Murray Tiller FT6000X92A User Manual

Front Tine Rototiller

Operator’s Manual

Transport Position

Operating Position

Includes Models

FT6000X92A

F-041303L

Download from Www.Somanuals.com. All Manuals Search And Download.

MODEL INFORMATION

MODEL IDENTIFICATION ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 3 ADJUSTMENTS ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 12

Belt TensionAdjustment ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 12

WARRANTY ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 4

Depth Regulator Lever ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 13

SAFETY RULES ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 5

OPERATION ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 14

Owner's Responsibility ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 5

Pre-Start Inspection ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 14

General ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 5

Start-up ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 14

Preparation ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 5

Shutting Down ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 15

Operation ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 6

Tilling ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 15

Maintenance and Storageꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 6

Safety Decals ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 7

NORMAL CARE ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 16

Schedule ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 16

FEATURES ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 8

Servicing The Rototillerꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 17

UNPACKINGANDASSEMBLYꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 9

STORAGE ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 20

Unpack Tiller ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 9

Prepare For Storage ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 20

Install the Depth Regulator Lever ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 10

Fill Engine Crankcase ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 10

TROUBLESHOOTINGAND REPAIR ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 21

Troubleshooting Guide ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 21

CONTROLS ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 11

Parts Listings ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 22

Drive Safety Control Lever ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 11

Notes ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ 26

MODEL IDENTIFICATION

ROTOTILLER REFERENCE DATA

Model Description/Number

Record your model number, manufacturer number and

serial number in the space provided for easy referenceꢀ

The model and manufacturer numbers can be found on the

unit IꢀDꢀ plate located on the unit’s left engine mountꢀ Refer

to the Engine Owner’s Manual for location of engine serial

numberꢀ

M/N (Manufacturer's Number)

Dealer Name

S/N (Serial Number)

Date Purchased

ENGINE REFERENCE DATA

Engine Make/Model

Engine ID/Serial Number

WARNING

You must read, understand and comply with all

safety and operating instructions in this manual

before attempting to setup and operate your

rototillerꢀ

Failure to comply with all safety and operating

instructions can result in loss of machine control,

serious personal injury to you and/or bystanders,

and risk of equipment and property damageꢀ The

triangle in the text signifies important cautions or

warnings which must be followedꢀ

WARNING

Engine exhaust from this product contains

chemicals known, in certain quantities, to cause

cancer, birth defects, or other reproductive harmꢀ

F041303L

Download from Www.Somanuals.com. All Manuals Search And Download.

WARRANTY

Thank You ꢀ ꢀ ꢀ

for purchasing an Murray front tine rototillerꢀ We guarantee that this front tine rototiller conforms to applicable North

American safety standards, and have worked to ensure that it will meet your exacting standards for usability and

durabilityꢀ With proper care, your rototiller will provide many years of serviceꢀ

Please take time to read this manual carefully to learn how to operate and service your rototiller correctlyꢀ Failure

to do so could result in personal injury or equipment damageꢀ This manual should be considered a permanent part of

your rototillerꢀ Congratulations on your investment in qualityꢀ

MURRAY, INCꢀ Two Year Limited Warranty

TILLERPRODUCT 2YEARWARRANTY

Murray, Incꢀ warrants to the original purchaser that this unit shall be free from defects in material and workmanship

under normal use and service for a period of Two (2) Years from the date of purchase; however, this warranty does

not cover Normal Wear Parts (except as noted below) or engines, accessories, transmissions, and transaxles

supplied through other companies that furnish their own warranties and provide service through their authorized

field service facilitiesꢀ For additional information, see the warranties covering these particular partsꢀ If you are

uncertain whether your unit contains or is equipped with one or more of these parts, consult your dealer prior to

purchaseꢀ Subject to the terms and conditions noted in this Limited Warranty, we shall, at our option, repair or

replace at no cost to the original purchaser any part covered by this Limited Warranty during the applicable

warranty periodꢀ

Normal Wear Parts are defined as belts, tines, pulley adapters, wheels, and pneumatic tiresꢀ These parts are

warranted to be free from defects in material and workmanship as delivered with the productꢀ Any claim for repair

or replacement of Normal Wear Parts must be made within thirty (30) days of the date of purchaseꢀ No claims involving

damage caused from material use, abuse or misuse will be honoredꢀ

This Murray, Incꢀ Two (2) Year Limited Warranty is your exclusive remedy; however, this warranty is void or does

not apply to any unit that has been tampered with, altered, misused, abused or used for rental or other commercial

and/or professional (non–homeowner) usesꢀ Your warranty does not cover minor mechanical adjustments which

are not due to any defect in material or workmanshipꢀ For assistance in making such adjustments, consult your

Instruction Bookꢀ

To make a claim under this Murray, Incꢀ Two (2) Year Limited Warranty, return the unit (or if authorized in advance,

the defective part) along with your proof of purchase to an Authorized Service Center near youꢀ To locate the nearest

Authorized Service Center, call the Central Parts Distributor for your area shown in the list provided with your unit

or check the Yellow Page listings in your local telephone directoryꢀ If you return the entire unit, we will repair the unitꢀ

If we authorize the return of the defective part only, we will either replace or repair the partꢀ In the case of a defect in

a transmission or differential (as distinguished from a transaxle), the entire transmission or differential must be

returned since they do not include user serviceable partsꢀ

This Murray, Incꢀ Two (2) Year Limited Warranty gives you specific legal rights, and you may also have other rights

whichvaryfromstatetostateꢀThisLimitedWarrantyisgiveninlieuofallotherexpressedandimpliedwarranties

including the implied warranty of merchantability and warranty of fitness for a particular purposeꢀ If you need

additional information on this written warranty or assistance in obtaining service, write or call:

MURRAY, INCꢀ

Outdoor Power Equipment

Customer Service Department

PꢀOꢀ Box 268; Brentwood, Tennessee 37024–0268

1–800–251–8007

F041303L

Download from Www.Somanuals.com. All Manuals Search And Download.

SAFETY RULES

• CAREFULLY READ THIS MANUALAND FOLLOW

OWNER'S RESPONSIBILITY

Safe and effective use of the rototiller is the owner's

ALL INSTRUCTIONSꢀ

responsibilityꢀ

• Be familiar with all controls before operating the tillerꢀ

Your tiller is equipped with a safety device that enables

you to stop the tines quickly in an emergencyꢀ Learn

how the drive safety control lever works and how to

control the tiller at all timesꢀ

1ꢀ Read and follow all safety instructionsꢀ

2ꢀ Maintain the tiller according to directions and schedule

includedꢀ

3ꢀ Ensure that anyone who uses the tiller is familiar with

all controls and safety precautionsꢀ

• Never allow children to operate the tillerꢀ Keep small

children away from the area being tilledꢀ Do not allow

adults to operate the tiller without proper instructionꢀ

GENERAL

• Do not operate the tiller under the influence of alchohol

or drugsꢀ

The Safety Alert symbol shown here is used to

alert you to important safety information that must

be read, fully understood, and followed at all times when

handling, transporting, operating, servicing, or storing your

rototiller unitꢀ

PREPARATION

• Dress appropriately when operating the tillerꢀAlways

wear sturdy footwearꢀ Never wear sandals, sneakers,

or open shoes, and never operate the tiller with bare

feetꢀ Do not wear loose clothing that might get caught

in moving partsꢀ

Each safety alert symbol is followed by a "signal word"

that advised you of the relative intensity, or level, of the

hazard the safety alert instructions pertain toꢀ

The following list of signal words is being provided to help

you understand the intensity levels associated with each

signal word used in this manualꢀ

• Carefully inspect the area to be tilled, and remove all

foreign objectsꢀ Do not till above underground water

lines, gas lines, electric cables, or pipesꢀ Do not

operate the tiller in soil with large rocks and foreign

objects which can damage the equipmentꢀ

DANGER

• Disengage drive safety control lever before starting the

engineꢀ

The signal word "DANGER" is used when a serious

injury or fatality will result if the safety instructions

that follow this signal word are not obeyedꢀ

• Handle fuel with care; it is highly flammableꢀ

aꢀ Use an approved fuel containerꢀ

bꢀ Never add fuel to a running engine or hot engineꢀ

WARNING

cꢀ Fill fuel tank outdoors with extreme careꢀ Never fill

fuel tank indoorsꢀ

The signal word "WARNING" is used when a serious

injury or fatality could result if the safety instructions

that follow this signal word are not obeyedꢀ

dꢀ Replace gasoline cap securely and clean up spilled

fuel before restartingꢀ

• Never attempt to make any adjustments while the

engine is runningꢀ

CAUTION

The signal word "CAUTION" is used when personal

injury, or property or equipment damage could

result if the safety instructions that follow this signal

word are not obeyedꢀ

Engine is shipped from factory without oilꢀ You must

add engine oil before starting engineꢀ

Provides helpful information for proper assembly,

operation, or maintenance of your rototillerꢀ

F041303L

Download from Www.Somanuals.com. All Manuals Search And Download.

SAFETY RULES

• Never allow bystanders near the unitꢀ

OPERATION

• Never operate the tiller without guards, covers, and

• Never operate the tiller without good visibility or lightꢀ

hoods in placeꢀ

• Take all possible precautions when leaving the

machine unattendedꢀ Disengage drive control lever,

stop the engine, wait for all moving parts to stop, and

make certain guards and shields are in placeꢀ

• Keep hands, feet, and clothing away from rotating

partsꢀ Keep clear of tiller tines at all timesꢀ

• Tines rotate when tiller is engaged in forward-- in

forward, tines rotate when the drive safety control

lever is pulled downꢀ Releasing the drive safety

control lever to neutral stops the tinesꢀ

• When leaving the operating position for any reason:

- shut off the engineꢀ

- wait for all moving parts to stopꢀ

• Exercise extreme caution when operating on or

crossing gravel drives, walks, or roadsꢀ Stay alert for

hidden hazards or trafficꢀ

MAINTENANCE AND STORAGE

• Keep machine, attachments, and accessories in safe

working conditionꢀ

• After striking a foreign object, stop the engine, remove

the wire from the spark plug and secure, thoroughly

inspect the tiller for any damage, and repair the

damage before restarting and operating the tillerꢀ

• Check shear bolts, engine mounting bolts, and other

bolts at frequent intervals for proper tightness to be

sure the equipment is in safe working conditionꢀ

• If vegetation clogs the tines, STOP THE ENGINE

AND DISCONNECT THE SPARK PLUG WIRE

before removing vegetation by handꢀ

• To prevent accidental starting, always disconnect the

spark plug wire from the spark plug before performing

tiller maintenanceꢀ

• Engine muffler will be hot from operationꢀ Do not

touch it with bare skin or a severe burn may resultꢀ

• Never run the engine indoorsꢀ Exhaust fumes are

deadlyꢀ

• If the unit should start to vibrate abnormally, stop the

engine and check immediately for the causeꢀ Vibration

is generally a warning of troubleꢀ

• Always allow muffler to cool before filling fuel tankꢀ

• Never store equipment with gasoline in the tank inside

a closed building where fumes may reach an open

flame or sparkꢀAllow the engine to cool before storing

in any buildingꢀ

• Do not run the engine indoors; exhaust fumes are

dangerousꢀ

• Do not overload the machine capacity by attempting

to till too deep at too fast a rateꢀ

• Always refer to the operator's guide instructions for

important details if the tiller is to be stored for an

extended periodꢀ

F041303L

Download from Www.Somanuals.com. All Manuals Search And Download.

SAFETY RULES

SAFETY DECALS

This rototiller unit has been designed and manufactured to provide you with the safety and reliability you would expect

from an industry leader in outdoor power equipment manufacturingꢀ

Although reading this manual and the safety instructions it contains will provide you with the necessary basic knowledge

to operated this equipment safely and effectively, we have placed several safety labels on the tiller to remind you of this

important information while you are operating the unitꢀ

These important safety labels are illustrated below, and are shown here to help familiarize you with the location and

content of the safety messages you will see as you perform normal tilling operationsꢀ Please review these labels now,

and if you have any questions regarding their meaning or how to comply with these instructions, reread the complete

safety instruction text on the preceding pages, or contact your local dealerꢀ

Should any of these labels become unreadable because of being worn, faded, or otherwise damaged during the use of

your tiller, please use the part number information provided to order a replacement label from your local authorized dealerꢀ

These labels are easily applied, and will act as a constant visual reminder to you, and others who may use the

equipment, to follow the safety instructions necessary for safe, effective operation of your rototillerꢀ

Part Noꢀ 48x5410

HOOD WARNING

Hood Decal

Part Noꢀ 48x5318

TINES DANGER/OPERATION

Hood Decal

Part Noꢀ 48x5320

CLUTCH ENGAGE

Handlebar Decal

Part Noꢀ 48x5321

WARNING

Pivot Mount Decal

Part Noꢀ 48x5322

WARNING

Belt Cover Decal

F041303L

Download from Www.Somanuals.com. All Manuals Search And Download.

FEATURES

drive safety control lever

forward cable

hand knob

belt guard

3-way adjustable tine widths

The advantage of the MURRAY gear drive rototiller over other front tine tillers, is the exclusive

– 1 –

unfolding and flexible drag barꢀ This gives the Murraygear drive tiller its stability and its

versatilityꢀ For easy transport, fold the wheels under the engineꢀ During operation, the wheels

unfold back and the drag bar folds downꢀ The long length between the tines and the depth

regulator level make this the most comfortable front tine tiller on the marketꢀ

Operating Position

Transport Position

F041303L

Download from Www.Somanuals.com. All Manuals Search And Download.

UNPACKING AND ASSEMBLY

UNPACK TILLER

1ꢀ Open top of carton and remove handlebar assemblyꢀ

The right and left sides of your

CAUTION

rototiller are determined from

the operating position as you

face the direction of forward

travelꢀ

Do not try to lift the rototiller from the cartonꢀ

2ꢀ Cut open end of carton and remove machine:

aꢀ Tines are pre-assembled at 21” widthꢀ Sharp edge

of tine will be away from operator at top or face down

at front of machineꢀ(Figure 2)

bꢀ Outside tines have two positions- wide 21” & narrow

16”ꢀ For narrow width - assemble with short side of

tine holder pipe towards center of machineꢀ For 11”

width, remove outside tine setsꢀ (Figure 1)

cꢀ For wide width - move left tine to right side and right

to left sideꢀ Assemble with long half of tine pipe

towards machineꢀ (Figure 2)

Narrow Tine Width

Figure 1

dꢀ Remove two (2) hand knobs & bolts and slide top

handle of handlebar over lower loopꢀ Put

5/16-18 x 1-3/4” bolts thru both holes from inside

out, and tighten with hand knobsꢀ

eꢀ Check upper and lower jam nuts for tightnessꢀ See

Figure 4, Belt TensionAdjustmentꢀ

fꢀ Add and check engine oilꢀ

Wide Tine Width

Figure 2

beehive spring

1/4” stretch

upper handlebar

lower

handlebar

loop

upper jam nut

lower jam nut

hand knob

tension spring link

forward cable

Figure 4

Figure 3

F041303L

Download from Www.Somanuals.com. All Manuals Search And Download.

UNPACKING AND ASSEMBLY

INSTALL THE DEPTH REGULATOR

LEVER

FILL ENGINE CRANKCASE

1ꢀ Install the depth regulator lever through hole in bracket

from the bottom up with curve to rear of unit and

secure with detent pinꢀ

Engine is shipped from factory without oilꢀ You

must add engine oil before starting engineꢀ

1ꢀ Add oil according to engine manualꢀ Do not overfillꢀ

Use a clean, high quality detergent oilꢀ Container must

be marked AꢀPꢀIꢀ Service SF - SJꢀ Use no special

additives with recommended oilsꢀ Do not mix oil with

gasolineꢀ Oil level must be fullꢀ Check the oil level by

removing the dipstickꢀ Oil level should be at FULL line

on dipstickꢀ

depth

regulator

lever

detent pin

2ꢀ Always check oil level before starting engineꢀ Refer to

engine manual for capacity and type of oil to useꢀ

Figure 5

– 1 –

F041303L

Download from Www.Somanuals.com. All Manuals Search And Download.

CONTROLS

DRIVE SAFETY CONTROL LEVER

CAUTION

Engage tines into forward, releasing returns machine to

neutralꢀ

This information is provided here only to introduce

the controlsꢀ DO NOT START THE ENGINE AT THIS

TIMEꢀ Starting and operating instructions are given

on page 11ꢀ Please read this section and all

operating and safety instructions before starting your

tillerꢀ

Pulling down on drive safety control lever engages the

tinesꢀ Releasing the drive safety control lever disengages

the tines to a neutral positionꢀ

WARNlNG

drive safety control

lever disengaged

Engine should be off before adjusting any

controlsꢀ

CAUTION

• As a safety precaution, the drive safety control

levers will not lock in the forward positionꢀ

• To stop the wheels and tines at any time

release the drive safety control leversꢀ

WARNlNG

Extreme caution should be used when operating

rototiller in the forward directionꢀ

Figure 6

– 1 –

F041303L

Download from Www.Somanuals.com. All Manuals Search And Download.

ADJUSTMENTS

BELT TENSION ADJUSTMENT

beehive spring

1/4” stretch

Proper belt tension is critical to good performanceꢀAfter

half hour of operation, all cables may have to be adjusted

due to initial stretchꢀ Thereafter, check tension after every

2 hours of operationꢀ

To increase belt tension:

upper jam nut

1ꢀ Loosen upper jam nutꢀ Turn nut up cable in 1/8"

incrementsꢀ

2ꢀ Tighten lower jam nutꢀ

3ꢀ Check adjustmentꢀ

lower jam nut

forward cable

tension spring link

This procedure can be repeated until conduit adjustment

bolts have no more adjustment leftꢀ If no more adjustment

can be made, belt may have to be replacedꢀ

Figure 4

F-041303L

Download from Www.Somanuals.com. All Manuals Search And Download.

ADJUSTMENTS

DEPTH REGULATOR LEVER

Tilling depth is controlled by the height of the depth

regulator leverꢀ

depth

regulator

lever

To adjust tilling depth:

1ꢀ Remove detent pinꢀ

detent pin

2ꢀ Raise the depth regulator lever to position tines at

chosen tilling depthꢀ

3ꢀAlign hole in depth regulator lever with hole in depth

regulator bracket and replace detent pinꢀ

Figure 8

CAUTION

Do not adjust tilling depth unless drive safety control

lever is released to the neutral positionꢀ

– 1 –

F-041303L

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATION

PRE-START INSPECTION

1ꢀ Make sure all safety guards are in place and all nuts

and bolts are secureꢀ

Engine is shipped from factory without oilꢀ You

must add engine oil before starting engineꢀ

2ꢀ Check oil level in engine crankcaseꢀ See your engine

manual for procedure and specificationsꢀ

3ꢀ Inspect air cleaner for cleanlinessꢀ See your engine

manual for procedureꢀ

START-UP

The controls required to start and run the rototiller are

located on the engine and are marked "Choke" and

"Throttle"ꢀ

4ꢀ Check the fuel supplyꢀ Fill the fuel tank no closer than

1 inch from top of tank to provide space for expansionꢀ

See your engine manual for fuel recommendationsꢀ

A more detailed description of engine operation and all

related precautions and procedures can be found in the

engine manufacturer's manual that accompanies each

tillerꢀ

5ꢀ Be sure spark plug is tightened securely and spark plug

wire is attachedꢀ

6ꢀ Check depth regulator lever positionꢀ

Cold Starts

1ꢀ Move choke lever to full choke positionꢀ

CAUTION

Please do not start your tiller until you have read

the Manual that came with your engine, and the

sections in this manual titled Controls, Adjustments

and Safetyꢀ If you have read these, follow the steps

below to start your tillerꢀ Always perform this pre-

start checklist before starting the engineꢀ

2ꢀ Move throttle lever to "start"ꢀ

3ꢀ When starting, operator should place free hand where

indicated and start the engine from the operator

positionꢀ

4ꢀ Pull starting rope out slowly one time and allow to

return normallyꢀ

WARNING

5ꢀ Pull starting rope out rapidly, and allow rope to return

normallyꢀ

Gasoline is highly flammable and must be handled

with careꢀ Never fill the tank when the engine is

hot or runningꢀ Always move outdoors to fill the

tankꢀ

6ꢀ When engine starts, gradually move choke lever to

"no choke" position and increase throttle speedꢀ

Restarting A Warm Engine

Restarting an engine that is already warm from previous

running does not normally require use of the chokeꢀ

1ꢀ Move throttle lever to "start" positionꢀ

2ꢀ When starting, operator should place free hand where

indicated and start the engine from the operator

positionꢀ

3ꢀ Pull starting rope out rapidly until engine startsꢀ Allow

rope to return normallyꢀ

4ꢀ Adjust throttle speed to "high" for best tiller actionꢀ

Idle Speed

Use the "low" position on the throttle lever to reduce stress

on the engine when tilling is not being performedꢀ Lowering

the engine speed to "idle" the engine will help extend the

life of the motor, as well as conserve fuel and reduce the

noise level of the equipmentꢀ

Operating Speed

For normal tilling, set the throttle lever to "fast"ꢀ

F041303L

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATION

TILLING

DANGER

1ꢀ Adjust the depth regulator lever to desired tilling depthꢀ

Always keep hands and feet clear of rotating

machine partsꢀ

NOTE: Raise depth regulator lever up one hole at a

time, testing tiller operation after each raiseꢀ Raising

depth regulator lever too high can result in loss of

control of tiller!

WARNING

Temperature of muffler and near by areas may

exceed 150° Fꢀ Avoid these areasꢀ

2ꢀ Move the throttle control to fastꢀ

3ꢀ Place the tiller in forward by pushing down on the

drive control lever--this will engage the tinesꢀ

WARNING

Do not move choke control to CHOKE to stop

engineꢀ Backfire or engine damage may occurꢀ

CAUTION

To stop the tines at any time, release drive safety

control lever to the neutral positionꢀ

SHUTTING DOWN

CAUTION

DANGER

Always release drive safety control lever to the

neutral position before adjusting the depth regulator

leverꢀ

Engine and surrounding parts become extremely

hot during normal use, and will cause serious burn

injuries if touched before the engine has cooledꢀ

Allow engine to cool completely before touching

these hot surfacesꢀ

To stop the engine at any time, move throttle

control to the off positionꢀ To stop tines at any

time, release drive safety control lever to the

neutral positionꢀ

F041303L

Download from Www.Somanuals.com. All Manuals Search And Download.

NORMAL CARE

SCHEDULE

Your rototiller has been designed and produced by the industry's leading manufacturer of outdoor power equipment to

provide you with years of reliable operationꢀ

Keeping your tiller in top running condition will prolong its life, and help you obtain optimum performance whenever you

wish to till your gardenꢀ

Please read this normal care schedule, and observe these recommended care operating intervals to extend the life of

your unitꢀ

50 hrs or

Every Season

Maintenance Operation

Check belt tension

Page

Before Each Use

Change forward belt

belt

Engine maintenance

Check or fill engine oil

Check tiller transmission grease

Clean tine axle shaft

18, EM

Check throttle control adjustment

EM = See engine manual

1 Adjust throttle control after first 3 hours of operation or if engine is hard to start or run-on occursꢀ

2 Change oil after first 5-8 hours of use, then after every 50 hours or every seasonꢀ Change oil every 25 hours

when operating under heavy load or in high temperaturesꢀ

F041303L

Download from Www.Somanuals.com. All Manuals Search And Download.

NORMAL CARE

Belt Replacement

SERVICING THE ROTOTILLER

1ꢀ Turn off engineꢀ Engine must be coolꢀ

General

2ꢀ Remove spark plug wire from spark plug and secureꢀ

The following information will help you make the necessary

checks and perform the procedures required to follow the

normal care recommendations made for your rototiller unitꢀ

3ꢀ Remove belt guardꢀ (Figꢀ 11)

4ꢀ Remove dirt shield from bottom of tillerꢀ (Figꢀ 10)

remove the belt from the engine pulley:

If you prefer, your local authorized service dealer can make

these checks and perform the required procedures for youꢀ

Check Belt Tension

Dirt Shield

Belt tension may decrease over timeꢀ It must be adjusted

within the first half hour of operation, and checked after

every two hours of operationꢀ Proper adjustment will

assure long belt lifeꢀ Too much or too little belt tension will

cause premature belt failureꢀ To check and adjust the

forward belt tension:

1ꢀ Turn off engineꢀ Engine must be coolꢀ

2ꢀ Remove spark plug wire from spark plug and secureꢀ

3ꢀ With drive safety control lever in the neutral position,

measure length of spring when compressedꢀ

4ꢀ Pull down on drive safety control lever and measure

length of spring when stretched outꢀ Ideal length would

be 1/4" longerꢀ

Figure 10

- force the belt down from engine pulley and slowly

rotate pulley by pulling the starter cordꢀ

- remove the belt from transmission pulleyꢀ

- push the belt forward and out front of machineꢀ

install new belt:

- place new belt onto transmission pulleyꢀ

- force belt up onto engine pulley while rotating

pulley with engine starter cordꢀ

5ꢀ Replace belt guard and dirt shieldꢀ

1-1/4"

6ꢀ Attach spark plug wireꢀ

belt guard

removed

Figure 9

WARNING

Check forward belt tension regularlyꢀ Too much

or too little tension will cause premature belt

failureꢀ

take belt out

from front

Figure 11

F041303L

Download from Www.Somanuals.com. All Manuals Search And Download.

NORMAL CARE

CAUTION

Do not operate tiller before reading the engine

manual provided in the parts packetꢀ

Engine is shipped from factory without oilꢀ You

must add engine oil before starting engineꢀ

WARNING

Check or Fill Engine Oil

Temperature of muffler and near by areas may

exceed 150° Fꢀ Avoid these areasꢀ

1ꢀ Add oil according to engine manualꢀ Do not overfillꢀ

Use a clean, high quality detergent oilꢀ Container must

be marked AꢀPꢀIꢀ Service SF - SJꢀ Use no special

additives with recommended oilsꢀ Do not mix oil with

gasolineꢀ Oil level must be fullꢀ Check the oil level by

removing the dipstickꢀ Oil level should be at FULL line

on dipstickꢀ

Engine can overheat and become damaged if debris

blocks the cooling system or rotating screenꢀ

2ꢀ Always check oil level before starting engineꢀ Refer to

engine manual for capacity and type of oil to useꢀ

Change Engine Oil

1ꢀ Remove the fasteners that secure the dirt shield at the

bottom of the tillerꢀ

Never run engine without complete air cleaner

installed on engineꢀ

2ꢀ Take off the dirt shield and you can see the oil drainꢀ

3ꢀ Refer to the engine manual for how to change oilꢀ

Engine Maintenance

Refer to the engine manual included in your parts packet

for information on engine maintenanceꢀ Your engine

manual provides detailed information and a maintenance

schedule for performing the following tasks:

Dirt Shield

1ꢀ Check oil level before each use or after every 8 hours

of operationꢀ

2ꢀ Change oil after first 5-8 hours of operationꢀ Change oil

` while engine is warmꢀ Refill with new oil of recommended

gradeꢀ

4ꢀ Check spark plug yearly or every 100 hours of operationꢀ

5ꢀ Service air cleanerꢀ

6ꢀ Keep engine and parts cleanꢀ

7ꢀ Check engine and equipment often for loose nuts and

bolts, keep these items tightenedꢀ

Figure 12

F041303L

Download from Www.Somanuals.com. All Manuals Search And Download.

NORMAL CARE

Check Tiller Transmission Grease

Clean Tine Axle Shaft

1ꢀ Turn off engineꢀ Engine must be coolꢀ

2ꢀ Remove spark plug wire from spark plug and secureꢀ

3ꢀ Remove all vegetation, string, wire, and other material

that may have accumulated on the axle between the

inside set of tines and the seal on the transmission

housingꢀ

Tiller transmission is shipped from factory with

the proper amount of greaseꢀ

To add grease, remove both high and low grease portsꢀ

Inject grease in bottom until you see some at top hole,

transmission is now fullꢀ

4ꢀ Replace spark plug wireꢀ

grease out,

high grease

port

grease in,

low grease

port

Figure 12

F041303L

Download from Www.Somanuals.com. All Manuals Search And Download.

STORAGE

PREPARE FOR STORAGE

CAUTION

Follow the steps below to prepare your tiller for storageꢀ

Read your engine manual for detailed instructions on

preparing the engine for storageꢀ

Do not store tiller in an non-ventilated area where

fuel fumes may reach flame, sparks, pilot lights or

an ignited objectꢀ Drain fuel outdoors away from

any ignition sourcesꢀ Use only approved fuel

containersꢀ

1ꢀ Protect wheels and axles from rust:

- Coat the axles lightly with axle greaseꢀ

2ꢀ Run with gas stabilizer in fuelꢀ

3ꢀ Drain the fuel tankꢀ Run the engine until it stopsꢀ

4ꢀ While engine is still warm, drain the oil from the

engineꢀ Refill with fresh oil of the recommended gradeꢀ

5ꢀ Remove spark plug, pour one-half ounce of clean

engine oil into cylinderꢀ Pull starter handle slowly

several times to distribute oilꢀ Replace spark plugꢀ

6ꢀ Clean entire tillerꢀ

7ꢀ Store your tiller in a clean, dry buildingꢀ

F041303L

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING AND REPAIR

TROUBLESHOOTING GUIDE

CAUTION

While normal care and routine maintenance will extend

the life of your rototiller, prolonged or constant use may

eventually require that service be performed to allow it to

continue operating properlyꢀ The troubleshooting guide

below lists the most common problems, causes and

remediesꢀ

Practice safety at all timesꢀ Engine must be turned

off and allowed to cool, and spark plug wire must

be disconnected and secured before attempting

any maintenance or repairꢀ

PROBLEM

REMEDY/ACTION

· Connect spark plug wire to spark plug

Engine will not start

· Throttle must be positioned at choke for a cold start

Engine runs rough, floods during operation

Engine is hard to start

· Clean or replace air cleaner

· Drain old fuel and replace with freshꢀ Use gas stabilizer

at end of season

· Make sure spark plug wire is securely attached to spark

plug

· Drive control safety lever must be released to neutral to

start the engine

Engine misses or lacks power

· Clean or replace air cleaner

· Improper carburetor adjustment, take to authorized

engine service center

· Replace spark plug and adjust gap

· Drain and refill gas tank and carburetor

Engine will not stop when throttle control is positioned at

stop

· See engine manual to check and adjust throttle linkage

Tiller moves forward during starting

· Drive safety control lever must be released to neutral to

start the engine

Tiller is difficult to control when tilling (machine jumps or

lurches forward)

· Raise the tines for shallower tilling by raising the depth

regulator lever, see page 10

· Lower engine speed in hard ground

Belts squeal in neutral

· Adjust belt guide:

- turn engine off and allow muffler to cool

- disconnect spark plug wire from spark plug

- remove the dirt shield

- pull down on drive safety control lever

- manually bend belt guide so there is 1/16 inch

or less clearance between belt guide and belt

- replace the dirt shield

- replace spark plug wire

Belts squeal in forward operation

· Turn engine off and allow muffler to cool

· Disconnect spark plug wire from spark plug

· Release drive safety control lever to neutral

· Adjust engage cable

· Replace spark plug wire

F041303L

Download from Www.Somanuals.com. All Manuals Search And Download.

HANDLEBAR ASSEMBLY

FT6000X92A

KEY NOꢀ

PART #

AR3262E701

028X23

DESCRIPTION

FRONT TINE DRIVE LEVER, WELDED

PUSH CAP, 3/8” Diaꢀ

AR3261

15x146

FRONT TINE TENSION SPRING LINK

NUT-Nyloc, #10-24

AR53530

15x147

SPRING-Bee Hive, Forward CableAdjust

NUT-Jam, 5/16"-24

7401038

AR3108A

094068

AR3264E201

315288

TOP HANDLEASSEMBLY

CABLEASSEMBLY WITH FERREL

KNOB - Wing

BOTTOM HANDLE

BOLT 5/16’-18 UNC X 1ꢀ75 CURVED HD

BOLT-Hex Hd, 3/8”-16 x 1ꢀ00”, Grade 5

NUT-Hex, 3/8”-16

01x137

015X84

F-041303L

Download from Www.Somanuals.com. All Manuals Search And Download.

FT6000X92A

SHAFT ASSEMBLY

KEY NOꢀ

PART #

37X138

DESCRIPTION

BELT-Forward

001X64

018X15

17x146

AR746

AR3179

ARM1000

2001022

AR3323E701

001X75

AR3324E701

015X88

AR3326E701

01X199

CAPSCREW-Hex Hd, 5/16-24 x 3/4”

LOCKWASHER-Spring, 5/16”

WASHER, ꢀ34 ID X 1ꢀ2X 11GATHK

SPACER, 11/16” ID x 3/8” THK

TRANSMISSION PULLEY

TRANSMISSIONASSEMBLY

KEY-Square, 3/16” x 3/4”

TINE SET-Outside Right

BOLT-Hex Hd, 5/16-18 x 1-3/4

TINE SET-Inside

NUT-Biway Lock, 5/16-18

TINE SET-Outside Left

BOLT-Hx Hd, 1/4-20 x 7-1/2”

LOCKWASHER - Spring ꢀ25”

NUT - ꢀ25-20 HEX NYLOCK B2

018X32

15X116

F-041303L

Download from Www.Somanuals.com. All Manuals Search And Download.

FT6000X92A

MOTOR MOUNT & HOOD ASSEMBLY

F-041303L

Download from Www.Somanuals.com. All Manuals Search And Download.

MOTOR MOUNT & HOOD ASSEMBLY

FT6000X92A

KEY NOꢀ

PART #

01X175

01X139

01X198

----------

DESCRIPTION

BOLT-Hex Hd, 5/16-18 x 2”

BOLT-Hex Hd, 5/16-18 x 1-1/4”

BOLT-Hex Hd, 5/16-18 x 3-1/4”

ENGINE*

1901051

17X124

018X31

PULLEY-1 -Drive, 7/8” ID

WASHER, ꢀ406 ID x ꢀ812 OD, Engꢀ Pulley

LOCKWASHER-Spring, 3/8”

3/8-24 x 1ꢀ75 BES

01X194

028X22

PUSH NUT, 1/2” Dia

AR1714250

1001701

AR3266E201

AR3157E701

01X100

AR3130AE201

AR744

015X88

WHEEL & TIRE ASSEMBLY

DETENT PIN, 5/16”

DRAG BAR MOUNT

DEPTH REGULATOR LEVER

BOLT-HHCS, 1/4-20 x 1/2”

FRAME-Engine Mount

SPACER

HEX FLG, NUT, 5/16-18

SPRING-IdlerArm

BELTGUIDE & MOUNT

CABLE YOKE

IDLERARM-Forward

SCREW-Sheet Metal, ꢀ25-20Xꢀ59

FRONT BELT COVER

LINK PIN

BOLT-HEX HD, 3/8-16 x ꢀ1ꢀ00”, Grade 5

COTTER PIN

PULLEY-Forward Idler

NUT-Hex flange, 3/8-16

DIRT SHIELD

NUT-Nyloc, 1/4”

SHIELDASSEMBLY

REAR COVER ASSEMBLY

WHEEL SHAFT, 1/2” Hinge

Washer, ꢀ390 ID X ꢀ750OD X 13 GATHK

AR1407

AR3182A Z

AR53596 Z

AR3360 Z

26X263

AR3237E201

29X107

01X137

030X20

50793

015X84

1901049E201

15X116

7401039

7401040

AR3149 Z

017X48

* Parts are available from anAuthorized Service Centerꢀ See “Engines, Gasoline” or “Gasoline Engines” in the

yellow pages of the telephone directoryꢀ

F-041303L

Download from Www.Somanuals.com. All Manuals Search And Download.

______________________________________________________________

Download from Www.Somanuals.com. All Manuals Search And Download.

MURRAY, INCꢀ CENTRALPARTS DISTRIBUTORS

GULF COAST ENGINE, INCꢀ

FRANK EDWARDS COꢀ

3626 Parkway Blvdꢀ

West Valley City, UT 84120

1-800-318-0201

BILLIOU’S, INCꢀ

1343 South Main Stꢀ

Porterville, CAꢀ 93257

(559)784-4102 or 1-877-245-5468

FAX 1-800-266-7337

Arizona, California, Hawaii,

Nevada

4202 Russell Drꢀ

Corpus Christi, TXꢀ 78408

1-800-825-6999

FAX (888)888-7036

Arkansas (counties Hempstead,

Howard, Lafayette, Little River,

Miller, Nevada, Pike, Sevier) New

Mexico, Oklahoma, Texas,

Mexico

FAX (801)736-8067

Colorado, Idaho (counties

Bannock Bearlake, Bingham,

Blaine, Booneville, Butte, Camas,

Caribou, Cassia, Custer, Franklin,

Fremont, Gooding, Jefferson,

Jerome, Lemhi, Lincoln, Madison,

Minidoka, Oneida, Power, Teton,

Twin Falls) Montana (all counties

except Flathead, Lake, Lincoln,

Mineral, Missoulo, Ravalli,

Sanders), Utah, Wyoming

BROWN & WISER, INCꢀ

9991 SꢀWꢀAvery Street

Tualatin, ORꢀ 97062

(503)692-03301-800-882-4782

FAX (503)691-2041

Alaska, Idaho (countiesAda,

Adams, Benewah, Boise, Bonner,

Boundry, Canyon, Clearwater,

Elmore, Gem, Idaho, Kooten,

Latah, Lewis, NEZ Perce, Owyee,

Payette, Ravalli, Shoshone, Valley,

Washington), Montana (counties

Flathead, Lake, Lincoln, Mineral,

Missoulo, Ravalli, Sanders),

Oregon, Washington

WISCONSIN MAGNETO,

INCꢀ

4727 Nꢀ TeutoniaAveꢀ

Milwaukee, WIꢀ 53209

1-800-733-7388

FAX 1-800-733-0127

Illinois (Nꢀ of Hwyꢀ 80), Michigan

(upper Peninsula), Minnesota,

North Dakota, South Dakota,

Wisconsin

GARDNER, INCꢀ

3641 Interchange Road

Columbus, OHꢀ 43204-1499

1-800-848-8946

FAX 1-800-626-4735

Alabama, Arkansas, (except these

counties: Hempstead, Howard,

Lafayette, Little River, Miller,

Nevada, Pike, Sevier),

CPT CANADA POWER

Connecticut, Delaware, District

of Columbia, Florida, Georgia,

Illinois (South of Hwyꢀ 80),

Indiana, Iowa, Kansas, Kentucky,

Louisiana, Maine, Maryland,

Massachusetts, Michigan (except

upper Peninsula), Mississippi,

Missouri, Nebraska, New

Hampshire, New Jersey, New

York, North Carolina, Ohio,

Pennsylvania, Rhode Island,

South Carolina, Tennessee,

Vermont, Virgina, West Virginia

Puerto Rico

TECHNOLOGY LIMITED

Mississauga

161 WatlineAvenue

Mississauga, Ontario L4Z-1P2

(905)890-6900 or 1-800-861-9559

Edmonton

101-10411-178 Street

Edmonton,Alberta T5S 1R5

(780)453-5791or 1-800-861-9559

Ville St-Laurent

234 Migneron Street

Ville St-Laurent, Quebec H4T 1Y7

(514)731-35591-800-861-9559

Canada

Download from Www.Somanuals.com. All Manuals Search And Download.

Multiquip Portable Generator DCA70US13CAN User Manual
Multitech Modem MT1432BA User Manual
Multi Tech Systems Network Card BL Series User Manual
Napoleon Fireplaces Indoor Fireplace Arlington GDS20N User Manual
NETGEAR Network Router Home Router User Manual
NeumannBerlin Electric Pressure Cooker D1761 User Manual
New Holland Compact Loader L150 User Manual
Numark Industries Musical Toy Instrument NV User Manual
Oster Bottle Warmer 146362 User Manual
Panasonic Electric Shaver ER206 User Manual