INSTRUCTION MANUAL
Automatic Blood Pressure Monitor
with ComFit™ Cuff
Model BP755
BP755
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Thank you for purchasing Omron® BP755 IntelliSense® Automatic
Blood Pressure Monitor with the ComFit™ Cuff.
Fill in for future reference.
DATE PURCHASED: __________________
SERIAL NUMBER: ____________________
Staple your purchase receipt here
Your new digital blood pressure monitor uses the oscillometric method
of blood pressure measurement. This means the monitor detects your
blood’s movement through your brachial artery and converts the
movements into a digital reading. An oscillometric monitor does not
need a stethoscope so the monitor is simple to use.
The BP755 comes with the following components:
• Monitor
• AC Adapter
• ComFit™ Cuff
• Storage Case
• Quick Start Guide
• Instruction Manual printed in English and Spanish
The BP755 IntelliSense® Automatic Inflation Blood Pressure Monitor is
intended for home use.
SAVE THESE INSTRUCTIONS
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
To assure the correct use of the product, basic safety measures should
always be followed including the warnings and cautions listed in this
instruction manual.
SAFETY SYMBOLS USED IN THIS INSTRUCTION MANUAL
Indicates a potentially hazardous situation
which, if not avoided, could result in death or
serious injury.
WARNING
Indicates a potentially hazardous situation
which, if not avoided, may result in minor or
CAUTION
moderate injury to the user or patient or
damage to the equipment or other property.
OPERATING THE DEVICE
Contact your physician for specific information about your blood
pressure. Self-diagnosis and treatment using measured results may be
dangerous. Follow the instructions of your physician or licensed
healthcare provider.
The monitor is not intended to be a diagnostic device.
If battery fluid should get in your eyes, immediately rinse with
plenty of clean water. Contact a physician immediately.
Read all of the information in the instruction manual and any other
literature in the box before operating the unit.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
OPERATING THE DEVICE (continued)
This device is intended for use in measuring blood pressure and
pulse rate in the adult population. Do not use this device on infants
or persons who cannot express their intentions.
Read the Special Conditions section (page 24) of the instruction
manual if your systolic pressure is known to be more than 220
mmHg. Inflating to a higher pressure than necessary may result in
bruising where the cuff is applied.
Operate the device only as intended. Do not use the device for any
other purpose.
Dispose of the device, components and optional accessories
according to applicable local regulations. Unlawful disposal may
cause environmental pollution.
Do not use a cellular phone near the device. It may result in an
operational failure.
Use only authorized parts and accessories. Parts and accessories not
approved for use with the device may damage the unit.
Use only 1.5 V “AA” alkaline batteries with this device. Do not use
other types of batteries. This may damage the unit.
RISK OF ELECTRICAL SHOCK
Do not plug or unplug the power cord into the electrical outlet with
wet hands.
Do not overload power outlets. Plug the device into the appropriate
voltage outlet.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
CARE AND MAINTENANCE
Do not subject the monitor to strong shocks, such as dropping the
unit on the floor.
Do not submerge the device or any of the components in water.
Store the device and the components in a clean, safe location.
Changes or modification not approved by the manufacturer will void
the user warranty. Do not disassemble or attempt to repair the unit or
components.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE TAKING A MEASUREMENT
To ensure a reliable reading follow these recommendations:
1. Avoid eating, drinking alcohol, smoking, exercising, and bathing for
30 minutes before taking a measurement. Rest for at least 15 minutes
before taking the measurement.
2. Stress raises blood pressure. Avoid taking measurements during
stressful times.
3. Measurements should be taken in a quiet place.
4. Remove tight-fitting clothing from your left arm.
5. Sit on a chair with your feet flat on the floor. Rest your left arm on a
table so that the cuff is at the same level as your heart.
6. Remain still and do not talk during the measurement.
7. Wait 2-3 minutes between measurements. The wait time allows the
arteries to return to the condition prior to taking the blood pressure
measurement. You may need to increase the wait time depending on
your individual physiological characteristics.
8. Keep a record of your blood pressure and pulse readings for your
physician. A single measurement does not provide an accurate
indication of your true blood pressure. You need to take and record
several readings over a period of time. Try to measure your blood
pressure at the same time each day for consistency.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions
KNOW YOUR UNIT
Main Unit:
Display
Battery Compartment
B
P
7
5
5
Start/Stop
Button
Memory Buttons
Air Jack
Date/Time Setting Button (
)
AC Adapter Jack
Components:
Air Tube
Thumb Grip
Air Plug (Connects to Air Jack)
Storage Case
Arm Cuff
Housing
Cord
INSTRUCTION MANUAL
Automatic Blood Pressure Monitor
with ComFit™ Cuff
Model BP755
BP
75
5
AC Adapter
Instruction Manual
Quick Start Guide
8
Download from Www.Somanuals.com. All Manuals Search And Download.
UNIT DISPLAY
Systolic Blood Pressure
Diastolic Blood Pressure
Heartbeat Symbol/
Hypertension Indicator
Memory Symbol
Average Value Symbol
Pulse Display
Deflation Symbol
Movement Error Symbol
Date/Time Display
Battery Low Indicator
Irregular Heartbeat Symbol
9
Download from Www.Somanuals.com. All Manuals Search And Download.
DISPLAY SYMBOLS
IRREGULAR HEARTBEAT SYMBOL (
)
When the monitor detects an irregular rhythm two or more times during
the measurement, the Irregular Heartbeat Symbol ( ) will appear on
the display with the measurement values.
Normal Heartbeat
An irregular heartbeat rhythm is defined
as a rhythm that is more than 25%
slower or 25% faster from the average
rhythm detected while the monitor is
measuring the systolic and diastolic
blood pressure.
Pulse
Blood
pressure
Irregular Heartbeat
Short Long
If the irregular heartbeat symbol (
)
Pulse
displays with your measurement results,
we recommend you consult your
physician. Follow the directions of your
doctor.
Blood
pressure
MOVEMENT ERROR SYMBOL (
)
The Movement Error Symbol ( ) is displayed if you move your body
during the measurement. Please remove the arm cuff, and wait
2-3 minutes, reapply the arm cuff and take another measurement.
AVERAGE VALUE SYMBOL (
)
The Average Value Symbol ( ) is displayed when you press the
Memory button. The most recent average reading appears on the display
screen.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
DISPLAY SYMBOLS
HEARTBEAT SYMBOL/HYPERTENSION INDICATOR
(
)
TAKING A MEASUREMENT
The Heartbeat Symbol ( ) flashes on the display during the
measurement. The Heartbeat Symbol ( ) flashes at every
heartbeat.
When the measurement is complete, the Heartbeat Symbol (
)
flashes on the display with your blood pressure and pulse rate if the
reading is above 135 for the Systolic Blood Pressure value and/or
above 85 for the Diastolic Blood Pressure value.
USING THE MEMORY FUNCTION
The Heartbeat Symbol ( ) flashes when the blood pressure
reading stored in the memory is above 135 for the Systolic Blood
Pressure value and/or above 85 for the Diastolic Blood Pressure
value.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
DISPLAY SYMBOLS
The American Heart Association recommends the following guideline
for upper limit of normal for home blood pressure readings:
AHA Home Guideline for Upper Limit of Normal BP
Systolic Blood Pressure
135 mmHg
Diastolic Blood Pressure
85 mmHg
This is a general guideline because blood pressure depends on
age and morbidity. The AHA recommends a lower home blood
pressure goal for certain patients, including diabetic patients,
pregnant women, and patients with renal failure1.
WARNING
The monitor is not intended to be a diagnostic device.
WARNING
Contact your physician for specific information about your blood
pressure. Self-diagnosis and treatment using measured results may
be dangerous. Follow the instructions of your physician or
licensed healthcare provider.
Omron Healthcare recommends you contact your physician if the
Heartbeat Symbol ( ) flashes on the display with your measurement
values.
1American Heart Association Scientific Statement 2004
12
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE AC ADAPTER
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
- DANGER -
TO REDUCE THE RISK OF
FIRE OR ELECTRIC SHOCK,
CAREFULLY FOLLOW THESE INSTRUCTIONS.
For connection to a power supply not in the U.S.A., use an
attachment plug adapter of the proper configuration for the
power outlet.
The power unit (AC Adapter) is intended to be correctly
oriented in a vertical or floor mount position.
NOTES: • Use only the authorized Omron AC Adapter that came with
this monitor.
• We recommend you install the batteries even if the AC
Adapter is used. If no batteries are installed, you may need
to reset the date and time if the AC Adapter is disconnected.
The measurement results will not be deleted.
CAUTION
Use only authorized parts and accessories. Parts and accessories not
approved for use with the device may damage the unit.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE AC ADAPTER
To connect the AC Adapter
① Insert the AC Adapter Plug into the AC Adapter Jack on the back side
of the monitor as illustrated.
② Plug the AC Adapter into a 120V AC outlet (60 cycles).
Housing
Cord
To disconnect the AC Adapter
① Hold and pull the housing to remove the AC Adapter from the
electrical outlet. Do not remove by pulling the cord.
② Remove the AC Adapter plug from the monitor.
WARNING
Do not plug or unplug the power cord into the electrical outlet with
wet hands.
CAUTION
Do not overload power outlets. Plug the device into the appropriate
voltage outlet.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
BATTERY INSTALLATION
NOTE: Use 4 new “AA” size batteries - long life alkaline batteries are
recommended.
1. Press the ▼ indicator on the battery cover
and slide the cover off in the direction of
the arrow.
2. Install 4 “AA” size batteries so the
+ (positive) and - (negative) polarities
match the polarities of the battery
compartment as indicated.
NOTE: 4 “AA” size batteries are not
included in this unit.
3. Replace the battery cover.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
BATTERY INSTALLATION
BATTERY REPLACEMENT
Low Battery Indicator
When the Low Battery Indicator appears on the display screen, turn the
monitor off and remove all the batteries. Replace with four new batteries
at the same time. Long-life alkaline batteries are recommended.
WARNING
If battery fluid should get in your eyes, immediately rinse with
plenty of clean water. Contact a physician immediately.
NOTES: • Turn the unit off before replacing the batteries. If the
batteries are removed while the unit is still on, the date and
time will be reset to that of the previous use. However, the
measurement results are not deleted.
• When the batteries are replaced, you may need to reset the
date and time. If the year is flashing on the display screen,
refer to “Setting the Date and Time”.
CAUTION
Dispose of the device, components and optional accessories
according to applicable local regulations. Unlawful disposal may
cause environmental pollution.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING THE DATE AND TIME
Set the monitor to the current date and time before taking a measurement
for the first time. If the current date and time are not set correctly, the
measurement values stored in the memory and the average values may
not be correct.
1. TO START THE SETTING
Press the Date/Time Setting
button ( ) to adjust the date
and time.
®
The year flashes on the display.
2. SETTING THE YEAR
The year can be set between
2006 and 2030.
When the display reaches 2030, it will return
to 2006.
Press the Memory Up button
by increments of one year.
to advance
Press the Date/Time Setting button ( ) to set
the current year.
®
The month flashes on the display.
NOTES: • Press the Memory Down button
to decrease the day
and time values by increments of one.
• Press and hold the Memory button to increase or decrease
the date and time values faster.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING THE DATE AND TIME
3. SETTING THE MONTH
Press the Memory Up button
of one month.
to advance by increments
Press the Date/Time Setting button ( ) to set
the current month.
®
The day flashes on the display.
4. SETTING THE DAY
Press the Memory Up button
by increments of one day.
to advance
Press the Date/Time Setting button ( ) to set
the current day.
®
The hour flashes on the display.
5. SETTING THE HOUR
The time is set using AM or PM.
Press the Memory Up button
of one hour.
to advance by increments
Press the Date/Time Setting button ( ) to set
the current hour.
The minutes flash on the display.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING THE DATE AND TIME
6. SETTING THE MINUTE
Press the Memory Up button
of one minute.
to advance by increments
Press the Date/Time Setting button ( ) to set the current minute.
The year flashes on the display.
7. TO TURN THE MONITOR OFF
Press the START/STOP button.
NOTE: The monitor will automatically turn off after the minute has
been set after battery replacement.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
APPLYING THE ARM CUFF
CAUTION
Read all of the information in the instruction manual and any other
literature in the box before operating the unit.
CAUTION
This device is intended for use in measuring blood pressure and
pulse rate in the adult population. Do not use this device on infants
or persons who cannot express their intentions.
APPLYING THE CUFF ON THE LEFT ARM
1. Make sure the air plug is securely inserted in the main unit.
T
R
A
T
S
P
O
T
S
Y
R
O
M
E
M
2. Remove tight-fitting clothing from your upper arm.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
APPLYING THE ARM CUFF
Thumb Grip
3. Hold the thumb grip on the cuff
securely with your hand.
Cloth Fastening
4. Turn the palm of your hand upward.
5. Apply the cuff to your left upper arm so the blue stripe is on the
inside of your arm and aligned with your middle finger. The air tube
runs down the inside of your arm. The bottom of the cuff should be
approximately 1/2" above your elbow.
Left Arm
Blue Stripe
1/2 inch (1 - 2 cm)
Air Tube
21
Download from Www.Somanuals.com. All Manuals Search And Download.
APPLYING THE ARM CUFF
6. Wrap the cuff firmly in place around your arm using the cloth
fastening.
APPLYING THE CUFF ON THE RIGHT ARM
When taking a measurement using the right arm use this instruction
for Step 5.
Apply the cuff to your right upper arm so the thumb grip is centered on
the inside of your inner arm. The bottom of the cuff should be
approximately 1/2'' above your elbow.
Right Arm
Thumb Grip
NOTE: Be careful not to rest your arm on the air tube. This will restrict
the flow of air to the cuff.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
TAKING A MEASUREMENT
The monitor automatically determines your ideal inflation level. In rare
circumstances when a higher inflation may be necessary, the monitor
automatically re-inflates the cuff up to 30mmHg higher than the initial
inflation and restarts the measurement.
1. Sit on a chair with your feet flat on the floor. Place your arm on a
table so the cuff is level with your heart.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
TAKING A MEASUREMENT
2. Press the START/STOP button.
All display symbols appear on the screen.
The cuff starts to inflate automatically. As the cuff inflates, the
monitor automatically determines your ideal inflation level.
Remain still and do not move your arm until the entire measurement
process is completed.
®
NOTE: To stop the inflation or measurement, push the START/STOP
button. The monitor will stop inflating, start deflating, and will
turn off.
3. Inflation stops automatically and the measurement is started.
As the cuff deflates, decreasing
numbers appear on the display
and the Heartbeat Symbol (
flashes.
)
24
Download from Www.Somanuals.com. All Manuals Search And Download.
TAKING A MEASUREMENT
4. When the measurement is complete, the arm
cuff completely deflates. Your blood pressure
and pulse rate are displayed.
5. Press the START/STOP button to
turn the monitor off.
NOTE: The monitor will automatically
®
turn off after five minutes.
SPECIAL CONDITIONS
CAUTION
Inflating to a higher pressure than necessary may result in bruising
where the cuff is applied.
If your systolic pressure is known to be more than 220 mmHg,
press and hold the START/STOP button until the monitor inflates
30 to 40 mmHg higher than your expected systolic pressure.
®
NOTES: • Do not apply more pressure than necessary.
• The monitor will not inflate above 299 mmHg.
When the measurement is complete, the arm cuff completely deflates.
Your blood pressure and pulse rate are displayed.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE MEMORY FUNCTION
Every time you complete a measurement the monitor stores the blood
pressure and pulse rate in the memory. The monitor automatically stores
up to 90 sets of measurement values (blood pressure and pulse rate).
When 90 sets of measurement values are stored, the oldest record is
deleted to save the most recent values.
ADVANCED AVERAGING FUNCTION
The monitor calculates the average reading based on the three most
recent sets of measurement values taken within 10 minutes of the most
recent reading.
TO DISPLAY THE AVERAGE VALUE AND THE MEASUREMENT VALUES
NOTE: If two sets of measurement values are stored in the memory for
the 10 minute period, the average is based on the two sets of
measurement values. If one set of measurement value is stored,
this is displayed as the average.
1. Press the Memory Down button
. The average value symbol
(
) appears on the display when the average reading is shown.
®
26
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE MEMORY FUNCTION
2. Press the Memory Down button
set of measurement values on the screen.
to display the most recent
to display the oldest set of
Press the Memory Up button
measurement values.
®
Alternating display
NOTES: • The date and time are alternately displayed with the
measurement values.
• Press the button repeatedly to display the next values.
• Press and hold the button to display the values faster.
3. Press the START/STOP button to turn the power off.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE MEMORY FUNCTION
TO DELETE ALL VALUES STORED IN THE MEMORY
You cannot partially delete values stored in the memory.
All values will be deleted.
1. While holding the Memory Down button
, press the
START/STOP button down for more than 2 seconds until the display
appears as it does in the following illustration.
®
2. Press the START/STOP button to turn the monitor off.
NOTE: The monitor will automatically turn off after five minutes.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Maintenance
CARE AND MAINTENANCE
To keep your digital blood pressure monitor in the best condition and
protect the unit from damage, follow the directions listed below:
Keep the monitor in the storage case
when not in use. Make sure the AC Adapter
is placed under the main unit so that is does
not damage the display.
Do not forcefully bend the arm cuff
or air tube. Do not fold tightly.
Clean the monitor with a soft dry cloth.
Do not use any abrasive or volatile cleaners.
Do not attempt to clean the cuff.
CAUTION
Do not submerge the device or any of the components in water. Do
not subject the monitor to extreme hot or cold temperatures,
humidity or direct sunlight.
CAUTION
Store the device and the components in a clean, safe location.
CAUTION
Do not subject the monitor to strong shocks, such as dropping the
unit on the floor.
Remove the batteries if the unit will not be used for three months or
longer. Always replace all the batteries with new ones at the same time.
Use the unit consistent with the instruction provided in this manual.
Use only authorized parts and accessories.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
Use the unit in a manner consistent with the instructions provided
in this manual.
CAUTION
Use only Omron authorized parts and accessories. Parts and
accessories not approved for use with the device may damage the
unit.
CAUTION
Changes or modification not approved by the manufacturer will void
the user warranty. Do not disassemble or attempt to repair the unit or
components.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
ERROR INDICATORS AND TROUBLESHOOTING TIPS
SYMBOL
CAUSE
CORRECTION
Take another measurement and
remain still until the
measurement is complete.
Monitor could not
detect pulse wave.
Cuff under-inflated.
Cuff not applied
correctly.
Remove the arm cuff.
Read “Taking a Measurement”.
Wait 2-3 minutes.
Cuff over-inflated.
Batteries are worn.
Take another measurement.
Replace the four batteries. Refer
to “Battery Installation”.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
ERROR INDICATORS AND TROUBLESHOOTING TIPS
PROBLEM
CAUSES AND SOLUTIONS
No power.
Replace all four batteries with new
ones.
No display appears on the unit. Check the battery installation
for proper placement of the
battery polarities.
Blood pressure varies constantly.
Many factors including stress, time
of day, how you wrap the cuff, may
affect your blood pressure.
Review the sections “Before Taking
Measurement values appear
too high or too low.
a Measurement” and “Taking a
Measurement”.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC STATEMENT
Note:
POTENTIAL FOR RADIO/TELEVISION INTERFERENCE (for U.S.A. only)
This product has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. The product generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If the product does cause harmful interference to radio or television
reception, which can be determined by turning the product on and off, the
user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the product and the receiver.
• Connect the product into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
POTENTIAL FOR RADIO/TELEVISION INTERFERENCE (for Canada only)
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus as set out in the interference-causing equipment
standard entitled “Digital Apparatus”, ICES-003 of the Canadian Department of
Communications.
Cet appareil numérique respecte les limites de bruits radioeléctriques
applicables aux appareils numériques de Clase B prescrites dans la norme sur le
materiel brouilleur: “Appareils Numériques”, ICES-003 édictée par le minister
des communications.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
LIMITED WARRANTIES
Your BP755 IntelliSense® Automatic Blood Pressure Monitor, excluding the arm cuff, is
warranted to be free from defects in materials and workmanship appearing within 5 years
from the date of purchase, when used in accordance with the instructions provided with
the monitor. The arm cuff is warranted to be free from defects in materials and
workmanship appearing within one year from the date of purchase when the monitor is
used in accordance with the instructions provided with the monitor. The above warranties
extend only to the original retail purchaser.
We will, at our option, repair or replace without charge any monitor or arm cuff covered
by the above warranties. Repair or replacement is our only responsibility and your only
remedy under the above warranties.
To obtain warranty service contact Customer Service by calling 1-800-634-4350 for the
address of the repair location and the return shipping and handling fee.
Enclose the Proof of Purchase. Include a letter, with your name, address, phone number,
and description of the specific problem. Pack the product carefully to prevent damage in
transit. Because of possible loss in transit, we recommend insuring the product with return
receipt requested.
ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF THE
APPLICABLE WRITTEN WARRANTY ABOVE. Some states do not allow
limitations on how long an implied warranty lasts, so the above limitation may not apply
to you.
OMRON SHALL NOT BE LIABLE FOR LOSS OF USE OR ANY OTHER
INCIDENTAL, CONSEQUENTIAL OR INDIRECT COSTS, EXPENSES OR
DAMAGES. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above exclusions may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which
may vary from state to state.
FOR CUSTOMER SERVICE
Visit our web site at:
Call toll free:
1-800-634-4350
34
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Model:
BP755 (HEM-7000-Z4CS)
Display:
LCD Digital Display
Measurement Range:
Accuracy/Calibration:
Pressure: 0 to 299 mmHg, Pulse: 40 to 180/min.
Pressure: 3mmHg or 2% of reading
Pulse: 5% of reading
Inflation:
Automatic by electric pump
Deflation:
Automatic pressure release valve
Automatic exhaust valve
Capacitive pressure sensor
Rapid Air Release:
Pressure Detection:
Measurement Method:
Pulse Wave Detection:
Power Source:
Battery Life:
Operating Temperature
/Humidity:
Oscillometric method
Capacitance type pressure sensor
120V 60Hz AC Adapter (or 4 “AA” batteries)
Approx. 1500 uses with 4 new alkaline batteries
50ºF to 104ºF (10ºC to 40ºC) /15 to 90% RH
Storage Temperature
/Humidity/Air Pressure:
Main Unit Weight:
-4ºF to 140ºF (-20ºC to 60ºC) /10 to 95% RH
700-1060 hPa
Approximately 12 1/2 oz. (355 g)
not including batteries
Main Unit Dimensions:
Cuff Size:
Approx. 6 3/32" (l) x 5 5/32" (w) x 3 5/16" (h)
(155 mm x 131 mm x 84 mm)
Approximately 6" (w)(152 mm)
Cuff tube 23 5/8" (l) (600 mm)
Fits arm circumferences 9" to 17"
(220mm to 420mm)
Cuff Circumference:
Memory:
Contents:
Up to 90 readings
Main Unit, ComFitTM Cuff, AC Adapter,
Instruction Manual, Quick Start Guide, and
Storage Case
= Type B
NOTE: These specifications are subject to change without notice.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Manufactured by OMRON HEALTHCARE
Made in China
Distributed by:
OMRON HEALTHCARE, INC.
1200 Lakeside Drive
Bannockburn, Illinois 60015
Copyright © 2009 Omron Healthcare, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|