, select “WIPE PRSET”
using the menu operation below.
[2] WIPE Menu
6. Position
This item is used to set the position where the transition is to
start for wipe patterns No.9, 10, 11, 12 and 13 using the X
and Y coordinates.
[12] USER/FMEM Menu
1. USER1
<X-Pos andY-Pos setting range>
Inside screen area
Outside screen area
ꢂꢁ While the [2] WIPE Menu submenu is displayed, the
items to be selected can be switched using the USER
buttons.
USER1: WIPEPos X, USER2: WIPEPos Y,
USER3: —, USER4: —
31
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Basic operations
3-3-2. Setting the PinP and KEY priority
Besides keys, PinP (picture in picture) is also available as
material to be combined with the background image.
3-3. KEY
3-3-1. Concerning key combinations
This operation combines another image with the background
image.
In addition, how the key is to be defined can be adjusted,
and an edge can be added to the image to be combined
with the background.
The display priority of the images (that is, which images are
shown in front of which images) can be changed using the
following menu operation.
[13] Operation Menu
4. Key Priority
How key combinations work is shown in the figure below.
<How key combination works>
PinP over KEY
Background
Background image
HS50
KEY
PinP
Output image
Invert
Key source
KEY over PinP
HS50
Background image
PinP
KEY
Key fill
32
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Basic operations
3-3-3. Selecting the key materials
3-3-4. Key transition
Select the key materials using the A bus and B bus
crosspoint buttons.
When the KEY ON button is pressed, the key transitions
(fades in) for the transition duration which has been set.
<Setting the transition duration>
1
Press the KEY-F/S button to set the crosspoint
buttons to the key bus material selection
mode.
[1] TIME/CBGD Menu
3. KEY Time
ꢂꢁ The transition duration can also be changed by turning
the OSD/TIME dial while pressing the KEY ON button.
When the KEY ON button is held down, the duration
setting is displayed on the OSD menu so the setting can
now be changed while checking what is displayed.
2
3
4
Select the key fill signal using the B bus
crosspoint buttons.
Select the key source signal using the A bus
crosspoint buttons.
The key transition can also be executed by operating the
slide lever.
Press the KEY-F/S button to release the bus
selection mode of the crosspoint buttons.
<Selecting the slide lever operation>
[13] Operation Menu
7. Slide Lever
3
1, 4
AUX
PinP
KEY-F/S
MIX
WIPE
PinP ON
KEY ON
FTB ON
BUS DELEGATION
TRANSITION TYPE
KEY-S
A
AUX
SHIFT
PGM
PVW
KEY OUT
CLN
MV
CUT
1
6
2
7
3
8
4
9
5 10
KEY-F
PinP
B
AUX
SHIFT
AUTO
BKGD
2
33
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Basic operations
With materials with a white background and black
characters, for example, the key level can be reversed and
used by selecting ON for the key invert setting.
3-3-5. Key setup
The key type and other settings can be selected.
<Setting the key invert>
=ꢇ?ꢀ-';ꢀ5GVWRꢀ/GPW
[5] KEY Adjust Menu
4. Invert
ꢀꢁꢂ-G[ꢀ6[RG
ꢀꢄꢂ(KNN
.WOKPCPEGꢉ%JTO1HHꢊ
$WU
ꢀꢆꢂ289
1P
ꢀꢇꢂ5GVꢀ(KNNꢀ%QN
ꢀ ꢀꢈꢂ#FLꢀ(KNNꢀ%QN
ꢀꢌꢂ'FIGꢀ6[RG
ꢀꢎꢂ'FIGꢀ&KTGEVKQP ꢑ
9JKVG
*ꢀꢀꢀꢑꢂꢑ^5ꢀꢀꢀꢑꢂꢑ^.ꢀꢁꢑꢑꢂꢑ
1HH
ꢅꢁFill
[4] KEY Setup Menu
2. Fill
ꢀꢏꢂ'FIGꢀ9KFVJ
ꢄ
ꢀꢐꢂ5GVꢀ'FIGꢀ%QN
ꢁꢑꢂ#FLꢀ'FIGꢀ%QN
$NCEM
*ꢀꢀꢀꢑꢂꢑ^5ꢀꢀꢀꢑꢂꢑ^.ꢀꢀꢀꢑꢂꢑ
This item is used to select the fill type.
Bus:
The bus signal is used for the key fill signal.
ꢅꢁKey Type
Matte:
The internal fill matte is used for the key fill signal.
[4] KEY Setup Menu
1. Key Type
ꢅꢁPVW
This item is used to select the key type.
Luminance (ChrmOff)
[4] KEY Setup Menu
3. PVW
(luminance key/chroma off: Self key):
The key signal is created from the luminance
component of the key fill signal.
This item enables an image with key effects added to be
output for the PVW image to adjust and check the key.
On: An image with key effects added is output for the
PVW image.
Luminance (ChrmOn)
(luminance key/chroma on: Self key):
The key signal is created from the luminance and
chrominance components of the key fill signal.
Linear (linear key: EXT key):
Off: An image with no key effects added is output for the
PVW image.
The key signal is created from the luminance component
of the key source signal. This setting is used when the
key source signal and key fill signal are different.
Chroma (Chroma key: Self key):
ꢅꢁSet Fill Col
[4] KEY Setup Menu
4. Set Fill Col
The key signal is created using a specific hue of the key
fill signal as a reference.
This item is used to select any of the following colors for the
fill matte.
Since the luminance key and chrominance key function as
self keys, the key fill signal is used as the key source signal.
When the luminance key or chrominance key has been
selected as the key type, the key signal remains unchanged
even when the key source signal is switched.
White, Yellow, Cyan, Green, Magenta, Red, Blue, Black
ꢅꢁAdj Fill Col
When the linear key is used, use a material with a black
background and white characters or shapes to be used
for the key combination as the key source signal. The key
combination may not be achieved neatly with materials
having colors other than black and white.
[4] KEY Setup Menu
5. Adj Fill Col
This item is used to adjust the hue (H), saturation (S) and
luminance (L) of the color which has been set for the fill
matte.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Basic operations
ꢅꢁEdge Type
ꢅꢁSet Edge Col
[4] KEY Setup Menu
6. Edge Type
[4] KEY Setup Menu
9. Set Edge Col
This item is used to add borders, shadows or other edges to
the key.
This item is used to select any of the following colors for the
edges.
Off:
White, Yellow, Cyan, Green, Magenta, Red, Blue, Black
An edge is not added.
Border:
A border is added around the entire frame.
Drop:
ꢅꢁAdj Edge Col
A diagonal border is added.
Shadow:
A shadow is added.
Outline:
[4] KEY Setup Menu
10. Adj Edge Col
An outline (only a border with no fill) is added.
This item is used to adjust the hue (H), saturation (S) and
luminance (L) of the color which has been set for the edges.
Border
Shadow
Outline
Drop
ꢅꢁEdge Direction
[4] KEY Setup Menu
7. Edge Direction
This item is used to set the direction (in 45-degree
increments) in which to add “Drop” or “Shadow”.
(Top)
180
135
90
225
270
315
0
(Left)
(Right)
45
(Bottom)
ꢅꢁEdge Width
[4] KEY Setup Menu
8. Edge Width
This item is used to set the edge width.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Basic operations
3-3-6. Key adjustments
ꢅꢁMask
How the key is to be defined can be adjusted.
[5] KEY Adjust Menu
5. Mask
=ꢈ?ꢀ-';ꢀ#FLWUVꢀ/GPW
This item is used to set the masking method.
Off: The key signal is not masked.
ꢁꢂ%NKR
ꢄꢂ)CKP
ꢆꢂ&GPUKV[
ꢇꢂ+PXGTV
ꢀꢀꢀꢀꢑꢂꢑ
ꢀꢀꢁꢑꢑꢂꢑ
ꢀꢀꢁꢑꢑꢂꢑ
1HH
On: The area set using the “6. Mask Adjust1” and “7.
Mask Adjust2” items is masked.
ꢈꢂ/CUM
1HH
ꢅꢁMask Adjust1, Mask Adjust2
ꢌꢂ/CUMꢀ#FLWUVꢁ
ꢎꢂ/CUMꢀ#FLWUVꢄ
ꢏꢂ/CUMꢀ+PXGTV
.ꢀꢃꢄꢈꢂꢑ^4ꢀꢀꢄꢈꢂꢑ
6ꢀꢀꢄꢈꢂꢑ^$ꢀꢃꢄꢈꢂꢑ
1HH
[5] KEY Adjust Menu
6. Mask Adjust1
7. Mask Adjust2
This item is used to set the area to be marked.
6. Mask Adjust1 item:
ꢅꢁClip
This sets the L (left) and R (right) of the area.
7. Mask Adjust2 item:
[5] KEY Adjust Menu
1. Clip
This sets the T (top) and B (bottom) of the area.
This item is used to set the reference level for creating the
luminance key and linear key.
Mask area
The item cannot be used when Chroma (chroma key: self
key) has been selected as the key type.
Key signal valid area
Video signal area
ꢅꢁGain
50
[5] KEY Adjust Menu
2. Gain
TOP (25)
0
BOTTOM (-25)
-50
This item is used to set the amplification level of the
luminance key and linear key.
ꢂꢁ The item cannot be used when Chroma (chroma key: self
key) has been selected as the key type.
(-25)
LEFT
(25)
RIGHT
-50
0
50
ꢂꢁ When [5] KEY Adjust Menu submenu is displayed, the
ꢅꢁDensity
items to be set can be selected using the USER buttons.
USER1: Mask Left, USER2: Mask Right,
USER3: Mask Top, USER4: Mask Bottom
[5] KEY Adjust Menu
3. Density
This item is used to adjust how the luminance key and linear
key are to be defined.
ꢅꢁMask Invert
[5] KEY Adjust Menu
8. Mask Invert
ꢅꢁInvert
[5] KEY Adjust Menu
4. Invert
This item is used to set mask invert.
On: The mask signal is inverted.
Off: The mask signal is not inverted.
This item is used to set key invert.
On: The internally generated key signal is inverted.
Off: The key signal is not inverted.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Basic operations
3-3-7. Chroma key adjustments
How the chroma key is to be defined can be adjusted.
ꢀꢁExecuting the sampling
automatically
By specifying the area where the background is to be
inserted, the chroma components are sampled.
=ꢌ?ꢀ%JTQOC-G[ꢀ/GPW
ꢁꢂ/CTMGT
ꢄꢂ5CORNG
1P
5VCTV
ꢅꢁMaker
ꢆꢂ/CTMGTꢀ2QU
ꢇꢂ/CTMGTꢀ#URGEV
ꢈꢂ4GHꢀ#FLWUV
ꢌꢂ;ꢃ+PHNWGPEG
ꢎꢂ4CFKWU
:ꢀꢀꢑꢂꢑꢑ^;ꢀꢀꢀꢑꢂꢑ^5ꢀꢁꢑꢑꢂꢑ
ꢀꢀꢀꢑꢂꢑꢑ
*ꢀꢀꢀꢑꢂꢑ^5ꢀꢀꢀꢑꢂꢑ^.ꢀꢀꢀꢎꢂꢑ
ꢀꢀꢀꢑꢂꢑꢑ
*ꢀꢁꢑꢑꢂꢑ^5ꢀꢀꢈꢑꢂꢑ
ꢀꢀꢀꢀꢑꢂꢑ
[6] ChromaKey Menu
1. Maker
This item is used to set the sample marker to ON to display
the marker on the PVW image.
ꢏꢂ5QHV
ꢐꢂ%CPEGN
ꢀꢀꢀꢀꢑꢂꢑ
ꢅꢁMarker Pos
Before proceeding with the adjustments, select “Chroma” as
the key type using the menu item below.
[6] ChromaKey Menu
3. Marker Pos
[4] KEY Setup Menu
1. Key Type
This item is used to adjust the X coordinate, Y coordinate
and size of the sample marker.
ꢅꢁSample
As the chroma key, a key signal is created using a specific
hue as a reference.
For instance, the key signal is created by detecting the color
of the background from the image of a person standing in
front of a specific background color, and another background
is combined.
[6] ChromaKey Menu
2. Sample
Press the OSD/TIME dial to sample the hue components of
the area selected by the sample marker.
This unit uses an area system whose area is designated
by a rectangular frame. The result of averaging the colors
of the pixels inside that area is used as the chroma key
reference color (key reference), and the maximum deviation
from the average value is used as the radius of the chroma
key oval.
ꢂꢁ When sampling is completed, the image obtained by
combining the chroma key with the PVW image is output.
(Set the PVW function of the key to ON.)
ꢂꢁ Sampling can be initiated without menu operations by
using the USER buttons and OSD/TIME dial.
Chroma keys faithful to the chroma space sample (area ꢀ
in the figure) can be generated.
USER1: X coordinate, USER2:Y coordinate
USER3: Size, USER4: Aspect ratio
Chroma
Press the target USER button to light the button’s
indicator, and turn the OSD/TIME dial to adjust the
sample marker.
Hue Radius
Hue
When the OSD/TIME dial is pressed, sampling is
initiated.
Sat Radius
ꢀ
Y
Oval-shaped chroma key
37
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Basic operations
ꢅꢁSoft
ꢀꢁOther chroma key settings
[6] ChromaKey Menu
ꢅꢁMarker Aspect
8. Soft
This item is used to adjust the amount of the soft effect on
the boundary of the color to be defined.
[6] ChromaKey Menu
4. Marker Aspect
This item is used to change the aspect ratio of the sample
marker.
ꢅꢁCancel
[6] ChromaKey Menu
9. Cancel
ꢅꢁRef Adjust
This item is used to adjust the amount of color muting.
The color muting is adjusted when the background color is
superimposed over the fill image.
[6] ChromaKey Menu
5. Ref Adjust
This item makes it possible to change the color to be used
as the chroma key reference from the sampled color.
H (Hue):
Hue to be used as the reference
S (Saturation):
ꢁ Memo ꢁ
Knack of adjusting the chroma key
The chroma key adjustments are facilitated by following the
steps below.
Color saturation to be used as the reference
L (Luminance):
Luminance to be used as the reference
ꢂꢁ After auto sampling is finished, the sampled values are
displayed.
ꢀ Initiate automatic sampling, and decide on the color to
be defined.
ꢁ Using the “7. Radius” item, adjust so that the
background color is completely defined.
ꢂ Using the “8. Soft” item, finely adjust the key signal
boundary.
ꢅꢁY-Influence
[6] ChromaKey Menu
6.Y-Influence
This item is used to set the extent of the influence to be
exerted by the Y (luminance) component.
The higher the value set, the greater the influence, and with
a “0” setting, the luminance component has no influence.
ꢅꢁRadius
[6] ChromaKey Menu
7. Radius
This item is used to set the range of the color to be defined.
H (Hue-Radius):
Extent of the range of the hue to be defined
S (Saturation-Radius):
Extent of the range of the color saturation to be
defined
ꢂꢁ After auto sampling is finished, the sampled values are
displayed.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Basic operations
3-4-2. PinP transition
3-4. PinP (picture in picture)
When the PinP button is pressed, the PinP image transitions
(fades in) for the transition duration which has been set.
This function involves combining another image with the
background image.
<Setting the transition duration>
3-4-1. Selecting the PinP material
Select the PinP material using the B bus crosspoint buttons.
[1] TIME/CBGD Menu
2. PinP Time
ꢂꢁ The transition duration can also be changed by turning
the OSD/TIME dial while pressing the PinP button.
When the PinP button is held down, the duration setting
is displayed on the OSD menu. The setting can now be
changed while checking what is displayed.
1
2
3
Press the PinP button to establish the bus
selection mode for the crosspoint buttons.
Select the PinP signal using the B bus
crosspoint buttons.
The PinP transition can also be initiated by operating the
slide lever.
Press the PinP button to release the bus
selection mode for the crosspoint buttons.
<Selecting the slide lever operation>
[13] Operation Menu
7. Slide Lever
1, 3
AUX
PinP
KEY-F/S
MIX
WIPE
PinP ON
KEY ON
FTB ON
BUS DELEGATION
TRANSITION TYPE
KEY-S
A
AUX
SHIFT
PGM
PVW
KEY OUT
CLN
MV
CUT
1
6
2
7
3
8
4
9
5 10
KEY-F
PinP
B
AUX
SHIFT
AUTO
BKGD
2
39
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Basic operations
3-4-3. PinP settings
ꢅꢁBorder Width
Settings can be selected for the PinP images.
[3] PinP Menu
4. Border/Soft
=ꢆ?ꢀ2KP2ꢀ/GPW
[B: Border]
ꢀꢁꢂ5JCRG
ꢀ ꢀꢄꢂ2QUꢒ:ꢋ;ꢋ5K\G
ꢀꢆꢂ289
5SWCTG
:ꢀꢀꢑꢂꢑꢑ^;ꢀꢀꢀꢑꢂꢑ^5ꢀꢁꢑꢑꢂꢑ
1P
This is used to set the width of the PinP image border.
ꢂꢁ Set “0.0” when the border effect is not going to be added.
ꢀꢇꢂ$QTFGTꢋ5QHV
ꢀꢈꢂ5GVꢀ$QTFGTꢀ%QN 9JKVG
$ꢀꢀꢀꢑꢂꢑ^5ꢀꢀꢀꢑꢂꢑ
[S: Soft]
This is used to set the amount of the PinP image’s soft
effect.
ꢀꢌꢂ#FLꢀ$QTFGTꢀ%QN *ꢀꢀꢀꢑꢂꢑ^5ꢀꢀꢀꢑꢂꢑ^.ꢀꢁꢑꢑꢂꢑ
ꢀꢎꢂ6TKOꢀ#FLWUVꢁ
ꢀꢏꢂ6TKOꢀ#FLWUVꢄ
1HHųꢀꢀ^.ꢀꢃꢇꢑꢂꢑ^6ꢀꢀꢇꢑꢂꢑ
4ꢀꢀꢇꢑꢂꢑ^$ꢀꢃꢇꢑꢂꢑ
ꢅꢁSet Border Col
ꢀꢐꢂ5GVꢀ6Qꢀ2TGUGV ꢀꢀꢀꢀꢀꢀꢁ
[3] PinP Menu
5. Set Border Col
ꢅꢁShape
This item is used to select any of the following colors for the
borders of the PinP image.
[3] PinP Menu
1. Shape
White, Yellow, Cyan, Green, Magenta, Red, Blue, Black
This item enables any of the following shapes to be selected
when combining the PinP image.
ꢅꢁAdj Border Col
Square, Circle, Heart, Flower, Star
[3] PinP Menu
6. Adj Border Col
ꢅꢁPos:X/Y/Size
This item is used to adjust the hue (H), saturation (S)
and luminance (L) of the color which has been set for the
borders of the PinP image.
[3] PinP Menu
2. Poas:X/Y/Size
This item is used to adjust the position (X, Y) and size (S) of
the PinP image.
ꢂꢁ The items to be set can be selected using the USER
buttons when the [3] PinP Menu submenu is displayed.
USER1: PinP X, USER2: PinP Y,
USER3: PinP Size, USER4: —
Press the target USER button to light the button’s
indicator, and turn the OSD/TIME dial to adjust the PinP
image.
Note
The size of the image cannot be changed when the
Dot by Dot mode has been set for the PinP material.
ꢅꢁPVW
[3] PinP Menu
3. PVW
This item makes it possible to establish the setting for
outputting the PinP image to the PVW image.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Basic operations
ꢅꢁTrim Adjust1,Trim Adjust2
ꢅꢁSet To Preset
[3] PinP Menu
7.Trim Adjust1
8.Trim Adjust2
[3] PinP Menu
9. Set To Preset
Up to four sets of PinP image settings can be registered in
the preset memories.
The method of trimming the PinP image and the area to
be trimmed are set using the “7. Trim Adjust1” and “8. Trim
Adjust2” items.
<Registering the settings in the preset memories>
Select 1, 2, 3 or 4, and press the OSD/TIME dial.
The status currently set is now registered in the selected
preset number.
7.Trim Adjust1 item:
Off:
The image is not trimmed.
4:3:
The image is automatically trimmed so that its aspect
ratio is 4:3.
Manual:
<What can be registered in the preset memories>
ꢂ Shape used when combining the images
ꢂ Image position (X, Y)
ꢂ Image size
ꢂ Border width
The image is trimmed in the area which has been set
ꢂ Border color
using the “8. Trim Adjust1” and “9. Trim Adjust2” items.
ꢂ Soft effect amount
ꢂ Trimming setting
8.Trim Adjust2 item:
This is used to set the T (top) and B (bottom) of the
trimming area.
<Calling the preset memory settings>
What has been registered in the preset memories can be
called using the USER buttons.
ꢂꢁ To call what has been registered, select “PinP PRSET”
using the menu operation below.
Trimming area
PinP valid area
PinP original size
[12] USER/FMEM Menu
1. USER1
50
TOP (40)
0
BOTTOM (-40)
-50
-50
(-40)
0
50
(40)
LEFT
RIGHT
41
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Basic operations
3-4-4. Transition between PinP materials
By switching between the PinP bus crosspoint buttons, the
MIX transition can be executed from one PinP material to
another PinP material for the transition duration which has
been set.
ꢂꢁ When one material set to the Dot by Dot mode and
another material have been switched, cut switching where
the images change in an instant is performed.
<Setting the transition duration>
[1] TIME/CBGD Menu
7. PinP BUS Trans
While the transition is underway, the indicator of the
transition source button lights, and the indicator of the
transition destination button blinks.
When the transition is completed, the indicator of the
transition source button goes off, and the indicator of the
transition destination button lights.
When another signal has been selected while a transition is
underway, the processing for the transition will continue from
the interim point.
This operation can also be enabled or disabled using this
menu item.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Basic operations
<Selecting the Dot by Dot mode>
3-4-5. Effect dissolve
If an SD format image is used as the PinP material when
the system is operating in an HD mode, images can be
combined in the Dot by Dot mode (actual size images).
In this mode, the SD format images are not up-converted so
image deterioration can be prevented.
This function enables one effect to be switched to another
smoothly when the data in the preset memory where the
PinP image settings were registered is called using the
USER buttons.
ꢂꢁ Before using the function, set the transition duration and
either enable or disable for effect dissolve using the menu
below.
[10] Input Menu
1. Mode
Normal:
[1] TIME/CBGD Menu
8. PinP EFFDSLV
The input signals in conformity with the system format
are enabled.
DbyD:
The images are combined in the Dot by Dot mode
(actual size images).
<Items covered by effect dissolve>
ꢂ Image position (X, Y)
ꢂ Image size
ꢂ Border width
ꢂ Border color
SD
HD
ꢂ Soft effect amount
ꢂ Trimming setting
SD
PinP material
PinP combined images
43
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Basic operations
3-5. FTB (fade to black)
3-6. Internal color signals
Pressing the FTB ON button initiates fade-out from the
program image to a black screen or fade-in from a black
screen to the program image for the transition duration
which has been set.
These signals allow the color of the background used by the
bus to be set.
ꢅꢁCBGD Color
[1] TIME/CBGD Menu
9. Set CBGD Col
<Setting the transition duration>
[1] TIME/CBGD Menu
4. FTB Time
Any of the following colors can be selected for the
background image.
White, Yellow, Cyan, Green, Magenta, Red, Blue, Black
<Selecting the image>
[1] TIME/CBGD Menu
5. FTB Source
ꢅꢁColor Adjust
Any of the following images in place of a black screen can
be selected.
[1] TIME/CBGD Menu
10. Adj CBGD Col
FMEM1, FMEM2, CBGD, White
This item is used to adjust the hue (H), saturation (S)
and luminance (L) of the color which has been set for the
background image.
ꢂꢁ The transition duration can also be changed by turning
the OSD/TIME dial while pressing the FTB ON button.
When the FTB ON button is held down, the duration
setting is displayed on the OSD menu so the setting can
now be changed while checking what is displayed.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Basic operations
3-7-2. Transitions between AUX materials
3-7. Switching the AUX output
By switching between the AUX bus crosspoint buttons, the
MIX transition can be executed from one AUX material to
another AUX material for the transition duration which has
been set.
3-7-1. Selecting the AUX bus material
The AUX output material is selected using the A bus and B
bus crosspoint buttons.
<Setting the transition duration>
[1] TIME/CBGD Menu
1
2
Press the AUX button to set the crosspoint
buttons to the AUX bus material selection
mode.
6. AUX BUS Trans
While the transition is underway, the indicator of the
transition source button lights, and the indicator of the
transition destination button blinks.
When the transition is completed, the indicator of the
transition source button goes off, and the indicator of the
transition destination button lights.
When another signal has been selected while a transition is
underway, the processing for the transition will continue from
the interim point.
Select the material using the B bus crosspoint
buttons.
When the buttons from [1] to [5] are pressed, the
materials assigned to the corresponding XPT1 to XPT5
are selected.
When the button from [1] to [5] are pressed while the
SHIFT button is held down, the materials assigned to
the corresponding XPT6 to XPT10 are selected.
3
4
Select the output signal using the A bus
crosspoint buttons.
When buttons [1], [2], [3], [4] and [5] are pressed, PGM,
PVW, KEY OUT, CLN or MV are selected, respectively.
This operation can also be enabled or disabled using this
menu item.
Press the AUX button to release the bus
selection mode for the crosspoint buttons.
1, 4
3
AUX
PinP
KEY-F/S
MIX
WIPE
PinP ON
KEY ON
FTB ON
BUS DELEGATION
TRANSITION TYPE
KEY-S
A
AUX
SHIFT
PGM
PVW
KEY OUT
CLN
MV
CUT
1
6
2
7
3
8
4
9
5 10
KEY-F
PinP
B
AUX
SHIFT
AUTO
BKGD
2
45
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Basic operations
3-8. Setting the USER buttons
Menu item functions can be assigned to the USER 1[3]
button and USER 2[4] button for use later.
Up to four functions can be assigned from USER1 to
USER4.
The functions registered in [USER1] and [USER3] are
assigned to the USER 1 button, and the functions registered
in [USER2] and [USER4] are assigned to the USER 2
button.
While the SHIFT button is pressed, the function registered in
[USER3] or [USER4] can be selected.
The button indicator is lighted when the functions assigned
to the button are enabled, and it is off when the functions
are disabled.
=ꢁꢄ?ꢀ75'4ꢋ(/'/ꢀ/GPW
ꢁꢂ75'4ꢁ
ꢄꢂ75'4ꢄ
ꢆꢂ75'4ꢆ
2KP2ꢀ2TGUGV
ꢃ
Each time a USER button is pressed, its functions are
switched between enabled and disabled.
ꢃ
ꢃ
ꢇꢂ75'4ꢇ
ꢈꢂ(/'/ꢀ5'.'%6
ꢌꢂ#7:ꢀ6Qꢀ(/'/
ꢎꢂ(/'/ꢀ/QFG
(/'/ꢁ
4Xꢒ1HHꢀ^':ꢒ10
/ꢒ#761ꢀ^':ꢒ10
The following functions can be assigned to the USER buttons (USER 1 and USER 2).
No.
Item
PinP Preset
Function
1
2
This item can be set in the [USER1] only.
When it is set, [USER1] to [USER4] can all be used for registering the data in the PinP preset
memories and calling it from the memories.
WIPE Preset
This item can be set in the [USER1] only.
This item can be set in [USER1] only.
When it is set, [USER1] to [USER4] can all be used for registering the data in the WIPE preset
memories and calling it from the memories.
3
PinPPVW
The PinP image is output to the PVW image.
KEY is output to the PVW image.
4
KeyPVW
5
GPI Input
The GPI input is enabled or disabled.
6
GPI Output
CamCont Link
AUX Transition
PinP Transition
EFFDSLV Time
StrFMEM1
StrFMEM2
No Asign
The GPI output is enabled or disabled.
7
Link control with the AW-RP50 is set to ON or OFF.
The AUX transitions are enabled or disabled.
The PinP transitions are enabled or disabled.
Effect dissolve is enabled or disabled.
8
9
10
11
12
13
The images of the AUX bus are imported into the frame memory (FMEM1).
The images of the AUX bus are imported into the frame memory (FMEM2).
No item assigned
Even when functions have been assigned to the USER buttons, the assigned function will be disabled and the image setting
operations will take priority in the following situations.
<Displaying the chroma key markers>
<Displaying the [3] PinP Menu submenu>
USER1: X, USER2:Y,
USER3: Size, USER4: Aspect
USER1: PinP X, USER2: PinP Y,
USER3: PinP Size, USER4: —
<Displaying the [2] WIPE Menu submenu>
<Displaying the [5] KEY Adjust Menu submenu>
USER1: WIPEPos X, USER2: WIPEPos Y,
USER3: —, USER4: —
USER1: Mask Left, USER2: Mask Right,
USER3: Mask Top, USER4: Mask Bottom
46
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Basic operations
3-9. Frame memories
Still images can be stored in the unit’s two internal frame
memories for use later.
The still images are transferred to the frame memories from
the AUX bus or computer.
ꢂꢁ For details on the function for transferring images to
and from a computer, refer to “8. Connections with a
computer”.
The images in the frame memories can be used as bus
images by assigning FMEM1 and FMEM2 in the crosspoint
buttons.
ꢀ For details, refer to “3-1-3. Assigning signals to the
crosspoint buttons”.
In addition, the frame memory images can be used instead
of the black screen with the FTB (fade to black) function.
The data for the images stored in the frame memories can
be retained even when the power is turned off by saving it in
the flash memory area which is incorporated inside the unit.
3-9-1. Transferring images from the AUX
bus
The frame memory settings can be selected.
[12] USER/FMEM Menu
6. AUX to FMEM
=ꢁꢄ?ꢀ75'4ꢋ(/'/ꢀ/GPW
Rv (Review):
This setting determines whether the review display is
shown.
ꢁꢂ75'4ꢁ
ꢄꢂ75'4ꢄ
ꢆꢂ75'4ꢆ
ꢇꢂ75'4ꢇ
ꢈꢂ(/'/ꢀ5'.'%6
ꢌꢂ#7:ꢀ6Qꢀ(/'/
ꢎꢂ(/'/ꢀ/QFG
2KP2ꢀ2TGUGV
2KP2ꢀ2TGUGV
2KP2ꢀ2TGUGV
2KP2ꢀ2TGUGV
(/'/ꢁ
On: After an image has been imported, the image in
the frame memory (FMEM1 or FMEM2) selected
for the AUX bus is displayed for about 2 seconds.
Even when the review display appears, the next
image can be imported.
4Xꢒ1HHꢀ^':ꢒ10
/ꢒ#761ꢀ^':ꢒ10
Off: The review display is not shown.
Ex (Exec):
When the OSD/TIME dial is pressed, still images are
imported into the frame memory.
[12] USER/FMEM Menu
5. FMEM Select
Select FMEM1 or FMEM2 as the number of the frame
memory in which to store the images.
Review display
PGM
PGM
AUX
AUX
PGM
PGM
AUX
AUX
INPUT1
INPUT5
INPUT2
INPUT6
INPUT3
INPUT4
INPUT1
INPUT5
INPUT2
INPUT6
INPUT3
FMEM1
INPUT4
FMEM1
FMEM1
FMEM2
FMEM2
FMEM2
FMEM2
Imported still image
ꢂꢁ Even when MV (multi view display) is selected by the
AUX bus, the following information is not stored in the
frame memory.
Multi view display frame, names of the materials, tally
information, audio level meter
47
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Basic operations
3-9-2. Saving images in the flash memory
The data of the images stored in the frame memories can be
retained even when the unit’s power is turned off by saving
it in the flash memory area which is incorporated inside the
unit.
Whether to automatically save the image data stored in the
frame memories or save it manually is set when the data is
to be transferred from the AUX bus.
[12] USER/FMEM Menu
7. FMEM Mode
M (Mode):
This is used to set the method of storing the image data
in the flash memory area.
Auto:
The images are stored automatically.
Manual: The images are stored manually.
Ex (Exec):
This is for importing the still images into the flash memory
area.
When the OSD/TIME dial is pressed, the image data in
the frame memory is stored in the flash memory area.
ꢂ This takes effect when “Manual” has been selecting as
the M (Mode) setting.
Note
ꢂꢁ When data is being written in the flash memory area,
a “now writing” message is displayed on the PVW
images.
Do not turn off the power while this message is
displayed.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Input/output signal settings
The display is switched to a menu display such as the one
4-1. Input signal settings
The SDI IN 1 to SDI IN 4 connectors are the SDI signal input
connectors, and the DVI IN connector is the DVI-D signal
input connector.
The 10-bit frame synchronizer function is enabled for all the
SDI input signals.
Using the frame synchronizer function, it is possible to
switch smoothly between non-synchronized video signals.
shown below by the input signals selected.
The menu title changes to “Input Menu/Input Connectors
(Material Names)”.
The settings selected using the “4. Name Type” and
“5. Name” items described below are displayed in the
“(Material Names)” area.
A blank is displayed if a material name has not yet been set.
SDI-IN1, SDI-IN2:
<List of settings by input signal>
Setting menu items and
=ꢁꢑꢂꢁ?ꢀ+PRWVꢀ/GPWꢋ5&+ꢃ+0ꢁꢉꢀꢀꢃꢃꢃꢃꢀꢀꢀꢀꢊ
ꢀꢁꢂ/QFG
0QTOCNĄ
sections in this manual
Input
connector
ꢀꢄꢂ(TGG\Gꢀ5GNGEV (TCOG
Name
Type
Freeze
Select
MODE
4.1.1
ꢄ
Name
4.1.3
ꢄ
Freeze
4.1.5
ꢄ
ꢀꢆꢂ(TGG\G
ꢀꢇꢂ0COGꢀ6[RG
ꢀꢈꢂ0COG
1HHĄ
&GHCWNV
ꢃꢀꢃꢀꢃꢀꢃꢀꢃꢀꢃ
4.1.2
4.1.4
SDI IN 1,
SDI IN 2
ꢀꢌꢂ82TEꢋ;)CKPꢋ2GF 1HHꢀꢀꢀꢀ^;ꢀꢁꢑꢑꢂꢑ^2ꢀꢀꢑꢂꢑ
ꢀꢎꢂ82TEꢒ%)CKPꢋ*WG %ꢀꢁꢑꢑꢂꢑ^*ꢀꢀꢀꢑꢂꢑ
ꢄ
ꢄ
SDI IN 3,
SDI IN 4
ꢄ
ꢄ
ꢄ
ꢄ
ꢄ
ꢄ
ꢄ
ꢄ
DVI IN
—
—
Setting menu items and
sections in this manual
SDI-IN3, SDI-IN4:
=ꢁꢑꢂꢆ?ꢀ+PRWVꢀ/GPWꢋ5&+ꢃ+0ꢆꢉꢀꢀꢃꢃꢃꢃꢀꢀꢀꢀꢊ
Input
DVIIn
information
display
DVIIn
connector Video Proc UpConv
scaling
4.1.8
—
ꢀꢁꢂ/QFG
ꢓ0QTOCN
ꢀꢄꢂ(TGG\Gꢀ5GNGEV (TCOG
4.1.6
4.1.7
—
4.1.9
ꢀꢆꢂ(TGG\G
ꢀꢇꢂ0COGꢀ6[RG
ꢀꢈꢂ0COG
1HHĄ
ꢓ&GHCWNV
+0276ꢆ
SDI IN 1,
SDI IN 2
ꢄ
—
SDI IN 3,
SDI IN 4
ꢄ
ꢄ
—
—
ꢀꢌꢂ82TEꢋ;)CKPꢋ2GF 1HHꢀꢀꢀꢀ^;ꢀꢁꢑꢑꢂꢑ^2ꢀꢀꢑꢂꢑ
ꢀꢎꢂ82TEꢒ%)CKPꢋ*WG %ꢀꢁꢑꢑꢂꢑ^*ꢀꢀꢀꢑꢂꢑ
ꢀꢏꢂ7%ꢒ5ECNGꢋ'%2QU 5ꢀ53ꢀꢀꢀ^'ꢀ%GPVGT
DVI IN
—
—
ꢄ
ꢄ
ꢀꢐꢂ7%ꢒ5K\G
ꢁꢑꢂ7%ꢒ/QXFGV
5ꢀꢁꢑꢑꢂꢑ
ꢆ
ꢄ: Can be set; —: cannot be set
To set the input signals, display the [10] Input Menu using
the OSD menu, and select the input signals.
DVI-IN:
=ꢁꢑꢂꢈ?ꢀ+PRWVꢀ/GPWꢋ&8+ꢃ+0ꢉꢀꢀꢃꢃꢃꢃꢀꢀꢀꢀꢊ
=ꢁꢑ?ꢀ+PRWVꢀ/GPW
ꢀꢁꢂ(TGG\G
ꢀꢄꢂ0COGꢀ6[RG
ꢀꢆꢂ0COG
ꢀꢇꢂ5ECNG
ꢀꢈꢂ5K\G
ꢀ ꢀꢌꢂ*ꢃ(TGS
ꢀꢎꢂ8ꢃ(TGS
ꢀꢏꢂ&QVꢀ%NQEM
1HH
ꢓ&GHCWNV
+0276ꢈ
(KVꢃ8
ꢃ
ꢃ
ꢃ
ꢃ
ꢁꢂ5&+ꢃ+0ꢁꢉZZZZZZꢊ
ꢄꢂ5&+ꢃ+0ꢄꢉZZZZZZꢊ
ꢆꢂ5&+ꢃ+0ꢆꢉZZZZZZꢊ
ꢇꢂ5&+ꢃ+0ꢇꢉZZZZZZꢊ
ꢈꢂ&8+ꢃ+0ꢀꢉZZZZZZꢊ
The settings of each menu item will now be described.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Input/output signal settings
4-1-1. Setting the input mode
4-1-2. Setting the material name type
[10.1] Input Menu/SDI-IN1
1. Mode
[10.1] Input Menu/SDI-IN1
4. Name Type
[10.2] Input Menu/SDI-IN2
1. Mode
[10.2] Input Menu/SDI-IN2
4. Name Type
[10.3] Input Menu/SDI-IN3
1. Mode
[10.3] Input Menu/SDI-IN3
4. Name Type
[10.4] Input Menu/SDI-IN4
1. Mode
[10.4] Input Menu/SDI-IN4
4. Name Type
“Normal” or “DbyD” can be set for the SDI-IN1 and SDI-IN2
connector signals.
[10.5] Input Menu/DVI-IN
2. Name Type
An up-converter (UC) function is provided for the SDI-IN3
and SDI-IN4 connectors so “Normal”, “UC”, “DbyD” or
“AUTO” can be set for these connectors.
These items are for setting the type used when providing
material names for the signals which are input to each
connector.
Default:
The mode is set for each connector only when HD has been
selected as the system format setting.
When SD has been selected for the system format, “Normal”
is always set as the mode.
The default settings (INPUT1 to INPUT5) are used.
Preset:
The material names provided ahead of time are used.
The names are set using the “Name” item.
User:
Normal:
The input signals in conformity with the system format
take effect.
DbyD:
A material name is set using up to 10 characters.
The actual material names are set using the “Name”
item.
When SD signals with the same frame rate as the
system format have been input, they are input on a dot
by dot (equal size) basis with no up-conversion.
In this mode, there is minimal deterioration in the
image quality and, as such, the mode is used to
combine SD format materials using the PinP function.
ꢂ This mode can be set only when 1080i is used as
the system format.
Cam Name:
When an IP connection is established with the
AW-RP50, the remote camera names set by the
AW-RP50 are set as the material names.
UC:
When SD signals with the same frame as the system
format have been input, they are up-converted.
Auto:
Input signals in conformity with the system format take
effect.
Furthermore, if SD signals with the same frame rate
as the system format are input when HD is selected as
the system format, they are up-converted.
ꢂ In the Auto mode, the images may be disturbed
when the input signals are switched.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Input/output signal settings
4-1-3. Setting the material names
When “User” is selected
Any material names consisting of not more than 10
characters (alphanumerics and symbols which can be
expressed in ASCII codes) can be set.
[10.1] Input Menu/SDI-IN1
5. Name
[10.2] Input Menu/SDI-IN2
5. Name
When “User” is selected as the material name type setting,
the “Name” item will be displayed as shown below.
[10.3] Input Menu/SDI-IN3
5. Name
ꢀꢆꢂ0COG
#$%&ꢀꢀ^ꢀꢁ
[10.4] Input Menu/SDI-IN4
5. Name
How to set the material names:
Material names are set one character at a time.
Press the OSD/TIME dial, and move the cursor “>” to the
material name position.
Turn the OSD/TIME dial to move the blinking part to the
character input position, and press the OSD/TIME dial.
Next, the cursor “>” will move to the position where the
character is to be selected. Turn the OSD/TIME dial to select
the character, and press the OSD/TIME dial to enter the
selection.
[10.5] Input Menu/DVI-IN
3. Name
These are used to set the material names.
Material names can be set when “Preset” or “User” has been
selected as the material name type setting.
ꢂꢁ The material names are merely displayed (they cannot be
set) when “Default” or “Cam Name” has been selected as
the material name type setting.
When “Preset” is selected
4-1-4. Setting the freeze method
The materials names are set using the “type + number”
format.
[10.1] Input Menu/SDI-IN1
2. Freeze Select
Type:
C, CG, CGV, CGK, PC, V, VTR, VCR
Numbers: 1 to 9
[10.2] Input Menu/SDI-IN2
2. Freeze Select
When “Preset” is selected as the material name type setting,
the “Name” item will be displayed as shown below.
[10.3] Input Menu/SDI-IN3
2. Freeze Select
ꢀꢆꢂ0COG
%)ꢀꢀꢀꢀ^ꢀꢁ
[10.4] Input Menu/SDI-IN4
2. Freeze Select
How to set the material names:
Press the OSD/TIME dial, and move the cursor “>” to the
position where the material type is to be selected.
Turn the OSD/TIME dial to select the material type, and
press the OSD/TIME dial to enter the selection.
Next, the cursor “>” will move to the position where the
number is to be selected. Turn the OSD/TIME dial to select
the number, and press the OSD/TIME dial to enter the
selection.
These are used to select the increment in which the SDI
input signal images are to be frozen (turned into still
images).
Frame:
The images are frozen in 1-frame increments.
Field:
The images are frozen in 1-field increments.
This is used when freezing moving images.
With interlace signals, however, diagonal lines and
moving parts appear jagged.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Input/output signal settings
4-1-5. Freezing and canceling the freezing
of the input images
4-1-7. Setting the up-converter
This unit features an up-converter function.
The up-converter is set on the SDI-IN3 and SDI-IN4 menus.
[10.1] Input Menu/SDI-IN1
3. Freeze
[10.3] Input Menu/SDI-IN3
8. UC:Scale/ECPos
[10.2] Input Menu/SDI-IN2
3. Freeze
[10.4] Input Menu/SDI-IN4
8. UC:Scale/ECPos
[10.3] Input Menu/SDI-IN3
3. Freeze
Scale: “SQ,” “EC” or “LB” is set as the scaling method.
[10.4] Input Menu/SDI-IN4
3. Freeze
[10.5] Input Menu/DVI-IN
1. Freeze
Input image
SQ
SQ
EC
LB
The image is enlarged both horizontally and
vertically to fill the entire screen.
(squeeze)
These are used to freeze the SDI input signal images or
cancel the freezing of these images.
EC
(edge crop)
The aspect ratio of the image is maintained,
the image size is increased in accordance with
the vertical resolution, and black bands are
added at the left and right.
On: The images are frozen.
Off: The image freezing is canceled.
ꢂ When the multi view display is used to show the input
signals of frozen images, the “F” mark appears in front
of the material names.
LB
(letter box)
The aspect ratio of the image is maintained,
the image size is increased in accordance
with the horizontal resolution, and the image is
cropped at the top and bottom.
ECPos: The image position is finely adjusted.
This can be set only when “EC” (edge crop) has
been selected as the Scale setting.
4-1-6. Setting the video process function
The video process function works for all the SDI input signal
images.
Center
Right
Left
The image is positioned in the center, and black
images are added at the left and right.
The color tones can be changed on an image by image
basis.
The “VPrc/YGain/Ped” and “VPrc:CGain/Hue” items are
used to change them.
The image is positioned at the right, and a black
image is added at the left.
The image is positioned at the left, and a black
image is added at the right.
VPrc/YGain/Ped VPrc This is used to enable or disable the
video process function.
On: Function enabled
Off: Function disabled
[10.3] Input Menu/SDI-IN3
9. UC:Size
YGain This is used to set the gain of the Y
signal.
0.0 to 200.0
[10.4] Input Menu/SDI-IN4
9. UC:Size
Ped This is used to set the pedestal level
value.
–20.0 to 20.0
The size of the up-converted input image is adjusted using a
percentage from 0 % to 10 %.
VPrc:CGain/Hue CGain This is used to set the gain value of the
saturation.
0.0 to 200.0
Hue This is used to set the amount of change
in the hue.
0.0 to 359.9
52
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Input/output signal settings
[10.3] Input Menu/SDI-IN3
4-1-8. Setting the input image scaling
10. UC:Mvdet/Sharp
[10.4] Input Menu/SDI-IN4
10. UC:Mvdet/Sharp
[10.5] Input Menu/DVI-IN
4. Scale
Mvdet: This is used to set the motion detection sensitivity of
the image.
This is used to set the scaling for the DVI-D input signal
images.
Listed below are the resolutions of the images which can be
input.
1ꢀꢁꢁꢂ2ꢀꢁꢁꢂ3ꢀꢁꢁꢂ4ꢀꢁꢁꢂ5
Toward still images
Standard
Toward moving images
Black images will be displayed if images with other
resolutions or other frequencies are input.
Sharp: This is used to enhance the sharpness of the image
edges.
1ꢀꢁꢁꢂ2ꢀꢁꢁꢂ3ꢀꢁꢁꢂ4ꢀꢁꢁꢂ5
Resolutions supported
XGA
Not sharp edges
Standard
Very sharp edges
1024ꢄ768/60 Hz
1280ꢄ768/60 Hz
1280ꢄ1024/60 Hz
1680ꢄ1050/60 Hz
1600ꢄ1200/60 Hz
1920ꢄ1200/60 Hz
1920ꢄ1080/59.94 Hz
1920ꢄ1080/50 Hz
WXGA
SXGA
WSXGA+
UXGA
WUXGA
1080/59.94p
1080/50p
Select the scaling method from among the options listed
below.
Fit-V
Fit-H
FULL
The aspect ratio of the input image is
maintained, and the size of the image is
enlarged or reduced in accordance with the
vertical resolution.
The aspect ratio of the input image is
maintained, and the size of the image is
enlarged or reduced in accordance with the
horizontal resolution.
The size of the image is enlarged or reduced in
accordance with the system resolution.
ꢂꢁThe aspect ratio of the image is not
maintained.
ꢂꢁThe enlargement and reduction ratios
differ between the horizontal and vertical
directions.
ꢂ For details on which sizes are supported for which
formats, refer to “Table of DVI input scaling sizes” on
the next page.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Input/output signal settings
ꢅꢁTable of DVI input scaling sizes
HD/1080i
1920ꢄ1080
HD/720P
1280ꢄ720
SD/NTSC
720ꢄ487
SD/PAL
720ꢄ576
DVI format
Mode
XGA
Fit-V
720
720
ꢀꢁꢁꢂ
ꢆꢇꢂ
1024ꢄ768
576
487
ꢄꢅꢂ
ꢀꢂꢃꢂ
Fit-H
720
487
720
576
FULL
Fit-V
Fit-H
ꢀꢆꢅꢂ
ꢀꢅꢃꢂ
ꢄꢅꢂ
720
487
720
576
ꢀꢂꢃꢂ
SXGA
1280ꢄ1024
675
487
675
ꢀꢈꢉꢂ
ꢆꢂꢂ
ꢄꢅꢂ
576
ꢀꢂꢃꢂ
720
487
720
FULL
ꢀꢆꢅꢂ
ꢀꢅꢃꢂ
ꢄꢅꢂ
576
ꢀꢂꢃꢂ
WXGA
1280ꢄ768
Fit-V
Fit-H
FULL
: Black images are inserted into these areas.
: Parts of images protruding in these areas are cropped.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Input/output signal settings
HD/1080i
1920ꢄ1080
HD/720P
1280ꢄ720
SD/NTSC
720ꢄ487
SD/PAL
720ꢄ576
DVI format
WSXGA+
Mode
1728
1152
Fit-V
1680ꢄ1050
720
1080
Fit-H
720
487
720
576
1920
1440
1280
720
FULL
Fit-V
Fit-H
1080
1080
720
487
720
576
960
720
UXGA
1600ꢄ1200
720
487
720
576
720
487
720
576
1920
1728
1280
720
FULL
Fit-V
Fit-H
1080
1080
1152
720
WUXGA
1920ꢄ1200
720
487
720
576
1920
1280
720
FULL
1080
: Black images are inserted into these areas.
: Parts of images protruding in these areas are cropped.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Input/output signal settings
4-1-9. Displaying the input image information
[10.5] Input Menu/DVI-IN
5. Size
[10.5] Input Menu/DVI-IN
6. H-Freq
[10.5] Input Menu/DVI-IN
7. V-Freq
[10.5] Input Menu/DVI-IN
8. Dot Clock
These are used to display the information concerning the DVI-D input signal images.
The information cannot be changed.
Size:
This indicates the pixel count of the images.
H-Freq:
This indicates the horizontal frequency of the images.
V-Freq:
This indicates the vertical frequency of the images.
Dot Clock:
This indicates the dot clock frequency of the images.
The formats supported are listed below.
<DVI-D formats supported>
Dot clock frequency
Frequency
Horizontal
(kHz)
48.36 60.00
Input video signal
Vertical
(Hz)
(MHz)
XGA
WXGA
1024ꢄ768
1280ꢄ768
1280ꢄ1024
1680ꢄ1050
1920ꢄ1200
1600ꢄ1200
1920ꢄ1080
1920ꢄ1080
Digital
Digital
65.0
79.5
47.78
59.87
SXGA
Digital
108.0
148.3
154.0
162.0
148.5
63.98
60.02
WSXGA+
WUXGA
UXGA
Digital
65.29
59.95
Digital
74.04
59.95
Digital
75.00
60.00
1080/50P
1080/59.94P
Digital (RGB)
Digital (RGB)
56.25
50.00
148.5/1.001
67.50/1.001
60.00/1.001
ꢂꢁ If the format of the input signals is not supported, it may not be possible to import the signals properly, and a black image or
disturbed image may appear.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Input/output signal settings
4-2-2. Setting the color areas
4-2. Setting the output signals
Signals can be output from the three connectors: SDI OUT
1, SDI OUT 2 and DVI-D OUT.
The output signals are set on the [11] Output Menu of the
OSD menu.
[11] Output Menu
4. SDI-OUT:Limit
This is used to set the color area for the SDI output signal
images.
Off
The color area is not subject to any limitations.
=ꢁꢁ?ꢀ1WVRWVꢀ/GPW
108
The amplitude level of each of the colors (R, G, B) is
limited to between 0 % and 108 %.
ꢀꢁꢂ5&+ꢃ176ꢁ
ꢀꢄꢂ5&+ꢃ176ꢄ
ꢀꢆꢂ&8+ꢃ176
ꢀꢇꢂ5&+ꢃ176ꢒ.KOKV 1HH
ꢀꢈꢂ&8+ꢃ176ꢒ5K\G
2)/
289
#7:
104
100
The amplitude level of each of the colors (R, G, B) is
limited to between 0 % and 104 %.
The amplitude level of each of the colors (R, G, B) is
limited to between 0 % and 100 %.
#WVQ
ꢀꢌꢂ&8+ꢃ176ꢒ5ECNG (KVꢃ8
ꢀꢎꢂ&8+ꢃ176ꢒ/XFGV ꢓꢀꢀꢀꢀꢀꢆ
4-2-3. Setting the DVI-D output signals
The following setting is selected for DVI-D output signal
images.
4-2-1. Assigning the output signals
[11] Output Menu
5. DVI-OUT:Size
[11] Output Menu
1. SDI-OUT1
This is used to set the resolution to be output.
The following resolutions are supported.
[11] Output Menu
2. SDI-OUT2
Supported resolutions
[11] Output Menu
3. DVI-OUT
Auto
Using the DVI signals, the information of the
device at the output destination is gathered,
and the images are output at the optimum
resolution.
The following assignment options are available.
ꢂꢁThe vertical frequency is set to 60 Hz, and
the maximum resolution is WUXGA.
PGM
This is the main line output of the switcher.
Images with wipe, mix, key, PinP or other effects
added are output.
XGA
1024ꢄ768
1280ꢄ768
1280ꢄ1024
1680ꢄ1050
1600ꢄ1200
1920ꢄ1200
1920ꢄ1080
1920ꢄ1080
PVW
CLN
The PVW images which enable the next
operation to be checked are output.
WXGA
SXGA
Clean signals (images resulting when the key and
PinP effects have been removed from the PGM
signal) are output.
WSXGA+
UXGA
WUXGA
1080/59.94p
1080/50p
AUX
The signal selected using the AUX bus is output.
The multi view display signal is output.
The key signal is output.
MV
KeyOut
57
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Input/output signal settings
[11] Output Menu
6. DVI-OUT:Scale
This is used to select one of the scaling methods listed
below.
Fit-V
Fit-H
FULL
The aspect ratio of the output image is
maintained, and the size of the image is
enlarged or reduced in accordance with the
vertical resolution.
ꢂꢁBlack images are inserted into areas where
there are no images.
ꢂꢁParts of images that protrude are cropped.
The aspect ratio of the output image is
maintained, and the size of the image is
enlarged or reduced in accordance with the
horizontal resolution.
ꢂꢁBlack images are inserted into areas where
there are no images.
ꢂꢁParts of images that protrude are cropped.
The size of the output image is enlarged
or reduced in accordance with the system
resolution.
ꢂꢁThe aspect ratio of the image is not
maintained.
ꢂꢁThe enlargement and reduction ratios
differ between the horizontal and vertical
directions.
[11] Output Menu
6. DVI-OUT:Mvdet
This is used to set the sensitivity with which the motion of
moving images is to be detected.
1ꢀꢁꢁꢂ2ꢀꢁꢁꢂ3ꢀꢁꢁꢂ4ꢀꢁꢁꢂ5
Toward still images
Standard
Toward moving images
58
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Setting the multi view display
The screen of an external monitor can be split into a number
of sections, and images such as input images and program
image can be positioned in the sections and displayed.
<Split screen layouts>
1
3
2
4
5-1. Screen layout
The multi view display layout is set using the [7] MultiView
Pattern Menu of the OSD menu.
4Split
=ꢎ?ꢀ/WNVK8KGYꢀ2CVVGTPꢀ/GPW
ꢀꢁꢂ5RNKV
ꢁꢑꢃC5RNKV
2)/
289
5&+ꢃ+0ꢁ
5&+ꢃ+0ꢄ
5&+ꢃ+0ꢆ
5&+ꢃ+0ꢇ
&8+ꢃ+0
(/'/ꢁ
ꢀꢄꢂ2QUꢁꢀ5QWTEG
ꢀꢆꢂ2QUꢄꢀ5QWTEG
ꢀꢇꢂ2QUꢆꢀ5QWTEG
ꢀꢈꢂ2QUꢇꢀ5QWTEG
ꢀꢌꢂ2QUꢈꢀ5QWTEG
ꢀꢎꢂ2QUꢌꢀ5QWTEG
ꢀꢏꢂ2QUꢎꢀ5QWTEG
ꢀꢐꢂ2QUꢏꢀ5QWTEG
ꢁꢑꢂ2QUꢐꢀ5QWTEG
ꢁꢁꢂ2QUꢁꢑꢀ5QWTEG
3
4
5
1
2
3
4
5
1
2
5-aSplit
5-bSplit
(/'/ꢄ
#7:
3
4
5
6
1
2
[7] MultiView Pattern Menu
1. Split
3
4
5
6
1
2
6-aSplit
6-bSplit
The following eight options are available as split screen
layouts.
4Split
5-aSplit
9Split
5-bSplit
6-aSplit
1
4
7
2
5
3
6
9
6-bSplit
10-aSplit
10-bSplit
8
[7] MultiView Pattern Menu
2. Pos1 Source
9Split
ꢃ
7
3
8
4
9
5
10
6
[7] MultiView Pattern Menu
11. Pos10 Source
1
2
This is used to set the names of the signals to be displayed
in split screens 1 to 10.
3
7
4
8
5
9
6
10
1
2
SDI-IN1 to 4
(material names)
DVI-IN
(material names)
10-aSplit
10-bSplit
CBGD
PVW
FMEM1
FMEM2
KeyOut
PGM
AUX
ꢂꢁ Depending on the setting selected for the “1. Split” item,
the “6. Pos5 Source” to “11. Pos10 Source” items may not
be displayed.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Setting the multi view display
5-2. Setting the split frames and
characters
The frames, character luminance and background to be
used for the split screens can be set.
5-3. Setting the tally displays
The tally displays to be superimposed onto the split screen
frames can be set.
The red tally indicates the material consisting of program
outputs.
The green tally indicates the material selected by the preset
bus.
If frames are displayed, the red tally or green tally is
displayed on the frames.
If the frames are not displayed, the red tally and green tally
are displayed on the left of the material names.
The settings are selected on the [8] MultiView Out/Frame
Menu of the OSD menu.
=ꢏ?ꢀ/WNVK8KGYꢀ1WVꢋ(TCOGꢀ/GPW
ꢀꢁꢂ(TCOG
ꢀꢄꢂ%JCTCEVGT
ꢀꢆꢂ.CDGN
.7/ꢀꢎꢈꢔ
.7/ꢀꢎꢈꢔ
1P
ꢀꢇꢂ6CNN[
ꢀꢈꢂ.GXGNꢀ/GVGT
ꢀꢌꢂ+PRWVꢀ5CVWU
4GFꢅ)TGGP
1HH
1P
[8] MultiView Out/Frame Menu
4.Tally
This is used to set the tally displays.
Red+GRN:
Both the red tally and green tally are displayed.
Red: Only the red tally is displayed.
Off: No tally displays are shown.
[8] MultiView Out/Frame Menu
1. Frame
ꢂ The red tally signals are output from the unit’s TALLY/
GPI connector.
ꢂ The red tally is not displayed during FTB operations
while the program images have been completely faded
out to a black screen.
This is used to set the split frame brightness and, if the
frame is to be displayed, to decide whether the split frames
are to be displayed.
LUM (0%, 25%, 50%, 75%, 100%):
The split frame (gray scale) luminance is set.
Off:
During times like this, the green tally is displayed for
images consisting of program images.
However, the red tally will be displayed if FMEM1,
FMEM2 or CBGD has been selected using the menu
item below.
The split frame is not displayed.
[8] MultiView Out/Frame Menu
2. Character
[1] TIME/CBGD Menu
5. FTB Source
This is used to set the character brightness and, if the frame
is to be displayed, decide whether the characters are to be
displayed.
LUM (0%, 25%, 50%, 75%, 100%):
The character (gray scale) luminance is set.
Off:
The characters are not displayed.
ꢂ If the input signals have been frozen, an “F” mark is
displayed in front of the material names.
[8] MultiView Out/Frame Menu
3. Label
This is used to decide whether to display the character
background (half tones).
On: The character background is displayed.
Off: The character background is not displayed.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Setting the multi view display
5-4. Setting the level meters
5-5. Setting the input signal marks
Level meters for the embedded audio signals transferred by
the SDI input can be displayed on the split screens.
Left display:
The status of the input signals can be displayed in front of
the material names displayed on the split screens.
“F” mark
“ ! ” mark
“C” mark
This appears when the input signals are
frozen.
Channel 1 of group 1
Right display:
Channel 2 of group 1
This appears when there are no input
signals.
This appears when the signals from
a remote camera controlled by the
AW-RP50 are input.
[8] MultiView Out/Frame Menu
5. Level Meter
On: The level meters are displayed.
Off: The level meters are not displayed.
[8] MultiView Out/Frame Menu
6. Input Status
On: The input signal status is displayed.
Off: The input signal status is not displayed.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
6. System settings
<How to specify the video format and then start
the system>
6-1. System menu settings
With the unit in the power-off status, the video format can be
specified and the system started.
Set the POWER switch to ON while holding down one
combination of the buttons listed below that corresponds to
the video format.
6-1-1. Setting the video format
The video format of the entire system to which the unit is
connected can be set.
=ꢁꢇ?ꢀ5;56'/ꢀ/GPW
Button to press at the same time
[OSD ON] + A bus crosspoint [1]
[OSD ON] + A bus crosspoint [2]
[OSD ON] + A bus crosspoint [3]
[OSD ON] + A bus crosspoint [4]
[OSD ON] + A bus crosspoint [5]
[OSD ON] + B bus crosspoint [1]
[OSD ON] + B bus crosspoint [2]
[OSD ON] + B bus crosspoint [3]
Video format
1080/59.94i
ꢀꢁꢂ(QTOCV
ꢀꢄꢂ*K4GU/8
ꢀꢆꢂꢁꢌꢒꢐ53
ꢀꢇꢂ#7:ꢀ#PEK
ꢀꢈꢂ2)/ꢀ#PEK
ꢀꢌꢂ289ꢀ#PEK
ꢀꢎꢂ/8ꢀ#PEK
ꢁꢑꢏꢑꢋꢈꢐꢂꢐꢇK
1HH
1HH
1HH
1HH
1HH
1HH
1HH
1080/50i
720/59.94p
720/50p
1080/24psf
1080/23.98psf
480/59.94i
576/50i
ꢀꢏꢂ+PKVKCN
ꢀꢐꢂ+2ꢀ#FFTGUU
ꢁꢑꢂ5WDPGVꢀ/CUM
ꢁꢁꢂ)CVGYC[
ꢀꢀꢁꢐꢄꢂꢀꢀꢁꢌꢏꢂꢀꢀꢀꢀꢑꢂꢀꢀꢀꢆꢑ
ꢀꢀꢄꢈꢈꢂꢀꢀꢄꢈꢈꢂꢀꢀꢄꢈꢈꢂꢀꢀꢀꢀꢑ
ꢀꢀꢁꢐꢄꢂꢀꢀꢁꢌꢏꢂꢀꢀꢀꢀꢑꢂꢀꢀꢀꢀꢁ
ꢂ After the POWER switch has been set to ON, keep
ꢁꢄꢂ/#%ꢀ#FFTGUU
holding down the buttons until an image is output.
Note
[14] SYSTEM Menu
2. HiResMV
The [14] SYSTEM Menu settings cannot be changed if
“Locked” has been set using the menu item below.
This is used to decide whether to set the high-resolution
multi view mode. When SD has been selected as the
system’s video format setting, images can be output at high
resolution as the DVI-D output.
[13] Operation Menu
14. SYSTEM Menu
If this is the case, the multi view display is set for the DVI
OUT connector output.
The multi view display cannot be set for the SDI OUT
connector output.
[14] SYSTEM Menu
1. Format
Select the supported format from among the options
provided below.
On: The high-resolution multi view mode is enabled.
Off: The high-resolution multi view mode is disabled.
Supported formats
1080/59.94i
720/59.94p
1080/24psf
480/59.94i
1080/50i
[14] SYSTEM Menu
3. 16:9SQ
720/50p
1080/23.98psf
576/50i
This is used to set the 16:9 squeeze mode.
It can be set when SD has been selected as the system’s
video format setting.
When the 16:9 squeeze mode is selected, SD format
images are provided with a border width that factors in
cases where the images are to be converted into the 16:9
aspect ratio.
<Border width (graphical representation) when the
squeeze mode is supported>
Squeeze (4:3)
16:9
62
Download from Www.Somanuals.com. All Manuals Search And Download.
6. System settings
6-1-2. Setting the ancillary data
A function for allowing the V ancillary data and embedded
audio data of the SDI input signals to pass through can be
set.
[14] SYSTEM Menu
7. MV Anci
PGM:The ancillary data and embedded audio data of the
SDI input materials selected by the PGM bus are
allowed to pass through.
PVW:The ancillary data and embedded audio data of the
SDI input materials selected by the PST bus are
allowed to pass through.
When an HD format is used:
The ancillary data starting with line 9 is allowed to
pass through.
When an SD format is used:
The ancillary data starting with line 12 is allowed to
pass through.
ꢂ If SD format signals are input while the HD format has
been set as the system format, it will not be possible to
allow the ancillary data and embedded audio data to
pass through.
Off: The ancillary data and embedded audio data are not
allowed to pass through.
[14] SYSTEM Menu
4. AUX Anci
On: The ancillary data and embedded audio data of the
SDI input materials selected by the AUX bus are
allowed to pass through.
Off: The ancillary data and embedded audio data are not
allowed to pass through.
ꢂ The data is not allowed to pass through when KEY
OUT or CLN material has been selected.
[14] SYSTEM Menu
5. PGM Anci
On: The ancillary data and embedded audio data of the
SDI input materials selected by the PGM bus are
allowed to pass through.
Off: The ancillary data and embedded audio data are not
allowed to pass through.
[14] SYSTEM Menu
6. PVW Anci
On: The ancillary data and embedded audio data of the
SDI input materials selected by the PST bus are
allowed to pass through.
Off: The ancillary data and embedded audio data are not
allowed to pass through.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
6. System settings
6-1-3. System initialization
6-1-4. Network settings
The network settings for upgrading the software versions
and other data can be selected.
[14] SYSTEM Menu
8. Initial
If “Yes” is selected, the setting data is returned to the initial
values.
ꢂꢁ However, the network settings will not be initialized.
[14] SYSTEM Menu
9. IP Address
This is used to set the IP address.
Initial value: 192.168.0.30
[14] SYSTEM Menu
10. Subnet Mask
This is used to set the subnet mask.
Initial value: 255.255.255.0
[14] SYSTEM Menu
11. GateWay
This is used to set the gateway.
Initial value: 192.168.0.1
[14] SYSTEM Menu
12. MAC Address
The MAC address is displayed.
ꢂꢁ For the network settings to take effect, the system must
be rebooted. Turn off the power, and then turn it back on.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
6. System settings
6-2. Operation menu settings
[13] Operation Menu
1. OSD Size
6-2-1. OSD (on-screen display) settings
The menu screens can be superimposed onto the images
output from the SDI OUT 2 connector and DVI OUT
connector, and displayed.
The OSD size and position can be selected from the options
listed below.
Full
Full size of screen
Upper-Left
Upper-Right
Lower-Right
Lower-Left
As shown in the figure below, the menu
appears in one-fourth of the full size of
the screen, and it is positioned in one of
the four quadrants.
=ꢁꢆ?ꢀ1RGTCVKQPꢀ/GPW
ꢀꢁꢂ15&ꢀ176
ꢀꢄꢂ15&ꢀ5K\G
ꢀꢆꢂ15&ꢀ$CEM
ꢀꢇꢂ-G[ꢀ2TKQTKV[
ꢀꢈꢂ$75ꢀ/QFG
ꢀꢌꢂ6KOGꢀ7PKV
ꢀꢎꢂ5NKFGꢀ.GXGT
ꢀꢏꢂ)2+ꢀ+PRWV
ꢀꢐꢂ)2+ꢀ1WVRWV
ꢁꢑꢂ%CO%QPVꢀ.KPM
ꢁꢁꢂ(#0
5&+ꢃ176ꢄꢅ&8+ꢃ176
(WNN
1P
2KP2ꢀQXGTꢀ-';
2)/ꢉ#ꢊꢋ256ꢉ$ꢊ
5GEꢍ(TCOG
$-)&
'PCDNG
'PCDNG
1HH
ꢃ
Upper-
Left
Upper-
Right
Lower-
Left
Lower-
Right
ꢂ If parts of the OSD overlap the multi view display
ꢁꢄꢂ2QYGT
ꢃ
frames, the frame displays will be hidden.
ꢁꢆꢂ6GORCTCVWTG
ꢁꢇꢂ5;56'/ꢀ/GPW
ꢃ
7P.QEMGF
[13] Operation Menu
3. OSD Back
[13] Operation Menu
1. OSD OUT
On: A black background is displayed for the OSD.
Off: A black background is not displayed for the OSD.
Select the connector to be used for outputting the OSD
displays from the options listed below.
SDI-OUT2
DVI-OUT
SDI-OUT2+DVI-OUT
ꢂꢁ The SDI OUT2+DVI-OUT option is selected when the
OSD ON button is pressed while the SHIFT button is
pressed.
When this is done, “AUTO” is selected as the following
menu setting.
[11] OUTPUT MENU
5. DVI-OUTSIZE
65
Download from Www.Somanuals.com. All Manuals Search And Download.
6. System settings
6-2-2. Other settings
[13] Operation Menu
10. CamCont Link
[13] Operation Menu
4. Key Priority
This is used to set linked control with the AW-RP50 to ON or
OFF.
ꢀ For details, refer to “3-3. KEY”.
On: Link control is set to ON.
Off: Link control is set to OFF.
ꢂ For details on what is controlled, refer to “??? Function
[13] Operation Menu
5. BUS Mode
for linking up with the remote camera controller ???”.
ꢀ For details, refer to “3-1-4. Selecting the bus mode”.
[13] Operation Menu
11. FAN
[13] Operation Menu
6.Time Unit
This displays “Alarm” when something is wrong with the
cooling fan.
ꢀ For details, refer to “3-1-7. Auto transition”.
[13] Operation Menu
12. Power
[13] Operation Menu
7. Slide Lever
This displays “Alarm” when a drop in the supply voltage has
been detected.
ꢀ For details, refer to “3-1-6. Manual transitions”.
[13] Operation Menu
13.Temperature
[13] Operation Menu
8. GPI Input
This displays “Alarm” when the temperature inside the unit
has risen.
This is used to enable or disable control from the GPI input
port.
Enable: Control is enabled.
Disable: Control is disabled.
ꢂ For details on what is controlled, refer to “7-2. TALLY/
GPI”.
If an alarm has occurred, stop using the unit
immediately, and be sure to contact your dealer.
Continuing to use the unit in this condition could
damage it.
[13] Operation Menu
9. GPI Output
[13] Operation Menu
14. SYSTEM Menu
This is used to enable or disable control from the GPI output
port.
When “Locked” is selected as this item’s setting, it is not
possible to change the [14] SYSTEM Menu settings.
Select this setting when it is not desirable for the [14]
SYSTEM Menu settings to be changed easily.
Enable: Control is enabled.
Disable: Control is disabled.
ꢂ For details on what is controlled, refer to “7-2. TALLY/
GPI”.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
6. System settings
6-2-3. Bus status displays
6-2-4. Version displays
When the A bus or B bus crosspoint buttons are held down,
the BUS Assign Status menu appears for the OSD menu.
The numbers of the versions are displayed on the [15]
SYSTEM Status OSD menu.
$75ꢀ#UKIPꢀ5VCVWU
=ꢁꢈ?ꢀ5;56'/ꢀ5VCVWUꢀ/GPW
ꢁꢂ:26ꢀ59
ꢄꢂ:26ꢀ59ꢀ#UKIP
ꢁ
ꢁꢂ5;56'/ꢀ8GTꢂ
ꢄꢂ51(6ꢀ8GTꢂ
ZZZZZZZZZZZ
ZZZZZZZZZZZ
5&+ꢃ+0ꢁꢀꢉꢀ+0276ꢁꢀꢀꢀꢊ
ꢀꢃꢀꢃꢀꢃꢀꢃꢀꢃꢀꢃꢀꢃꢀꢃꢀꢃꢀꢃꢀꢃꢀꢃꢀꢃꢀꢃꢀꢃꢀꢃꢀꢃꢀꢃꢀꢃꢀꢃꢀꢃ
ꢆꢂ).7'ꢀ(2)#ꢀ8GTꢂ ZZZZZZZZZZZ
ꢇꢂ/#+0ꢀ(2)#ꢀ8GTꢂ ZZZZZZZZZZZ
ꢆꢂ2)/
5&+ꢃ+0ꢁꢀꢉꢀ+0276ꢁꢀꢀꢀꢊ
ꢇꢂ289
5&+ꢃ+0ꢄꢀꢉꢀ+0276ꢄꢀꢀꢀꢊ
ꢈꢂ(106ꢀ8GTꢂ
ZZZZZZZZZZZ
ꢈꢂ#7:
/8
ꢌꢂ2KP2
5&+ꢃ+0ꢁꢀꢉꢀ+0276ꢁꢀꢀꢀꢊ
ꢎꢂ-';ꢀ(KNN
ꢏꢂ-';ꢀ5QWTEG
%$)&
(/'/ꢁ
[15] SYSTEM Status
1. SYSTEM Ver
The system version information is displayed here.
[15] SYSTEM Status
2. SOFT Ver
The unit’s software version is displayed here.
[15] SYSTEM Status
3. GLUE FPGA Ver
The version of the hardware used to start the unit is
displayed here.
[15] SYSTEM Status
4. MAIN FPGA Ver
The version of the hardware that processes the images is
displayed here.
[15] SYSTEM Status
5. FONT Ver
The version of the font used for the OSD menu is displayed
here.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
7. External device control interfaces
7-1. LAN connection
Use LAN cables to connect the AW-HE50, AW-RP50 and host computer.
When connecting the unit directly to another device, use a crossover cable.
For network connections via a device such as a hub, use straight cables.
When a hub is not going to be used, ensure that the length of the LAN cable does not exceed 100 meters (328 ft.) (when a
CAT5E cable is used).
ꢂꢁ For further details on the AW-HE50 and AW-RP50 connections and settings, refer to “2-2-2. Example of connections”.
ꢂꢁ For details on the functions available when connection has been made to the host computer, refer to “8. Connections with a
computer”.
7-2. TALLY/GPI
The TALLY/GPI connector features five contact input ports
for controlling the unit from an external device and seven
open collector output ports for outputting the tally and status
information from the unit to an external device.
D-sub 15-pin, female, inch thread
8
1
9
15
Pin
no.
Signal
Input/output
Details of signal
Operation
1
TALLY OUT1
TALLY OUT2
TALLY OUT3
TALLY OUT4
TALLY OUT5
ALARM
Open collector output
Open collector output
Open collector output
Open collector output
Open collector output
Open collector output
Tally output of input image 1
Tally output of input image 2
Tally output of input image 3
Tally output of input image 4
Tally output of input image 5
Fan alarm or power alarm output
A low-level signal is output during tally
output.
2
3
4
5
6
A low-level signal is output when trouble
has occurred.
7
KEY ON
Open collector output
Contact input
Key combination status output
A low level is output during key
combinations.
8
9
(RESERVE)
NC
(Reserve)
Not used
10
Tally Disable
Contact input
Tally signal enable/disable
This signal is enabled by the contact
input (and disabled when open).
11
12
13
14
15
AUTO
CUT
Contact input
Contact input
Contact input
Contact input
Ground
AUTO button of transition part
CUT button of transition part
KEY ON button of transition part
PinP button of transition part
Ground
The signal is made operational by the
contact input (30 ms or more).
KeyON
PinPON
GND
Example of an open collector output connection
Ensure that the conditions given below are satisfied.
Dielectric strength: Max. DC 24 V
Example of a contact input connection
Provide contact inputs.
Current:
Max. 50 mA
AW-HS50
+3.3 V
(Max. voltage: 24 V)
Tally LED
AW-HS50
GPI In
Com
GPI Out
ALARM Out
(Max. current: 50 mA)
Com
68
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Connections with a computer
8-1. Image transmission functions
When the unit and computer are connected using a LAN cable, the unit’s data can be saved in (downloaded to) the computer
and data can be written (uploaded) from the computer to the unit.
The following kinds of data can be downloaded and uploaded.
• Frame memory images (FMEM1, FMEM2)
• Menu settings
• Panel statuses
ꢂ Network information (IP address, subnet mask, gateway and MAC address) cannot be uploaded.
ꢂ The image formats compatible with the frame memories include bitmap (bmp), JPEG (jpg), TIFF (tif), GIF (gif) and PNG
(png).
Images can be converted automatically to the size of the format specified.
In order to use this function, the “Image transmission software” must be installed into the host computer from the CD provided.
For details on how to install the application, refer to “8-3. How to install the software”.
8-2. Connections
A LAN cable is used to connect the host computer to the unit’s LAN connector.
When connecting the unit directly to the host computer, use a crossover cable.
When making the connection through a device such as a hub, use a straight cable.
For details on the IP address and other network settings, refer to “6-1-4. Network settings”.
Crossover cable
Straight cable
Straight cable
Hub
69
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Connections with a computer
8-3. How to install the software
This section describes how to install the image transmission software (HS50 Tool).
Windows XP is used as the host computer’s operating system in the example given here.
1. Insert the CD-ROM supplied with the unit into the CD-ROM drive of the host computer in which the program will be
installed. (Here, E: will serve as the name of this drive for example.)
2. Execute the setup program (E:\HS50TOOL\ENG\SETUP.EXE\).
3. The installer now starts up so follow its instructions to proceed.
4. The Setup Complete screen appears to indicate that installation is complete.
Click [Finish] to close the window.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Connections with a computer
8-4. Basic operations of software
This section describes how to operate the image transmission software (HS50 Tool).
<Startup>
On the Start menu of Windows, select [Programs] ? [Panasonic] ? [AV-HS50Tool] ? [HS50Tool].
The main screen now appears.
<Exit>
Click the [CLOSE] button.
<Setting the IP address>
Set the unit’s IP address in the IP Address setting box.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Connections with a computer
8-5. Image transfer
8-5-1. Transferring images from the computer to the unit
1. Select the mode.
Check that [To HS50] appears in the [Mode] field.
If [From HS50] appears instead, click the [From HS50] button so that [To HS50] appears.
2. Select the transmission destination of the images in the [Target] field.
FMEM1: Unit’s frame memory 1
FMEM2: Unit’s frame memory 2
3. When the [Select Image] button is clicked, the file selection dialog box appears on the screen.
Select the image file to be transmitted, and click [OK].
The image is now displayed in the image display area, and its horizontal and vertical dimensions appear in the [Width]
and [Height] fields at the bottom right.
4. In the [Size] field, select the size of the image to be transmitted to the unit.
HD1080 (1920ꢃ1080), HD720 (1280ꢃ720), SD480 (720ꢃ487) or SD576 (720ꢃ576) can be selected as the size.
If the image is in a different video format from the ones supported by the unit, the output will not be displayed properly.
5. In the [Aspect] field, select the scaling method.
If the size of the image to be transmitted and the selected image differ, the image will be automatically scaled according
to one of the following methods.
Full: The size of the image is increased or reduced so that it fits the size selected in the [Size] field.
If the aspect ratio of the image to be transmitted differs from that of the selected image, the ratio between the
horizontal and vertical dimensions will be changed.
Keep: The image is expanded or reduced while its original aspect ratio is kept unchanged.
Any empty spaces in the image will appear black.
6. The [RGBA(1&2)] button can be selected when images containing the alpha channel are to be transmitted.
Click the [RGBA(1&2)] button and select FMEM1 in the [Target] field to transmit the RGB images to frame memory 1
(FMEM1) and the alpha channel images to frame memory 2 (FMEM2).
When the [Display Alpha] button is clicked, the alpha channel images appear as a preview display.
7. When the [Send] button is clicked, images are transmitted to the unit and images are saved in frame memory and flash
memory.
ꢂ When not saving images in the flash memory, click the [Write Flash] button to deselect the [Write Flash] button.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Connections with a computer
8-5-2. Transferring the unit’s images to the computer
1. Select the mode.
Check that [From HS50] appears in the [Mode] field.
If [To HS50] appears instead, click the [To HS50] button so that [From HS50] appears.
2. Select the images to be imported to the host computer in the [Target] field.
FMEM1: Images in unit’s frame memory 1
FMEM2: Images in unit’s frame memory 2
3. When the [Get] button is clicked, the image is imported from the unit.
The image is now displayed in the image display area, and its horizontal and vertical dimensions appear in the Width and
Height fields at the bottom right.
4. When the [Save Image] button is clicked, the file save dialog box appears on the screen.
Select the image file to be transmitted, and click [Save].
73
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Connections with a computer
<Transferring the setup data to the unit>
未
74
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Connections with a computer
<Transferring the setup data from the unit>
未
75
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Setting menu tables
No.
Sub menu
Setting item
1 AUTO Time
Setting
0 to 999f
0f
1 TIME/CBGD Menu
Setting range 0 to 33s (59.94Hz)
Initial value 1s
2 PinP Time
3 KEY Time
Setting range 0 to 33s (59.94Hz)
Initial value 1s
Setting range 0 to 33s (59.94Hz)
Initial value 1s
0 to 999f
0f
0 to 999f
0f
4 FTB Time
Setting range 0 to 33s (59.94Hz)
Initial value 1s
0 to 999f
0f
5 FTB Source
6 AUX BUS Trans
7 PinP BUS Trans
8 PinP EFFDSLV
9 Set CBGD Col
10 Adj CBGD Col
1 Pattern
Setting range FMEM1, FMEM2, CBGD, White, Black
Initial value Black
Setting range 0 to 33s (59.94Hz)
Initial value 1s
0 to 999f
0f
Enable, Disable
Enable
Enable, Disable
Enable
Enable, Disable
Enable
Setting range 0 to 33s (59.94Hz)
Initial value 1s
0 to 999f
0f
Setting range 0 to 33s (59.94Hz)
Initial value 1s
0 to 999f
0f
Setting range White, Yellow, Cyan, Green, Magenta, Red, Blue, Black
Initial value White
Setting range
Initial value
0.0 to 359.9
0.0
0.0 to 100.0
0.0
0.0 to 108.0
100.0
H
S
L
2 WIPE Menu
Setting range 1 to 13
Initial value
1
2 Direction
Setting range N, R, N/R
Initial value N/R
3 Border Width
4 Set Border Col
5 Adj Border Col
6 Soft Width
Setting range 0.0 to 100.0
Initial value 0.0
Setting range White, Yellow, Cyan, Green, Magenta, Red, Blue, Black
Initial value White
Setting range
Initial value
0.0 to 359.9
0.0
0.0 to 100.0
0.0
0.0 to 108.0
100.0
H
S
L
Setting range 0.0 to 100.0
Initial value 0.0
7 Position
Setting range
Initial value
–100.00 to 100.00
0.00
–100.00 to 100.00
0.00
X
Y
8 Set To Preset
1 Shape
Setting range 1 to 4
Initial value
Setting range Square, Circle, Heart, Flower, Star
Initial value Square
1
3 PinP Menu
2 Pos:X/Y/Size
3 PVW
Setting range
Initial value
Setting range On, Off
Initial value Off
–100.00 to 100.00
0.00
–100.00 to 100.00
0.00
0.00 to 100.00
25.00
X
Y
S
4 Border Width
5 Set Border Col
6 Adj Border Col
7 Soft Width
Setting range 0.0 to 100.0
Initial value 0.0
Setting range White, Yellow, Cyan, Green, Magenta, Red, Blue, Black
Initial value White
Setting range
Initial value
0.0 to 359.9
0.0
0.0 to 100.0
0.0
0.0 to 108.0
100.0
H
S
L
Setting range 0.0 to 100.0
Initial value 0.0
8 Trim Adjust1
9 Trim Adjust2
10 Set To Preset
Setting range Manual, Off, 4:3
Initial value Off
–50.00 to 50.00
–40.00
–50.00 to 50.00
–40.00
–50.00 to 50.00
40.00
L
T
Setting range
Initial value
–50.00 to 50.00
40.00
R
B
Setting range 1 to 4
Initial value
1
76
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Setting menu tables
No.
Sub menu
Setting item
Setting
4 KEY Setup Menu
1 Key Type
2 Fill
Setting range Luminance, Linear, Chroma
Initial value Luminance
Setting range Bus, Matte
Initial value Bus
3 PVW
Setting range On, Off
Initial value Off
4 Set Fill Col
5 Adj Fill Col
6 Edge Type
7 Edge Direction
8 Edge Width
9 Set Edge Col
10 Adj Edge Col
1 Clip
Setting range White, Yellow, Cyan, Green, Magenta, Red, Blue, Black
Initial value White
Setting range
Initial value
0.0 to 359.9
0.0
0.0 to 100.0
0.0
0.0 to 108.0
100.0
H
S
L
Setting range Off, Border, Drop, Shadow, Outline
Initial value Off
Setting range 0, 45, 90, 135, 180, 225, 270, 315
Initial value
Setting range 0 to 4
Initial value
0
2
Setting range White, Yellow, Cyan, Green, Magenta, Red, Blue, Black
Initial value Black
Setting range
Initial value
0.0 to 359.9
0.0
0.0 to 100.0
0.0
0.0 to 108.0
0.0
H
S
L
5 KEY Adjust Menu
Setting range 0.0 to 108.0
Initial value 0.0
2 Gain
Setting range 0.0 to 200.0
Initial value 100.0
Setting range 0.0 to 100.0
Initial value 100.0
Setting range On, Off
Initial value Off
3 Density
4 Invert
5 Mask
Setting range On, Off
Initial value Off
6 Mask Adjust1
7 Mask Adjust2
8 Mask Invert
1 Marker
Setting range
Initial value
Setting range
Initial value
Setting range On, Off
Initial value Off
–50.00 to 50.00
–25.00
–50.00 to 50.00
25.00
–50.00 to 50.00
25.00
–50.00 to 50.00
–25.00
L
T
R
B
6 ChromaKey Menu
Setting range On, Off
Initial value Off
2 Sample
Setting range Start
Initial value Start
3 Marker Pos
4 Marker Aspect
5 Ref Adjust
6 Y-Influence
7 Radius
Setting range
Initial value
Setting range –50.00 to 50.00
Initial value 0.00
Setting range
Initial value
Setting range 0.0 to 100.0
Initial value 0.00
–50.00 to 50.00
0.00
–50.00 to 50.00
0.00
0.00 to 25.00
10.00
X
Y
S
S
S
L
0.0 to 359.9
354.0
0.0 to 100.0
100.0
0.0 to 108.0
7.0
H
Setting range
Initial value
0.0 to 100.0
100.0
0.0 to 100.0
50.0
H
8 Soft
Setting range 0.0 to 100.0
Initial value 0.0
9 Cancel
Setting range 0.0 to 100.0
Initial value 0.0
77
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Setting menu tables
No.
Sub menu
Setting item
Setting
Setting range 4Split, 5-aSplit, 5-bSplit, 9Split, 10-aSplit, 10-bSplit
Initial value 10-aSplit
7 MultiView Pattern Menu
1 Split
2 Pos1 Source
3 Pos2 Source
4 Pos3 Source
5 Pos4 Source
6 Pos5 Source
7 Pos6 Source
8 Pos7 Source
9 Pos8 Source
10 Pos9 Source
11 Pos10 Source
Setting range SDI-IN1 to 4(Input Name), DVI-IN(Input Name), FMEM1, FMEM2,
CBGD, CBAR, Black, NoAsign
Initial value PGM
Setting range SDI-IN1 to 4(Input Name), DVI-IN(Input Name), FMEM1, FMEM2,
CBGD, CBAR, Black, NoAsign
Initial value PVW
Setting range SDI-IN1 to 4(Input Name), DVI-IN(Input Name), FMEM1, FMEM2,
CBGD, CBAR, Black, NoAsign
Initial value Input1(Input Name)
Setting range SDI-IN1 to 4 (Input Name), DVI-IN(Input Name), FMEM1, FMEM2,
CBGD, CBAR, Black, NoAsign
Initial value Input2(Input Name)
Setting range SDI-IN1 to 4 (Input Name), DVI-IN(Input Name), FMEM1, FMEM2,
CBGD, CBAR, Black, NoAsign
Initial value Input3(Input Name)
Setting range SDI-IN1 to 4(Input Name), DVI-IN(Input Name), FMEM1, FMEM2,
CBGD, CBAR, Black, NoAsign
Initial value Input4(Input Name)
Setting range SDI-IN1 to 4(Input Name), DVI-IN(Input Name), FMEM1, FMEM2,
CBGD, CBAR, Black, NoAsign
Initial value DVI-D(Input Name)
Setting range SDI-IN1 to 4(Input Name), DVI-IN(Input Name), FMEM1, FMEM2,
CBGD, CBAR, Black, NoAsign
Initial value FMEM1
Setting range SDI-IN1 to 4(Input Name), DVI-IN(Input Name), FMEM1, FMEM2,
CBGD, CBAR, Black, NoAsign
Initial value FMEM2
Setting range SDI-IN1 to 4(Input Name), DVI-IN(Input Name), FMEM1, FMEM2,
CBGD, CBAR, Black, NoAsign
Initial value AUX
8 MultiView Out/Frame Menu
1 Frame
Setting range LUM0%, LUM25%, LUM50%, LUM75%, LUM100%, Off
Initial value LUM75%
2 Character
3 Label
Setting range LUM0%, LUM25%, LUM50%, LUM75%, LUM100%, Off
Initial value LUM75%
Setting range On, Off
Initial value On
4 Tally
Setting range Red, Red+Green, Off
Initial value Red+Green
5 Level Meter
6 Input Status
1 XPT1
Setting range On, Off
Initial value Off
Setting range On, Off
Initial value On
Setting range SDI-IN1 to 4(Input Name), DVI-IN(Input Name), FMEM1, FMEM2,
CBGD, CBAR, Black, NoAsign
9 XPT SW Assign Menu
Initial value SDI-IN1(Input Name)
2 XPT2
3 XPT3
4 XPT4
Setting range SDI-IN1 to 4(Input Name), DVI-IN(Input Name), FMEM1, FMEM2,
CBGD, CBAR, Black, NoAsign
Initial value SDI-IN2(Input Name)
Setting range SDI-IN1 to 4(Input Name), DVI-IN(Input Name), FMEM1, FMEM2,
CBGD, CBAR, Black, NoAsign
Initial value SDI-IN3(Input Name)
Setting range SDI-IN1 to 4(Input Name), DVI-IN(Input Name), FMEM1, FMEM2,
CBGD, CBAR, Black, NoAsign
Initial value SDI-IN4(Input Name)
78
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Setting menu tables
No.
Sub menu
Setting item
Setting
9 XPT SW Assign Menu
5 XPT5
6 XPT6
7 XPT7
8 XPT8
9 XPT9
10 XPT10
1 SDI-
Setting range SDI-IN1 to 4(Input Name), DVI-IN(Input Name), FMEM1, FMEM2,
CBGD, CBAR, Black, NoAsign
Initial value DVI-D(Input Name)
Setting range SDI-IN1 to 4(Input Name), DVI-IN(Input Name), FMEM1, FMEM2,
CBGD, CBAR, Black, NoAsign
Initial value FMEM1
Setting range SDI-IN1 to 4(Input Name), DVI-IN(Input Name), FMEM1, FMEM2,
CBGD, CBAR, Black, NoAsign
Initial value FMEM2
Setting range SDI-IN1 to 4(Input Name), DVI-IN(Input Name), FMEM1, FMEM2,
CBGD, CBAR, Black, NoAsign
Initial value CBGD
Setting range SDI-IN1 to 4(Input Name), DVI-IN(Input Name), FMEM1, FMEM2,
CBGD, CBAR, Black, NoAsign
Initial value CBAR
Setting range SDI-IN1 to 4(Input Name), DVI-IN(Input Name), FMEM1, FMEM2,
CBGD, CBAR, Black, NoAsign
Initial value Black
Setting range
10 Input Menu
IN1(Input Name)
2 SDI-
IN2(Input Name)
3 SDI-
IN3(Input Name)
4 SDI-
IN4(Input Name)
Initial value
Setting range
Initial value
Setting range
Initial value
Setting range
Initial value
5 DVI-IN(Input Name) Setting range
Initial value
10.1 Input Menu/SDI-
IN1(xxxxxx)
1 Mode
Setting range Normal, DbyD, AUTO
Initial value Normal
2 Freeze Select
3 Freeze
Setting range Frame, Field
Initial value Frame
Setting range On, Off
Initial value Off
4 Name Type
5 Name
Setting range Default, Preset, User, CAM Name
Initial value Default
Setting range Max. 10 characters can be set
Initial value
6 VPrc/YGain/Ped
7 VPrc:CGain/Hue
1 Mode
Setting range
Initial value
Setting range
Initial value
Setting range Normal, DbyD, AUTO
Initial value Normal
On, Off
Off
0.0 to 200.0
100.0
0.0 to 200.0
100.0
0.0 to 359.9
0.0
–20.0 to 20.0
0.0
V
C
Y
H
P
10.2 Input Menu/SDI-
IN2(xxxxxx)
2 Freeze Select
3 Freeze
Setting range Frame, Field
Initial value Frame
Setting range On, Off
Initial value Off
4 Name Type
5 Name
Setting range Default, Preset, User, CAM Name
Initial value Default
Setting range Max. 10 characters can be set
Initial value
6 VPrc/YGain/Ped
7 VPrc:CGain/Hue
Setting range
Initial value
Setting range
Initial value
On, Off
Off
0.0 to 200.0
100.0
0.0 to 200.0
100.0
0.0 to 359.9
0.0
–20.0 to 20.0
0.0
V
C
Y
H
P
79
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Setting menu tables
No.
Sub menu
Setting item
Setting
10.3 Input Menu/SDI-
IN3(xxxxxx)
1 Mode
Setting range Normal, DbyD, UC, AUTO
Initial value Normal
2 Freeze Select
3 Freeze
Setting range Frame, Field
Initial value Frame
Setting range On, Off
Initial value Off
4 Name Type
5 Name
Setting range Default, Preset, User, CAM Name
Initial value Default
Setting range Max. 10 characters can be set
Initial value
6 VPrc/YGain/Ped
7 VPrc:CGain/Hue
8 UC:Scale/ECPos
9 UC:Size
Setting range
Initial value
Setting range
Initial value
Setting range
Initial value
Setting range
Initial value
Setting range
Initial value
On, Off
Off
0.0 to 200.0
100.0
SQ, EC, LB
SQ
100 to 110
100
0.0 to 200.0
100.0
0.0 to 359.9
0.0
Center, Right, Left
Center
–20.0 to 20.0
0.0
V
C
S
S
M
Y
H
E
P
10 UC:Mvdet/Sharp
1 Mode
1 to 5
3
1 to 5
3
S
10.4 Input Menu/SDI-
IN4(xxxxxx)
Setting range Normal, DbyD, UC, AUTO
Initial value Normal
2 Freeze Select
3 Freeze
Setting range Frame, Field
Initial value Frame
Setting range On, Off
Initial value Off
4 Name Type
5 Name
Setting range Default, Preset, User, CAM Name
Initial value Default
Setting range Max. 10 characters can be set
Initial value
6 VPrc/YGain/Ped
7 VPrc:CGain/Hue
8 UC:Scale/ECPos
9 UC:Size
Setting range
Initial value
Setting range
Initial value
Setting range
Initial value
Setting range
Initial value
Setting range
Initial value
On, Off
Off
0.0 to 200.0
100.0
SQ,EC,LB
SQ
100 to 110
100
0.0 to 200.0
100.0
0.0 to 359.9
0.0
Center, Right, Left
Center
–20.0 to 20.0
0.0
V
C
S
S
M
Y
H
E
P
10 UC:Mvdet/Sharp
1 Freeze
1 to 5
3
1 to 5
3
S
10.5 Input Menu/DVI-IN(xxxxxx)
Setting range On, Off
Initial value Off
2 Name Type
3 Name
Setting range Default, Preset, User, CAM Name
Initial value Default
Setting range
Initial value
4 Scale
Setting range Fit-V, Fit-H, Full
Initial value Fit-V
Setting range xxxx*xxxx
Initial value
5 Size
6 H-Freq
Setting range XXHz
Initial value
7 V-Freq
Setting range XXHz
Initial value
8 Dot Clock
Setting range XXX.XXMHz
Initial value
80
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Setting menu tables
No.
Sub menu
Setting item
Setting
11 Output Menu
1 SDI-OUT1 Setting range PGM, PVW, CLN, AUX, MV, KeyOut
Initial value PGM
2 SDI-OUT2
Setting range PGM, PVW, CLN, AUX, MV, KeyOut
Initial value PVW
3 DVI-OUT
Setting range PGM, PVW, CLN, AUX, MV, KeyOut
Initial value AUX
4 SDI-OUT:Limit
5 DVI-OUT:Size
Setting range Off, 108, 104, 100
Initial value Off
Auto, XGA, WXGA, SXGA, WSXGA+, UXGA, WUXGA, 1080/59.94p,
Setting range
1080/50p
Initial value Auto
6 DVI-OUT:Scale
7 DVI-OUT:Mvdet
1 USER1
Setting range Fit-V, Fit-H, Full
Initial value Fit-V
Setting range 1 to 5
Initial value
3
12 USER/FMEM Menu
Setting range PinP Preset, WIPE Preset, PinPPVW, KeyPVW, GPI Input,
GPI Output, CamCont Link, AUX Transition, PinP Transition,
EFFDSLV Time, StrFMEM1, StrFMEM2, No Asign
Initial value PinP Preset
2 USER2
3 USER3
4 USER4
Setting range PinPPVW, KeyPVW, GPI Input, GPI Output, CamCont Link,
AUX Transition, PinP Transition, EFFDSLV Time, StrFMEM1,
StrFMEM2, No Asign
Initial value
—
Setting range PinPPVW, KeyPVW, GPI Input, GPI Output, CamCont Link,
AUX Transition, PinP Transition, EFFDSLV Time, StrFMEM1,
StrFMEM2, No Asign
Initial value
—
Setting range PinPPVW, KeyPVW, GPI Input, GPI Output, CamCont Link,
AUX Transition, PinP Transition, EFFDSLV Time, StrFMEM1,
StrFMEM2, No Asign
Initial value
—
5 FMEM Select
6 AUX to FMEM
7 FMEM Mode
1 OSD OUT
Setting range FMEM1, FMEM2
Initial value FMEM1
Setting range
Initial value
Setting range
Initial value
On, Off
Off
AUTO, Manual
AUTO
On
On
On
On
Rv
M
EX
EX
13 Operation Menu
Setting range SDI-OUT2, DVI-OUT, SDI-OUT2+DVI-D
Initial value SDI-OUT2+DVI-D
Setting range Full, Upper-Left, Upper-Right, Lower-Right, Lower-Left
Initial value Full
2 OSD Size
3 OSD Back
4 Key Priority
5 BUS Mode
6 Time Unit
Setting range On, Off
Initial value On
Setting range PinP over KEY, KEY over PinP
Initial value PinP over KEY
Setting range A/B, PGM(A)/PST(B), PGM(B)/PST(A)
Initial value PGM(A)/PST(B)
Setting range Sec, Frame
Initial value Sec
7 Slide Lever
8 GPI Input
Setting range BKGD, Key, PinP, NoAsign
Initial value BKGD
Setting range Enable, Disable
Initial value Enable
9 GPI Output
10 CamCont Link
Setting range Enable, Disable
Initial value Enable
Setting range On, Off
Initial value Off
81
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Setting menu tables
No.
Sub menu
Setting item
Setting range Alarm, NoAlarm
Initial value
Setting range Alarm, NoAlarm
Initial value
Setting range Alarm, NoAlarm
Initial value
Setting
13 Operation Menu
11 FAN
—
12 Power
—
13 Temperature
14 SYSTEM Menu
1 Format
—
Setting range UnLocked, Locked
Initial value UnLocked
14 SYSTEM Menu
1080/59.94i, 1080/50i, 1080/24psf, 1080/23.98psf, 720/59.94p,
720/50p, 480/59.94i, 576/50i
Setting range
Initial value 1080/59.94i
Setting range On, Off
Initial value Off
Setting range On, Off
Initial value Off
2 HiResMV
3 16:9SQ
4 AUX Anci
Setting range On, Off
Initial value Off
5 PGM Anci
6 PVW Anci
7 MV Anci
Setting range On, Off
Initial value Off
Setting range On, Off
Initial value Off
Setting range PGM, PVW, Off
Initial value Off
8 Initial
Setting range On, Off
Initial value Off
9 IP Address
10 Subnet Mask
11 GateWay
12 MAC Address
1 SYSTEM Ver.
2 SOFT Ver.
3 GLUE FPGA Ver.
4 MAIN FPGA Ver.
5 FONT Ver.
Setting range —
Initial value 192.168.0.30
Setting range —
Initial value 255.255.255.0
Setting range —
Initial value 192.168.0.1
Setting range
Initial value
Setting range Vxx.xx.xx
Initial value
Setting range Vxx.xx.xx
Initial value
Setting range Vxx.xx.xx
Initial value
15 SYSTEM Status
Setting range Vxx.xx.xx
Initial value
Setting range Vxx.xx.xx
Initial value
82
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Setting menu tables
No.
Sub menu
Setting item
Setting
BUS Asign Status
1 XPT SW
Setting range
Initial value
Setting range
Initial value
Setting range
Initial value
Setting range
Initial value
Setting range
Initial value
Setting range
Initial value
Setting range
Initial value
Setting range
Initial value
2 XPT SW Asign
3 PGM
4 PVW
5 AUX
6 PinP
7 Key-F
8 Key-S
83
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Appearance
Unit: mm (inch)
189 (7-7/16)
S V N M
B O O T
D V I I N
4
D V I O U T
T A L L Y / G P I
L A N
2
I N
1 2 V
1
3
2
1
S D I I N
S D I O U T
O N
1
4
2
3
P O W E R
S I G N A L G N D
65 (2-9/16)
Compact Live Switcher AW-HS50
POWER
AUX
ALARM
LINK
USER 1
3
USER 2
4
SHIFT
OSD/TIME
KEY ON
OSD ON
PinP
KEY-F/S
MIX
TRANSITION TYPE
WIPE
PinP ON
FTB ON
BUS DELEGATION
KEY-S
AUX
A
SHIFT
PGM
PVW
KEY OUT
CLN
MV
CUT
1
6
2
7
3
8
4
9
5 10
KEY-F
PinP
B
AUX
SHIFT
AUTO
BKGD
51 (2)
210 (8-1/4)
84
Download from Www.Somanuals.com. All Manuals Search And Download.
11. Specifications
Inputs
5 video lines
SDI 4 signal lines: SDI IN 1 to SDI IN 4
DVI-D 1 signal line: DVI IN
Outputs
3 video lines, 4 outputs
SDI 2 signal lines: SDI OUT 1, SDI OUT 2 (Only the SDI OUT 1 signals are split into two)
DVI-D 1 signal line: DVI OUT
Signal formats
SD
HD
480/59.94i, 576/50i
1080/59.94i, 1080/50i, 720/59.94p, 720/50p, 1080/24PsF, 1080/23.98PsF
Signal processing
Y:Cb:Cr 4:2:2, 10 bit (8 bits for frame memory)
RGB 4:4:4 8 bit
ME number
SDI inputs
1ME
HD: Serial digital component (SMPTE 292M)
SD: Serial digital component (SMPTE 259M)
4 signal lines: SDI IN 1 to SDI IN 4
HD: SMPTE 292M (BTA S-004B) standard complied with
• 0.8 V [p-p] ꢆ10 % (75 ꢇ)
• Input return loss
More than 15 dB (5 MHz to 1.5 GHz)
• Automatic equalizer 100 m (328 ft.) (when 5C-FB cable is used)
SD: SMPTE 259M standard complied with
• 0.8 V [p-p] ꢆ10 % (75 ꢇ)
• Input return loss
More than 15 dB (5 MHz to 270 MHz)
• Automatic equalizer 200 m (656 ft.) (when 5C-2V cable is used)
DVI-D input
SDI outputs
Digital RGB (Vertical frequency: 60 Hz):
XGA (1024ꢃ768), WXGA (1280ꢃ768), SXGA (1280ꢃ1024), WSXGA+ (1680ꢃ1050), UXGA
(1600ꢃ1200), WUXGA (1920ꢃ1200)
Digital RGB: 1080/50P, 1080/59.94P
ꢂꢁ Analog input signals are not supported.
HD: Serial digital component (SMPTE 292M)
SD: Serial digital component (SMPTE 259M)
2 signal lines: SDI OUT 1, SDI OUT 2 (Only the SDI OUT 1 signals are split into two)
HD: SMPTE 292M (BTA S-004B) standard complied with
• Output return loss
• Output level
• Rise time
More than 15 dB (5 MHz to 1.5 GHz)
0.8 V [p-p] ꢆ10 % (75 ꢇ)
Less than 270 ps
• Fall time
Less than 270 ps
• Difference between rise time and fall time
Less than 100 ps
• Alignment jitter
• Timing jitter
• Eye aperture ratio
• DC offset
Less than 0.2 UI (130 ps)
Less than 1.0 UI
More than 90 %
0 ꢆ0.5 V
SD: SMPTE 259M standard complied with
• Output return loss
• Output level
• Rise time
More than 15 dB (5 MHz to 270 MHz)
0.8 V [p-p] ꢆ10 % (75 ꢇ)
Less than 1.5 ns
• Fall time
Less than 1.5 ns
• Difference between rise time and fall time
Less than 0.5 ns
• Jitter
Less than 0.2 UI
85
Download from Www.Somanuals.com. All Manuals Search And Download.
11. Specifications
DVI-D output
Digital RGB (Vertical frequency: 60 Hz):
XGA (1024ꢃ768), WXGA (1280ꢃ768), SXGA (1280ꢃ1024), WSXGA+ (1680ꢃ1050), UXGA
(1600ꢃ1200), WUXGA (1920ꢃ1200)
Digital RGB: 1080/50P, 1080/59.94P
ꢂꢁ High-resolution multi view mode supported:
Signals are also output with a high resolution even when SD has been selected as the system
mode.
When the high-resolution multi view mode is enabled, MV is assigned to the DVI OUT
connector, and MV cannot be assigned to the SDI OUT 1 connectors or SDI OUT 2
connector
ꢂꢁ Analog output signals are not supported.
Video delay time
Control I/O
1 frame (F)
ꢂꢁ Video signals that have passed through the PinP, multi view display, DVI-D input or DVI-D
output will be delayed in each case by up to one frame.
LAN (RJ45)
Connecting cable:
10Base-T/100Base-TX
(For IP control)
LAN cable (category 5 or above), max. 100 m (328 ft.)
ꢂꢁ When connecting to a hub, use a straight cable.
Use a crossover cable when connecting the unit and
another device on a 1:1 basis without going through a hub.
TALLY/GPI
INPUT : 5 inputs, photocoupler sensing
(D-sub 15-pin, female, inch
thread)
OUTPUT : 7 outputs, open collector output (negative logic)
Other
SERVICE switch [SV/NM] (for maintenance purposes)
Normally, this switch is used as the “NM” position.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
11. Specifications
Ambient operating
temperature
0 °C to 40 °C (32 °F to 104 °F)
Humidity
10 % to 90 % (no condensation)
Power supply
DC 12 V, 2.5 A
ꢂꢁ Power consumption when using the AC adapter: AC 30 W
Supplied AC adapter
Rated input: AC 100 V to 240 V, 1.6 A, 47 to 63 Hz
Rated output: DC 12 V, 4.75 A, 57 W
Supplied power cord
Maximum rating: AC 125 V
ꢂ Use within AC 100 V to 120 V.
Dimensions
210 ꢃ 65 ꢃ 177 mm (8-1/4˝ ꢃ 2-9/16˝ ꢃ 6-15/16˝)
(W ꢈ H ꢈ D)
[excluding protrusions]
Weight
1.4 kg (3.08 lbs.)
ꢂꢁ The AC adapter and power cord provided must be used without fail.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix (glossary)
Defined below are the terms used in this manual.
Word
Explanation
AB Bus system
Ancillary Data
A bus control mode. By executing a transition, the A bus and B bus signals are
output to the program images alternately.
The auxiliary data other than the video signals which is transmitted inside the data
stream of the video serial interface. The data superimposed on the vertical blanking
period is referred to as the V ancillary data (VANC).
Aspect ratio
The ratio between the horizontal and vertical dimensions of an image or screen.
It is 16:9 for the HD format and 4:3 for the SD format.
AUX
[Auxiliary Bus]
A spare bus which can be switched by signals other than the main line output
signals.
AVDL
A function to automatically adjust the input image signal phase to the horizontal
synchronization reference signal phase.
[Automatic Video Delayline]
BB
The black burst signal. A full-screen black level composite signal which is used as
the reference signal for gen-lock.
[Black burst]
Border
The area or margin that is added to the edge of a wipe or key.
Its width and color can be adjusted. The defocusing of the area around a border is
referred to as the soft effect.
Chroma key
Clip
This refers to the function for creating the key signals based on the color information
of the video signals and combining the keys.
The threshold level of the luminance when key signals are created from a key
source.
Color Background
The signals which are output from the internal color generator and used as the
background image.
Cut
This refers to the effect where the display is instantly switched to the next image.
A parameter which is used to adjust the density of the key signals.
Density
Dot by Dot
This treats images as actual size (1ꢃ) images. With PinP, it allows SD images to
be combined with HD images with no accompanying deterioration in the images
themselves.
Down Converter
This is the function that converts material in the HD format into the SD format.
DSK [Downstream Key]
This refers to the key combination process which is performed at the end of the mix
effect. The key is always combined with the foremost image.
DVE [Digital Video Effect]
This refers to the transition patterns accompanying size reductions or slide effects.
DVI
A digital video interface standard.
[Digital Visual Interface]
DVI-I can handle both digital signals and analog signals.
Embedded Audio
This refers to the audio data packets which are transferred inside the data stream of
the video serial interface.
Flip Flop system
(PGM/PST system)
A bus control mode. The signals selected by the program bus are always output
as the program images. By executing a transition, the program bus and preset bus
signals are switched over.
Flying Key
This function uses DVE effects to move, expand or reduce key signals.
A memory which can hold the video signals equivalent to one frame.
Frame Memory
Frame Synchronizer
A function which matches the synchronization of non-synchronized video input
signals.
Freeze
A function which continues the display of the same image, creating the impression
that the image has been “frozen”.
FTB [Fade to Black]
Genlock
This is the effect where the background image is faded out to the black screen.
A function for synchronizing the video signals using an external sync signal as the
reference.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix (glossary)
Word
Explanation
GPI
Interface signals which control auto transition from an external source.
[General Purpose Interface]
Hue
IRE
The color tone of the video signals.
A unit used for video signal levels.
The setup level (black level) of the signals is expressed as 0 IRE, 7.5 IRE, etc.
Key Edge
Key Fill
The border or shadow added to the edges of keys.
The signal that uses key combination processing to fill in the areas left blank by the
key signals.
Key Gain
Key Invert
Key Mask
A parameter which is used to adjust the amplitude of the key signals.
A function which inverts the key signals.
This is the function that specifies the area for key combination using the box pattern,
etc. When only part of the area of the key signals is used, key combination is
executed with the unnecessary area masked.
Key Source
Linear Key
The video signals for creating the key signals.
The function which combines keys using monochrome key signals with gradations in
its outlines as a reference.
Lum
The brightness portion of the video signals.
[Luminance]
Luminance Key
The function which creates key signals based on the luminance (brightness)
information of the video signals to combine keys.
ME
[Mix Effect]
A video effect device which combines a number of video signals to create mix, wipe,
key and other video signals.
Mix
The picture-changing effect produced by overlapping one image with the next.
It is also referred to as “dissolve”.
Multi View Display
OSD [On Screen Display]
PinP [Picture in Picture]
This function combines multiple materials and displays them on one screen. PGM,
PVW and the input material can be previewed at the same time on a single screen.
This function enables settings to be performed on the menu screens which are
displayed in the monitor output.
This function combines a sub screen image with the background image.
PVW
[Preview]
The function for checking ahead of time the image which will be output after the next
transition. The image is output from the PVW system.
PGM
The bus which always carries the program output signals.
[Program Bus]
PST
[Preset Bus]
The bus which carries the program output signals after the next background
transition.
RS-422
A serial interface standard. It is the interface used to control the switcher from an
editor or other external device.
Sat
This refers to the intensity of the color chrominance level of video signals.
[Saturation]
SDI
The standard by which video signals in various SD and HD formats are transmitted
along a single coaxial cable.
[Serial Digital Interface]
Self Key
A function that creates key signals from key fill signals for combining keys.
Setup Data
The memory in which the control panel statuses can be saved and recalled.
The button selection statuses as well as the border, color and other setting
information can be saved in this memory.
89
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix (glossary)
Word
Explanation
Tally
The signal which outputs the program output statuses of the input signals to an
external device. The LED that indicates the program output status on the control
panel is also referred to as tally.
Transition
A function that switches from one image to another.
Wipe, mix and other effects are available for the images during switching.
Tri-level Sync
Trimming
The sync signal used for HD formats.
This is the function that eliminates the unnecessary parts at the top, bottom, left and/
or right of the images which are combined using the PinP function.
Up Converter
Wipe
This is the function that converts material in the SD format into the HD format which
yields a high resolution.
A video effect in which one image is gradually replaced by another as the boundary
between the two is moved using a preselected pattern.
90
Download from Www.Somanuals.com. All Manuals Search And Download.
© Panasonic System Networks Co., Ltd. 2010
D
F0410Y0
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions <Basics>
Compact Live Switcher
Model No.
AW-HS50N
Before operating this product, please read the instructions carefully and save this manual for
future use.
For instructions on how to operate this Compact Live Switcher and how
to establish its settings, refer to the “Operations and Settings” manual
(PDF file) which can be found on the CD-ROM supplied with the camera.
3TR006512BAA
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety precautions
CAUTION:
CAUTION
TO REDUCE THE RISK OF FIRE OR SHOCK
HAZARD AND ANNOYING INTERFERENCE,
USE THE RECOMMENDED ACCESSORIES
ONLY.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL.
FCC Note:
This equipment has been tested and found
to comply with the limits for a class A digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference when
the equipment is operated in a commercial
environment. This equipment generates, uses,
and can radiate radio frequency energy, and
if not installed and used in accordance with
the instruction manual, may cause harmful
interference to radio communications. Operation
of this equipment in a residential area is likely to
cause harmful interference in which case the user
will be required to correct the interference at his
own expense.
The lightning flash with arrowhead
symbol, within an equilateral triangle, is
intended to alert the user to the presence
of uninsulated “dangerous voltage” within
the product’s enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (service) instructions in the
literature accompanying the appliance.
WARNING:
THIS APPARATUS MUST BE EARTHED
To ensure safe operation, the three-pin plug must
be inserted only into a standard three-pin power
point which is effectively earthed through the
normal household wiring.
Warning:
To assure continued FCC emission limit
compliance, the user must use only shielded
interface cables when connecting to external
units.
Also, any unauthorized changes or
Extension cords used with the apparatus must
have three cores and be correctly wired to
provide connection to the earth. Wrongly wired
extension cords are a major cause of fatalities.
The fact that the apparatus operates satisfactorily
does not imply that the power point is earthed or
that the installation is completely safe. For your
safety, if you are in any doubt about the effective
earthing of the power point, please consult a
qualified electrician.
modifications to this equipment could void the
user’s authority to operate it.
CAUTION:
In order to maintain adequate ventilation, do
not install or place this unit in a bookcase,
built-in cabinet or any other confined space.
To prevent risk of electric shock or fire hazard
due to overheating, ensure that curtains
and any other materials do not obstruct the
ventilation.
For CANADA
This class A digital apparatus complies
with Canadian ICES-003.
Cet appareil numérique de la classe A est
conforme à la norme NMB-003 du Canada.
The socket outlet shall be installed near the
equipment and easily accessible or the mains
plug or an appliance coupler shall remain readily
operable.
WARNING:
• TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPARATUS TO RAIN OR MOISTURE.
A warning that an apparatus with CLASS 1
construction shall be connected to a MAINS
socket outlet with a protective earthing connection.
• THE APPARATUS SHALL NOT BE EXPOSED
TO DRIPPING OR SPLASHING AND THAT
NO OBJECTS FILLED WITH LIQUIDS, SUCH
AS VASES, SHALL BE PLACED ON THE
APPARATUS.
indicates safety information.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety precautions
IMPORTANT SAFETY INSTRUCTIONS
Read these operating instructions carefully before using the unit. Follow the safety instructions on the
unit and the applicable safety instructions listed below. Keep these operating instructions handy for
future reference.
1) Read these instructions.
10) Protect the power cord form being walked
on or pinched particularly at plugs,
convenience receptacles, and the point
where they exit from the apparatus.
2) Keep these instructions.
3) Heed all warnings.
11) Only
use
attachments/accessories
4) Follow all instructions.
specified by the manufacturer.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings.
12) Use only with the cart, stand,
tripod, bracket, or table
specified by the manufacturer,
or sold with the apparatus.
When a cart is used, use
caution when moving the cart/
apparatus combination to
avoid injury from tip-over.
Install
in
accordance
with
the
manufacturer’s instructions.
8) Do not install near any heat sources such
as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that
produce heat.
13) Unplug this apparatus during lightning
storms or when unused for long periods of
time.
9) Do not defeat the safety purpose of
the polarized or grounding-type plug.
A polarized plug has two blades with one
wider than the other. A grounding-type
plug has two blades and a third grounding
prong. The wide blade or the third prong
are provided for your safety. If the provided
plug does not fit into your outlet, consult an
electrician for replacement of the obsolete
outlet.
14) Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power-supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or has
been dropped.
indicates safety information.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
2. Preparations................................................18
Before use.........................................................5
Overview ..........................................................................5
Concerning the Operating Instructions ............................5
Trademarks and registered trademarks ...........................5
About copyright and licence.............................................5
Concerning the ratings display.........................................5
Disclaimer of warranty......................................................6
Network security...............................................................6
2-1. Installation precautions ...........................................18
2-2. Connections with other devices...............................19
2-2-1. Block diagram...................................................19
2-2-2. Example of connections...................................20
2-3. Turning the unit’s power on and off..........................22
2-4. Checking the video output.......................................22
2-4-1. Displaying the OSD menus on a PC monitor...22
2-4-2. Displaying the OSD menus
on an SDI monitor ............................................23
Characteristics..................................................7
Accessories ......................................................9
Required personal computer environment.....9
Operating precautions ...................................10
2-5. OSD (on-screen display) menu operations .............24
2-5-1. Displaying and clearing the OSD menus .........24
2-5-2. How to forcibly display the OSD menus ...........24
2-5-3. Menu configuration and
moving between menus ...................................25
2-5-4. Operations using the submenus ......................26
1. Parts and their functions ...........................11
1-1. Control panel...........................................................11
1-2. Rear panel...............................................................16
2-5-5. Indications used in this
Operating Instructions......................................27
2-5-6. Direct operations using the USER buttons
and OSD/TIME dial ..........................................28
2-5-7. Menu delegation function.................................29
2-5-8. Bus status displays ..........................................29
3. Appearance.................................................30
4. Specifications .............................................31
How the model’s Operating Instructions manuals are
configured
The manual of this Compact Live Switcher (hereafter, “the unit”) is divided into two manuals: one is the
<Basics> (this manual), and the other is the <Operations and Settings> (CD-ROM).
Before installing the unit, be sure to read the <Basics> to ensure that the unit is installed correctly.
This manual explains how to install the unit, how to check the video outputs and how to perform the
OSD menu operations.
For details on how to operate the unit and select its settings, refer to the “Operating Instructions
<Operations and Settings>” (PDF file) on the CD-ROM supplied with the unit.
To read PDF files, you will need Adobe® Reader® which is available from Adobe Systems.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Before use
Overview
Trademarks and registered
This unit is a 1 ME digital video switcher which
supports a multiple number of HD and SD formats.
Despite its compact size, it comes with four SDI inputs,
one DVI-D input, two SDI outputs and one DVI-D
output.
trademarks
Microsoft, Windows, Windows Vista, Windows 7 and
Internet Explorer are either registered trademarks
or trademarks of Microsoft Corporation in the
United States and other countries.
Intel and Intel Core are trademarks or registered
trademarks of Intel Corporation in the United States
and other countries.
Adobe and Reader are either registered trademarks
or trademarks of Adobe Systems Incorporated in
the United States and/or other countries.
In addition to its background transition capabilities that
use the cut, mix and wipe functions, one keyer channel
and one PinP channel are provided to enable video
productions in a wide variety of forms.
Furthermore, using the multi view display settings,
the screen of a monitor can be split into a number
of sections to accommodate up to ten images,
enabling the number of monitors to be reduced and a
space-saving system to be configured at low cost.
By means of the IP connection, an operating
environment where the unit is tied in with the
AW-HE50 HD integrated camera and AW-RP50
remote camera controller is achieved.
Other names of companies and products contained
in these Operating Instructions may be trademarks
or registered trademarks of their respective owners.
About copyright and licence
Distributing, copying, disassembling, reverse
compiling, reverse engineering, and also exporting in
violation of export laws of the software provided with
this unit are expressly prohibited.
Concerning the Operating
Instructions
For the purposes of these instructions, AW-HS50N
is referred to as “AW-HS50”.
Concerning the ratings
Similarly, AW-HE50HN and AW-HE50SN are
referred as “AW-HE50,” and AW-RP50N is referred
to as “AW-RP50”.
display
The unit’s name, model number and electrical ratings
are indicated on its bottom panel.
In these instructions, the phrases “pan-tilt head and
camera combination” and “camera integrated with
a pan-tilt head” are both referred to collectively as
“remote camera” except in places where specific
equipment is mentioned.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Before use
Disclaimer of warranty
Network security
IN NO EVENT SHALL Panasonic System Networks
Co., Ltd. BE LIABLE TO ANY PARTY OR ANY
PERSON, EXCEPT FOR REPLACEMENT OR
REASONABLE MAINTENANCE OF THE PRODUCT,
FOR THE CASES, INCLUDING BUT NOT LIMITED
TO BELOW:
As you will use this unit connected to a network, your
attention is called to the following security risks.
Leakage or theft of information through this unit
Use of this unit for illegal operations by persons
with malicious intent
Interference with or stoppage of this unit by
persons with malicious intent
ANY DAMAGE AND LOSS, INCLUDING
WITHOUT LIMITATION, DIRECT OR INDIRECT,
SPECIAL, CONSEQUENTIAL OR EXEMPLARY,
ARISING OUT OF OR RELATING TO THE
PRODUCT;
It is your responsibility to take precautions such as
those described below to protect yourself against the
above network security risks.
PERSONAL INJURY OR ANY DAMAGE
CAUSED BY INAPPROPRIATE USE OR
NEGLIGENT OPERATION OF THE USER;
UNAUTHORIZED DISASSEMBLE, REPAIR OR
MODIFICATION OF THE PRODUCT BY THE
USER;
Use this unit in a network secured by a firewall, etc.
If this unit is connected to a network that includes
PCs, make sure that the system is not infected by
computer viruses or other malicious entities (using
a regularly updated antivirus program, anti-spyware
program, etc.).
INCONVENIENCE OR ANY LOSS ARISING
WHEN IMAGES ARE NOT DISPLAYED, DUE
TO ANY REASON OR CAUSE INCLUDING ANY
FAILURE OR PROBLEM OF THE PRODUCT;
ANY PROBLEM, CONSEQUENTIAL
INCONVENIENCE, OR LOSS OR DAMAGE,
ARISING OUT OF THE SYSTEM COMBINED
BY THE DEVICES OF THIRD PARTY;
ANY INCONVENIENCE, DAMAGES OR
LOSSES RESULTING FROM ACCIDENTS
CAUSED BY AN INADEQUATE INSTALLATION
METHOD OR ANY FACTORS OTHER THAN A
DEFECT IN THE PRODUCT ITSELF;
LOSS OF REGISTERED DATA CAUSED BY
ANY FAILURE;
Refrain from connections that use public lines.
ANY DAMAGES, CLAIMS, ETC. DUE TO
LOSS OR LEAKAGE OF IMAGE DATA OR
SETTING DATA SAVED ON THIS UNIT OR IN A
PERSONAL COMPUTER.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Characteristics
Compact design
Multi view display function
The unit features a compact design with its half-
rack size width (210 mm [8-1/4˝]) and its 4RU size
(177 mm [6-15/16˝]) depth.
One channel is provided for the multi view display
function.
The user can select whether the screen is to be
split into 10, 9, 6, 5 or 4 sections.
On each split screen, the user can assign PGM,
PVW, AUX or other materials in addition to input
materials.
The AW-RP50 remote camera controller (option)
also has the same size. When it is placed alongside
the unit, the two units are housed in the full rack
width.
Multiple formats supported
Many different effect functions provided
The unit enables the user to select wipe or mix as
the type of background transition.
A 1-channel keyer function is provided. The user
can select linear keys, luminance keys or chroma
keys as the key type.
The signal formats supported by the unit
include both HD formats (1080/59.94i, 1080/50i,
1080/24PsF, 1080/23.98PsF, 720/59.94p and
720/50p) and SD formats (480/59.94i and 576/50i).
One PinP channel and one AUX bus system are
available.
Five input systems and three output systems
featured
The unit comes with four SDI input connectors
(SDI IN 1 to SDI IN 4) and one DVI-D input
connector (DVI IN).
The user can choose not only cut transitions
but also mix transitions as the effect yielded for
switching materials using the PinP bus and AUX
bus. (Bus transition function)
It also comes with two SDI output connectors
(SDI OUT 1 and SDI OUT 2) and one DVI-D output
connector (DVI OUT).
2-channel frame memory (8 bits)
The user can select the still images stored in the
frame memory as the bus material.
Frame synchronizer system
Still images can be transferred from the host
computer, which is connected to the unit via a LAN,
to the frame memories.
A frame synchronizer is incorporated for each of the
inputs so that asynchronous video signals can be
selected with no accompanying shocks.
Audio level meter display function
This function enables the level of the embedded
audio signals transferred by SDI input to be
displayed.
2-channel up-converter, 4-channel Dot by Dot
function and 4-channel video process function
An up-converter is incorporated in SDI IN 3 and
SDI IN 4.
A Dot by Dot function is incorporated for all the SDI
input connectors (SDI IN 1 to SDI IN 4).
By using this function and the PinP function
together, SD materials can be embedded in HD
images with no deterioration in the image quality.
The video process function is incorporated in all the
SDI input connectors (SDI IN 1 to SDI IN 4) to make
it possible to adjust the colors at the input stage of
the switcher.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Characteristics
Straightforward and flexible operability
The control panel layout includes a row of five
crosspoint buttons for the A bus and another row of
five crosspoint buttons for the B bus. Using these
buttons together with the SHIFT button enables a
total of ten images to be switched. Cut switches are
also made possible by the CUT button.
Separate buttons enable the PinP, KEY and FTB
functions to be turned ON or OFF in a single-step
action.
The slide lever is not only used to initiate
background transition operations but it can also
be allocated to execute PinP and KEY fade in/out
operations.
Two USER buttons located on control panel.
Using these buttons together with the SHIFT button
allows a total of four user settings (USER1 to
USER4) to be allocated.
Function for linkup with a remote camera
controller using IP connection
The unit can be connected to a Panasonic remote
camera controller using a network.
By linking it with a remote camera controller, it is
possible to put together a highly efficient operating
environment.
Supported remote camera controller:
AW-RP50
Only one switcher (the unit) can be linked with a
remote camera controller.
[Display of camera information]
The camera setting information (iris, gain and so
on) obtained by the AW-RP50 can be displayed
in the AUX output or on the split screens of multi
view display.
[Transmission of tally information]
The unit’s ON AIR tally information can be sent
to the AW-RP50.
PinP settings or WIPE pattern settings can be
allocated to the USER buttons.
[Switching of materials]
The bus materials of the switcher (the unit) can
On-screen display (OSD)
be selected from the AW-RP50.
The setting menus can be displayed on an external
monitor from the SDI OUT 2 and DVI OUT output
connectors.
They can be switched in tandem with the
selection of the camera using the AW-RP50.
(Control buses supported: AUX, PVW, PinP,
KEY-F)
(These menus cannot be displayed using the
SDI OUT 1 output connector.)
[Focus assist function]
By operating the buttons on the AW-RP50, it
is possible to switch to the multi view display
screen from the full screen display of the camera
images.
(Control bus supported: AUX)
[Parameter operation using PAN/TILT lever and
ZOOM button]
The PAN/TILT lever and ZOOM button on the
AW-RP50 can be used to change the parameters
of the switcher (the unit).
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
Check that the following accessories are present and accounted for.
Operating Instructions <Basics> (this manual) .......... 1
AC adapter ................................................................ 1
Power cable (2 m [6.6 ft.]) .......................................... 1
CD-ROM .................................................................... 1
Operating Instructions <Basics>
Operating Instructions <Operations and Settings>
Data Transmission Software
Required personal computer environment
Run the software that is provided with the switcher on a host computer which satisfies the following specifications.
CPU
Intel® CoreTM2 DUO 2.4 GHz or faster recommended
Memory
Windows® XP:
512 MB or more
Microsoft® Windows Vista®, Microsoft® Windows® 7:
1 GB or more
Network function
10BASE-T or 100BASE-TX
Image display
function
Resolution:
1024 768 pixels or more
Color generation: True Color (24 bits or more)
Supported operating
system
Microsoft® Windows® XP, Microsoft® Windows Vista®,
Microsoft® Windows®
7
Hard disk drive
Other
At least 50 MB of free memory
CD-ROM drive
(for using the Operating Instructions and various software)
Adobe® Reader®
(for browsing the Operating Instructions on the CD-ROM)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating precautions
In addition to heeding the points presented in the “Safety precautions”,
observe the following precautions as well.
Handle carefully.
Do not drop the product, or subject it to strong shock
or vibration.
Do not carry or move the product by the slide lever.
This is important to prevent trouble.
Precaution to be observed during production
This product’s image switching and image effect
functions can be used to produce images which flicker
rapidly or images which change rapidly.
However, bear in mind when using these functions
in production that the kinds of images produced
may have an adverse effect on the viewer’s physical
well-being.
Use the product in an ambient temperature of 0 °C
to +40 °C (32 °F to 104 °F).
Avoid using the product at a cold place below 0 °C
(32 °F) or at a hot place above +40 °C (104 °F)
because extremely low or high temperature will
adversely affect the parts inside.
When the product is to be discarded
When the product is to be discarded at the end of its
service life, ask a specialized contractor to dispose of
it properly in order to protect the environment.
Power off before connecting or disconnecting
cables.
Before plugging or unplugging the cables, be sure to
Concerning the consumable parts
Cooling fan:
switch power off.
This is a consumable part.
As a general rule, replace it every 5 years or so
(when the unit has been operated for 15 hours a
day).
Avoid humidity and dust.
Avoid using the product at a humid, dusty place
because much humidity and dust will cause damage to
the parts inside.
AC adapter:
This is a consumable part.
As a general rule, replace it every 5 years or so
(when the unit has been operated for 15 hours a
day).
Maintenance
Wipe the product using a dry cloth. To remove
stubborn dirt, dip a cloth into a diluted solution of
kitchen detergent (neutral), wring it out well, and wipe
the product gently.
The period when the consumable parts need to
be replaced will differ depending on the operating
conditions.
Then, after wiping the product with a moist cloth, wipe
it again with a dry cloth.
When the time comes to replace one of these
parts, be absolutely sure to ask your dealer to
do the job.
Caution
Avoid using benzine, paint thinners and other
volatile fluids.
If a chemical cleaning cloth is to be used,
carefully read through the precautions for its use.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Parts and their functions
1-1. Control panel
ꢀ
ꢁ
ꢂ ꢇ
ꢆ ꢅ
ꢈ
ꢉ
Compact Live Switcher AW-HS50
POWER
AUX
ALARM
LINK
USER 1
3
USER 2
4
SHIFT
OSD/TIME
KEY ON
OSD ON
FTB ON
ꢎ
ꢊ
ꢍ
ꢏ
PinP
KEY-F/S
MIX
TRANSITION TYPE
WIPE
PinP ON
BUS DELEGATION
KEY-S
AUX
A
ꢋ
ꢌ
ꢐ
ꢑ
SHIFT
PGM
PVW
KEY OUT
CLN
MV
5 10
CUT
1
6
2
7
3
8
4
9
KEY-F
PinP
AUX
B
SHIFT
AUTO
BKGD
ꢃ ꢄ
POWER indicator [POWER]
LINK indicator [LINK]
This indicator lights when the POWER switch
() on the rear panel is set to ON while power is
supplied to the DC IN connector ().
This indicator lights when the unit is linked on
a network with the AW-RP50 remote camera
controller available as an option.
The link setting must be enabled at both the unit
and AW-HS50.
ALARM indicator [ALARM]
This indicator lights when the cooling fan ()
has stopped running, when there is a problem
with the power supply (voltage drop) or when
the temperature inside the unit has reached an
abnormally high level.
When this occurs, an alarm message appears on
the OSD menu while the OSD menu is displayed on
an external monitor (in the OSD ON status).
The alarm information can be output to an external
device from the unit’s TALLY/GPI connector ().
Refer to “5-2. TALLY/GPI” (<Operations and
Settings> Operating Instructions).
When an alarm has occurred, stop using the unit
immediately, and be absolutely sure to contact your
dealer.
Continuing to use the unit even after an alarm has
occurred could damage the unit.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Parts and their functions
USER buttons [USER 1, USER 2]
Any four functions selected from among the menu
items can be assigned to the USER 1 button and
USER 2 button, and then used.
OSD/TIME dial [OSD/TIME]
The following operations are performed using this
dial.
When the main menu is displayed:
Turn the OSD/TIME dial to select a submenu,
and press the dial to enter the selection.
The functions registered in [USER1] and [USER3]
are assigned to the USER 1 button whereas the
functions registered in [USER2] and [USER4] are
assigned to the USER 2 button.
When a submenu is displayed:
Turn the OSD/TIME dial to select a setting item,
and press the dial to enter the selection.
When the dial is turned while a setting is
blinking, the setting changes, and when the dial
is pressed, the blinking part moves to the right.
When the dial is held down while a setting is
blinking, the setting is restored to default value.
(However, the network settings are not returned
to their default values.)
While the SHIFT button () is held down, the
function registered in [USER3] or [USER4] can be
selected.
Button indicator ON:
The functions assigned to the USER buttons
are enabled.
Button indicator OFF:
The functions assigned to the USER buttons
are disabled.
When the dial is turned while it is still held down
after the PinP ON, KEY ON, FTB ON or AUTO
button has been held down, the respective
transition duration can be changed.
When “[2] WIPE Menu”, “[3] PinP Menu” or “[5] KEY
Adjust Menu” is displayed on the OSD menu or
when the chroma key marker is in the ON status,
these buttons function as short-cut buttons for
specific setting items.
Refer to “1-8. Setting the USER buttons”
(<Operations and Settings> Operating
Instructions).
OSD ON button [OSD ON]
This selects whether the OSD menu is to be
displayed or hidden.
Each time the OSD ON button is held down, the
OSD menu is switched between displayed and
hidden.
SHIFT button [SHIFT]
Button indicator ON:
The OSD menu is displayed.
Button indicator OFF:
The OSD menu is hidden.
This is pressed to call the [USER3] and [USER4]
functions which have been assigned to the USER 1
button and USER 2 button or to call the XPT6 to
XPT10 materials which have been assigned to
crosspoint buttons [1] to [5].
Button indicator ON:
The SHIFT button is enabled.
Button indicator OFF:
The SHIFT button is disabled.
(The functions executed using the SHIFT
button take effect only while the button is held
down.)
PinP ON button [PinP ON]
This is used to combine PinP (picture-in-picture)
images for the transition duration which has been
set.
Press the button.
Blinks
Image combining is
now underway.
The button
indicator goes off.
Images can no
longer be combined.
Lights
Image combining
is now completed.
Lights
Image combining is
now disabled.
Press the button.
By turning the OSD/TIME dial () while keeping
the PinP ON button pressed after the button has
been held down, the transition duration can be
changed.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Parts and their functions
KEY ON button [KEY ON]
AUTO button [BKGD AUTO]
This is used to combine key materials for the
transition duration which has been set.
This automatically initiates the transition for the
transition duration which has been set. (Auto
transition)
Press the button.
Blinks
Button indicator ON:
Auto transition is being executed.
Button indicator OFF:
Auto transition is complete.
Image combining is
now underway.
The button
indicator goes off.
Images can no
Lights
Image combining
is now completed.
longer be combined.
If the AUTO button is pressed while auto transition
is being executed, the auto transition operation is
aborted.
When the button is pressed again after the
operation was aborted, the remaining transition is
executed.
When the AUTO button is pressed with the slide
lever () at a midway setting, the transition is
executed in the remaining time from the midway
status.
Lights
Image combining is
now disabled.
Press the button.
By turning the OSD/TIME dial () while keeping
the KEY ON button pressed after the button has
been held down, the transition duration can be
changed.
By turning the OSD/TIME dial () while keeping
the AUTO button pressed after the button has been
held down, the transition duration can be changed.
FTB ON button [FTB ON]
Press this button to fade out the program image to
a black screen for the transition duration which has
been set.
When the button is pressed again, the program
image is faded in from the black screen.
Slide lever
This is used when executing transitions manually.
When the slide lever is moved to the end, the
transition is completed.
Press the button.
Blinks
Now fading out.
If it has been moved while an auto transition was
being executed, operation will switch to manual as
soon as the position of the slide lever has gone
beyond the amount of the transition having been
executed.
The button
Lights
indicator goes off.
Program image
Fade-out is now
completed.
Lights
Now fading in.
Press the button.
It is possible to select a background, key or PinP
using a menu for materials involving transitions.
An image other than the black screen can be set
as the screen to which the program image is to be
faded out.
Refer to “1-5. FTB (fade to black)” (<Operations
and Settings> Operating Instructions).
By turning the OSD/TIME dial () while keeping
the FTB ON button pressed after the button has
been held down, the transition duration can be
changed.
CUT button [BKGD CUT]
This instantly initiates a transition for the currently
selected operation.
Button indicator ON:
The transition is being executed.
Button indicator OFF:
The transition is complete.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Parts and their functions
MIX button [MIX]
BUS DELEGATION buttons
This is used to execute transitions (MIX transitions)
while overlapping the images of the A bus and
B bus (or images of the PGM bus and PST bus).
While a transition is being executed, the total of
the A bus and B bus (or PGM bus and PST bus)
outputs is held at 100 %.
When the MIX button is pressed, its indicator lights
to show that this function is now selected.
If the WIPE button () is now pressed, the function
selection is released, and the indicator goes off.
Button indicator ON:
[AUX, PinP, KEY-F/S]
These are used to select the buses which output
the materials selected by the crosspoint buttons (,
).
Any of four lighting statuses are established: the
status in which the indicators of all of the three
buttons are off, and the statuses in which the
indicator of one of the buttons is blinked. (It is not
possible for the indicators of two of the buttons to
be blinked at the same time.)
When one of the buttons is pressed while
the indicators of all three buttons are off, the
indicator of the pressed button blinks.
When the button whose indicator is blinked is
pressed, its indicator is turned off.
A MIX transition is being selected.
WIPE button [WIPE]
This is used to execute transitions using the
selected wipe pattern.
When a button whose indicator is not blinked is
pressed, only the indicator of the pressed button
blinks.
When the WIPE button is pressed, its indicator
lights to show that this function is now selected.
If the MIX button () is now pressed, the function
selection is released, and the indicator goes off.
By turning the OSD/TIME dial () after the WIPE
button has been held down and while the button is
still pressed, the wipe pattern can be changed.
Button indicator ON:
The following operations can be undertaken in each
of these statuses.
1. When the indicators of all three buttons are
off:
In this status, the materials of the bus that
executes background transitions are selected.
Wipe selection underway
2. When the indicator of the AUX button is
blinked:
In this status, the AUX bus materials are
selected.
Bus tally indicators [A, B]
The indicator corresponding to the bus whose
program (PGM) materials are being output lights.
3. When the indicator of the PinP button is
blinked:
In this status, the PinP bus materials are
selected.
4. When the indicator of the KEY-F/S button is
blinked:
In this status, the key fill bus and key source bus
materials are selected.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Parts and their functions
2. When the indicator of the AUX button is
A bus crosspoint buttons [1 to 5]
B bus crosspoint buttons [1 to 5]
These are used to select the materials to be output
to the PGM bus, PST bus, AUX bus, PinP bus and
KEY-F/S bus.
blinked:
When one of the crosspoint buttons is pressed,
the AUX bus material is selected.
[B bus crosspoint buttons]
When a button is pressed and the material
allocated to that button is selected, the indicator of
the button lights.
When a button from [1] to [5] is pressed, the
material assigned to the corresponding XPT1
to XPT5 is selected.
When a button from [1] to [5] is pressed while
the SHIFT button is held down, the material
assigned to the corresponding XPT6 to XPT10
is selected.
Depending on the status of the BUS DELEGATION
button () indicators, the operation performed
differs as follows.
[A bus crosspoint buttons]
1. While the indicators of all three buttons are
off:
When a button from [1] to [5] is pressed,
PGM, PVW, KEY OUT, CLN or MV is selected
respectively.
When one of the crosspoint buttons is pressed,
the materials of the buses which execute the
background transitions are selected.
3. While the indicator of the PinP button is
blinked:
[B bus crosspoint buttons]
When a B crosspoint button is pressed, the PinP
These are used to select the PST bus
bus material is selected.
materials.
[B bus crosspoint buttons]
When a button from [1] to [5] is pressed, the
material assigned to the corresponding XPT1
to XPT5 is selected.
When a button from [1] to [5] is pressed while
the SHIFT button is held down, the material
assigned to the corresponding XPT6 to XPT10
is selected.
When a button from [1] to [5] is pressed, the
material assigned to the corresponding XPT1
to XPT5 is selected.
When a button from [1] to [5] is pressed while
the SHIFT button is held down, the material
assigned to the corresponding XPT6 to XPT10
is selected.
[A bus crosspoint buttons]
These are used to select the PGM bus
materials.
When a button from [1] to [5] is pressed, the
material assigned to the corresponding XPT1
to XPT5 is selected.
When a button from [1] to [5] is pressed while
the SHIFT button is held down, the material
assigned to the corresponding XPT6 to XPT10
is selected.
4. While the indicator of the KEY-F/S button is
blinked:
When one of the crosspoint buttons is pressed,
the key fill bus or key source bus material is
selected.
[B bus crosspoint buttons]
These are used to select the key fill bus
materials. When a button from [1] to [5]
is pressed, the material assigned to the
corresponding XPT1 to XPT5 is selected.
When a button from [1] to [5] is pressed while
the SHIFT button is held down, the material
assigned to the corresponding XPT6 to XPT10
is selected.
Memo
Using the OSD menu, A/B, PGM(A)/PST(B) or
PGM(B)/PST(A) can be selected as the bus mode.
The description given above applies when the
PGM(A)/PST(B) has been selected.
Refer to “1-1-4. Selecting the bus mode”
(<Operations and Settings> Operating
Instructions).
[A bus crosspoint buttons]
These are used to select the key source bus
materials.
When a button from [1] to [5] is pressed, the
material assigned to the corresponding XPT1
to XPT5 is selected.
When a button from [1] to [5] is pressed while
the SHIFT button is held down, the material
assigned to the corresponding XPT6 to XPT10
is selected.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Parts and their functions
1-2. Rear panel
ꢁ
"
$
ꢀ
SIGNAL GND
4
1
3
2
POWER
ON
SDI OUT
SDI IN
ꢃ
!
1
2
4
3
2
1
12 V IN
LAN
TALLY / GPI
DVI OUT
DVI IN
BOOT
SV NM
ꢆ
ꢅ
ꢄ
ꢂ #
SDI IN connectors [SDI IN 1 to 4]
These are the HD/SD SDI signal input connectors.
The following input modes can be set by menu
operations:
POWER switch [POWER]
When the POWER switch is set to the ON position,
the POWER indicator () lights, and the unit can
be operated.
SDI IN 1, 2: Normal, DbyD
SDI IN 3, 4: Normal, DbyD, UC, Auto
The video process function can be used for all the
SDI IN 1 to 4 input signals.
The up-converter cannot be used for SDI IN 1
and 2.
SDI OUT connectors [SDI OUT 1, 2]
These are the HD/SD SDI signal output connectors.
The following signals can be assigned to the
connector by menu operations:
When signals differing from the system format
have been input, they are replaced with black
signals.
PGM, PVW, CLN, AUX, MV, KEYOUT
At the SDI OUT 1 connector, the output signals
are split into two and output through two
connectors.
(However, when HD has been selected as the
system format setting and DbyD or UC has been
selected as the input mode setting, SD signals
with the same vertical frequency can be input.)
It is the same signal that is output.
The OSD menu, multi view display frame, tally
information, names of the materials and audio
level meters are not displayed for the signals of
the SDI OUT 1 connector.
When the high-resolution multi view mode is
enabled, it is not possible to assign MV signals.
DVI IN connector [DVI IN]
This is the DVI-D signal input connector.
Signals with the following resolution can be input to
this connector.
Digital RGB (vertical frequency: 60 Hz):
XGA (1024 768), WXGA (1280 768),
SXGA (1280 1024), WSXGA+ (1680 1050),
UXGA (1600 1200), WUXGA (1920 1200)
Digital RGB:
1920 1080/50p, 1920 1080/59.94p
Analog signals cannot be input to this connector.
A DVI-I cable cannot be used.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Parts and their functions
DVI OUT connector [DVI OUT]
TALLY/GPI connector [TALLY/GPI]
This is the DVI-D signal output connector.
Signals with the following resolution can be output
from this connector by menu operations.
(D-sub 15-pin, female, inch thread)
This connector features five contact input ports
for controlling the unit from an external device and
seven open collector output ports for outputting the
tally information and alarm information from the unit.
Digital RGB (vertical frequency: 60 Hz):
XGA (1024 768), WXGA (1280 768),
SXGA (1280 1024), WSXGA+ (1680 1050),
UXGA (1600 1200), WUXGA (1920 1200)
Cooling fan
Digital RGB:
1920 1080/50p, 1920 1080/59.94p
DC IN connector [12V
IN] (DC 12 V, 2.0 A)
Furthermore, the following signals can be assigned
by menu operations.
The AC adapter provided with the unit is connected
to this connector.
PGM, PVW, CLN, AUX, MV, KEYOUT
Ground terminal [SIGNAL GND]
The connector supports the high-resolution multi
view mode so that images can be output at a high
resolution when SD has been selected as the
system format.
Analog signals cannot be output from this
connector.
Connect this to the system’s ground.
SERVICE switch [SV/NM]
This switch is used for maintenance purposes.
For normal operations, select the “NM” position.
A DVI-I cable cannot be used.
When the high-resolution multi view mode
has been enabled, MV signals are assigned
to the DVI OUT connector, and they cannot
be assigned to the SDI OUT 1 connector or
SDI OUT 2 connector.
Wire fastening fitting
An anti-theft wire available on the market can be
fastened to this fitting to prevent theft.
LAN connector [LAN] (RJ-45)
(10BASE-T/100BASE-TX)
The remote camera, remote camera controller and
host computer supporting IP connections to this
LAN connector are connected using LAN cables.
When a device is connected directly to the unit, use
a crossover cable (category 5 or above).
When a device is to be connected to the unit
through a hub (switching hub), for instance, use a
straight cable (category 5 or above).
17
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Preparations
2-1. Installation precautions
In addition to heeding the points presented in the “Safety precautions”,
observe the following precautions as well.
Be absolutely sure to ask your dealer to do the jobs of installing and connecting the unit.
Connecting the power supply
Use within AC 100 V to 120 V.
Be absolutely sure to use only
the power cable and AC adapter
supplied with the unit.
The power cable supplied with
the unit has a 3-pin plug with a
grounding terminal.
Handle carefully!
Dropping the unit or subjecting it to strong impact or
vibration may cause trouble and/or malfunctioning.
Do not allow any foreign objects to enter
inside the unit!
Allowing water, metal items, scraps of food or other
foreign objects inside the unit may cause a fire and/
or electric shocks.
Connect it to a 3-pole outlet
which has been connected to
ground.
Choosing the best installation location
This unit is designed for indoor use only.
Install the unit on a sufficiently strong, stable and
level surface for use.
Ensure a space of at least 100 mm (3-15/16˝)
around the front and rear vents to avoid obstructing
ventilation.
Be absolutely sure to connect the ground terminal
(SIGNAL GND) at the rear of the unit to the system
ground.
Insert the DC plug as far as it will go until it locks
into position.
When the unit is not going to be used for a
prolonged period of time, turn off its power, and
disconnect the power plug from the AC outlet.
In particular, ensure sufficient space between
ventilation and wiring when using mounted in a
panel or table.
Do not install the unit in a manner in which its
cables and other accessories can be easily
damaged.
4
3
2
POWER
ON
1
Do not install the unit in a cold place where the
temperatures will drop below 0 °C (32 °F) or in a
hot place where the temperatures will rise above
+40 °C (104 °F).
1
SDI IN
2
IN
12V
3
BOOT
NM
SV
Avoid installing the unit where it will be exposed to
direct sunlight or to the hot air that is blown out from
other products.
Installing the unit in a very humid, dusty or
vibration-prone location may give rise to trouble.
Ventilation holes
18
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Preparations
2-2. Connections with other devices
2-2-1. Block diagram
AW-HS50
DbyD
FS
BLACK
SDI IN 1
SDI IN 2
SDI IN 3
SDI IN 4
SDI OUT 1
BKGD TRANS
VPrc
41, 42
(CUT, MIX, WIPE)
COLOR
BKGD
DbyD
FS
Output 1, 2
(SDI)
COLOR
BAR
VPrc
KEY
INPUT 1 to 4
(SDI)
(LIN, LUM, CHROMA)
OSD
DbyD
UC
FS
FMEM 1
FMEM 2
SDI OUT 2
OUT
MTX
MV
Frame
VPrc
PinP
FTB
AUX
DbyD
UC
FS
MV
Tally
VPrc
Src
Name
IN
MTX
Output 3
(DVI-D)
DVI OUT
Scaler
Audio
Level
Meter
INPUT 5
(DVI-D)
DVI IN
Scaler
MULTI VIEW
FS
Power
TALLY/GPI
(D-sub, 15-pin)
LAN
(RJ45)
DC IN
12 V
43
[Output, 7 pin]
(1) TALLY OUT 1
(2) TALLY OUT 2
(3) TALLY OUT 3
(4) TALLY OUT 4
(5) TALLY OUT 5
(6) ALARM
[Input, 5 pin]
(10) TALLY DISABLE
(11) AUTO
(12) CUT
(13) KEY ON
(14) PinP ON
44
Hub
AC adapter
Power cable
AW-RP50
45
(7) KEY ON
(15) GND
45
AW-HE50
45
PC
1: At the SDI OUT 1 connector, the output signals are split into two and output through two connectors.
2: The setting menus (OSD), multi view display frame, tally information, names of the materials and audio
level meters are not displayed for the signals of the SDI OUT 1 connectors.
3: Use a crossover cable when connecting the unit and another device on a 1:1 basis without going through
a hub (switching hub).
4: Use a switching hub.
5: Communication over the internet is not possible.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Preparations
2-2-2. Example of connections
HD SDI
HD camera
HD SDI
42
SDI monitor
HD SDI
HD SDI
HD camera
42
VTR
HD SDI
HD camera
HD SDI
SD SDI
SDI monitor
PC monitor
SD camera
DVI-D
44
DVI-D
43
PC
41
SIGNAL GND
4
1
3
2
POWER
ON
SDI OUT
SDI IN
1
2
4
3
2
1
12 V IN
LAN
TALLY / GPI
DVI OUT
DVI IN
BOOT
SV NM
AC adapter
Compact Live Switcher
AW-HS50
Power cable
1: The up-converter works only with the SDI IN 3 and SDI IN 4 inputs.
(The Dot by Dot mode works with all four SDI IN 1 to 4 inputs.)
2: The two signals which are output from the SDI OUT 1 connectors are identical.
The OSD menus, multi view display frame, tally information, names of the materials and audio level
meters are not displayed for the signals of these connectors.
3: Analog signal input is not supported.
4: Analog signal output is not supported.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Preparations
Example of IP connections
(connecting the unit to the AW-HE50 and AW-RP50)
AW-HE50S
AW-HE50S
LAN cable
(straight cable)
SDI video signal
Monitor 2
Monitor 1
Switching hub
LAN cable
(straight cable)
Monitor
Monitor
AW-HS50
AW-RP50
21
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Preparations
2-3. Turning the unit’s power on
and off
2-4. Checking the video output
Described below are the steps taken to display the
unit’s OSD menu on an external monitor to check the
unit’s video output.
Turning on the power
2-4-1. Displaying the OSD menus on a
PC monitor
1
Set the POWER switch to the ON position.
When power is supplied to the unit, the POWER
indicator lights up green.
1
Connect the PC monitor to the unit’s
DVI OUT connector.
Turning off the power
2
3
4
Turn on the power of the PC monitor.
Turn on the power of the unit.
1
Set the POWER switch to the OFF
position.
The unit’s power is turned off, and the POWER
indicator goes off.
Hold down the OSD ON button.
The OSD ON button indicator lights, and the OSD
menus are displayed on the PC monitor.
If the OSD menus do not appear on the monitor,
refer to “2-5-2. How to forcibly display the OSD
menus”.
Note
If the OSD menu fails to appear on the PC monitor
even after the above steps have been taken, it may
mean that the PC monitor does not support the
unit’s DVI output format.
Check the input specifications of the PC monitor.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Preparations
2-4-2. Displaying the OSD menus on
an SDI monitor
Changing the video format
If the OSD menus cannot be displayed even when the
SDI monitor has been connected to the unit, the video
format must be changed.
Follow the steps below to change the video format.
If the OSD menus can be displayed using a PC
monitor, change the video format by following the
steps in
“4-1-1. Setting the video format” (<Operations and
Settings> Operating Instructions).
1
Connect the SDI monitor to the unit’s
SDI OUT 2 connector.
2
3
4
Turn on the power of the SDI monitor.
Turn on the power of the unit.
Hold down the OSD ON button.
1
2
Turn off the power of the unit.
The OSD ON button indicator lights, and the OSD
menus are displayed on the SDI monitor.
If the OSD menus do not appear on the monitor,
refer to “2-5-2. How to forcibly display the OSD
menus”.
Turn on the unit’s power while at the
same time holding down the button
that corresponds to the video format
supported by the SDI monitor.
Notes
Button to press at the same time
[OSD ON] + A bus crosspoint [1]
[OSD ON] + A bus crosspoint [2]
[OSD ON] + A bus crosspoint [3]
[OSD ON] + A bus crosspoint [4]
[OSD ON] + A bus crosspoint [5]
[OSD ON] + B bus crosspoint [1]
[OSD ON] + B bus crosspoint [2]
[OSD ON] + B bus crosspoint [3]
Video format
The OSD menus cannot be output from the
SDI OUT 1 connector.
1080/59.94i
1080/50i
If the OSD menu fails to appear on the SDI
monitor even after the above steps have been
taken, it may mean that the video format which
has been set in the unit is not the correct one.
Take the steps in the next section to change the
unit’s video format.
720/59.94p
720/50p
1080/24PsF
1080/23.98PsF
480/59.94i
576/50i
Refer to “Changing the video format”.
3
Hold down the OSD ON button.
The OSD ON button indicator lights, and the OSD
menus are displayed on the SDI monitor.
Note
If the OSD menu fails to appear on the SDI monitor
even after the above steps have been taken, it may
mean that the SDI monitor does not support the
unit’s SDI output format.
Check the input specifications of the SDI monitor.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Preparations
Changing the connector for
2-5. OSD (on-screen display)
menu operations
outputting the OSD menus
=ꢁꢆ?ꢀ1RGTCVKQPꢀ/GPW
The unit’s settings are selected using the OSD menus
which are displayed on the external monitor.
Described here is how to operate the OSD menus.
ꢀꢁꢂ15&ꢀ176
ꢀꢄꢂ15&ꢀ5K\G
5&+ꢃ176ꢄꢅ&8+ꢃ176
(7..
ꢀꢆꢂ15&ꢀ$CEM
1P
ꢀꢇꢂ-G[ꢀ2TKQTKV[
ꢀꢈꢂ$WUꢀ/QFG
2KP2ꢀQXGTꢀ-';
2)/ꢉ#ꢊꢋ256ꢉ$ꢊ
5GE
$-)&
'PCDNG
'PCDNG
1HH
7PNQEMGF
2-5-1. Displaying and clearing the
OSD menus
ꢀꢌꢂ6KOGꢀ7PKV
ꢀꢍꢂ5NKFGꢀ.GXGT
ꢀꢎꢂ)2+ꢀ+PRWV
ꢀꢏꢂ)2+ꢀ1WVRWV
ꢁꢐꢂ%CO%QPVꢀ.KPM
ꢁꢁꢂ5;56'/ꢀ/GPW
Basic operations
When the OSD ON button is held down, the OSD ON
button indicator lights, and the OSD menus are
displayed on the external monitor.
When the OSD ON button is held down while an OSD
menu is displayed, the OSD ON button indicator goes
off, and the OSD menu display is cleared.
The OSD menu output connector can be changed
using the “1. OSD OUT” item on the [13] Operation
Menu.
Note
SDI-OUT2:
The menus are output from the SDI OUT 2
connector.
DVI-OUT:
If parts of the OSD menus overlap the multi
view display frame, the split screen frames and
characters will not be displayed.
The menus are output from the DVI OUT
connector.
SDI-OUT2+DVI-OUT:
The menus are output from both the SDI OUT 2
connector and DVI OUT connector.
Note
The OSD menus cannot be output from the
SDI OUT 1 connector.
2-5-2. How to forcibly display the OSD
menus
When the OSD ON button is held down while holding
down the SHIFT button, the following settings are
established automatically.
The OSD ON button indicator lights, and the OSD
menus are displayed on the external monitor.
The output destination of the OSD menus is set
to both the SDI OUT 2 connector and DVI OUT
connector.
The screen size of the OSD menus output from the
DVI OUT connector is set to Auto.
(The menus are output in the size that corresponds
to the input specifications of the PC monitor which
is connected to the unit.)
24
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Preparations
2-5-3. Menu configuration and moving between menus
Menu configuration of the unit
The unit’s OSD menus are organized in two
Moving between the main menu and
submenus
Moving from the main menu to a submenu
To select a submenu item:
hierarchical levels: the main menu and the submenus.
Main menu:
This lists the submenu items.
Submenu:
Turn the OSD/TIME dial to select an item.
Entering the setting selected for the submenu item:
Press the OSD/TIME dial to enter the selected
item’s setting.
This displays the setting items and the settings.
The settings can be changed on this screen.
Moving from a submenu to the main menu
The main menu is restored to the screen when the
OSD ON button is pressed.
#9ꢌ*5ꢆꢍꢀ/CKPꢀ/GPW
=ꢀꢁ?ꢀ6+/'ꢂ%$)&ꢀ/GPW
=ꢀꢃ?ꢀ9+2'ꢀ/GPW
=ꢀꢄ?ꢀ2KP2ꢀ/GPW
=ꢀꢅ?ꢀ-';ꢀ5GVWRꢀ/GPW
=ꢀꢆ?ꢀ-';ꢀ#FLWUVꢀ/GPW
=ꢀꢇ?ꢀ%JTQOC-G[ꢀ/GPW
Submenu items
Main menu
=ꢀꢈ?ꢀ/WNVK8KGYꢀ2CVVGTPꢀ/GPW
=ꢀꢉ?ꢀ/WNVK8KGYꢀ1WVꢂ(TCOGꢀ/GPW
=ꢀꢊ?ꢀ:26ꢀ59ꢀ#UUKIPꢀ/GPW
ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀŤ
Statuses of the USER buttons
7ꢁꢋ2ꢌ256ꢁꢀ7ꢃꢋ2ꢌ256ꢃꢀ7ꢄꢋ2ꢌ256ꢄꢀ7ꢅꢋ2ꢌ256ꢅ
Turn the OSD/TIME dial, and select the
submenu item.
Press the OSD/TIME dial to enter the
selected item’s setting.
Press the OSD ON button.
=ꢁ?ꢀ6+/'ꢂ%$)&ꢀ/GPW
ꢀꢁꢎ#761ꢀ6KOG
ꢀꢀꢀꢀꢀꢁU^ꢀꢀꢀꢀꢀꢍH
ꢀꢀꢀꢀꢀꢁU^ꢀꢀꢀꢀꢀꢍH
ꢀꢀꢀꢀꢀꢁU^ꢀꢀꢀꢀꢀꢍH
ꢀꢀꢀꢀꢀꢁU^ꢀꢀꢀꢀꢀꢍH
$NCEM
ꢀꢃꢎ2KP2ꢀ6KOG
ꢀꢄꢎ-';ꢀ6KOG
ꢀꢅꢎ(6$ꢀ6KOG
ꢀꢆꢎ(6$ꢀ5QWTEG
Submenu
ꢀꢇꢎ#7:ꢀ$75ꢀ6TCPU ꢀꢀꢀꢀꢀꢁU^ꢀꢀꢀꢀꢀꢍH^&KUCDNG
ꢀꢈꢎ2KP2ꢀ$75ꢀ6TCPU ꢀꢀꢀꢀꢀꢁU^ꢀꢀꢀꢀꢀꢍH^&KUCDNG
Settings
ꢀꢉꢎ2KP2ꢀ'((&5.8
ꢀꢊꢎ5GVꢀ%$)&ꢀ%QN
ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀŤ
ꢀꢀꢀꢀꢀꢁU^ꢀꢀꢀꢀꢀꢍH^&KUCDNG
9JKVG
Setting items
Statuses of the USER buttons
7ꢁꢋ2ꢌ256ꢁꢀ7ꢃꢋ2ꢌ256ꢃꢀ7ꢄꢋ2ꢌ256ꢄꢀ7ꢅꢋ2ꢌ256ꢅ
USER button status display
The functions assigned to USER buttons 1 to 4 are
displayed on the last line of each menus screen.
Refer to “1-8. Setting the USER buttons”
Displaying menus consisting of
more than one page
When a menu contains many setting items, they are
displayed on more than one page.
When “” or “” is displayed, turn the OSD/TIME dial
on the line before the arrow to scroll the screen and
display the items which are hidden.
In this manual, only one menu screen is shown
even when that screen consists of more than one
page.
(<Operations and Settings> Operating Instructions).
In this manual, the menu screens are always shown
without the area where the USER button statuses
are displayed except under special circumstances.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Preparations
2-5-4. Operations using the submenus
1
Select the line with the setting item.
When the OSD/TIME dial is turned, the cursor “>” at the far left moves up or down.
Bring the cursor to the line with the setting item whose setting is to be changed, and then press the
OSD/TIME dial.
The cursor “>” now moves to the center where the setting can be changed.
The value to be set now blinks.
=ꢃ?ꢀ9+2'ꢀ/GPW
=ꢃ?ꢀ9+2'ꢀ/GPW
ꢀꢁꢂ2CVVGTP
ꢁ
ꢀꢁꢂ2CVVGTP
ꢁ
ꢀꢃꢂ&KTGEVKQP
0ꢄ4
ꢀꢃꢂ&KTGEVKQP
0ꢄ4
ꢀꢅꢂ$QTFGTꢄ5QHV
$ꢀꢀꢀꢆꢂꢆ^5ꢀꢀꢀꢆꢂꢆ
ꢀꢅꢂ$QTFGTꢄ5QHV
$ꢀꢀꢀꢆꢂꢆ^5ꢀꢀꢀꢆꢂꢆ
ꢀꢇꢂ5GVꢀ$QTFGTꢀ%QN 9JKVG
ꢀꢇꢂ5GVꢀ$QTFGTꢀ%QN 9JKVG
ꢀꢈꢂ#FLꢀ$QTFGTꢀ%QNꢀ *ꢀꢀꢀꢆꢂꢆ^5ꢀꢀꢀꢆꢂꢆ^.ꢀꢁꢆꢆꢂꢆ
ꢀꢉꢂ2QUKVKQP
ꢀꢈꢂ#FLꢀ$QTFGTꢀ%QN *ꢀꢀꢀꢆꢂꢆ^5ꢀꢀꢀꢆꢂꢆ^.ꢀꢁꢆꢆꢂꢆ
:ꢀꢀꢀꢀꢀꢊ^;ꢀꢀꢀꢀꢀꢊ^
ꢀꢉꢂ2QUKVKQP
:ꢀꢀꢀꢀꢀꢊ^;ꢀꢀꢀꢀꢀꢊ^
ꢀꢋꢂ5GVꢀ6Qꢀ2TGUGV ꢀꢀꢀꢀꢀꢀꢁ
ꢀꢋꢂ5GVꢀ6Qꢀ2TGUGV ꢀꢀꢀꢀꢀꢀꢁ
Turn the OSD/TIME dial,
and select the item.
Press the OSD/TIME dial
to enter the item.
The value to be set
now blinks.
2
Change the setting.
While the setting is blinking, turn the OSD/TIME dial. The setting in the blinking part now changes.
If a value has up to two decimal places, the speed at which the setting is changed can be increased by
turning the OSD/TIME dial while the SHIFT button is held down.
Memo
When values are changed for the regular setting items, these changes are reflected straight away but, with
some of the setting items (such as Format), the changes will not be reflected unless the OSD/TIME dial is
pressed once the changes have been made.
An asterisk () appears in front of the currently selected settings to identify these items.
=ꢃ?ꢀ9+2'ꢀ/GPW
=ꢃ?ꢀ9+2'ꢀ/GPW
ꢀꢁꢂ2CVVGTP
ꢁ
ꢀꢁꢂ2CVVGTP
ꢁ
ꢀꢃꢂ&KTGEVKQP
0ꢄ4
ꢀꢃꢂ&KTGEVKQP
0ꢄ4
ꢀꢅꢂ$QTFGTꢄ5QHV
$ꢀꢀꢀꢆꢂꢆ^5ꢀꢀꢀꢆꢂꢆ
ꢀꢅꢂ$QTFGTꢄ5QHV
$ꢀꢀꢀꢆꢂꢆ^5ꢀꢀꢀꢆꢂꢆ
ꢀꢇꢂ5GVꢀ$QTFGTꢀ%QN 9JKVG
ꢀꢇꢂ5GVꢀ$QTFGTꢀ%QN 9JKVG
ꢀꢈꢂ#FLꢀ$QTFGTꢀ%QN *ꢀꢀꢀꢆꢂꢆ^5ꢀꢀꢀꢆꢂꢆ^.ꢀꢁꢆꢆꢂꢆ
ꢀꢈꢂ#FLꢀ$QTFGTꢀ%QN *ꢀꢀꢀꢆꢂꢃ^5ꢀꢀꢀꢆꢂꢆ^.ꢀꢁꢆꢆꢂꢆ
ꢀꢉꢂ2QUKVKQP
:ꢀꢀꢀꢀꢀꢊ^;ꢀꢀꢀꢀꢀꢊ^
ꢀꢉꢂ2QUKVKQP
:ꢀꢀꢀꢀꢀꢊ^;ꢀꢀꢀꢀꢀꢊ^
ꢀꢋꢂ5GVꢀ6Qꢀ2TGUGV ꢀꢀꢀꢀꢀꢀꢁ
ꢀꢋꢂ5GVꢀ6Qꢀ2TGUGV ꢀꢀꢀꢀꢀꢀꢁ
Turn the OSD/TIME dial to change
the setting that is now blinking.
This part blinks.
[Returning the setting to its default value]
When the OSD/TIME dial is held down now, the value is returned to its default value.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Preparations
3
Move the blinking part.
When a setting item has a multiple number of settings, press the OSD/TIME dial to move the blinking part to
the right.
=ꢃ?ꢀ9+2'ꢀ/GPW
=ꢃ?ꢀ9+2'ꢀ/GPW
ꢀꢁꢂ2CVVGTP
ꢁ
ꢀꢁꢂ2CVVGTP
ꢁ
ꢀꢃꢂ&KTGEVKQP
0ꢄ4
ꢀꢃꢂ&KTGEVKQP
0ꢄ4
ꢀꢅꢂ$QTFGTꢄ5QHV
$ꢀꢀꢀꢆꢂꢆ^5ꢀꢀꢀꢆꢂꢆ
ꢀꢅꢂ$QTFGTꢄ5QHV
$ꢀꢀꢀꢆꢂꢆ^5ꢀꢀꢀꢆꢂꢆ
ꢀꢇꢂ5GVꢀ$QTFGTꢀ%QN 9JKVG
ꢀꢇꢂ5GVꢀ$QTFGTꢀ%QN 9JKVG
ꢀꢈꢂ#FLꢀ$QTFGTꢀ%QN *ꢀꢀꢀꢆꢂꢃ^5ꢀꢀꢀꢆꢂꢆ^.ꢀꢁꢆꢆꢂꢆ
ꢀꢈꢂ#FLꢀ$QTFGTꢀ%QN *ꢀꢀꢀꢆꢂꢃ^5ꢀꢀꢀꢆꢂꢆ^.ꢀꢁꢆꢆꢂꢆ
ꢀꢉꢂ2QUKVKQP
:ꢀꢀꢀꢀꢀꢊ^;ꢀꢀꢀꢀꢀꢊ^
ꢀꢉꢂ2QUKVKQP
:ꢀꢀꢀꢀꢀꢊ^;ꢀꢀꢀꢀꢀꢊ^
ꢀꢋꢂ5GVꢀ6Qꢀ2TGUGV ꢀꢀꢀꢀꢀꢀꢁ
ꢀꢋꢂ5GVꢀ6Qꢀ2TGUGV ꢀꢀꢀꢀꢀꢀꢁ
The blinking part moves
to the right.
This part blinks.
Press the OSD/TIME dial.
4
Complete the changes.
When the OSD ON button is pressed while a setting is blinking, the cursor “>” moves to the far left, and the
status for selecting the line with a setting item is restored.
=ꢃ?ꢀ9+2'ꢀ/GPW
=ꢃ?ꢀ9+2'ꢀ/GPW
ꢀꢁꢂ2CVVGTP
ꢁ
ꢀꢁꢂ2CVVGTP
ꢁ
ꢀꢃꢂ&KTGEVKQP
0ꢄ4
ꢀꢃꢂ&KTGEVKQP
0ꢄ4
ꢀꢅꢂ$QTFGTꢄ5QHV
$ꢀꢀꢀꢆꢂꢆ^5ꢀꢀꢀꢆꢂꢆ
ꢀꢅꢂ$QTFGTꢄ5QHV
$ꢀꢀꢀꢆꢂꢆ^5ꢀꢀꢀꢆꢂꢆ
ꢀꢇꢂ5GVꢀ$QTFGTꢀ%QN 9JKVG
ꢀꢇꢂ5GVꢀ$QTFGTꢀ%QN 9JKVG
ꢀꢈꢂ#FLꢀ$QTFGTꢀ%QN *ꢀꢀꢀꢆꢂꢃ^5ꢀꢀꢀꢆꢂꢆ^.ꢀꢁꢆꢆꢂꢆ
ꢀꢈꢂ#FLꢀ$QTFGTꢀ%QNꢀ *ꢀꢀꢀꢆꢂꢃ^5ꢀꢀꢀꢆꢂꢆ^.ꢀꢁꢆꢆꢂꢆ
ꢀꢉꢂ2QUKVKQP
:ꢀꢀꢀꢀꢀꢊ^;ꢀꢀꢀꢀꢀꢊ^
ꢀꢉꢂ2QUKVKQP
:ꢀꢀꢀꢀꢀꢊ^;ꢀꢀꢀꢀꢀꢊ^
ꢀꢋꢂ5GVꢀ6Qꢀ2TGUGV ꢀꢀꢀꢀꢀꢀꢁ
ꢀꢋꢂ5GVꢀ6Qꢀ2TGUGV ꢀꢀꢀꢀꢀꢀꢁ
This part blinks.
Press the OSD ON button.
Furthermore, the “>” cursor will move to the far left, and the status for selecting the line to be set will be
restored also when the OSD/TIME dial has been pressed while the blinking part is at the far right.
2-5-5. Indications used in this Operating Instructions
The operations for the setting items are indicated in this Operating Instructions as shown below.
Example: When operating the “5. Adj Border Col” item on the [2] WIPE Menu.
Submenu
Setting item
[2] WIPE Menu
5. Adj Border Col
27
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Preparations
2-5-6. Direct operations using the USER buttons and OSD/TIME dial
The functions that have been assigned to the USER buttons are displayed in the USER button status display area,
and the setting itemes which can be operated directly using the USER buttons and OSD/TIME dial are displayed
in the states listed below.
When this happens, the functions assigned to the USER buttons are disabled.
When the chroma key marker is displayed
When the submenu [2] WIPE Menu is displayed
When the submenu [3] PinP Menu is displayed
When the submenu [5] KEY Adjust Menu is displayed
When a particular USER button is pressed at this time, the status in which to change the settings shown in the
status area is established, and the value concerned can be changed by turning the OSD/TIME dial.
The values that have been changed are reflected instantly.
U1: USER 1 button
U2: USER 2 button
U3: USER 3 button (SHIFT button + USER 1 button)
U4: USER 4 button (SHIFT button + USER 2 button)
Example:When [2] WIPE Menu is displayed
The value of “B” for the 3. Border/Soft item has been set.
The “B” value is blinking.
=ꢃ?ꢀ9+2'ꢀ/GPW
Turn the OSD/TIME dial to change
the value.
ꢀꢁꢂ2CVVGTP
ꢁ
ꢀꢃꢂ&KTGEVKQP
ꢀꢅꢂ$QTFGTꢄ5QHV
0ꢄ4
=ꢃ?ꢀ9+2'ꢀ/GPW
$ꢀꢀꢀꢆꢂꢆ^5ꢀꢀꢀꢆꢂꢆ
ꢀꢇꢂ5GVꢀ$QTFGTꢀ%QN 9JKVG
ꢀꢈꢂ#FLꢀ$QTFGTꢀ%QN *ꢀꢀꢀꢆꢂꢆ^5ꢀꢀꢀꢆꢂꢆ^.ꢀꢁꢆꢆꢂꢆ
ꢀꢁꢂ2CVVGTP
ꢁ
ꢀꢉꢂ2QUKVKQP
ꢀꢊꢂ5GVꢀ6Qꢀ2TGUGV ꢀꢀꢀꢀꢀꢀꢁ
:ꢀꢀꢆꢂꢆꢆ^;ꢀꢀꢆꢂꢆꢆ^
ꢀꢃꢂ&KTGEVKQP
ꢀꢅꢂ$QTFGTꢄ5QHV
0ꢄ4
$ꢀꢀꢀꢆꢂꢆ^5ꢀꢀꢀꢆꢂꢆ
ꢀꢇꢂ5GVꢀ$QTFGTꢀ%QN 9JKVG
ꢀꢈꢂ#FLꢀ$QTFGTꢀ%QN *ꢀꢀꢀꢆꢂꢆ^5ꢀꢀꢀꢆꢂꢆ^.ꢀꢁꢆꢆꢂꢆ
7ꢁꢋ2QUꢌ:ꢀꢀ7ꢃꢋ2QUꢌ;ꢀꢀ7ꢅꢋꢌꢀꢀꢀꢀꢀꢀ7ꢇꢋꢌ
Press the USER 1 button.
ꢀꢉꢂ2QUKVKQP
:ꢀꢃꢈꢂꢈꢆ^;ꢀꢀꢆꢂꢆꢆ^
ꢀꢊꢂ5GVꢀ6Qꢀ2TGUGV ꢀꢀꢀꢀꢀꢀꢁ
7ꢁꢋ2QUꢌ:ꢀꢀ7ꢃꢋ2QUꢌ;ꢀꢀ7ꢅꢋꢌꢀꢀꢀꢀꢀꢀ7ꢇꢋꢌ
The indicator of the USER 1 button lights.
The “X” value is changed, and it is
reflected instantly.
The value stops blinking.
=ꢃ?ꢀ9+2'ꢀ/GPW
The cursor moves
to the last line that
displays the USER
button status.
ꢀꢁꢂ2CVVGTP
ꢁ
Press the USER 1 button.
ꢀꢃꢂ&KTGEVKQP
ꢀꢅꢂ$QTFGTꢄ5QHV
0ꢄ4
=ꢃ?ꢀ9+2'ꢀ/GPW
$ꢀꢀꢀꢆꢂꢆ^5ꢀꢀꢀꢆꢂꢆ
ꢀꢇꢂ5GVꢀ$QTFGTꢀ%QN 9JKVG
ꢀꢈꢂ#FLꢀ$QTFGTꢀ%QN *ꢀꢀꢀꢆꢂꢆ^5ꢀꢀꢀꢆꢂꢆ^.ꢀꢁꢆꢆꢂꢆ
ꢀꢁꢂ2CVVGTP
ꢁ
ꢀꢉꢂ2QUKVKQP
ꢀꢊꢂ5GVꢀ6Qꢀ2TGUGV ꢀꢀꢀꢀꢀꢀꢁ
:ꢀꢀꢆꢂꢆꢆ^;ꢀꢀꢆꢂꢆꢆ^
ꢀꢃꢂ&KTGEVKQP
ꢀꢅꢂ$QTFGTꢄ5QHV
0ꢄ4
$ꢀꢀꢀꢆꢂꢆ^5ꢀꢀꢀꢆꢂꢆ
ꢀꢇꢂ5GVꢀ$QTFGTꢀ%QN 9JKVG
ꢀꢈꢂ#FLꢀ$QTFGTꢀ%QN *ꢀꢀꢀꢆꢂꢆ^5ꢀꢀꢀꢆꢂꢆ^.ꢀꢁꢆꢆꢂꢆ
7ꢁꢋ2QUꢌ:ꢀꢀ7ꢃꢋ2QUꢌ;ꢀꢀ7ꢅꢋꢌꢀꢀꢀꢀꢀꢀ7ꢇꢋꢌ
ꢀꢉꢂ2QUKVKQP
:ꢀꢃꢈꢂꢈꢆ^;ꢀꢀꢆꢂꢆꢆ^
ꢀꢊꢂ5GVꢀ6Qꢀ2TGUGV ꢀꢀꢀꢀꢀꢀꢁ
The state in which the value (Pos-X)
of “X” for the 6. Position item can be
changed is now established.
7ꢁꢋ2QUꢌ:ꢀꢀ7ꢃꢋ2QUꢌ;ꢀꢀ7ꢅꢋꢌꢀꢀꢀꢀꢀꢀ7ꢇꢋꢌ
The USER 1 button indicator goes off, the direct
operation is canceled, and operation returns to the
3. Border/Soft item setting.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Preparations
2-5-7. Menu delegation function
When the buttons listed below are double-clicked, the specified menu is selected.
(The menu delegation function)
The operation corresponding to the button pressed is also executed.
<List of menu delegation functions>
Button
Menu selected
AUTO
FTB ON
KEY ON
PinP ON
WIPE
[1] TIME/CBGD Menu
[2] WIPE Menu
[3] PinP Menu
PinP
KEY-F/S
When any key type except “Chroma” has been selected:
[4] KEY Setup Menu
When “Chroma” has been selected as the key type:
[6] ChromaKey Menu
USER 1
USER 2
USER 3
(SHIFT + USER 1)
[12] USER/FMEM Menu
USER 4
(SHIFT + USER 2)
2-5-8. Bus status displays
When the A bus or B bus crosspoint buttons are held down, the BUS Assign Status menu appears for the OSD
menu.
POWER
ALARM
LINK
USER 1
3
USER 2
4
SHIFT
OSD/TIME
OSD ON
$75ꢀ#UUKIPꢀ5VCVWU
ꢁ
ꢀꢀ:26ꢀ59
ꢀꢀ:26ꢀ59ꢀ#UKIP
ꢀꢂꢀꢂꢀꢂꢀꢂꢀꢂꢀꢂꢀꢂꢀꢂꢀꢂꢀꢂꢀꢂꢀꢂꢀꢂꢀꢂꢀꢂꢀꢂꢀꢂꢀꢂꢀꢂꢀꢂꢀꢂ
AUX
PinP
KEY-F/S
MIX
WIPE
PinP ON
KEY ON
FTB ON
BUS DELEGATION
TRANSITION TYPE
5&+ꢂ+0ꢁꢀꢃꢀ+0276ꢁꢀꢀꢀꢄ
KEY-S
AUX
A
ꢀꢀ2)/
ꢀꢀ289
ꢀꢀ#7:
5&+ꢂ+0ꢁꢀꢃꢀ+0276ꢁꢀꢀꢀꢄ
5&+ꢂ+0ꢅꢀꢃꢀ+0276ꢅꢀꢀꢀꢄ
/8
SHIFT
PGM
PVW
KEY OUT
CLN
MV
5 10
CUT
1
6
2
7
3
8
4
9
ꢀꢀ2KP2
ꢀꢀ-';ꢀ(KNN
ꢀꢀ-';ꢀ5QWTEG
5&+ꢂ+0ꢁꢀꢃꢀ+0276ꢁꢀꢀꢀꢄ
%$)&
(/'/ꢁ
KEY-F
PinP
AUX
B
SHIFT
AUTO
BKGD
29
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Appearance
Unit: mm (inch)
189 (7-7/16)
S V N M
B O O T
D V I I N
4
D V I O U T
T A L L Y / G P I
L A N
2
I N
1 2 V
1
3
2
1
S D I I N
S D I O U T
O N
1
4
2
3
P O W E R
S I G N A L G N D
67 (2-5/8)
Compact Live Switcher AW-HS50
POWER
AUX
ALARM
LINK
USER 1
3
USER 2
4
SHIFT
OSD/TIME
KEY ON
OSD ON
FTB ON
PinP
KEY-F/S
MIX
TRANSITION TYPE
WIPE
PinP ON
BUS DELEGATION
KEY-S
AUX
A
SHIFT
PGM
PVW
KEY OUT
CLN
MV
CUT
1
6
2
7
3
8
4
9
5 10
KEY-F
PinP
B
AUX
SHIFT
AUTO
BKGD
53 (2-1/16)
210 (8-1/4)
30
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Specifications
Inputs
5 video lines
SDI 4 signal lines: SDI IN 1 to SDI IN 4
DVI-D 1 signal line: DVI IN
Outputs
3 video lines, 4 outputs
SDI 2 signal lines: SDI OUT 1, SDI OUT 2
(Only the SDI OUT 1 signals are split into two)
DVI-D 1 signal line: DVI OUT
Signal formats
SD
HD
480/59.94i, 576/50i
1080/59.94i, 1080/50i, 720/59.94p, 720/50p, 1080/24PsF, 1080/23.98PsF
Signal processing
Y:Cb:Cr 4:2:2, 10 bit (8 bits for frame memory)
RGB 4:4:4, 8 bit
ME number
SDI inputs
1ME
HD: Serial digital component (SMPTE 292M)
SD: Serial digital component (SMPTE 259M)
4 signal lines: SDI IN 1 to SDI IN 4
HD: SMPTE 292M (BTA S-004B) standard complied with
• 0.8 V [p-p] 10 % (75 )
• Input return loss
More than 15 dB (5 MHz to 1.5 GHz)
• Automatic equalizer 100 m (328 ft.) (when 5C-FB cable is used)
SD: SMPTE 259M standard complied with
• 0.8 V [p-p] 10 % (75 )
• Input return loss
More than 15 dB (5 MHz to 270 MHz)
• Automatic equalizer 200 m (656 ft.) (when 5C-2V cable is used)
DVI-D input
Digital RGB (Vertical frequency: 60 Hz):
XGA (1024 768), WXGA (1280 768), SXGA (1280 1024),
WSXGA+ (1680 1050), UXGA (1600 1200), WUXGA (1920 1200)
Digital RGB: 1080/50p, 1080/59.94p
Analog input signals are not supported.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Specifications
SDI outputs
HD: Serial digital component (SMPTE 292M)
SD: Serial digital component (SMPTE 259M)
2 signal lines: SDI OUT 1, SDI OUT 2
(Only the SDI OUT 1 signals are split into two)
HD: SMPTE 292M (BTA S-004B) standard complied with
• Output return loss
• Output level
• Rise time
More than 15 dB (5 MHz to 1.5 GHz)
0.8 V [p-p] 10 % (75 )
Less than 270 ps
• Fall time
Less than 270 ps
• Difference between rise time and fall time
Less than 100 ps
• Alignment jitter
• Timing jitter
• Eye aperture ratio
• DC offset
Less than 0.2 UI (130 ps)
Less than 1.0 UI
More than 90 %
0 0.5 V
SD: SMPTE 259M standard complied with
• Output return loss
• Output level
• Rise time
More than 15 dB (5 MHz to 270 MHz)
0.8 V [p-p] 10 % (75 )
Less than 1.5 ns
• Fall time
Less than 1.5 ns
• Difference between rise time and fall time
Less than 0.5 ns
• Jitter
Less than 0.2 UI
DVI-D output
Digital RGB (Vertical frequency: 60 Hz):
XGA (1024 768), WXGA (1280 768), SXGA (1280 1024),
WSXGA+ (1680 1050), UXGA (1600 1200), WUXGA (1920 1200)
Digital RGB: 1080/50p, 1080/59.94p
High-resolution multi view mode supported:
Signals are also output with a high resolution even when SD has been selected
as the system mode.
When the high-resolution multi view mode is enabled, MV is assigned to
the DVI OUT connector, and MV cannot be assigned to the SDI OUT 1
connectors or SDI OUT 2 connector.
Analog output signals are not supported.
Video delay time
1 frame (F)
Video signals that have passed through the PinP, multi view display, DVI-D input
or DVI-D output will be delayed in each case by up to one frame.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Specifications
Control I/O
LAN (RJ-45)
Connecting cable:
10BASE-T/100BASE-TX
(For IP control)
LAN cable (category 5 or above),
max. 100 m [328 ft.], STP (Shielded Twisted Pair)
cable recommended
When connecting to a hub (switching hub), use a
straight cable.
Use a crossover cable when connecting the unit
and another device on a 1:1 basis without going
through a hub.
TALLY/GPI
(D-sub 15-pin, female,
inch thread)
INPUT : 5 inputs, photocoupler sensing
OUTPUT : 7 outputs, open collector output
(negative logic)
Other
SERVICE switch [SV/NM] (for maintenance purposes)
Normally, this switch is used as the “NM” position.
Ambient operating
temperature
0 °C to 40 °C (32 °F to 104 °F)
Humidity
10 % to 90 % (no condensation)
DC 12 V 10 % (AC adapter provided)
2.0 A (DC 12 V)
Power requirements
Current consumption
Dimensions
210 67 177 mm (8-1/4˝ 2-5/8˝ 6-15/16˝)
(W H D)
[excluding protrusions]
Mass
1.4 kg (3.08 lbs.)
Supplied AC adapter
Rated input: AC 100 V to 240 V, 1.3 A, 47 Hz to 63 Hz
Rated output: DC 12 V, 3.5 A, 42 W
The provided power cable is for 125 V AC or less.
Use it within AC 100 V to 120 V.
The AC adapter and power cable provided must be used without fail.
Mass and dimensions shown are approximate.
Specifications are subject to change without notice.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
© Panasonic System Networks Co., Ltd. 2010
D
F0610Y1070
Download from Www.Somanuals.com. All Manuals Search And Download.
|