Nostalgia Products Group, LLC
1471 Partnership Dr.
Green Bay, WI 54303-5685
Visit us online at
©2009 Nostalgia Products Group LLC
Rev. 8/18/09
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions
Read all of the instructions before using this appliance. When using this appliance, always
exercise basic safety precautions, including the following:
1. Use this appliance only for its intended purpose as described in this operation manual.
2. This appliance must be properly installed in accordance with the installation
instructions before it is used. See the installation section for more details.
3. This appliance must be connected to a proper electrical outlet with the correct
electrical supply.
4. Proper grounding must be ensured to reduce the risk of shock and fire. Do not cut or
remove the grounding plug! If you do not have a three-prong electric receptacle outlet
in the wall, have a certified electrician install the proper outlet. The wall receptacle
must be properly grounded.
5. Never unplug your appliance by pulling on the power cord. Always grasp the plug
firmly and pull straight out from the outlet.
6. Immediately replace worn power cords, loose plugs and power outlets.
7. To reduce the risk of electric shock or fire, do not use extension cords or adapters to
connect the unit to an electrical power source.
8. Unplug your appliance before cleaning or making any repairs.
9. We suggest that a certified technician perform the service if for any reason this
product requires service.
10. If your old appliance is being discarded, we recommend that you remove the door and
leave the shelves in place. This will reduce the possibility of danger to children.
11. This appliance should not be recessed or built into an enclosed cabinet. It is designed
for freestanding installation only.
12. Do not operate your appliance in the presence of explosive fumes.
13. Do not tamper with the controls.
14. Do not operate this appliance when parts are missing or broken.
15. Do not use this appliance for commercial use.
16. This appliance is designed for indoor use only and should not be used outdoors.
17. To reduce is the risk of injury, do not allow children to play in or on the appliance.
Close supervision is necessary when the appliance is used near children.
18. The appliance door must be closed during operation. Do not leave the door open
when children are near the dispenser.
19. DO NOT not attempt to operate this unit with a damaged cord or plug.
20. DO NOT roll the KEGORATOR™ with loaded beer kegs on carpet floor.
21. This appliance is not intended for use by young children or infirm persons without
supervision.
22. This appliance is NOT A TOY!
23. Young children should be supervised to ensure that they do not play with this
appliance.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Precautions of CO
(Carbon Dioxide) Gas
2
1. CO gas can be dangerous! CO cylinders contain high-pressure compressed gas,
2
2
which can be hazardous if not handled properly. Make sure you read and understand
all the procedures for the CO cylinders before installation.
2
2. Always connect the CO cylinder to a regulator! Failure to do so may cause an
2
explosion resulting in possible death or injury when the cylinder valve is opened,
3. Never connect the CO cylinder directly to the beer keg.
2
4. Always follow the correct procedures when changing the CO cylinder.
2
5. Never drop or throw a CO cylinder.
2
6. Always keep CO cylinders away from heat. Store extra cylinders in a cool place
2
(preferably 70° F). Secure fasten with a chain in an upright position when storing.
7. Always ventilate and leave the area immediately if CO leakage has occurred!
2
8. There are two safety devices in the pressure system in the form of a valve. One
safety feature is on the CO bottle. The second is on the regulator.
2
9. Never attempt to refill CO cylinder yourself. CO tanks can be refilled at locations
2
2
such as welding supply shops, party stores, or wherever kegs are purchased.
NOTE: If the refrigerator has been placed in a horizontal or tilted position for any period of
time wait 24 hours before plugging the unit in.
DANGER!
Risk of child entrapment! Before throwing away your old
appliance, remove the door so that children may not easily
become trapped inside.
SAVE THESE INSTRUCTIONS
For Future Use
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
•
To ensure that your KEGORATOR™ works to the maximum efficiency it was designed
for, keep it in a location where there is proper air circulation and electrical outlets.
•
•
•
•
•
•
•
Choose a location where the KEGORATOR™ will be away from heat and will not be
exposed to direct sunlight.
This KEGORATOR™ is designed for indoor use only -- it should not be used
outdoors.
This KEGORATOR™ is a freestanding design and should not be placed in a built-in or
recessed area.
Your KEGORATOR™ comes with a 2.5 lb. CO bottle, which should be able to
2
dispense four 15 gallon kegs of beer.
KEGORATOR™ capacity:
4.6 cu. ft.
KEGORATOR™ unit dimensions:
20.3” W x 32.10” H x 26.20” D
The following dimensions are recommended for clearances around the
KEGORATOR™:
Sides …………………… ¾” (19 mm)
Back ……………………. 1” (25 mm)
•
•
KEGORATOR™ unit weight:
77.6 lbs
KEGORATOR™ Specs:
115V 50Hz 1.5A (max amps = 6A)
Use of Extension Cords
•
Avoid using an extension cord because of potential safety hazards in certain
conditions. If it is necessary to use an extension cord, use only a 3-wire extension
cord that has a 3-blade grounding plug. The cord must be equal to or greater than the
electrical rating of the appliance.
Compatible Keg Types
The KEGORATOR™ can hold one Full Size Keg, or one Pony Keg, or Two 5 Gallon Kegs.
24.75”
23”
23”
13.5”
15.5”
8.5”
9”
15.5”
1/4 Barrel Pony Size
5 Gallon Cornelius Keg
5 Gallon D System
1/2 Barrel Full Size
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts & Assembly
Read assembly instructions carefully to ensure that you understand all installation
instructions before installing the KEGORATOR™. If after completing the process you are
still unsure whether the KEGORATOR™ has been properly installed, we recommend that
you contact a qualified installer.
Note: Allow the KEGORATOR™ to stand in an upright position for about 8 hours before
turning on the power. This is very important! Once the unit is laid on it’s side, the Freon in
the refrigeration unit is shifted. The Freon in the refrigeration unit needs to stabilize before
the power is turned on.
Accessories List
CO2 Bottle
Regulator
Hose #1
Connecting Beer Tap to
Regulator & CO Bottle
2
CO Bottle
2
Beer Tap Handle
Large Butterfly
Nut Secures Hose to
Beer Tap
Hose #2
Connects Dispenser
Assembly to Beer Tap
Part Connects to
Keg
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulator
The regulator works the Co2 Tank Valve and measures PSI (pounds per square inch), as
well as the volume of the Co2 gas in the Cylinder.
Output Pressure
Gauge (0-60 PSI)
for measuring PSI
of CO in tank.
2
Screw adjusts the
output pressure
Tank Pressure Gauge
(0-3000 PSI) for measuring
PSI of CO outflow from
2
Tank to Keg.
Pressure Relief Valve
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the CO2 Regulator and the CO2 Cylinder
Follow these steps to safely install the CO regulator and CO cylinder. You must read
2
2
and understand the following procedures for the CO cylinders before installation.
2
NOTE: If all your rubber washers & O-rings are not pre-installed, please refer to your parts
list (pg. 6).
NOTE: Your CO cylinder has DOT (USA Department of Transportation) approval,
2
however the cylinder has been shipped empty to avoid any possible accidents during
transportation. When you purchase the first keg of beer, you must also have your CO
2
cylinder filled at your local supplier. (see page 2, item 9 for suggested locations within your
community)
STEP 1
STEP 2
High pressure washer installed into CO
regulator (may already be installed).
Attach regulator to CO tank connector.
2
2
Some units may
come with this
attachment. It
is not needed
and should be
removed from the
coupler prior to
STEP 3.
STEP 3
The CO rubber
2
directional
washer goes into
the coupler.
STEP 4
STEP 5
Connect the CO
line from the
regulator to the
coupler.
Put one of the
backflow stoppers
in the coupler (the
torpedo goes in
with rounded side
down).
2
OR
OR
There are three different possible
backflow stoppers.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation, contin.
STEP 6
STEP 7
After the backflow stopper has been
inserted, there is a washer that should be
placed on top of the coupler.
After the tap tower has been placed on the
refrigerator and the hose line feeds through
the bottom, attach the wing nut to the
coupler.
Washers
Below are pictures of some of the extra washers that are included with the KEGORATOR™
and where they belong.
O-rings on the CO line
2
O-ring for coupler
O-ring for regulator
CO line to
2
CO line to coupler
2
regulator
Tap tower washer
goes in between
refrigerator and tap
tower.
CO tank band
2
O-ring for tap
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Casters
Follow the steps below to install the casters.
1. Empty the inside of the cabinet completely and lay
the KEGORATOR™ down on it’s side. We
recommend that you place a piece of cardboard or
cloth underneath the cabinet to prevent dents or
scratches.
2. Insert the casters into the holes on the bottom
corners of the cabinet. Tighten each caster
by turning the nut clockwise with a wrench
(not provided in the kit).
3. Once all four casters have been tightened,
stand the cabinet in its upright position.
Note: Two of the casters include locking mechanisms to ensure the unit does not slide on
hard floors. These two locking casters should be fastened at the front end of the unit, with
the unlocked casters fasted on the rear end.
Installing the Beer Tap
Beer
Dispenser
Tower
Follow the steps below to install the beer tap.
24.75"
1. Remove the cabinet plug located
on the work top. Firmly grasp the
cabinet plug, twist and pull upward.
8.5"
Beer Line
Note: Keep this plug in a safe place --
it will be required when using the
High-Pressure Valve
23"
CO Bottle
²
KEGORATOR™ as a refrigerator without
Shut Off Safely
a beer keg in use.
Keg
Coupler
9"
2. There are notches on the
bottom of the draft arm
assembly that line up with
grooves inside the opening
in the top of the KEGORATOR™.
Align the draft arm with the
opening in the top of the unit,
then place inside and twist until
secure. No screws are necessary,
it locks into place simply. The thin
black gasket is not mandatory for
assembly.
13.5"
CO Line
²
15.5"
Single-Gauge
CO Regulator
²
Low Pressure
Valve
23"
Beer Keg
(Not Included)
15.5"
CO Tank
²
Handle
Beer
Dispenser
Tower
Installing the Guardrail
Follow these steps below to install the guardrail.
1.
2.
Place the guardrail on top of the cabinet.
Align all holes of the guardrail with the holes
of the cabinet.
Beer Duct
3.
Secure the guardrail to the cabinet by
placing inside corresponding rubber
holes.
Guard Rail
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Tapping the Beer Keg (Single-Valve Type Barrel)
Follow these steps below to tap the beer keg.
1. Make sure the black pull handle of the coupler is in the closed (up) position before
installing it on the keg (Fig. 1 - below). Insert the keg coupler into the locking neck of
the beer keg and turn clockwise until it locks into position (Fig. 2 - below). This means
that it is secured to the keg.
2. When connecting the beer line to the top of the coupler, it is very important that the
wingnut tightens completely. This must be completed prior to inserting the backflow
stopper into the coupler.
3. Before attaching the CO line, be sure to insert the rubber directional washer into the
2
side of the coupler. Attach the CO line (see step 3 on pg. 5) and hand-tighten firmly.
2
Secure the tank with CO tank strap.
2
Connect to
CO Cylinder
4. Make sure the beer tower faucet is in
the closed (handle pointing straight
back) position before connecting the
coupler to the keg. To secure the tank
connection, pull the coupler handle
out and push down until it locks into
position. Listen for the “click” of the
pull handle when it shifts into the final
downward position (Fig. 4 - below).
2
CO
Gas Line
2
Rubber
Washer
Shut-Off
Valve
CO
Regulator
This will open the beer and CO gas
2
2
CO
2
valves. The keg is now tapped.
5. Carefully tilt the keg and rest the edge
on the keg base board on the bottom
of the interior cabinet. Slide the beer
keg slowly, ensuring that it is properly
located (Fig. 5) and carefully close the
door.
Rubber
Strap
CO
Cylinder
2
Connect to the
Beer Line Tube
Connect to
CO2 Gas
Line Tube
Black pull handle
Keg Coupler
Beer Keg Neck
fig. 1
fig. 2
fig. 3
Lift Upright
Beer Keg
Keg Support
fig. 4
fig. 5
DANGER!
CO can be dangerous! CO cylinders contain
2
2
high-pressured gas, which can be hazardous if handled
improperly.They must be handled with care.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Your KEGORATOR
™
Dispensing Beer
Follow the steps below to dispense beer.
1. Make sure that the KEGORATOR
™
is plugged in properly to a 120V, 60Hz, 15Amps
grounded AC outlet.
2. Place the drip tray under the beer faucet to avoid messes from excess beer.
3. Open the beer faucet by pulling the tap towards you to dispense the beer.
NOTE: If for any reason the beer does not come out of the tap, please refer to theTapping
the Beer Keg section.
4. Increase the pressure if the beer runs too slowly.
5. Hold the glass steady at a 45° angle. When it is 2/3 full, straighten the glass. Proper
foam should be a tight creamy head and the collar on an average glass should be ¾”
to 1” high, ideally.
NOTE: Only open the CO tank 1/4 turn to begin with and then use the regulator to adjust to
2
desired pour. If it is not enough, continue to open the CO tank by 1/4 turn and use regulator
2
until desired setting is reached.
NOTE: It is normal to see condensation form on the faucet. It is caused by the difference in
temperature between the cold beer and the inside of the faucet when beer is flowing through
the line.
Cleaning & Maintenance
Flushing the tubes
Follow the steps below to clean the keg tap and hoses. (see illustration below)
1. Turn off CO completely before attempting to clean.
2
2. Remove the hose from the coupler and carefully twist the dispenser faucet off
the top of the KEGORATOR™.
Detach beer line
1
3. Ensure that the dispenser handle is in the
down position before flushing the hose.
If this is not set correctly, water cannot flow
through. Hold the open end of the hose under
running water for 3-5 minutes, while the
beer dispenser faucet drains into the sink.
This will clear any excess beer that is
trapped inside, helping to prevent any
bacteria or mold that could accumulate inside.
Flush hose with water
2
4. In order to clean and remove any excess beer that
may leak into the unit space inside the door, remove
the black rubber insulation and wipe with a wet towel
as needed.
Storage & Care
Follow the guidelines below to care for your KEGORATOR™ when not in use.
•
Please adjust the temperature control dial to MID or LOW in colder
environments because this unit does not self-defrost and ice may build up inside the
unit. The temperature control dial is located on the back side of the KEGORATOR™
inside the cut out area at the bottom to the lower left.
•
•
Always rinse the beer line if you do not intend to use your KEGORATOR™ for a
period of time. First, turn off the CO and dispense beer until it stops. This will release
2
pressure in the keg so that the coupler can safely be detached.
To avoid permanent damage to the unit, never use sharp objects inside
the KEGORATOR™.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
RETURNS & WARRANTY INFORMATION
SHOULD YOUR UNIT NOT WORK OR IS DAMAGED WHEN YOU FIRST TAKE IT OUT
OF THE BOX PLEASE RETURN IT TO THE PLACE OF PURCHASE IMMEDIATELY.
Should you have any questions, please contact us via email or at the customer service
number listed below between the hours of 8:00 AM and 5:00 PM, Monday through Friday,
Central Standard Time.
Distributed by:
Nostalgia Products Group, LLC
1471 Partnership Dr.
Green Bay, WI 54304-5685
Customer Service
Phone: (920) 347-9122
Customer Service Inquiry
Customer Service Inquiry form and click the Submit button. A representative will
contact you as soon as possible.
KEGORATOR™
KRS-2000 Series
Limited Warranty
This appliance is designed and built to provide many years of satisfactory performance
under normal household use. The distributor pledges to the original owner that should
there be any defects in material or workmanship during the first 90 days of purchase,
we will repair or replace the unit at our option. Our pledge does not apply to damages
caused by shipping, mishandling or unit being dropped. A product deemed defective either
from manufacturing or being mishandled is up to the distributor’s discretion. In order to
obtain service under this warranty, please contact Nostalgia Products Group, LLC at the
telephone number listed above or by filling out the Customer Service Inquiry Form located
This warranty does not apply to re-manufactured merchandise.
Please read these instructions carefully. Failure to comply with these instructions, damages
caused by improper replacement parts, abuse or misuse will void this pledge to you and is
being made in place of all other expressed warranties.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
|