Napoleon Fireplaces DVD VCR Combo NZ 26 User Manual

TABLE of CONTENTS

PG 2-6 INTRODUCTION

OPTIONAL BLOWER

Warnings and Safety Precautions

FEATURES

Speciﬁcations

Warranty

Installation Overview

General Instructions

General Information

Controlling Combustion Air

Achieving Proper Draft

17-18 OPERATING INSTRUCTIONS

Fuel Loading and Burn Cycle

Ash Removal Procedures

Care of Glass and Plated Parts

HI-EFFICIENCY HEATING

MAINTENANCE

Five Options

Gasket / Bafﬂe Replacement

Door Glass Replacement

8-11 INSTALLATION / FRAMING

Creosote Formation And Removal

Run-Away or Chimney Fire

Fire Extinguishers and Smoke Detectors

Woodpile Maintenance

Location and Clearances

Framing

Finishing

Enclosure Finishing and Enclosure Alternate Finishing

Outside Combustion Air

Mantel Clearances

19-20 REPLACEMENTS

Ordering Replacement Parts

Replacement Parts

Accessories

Hearth Extension

11-13 CHIMNEY INSTALLATION

Adding Chimney Sections

Offset Chimney Installation

Installing Flashing and Storm Collar

Connection to a Masonry Chimney

TROUBLE SHOOTING

SERVICE HISTORY

14-15 FINAL ASSEMBLY

23-24 NOTES

Attaching the Handle

Top Firebrick and Bafﬂe Installation

NOTE: Changes, other than editorial, are denoted by a vertical line in the margin.

Congratulations on the purchase of your hi-tech, high efﬁciency solid fuel burning ﬁreplace! It has been extensively tested

in Canadian and American laboratories.

SPECIFICATIONS

FIGURE 1

W415-0676 / 03.14.08

Download from Www.Somanuals.com. All Manuals Search And Download.

Download from Www.Somanuals.com. All Manuals Search And Download.

NAPOLEON® products are manufactured under the strict Standard of the World Recognized

ISO 9001 : 2000 Quality Assurance Certificate.

NAPOLEON® products are designed with superior components and materials, assembled by trained craftsmen who take great

pride in their work. The complete fireplace is thoroughly inspected by a qualified technician before packaging to ensure that you,

the customer, receives the quality product that you expect from NAPOLEON®.

NAPOLEON® WOOD FIREPLACE PRESIDENT'S LIFETIME LIMITED WARRANTY

The following materials and workmanship in your new NAPOLEON® wood fireplace are warranted against defects for

as long as you own the fireplace. This covers: combustion chamber, heat exchanger, stainless steel baffle retainer, ceramic

glass (thermal breakage only), gold plated parts against tarnishing, porcelainized enamelled components, aluminum extrusion

trims ash drawer, and cast iron castings.

Electrical (110V) components and wearable parts such as blowers, thermal switch, switches, wiring, firebrick, gasketing, and

high temperature paint are covered and NAPOLEON® will provide replacement parts free of charge during the first year

of the limited warranty.

Labour related to warranty repair is covered free of charge during the first year. Repair work, however, requires the prior

approval of an authorized company official. Labour costs to the account of NAPOLEON® are based on a predetermined rate

schedule and any repair work must be done through an authorized NAPOLEON® dealer.

CONDITIONS AND LIMITATIONS

NAPOLEON® warrants its products against manufacturing defects to the original purchaser only -- i.e., the individual or legal entity

(registered customer) whose name appears on the warranty registration card ﬁled with NAPOLEON® -- provided that the purchase was

made through an authorized NAPOLEON® dealer and is subject to the following conditions and limitations:

This factory warranty is non-transferable and may not be extended whatsoever by any of our representatives.

The wood ﬁreplace must be installed by an authorized service technician or contractor. Installation must be done in accordance with

the installation instructions included with the product and all local and national building and ﬁre codes.

This limited warranty does not cover damages caused by misuse, lack of maintenance, accident, alterations, abuse or neglect and

parts installed from other manufacturers will nullify this warranty.

This limited warranty further does not cover any scratches, dents, corrosion or discoloring caused by excessive heat, abrasive and

chemical cleaners nor chipping on porcelain enamel parts, nor any venting components used in the installation of the ﬁreplace.

In the ﬁrst year only, this warranty extends to the repair or replacement of warranted parts which are defective in material or workmanship

provided that the product has been operated in accordance with the operation instructions and under normal conditions.

After the ﬁrst year, with respect to the President's Limited Lifetime Warranty, NAPOLEON® may, at its discretion, fully discharge all

obligations with respect to this warranty by refunding to the original warranted purchaser the wholesale price of any warranted but

defective part(s).

After the ﬁrst year, NAPOLEON® will not be responsible for installation, labour or any other costs or expenses related to the reinstallation

of a warranted part, and such expenses are not covered by this warranty.

Notwithstanding any provisions contained in the President's Limited Lifetime Warranty, NAPOLEON’S responsibility under this warranty

is deﬁned as above and it shall not in any event extend to any incidental, consequential or indirect damages.

This warranty deﬁnes the obligations and liability of NAPOLEON® with respect to the NAPOLEON® wood ﬁreplace and any other

warranties expressed or implied with respect to this product, its components or accessories are excluded.

NAPOLEON® neither assumes, nor authorizes any third party to assume, on its behalf, any other liabilities with respect to the sale

of this product. NAPOLEON® will not be responsible for: over-ﬁring, downdrafts, spillage caused by environmental conditions such as

rooftops, buildings, nearby trees, hills, mountains, inadequate vents or ventilation, excessive venting conﬁgurations, insufﬁcient makeup

air, or negative air pressures which may or may not be caused by mechanical systems such as exhaust fans, furnaces, clothes dryers,

etc.

Any damages to ﬁreplace, combustion chamber, heat exchanger, brass trim or other component due to water, weather damage, long

periods of dampness, condensation, damaging chemicals or cleaners will not be the responsibility of NAPOLEON®.

The bill of sale or copy will be required together with a serial number and a model number when making any warranty claims from

your authorized dealer. The warranty registration card must be returned within fourteen days to register the warranty.

NAPOLEON® reserves the right to have its representative inspect any product or part thereof prior to honouring any warranty

claim.

ALL SPECIFICATIONS AND DESIGNS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE DUE TO ON-GOING PRODUCT IMPROVEMENTS. NAPOLEON® IS A

REGISTERED TRADEMARK OF WOLF STEEL LTD. PATENTS U.S. 5.303.693.801 - CAN. 2.073.411, 2.082.915. © WOLF STEEL LTD.

W415-0676 / 03.14.08

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION OVERVIEW

FIGURE 2

WARNING

This ﬁreplace and its components are designed to be installed and

operated as a system. Any alteration to or substitution for items in

this system, unless allowed by these installation instructions, will

void the Warnock Hersey, listing and may void the product war-

ranty. It may also create a hazardous installation. Read through

these instructions thoroughly before starting your installation and

follow them carefully throughout your project.

W415-0676 / 03.14.08

Your ﬁreplace must be installed in accordance with all national and local

building code standards and the standard of Chimney and Fireplaces,

Vents and Solid Fuel Burning Appliances NFPA #211. Consult the

authority having jurisdiction (such as municipal building department,

ﬁre department, ﬁre prevention bureau, etc.) to determine the need

to obtain a permit. If you are in doubt about the proper installation for

your situation, contact your dealer or local building or ﬁre ofﬁcial. The

manufacturer does not guarantee that this ﬁreplace and its options will

completely heat your entire home.

GENERAL INSTRUCTIONS

This is the most efﬁcient,

simple and trouble free

woodburning system

we know of and works

as follows:

Expansion / contraction noises during heating up and cooling down

cycles are normal and to be expected.

Mobile home installation requires that the ﬁreplace be secured

to the ﬂoor. It is recommended that in all cases, the ﬁreplace be

secured to the ﬂoor. Use the pallet packing brackets to accomplish

FIGURE 3

this.

CARE OF GLASS AND PLATED PARTS

If the glass is not kept clean permanent discoloration and / or blem-

ishes may result. Normally a hot ﬁre will clean the glass. The most

common reasons for dirty glass include: not using sufﬁcient fuel to

get the stove thoroughly hot, using green or wet wood, closing the

draft so far that there is insufﬁcient air for complete combustion. If it

is necessary to clean the glass, use a soft cloth with a non-abrasive

cleaner. Do not clean the glass when hot!

Primary combustion air enters through the air control inlet box regulated

by a draft control, travels up the side through a duct and enters the top

centre of the combustion chamber into a preheating airwash located

across the top and then down the window to feed the ﬁre and also to

ensure that the glass remains clean.

Secondary air feeds directly into the combustion chamber at hearth level

through the log retainer and also through inlets located at the bottom

back corners of the combustion chamber. This air travels up the riser

to the four secondary air tubes located at the top and shoots out laterally

to oxidize the gases rising to the smoke exit.

The glass is very strong but do not let burning fuel rest or fall against it

and always close the door gently. Never force it shut!

If the glass should ever crack while the ﬁre is burning, do not open the

door until the ﬁre is out and do not operate the stove again until the glass

has been replaced with a new 5mm thick piece of ceramic glass, available

from your authorized dealer. Do not substitute materials.

For information on glass removal and replacement, see Mainte-

nance.

Do not use abrasive cleaners to clean plated parts. Buff lightly with a

clean dry cloth.

Prolonged high temperature burning with the door ajar may cause a

permanent rainbowing effect on the lower edge of a gold plated door.

The combustion chamber is lined with high-temperature ﬁrebrick on

all sides, and across the bottom to maintain a high temperature in the

combustion chamber so that gases mixing with the preheated air from

the secondary air tubes are easily ignited and burned. The ﬁreplace

sides and back permit a zero clearance installation and direct the

heat upwards and forwards into the room. Be sure to provide suf-

ﬁcient combustion air. There are many other appliances in your home

competing for air such as a kitchen range hood, forced air heating

devices or a bathroom exhaust fan.

If the outside air feature is utilized, you will never experience a

shortage of combustion air. If you choose not to utilize outside air

and experience draft or smoking problems, you may need to open

a door or window.

NOTE: The protective wrap on plated parts is best removed when

the assembly is at room temperature but this can be improved if the

assembly is warmed, using a hair dryer or similar heat source.

After extended periods of non-operation such as following a vacation

or a warm weather season, the ﬁreplace may emit a slight odour for

a few hours. This is caused by dust particles on the ﬁrebox burning

off. Open a window to sufﬁciently ventilate the room.

GENERAL INFORMATION

CALIFORNIA PROP 65 WARNING:

Use of this product may produce smoke which contains chemi-

cals known to the State of California to cause cancer, birth

defects, or other reproductive harm.

Do not use makeshift compromises during installation.Do

not block or restrict air, grille or louvre openings! Do not

add a hood.

When the appliance is equipped with a 24 karat gold-plated door,

you must clean all the ﬁngerprints and oils from the gold surface

before ﬁring the appliance for the ﬁrst time. Use a glass cleaner

or vinegar and towel to remove the oils. If not cleaned properly

before lighting your ﬁrst ﬁre, the oils can cause permanent mark-

ings on the gold plating. After the gold plating is cured, the oils will

not affect the ﬁnish and little maintenance is required, just wipe

clean as needed.

Burning your unit with the ash dump door open or ajar

creates a ﬁre hazard that may result in discoloration to

the gold plated door, internal damage to the ﬁreplace or

a house and/or chimney ﬁre.

All venting connections must be in compliance with the chimney manu-

facturers installation instructions.

Clearances referred to throughout this manual are the minimum re-

quirements.

W415-0676 / 03.14.08

Download from Www.Somanuals.com. All Manuals Search And Download.

Download from Www.Somanuals.com. All Manuals Search And Download.

HI-EFFICIENCY HEATING

FIVE OPTIONS

ATTIC

To operate this hi-efﬁciency ﬁreplace as a basic system, the blower

is not required, however, to enhance its efﬁciency a blower is rec-

ommended.

OPTION

FOR

TYING

INTO

EXISTING

DUCT

WORK

A BLOWER KIT (NZ62) This blower is installed in the bottom of the unit

and used to direct the heat into the room where the ﬁreplace is lo-

cated. The blower is controlled, by a variable speed switch, located

inside the ﬁreplace.

BLOWER

LOCATION

OPTIONS

A THERMOSTATIC AIR CONTROL (NZ690KT) may be used for constant

heat, complete with automatic damper and thermostat, wall mounted

in the room containing the ﬁreplace, and at least 10 feet (minimum)

from the ﬁreplace.

A HOT AIR GRAVITY VENT SYSTEM (NZ220) may be used to distribute

heat to an adjoining room (located either above, or beside the room

containing the ﬁreplace) by way of vents, eliminating the need of

an additional blower. While this system may be used in conjunction

with the optional blowers, it could reduce the ﬂow of hot air being

distributed to additional rooms. It must be experimented with and

the dampers adjusted manually to suit your requirements. This

may take a few attempts; thereafter adjustments should no longer

be required as is normally experienced with your central heating

system registers.

FIGURE 5b

AHOT AIR DISTRIBUTION KIT (GA-566) may be used to distribute warm

air from the ﬁreplace base (only) into a separate location in the

home.

These options may be incorporated with one another. If the optional

blowers are to be installed, make provision during framing to route a

110 volt power line to the ﬁreplace. Detailed installation instructions

are included with each venting kit.

The heat shield cover plate must be removed before installing

the gravity vent. The hot air vent must be installed in an upward

direction! NEVER install in a downward direction. Figure 6. The

hot air gravity vent system is not to be connected to a central

heating system (for this application use the NZ62CH). This

option may not be used in mobile homes.

GRAVITY VENT

OPTION (1 DUCT)

DUCTING

GRAVITY VENT

OPTION (2 DUCTS)

GRAVITY VENT OPTION

RIGHT SIDE

ONLY

No more than two hot air gravity vents can be installed to ﬁreplace.

Individual vent runs are not to exceed 10 feet.

CENTRAL HEATING

BOTTOM

CENTRAL HEATING &

GRAVITY VENT OPTION

CENTRAL HEATING

All hot air gravity vents must be insulated.

HEAT SHIELD COVER PLATE

MASONRY APPLICATION ONLY

FIGURE 6

WARNING

STOVE TOP

FIGURE 4

Do not draw outside air from garage spaces. Exhaust products of

gasoline engines are hazardous.

A CENTRAL HEATING SYSTEM (NZ62CH) may be used to heat rooms up to

50 feet from the unit. A wall mounted thermostat located in the room

to be heated controls the blower supplying warm air from the room

containing the ﬁreplace. If a hot air duct system exists, the central

heat blower may safely be tied into this system to reduce the amount

of new ducting required. Consult with a heating specialist to ensure

a proper duct layout for your home. If the NZ62CH is installed at the

bottom of the unit, it could introduce a cool draft into the room that

Do not install outside air ducts such that the air my be drawn from

attic spaces, basements or above the rooﬁng where other heat-

ing appliances or fans and chimneys exhaust or utilize air. These

precautions will reduce the possibility of ﬁreplace smoking or air

ﬂow reversal. The outside air inlet must remain clear of leaves,

debris ice and/or snow. It must be unrestricted while unit is in use

to prevent room air starvation which can cause smoke spillage

and an inability to maintain a ﬁre. Smoke spillage can also set off

smoke alarms.

the ﬁreplace is installed in.

When attached to the top or sides of the unit, it provides a higher heat

output. This option may not be used in mobile homes.

To prevent contact with sagging or loose insulation, the ﬁreplace

must not be installed against vapour barriers or exposed insulation.

Localized overheating could occur and a ﬁre could result.

FIGURE 5a

W415-0676 / 03.14.08

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION / FRAMING

WARNING

Before starting, do the following:

1. For protection wear gloves and safety glasses.

2. Keep hand tools in good condition, sharpen cutting edges and make sure tool handles are secure.

3. Always maintain the minimum air space required to the enclosure to prevent ﬁres.

MAINTAIN THESE MINIMUM CLEARANCES TO

COMBUSTIBLES:

Fireplace framing:

Top Stand-Off

WARNING

Carefully follow the instructions for assembly of the chimney and other

parts needed to install this ﬁreplace. Failure to do so may result in a ﬁre,

especially if combustibles are too close to the ﬁreplace or chimney and

air spaces are blocked, preventing the free movement of cooling air.

Rear Stand-Off

Side

Fireplace ﬁnishing:

Sides

6 / "

Top

6 / "

LOCATION AND CLEARANCES

Factory Built Chimney

Hot Air Gravity Ductwork Insulation

*Base of unit to ceiling

Do not build shelves or cupboards into the area above

the ﬁreplace.

72"

Base of unit to enclosure top

While the ﬁreplace can be installed directly on the ﬂoor, a non-

combustible hearth extension is required in front of the ﬁreplace,

that must not be built higher than the bottom of the ﬁreplace to

avoid air ﬂow blockage. It may therefore be advisable to build the

ﬁreplace on a raised platform. The minimum distance between the

edge of the ﬁreplace and any adjacent wall, at right angles to it, is

21". A wall projecting at 45° from the outer edge of the ﬁreplace is

allowed; projections into this area are permitted. Do not install into

any area having a height less than 6 feet (ceiling to ﬁreplace base,

excluding hearth height). See Section on Framing. The location of

windows, doors and the trafﬁc ﬂow in the room where the stove is

to be located should be considered. If possible, you should choose

a location where the chimney will pass through the house without

cutting a ﬂoor or roof joist.

Enclosure must have ventilation

between 72" and 84"

84" if installing optional hot air gravity vent system, NZ220 on the

same ﬂoor as the ﬁreplace.

FRAMING

NOTE:Inordertoavoidthepossibil-

ityofexposedinsulationorvapour

barrier coming in contact with the

ﬁreplacebody,itisrecommended

that the walls of the fireplace

enclosure be “ﬁnished”

(i.e.: drywall/sheetrock),

as you would ﬁnish any

other outside wall of a

home. This will ensure

that clearance to com-

FIGURE 7a: Framing Requirements

bustiblesismaintained

within the cavity.

WARNING

NOTE: Do not build into this area - it must

be left clear to provide adequate clearance

for the vent in this 14” wide area centered

along the front of the fireplace. No combus-

tibles are allowed.

3 1/2” MAX

72”

MINIMUM

ENCLOSURE

HEIGHT

FIGURE 7b

14” MAX

1 1/2”

MAX

25 3/4”

44 3/4”

50 3/4”

W415-0676 / 03.14.08

Download from Www.Somanuals.com. All Manuals Search And Download.

The ﬁreplace should be framed using 2x4 lumber. For the header and cripple studs above the ﬁreplace it is recommended to use steel. The

ﬁreplace must be secured to the ﬂoor in all cases. Use the pallet packing brackets to secure to the ﬂoor. If ducting is to be installed, the

minimum enclosure ceiling height is 84". Without ducting, the ceiling height may be brought down to a minimum of 72". However a ﬁreplace

enclosure with a height less than 84" must be provided with sufﬁcient air circulation to avoid a ﬁre hazard. Install ventilation grilles (minimum

openings of 40 sq. inches) at both ﬂoor and ceiling levels of the enclosure.

Do not place insulation into the enclosure around the ﬁreplace or the chimney. Combustible framing materials must not be closer

than 6" from the side of the unit and 5" from the top of the unit.

FIGURE 7c: Finishing Requirements

FINISHING

Clearances to ﬁnishing materials: 6³

" minimum of non-combustible material to the top of the unit and a minimum 6 3/4" to either

side.

Objects placed in front of the ﬁreplace must be kept a minimum of 48" away from the front face of the unit.

Non-combustible material (brick, stone, cement board or ceramic tile) may protrude over the black painted surface of the ﬁreplace front.

W415-0676 / 03.14.08

W415-0676 / 03.14.08

Download from Www.Somanuals.com. All Manuals Search And Download.

Download from Www.Somanuals.com. All Manuals Search And Download.

OUTSIDE COMBUSTION AIR

MANTEL CLEARANCES

Model NZ-26 has the option of taking outside air directly into the Mantel clearance can

ﬁreplace through the opening on the left hand side or taking inside vary according to the

air through the lower front louvres or a combination of both.

mantel depth.

If the optional fresh air kit (available through your authorized dealer)

is installed, it must not draw air from the attic or garage. It may only

come from outside the house. The maximum length of the 4" air duct

is 20 feet; thereafter enlarge the duct to a 6" diameter.

Decide on the most convenient location for the fresh air inlet duct and

hood which may be installed above or below ﬂoor level.

Make a 5" hole in an outside wall of the house. From outside, place

the fresh air hood into the hole, open side down.

FIGURE 10

At each end, carefully pull back the insulation sleeve exposing the

ﬂexible duct. Place the insulated ﬂexible duct over the fresh air hood

and over the ﬁreplace outside air connector. Carefully push the insula-

tion sleeve back over the duct. Using the clamps, fasten the insulated

duct into place on both sides. Figure 9.

For outside air only, re-install the inside air cover plate, shown in

Figure 37, to cover the control box inside air opening. See Section

on Combustion Air Control.

A chimney venting the ﬁreplace shall not vent any other appliance.

HEARTH EXTENSION

An acceptable 16" x 50" non-combustible (i.e.: brick, stone or ceramic

tile) hearth extension must be installed. Ensure that the gap between

the ﬁreplace and a factory-built hearth extension is sealed with sand/

cement grout or covered with a metal strip (or both) to prevent sparks

and embers from falling into this area. A raised hearth together with

the ﬁreplace built on a raised platform is recommended for easier

wood loading and ﬁre viewing.

WARNING

Hearth extensions are to be installed only as described to prevent

high temperatures from occurring on concealed combustible ma-

terials. Hearth sealing strips prevent burning or hot particles from

inadvertently falling directly on combustible surfaces in the event

the building should settle and disturb the original construction.

FIGURE 9

CHIMNEY INSTALLATION

If the chimney system is enclosed within the attic area, a rafter radia-

tion shield is required.

WARNING

The chimney must extend at least 3 feet above its point of contact

with the roof and at least 2 feet higher than any wall, roof or building

within 10 feet.

Never install a single wall slip section or smokepipe in a chase

structure. The higher temperature of this single wall pipe may

radiate sufﬁcient heat to combustible chase materials to cause

a ﬁre.

If the chimney extends more than 5 feet above the roof, it must be

secured using a roof brace or guide wires.

Ensure that minimum clearances are maintained

To avoid danger of ﬁre, all instructions must be strictly followed,

including the provision of air space clearance between chimney

system and enclosure. To protect against the effects of corrosion

on those parts exposed to the weather, we recommend that the

chase top be painted with a rust-resistant paint.

Portions of the chimney that extend through accessible spaces must

always be encased to avoid personal contact with the chimney and

thereby avoid damage to the chimney.

A raincap must be installed to avoid internal damage and corro-

sion.

Maintain a minimum 2" air clearance to all parts of the chimney

system at all times. Failure to maintain this 2" air clearance will

cause a structure ﬁre.

The chimney must be supported at a maximum of 20 foot intervals

(approx. 200 lbs/20 ft).

Detailed instructions for installation of the chase top, storm collar

and termination cap are packaged with these parts.

The NZ-26 was tested to CAN/ULC S610 and UL 127 Factory Built

Fireplace Standards. This ﬁreplaces has met the test criteria for

Zero Clearance Installation to Combustible Surfaces and Certiﬁed

to burn Firewood only.

Firestop spacers must be used whenever the chimney penetrates

a ceiling/ﬂoor area.

Any 6" diameter chimney listed to these standards may be installed.

In accordance with these standards, the unit may also be connected

to any chimney listed to CAN/ULC-S609 and ULC-S629 for Canada

or UL-103HT for the United States.

A chimney venting the ﬁreplace shall not vent any other appliance.

The minimum overall chimney height from the top of the ﬁreplace

is 11 feet.

Installation of all types of factory-built chimney systems is to be in

accordance with the chimney manufacturers installation instructions.

An appropriate chimney manufacturers anchor base plate and anchor

base plate gasket is required in order to initiate the twist lock mecha-

nism. Use the high temperature gasket, supplied, to seal between

The maximum overall chimney height from the top of the ﬁreplace

is 34 feet.

Factory-built chimney systems for use in dwellings constructed for

three or more families must be enclosed above the room in which

the ﬁreplace is located. This enclosure must have a ﬁre resistance

rating equal to or greater than that of the ﬂoor or roof assembly

through which they pass.

the anchor plate and the ﬁreplace top.

W415-0676 / 03.14.08

Download from Www.Somanuals.com. All Manuals Search And Download.

FIGURE 11 - STRAIGHT UP

FIGURE 12 - 2 ELBOWS

FIGURE 13 - 4 ELBOWS

Single off-set with two 15°, 30° or 45°

elbows. Minimum overall chimney height

is 11 feet.

Double off-set with four 15°, 30° or 45°

elbows. Minimum overall chimney height

is 11 feet.

No Off-Set. Minimum overall chimney height

is 11 feet.

* The ﬁrst ﬂue offset closest to the top of the unit must be a

minimum distance of 12" from the top of the ﬁreplace.

NOTE: 30° or 45° offsets may be installed back to back.

ADDING CHIMNEY SECTIONS

1. Move the ﬁreplace into position. Try to centre the exhaust ﬂue of

the ﬁreplace, midpoint between two joists to prevent having to cut

them. Use a plumb bob to line up the centre.

2. Cut and frame an opening in the ceiling to provide a minimum clear-

ance of 2" between the outside of the chimney and any combustible

material. DO NOT FILL THIS SPACE WITH ANY TYPE OF MATE-

RIAL! Nail headers between the joists for extra support. Firestop

spacers must be placed on the bottom of each framed opening in

any ﬂoor or ceiling that the chimney passes through.

Add chimney sections, twist locking (clockwise) securely, to the

required height. Use a rafter radiation shield whenever the chimney

system is enclosed within an attic area.

3. Hold a plumb bob from the underside of the roof to determine

where the opening in the roof should be. Cut and frame the roof

opening maintaining proper 2" clearances.

FIGURE 16

FIGURE 14

OFFSET CHIMNEY INSTALLATION

The ﬁrst ﬂue offset closest to the top of the unit must

be a minimum distance of 12" from the top of the ﬁre-

place.

An insulated elbow must be used when it becomes necessary to

offset the chimney in order to clear a joist or to pass through an

upstairs closet.

Attach an elbow to the chimney section, angled toward the offset.

Secure with 3 - #8X1/2" sheet metal screws. To achieve the mini-

mum offset, attach and secure a return elbow to the ﬁrst. To achieve

longer offsets, you may install any available length of chimney pipe

between the elbows.

FIGURE 15

Supports must be used on the ﬁrst vertical chimney section after a

return elbow.

WARNING

Chimney sections installed between an offset and return require

structural support to reduce off-center loading and to prevent

chimney sections from separating at the chimney joints.

The chimney should not be built with an offset angle in excess of

45° in Canada and 30° in USA. Do not combine offset chimney

components to exceed these angles.

W415-0676 / 03.14.08

IF THE CHIMNEY IS

UNLINED:

FIGURE 17

A stainless steel

liner listed to either

S t a n d a r d U L C -

S640M, ULC-S639 in

Canada or UL-1777

in the USA: Liners

for New Masonry

Chimneys, may be

used to connect

the fireplace to the

chimney. The liner

must be continuous

from the fireplace

to the chimney cap

and be installed only

per manufacturers

i n s t r u c t i o n s .

Figure 19. In both

cases, the chimney

INSTALLING FLASHING AND

STORM COLLAR

Remove the nails from the shingles above and to the sides of the

chimney. Place the ﬂashing over the chimney pipe and slide under-

neath the sides and upper edge of the shingles. Ensure that the chim-

ney pipe is properly centered within the ﬂashing, giving a 3/4" margin

all around. Fasten to the roof on the top and sides. DO NOT NAIL

through the lower portion of the ﬂashing. Make weather-tight by seal-

ing with caulking. Where possible, cover the sides and top edges of

the ﬂashing with rooﬁng material.Apply waterproof caulking, provided

with the ﬂashing, around the chimney, 1" above the top of the ﬂashing

and push the storm collar down into the caulking. Insert a rain cap

onto the top of the last chimney section.

FIGURE 20

structure must be supported by angle iron anchored into the masonry

walls. Figures 19 & 20. The allowable masonry used in chimney

construction is 3-1/2" brick, solidly mortared and fully encasing the

ﬂue. Ensure there are no leaks.

In no case is the masonry enclosure to be supported by the NZ-26

ﬁreplace. Allow a 1" (one inch) air cavity for expansion.

FIGURE 18

ANCHOR PLATE

HI-TEMP GASKET

FIREPLACE TOP

FIGURE 21

FLUE TILE SUPPORT FOR A MASONRY FIREPLACE

CONNECTION TO A MASONRY

CHIMNEY

HI-TEMP GASKET

FIREPLACE TOP

Model NZ-26 may be connected

to either a lined or unlined

masonry chimney.

FIGURE 22

For a masonry ﬁreplace use a ﬂue tile support. For a pre-fabricated

chimney use an anchor plate.

IF THE CHIMNEY IS LINED,

the flues must be made of

vitriﬁed clay and be in sizes of

8" square, 8" x 12", or 8" round

with a minimum height of 11

feet above the fireplace. 8"

round ﬂues are recommended.

Installation must conform to

both national and local code

requirements.

FIGURE 19

W415-0676 / 03.14.08

Download from Www.Somanuals.com. All Manuals Search And Download.

Download from Www.Somanuals.com. All Manuals Search And Download.

FINAL ASSEMBLY

ATTACHING THE HANDLE

Attach the handle as shown so that

when the door is closed, the handle

will be centred in the slot located on the

ﬁreplace front. To achieve this you may

have to experiment (on the upper and

lower screws) with one of the variations

shown. Tighten securely.

TOP FLAME SPREADER

BOTTOM FLAME SPREADER

FIBRE BAFFLE (1 OF 2 SHOWN)

TOP FIREBRICK (1 OF 2 SHOWN)

FIGURE 23

FIGURE 28

FIGURE 24

FIGURE 25

WARNING

Operation of the ﬁreplace without the top ﬁrebricks and the

bafﬂes can result in excessive temperatures that could dam-

age the ﬁreplace, chimney and the surrounding enclosure.

TOP FIREBRICK AND BAFFLE

INSTALLATION

The ﬁreplace is shipped with the ﬁrebricks in place. Top ﬁrebricks,

ﬁbre bafﬂes and gasket rope are not installed.

BAFFLE SUPPORT BRACKET

FIBRE BAFFLE

TOP FIREBRICK

TUBE

RETAINER

FIGURE 26

FIGURE 29

Unscrew and remove the front tube retainer. Note that the ﬁrst

tube retainer also holds the side brick in place. Slide the tube

Insert the left bafﬂe, then the left top ﬁrebrick. Repeat using

either to the left or right and remove. Remove the two middle

tubes in the same fashion.

the right bafﬂe and brick.

The bafﬂes are made of a brittle material. Care must be taken

not to bend or force them.

Replace the three front tubes. Position the center edg-

es of both baffles and bricks until they lie snugly together.

Slide the bafﬂe support bracket into place along the front of the unit

between the front tube and the two top ﬁrebricks.

REAR

BRICKS

GASKET ROPE LOCATION

FIGURE 27

Place gasket rope along the upper ledge of the air chamber

and on the top of the rear bricks. The top and bottom ﬂame

spreaders come taped together. This tape will burn away in the initial

ﬁring of the unit. On subsequent brick removals, the bottom ﬂame

spreader must be taped to the top spreader to ease top brick and

bafﬂe removal and to avoid damaging the ﬁbre bafﬂes.

FIGURE 30

W415-0676 / 03.14.08

If you need to remove the bricks (to lighten the ﬁreplace for ease of

installation, replacement, etc), follow this sequence:

For Firebrick Removal: Remove the ashwell grate. This allows

the four bottom bricks to be removed ﬁrst.

Slide out the bafﬂe support bracket from above the front tube.

Reaching above the top ﬁrebricks and bafﬂes, lift and tape the bot-

tom ﬂame spreader to the top spreader to ease top brick and bafﬂe

removal and to avoid damaging the ﬁbre bafﬂe. Remove the three

front tubes.

Remove the top ﬁrebrick on the right, then the left ﬁrebrick. Remove

the bafﬂes, starting with the right side.

Remove the gasket rope. Check the rope for deterioration and replace

if necessary. Remove the rear bricks (pull the two bricks forward at

the centre, and lift the bottom of the bricks out). Remove the side

bricks (tilt the tops inward).

FIGURE 31

TOP FLAME SPREADER

BOTTOM FLAME SPREADER

FIBRE BAFFLES

TOP FIBREBRICKS

BAFFLE SUPPORT

TUBE BURNERS

GASKET

RIGHT SIDE FIBREBRICK

LEFT SIDE FIBREBRICK REAR FIBREBRICKS

BOTTOM LEFT FIBREBRICK

BOTTOM RIGHT FIBREBRICK

RIGHT FRONT FIBREBRICK

LEFT FRONT FIBREBRICK

W415-0676 / 03.14.08

Download from Www.Somanuals.com. All Manuals Search And Download.

OPTIONAL BLOWER INSTALLATION

WARNING

INSTALLATION TO BE DONE BYAQUALIFIED INSTALLER and must be electrically connected and grounded in accordance with local codes.

In the absence of local codes, use the current CSA C22.1 CANADIAN ELECTRICAL CODE in Canada or the ANSI/NFPA 70 NATIONAL

ELECTRICAL CODE in the United States.

1. Turn off any electrical power to the ﬁreplace (if applicable). Open the lower louvred

control door.

2. Locate the vibration reducing pad over the two threaded studs, piercing 2 holes into

the pad. The fan must be installed on the left hand side of the ﬁreplace entirely on the pad.

3. Slide the fan to the back of the ﬁreplace taking care not to damage the terminals.

Position the fan onto the studs and secure using the lock washers and wing nuts provided.

Pull the leads to the front and right side of the ashpan housing.

4. Remove the junction box. Use a nut connector to attach the black wires of the variable

speed switch and the power.

5. Pass the two fan leads and one thermodisc lead through the junction box bushing.

FIGURE 32

The thermodisc is located inside the outer shell, just above the louvre door. Connect one fan

lead to the thermodisc lead and the other fan lead to the white wire of the variable speed

switch using nut connectors.

6. Thread the other thermodisc lead through the junction box bushing and connect to the white wire of the power cord using a nut

connector. Secure ground wire (green) to the threaded weld stud located on the junction box wall. Reposition the junction box. Verify that

the wires will not interfere with the fan.

BECAUSE THE BLOWER IS THERMALLY ACTIVATED, WHEN TURNED ON, IT WILL AUTOMATICALLY START APPROXIMATELY

15-45 MINUTES AFTER LIGHTING THE FIREPLACE. USE OF THE FAN INCREASES THE OUTPUT OF HEAT.

Drywall dust will penetrate into the blower bearings causing irreparable damage and must be prevented from coming into contact

with the blower or its compartment. Any damage resulting from this condition is not covered by the warranty policy.

FIGURE 33

BLOWER

WING NUT &

VIBRATION

THERMODISC

LOCK WASHER

REDUCING PAD

VARIABLE

SPEED

SWITCH

FAN

JUNCTION BOX

FEATURES

CONTROLLING COMBUSTION AIR

ACHIEVING PROPER DRAFT

Draft is the force which moves air from the ﬁreplace up through the

chimney. The amount of draft in your chimney depends on the length

of the chimney, local geography, nearby obstructions and other forces.

Adjusting the draft control regulates the temperature. The draft can

be adjusted from a low burn rate with the handle at the bottom setting

to a fast burn rate with the handle at the top setting. Inadequate draft

may cause back-pufﬁng into the room and may cause plugging of

the chimney. Too much draft may cause an excessive temperature

in the ﬁreplace, glowing red ﬁreplace parts or an uncontrollable burn

which can all lead to a chimney ﬁre or a permanent damage to the

unit. Do not operate your ﬁreplace for longer than 30 minutes

with the draft control on 'HIGH' (fully

WARNING

Fireplace operation does require air. Do not take air from other fuel

burning appliances which can result in improper venting (smoking)

or air dilution. Always provide adequate makeup air.

If the outside combustion air kit is not used, air may still be drawn

directly into the ﬁreplace through the lower louvres. Outside and

inside air may be combined by pulling the outside air lever out as far

as possible, and turning the lever 90° to its locking position.

Should you ﬁnd a frost build up on

from the ﬁreplace, close the outside

is not in use.

the air control box or a draft

air lever when the ﬁreplace

open).

Air control box

is shipped

with inside

a i r c o v e r

plate in open

position.

FIGURE 34

W415-0676 / 03.14.08

FIGURE 35

Download from Www.Somanuals.com. All Manuals Search And Download.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATING INSTRUCTIONS

Remove all source of gasoline or other ﬂammable vapours and

FUEL LOADING AND BURN CYCLE

liquids in the vicinity of this or other appliances prior to light-

ing. Ensure that the top ﬁrebricks and ﬁbre bafﬂes are in place

and not lifted up.

For maximum efﬁciency, when the ﬁreplace is thoroughly hot, load

it fully to the top of the door opening and burn at a medium low set-

ting. The bricks will be nearly all white and the glass mostly clear.

The whiteness of the bricks and the cleanness of the glass are good

indicators of your operating efﬁciency.

When ﬁrst installed, the ﬁreplace and the steel are cold and must

become hot before the ﬁreplace will function well. During the break-in

period (the ﬁrst 2 or 3 ﬁres) create only small, hot ﬁres using kindling;

this will allow the ﬁrebrick to cure. Do not be alarmed if small hairline

cracks develop in the ﬁrebrick. This is a normal occurrence and does

not pose a safety hazard. The paint may also smell a little for the

ﬁrst few ﬁres as it cures and you may wish to open a door or window

to alleviate the smell.

Not enough heat is produced when only one or two pieces of wood

are burned. A minimum of three pieces are needed to encase a bed

of coals that sustains the ﬁre. Loosely stacked wood burns quicker

than a tightly packed load.

Wood burns in cycles rather than giving a steady output of heat. It

is best to plan these cycles around your household routine so that

only enough coals are left to start the next load. In the evening, load

your ﬁreplace, at least, a half-hour before bed to ensure the ﬁre is hot

enough to close the draft control for an overnight burn.

Burn only dry seasoned wood. It produces more heat and less soot or

creosote. Do not burn ocean beach wood. Its salt content can produce

a metal eating acid. When refuelling open the door slowly to prevent

smoke spillage. Use a pair of long ﬁreplace gloves when feeding the

ﬁre. Keep a small steel shovel nearby to use as a poker and to remove

ashes. Do not store wood within 3 feet (1m) of the ﬁreplace.

To start, a brisk ﬁre is required. Place loosely crumpled paper on

the ﬂoor of the ﬁreplace behind the log retainer and cover with dry

kindling. Open the draft control fully by moving the lever to "HIGH".

Light the paper and leave the door slightly ajar (one inch) until all

kindling is burning. To maintain a brisk ﬁre, a hot coal bed must be

established and maintained.

Slowly add larger wood (2x4 size pieces). Lay the pieces lengthwise

from side to side in the hot coal bed with a shallow trench between,

so that the primary air can ﬂow directly into this trench and ignite the

fuel above. When the ﬁre seems to be at its peak, medium sized

logs may be added. Once these logs have caught ﬁre, carefully

close the door.

FLASH FIRES: A ﬂash ﬁre is a small ﬁre burned quickly when you

don't need much heat. After your kindling has "caught", load at least

3 pieces of wood, stacked loosely. Burn with the draft control fully

open or closed only slightly.

Closing the door too quickly after refuelling will reduce the ﬁre-

box temperature and result in an unsatisfactory burn.

Remember it is more efﬁcient to burn medium sized wood, briskly,

and refuel frequently than to load the ﬁreplace with large logs that

result in a smouldering, inefﬁcient ﬁre and dirty glass.

EXTENDED FIRE: Load your larger pieces of wood compactly,

packed close enough to prevent the ﬂames from penetrating it

completely. After approximately 30 minutes, depending on the size

of the load, close the draft control completely making sure that the

ﬁre is not extinguished.

As soon as the door is closed, you will observe a change in the ﬂame

pattern. The ﬂames will get smaller and lazier because less oxygen

is getting into the combustion chamber. The ﬂames, however, are

more efﬁcient. The ﬂames will remain lazy but become larger again

as soon as the ﬁrebricks have been heated thoroughly and the

chimney becomes heated and provides a good draft. At this point,

the roaring ﬁre that you see when the door is opened is wastefully

drawing heated room air up the chimney -- certainly not desirable.

So always operate with the door fully closed once the medium sized

logs have caught ﬁre.

DO NOT OVERFIRE THE FIREPLACE! Overﬁring can occur by:

a) burning large amounts of smaller wood pieces such as furniture

scraps, skids or treated wood; b) vigorously burning large loads of

wood with the draft control on "HIGH" (fully open) for long periods of

time (one or two hours).

You can now add larger pieces of wood and operate the ﬁreplace

normally. Once the ﬁreplace is entirely hot, it will burn very efﬁciently

with little smoke from the chimney. There will be a bed of orange

coals in the ﬁrebox and secondary ﬂames ﬂickering just below the

top of the ﬁrebox. You can safely ﬁll the ﬁrebox with wood to the top

of the door.

Can't get the stove operating? Use more kindling and paper.

Assuming the chimney and vent are sized correctly and there is

sufﬁcient combustion air, the lack of sufﬁciently dry quantities of

small kindling is the problem. Thumb size is a good gauge for small

kindling diameter.

WARNING

Do not store fuel within the clearance to combustibles, or in the

space required for re-fueling and ash removal.

Burning wet, unseasoned wood can cause excessive creosote

accumulation. When ignited it can cause a chimney ﬁre that may

result in a serious house ﬁre.

Never use gasoline-type lantern fuel, kerosene, charcoal lighter

ﬂuid, or similar liquids to start or "freshen up" a ﬁre in this ﬁreplace.

Keep all such liquids well away from the ﬁreplace.

Can't get heat out of the stove? One of two things may have hap-

pened. The ﬁreplace door may have been closed prematurely and

the ﬁreplace itself has not reached optimum temperature. Re-open

the door and/or draft control to re-establish a brisk ﬁre. The other

problem may have been wet wood. The typical symptom is sizzling

wood and moisture being driven from the wood.

WARNING

This ﬁreplace has not been tested with any vented or unvented

gas log set. To reduce risk of ﬁre or injury, do not install a vented

or unvented gas log set into ﬁreplace.

Always operate this appliance with the door closed and latched

except during start-up and re-fueling.

Do not leave the ﬁre unattended when the door is unlatched. Un-

stable ﬁrewood could fall out of the ﬁrebox creating a ﬁre hazard

to your home.

W415-0676 / 03.14.08

Download from Www.Somanuals.com. All Manuals Search And Download.

ASH REMOVAL PROCEDURES

A bed of ashes approximately 1" deep should be left on the ﬁrebox Never operate your ﬁreplace with the ash well in an open posi-

bottom to help maintain a hot charcoal bed. When the ﬁre has burned tion!

down and cooled, remove any excess ashes. To use your ash pan, pull

This creates a ﬁre hazard that may result in a house/chimney ﬁre,

the ash dump handle forward to an open position. Rake the excess

internal damage to the stove or discoloration to the gold plated door

ashes over the grate and into the ash pan. Close the ash well.

(plated ﬁnishes are not covered by the warranty). To ensure that

the ash well is fully closed, allow the door to snap shut, dislodging

anything that may be stuck at the opening.

Flip the cover up onto the ash pan when transporting the ashes to

a closed container with a tight ﬁtting lid for storage. Carry the ash

pan using the front and back handles. Keep the closed container on

a non-combustible ﬂoor or ground, well away from all combustible

FIGURE 36

materials. The ashes should be retained in the closed container until

all cinders have thoroughly cooled. Cold wood ashes can be used

on the garden or compost.

MAINTENANCE

GASKET / BAFFLE REPLACEMENT

At the end of each burning season inspect the bafﬂe located above

WARNING

the secondary air tubes for deterioration. Replace if necessary.At this

A chimney ﬁre can permanently damage your chimney system.

time also check that the door gasket is not worn or loose. Replace

This damage can only be repaired by replacing the damaged

with 1/2" ﬁbreglass rope if necessary.

component parts. Chimney ﬁres are not covered by the Limited

Lifetime Warranty.

DOOR GLASS REPLACEMENT

To remove the door, open and lift out; remove the screws and brackets

FIRE EXTINGUISHERS AND SMOKE

holding the glass in place. Remove all broken glass. Wrap the edges

of the new glass with a U-shaped strip of ﬁbreglass gasket, covering

DETECTORS

1/4" on each side. Place this gasketed glass in position and replace the

All homes with a solid fuel burning ﬁreplace should have at least

brackets and screws. When ﬁnished, you should be able to move the

one ﬁre extinguisher in a central location, known to all, and at least

glass slightly, horizontally and vertically.

one smoke detector in the room containing the ﬁreplace. If it sounds

an alarm, correct the cause but do not de-activate or relocate the

CREOSOTE FORMATION AND

smoke detector.

REMOVAL

WOODPILE MAINTENANCE

When wood is burned slowly, it produces tar and other organic

Burn only dry, clean unpainted wood that has been seasoned. It pro-

vapours which combine with expelled moisture to form creosote.

duces more heat and less soot or creosote. Freshly cut wood contains

These vapours condense in the relatively cooler chimney ﬂue of a

about 50% moisture while after proper seasoning only about 20% of

slow burning ﬁre and when ignited, make an extremely hot ﬁre. So,

the water remains. As wood is burned, this water boils off consuming

the chimney should be inspected monthly during the heating season

energy that should be used in heating. The wetter the wood, the less

to determine if a build-up has occurred. If creosote has accumulated

heat is given off and the more creosote is produced.

it should be removed to reduce the risk of a chimney ﬁre.

Both hardwood and softwood burn equally well in this ﬁreplace but

RUN-AWAY OR CHIMNEY FIRE

hardwood, which is denser, will weigh more per cord and burn a little

slower and longer. Firewood should be split, stacked in a manner that

air can get to all parts of it and covered in early spring to be ready for

burning that fall. Dry ﬁrewood has cracks in the end grain.

Run-away ﬁres can be the result of FOUR major factors:

1. Using incorrect fuel, or small fuel pieces which would normally be

used as kindling.

2. Leaving the door ajar too long and creating extreme temperatures

as the air rushes in the open door.

3. Burning your ﬁreplace with the ash dump door open.

4. Improperly installed or worn gaskets.

SOLUTIONS:

1. Do not burn treated or processed wood, coal, charcoal, coloured

paper or cardboard.

2. Be careful not to overﬁre the unit by leaving the door open too long

after the initial start-up.

3. Always operate the ﬁreplace with the ash well in a closed posi-

tion.

4. Replace worn, dried out (inﬂexible) gaskets.

WHAT TO DO IF A RUN-AWAY OR CHIMNEY FIRE STARTS:

1. Close the draft fully (lowest position).

2. Call the local ﬁre department.

3. Examine the chimney, attic and roof of the house, to see if any

part has become hot enough to catch ﬁre. If necessary spray with a

ﬁre extinguisher or water from a garden hose.

4. Do not operate the stove again until you are certain the chimney

has not been damaged.

W415-0676 / 03.14.08

REPLACEMENTS

Contact your dealer for questions concerning prices and avail-

ability of replacement parts. Normally all parts can be ordered

through your Authorized dealer or distributor.

When ordering replacement parts always give the following

information:

WARNING

Failure to position the parts in accordance with these diagrams or

failure to use only parts specified approved with this appliance may

result in property damage or personal injury.

1. M^ODEL& SERIAL NUMBER OF FIREPLACE

2. INSTALLATION DATE OF FIREPLACE

3. P^ARTNUMBER

4. D^{ESCRIPTION OF PART}

5. F^INISH

* IDENTIFIES ITEMS WHICH ARE NOT ILLUSTRATED.

FOR FURTHER INFORMATION, CONTACT YOUR

AUTHORIZED DEALER.

FOR WARRANTY REPLACEMENT PARTS, A PHOTO-

COPY OF THE ORIGINAL INVOICE WILL BE REQUIRED

TO HONOUR THE CLAIM.

REPLACEMENT PARTS

PART NO. DESCRIPTION

ACCESSORIES

PART NO.DESCRIPTION

W010-0243

W325-0028

W090-0044

W090-0045

W090-0039

W090-0042

W090-0043

W090-0041

W090-0040

ASH PAN WITH LID

22 111KT

OUTSIDE AIR KIT

ASH PAN HANDLE

23 NZ 690KT

24 NZ 62 CH*

25 NZ62*

26 NZ 220

27 GA-566

28 GA-70

THERMOSTATIC AIR CONTROL KIT

CENTRAL HEATING KIT

BLOWER KIT

RIGHT FRONT FIREBRICK

LEFT FRONT FIREBRICK

REAR FIREBRICK - 2 REQUIRED

BOTTOM RIGHT FIREBRICK

BOTTOM LEFT FIREBRICK

RIGHT SIDE FIREBRICK

LEFT SIDE FIREBRICK

LEFT UPPER FIREBRICK BAFFLE

RIGHT UPPER FIREBRICK BAFFLE

RIGHT FIBRE BAFFLE

LEFT FIBRE BAFFLE

HOT AIR GRAVITY VENT KIT - 5 FT.

HOT AIR DISTRIBUTION KIT

EXTENSION KIT - 5 ^FT

29 W175-0002* FLEXIBLE PIPE COUPLER - 8" DIA.

30 W010-0067* FLEXIBLE VENT SUPPORT ASSEMBLY

10 W090-0037

11 W090-0038

31 NZ-FTS*

32 NZ 220-2*

FLUE TILE SUPPORT ASSEMBLY

HOT AIR GRAVITY VENT EXTENSION KIT - 5 FT.

C/W INSULATION SLEEVE

12 W018-0063

13 W018-0064

14 KB35

15 W690-0002

16 W018-0060

17 W010-1072

18 W562-0010

19 W562-0016

20 W325-0007

21 W325-0002

33 W410-0005* 10FT FLEXIBLE ALUMINUM AIR VENT - 8" DIA.

VARIABLE SPEED CONTROL

HEAT SENSOR

BAFFLE SUPPORT

(FOR USE WITH NZ62CH)

34 H333

ARCHED BLACK DOOR C/W HANDLE & GASKET

ARCHED GOLD PLATED DOOR C/W HANDLE & GASKET

ARCHED STAINLESS STEEL DOOR C/W HANDLE & GASKET

WEBBED BLACK DOOR C/W HANDLE & GASKET

35 H333G

36 H333SS

37 H334

DOOR ^C/WGLASS & GASKET

DOOR GASKET

GLASS GASKET

37 H334G

37 H334SS

38 NZLPB

38 NZLK

38 NZLG

38 NZLSS

39 CFSK-B

40 AK-5

WEBBED GOLD PLATED DOOR C/W HANDLE & GASKET

WEBBED STAINLESS STEEL DOOR C/W HANDLE & GASKET

UPPER & LOWER LOUVRE ASSEMBLY- POLISHED BRASS

UPPER & LOWER LOUVRE ASSEMBLY - BLACK

UPPER & LOWER LOUVRE ASSEMBLY - GOLD PLATED

UPPER & LOWER LOUVRE ASSEMBLY - SATIN CHROME

CAST FIREPLACE SURROUND KIT

LARGE SPRING HANDLE

SMALL SPRING HANDLE

ADAPTER KIT, CAST SURROUND

W415-0676 / 03.14.08

Download from Www.Somanuals.com. All Manuals Search And Download.

Download from Www.Somanuals.com. All Manuals Search And Download.

W415-0676 / 03.14.08

TROUBLE SHOOTING GUIDE

BUILD YOUR FIRE ON THE FLOOR OF THE FIREBOX AND BE- Expansion / contraction noises during heating up and cooling down

HIND THE LOG RETAINER ONLY.

cycles are normal and to be expected. When ﬁrst lighting a ﬁre, if the

smoke is not quickly drawn into the chimney, there may be a downdraft

or cold air in the chimney. Roll up some newspaper, light it and place

it near the ﬁreplace ﬂue until the chimney begins to draw. During a

ﬁring, open the draft control before opening the ﬁreplace door. Open

the door slowly to avoid drawing smoke into the room.

Do not block or restrict the hot air outlets or air inlets. This will

cause the ﬁreplace to overheat.

Keep ﬁres away from the door.

A properly installed ﬁreplace should not smoke. If yours does, check

the following: Has the chimney had time to get hot? Is the smoke

passage blocked anywhere in the ﬁreplace or chimney? Is the room

too airtight and the air intake not connected to the outside? Check

with a window partly open. Is the smoke ﬂow impeded by too long a

horizontal pipe or too many bends? Is it a weak draft perhaps caused

by a leaky chimney, a cold outside chimney, too short a chimney, or

a chimney too close to trees or a higher roof?

DOs:

Build a hot ﬁre.

Use only dry wood

Several pieces of medium sized wood are better

than a few big pieces.

Clean the chimney regularly.

Refuel frequently using medium sized wood.

"Fine Tune" the air settings for optimum

performance.

MAINTENANCE

Check your chimney for creosote and soot build-up monthly until

a safe frequency for cleaning is established. If accumulation is

excessive, clean the chimney. You may want to call a professional

chimney sweep to clean it. Both the chimney and the ﬁreplace have

to be cleaned at least once a year or as often as necessary. See the

Section on Creosote Formation and Removal.

DON'Ts:

Take ash out immediately. Let it accumulate to

a depth of at least 1". A good ash layer

provides for a longer lasting and better burning

ﬁre.

Burn wet wood.

Close the door too soon or damper down too

quickly.

Burn one large log rather than two or three

smaller, more reasonably sized logs.

Burn at continually 'low setting', if the glass door

is constantly blackened. This means the ﬁrebox

temperature is too low.

W415-0676 / 03.14.08

Download from Www.Somanuals.com. All Manuals Search And Download.

W415-0676 / 03.14.08

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES

W415-0676 / 03.14.08

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES

W415-0676 / 03.14.08

Download from Www.Somanuals.com. All Manuals Search And Download.