LCD TV COMBO
TFTV1920D
USER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended
to alert the user to the presence of uninsulated “Dangerous Voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
CAUTION: Laser radiation when open. Do note stare into
beam.
CAUTION: USE OF ANY CONTROLS, ADJUSTMENTS, OR PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
CAUTION
1.
2.
3.
The product contains a low-power laser device. In order to ensure the safety of the laser device,
do not remove any cover and attempt to repair the unit. If any service is needed, please contact
the distributor or its authorised service centre.
To reduce the risk of electric shock, do not remove the cover (or back). No user-serviceable
parts inside. Refer servicing to qualified service personnel. Unplug the product from the wall
outlet before servicing or when it is unused for a long period of time.
The manufacturer should not hold responsibility for the damage caused by any substitutions
and modifications of the product without authorisation from the manufacturer or authorised unit.
WARNING
The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids,
such as vases, shall be placed on the apparatus.
Copyright Protection
The product incorporates copyright protection technology that is protected by U.S. patents and
other intellectual property rights. Use of this copyright protection technology must be authorised
by Macrovision, and is intended for home and other limited viewing uses only unless otherwise
authorised by Macrovision, Reverse engineering or disassembly is prohibited.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
Note:
1. Read these instructions.
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus
near water.
2. DANGER: Visible laser radiation when open and interlock
failed or defeated. Avoid direct exposure to beam.
3. CAUTION: Do not open the top cover. There are no user
serviceable parts inside the unit. Leave all servicing to
qualified service personnel.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Maintain well ventilated conditions around the product.
Do not put product on bed, sofa or anything that blocks ventilation. Install in according to the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9. Read, heed and follow all instructions to ensure correct and safe installation and
inter-connection of the apparatus.
10. The apparatus shall not be exposed to dripping or splashing and no objects filled with
liquids, such as vases, shall be placed on the apparatus.
11. The mains socket outlet shall be installed near the apparatus and the mains plug shall remain
readily operable.
12. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
13. Only use attachments/accessories specified by the manufacturer.
14. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
15. Unplug this apparatus during lightning storms or when unused for long periods of time.
16. Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain
or moisture, does not operate normally, or has been dropped.
17. The apparatus shall be connected to a mains socket outlet with a protective earthing
connection.
Note: Do not touch the colour TFT LCD screen by hand directly.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Characteristic Features
This product incorporates DVD player, LCD display and TV receiver in one system.
Multiple Mode
Auto TV Searching Function
Can be connected to the TV antenna, supports
TV mode
Auto and manual TV programs searching
function.
CVBS mode
S-VIDEO mode
COMPOSITE mode
VGA mode
NICAM Function
Supports the NICAM function. According to the
broadcasting programs, you can choose the
corresponding soundtrack
DVD mode
High Quality Property
High Resolution
Advanced Playing Features
Adopt an MPEG2 decoding format to achieve
horizontal resolution more than 500 lines.
Compatibility
DVD, CD, and JPEG discs compatible.
LCD (Liquid Crystal Display)
Designed with 19" colour TFT liquid crystal
display clearly shows the data.
All Playback Functions
Fast forward and reverse, slow playback and
repeat playback
Stereo Amplifier
Built-in two speakers provide high quality
sound.
Special Playback
Support multi-angle, multi-language and
multi-subtitle playback.
AV and VGA Input
Can be connected to external audio and video
signal source and PC.
NOTE: It is normal for a TFT screen to
experience some light or dark spots appearing
on the LCD screen.
Special Function
Support sleep time setting function and favourite
channel setting function, etc.
Multi Audio and Multi-video modes
Support multi-audio and multi-video modes,
provides more selecting.
USB and CARD PORTS
Designed with USB an SD/MS/MMC card pot,
can be connected to USB device or
SD/MS/MMC.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Disc Information
Discs Formats Supported By This Player
DISC LOGO
CONTENTS
SIZE
MAXIMUM TIME
133min(SS-SL)
242min(SS-DL)
266min(DS-SL)
484min(DS-DL)
Audio+Video
(active picture)
DVD
12cm
CD
Audio
12cm
12cm
74min
JPEG
Still high resolution
The operating method of some DVD discs is specified by the software maker. Please refer to
the instruction manual of the disc.
About Disc Terms
Title
Generally, pictures or music compressed on a DVD are divided into several sections, “title”.
Chapter
The smaller section unit of picture or music in a DVD under the title, usually one title is comprised of
one or more chapters and each of them is numbered for easy searching. But some discs may not
have a recording chapter.
Track
A segment of picture or music on a CD. Each track is numbered for searching.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Panel
1
16
16
14
15
1. 19" colour TFT screen
19" colour TFT screen clearly show the data.
2. SOURCE button
Press to select mode among TV, CVBS, S-VIDEO, COMPONENT, VGA and DVD.
In setup menu, the same function as ENTER button.
3. MENU button
Press to enter or return to the previous setup menu.
4. CH
In the TV mode, press to select channels.
In setup menu, the same function as
5. VOL button
In the TV mode, press to decrease or increase the volume.
/
button
/
direction buttons.
/
In setup menu, the same function as
PLAY button
/
direction buttons.
6.
7.
Press to play the disc in DVD mode.
STOP button
Press to stop disc playback in DVD mode.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Front and Right Side Panel
1
16
16
14
15
8. Eject button
Press to eject the disc out in DVD mode.
9. Power button
Press to enter or exit the standby mode.
10. SD/MS/MMC Card Port
Insert the SD, MS or MMC card into the port.
11. Disc Tray Slot
Used to load disc.
12. Earphone Jack
When connected to earphone, the internal speakers will automatically turn off.
13. USB Connecting Port
Connecting to the USB device.
14. Remote Sensor
Remote sensor window for the remote control.
15. Power Indicator
In normal playback status, it is blue; in standby mode, it turns red.
16. Speakers
Two speakers output high quality stereo sound.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Left Side Panel
1. Y/Pb/Pr Input Jack
5. TV Signal Input Jack
Connected for the external TV signal
input.
Connected to the Y/Pb/Pr input in
COMPONENT mode.
2. Y/Pb/Pr L/R Audio Input Jack
Connected to the L/R audio input in
COMPONENT mode.
6. DC 12V Input Jack
Connect the power adaptor or the car
adaptor.
3. Composite Audio/Video Output Jack
In the CVBS mode, connected to output
the Audio/Video signals.
7. VGA Input Jack
Connected to the VGA output jack on a
personal computer.
4. S-VIDEO and CVBS Audio/Video Input
Jack
8. PC AUDIO Input Jack
Connected to the PC audio output jack.
Connected to the S-VIDEO input in
S-VIDEO mode or CVBS input in the
CVBS mode. The L/R audio input jacks
can be used in the both S-VIDEO and
CVBS modes.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control
5. S.M. button
Remote Control Drawing
Press to shift the sound modes among
User, Standard, Music, Movie and
Speech.
1
6. 0-9 Number buttons
Press to select numbers such as TV
channel.
22
2
3
4
5
23
24
25
7. FAV button
Press to access to the favourite channel
8. STEREO/AUDIO button
Press to shift sound track when in TV
mode.
6
Press to select audio language or audio
track when in DVD mode.
9. VOL+/- button
Press to increase or decrease the volume.
10. MUTE button
26
7
8
27
28
29
9
10
Press to turn on or off speaker output
11. EXIT button
30
11
12
Press to exit from the setup menu.
12. Direction buttons (
)
13
14
In the setup menu, press the
to select the desired items, press the
button to adjust or set.
button
31
32
33
15
16
17
13. ENTER button
Press to confirm selection.
34
14. SOURCE button
35
36
18
19
Press to select modes among TV, CVBS,
S-VIDEO, COMPONENT VGA and DVD.
37
38
20
21
15.
16.
PLAY button
Press to play a disc when in the DVD
mode.
PAUSE button
When in the DVD mode, press to pause
playback. Press the PLAY button to
resume normal playback.
1. POWER button
Press to turn on or off this unit.
2. TV button
Press to shift to TV mode.
3. DVD button
Press to shift to DVD mode.
4. P.M. button
17.
/
button
Press to search backward or forward
when in DVD mode.
Under teletext mode, it's the teletext colour
button.
Press to shift the screen picture modes
among User, Standard, Soft, Bright and
Shine.
18. TITLE button
When a DVD disc is playing, press the TITLE
button to go to the title menu and display
disc contains.
Under TV, CVBS or S-VIDEO mode,
press to display/close the teletext.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control
19. MENU button (under DVD mode)
Press to enter disc menu when in DVD
mode.
31. SLEEP button
This feature allows you to set up sleep
time when in TV mode. Press the button
repeatedly to select the desired sleep time
or "Off" to close this function
32. Eject button
Under teletext mode, press to disable
teletext display and press again to
resume.
20. SETUP button
Press to eject the disc from the unit.
33. STOP button
Press to open DVD setup menu when in
DVD mode.
Under teletext mode, press to display the
index page.
Press to stop disc playback, when in DVD
mode.
34.
/
button
21. SLOW button
Press to skip to the previous or next
chapter/track when in DVD mode.
Under teletext mode, it's the teletext colour
button.
Press to activate slow playback under
when in DVD mode.
Under Teletext mode, press once to
display the concealed information, such
as solution of riddles or puzzles; press
again to resume the riddles information
from the display.
35. REPEAT button
Press to repeat a chapter, track, title, or all
content when in DVD mode.
Under teletext mode, press to freeze the
current page and press again to resume.
36. ANGLE button
22. VGA button
Press to shift to VGA mode.
23. COMPONENT button
Press to enter COMPONENT mode.
24. DISPLAY button
Press to access various camera angles (if
the DVD disc contains multiple camera angles)
when in DVD mode.
Press to display the reference information
about the current program.
25. SET FAV button
Under Teletext mode, Press the button first
time to double the size of teletext letters in
the upper half of the screen, second to
double the size of teletext letters in the
lower half of the screen and third to
resume normal status.
Press to set current channel as the
favourite channel.
26.
/+10 button
In the TV mode, press to return to the
channel last viewed. When in DVD
mode, press to select numbers greater
than 10.
37. CARD button
Press to shift among disc playback, USB
playback and SD/MS/MMC playback.
Under teletext mode, press to select four
groups 3-digit numbers that displayed in
different colours at the bottom of the screen.
Press the colour buttons on the remote
control to select, then use the number
buttons to input the corresponding number
to display the page.
27. SCAN/SUBTITLE button
When in TV mode., press to scan the
programs and press again to stop
scanning. When in DVD mode, press to
select alternate subtitle languages during
playback of a multiple language DVD disc.
28. CH+/- button
Repeat the above procedures for each
page to be stored, using a different colour
button accordingly each time.
When in TV mode, press to select
channel.
29. ASPECT button
38. GOTO button
Press to shift the aspect ratio of the
30. screen between Fill Screen and Aspect
Normal.
Press to select the desired disc starting
time, title or chapter when in DVD mode.
Under TV mode, press to display the
real clock and press the EXIT button to
exit.
MENU button
Press to enter or exit the setup menu.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
System Connections
Before connections, disassemble the jack cover first.
Do not connect the power cord until all other connections have been made.
Ensure that you observe the colour cord when connecting audio and video cables.
Connecting to Power Supply
Power is supplied through the provided appropriate power adapter, one end is connected to the
DC 12V IN jack on the side panel of the unit, the other end to the wall AC outlet.
To wall AC Outlet
Connecting to External AV Signal Source
Use the audio and video cable to connect the AV input jacks on the side panel of the unit to the
external AV signal source. Use the S-VIDEO cable to connect the S-VIDEO input jack on the side
panel of the unit to the external AV signal source.
After connection, turn on the power of the unit and the external AV signal source and then press the
SOURCE button to shift to CVBS or S-VIDEO mode.
Note: the L/R audio input jacks can be used in the both CBVS and S-VIDEO modes.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
System Connections
Connecting External AV Signal Source (YPbPr)
Use the audio and video cables to connect the Y/Pb/Pr input Jacks on the side panel of the unit to
the external AV signal source.
After connection, turn on the power of the unit and external AV signal source and then press the
SOURCE button to shift to COMPONENT mode.
Connecting to External AV Input Device (AV Output)
Use the audio and video cable to connect the AV output jacks on the side panel of the unit to the
external AV input device.
After connection, turn on the power of the unit and external AV input device and then press the
SOURCE button to shift to the corresponding mode.
Note: The unit can only output TV, CVBS and S-VIDEO signals.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
System Connections
Connecting to PC
The unit can be connected to PC (person computer) via the VGA cable. Follow the steps and the
figure below to connect.
1. Connect one end of the VGA cable to the VGA input jack on the side panel and the other end
to the PC.
2. Connect one end of the audio cables to the PC audio input jack on the side panel and the other
end to the PC audio output jack.
3. Set the PC's resolution at 1024x768@60Hz.
After connection, turn on the unit and the PC and then press the SOURCE button to shift to VGA
mode.
Connecting to Earphones
This unit can be connected to an earphone for listening music privately. See the below figure for
details:
After connecting to the earphone, the internal speakers output will turn off automatically.
Note: Excessively loud volume could damage your hearing. So turn down the volume before
you connect the headphones, and then raise the volume to comfortable level.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
System Connections
Connecting to TV Antenna
This unit can be connected to the TV signal input source via the TV jack on the side panel.
After connection, turn on the power of the unit. Then press the SOURCE button to shift to TV mode.
After connecting to the antenna, turn on the unit, and go on with program searching, you can
follow the below steps to select channels:
1. For 0~9 channel:
Press the number buttons to select the channel X, wait several seconds and it will go to the
selected channel.
Or press the number buttons to select channel X, and press the ENTER button to go to the
selected channel immediately.
Or press the number buttons to select channel 0X, and it will go to the selected channel
immediately.
2. For 10~99 channel:
Press the number buttons to select channel XX, and it will go to the selected channel
immediately.
* X is the channel number.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Function
NOTE: In other mode, you can refer to the following instructions in TV mode to go on with
some settings. Only when there are signals, the menus can appear and be set.
Preparation
1. After connection, press the POWER button to turn on the power. (If it is turned on, the power
indicator is blue.)
2. Press the SOURCE button to shift to TV mode. You can go on with the following operations.
Image Setting
Note: This item is only available when there is signal input.
Image
Audio
Setup
Scheme
Picture
Press the MENU button once to enter the setup
menu. Press the button to select Image and
press the ENTER button to enter the menu
shown on the right.
Brightness
Contrast
Hue
In the Image setup menu, press the
select the desired item. Press the MENU button to
return to the previous menu.
button to
Color
Sharpness
Advanced
Image
Audio
Setup
Scheme
Scheme Setup
Press the
button to select Scheme and
Normal
Vivid
press the ENTER button to enter. Press the
button to select the desired item and press
the ENTER button to confirm your selection.
Press the MENU button to return to the previous
menu.
Sports
Nature
Picture Setup
Image
Audio
Setup
Picture
Press the
button to select Picture and
press the ENTER button to enter. Press the
button to select the desired item and press
the ENTER button to confirm your selection.
Press the MENU button to return to the previous
menu.
User
Standard
Soft
Bright
Shine
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: This item is only available in DVD, VGA COMPONENT modes.
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Function
When the VGA signal is connected to the unit, the Advanced setup menu is shown below:
Image
Audio
Setup
Advanced
Press the "
" button to select the desired
Auto Adjust
Image Pos
Phase
item and press the "ENTER" button to enter it's
setup menu. Press the "MENU" button to return
to the previous menu.
Clock
Auto Color
SRGB
Auto Adjust:
If the monitor is not clear, you should carry out "Auto Adjust".
Press the "
Press the "
" button to select "Auto Adjust" and press the "ENTER" button to enter it's menu.
" button to select "Yes" to activate this function or "No" to cancel. Press the "MENU"
button to return to the previous menu.
Image Pos:
Press the "
" button to select "Image Pos" and press the "ENTER" button to enter it's menu
Within the menu, press the "
" button to move the image. Press the "MENU" button to return
" button to select "Phase". Press the " " button to adjust the value. Press the
to the previous menu.
Phase:
Press the "
"MENU" button to return to the previous menu.
Clock:
Press the "
" button to select "Clock" and press the "ENTER" button to enter it's menu. Press
the "
"button to adjust the value . Press the "MENU" button to return to the previous menu.
Auto Color:
Press the "
" button to select "Auto Color" and press the "ENTER" button to activate this
function. Press the "MENU" button to return to the previous menu.
sRGB :
Press the "
" button to select "sRGB" and press the "ENTER" button to enter it's menu. Press
the "
" button to select "On" to activate this function or "Off" to cancel. Press the "MENU"
button to return to the previous menu.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Function
Audio Setting
Image
Audio
Setup
Volume
Bass
Press the MENU button once to enter the setup
menu. Press the
button to select Audio and
Treble
press the ENTER button to enter the menu shown on
the right.
Balance
Auto Volume
Sound Mode
In the Audio setup menu, press the
button to
select the desired item. Press the MENU button to
return to the previous menu.
Volume Setup
Press the
button to select Volume and press the
button to adjust the level. Press the
button to adjust the level. Press the MENU
button to adjust the level. Press the
button to select Balance and press the button to adjust the level. Press the
MENU button to return to the previous menu.
Bass Setup
Press the
button to return to the previous menu.
button to select Bass and press the
Treble Setup
Press the
MENU button to return to the previous menu.
button to select Treble and press the
Balance Setup
Press the
MENU button to return to the previous menu.
Auto Volume Setup
Press the
Press the
button to select Auto Volume and press the ENTER button to access the menu.
button to select "On" or "Off' and press the ENTER button to confirm. Press the
MENU button to return to the previous menu.
Sound Mode Setup
Image
Audio
Setup
Sound Mode
Press the
button to select Sound Mode and
press the ENTER button to enter. Press the
button to select the desired item and then press the
ENTER button to confirm your selection. Press the
MENU button to return to the previous menu.
User
Standard
Music
Movie
Speech
18
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Function
Setup Setting
Press the MENU button once to enter the setup
menu. Press the
button to select Setup and
Image
Audio
Setup
Tuner/Channel
Language
Factory Reset
press the ENTER button to enter the menu shown on
the right.
In the Setup menu, press the
button to select
the desired item. Press the MENU button to return to
the previous menu.
Tuner/Channel
Press the
button to select the
Image
Audio
Setup
PAL Tuner/Channel
Tuner/Channel and press the ENTER button
to enter the menu shown on the right. Press the
button to select the desired item. Press
the MENU button to return to the previous
menu.
Country
Auto Scan
Prog Organizer
Manual Install
Country
Image
Audio
Setup
PAL Tuner/Channel
Press the
button to select the
Country and press the ENTER
Country Select
button to enter the menu shown on
the right. Press the
button to
Australia
Belgium
UK
select the desired item. Press the
MENU button to return to the
previous menu.
France
Czech
Denmark
19
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Function
Auto Scan
Press the
button to select the Auto Scan and press the ENTER button to start auto scan. The
screen will display shown below:
Auto scan
CH No
8
FREQ 154.20 MHz
Auto scan will take a few minutes, when the tuning operation completes the unit will exit and
memorise the programs by sequence automatically.
During tuning, press the MENU button to exit the auto scan mode
Prog Organizer
Image
Audio
Setup
PAL Tuner/Channel
Press the
button to select the
Prog Organizer and press the
ENTER button to enter the menu
shown on the right.
Prog Organizer
XXXXXXX
Channel Name
Skip
In the Prog Organizer setup menu,
press the
button to select the
Swap From Ch
Swap To Ch
Perform Swap
desired item. Press the MENU
button to return to the previous
menu.
Channel Name
Press the
press the
button to select the Channel Name and press the ENTER button to enter. Then
button to select letters or press the number button to input numbers. Press the
MENU button to return to the previous menu.
Skip
Press the
button to select Skip and press the ENTER button to activate or cancel this function.
Press the MENU button to return to the previous menu.
Swap
Press the
button to select Swap from Ch and press the ENTER button to enter. Press the
number buttons to select program number. Repeat the above operations to Swap To Ch. Then
Press the
button to select Perform Swap and press the ENTER button to confirm.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Function
Image
Audio
Setup
PAL Tuner/Channel
Manual Install
Press the
button to select the
Manual Install
Manual Install and press the
ENTER button to enter the menu
shown on the right.
47.00 MHz
Search
Color System
Fine Tune
CH NO
In the Manual Install setup menu,
press the
button to select the
desired item. Press the MENU
button to return to the previous
menu.
Store
Search
Press the
button to select Search and press the or to start searching forward or
backward. Press the MENU button to return to the previous menu.
Colour System
Press the
button to select Colour System and press the ENTER button to enter. Press the
MENU button to return to the previous menu.
Fine Tune
Press the
button to select Fine Tune and press the ENTER button to enter. Press the or
controls to start fine tuning forward or backward. Press the MENU button to return to the previous
menu.
This feature allows for minor adjustments to the integrated electronic tuner's ability to tune in weak
broadcast signals or where applicable solve minor irregularities in cable channel tuning parameters.
CH NO
Press the
button to select CH NO and press the ENTER button to enter. Press the number
buttons to enter the channel number. Press the button to return to the previous menu.
Store
Press the
button to select Store and press the ENTER button to store the above operations.
Note: The "CH NO" and "Store" items only function when the program is searched out.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Function
Language
Image
Audio
Setup
Language
Press the
button to select the Language, press
the ENTER button to enter the setup, press the
button to select item. Press the MENU button to
return to the previous menu.
English
French
Spanish
German
Italian
Factory Reset
Press the
button to select the Factory Reset
Image
Audio
Setup
Factory Reset
and press the ENTER button to enter. Press the
button to select "Yes" or "No", and press the ENTER
button to reset to the default status or to cancel.
Press the MENU button to return to the previous
menu.
Yes
No
22
Download from Www.Somanuals.com. All Manuals Search And Download.
NICAM Function
The unit support NICAM function under TV mode.
Under NICAM TV broadcast:
1. When receiving stereo audio signals, press the STEREO/AUDIO button on the remote control
repeatedly to shift the sound tracks between Nicam Stereo and Mono and the screen will
appear corresponding display as shown below:
Mono
Nicam Stereo
2. When receiving bilingual audio signals, press the STEREO/AUDIO button on the remote
control repeatedly to shift the sound tracks among Nicam I, Nicam II, Nicam I+II and Mono
and the screen will appear corresponding display as shown below:
Mono
Nicam I+II
Nicam II
Nicam I
3. When receiving mono audio signals, press the STEREO/AUDIO button on the remote control
repeatedly to shift the sound tracks between Nicam Mono and Mono and the screen will
appear corresponding display as shown below:
Mono
Nicam Mono
Under A2 TV broadcast:
1. When receiving stereo audio signals, press the STEREO/AUDIO button on the remote control
repeatedly to shift the sound tracks between Stereo and Mono and the screen will appear
corresponding display as shown below:
Mono
Stereo
2. When receiving bilingual audio signals, press the STEREO/AUDIO button on the remote
control repeatedly to shift the sound tracks among I, II and I+II and the screen will appear
corresponding display as shown below:
II
I
I + II
3.
When receiving mono audio signals, press the STEREO/AUDIO button on the remote control to
display sound track Mono on the screen.
Mono
23
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD Playback Operation
Preparation:
After connections, turn on the unit and select the relevant video input before playback.
Disc Loading Steps:
1. Press the POWER button to turn on the power. Press the SOURCE button and select DVD,
press the ENTER button to confirm and shift to DVD mode.
2. Handing the disc with its printed side outward vertically to the disc tray. (Referring to the
below picture.)
3. Slightly put the disc into the disc tray.
4. As disc is automatically taken in the disc tray fully, the player will search a disc and play it
automatically in DVD mode.
Warning: Do not play poor quality discs that may damage the player's lens.
DVD Playback
Region Code
DVD players and discs are coded by region. These regional codes must match the played discs. If
the codes don't match, the disc cannot be played. This player's default code is region 4.
Play
Press the PLAY button to start playback. Press the STOP button once on the remote control to stop
playback, and press the PLAY button again to resume playback.
Stop
Press the STOP button once to stop playback and press the
PLAY button to resume normal
playback. Press this button twice repeatedly to stop playback completely.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD Playback Operation
Pause
Press the
PAUSE button once to pause the playback; press it repeatedly to start step-by-step
playback. Press the
PLAY button to resume normal playback.
Previous
and
Next
Press the
button to go to the next chapter. Press the
button once to return to the beginning of
the current chapter or track; press it twice to go to the previous chapter.
Fast Playback
Press the
or
FWD/REV SCAN button on the remote control to activate fast backward or
forward playback.
SLOW
During DVD disc playback, press the SLOW button on the remote control to start slow playback.
During slow playback, press the PLAY button to resume normal playback.
Repeat
Use the REPEAT button repeatedly to repeat a chapter, title or all.
Some discs do not support the repeat function.
Menu
Normally there is a selecting menu for DVD discs. You can press the MENU button (under DVD
mode) to enter the menu, and use the direction buttons to highlight an item. Then press the ENTER
button to confirm.
Title & Chapter
Normally there are several titles in a DVD disc, and several chapters (sections) in a title. You can
select any title or chapter quickly by entering the relevant number.
Language (Audio)
There can be up to 8 audio languages on a DVD disc. When you play a multi-language DVD disc
you can use press the AUDIO button on the remote control to select a language.
Subtitle
The DVD player can support multiple kinds of subtitles. When you play a multi-subtitle disc you can
press the SUBTITLE button on the remote control to select different subtitles.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD Playback Operation
GOTO
During DVD disc playback, press the GOTO button on the remote control once, there will be a
menu displayed on the screen. You can set or select items for your preference. Use the
direction buttons to select items and press the ENTER button to enter and use the
buttons to select the desired item. Press the direction button to return. When select the
Title/Chapter, TT Time/CH Time, use number buttons to input desired title/chapter number time.
direction
Some DVD discs do not support the search function.
Various Camera Angles
The movies on some DVDs have been recorded from various camera positions. This lets you enjoy
the same scene from different perspectives. In this case you'll usually find a marking on the DVD
sleeve.
When playing a DVD containing various camera angles the camera symbol appears on the screen.
Press the ANGLE button repeatedly until the desired perspective is shown. The picture will be
adjusted in 1~2 seconds.
CD Playback
The player will play all tracks on a CD disc by default. You can use the
buttons, or number buttons to select a track.
and
(PREV/NEXT skip)
Stop
Press the STOP button once to stop playback and press the PLAY button to resume normal
playback. Press this button twice repeatedly to stop playback completely.
Pause
Press the
PAUSE button to pause the playback and then press the
PLAY button to resume
normal playback.
Previous and Next
Press the
track.
button once to go the beginning of this track. Press twice repeatedly to go the previous
Press the
button to play from the beginning of the next track.
Fast Playback
Press the or
forward playback.
FWD/REV SCAN button on the remote control to activate fast backward or
26
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD Playback Operation
Repeat
Use the REPEAT button repeatedly to repeat Track, All or to cancel repeat.
Some discs do not support the repeat function.
Audio
During CD playback, press the AUDIO button on the remote control to select the audio output mode:
Mono Left, Mono Right, Mix-Mono and Stereo.
GOTO
Press the GOTO button to access the time-selected state. You can select Disc Go To, Track Go To
or Select Track respectively by pressing this button repeatedly. Use the 0-9 buttons to enter the
desired time, and then the player will play according to the selected time.
JPEG Playback
JPEG is a common picture format that requires small amounts of storage per image and has low
loss in resolution. Hundreds of pictures can be stored on a disc in this format. In order to view JPEG
photo albums, you can ask your film development company to make a "PICTURE CD" when they
develop your film.
Normal Playback
Load a JPEG disc in. For JPEG disc, there will be a root menu displayed on the screen. Use the OK
button and the direction button to select a submenu, and then use the
to select the contents. Many discs have other contents besides pictures.
For Picture CD disc, it will display the pictures automatically.
direction button
During playback, press the
Many discs have other contents besides pictures.
Stop
or
button to select picture.
Press the STOP button once to stop playback and return to the preview menu. Press the
PLAY button to resume normal playback. Press this button twice repeatedly to stop playback
completely.
Pause
Press the
PAUSE button to pause playback, press the PLAY button to resume playback.
Repeat
During playback, press the REPEAT button repeatedly, and the repeat modes are Shuffle, Random,
Single, Repeat One, Repeat All and Repeat Off.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD Playback Operation
Previous and Next
During playback, press the
or
button to select picture.
Menu
Press the MENU button once to stop playback and return to the root menu.
GOTO
During playback, press the GOTO button on the remote control once, use the number buttons to
input the file number.
Picture Rotation
This can be used only when the picture is normally displayed. Once another picture is selected,
rotation will be cancelled automatically. Use the
buttons to rotate the picture.
Some JPEG disc may not support rotating
28
Download from Www.Somanuals.com. All Manuals Search And Download.
USB and SD/MS/MMC Card Function
USB and SD/MS/MMC Card Function
Preparation:
1. Connect the unit to the power supply.
2. Press the POWER to turn on the unit.
3. Press the SOURCE button to shift to DVD mode.
4. Insert the USB into the unit’s USB slot, or insert the SD/MS/MMC card into the SD/MS/MMC
card slot on the right side of the unit. Please see the below figure:
Make sure that files are stored in the USB and the SD/MS/MMC card before the connection.
5. Press the CARD button to shift among disc playback, USB playback and the SD/MS/MMC
playback. The default state is disk playback. Please see the below figure:
00:00
00:00
001/002
BAK
JPEG
6. Press the
7. Press the
playback.
button to select the folder, and press ENTER button to enter.
buttons to select the desired track. Then press PLAY
button to start
8. Press STOP button to stop playback. Press the button to return to the folder menu.
Note:
1. The screen display will vary from disc to disc.
2. Pull out the USB or SD/MS/MMC card directly after the files are played. Then the unit will be in
disc playback again.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD System Setup
Preparations
1. Connect to the power supply and turn on the unit.
2. Press the SOURCE button to shift to DVD mode.
3. Press the SETUP button on the remote control to display the settings menu.
4. Press the
direction buttons on the remote control to select a category. All the items in the
category will appear on the screen.
5. Press the SETUP button again to exit the setup.
General Setup Page
Press the DVD SETUP button to enter the General setup menu. The screen will display as the
below:
- - General Setup Page - -
In the menu, Use the
select the desired Item. Press the ENTER button to
enter the item. Press the button to return.
direction buttons to
TV Display
Angle Mark
OSD Lang
Captions
Screen Saver
Last Memory
Media Center
Go To General Setup Page
TV Display
- - General Setup Page - -
1. Press the
direction buttons to select TV
TV Display
Angle Mark
OSD Lang
PS
On
Eng
Off
On
On
Normal/PS
Normal/LB
Wide
Display.
2. Press the ENTER button to enter the setup.
3. Use the direction buttons to select items.
Captions
Screen Saver
Last Memory
Media Center
4. Press the ENTER button again to confirm
selection and return.
Set TV Display Mode
Angle Mark
- - General Setup Page - -
1. Press the
Angle Mark.
2. Press the ENTER button to enter the setup.
direction buttons to select
TV Display
Angle Mark
OSD Lang
PS
On
Eng
Off
On
On
On
Off
Captions
Screen Saver
Last Memory
Media Center
3. Use the
Off.
direction buttons to select On or
4. Press the ENTER button again to confirm
selection and return.
Set Angle Mark
30
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD System Setup
OSD Lang
The item is used to select the OSD language.
- - General Setup Page - -
TV Display
Angle Mark
OSD Lang
PS
On
Eng
Off
On
On
1. Press the
direction buttons to select OSD
Lang.
English
French
Captions
2. Press the ENTER button to enter the setup.
3. Use the direction buttons to select items.
Screen Saver
Last Memory
Media Center
Spanish
German
Italian
4. Press the ENTER button again to confirm
selection and return.
Portuguese
Dutch
Set OSD Language
Captions
- - General Setup Page - -
1. Press the
direction buttons to select
Captions.
TV Display
Angle Mark
OSD Lang
PS
On
Eng
Off
On
On
2. Press the ENTER button to enter the setup.
3. Use the direction buttons to select items.
Captions
On
Off
Screen Saver
Last Memory
Media Center
4. Press the ENTER button again to confirm
selection and return.
Closed Captions
Screen Saver
- - General Setup Page - -
1. Press the
Screen Saver.
2. Press the ENTER button to enter the setup.
direction buttons to select
TV Display
Angle Mark
OSD Lang
PS
On
Eng
Off
On
On
Captions
3. Use the
Off.
direction buttons to select On or
Screen Saver
Last Memory
Media Center
On
Off
4. Press the ENTER button again to confirm
selection and to return.
Screen Saver
Last Memory
- - General Setup Page - -
1. Press the
direction buttons to select Last
TV Display
Angle Mark
OSD Lang
PS
On
Eng
Off
On
On
Memory.
2. Press the ENTER button to enter the setup.
Captions
3. Use the
Off.
direction buttons to select On or
Screen Saver
Last Memory
Media Center
On
Off
4. Press the ENTER button again to confirm
selection and return.
Set Last Memory State
31
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD System Setup
Media Center
- - General Setup Page - -
1. Press the
Media Center.
2. Press the ENTER button to enter the setup.
3. Use the direction buttons to select DVD,
USB, SD/MMC or MS.
direction buttons to select
TV Display
Angle Mark
OSD Lang
PS
On
Eng
Off
On
On
Captions
Screen Saver
Last Memory
Media Center
DVD
USB
4. Press the ENTER button again to confirm
selection and return.
SD/MMC
MS
DVD
Audio Setup Page
Press the SETUP button to enter the General setup menu, then use the
select Audio Setup Page, the screen will display as the below:
direction buttons to
direction buttons to
- - Audio Setup Page - -
In the menu, Use the
Dolby Digital Setup
HDCD
select the desired item. Press the ENTER button to
enter the item. Press the button to return.
Go To Audio Setup Page
Dolby Digital Setup
1. Press the
Dolby Digital.
direction buttons to select
- - Dolby Digital Setup - -
Dual Mono
Dynamic
Stereo
L-Mono
R-Mono
Mix-Mono
2. Press the ENTER button to enter the setup, the
screen will display as left:
3. In the menu, use the
select items.
direction buttons to
4. Press the ENTER button to enter the setup.
Press the button to return.
Dual Mono (1+1) Setup
Dual Mono
- - Dolby Digital Setup - -
1. Press the
direction buttons to select Dual
Dual Mono
Dynamic
Stereo
Mono.
L-Mono
R-Mono
Mix-Mono
2. Press the ENTER button to enter the setup.
3. Use the direction buttons to select items.
4. Press the ENTER button again to confirm
selection and return.
Dual Mono (1+1) Setup
32
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD System Setup
Dynamic
1. Press the
direction buttons to select
- - Dolby Digital Setup - -
Dynamic.
FULL
3/4
Dual Mono
Dynamic
Str
2. Press the ENTER button to enter the setup, the
screen will display as left:
3. Press the OK button to enter.
1/2
4. Use the
direction buttons to adjust.
1/4
5. Press the ENTER button again to confirm
setting and return.
OFF
Set Drc To Full
6. Press the
button to return.
HDCD Setup
In the Audio Setup Page, use the
direction buttons to select HDCD Setup. Press the ENTER
button to enter the setup and the screen will display as below:
- - Hdcd Setup Page - -
1. In the menu, press the ENTER button to enter
the setup.
Filter
1x
Off
1x
2x
2. Use the
direction buttons to select items.
3. Press the ENTER button again to confirm
selection and return.
4. Press the button to return.
Filter
Video Setup
Press the SETUP button to enter the General setup menu, then use the
direction buttons to
direction buttons to
select Video Setup Page, the screen will display as the below:
- - Video Setup Page - -
In the menu, Use the
Quality
select the desired item. Press the ENTER button to
enter the item. Press the button to return.
Go To Video Setup Page
Video Quality Setup
Select Quality, press the ENTER button to enter the menu as below:
- - Video Quality Setup - -
1. In the menu, Use the
direction buttons to
Sharpness
Brightness
Contrast
Med
00
High
select the desired item.
Medium
Low
00
2. Press the ENTER button to enter the item.
3. Press the button to return.
Sharpness
33
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD System Setup
Sharpness
- - Video Quality Setup - -
1. Press the
direction buttons to select
Sharpness
Brightness
Contrast
Low
00
High
Sharpness.
Medium
Low
00
2. Press the ENTER button to enter the setup.
3. Use the direction buttons to select High,
Medium or Low.
4. Press the ENTER button again to confirm
selection and return.
Sharpness
Brightness
1. Press the
direction buttons to select
Brightness.
2. Press the ENTER button to enter the setup, the
screen will display as left:
3. Use the
level.
direction buttons to adjust the
Brightness
0
4. Press the ENTER button again to confirm
setting and return.
Brightness
Contrast
1. Press the
direction buttons to select
Contrast.
2. Press the ENTER button to enter the setup, the
screen will display as left:
3. Use the
level.
direction buttons to adjust the
Contrast
0
4. Press the ENTER button again to confirm
setting and return.
Contrast
Preference Setup
Press the SETUP button to enter the General setup menu, then use the
direction buttons to
direction button to
select Preference Page, the screen will display as the below:
- - Preference Page - -
Audio
Eng
Off
In the menu, press the
Subtitle
Disc Menu
Default
enter the desired item. Press the ENTER button to
enter the item. Press the button to return.
Eng
Go to Preference Page
34
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD System Setup
Audio
- - Preference Page - -
1. Press the
direction buttons to select
Audio
Eng
Off
English
French
Audio.
Subtitle
Disc Menu
Default
Eng
Spanish
Chinese
Japanese
Italian
2. Press the ENTER button to enter the setup,
see the left figure:
3. Press the
direction buttons to select
Russian
German
audio language.
4. Press the ENTER button again to confirm
setting and return.
Preference Audio Language
Subtitle
Press the
direction buttons to select
1.
2.
3.
4.
- - Preference Page - -
Subtitle.
Audio
Eng
Off
French
Spanish
Chinese
Japanese
Italian
Subtitle
Disc Menu
Default
Press the ENTER button to enter the setup,
see the left figure:
Eng
Press the
direction buttons to select
Russian
German
Off
Subtitle language.
Press the ENTER button again to confirm
setting and return.
Preference Subtitle Language
Disc Menu
- - Preference Page - -
1. Press the
direction buttons to select Disc
Audio
Eng
Off
English
French
Menu.
Subtitle
Disc Menu
Default
2. Press the ENTER button to enter the setup,
see the left figure:
Eng
Spanish
Chinese
Japanese
Italian
3. Press the
direction buttons to select
Russian
German
Menu language.
4. Press the ENTER button again to confirm
setting and return.
Preference Menu Language
Default
- - Preference Page - -
1. Press the
direction buttons to select
Audio
Eng
Off
Subtitle
Disc Menu
Default
Default.
Eng
2. Press the ENTER button to select Reset.
3. Press the ENTER button, all the settings will
return to the default status.
Reset
Load Factory Setting
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
SYMPTOM
CHECK ITEM
Make sure disc tray is closed
Make sure disc is loaded in.
Make sure disc is loaded correctly.
The player cannot play.
Make sure disc is not dirty or warped.
Make sure the player’s region code is the same as region code
of DVD disc.
Make sure water condensation has not occurred.
Take out disc and leave the player on for at least one hour
when water condensation occurs.
Make sure system connection is correct.
Make sure the power of speakers is turned on.
Make sure the sound setup of DVD disc is correct.
Make sure disc is not dirty or warped.
Clean or replace the disc.
There is no sound.
Make sure the unit is turned on and is in correct video mode.
Make sure system connections are correct. If it is not, access
the setup menu and select the correct system.
There is no picture or the picture
moves up and down Unsteady.
Make sure it is not in A-B repeat status.
Press A-B button to cancel it.
Make sure disc is not dirty or damaged.
Clean the disc or skip selection.
Cannot continue to play and
play a section repeatedly.
Make sure there are no obstructions between the remote
control and the player.
Make sure the remote control is pointing at the player.
Make sure batteries are inserted and the polarity is correct.
Make sure battery is not weak.
The remote control does not
work.
Replace the weak battery.
Other Notes:
Static or other external interference may cause the player to behave abnormally. In this occurrence,
unplug the power-supply cord from the outlet and plug it in again to reset the player. If the problems
persist, then please disconnect the power and consult a qualified technician.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
TFT-LCD Resolution
TFT-LCD Screen Size
1440 x 900
19 inches
AC100~240V, 50/60Hz
DC 12V 5A
Power
Power Consumption
Dimension
< 60W
494mm x 184mm x 412mm (LxWxD)
About 9.2 Kg
Weight
Ambient Temperature
10~450C
DESIGN AND SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
Confidential unpublished works. © 1992 -1997 Dolby Laboratories, Inc.
All rights reserved.
All Images in this manual are only for your information.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
PALSONIC CORPORATION PTY LTD
1 JOYNTON AVENUE
WATERLOO NSW 2017 AUSTRALIA
TEL: (02) 9313 7111
FAX: (02) 9313 7555
PALSONIC CUSTOMER SERVICE
TELEPHONE
AUSTRALIA: 1300 657 888
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Miele Microwave Oven DA249 4 Alu User Manual
Miele Washer W 1945 User Manual
Milwaukee Cordless Drill 0726 20 User Manual
Mr Coffee Hot Beverage Maker HC4 User Manual
NordicTrack Treadmill NTL118061 User Manual
Nortel Networks Switch 8672A User Manual
Oki Printer ML184 User Manual
Omnimount TV Video Accessories ECHO63 User Manual
Omnimount TV Video Accessories TORINO36 User Manual
Panasonic Laptop CF 52EKM 1 D 2 M User Manual