NOTE: This product's firmware limits operation to only the channels allowed in a particular Region or Country.
Therefore, all options described in this user's guide may not be available in your version of the product.
Europe – EU Declaration of Conformity
Marking by the above symbol indicates compliance with the Essential Requirements of the R&TTE Directive of the
European Union (1999/5/EC). This equipment meets the following conformance standards:
EN300 328, EN301 489-17, EN60950
A printed copy of the EU Declaration of Conformity certificate for this product is provided in the
WNR3500L product package.
Europe – Declaration of Conformity in Languages of the European Community
Cesky [Czech]
NETGEAR Inc. tímto prohlašuje, že tento Radiolan je ve shode se základními
požadavky a dalšími príslušnými ustanoveními smernice 1999/5/ES.
Dansk
Undertegnede NETGEAR Inc. erklærer herved, at følgende udstyr Radiolan overholder
[Danish]
de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Deutsch
[German]
Hiermit erklärt NETGEAR Inc., dass sich das Gerät Radiolan in Übereinstimmung mit
den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der
Richtlinie 1999/5/EG befindet.
Eesti
Käesolevaga kinnitab NETGEAR Inc. seadme Radiolan vastavust direktiivi 1999/5/EÜ
[Estonian]
põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.
English
Hereby, NETGEAR Inc., declares that this Radiolan is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
Español
[Spanish]
Por medio de la presente NETGEAR Inc. declara que el Radiolan cumple con los
requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la
Directiva 1999/5/CE.
Ελληνική
[Greek]
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ NETGEAR Inc. ΔΗΛΩΝΕΙ ΟΤΙ Radiolan ΣΥΜΜΟΡΦΩΝΕΤΑΙ
ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ
ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
Français
[French]
Par la présente NETGEAR Inc. déclare que l'appareil Radiolan est conforme aux
exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.
Italiano [Italian] Con la presente NETGEAR Inc. dichiara che questo Radiolan è conforme ai requisiti
essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Latviski
Ar šo NETGEAR Inc. deklarē, ka Radiolan atbilst Direktīvas 1999/5/EK būtiskajām
[Latvian]
prasībām un citiem ar to saistītajiem noteikumiem.
Lietuvių
Šiuo NETGEAR Inc. deklaruoja, kad šis Radiolan atitinka esminius reikalavimus ir kitas
[Lithuanian]
1999/5/EB Direktyvos nuostatas.
iii
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
Nederlands
[Dutch]
Hierbij verklaart NETGEAR Inc. dat het toestel Radiolan in overeenstemming is met de
essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.
Malti [Maltese]
Hawnhekk, NETGEAR Inc., jiddikjara li dan Radiolan jikkonforma mal-htigijiet
essenzjali u ma provvedimenti ohrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.
Magyar
Alulírott, NETGEAR Inc. nyilatkozom, hogy a Radiolan megfelel a vonatkozó alapvetõ
[Hungarian]
követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.
Polski [Polish]
Niniejszym NETGEAR Inc. oświadcza, że Radiolan jest zgodny z zasadniczymi
wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.
Português
NETGEAR Inc. declara que este Radiolan está conforme com os requisitos essenciais
[Portuguese]
e outras disposições da Directiva 1999/5/CE.
Slovensko
[Slovenian]
NETGEAR Inc. izjavlja, da je ta Radiolan v skladu z bistvenimi zahtevami in ostalimi
relevantnimi določili direktive 1999/5/ES.
Slovensky
[Slovak]
NETGEAR Inc. týmto vyhlasuje, _e Radiolan spĺňa základné po_iadavky a všetky
príslušné ustanovenia Smernice 1999/5/ES.
Suomi
NETGEAR Inc. vakuuttaa täten että Radiolan tyyppinen laite on direktiivin 1999/5/EY
[Finnish]
oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.
Svenska
[Swedish]
Härmed intygar NETGEAR Inc. att denna Radiolan står I överensstämmelse med de
väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv
1999/5/EG.
Íslenska
Hér með lýsir NETGEAR Inc. yfir því að Radiolan er í samræmi við grunnkröfur og aðrar
[Icelandic]
kröfur, sem gerðar eru í tilskipun 1999/5/EC.
Norsk
NETGEAR Inc. erklærer herved at utstyret Radiolan er i samsvar med de
[Norwegian]
grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF.
FCC Requirements for Operation in the United States
FCC Information to User
This product does not contain any user serviceable components and is to be used with approved antennas only. Any
product changes or modifications will invalidate all applicable regulatory certifications and approvals.
FCC Guidelines for Human Exposure
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance of 20 cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
iv
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC Declaration Of Conformity
We NETGEAR, Inc., 350 E. Plumeria Drive, San Jose, CA 95134, declare under our sole responsibility that the model
WNR3500L RangeMax Wireless-N Gigabit Router with USB WNR3500L complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions:
•
•
This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.
FCC Radio Frequency Interference Warnings & Instructions
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following methods:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an electrical outlet on a circuit different from that which the radio receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
RangeMax Wireless-N Gigabit Router with USB
Tested to Comply
with FCC Standards
FOR HOME OR OFFICE USE
Modifications made to the product, unless expressly approved by NETGEAR, Inc., could void the user's right to operate
the equipment.
Maximum Wireless Signal Rate Derived from IEEE Standard 802.11 Specifications
Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic,
building materials and construction, and network overhead, lower actual data throughput rate.
v
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
Product and Publication Details
Model Number:
WNR3500L
Publication Date:
Product Family:
November 2009
Wireless Router
Product Name:
RangeMax Wireless-N Gigabit Router with USB WNR3500L
Home or Business Product:
Language:
Home
English
Publication Part Number:
202-10545-01
vi
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Contents
NETGEAR RangeMax™ Wireless-N Gigabit Router with USB
About This Manual
Chapter 1
Using the Setup Manual .................................................................................................1-1
Selecting a Language for Your Screen Display ..............................................................1-5
Viewing or Manually Configuring Your ISP Settings .......................................................1-6
Chapter 2
Planning Your Wireless Network ....................................................................................2-1
Manually Configuring Your Wireless Settings .................................................................2-4
Contents
vii
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Chapter 3
Protecting Access to Your WNR3500v2 Router .............................................................3-1
Blocking Access to Internet Sites ...................................................................................3-4
Blocking Access to Internet Services .............................................................................3-6
Scheduling Blocking .......................................................................................................3-8
Configuring E-mail Alert and Web Access Log Notifications ........................................3-10
Setting the Time ............................................................................................................3-11
Chapter 4
Upgrading the Router Firmware .....................................................................................4-1
Erasing the Configuration .......................................................................................4-11
Enabling Remote Management Access .......................................................................4-11
Chapter 5
Using the LAN IP Setup Options ....................................................................................5-1
Configuring the WAN Setup Options ..............................................................................5-7
Allowing Inbound Connections to Your Network ...........................................................5-11
Contents
viii
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
How Port Forwarding Differs from Port Triggering .................................................5-15
Wireless Repeating (Also Called WDS) .......................................................................5-21
Wireless Repeating Function .................................................................................5-22
Setting Up the Base Station ...................................................................................5-23
Setting Up a Repeater Unit ....................................................................................5-24
Chapter 6
Assessing Your Speed Requirements ............................................................................6-2
Optimizing Your Network Bandwidth ..............................................................................6-3
Optimizing Wireless Performance ..................................................................................6-5
Changing the MTU Size .................................................................................................6-6
Quality of Service ...........................................................................................................6-7
Using Universal Plug and Play .....................................................................................6-13
Chapter 7
USB Drive Requirements ...............................................................................................7-1
File Sharing Scenarios ...................................................................................................7-2
Configuring USB Storage Advanced Settings ................................................................7-7
Creating a Network Folder .......................................................................................7-9
Unmounting a USB Drive .............................................................................................7-10
Specifying Approved USB Devices ...............................................................................7-11
Locating the Internet Port IP Address ....................................................................7-12
Contents
ix
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Connecting to the USB Drive with Microsoft Network Settings ....................................7-12
Enabling File and Printer Sharing ..........................................................................7-13
Chapter 8
Cannot Access the Internet ............................................................................................8-6
Testing the LAN Path to Your Router .......................................................................8-8
Wireless Connectivity ...................................................................................................8-10
Using Your Wireless Card Setup Program .............................................................8-11
Setting Up and Testing Basic Wireless Connectivity ..............................................8-11
Appendix A
Technical Specifications ................................................................................................. A-3
Appendix B
Contents
x
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Manual
®
This user manual provides information for configuring the features of the NETGEAR
RangeMax Wireless-N Gigabit Router with USB WNR3500L beyond initial configuration
settings. Initial configuration instructions can be found in the NETGEAR Wireless Router Setup
Manual. The information in this manual is intended for readers with intermediate computer and
Internet skills.
Conventions, Formats, and Scope
The conventions, formats, and scope of this manual are described in the following paragraphs:
•
Typographical conventions. This manual uses the following typographical conventions:
Italic
Emphasis, books, CDs
User input, GUI screen text
Command prompt, CLI text, code
URL links
Bold
Fixed
Italic
•
Formats. This manual uses the following formats to highlight special messages:
Note: This format is used to highlight information of importance or special interest.
Tip: This format is used to highlight a procedure that will save time or resources.
Warning: Ignoring this type of note might result in a malfunction or damage to the
equipment, a breach of security, or a loss of data.
xi
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Danger: This is a safety warning. Failure to take heed of this notice might result in
personal injury or death.
•
Scope. This manual is written for the WNR3500L router according to these specifications:
Product Version
RangeMax Wireless-N Gigabit Router with USB WNR3500L
November 2009
Manual Publication Date
For more information about network, Internet, firewall, and VPN technologies, click the links to
Note: Product updates are available on the NETGEAR, Inc. website at
How to Print This Manual
To print this manual, your computer must have the free Adobe Acrobat reader installed in order to
view and print PDF files. The Acrobat reader is available on the Adobe Web site at
Tip: If your printer supports printing two pages on a single sheet of paper, you can
save paper and printer ink by selecting this feature.
Revision History
Version
Number
Part Number
Date
Description
202-10433-01
202-10545-01
1.0
1.0
May 2009
First publication.
New features.
November 2009
xii
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Configuring Your Internet Connection
This chapter describes how to configure your WNR3500L router Internet connection. When you
install your wireless router using the Resource CD as described in the NETGEAR Router Setup
Manual, these settings are configured automatically for you. This chapter provides instructions on
how to log in to the wireless router for further configuration.
Note: NETGEAR recommends using the Smart Wizard™ on the Resource CD for initial
configuration, as described in the NETGEAR Wireless Router Setup Manual.
This chapter includes the following sections:
•
•
•
•
•
Using the Setup Manual
For first-time installation of your wireless router, refer to the NETGEAR Wireless Router Setup
Manual. The Setup Manual explains how to launch the NETGEAR Smart Wizard on the Resource
CD to step you through the procedure to connect your router, modem, and computers. The Smart
Wizard will assist you in configuring your wireless settings and enabling wireless security for your
network. After initial configuration using the Setup Manual, you can use the information in this
User Manual to configure additional features of your wireless router.
For installation instructions in a language other than English, refer to the language options on the
Resource CD.
1-1
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Logging In to Your Wireless Router
You can log in to the wireless router to view or change its settings.
Note: Your computer must be configured for DHCP. For help with configuring DHCP, see
the documentation that came with your computer or see the link to the online
To log in to the wireless router:
1. Connect to the wireless router by typing http://www.routerlogin.net or the router’s LAN IP
address (the default is 192.168.1.1) in the address field of your browser, and then press Enter.
A login window opens:
Figure 1-1
Tip: You can connect to the wireless router by typing either of these URLs in the
address field of your browser, and then pressing Enter:
If these URLs do not work, you must type the IP address of the router, for
example, http://www.192.168.1.1.
Configuring Your Internet Connection
1-2
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
2. Enter admin for the router user name and your password (or the default, password). For
information about how to change the password, see “Changing the Built-In Password” on
Note: The router user name and password are not the same as any other user name or
password you might use to log in to your Internet connection.
The Checking for Firmware Updates screen displays unless you previously cleared the Check
for Updated Firmware Upon Log-in check box.
Figure 1-2
If the router discovers a newer version of software, you are asked if you want to upgrade to the
firmware is available, the following message displays.
Figure 1-3
3. The Basic Settings screen displays showing the wireless router’s settings.
Configuring Your Internet Connection
1-3
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Figure 1-4
Note: If the Check for New Version Upon Log-in check box is selected, the home
page is the Router Upgrade screen. Otherwise, it is the Basic Settings screen.
If the wireless router is connected to the Internet, you can select Knowledge Base or
Documentation under Web Support in the main menu to view support information or the
documentation for the wireless router.
If you do not click Logout, the wireless router will wait for 5 minutes after no activity before
it automatically logs you out.
Configuring Your Internet Connection
1-4
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Using the Setup Wizard
You can manually configure your Internet connection using the Basic Settings screen, or you can
allow the Setup Wizard to determine your Internet Service Provider (ISP) configuration.
The Setup Wizard searches your Internet connection for servers and protocols to determine your
ISP configuration. This feature is not the same as the Smart Wizard on the Resource CD. To use
the Setup Wizard to assist with configuration or to verify the Internet connection settings:
1. From the main menu, select Setup Wizard.
2. Click Next to proceed. Enter your ISP settings, as needed.
3. At the end of the Setup Wizard, click Test to verify your Internet connection. If you have
Viewing or Manually Configuring Your ISP Settings
To view or configure the basic settings:
2. Select Yes or No depending on whether your ISP requires a login. This selection changes the
fields available on the Basic Settings screen.
•
•
Yes. If your ISP requires a login, select the encapsulation method. Enter the login name. If
you want to change the login time-out, enter a new value in minutes.
No. If your ISP does not require a login, enter the account name, if required, and the
domain name, if required.
3. Enter the settings for the IP address and DNS server. If you enter or change a DNS address,
restart the computers on your network so that these settings take effect.
4. If no login is required, you can specify the MAC Address setting.
5. Click Apply to save your settings.
6. Click Test to test your Internet connection. If the NETGEAR website does not appear within
Configuring Your Internet Connection
1-5
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
When your Internet connection is working you do not need to launch the ISP’s login program on
your computer to access the Internet. When you start an Internet application, your wireless router
automatically logs you in
The fields that are displayed depend on whether or not your Internet connection requires a login.
ISP does not require login
ISP does require login
Figure 1-5
The following table explains the fields in the Basic Settings screen.
Configuring Your Internet Connection
1-6
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Table 1-1. Basic Settings screen fields
Settings
Description
Does Your ISP Require a Login?
• Yes
• No
These fields
appear only if no (If required)
Account Name
Enter the account name provided by your ISP. This might also
be called the host name.
login is required.
Domain Name
Enter the domain name provided by your ISP.
(If required)
These fields
appear only if
your ISP
Internet Service Provider • PPTP (Point to Point Tunneling Protocol). This is used
primarily in Austrian DSL services.
• Telstra Bigpond. This setting is only for older cable modem
service accounts that still require a Bigpond Login utility.
Telstra has discontinued this type of account. Those with
Telstra DSL accounts and newer cable modem accounts
should select No for Does Your Internet Connection
Require A Login?.
requires a login.
• Other. This is the default setting. It is for PPPoE (Point to
Point Protocol over Ethernet), the protocol used by most
DSL services worldwide.
Login
The login name provided by your ISP. This is often an e-mail
address.
Password
The password that you use to log ISP.
Service Name
If your ISP provided a Service Name, enter it here. This field
appears if the Internet Service Provider is defined as “Other”
(PPPoE)
Connection Mode
Specify when the router will connect to and disconnect from
the Internet.
• Always On. The router logs in to the Internet immediately
after booting and never disconnects.
• Dial on Demand. The router logs in only when outgoing
traffic is present and logs out after the idle time-out.
• Manually Connect. The router logs in or logs out only when
you click Connect or Disconnect in the Router Status
screen.
Idle Timeout (In minutes) If you want to change the Internet login time-out, enter a new
value in minutes. This determines how long the wireless router
keeps the Internet connection active after there is no Internet
activity from the LAN. Entering an Idle Timeout value of 0
(zero) means never log out.
Configuring Your Internet Connection
1-7
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Table 1-1. Basic Settings screen fields (continued)
Settings
Description
Internet IP Address
• Get Dynamically from ISP. Your ISP automatically assigns
these addresses.
• Use Static IP Address. Enter the IP address that your ISP
assigned. Also enter the IP subnet mask and the gateway IP
address. The gateway is the ISP’s gateway to which your
wireless router will connect.
Domain Name Server (DNS) Address
The DNS server is used to look up site addresses based on
their names.
• Get Automatically from ISP. Your ISP automatically
assigns this address.
• Use These DNS Servers. If you know that your ISP does
not automatically transmit DNS addresses to the wireless
router during login, select this option, and enter the IP
address of your ISP’s primary DNS server. If a secondary
DNS server address is available, enter it also.
This field
Router MAC Address
The Ethernet MAC address that will be used by the wireless
router on the Internet port. Some ISPs register the Ethernet
MAC address of the network interface card in your computer
when your account is first opened. They will then accept traffic
only from the MAC address of that computer. This feature
allows your wireless router to masquerade as that computer
by “cloning” its MAC address.
appears if no
login is required
or the Internet
ServiceProvider
is not defined as
“Other.”
• Use Default Address. Use the default MAC address.
• Use Computer MAC Address. The wireless router will
capture and use the MAC address of the computer that you
are now using. You must be using the one computer that is
allowed by the ISP.
• Use This MAC Address. Enter the MAC address that you
want to use.
Configuring Your Internet Connection
1-8
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
Safeguarding Your Network
For a wireless connection, the SSID, also called the wireless network name, and the wireless
security setting must be the same for the wireless router and wireless computers or wireless
adapters. NETGEAR strongly recommends that you use wireless security.
Warning: Computers can connect wirelessly at a range of several hundred feet. This can
allow others outside of your immediate area to access your network.
This chapter includes:
•
•
•
•
•
Planning Your Wireless Network
For compliance and compatibility between similar products in your area, the operating channel
and region must be set correctly.
To configure the wireless network, you can either specify the wireless settings, or you can use Wi-
Fi Protected Setup (WPS) to automatically set the SSID and implement WPA/WPA2 security.
•
To manually configure the wireless settings, you must know the following:
–
–
–
SSID. The default SSID for the wireless router is NETGEAR.
The wireless mode (802.11n, 802.11g, or 802.11b) that each wireless adapter supports.
Wireless security option. To successfully implement wireless security, check each wireless
adapter to determine which wireless security option it supports.
2-1
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
•
Push 'N' Connect (WPS) automatically implements wireless security on the wireless router
while, at the same time, allowing you to automatically implement wireless security on any
WPS-enabled devices (such as wireless computers and wireless adapter cards). You activate
WPS by pressing a WPS button on the wireless router, clicking an onscreen WPS button, or
entering a PIN number. This generates a new SSID and implements WPA/WPA2 security.
Note: NETGEAR’s Push 'N' Connect feature is based on the Wi-Fi Protected Setup
Fi-certified and WPS-capable products should be compatible with NETGEAR
products that implement Push 'N' Connect.
To set up your wireless network using the WPS feature:
–
Use the WPS button on the side of the wireless router (there is also an onscreen WPS
button), or enter the PIN of the wireless device.
–
Make sure that all wireless computers and wireless adapters on the network are Wi-Fi
certified and WPA or WPA 2 capable, and that they support WPS configuration.
Wireless Placement and Range Guidelines
The range of your wireless connection can vary significantly based on the physical placement of
the wireless router. The latency, data throughput performance, and notebook power consumption
of wireless adapters also vary depending on your configuration choices.
For best results, place your wireless router according to the following guidelines:
•
•
Near the center of the area in which your PCs will operate.
In an elevated location such as a high shelf where the wirelessly connected PCs have line-of-
sight access (even if through walls).
•
Away from sources of interference, such as PCs, microwave ovens, and 2.4 GHz cordless
phones.
•
•
Away from large metal surfaces.
If using multiple access points, it is better if adjacent access points use different radio
frequency channels to reduce interference. The recommended channel spacing between
adjacent access points is 5 channels (for example, use Channels 1 and 6, or 6 and 11).
The time it takes to establish a wireless connection can vary depending on both your security
settings and placement.
Safeguarding Your Network
2-2
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Wireless Security Options
Computers can connect over a 802.11g or 802.11n network at a range of up to 300 feet. Such
distances can allow for others outside your immediate area to access your network.
Unlike wired network data, your wireless data transmissions can extend beyond your walls and
can be received by anyone with a compatible adapter. For this reason, use the security features of
your wireless equipment. The WNR3500L router provides highly effective security features which
are covered in detail in this chapter. Deploy the security features appropriate to your needs.
There are several ways you can enhance the security of your wireless network:
1. Open system: Easy, but
no security
2. WEP: Security, but some
performance impact
3. WPA-PSK: Strong security
4. WPA-2-PSK: Very strong
security
Figure 2-1
•
WEP. Wired Equivalent Privacy (WEP) data encryption provides data security. WEP Shared
Key authentication and WEP data encryption block all but the most determined eavesdropper.
This data encryption mode has been superseded by WPA-PSK and WPA2-PSK.
•
WPA-PSK (TKIP), WPA2-PSK (AES). Wi-Fi Protected Access (WPA) using a pre-shared
key to perform authentication and generate the initial data encryption keys. The very strong
authentication along with dynamic per frame re-keying of WPA makes it virtually impossible
to compromise.
For more information about wireless technology, see the link to the online document in “Wireless
Safeguarding Your Network
2-3
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Manually Configuring Your Wireless Settings
You can view or manually configure the wireless settings for the wireless router in the Wireless
Settings screen. If you want to make changes, make sure to note the current settings first.
Note: If you use a wireless computer to change the wireless network name (SSID) or
wireless security settings, you will be disconnected when you click Apply. To
avoid this problem, use a computer with a wired connection to access the wireless
router.
To view or manually configure the wireless settings:
1. Log in to the wireless router at its default LAN address of http://www.routerlogin.net with
its default user name of admin, and default password of password, or using whatever user
name, password, and LAN address you have chosen for the wireless router.
2. Select Wireless Settings from the main menu to display the Wireless Settings screen:
Figure 2-2
3. Select the region in which the wireless router will operate.
4. For initial configuration and test, leave the other settings unchanged.
5. To save your changes, click Apply.
Safeguarding Your Network
2-4
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
6. Configure and test your computers for wireless connectivity.
Program the wireless adapter of your computers to have the same SSID and wireless security
settings as your wireless router. Check that they have a wireless link and are able to obtain an
IP address by DHCP from the wireless router. If there is interference, adjust the channel.
Table 2-1. Wireless Settings
Settings
Description
Wireless
Network
Name (SSID): The SSID is also known as the wireless network name. Enter a 32-
character (maximum) name in this field. This field is case-sensitive.
In a setting where there is more than one wireless network, different wireless network
names provide a means for separating the traffic. Any device you want to participate
in a wireless network must use the SSID.
Region: The location where the router is used.
Channel: The wireless channel used by the gateway. The default is Auto.
Do not change the wireless channel unless you experience interference (shown by
lost connections or slow data transfers). If this happens, you might need to
experiment with different channels to see which is the best.
Mode: The default is up to 145 Mbps, which allows 802.11n, 802.11g, and 802.11b
wireless stations access.
Security Options • None. You can use this setting to establish wireless connectivity before
implementing wireless security. NETGEAR strongly recommends that you
implement wireless security.
• WEP (Wired Equivalent Privacy). Use encryption keys and data encryption for
data security. You can select 64-bit or 128-bit encryption.
• WPA-PSK [TKIP] (WiFi Protected Access Pre-Shared Key). Allow only
computers configured with WPA to connect to the wireless router.
• WPA2-PSK [AES] (Wi-Fi Protected Access with 2 Pre-Shared Keys). Allow only
computers configured with WPA2 to connect to the wireless router.
• WPA-PSK [TKIP] + WPA2-PSK [AES]. Allow computers configured with either
WPA-PSK or WPA2-PSK security to connect to the wireless router.
Safeguarding Your Network
2-5
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Configuring WEP Wireless Security
Note: If you use a wireless computer to configure wireless security settings, you will be
disconnected when you click Apply. Reconfigure your wireless computer to match
the new settings, or access the wireless router from a wired computer to make
further changes.
To configure WEP data encryption:
1. Log in to the wireless router at its default LAN address of http://www.routerlogin.net with
its default user name of admin, and default password of password, or using whatever user
name, password, and LAN address you have chosen for the wireless router.
2. From the main menu, select Wireless Settings to display the Wireless Settings screen.
3. In the Security Options section, select the WEP (Wired Equivalent Privacy) radio button:
Figure 2-3
4. Select the Authentication Type: Automatic or Shared Key. The default is Automatic.
Note: The authentication scheme is separate from the data encryption. If you require
strong security, use both the Shared Key and WEP encryption settings.
Safeguarding Your Network
2-6
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
5. Select the Encryption Strength setting:
•
WEP (Wired Equivalent Privacy) 64-bit encryption. Enter 10 hexadecimal digits (any
combination of 0–9, a–f, or A–F).
•
WEP (Wired Equivalent Privacy) 128-bit encryption. Enter 26 hexadecimal digits (any
combination of 0–9, a–f, or A–F).
6. Enter the encryption keys. You can manually or automatically program the four data
encryption keys. These values must be identical on all computers and Access Points in your
network:
•
Passphrase. To use a passphrase to generate the keys, enter a passphrase, and click
Generate. This automatically creates the keys. Wireless stations must use the passphrase
or keys to access the wireless router.
Note: Not all wireless adapters support passphrase key generation.
•
Key 1 – Key 4. These values are not case-sensitive. You can manually enter the four data
encryption keys. These values must be identical on all computers and access points in your
network. Enter 10 hexadecimal digits (any combination of 0–9, a–f, or A–F) for WEP-64
and 26 hexadecimal digits for WEP-128.
7. Select which of the four keys will be the default.
Data transmissions are always encrypted using the default key. The other keys can be used
only to decrypt received data. The four entries are disabled if WPA-PSK or WPA
authentication is selected.
8. Click Apply to save your settings.
Safeguarding Your Network
2-7
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Configuring WPA, WPA2, or WPA/WPA2 Wireless Security
To set up wireless security, you can either manually configure it in the Wireless Settings screen, or
you can use Wi-Fi Protected Setup (WPS) to automatically set the SSID and implement WPA/
Both WPA and WPA2 provide strong data security. WPA with TKIP is a software implementation
that can be used on Windows systems with Service Pack 2 or later; WPA2 with AES is a hardware
implementation; see your device documentation before implementing it. Consult the product
documentation for your wireless adapter for instructions for configuring WPA settings.
Note: If you use a wireless computer to configure wireless security settings, you will be
disconnected when you click Apply. If this happens, reconfigure your wireless
computer to match the new settings, or access the wireless router from a wired
computer to make further changes.
To configure WPA or WPA2 in the wireless router:
1. Log in to the wireless router at its default LAN address of http://www.routerlogin.net with
its default user name of admin and default password of password, or using whatever user
name, password, and LAN address you have chosen for the wireless router.
2. Select Wireless Settings from the main menu.
3. On the Wireless Settings screen, select the radio button for the WPA or WPA2 option of your
choice.
Figure 2-4
Safeguarding Your Network
2-8
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
4. The settings displayed on the screen depend on which security option you select.
5. For WPA-PSK or WPA2-PSK, enter the passphrase.
6. To save your settings, click Apply.
Using Push ‘N’ Connect to Configure Your Wireless Network
If your wireless clients support Wi-Fi Protected Setup (WPS), you can use this feature to configure
the wireless router’s SSID and security settings and, at the same time, connect the wireless client
securely and easily to the wireless router. Look for the
symbol on your client device
(computers that will connect wirelessly to the wireless router are clients). WPS automatically
configures the network name (SSID) and wireless security settings for the wireless router (if the
wireless router is in its default state) and transmits these settings to the wireless client.
Note: NETGEAR’s Push 'N' Connect feature is based on the Wi-Fi Protected Setup
certified and WPS-capable products should be compatible with NETGEAR
products that implement Push 'N' Connect.
Some considerations regarding WPS are:
•
WPS supports non-security, WPA-PSK, WPA2-PSK, and WEP with auto or open
authentication. WEP with Shared Key authentication is not supported.
•
If your wireless network will include a combination of WPS capable devices and non-WPS
capable devices, NETGEAR suggests that you set up your wireless network and security
settings manually first, and use WPS only for adding additional WPS capable devices. See
A WPS client can be added using the Push Button method or the PIN method.
•
•
Safeguarding Your Network
2-9
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Using the WPS Button to Configure Your Network and Add a
Client
Any wireless computer or wireless adapter that will connect to the wireless router wirelessly is a
client. The client must support a WPS button, and must have a WPS configuration utility, such as
the NETGEAR Smart Wizard or Atheros Jumpstart.
To use the wireless router WPS button to add a WPS client:
1. Log in to the wireless router at its default LAN address of http://www.routerlogin.net with
its default user name of admin and default password of password, or using whatever LAN
address and password you have set up.
2. On the wireless router main menu, select Add a WPS Client, and then click Next. The
following screen displays:
WPS button
Figure 2-5
By default, the Push Button (recommended) radio button is selected.
3. Either press the WPS button on the side of the wireless router, or click the onscreen button.
The wireless router tries to communicate with the client for 2 minutes.
4. Go to the client wireless computer, and run a WPS configuration utility. Follow the utility’s
instructions to click a WPS button.
5. Go back to the wireless router screen to check for a message.
Safeguarding Your Network
2-10
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
The wireless router WPS screen displays a message confirming that the client was added to the
wireless network. The wireless router generates an SSID, and implements WPA/WPA2
wireless security if the wireless settings on the router are not configured. The wireless router
will keep these wireless settings unless you change them, or you clear the Keep Existing
Wireless Settings check box in the WPS Settings screen.
Figure 2-6
6. Note the new SSID and WPA/WPA2 passphrase for the wireless network. You can view these
WPA/WPA2 Wireless Security” section.
To access the Internet from any computer connected to your wireless router, launch a browser such
as Microsoft Internet Explorer or Mozilla Firefox. You should see the wireless router’s Internet
LED blink, indicating communication to the ISP.
Note: If no WPS-capable client devices are located during the 2-minute timeframe, the
SSID and security settings will not be changed.
Using a PIN to Configure Your Network and Add a Client
Any wireless computer or wireless adapter that will connect to the wireless router wirelessly is a
client. The client must support a WPS PIN, and must have a WPS configuration utility, such as the
NETGEAR Smart Wizard or Atheros Jumpstart.
The first time you add a WPS client, make sure that the Keep Existing Wireless Settings check
box on the WPS Settings screen is cleared. This is the default setting for the wireless router, and
allows it to generate the SSID and WPA/WPA2 security settings when it implements WPS. After
WPS is implemented, the wireless router automatically selects this check box so that your SSID
and wireless security settings remain the same if other WPS-enabled devices are added later.
Safeguarding Your Network
2-11
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
To use a PIN to add a WPS client:
1. Log in to the wireless router at its default LAN address of http://www.routerlogin.net with
its default user name of admin and default password of password, or using whatever LAN
address and password you have set up.
2. On the wireless router main menu, select Add a WPS Client (computers that will connect
wirelessly to the wireless router are clients), and then click Next. The Add WPS Client screen
displays:
Figure 2-7
3. Select the PIN Number radio button.
4. Go to the client wireless computer. Run a WPS configuration utility. Follow the utility’s
instructions to generate a PIN. Take note of the client PIN.
5. From the wireless router Add WPS Client screen, enter the client PIN number, and then click
Next.
•
•
The wireless router tries to communicate with the client for 4 minutes.
The wireless router WPS screen displays a message confirming that the client was added
to the wireless network. The wireless router generates an SSID, and implements WPA/
WPA2 wireless security if the wireless settings on the router are not configured.
6. Note the new SSID and WPA/WPA2 passphrase for the wireless network. You can view these
WPA/WPA2 Wireless Security” section.
Safeguarding Your Network
2-12
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
To access the Internet from any computer connected to your wireless router, launch a browser such
as Microsoft Internet Explorer or Mozilla Firefox. You should see the wireless router’s Internet
LED blink, indicating communication to the ISP.
Note: If no WPS-capable client devices are located during the 4-minute timeframe, the
SSID and security settings will not be changed.
Configuring Advanced WPS Settings
From the main menu, select Advanced Wireless Settings to display the following screen:
Figure 2-8
The WPS settings show the wireless router PIN, Disable Router’s PIN, and the Keep Existing
Wireless Settings check box.
By default, the Keep Existing Wireless Settings check box is cleared. This allows the wireless
router to automatically generate the SSID and WPA/WPA2 security settings when it implements
WPS. After WPS is implemented, the wireless router automatically selects this check box so that
your SSID and wireless security settings remain the same if you add WPS-enabled devices or if
you manually add non WPS-capable devices later.
Note: If you clear the Keep Existing Wireless Settings check box, all wireless settings
and connections will be lost.
Safeguarding Your Network
2-13
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Adding Both WPS-Capable Clients and Non-WPS-Capable
Clients
If you have a wireless network with both WPS-capable clients and non-WPS-capable clients, you
should set up your wireless network manually. Then, use Push ‘N’ Connect (WPS) to quickly and
easily add additional WPS-capable clients.
Note: Your wireless settings remain the same when you add another WPS-enabled client,
as long as the Keep Existing Wireless Settings checkbox is selected in the
Advanced Wireless screen (listed under the Advanced heading in the wireless
router main menu). If you clear this checkbox, when you add the client, a new
SSID and passphrase will be generated, and all existing connected wireless clients
will be disassociated and disconnected from the wireless router.
To add a wireless client device that is WPS-enabled:
1. Log in to the wireless router at its default LAN address of http://www.routerlogin.net with
its default user name of admin and default password of password, or using whatever LAN
address and password you have set up.
2. On the wireless router main menu, select Add a WPS Client (computers that will connect
wirelessly to the wireless router are clients), and then click Next. The Add WPS Client screen
displays.
3. By default, the WPS button is selected. Either click the onscreen button, or press the WPS
button on the side of the wireless router.
The wireless router tries to communicate with the client for 2 minutes.
4. Go to the client wireless computer, and run a WPS configuration utility. Follow the utility’s
instructions to click a WPS button.
5. Go back to the wireless router screen to check for a message. The wireless router WPS screen
will display a message confirming that the client was added to the wireless network.
To view a list of all devices connected to your wireless router (including wireless and Ethernet-
To connect a non-WPS enabled client to the wireless router:
1. On the device you want to connect to the router, open the networking utility.
Safeguarding Your Network
2-14
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
2. Follow the utility’s instructions to enter the SSID (name you selected for your router).
3. Select the security type you selected for your router, and enter the security passphrase that you
entered for your router.
Note: NETGEAR recommends selecting either WPA/PSK, WPA2/PSK, or a mixed
network of both WPA/PSK and WPA2/PSK.
4. Click Enter.
5. Select your wireless network and click Connect.
To view a list of all devices connected to your wireless router (including wireless and
Restricting Access to Your Router
You can use the Advanced Wireless Settings screen to enable or disable the wireless router and the
SSID broadcast. From the main menu, select Advanced Wireless Settings to display the
following screen:
Figure 2-9
Safeguarding Your Network
2-15
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
•
•
Enable Wireless Router Radio.
You can completely turn off the wireless portion of the wireless router. For example, if you use
your notebook computer to wirelessly connect to your wireless router, and you take a business
trip, you can turn off the wireless portion of the wireless router while you are traveling. Other
members of your household who use computers connected to the wireless router via Ethernet
cables can still use the wireless router. To do this, clear the Enable Wireless Access Point
check box on the Advanced Wireless Settings screen, and then click Apply.
Enable SSID Broadcast. Clear this check box to disable broadcast of the SSID, so that only
devices that know the correct SSID can connect. Disabling SSID broadcast nullifies the
wireless network discovery feature of some products such as Windows XP.
Note: The SSID of any wireless access adapters must match the SSID you configure
in the wireless router. If they do not match, you will not get a wireless
connection to the wireless router.
The Fragmentation Threshold, CTS/RTS Threshold, and Preamble Mode options are reserved
for wireless testing and advanced configuration only. Do not change these settings.
•
•
Restricting access by MAC address. You can use a Wireless Card Access List to restrict
Safeguarding Your Network
2-16
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Protecting Your Network
This chapter includes the following sections:
•
•
•
•
•
•
•
•
Protecting Access to Your WNR3500L Router
For security reasons, the wireless router has its own user name and password. Also, after a period
of inactivity for a set length of time, the administrator login automatically disconnects. When
prompted, enter admin for the wireless router user name and password for the wireless router
password. You can use procedures in the following sections to change the wireless router password
and the amount of time for the administrator’s login time-out.
Note: The user name and password are not the same as a user name or password you
might use to log in to your Internet connection.
NETGEAR recommends that you change this password to a more secure password. The ideal
password should contain no dictionary words from any language, and should be a mixture of both
upper and lower case letters, numbers, and symbols. Your password can be up to 30 characters.
3-1
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Changing the Built-In Password
1. Log in to the wireless router at its default LAN address of http://www.routerlogin.net with
its default user name of admin, default password of password, or using whatever password
and LAN address you have chosen for the wireless router.
Figure 3-1
2. From the main menu, under the Maintenance heading, select Set Password to display the Set
Password screen:
Figure 3-2
3. To change the password, first enter the old password, and then enter the new password twice.
4. Click Apply to save your changes.
Note: After changing the password, you must log in again to continue the
configuration. If you have backed up the wireless router settings previously,
you should do a new backup so that the saved settings file includes the new
password.
Protecting Your Network
3-2
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Restricting Access by MAC Address
For increased security, you can restrict access to the wireless network to allow only specific PCs
based on their MAC addresses. You can restrict access to only trusted PCs so that unknown PCs
cannot wirelessly connect to the WNR3500L router. MAC address filtering adds an obstacle
against unwanted access to your network, but the data broadcast over the wireless link is fully
exposed.
To restrict access based on MAC addresses:
1. Log in to the wireless router at its default LAN address of http://www.routerlogin.net with
its default user name of admin, and default password of password, or using whatever user
name, password, and LAN address you have chosen for the wireless router.
Note: If you configure the router from a wireless computer, add your computer’s
MAC address to the access list. Otherwise you will lose your wireless
connection when you click Apply. You must then access the wireless router
from a wired computer, or from a wireless computer that is on the access
control list, to make any further changes.
2. From Advanced section of the main menu, select Wireless Settings, and then click Setup
Access List to display the Wireless Station Access List screen.
Figure 3-3
3. Click Add to add a wireless device to the wireless access control list. The Wireless Card
Access Setup screen opens and displays a list of currently active wireless cards and their MAC
addresses.
Protecting Your Network
3-3
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Figure 3-4
4. Adjust the list as needed for your network. You can add devices using either of the following
methods:
•
If the computer is in the Available Wireless Cards table, select the radio button of that
computer to capture its MAC address.
•
Use the Add button to enter the MAC address of the device to be added. The MAC
address can usually be found on the bottom of the wireless device.
Note: If no device name appears when you enter the MAC address, you can type a
descriptive name for the computer that you are adding.
5. Click Add, and then click Apply to save these settings. Now, only devices on this list will be
allowed to wirelessly connect to the router.
Blocking Access to Internet Sites
The WNR3500L router allows you to restrict access based on Web addresses and Web address
keywords. Up to 255 entries are supported in the Keyword list.
Keyword application examples:
•
If the keyword XXX is specified, the URL www.zzzyyqq.com/xxx.html is blocked.
Protecting Your Network
3-4
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
•
If the keyword .com is specified, only websites with other domain suffixes (such as .edu, .org,
or .gov) can be viewed.
To block access to Internet sites:
1. Select Block Sites under Content Filtering in the main menu. The Block Sites screen displays.
Figure 3-5
2. Enable keyword blocking by selecting either Per Schedule or Always.
To block by schedule, be sure to specify a time period in the Schedule screen. For information
Block all access to Internet browsing during a scheduled period by entering a dot (.) as the
keyword, and then set a schedule in the Schedule screen.
3. Add a keyword or domain by entering it in the keyword field and clicking Add Keyword. The
keyword or domain name then appears the Block sites containing these keywords or domain
names list.
Delete a keyword or domain name by selecting it from the list and clicking Delete Keyword.
4. You can specify one trusted user, which is a computer that is exempt from blocking and
logging. Specify a trusted user by entering that computer’s IP address in the Trusted IP
Address fields.
Since the trusted user is identified by IP address, you should configure that computer with a
fixed IP address.
Protecting Your Network
3-5
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
5. Click Apply to save all your settings in the Block Sites screen.
Blocking Access to Internet Services
The WNR3500L router allows you to block the use of certain Internet services by computers on
your network. This is called service blocking or port filtering. Services are functions performed by
server computers at the request of client computers. For example, Web servers serve Web pages,
time servers serve time and date information, and game hosts serve data about other players’
moves. When a computer on your network sends a request for service to a server computer on the
Internet, the requested service is identified by a service or port number. This number appears as the
destination port number in the transmitted IP packets. For example, a packet that is sent with
destination port number 80 is an HTTP (Web server) request.
To block access to Internet services:
1. Select Block Services under Content Filtering in the main menu. The Block Services screen
displays.
Figure 3-6
2. Enable service blocking by selecting either Per Schedule or Always, and then click Apply.
To block by schedule, be sure to specify a time period in the Schedule screen. For information
Protecting Your Network
3-6
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
3. Specify a service for blocking by clicking Add. The Block Services Setup screen displays.
Figure 3-7
4. From the Service Type list, select the application or service to be allowed or blocked. The list
already displays several common services, but you are not limited to these choices. To add any
additional services or applications that do not already appear, select User Defined.
5. Select the radio button for the IP address configuration you want to block, and then enter the
IP addresses in the appropriate fields.
You can block the specified service for a single computer, a range of computers (having
consecutive IP addresses), or all computers on your network.
6. Click Add to enable your Block Services Setup selections.
Configuring a User-Defined Service
To define a service, first you must determine which port number or range of numbers is used by
the application. The service port numbers for many common protocols are defined by the Internet
Engineering Task Force (IETF) and published in RFC1700, “Assigned Numbers.” Service
numbers for other applications are typically chosen from the range 1024 to 65535 by the authors of
the application. You can often determine port number information by contacting the publisher of
the application, by asking user groups or newsgroups, or by searching.
•
Enter the starting port and ending port numbers. If the application uses a single port number,
enter that number in both fields.
•
If you know that the application uses either TCP or UDP, select the appropriate protocol. If
you are not sure, select Both.
Protecting Your Network
3-7
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Scheduling Blocking
The WNR3500L router allows you to specify when blocking is enforced.
To schedule blocking:
1. Select Schedule under Content Filtering in the main menu. The Schedule screen displays.
Figure 3-8
2. Configure the schedule for blocking keywords and services.
a. Days to Block. Select days on which you want to apply blocking by selecting the
appropriate check boxes. Select Every Day to select the check boxes for all days. Click
Apply.
b. Time of Day to Block. Select a start and end time in 24-hour format. Select All Day for
24-hour blocking. Click Apply.
Be sure to select your time zone in the E-mail screen as described in “Setting the Time” on
3. Click Apply to save your settings.
Protecting Your Network
3-8
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Viewing Logs of Web Access or Attempted Web Access
The log is a detailed record of the websites you have accessed or attempted to access. Up to
128 entries are stored in the log.
Select Logs under Content Filtering in the main menu. The Logs screen displays.
Figure 3-9
Table 3-1 describes the log entries.
Table 3-1. Log Entry Descriptions
Field
Description
Date and time
Source IP
The date and time the log entry was recorded.
The IP address of the initiating device for this log entry.
Target address
The name or IP address of the website or newsgroup
visited or to which access was attempted.
Action
Whether the access was blocked or allowed.
To refresh the log screen, click the Refresh button.
To clear the log entries, click the Clear Log button.
To e-mail the log immediately, click the Send Log button.
Protecting Your Network
3-9
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Configuring E-mail Alert and Web Access Log Notifications
To receive logs and alerts by e-mail, you must provide your e-mail account information.
To configure e-mail alert and web access log notifications:
1. Select E-mail under Content Filtering in the main menu. The E-mail screen displays.
Figure 3-10
2. To receive e-mail logs and alerts from the router, select the Turn E-mail Notification On
check box.
a. Enter the name of your ISP’s outgoing (SMTP) mail server (such as mail.myISP.com) in
the Your Outgoing Mail Server field. You might be able to find this information in the
configuration screen of your e-mail program. If you leave this field blank, log and alert
messages will not be sent by e-mail.
b. Enter the e-mail address to which logs and alerts are sent in the Send To This E-mail
Address field. This e-mail address will also be used as the From address. If you leave this
field blank, log and alert messages will not be sent by e-mail.
3. If your e-mail server requires authentication, select the My Mail Server requires
authentication check box.
Protecting Your Network
3-10
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
a. Enter your user name for the e-mail server in the User Name field.
b. Enter your password for the e-mail server in the Password field.
4. You can specify that logs are automatically sent by e-mail with these options:
•
Send alert immediately. Select this check box for immediate notification of attempted
access to a blocked site or service.
•
Send Logs According to this Schedule. Specifies how often to send the logs: Hourly,
Daily, Weekly, or When Full.
–
–
Day. Specifies which day of the week to send the log. Relevant when the log is sent
weekly.
Time. Specifies the time of day to send the log. Relevant when the log is sent daily or
weekly.
If you select the Weekly, Daily, or Hourly option and the log fills up before the specified
period, the log is automatically e-mailed to the specified e-mail address. After the log is sent,
the log is cleared from the router’s memory. If the router cannot e-mail the log file, the log
buffer might fill up. In this case, the router overwrites the log and discards its contents.
5. Click Apply to save your settings.
So that the log entries are correctly time-stamped and sent at the correct time, be sure to set the
time as described in the next section.
Setting the Time
The wireless router uses Network Time Protocol (NTP) to obtain the current time and date from
one of several network time servers on the Internet. To localize the time for your log entries, you
must specify your time zone from the E-mail screen:
•
Time Zone. Select your local time zone. This setting is used for the blocking schedule and for
time-stamping log entries.
•
Automatically Adjust for Daylight Savings Time. Select this check box if your region
supports daylight savings time. The router will automatically adjust the time at the start and
end of the daylight savings time period.
Protecting Your Network
3-11
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Using Network Monitoring Tools
This chapter describes how to use the maintenance features of your RangeMax Wireless-N Gigabit
Router with USB WNR3500L. You can access these features by selecting the items under
Maintenance in the main menu of the browser interface.
This chapter includes the following sections:
•
•
•
•
•
Upgrading the Router Firmware
The routing software (also called firmware) of the WNR3500L router is stored in flash memory,
and can be upgraded as NETGEAR releases new software. Your router can download and install
the new software, or you can download upgrade files from the NETGEAR website and manually
send the upgrade file to the router using your browser.
Tip: To ensure that you are always using the latest router firmware, enable the Firmware
Upgrade Assistant feature so that the router will automatically detect a new version
of the firmware on the Internet and alert you to its availability upon login.
4-1
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
The Checking for Firmware Updates screen appears at login unless you clear the Check for
Updated Firmware Upon Log-in check box.
Figure 4-1
A screen is also provided for upgrading the router. From the main menu of the browser interface,
under Maintenance, select Router Upgrade to display the Router Upgrade screen.
Figure 4-2
From this screen, you can check for new software versions by clicking the Check button. If a new
version is found, you can download and install it in one step. To enable the router to automatically
check for a new software version upon login, select the Check for New Version Upon Log-in
check box.
Alternatively, you can manually install an upgrade file stored on your computer.
Tip: Before upgrading the router software, use the router Settings Backup screen to save
your configuration settings. A router upgrade might cause the router settings to
revert to the factory defaults. If this happens, after completing the upgrade, you can
restore your settings from the backup.
Using Network Monitoring Tools
4-2
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Upgrading Automatically to New Router Software
If you have selected Check for New Version Upon Log-in, your router alerts you to the new
software when you log in. Otherwise, you can click the Check button in the Router Upgrade
screen to search for new software.
If the router discovers a newer version of software, the message on the left displays when you log
in. If no new software is available, the message on the right displays.
Figure 4-3
To automatically upgrade to the new software, click Yes to allow the router to download and install
the new software file from NETGEAR.
Warning: When uploading software to the WNR3500L router, do not interrupt the Web
browser by closing the window, clicking a link, or loading a new page. If the
browser is interrupted, it could corrupt the software.
When the upload is complete, your router automatically restarts. The upgrade process typically
takes about 1 minute. Read the new software release notes to determine whether you must
reconfigure the router after upgrading.
Upgrading Manually to New Router Software
To manually select, download, and install new software to your router:
1. Under Maintenance on the main menu, select Router Status. Note the version number of your
router firmware.
2. Go to the WNR3500L support page on the NETGEAR website at
Using Network Monitoring Tools
4-3
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
3. Check the most recent firmware version offered against the firmware version shown on your
Router Status screen.
4. If the version on the NETGEAR website is more recent, download the file to your computer.
5. Under Maintenance on the main menu, select Router Upgrade.
6. Click Browse, and locate the firmware image that you downloaded to your PC (the file ends in
.img or .chk).
7. Click Upload to send the firmware to the router.
Warning: When uploading software to the WNR3500L router, do not interrupt the Web
browser by closing the window, clicking a link, or loading a new page. If the
browser is interrupted, it could corrupt the software.
When the upload is complete, your router automatically restarts. The upgrade process
typically takes about 1 minute. Read the new software release notes to determine whether you
must reconfigure the router after upgrading.
Viewing Wireless Router Status Information
To view router status and usage information:
1. From the main menu of the browser interface, under Maintenance, select Router Status. The
Router Status screen displays.
Using Network Monitoring Tools
4-4
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Figure 4-4
Table 4-1 describes the router status fields.
Table 4-1. Wireless Router Status Fields
Field
Description
Hardware Version
Firmware Version
The router model.
The version of the current software installed in the router. This will
change if you upgrade your router.
Internet Port
These settings apply to the Internet (WAN) port of the router.
MAC Address
The Media Access Control address. This is the unique physical
address being used by the Internet (WAN) port of the router.
IP Address
The IP address being used by the Internet (WAN) port of the router. If
no address is shown, or is 0.0.0.0, the router cannot connect to the
Internet.
Using Network Monitoring Tools
4-5
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Table 4-1. Wireless Router Status Fields (continued)
Field
DHCP
Description
If set to None, the router is configured to use a fixed IP address on
the WAN. If set to DHCP Client, the router is configured to obtain an
IP address dynamically from the ISP.
IP Subnet Mask
The IP subnet mask being used by the Internet (WAN) port of the
router. For an explanation of subnet masks and subnet addressing,
click the link to the online document “TCP/IP Networking Basics” in
Domain Name Server
The Domain Name Server addresses being used by the router. A
Domain Name Server translates human-language URLs such as
www.netgear.com into IP addresses.
LAN Port
These settings apply to the Ethernet (LAN) port of the router.
MAC Address
IP Address
DHCP
The Media Access Control address. This is the unique physical
address being used by the LAN port of the router.
The IP address being used by the Ethernet (LAN) port of the router.
The default is 192.168.1.1.
Identifies whether the router’s built-in DHCP server is active for the
LAN-attached devices.
IP Subnet Mask
The IP subnet mask being used by the Ethernet (LAN) port of the
router. The default is 255.255.255.0.
Wireless Port
These settings apply to the wireless port of the router.
Name (SSID)
The wireless network name (SSID) being used by the wireless port of
the router. The default is NETGEAR.
Region
The geographic region where the router is being used. It might be
illegal to use the wireless features of the router in some parts of the
world.
Channel
Mode
Identifies the channel of the wireless port being used. Click the link to
the frequencies used on each channel. In Up to 300 Mbps mode,
there are two channels: a primary channel (P) and a secondary
channel (S).
Indicates the wireless communication mode:
• Up to 54 Mbps
• Up to 145 Mbps
• Up to 300 Mbps
Wireless AP
Indicates whether the radio feature of the router is enabled. If not
enabled, the Wireless LED on the front panel is off.
Broadcast Name
Indicates whether the router is broadcasting its SSID.
Using Network Monitoring Tools
4-6
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
2. Click Connection Status to display the connection status.
Figure 4-5
Table 4-2 describes the connection status settings.
Table 4-2. Connection Status Settings
Item
Description
IP Address
The IP address that is assigned to the router.
Subnet Mask
Default Gateway
DNS Server
The subnet mask that is assigned to the router.
The IP address for the default gateway that the router communicates with.
The IP address of the Domain Name Service server that provides translation of
network names to IP addresses.
Click the Close Window button to close the Connection Status screen.
Using Network Monitoring Tools
4-7
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
3. Click Show Statistics to display router usage statistics.
Figure 4-6
Table 4-3 describes the router statistics.
Table 4-3. Router Statistics
Item
Description
System Up Time
Port
The time elapsed since the router was last restarted.
The statistics for the WAN (Internet) and LAN (Ethernet) ports. For each port, the
screen displays the following:
Status
The link status of the port.
TxPkts
RxPkts
Collisions
Tx B/s
The number of packets transmitted on this port since reset.
The number of packets received on this port since reset.
The number of collisions on this port since reset.
The current transmission (outbound) bandwidth used on the WAN and LAN ports
(the average bytes per second transmitted since reset). Tx B/s is the total bytes
transmitted divided by the system up time (in seconds).
Rx B/s
The current reception (inbound) bandwidth used on the WAN and LAN ports (the
average bytes per second received since reset). Rx B/s is the total bytes received
divided by the system up time (in seconds).
Up Time
The time elapsed since this port acquired the link.
Poll Interval
The intervals at which the statistics are updated in this screen.
To change the polling frequency, enter a time in seconds in the Poll Interval field, and click
Set Interval.
To stop the polling entirely, click Stop.
Using Network Monitoring Tools
4-8
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Viewing a List of Attached Devices
The Attached Devices screen contains a table of all IP devices that the router has discovered on the
local network. From the main menu of the browser interface, under Maintenance, select Attached
Devices to view the table.
Figure 4-7
For each device, the table shows the IP address, NetBIOS host name or device name (if available),
and the Ethernet MAC address. To force the router to look for attached devices, click Refresh.
Note: If the router is rebooted, the table data is lost until the router rediscovers the
devices.
Managing the Configuration File
The configuration settings of the WNR3500L router are stored within the router in a configuration
file. You can back up (save) this file to your computer, restore it, or reset it to the factory default
settings.
Using Network Monitoring Tools
4-9
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
From the main menu of the browser interface, under Maintenance, select Backup Settings.
Figure 4-8
The following sections describe the three available options.
Backing Up and Restoring the Configuration
The Restore and Backup options in the Settings Backup screen let you save and retrieve a file
containing your router’s configuration settings.
To save your settings, click Back Up. Your browser extracts the configuration file from the router
and prompts you for a location on your computer to store the file. You can give the file a
meaningful name at this time, such as comcast.cfg.
Tip: Before saving your configuration file, change the administrator password to the
default, password. Then change it again after you have saved the configuration file.
If you forget the password, you will need to reset the configuration to factory
defaults.
To restore your settings from a saved configuration file, enter the full path to the file on your
computer, or click Browse to browse to the file. When you have located it, click Restore to send
the file to the router. The router then reboots automatically.
Warning: Do not interrupt the reboot process.
Using Network Monitoring Tools
4-10
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Erasing the Configuration
Under some circumstances (for example, if you move the router to a different network or if you
have forgotten the password) you might want to erase the configuration and restore the factory
default settings. After an erase, the router’s username is admin, the password is password, the
LAN IP address is 192.168.1.1 (or www.routerlogin.net), and the router’s DHCP server is
enabled.
To erase the configuration, click the Erase button in the Settings Backup screen.
To restore the factory default configuration settings when you do not know the login password or
IP address, you must use the restore factory settings button on the rear panel of the router (see
Enabling Remote Management Access
Using the Remote Management feature, you can allow a user on the Internet to configure, upgrade,
and check the status of your WNR3500L router. From the main menu of the browser interface,
under Advanced, select Remote Management.
Figure 4-9
Using Network Monitoring Tools
4-11
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Note: Be sure to change the router’s default configuration password to a very secure
password. The ideal password should contain no dictionary words from any
language, and should be a mixture of letters (both uppercase and lowercase),
numbers, and symbols. Your password can be up to 30 characters.
To configure your router for remote management:
1. Select the Turn Remote Management On check box.
2. Under Allow Remote Access By, specify what external IP addresses will be allowed to access
the router’s remote management.
Note: For enhanced security, restrict access to as few external IP addresses
as practical.
•
•
To allow access from any IP address on the Internet, select Everyone.
To allow access from a range of IP addresses on the Internet, select IP Address Range.
Enter a beginning and ending IP address to define the allowed range.
•
To allow access from a single IP address on the Internet, select Only This Computer.
Enter the IP address that will be allowed access.
3. Specify the port number for accessing the management interface.
Normal Web browser access uses the standard HTTP service port 80. For greater security,
enter a custom port number for the remote management Web interface. Choose a number
between 1024 and 65535, but do not use the number of any common service port. The default
is 8080, which is a common alternate for HTTP.
4. Click Apply to have your changes take effect.
Note: When accessing your router from the Internet, type your router’s WAN IP address
into your browser’s address or location field, followed by a colon (:) and the
custom port number. For example, if your external address is 134.177.0.123 and
you use port number 8080, then enter http://134.177.0.123:8080 in your browser.
Using Network Monitoring Tools
4-12
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5
Customizing Your Network Settings
This chapter describes advanced features of the RangeMax Wireless-N Gigabit Router with USB
WNR3500L. This chapter includes the following sections:
•
•
•
•
•
•
•
•
Using the LAN IP Setup Options
The LAN Setup screen allows configuration of LAN IP services such as Dynamic Host
Configuration Protocol (DHCP) and Routing Information Protocol (RIP).
The router is shipped preconfigured to use private IP addresses on the LAN side and to act as a
DHCP server. The router’s default LAN IP configuration is:
•
•
LAN IP address: 192.168.1.1
Subnet mask: 255.255.255.0
These addresses are part of the designated private address range for use in private networks and
should be suitable for most applications. If your network has a requirement to use a different IP
addressing scheme, you can make those changes in the LAN Setup screen.
5-1
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
To configure LAN IP settings, log in to the router, and under the Advanced heading, select LAN
Setup. The following screen displays:
.
Figure 5-1
If you make changes, you must click Apply in order for the changes to take effect.
Note: If you change the LAN IP address of the router while connected through the
browser, you will be disconnected. You must then open a new connection to the
new IP address and log in again.
The LAN Setup fields are explained in the following table.
Table 5-1. LAN IP Setup
Settings
Description
Device Name
A descriptive name for the router, which will be shown in the
Network on Windows Vista and the Network Explorer on all
Windows systems. The Device Name field cannot be blank.
Customizing Your Network Settings
5-2
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Table 5-1. LAN IP Setup (continued)
Settings
Description
LAN TCP/IP
Setup
IP Address
The LAN IP address of the wireless router.
IP Subnet Mask
The LAN subnet mask of the wireless router. Combined
with the IP address, the IP Subnet Mask allows a device to
know which other addresses are local to it, and which must
be reached through a gateway or wireless router.
RIP Direction
RIP (Router Information Protocol) allows a wireless router
to exchange routing information with other routers. This
setting controls how the wireless router sends and receives
RIP packets. Both is the default.
• Both or Out Only. The wireless router broadcasts its
routing table periodically.
• Both or In Only. The wireless router incorporates the RIP
information that it receives.
• None. The wireless router will not send any RIP packets
and will ignore any RIP packets received.
RIP Version
This controls the format and the broadcasting method of the
RIP packets that the wireless router sends. It recognizes
both formats when receiving. By default, this is RIP-1.
• RIP-1 is universally supported. It is adequate for most
networks, unless you have an unusual network setup.
• RIP-2 carries more information. Both RIP-2B and RIP-2M
send the routing data in RIP-2 format. RIP-2B uses
subnet broadcasting. RIP-2M uses multicasting.
DHCP Server
For more
information
Use Router as a DHCP
Server
This check box is usually selected so that the wireless
router functions as a Dynamic Host Configuration Protocol
(DHCP) server. See “Using the Router as a DHCP Server”
Starting IP Address
Ending IP Address
Specify the start of the range for the pool of IP addresses in
the same subnet as the wireless router.
Specify the end of the range for the pool of IP addresses in
the same subnet as the wireless router.
Address Reservation
For more information, see “Using Address
When you specify a reserved IP address for a computer on
the LAN, that computer receives the same IP address each
time it access the router’s DHCP server. Assign reserved IP
addresses to servers that require permanent IP settings.
Customizing Your Network Settings
5-3
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Using the Router as a DHCP Server
By default, the router functions as a DHCP server, allowing it to assign IP, DNS server, and default
gateway addresses to all computers connected to the router’s LAN. The assigned default gateway
address is the LAN address of the router. The router assigns IP addresses to the attached computers
from a pool of addresses specified in this screen. Each pool address is tested before it is assigned to
avoid duplicate addresses on the LAN.
For most applications, the default DHCP and TCP/IP settings of the router are satisfactory. Click
DHCP and information about how to assign IP addresses for your network.
Specify the pool of IP addresses to be assigned by setting the starting IP address and ending IP
address. These addresses should be part of the same IP address subnet as the router’s LAN IP
address. Using the default addressing scheme, you should define a range between 192.168.1.2 and
192.168.1.254, although you might wish to save part of the range for devices with fixed addresses.
The router delivers the following parameters to any LAN device that requests DHCP:
•
•
•
•
An IP address from the range you have defined
Subnet mask
Gateway IP address (the router’s LAN IP address)
Primary DNS server
To use another device on your network as the DHCP server, or to manually specify the network
settings of all of your computers, clear the Use Router as DHCP Server check box. Otherwise,
leave it selected. If this service is not selected and no other DHCP server is available on your
network, you need to set your computers’ IP addresses manually or they will not be able to access
the router.
Using Address Reservation
When you specify a reserved IP address for a computer on the LAN, that computer always
receives the same IP address each time it accesses the router’s DHCP server. Reserved IP
addresses should be assigned to computers or servers that require permanent IP settings.
To reserve an IP address:
1. Click Add.
2. In the IP Address field, type the IP address to assign to the computer or server. (Choose an IP
address from the router’s LAN subnet, such as 192.168.1.x.)
Customizing Your Network Settings
5-4
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
3. Type the MAC address of the computer or server.
Tip: If the computer is already present on your network, you can copy its MAC
address from the Attached Devices screen and paste it here.
4. Click Apply to enter the reserved address into the table.
Note: The reserved address is not assigned until the next time the computer contacts
the router’s DHCP server. Reboot the computer or access its IP configuration
and force a DHCP release and renew.
To edit or delete a reserved address entry:
1. Click the button next to the reserved address you want to edit or delete.
2. Click Edit or Delete.
Using a Dynamic DNS Service
If your Internet Service Provider (ISP) gave you a permanently assigned IP address, you can
register a domain name and have that name linked with your IP address by public Domain Name
Servers (DNS). However, if your Internet account uses a dynamically assigned IP address, you do
not know in advance what your IP address will be, and the address can change frequently. In this
case, you can use a commercial Dynamic DNS service, which allows you to register your domain
to their IP address, and forwards traffic directed at your domain to your current IP address.
Note: If your ISP assigns a private WAN IP address (such as 192.168.x.x or 10.x.x.x), the
Dynamic DNS service will not work because private addresses are not routed on
the Internet.
Your router contains a client that can connect to the Dynamic DNS service provided by
name, which you specify in the router. Then, whenever your ISP-assigned IP address changes,
your router automatically contacts the Dynamic DNS service provider, logs in to your account, and
registers your new IP address. If your host name is hostname, for example, you can reach your
router at hostname.dyndns.org.
Customizing Your Network Settings
5-5
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
From the main menu of the browser interface, under Advanced, select Dynamic DNS to display
the Dynamic DNS screen.
Figure 5-2
To configure Dynamic DNS:
1. Register for an account with one of the Dynamic DNS service providers whose names appear
in the Service Provider list. For example, for DynDNS.org, select www.dyndns.org.
2. Select the Use a Dynamic DNS Service check box.
3. Select the name of your Dynamic DNS service provider.
4. Type the host name (or domain name) that your Dynamic DNS service provider gave you.
5. Type the user name for your Dynamic DNS account. This is the name that you use to log in to
your account, not your host name.
6. Type the password (or key) for your Dynamic DNS account.
7. Click Apply to save your configuration.
Customizing Your Network Settings
5-6
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Configuring the WAN Setup Options
The WAN Setup screen lets you configure a DMZ (demilitarized zone) server, change the
Maximum Transmit Unit (MTU) size, and enable the wireless router to respond to a ping on the
WAN (Internet) port. From the main menu, under Advanced, click WAN Setup to view the WAN
Setup screen.
Figure 5-3
The WAN Setup fields are described in the following table:
Table 5-2. WAN Setup Settings
Setting
Description
Disable SPI Firewall
The Stateful Packet Inspection (SPI) firewall protects your network and
computers against attacks and intrusions. A stateful packet firewall carefully
inspects incoming traffic packets, looking for known exploits such as
malformed, oversized, or out-of-sequence packets. The firewall should be
disabled only in special circumstances, such as when you are troubleshooting
application issues.
Default DMZ Server
This feature is sometimes helpful when you are using some online games and
videoconferencing. Be careful when using this feature because it makes the
firewall security less effective. See the following section, Setting Up a Default
Respond to Ping on Internet If you want the wireless router to respond to a ping from the Internet, select
WAN Port
this check box. This should be used only as a diagnostic tool, since it allows
your wireless router to be discovered. Do not select this check box unless you
have a specific reason to do so.
Customizing Your Network Settings
5-7
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Table 5-2. WAN Setup Settings
Setting
Description
MTU Size (in bytes)
The normal MTU (Maximum Transmit Unit) value for most Ethernet networks
is 1500 bytes, or 1492 Bytes for PPPoE connections. For some ISPs you
might need to reduce the MTU. This is rarely required, and should not be done
unless you are sure it is necessary for your ISP connection. See “Changing
NAT Filtering
Network Address Translation (NAT) determines how the router processes
inbound traffic. Secured NAT provides a secured firewall to protect the
computers on the LAN from attacks from the Internet, but might prevent some
Internet games, point-to-point applications, or multimedia applications from
functioning. Open NAT provides a much less secured firewall, but allows
almost all Internet applications to function.
Setting Up a Default DMZ Server
The default DMZ server feature is helpful when you are using some online games and
videoconferencing applications that are incompatible with Network Address Translation (NAT).
The router is programmed to recognize some of these applications and to work correctly with
them, but there are other applications that might not function well. In some cases, one local
computer can run the application correctly if that computer’s IP address is entered as the default
DMZ server.
Warning: DMZ servers pose a security risk. A computer designated as the default DMZ
server loses much of the protection of the firewall, and is exposed to exploits
from the Internet. If compromised, the DMZ server computer can be used to
attack other computers on your network.
Incoming traffic from the Internet is usually discarded by the router unless the traffic is a response
to one of your local computers or a service that you have configured in the Port Forwarding/Port
Triggering screen. Instead of discarding this traffic, you can have it forwarded to one computer on
your network. This computer is called the default DMZ server.
The WAN Setup screen lets you configure a default DMZ server.
To assign a computer or server to be a default DMZ server:
1. In the last Default DMZ Server field, type the last digit of the IP address for that computer.
To remove the default DMZ server, enter 0 (zero).
2. Select the Default DMZ Server check box, and click Apply.
Customizing Your Network Settings
5-8
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Configuring Static Routes
Static routes provide additional routing information to your router. Under usual circumstances, the
router has adequate routing information after it has been configured for Internet access, and you do
not need to configure additional static routes. You must configure static routes only for unusual
cases such as multiple routers or multiple IP subnets located on your network.
As an example of when a static route is needed, consider the following case:
•
•
Your primary Internet access is through a cable modem to an ISP.
You have an ISDN router on your home network for connecting to the company where you are
employed. This router’s address on your LAN is 192.168.1.100.
•
Your company’s network address is 134.177.0.0.
When you first configured your router, two implicit static routes were created. A default route was
created with your ISP as the gateway, and a second static route was created to your local network
for all 192.168.1.x addresses. With this configuration, if you attempt to access a device on the
134.177.0.0 network, your router forwards your request to the ISP. The ISP forwards your request
to the company where you are employed, and the request is likely to be denied by the company’s
firewall.
In this case you must define a static route, telling your router that 134.177.0.0 should be accessed
through the ISDN router at 192.168.1.100.
In this example:
•
The Destination IP Address and IP Subnet Mask fields specify that this static route applies
to all 134.177.x.x addresses.
•
The Gateway IP Address field specifies that all traffic for these addresses should be
forwarded to the ISDN router at 192.168.1.100.
•
•
A Metric value of 1 will work.
Private is selected only as a precautionary security measure in case RIP is activated.
Customizing Your Network Settings
5-9
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Select Static Routes under Advanced in the main menu. The Static Routes screen displays.
Figure 5-4
To add or edit a static route:
1. Click Add to expand the Static Routes screen.
Figure 5-5
2. In the Route Name field, type a name for this static route. (This is for identification purposes
only.)
3. Select the Private check box if you want to limit access to the LAN only. If Private is selected,
the static route is not reported in RIP.
4. Select the Active check box to make this route effective.
5. Type the IP address of the final destination.
6. Type the IP subnet mask for this destination.
If the destination is a single host, type 255.255.255.255.
Customizing Your Network Settings
5-10
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
7. Type the gateway IP address, which must be a router on the same LAN segment as the
WNR3500L router.
8. Type a number between 1 and 15 as the metric value.
This represents the number of routers between your network and the destination.
Usually, a setting of 2 or 3 works.
9. Click Apply to have the static route entered into the table.
Allowing Inbound Connections to Your Network
By default, the WNR3500L router blocks any inbound traffic from the Internet to your computers
except for replies to your outbound traffic. However, you might need to create exceptions to this
rule for the following purposes:
•
•
To allow remote computers on the Internet to access a server on your local network.
To allow certain applications and games to work correctly when their replies are not
recognized by your router.
Your router provides two features for creating these exceptions: port forwarding and port
triggering. This section explains how a normal outbound connection works, followed by two
examples explaining how port forwarding and port triggering operate and how they differ.
How Your Computer Accesses a Remote Computer through Your
Router
When a computer on your network needs to access a computer on the Internet, your computer
sends your router a message containing source and destination address and process information.
Before forwarding your message to the remote computer, your router must modify the source
information and must create and track the communication session so that replies can be routed
back to your computer.
Here is an example of normal outbound traffic and the resulting inbound responses:
1. You open Internet Explorer, beginning a browser session on your computer. Invisible to you,
your operating system assigns a service number (port number) to every communication
process running on your computer. In this example, let’s say Windows assigns port number
5678 to this browser session.
2. You ask your browser to get a Web page from the Web server at www.example.com. Your
computer composes a Web page request message with the following address and
port information:
Customizing Your Network Settings
5-11
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
•
•
•
The source address is your computer’s IP address.
The source port number is 5678, the browser session.
The destination address is the IP address of www.example.com, which your computer
finds by asking a DNS server.
•
The destination port number is 80, the standard port number for a Web server process.
Your computer then sends this request message to your router.
3. Your router creates an entry in its internal session table describing this communication session
between your computer and the Web server at www.example.com. Before sending the Web
page request message to www.example.com, your router stores the original information and
then modifies the source information in the request message, performing Network Address
Translation (NAT):
•
The source address is replaced with your router’s public IP address.
This is necessary because your computer uses a private IP address that is not globally
unique and cannot be used on the Internet.
•
The source port number is changed to a number chosen by the router, such as 33333. This
is necessary because two computers could independently be using the same session
number.
Your router then sends this request message through the Internet to the Web server at
www.example.com.
4. The Web server at www.example.com composes a return message with the requested Web
page data. The return message contains the following address and port information:
•
•
•
•
The source address is the IP address of www.example.com.
The source port number is 80, the standard port number for a Web server process.
The destination address is the public IP address of your router.
The destination port number is 33333.
The Web server then sends this reply message to your router.
5. Upon receiving the incoming message, your router checks its session table to determine
whether there is an active session for port number 33333. Finding an active session, the router
then modifies the message, restoring the original address information replaced by NAT. The
message now contains the following address and port information:
•
•
The source address is the IP address of www.example.com.
The source port number is 80, the standard port number for a Web server process.
Customizing Your Network Settings
5-12
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
•
•
The destination address is your computer’s IP address.
The destination port number is 5678, the browser session that made the initial request.
Your router then sends this reply message to your computer, which displays the Web page
from www.example.com.
6. When you finish your browser session, your router senses the termination of communications.
Your router then removes the session information from its session table, and incoming traffic
is no longer accepted on port number 33333.
How Port Triggering Changes the Communication Process
In the preceding example, requests are sent to a remote computer by your router from a particular
service port number, and replies from the remote computer to your router are directed to that port
number. If the remote server sends a reply back to a different port number, your router will not
recognize it and will discard it. However, some application servers (such as FTP and IRC servers)
send replies back to multiple port numbers. Using the port triggering function of your router, you
can tell the router to open additional incoming ports when a particular outgoing port originates
a session.
An example is Internet Relay Chat (IRC). Your computer connects to an IRC server at destination
port 6667. The IRC server not only responds to your originating source port, but also sends an
“identify” message to your computer on port 113. Using port triggering, you can tell the router,
“When you initiate a session with destination port 6667, you must also allow incoming traffic on
port 113 to reach the originating computer.” Using steps similar to the preceding example, the
following sequence shows the effects of the port triggering rule you have defined:
1. You open an IRC client program, beginning a chat session on your computer.
2. Your IRC client composes a request message to an IRC server using a destination port number
of 6667, the standard port number for an IRC server process. Your computer then sends this
request message to your router.
3. Your router creates an entry in its internal session table describing this communication session
between your computer and the IRC server. Your router stores the original information,
performs Network Address Translation (NAT) on the source address and port, and sends this
request message through the Internet to the IRC server.
4. Noting your port triggering rule, and having observed the destination port number of 6667,
your router creates an additional session entry to send any incoming port 113 traffic to your
computer.
Customizing Your Network Settings
5-13
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
5. The IRC server sends a return message to your router using the NAT-assigned source port (as
in the previous example, let’s say port 33333) as the destination port. The IRC server also
sends an “identify” message to your router with destination port 113.
6. Upon receiving the incoming message to destination port 33333, your router checks its session
table to determine whether there is an active session for port number 33333. Finding an active
session, the router restores the original address information replaced by NAT and sends this
reply message to your computer.
7. Upon receiving the incoming message to destination port 113, your router checks its session
table and learns that there is an active session for port 113, associated with your computer. The
router replaces the message’s destination IP address with your computer’s IP address and
forwards the message to your computer.
8. When you finish your chat session, your router senses the termination of communications. The
router then removes the session information from its session table, and incoming traffic is no
longer accepted on port numbers 33333 or 113.
To configure port triggering, you need to know which inbound ports the application needs. Also,
you need to know the number of the outbound port that will trigger the opening of the inbound
ports. You can usually determine this information by contacting the publisher of the application, or
user groups or newsgroups.
Note: An inbound port can be used by one computer at a time with the triggered
application.
How Port Forwarding Changes the Communication Process
In both of the preceding examples, your computer initiates an application session with a server
computer on the Internet. However, you might need to allow a client computer on the Internet to
initiate a connection to a server computer on your network. Normally, your router ignores any
inbound traffic that is not a response to your own outbound traffic. You can configure exceptions
to this default rule by using the port forwarding feature.
A typical application of port forwarding can be shown by reversing the client-server relationship
from our previous Web server example. In this case, a remote computer’s browser needs to access
a Web server running on a computer in your local network. Using port forwarding, you can tell the
router, “When you receive incoming traffic on port 80 (the standard port number for a Web server
process), forward it to the local computer at 192.168.1.123.” The following sequence shows the
effects of the port forwarding rule you have defined:
Customizing Your Network Settings
5-14
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
1. The user of a remote computer opens Internet Explorer and requests a Web page from
www.example.com, which resolves to the public IP address of your router. The remote
computer composes a Web page request message with the following destination information:
•
The destination address is the IP address of www.example.com, which is the address of
your router.
•
The destination port number is 80, the standard port number for a Web server process.
The remote computer then sends this request message through the Internet to your router.
2. Your router receives the request message and looks in its rules table for any rules covering the
disposition of incoming port 80 traffic. Your port forwarding rule specifies that incoming port
80 traffic should be forwarded to local IP address 192.168.1.123. Therefore, your router
modifies the destination information in the request message:
The destination address is replaced with 192.168.1.123.
Your router then sends this request message to your local network.
3. Your Web server at 192.168.1.123 receives the request and composes a return message with
the requested Web page data. Your Web server then sends this reply message to your router.
4. Your router performs Network Address Translation (NAT) on the source IP address, and sends
this request message through the Internet to the remote computer, which displays the Web
page from www.example.com.
To configure port forwarding, you need to know which inbound ports the application needs. You
usually can determine this information by contacting the publisher of the application or user
groups or newsgroups.
How Port Forwarding Differs from Port Triggering
The following points summarize the differences between port forwarding and port triggering:
•
Port triggering can be used by any computer on your network, although only one computer at a
time can use the same ports.
•
•
Port forwarding is configured for a single computer on your network.
Port triggering does not need to know the computer’s IP address in advance. The IP address is
captured automatically.
•
•
•
Port forwarding requires that you specify the computer’s IP address during configuration, and
the IP address must never change.
Port triggering requires specific outbound traffic to open the inbound ports, and the triggered
ports are closed after a period of no activity.
Port forwarding is always active and does not need to be triggered.
Customizing Your Network Settings
5-15
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Configuring Port Forwarding to Local Servers
Using the port forwarding feature, you can allow certain types of incoming traffic to reach servers
on your local network. For example, you might make a local Web server, FTP server, or game
server visible and available to the Internet.
Use the Port Forwarding screen to configure the router to forward specific incoming protocols to
computers on your local network. In addition to servers for specific applications, you can also
specify a default DMZ server to which all other incoming protocols are forwarded. The DMZ
Before starting, you need to determine which type of service, application, or game you will
provide, and the local IP address of the computer that will provide the service. Be sure the
computer’s IP address never changes.
Tip: To ensure that your server computer always has the same IP address, use the
reserved IP address feature of your WNR3500L router. See “Using Address
Reservation” on page 5-4 for instructions on how to use reserved IP addresses.
To configure port forwarding to a local server:
1. Select Port Forwarding/Port Triggering under Advanced in the main menu.
Figure 5-6
Customizing Your Network Settings
5-16
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
2. From the Service Name list, select the service or game that you will host on your network.
If the service does not appear in the list, see the following section, “Adding a Custom
Service.”
3. In the corresponding Server IP Address box, enter the last digit of the IP address of your local
computer that will provide this service.
4. Click Add. The service appears in the list in the screen.
Adding a Custom Service
To define a service, game, or application that does not appear in the Service Name list, you must
first determine which port number or range of numbers is used by the application. You can usually
determine this information by contacting the publisher of the application or user groups or
newsgroups. When you have the port number information, follow these steps:
1. Select Port Forwarding/Port Triggering under Advanced in the main menu.
2. Click Add Custom Service.
Figure 5-7
3. In the Service Name field, enter a descriptive name.
4. In the Service Type field, select the protocol. If you are unsure, select TCP/UDP.
5. In the Starting Port field, enter the beginning port number.
•
If the application uses only a single port, enter the same port number in the Ending Port
field.
•
If the application uses a range of ports, enter the ending port number of the range in the
Ending Port field.
6. In the Server IP Address field, enter the IP address of your local computer that will provide
this service.
7. Click Apply. The service appears in the list in the Port Forwarding/Port Triggering screen.
Customizing Your Network Settings
5-17
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Editing or Deleting a Port Forwarding Entry
To edit or delete a port forwarding entry:
1. In the table, select the button next to the service name.
2. Click Edit Service or Delete Service.
Application Example: Making a Local Web Server Public
If you host a Web server on your local network, you can use port forwarding to allow Web requests
from anyone on the Internet to reach your Web server.
To make a local Web server public:
1. Assign your Web server either a fixed IP address or a dynamic IP address using DHCP address
router will always give your Web server an IP address of 192.168.1.33.
2. In the Port Forwarding screen, configure the router to forward the HTTP service to the local
address of your Web server at 192.168.1.33.
HTTP (port 80) is the standard protocol for Web servers.
3. (Optional) Register a host name with a Dynamic DNS service, and configure your router to
To access your Web server from the Internet, a remote user must know the IP address that has
been assigned by your ISP. However, if you use a Dynamic DNS service, the remote user can
reach your server by a user-friendly Internet name, such as mynetgear.dyndns.org.
Configuring Port Triggering
Port triggering is a dynamic extension of port forwarding that is useful in these cases:
•
More than one local computer needs port forwarding for the same application (but not
simultaneously).
•
An application needs to open incoming ports that are different from the outgoing port.
When port triggering is enabled, the router monitors outbound traffic looking for a specified
outbound “trigger” port. When the router detects outbound traffic on that port, it remembers the IP
address of the local computer that sent the data. The router then temporarily opens the specified
incoming port or ports, and forwards incoming traffic on the triggered ports to the triggering
computer.
Customizing Your Network Settings
5-18
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
While port forwarding creates a static mapping of a port number or range to a single local
computer, port triggering can dynamically open ports to any computer that needs them and can
close the ports when they are no longer needed.
Note: If you use applications such as multiplayer gaming, peer-to-peer connections, real-
time communications such as instant messaging, or remote assistance (a feature in
Windows XP), you should also enable Universal Plug and Play (UPnP) according
To configure port triggering, you need to know which inbound ports the application needs. Also,
you need to know the number of the outbound port that will trigger the opening of the inbound
ports. You can usually determine this information by contacting the publisher of the application or
user groups or newsgroups.
To set up port triggering:
1. Select Port Forwarding/Port Triggering under Advanced in the main menu. The
Forwarding/Port Triggering screen displays.
2. Select the Port Triggering radio button. The port triggering information displays.
Figure 5-8
Customizing Your Network Settings
5-19
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
3. Clear the Disable Port Triggering check box.
Note: If the Disable Port Triggering check box is selected after you configure port
triggering, port triggering is disabled. However, any port triggering
configuration information you added to the router is retained even though it is
not used.
4. In the Port Triggering Timeout field, enter a value up to 9999 minutes. This value sets the
inactivity timer for the designated inbound ports. These ports close when the timer expires.
This is required because the router cannot be sure when the application has terminated.
5. Click Add Service.
Figure 5-9
6. In the Service Name field, type a descriptive service name.
7. In the Service User field, select Any (the default) to allow this service to be used by any
computer on the Internet. Otherwise, select Single address, and enter the IP address of one
computer to restrict the service to a particular computer.
8. Select the service type, either TCP or UDP or both (TCP/UDP). If you are not sure, select
TCP/UDP.
9. In the Triggering Port field, enter the number of the outbound traffic port that will cause the
inbound ports to be opened.
10. Enter the inbound connection port information in the Connection Type, Starting Port, and
Ending Port fields.
11. Click Apply. The service appears in the Port Triggering Portmap table.
Customizing Your Network Settings
5-20
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Wireless Repeating (Also Called WDS)
The WNR3500L router can be used with a wireless access point (AP) to build large bridged
wireless networks. Wireless repeating is a type of Wireless Distribution System (WDS).
Warning: If you use the wireless repeating function, your options for wireless security
are limited to None or WEP. For more information about wireless security, see
Chapter 2, “Safeguarding Your Network.”
The following figure shows a wireless repeating scenario:
Repeater AP
Base Station AP
Figure 5-10
To set up a wireless network using WDS, the following conditions must be met for both APs:
•
Both APs must use the same wireless channel and encryption mode (see “Manually
Configuring Your Wireless Settings” on page 2-4 or “Using Push 'N' Connect (WPS) to
Configure Your Wireless Network” on page 2-13).
•
•
Both APs must be on the same LAN IP subnet. That is, all the AP LAN IP addresses are in the
same network.
All LAN devices (wired and wireless computers) must be configured to operate in the same
LAN network address range as the APs.
Customizing Your Network Settings
5-21
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Wireless Repeating Function
You can view or change wireless repeater settings for the wireless router. From the main menu of
the browser interface, under Advanced, click Wireless Repeating Function to display the
Wireless Repeating Function screen.
Figure 5-11
The wireless router supports two modes of the wireless repeating function, and allows you to
control wireless client association:
•
•
•
Wireless Repeater. The wireless router sends all traffic from its local wireless or wired
computers to a remote AP. To configure this mode, you must know the MAC address of the
remote parent AP.
Wireless Base Station. The wireless router acts as the parent AP, bridging traffic to and from
the child repeater AP, as well as handling wireless and wired local computers. To configure
this mode, you must know the MAC addresses of the child repeater AP.
Disable Wireless Client Association. Usually this check box is cleared so that the router is an
access point for wireless computers.
If this check box is selected, the router communicates wirelessly only with other APs whose MAC
addresses are listed in this screen. The router still communicates with wire-connected LAN
devices.
Customizing Your Network Settings
5-22
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Setting Up the Base Station
The wireless repeating function works only in hub and spoke mode. The units cannot be daisy
chained. You must know the wireless settings for both units. You must know the MAC address of
the remote unit. First, set up the base station, and then set up the repeater. To set up the base
station:
1. Set up both units with exactly the same wireless settings (mode, channel, and security). Note
that the wireless security option must be set to None or WEP.
2. Log into the wireless router base unit, under the Advanced heading, select Wireless
Repeating Function to display the Wireless Repeating Function screen.
Figure 5-12
3. Select the Enable Wireless Repeating Function check box and the Wireless Base Station
radio button.
4. Enter the MAC address for one or more repeater units.
5. Click Apply to save your changes.
Customizing Your Network Settings
5-23
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Setting Up a Repeater Unit
Use a wired Ethernet connection to set up the repeater unit to avoid conflicts with the wireless
connection to the base station.
Note: If you are using the WNR3500L base station with a non-NETGEAR wireless
router as the repeater, you might need to change additional configuration settings.
In particular, you should disable the DHCP server function on the wireless
repeater AP.
To configure a WNR3500L router as a repeater unit:
1. If you are using the same model of wireless router for both the base station and repeaters, you
must change the LAN IP address for each repeater to a different IP address in the same subnet
Note: Failing to change the LAN IP address will cause an IP address conflict in the
network because the factory default LAN IP is the same for both units.
2. Log in to the router that will be the repeater. Check the Wireless Settings screen, and verify
that the wireless settings match the base unit exactly. If the settings are different, be sure to
configure the wireless settings to match the base station settings.
3. In the Wireless Repeating Function screen, select the Enable Wireless Repeating Function
check box and the Wireless Repeater radio button.
4. Fill in the IP Address field. This IP address must be in the same subnet as the base station, but
different from the LAN IP of the base station.
5. Fill in the Base Station MAC Address field.
6. Click Apply to save your changes.
7. Verify connectivity across the LANs.
A computer on any wireless or wired LAN segment of the wireless router should be able to
connect to the Internet or share files and printers with any other wireless or wired computer or
server connected to the other AP.
Customizing Your Network Settings
5-24
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6
Fine-Tuning Your Network
This chapter describes how to modify the configuration of the RangeMax Wireless-N Gigabit
Router with USB WNR3500L to allow specific applications to access the Internet or to be
accessed from the Internet, and how to make adjustments to enhance your network’s performance.
This chapter includes the following sections:
•
•
•
•
•
•
Common connection types and their speed and security considerations are:
•
Broadband Internet. Your Internet connection speed is determined by your modem type,
such as ADSL or cable modem, as well as the connection speed of the sites to which you
connect, and general Internet traffic. ADSL and cable modem connections are asymmetrical,
meaning they have a lower data rate to the Internet (upstream) than from the Internet
(downstream). Keep in mind that when you connect to another site that also has an
asymmetrical connection, the data rate between your sites is limited by each side’s upstream
and downstream data rate. A typical residential ADSL or cable modem connection provides a
downstream throughput of about 1 to 3 megabits per second (Mbps). Newer technologies such
as ADSL2+ and Fiber to the Home (FTTH) will increase the connection speed to tens of
Mbps.
•
Wireless. Your RangeMax Wireless-N Gigabit Router with USB WNR3500L provides a
wireless link rate of up to 300 Mbps using technology called multiple input, multiple output
(MIMO), in which multiple antennas transmit multiple streams of data. The use of multiple
antennas also provides excellent range and coverage. With the introduction of the newer WPA
and WPA2 encryption and authentication protocols, wireless security is extremely strong.
6-1
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
To get the best performance, use RangeMax NEXT adapters such as the WN511B for your
computers. Although the RangeMax NEXT router is compatible with older 802.11b and
802.11g adapters, the use of these older wireless technologies in your network can result in
lower throughput overall (typically less than 10 Mbps for 802.11b and less than 40 Mbps for
802.11g). In addition, many older wireless products do not support the latest security
protocols, WPA and WPA2.
•
Powerline. For connecting rooms or floors that are blocked by obstructions or are distant
vertically, consider networking over your building’s AC wiring. NETGEAR’s Powerline HD
family of products delivers up to 200 Mbps to any outlet, while the older-generation XE
family of products delivers 14 Mbps or 85 Mbps. Data transmissions are encrypted for
security, and you can configure an individual network password to prevent neighbors from
connecting.
The Powerline HD family of products can coexist on the same network with older-generation
XE family products or HomePlug 1.0 products, but they are not interoperable with these older
products.
•
Wired Ethernet. As gigabit-speed Ethernet ports (10/100/1000 Mbps) become common on
newer computers, wired Ethernet remains a good choice for speed, economy, and security.
Gigabit Ethernet can extend up to 100 meters with twisted-pair wiring of Cat 5e or better. A
wired connection is not susceptible to interference, and eavesdropping would require a
physical connection to your network.
Note: Actual data throughput will vary. Network conditions and environmental factors,
including volume of network traffic, building materials and construction, and
network overhead, can lower actual data throughput rate.
Assessing Your Speed Requirements
Because your Internet connection is likely to operate at a much lower speed than your local
network, faster local networking technologies might not improve your Internet experience.
However, many emerging home applications require high data rates. For example:
•
Streaming HD video requires 10 to 30 Mbps per stream. Because latency and packet loss can
disrupt your video, plan to provide at least twice the capacity you need.
•
Streaming MP3 audio requires less than 1 Mbps per stream and does not strain most modern
networks. Like video, however, streaming audio is also sensitive to latency and packet loss, so
a congested network or a noisy link can cause problems.
Fine-Tuning Your Network
6-2
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
•
Backing up computers over the network has become popular due to the availability of
inexpensive mass storage. Table 6-1 shows approximate, comparative times for transferring 1
gigabyte (1 GB) of data using various networking technologies.
Table 6-1. Theoretical Transfer Time for 1 Gigabyte
Network Connection
Theoretical Raw Transfer Time
Gigabit wired Ethernet
802.11n (40MHz) wireless
Powerline HD
8 seconds
26 seconds
40 seconds
100 Mbps wired Ethernet
802.11n (20MHz) wireless
802.11g wireless
80 seconds
55 seconds
150 seconds
700 seconds
800 seconds
2700 seconds
144,000 seconds (40 hours)
802.11b wireless
10 Mbps wired Ethernet
Cable modem (3 Mbps)
Analog modem (56 kbps)
Optimizing Your Network Bandwidth
As your network grows, it might consist of several segments of different networking technologies,
each providing different throughput. In planning your network, you should first consider which
devices will have the heaviest traffic flow between them. Examples are:
•
•
A media center in one room streaming high-definition video from a server in another room
A storage device that is used for backing up your computers
Fine-Tuning Your Network
6-3
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Next, consider the throughput of your network devices. Where possible, make the heaviest-traffic
connections using higher-speed technologies, with no lower-speed bottlenecks in the path.
Figure 6-1
Figure 6-1 shows a sample network using multiple networking technologies. In this network, the
two PCs with Gigabit (1000 Mbps) Ethernet adapters have a gigabit connection through the GS605
switch to the storage server. This connection should allow for extremely fast backups or quick
access to large files on the server. The PC connected through a pair of Powerline HD adapters is
limited to the 200 Mbps speed of the Powerline HD connection. Although any of the links in this
example would be sufficient for high-traffic applications such as streaming HD video, the use of
older devices such as 10 Mbps Ethernet or 802.11b wireless would create a significant bottleneck.
Fine-Tuning Your Network
6-4
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Optimizing Wireless Performance
The speed and operating distance or range of your wireless connection can vary significantly based
on the physical placement of the wireless router. You should choose a location for your router that
will maximize the network speed.
Note: Failure to follow these guidelines can result in significant performance degradation
or inability to wirelessly connect to the router. For complete range and
performance specifications, click the link to the online document “Wireless
The following list describes how to optimize wireless router performance.
•
Identify critical wireless links.
If your network has several wireless devices, decide which wireless devices need the highest
data rate, and locate the router near them. Many wireless products have automatic data-rate
fallback, which allows increased distances without loss of connectivity. This also means that
devices that are farther away might be slower. Therefore, the most critical links in your
network are those where the traffic is high and the distances are great. Optimize those first.
•
Choose placement carefully.
For best results, place your router:
–
–
Near the center of the area in which your computers will operate.
In an elevated location such as a high shelf where the wirelessly connected computers
have line-of-sight access (even if through walls).
–
–
Avoid obstacles to wireless signals.
Keep wireless devices at least 2 feet from large metal fixtures such as file cabinets,
refrigerators, pipes, metal ceilings, reinforced concrete, and metal partitions.
–
Keep away from large amounts of water such as fish tanks and water coolers.
•
Reduce interference.
–
–
Avoid windows unless communicating between buildings.
Place wireless devices away from various electromagnetic noise sources, especially those
in the 2400–2500 MHz frequency band. Common noise-creating sources are:
•
•
Computers and fax machines (no closer than 1 foot)
Copying machines, elevators, and cell phones (no closer than 6 feet)
Fine-Tuning Your Network
6-5
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
•
Microwave ovens (no closer than 10 feet)
•
Choose your settings.
–
Use a scanning utility to determine what other wireless networks are operating nearby, and
choose an unused channel.
–
Turn off SSID broadcast, and change the default SSID. Other nearby devices might
automatically try to connect to your network several times a second, which can cause
significant performance reduction.
•
Use WMM to improve the performance of voice and video traffic over the wireless link.
Changing the MTU Size
The Maximum Transmission Unit (MTU) is the largest data packet a network device transmits.
When one network device communicates across the Internet with another, the data packets travel
through many devices along the way. If any device in the data path has a lower MTU setting than
the other devices, the data packets must be split or “fragmented” to accommodate the one with the
smallest MTU.
The best MTU setting for NETGEAR equipment is often just the default value, and changing the
value might fix one problem but cause another. Leave MTU unchanged unless one of these
situations occurs:
•
You have problems connecting to your ISP, or other Internet service, and either the technical
support of the ISP or of NETGEAR recommends changing the MTU size. These might require
an MTU change:
–
–
–
–
A secure Web site that will not open, or displays only part of a Web page
Yahoo e-mail
MSN
America Online’s DSL service
•
•
You use VPN and have severe performance problems.
You used a program to optimize MTU for performance reasons, and now you have
connectivity or performance problems.
Note: An incorrect MTU setting can cause Internet communication problems such as the
inability to access certain Web sites, frames within Web sites, secure login pages,
or FTP or POP servers.
Fine-Tuning Your Network
6-6
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
If you suspect an MTU problem, a common solution is to change the MTU size to 1400. If you are
willing to experiment, you can gradually reduce the MTU size from the maximum value of 1500
Table 6-2. Common MTU Sizes
MTU
Application
1500
The largest Ethernet packet size and the default value. This is the typical setting for non-
PPPoE, non-VPN connections, and is the default value for NETGEAR routers, adapters,
and switches.
1492
1472
1468
1460
1436
1400
576
Used in PPPoE environments.
Maximum size to use for pinging. (Larger packets are fragmented.)
Used in some DHCP environments.
Usable by AOL if you do not have large e-mail attachments, for example.
Used in PPTP environments or with VPN.
Maximum size for AOL DSL.
Typical value to connect to dial-up ISPs.
To change the MTU size:
1. In the main menu, under Advanced, select WAN Setup.
2. In the MTU Size field, enter a new size between 64 and 1500.
3. Click Apply to save the new configuration.
Quality of Service
Quality of Service (QoS) is an advanced feature that can be used to prioritize some types of traffic
ahead of others. The WNR3500L router can provide QoS prioritization over the wireless link and
on the Internet connection. To configure QoS, use the QoS Setup screen.
Fine-Tuning Your Network
6-7
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
From the main menu of the browser interface, under Advanced, select QoS Setup. The QoS Setup
screen displays:
Figure 6-2
Using WMM QoS for Wireless Multimedia Applications
The WNR3500L router supports Wi-Fi Multimedia Quality of Service (WMM QoS) to prioritize
wireless voice and video traffic over the wireless link. WMM QoS provides prioritization of
wireless data packets from different applications based on four access categories: voice, video,
best effort, and background. For an application to receive the benefits of WMM QoS, both it and
the client running that application must be WMM enabled. Legacy applications that do not support
WMM, and applications that do not require QoS, are assigned to the best effort category, which
receives a lower priority than voice and video.
WMM QoS is enabled by default. You can disable it in the QoS Setup screen, shown in Figure 6-2
on page 6-8, by clearing the Enable WMM check box and clicking Apply.
Configuring QoS for Internet Access
You can give prioritized Internet access to the following types of traffic:
•
•
•
•
For specific applications
For specific online games
On individual Ethernet LAN ports of the router
From a specific device by MAC address
Fine-Tuning Your Network
6-8
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
To specify prioritization of traffic, you must create a policy for the type of traffic and add the
policy to the QoS Policy table in the QoS Setup screen. For convenience, the QoS Policy table lists
many common applications and online games that can benefit from QoS handling.
QoS for Applications and Online Gaming
To create a QoS policy for applications and online games:
1. From the main menu, under Advanced, select QoS Setup. The QoS Setup screen displays, as
shown in Figure 6-2 on page 6-8.
2. Click Setup QoS Rule. The QoS Priority Rule List displays:
Figure 6-3
3. In the QOS Priority Rule List, select an existing item, or you can scroll to the bottom of the list
and select Add Priority Rule.
Fine-Tuning Your Network
6-9
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
a. If you chose to add a new entry, the screen expands as shown:
Figure 6-4
b. In the QoS Policy for field, enter a descriptive name for the new application or game.
c. Select the packet type, either TCP, UDP, or both (TCP/UDP), and specify the port
number or range of port numbers used by the application or game.
4. From the Priority drop-down list, select the priority that this traffic should receive relative to
other applications and traffic when accessing the Internet. The options are Low, Normal, High,
and Highest.
5. Click Apply to save this rule to the QoS Policy list and return to the QoS Setup screen.
6. In the QoS Setup screen, select the Turn Internet Access QoS On check box.
7. Click Apply.
QoS for a Router LAN Port
To create a QoS policy for a device connected to one of the router’s LAN ports:
1. From the main menu, under Advanced, select QoS Setup. The QoS Setup screen displays, as
shown in Figure 6-2 on page 6-8.
2. Click Setup QoS Rule and then click Add Priority Rule.
Fine-Tuning Your Network
6-10
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
3. On the QoS - Priority Rules screen, go to the Priority Category field, and select Ethernet
LAN Port from the drop-down list:
Figure 6-5
4. From the LAN port list, select the LAN port that will have a QoS policy.
5. From the Priority drop-down list, select the priority that this port’s traffic should receive
relative to other applications and traffic when accessing the Internet. The options are Low,
Normal, High, and Highest.
6. Click Apply to save this rule to the QoS Policy list and return to the QoS Setup screen.
7. Click Apply.
QoS for a MAC Address
To create a QoS policy for traffic from a specific MAC address:
1. From the main menu, under Advanced, select QoS Setup. The QoS Setup screen displays, as
shown in Figure 6-2 on page 6-8.
2. Click Setup QoS Rule and then click Add Priority Rule.
Fine-Tuning Your Network
6-11
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
3. On the QoS - Priority Rules screen, go to the Priority Category field, and select MAC
Address from the drop-down list:
Figure 6-6
4. If the device to be prioritized appears in the MAC Device List, select it. The information from
the MAC Device List is used to populate the policy name, MAC Address, and Device Name
fields. If the device does not appear in the MAC Device List, click Refresh. If it still does not
appear, you must complete these fields manually.
5. From the Priority drop-down list, select the priority that this device’s traffic should receive
relative to other applications and traffic when accessing the Internet. The options are Low,
Normal, High, and Highest.
6. Click Apply to save this rule to the QoS Policy list and return to the QoS Setup screen.
7. Click Apply.
Editing or Deleting an Existing QoS Policy
To edit or delete an existing QoS policy:
1. From the main menu, under Advanced, select QoS Setup. The QoS Setup screen displays, as
shown in Figure 6-2 on page 6-8.
2. Click Setup QoS Rule.
3. Select the radio button next to the QoS policy to be edited or deleted, and do one of the
following:
•
•
Click Delete to remove the QoS policy.
Click Edit to edit the QoS policy. Follow the instructions in the preceding sections to
change the policy settings.
Fine-Tuning Your Network
6-12
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
4. Click Apply in the QoS Setup screen to save your changes.
Using Universal Plug and Play
Universal Plug and Play (UPnP) helps devices, such as Internet appliances and computers, to
access the network and connect to other devices as needed. UPnP devices can automatically
discover the services from other registered UPnP devices on the network.
Note: If you use applications such as multiplayer gaming, peer-to-peer connections, real-
time communications such as instant messaging, or remote assistance (a feature in
Windows XP), you should enable UPnP.
To turn on Universal Plug and Play:
1. From the main menu of the browser interface, under Advanced, click UPnP. The UPnP screen
displays.
Figure 6-7
2. The available settings and displays in this screen are:
•
Turn UPnP On. UPnP can be enabled or disabled for automatic device configuration. The
default setting for UPnP is enabled. If this check box is not selected, the router does not
allow any device to automatically control the resources, such as port forwarding
(mapping) of the router.
•
Advertisement Period. The advertisement period is how often the router broadcasts its
UPnP information. This value can range from 1 to 1440 minutes. The default period is 30
minutes. Shorter durations ensure that control points have current device status at the
expense of additional network traffic. Longer durations might compromise the freshness
of the device status but can significantly reduce network traffic.
Fine-Tuning Your Network
6-13
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
•
•
Advertisement Time To Live. The time to live for the advertisement is measured in hops
(steps) for each UPnP packet sent. The time to live hop count is the number of steps a
multicast packet is allowed to propagate for each UPnP advertisement before it
disappears. The number of hops can range from 1 to 255. The default value for the
advertisement time to live is 4 hops, which should be fine for most home networks. If you
notice that some devices are not being updated or reached correctly, then it might be
necessary to increase this value.
UPnP Portmap Table. The UPnP Portmap Table displays the IP address of each UPnP
device that is currently accessing the router and which ports (Internal and External) that
device has opened. The UPnP Portmap Table also displays what type of port is open and
whether that port is still active for each IP address.
3. Click Apply to save your settings.
Fine-Tuning Your Network
6-14
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Chapter 7
USB Storage
This chapter describes how to access and configure a USB storage drive attached to your router.
Note: The USB port on the router can be used only to connect USB storage devices like
flash drives or hard drives. Do not connect computers, USB modems, printers, CD
drives, or DVD drives to the router USB port.
This chapter includes the following sections:
•
•
•
•
•
•
•
•
•
USB Drive Requirements
The router works with 1.0 and 1.1 (USB Full Speed) and 2.0 (USB High Speed) standards. The
approximate USB bus speeds are shown below.
Bus
Speed/Sec
USB 1.1
USB 2.0
12 Mbits
480 Mbits
USB Storage
7-1
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Actual bus speeds can vary, depending on the CPU speed, memory, speed of the network, and
other variables.
The router should work with most USB-compliant external flash and hard drives. For the most up-
to-date list of USB drives supported by the router, go to: http://kb.netgear.com/app/answers/detail/
/a_id/11280.
The router supports both READ and WRITE for FAT16, FAT32, and NTFS.
Note: Some USB external hard drives and flash drives require drivers to be loaded in to
the PC before the PC can access the USB device. Such USB devices will not work
with the WNR3500L router.
File Sharing Scenarios
You can share files on the USB drive for a wide variety of business and recreational purposes. The
files can be any PC, Mac, or Linux file type including text files, Word, PowerPoint, Excel, MP3.
pictures, and multimedia. USB drive applications include:
•
Sharing multimedia with friends and family—sharing MP3 files, pictures, and other
multimedia with local and remote users.
•
Sharing resources on your network—storing files in a central location so that you do not have
to power up a computer to perform local sharing. In addition, you can share files between
Macintosh, Linux, and PC computers by using the USB drive as a go-between across the
systems.
•
Sharing files with offsite coworkers—sharing files such as Word documents, PowerPoint
presentations, and text files with remote users.
A few common uses are described in the following sections.
Sharing Photos with Friends and Family
You can create your own central storage location for photos and multimedia. This eliminates the
need to log in to (and pay for) an external photo sharing site.
To share files with your friends and family:
1. Insert your USB drive into the USB port on the router either directly or with a USB cable.
Computers on your local area network (LAN) can automatically access this USB drive using a
Web browser or Microsoft Networking.
USB Storage
7-2
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Storing Files in a Central Location for Printing
This scenario is for a family that has one high quality color printer directly attached to a PC, but
not shared on the local area network (LAN). This family does not have a print server:
•
•
The daughter has some photos on her Macintosh computer that she wants to print.
The mother has a photo-capable color printer directly attached to her PC, but not shared on the
network.
•
The mother and daughter’s computers are not visible to each other on the network.
How can the daughter print her photos on the color printer attached to her mother’s PC? This is
where the USB drive on the router can save you time and effort.
1. The daughter accesses the USB drive by typing \\readyshare in the address field of her Web
browser. Then she copies the photos to the USB drive.
2. The mother uses her Web browser or Microsoft Networking to transfer the files from the USB
drive to the PC. Then she prints the files.
Sharing Large Files with Colleagues
Sending files that are larger than 5 MB can pose a problem for many e-mail systems. The router
allows you to share very large files such as PowerPoint presentations or ZIP files with colleagues
at another site. Rather than filling up their mail systems with large files, your colleagues can use
FTP to easily download shared files from the router.
Sharing files with a remote colleague involves the following considerations:
•
There are two user accounts: admin and guest.
Note: The password for admin is the same one that you use to access the router. By
default, it is password. The guest user account has no password.
•
On the FTP site, your colleagues should use the guest user account. No password is required
for guest.
USB Storage
7-3
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
•
Be sure to enable either FTP (via Internet) in the USB Storage (Advanced Settings) screen.
This option supports both downloading and uploading of files. See “Configuring USB Storage
Note: You can also enable the HTTP (via Internet) option on the USB Storage
(Advanced Settings) screen to share large files. This option supports
downloading files only. See “Configuring USB Storage Advanced Settings” on
USB Storage Basic Settings
You can view or edit basic settings for the USB storage device attached to your router. On the
router main menu below the USB Storage heading, select Basic Settings. The following screen
displays:
Figure 7-1
By default, the USB storage device is available to all computers on your local area network
(LAN). To access your USB device from this screen, you can click the Network/Device Name or
the Share Name.
USB Storage
7-4
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Alternately, you can also type \\readyshare in the address field of your Web browser.
Note: If you logged in to the router before you connected your USB device, you might
not see your USB device in the router screens until you log out and then log back in
again.
The following table explains the fields and buttons in this screen:.
Table 7-1. USB Storage Basic Settings
Fields and Buttons
Description
Network Device Name
The default is \\readyshare. This is the name used to access the
USB device connected to the router.
Available Network
folders
Share Name
If only 1 device is connected, the default share name is
USB_Storage. You can click the name shown or you can type it in
the address field of your Web Browser. If Not Shared is shown, the
default share has been deleted and no other share for the root
folder exists. Click the Edit button to change this setting.
Read/Write
Access
Shows the permissions/access controls on the network folder: All –
no password (the default) allows all users to access the network
folder. The user name (account name) for All – no password is
guest. The password for admin is the same one that you use to
log in to the router main menu. By default, it is password.
Folder Name
Volume Name
Full path used by the network folder:
Volume name from the storage device (either USB drive or HDD).
Shows the current utilization of the storage device.
Total/Free
Space
Edit button
Click the Edit button to edit the Available Network folder settings.
Safely Remove USB Device button
Click to safely remove the USB device attached to your router. See
USB Storage
7-5
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Editing a Network Folder
On the USB Storage (Advanced Settings) screen, click the Edit button to open the Edit Network
Folder screen.
Figure 7-2
You can use this screen to select a folder, change the Share Name, or change the Read Access or
Write Access from All – no password to admin. The user name (account name) for All – no
password is guest. The password for admin is the same one that is used to log in to the router
main menu. By default, it is password.
Note: You must click Apply in order for your changes to take effect.
USB Storage
7-6
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Configuring USB Storage Advanced Settings
To configure advanced USB settings, under the USB heading on the router main menu, select
Advanced Settings. The USB Storage (Advanced Settings) screen displays.
Figure 7-3
You can use this screen to specify access to the USB storage device. The following table explains
the fields and buttons in the USB Storage Advanced Settings screen.
Table 7-2. USB Storage Advanced Settings
Fields and Buttons
Description
Network Device Name
The default is readyshare. This is the name used to access the
USB device connected to the router. The name works only in an
operating system that supports NetBIOS, such as Microsoft
Windows.
USB Storage
7-7
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Table 7-2. USB Storage Advanced Settings
Fields and Buttons
Description
Workgroup
If you are using a Windows Workgroup rather than a domain, the
Workgroup name is displayed here. The name only works in an
operating system that supports NETBIOS like Microsoft Windows.
Access Method Network
Enabled by default, this connection allows all users on the LAN to
have access to the USB drive.
Connection
HTTP
Disabled by default. If you enable this setting, you can type http://
readyshare (http://readyshare.routerlogin.net/shares) to access
the USB drive.
HTTP (via internet) Disabled by default. If you enable this setting, remote users can
type http://public IP address/shares (for example, http://
1.1.10.102/shares) or a URL domain name to access the USB
drive over the Internet. This setting supports file uploading only.
FTP
Disabled by default.
FTP (via internet)
Disabled by default. If you enable this setting, remote users can
access the USB drive via FTP over the Internet. This setting
supports both downloading and uploading of files.
Available
Share Name
If only 1 device is connected, the default share name is
Network Folders
USB_Storage. You can click the name shown or you can type it in
the address field of your Web Browser. If Not Shared is shown, the
default share has been deleted and no other share for the root
folder exists. Click the Edit button to change this setting.
Read/Write Access Shows the permissions/access controls on the network folder: All -
no password (the default) allows all users to access the network
folder. The password for admin is the same one that you use to log
in to the router main menu.
Folder Name
Full path used by the network folder:
Volume Name
Total/Free Space
Volume name from the storage device (either USB drive or HDD).
Shows the current utilization of the storage device.
USB Storage
7-8
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Creating a Network Folder
From the USB Storage (Advanced Settings) screen, click the Create a Network Folder button to
open the Create a Network Folder screen:
Figure 7-4
You can use this screen to create a folder and to specify its Share Name, Read Access, and Write
Access from All - no password to admin. The user name (account name) for All – no password
is guest. The password for admin is the same one that is used to log in to the router main menu.
By default, it is password.
Note: You must click Apply in order for your changes to take effect.
USB Storage
7-9
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
ReadyShare Access
Once you have set up your router, you can connect any USB storage device and share the contents
with other users on your network.
You can access your USB device in any of the following ways:
•
On Windows 7, Windows XP, Windows Vista, and Windows 2000 systems, select Start > Run
and enter \\readyshare in the dialog box. Click OK.
•
On Windows 7, Windows XP, Windows Vista, and Windows 2000 systems, open Explorer or
Safari, and enter \\readyshare in the Address Bar.
•
•
On Mac OS X (version 10.2 or later), enter smb://readyshare in the Address Bar.
In My Network Places, enter \\readyshare in the Address Bar.
You can also use the ReadyShareConnect utility to automatically map your USB drive on
Windows 7, Windows XP, Windows Vista, and Windows 2000 systems:
1. Copy ReadyShareConnect from your Resource CD to your PC, and click
ReadyShareConnect.exe.
2. The Windows Map Network Drive dialog box opens and displays the Folder name:
\\readyshare\USB_Storage. Select a drive from the Drive dialog box and click Finish.
Unmounting a USB Drive
To unmount a USB disk drive so that no users can access it, from the USB Settings screen, click
the Safely Remove USB button. This takes the drive offline.
USB Storage
7-10
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Specifying Approved USB Devices
For more security, you can set up the router to share approved USB devices only.
1. Select USB Settings from the Advanced menu, and then click Approved Devices. The USB
Drive Approved Settings screen displays:
Figure 7-5
2. Select the USB device from the Available USB Devices list.
3. Click Add.
4. Select the Allow only approved devices check box.
5. Click Apply so that your change takes effect.
If you want to approve another USB device, you must first use the Safely Remove USB Device
button to unmount the currently connected USB device. Connect the other USB device, and then
repeat this process.
USB Storage
7-11
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Connecting to the USB Drive from a Remote Computer
To connect to the USB drive from remote computers using a Web browser, you must use the
router’s Internet port IP address. If you are using dynamic DNS, you can type the DNS name,
rather than the IP address.
Locating the Internet Port IP Address
The Router Status screen shows the Internet port IP address:
1. Log in to the router.
2. Under the Maintenance section in the left navigator, click Router Status.
3. Record the IP address that is listed for the Internet Port. This is the IP address you can use to
connect to the router remotely.
Accessing the Router’s USB Drive Remotely Using FTP
You can connect to the router’s USB drive using a Web browser:
1. Connect to the router by typing ftp:// and the Internet port IP address in the address field of
Internet Explorer or Netscape Navigator. For example,
ftp://206.82.202.46/shares
If you are using dynamic DNS, you can type the DNS name, rather than the IP address.
2. Type the account name and password that has access rights to the USB drive. The user name
(account name) for All – no password is guest.
3. The directories of the USB drive that your account has access to will be displayed, for
example, share/partition1/directory1. You can now read and copy files from the USB
directory.
Connecting to the USB Drive with Microsoft Network
Settings
You can access the USB drive from local computers on your home or office network using
Microsoft network settings. You must be running Microsoft Windows 2000, XP, or older versions
of Windows with Microsoft networking enabled. You can use normal Explorer operations, such as
drag and drop, file open, or cut/paste files from:
USB Storage
7-12
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
•
•
•
Microsoft Windows Start Menu, Run option
Windows Explorer
Network Neighborhood or My Network Place.
Enabling File and Printer Sharing
Each computer’s network properties must be set to enable network communication with the USB
drive. File and Printer Sharing for Microsoft Networks must be enabled, as described below.
Note: In Windows 2000 and Windows XP, File and Printer Sharing is enabled by default.
Configuring Windows 98SE and Windows ME
The easiest way to get to your network properties is to go to your desktop, right-click Network
Neighborhood and then click Properties. File and printer sharing for Microsoft Windows should be
listed. If not, click Add and follow the installation prompts.
Note: If you have any questions on File and Printer Sharing, please contact Microsoft for
assistance.
Configuring Windows 2000 and Windows XP
Right-click on the network connection for your local area network. File and Printer Sharing for
Microsoft Windows should be listed. If not, click Install and follow the installation prompts.
USB Storage
7-13
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8
Troubleshooting
This chapter provides information about troubleshooting your RangeMax Wireless-N Gigabit
Router with USB WNR3500L. After each problem description, instructions are provided to help
you diagnose and solve the problem. As a first step, please review the Quick Tips.
Tip: NETGEAR provides helpful articles, documentation, and the latest software
This chapter includes the following sections:
•
•
•
•
•
•
•
•
Quick Tips
This section describes tips for troubleshooting some common problems.
Table 8-1. Quick Tips
Recommendation
Instructions
Be sure to restart your network in this sequence.
1. Turn off and unplug the modem.
2. Turn off the wireless router and computers.
3. Plug in the modem and turn it on. Wait 2 minutes.
4. Turn on the wireless router and wait 2 minutes.
5. Turn on the computers.
8-1
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Table 8-1. Quick Tips (continued)
Recommendation
Instructions
Make sure that the Ethernet cables are securely
plugged in.
• The Internet status light on the wireless router is on
if the Ethernet cable connecting the wireless router
and the modem is plugged in securely and the
modem and wireless router are turned on.
• For each powered-on computer connected to the
wireless router by an Ethernet cable, the
corresponding numbered router LAN port light is
on.
Make sure that the wireless settings in the computer • For a wirelessly connected computer, the wireless
and router match exactly.
network name (SSID) and wireless security
settings of the router and wireless computer must
match exactly.
• If you set up an Access List in the Advanced
Wireless Settings screen, you must add each
wireless computer’s MAC address to the router’s
access list.
Make sure that the network settings of the computer • Wired and wirelessly connected computers must
are correct.
have network (IP) addresses on the same network
as the router. The simplest way to do this is to
configure each computer to obtain an IP address
automatically using DHCP. Click the link to the
online document “Preparing Your Network” in
Appendix B, or see the documentation that came
with your computer.
• Some cable modem service providers require you
to use the MAC address of the computer initially
registered on the account. You can view the MAC
address in the Attached Devices screen.
Check the Power light to verify correct router
operation.
If the Power light does not turn off within 2 minutes
after you turn the router on, reset the router
according to the instructions in “Restoring the Default
Troubleshooting
8-2
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Troubleshooting Basic Functions
After you turn on power to the router, the following sequence of events should occur:
1. When power is first applied, verify that the Power light
2. After approximately 1 minute, verify that:
a. The Power light is solid green.
is on.
b. The Internet light is on if the Internet port is connected.
c. A numbered LAN port light is on for any local port that is connected to a computer. This
indicates that a link has been established to the connected device.
If any of the above conditions does not occur, see the following table.
Table 8-2. Troubleshooting LED Behavior
Situation
Recommended Action
Power light is off.
Check the following:
• Make sure that the power cord is properly connected to your router
and that the power adapter is properly connected to a functioning
power outlet.
• Check that you are using the power adapter supplied by NETGEAR
for this product.
If the error persists, you have a hardware problem and should contact
technical support.
Power light stays amber.
When the router is turned on, the Power light turns amber for about 60
seconds and then turns green. If the light does not turn green, the
router has a problem.
If the Power light is still amber 2 minutes after turning on power to the
router:
1. Turn the power off and back on to see if the router recovers.
2. Clear the router’s configuration to factory defaults. This will set the
router’s IP address to www.routerlogin.net. This procedure is
If the error persists, you might have a hardware problem and should
contact technical support.
Troubleshooting
8-3
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Table 8-2. Troubleshooting LED Behavior (continued)
Situation
Recommended Action
Power light blinks green slowly
and continuously. The wireless
router firmware is corrupted.
Restore the wireless router firmware:
1. Make sure that your PC is connected to your wireless router and
the wireless router is powered on.
2. Insert the Resource CD that came with your router into your PC.
The CD automatically starts and detects the language you are using
on your PC. Select a different language option, if you prefer. If the
CD does not automatically start, browse the CD and double-click
.
3. From the CD menu, select Supporting Software, then Netgear
Firmware Recovery Utility, and follow the prompts for the
recovery process.
4. After firmware recovery is complete, follow the prompts to restore
your configuration.
The firmware recovery utility places a Netgear Router Recovery
shortcut on the desktop.
Internet light stays amber.
When the router is turned on, the Internet light turns amber for about 60
seconds and then turns green. If the light does not turn green, the
router has a problem.
If the Internet light is still amber 2 minutes after turning on power to the
router:
1. The Internet is not accessible. Confirm that you have the correct
internet setting.
2. Clear the router’s configuration to factory defaults. This will set the
router’s IP address to www.routerlogin.net. This procedure is
3. Turn the power off and back on to see if the router recovers.
Check the following:
WPS push-button blinks green
after setting WPS security.
2. Check that PIN verification has succeeded for the WPS-enabled
device you are connecting to the router.
3. Make sure you have not pushed the push-button after disabling the
WPS function (you logged into the router and disabled this
previously).
4. Check that the router is not in the temporary AP setup locked state
(if you are using the wireless repeater function).
Troubleshooting
8-4
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Table 8-2. Troubleshooting LED Behavior (continued)
Situation
Recommended Action
Lights never turn off.
When the router is turned on, the Power LED does not go off. The WAN
and LAN port LEDs come on after about 10 seconds if the ports are
connected.
If all lights are still on 1 minute after power up:
• Cycle the power to see if the router recovers.
• Clear the router’s configuration to factory defaults as explained in
If the error persists, you might have a hardware problem and should
The Internet or Ethernet port lights If either the Ethernet port lights or the Internet light does not light when
are off.
the Ethernet connection is made, check the following:
• Make sure that the Ethernet cable connections are secure at the
router and at the modem or computer.
• Make sure that power is turned on to the connected modem or
computer.
• Be sure that you are using the correct cable:
When connecting the router’s Internet port to a cable or DSL modem,
be sure to use the yellow Ethernet cable that was supplied with your
NETGEAR wireless router.
Wireless light is off.
If the Wireless light does not come on, verify that the Enable Wireless
Router Radio check box is selected in the Advanced Wireless Settings
Cannot Access the Router Main Menu
If you are unable to access the router’s main menu from a computer on your local network, check
the following:
•
•
If you are connecting from a wireless computer, try connecting from a wired computer.
Check the Ethernet connection between the wired computer and the router as described in
Troubleshooting
8-5
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
•
Make sure that your computer’s IP address is on the same subnet as the router. For
configure your computer.
Note: If your computer’s IP address is shown as 169.254.x.x: Windows and Mac OS
generate and assign an IP address if the computer cannot reach a DHCP server.
These autogenerated addresses are in subnet 169.254.x.x. If your IP address is
in this range, check the connection from the computer to the router, and reboot
your computer.
•
Make sure that your browser has Java, JavaScript, or ActiveX enabled. If you are using
Internet Explorer, click Refresh to be sure that the Java applet is loaded.
•
•
Try closing the browser and opening it again, or try a different browser.
Make sure that you are using the correct login information. The factory default login name is
admin, and the password is password. Make sure that Caps Lock is off when entering this
information.
If the router does not save changes you have made in the Web Configuration Interface, check the
following:
•
When entering configuration settings, be sure to click Apply before moving to another screen
or tab, or your changes could be lost.
•
Click Refresh or Reload in the Web browser. The changes might have occurred, but the Web
browser might be caching the old configuration.
Cannot Access the Internet
If you can access your router but you are unable to access the Internet, you should first determine
whether the router can obtain an IP address from your Internet Service Provider (ISP). Unless your
ISP provides a static IP address, your router must request an IP address from the ISP. You can
determine whether the request was successful using the Web Configuration Manager.
To check the WAN IP address:
3. Under Maintenance, select Router Status.
Troubleshooting
8-6
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
4. Check that an IP address is shown for the Internet port. If 0.0.0.0 is shown, your router has not
obtained an IP address from your ISP.
If your router is unable to obtain an IP address from the ISP, you might need to force your cable or
DSL modem to recognize your new router by restarting your network, as described in Table 8-1 on
page 8-1.
If your router is still unable to obtain an IP address from the ISP, the problem might be one of the
following:
•
Your ISP might require a login program.
Ask your ISP whether they require PPP over Ethernet (PPPoE) or some other type of login.
•
•
If your ISP requires a login, the login name or password might be set incorrectly.
Your ISP might check for your computer’s host name.
Assign the computer host name of your ISP account as the account name in the Basic Settings
screen.
•
Your ISP allows only one Ethernet MAC address to connect to Internet and might check for
your computer’s MAC address. In this case, do one of the following:
–
Inform your ISP that you have bought a new network device, and ask them to use the
router’s MAC address.
–
Configure your router to spoof your computer’s MAC address. This procedure is
If your router can obtain an IP address, but your computer is unable to load any Web pages from
the Internet:
•
Your computer might not recognize any DNS server addresses.
A DNS server is a host on the Internet that translates Internet names (such as www addresses)
to numeric IP addresses. Typically, your ISP provides the addresses of one or two DNS servers
for your use. If you entered a DNS address during the router’s configuration, reboot your
computer, and verify the DNS address as described in the online document you can access
manually with DNS addresses, as explained in your operating system documentation.
•
•
Your computer might not have the router configured as its TCP/IP gateway.
If your computer obtains its information from the router by DHCP, reboot the computer, and
verify the gateway address as described in the online document you can access from
You might be running login software that is no longer needed.
Troubleshooting
8-7
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
If your ISP provided a program to log you in to the Internet (such as WinPoET), you no longer
need to run that software after installing your router. You might need to go to Internet Explorer
and select Tools > Internet Options, click the Connections tab, and select Never dial a
connection.
Troubleshooting a Network Using the Ping Utility
Most network devices and routers contain a ping utility that sends an echo request packet to the
designated device. The device then responds with an echo reply. Troubleshooting a network is
made very easy by using the ping utility in your computer or workstation.
Testing the LAN Path to Your Router
You can ping the router from your computer to verify that the LAN path to your router is set up
correctly.
To ping the router from a running Windows PC:
1. From the Windows toolbar, click Start, and then select Run.
2. In the field provided, type ping followed by the IP address of the router, as in this example:
ping www.routerlogin.net
3. Click OK.
You should see a message like this one:
Pinging <IP address > with 32 bytes of data
If the path is working, you see this message:
Reply from < IP address >: bytes=32 time=NN ms TTL=xxx
If the path is not working, you see this message:
Request timed out
If the path is not functioning correctly, you could have one of the following problems:
•
Wrong physical connections
–
For a wired connection, make sure that the numbered LAN port light is on for the port
to which you are connected. If the light is off, follow the instructions in Table 8-2 on
page 8-3.
Troubleshooting
8-8
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
–
Check that the corresponding Link lights are on for your network interface card. If
your router and computer are connected to a separate Ethernet switch, make sure that
the Link lights are on for the switch ports that are connected to your computer and
router.
•
Wrong network configuration
–
Verify that the Ethernet card driver software and TCP/IP software are both installed
and configured on your computer.
–
Verify that the IP address for your router and your computer are correct and that the
addresses are on the same subnet.
Testing the Path from Your Computer to a Remote Device
After verifying that the LAN path works correctly, test the path from your computer to a remote
device.
1. From the Windows toolbar, click the Start button, and then select Run.
2. In the Windows Run window, type:
ping -n 10 <IP address>
where <IP address> is the IP address of a remote device such as your ISP’s DNS server.
If the path is functioning correctly, replies like those shown in the previous section are displayed.
If you do not receive replies:
•
•
Click Start > Run. Then type cmd, and press Enter.
In the command prompt window, enter the command ipconfig. This will show the default
gateway, whether the PC is configured as a DHCP client or a static IP.
•
Verify that the IP address of the router is listed as the default gateway as described in the
•
•
Check that your cable or DSL modem is connected and functioning.
If your ISP assigned a host name to your computer, enter that host name as the account name
in the Basic Settings screen.
•
Your ISP could be rejecting the Ethernet MAC addresses of all but one of your computers.
Many broadband ISPs restrict access by allowing traffic only from the MAC address of your
broadband modem, but some ISPs additionally restrict access to the MAC address of a single
computer connected to that modem. If this is the case, you must configure your router to
“clone” or “spoof” the MAC address from the authorized computer. For more information, see
Troubleshooting
8-9
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Problems with Date and Time
Under Content Filtering in the main menu, select E-mail to display a screen that shows the current
date and time of day. The WNR3500L router uses the Network Time Protocol (NTP) to obtain the
current time from one of several network time servers on the Internet. Each entry in the log is
stamped with the date and time of day. Problems with the date and time function can include the
following:
•
Date shown is January 1, 2000.
Cause: The router has not yet successfully reached a network time server. Check that your
Internet access settings are correct. If you have just completed configuring the router, wait at
least 5 minutes, and check the date and time again.
•
Time is off by one hour.
Cause: The router does not adjust for daylight savings time. In the E-mail screen, select the
Adjust for Daylight Savings Time check box.
Wireless Connectivity
The first steps in solving wireless connection problems are these:
1. Using your wireless card’s setup utility program, make sure that your wireless card can find
your wireless router.
2. Configure and test with the simplest wireless connection possible, and then add security.
The topics in this section describe these steps.
Using Your Wireless Card Setup Program
When you install a NETGEAR wireless card in your computer, a Smart Wizard utility program is
installed that can provide helpful information about your wireless network. You can find this
program in your Windows Program menu or as an icon in your system tray. Other wireless card
manufacturers might include a similar program.
If you have no specific wireless card setup program installed, you can use the basic setup utility in
Windows by following these steps:
1. Open the Windows Control Panel, and double-click Network Connections.
2. In the LAN section, double-click Wireless Network Connection.
Troubleshooting
8-10
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Use the setup program to scan for available wireless networks. Look for a network name (SSID) of
NETGEAR or your custom SSID if you have changed it. If your wireless network does not appear,
check these conditions:
•
•
•
Is your router set to a wireless standard that is not supported by your wireless card? Check the
If your wireless network appears, but the signal strength is weak, check these conditions:
•
Is your router too far from your computer, or too close? Place your computer near the router,
but at least 6 feet away, and see whether the signal strength improves.
•
Is your wireless signal obstructed by objects between the router and your computer? See
If your wireless network appears and has good signal strength, configure your wireless card and
router for the simplest possible connection as described in the next section.
Setting Up and Testing Basic Wireless Connectivity
Note: If you use a wireless computer to change wireless settings, you might be
disconnected when you click Apply. Reconfigure your wireless adapter to match
the new settings, or access the wireless router from a wired computer to make any
further changes.
Follow these instructions to set up and test basic wireless connectivity. Once you have established
basic wireless connectivity, you can enable security settings appropriate to your needs.
Troubleshooting
8-11
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
1. Select Wireless Settings under Setup in the main menu of the WNR3500L router.
Figure 8-1
2. For the wireless network name (SSID), use the default name, or choose a suitable descriptive
name. In the Name (SSID) field, you can enter a value of up to 32 alphanumeric characters.
The default SSID is NETGEAR.
Note: The SSID is case-sensitive; NETGEAR is not the same as nETgear. Also, the
SSID of any wireless access adapters must match the SSID you specify in the
WNR3500L router. If they do not match, you will not get a wireless
connection to the WNR3500L router.
3. Select the region in which the wireless interface will operate.
4. Set the channel. The default channel is Auto.
Troubleshooting
8-12
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
This field determines which operating frequency is used. It should not be necessary to change
the wireless channel unless you notice interference problems with another nearby wireless
router or access point. Select a channel that is not being used by any other wireless networks
within several hundred feet of your router. For more information about the wireless channel
frequencies, click the link to the online document “Wireless Networking Basics” in
5. Set the mode to Up to 300Mbps.
6. For Security Options, select None.
7. Click Apply to save your changes.
Note: If you are configuring the router from a wireless computer and you change the
router’s SSID, channel, or security settings, you will lose your wireless
connection when you click Apply. You must then change the wireless settings
of your computer to match the router’s new settings.
8. Select Wireless Settings under Advanced in the main menu of the WNR3500L router.
Figure 8-2
Troubleshooting
8-13
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
9. Make sure that the Enable Wireless Router Radio and Enable SSID Broadcast check boxes
are selected.
10. Click Setup Access List.
11. Make sure that the Turn Access Control On check box is not selected.
12. Configure and test your wireless computer for wireless connectivity.
Program the wireless adapter of your computer to have the same SSID and channel that you
specified in the router, and disable encryption. Check that your computer has a wireless link
and can obtain an IP address by DHCP from the router.
Once your computer has basic wireless connectivity to the router, you can configure the advanced
wireless security functions of the computer and router (for more information about security, see
Restoring the Default Configuration and Password
You can restore the factory default configuration settings to reset the router’s user name to admin,
the password to password, and the IP address to www.routerlogin.net. This procedure erases
your current configuration, including your wireless security settings, and restores the factory
defaults.
You can erase the current configuration and restore factory defaults in two ways:
•
•
Use the restore factory settings button on the rear panel of the router. Use this method for cases
when the administration password or IP address is not known.
To restore the factory default configuration settings when you do not know the administration
password or IP address, you must use the restore settings button on the rear panel of the router.
1. Press and hold the restore settings button for 5 seconds.
2. Release the restore settings button, and wait for the router to reboot.
For more information about the factory default settings, see Appendix A, “Default Configuration
If the wireless router fails to restart, or the Power light continues to blink or turns solid amber, the
unit might be defective. If the error persists, you might have a hardware problem and should
Troubleshooting
8-14
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
Default Configuration and Technical
Specifications
This appendix provides factory default settings and technical specifications for the RangeMax
Wireless-N Gigabit Router with USB WNR3500L.
Table A-1. WNR3500L Router Default Configuration Settings
Feature
Default Setting
Router Login
Router login URL
http://www.routerlogin.net or
http://www.routerlogin.com
Login name (case-sensitive) printed on
product label
admin
Password (case-sensitive) printed on
product label
password
Internet Connection
WAN MAC address
MTU size
Default hardware address (on label)
1500
Local Network
Router LAN IP address printed on product label
(also known as Gateway IP address)
192.168.1.1
Router subnet
DHCP server
DHCP range
Time zone
255.255.255.0
Enabled
192.168.1.2 to 192.168.1.254
GMT – 8 (North America only; the time zone
varies by country and region)
Time zone adjusted for Daylight Saving Time
Disable Router’s PIN:
Disabled
No
Default Configuration and Technical Specifications
A-1
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Table A-1. WNR3500L Router Default Configuration Settings (continued)
Wireless
Wireless communication
Enabled
NETGEAR
SSID Name
Security
Disabled
All wireless stations allowed
Enabled
Wireless Access List (MAC Filtering)
Broadcast SSID
Country/Region
United States (North America only; otherwise
varies by country and region)
Auto *
RF Channel
Operating Mode
Data Rate
Up to 145 Mbps
Auto *
Output Power
Full
Firewall
Inbound (communications coming in from the Internet) Disabled (bars all unsolicited requests)
Outbound (communications going out to the Internet) Enabled (all)
*. Maximum Wireless signal rate derived from IEEE Standard 802.11 specifications. Actual throughput will vary. Network
conditions and environmental factors, including volume of network traffic, building materials and construction, and network
overhead lower actual data throughput rate.
Default Configuration and Technical Specifications
A-2
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
Technical Specifications
Table A-2. WNR3500v2 Router General Specifications
Feature General
Network Protocol and Standards Compatibility
Data and Routing Protocols TCP/IP, RIP-1, RIP-2, DHCP, PPPoE, PPTP, Bigpond, Dynamic
DNS, and UPnP
Power Adapter
North America
Australia
120V, 60 Hz, input
240V, 50 Hz, input
230V, 50 Hz, input
12V DC @ 1.0A, output
Europe, UK
All regions (output)
Physical
Dimensions
6.89" x 5.12" x 1.38"
175 x 130 x 35 mm
Weight
0.72 lbs.
0.33 kg
Environmental
Operating temperature
0 to 40 C (32º to 104º F)
Operating humidity
90% maximum relative humidity, noncondensing
Electromagnetic Emissions
Designed to conform to the
following standards
FCC Part 15 Class B
EN 55022/24 (CISPR 22/24) Class B
EN 60950 (CE LVD)
Interface Specifications
LAN
10BASE-T or 100BASE-Tx, RJ-45 or 1000BASE-T
10BASE-T or 100BASE-Tx, RJ-45 or 1000BASE-T
WAN
Default Configuration and Technical Specifications
v1.0, November 2009
A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B
Related Documents
This appendix provides links to reference documents you can use to gain a more complete
understanding of the technologies used in your NETGEAR product.
Document
Link
TCP/IP Networking Basics
Wireless Networking Basics
Preparing Your Network
Virtual Private Networking
Basics
Glossary
In addition, you can find initial setup instructions for your wireless router in the NETGEAR
Wireless Router Setup Manual.
Related Documents
B-1
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
blocking
access 3-4
A
access
blocking 3-4
remote 4-11
access control
C
ActiveX 8-6
adding
See also configuring
configuration
manual 1-6
configuration file
erasing 4-11
managing 4-9
configuring
See also adding
B
Index-1
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
D
F
factory default settings
listed A-1
restoring 8-14
firewalls
disabling 5-7
default factory settings
listed A-1
restoring 8-14
disabling
G
firewall 5-7
DNS server
primary 1-9
secondary 1-9
H
Domain Name Server (DNS) addresses
current 4-6
I
troubleshooting 8-7
DynDNS.org 5-5
Internet connection
troubleshooting 8-6
E
IP addresses
autogenerated 8-6
current 4-5
Index-2
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
reserved 5-4
J
multicasting 5-3
N
K
network
restarting 8-2
L
LAN port
O
settings 4-6
language, screen display 1-5
P
ping 8-8
logs
sending 3-10
viewing 3-9
M
MAC address
port forwarding
configuring 5-16
example 5-14
spoofing 1-9
MAC addresses
current 4-5
port triggering
configuring 5-18
example 5-13
Index-3
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax™ Wireless-N Gigabit Router with USB WNR3500L User Manual
S
screen display language 1-5
selecting 1-5
Q
specifications
general A-3
technical A-1
R
T
restoring
configuration 4-10
time-out
router
trademarks ii
troubleshooting 8-1
Index-4
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
|