MGW 2400
WMT Streaming Server
User's Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
Use the following safety guidelines to help protect your MGW
2400 unit from potential damage and to ensure your own
personal safety.
When using MGW 2400
As you operate MGW 2400, observe the following safety
guidelines
Note
Do not open the MGW 2400 unit, as this will void your warranty. MGW 2400
does not contain any user serviceable parts.
•
•
Before installing MGW 2400, unplug the system to help
prevent electric shock or system board damage. Certain
system board components continue to receive power any
time MGW 2400 is connected to AC power.
To help prevent electric shock, plug the power cable into
properly grounded sources. Use only properly grounded
extensions and adaptors as the need arises.
•
•
Use only a UL Recognized power cord.
Make sure nothing rests on your MGW 2400 power cable
and that the cables are not located where they can be
stepped or tripped over.
•
•
Do not spill food or liquids on your MGW 2400 unit.
Do not push any objects into free slots of your MGW 2400
unit. Doing so will damage your MGW 2400 unit and can
cause fire or electrical shock by shorting out interior
components.
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Keep your MGW 2400 unit away from radiators and heat
sources. Also, do not block cooling vents. Avoid placing
loose papers underneath your MGW 2400 unit. Do not
place your MGW 2400 unit in a closed-in wall unit or on a
bed, sofa, or rug.
When you disconnect a cable, pull on its connector or on its
strain relief loop, not on the cable itself. Some cables have a
connector with locking tabs; if you are disconnecting this
type of cable, press in on the locking tabs before
disconnecting the cable. As you pull connectors apart, keep
them evenly aligned to avoid bending any connector pins.
Also, before you connect a cable, make sure both
connectors are correctly oriented and aligned.
•
ESD Warning: Normal handling precautions should be
taken to avoid static discharge.
Download from Www.Somanuals.com. All Manuals Search And Download.
Compliance Information
FCC User Information
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance to the instruction manual, may cause harmful interference
to radio communication. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
NOTE: This product was FCC verified under test conditions that included the
use of shielded I/O cables and connectors between system components. To be
in compliance with FCC regulations, the user must use shielded cables and
connectors and install them properly.
Canadian Interference Statement
This Class A digital apparatus complies with Canadian ICES-003.
Download from Www.Somanuals.com. All Manuals Search And Download.
Declaration of Conformity
Manufacturer’s Name: Optibase Ltd.
Manufacturer’s Address: 7 Shenkar St., Herzliya 46120, Israel
Description of Equipment: MGW 2400 WMT Streaming Server with MGE-400D and
MGE-400 Encoders
Date of Issue: 2002
Directive Complied With: 89/336/EEC, 73/23/EEC, 93/68/EEC
Harmonized Standards to which Conformity is Declared:
•
•
•
•
•
EN 60950 Safety
EN 61000-3-2 Harmonic Current Emission
EN 61000-3-3 Flickermeter
EN 55022:1987 Class A Conducted and Radiated Emission
Immunity EN55024
•
•
•
•
EN 61000-4-2 ESD Contact/Air Discharge 4kV/8kV
EN 61000-4-3 Radiated Immunity 10V/m (27-1000Mhz, AM 1KHz 80%)
EN 61000-4-4 EFT&B 1kV 5/50nS, 5KHz rep.
EN61000-4-5 Surge Withstand (2kV common and 1kV differential mode
on AC line)
•
•
•
EN 61000-4-6 Current Injection Immunity 3 vrms
EN61000-4-8: Power Magnetic field (1 A/m 50Hz)
EN 61000-4-11 Voltage Dips Immunity
We, the undersigned hereby declare that the equipment specified above conforms to
the above Directive and Standards.
Manufacturer:
Full Name: Itzhak Keren
Position: Director Quality & Engineering
Place:
Israel
Date 11/7/02
Signature
Download from Www.Somanuals.com. All Manuals Search And Download.
Content
Introduction............................................................ 1
Overview.................................................................. 1
System Description .................................................. 2
System Overview.....................................................2
MGW 2400 Features ...............................................3
What’s in this Manual............................................... 4
Configuration & Installation.................................. 5
Overview.................................................................. 5
System Configuration............................................... 6
MGW 2400 Components.........................................6
Peripheral Components...........................................8
Getting Started......................................................... 9
Unpacking MGW 2400 ..........................................10
Power Supply ........................................................11
Servicing MGW 2400.............................................11
Hardware Overview ...............................................12
Connecting Peripherals - Encoders & Sources .....16
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Configuration ................................................ 20
Configuring HyperTerminal....................................20
DHCP enabled Networks.......................................22
Changing Passwords.............................................27
MGW 2400’s Network Settings..............................28
If DHCP is disabled – TCP/IP Settings..................34
MGW 2400 Utilities................................................39
Working with SCSI Disks.......................................41
Uploading Files......................................................44
Changing Settings from a Remote PC ................... 45
Operating MGW 2400........................................... 47
Overview................................................................ 47
Installing Software.................................................. 48
System Requirements ...........................................48
Configuring the Management PC for the Network.48
Installing the MGW 2400 EMS...............................49
Installing Microsoft Components............................52
Accessing MGW 2400............................................ 53
User Profiles..........................................................54
Logging on to MGW 2400......................................55
Viewing and Editing the List of Permitted Users....57
Viewing the List of Users Currently Logged On.....58
Logging off MGW 2400..........................................58
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Window Overview.......................................... 59
The Modules Page ................................................60
The Channels Page...............................................61
The Platform Page.................................................62
Toolbar and Displays.............................................66
Viewing and Setting Module Parameters ............... 67
I/O Parameters ......................................................67
Encoding Parameters............................................70
Tools......................................................................71
Editing the Channel Profile..................................... 72
Adding a Channel..................................................73
Editing an existing Channel...................................75
Removing Channels ..............................................75
Viewing the Channel Profile ..................................76
Managing Templates.............................................77
Managing Configurations.......................................79
Editing Channel Parameters .................................. 81
Encoding Parameters............................................81
Adjusting Video Parameters On The Fly ...............85
Target Parameters.................................................86
Operating Channels ............................................... 91
Receiving and Playing Back Streams....................92
Upgrading MGW 2400 ........................................... 94
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Specifications ..................................... 97
Chassis .................................................................. 97
Physical .................................................................97
Electrical Characteristics .......................................97
Input/Output Interfaces..........................................98
Environmental........................................................98
Safety Standards...................................................98
Management..........................................................99
Network Protocols .................................................99
Encoding Modules ............................................... 100
Physical Dimensions ...........................................100
Standard Compliance..........................................100
Input Signals........................................................100
Encoding Format .................................................100
Video Resolutions and Bit-Rates.........................101
Audio Modes and Bit-Rates.................................101
System Defaults................................................... 103
My System Settings ............................................. 103
User Names and Passwords................................ 104
MGW 2400 EMS Users .......................................104
MGW 2400 Administrator ....................................104
Troubleshooting................................................. 105
Hardware Errors................................................... 105
Errors while running MGW 2400 EMS ................. 108
Error Messages.................................................... 110
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Introduction
Overview
MGW 2400 is a multi-channel WMT encoding and streaming
server designed to enable the deployment of advanced streaming
media services over the broadband Internet and corporate
networks.
MGW 2400 encodes and streams up to six live Microsoft WMT
compliant streams over broadband terrestrial and wireless
networks such as xDSL, FTTx, satellite, cable, Ethernet LANs
and the Internet. It supports live WMT stream upload to
Microsoft Windows Media Server and IP multicast, unicast, UDP
and HTTP protocols, ensuring efficient transmission over a wide
range of networks. MGW 2400 encodes up to six live channels
concurrently at bit-rates between 64 kbps and 2 Mbps.
In this Chapter
•
System Description, page 2
What’s in this Manual, page 4
•
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 • System Description
System Description
MGW 2400 easily integrates with networking equipment and
complementary video equipment. This section describes MGW
2400 and its features.
System Overview
Figure 1: MGW 2400 in a Network
2400.
Computer
Task
Configuration PC
Connected
via RS-232
Initializes and reconfigures MGW
2400 using HyperTerminal.
Management Station
PC in the
network
Reconfigures MGW 2400 using
Telnet and operates it from MGW
2400 EMS.
The Management Station is referred
to as Management PC or Remote
PC.
Receiving Client
PC in the
network
Receives and plays back video and
audio using Windows Media Player.
Table 1: Computers serving and controlling MGW 2400
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 • System Description
MGW 2400 Features
•
•
Multi-channel rack-mount video streaming server.
Encodes, multiplexes and transmits up to 6 live Microsoft
WMT compliant streams.
•
•
Real-time uploading to a Windows Media Server.
Multiple multicast targets and on-demand live unicast
targets per channel.
•
•
•
•
Saves encoded streams to file.
SNMP management application.
Bit-rate adjustment on the fly.
Network traffic shaping (smoothing).
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 • What’s in this Manual
What’s in this Manual
This manual shows you how to use MGW 2400 as follows:
•
•
Chapter 1 presents an overview of MGW 2400.
Chapter 2 shows you how to install and configure MGW
2400.
•
•
•
Chapter 3 shows you how to install software and operate
MGW 2400.
Chapter 4 provides you with MGW 2400's technical
specifications.
Chapter 5 provides you with a troubleshooting guide.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
Configuration & Installation
Overview
MGW 2400 is a rack-mountable stand-alone server. Up to six
WMT encoding modules can be installed in MGW 2400's
chassis.
You may operate MGW 2400 from any PC on your network
that has the MGW 2400 EMS installed.
In this Chapter
•
System Configuration, page 6
•
•
•
Initial Configuration, page 20
Changing Settings from a remote PC, page 45
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • System Configuration
System Configuration
This section lists the MGW 2400 components. It also explains
and describes optional and required peripheral components,
which are not supplied by Optibase.
MGW 2400 Components
The following components are supplied by Optibase, if not
otherwise noted.
Component
Description
MGW 2400 chassis
'Housing' of the MGW 2400 system.
Power cord that fits your local
Din socket.
Connects to MGW 2400's power connector
(not supplied by Optibase).
Network cables - shielded
category 5
Connect MGW 2400's NIC A and B to two
different network segments
(not supplied by Optibase).
19", 23" or ETSI mounted
bracket
Rack-mounts MGW 2400.
RS-232 cable
SCSI disk
Connects PC to MGW 2400.
Connects to MGW 2400 and stores video
clips
(not supplied by Optibase).
Table 2: Chassis
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • System Configuration
Component
Description
MGE-400 encoding module
Module for WMT encoding from analog
sources.
MGE-400D encoding module
Video BNC cable
Module for WMT encoding from analog or
digital sources.
Connects a Composite Video source to
MGW 2400.
Low Loss Digital Video Belden
1694A cable
Connects an SDI source to MGW 2400.
S-Video MiniDIN cable
Audio Stereo MiniJack cable
RCA Coaxial cable
Connects an S-Video source to MGW
2400.
Connects an analog audio source to
MGW 2400.
Connects a digital audio source to MGW
2400.
Table 3: Encoding Modules
Component
Description
MGW 2400 Configuration Utility
Pre-installed software to configure MGW
2400.
MGW 2400 EMS
SNMP based Transmission management
software that you install on a PC on the
network. This PC is referred to as
Management PC.
Table 4: Software
Document
Description
MGW 2400 User’s Manual
Shows you how to install and operate
MGW 2400.
MGW 2400 EMS Help
Shows you how to use the MGW 2400
EMS. It installs together with the MGW
2400 EMS on the Management PC.
Table 5: Documentation
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • System Configuration
Peripheral Components
This section lists peripheral components that serve MGW 2400.
Optibase does not supply these components.
Hardware
Description
PC (Windows 2000 or XP) with
available COM1 port. This PC will
be referred to as Configuration PC.
Connects to MGW 2400 via RS-232 to
initialize and configure.
Management PC
(Windows 2000 or XP).
Reconfigures MGW 2400 using Telnet
and operates it from MGW 2400 EMS.
The Management Station is referred to
as Management PC or Remote PC.
Software
Description
External Windows Media Server.
Installed on a PC on the network,
broadcasts WMT streams received from
MGW 2400.
Windows Media Services 4.1.
Windows Media Player 9 Series.
Installed on a PC on the network,
manages and operates the Windows
Media Server.
Installed on a PC on the network,
receives and plays WMT streams.
Table 6: Peripherals
Note
Depending on available resources, you may use the same PC for MGW
2400's peripheral software components.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • Getting Started
Getting Started
This section describes how to unpack and start working with
MGW 2400.
•
•
•
To unpack and rack-mount MGW 2400, refer to page 10
For instructions on installing and removing encoding
modules and connect sources, refer to page 16.
•
•
•
For instructions on initializing MGW 2400, refer to page
For instructions on configuring MGW 2400 for the
For instructions on configuring MGW 2400's network
parameter settings if your network's DHCP is disabled, refer
•
•
For instructions on sharing a SCSI disk's drive with the
For instructions on configuring MGW 2400 by using
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • Getting Started
Unpacking MGW 2400
1. Choose a dry location for MGW 2400, which complies
with the requirements regarding temperature specified at
page 98.
2. Attach the rubber feet to MGW 2400 or rack-mount it into
a rack-mount chassis. To rack-mount MGW 2400, refer to
the following section.
Mounting MGW 2400 into a Rack
MGW 2400 can be used as a stand-alone device or rack-
mounted into a 19”, 23” or ETSI rack-mount chassis. To rack-
mount MGW 2400, do the following:
1. Remove the rubber feet from the bottom, if they have been
already attached.
2. Use the supplied screws to attach the brackets to the
corners of the MGW 2400 chassis.
3. Attach MGW 2400 to the rack-mount chassis.
Note
Disconnect the power cable from the power connector while mounting MGW
2400.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • Getting Started
Power Supply
MGW 2400 works with 90/260V AC. The power cord connects
to the power connector on MGW 2400’s rear panel. MGW 2400
recognizes your local voltage automatically.
MGW 2400 does not ship with a power cord. You will have to
purchase a power cord that fits your local DIN socket.
Servicing MGW 2400
MGW 2400 does not require any maintenance. If MGW 2400 is
in need of repair, you have to call for technical support. MGW
2400 does not contain parts, which you may service or repair by
yourself. Opening MGW 2400 will void your warranty.
To clean MGW 2400:
Clean MGW 2400 with a soft and dry rag only and do not open
the unit.
Note
Before performing any task on the MGW 2400 unit, switch MGW 2400 off
and disconnect the power cable to avoid accidents and electrical hazards.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • Getting Started
Hardware Overview
The following section provides you with a quick overview of
MGW 2400's hardware.
Front Panel
RJ-45 Ethernet Links
Alarm LED Power LED
optibase
ALARM
2
POWER
5
10
/
100 Base
T
10
/
100 Base
T
RS-232
MGW 2400
1
3
4
6
RS-232 Port
A
SCSI
B
Channels
SCSI Port
6 Channel LEDs
Figure 2: MGW 2400 Front Panel
Ports
Description
RS-232
Connects the Configuration PC to MGW
2400.
RJ-45 Ethernet Link A and B
Connects MGW 2400 to the network.
A connects NIC A
B connects NIC B.
SCSI Ultrawide II
Connects MGW 2400 to a basic type
SCSI disk. MGW 2400 does not
recognize SCSI disks with management
applications installed on them.
Table 7: MGW 2400 Front Panel
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • Getting Started
LEDs
Description
Power
Off
No power
Blinks green
Green
Booting
Power on
Alarm
Off
On
No error
At least one fan is running too
slowly or failed.
Ethernet Link
Off
Orange
No connection
Connected
Ethernet Transmit
(Channel) 1-6
Off
No transmission
Transmitting
Flashes green
Off
Empty slot
Blinks red
MGW 2400 is booting.
(if module inserted)
Slot error (software not loaded)
Green
Encoding module inserted and
ready to encode.
Blinks green
Red
Encoding
Encoding module inserted,
channel error.
Certain errors may cause this
LED to flash.
Table 8: MGW 2400 Front Panel LEDs
Note
To avoid damaging MGW 2400’s hardware, turn MGW 2400 off immediately
once the Alarm LED turns red.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • Getting Started
Rear Panel
Slots for six Encoding Modules
Power Switch
Fan
Power Connector
Figure 3: MGW 2400 Rear Panel
Ports
Description
Six slots
Install up to six encoding modules.
Power connector
Power switch
Connects the power cord.
Switches MGW 2400 on and off.
Table 9: MGW 2400 Rear Panel
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • Getting Started
Encoding Module
MGW 2400 supports MGE-400 and MGE-400D encoding
modules. MGE-400 encoding modules support analog sources
while MGE-400D encoding modules support both analog and
digital sources.
Figure 4: MGE-400D Encoding Module Interface
Connectors
Description
ANALOG AUD
DIG AUD
Connects analog audio source to MGW 2400.
Connects a digital audio source to MGW 2400. This
connector is only used for MGE-400D modules.
COMP.VID
S-VIDEO
SDI
Connects a Composite video source to MGW 2400.
Connects an S-Video Source to MGW 2400.
Connects a digital video source to MGW 2400. This
connector ships only with MGE-400D encoding
modules.
LEDs
Description
Source
Off
Green
Bad or no video source.
Video source detected.
Table 10: MGE-400 and 400D Encoding Module Interfaces
Note
MGE 400D encoding modules support the SMPTE 125M-1995 SDI standard.
Other SDI standards will cause the video frames to be shifted 10 lines down.
I.e. the content of the top 10 video lines is unknown and the 10 bottom lines
will not be encoded.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • Getting Started
Connecting Peripherals - Encoders & Sources
To install an encoding module:
1. Make sure that MGW 2400 is switched off and disconnect
the power cable.
2. Remove the slot cover of the free slot in which you want to
install an encoding module.
3. Firmly push the encoding module into the slot until you
hear a click. This may require some force. A correctly
inserted module should be completely flush with the rest of
the unit, and must not protrude at all from the slot.
4. Screw the module to MGW 2400's rear panel.
5. Connect video and audio sources to the encoding module
6. Switch MGW 2400 on again.
7. To add a new channel and set channel parameters, refer to
page 73.
Note
•
Do not install or remove encoding modules while running MGW 2400.
This will cause damage to your MGW 2400 chassis and encoding
modules.
•
•
Avoid touching inside free slots as this may cause electrical hazards
and damage your MGW 2400 unit.
The Source LED only turns green if a video source is connected to the
encoding module. If you only connect an audio source, the Source LED
remains off.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • Getting Started
To remove an encoding module:
1. Make sure that MGW 2400 is switched off and disconnect
the power cable.
2. Disconnect video and audio source cables.
3. Loosen the screws on the left and right side of the rear
panel and carefully pull the encoding module out of the
slot.
4. Screw the slot cover to MGW 2400’s rear panel.
5. Switch MGW 2400 on again.
Note
•
•
Do not install or remove encoding modules while running MGW 2400.
This will cause damage to your MGW 2400 chassis and encoding
modules.
Avoid touching inside free slots as this may cause electrical hazards.
Touching inside free slots may also damage your MGW 2400 unit.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • Getting Started
To connect a video source
•
Composite Video. Use the Video BNC cable (catalog
number BZA3636) as illustrated in Figure 5 to connect a
Composite video source to the COMP.VID connector.
Figure 5: The Video BNC Cable (BZA3636)
•
S-Video. Use the S-Video MiniDIN cable (catalog number
WCA2210) as illustrated in Figure 6 to connect an S-Video
source to the S-Video connector.
Figure 6: The S-Video MiniDIN Cable (WCA2210)
•
Digital Video. Use the Low Loss Digital Video Belden
1694A cable (catalog number WCA5971) to connect a
digital video source to the SDI connector. This connector
ships with MGE-400D encoding modules only.
Note
•
•
MGE 400D encoding modules support the SMPTE 125M-1995 SDI
standard. Other SDI standards will cause the video frames to be shifted
10 lines down. I.e. the content of the top 10 video lines is unknown and
the 10 bottom lines will not be encoded.
MGW 2400 does not support SECAM sources.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • Getting Started
To connect an audio source:
•
Analog audio. Use the Stereo MiniJack audio cable
(catalog number WCA2274) as illustrated in Figure 7 to
connect the audio source to the ANALOG AUD connector.
Figure 7: The Stereo MiniJack Audio Cable (WCA2274)
•
Digital audio. Use the RCA Coaxial cable (catalog number
WCA2199) as illustrated in Figure 8 to connect the audio
source to the DIG AUD connector.
Figure 8: The RCA Coaxial Cable (WCA2199)
Note
•
•
You can connect digital audio sources to MGE-400D encoding modules
only.
MGW 2400 does not support SECAM sources.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • Initial Configuration
Initial Configuration
To operate MGW 2400 for the first time, you use
HyperTerminal to log on to MGW 2400's Configuration Utility.
To log on to MGW 2400's Configuration Utility you use the
user name Administrator. The default password for this user is
Administrator.
Configuring HyperTerminal
HyperTerminal is pre-installed on PCs that run on Windows
NT, 2000 or XP. For further information on HyperTerminal,
refer to the Microsoft Windows documentation.
Optibase has provided you with pre-configured HyperTerminal
settings, which are available on MGW 2400's CD. To apply
these settings, do the following:
1. Use a serial cable to connect MGW 2400’s RS-232 port to
the Configuration PC's serial COM1 port.
2. Switch MGW 2400 on and wait until it finishes booting,
which is the case once the Power LED turns green. You
cannot apply the HyperTerminal settings before.
3. On MGW 2400's CD, go to HyperTerminal Settings and
copy MGW2400.ht to your Communication PC.
4. Right-click MGW2400.ht, choose Properties and clear
Read-Only.
5. Double-click MGW2400.ht; HyperTerminal appears and
you can log on to MGW 2400's Configuration Utility.
If you do not have the CD available, you have to manually
configure HyperTerminal for first use.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • Initial Configuration
To set communication parameters in HyperTerminal:
1. Open HyperTerminal and click Properties
in
HyperTerminal’s toolbar. The Properties screen appears.
2. From the Connect using list, choose COM1 to which you
will connect MGW 2400 and click Configure. The COM
Properties screen appears.
Figure 9: HyperTerminal’s COM Properties Screen
3. Enter the parameters into the respective fields as shown in
4. Click OK; HyperTerminal is now ready to communicate
with MGW 2400.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • Initial Configuration
DHCP enabled Networks
DHCP automatically provides TCP/IP settings for the NIC
connected to the respective DHCP enabled network.
In certain cases, you might want to assign unique IP addresses.
To change IP addresses, refer to your local network
administrator. For instructions on changing TCP/IP settings,
By default, NIC A is DHCP enabled and NIC B is DHCP
disabled.
To communicate with MGW 2400, you have to connect the
Configuration PC's COM1 port to MGW 2400’s RS-232 port.
The Configuration PC must have HyperTerminal installed. For
further information regarding the Configuration PC, refer to
page 2. To enable the Configuration PC to communicate with
MGW 2400, you have to first set the correct parameters for
HyperTerminal’s COM properties.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • Initial Configuration
To initialize MGW 2400 for the first time:
1. If you have not already done so, use a serial cable to
connect MGW 2400’s RS-232 port to the previously
chosen and configured serial COM1 port on the
Configuration PC.
2. Connect MGW 2400’s Ethernet links to two separate
network segments. Connecting both NICs to the same
network segment causes network conflicts.
3. To avoid network conflicts, make sure that you do not have
a network device with the hostname MGW2400 connected
to any of the relevant network segments.
4. Switch MGW 2400 on.
5. Start HyperTerminal and log on to MGW 2400’s
Configuration Utility as Administrator; MGW 2400
initializes. Administrator's default password is
Administrator.
•
If you connect a DHCP enabled network segment to
NIC A, TCP/IP settings are assigned automatically for
that NIC.
•
If you connect a network segment to NIC B or if the
network segment connected to NIC A is not DHCP
enabled, refer to page 34 for instructions on defining
TCP/IP settings for the relevant NIC.
6. Press any key to get to the Main menu.
Note
•
•
External WMS servers require networks that support 100Mbps Full
Duplex.
By default, DHCP is disabled for NIC B.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • Initial Configuration
Figure 10: Main Menu
Upon initializing, you must change MGW 2400’s hostname.
The hostname must consist of less than 15 characters. If you try
to enter more than 15 characters, you will receive an error
message.
To change MGW 2400’s hostname, follow the instructions at
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • Initial Configuration
To change MGW 2400’s hostname:
1. To avoid network conflicts, make sure that you don’t have
a network device with the desired new hostname already
connected.
2. Press 1 (Rename MGW 2400); you will be asked to
confirm your request to change MGW 2400’s hostname.
Figure 11: Change the Hostname
3. Press Y to confirm the request.
4. Type the new hostname for MGW 2400 and press Enter.
MGW 2400’s hostname changes. MGW 2400 only allows
hostnames consisting of less than 15 characters.
5. Make a note of MGW 2400’s new hostname for future
reference.
6. Press any key to return to the Main menu.
7. To restart MGW 2400, press 0 (Quit); you will be asked
whether you want to reboot now or later.
8. Press Y, the Logon prompt appears and MGW 2400
reboots, which may take several minutes. The booting is
completed when you hear a beep and the Power LED turns
green.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • Initial Configuration
9. To log on again, enter the username and password for
Administrator; the Main menu appears.
10. If you don’t want to log on again, terminate the connection.
MGW 2400 is now ready to use. For instructions on operating
MGW 2400, refer to chapter 3.
If you wish to change the hostname again at a later stage, log on
to MGW 2400 as Administrator and follow the instructions at
Note
•
•
Every network device (e.g. MGW 2400 unit) in a network must have a
different hostname. Two devices with the same hostname will conflict.
We strongly recommend that you make a note of your customized MGW
2400 settings for future reference. You can use the table at page 103
provided for your convenience.
•
It is necessary to restart MGW 2400 in order for changes to take effect.
We highly recommend you restart the system after exiting the
configuration utility, as prompted.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • Initial Configuration
Changing Passwords
MGW 2400 lets you define and change passwords for
Administrator. To define and change passwords, do the
following:
1. Log on to MGW 2400’s Configuration Utility as
Administrator; the Main menu appears.
2. Type 4 (Change Administrator Password); the Password
menu appears.
3. To change Administrator's password, press 1 and follow
the on-screen instructions.
4. Make a note of your new password.
5. To return to MGW 2400’s Main menu, press 0 (Return to
Main Menu).
6. To log off MGW 2400, press 0 (Quit); the Logon prompt
appears.
7. To log on again, type the user name and password for
Administrator; the Main menu appears.
8. If you don’t want to log on again, terminate the connection.
Note
We strongly recommend that you make a note of your passwords. You can
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • Initial Configuration
MGW 2400’s Network Settings
MGW 2400 comes with two network interface cards. To
increase performance, you can assign one network to manage
and configure MGW 2400, and the other one to transmit. MGW
2400 lets you change network settings for both network
interface cards.
Selecting the Network Mode
By default, both NICs are set to 100Mbps Full Duplex. If
relevant, you have to set the network mode for each NIC
separately.
To select the network mode:
1. Log on to MGW 2400’s Configuration Utility as
Administrator; the Main menu appears.
2. Press 2 (Change Network Settings); the Network menu
appears as illustrated in Figure 12.
3. To choose the network mode for NIC A, press 3; to choose
the network mode for NIC B, press 4; the Network Mode
4. Consult your network administrator before selecting one of
the displayed modes.
5. Press the respective number key to select the desired
network mode and follow the on-screen instructions; the
respective network mode is defined.
Note
•
•
You must set the network mode for each NIC separately.
Transmission to external WMS servers requires 100Mbps Full Duplex.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • Initial Configuration
6. To auto-select the network mode, press 5 (Auto Selection).
7. To return to the Network Mode Settings menu, press any
key.
8. To return to the Network menu, press 0 (Network Menu).
9. To select the network mode for the second NIC, repeat
steps 3 - 8.
10. To return to the Main menu, press 0 (Main Menu); MGW
2400 returns to the Main menu.
11. To log off MGW 2400, press 0 (Quit); you will be asked
whether you want to restart now or later.
12. To restart now, press Y; the Logon prompt appears and
MGW 2400 reboots, which may take several minutes. The
booting is completed when you hear a beep and the Power
LED turns green.
13. To log on again, type the username and password for
Administrator after MGW 2400 finished booting; the
Main menu appears.
14. To restart later, press N; the Logon prompt appears. You
will have to restart MGW 2400 at a later stage.
15. If you don’t want to log on again, terminate the connection.
To view the network mode and the network's speed:
•
On the Network menu, press 5 (View Network Adapters
Status); the network mode and speed display for both
network segments.
Note
It is necessary to restart MGW 2400 in order for changes to take effect. We
highly recommend you restart the system after exiting the configuration
utility, as prompted.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • Initial Configuration
Changing and adding DNS IP Addresses
MGW 2400 lets you set the IP addresses for multiple Default
Name servers (DNS) manually. You must enter all DNS IP
addresses, even if you want to add or update only one of them.
To view DNS options:
1. Log on to MGW 2400’s Configuration Utility as
Administrator; the Main menu appears.
2. Press 2 (Change Network Settings); the Network menu
appears.
3. In the Network menu, press 6 (Add or Remove DNS IP
Address); the DNS Options menu appears as illustrated
below and displays previously defined DNS IP addresses.
Figure 14: The DNS Options Menu
4. For instructions on adding or deleting DNS IP addresses,
5. To return to the Network menu, press 0 (Return to
Network Menu); MGW 2400 returns to the Network
menu.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • Initial Configuration
6. To return to the Main menu, press 0 (Main Menu); the
Main menu appears.
7. To log off MGW 2400, press 0 (Quit). If you added or
removed one or more DNS IP addresses, you will be asked
whether you want to restart now or later.
8. To restart now, press Y; the Logon prompt appears and
MGW 2400 reboots, which may take several minutes. The
booting is completed when you hear a beep and the Power
LED turns green.
9. To log on again, type the username and password for
Administrator; the Main menu appears.
10. To restart later, press N; the Logon prompt appears. You
will have to restart MGW 2400 at a later stage.
11. If you don’t want to log on again, terminate the connection.
Note
•
•
You should set at least one DNS IP address.
We recommend that you make a note of all DNS IP addresses you set.
You can use the table provided at page 103 for your convenience.
•
It is necessary to restart MGW 2400 in order for changes to take effect.
We highly recommend you restart the system after exiting the
configuration utility, as prompted.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • Initial Configuration
To add DNS IP addresses:
1. To add a DNS IP address, press 1 (Add DNS IP Address);
you will be asked to enter the first DNS IP address.
2. Type the desired IP address and press Enter; the desired
DNS IP address is added; you will be asked to enter the
second DNS IP address.
3. To add more DNS IP addresses, repeat step 2 for each
DNS IP address you want to add. You can add up to five
DNS IP addresses.
4. If you don’t want to add more DNS IP addresses, press
Enter without typing a DNS IP address; MGW 2400
returns to the DNS Options menu.
To delete DNS IP addresses:
1. To delete a DNS IP address, press 2 (Delete DNS IP
Address); you will be asked to enter the associated number
key for the first DNS IP address you want to delete.
2. Press the associated number key for the DNS IP address to
delete and press Enter; the desired DNS IP address is
deleted and you will be asked to enter the second DNS IP
address to delete.
3. To delete more DNS IP addresses, repeat step 2 for each
DNS IP address you want to delete.
4. If you don’t want to delete more DNS IP addresses, press
Enter; MGW 2400 returns to the DNS Options menu.
5. To delete all DNS IP addresses, press 3 (Delete all DNS IP
Addresses) and confirm your request; all DNS IP
addresses are deleted.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • Initial Configuration
If DHCP is disabled – TCP/IP Settings
If the relevant NIC or network segments are not DHCP enabled,
you have to edit TCP/IP settings manually when logging on for
the first time. If desired, you may disable DHCP and set or
change TCP/IP settings manually.
You disable DHCP and/or edit TCP/IP settings as explained
below.
To choose a NIC and disable DHCP:
1. Log on to MGW 2400’s Configuration Utility as
Administrator; the Main menu appears.
2. Press 2 (Change Network Settings); the Network menu
appears.
3. To edit TCP/IP settings for NIC A, press 1, or for NIC B,
press 2; DHCP options appear for the NIC you chose.
4. Type 2 (Disable DHCP and set TCP/IP parameters
manually); DHCP is disabled and TCP/IP options appear
as illustrated in Figure 15.
5. To define or change the chosen NIC's TCP/IP settings,
refer to the next page.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • Initial Configuration
To define or change TCP/IP settings:
1. Enter the new IP address and Subnet mask for the relevant
NIC and press Enter. Make sure that each NIC’s IP
address belongs to a different subnet.
2. To make MGW 2400 accessible from outside your local
network for the relevant NIC, define the Default Gateway
server's IP address and press Enter.
3. If you do not want MGW 2400 to be accessible from
outside your local network via the relevant NIC, type 0 for
Default Gateway and press Enter; the new parameters for
the relevant NIC are defined and MGW 2400 returns to the
Network menu.
4. To register MGW 2400 in the WINS data base, enter the
WINS server's IP address and press Enter. If you do not
want to define a WINS server or no WINS server exists in
your network, type 0 and press Enter.
Make sure that you do not press Enter without typing any
value as this could cause MGW 2400 to fail.
Figure 15: Define TCP/IP Settings for NIC A
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • Initial Configuration
5. Make a note of your settings of your TCP/IP settings upon
your convenience
6. To define or change TCP/IP settings for the second NIC,
follow the instructions on the previous page again.
7. To return to the Main menu, press 0 (Main Menu).
8. To log off MGW 2400, press 0 (Quit); you will be asked
whether you want to restart now or later.
9. To restart MGW 2400 now, press Y; the Logon prompt
appears and MGW 2400 reboots, which may take several
minutes. The booting is completed when you hear a beep
and the Power LED turns green.
10. To log on again, type the username and password for
Administrator; the Main menu appears.
11. To restart MGW 2400 later, press N; the Logon prompt
appears. You will have to restart MGW 2400 manually at a
later stage.
12. If you don’t want to log on again, terminate the connection.
MGW 2400 is now ready to start operating. For instructions on
operating MGW 2400, refer to chapter 3.
Note
It is necessary to restart MGW 2400 in order for changes to take effect. We
highly recommend you restart the system after exiting the configuration
utility, as prompted.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • Initial Configuration
Displaying TCP/IP Settings
MGW 2400 lets you view the TCP/IP settings for both NICs.
To view TCP/IP settings, do the following:
1. If you changed TCP/IP settings, make sure that you first
restart MGW 2400; otherwise you will not be able to view
them.
2. Log on to MGW 2400’s Configuration Utility as
Administrator; the Main menu appears.
3. Press 3 (Display TCP/IP Settings); MGW 2400’s TCP/IP
settings display for both NICs.
4. Press any key to return to the Main menu.
Figure 16: Displaying the TCP/IP settings for NIC A and B
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • Initial Configuration
Restoring Default Settings
In some cases, you may wish to restore MGW 2400’s default
settings. MGW 2400 lets you restore the default of network
settings and the hostname as follows:
1. Make sure that MGW 2400’s default settings won’t cause
network conflicts.
2. Log on to MGW 2400’s Configuration Utility as
Administrator; the Main menu appears.
3. Press 5 (Restore Default Settings) and confirm your
request; MGW 2400 restores the default settings. If you
don’t want MGW 2400 to restore default settings, press N.
4. Press any key to return to the Main menu.
5. To log off MGW 2400, press 0 (Quit); you will be asked
whether you want to restart now or later.
6. To restart now, press Y; The Logon prompt appears and
MGW 2400 reboots, which may take several minutes. The
booting is completed when you hear a beep and the Power
LED turns green.
7. To log on again, type the username and password for
Administrator; the Main menu appears.
8. To restart later, press N; the Logon prompt appears. You
will have to restart MGW 2400 at a later stage.
9. If you don’t want to log on again, terminate the connection.
Note
•
•
The password does not reset to default.
If your network is not DHCP enabled, you will have to manually redefine
the TCP/IP settings.
•
It is necessary to restart MGW 2400 in order for changes to take effect.
We highly recommend you restart the system after exiting the
configuration utility, as prompted.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • Initial Configuration
MGW 2400 Utilities
This section instructs you how to set the time and date. It
explains how to manage a SCSI disk from MGW 2400’s
configuration and how to enable FTP mode for maintenance
purposes.
Setting Time and Date
MGW 2400 lets you set the time and date. To set the time and
date, do the following:
1. Log on to MGW 2400’s Configuration Utility as
Administrator; the Main menu appears.
2. Press 6 (Utility Menu); the Utility menu appears.
Figure 17: MGW 2400’s Utility Menu
3. Press 2 (Set Time and Date); the Set Time and Date menu
appears.
4. Press 1 (To Update Time and Date) and follow the on-
screen instructions; the time and date are updated.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • Initial Configuration
5. To synchronize MGW 2400 to the network time, press 2
(To Synchronize Time and Date with Server), type the
time server’s hostname upon instruction to do so and press
Enter; MGW 2400 synchronizes to the network time.
6. Press any key to return to the Set Time and Date menu.
7. To return to the Utility menu, press 0 (Utility Menu); the
Utility menu appears.
8. To return to the Main menu, press 0 (Main Menu); the
Main menu appears.
9. To log off, press 0 (Quit); the Logon prompt appears.
10. To log on again, type the username and password for
Administrator; the Main menu appears.
11. If you don’t want to log on again, terminate the connection.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • Initial Configuration
Working with SCSI Disks
MGW 2400 requires a SCSI disk to save streams to file. MGW
2400 is equipped with an Ultrawide SCSI port, which can
connect to SCSI disks.
To prepare and connect a SCSI disk:
1. Format the SCSI disk on a separate PC in NTFS or FAT
(not FAT32) format. If you wish, you can divide the SCSI
disk into several partitions.
2. Create folders on the SCSI disk using the DOS-Shell
command MD. Copy clips to the SCSI disk. You may
delete unused folders by using the DOS-Shell command
RD.
3. Make sure that MGW 2400 is switched off.
4. Connect the accordingly prepared SCSI disk to MGW
2400’s SCSI port.
5. Switch MGW 2400 on again; MGW 2400 is now ready to
transmit prerecorded clips. The SCSI disk's default drive is
drive D. Additional SCSI disk partitions are labeled in
alphabetical order starting with drive E.
For instructions on sharing SCSI disk partitions, refer to
page 42.
Note
Remember that you may log on to MGW 2400 from the Configuration PC via
RS-232 or from any computer on the network via Telnet.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • Initial Configuration
To enable Share access for SCSI disk partitions:
1. Log on to MGW 2400’s Configuration Utility as
Administrator; the Main menu appears.
2. Press 6 (Utility Menu); the Utility menu appears.
3. Press 3 (Enable Share Access to SCSI Disk Partitions)
the partitions you entered can be accessed from the
network.
Figure 18: Enable Share Access for SCSI Disk Partitions
4. To return to the Main menu, press 0 (Return to Main
Menu).
5. To log off MGW 2400, press 0 (Quit); the Logon prompt
appears.
6. To log on again, type the username and password for
Administrator; the Main menu appears.
7. If you don’t want to log on again, terminate the connection.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • Initial Configuration
To disable Share access for SCSI disk partitions:
1. Log on to MGW 2400’s Configuration Utility as
Administrator; the Main menu appears.
2. Press 6 (Utility Menu); the Utility menu appears.
3. Press 4 (Disable Share Access to SCSI Disk Partitions)
and enter the desired partitions; the desired partitions
cannot be accessed from the network.
4. To return to the Main menu, press 0 (Return to Main
Menu).
5. To log off MGW 2400, press 0 (Quit); the Logon prompt
appears.
6. To log on again, type the username and password for
Administrator; the Main menu appears.
7. If you don’t want to log on again, terminate the connection.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • Initial Configuration
Uploading Files
To replace or add files for maintenance purposes, MGW 2400
allows you to transfer files to the disk via FTP. To transfer files,
do the following:
1. Log on to MGW 2400’s Configuration Utility as
Administrator; the Main menu appears.
2. Press 6 (Utility Menu); the Utility menu appears.
3. On the Main menu, press 1 (FTP Mode); the FTP prompt
appears.
4. Follow the instructions provided by Optibase.
Note
The FTP option has been provided for maintenance procedures only. We
strongly recommend that you do not add, delete or replace any files on your
own as this will void your warranty and may cause MGW 2400 to fail.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • Changing Settings from a Remote PC
Changing Settings from a Remote PC
After initializing MGW 2400 for the first time, you can perform
changes from any computer in your network by using Telnet.
Telnet is pre-installed on any PC running Windows and usually
resides in the system folder.
To make MGW 2400 accessible from outside your local
network, you must define a Default Gateway. To define the
Default Gateway, refer to your local network administrator.
To install Telnet on a separate PC:
1. Choose Start >> Find >> Files or Folders.
2. Type Telnet.exe into the Names field.
3. Create a shortcut to the displayed file on the Desktop.
To change MGW 2400 settings from a Remote PC:
1. Double-click the Telnet icon on the Desktop.
dialog box appears.
3. Make sure you enter the parameters as illustrated below
and click Connect.
HostName: [Hostname or IP address of MGW 2400]
Port: telnet
TermType: vt100
4. Log on to MGW 2400’s Configuration Utility as
Administrator; the Main menu appears.
5. Proceed as described at page 25. Some changes require
MGW 2400 to restart in order to take effect. If changes
require MGW 2400 to restart, you will be asked whether
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 • Changing Settings from a Remote PC
you want to restart now or later upon logging off MGW
2400.
6. To restart now, press Y; MGW 2400 logs off and reboots,
which may take several minutes. Log on again with the
new parameters to confirm that the requested changes have
been made.
7. To restart at a later stage, press N; MGW 2400 logs off.
Make sure that MGW 2400 will be restarted as soon as
possible for changes to take effect.
8. To log off without performing any task, press 0 (Quit).
MGW 2400 is now ready for use. For instructions on operating
MGW 2400, refer to chapter 3.
Note
•
•
We strongly recommend that you make a note of your new network
settings; otherwise you may not be able to log on again. You can use
the table provided at page 103 for your convenience.
It is necessary to restart MGW 2400 in order for changes to take effect.
We highly recommend you restart the system after exiting the
configuration utility, as prompted.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Operating MGW 2400
Overview
MGW 2400 is a rack-mountable stand-alone server. Up to six
WMT encoding modules can be installed in MGW 2400's
chassis.
You may operate MGW 2400 from any PC on your network
that has the MGW 2400 EMS installed.
In this Chapter
•
•
•
•
•
•
•
•
Accessing MGW 2400, page 53
Main Window Overview, page 59
Viewing and Setting Module Parameters, page 67
Editing the Channel Profile, page 72
Editing Channel Parameters, page 81
Operating Channels, page 91
Upgrading MGW 2400, page 94
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Installing Software
Installing Software
This section instructs you on configuring your Management PC
and installing the MGW 2400 EMS.
System Requirements
•
•
Pentium-III PC 500 MHz or higher with one 10/100BT
network interface card (NIC) installed.
If your PC has more than one NIC installed, use the
Add/Remove Hardware wizard to disable the additional
NICs.
MGW 2400 currently supports the following operating
systems:
•
Windows 2000 Professional with Service Pack 4 or
higher.
•
Windows XP Professional with Service Pack 1 or
higher.
•
•
128 MB RAM or more, depending on the number of MGW
2400 units you manage from the relevant PC.
100 MB virtual memory or higher. For instructions on
setting virtual memory on your PC, refer to the relevant
Microsoft Windows documentation.
•
•
200 MB free disk space or more.
CD-ROM drive (16× or faster)
Configuring the Management PC for the Network
•
•
Go to My Network Places and then to Local Area
Connection.
Refer to the relevant Microsoft Windows documentation for
further instructions.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Installing Software
Installing the MGW 2400 EMS
The MGW 2400 EMS installs together with Java Runtime
1.3.1_03. Make sure to uninstall any previous version of MGW
2400 EMS before you install the new version.
To uninstall MGW 2400 EMS:
•
Use the Add Or Remove Programs wizard in the Control
Panel and follow the onscreen instructions.
To install MGW 2400 EMS:
1. Close all programs and insert the MGW 2400 CD into your
PC's CD ROM drive.
2. On the MGW 2400 CD, navigate to the EMS folder;
installation files appear.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Installing Software
3. Double-click setupwin32.exe and follow the on-screen
instructions.
•
You will be asked whether you wish to edit the default
IP address 127.0.0.1 specified for MGW 2400 EMS.
We recommend setting it to the IP address associated
with the unit mostly used.
•
If you are asked whether you want the MGW 2400
EMS to overwrite an already installed version of the
Java Virtual Engine, choose Yes. If you choose No,
the installation may fail.
The MGW 2400 EMS is installed and a shortcut is added
to your Desktop.
Figure 19: MGW 2400 EMS Shortcut
When you open the MGW 2400 EMS, the MGW 2400
EMS Logon window appears with the default IP address
127.0.0.1 or with the IP address that you defined, for
example 172.16.100.137.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Installing Software
To edit the default IP address at a later stage:
1. Make sure that you close the MGW 2400 EMS.
2. Browse the MGW 2400 EMS folders for EMSConfig.ini
and create a backup. Save the backup in a different folder
on your PC.
3. Open EMSConfi.ini; the first line reads for example
ems2400.snmp.deviceIP 172.16.100.137.
4. Change the registered IP address to the desired IP address.
5. Save and close EMSConfig.ini; the MGW 2400 EMS
displays the new IP address once the MGW 2400 EMS
Logon window appears.
Note
•
Make sure that only one NIC is enabled on the Management PC,
otherwise the MGW 2400 EMS cannot communicate properly with MGW
2400.
•
•
•
To install a new version of MGW 2400 EMS at a later stage, first
uninstall the current version of MGW 2400 EMS.
If the available disk space is insufficient, installing MGW 2400 EMS will
fail.
If you want to uninstall the MGW 2400 EMS after you edited
EMSConfig.ini, you will have to manually delete the MGW 2400 folder.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Installing Software
Installing Microsoft Components
In order to use an external WMS server and receive WMT
streams, you have to download and install Microsoft's Windows
Media Services and Windows Media Player respectively. You
may install Windows Media Services and Windows Media
Player on the same PC as MGW 2400 EMS, if desired.
To download and install Windows Media Services 4.1:
•
Refer to Microsoft's website at
http://www.microsoft.com/windows/windowsmedia/
Services from the list. The file you download is called
wmserver.exe.
•
For instructions on installing and using the Windows Media
Administration component, follow the onscreen
instructions.
To download and install Windows Media Player 9:
•
Refer to Microsoft's website at
9series/player.aspx and follow the onscreen instructions to
download and install Windows Media Player 9 Series for
your operating system.
•
For Windows XP, the file you download is called
MPSetupXP.exe.
•
For Windows 2000, the file is called MPSetup.exe.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Accessing MGW 2400
Accessing MGW 2400
You manage MGW 2400 from MGW 2400 EMS, an SNMP
based management application installed on a PC on the
network. The MGW 2400 EMS allows you to remotely add,
edit and remove channels associated with installed hardware.
Before starting to operate MGW 2400, you must log on to
MGW 2400.
•
For permitted user profiles and associated user rights, refer
•
•
To log on to MGW 2400, refer to page 55.
To view and edit the list of users currently logged on, refer
•
To log off MGW 2400, refer to page 58.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Accessing MGW 2400
User Profiles
MGW 2400 ships with three default users configured, each one
associated with a certain user profile as listed below. The
password for the default users is optibase.
You can add, edit and delete additional users associated with
specific to the MGW 2400 unit to which you log on.
Up to ten users can access MGW 2400. The same user can log
on once at a time from the same Management PC and up to five
times from different Management PCs.
Profile
Guest
User
User Rights
Comments
guest
9 Guests and
one Super
User or
Administrator,
or 10 Guests
can log on at a
time.
•
•
Views channel parameters
and profile.
Views the list of users
allowed to log on to this
unit.
•
Views the list of users
currently logged on to this
MGW 2400 unit.
Administrator
admin
All Guest rights
One
Administrator
or Super User
can log at a
time.
•
•
Sets channel parameters.
Adds and removes
channels.
•
Starts and stops playing
channels.
Super User
super
All Administrator rights
One Super
User or
Administrator
can log at a
time.
•
Adds, edits and removes
users allowed to log on to
this MGW 2400 unit.
•
•
Logs off users currently
logged on to MGW 2400.
Restarts MGW 2400.
Table 11: MGW 2400 User Profiles
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Accessing MGW 2400
Logging on to MGW 2400
Up to ten users associated with three different user profiles can
access MGW 2400. The same user can log on once from the
same Management PC and up to five times from different
Management PCs.
Users can log on via NIC A or NIC B depending on the
configuration and which one is used first. MGW 2400 allows
EMS access via one NIC only, which is determined by the first
user that logs on.
1. On MGW 2400's Management PC, go to the Start menu
and choose MGW 2400 EMS; the Login window appears.
Figure 20: MGW 2400's Logon Window
2. In the Device IP/Name field, enter the relevant MGW 2400
unit's IP address.
•
To scan the network for available units, click
Discover ; units available in the Management
PC's workgroup and VLAN appear in the Discover
list.
•
To choose one of the listed units, click the line
displaying the desired unit; the Login window appears
and displays the associated unit's IP address.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Accessing MGW 2400
3. From the Privileges list, choose the desired user profile.
4. Enter the user name and password for the desired user and
click OK ; the MGW 2400 EMS Main window
appears with the Modules page open. The IP address of the
unit appears in the Status bar to the left and the current user
level to the right.
•
•
For required passwords, refer to page 104.
The blue arrow to the upper right
and the
green LED in the Status bar indicate that MGW 2400
is responding properly.
Logging on to a different Unit or as a different User
If the arrow is broken and turned red
; you cannot use
Re-Login. In this case, first close MGW 2400 EMS and then
log on to a different unit.
1. On MGW 2400 EMS's toolbar, click Re-Login
the Login window appears.
;
2. In the Device IP/Name field, enter the relevant MGW 2400
unit's IP address.
•
To log on to the same unit as a different user, leave
the IP address as is and choose the desired user from
the Privileges list.
3. Refer to the previous page for further information and
instructions.
Note
If you try to log on as Administrator or Super User and there is
already an Administrator or Super User logged on, MGW 2400 logs
you on as Guest.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Accessing MGW 2400
Viewing and Editing the List of Permitted Users
•
To edit the list of permitted users, you must be logged on as
Super User. To log on as Super User, refer to the previous
pages for instructions.
•
To view the list of permitted users, in the MGW 2400 EMS
Menu bar, go to Login and then to Users/Permissions
Table; the currently defined users appear. For information
•
To add a user, click Add
profile and enter the desired user name and password; the
new user is added.
, choose the desired user
•
•
To edit a user, select the desired user, click Edit
and change the user profile, user name and/or password as
desired.
To remove a user, select the desired user and click Del
; the selected user is deleted.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Accessing MGW 2400
Viewing the List of Users Currently Logged On
•
In the MGW 2400 EMS Menu bar, go to Login and then to
Current Users Table; the current users appear with their
Management PC's or user group's IP address. This list also
displays each user's logon time.
Forcing a User off MGW 2400
•
To log off a user, you must be logged on as Super User. To
log on as Super User, refer to the previous pages for
instructions.
•
Right-click the desired user in the Current User Table and
choose Force Logout from the Shortcut menu; the
respective user is notified that he has been logged off.
Logging off MGW 2400
•
In the Title bar of the MGW 2400 EMS window, click
Close and confirm your request; MGW 2400 logs off and
the MGW 2400 EMS window closes.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Main Window Overview
Main Window Overview
The Main window lets you view and set module, channel,
platform and WMS configurations. By default, the MGW 2400
EMS Main window appears with the Modules page open.
•
•
•
•
•
For the Channels page, refer to page 61.
For the Platform page, refer to page 62.
For the External WMS page, refer to page 64.
For the toolbar and displays, refer to page 66.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Main Window Overview
The Modules Page
Figure 21: Modules Page with six Encoding Modules
LEDs
LED Status Description
Green
Red
MGW 2400 responding
MGW 2400 not responding or switched off.
Off
No error
Red
At least one fan is running too slowly or failed.
Off
No channel configured or slot empty
Channel ready
Orange
Green
Red
Channel encoding
Channel error
Off
No source
Green
Source connected
Green
Yellow
Network connected
No network connected or network error
Green
Red
The fans are running properly.
At least one fan is running too slowly or has
failed.
Table 12: Modules Page - LEDs
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Main Window Overview
The Channels Page
Figure 22: Channels Page with one Channel
Buttons
Description
Opens the Channel wizard to add a channel.
Opens the Parameter window to edit an existing channel.
Opens the Parameter window to view channel parameters.
Removes selected channels.
Saves a channel as template.
Selects all channels for playing, stopping or removing
channels.
Plays selected channels.
Stops selected channels.
Opens related help topic.
Table 13: Channels Page
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Main Window Overview
The Platform Page
Figure 23: Platform Page
Unit Parameters
Parameters Settings
Comments
Description
Up Time
MGW 2400's Version
Time since last switching
on or restarting MGW
2400.
To update the displayed time,
click Refresh
.
Name
MGW 2400's hostname
Displays MGW 2400's host-
name. To change the hostname,
refer to page 25 for instructions.
Location
Physical location
Not used.
Table 14: Platform Page - Unit Parameters
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Main Window Overview
MGW Monitoring
Parameter
Comments
Total Bit-Rate
Bit-rate of all streams transmitted by MGW 2400.
Number of multicast streams transmitted.
Number of Stations
Aggregated Send Rate Total bit-rate of unicast streams transmitted.
Number of Unicast
Streams
Number of unicast clients connected to MGW 2400.
CPU Usage
MGW 2400's CPU usage in percent.
Table 15: Platform Page - MGW Monitoring
NIC Table
Parameter
Settings
Description
Index
1
2
Refers to NIC A
Refers to NIC B
IP Address
NIC A and B's
IP addresses
You use the Configuration Utility to
change MGW 2400's IP addresses.
Subnet Mask
NIC A and B's
subnet masks
You use the Configuration Utility to
change MGW 2400's subnet masks.
Table 16: Platform Page - NIC Table
Tools
Buttons
Description
Not used.
Updates parameters displayed.
Restarts MGW 2400.
Opens related help topic.
Table 17: Platform Page - Tools
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Main Window Overview
The External WMS Page
Figure 24: External WMS Page
Servers
•
To add or edit an external WMS server, go to the External
WMS page, select a list entry and type or change the IP
address, user name and password as required and click
Apply
; the desired server is added to the list. An
external WMS server must belong to the same workgroup
as MGW 2400.
•
•
To select an existing WMS server for transmission, go to
the Target page and choose the desired server from the
External WMS list. Refer to page 86 for instructions.
To remove an existing server, select the relevant servers
table entry, delete the IP address and click Apply
;
the relevant server is removed.
•
If no servers are configured, server table entries display Not
Configured.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Main Window Overview
Server Properties
Buttons
Settings
Description
Server Name
An external WMS
server's IP address.
If no server has been
configured in the
selected Servers Table
entry, this field displays
Not Configured.
User Name
Password
User name (if
Empty, if no server
selected or no user
name required.
required) to access
the relevant external
WMS server.
Password (if required) Empty, if no server
to access the relevant
external WMS server.
selected or no password
required.
MGW Transmission NIC
IP addresses of MGW Select the desired MGW
2400's NIC A and B
2400 NIC for
transmitting content to
the external WMS
server.
Table 18: External WMS Page
Buttons
Description
Adds external WMS server to the list and makes it
available.
Opens related help topic.
Table 19: External WMS Page
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Main Window Overview
Toolbar and Displays
The Main window's Menu and Status bars are available from
the Modules, Channels, Platform and External WMS pages. The
following table explains available options.
Toolbar
Description
Opens the Login window to log on to a different unit
or as a different user.
Opens the Configuration manager and lets you save
your current configuration.
Opens the Channel wizard and lets you add a
channel.
Opens the Software Version manager and lets you
add, activate and remove software versions.
Opens the Template manager and lets you view,
add and remove channel templates.
Opens the MGW 2400 EMS help file. The MGW
2400 EMS help file requires an Internet browser and
has been optimized for Internet Explorer 5.x.
Status Buttons
Status Bar
Description
MGW 2400 is responding properly.
MGW 2400 has been switched off or is not
responding.
Description
The IP address of the MGW 2400 unit that you are
logged on to.
Your current user profile.
Table 20: Options and Status Buttons
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Viewing and Setting Module Parameters
Viewing and Setting Module Parameters
To access the desired encoding module's parameters, click the
associated image in the Modules page.
I/O Parameters
Figure 25: Encoding Module - I/O Parameters
Video
Settings
Comments
Source
Composite
Analog video signal that combines
all the components in one signal.
S-Video
SDI
Analog video signal that carries
separate luminance and chroma
signals.
Digital video signal, available for
MGE-400D encoding modules.
Color System
Input Detect
NTSC, PAL,
Auto Detect
Determines the color system.
MGW 2400 and your source
device must be set to the same
color system parameter. If you
choose Auto Detect, MGW 2400
automatically detects the correct
color system.
No source
Source detected
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Viewing and Setting Module Parameters
Video
Settings
Comments
Color Sys Detect
NTSC, PAL, N/A
If you choose Auto Detect, this
field displays the correct color
system.
This field displays N/A if the color
system could not be recognized or
no source is connected.
This field does not show if you
manually choose the color system.
Sharpness Filter
Contrast
Level 0 - 15
(default is Level 6)
Filters high frequencies in the
picture's black-and-white portion
out to obtain a sharper picture.
0 - 255
(the default is 128)
Adjusts the polarity between white
and black in the video signal. If
white is very distant from black, a
signal has high contrast. If white is
closer to black, a signal has low
contrast causing it to appear with a
gray tone. Adjusting the contrast
changes the relation between the
color steps.
Hue
0 - 255
(the default is 128)
Adjusts the wavelength of the base
colors (i.e. red, green, yellow) in a
NTSC video signal. Adjusting the
hue creates linear change in the
phase of all the colors. If your
video source is PAL, this option
does not show.
Brightness
Saturation
0 - 255
(the default is 128)
Adjusts the amount of light emitted
in the video signal.
0 - 255
(the default is 128)
Adjusts the amount of color in the
signal.
Table 21: Encoding Module - Video IO Parameters
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Viewing and Setting Module Parameters
Audio
Settings
Comments
Audio Source
Unbalanced
Analog audio source that has a
single voltage relative to ground
or common.
AES/EBU
Digital audio source, available
with MGE-400D encoding
modules.
Sample Rate
32, 44.1, 48 kHz
Determines how many audio
samples are collected per
second while capturing the
audio stream. This parameter
affects the quality. There is no
set rule for the right choice.
Only trial and error determines
the best result for your needs.
Digital audio sources must be
composed at a sample rate of
32, 44.1 or 48 kHz.
Table 22: Encoding Module - Audio I/O Parameters
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Viewing and Setting Module Parameters
Encoding Parameters
Figure 26: Encoding Module - Encoding Parameters
Module Capabilities
Comment
WMT
= WMT detected
WMA
= WMA detected
Max. Video Bit Rate
Displays the bit-rate to which you can adjust while
playing the channel. If this field displays 0, you
cannot adjust the bit-rate while playing.
Table 23: Encoder Capabilities
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Viewing and Setting Module Parameters
Encoder State
Comment
Video and Audio
FREE: Input available, a channel can be added.
STOP: Channel added and ready.
Play: Channel added and playing.
Resolutions
This table displays resolutions currently enabled or
disabled respectively. A list of resolutions can also
= Resolution enabled
= Resolution disabled
Table 24: Encoder State
Tools
Buttons
Description
Updates the displayed settings. This button is disabled if you
are logged on as Guest.
Applies changes and closes the window. This button is
disabled if you are logged on as Guest.
Closes the current window without making changes.
Opens related help topic.
Table 25: Encoding Module - Tools
Note
If Video and Audio display Running or Stop, you cannot add an additional
channel associated with the respective encoding module.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Editing the Channel Profile
Editing the Channel Profile
Each encoding module supports one WMT channel. You can
configure channels either manually or use previous
configurations that you saved as templates. MGW 2400 allows
you also to save configurations for later use.
•
•
•
•
To add a channel, refer to page 73.
To edit an existing channel, refer to page 75.
To view the channel profile and channel errors, refer to
•
•
To manage templates, refer to page 77.
To manage configurations, refer to page 79.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Editing the Channel Profile
Adding a Channel
You can manually configure a new channel or use previous
configurations that you saved as templates. You can add one
channel per installed encoding module. If you logged on as
Guest, you cannot add channels.
To define a new channel:
1. On the MGW 2400 EMS Main window, in the toolbar,
click Add Channels
; the Channel wizard
appears.
2. Assign a channel name (e.g. Test) by overwriting the
default in the Channel Name field to the upper left. Every
channel must have a different name. If you try to use a
name that has already been assigned to a different channel,
you receive an error message. A channel name can consist
of up to 256 numbers, letters and spaces.
3. Choose one of the two options listed below.
•
From Template. Choose the desired template from
the list.
•
From Type. WMT Encoding is the currently
available option.
4. Click Next
, select the desired encoding module and
add targets.
•
Encoding modules, which already have a channel
assigned, do not appear in the Modules list.
•
To add a target, choose the target type and click Add
. Each channel supports up to eight targets,
which can include one File target.
•
To remove a target, click Del
.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Editing the Channel Profile
5. To continue, click Next
appear.
; channel parameters
•
Input parameters. To view advanced video input
parameters, click Video
. For information, refer
•
Encoding (processing) parameters. To view
advanced video or audio encoding parameters, click
Video
or Audio
respectively. For
information on encoding parameters, refer to page 81.
•
Target parameters. To view or edit parameters,
select the desired target and click Edit
. For
information on target parameters, refer to page 86.
To complete adding the channel:
•
Once you have finished setting parameters, click Apply
; the Channel wizard closes and the channel appears
in the list with the new parameters set.
Note
•
•
You cannot add or remove targets for an existing channel. If you wish to
remove or add targets, you have to define a new channel.
When clicking Apply
, a window appears indicating that the
desired channel is being added. If this window does not close within 5
minutes, click Close and wait until the new channel appears in the
Channels list.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Editing the Channel Profile
Editing an existing Channel
If you logged on as Guest, you cannot edit channel parameters.
To view channel parameters without editing:
•
Select the desired channel and click View
parameters appear but are unavailable for editing.
; channel
To edit channel parameters:
1. Select the desired channel and click Edit
; channel
; the
parameters appear and are available for editing.
2. Set the desired parameters and click Apply
Channel wizard closes and the new parameters are set.
To edit video parameters while playing:
1. Select the desired channel and click Edit
; video
parameters appear.
2. Set the desired parameters and click Apply
. To
close the Video Parameters window without making
changes, click Cancel
.
Removing Channels
1. Make sure that the relevant channels are stopped.
2. Select the relevant channels and click Del
; the
selected channels are removed.
•
To remove all channels, click Select All
then Del ; all channels are removed.
and
•
Templates based on the relevant channels remain
available.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Editing the Channel Profile
Viewing the Channel Profile
In the MGW 2400 EMS Main window, click the Channels tab;
the Channels list appears displaying the current channel profile
as follows.
•
•
Channel Name. The name you assigned when you added
the channel.
Description. Displays the channel type, the slot number
and the interface where the video source is connected.
•
•
State. Displays the channel state.
Error Status. Displays the channel's status.
State
Error Status Description
Stopped
Playing
Stopped
Channel OK
Channel OK
Error
The channel is ready.
The channel is playing.
The channel encountered an error while
playing, possibly caused by unsupported
parameters that you may have set. The channel
cannot restart until this error has been resolved.
Playing
Error
Error
The channel encountered an error, but
continues playing.
Not
Ready
The channel encountered an error, possibly
caused by setting unsupported parameters.
The channel cannot start until the error has
been resolved.
Table 26: Channel State and Errors
To view a channel error:
1. Select the relevant channel.
2. Right-click the selected channel; a shortcut menu appears.
3. Choose Show Error; the relevant error message appears.
For a list of error messages and explanations, refer to
MGW 2400 EMS help.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Editing the Channel Profile
Managing Templates
To add a template, you must have at least one channel added to
the Channels list. For instructions on adding a channel, refer to
page 73.
To view existing templates:
•
On the MGW 2400 EMS toolbar, click Templates
; the Template manager appears displaying
existing templates.
To add a channel by using the Template manager:
1. On the Template manager, click Add
; the Add
Template window appears displaying existing channels.
2. Select the desired channel, assign a name and a short
description (optional) to the template and click Apply
; the channel appears in the Template manager.
Note
•
•
•
Templates can be applied to every MGW 2400 unit that you log on to.
External WMS servers that you may have configured are not saved.
Input parameters are specific to encoding modules and must therefore
be updated once you apply the relevant template to a different encoding
module.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Editing the Channel Profile
To add a template from the Channels list:
1. On the Channels list, select the desired channel and click
Save ; you will be asked to assign a name and add
a short description (optional).
2. Click Apply ; the channel is added as a template.
To delete a template:
•
On the Template manager, select the template you want to
delete and click Del
; the selected template is
deleted from the list.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Editing the Channel Profile
Managing Configurations
MGW 2400 lets you save system configurations allowing you
to restore channels and their settings from previous settings.
To view configurations:
•
On the MGW 2400 EMS Main window, in the toolbar,
click Configs ; the Device Configuration Manager
appears displaying a list of currently saved configurations.
Figure 27: The Device Configuration Manager
Note
•
•
A configuration can only be applied to the unit for which you saved it
and if no further changes have been made since it was saved.
Once you save your configuration, we strongly recommend making a
note of encoding modules, slots and the color system of connected
sources.
•
•
External WMS servers that you may have configured are not saved.
If you try to activate a configuration with encoding boards installed in
different slots or different source types connected, the configuration
cannot load and you receive an error message.
•
If you are logged on as Guest, you cannot add, remove or activate
configurations.
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Editing the Channel Profile
To activate a configuration:
•
Select the desired configuration and click Activate
; the selected configuration is activated.
To reload a configuration after restarting MGW 2400:
•
Select the desired configuration and click Auto Start
; the selected configuration reloads after restarting
MGW 2400. It may take several minutes until MGW 2400
finishes booting and loads the configuration. You cannot
log on to MGW 2400 before it does not finish loading the
configuration.
To add a configuration:
•
Click Add
, add the file name and a short
description for the desired configuration and then click OK
; the configuration is saved and appears in the
Available Device Configurations list.
To delete a configuration:
•
Select the desired configuration from the list and click Del
; the selected configuration is removed from the
Available Device Configurations list.
Note
When adding or activating a configuration, a window appears indicating that
the issued command is being processed. If this window does not close within
5 minutes, click Close and wait until the configuration has been added or
activated respectively.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Editing Channel Parameters
Editing Channel Parameters
If you add a channel, default parameters are set, which you can
change. Some video parameters may be changed while playing.
•
•
•
•
For input parameters, refer to page 67.
For encoding parameters, refer to page 81.
For adjusting parameters on the fly, refer to page 85.
For target parameters, refer to page 86.
Encoding Parameters
This section lists and explains encoding parameters.
Video Encoding Parameters
Parameters Settings
Comments
Format
WMT
WMT compliant
streams
Bit Rate (bps) QSIF, QSIF SQP: 350000 (default)
SIF, SIF SQP: 700000 (default)
64000 - 350000
150000 - 2000000
Resolution
For resolutions and supported bit-
rates, refer to page 101.
Make sure that your
receiving device and
monitor support the
resolution you
choose.
Table 27: Video Encoding Parameters
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Editing Channel Parameters
Advanced Video Encoding Parameters
•
If you are in the process of adding a channel, click Video
for advanced video encoding parameters.
•
If you are in the process of editing a channel, click
Advanced
for advanced video encoding
parameters.
•
•
To change and save advanced video encoding parameters,
click OK
To close the Advanced Encoding parameter window
.
without making changes, click Cancel
.
Parameters Settings
Comments
Fixed Bit-
Rate
Checked by default (recommended)
To enable adjusting
the bit-rate and the
Frame Sampling
Method while playing,
clear this option.
Frame
Sampling
Method
Manual
Smooth Motion
Middle
Best Quality
Full Rate
To meet certain criteria
for the frame rate,
choose the relevant
option.
You can adjust the
Frame Sampling
method while playing
when Fixed Bit-Rate is
cleared.
Frame Drop
Step
Encode every x frame
(x may range from 2 to 60)
Defines the highest
frame rate for
encoding. MGW 2400
may encode at a lower
frame rate than
Drop every x frame
(x may range from 2 to 60)
specified.
This field only shows if
you chose Manual as
Frame Sampling
Method.
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Editing Channel Parameters
Parameters Settings
Comments
Video Buffer
Window
1000 (default)
Latency related
parameter.
We recommend not
changing this parameter.
Dup Top Lines 0 - 10 (default is 0)
Sets the number of lines
'covered' on the top of
the frame to prevent the
display of artifacts.
Dup Bottom
Lines
0 - 10 (default is 1)
Sets the number of lines
'covered' from the bottom
of the frame to prevent
the display of artifacts.
DCT Filter
Automatic (default)
Disabled
Level 1
Removes details to
smooth blocking effects
at low bit-rates.
Level 2
Smooth Filter
Intra Period
Automatic (default)
Disabled
Level 1
Smoothes blocking
effects at low bit-rates.
Level 2
2 - 240
Auto (default)
Specifies the distance
between referenced I
frames in the stream. To
automatically specify the
distance, check the
checkbox next to the
Intra Period field.
Table 28: Advanced Video Encoding Parameters
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Editing Channel Parameters
Audio Parameters
Parameters
Settings
Comments
Channel Mode
Bit-rate
Mono or Stereo
Available audio bit-rates
depend on the sample rate
you chose.
Refer to page 101 for
available bit-rates and audio
modes.
Table 29: Audio Encoding Parameters
Advanced Audio Parameters
•
•
•
If you are in the process of adding a channel, click Audio
for advanced audio encoding parameters.
To change and save advanced audio parameters, click OK
.
To close the Advanced Encoding Parameter window
without making changes, click Cancel
.
Parameters
Settings
Comments
Encoding
Format
WMA
Defined by Windows WMT
Properties.
Buffer Window
1000 (default)
Latency related parameter.
We recommend not changing
this parameter.
The value for Audio must
match the one for video.
Table 30: Advanced Audio Encoding Parameters
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Editing Channel Parameters
Adjusting Video Parameters On The Fly
MGW 2400 lets you edit certain parameters while channels are
being encoded.
1. Select the desired channel and click Edit
;
parameters appear for editing.
2. Set the desired parameters and click Apply
. To
close the Video Parameters window without making
changes, click Cancel
.
For parameter settings and explanations, refer to pages 67
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Editing Channel Parameters
Target Parameters
•
•
•
For WMS Multicast, refer to the section below.
For WMS Unicast, refer to page 89.
For writing to a file, refer to page 90.
Viewing and Editing Target Parameters
•
If you are in the process of adding a channel, select the
desired target and click Edit
; a window appears
displaying the associated parameters.
•
If you are in the process of editing a channel, select the
desired target; the associated parameters appear to the right.
Parameters are unavailable for editing if the channel is
running.
WMS Multicast
Parameters
Settings
Comments
External WMS
<None> (default)
No external WMS
server is used.
IP address of an external WMS
server you may have configured for
this channel.
If you wish to use an
external WMS server,
choose the desired
server's IP address
from the list. This
WMS server must
belong to the same
VLAN and workgroup
as MGW 2400.
If you do not find the
desired server's IP
address, go to the
External WMS page in
order to add it to the
Servers list. Refer to
instructions.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Editing Channel Parameters
Parameters
Settings
Comments
Output NIC
IP address of the NIC via which
content transmits.
No external WMS
server.
Choose the MGW
2400 NIC that you use
for transmission.
External WMS
server.
Type the IP address
of the external WMS
server's NIC that you
use for transmission.
Target IP
address
Multicast IP addresses
Enter an IP address
within the listed range.
224.1.1.1 - 239.255.255.255
Make sure that the
relevant receivers are
set to the same
Multicast IP address.
Other Multicast IP
addresses are
reserved for certain
tasks or devices and
can cause network
conflicts if used for
different purposes.
Port
You may use ports between 1024
and 20000. Do not use ports
between 7008 and 7013.
Make sure you set a
unique port for each
target you add.
UDP Block Size 1024 - 20000
(default is 0 for Automatic)
We recommend
setting the UDP Block
Size value to 0 for
Automatic.
The UDP Block Size
depends on the video
and audio bit-rates.
The values set by
MGW 2400 can be
found at page 113.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Editing Channel Parameters
Parameters
Settings
Comments
NSC File Name If you write the file to a SCSI disk
connected to MGW 2400, enter the
The NSC file contains
information the player
needs in order to
full path and file name with the file
name's extension NSC, for example know how to receive
<SCSI drive>:\<Folder
names>\File.nsc.
multicast packets and
decode the multicast
stream.
If you write the file to a shared folder,
enter only the relevant PC's name
and the shared folder, for example:
You may write the
NSC file to a shared
drive on SCSI disk
connected to MGW
2400, or a network
drive or web server
that belongs to MGW
2400's workgroup and
VLAN.
\\PC\shared_folder\File.nsc
If you enter the entire path, you
receive an error message.
If saved on a web
server, the NSC file
resides in a folder
called wwwroot.
User Name
Password
User name to access the network
drive to which you write the NSC file,
if required.
Password to access the network
drive to which you write the NSC file,
if required.
Table 31: WMS Multicast Target Parameters
Note
We recommend writing NSC files to shared network drives and not to SCSI
disks.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Editing Channel Parameters
WMS Unicast
Parameters
Settings
Comments
External WMS
<None> (default)
No external WMS server
is used.
IP address of an external WMS If you wish to use an
server you may have
configured for this channel.
external WMS server,
choose the desired
server's IP address from
the list. This WMS server
must belong to the same
workgroup as MGW 2400.
If you do not find the
desired server's IP
address, go to the
External WMS page in
order to add it to the
Servers list. Refer to page
64 for instructions.
Max Clients
0 - 10 (default is 10)
Enter the max. number of
clients allowed to receive
the stream at the same
time.
UDP Block Size
1024 - 20000
We recommend setting
the UDP Block Size value
to 0 for Automatic.
(default is 0 for Automatic)
The UDP Block Size
depends on the video and
audio bit-rates. The
values set by MGW 2400
can be found at page 113.
Host URL
For example:
This field shows when the
channel is running.
mms://MGW2400/Test0
It displays the URL
required to configure the
Windows Media Player for
playing back this channel.
For further information on
playing unicast streams
and specifying the correct
URL, refer to page 93.
Table 32: WMS Unicast Target Parameters
89
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Editing Channel Parameters
File Output
Parameters
Settings
Comments
File Name
If you write the file to a SCSI disk
connected to MGW 2400, enter
the full path and file name with
the file name's extension ASF, for
example <SCSI drive>:\<Folder
names>\File.asf.
You can write the ASF
file to a local SCSI
disk connected to
MGW 2400, or a
network drive that
belongs to MGW
2400's workgroup and
VLAN.
If you write the file to a shared
folder, enter only the relevant
PC's name and the shared folder,
for example:
\\PC\shared_folder\File.asf
If you enter the entire path, you
receive an error message.
User Name
Password
Enter the user name that may be
required for the drive to which you
wish to write the file.
Enter the password that may be
required for the drive to which you
wish to write the file.
Table 33: File Output Parameters
Note
•
•
Do not transmit to more than two file targets per unit, if you write ASF
files to a SCSI disk connected to the relevant MGW 2400 unit.
If you save the NSC file to a SCSI disk connected to MGW 2400, make
sure that the relevant SCSI disk drive is shared. For instructions on
sharing a SCSI disk drive with the network, refer to page 42.
•
If you save NSC and ASF files to shared network drives, make sure that
they belong to MGW 2400's workgroup and VLAN and that they are
accessible. If the relevant network drive belongs to a PC that runs
Windows 2000 or XP, do not specify a user name and password.
•
•
We recommend verifying that shared network locations are accessible.
To do so, copy the desired path into the Run command line on the
Management PC and press Enter.
If the desired location could not be accessed, the path that you specified
is incorrect or the desired location is not accessible.
90
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Operating Channels
Operating Channels
This section instructs you on transmitting and receiving WMT
channels for playback.
To start playing a channel:
1. Log on to MGW 2400 EMS as Administrator or Super
User; the MGW 2400 EMS Main window appears with the
Modules page open. If you log on as Guest, you cannot
operate channels.
2. Click the Channels tab; the Channels page appears.
3. On the Channels page, select the desired channels and click
Play
; the selected channel starts playing. To start
all channels, click Select All
and then Play
.
To stop playing a channel:
•
On the Channels page, select the desired channel and click
Stop ; the desired channel stops playing. To stop all
channels, click Select All and then Stop
.
Note
•
•
When using an external WMS server for transmission, it may take
several minutes until the channel starts or stops playing respectively.
When starting or stopping channels, a window appears indicating that
the relevant command is being processed. If this window does not
close within 5 minutes, click Close
and wait until the relevant
channels are started or stopped respectively.
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Operating Channels
Receiving and Playing Back Streams
We recommend using Windows Media Player 9 Series (English
version). For instructions on installing Windows Media Player 9
Series, refer to page 52.
To play a multicast stream:
1. Verify that the desired channel is transmitting to a
multicast target.
2. On the Desktop of the receiving client, click
to open
Windows Media Player, the Windows Media Player screen
appears.
3. From the menu, choose Tools and then Options; the
Options screen appears. To define the correct port number,
click the Network tab and set the range of port numbers so
that your transmitting stream’s port number is included.
4. From the menu, select File and then Open, enter the
location of the NSC file and click OK, the stream starts
playing.
•
If the NSC file resides on the same LAN as Windows
Media Player, enter the network drive in the Open
URL field, for example:
\\PC\shared_folder\File.nsc.
•
•
If the NSC file resides on a web server in a folder
called wwwroot, enter the URL, for example:
To start playing, you may also browse to the NSC
file's location and drag the relevant NSC file into the
Windows Media Player window.
For further information on NSC files, refer to page 88.
92
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Operating Channels
To play a unicast stream:
1. Verify that the desired channel is transmitting to a unicast
target.
2. On the Desktop of the receiving client, click
Windows Media Player appears.
,
3. From the menu, select File and then Open URL; the Open
URL window appears.
4. Type the URL for the desired unicast stream into the Open
field in the Open URL, for example:
mms://172.16.100.44/Test0. You can use one of the
following three protocols.
•
•
mms:// Uses a UDP network connection (default).
mmst:// Uses a TCP/IP network connection and
ensures packet recovery. This protocol requires very
large CPU resources.
•
http:// Supports every network infrastructure, but
encounters staggering at high traffic.
This URL reflects the following:
•
172.16.100.44. IP address of the WMS server. If you
did not configure a WMS server, type the respective
MGW 2400 unit's IP address. You can use the
hostname instead, if your network is DNS enabled and
you added the relevant DNS server(s) under DNS
Options in the Configuration Utility.
•
•
Test. The WMT Channel's name that you assigned.
0. Target index (target number). '0' is the number for
the first target in the list and '7' for the eighth one.
The URL is displayed on the Unicast Target Parameter
page under Host URL, showing the host name instead of
the IP address.
5. Click OK; Windows Media Player starts playing the
stream.
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Upgrading MGW 2400
Upgrading MGW 2400
Upgrades will be made available for MGW 2400. The required
upgrade files are provided in zip archives available on a CD or
at Optibase's FTP site for download. Instructions for down-
loading files from Optibase's FTP site, required passwords and
information on the relevant upgrades are provided with upgrade
release notes. Details of the currently active version appear
under Current Version. The Version Management window
also indicates available disk space on drive C of MGW 2400's
disk.
Figure 28: Software Manager
To view the current software version:
•
On the MGW 2400 EMS toolbar, click SW Version
; the Version Management window appears and
displays the currently active software version's details.
Before you upgrade:
1. During the upgrade, MGW 2400's configuration returns to
the state of purchase. We advise you to make a note of the
channel profile, the network parameters and the hostname.
2. Verify that the network cables and power cords are
properly connected. Loss of power or network connection
94
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Upgrading MGW 2400
while upgrading may cause MGW 2400's disk to get
corrupted.
3. Make sure that both the relevant MGW 2400 unit and the
PC that runs MGW 2400 EMS have the same IP prefix and
subnet mask and that they belong to the same domain or
workgroup.
4. Verify that you have MGW 2400 EMS version 1.41 or
higher installed.
•
The version number appears in the Title bar of the
MGW 2400 EMS Main window.
•
If you have a previous version installed, uninstall that
version and then install the new version of MGW
2400 EMS.
5. Make sure that the network account in use on your PC is a
member of the Administrators group and has a password
assigned.
6. Disable currently active firewall software.
7. Create a folder called optibase under the root folder on a
local drive or a network drive. Make sure that this folder is
shared with full permissions and accessible to MGW 2400.
•
If C-7 appears under Version Name in MGW 2400
EMS, the Optibase folder must be a network drive.
You will have to extract the zip archive's content to
the Optibase folder.
•
•
If C-173 appears under Version Name. Copy the zip
archive to the Optibase folder without extracting its
content.
To view the version name of the current version in
use, click SW Version
; the Software Version
Manager window appears displaying the version's
details.
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 • Upgrading MGW 2400
To upgrade MGW 2400:
1. Make sure to log on to MGW 2400 EMS as Super User.
2. Verify that all channels are stopped.
3. Make a note of your current channel profile as you will
have to reconfigure the channels after upgrading.
4. In the Version Management window, click Upgrade
and follow the onscreen instructions.
•
•
If you extracted the zip file, you will be asked the user
name, the password and the domain of the PC used for
upgrading. If your PC belongs to a workgroup, leave
the Domain field empty.
Navigate to the Optibase folder. You may enter the
path into the respective field including the file name
or use the Browse button to navigate to the desired
location.
•
•
If you extracted the upgrade files, the file name should
be image.gho. If you did not extract the upgrade files,
the file name should be image.zip.
Restart MGW 2400 when you are asked to; MGW
2400 logs you off and upgrades. It may take up to 30
minutes until MGW 2400 finishes upgrading and logs
you back on. MGW 2400's configuration returns to
the state of purchase. For instructions on recon-
figuring MGW 2400, refer to page 20.
96
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Technical Specifications
Chassis
Physical
Dimensions:
17.1” (w) x 15.4” (d) x 2RU (h) (19” rack compliant, 23”
with brackets)
Weight
8kg, 15.5 Ibs)
Scalability:
Up to 6 MGE-400 or MGE-400D modules, field
swappable
Fans
Three ball-bearing fans. The fans have to be replaced
every five years.
Electrical Characteristics
Power consumption:
Max. 350W, 90-130V, 180-260V autorange
47-63 Hz
Operating line frequency:
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 • Chassis
Input/Output Interfaces
2 × 10/100 BaseT Ethernet 2 × RJ-45 (Full Duplex or Half Duplex support) -
2 × RJ-45 connectors
Ultrawide II SCSI - 68 pin SCSI connector
RS-232 serial port – RS-232 (D-9) connector
Environmental
Operating temperature
Storage temperature
5 to 45°C, 41-113°F
-10-70°C, 14-158°F
Safety Standards
CE-LVD
98
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 • Chassis
Management
SNMP MIB
EMS based remote management application.
Telnet and FTP client for remote configuration, diagnostics and software
upgrades.
Local configuration via RS-232 port.
Network Protocols
UDP Unicast and Multicast
TCP/IP
HTTP
SNMP
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 • Encoding Modules
Encoding Modules
MGE-400 and MGE-400D – WMT, ASF compliant
Physical Dimensions
185 x 100mm, 7.2 x 3.9”
Standard Compliance
Microsoft Windows Media Technology, ASF compliant
Input Signals
Video Inputs
Audio Inputs
NTSC & PAL
Composite Video (BNC)
S-Video (MiniDin)
SDI (BNC), supported for MGE-400D only)
Unbalanced Analog Stereo Line Input (MiniJack)
Input Impedance: 47 kΏ
Digital AES/EBU (RCA JACK))
Input impedance: 110 Ώ
Max. Input Audio Power < 0 db
Sampling Frequency: 32, 44.1 and 48 kHz at 20 bits
per sample.
Encoding Format
File Format
WMT ASF
MPEG-4
Video Format
Audio Format
Audio Mode
MS Audio
Mono, Stereo
100
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 • Encoding Modules
Video Resolutions and Bit-Rates
NTSC
PAL
Bit-Rates (bps)
176x112
160x112
352x240
320x240
176x144
192x144
352x288
384x288
QSIF
64000 - 350000
QSIF SQP
SIF
64000 - 350000
150000 - 2000000
150000 - 2000000
SIF SQP
Audio Modes and Bit-Rates
Sampling Rate 32 kHz
Audio Bit-Rate
Supported Audio Mode
20016
22008
32000
32032
36016
40000
44024
48008
64000
64024
Mono
Stereo
Mono
Mono, Stereo
Stereo
Stereo
Stereo
Stereo
Stereo
Stereo
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 • Encoding Modules
Sampling Rate 44.1 kHz
Audio Bit-Rate
Supported Audio Mode
32040
48016
64040
64080
80016
96040
128040
160032
Mono
Stereo
Stereo
Stereo
Stereo
Stereo
Stereo
Stereo
Sampling Rate 48 kHz
Audio Bit-Rate
Supported Audio Mode
128008
160000
Stereo
Stereo
102
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 • System Defaults
System Defaults
DHCP Client
Hostname
Enabled for NIC A
Disabled for NIC B
MGW2400
My System Settings
We recommend to make a note of customized settings, as you
may need them for future reference.
Hostname
DNS IP Addresses
DNS 1
DNS 2
DNS 3
DNS 4
DNS 5
NIC A
IP Address
Subnet mask
Default Gateway
WINS
Network Mode of Operation
NIC B
IP Address
Subnet mask
Default Gateway
WINS
Network Mode of Operation
103
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 • User Names and Passwords
User Names and Passwords
We recommend that make a note of additional users and
passwords that you defined, as you may need them for future
reference.
MGW 2400 EMS Users
Default Users
User Profile
Password
super
admin
guest
Super User
Administrator
Guest
optibase
optibase
optibase
New Users
User Profile
Passwords
MGW 2400 Administrator
User Name
Default Password
New Password
Administrator
Administrator
104
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5
Troubleshooting
Hardware Errors
The Problem Possible Cause
Possible Solution
MGW 2400
won’t turn on.
•
No power supply
to the MGW
2400.
•
Restore power supply to
MGW 2400.
MGW 2400
turns on, but
won’t boot.
•
MGW 2400 may
have
encountered a
temporary error
causing it not to
boot.
•
Switch MGW 2400 off and on
again.
•
•
If the above does not help,
turn MGW 2400 off, remove
all encoding modules and turn
on again. Wait until MGW
2400 finished booting and the
Power LED turns green.
Switch MGW 2400 off, re-
install the encoding modules
and switch on again.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 • Troubleshooting
The Problem Possible Cause
Possible Solution
I cannot
•
•
•
Is your serial
cable properly
connected?
•
•
•
Check the connection of the
serial cable. Connect properly
or replace the cable.
connect to
MGW 2400 via
RS-232.
You are not
connected to the
correct local
COM port.
Connect MGW 2400 to the
Configuration PC’s COM1
port.
Your COM port is
not correctly
configured.
Open HyperTerminal’s COM
Properties screen, choose
COM1 and configure as
follows:
Bits per second: 115000
Data Bits:
Parity:
8
None
Stop bits:
Flow Control:
1
None or
Hardware
•
•
You connected
both NICs to the
same network
segment.
•
•
Switch MGW 2400 off and
connect both NICs to
separate network segments.
A network device
with MGW 2400's
hostname
Switch MGW 2400 off and
change the hostnames of the
relevant devices. We
already exists in
at least one of
the network
recommend changing MGW
2400's hostname once you
switched MGW 2400 back on.
Refer to page 25 for
segments.
instructions on changing
MGW 2400's hostname.
•
•
Your PC’s COM
port may not be
working.
•
•
Have your computer’s COM
port replaced.
MGW 2400’s RS-
232 port may not
be working.
Call for technical support.
106
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 • Troubleshooting
The Problem Possible Cause
Possible Solution
I connected a
SCSI hard
disk to MGW,
but MGW
•
You may have
chosen a
forbidden SCSI
address.
•
Check the SCSI address.
Note that ‘7’ is reserved for
the SCSI controller inside
MGW 2400.
2400 won’t
boot.
I can’t encode
a stream, the
Source LED is
off and the
•
Bad source or no
source connected
•
Connect the source properly.
Channel LED
is green.
The Channel
LED is red
•
•
Channel error
Software error
•
•
Restart encoding using
different parameters. If this
does not help, refer to the
Error Message list in the
MGW 2400 EMS help file.
The Channel
LED blinks
red
If this error persists, call for
technical support.
107
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 • Troubleshooting
Errors while running MGW 2400 EMS
The Problem Possible Cause
Possible Solution
I cannot install
the MGW 2400
EMS
•
I have less than
200 MB free hard
disk space.
•
Free up space, as you need
at least 200 MB to ensure
seamless installation.
I cannot log
on to MGW
2400
•
The relevant unit
is switched off,
disconnected or
not reachable
•
Verify that the desired units
are running and properly
connected and configured.
Refer to page 28 for
instructions on configuring
MGW 2400.
•
•
The
•
•
On the Management PC, go
to the Add/Remove Hardware
and disable all NICs except
one.
Management PC
has more than
one NIC
installed.
I try locating
MGW 2400
units on the
network by
using
Discover, but
no units are
found.
The relevant
units are not
connected, not
reachable or
switched off.
Verify that the desired units
are running and properly
connected and configured.
Refer to page 28 for
instructions on reconfiguring
MGW 2400.
•
The relevant
units may belong
to a different
workgroup and/or
VLAN.
•
Only units that belong to the
Management PC's workgroup
and VLAN can be located. If
you wish to use Discover, the
Management PC and all
relevant MGW 2400 units
must belong to the same
workgroup and VLAN.
108
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 • Troubleshooting
The Problem Possible Cause
Possible Solution
The channels
became un-
available after
unsuccessfull
y trying to
•
Channel error
•
•
Remove the relevant channel
and add a new one as
If you cannot remove the
channel or this error recurs,
restart MGW 2400.
start and stop
several times.
MGW 2400
EMS freezes
repetitively
after about
one minute.
•
MGW 2400 EMS
may not
communicate
properly with
MGW 2400.
•
Use the Task Manager to
close MGW 2400 EMS. To
close the Java Runtime
Environment, click the
Processes tab and close
java.exe.
•
•
Make sure that both NICs are
connected to two separate
network segments.
•
•
The relevant PC
has more than
one NIC
Make sure that the PC on
which you installed the MGW
2400 EMS, has only one NIC
enabled, otherwise the MGW
2400 EMS cannot
installed.
communicate with MGW
2400.
The response
time may be too
long.
•
Connect MGW 2400's NIC
used for MGW 2400 EMS and
the Management PC to the
same workgroup and VLAN.
109
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 • Troubleshooting
The Problem Possible Cause
Possible Solution
I cannot start
a multicast
stream.
•
The required
NSC file may not
be reachable
•
Make sure that the desired
NSC file's location belongs to
MGW 2400's workgroup and
VLAN. An error message may
appear in this case. For
instructions, refer to page 88.
The external
WMS server
cannot be
reached
•
•
The WMS server
may be offline or
not reachable.
•
•
Make sure that the relevant
WMS server is properly
configured and resides in
MGW 2400's workgroup and
VLAN.
I cannot write
to a file (*.asf
file output).
The location you
specified cannot
be reached or the
response time is
too long.
Make sure that you choose a
drive in a location that
belongs to MGW 2400's
workgroup and VLAN. For
instructions, refer to page 90.
Error Messages
Error messages with explanations and workarounds can be
found in the MGW 2400 EMS help system.
110
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
Optimizing Performance
If not otherwise noted, all supported video/audio bit-rate
combinations perform smoothly for up to six channels serving
the desired number of multicast and unicast targets.
Stereo at a Sample Rate of 32 kHz
At audio bit-rates of 64000 - 64024 bps, six channels can
transmit to three unicast targets.
At audio bit-rates of 48008 - 22008 bps, five channels can
transmit to three unicast targets.
Stereo at a Sample Rate of 44.1 kHz
Each channel may serve up to three unicast targets. In most
cases, up to six channels can transmit at a time.
Up to five channels can transmit at video bit-rates of 1750000
and 2000000 bps if the audio bit-rates are set to 48016, 128040
or 160032 bps.
Stereo at a Sample Rate of 48 kHz
Up to four channels can transmit at video bit-rates above
500000 bps and available audio bit rates of your choice.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B
UDP Block Size Values
UDP Block Size values strongly depend on video and audio bit-
rates.
This section shows UDP Block Size values selected
automatically when choosing 0 for Automatic on the MGW
2400 EMS Target page. This section also shows you the lowest
values that you may choose manually.
Mono
Audio Sampling Rate: 32 kHz:
Video
Bit-Rates (bps)
Audio
Bit-Rates (bps)
Default UDP
Block Size
Lowest UDP
Block Size
200000
200000
200000
300000
300000
300000
500000
500000
500000
700000
700000
20016
32000
32032
20016
32000
32032
20016
32000
32032
20016
32000
2881
3031
3031
4131
4281
4274
6631
6781
6781
9131
9281
949
340
914
944
339
910
940
337
906
938
337
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B • UDP Block Size Values
Video
Bit-Rates (bps)
Audio
Bit-Rates (bps)
Default UDP
Block Size
Lowest UDP
Block Size
700000
32032
20016
32000
32032
20016
32000
32032
20016
32000
32032
9281
904
937
337
903
936
336
902
935
336
901
1000000
1000000
1000000
1500000
1500000
1500000
2000000
2000000
2000000
12881
13031
13031
16122
16122
16122
16112
16112
16112
Audio Sampling Rate: 44.1 kHz:
Video
Bit-Rates (bps)
Audio
Bit-Rates (bps)
Default UDP
Block Size
Lowest UDP
Block Size
200000
300000
500000
700000
1000000
1500000
2000000
32040
32040
32040
32040
160032
160032
160032
3031
837
833
829
828
826
825
825
4281
6781
9281
13031
16122
16112
114
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B • UDP Block Size Values
Stereo
Audio Sampling Rate: 32 kHz:
Video
Bit-Rates (bps)
Audio
Bit-Rates (bps)
Default UDP
Block Size
Lowest UDP
Block Size
200000
200000
200000
200000
200000
200000
200000
200000
300000
300000
300000
300000
300000
300000
300000
300000
500000
500000
500000
500000
500000
500000
500000
500000
700000
22008
32032
36016
40000
44024
48008
64000
64024
22008
32032
36016
40000
44024
48008
64000
64024
22008
32032
36016
40000
44024
48008
64000
64024
22008
2906
3031
3081
3131
3138
3231
3431
3430
4156
4281
4331
4374
4431
4481
4681
4681
6656
6781
6831
6881
6931
6981
7181
7181
9156
1036
914
1017
1121
1225
1329
599
1744
1030
910
1013
1116
1220
1323
597
1737
1029
906
1009
1111
1215
1318
595
1730
1024
115
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B • UDP Block Size Values
Video
Bit-Rates (bps)
Audio
Bit-Rates (bps)
Default UDP
Block Size
Lowest UDP
Block Size
700000
32032
36016
40000
44024
48008
64000
64024
22008
32032
36016
40000
44024
48008
64000
64024
22008
32032
36016
40000
44024
48008
64000
64024
22008
32032
36016
40000
44024
48008
64000
9281
904
700000
9331
1007
1109
1213
1315
594
700000
9381
700000
9431
700000
9481
700000
9681
700000
9681
1727
1022
903
1000000
1000000
1000000
1000000
1000000
1000000
1000000
1000000
1500000
1500000
1500000
1500000
1500000
1500000
1500000
1500000
2000000
2000000
2000000
2000000
2000000
2000000
2000000
12906
13031
13081
13131
13181
13231
13431
13431
16122
16122
16122
16122
16122
16122
16121
16121
16112
16112
16112
16111
16111
16111
16111
1005
1108
1211
1313
593
1725
1021
902
1004
1106
1209
1312
593
1723
1020
901
1003
1106
1209
1311
593
116
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B • UDP Block Size Values
Video
Bit-Rates (bps)
Audio
Bit-Rates (bps)
Default UDP
Block Size
Lowest UDP
Block Size
2000000
64024
16111
1722
117
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B • UDP Block Size Values
Audio Sampling Rate: 44.1 kHz:
Video
Bit-Rates (bps)
Audio
Bit-Rates (bps)
Default UDP
Block Size
Lowest UDP
Block Size
200000
200000
200000
200000
200000
200000
200000
300000
300000
300000
300000
300000
300000
300000
500000
500000
500000
500000
500000
500000
500000
700000
700000
700000
700000
700000
700000
48016
64040
64080
80016
96040
128040
160032
48016
64040
64080
80016
96040
128040
160032
48016
64040
64080
80016
96040
128040
160032
48016
64040
64080
80016
96040
128040
3231
3431
3432
3631
3831
4231
4631
4481
4681
4682
4881
5081
5481
5881
6981
7181
7182
7381
7581
7981
8381
9481
9681
9682
9881
10081
10481
1213
1589
457
1965
2340
3089
3838
1208
1583
456
1957
2332
3081
3828
1230
1577
454
1951
2325
3072
3818
1201
1574
453
1947
2321
3067
118
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B • UDP Block Size Values
Video
Bit-Rates (bps)
Audio
Bit-Rates (bps)
Default UDP
Block Size
Lowest UDP
Block Size
700000
160032
48016
64040
64080
80016
96040
128040
160032
48016
64040
64080
80016
96040
128040
160032
48016
64040
64080
80016
96040
128040
160032
10881
13231
13431
13432
13631
13831
14231
14631
16122
16122
16120
16120
16120
16120
16120
13231
13431
13431
13631
13831
14231
14631
3813
1199
1572
453
1000000
1000000
1000000
1000000
1000000
1000000
1000000
1500000
1500000
1500000
1500000
1500000
1500000
1500000
2000000
2000000
2000000
2000000
2000000
2000000
2000000
1945
2318
3063
3809
1197
1570
452
1942
2315
3060
3805
1197
1569
452
1941
2314
3058
3808
119
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B • UDP Block Size Values
Audio Sampling Rate: 48 kHz:
Video
Bit-Rates (bps)
Audio
Bit-Rates (bps)
Default UDP
Block Size
Lowest UDP
Block Size
200000
200000
300000
300000
500000
500000
700000
700000
1000000
1000000
1500000
1500000
2000000
2000000
128008
160000
128008
160000
128008
160000
128008
160000
128008
160000
128008
160000
128008
160000
4231
3239
4025
3230
4015
3221
4005
3216
3999
3212
3994
3208
3990
3206
3988
4631
5481
5881
7981
8381
10481
10881
14231
14631
15892
16119
16110
16110
120
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C
Optimizing your Network
Introduction
In order for rich media to be an effective tool for your business
you must first provision your network to support streaming.
Below are some rules of thumb to ensure that video streaming
will enhance your company’s performance without hurting your
network performance.
Switches are always better than Hubs
Hubs contain only one collision plane, rendering hub-based
networks unproductive because of their inadequacy in handling
collisions. A collision is an Ethernet event that occurs when two
Ethernet frames collide. Switches, on the other hand, are
comprised of ports. Each port is a separate collision plane.
Thus, only those machines connected to the same port share a
collision plane, reducing the number of collisions and
increasing available resources. Moreover, Level III enabled
switches support IP multicasting using IGMP (Internet Group
Management Protocol) across LAN and VLAN spaces without
interfering with the productivity of the rest of the users
connected to the network.
Whenever possible, separate Departments
This is especially important in large organizations. If your
network is segmented well and each segment is connected to a
common backbone, maximum utilization on one segment will
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C • Optimizing your Network
not adversely affect other segments. In this case, clusters of
people will have access to resources from the same common
device that connects them to the backbone.
Exploit new Technologies for your Backbone
Your backbone should be larger than the pipes that connect to
it. If your network is entirely 100BaseT, a 100BaseT connection
is probably not going to be big enough for the backbone. Use of
ATM or Gigabit Ethernet will help you solve bottleneck
problems along the company backbone.
Use protocol shaping and Protocol Shapers
Protocol shaping is becoming more and more popular as a way
of controlling bandwidth use within organizations. Protocol
shapers are hardware devices that allocate network resources
according to specific protocols.
122
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C • Optimizing your Network
Network Configurations that are friendly to
Streaming
100BaseT Switched Networks
More bandwidth is always better than less bandwidth.
100BaseT appliances have more features and more capabilities
than 10BaseT appliances. While it is true that a 10BaseT
network can theoretically support the streaming of an MPEG-1
SIF stream at 1-1.2 Mbps, this will effectively use 30% to 40%
of available bandwidth, rendering the network ineffective.
In 100BaseT networks, each client occupies its own collision
plane, allowing it to take full advantage of the bandwidth
available. Many 100BaseT switches and network cards have
added features including the ability to "talk" to the network in
full duplex mode, allowing them to send and receive data at the
same time. Many 100BaseT switches also support some Level
III capabilities, including the ability to manage IGMP groups.
100BaseT Hub and Switched Networks
100BaseT Hub and switched networks can also be used for
streaming. This hybrid network can support streaming if it is
not over utilized and deploys 100BaseT hubs. This type of
network can contain "dead spots" - areas that cannot receive the
stream or receive it poorly. Dead spots need to be dealt with by
altering some of the network connections or by replacing the
errant Hub with a switch.
ATM
ATM can be implemented either as a backbone solution or as an
entire network solution. In the backbone scenario, ATM is used
to connect departments, floors, or any part of the organization
that is distant from the main server center. In the network
scenario, ATM is used as the entire LAN, WAN or MAN
123
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C • Optimizing your Network
(Metropolitan Area Network). LAN Emulation (LANE) is used
in these types of networks to give an Ethernet feel to the
network. This emulation is easier to implement than IP
emulation over ATM and is much more popular. ATM’s broad
bandwidth (155Mb) and interfaces, with no collisions, is ideal
for streaming.
124
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D
Glossary of Terms
Access time – The time between issuing a command to read or
write a specific location until reading or writing actually starts
at that location (in mass storage devices).
Algorithm – A detailed description of a method.
Amplifier – A network component, also known as a Repeater.
Amplifiers increase the power of a signal when it is lost due to
attenuation. They allow signals to cover greater distances in a
LAN environment.
Analog Video – Information representing images is in a
continuous-scale electrical signal for both amplitude and time.
Application Layer – The seventh layer in the OSI model. The
Application layer defines program-to-program communication,
or how applications access network services. Services defined
by the Application layer include file transfer, job transfer and
terminal emulation.
Artifacts – A blurred or blocky part of the image in a digital
video stream.
Aspect Ratio – The width/height ratio of a television set or
movie screen. Most television sets have a 4:3 aspect ratio. Wide
screen television sets have a 16:9 aspect ratio. When a movie is
transferred to video, many producers crop the sides of the
picture so that it fits the 4:3 aspect ratio of most television sets.
Another method is to put the video in a "letter box". This
method shrinks the picture until it is small enough to fit into a
4:3 aspect ratio TV set.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D • Glossary of Terms
The letterbox method produces a black band at the top and
bottom of the screen, wasting the television's vertical resolution.
AVI – Refers to Audio Video Interleaved, the original term for
Microsoft’s Video For Windows.
Bandwidth – The amount of data being able to transmit during
a defined period of time. For digital devices, the bandwidth is
usually expressed in bits per second or bytes per second. For
analog devices, the bandwidth is expressed in cycles per second
or Hertz (Hz).
B Frames – Bi-directional frames; one of the three picture types
in MPEG compression. B frames are coded in relation to
previous or subsequent I or P frames. B frames do not serve as a
reference for other frames.
Bit Stream – A serial sequence of bits.
Bitmap – An image made up of pixels on the screen, stored as a
collection of bits. A bitmap file usually carries the extension
BMP.
Bits per Pixel – The number of bits used to represent the color
value of each pixel in a digitized image. The color value of
pixels can be 8, 16 or 24 bits. When the color value of a pixel is
24 bits there are 16.6 million colors in an image.
Bridge – A network component connecting two LANs, thus
extending the range of the network. Bridges check data and
forward them across LANs.
Brightness – The brightness of a picture describes how much
light appears to be emitted from it.
Broadcast – Transmitting data simultaneously to several or all
stations within a network.
Brouter – A network component that serves as both a Bridge
and a Router.
Buffer – Space being allocated on a system’s Random Access
Memory (RAM) where data are temporarily stored until being
transferred to another part of the system. In streaming
126
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D • Glossary of Terms
applications, buffers store video or audio data until there is
enough information for the stream to be composed.
Bus Topology – A LAN network in which all nodes connect to
the same cable. Data transmit across this one cable.
CBR – Refers to Constant Bit-Rate and stands for the bit-rate of
a data stream remaining constant during compression
throughout the entire encoding process. This parameter may
also be referred to as Fixed Bit-Rate.
CCIR-601 – A standard (now known as ITU-R 601) that
defines the encoding parameters of digital television for studios.
ITU-R 601 refers to color difference (Y,R-Y, B-Y) and RGB
video. It defines sampling systems, RGB/Y, R-Y and B-Y
matrix values and filter characteristics. ITU-R 601 usually
refers to color difference component digital video (as opposed
to RGB) for which it defines 4:2:2 sampling at 13.5 MHz with
720 luminance samples per active line and 8 or 10-bit
digitizing.
Clip – A segment of a video or an entire video being considered
one unit based on content.
Coaxial Cable – Cable consisting of a central copper wire
being surrounded with insulation and a grounded shield of
braided wire. Coaxial cables are widely used in the cable
television and computer industries. It is less prone to
interference than regular wire cables.
CODEC – Acronym for encoder and decoder.
Connectionless vs. Connection-oriented Protocols – When
using a connectionless protocol, hosts are sending data without
establishing a connection with the recipient. The host does not
know whether the data arrive at their destination.
Connection-oriented protocols require a designated path to be
established between the sender and receiver.
Coding – The process of representing a varying function as a
series of digital numbers.
127
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D • Glossary of Terms
Color Noise – Random interference in the color portion of a
composite video system. Because of reduced color bandwidth
or color subsampling, color noise appears as relatively long
streaks of incorrect color in the image.
Collision – A collision is an Ethernet event occurring when two
Ethernet frames collide. This may happen since every host can
transmit the moment it has something to transmit. Therefore
two hosts may transmit at the same time causing a collision.
Collision Plane – A collision plane is a bus or a wire where
collisions can take place in networks.
Composite Video – A color video signal that contains all of the
color information in one signal. Typical composite television
standard signals are NTSC, PAL, and SECAM.
Compression – A digital process that allows data to be stored
or transmitted using less than the normal number of bits. Video
compression techniques reduce the number of bits required to
store or transmit images.
Contrast – The contrast of a picture describes the difference
between light and dark. In a picture with high contrast the
transition from dark to light is very clear.
D1 – A format for recording digital video based on the ITU-R
601 standard. The term is also used to describe the resolution of
a digital video stream in comparison to the CCIR-601
resolution, for example D1 or Half D1.
Datalink Layer – Layer II in OSI Systems, This layer assures
the flow of information in the network.
Data Rate – The speed of a data transfer process, normally\
expressed in bits per second or bytes per second (e.g. the data
rate of CD-ROM is 1.2 Mbps).
Data Transfer Rate – The transfer rate of the storage media
itself. For example, the maximum data transfer rate of a CD-
ROM is 1.2 MB.
Default Gateway – The Default Gateway is a routing device
that receives all packets being sent to destination addresses
128
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D • Glossary of Terms
outside the subnet and serves as connection between the current
subnet and the outside world.
DHCP – Refers to the Dynamic Host Configuration Protocol
used by a host to obtain all necessary configuration information
including IP addresses.
DLL – Dynamic Linked Library, a development tool.
DNS – ‘Domain Name System’, the online distributed database
system being used to map human-readable machine names into
IP addresses. DNS servers throughout the Internet implement a
hierarchical namespace allowing sites the freedom in assigning
machine names and addresses. DNS also supports separate
mappings between mail destinations and IP addresses.
Domain – In general, a domain is an area of control or a sphere
of knowledge. In computing and telecommunication in general,
a domain is a sphere of knowledge identified by a name.
Typically, the knowledge is a collection of facts about some
program entities or a number of network points or addresses.
On the Internet, a domain consists of a set of network addresses.
This domain is organized in levels. The top level identifies
geographic or purpose commonality (for example, the nation
that the domain covers or a category such as "commercial").
The second level identifies a unique place within the top level
domain and is, in fact, equivalent to a unique address on the
Internet (an IP address). Lower levels of domain may also be
used.
Strictly speaking, in the Internet's domain name system (DNS),
a domain is a name with which name server records are
associated that describe subdomains or host. For example,
"optibase.com" could be a domain with records for
"www.optibase.com" and "www1.optibase.com," and so forth.
In Windows NT and Windows 2000, a domain is a set of
network resources (applications, printers, and so forth) for a
group of users. The user only needs to log on to the domain to
gain access to the resources, which may be located on a number
of different servers in the network.
129
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D • Glossary of Terms
Driver – A software entity that provides a software interface to
a specific piece of hardware. For example, the MPEG-5000
video driver provides software access to the video board
hardware.
DSL – Refers to the Digital Subscriber Line, a technology for
bringing high-bandwidth information to homes and small
businesses over ordinary copper telephone lines. xDSL refers to
different variations of DSL, such as ADSL, HDSL, and
RADSL. Assuming your home or small business is close
enough to a telephone company central office that offers DSL
service, you may be able to receive data at rates up to 6.1
megabits (millions of bits) per second (of a theoretical 8.448
megabits per second), enabling continuous transmission of
motion video, audio, and even 3-D effects. More typically,
individual connections will provide from 1.544 Mbps to 512
Kbps downstream and about 128 Kbps upstream. A DSL line
can carry both data and voice signals and the data part of the
line is continuously connected. DSL installations began in 1998
and will continue at a greatly increased pace through the next
decade in a number of communities in the U.S. and elsewhere.
Compaq, Intel, and Microsoft working with telephone
companies have developed a standard and easier-to-install form
of ADSL called G.Lite that is accelerating deployment. DSL is
expected to replace ISDN in many areas and to compete with
the cable modem in bringing multimedia and 3-D to homes and
small businesses.
EISA – Refers to a full 32-bit bus developed in 1989 to offer
support for existing ISA expansion boards and to provide a
platform for future growth. The EISA bus can accommodate
more pins than an ISA bus. An EISA connector has a two-tier
slot design accepting both ISA and EISA cards.
Encode – Refers to compressing.
Field – Refers to individual pictures inside a video stream. One-
half of a frame is composed of odd (even) lines of video. These
lines comprise the odd (even) field.
Fixed Bit-Rate - Refer to CBR (Constant Bit-Rate).
130
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D • Glossary of Terms
Frame – Refers to a single picture being part of a series. When
the series is viewed at speed, a “moving picture” is created.
Frame rate – The frame rate of a video sequence refers to how
many frames are viewed per second.
Frame Sampling – Customizable frame rate
FTP – Refers to the File Transfer Protocol, a high-level
protocol for transferring files from one device or PC to another.
FTP uses TCP.
Full Motion Video – Video reproduction at 30 frames per
second for NTSC-original signals or 25 frames per second for
PAL-original signals.
Gateway – The term IP Gateway was originally used for
dedicated computers routing packages. Gateway refers now to
an application program that connects two services.
GOP – Refers to the Group Of Pictures, a single MPEG video
random-access unit.
Green Book – The formal standards document for CD-i.
Hub – An electronic device in a network to which multiple
computers connect by usually using twisted pair wiring. A hub
simulates a network that interconnects the attached computers.
The Hub Technology is popular for Ethernets.
Host – Any end-user computer system that connects to a
network. Hosts range in size from PCs to mainframe computers.
HTML – Refers to the Hypertext Markup Language, the format
used in Web-based material.
Hue – The hue of a color describes whether a color is basically
red, orange, yellow, green, etc.
HSI – Refers to Hue Saturation Intensity, a tri-stimulus color
system being based on the parameters of hue, saturation, and
intensity (luminance). It is sometimes also referred to as HSV
(Hue-Saturation-Value).
IEC – Refers to the International Electro technical
Commission, a governing body working with the ISO.
131
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D • Glossary of Terms
I Frames – Intra Frames, which are key reference frames in the
MPEG compression algorithm. I-frames contain all the data
needed to represent an entire frame,
IGMP – Refers to the Internet Group Management Protocol, an
Internet protocol that provides a way for an Internet computer to
report its multicast group membership to adjacent routers.
Multicasting allows one host computer on the Internet to send
content to multiple other computers having identified
themselves as being interested in receiving the transmitting
computer's content. These networks enable streaming to an
audience being "tuned in" by setting up a multicast group
membership without interfering with those users not being
tuned in.
Image – A still picture or one frame of a motion sequence.
Interleave – An arrangement of audio and video data inside the
file.
Interpolation – Scaling the image from a smaller size to a
larger size while intelligently creating new pixels.
ISO – Refers to the International Standards Organization, the
governing body that creates standards.
IP– Refers to the Internet Protocol used along with the
Transport Control Protocol (TCP) to send data divided into data
packets over the Internet. While TCP keeps track of the
individual data packets, IP handles the actual delivery of the
data.
Jitter – This is the difference of the latencies between two data
packets and can cause real-time data packets to arrive out of
order.
JPEG (Joint Photographic Expert Group) – An ISO
committee formed to develop the standard for the compression
of still images.
Kbps – Kilobits per second. A data flow rate indicating exactly
103 bits per second.
132
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D • Glossary of Terms
KBps – Kilobytes per second. A date flow rate indicating
exactly 210 bytes per second.
Kiosk – A stand-alone unit being used for delivering
information.
Laser Disc – An analog storage device that can read video and
sound.
Latency – The minimum time required to move data from one
point to another. Once latency is present, it cannot be
optimized. The cause has to be removed (as in using an internal
device rather than an external one to remove the latency caused
by the serial port). To maximize throughput, use the highest
bandwidth available.
LAN – Refers to local area networks (e.g. within a business),
which is a group of PCs and network devices dispersed over a
relatively limited area and connected by a communications link
that allows one device to interconnect with any other on the
network.
LED – Control unit that indicates function or malfunction.
Level – The signal amplitude in video.
Linear PCM – A non-compressed digital audio format. The
DVD specification allows for 16 to 24-bit Linear PCM audio
sampled at 48 or 96 kHz.
Luminance – A component, the black and white or brightness
element of an image.
Macro block – 16 x 16 pixel squares being used in the MPEG
compression scheme.
Mbps – Megabits per second. A data flow rate indicating
exactly 106 bits per second (bps).
MBps – Megabytes per second. A date flow rate indicating
exactly 220 bytes per second (Bps).
MJPEG or Motion JPEG – A deviation from the JPEG
specification where still image compression is used to compress
motion video.
133
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D • Glossary of Terms
Motion Compensation – A video compression technique that
makes use of the redundancy between adjacent frames of
motion video.
Motion Video – Refers to video that displays real motion. It is
accomplished by displaying a sequence of image (frames)
rapidly enough that the eye sees the image as a continuously
moving picture.
MPEG – Refers to the Moving Pictures Expert Group, a branch
of the ISO - IEC Joint Technical Committee 1, which is
working on algorithm standardization for the compression of
Motion video.
Multiplexing – Combining two or more data streams together
into a single stream.
Networking Layer – Layer III in OSI Systems, navigates
information, which is being transmitted over the network.
NIC – Network Interface card
NTSC – Refers to the National Television Standards
Committee and is the United States' standard for scanning TV
signals and has been adopted by numerous other countries.
Frames are displayed at a rate of 30 frames per second. NTSC is
based on a 525/60-line/field system. The bandwidth for the
NTSC luminance signal is 4.2 MHz. The bandwidths for the I-
and Q-channels are 1.3 and 0.4 MHz respectively. Other
standards are PAL and SECAM.
OLE – Refers to Object Linking and Embedding, a Microsoft
protocol to link applications.
OSI – Refers to Acronym for National Television Systems
Committee, an ISO standard for worldwide communications
defining a framework to implement protocols in seven layers.
Control is passed from one layer to the next, starting at the
application layer in one station, proceeding to the bottom layer,
over the channel to the next station and back up the hierarchy.
PAL – Refers to Phase Alternation Line and is Europe's and
most of the world's standard of scanning TV signals. Frames are
134
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D • Glossary of Terms
displayed at a rate of 25 frames per second. PAL is based on a
625/50-line/field system. The bandwidth for PAL is 5.5 MHz
for luminance and 1.3 MHZ for U and V. Other standards are
NTSC and SECAM.
PCI – Refers to Peripheral; Component Interconnect, a high-
speed-system bus specification that provides 32 or 64-bit data
paths at 33 or 66MHz clock rates.
Pixel – Refers to a single element of an image.
Post-filtering – Processing pictures after compressing, i.e.
scaling to size and smoothing edges.
Pre-filtering – Processing pictures before compressing, i.e.
scaling to size and smoothing edges.
P Frame – Predicted frame; used in MPEG compression, which
are coded with respect to the nearest previous I or P frames. P
frames serve as a prediction reference for B-Frames and future
P frames.
Processing – Refer to Encoding.
QSIF – Refers to Quarter Standard Interface Format. The
computer industry, which uses square pixels, has defined QSIF
to be 160 × 120 active pixels, with a refresh rate of whatever the
system is capable of supporting.
Red Book – Formal standards document for CD Digital Audio.
RS-232 – A standard defined by EIA specifying the electrical
characteristics of slow-speed interconnections between
terminals and computers or between two computers. Although
the standard commonly used is RS-232C, most people refer to it
as RS-232.
Saturation – Defines the intensity of color. A color with a high
saturation appears very strong. A color with low saturation
appears washed-out. Zero saturation is white (no color), and
maximum saturation is the deepest color possible.
135
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D • Glossary of Terms
SCSI (Small Computer System Interface) – Interface that
allows up to 7 or 15 devices to be connected to a single SCSI
port in series (daisy-chain).
SDI – Refers to Serial Digital Interface, the standard based on a
270 Mbps transfer rate. This is a 10-bit, scrambled, polarity
independent interface, with common scrambling for both
component ITU-R 601 and composite digital video and four
channels of (embedded) digital audio. Most new broadcast
digital equipment includes SDI, which greatly simplifies its
installation and signal distribution. It uses the standard 75 ohm
BNC connector and coax cable as is commonly used for analog
video, and can transmit the signal over 600 feet (200 meters)
depending on cable type.
SECAM – Refers to Sequential Color Avec Memoire, an
acronym for a color TV system developed in France and used in
the former USSR. SECAM operates with 625 lines per picture
frame and 50 cycles per second. It is incompatible with PAL
and NTSC.
Seek time – The time required to position the Reading head
above the track containing the requested data.
Server – A server is a computer program that provides services
to other computer programs in the same or other computers.
The computer that runs a server program is itself frequently
referred to as a server (though it may contain a number of server
and client programs).
In the client/server programming model, a server is a program
that awaits and fulfills requests from client programs in the
same or other computers. A given application in a computer
may function as a client with requests for services from other
programs and a server of requests from other programs.
SIF – Refers to Standard (or Source) Input Format. This video
format was developed to allow the storage and transmission of
digital video. The 625/50 SIF format has a resolution of 352 x
288 active pixels and a refresh rate of 25 frames per second.
The 525/60 SIF format has a resolution of 352 x 240 active
136
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D • Glossary of Terms
pixels and a refresh rate of 30 frames per second. Note that
MPEG-1 allows resolutions up to 4095 x 4095 active pixels;
however, there is a "constrained subset" of parameters defined
as SIF. The computer industry, which uses square pixels, has
defined SIF to be 320 x 240 active pixels, with a refresh rate of
whatever the computer is capable of supporting.
SMPTE time code – A standard for a signal being recorded to
uniquely identify each frame of the video signal. It is used to
control editing operations. (SMPTE stands for Society of
Motion Picture and Television Engineering).
Stream – The flow of data as a sequence of bits. It is also
referred to as bit stream.
Sub-carrier – A high-frequency carrier in a composite color
TV system, on which the chrominance information modulates
before combining with the luminance signal.
Subnet Mask – An extension of the IP addressing scheme that
allows a site to use a single IP network address for multiple
physical networks.
S-Video – A video signal that carries separate luminance and
chrominance signals.
Switch – In telecommunications, a switch is a network device
that selects a path or circuit for sending a unit of data to its next
destination. A switch may also include the function of the
router, a device or program that can determine the route and
specifically what adjacent network point the data should be sent
to. In general, a switch is a simpler and faster mechanism than a
router, which requires knowledge about the network and how to
determine the route
TCP – Refers to the Transport Control Protocol, used along
with the Internet Protocol (IP) to send data divided into data
packets over the Internet. While IP handles the actual delivery
of the data, TCP keeps track of the individual data packets for
efficiently routing data through the Internet.
Telnet – The TCP/IP standard protocol for remote terminal
service. TELNET allows a user at one site to interact with a
137
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D • Glossary of Terms
remote timesharing system at another site as if the user’s
keyboard and display connected directly to the remote machine.
Threshold – In a digital circuit, a dividing line between circuit-
signal levels representing different digital values.Time Base
Corrector – Equipment that corrects time base errors in video
tape recorders.
Time Base Errors – Analog artifacts being caused in video
tape recorders by non-uniform motion of the tape or the tape
head drum. It is typically visible as horizontal jitter or
instability of the reproduced picture.
Transform – In data compression, a process that converts a
block of data into some alternate form that is more convenient
or efficient.
True Color – Refers to the representation of color by varying
amounts of red, green, and blue. There are 256 shades for each
color available. If you mix all of them together, you obtain 16.7
million possible colors, hence the term True Color.
Truncation – Refers to the technique of reducing the number of
bits per pixel in compressing video (by throwing away some of
the least significant bits from each pixel).
UDP– Refers to the User Data Protocol, a transfer protocol
allowing any station on a network with a standard network card
to transmit or receive information, without the need for a
special interface card.
UDP Block Size – UDP Block size has to be understood as a
buffer that stores information, before it is sent to the network.
This ^buffer^ must hold at least one frame or two fields of
video information, before this information is really sent to the
network. This size is NOT the size of the frame that will be sent
to the network, because - when attached to a network - each
network interface card has its own rules regarding the frame
size. In Ethernet, this size is 1500 bytes. In ATM 53 bytes, and
in Frame Relay 6500 bytes. The network stack running on
MGW, NOT THE SOFTWARE decides the size of the frame
sent to the network. Optibase’s MPEG ComMotion 3.5/3.55 has
138
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D • Glossary of Terms
a checkbox for AUTO SET UDP BLOCK SIZE. Leave this box
checked unless there are many buffer overrun errors on the
transmitter. If this is the case, deselect this option and increase
the number displayed by about 10%. MPEG ComMotion PRO
does not provide any AUTO SET for the UDP Block size. The
size must be computed according to the following equation:
UdpBlockSize =(OutputBitRate/(8×35))×1.09
Unbalanced Audio – An analog signal consisting of a single
voltage relative to ground or common.
URL (Uniform Resource Locator) – A string that gives the
location of information. The string begins with a protocol type
(e.g. FTP) followed by the identification of specific information
(e.g. the domain name of a server and the path name to a file on
that server).
VBI (Vertical Blanking Interval) – Part of the television
signal that does not contain picture information and is not
visible on TV screens without a special decoder. VBI is used to
accommodate data such as closed captions.
VLAN - A virtual (or logical) LAN is a local area network with
a definition that maps workstations on some other basis than
geographic location (for example, by department, type of user,
or primary application). The virtual LAN controller can change
or add workstations and manage loadbalancing and bandwidth
allocation more easily than with a physical picture of the LAN.
Network management software keeps track of relating the
virtual picture of the local area network with the actual physical
picture. VLANs are being used with campus environment
networks.
VTR/VCR – Video Tape Recorder or Video Cassette Recorder,
a frame accurate recording and playback tape deck, usually of
professional capabilities.
WAV file – Refers to a sound file format for the PC being
widely used.
WINS – Refers to Windows Internet Naming Service and is
part of Microsoft Windows NT and 2000 Servers. It manages
139
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D • Glossary of Terms
the association of host names and locations with IP addresses
without an administrator having to be involved in each
configuration change. WINS automatically creates a host name-
IP address mapping entry in a table, ensuring that the respective
host name is unique and not a duplicate of someone else's
computer name. When a computer is moved to another
geographic location, the subnet part of the IP address is likely to
change. Using WINS, the new subnet information will be
updated automatically in the WINS table. WINS complements
the NT Server's DHCP protocol, which negotiates an IP address
for any computer (such as your workstation) when it is first
defined to the network. If you are a computer user on a network
connected to a Windows NT or Windows 2000 Server, you may
find WINS mentioned in some of your network-related
programs or system messages.
WMA – Windows Media Audio
WMS – External Windows Media Server, used to broadcast
WMT streams.
WMT – Windows Media Technology
Workgroup – A group of users who work on a common project
and share information on PCs interconnected over a local area
network (LAN).
140
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Re-Login, 66
Audio Bit-rates
At 32 kHz, 101
At 44.1 kHz, 102
At 48 kHz, 102
Remove - channel, 61
Restart, 63
Save - channel as
template, 61
Audio Input
Save - template, 78
Select All, 61, 75
Stop, 61
AES/EBU, 69, 100
Sampling rates, 69, 101
Source, 69
SW Version, 66
Templates, 66, 77
Video, 74
Unbalanced, 69
Buttons
View - channel, 61, 75
Add - channel, 61
Add - configuration, 80
Add - target, 73
Add - template, 77
Add Channel, 66, 73
Audio, 74
Cables
MiniDIN, 18
Network, 6
RCA Coaxial, 19
Serial, 6, 20
Configs, 66
Stereo MiniJack, 19
Video BNC, 18
Del - channel, 75
Del - configuration, 80
Del - target, 73
Channels
Adding, 73
Del - template, 78
Edit - channel, 61, 75
Edit - target, 74
Editing, 75
Templates, 77
Viewing errors, 76
Viewing profile, 76
Edit channel while
playing, 75
Chassis
Dimensions, 97
Play, 61
Refresh, 63, 71
Download from Www.Somanuals.com. All Manuals Search And Download.
Rack-mounting, 10
Weight, 97
Audio Buffer Window,
84
Audio Format, 84
Audio Mode, 84
Bit-rate, 81
Config Utility, 7
Configuration PC, 2, 8
Configuring NICs, 34
Changing parameters
while playing, 85
Current settings, 37, 63
Dup Bottom Lines, 83
Dup Top Lines, 83
Fixed Bit-rate, 82
Format, 100
Connectors
ANALOG AUD, 15
COMP.VID, 15
DIG AUD, 15
Network, 12, 98
Power, 14
Format, 81
Frame Drop Step, 82
Frame Sampling, 82
Intra Period, 83
RJ-45, 12
SCSI, 12, 98
Max video bit-rate, 70
Resolutions, 71, 101
Smooth Filter, 83
SDI, 15
Serial (RS-232), 12, 98
S-VIDEO, 15
Video Buffer Window,
83
Constant bit-rate, 82
DNS, 31
WMA, 70
WMT, 70
DNS IP address
Adding, 33
Encoding module
MGE-400, 15
Removing, 33
MGE-400D, 15
EMS Users
Adding, 57
Encoding Modules
Dimensions, 100
Installing, 16
Current, 58
Default, 54
Editing, 57
Removing, 17
Forcing out, 58
Max. allowed, 54
Password list, 104
Removing, 57
Specifications, 100
EncodingDCT Filter, 83
Error messages, 110
Fans, 97
Encoder state, 71
FTP mode, 44
Help file, 7
Encoding
Audio bit-rate, 84
Hostname
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing, 25
In the EMS, 62
DNS options, 31
IP address, 34
Reset to default, 38
Setting via Telnet, 45
Viewing settings, 37
WINS server, 35
HyperTerminal, 20
Required settings, 21
Initializing, 23
If DHCP disabled, 34
Network protocols, 99
NTSC, 67
LEDs
Alarm, 12, 13
Channels, 12, 13
Ethernet Link, 13
Ethernet Transmit, 13
Front, 13
Operating temperature, 98
PAL, 67
Passwords
Administrator, 27
For new EMS users, 57
Power, 13
Source, 15
Playing
LEDs in MGW 2400 EMS
Alarm, 60
Multicast streams, 92
Unicast streams, 93
Channels, 60
Fans, 60
Power consumption, 97
Power Cord, 6
Network, 60
Offline, 66
Power supply, 11, 97
Privilege, 66
Online, 66
Power, 60
Processing. See Encoding
Receiving. See Playing
Receiving client, 2
Resolutions, 71, 101
RJ-45, 98
Source, 60
Logging off, 58
Logging on, 55
To a different unit, 56
Management, 99
RJ-45 Link. See NICs
Management PC, 2, 8
MGW 2400 EMS, 2, 7, 8
RS-232, 2. See Connectors,
serial
Network Mode
Selecting, 28
Viewing, 30
Safety standards, 98
Saving configurations, 79
SCSI
Network parameters
Default gateway, 35
Connecting, 41
Download from Www.Somanuals.com. All Manuals Search And Download.
Connector, 12
Disabling share, 43
Disk, 6
Targets - Unicast
External WMS, 89
Host URL, 89
Enabling share, 42
Preparing, 41
Max Clients, 89
UDP Block Size, 89
SECAM sources, 18
Telnet, 2, 8, 45
Sources
Time and date, 39
UDP block size, 113
Upgrading MGW 2400, 94
Analog audio, 19
Composite, 18
Digital audio, 19
SDI, 18
Video Input
Brightness, 68
S-Video, 18
Color system, 67, 100
Composite, 67, 100
Contrast, 68
Standard compliance, 100
Status displays
Connected unit, 66
User profile, 66
Detect color system, 68
Detect source, 67
Hue, 68
Storage temperature, 98
System defaults, 103
Saturation, 68
SDI, 15, 67, 100
Sharpness filter, 68
S-Video, 67, 100
Targets - File
File name, 90
Password, 90
Storage. See SCSI
User name, 90
Voltage, 97
Windows Media Player, 2,
8, 52
Targets - Multicast
External WMS, 86
NSC files, 88
Windows Media Server, 8
Configuring, 64
Name/IP address, 65
Password, 65
Output interface, 87
Password, 88
Required network
mode, 28
Port, 87
Target IP address, 87
UDP Block Size, 87
User name, 88
User name, 65
Windows Media Services,
8, 52
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Support
Optibase's Extended Warranty program is a support package for
Optibase products and provides one to four years of warranty
starting with the day of purchase. For more details and first-line
support, contact the reseller or distributor who sold you your
Optibase product.
The Optibase Knowledge Base offers technical tips and
information about Optibase products. The Knowledge Base is
If you purchased your Optibase product directly from Optibase
Inc., contact Optibase’s technical support directly as follows:
Optibase Inc.
Tel: (800) 451 5101
Fax: (650) 691 9998
Software Updates
Software resources and updates are available for download at
Documentation
For errors or suggestions regarding this user manual, contact
Optibase’s documentation team directly at
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty
Your Optibase product is warranted against defects in material
and workmanship for a period of 12 months starting with the
date of delivery. We will repair or replace (at our option) any
part that proves defective during the warranty period, provided
the entire unit is returned to Optibase by prepaid shipping in
Optibase’s original packing.
Note that you are only eligible for warranty, if your MGW unit
carries a serial number on its rear panel. Your dated sales
receipt or invoice proves the date you purchased the unit.
Before returning your product for repair, contact our Customer
Service department for a Return Materials Authorization
(RMA) number. No unit will be accepted for repair without
RMA number.
Neither Optibase Inc. nor Optibase Ltd. will be responsible for
any damages resulting from the use, maintenance or installation
of any Optibase product. Neither Optibase Inc. nor Optibase
Ltd. will be responsible for the incorporation of any spare or
replacement parts not approved by Optibase. Without limiting
the generality of the foregoing, Optibase reserves the right to
refuse warranty repair on any product that, in our opinion, has
been subjected to any abnormal electrical, mechanical, or
environmental abuse, or shows signs of modification by an
unauthorized person or company. To assure coverage under this
warranty, you must fax your Warranty Registration Fax-Back
Sheet to Optibase, within 30 days of purchase of the product
along with a copy of your sales receipt. Call your local
distributor or reseller for out-of-warranty repair charge
estimates prior to returning a product.
Serial Number:
Date of Purchase:
Download from Www.Somanuals.com. All Manuals Search And Download.
|