National Instruments Network Router WAP 3701 User Manual

NI WAP-3701/3711  
User’s Manual  
First Edition, Sept 2007  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1
Chapter  
1
Introduction  
The NI WAP-3701/3711 enables wireless users to access network resources wirelessly. The NI  
WAP-3701/3711 can authenticate and authorize wireless users by IEEE 802.1X and RADIUS, and  
communicate with a back-end RADIUS (Remote Authentication User Dial-In Service) server to  
determine if a wireless user is allowed to access the wireless network..  
The following topics are covered in this chapter:  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
NI WAP-3701/3711 User’s Manual  
Introduction  
Overview  
NI WAP-3701/3711 is rated to operate at temperatures ranging from 0 to 60°C, and is rugged  
enough for any harsh industrial environment. It can be installed easily on DIN-Rail mounting as  
well as in distribution boxes. The DIN-Rail mounting capability, wide operating temperature range,  
and the IP30 case with LED indicators make the NI WAP-3701/3711 a ready, plug-and-play, yet  
reliable solution for your Industrial Wireless application.  
Package Checklist  
The NI WAP-3701/3711 is shipped with the following items. If any of these items is missing or  
damaged, please contact your customer service representative for assistance.  
y
y
y
y
1 × NI WAP-3701/3711 802.11g/b Wireless AP/Bridge/Client  
2 × Swivel Type Antenna (2 dBi RP-SMA)  
Quick Installation Guide  
Document & Software CD (includes User’s Manual and Windows Utility)  
Product Features  
y
y
y
y
y
IEEE 802.11b/g Compliant  
Redundant 24 VDC power inputs or Power-over-Ethernet  
Powerful security with WPA/802.1X/MAC address filtering  
DIN-Rail mounting capability  
Casing design meets IP30 protection standard  
Product Specifications  
WLAN  
Standards  
IEEE802.11g/b for wireless LAN, IEEE802.3u 10/100BaseTX  
for Ethernet LAN, IEEE802.3af for Power over Ethernet  
Frequency Range  
2.4-2.4835 GHz, Direct Sequence Spread Spectrum (DSSS)  
Data Rate & Modulation  
OFDM@54Mbps, CCK@11/5.5Mbps, DQPSK@2Mbps and  
DBSK@1Mbps  
Operating Channels  
Security  
USA: 1-11 (FCC) / Europe: 1-13 (ETSI)  
64-bit and 128-bit WEP encryption, WPA (IEEE  
802.1X/RADIUS and TKIP)  
Data Rates  
1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54 Mbps  
Transmit Power  
802.11b:  
17dBm  
802.11g:  
6/9Mbps17dBm, 12/18Mbps15dBm,  
24Mbps14dBm, 36Mbps14dBm,  
48Mbps12dBm, 54Mbps12dBm  
Receiver Sensitivity  
802.11b:  
8% FER@1Mbps-91dBm,  
8% FER@2Mbps-88dBm  
8% [email protected]-85dBm,  
8% FER@11Mbps-83dBm  
1-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
NI WAP-3701/3711 User’s Manual  
Introduction  
802.11g:  
10% PER@6Mbps-88dBm,  
10% PER@9Mbps-87dBm  
10% PER@12Mbps-84dBm,  
10% PER@18Mbps-82dBm  
10% PER@24Mbps-79dBm,  
10% PER@36Mbps-75dBm  
10% PER@48Mbps-69dBm,  
10% PER@54Mbps-68dBm  
Software Features  
Protocols  
HTTP, DHCP, TCP/IP, RADIUS, DNS, NetBIOS, NetBEUI,  
AppleTalk, and IPX/SPX  
Configuration  
Web-based management  
Client OS Support  
Windows 95/98/2000/ME/NT/XP, Unix, and Macintosh  
Interface  
Antenna  
2dBi diversity antenna with an R-SMA connector  
10/100BaseT(X) auto negotiation speed  
RJ45 port  
LED Indicators  
PWR1, PWR2, WLAN (Link/ACT), LAN (Link/ACT)  
Power  
Input Voltage  
12 to 45 VDC; Redundant dual DC power inputs or Power over  
Ethernet (PoE, power on RJ45 pins 4, 5 for power + and pins 7, 8  
for power -)  
Input Current (@24V)  
Connection  
0.3A  
Removable Terminal Block  
Overload Current Protection  
Reverse Polarity Protection  
1.6A  
Present  
Mechanical  
Casing  
IP30 protection, metal case  
DIN-Rail or panel mounting  
Installation  
Environment  
Operating Temperature  
Storage Temperature  
0 to 60°C (32 to 140°F)  
-20 to 70°C (-4 to 158°F)  
5 to 95% (non-condensing)  
Ambient Relative Humidity  
Regulatory Approvals  
Safety  
UL60950-1, CSA C22.2 No. 60950-1, EN60950-1, TUV  
UL/cUL Class I, Division 2, Groups A, B, C, and D  
FCC, CE, SRRC  
Hazardous Location  
Emissions  
1-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2
Chapter  
2
Getting Started  
This chapter explains how to install the NI WAP-3701/3711 for the first time.  
The following topics are covered:  
¾
¾
¾
¾
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
NI WAP-3701/3711 User’s Manual  
Getting Started  
First-Time Installation and Configuration  
Before installing the NI WAP-3701/3711, check to make sure that all items in the Package  
Checklist are in the box. In addition, you will need access to a notebook computer or PC equipped  
with an Ethernet port. The NI WAP-3701/3711 has a default IP address that you must use when  
connecting to the NI WAP-3701/3711 for the first time.  
For testing requirements, if you only have one NI WAP-3701/3711, we strongly suggest that you  
prepare a notebook computer or PC with a wireless LAN adapter installed. After finishing the  
installation and configuration, you should test the NI WAP-3701/3711 to make sure the wireless  
transmission is working normally.  
NOTE  
NOTE  
Step 1: Select the Power Source  
The NI WAP-3701/3711 can be powered by a DC power input, or by PoE (Power over Ethernet).  
The NI WAP-3701/3711 will use the power source that you choose.  
The PoE capability of the bridge is PowerDsine-compatible. Please visit PowerDsine’s website  
for more information (http://www.powerdsine.com).  
Step 2: Connect the NI WAP-3701/3711 to a notebook or PC  
Since the NI WAP-3701/3711 supports MID/MID-X auto-sensing, you can use either a  
straight-through cable or cross-over cable to connect the NI WAP-3701/3711 to the notebook. If  
the LAN LED on the NI WAP-3701/3711’s front panel lights up, it means the connection is  
established.  
Step 3: Set up the computer’s IP address  
In a Windows environment, the computer’s IP address can be changed in the TCP/IP settings  
window. Select an IP address on the same subnet as the NI WAP-3701/3711. Since the NI  
WAP-3701/3711’s default IP address is 192.168.127.253, and the subnet mask is 255.255.255.0,  
you should set the IP address of the computer to 192.168.127.xxx.  
Step 4: Use the web-based manager to configure the NI WAP-3701/3711  
Open your computer’s web browser and type http://192.168.127.253 in the address box to access  
the homepage of the web-based Network Manager. Before the homepage opens, you will need to  
enter the user name and password as shown in the following figure. For first-time configuration,  
enter the default user name and password and then click on OK:  
Default user name & password  
User name:  
Password:  
admin  
root  
192.168.127.253  
2-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
NI WAP-3701/3711 User’s Manual  
Getting Started  
For security reasons, we strongly recommend changing the password. To do this, open the  
Network Manager homepage, click on General Æ Password, and then follow the onscreen  
NOTE  
instructions.  
Step 5: Select the Operational Mode for NI WAP-3701/3711  
By default, the NI WAP-3701/3711’s operation mode is set to AP/Bridge. If you want to change  
the setting, click on General Æ Operational Mode, as shown in the following figure, select an  
operation mode, and then click on Save to activate the change.  
Go to the General, Operational Mode section, select an operational mode and then click Save at  
the bottom of this page. This will take you back to the starting page.  
The AP supports 2 operational modes:  
y
y
AP/Bridge  
This mode provides both Access Point and Static LAN-to-LAN Bridging functionality. The  
static LAN-to-LAN bridging function is supported through WDS (Wireless Distribution  
System).  
AP Client  
This mode is for Dynamic LAN-to-LAN Bridging. The AP Client automatically establishes  
bridge links with APs from any vendors. In either mode, the NI WAP-3701/3711 forwards  
packets between its Ethernet interface and wireless interface for wired hosts on the Ethernet  
side and wireless host(s) on the wireless side.  
Detailed information about configuring the NI WAP-3701/3711’s Operation Mode is given in  
Chapter 3.  
NOTE  
2-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NI WAP-3701/3711 User’s Manual  
Step 6: Configure the NI WAP-3701/3711’s IEEE 802.11 settings  
Getting Started  
Go to the IEEE 802.11 Communication section to configure IEEE 802.11g-related communication  
settings, including Regulatory domain, Channel number, and Network name (SSID).  
The number of available RF channels depends on local regulations; therefore, you will need to  
choose an appropriate regulatory domain to comply with local regulations. The SSID of a wireless  
client computer and the SSID of the NI WAP-3701/3711 must be identical for them to be able to  
communicate with each other.  
When you are finished, click on Save at the bottom of the page. This will return you to the home  
page.  
Step 7: Review and Apply Settings  
On the home page, you can review all of the settings you have made. Changes are highlighted in  
red. If the changes are okay, click on Restart to restart the NI WAP-3701/3711 for the new  
settings to take effect.  
About 10 seconds are needed for the AP to complete its restart process.  
NOTE  
2-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NI WAP-3701/3711 User’s Manual  
Getting Started  
Deploying the Access Point (AP)  
After the settings have been configured, deploy the AP to the field application environment.  
Connect the AP to an Ethernet LAN through an Ethernet switch or hub.  
If you are configuring a pair of NI WAP-3701/3711 units for AP mode for a dynamic or static  
bridging application and external high-gain directional antennas are used, it is difficult to adjust  
alignments of the antennas when the two devices are separated by a long distance.  
To adjust the alignments of a pair of bridges’ directional antennas:  
1. Connect each bridge to a computer via Ethernet  
2. Configure the date rate of each bridge to the lowest value, 1 Mbps.  
3. Fix the alignment of the antenna on one side.  
4. Adjust the alignment of the antenna on the other side by using response time information  
obtained by pinging (i.e., running PING.exe) the “fixed-side” computer.  
5. Fine-tune the alignment of the antenna until you get a best response time.  
6. Increase the data rate of each bridge simultaneously until a maximum workable data rate is  
reached. You may not be able to use the highest data rate, 54 Mbps, because of the distance  
and the gain of the antennas.  
Adjust antenna alignment  
WDS Link  
Bridge 1  
Bridge 2  
PING (ICMP Echo Request)  
ICMP Echo Reply  
Computer 1  
Computer 2  
Setting up Client Computers  
The TCP/IP and IEEE 802.11g-related settings of wireless client computers must match those of  
the Access Point.  
Configuring IEEE 802.11g-related Settings  
Open Internet Explorer and type the NI WAP-3701/3711’s IP address in the Address field. Press  
Enter to establish the connection.  
Before the TCP/IP networking system of a wireless client computer can communicate with other  
hosts, the underlying wireless link must be established between this wireless computer and an  
Access Point.  
To establish a wireless link to an Access Point:  
1. Launch the configuration/monitoring utility provided by the vendor of the installed WLAN  
NIC.  
2. Use the utility to make appropriate Operating Mode, SSID, and WEP settings.  
2-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
NI WAP-3701/3711 User’s Manual  
Getting Started  
A wireless client computer must be in infrastructure mode to associate with an AP.  
NOTE  
NOTE  
The SSID of the wireless client computer and the SSID of the AP must be identical. Or, if the  
SSID broadcast capability of the AP is enabled (default setting), the SSID of the wireless client  
computer could be set to “any.”  
Both the wireless client computer and the Access Point must have the same WEP settings for  
them to communicate with each other.  
NOTE  
NOTE  
For better wireless security, IEEE 802.1X capability of the Access Point must be enabled so that  
only authenticated wireless users can access the wireless network.  
Configuring TCP/IP-related Settings  
Use the Windows Network Control Panel Applet to change the TCP/IP settings of the client  
computers so that the IP addresses of the client computers and the IP address of the Access Point  
are in the same IP subnetwork.  
If a client computer is originally set up with a static IP address, you can either change its IP  
address to match the IP address of the Access Point, or select the option  
“automatically-obtain-an-IP-address” if there is a DHCP server on the network.  
For some versions of Windows, the computer needs to be restarted for the new TCP/IP settings to  
take effect.  
NOTE  
Confirming the Settings of the AP and Client Computers  
After you have completed deploying the Access Point and setting up client computers, you must  
make sure the settings you have made are correct.  
Checking if the IEEE 802.11g-related Settings Work  
To check if a wireless client computer can associate with the NI WAP-3701/3711:  
1. Launch the configuration/monitoring utility provided by the vendor of the installed WLAN  
NIC.  
2. Check if the client computer is associated to an NI WAP-3701/3711. If the check fails, see  
Appendix B, “Wireless Settings Problems,” to troubleshoot the problem.  
Checking if the TCP/IP-related Settings Work  
To check if a client computer can assess the Internet:  
1. Open a Windows Command Prompt window on the client computer.  
2. Type ping AP”, where AP is the IP address of the Access Point. Replace it with your real IP  
address—for example, 192.168.127.253, and then press Enter.  
If the AP responds, go to the next step; otherwise see Appendix B, “TCP/IP Settings  
Problems” to troubleshoot the problem.  
2-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
NI WAP-3701/3711 User’s Manual  
Getting Started  
3. Type ping default_gateway”, where default_gateway is the IP address of the default gateway  
of the wireless client computer, and then press Enter. If the gateway responds, go to the next  
step; otherwise, see Appendix B, “TCP/IP Settings Problems,” to troubleshoot the problem.  
4. Type ping 1st_dns_server”, where 1st_dns_server is the IP address of the primary DNS  
server of the wireless client computer, and then press Enter. If this DNS server responds, go  
to the next step; otherwise, see Appendix B, “TCP/IP Settings Problems,” to troubleshoot the  
problem.  
2-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NI WAP-3701/3711 User’s Manual  
Web Console Configuration  
Overview  
Menu Structure  
The left side of the home page contains a menu that you can use to carry out commands. Here is a  
brief description of the hyperlinks in the menu:  
y
y
Home. For returning to the home page.  
Status. Status information.  
¾
¾
¾
¾
Wireless Clients. The status of the wireless clients currently associated with the AP.  
DHCP Mappings. Current IP-MAC address mappings of the built-in DHCP server.  
System Log. System events log.  
Link Monitor. When the NI WAP-3701/3711 is in AP Client mode, this page shows the  
signal strength and link quality of the wireless link to its associated access point.  
y
General. Global operations.  
¾
Operational Mode. Operational mode of the NI WAP-3701/3711—AP/Bridge or AP  
Client.  
¾
¾
Password. For changing the settings of the NI WAP-3701/3711.  
Firmware Tools. For upgrading the firmware of the NI WAP-3701/3711, backing up and  
restoring the configuration, and resetting the NI WAP-3701/3711’s configuration to  
factory defaults.  
y
y
TCP/IP. TCP/IP-related settings.  
¾
¾
Addressing. IP address settings for the AP to work with TCP/IP.  
DHCP Server. Settings for the DHCP (Dynamic Host Configuration Protocol) server on  
the Access Point.  
IEEE 802.11. IEEE 802.11g-related settings.  
¾
Communication. Basic settings for the IEEE 802.11g interface of the NI  
WAP-3701/3711 to work properly with wireless clients.  
¾
¾
Security. Security settings for authenticating wireless users and encrypting wireless data.  
IEEE 802.1X/RADIUS. IEEE 802.1X Port-Based Network Access Control and RADIUS  
(Remote Authentication Dial-In User Service) settings for better wireless security.  
y
Advanced. Advanced settings of the NI WAP-3701/3711.  
¾
Packet Filters. Ethernet Type Fiters, IP Protocol Filters, and TCP/UDP Port Filters  
settings.  
¾
Management. UPnP, System Log, and SNMP settings.  
3-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
NI WAP-3701/3711 User’s Manual  
Web Console Configuration  
Save, Save & Restart, and Cancel Buttons  
There are three buttons at the bottom of each page for configuring settings—Save, Save &  
Restart, and Cancel. Clicking Save stores changes to the NI WAP-3701/3711’s memory and  
returns you to the home page. Clicking Save & Restart stores the changes to the NI  
WAP-3701/3711’s memory and restarts the NI WAP-3701/3711 to activate the new settings.  
Clicking Cancel discards any changes already made and returns you to the home page.  
Note that if you click on Save, the home page will reflect the fact that the configuration settings  
have been changed by displaying two buttons—Restart and Cancel. In addition, changes are  
highlighted in red. Clicking Restart restarts the AP to activate the new settings. Clicking Cancel  
discards all of the changes.  
Home and Refresh Buttons  
At the bottom of each status page that shows read-only information, there are two buttons—Home  
and Refresh. Clicking Home brings you back to the home page. Clicking Refresh updates the  
status information showing on the page.  
Viewing Status  
Associated Wireless Clients  
On this page, the status information of each associated client, including its MAC address, IP  
address, user name (if the client has been IEEE 802.1X authenticated), number of bytes it has sent,  
number of bytes it has received, and the time of its last activity, is shown.  
3-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
NI WAP-3701/3711 User’s Manual  
Web Console Configuration  
Current DHCP Mappings  
On this page, all the current static or dynamic DHCP mappings are shown. A DHCP mapping is a  
correspondence relationship between an IP address assigned by the DHCP server and a computer  
or device that obtains the IP address. A computer or device that acts as a DHCP client is identified  
by its MAC address.  
A static mapping indicates that the DHCP client always obtains the specified IP address from the  
DHCP server. You can set static DHCP mappings in the Static DHCP Mappings section of the  
DHCP Server configuration page. A dynamic mapping indicates that the DHCP server chooses an  
IP address from the IP address pool specified by the First allocateable IP address and  
allocateable IP address count settings on the DHCP Server configuration page.  
System Log  
System events are recorded in the memory of the NI WAP-3701/3711. The logged information is  
useful for troubleshooting purposes. The system events are divided into several categories, and  
you can select which categories of events to log.  
Link Monitor (AP Client mode only)  
When the NI WAP-3701/3711 is in AP Client mode, you can use the Link Monitor status page to  
monitor the link quality and signal strength sensed by its RF module. Larger values mean better  
wireless connectivity to the associated Access Point. This feature is especially useful when you are  
aligning a pair of directional antennas for bridging applications.  
The values are updated every 20 seconds.  
NOTE  
3-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
NI WAP-3701/3711 User’s Manual  
Web Console Configuration  
General Operations  
Specifying the Operational Mode  
Go to the General, Operational Mode section, select an operational mode and then click Save at  
the bottom of this page. This will take you back to the starting page.  
The AP supports 2 operational modes:  
y
y
AP/Bridge.  
This mode provides both Access Point and Static LAN-to-LAN Bridging functionality.  
The static LAN-to-LAN bridging function is supported through Wireless Distribution System  
(WDS).  
AP Client.  
This mode is for Dynamic LAN-to-LAN Bridging. The AP Client automatically establishes  
bridge links with APs from any vendor.  
In either mode, the NI WAP-3701/3711 forwards packets between its Ethernet interface and  
wireless interface for wired hosts on the Ethernet side and wireless host(s) on the wireless side.  
There are 2 types of wireless links as specified by the IEEE 802.11 standard.  
y
STA-AP.  
This type of wireless link is established between an IEEE 802.11 Station (STA) and an IEEE  
802.11 Access Point (AP). An STA is usually a client computer (PC or PDA) with a WLAN  
network interface card (NIC). The AP Client mode is actually an STA.  
y
WDS.  
This type of wireless link is established between two IEEE 802.11 APs. Wireless packets  
transmitted along the WDS link comply with the IEEE 802.11 WDS (Wireless Distribution  
System) format at the link layer.  
The relationships among the operational modes and the wireless link types are shown in the  
following table:  
AP/Bridge  
WDS  
AP Client  
AP/Bridge  
AP Client  
STA-AP  
STA-AP  
To establish a static bridge link based on WDS, the AP/bridges at both end of the WDS link must  
be configured manually with each other’s MAC addresses. To establish a dynamic bridge link  
between an AP and an AP Client, both devices must be configured with the same SSID and WEP  
settings. The AP Client automatically scans for any AP that is using the matched SSID and  
establishes a bridge link with the scanned AP.  
3-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
NI WAP-3701/3711 User’s Manual  
Web Console Configuration  
Although it is more convenient to use dynamic bridging, there is a limitation—the AP Client can  
only transmit TCP/IP packets between its wireless interface and Ethernet interface; other types of  
traffic (such as IPX and AppleTalk) are not forwarded.  
NOTE  
TIP  
When the AP is configured for AP Client, it can be used as an Ethernet-to-wireless network  
adapter. For example, a notebook computer equipped with an Ethernet adapter, but no wireless  
card, can be connected to this device with an Ethernet cable for wireless connectivity to another  
access point.  
Administrative Password  
On this page, you can change the user name and password. The new password must be typed twice  
to confirm (note that the default user Name and Password or “admin” and “root,” respectively).  
Managing the Firmware  
Firmware management operations for the NI WAP-3701/3711 include “Firmware Upgrade,”  
“Configuration Backup,” “Configuration Restore,” and “Configuration Reset (Factory Defaults).”  
Firmware upgrade, configuration backup, and configuration restore can be achieved via HTTP or  
TFTP. The HTTP-based method is suggested because it is more user friendly. However, due to the  
fact that different Web browsers and versions behave differently, HTTP-based firmware  
management operations may not work properly with some Web browsers. If you cannot  
successfully perform HTTP-based firmware management operations with your Web browser, try  
the TFTP-based method.  
Upgrading the Firmware by HTTP  
To upgrade the firmware of NI WAP-3701/3711 by HTTP:  
1. Click Browse and then select a correct firmware .bin file. The firmware file path will be  
shown in the Firmware file name text box.  
2. Click Upgrade to begin the upgrade process.  
3-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
NI WAP-3701/3711 User’s Manual  
Web Console Configuration  
Backing up and Restoring Configuration Settings by HTTP  
To back up the configuration of the NI WAP-3701/3711 by HTTP (i.e., export the configuration to  
a file):  
1. Click on Back Up  
2. You will be prompted to open or save the configuration file. Click on Save.  
3. The configuration file is named with the NI WAP-3701/3711’s MAC address. For example, if  
the NI WAP-3701/3711’s MAC address is 00-01-02-33-44-55, the configuration backup file  
should be “000102334455.hex”. Don’t change the configuration file name in the Save As  
dialog box. Select the folder in which the configuration file is to be stored, and then click on  
Save.  
The procedure may be different for different Web browsers (IE, Netscape, etc.).  
NOTE  
To restore the configuration of the NI WAP-3701/3711 by HTTP (i.e., import the configuration  
from a file):  
1. Click Browse and then select the correct configuration .hex file. You must make sure the file  
name is the NI WAP-3701/3711’s MAC address. The firmware file path will be shown in the  
Firmware file name text box.  
2. Click Restore to upload the configuration file to the NI WAP-3701/3711.  
Upgrading Firmware by TFTP  
When using TFTP as the firmware management protocol, you can configure settings for the AP’s  
TFTP client to communicate with a TFTP server. If the TFTP client does not get a response from  
the TFTP server within a period specified by the Timeout setting, it will resend the previous  
request. The Max number of retries setting specifies the maximum number of resends before the  
TFTP client stops communicating with the TFTP server.  
To upgrade the NI WAP-3701/3711’s firmware by TFTP:  
1. Prepare a computer that will be used as a TFTP server and as a managing computer to trigger  
the upgrade process.  
2. Connect the computer and one of the LAN Ethernet switch port with a normal Ethernet cable.  
3. Configure the IP address of the computer so that the NI WAP-3701/3711 and the computer  
are on the same IP subnet.  
3-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NI WAP-3701/3711 User’s Manual  
Web Console Configuration  
4. On the computer, run the TFTP Server utility, and specify the folder in which the firmware  
files will be placed.  
5. On the computer, run a Web browser and click the General, Firmware Tools hyperlink.  
6. Choose TFTP as the Firmware management protocol.  
7. Specify the IP address of the computer, which acts as a TFTP server. If you don’t know the IP  
address of the computer, open a Command Prompt, and type ipconfig, then press the Enter  
key.  
8. Trigger the firmware upgrade process by clicking Upgrade.  
After the dialog box of the TFTP server program appears, be sure to specify the working folder  
within which the downloaded firmware files reside.  
NOTE  
Make sure the Accept read requests check box of the TFTP Server is selected.  
The LAN IP address of the AP and the IP address of the TFTP server must be on the same IP  
subnet for TFTP to work.  
Due to the unreliable nature of wireless media, it is highly recommended that the TFTP server  
and the wireless AP that is being upgraded are connected by Ethernet on the same LAN. Doing so  
will help ensure a much smoother upgrade process.  
After the firmware is upgraded, be sure to delete the contents of the Web browser cache so that  
the Web management pages can be shown correctly.  
A failed upgrade may corrupt the firmware and cause the NI WAP-3701/3711 to fail. When this  
occurs, contact NI technical support for assistance.  
If you want to upgrade the firmware of a deployed AP from a remote location over the Internet,  
adjust the Timeout and Max no. of retries settings of the TFTP Server for remote TFTP upgrade  
to succeed.  
TIP  
3-8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NI WAP-3701/3711 User’s Manual  
Web Console Configuration  
Backing up and Restoring Configuration Settings by TFTP  
To back up the configuration of the NI WAP-3701/3711 by TFTP:  
1. Prepare a computer that will be used as a TFTP server and as a managing computer to trigger  
the backup process.  
2. Connect the computer and one of the LAN Ethernet switch ports with a normal Ethernet cable.  
3. Configure the IP address of the computer so that the computer and the NI WAP-3701/3711  
are on the same IP sub-net.  
4. On the computer, run the TFTP Server utility. Select the Accept write requests check box,  
and specify the folder to which the configuration settings of the AP will be saved.  
5. On the computer, run a Web browser and click the General, Firmware Tools hyperlink.  
6. Choose TFTP as the Firmware management protocol.  
7. Within the Configuration Backup/Restore section, specify the IP address of the computer  
that acts as a TFTP server. If you don’t know the IP address of the computer, open a  
Command Prompt, and type ipconfig, then press the Enter key.  
8. Trigger the backup process by clicking Back Up. The NI WAP-3701/3711’s configuration  
settings will be saved as “AaBbCcDdEeFf.hex” by the TFTP server, where  
“AaBbCcDdEeFf” is the NI WAP-3701/3711’s MAC address. For example, if the NI  
WAP-3701/3711’s MAC address is 00-01-02-33-44-55, the configuration backup file will be  
“000102334455.hex”.  
Remember to select the Accept write requests check box of TFTP Server.  
NOTE  
To restore the configuration of the NI WAP-3701/3711 by TFTP:  
1. Prepare a computer that will be used as a TFTP server and as a managing computer to trigger  
the restoring process.  
2. Connect the computer and one of the LAN Ethernet switch ports with a normal Ethernet cable.  
3. Configure the IP address of the computer so that the computer and the NI WAP-3701/3711  
are on the same IP subnet.  
4. On the computer, run the TFTP Server utility, and specify the folder in which the  
configuration backup file resides. A configuration backup file is named with the NI  
WAP-3701/3711’s MAC address. For example, if the NI WAP-3701/3711’s MAC address is  
00-01-02-33-44-55, the configuration backup file should be “000102334455.hex”.  
5. On the computer, open the web browser and click the General, Firmware Tools hyperlink.  
6. Choose TFTP as the Firmware management protocol.  
7. In the Configuration Backup/Restore section, specify the IP address of the computer that  
acts as a TFTP server. If you don’t know the IP address of the computer, open a Command  
Prompt, type ipconfig, and then press the Enter key.  
8. Trigger the restoring process by clicking Restore. The NI WAP-3701/3711 will then  
download the configuration backup file from the TFTP server.  
Make sure the file is a valid configuration backup file for NI WAP-3701/3711.  
NOTE  
3-9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NI WAP-3701/3711 User’s Manual  
Web Console Configuration  
If you want to back up or restore the configuration from a remote location over the Internet,  
adjust the Timeout and Max no. of retries settings of TFTP Server for remote TFTP  
configuration backup/restore to succeed.  
TIP  
Resetting the Configuration to Factory Defaults  
Clicking the Reset button resets the device configuration to factory defaults.  
WARNING  
Think twice before clicking the Reset button. Doing so will cause you to lose all of your current  
configuration settings.  
Configuring TCP/IP-related Settings  
Addressing  
The IP address of the AP can be set manually (Set Manually) or automatically assigned by a  
DHCP server on the LAN (Obtain from a DHCP Server). If you are manually setting the IP  
address, Subnet mask, and Default gateway settings, set them appropriately, so that they comply  
with your LAN environment. In addition, you can specify the Host name and Domain (DNS  
suffix) of the NI WAP-3701/3711.  
3-10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
NI WAP-3701/3711 User’s Manual  
Web Console Configuration  
DHCP Server (AP/Bridge modes only)  
Basic  
The NI WAP-3701/3711 can assign IP addresses to client computers automatically by DHCP. In  
this section of the management page, you can specify the Default gateway, Subnet mask,  
Primary DNS server, and Secondary DNS server settings that will be sent to a client at its  
request. Additionally, you can specify the first IP address that will be assigned to the clients and  
the number of IP addresses that can be allocated.  
There should only be one DHCP server on the LAN; otherwise, DHCP will not work properly. If  
a DHCP server is already connected to the LAN, disable the DHCP server functionality of the NI  
WAP-3701/3711.  
NOTE  
By default, the DHCP server function is disabled.  
Static DHCP Mappings  
IP addresses of servers are often static so that clients can always locate the servers by the static IP  
addresses. By using Static DHCP Mappings, you can ensure that a host will get the same IP  
address when it requests one from the DHCP server. Therefore, instead of configuring the IP  
address of an intranet server manually, you can configure the server to obtain an IP address by  
DHCP so that it is always assigned the same IP address.  
3-11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
NI WAP-3701/3711 User’s Manual  
To assign a static IP address to a specific DHCP client:  
Web Console Configuration  
1. Specify the MAC address of the DHCP client and the IP address to be assigned to it. Then,  
give a description for this mapping.  
2. Select the corresponding Enabled check box.  
Configuring IEEE 802.11g-related Settings  
Communication  
Basic  
Basic IEEE 802.11g-related communication settings include AP functionality, RF type,  
Regulatory domain, Channel number, Network name (SSID), Data rate, and Transmit  
power.  
For specific needs such as configuring the NI WAP-3701/3711 as a wireless LAN-to-LAN bridge,  
the AP functionality can be disabled so that no wireless client can associate with the AP.  
The RF type of the WLAN interface can be configured to work with IEEE 802.11b only (B Only),  
IEEE 802.11g only (G Only), B WIFI mode (for internal usage), or mixed mode (Mixed—802.11g  
and 802.11b simultaneously).  
The number of available RF channels depends on local regulations; therefore, you must choose an  
appropriate regulatory domain to comply with local regulations. The SSID of a wireless client  
computer and the SSID of the AP must be identical for them to communicate with each other.  
If you experience RF interference, you may want to reduce the Data rate to ensure a more reliable  
wireless transmission. In most cases, leave the setting at Auto.  
The transmit power of the RF module on the NI WAP-3701/3711 can be adjusted so that the RF  
coverage of the NI WAP-3701/3711 can be changed.  
Link Integrity  
When the Ethernet LAN interface has been detected as being disconnected from the wired network,  
all currently associated wireless clients are disassociated by the AP and no wireless client can  
associate with the AP. The detection mechanism is based on pinging the IP address specified in the  
Reference host.  
3-12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
NI WAP-3701/3711 User’s Manual  
Web Console Configuration  
Association Control  
If the number of currently associated wireless clients exceeds the value specified in the Max  
number of clients setting, no more wireless clients can associate with the NI WAP-3701/3711. If  
the traffic load of the NI WAP-3701/3711 exceeds the load specified in the Block clients if traffic  
load exceeds setting, no more wireless clients can associate with the NI WAP-3701/3711.  
AP Load Balancing  
Several APs can form a load-balancing group if they are set with the same Group ID. The  
load-balancing policy can be by Number of Users or by Traffic Load.  
If the by-number-of-users policy is selected, a new wireless user can only associate with an AP  
that has the smallest number of associated wireless users in the group. On the other hand, if the  
by-traffic-load policy is selected, a new wireless user can only associate with an AP that has the  
least traffic load in the group.  
Wireless Distribution System  
Notebook  
Computer  
WDS  
LAN  
AP 2  
AP 1  
Traditionally, access points are connected by Ethernet. By using a Wireless Distribution System  
(WDS), APs can communicate with one another wirelessly. For example, AP 2 acts as an access  
point for the notebook computers and it forwards packets sent from the notebook computers to AP  
1 through WDS. Then, AP 1 forwards the packets to the Ethernet LAN. Packets destined for the  
notebook computers follow a reverse path from the Ethernet LAN through the APs to the notebook  
computers. In this way, AP 2 plays a role of “AP repeater.”  
WDS Link  
LAN  
Segment 2  
LAN  
Segment 1  
Bridge 1  
Bridge 2  
3-13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NI WAP-3701/3711 User’s Manual  
Web Console Configuration  
By WDS, two or more LAN segments can be connected wirelessly. As illustrated in the above  
figure, a pair of wireless LAN-to-LAN bridges is used to connect two LAN segments. Since the  
AP is WDS-enabled, it can be used as a wireless bridge.  
The NI WAP-3701/3711 can have up to 6 WDS links to other APs or wireless bridges.  
NOTE  
To enable a WDS link:  
1. Specify the MAC address of the NI WAP-3701/3711 at the other end of the WDS link.  
2. Select the corresponding Enabled check box.  
For example, assume that you want two NI WAP-3701/3711’s with MAC addresses  
00-02-65-01-62-C5 and 00-02-65-01-62-C6 to establish a WDS link. On the NI WAP-3701/3711  
with MAC address 00-02-65-01-62-C5, set the peer MAC address of port 1 to 00-02-65-01-62-C6  
and on the NI WAP-3701/3711 with MAC address 00-02-65-01-62-C6, set the peer MAC address  
of port 1 to 00-02-65-01-C5.  
Plan your wireless network and draw a diagram so that you know how each NI WAP-3701/3711  
is connected to other peer APs or wireless bridges by WDS, and how bridges are connected to  
other peer bridges by WDS. See the following figure for an sample network-planning diagram.  
TIP  
Sample wireless bridge network topology.  
3-14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NI WAP-3701/3711 User’s Manual  
Web Console Configuration  
WARNING  
Be sure to eliminate loops from networks that consist of wireless bridges, Ethernet switches,  
Ethernet links, and WDS links. If any loops exist, packets will circle around the loops and  
network performance will be seriously degraded.  
Network topology containing a loop  
Security  
IEEE 802.11g security settings include SSID broadcasts, Wireless client isolation, Security  
mode, IEEE 802.11 Authentication algorithm, WEP keys, MAC-Address-Based Access  
Control.  
Basic  
For security reasons, it is highly recommended that you do not set the security mode to the Open  
System option. When the security mode is set to Open System, no authentication or data  
encryption will be performed. In addition, you can disable the SSID broadcast functionality so that  
a wireless client computer with an SSID set to “any” cannot associate with the NI  
WAP-3701/3711.  
When the Wireless client isolation setting is set to This AP Only, wireless clients of this AP  
cannot see each other, and wireless-to-wireless traffic is blocked. When the setting is set to All  
APs in this Subnet, traffic between wireless users from different APs on the same IP subnet is  
blocked. This feature is useful for WLANs deployed in public places. In this way, hackers have no  
chance to attack other wireless users in a hotspot. The behaviors are illustrated in the following  
figures.  
3-15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
NI WAP-3701/3711 User’s Manual  
Web Console Configuration  
STA 1  
STA 3  
STA 2  
AP 1  
AP 2  
WCI:  
WCI:  
This AP Only  
This AP Only  
Switch  
Wireless Link  
Ethernet Link  
Behavior of the “This AP Only” wireless client isolation option  
STA 1  
STA 3  
STA 2  
AP 1  
AP 2  
WCI:  
All APs in This  
Subnet  
WCI:  
All APs in This  
Subnet  
Switch  
Wireless Link  
Ethernet Link  
Behavior of the “All APs on This Subnet” wireless client isolation option  
When AP 1 and AP 2 are using the “This AP Only” option, wireless traffic between STA 1 and  
STA 2 is blocked by AP 1, whereas wireless traffic between STA 2 and STA 3 (which are  
associated with different APs) is still allowed. If the “All APs in This Subnet” option is used as  
shown in the above figure, AP 1 and AP 2 communicate with each other via an inter-AP protocol  
to share their STA association information to block wireless traffic among all the STAs.  
3-16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NI WAP-3701/3711 User’s Manual  
Web Console Configuration  
A total of 7 security modes are available with the different NI WAP-3701/3711 models:  
y
y
y
Open System. No authentication, no data encryption.  
Static WEP. WEP (Wired Equivalent Privacy) keys must be configured manually.  
Static TKIP (WPA-PSK). Only TKIP (Temporal Key Integrity Protocol) mechanism of WPA  
(Wi-Fi Protected Access) is enabled. In this mode, you need to specify the Pre-shared key,  
which will be used by the TKIP engine as a master key to generate keys that actually encrypt  
outgoing packets and decrypt incoming packets.  
The number of characters of the Pre-shared key setting must be at least 8 and can be up to 63.  
NOTE  
y
y
y
y
IEEE 802.1X EAP without Encryption (EAP-MD5). The IEEE 802.1X functionality is  
enabled and the user-name/password-based EAP-MD5 authentication is used. No data  
encryption.  
IEEE 802.1X EAP with Static WEP (EAP-MD5). The IEEE 802.1X functionality is enabled  
and the user-name/password-based EAP-MD5 authentication is used. Data encryption is  
achieved by static WEP.  
IEEE 802.1X EAP with Dynamic WEP (EAP-TLS, EAP-TTLS, PEAP). The IEEE 802.1X  
functionality is enabled and dynamic WEP key distribution authentication (EAP-TLS,  
EAP-TTLS, or PEAP) is used. Data encryption is achieved by dynamic WEP.  
IEEE 802.1X EAP with Dynamic TKIP (WPA). This is a full WPA mode, in which both the  
TKIP and IEEE 802.1X dynamic key exchange mechanisms are enabled. The AP is highly  
secure in this mode.  
In the above security modes, a back-end RADIUS (Remote Authentication Dial-In User Service)  
server is needed if IEEE 802.1X functionality is enabled. See the appropriate section for more  
information about IEEE 802.1X and RADIUS.  
According to the IEEE 802.11 standard, WEP can be used for authentication and data encryption.  
Normally, Shared Key authentication is used if WEP data encryption is enabled. In rare cases,  
Open System authentication may be used when WEP data encryption is enabled. The  
Authentication algorithm setting is provided for better compatibility with wireless clients with  
various WLAN network adapters. There are three options available, including Open System,  
Shared Key, and Auto.  
When WEP is enabled by a security mode, the Key length can be specified to be 64 Bits or 128  
Bits. The Selected key setting specifies the key to be used as a send-key for encrypting traffic  
from the AP side to the wireless client side. All 4 WEP keys are used as receive-keys to decrypt  
traffic from the wireless client side to the AP side.  
Each field of a WEP key setting is a hex-decimal number from 00 to FF. For example, when the  
security mode is Static WEP and the key length is 64 Bits, you could set Key 1 to  
“00012E3ADF”.  
NOTE  
3-17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NI WAP-3701/3711 User’s Manual  
Web Console Configuration  
MAC-Address-Based Access Control  
With MAC-Address-Based Access Control, you can specify the wireless client computers that  
are permitted or not permitted to associate with the NI WAP-3701/3711. When the table type is set  
to inclusive, entries in the table are permitted to associate with the NI WAP-3701/3711. When the  
table type is set to exclusive, entries in the table are not permitted to associate with the NI  
WAP-3701/3711.  
To deny access for wireless clients to the wireless network:  
1. Select Enabled from the Functionality drop-down list.  
2. Set the Access control type to exclusive.  
3. Specify the MAC address of a wireless client to be denied access, and then click Add.  
4. Repeat Steps 3 for other wireless clients.  
To grant access for wireless clients to the wireless network:  
1. Select Enabled from the Functionality drop-down list.  
2. Set the Access control type to inclusive.  
3. Specify the MAC address of a wireless client to be denied access, and then click Add.  
4. Repeat Steps 3 for other wireless clients.  
To delete an entry in the access control table:  
y
Click Delete next to the entry.  
The size of the access control table is 64.  
NOTE  
Instead of manually entering MAC addresses to the access control table one by one, you can  
prepare a text file that contains all the MAC addresses and put it on a TFTP server, and then  
command the NI WAP-3701/3711 to download the MAC ACL (Access Control List) file from the  
TFTP server. The following figure shows the contents of a sample ACL file.  
3-18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NI WAP-3701/3711 User’s Manual  
Web Console Configuration  
Sample MAC ACL file  
To download a MAC ACL file from a TFTP server:  
1. Specify the IP address of the TFTP server in the TFTP server IP address text box.  
2. Specify the name of the MAC ACL file on the TFTP server in the MAC ACL file name text  
box.  
3. Click Download.  
IEEE 802.1X/RADIUS (AP mode only)  
IEEE 802.1X Port-Based Network Access Control is a new standard for solving some security  
issues associated with IEEE 802.11, such as lack of user-based authentication and dynamic  
encryption key distribution. With IEEE 802.1X and the help of a RADIUS (Remote  
Authentication Dial-In User Service) server and a user account database, an enterprise or ISP  
(Internet Service Provider) can manage its mobile users’ access to its wireless LANs. Before being  
granted access to a wireless LAN supporting IEEE 802.1X, a user needs to issue his or her user  
name and password or digital certificate to the backend RADIUS server by EAPOL (Extensible  
Authentication Protocol Over LAN). The RADIUS server can record accounting information, such  
as when a user logs on to the wireless LAN and logs off from the wireless LAN for monitoring or  
billing purposes.  
The IEEE 802.1X functionality of the access point is controlled by the security mode. So far, the  
wireless access point supports two authentication mechanisms—EAP-MD5 (Message Digest  
version 5), EAP-TLS (Transport Layer Security). If EAP-MD5 is used, the user must give his or  
her user name and password for authentication. If EAP-TLS is used, the wireless client computer  
automatically gives the user’s digital certificate that is stored in the computer hard disk or a smart  
card for authentication. And after a successful EAP-TLS authentication, a session key is generated  
automatically for encrypting wireless packets sent between the wireless client computer and the  
associated wireless access point. In short, EAP-MD5 only supports user authentication, whereas  
EAP-TLS supports both user authentication and dynamic encryption key distribution.  
3-19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
NI WAP-3701/3711 User’s Manual  
Web Console Configuration  
IEEE 802.1X-Compliant  
Wireless Client  
Wireless AP  
user authentication  
Internet  
Wireless AP  
RADIUS  
Server  
User  
Database  
user authentication  
IEEE 802.1X and RADIUS  
An access point supporting IEEE 802.1X can be configured to communicate with two RADIUS  
servers. When the primary RADIUS server fails to respond, the wireless access point will try to  
communicate with the secondary RADIUS server. You can specify the length of timeout and the  
number of retries before communicating with the secondary RADIUS server after failing to  
communicate with the primary RADIUS server.  
An IEEE 802.1X-capable wireless access point and its RADIUS server(s) share a secret key so  
that they can authenticate each other. In addition to its IP address, a wireless access point can  
identify itself by an NAS (Network Access Server) identifier. Each IEEE 802.1X-capable wireless  
access point must have a unique NAS identifier.  
3-20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NI WAP-3701/3711 User’s Manual  
Web Console Configuration  
Configuring Advanced Settings  
Packet Filters  
The NI WAP-3701/3711 provides layer 2 (Ethernet Type Filters), layer 3 (IP Protocol Filters), and  
layer 4 (TCP/UDP Port Filters) filtering capabilities. The configuration processes for the filters are  
similar.  
y
y
y
Functionality: whether this filtering capability is enabled or disabled.  
Policy for matched packets: how a matched packet is processed—discard or pass.  
To enable a filtering rule: select the check box to the left of the rule.  
Ethernet Type Filters  
The Ethernet type field of the MAC (Media Access Control) header of a packet incoming from the  
WLAN or Ethernet interface is inspected for filtering. As a rule, specify the hex-decimal Ethernet  
type number and give the rule a name.  
IP Protocol Filters  
The protocol, source address, and destination address fields of a packet incoming from the WLAN  
or Ethernet interface is inspected for filtering. As a rule, specify the hex-decimal protocol number,  
source IP address range (Source IP Address AND Source Subnet Mask), and destination IP  
address range (Destination IP Address AND Destination Subnet Mask).  
A source/destination IP address range is determined by performing an AND operation on the  
source/destination IP address field and the source/destination subnet mask field. For example, if  
the source IP address field is 192.168.127.253 and the source subnet mask field is 255.255.255.0,  
the resultant source IP address range is 192.168.127.0 to 192.168.127.255.  
3-21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
NI WAP-3701/3711 User’s Manual  
Web Console Configuration  
TCP/UDP Port Filters  
The destination port field of the TCP or UDP header of a packet incoming from the WLAN or  
Ethernet interface is inspected for filtering. As a rule, specify the decimal Destination Port,  
Protocol type (TCP/UDP), and the name of the higher-level protocol (Application Name).  
Management  
UPnP  
UPnP (Universal Plug and Play) enables a Windows XP user to discover peripheral devices  
automatically by HTTP. When the UPnP functionality is enabled, you can see the AP in My  
Network Places of Windows XP. The NI WAP-3701/3711 can be given a friend name that will be  
shown in My Network Places. Double-clicking the icon in My Network Places that stands for the  
AP will launch the default Web browser for you to configure the NI WAP-3701/3711.  
System Log  
System events can be logged to the on-board RAM of the NI WAP-3701/3711 (Local log) or sent  
to a remote computer on which an SNMP trap monitor program runs (Remote log by SNMP trap).  
See the next subsection for more information about SNMP trap settings.  
The system events are divided into the following categories:  
y
y
y
y
General: system and network connectivity status changes.  
Built-in AP: wireless client association and WEP authentication status changes.  
MIB II traps: Cold Start, Warm Start, Link Up, Link Down and SNMP Authentication Failure.  
RADIUS user authentication: RADIUS user authentication status changes.  
3-22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
NI WAP-3701/3711 User’s Manual  
Web Console Configuration  
The SNMP Authentication Failure trap is issued when using an incorrect community string to  
manage the AP via SNMP and the SNMP MIB II OID, snmpEnableAuthenTraps, is enabled  
(disabled by default).  
NOTE  
SNMP  
The SNMP (Simple Network Management Protocol) functionality can be disabled, and you can  
specify the name (used as a password) of the read-only and read-write community. In addition, up  
to 5 SNMP trap targets can be set in the SNMP Trap Table.  
To specify a trap target :  
1. Type the IP address of the target host.  
2. Type the Community for the host.  
Select the corresponding check box next to the IP address text box.  
3-23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
A
Appendix  
A
Default Settings  
Press the Reset (SF-Reset, or Soft-Reset) switch on the housing of a powered-on AP to reset the  
configuration settings to factory-default values.  
TIP  
Setting Name  
Default Value  
Global  
User Name  
Password  
IEEE 802.11g  
Regulatory Domain  
admin  
root  
FCC (U.S.) or ETSI (Europe)  
Channel Number  
SSID  
11 for FCC or 13 for ETSI  
NI  
SSID Broadcasts  
Transmission Rate  
Transmit Power  
Enabled  
Auto  
100%  
MAC Address  
See the label on the accompanying PCMCIA card  
or the label on the housing of the NI  
WAP-3701/3711.  
Security Mode  
Selected WEP Key  
Open System  
Key #1  
WEP Key #1  
WEP Key #2  
00-00-00-00-00  
00-00-00-00-00  
00-00-00-00-00  
00-00-00-00-00  
Disabled  
WEP Key #3  
WEP Key #4  
MAC-Address-Based Access Control  
Access Control Table Type  
Wireless Client Isolation  
AP Load balancing  
Link Integrity  
Inclusive  
Disabled  
Disabled  
Disabled  
Association Control  
Max Number of Clients  
64  
Block Clients if Traffic Load Exceeds Disabled  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
NI WAP-3701/3711 User’s Manual  
Default Settings  
LAN Interface  
Method of obtaining an IP Address  
Set manually  
192.168.127.253  
255.255.255.0  
0.0.0.0  
IP Address  
Subnet Mask  
Default Gateway  
DHCP Server  
Disabled  
Management  
UPnP  
Enabled  
Local Log  
Enabled  
public  
System Log  
SNMP  
SNMP read community  
SNMP write community  
TELNET  
private  
Enabled  
A-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
B
Appendix  
B
Troubleshooting  
Check the following first:  
y
Make sure that the power is on and the Ethernet cables are connected firmly to the RJ45 jacks  
of the NI WAP-3701/3711.  
y
y
Make sure the LED WLAN of the AP is blinking to indicate that the RF is working.  
Make sure you are using the correct types of Ethernet cables. Keep in mind that there are two  
kind of Ethernet cable—normal and crossover.  
Wireless Settings Problems  
The wireless client computer cannot associate with an NI WAP-3701/3711.  
y
y
y
Is the wireless client set in infrastructure mode?  
Check the operating mode of the WLAN NIC.  
Is the SSID of the WLAN NIC identical to that of the prospective NI WAP-3701/3711?  
Check the SSID setting of the WLAN NIC and of the NI WAP-3701/3711.  
Is the WEP functionality of the prospective NI WAP-3701/3711 enabled?  
¾
¾
¾
Make appropriate WEP settings of the client computer to match those of the NI  
WAP-3701/3711.  
y
Is the prospective NI WAP-3701/3711 within range of wireless communication?  
¾
Check the signal strength and link quality sensed by the WLAN NIC.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
NI WAP-3701/3711 User’s Manual  
Troubleshooting  
TCP/IP Settings Problems  
Correspondent  
Host  
IEEE 802.11g  
Internet  
Ethernet LAN  
Stage A  
State B  
Stage D  
Client  
AP  
Default Gateway  
DNS Server  
Computer  
of Client Computer of Client Computer  
Communication stages for a client to reach its correspondent host  
For a wireless client computer to communicate with a host on the Internet by the host’s domain  
name (e.g., http://www.wi-fi.com), it first sends a DNS request to a DNS server on the Internet.  
The DNS request travels first to the AP, and then the AP relays this request to the default gateway  
of the client computer. Finally, this request is forwarded by the gateway to the DNS server on the  
Internet. The DNS reply issued by the DNS server is transmitted back to the client computer  
following a reverse path. When the client computer receives the DNS reply, it knows the IP  
address of the correspondent host and sends additional packets to this IP address.  
As illustrated in the above figure, the communication path could be broken at some of the stages.  
The OS-provided network diagnostic tool, ping.exe, can be employed to determine TCP/IP-related  
communication problems.  
If two or more NICs are installed and operating on a client computer, TCP/IP may not work  
properly due to incorrect entries in the routing table. Use the OS-provided command-line network  
tool, route.exe, to add or delete entries from the routing table. Or, use Windows-provided Device  
Manager to disable unnecessary NICs.  
NOTE  
Solve the following problems in order:  
The AP does not respond to ping from the client computer.  
y
Are two or more NICs installed on the client computer?  
¾
Use the OS-provided command-line network tool, route.exe, to modify the contents of  
the routing table.  
¾
Use Windows-provided Device Manager to disable unnecessary NICs.  
y
Is the underlying link (Ethernet or IEEE 802.11g) established?  
¾
Make sure the Ethernet link is OK.  
B-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
NI WAP-3701/3711 User’s Manual  
Troubleshooting  
¾
Make sure the wireless settings of the wireless client computer and of the AP match.  
y
Are the IP address of the client computer and the IP address of the AP on the same IP subnet?  
¾
Use WinIPCfg.exe or IPConfig.exe to see the current IP address of the client computer.  
Make sure the IP address of the client computer and the IP address of the AP are on the  
same IP subnet.  
If you forget the current IP address of the AP, use a Wireless Router/AP Browser combination to  
get the information (see Appendix B-3).  
TIP  
The default gateway of the client computer does not respond to ping from the client  
computer.  
y
y
y
Solve the preceding problem first.  
Are the IP address of the AP and the IP address of the client computer on the same IP subnet?  
If you cannot locate any incorrect AP settings, the default gateway may be down, or there are  
other communication problems on the network backbone.  
The DNS server(s) of the client computer do not respond to ping from the client computer.  
y
y
Solve the preceding problems first.  
If you cannot locate any incorrect AP settings, the default gateway of the AP may be down, or  
there are other communication problems on the network backbone.  
Unknown Problems  
The AP has been set to obtain an IP address automatically by DHCP. How can I determine  
the acquired IP address so that I can manage it using a Web browser?  
y
Use the utility, Wireless Router/AP Browser (WLBrwsr.exe), in the “Utilities” folder on the  
companion CD-ROM disc. This utility can discover nearby APs and show their MAC  
addresses and IP addresses. In addition, it can launch the default Web browser on your  
computer.  
Wireless Router/AP Browser  
B-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
NI WAP-3701/3711 User’s Manual  
Troubleshooting  
The NI WAP-3701/3711 stops working and does not respond to Web management requests.  
y
y
The firmware of the AP may be stuck in an incorrect state.  
¾
Unplug the power connector from the power jack, and then re-plug the connector to  
restart the AP.  
¾
Report this problem to our technical support staff.  
If the AP still does not work after being restarted, some hardware components of the AP may  
have failed.  
¾
Contact our technical support staff.  
B-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
C
Appendix  
C
Regulatory Statement  
Federal Communication Commission Interference Statement  
This equipment has been tested and found to comply with the limits for a Class B digital device,  
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection  
against harmful interference in a residential installation. This equipment generates, uses and can  
radiated radio frequency energy and, if not installed and used in accordance with the instructions,  
may cause harmful interference to radio communications. However, there is no guarantee that  
interference will not occur in a particular installation. If this equipment does cause harmful  
interference to radio or television reception, which can be determined by turning the equipment off  
and on, the user is encouraged to try to correct the interference by one of the following measures:  
y
y
y
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is  
connected.  
y
Consult the dealer or an experienced radio/TV technician for help.  
FCC Caution: To assure continued compliance, (example – use only shielded interface cables  
when connecting to computer or peripheral devices). Any changes or modifications not expressly  
approved by the party responsible for compliance could void the user’s authority to operate this  
equipment.  
This transmitter must not be co-located or operating in conjunction with any other antenna or  
transmitter.  
FCC Radiation Exposure Statement  
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled  
environment. This equipment should be installed and operated with minimum distance 20 cm  
between the radiator & your body.  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two  
conditions: (1) This device may not cause harmful interference, and (2) this device must accept  
any interference received, including interference that may cause undesired operation.  
R&TTE Compliance Statement  
This equipment complies with all the requirements of DIRECTIVE 1999/5/CE OF THE  
EUROPEAN PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio equipment and  
telecommunication terminal equipment and the mutual recognition of their conformity (R&TTE).  
The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications  
Terminal Equipment and Satellite Earth Station Equipment) as of April 8,2000.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
NI WAP-3701/3711 User’s Manual  
Regulatory Statement  
Safety  
This equipment is designed with the utmost care for the safety of those who install and use it.  
However, special attention must be paid to the dangers of electric shock and static electricity when  
working with electrical equipment. All guidelines of this and of the computer manufacture must  
therefore be allowed at all times to ensure the safe use of the equipment.  
EU Countries Intended for Use  
The ETSI version of this device is intended for home and office use in Austria, Belgium, Denmark,  
Finland, France (with Frequency channel restrictions), Germany, Greece, Ireland, Italy,  
Luxembourg, Portugal, Spain, Sweden, The Netherlands, and United Kingdom.  
The ETSI version of this device is also authorized for use in EFTA member states Norway and  
Switzerland.  
EU Countries Not Intended for Use  
None.  
Potential Restrictive Use  
France: only channels 10, 11, 12, and 13.  
C-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
D
Appendix  
D
Technical Support and Professional  
Services  
Visit the following sections of the National Instruments Web site at ni.com for technical support  
and professional services:  
y Support— Online technical support resources at ni.com/support include the following:  
Self-Help Resources— For answers and solutions, visit the award-winning National  
Instruments Web site for software drivers and updates, a searchable KnowledgeBase, product  
manuals, step-by-step troubleshooting wizards, thousands of example programs, tutorials,  
application notes, instrument drivers, and so on.  
Free Technical Support— All registered users receive free Basic Service, which includes  
access to hundreds of Application Engineers worldwide in the NI Discussion Forums at  
ni.com/forums. National Instruments Application Engineers make sure every question receives  
an answer.  
For information about other technical support options in your area, visit ni.com/services or  
contact your local office at ni.com/contact.  
y Training and Certification— Visit ni.com/training for self-paced training, eLearning virtual  
classrooms, interactive CDs, and Certification program information. You also can register for  
instructor-led, hands-on courses at locations around the world.  
y System Integration— If you have time constraints, limited in-house technical resources, or  
other project challenges, National Instruments Alliance Partner members can help. To learn  
more, call your local NI office or visit ni.com/alliance.  
y Declaration of Conformity (DoC)— A DoC is our claim of compliance with the Council of  
the European Communities using the manufacturer’s declaration of conformity. This system  
affords the user protection for electronic compatibility (EMC) and product safety. You can  
obtain the DoC for your product by visiting ni.com/certification.  
y Calibration Certificate— If your product supports calibration, you can obtain the calibration  
certificate for your product at ni.com/calibration.  
If you searched ni.com and could not find the answers you need, contact your local office or NI  
corporate headquarters. Phone numbers for our worldwide offices are listed at the front of this  
manual. You also can visit the Worldwide Offices section of ni.com/niglobal to access the branch  
office Web sites, which provide up-to-date contact information, support phone numbers, email  
addresses, and current events.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
NI AirWorks NI-WAP-3701/3711 User’s Manual  
Service Information  
Worldwide Technical Support and Product Information  
ni.com  
National Instruments Corporate Headquarters  
11500 North Mopac ExpresswayAustin, Texas 78759-3504USATel: 512 683 0100  
Worldwide Offices  
Australia 1800 300 800, Austria 43 662 457990-0, Belgium 32 (0) 2 757 0020, Brazil 55 11 3262  
3599, Canada 800 433 3488, China 86 21 5050 9800, Czech Republic 420 224 235 774, Denmark  
45 45 76 26 00, Finland 358 (0) 9 725 72511, France 01 57 66 24 24, Germany 49 89 7413130,  
India 91 80 41190000, Israel 972 3 6393737, Italy 39 02 413091, Japan 81 3 5472 2970, Korea 82  
02 3451 3400, Lebanon 961 (0) 1 33 28 28, Malaysia 1800 887710, Mexico 01 800 010 0793,  
Netherlands 31 (0) 348 433 466, New Zealand 0800 553 322, Norway 47 (0) 66 90 76 60, Poland  
48 22 3390150, Portugal 351 210 311 210, Russia 7 495 783 6851, Singapore 1800 226 5886,  
Slovenia 386 3 425 42 00, South Africa 27 0 11 805 8197, Spain 34 91 640 0085, Sweden 46 (0) 8  
587 895 00, Switzerland 41 56 2005151, Taiwan 886 02 2377 2222, Thailand 662 278 6777,  
Turkey 90 212 279 3031, United Kingdom 44 (0) 1635 523545  
For further support information, refer to the Cross referenceolor:Blueparatext appendix. To  
comment on National Instruments documentation, refer to the National Instruments Web site at  
ni.com/info and enter the info code feedback.  
© 2007 National Instruments Corporation. All rights reserved.  
D-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Miele Convection Oven H 5040 B User Manual
Mr Coffee Coffeemaker GB Series User Manual
MTD Backyard Playset A06 User Manual
Mustek Computer Monitor TP 6000 User Manual
NETGEAR Network Card GA621 User Manual
NETGEAR Network Router JWNR2010v3 User Manual
Olympus Camera Accessories PT 036 User Manual
Oregon Scientific Weather Radio RMR802 User Manual
Palsonic VCR VCR2120 User Manual
Panasonic Camcorder AG DVC 200E User Manual