OPERATION AND PARTS MANUAL
SERIES
MODEL MVC-82VH/VHW
ONE-WAY PLATE COMPACTOR
(HONDA GX160U1SM12 GASOLINE ENGINE)
Revision #1 (04/25/08)
To find the latest revision of this
publication, visit our website at:
THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
MVC-82VH/VHW • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08) — PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
HONDA GX160U1SM12 ENGINE
DRAWINGS
MVC-82VH/VHW PLATE
COMPACTOR
Cylinder Head Assembly.................................. 36-37
Cylinder Barrel Assembly................................. 38-39
Crankcase Cover Assembly ............................. 40-41
Crankshaft Assembly ....................................... 42-43
Piston/Rings Assembly .................................... 44-45
Camshaft Assembly ......................................... 46-47
Recoil Starter Assembly................................... 48-49
Fan Cover Assembly ........................................ 50-51
Carburetor Assembly ....................................... 52-53
Air Cleaner Assembly....................................... 54-55
Muffler Assembly.............................................. 56-57
Fuel Tank Assembly ......................................... 58-59
Cooling Fan & Flywheel Assembly................... 60-61
Ignition Coil Assembly...................................... 62-63
Control Assembly ............................................. 64-65
Labels Assembly .............................................. 66-67
Proposition 65 Warning ........................................... 2
Table of Contents .................................................... 4
Parts Ordering Procedures ..................................... 5
Safety ................................................................... 6-7
Rules and Regulations ....................................... 8-10
Specifications ........................................................ 11
Dimensions ........................................................... 12
General Information .............................................. 13
Components (Compactor)..................................... 14
Components (Engine) ........................................... 15
Inspection......................................................... 16-17
Operation ......................................................... 18-19
Maintenance..................................................... 20-22
Troubleshooting ................................................ 23-24
Explanation Of Code In Remarks Column ............ 26
Suggested Spare Parts ......................................... 27
Terms and Conditions Of Sale — Parts ................ 68
COMPONENT DRAWINGS
Nameplate and Decals..................................... 28-29
Body Assembly ................................................ 30-31
Vibrator Assembly ............................................ 32-33
Water Tank Assembly (MVC-82VHW Only) ..... 34-35
Specification and part number are
subject to change without notice.
PAGE 4 — MVC-82VH/VHW PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS ORDERING PROCEDURES
Ordering parts has never been easier!
Choose from three easy options:
Effective:
January 1st, 2006
Best Deal!
Order via Internet (Dealers Only)
Orderpartson-lineusingMultiquip’sSmartEquipwebsite!
:
If you have an MQ Account, to obtain a
Username and Password, E-mail us at:
■
■
■
View Parts Diagrams
Order Parts
PrintSpecificationInformation
To obtain an MQ Account, contact your
District Sales Manager for more information.
Use the internet and qualify for a 5% Discount
on Standard orders for all orders which include
complete part numbers.*
Gotowww.multiquip.comandclickon
to log in and save!
Order Parts
Note: Discounts Are Subject To Change
Fax your order in and qualify for a 2% Discount
on Standard orders for all orders which include
complete part numbers.*
Order via Fax (Dealers Only)
:
All customers are welcome to order parts via Fax.
Domestic (US) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Note: Discounts Are Subject To Change
Domestic (US) Dealers Call:
1-800-427-1244
Order via Phone:
Non-Dealer Customers:
International Customers should contact
their local Multiquip Representatives for
Parts Ordering information.
Contact your local Multiquip Dealer for
parts or call 800-427-1244 for help in
locating a dealer near you.
When ordering parts, please supply:
❒
❒
❒
❒
❒
❒
Dealer Account Number
❒
Specify Preferred Method of Shipment:
✓
UPS/Fed Ex
✓ DHL
Dealer Name and Address
■
■
Priority One
Ground
✓
Truck
Shipping Address (if different than billing address)
Return Fax Number
Applicable Model Number
■ Next Day
■
Second/ThirdDay
Quantity, Part Number and Description of Each Part
All orders are treated as Standard Orders
andwillshipthesamedayifreceivedprior
to 3PM PST.
WE ACCEPT ALL MAJOR CREDIT CARDS!
MVC-82VH/VHW • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08) — PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
HAZARD SYMBOLS
FORYOUR SAFETY AND SAFETY OF OTHERS!
Potential hazards associated with the operation of this
equipment will be referenced with Hazard Symbols which
appear throughout this manual, and will be referenced in
conjunction with Safety Message Alert Symbols.
Safety precautions should be followed at all
times when operating this equipment. Failure
to read and understand the Safety Messages
and Operating Instructions could result in injury
to yourself and others.
WARNING — Lethal Exhaust Gas Hazards
Engine fuel exhaust gases contain
poisonous carbon monoxide. This gas is
colorless and odorless, and can cause
death if inhaled. NEVER operate this
equipment in a confined area or enclosed
structure that does not provide ample free
flow air.
This manual has been developed to
provide complete instructions for the
safe and efficient operation of this
equipment. Refer to the engine
manufacturer's instructions for data
relative to its safe operation.
Before using this equipment ensure that the operating
individual has read and understood all instructions in this
manual.
WARNING — Explosive Fuel Hazards
Fuel is extremely flammable and its
vapors can cause an explosion if ignited.
DO NOT start the engine near spilled fuel
or combustible fluids.
SAFETY MESSAGE ALERT SYMBOLS
The three Safety Messages shown below will inform you
about potential hazards that could injure you or others. The
Safety Messages specifically address the level of exposure
to the operator, and are preceded by one of three words:
DANGER,WARNING, or CAUTION.
DO NOT fill the fuel tank while the engine
is running or hot. DO NOT overfill tank, since spilled
fuel could ignite if it comes into contact with hot engine
parts or sparks from the ignition system. Store fuel in
approved containers, in well-ventilated areas and away
from sparks and flames.
DANGER
You WILL be KILLED or SERIOUSLY INJURED if you
DO NOT follow these directions.
WARNING — Burn Hazards
Engine components can generate extreme
heat. To prevent burns, DO NOT touch
these areas while the engine is running or
immediately after operation. Never operate
the engine with heat shields or heat guards
removed.
WARNING
You CAN be KILLED or SERIOUSLY INJURED if you
DO NOT follow these directions.
WARNING — Respiratory Hazards
CAUTION
ALWAYS wear approved respiratory
protection when required.
You CAN be INJURED if you DO NOT follow these
directions.
PAGE 6 — MVC-82VH/VHW PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
CAUTION — Rotating Parts Hazards
CAUTION — Overspeed Conditions
NEVER operate equipment with covers or
guards removed. Keep fingers, hands, hair
and clothing away from all moving parts
to prevent injury.
NEVER tamper with the factory setting of
the engine governor. Personal injury and
equipment damage can result if operating
in speed ranges above the maximum
allowable.
CAUTION — Accidental Starting Hazards
CAUTION — Equipment Damage Hazards
ALWAYS place the equipment ON/OFF
switch in the OFF position when the
equipment is not in use.
Other important messages are provided throughout this
manual to help prevent damage to your equipment, other
property, or the surrounding environment.
CAUTION — Eye and Hearing Hazards
ALWAYS wear approved eye and hearing
protection.
MVC-82VH/VHW • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08) — PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES AND REGULATIONS
„
„
NEVER touch the hot exhaust manifold,
muffler or cylinder.Allow these parts to cool
before servicing engine or pump.
WARNING — Read This Manual
Failure to follow instructions in this manual may lead to
serious injury or even DEATH! This equipment is to be
operated by trained and qualified personnel only! This
equipment is for industrial use only.
ALWAYS allow the engine to cool before
adding fuel or performing service and maintenance
functions. Contact with hot components can cause
serious burns.
GENERAL SAFETY
„
NEVER operate this equipment in any enclosed or narrow
area where free flow of the air is restricted. The engine
of this equipment requires an adequate free flow of
cooling air. If the air flow is
restricted it will cause serious
damage to the equipment or
engine and may cause injury
to people and property.
Remember the engine gives
„
„
„
DO NOT operate or service this equipment
before reading this entire manual.
This equipment should not be operated by
persons under 18 years of age.
NEVER operate this equipment without proper protective
clothing, shatterproof glasses, steel-toed boots and other
protective devices required by the job.
off DEADLY gases.
„
„
ALWAYS refuel in a well-
ventilated area, away from sparks and open flames.
„
„
NEVER operate this equipment when not
feeling well due to fatigue, illness or when
under medication.
ALWAYS use extreme caution when working with
flammable liquids.When refueling, stop the engine and
allow it to cool.
NEVER operate this equipment under the
influence of drugs or alcohol.
„
„
DO NOT smoke around or near the
equipment. Fire or explosion could result
from fuel vapors, or if fuel is spilled on a
hot engine.
NEVER operate the equipment in an
explosive atmosphere or near combustible
materials. An explosion or fire could result
causing severe bodily harm or even
death.
„
NEVER disconnect any "emergency or safety
devices".These devices are intended for operator safety.
Disconnection of these devices can cause severe injury,
bodily harm or even death! Disconnection of any of these
devices will void all warranties.
„
„
„
„
„
DO NOT top-off fuel tank.Topping-off is dangerous as it
causes fuel to spill.
„
„
NEVER use accessories or attachments that are not
recommended by Multiquip for this equipment. Damage
to the equipment and/or injury to user may result.
ALWAYS store the equipment in a clean, dry location
out of the reach of children.
NEVER run engine without air cleaner. Severe engine
damage may occur.
Manufacturer does not assume responsibility for any
accident due to equipment modifications. Unauthorized
equipment modification will void all warranties.
NEVER leave the equipment unattended with the engine
running.Turn off engine when unattended.
„
„
Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
CAUTION must always be observed while servicing this
equipment.Rotating parts can cause injury if contacted.
ALWAYS check the equipment for loosened threads or
bolts before starting.
PAGE 8 — MVC-82VH/VHW PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES AND REGULATIONS
LOADING AND UNLOADING
REFUELING
„
Before lifting, make sure that equipment parts (hook and
vibration insulator) are not damaged and screws are not
loosened or lost.
FUEL
„
ALWAYS make sure crane or lifting device has been
properly secured to the lifting bail (hook) of the equipment.
„
„
NEVER lift the equipment while the engine is running.
Use adequate lifting cable (wire or rope) of sufficient
strength.
„
„
Use one point suspension hook and lift straight upwards.
FUEL
NEVER allow any person or animal to stand underneath
the equipment while lifting.
„
Do not to lift machine to unnecessary heights.
TRANSPORTING
MAINTENANCE SAFETY
„
NEVER lubricate components or attempt service on a
running machine.
„
ALWAYS allow the machine a proper amount of time to
cool before servicing.
„
„
Keep the equipment in proper running condition.
Fix damage to the equipment immediately and always
replace broken parts.
„
Dispose of hazardous waste properly. Examples of
potentially hazardous waste are used motor oil, fuel and
fuel filters.
TYPICAL
PLATE COMPACTOR
„
„
ALWAYS shutdown engine before transporting.
„
„
DO NOT use food or plastic containers to dispose of
hazardous waste.
Tighten fuel tank cap securely and close fuel cock to
prevent fuel from spilling.
DO NOT pour waste, oil or fuel directly onto the ground,
down a drain or into any water source.
„
„
Drain fuel when transporting equipment over long
distances or bad roads.
ALWAYS tie down the equipment during transport by
securing the equipment with rope.
MVC-82VH/VHW • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08) — PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES AND REGULATIONS
EMERGENCIES
BATTERY SAFETY (FOR ELECTRIC START)
„
„
„
ALWAYS know the location of the nearest
■
The battery contains acids that can cause
injury to the eyes and skin. ALWAYS wear
safety glasses to avoid eye irritation.
fire extinguisher.
ALWAYS know the location of the nearest
first aid kit.
■
■
■
■
ALWAYS wear well-insulated gloves when
picking up the battery.
In emergencies, always know the location
of the nearest phone or keep a phone on the job site.
Also know the phone numbers of the nearest
ambulance, doctor and fire department. This
information will be invaluable in case of emergency.
ALWAYS keep the battery charged. If the battery is not
charged, a buildup of combustible gas will occur.
DO NOT charge battery if frozen. Battery can explode.
When frozen, warm the battery to at least 61° F (16° C).
ALWAYS make sure battery terminals are properly
connected. Inadequate battery connections may cause
poor starting of the equipment and create other
malfunctions.
■
■
ALWAYS keep battery cables in good working condition.
Repair or replace all worn cables.
ALWAYS recharge the battery in an vented air
environment, to avoid risk of a dangerous concentration
of combustible gases.
■
■
ALWAYS disconnect the negative battery terminal before
performing service on the equipment.
If the battery liquid (dilute sulfuric acid) comes in contact
with clothing or skin, rinse skin or clothing immediately
with plenty of water.
■
If the battery liquid (dilute sulfuric acid) comes in contact
with your EYES, rinse eyes immediately with plenty of
water and contact the nearest doctor or hospital to seek
medical attention.
DANGER — Explosion Hazards
The risk of an explosion exists when performing service
on the battery. To avoid severe injury or DEATH:
DO NOT drop the battery. There is the
possibility of risk that the battery may
explode.
DO NOT expose the battery to open
flames, sparks, cigarettes, etc.The battery
contains combustible gases and liquids. If these gases
and liquids come in contact with a flame or spark, an
explosion could occur.
PAGE 10 — MVC-82VH/VHW PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Table 1. Specifications (Compactor)
MVC-82VH/MVC-82VHW
Models
Handle
HAV (Center Handle)
3080 lbf. (13.7 kN)
Centrifugal Force
Number of Vibrations
Traveling Speed
5,600 vibrations/min (93 Hz)
82 ft./min (25meters/min)
22.4 x 17.7 in. (570 x 450 mm)
38.2 in. (970 mm)
Plate Size (LxW)
Length (Including Handle)
Height (Including Handle)
Height (Without Handle)
38.0 in. (965 mm)
22.4 in. (570 mm)
Operating Weight (VH)
Operating Weight (VHW)
181 lbs. (82 kg.)
198 lbs. (90 kg.)
Water Tank Capacity (VHW Model Only)
Max. Area Of Compaction
11.6 qt. (11.0 liters)
7,262 sq. ft./hr. (675 sq. m/hr)
0.15 qt. (0.14 liters)
Vibrator Oil Capacity
Table 2. Specifications (Engine)
Model
HONDA GX160U1SM12
Air-cooled 4 stroke, Single Cylinder, OHV,
Horizontal Shaft Gasoline Engine
Type
Bore X Stroke
Displacement
2.7 in. x 1.8 in. (68 mm x 45 mm)
163 cc (9.9 cu. in)
Max Output
5.5 H.P./3600 R.P.M.
Engine
Fuel Tank Capacity
Fuel
Approx. 0.95 U.S. gallons (3.6 liters)
Unleaded Automobile Gasoline
0.63 qts (0.60 liters)
Lube Oil Capacity
Speed Control Method
Starting Method
Centrifugal Fly-weight Type
Recoil Start
120 x 14.2 x 13.2 in. (304 x 362 x 335 mm)
23.1 lbs (10.48 Kg.)
Dimension (L x W x H)
Dry Net Weight
MVC-82VH/VHW • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08) — PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
DIMENSIONS
C
B
D
E
A
Table 3. Dimensions
Description
Reference Letter
Dimension
A
B
C
D
E
Length (including handle )
Height (without handle)
Height (including handle)
Plate Length
38.2 inches (970 mm)
22.4 inches (570 mm)
38 inches (965 mm)
22.4 inches (570 mm)
17.7 inches (450 mm)
Plate Width
PAGE 12 — MVC-82VH/VHW PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL INFORMATION
DEFINITION OF PLATE COMPACTOR
FREQUENCY/SPEED
The Mikasa MVC-82VH/VHW is a walk-behind, one-way
plate compactor designed for the compaction of sand,
mixed soils and asphalt.This plate compactor is a powerful
compacting tool capable of applying a tremendous force
in consecutive high frequency vibrations to a soil surface.
Its applications include compacting for road, embankments
and reservoirs as well as backfilling for gas pipelines, water
pipelines and cable installation work.
The compactor's vibrating plate has a frequency range of
5600 vpm (vibrations per minute). The travel speed of the
compactor is approximately 82 ft./minute (25 meters/
minute).
ENGINE
The Mikasa MVC-82VH/VHW Plate Compactor is equipped
with a Honda GX160U1SM12 gasoline engine.
VIBRATORY PLATES
CONTROLS
The vibratory plates of the MVC-80VH/VHW produce low
amplitude high frequency vibrations, designed to compact
granular soils and asphalt.
Before starting the MVC-82VH/VHW Plate Compactor,
identify and understand the function of the controls and
components.
The resulting vibrations cause forward motion.The engine
and handle are vibration isolated from the vibrating plate.
MVC-82VH/VHW • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08) — PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPONENTS (COMPACTOR)
1
10
4
9
3
2
5
WATER TANK
(MVC-82VHW ONLY)
8
7
6
Figure 1. Plate Compactor Controls and Components
Figure 1 shows the location of the basic controls and
components of the MVC-80VH/VHW Plate Compactor.The
function of each control is described below:
6. Belt Cover – Remove this cover to gain access to the
V-belts. NEVER run the compactor without the V-belt
cover. If the V-belt cover is not installed, the possibility
exists that your hand may get caught between the V-
belt and clutch, causing serious injury and bodily harm.
1. Water Tank Cap (VHW Only) – Remove this cap to
add water to the water tank.
7. Vibrating Plate – A flat, open plate made of durable
2. Fuel Tank Cap – Remove this cap to add fuel.
cast iron construction used in the compacting of soil.
3. Lifting Bale –When lifting of the compactor is required
either by forklift, crane, etc., tie rope or chain around
this lifting point.
8. Vibration Case – Encloses the eccentric, gears and
counter weights.
9. Water Shut-Off Valve (VHW only) – Turn this valve
downward to let water flow from the water tank to the
water tube.
4. Handle Bar – When operating the compactor use this
handle bar to maneuver the compactor.
5. Gasoline Engine – This plate compactor uses a
HONDA GX160U1SM12 engine. Refer to the HONDA
owner's manual for engine information and related
topics.
10. WaterTank (VHW only) – Holds 13.8 quarts of water
(removable, no tools required).
PAGE 14 — MVC-82VH/VHW PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPONENTS (ENGINE)
Figure 2. Engine Controls & Components
ENGINE COMPONENTS
6. Choke Lever – Used in the starting of a cold engine,
or in cold weather conditions. The choke enriches the
fuel mixture.
The engine (Figure 2) must be checked for proper
lubrication and filled with fuel prior to operation. Refer to
the manufacturer's engine manual for instructions and
details of operation and servicing.
7. Air Cleaner – Prevents dirt and other debris from
entering the fuel system. Remove wing-nut on top of
air filter cannister to gain access to filter element.
1. Fuel Filler Cap – Remove this cap to add unleaded
gasoline to the fuel tank. Make sure cap is tightened
securely. DO NOT over fill.
8. Spark Plug – Provides spark to the ignition system.
Set spark plug gap to 0.6 - 0.7 mm (0.028 - 0.031
inch). Clean spark plug once a week.
DANGER — Explosive Fuel Hazard
Adding fuel to the tank should be done
only when the engine is stopped and has
had an opportunity to cool down. In the
event of a fuel spill, DO NOT attempt to
start the engine until the fuel residue has
been completely wiped up, and the area surrounding
the engine is dry.
Operating the engine without an air filter,
with a damaged air filter, or a filter in need
of replacement will allow dirt to enter the
engine, causing rapid engine wear.
WARNING — Burn Hazard
2. Throttle Lever – Used to adjust engine RPM speed
(lever advanced forward - SLOW, lever back toward
operator - FAST).
Engine components can generate
extreme heat. To prevent burns, DO
NOT touch these areas while the
engine is running or immediately after
operating. NEVER operate the engine
with the muffler removed.
3. Engine ON/OFF Switch – ON position permits engine
starting, OFF position stops engine operations.
4. Recoil Starter (pull rope) – Manual-starting method.
Pull the starter grip until resistance is felt, then pull
briskly and smoothly.
9. Muffler – Used to reduce noise and emissions.
10. Fuel Tank – Holds unleaded gasoline. For additional
5. Fuel Valve Lever – OPEN to let fuel flow, CLOSE to
information refer to engine owner's manual.
stop the flow of fuel.
MVC-82VH/VHW • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08) — PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
INSPECTION
BEFORE STARTING
The Oil Alert System will automatically
stop the engine before the engine falls
below safe limits.Always be sure to check
the engine oil level prior to starting the
engine.
1. Read safety instructions at the
beginning of manual.
2. Clean the compactor, removing
dirt and dust, particularly the
engine cooling air inlet,
carburetor and air cleaner.
Table 4. Oil Type
3. Check the air filter for dirt and dust. If air filter is dirty,
replace air filter with a new one as required.
Season
Summer
Spring/Fall
Winter
Temperature
25°C or Higher
25°C~10°C
Oil Type
SAE 10W-30
SAE 10W-30/20
SAE 10W-10
4. Check carburetor for external dirt and dust.Clean with
dry compressed air.
5. Check fastening nuts and bolts for tightness.Loosened
screws or bolts due to vibration, could lead to
unexpected accident.
0°C or Lower
ENGINE OIL CHECK
DANGER — Explosive Fuel Hazard
1. To check the engine oil level, place the pump on secure
level ground with the engine stopped.
Adding fuel to the tank should be done
only when the engine is stopped and has
had an opportunity to cool down. In the
event of a fuel spill, DO NOT attempt to
start the engine until the fuel residue has
been completely wiped up, and the area surrounding
the engine is dry.
2. Remove the filler dipstick from the engine oil filler hole
(Figure 3) and wipe clean.
FUEL CHECK
1. Remove the gasoline cap located on top of fuel tank.
Figure 3. Engine Oil Dipstick (Removal)
2. Visually inspect to see if the fuel level is low. If fuel is
low, replenish with unleaded fuel.
3. Insert and remove the dipstick without screwing it into
the filler neck.Check the oil level shown on the dipstick.
3. When refueling, be sure to use a strainer for filtration.
DO NOT top-off fuel. Wipe up any spilled fuel
immediately!
4. If the oil level is low (Figure 4), fill to the edge of the oil
filler hole with the recommended oil type (Table 4).
Maximum oil capacity is 0.63 quarts (0.60 liters).
Figure 4. Engine Oil Dipstick (Oil Level)
PAGE 16 — MVC-82VH/VHW PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
INSPECTION
2. The V-belt tension is proper if the V-belt bends 10 to
15 mm (Figure 7) when depressed with finger midway
between the clutch and vibration pulley shafts.
V-BELT CHECK
CAUTION — V-Belt Check
NEVER attempt to check the V-belt with the engine
running. Severe injury can occur if your hand (Figure 5)
gets caught between the V-belt and the clutch. Always
use safety gloves.
CLUTCH
PULLEY
Figure 7. V-Belt Tension
3. A loose V-belt will decrease the power transmission
output causing reduced compaction and premature
wear of the belt.
VIBRATOR
PULLEY
4. If the V-belt becomes worn or loose, replace it.
Figure 5. V-Belt Hazard
VIBRATOR OIL CHECK
1. Place the plate compactor horizontally on a flat surface.
Make sure the compactor is level when checking the
oil in the vibrator assembly.
1. To check the V-belt tension, remove the three bolts
that secure the belt cover to the frame as shown in
Figure 6.
2. Check vibrator oil level by removing the oil plug
(vibrator oil gauge) as shown in Figure 8. The oil
level should be up to the oil plug. The vibrator holds
140 cc (approximately 0.3 pint). IMPORTANT, if oil is
required, replace using only SAE10W-30 motor oil.
VIBRATOR
OIL PLUG
Figure 8. Vibrator Oil Plug
Figure 6. V-Belt Cover Removal
MVC-82VH/VHW • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08) — PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
The CLOSED position of the choke lever
enriches the fuel mixture for starting a
COLD engine. The OPEN position
provides the correct fuel mixture for
normal operation after starting, and for
restarting a warm engine.
CAUTION — Read Manual
DO NOT attempt to run the compactor
until the Safety and Initial Start-up sections
have been read and understood.
4. Place the throttle lever (Figure 12) halfway between
INITIAL START-UP
fast and slow.
1. Place the fuel valve lever (Figure 9) in the "ON"
position.
Figure 9. Fuel Valve Lever
Figure 12.Throttle Lever
2. Place the Engine ON/OFF switch (Figure 10) in the
5. Grasp the starter grip (Figure 13) and slowly pull it out.
The resistance becomes the hardest at a certain
position, corresponding the compression point.Rewind
the rope a little from that point and pull out sharply.
"ON" position.
CAUTION — Starter Rope
DO NOT pull the starter rope all the way to the end
DO NOT release the starter rope after pulling. Allow it
to rewind as soon as possible.
Figure 10. Engine ON/Off Switch
3. Place the Choke Lever (Figure 11) in the "OPEN"
position.
Nnnn
Figure 13. Starter Grip
Figure 11. Choke Lever
PAGE 18 — MVC-82VH/VHW PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
6. If the engine has started, slowly return the choke lever
(Figure 11) to the CLOSED position. If the engine has
not started, repeat steps 1 through 5.
„
„
Remember the compactor does not work as efficiently
on clay or soils that have a high moisture content level.
If the soil has a high moisture level, dry soil to appropriate
moisture content level or carry out compaction twice.
7. Before the compactor is put into operation, run the
engine for 3-5 minutes.
STOPPING THE ENGINE
8. Check for abnormal engine noises or fuel leaks.
OPERATION
CAUTION — Stopping the Engine
NEVER stop the engine suddenly while working at high
speeds.
CAUTION — Follow Safety Rules
Make sure to follow all safety rules referenced in the
safety section of this manual before operating
compactor. Keep work area clear of debris and other
objects that could cause damage to the compactor or
bodily injury.
Normal Shutdown
1. Place the throttle lever (Figure 12) in slow position,
and listen for the engine speed to decrease.
2. Place the Engine ON/OFF switch (Figure 10) in the
"OFF" position.
1. Once the engine has started, move the engine throttle
lever quickly to the fast position.
3. Place the fuel valve lever (Figure 9) in the "OFF"
position.
2. With the throttle lever in the fast position, the engine
speed should be around 2,300 RPM, therefore
engaging the centrifugal clutch.
Emergency Shutdown
1. Move the throttle lever quickly to the slow position,
and place the Engine ON/OFF switch in the "OFF "
position.
ALWAYS move the throttle lever quickly
without hesitation, because increasing
the engine speed slowly causes the
clutch to slip.
3. Firmly grasp the compactor's handle bar with both
hands, the compactor will begin moving forward.
4. Slowly walk behind the compactor and be on the
lookout for any large objects or foreign matter that
might cause damage to the compactor or bodily injury.
5. Compactor traveling speed may drop on soils which
contain clay, however there may be cases where
traveling speed drops because the compaction plate
does not leave the ground surface easily due to the
composition of the soil. To rectify this problem do the
following:
„
Check the bottom plate to see if clay or equivalent
material has been lodged in the plate mechanism. If so,
wash with water and remove.
MVC-82VH/VHW • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08) — PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
CAUTION — Inspection and Service
CAUTION — Inspection Intervals
Inspection
Inspection and other services should always be carried
These inspection intervals are for operation under
normal conditions. Adjust your inspection intervals
based on the number hours plate compactor is in use,
and particular working conditions.
out on hard and level ground with the engine shutdown.
INSPECTION AND MAINTENANCE
CAUTION — Fuel Piping
To make sure your plate compactor is always in good
working condition before using, carry out the maintenance
inspection in accordance with Tables 5 through 7.
Fuel piping and connections should be replaced every
2 years.
Table 5. Engine Maintenance Schedule
Every
3 months 6 months
or
25 hrs.
Every
Every
year
or
Every
2 years
or
First
Month or
10 hrs.
Description (3)
Operation
Before
or
50 hrs.
100 hrs.
200 hrs.
Check
Change
Check
X
Engine Oil
X
X
X
Air Cleaner
All Nuts & Bolts
Spark Plug
Change
X (1)
Re-tighten If
Necessary
Check-Clean
Replace
Check
X
X
X
Cooling Fins
Spark Arrester
Fuel Tank
Clean
X
X
Clean
Fuel Filter
Check
X
Idle Speed
Check-Adjust
X (2)
Valve
Clearance
X (2)
Check-Adjust
Check
Fuel lines
Every 2 years (replace if necessary) (2)
(1) Service more frequently when used in DUSTY areas.
(2) These items should be serviced by your service dealer, unless you have the proper tools and are mechanically proficient.
Refer to the HONDA Shop Manual for service procedures.
(3) For commercial use, log hours of operation to determine proper maintenance intervals.
PAGE 20 — MVC-82VH/VHW PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
3. Replace engine oil with recommended type oil as listed
in Table 4. For engine oil capacity, see Table 2 (engine
specifications). DO NOT overfill.
Table 6. Machine Inspection
Item
Hours of Operation
4. Reinstall drain bolt with sealing washer and tighten
securely.
(Starting check)
Every 8 hours (every day)
Every 8 hours (every day)
Every 8 hours (every day)
Loose or lost screws
Damage of any part
Function of controlling
system part
Every 8 hours (every day)
Every 100 hours
Vibrator oil check
Vibrator oil
replacement
Every 300 hours
V-belt (clutch) check
Every 200 hour
Figure 14. Engine Oil (Draining)
DAILY SERVICE
AIR FILTER
„
„
„
Check for leakage of fuel or oil.
1. The air filter element should be cleaned because a
clogged air cleaner can cause poor engine starting,
lack of power and shorten engine life substantially.
Check engine oil.
Check for loose screws including tightness. See Table 7
below (tightening torque ) for retightening.
2. To clean or replace air filter loosen the wing nut on the
air filter housing (Figure 15), remove the cover and
take out air filter cartridge. If only cleaning of the air
filter is desired blow through the air filter cartridge from
the inside, moving a jet of dry compressed air up and
down until all dust is removed.
Table 7. Tightening Torque (in. kg/cm) Diameter
Material 6mm 8mm 10mm 12mm 14mm 16mm 18mm 20mm
4T
6-8T
11T
*
70
150
250
400
300
500
800
500
800
750
1,100 1,400 2,000
100
150
1,300 2,000 2,700 3,800
1,200 2,000 2,900 4,200 5,600
100 (6mm) 300 ~ 350 (8mm) 650 ~ 700 (10mm)
* (In case counter-part is of aluminum)
(Threads in use with this machine are all right handed.)
(Material and quality of material is marked on each bolt, and screw).
ENGINE OIL
1. Replace the engine oil in first 20 hours of operation
and every 100 hours afterwards.
2. Drain the engine oil when the oil is warm after
operation. Remove the oil filler cap then unscrew the
engine oil drain plug located at the base of the engine.
Drain the old oil into a pan (Figure 14).
Figure 15. Air Cleaner
MVC-82VH/VHW • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08) — PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
SPARK PLUG
Checking Clutch
1. Remove and clean the spark plug (Figure 16).
Check the clutch simultaneously withV-belt checking. With
belt removed, check outer drum of the clutch for seizure
and "V" groove for wear or damage with your eyes. Clean
the "V" groove as necessary. Wear of lining or shoe should
be checked with running check. If the shoe is worn, power
transmission becomes deficient and slipping will result.
2. Adjust the spark gap to 0.028 ~0.031 inch (0.6~0.7 mm).
This unit has electronic ignition, which requires no
adjustments.
WARNING — V-Belt Hazard
NEVER attempt to check the V-belt with the engine
running. Severe injury can occur if your hand (Figure
5) gets caught between theV-belt and the clutch.Always
use safety gloves.
Figure 16. Spark Plug Gap
CAUTION — Vibration Check
CHANGING VIBRATOR OIL
Whenever the compactor's vibration becomes weak or
lost during normal operation regardless of operation
hours, check the V-belt and clutch immediately.
1. When changing the vibrator oil, remove the drain plug
(Figure 8).
2. Tip the compactor to drain the oil. Note that the oil will
drain more easily while it is hot.
PLATE COMPACTOR STORAGE
3. Remember to use only 10W-30 motor oil when
replacing vibrator oil.
For storage of the plate compactor for over 30 days, the
following is required:
CHECKING/REPLACING THE V-BELT AND CLUTCH
„
Drain the fuel tank completely or add STA-BIL to the
fuel.
After 200 hours of operation, remove the upper belt cover
to check the V-belt tension. Tension is proper if the belt
bends about 10 mm when depressed strongly with finger
between shafts. Loose or worn V-belts reduces power
transmission efficiency, causing weak compaction and
reduces the life of the belt itself.
„
„
Run the engine until the fuel is completely consumed.
Completely drain the oil from the engine crankcase and
follow procedures described in the HONDA engine
Owner's Manual for engine storage.
Replacing the V-belt
„
„
„
Completely drain the compactor's hydraulic oil from the
vibrating case.
Remove the upper and lower belt covers. Engage an offset
wrench (13 mm) or the like to vibrator pulley (lower)
fastening bolt. Engage waste cloth or the like at midway of
V-belt on the left side and while pulling it back strongly,
rotate the offset wrench clockwise so that the V-belt will
come off.
Clean entire plate compactor, especially the bottom plate
removing all dirt and foreign matter.
Cover plate compactor and engine with plastic covering
or equivalent and store in a clean, dry place.
Reinstalling the V-belt
Engage V-belt to lower vibrator pulley and push the V-belt
to left side of upper clutch and, in the same manner as in
removal, rotate offset wrench clockwise so that the V-belt
goes back on.
PAGE 22 — MVC-82VH/VHW PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Practically all breakdowns can be prevented by proper
handling and maintenance inspections, but in the event of
a breakdown, please take remedial action following the
diagnosis based on the following troubleshooting tables.
If the problem cannot be remedied, please leave the unit
as is and consult Multiquip's service department.
Table 8. Engine Troubleshooting
Possible Cause
Spark plug bridging?
Symptom
Solution
Check gap, insulation or replace spark plug.
Clean or replace spark plug.
Carbon deposit on spark plug?
Difficult to start, "fuel is
available but no SPARK at
spark plug".
Short circuit due to deficient spark
plug insulation?
Check spark plug insulation, replace if worn.
Improper spark plug gap?
ON/OFF switch is shorted?
Ignition coil defective?
Set to proper gap.
Check switch wiring, replace switch.
Replace ignition coil.
Difficult to start, "fuel is Improper spark gap, points dirtry?
available, and SPARK is
Set correct spark gap and clean points.
Condenser insulation worn or short
present at the spark plug".
Replace condenser.
circuiting?
Spark plug wire broken or short
circuiting?
Replace defective spark plug wiring.
Flush fuel system, and replace with correct
type of fuel.
Wrong fuel type?
Difficult to start, "fuel is
available, spark is present
and compression is
normal"
Water or dust in fuel system?
Air cleaner dirty?
Flush fuel system.
Clean or replace air cleaner.
Suction/exhaust valve stuck or
protruded?
Re-seat valves.
Piston ring and/or cylinder worn?
Replace piston rings and or piston.
Torque cylinder head bolts and spark plug.
Difficult to start, "fuel is
available, spark is present
and compression is low"
Cylinder head and/or spark plug not
tightened properly?
Head gasket and/or spark plug gasket
damaged?
Replace head and spark plug gaskets.
Fill with correct type of fuel.
Fuel not available in fuel tank?
Fuel cock does not open properly?
Fuel filter clogged?
Apply lubricant to loosen fuel cock lever,
replace if necessary.
No fuel present at
carburetor.
Replace fuel filter.
Fuel tank cap breather hole clogged? Clean or replace fuel tank cap.
Air in fuel line? Bleed fuel line.
MVC-82VH/VHW • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08) — PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Table 8. Engine Troubleshooting (continued)
Symptom
Possible Cause
Air cleaner not clean?
Improper level in carburetor?
Defective Spark plug?
Defective Spark plug?
Solution
Clean or replace air cleaner
"Weak in power"
compression is proper and
does not misfire.
Check float adjustment, re-build carbureator.
Clean or replace spark plug.
Flush fuel system, and replace with correct type
of fuel.
Water in fuel system?
"Weak in power"
compression is proper but
misfires.
Dirty spark plug?
Clean or replace spark plug.
Replace ignition coil.
Ignition coil defective?
Spark plug heat value
improper?
Replace with correct type of spark plug.
Engine overheats.
Correct type of fuel?
Replace with correct type of fuel
Clean cooling fins.
Cooling fins dirty?
Governor adjusted correctly?
Governor spring defective?
Fuel flow restricted?
Adjust governor.
Rotational speed fluctuates.
Recoil starter malfunction.
Replace governor spring.
Check entire fuel system for leaks or clogs.
Recoil mechanism clogged with
dust and dirt?
Clean recoil assembly with soap and water.
Replace spiral spring.
Spiral spring loose?
Table 9. Plate Compactor Troubleshooting
Possible Cause
Symptom
Solution
Engine speed too low?
Clutch slips?
Set engine speed to correct RPM.
Check or replace clutch.
V-belt slips?
Adjust or replace V-belt.
Travel speed too low, and
vibration is weak.
Excessive oil in vibrator?
Malfunction in vibrator housing?
Bearing Failure?
Drain excess oil and fill to proper level.
Check eccentric, gears and counter weights.
Replace bearing.
Insufficient engine output?
Check engine, compression etc.
PAGE 24 — MVC-82VH/VHW PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
MVC-82VH/VHW • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08) — PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLANATION OF CODE IN REMARKS COLUMN
QTY. Column
The following section explains the different symbols and
remarks used in the Parts section of this manual. Use the help
numbers found on the back page of the manual if there are any
questions.
Numbers Used - Item quantity can be indicated by a
number, a blank entry, or A/R.
A/R (As Required) is generally used for hoses or other parts
that are sold in bulk and cut to length.
The contents and part numbers listed in the parts section are
subject to change without notice. Multiquip does not
guarantee the availibility of the parts listed.
A blank entry generally indicates that the item is not sold
separately. Other entries will be clarified in the “Remarks”
Column.
REMARKS Column
Sample Parts List:
Some of the most common notes found in the “Remarks”
Column are listed below.Other additional notes needed to
describe the item can also be shown.
NO. PART NO. PART NAME
QTY. REMARKS
1
2
2
3
4
12345
BOLT ...................... 1 ......INCLUDES ITEMS W/
WASHER, 1/4 IN. .............NOT SOLD SEPARATELY
WASHER, 3/8 IN. ... 1 ......MQ-45T ONLY
HOSE ................... A/R ....MAKE LOCALLY
BEARING ............... 1 ......S/N2345B AND ABOVE
*
*
*
12347
12348
12349
Assembly/Kit - All items on the parts list with the same
unique symbol will be included when this item is purchased.
Indicated by:
“INCLUDES ITEMS W/(unique symbol)”
NO. Column
Unique Symbols - All items with same unique symbol
Serial Number Break - Used to list an effective serial
number range where a particular part is used.
( , #,
+
, %, or >) in the number column belong to the same
*
assembly or kit, which is indicated by a note in the “Remarks”
column.
Indicated by:
“S/N XXXXX AND BELOW”
“S/N XXXX AND ABOVE”
“S/N XXXXTO S/N XXX”
Duplicate Item Numbers - Duplicate numbers indicate
multiple part numbers are in effect for the same general
item, such as different size saw blade guards in use or a
part that has been updated on newer versions of the same
machine.
Specific Model Number Use - Indicates that the part is
used only with the specific model number or model number
variant listed. It can also be used to show a part is NOT
used on a specific model or model number variant.
When ordering a part that has more than one
item number listed, check the remarks column for
help in determining the proper part to order.
Indicated by:
“XXXXX ONLY”
“NOT USED ON XXXX”
“Make/Obtain Locally” - Indicates that the part can be
purchased at any hardware shop or made out of available
items. Examples include battery cables, shims, and certain
washers and nuts.
PART NO. Column
Numbers Used - Part numbers can be indicated by a
number, a blank entry, orTBD.
“Not Sold Separately” - Indicates that an item cannot be
purchased as a separate item and is either part of an
assembly/kit that can be purchased, or is not available for
sale through Multiquip.
TBD (To Be Determined) is generally used to show a part
that has not been assigned a formal part number at time of
publication.
A blank entry generally indicates that the item is not sold
separately or is not sold by Multiquip. Other entries will be
clarified in the “Remarks” Column.
PAGE 26 — MVC-82VH/VHW PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
SUGGESTED SPARE PARTS
MVC-80VH/VHWCOMPACTOR WITH
HONDA GX160U1SM12 ENGINE
1TO 5 UNITS
Qty.
P/N
Description
3 ......... 070100312 ............V-BELT
4 ......... 939010254 ............SHOCK ABSORBER
3 ......... 9807956846 ..........SPARK PLUG
1 ......... 28462ZH8003 ....... ROPE, RECOIL STARTER
3 ......... 17210ZE1517 ....... ELEMENT, AIR CLEANER
1 ......... 17620Z4H000 ....... CAP, FUEL TANK
1 ......... 17672ZE2W01 ...... FUEL FILTER, FUEL TANK
MVC-82VH/VHW • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08) — PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
NAMEPLATE AND DECALS
1
”
•
2
˜
5
–
3
—
4
RPF-3310
NPA-759
š
7
™
6
›
8
œ
H
/
8
o
%
nda
8
G
*
X
*
1
1
6
0
&
0
#
U1
:
)
SM12
9
CAUTIO N !
READ OWNERS SERVICE MANUALBEFORE OPERATING OR
SERVICING THIS MACHINE.
ALWAYS KEEP UNAUTHORIZED, INEXPERIENCED,
UNTRAINED PEOPLE AWAY FROMTHIS MACHINE.
MAKE SURE ALLSAFETY DEVICES ARE OPERATIONAL
BEFORE THIS MACHINE IS STARTED. BE SURE ENGINE
IS TURNED OFF AND SPARK PLUGS ARE DISCONNECTED
BEFORE SERVICING THE MACHINE OR COMING IN
CONTACT WITHANY MOVING PART. IF EQUIPMENT IS
POWERED BY AN ELECTRIC MOTOR, DISCONNECT
ELECTRICALPLUG.
NEVER LEAVE MACHINE UNATTENDED WHEN OPERATING.
ALWAYS STOP ENGINE ANDALLOW ENGINE TO COOL
BEFORE ADDING FUELOR OIL.
NPA-329
PAGE 28 — MVC-82VH/VHW PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
NAMEPLATE AND DECALS
NO.
1
2
3
4
5
6
7
8
PART NO.
PART NAME
QTY.
REMARKS
PLATE, SERIAL NO. .............................. 1 .......... CONTACT MQ PARTS DEPT.
DECAL, CAUTION (ICON)..................... 1 .......... NPA-989
DECAL, FUEL CAUTION ....................... 1 .......... NPA-1232
DECAL, V-BELT (RPF-3310) ................. 1 .......... NPA-759
DECAL, CAUTION ................................. 1 .......... NPA-306
920209890
920212320
920207590
920203060
920201580
920101410
920105070
920203290
DECAL, MQ MARK 71X55
DECAL, MIKASA MARK 120X60
DECAL, MIKASA MARK 125MM
1
1
1
9
DECAL, CAUTION ................................. 1 .......... NPA-329
MVC-82VH/VHW • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08) — PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
BODY ASSY.
29
•
œ
60
™
“
™
˜
65
62
™
•
11
”
”
•
27
š
™
–
63
™
65
˜
”
—
”
14-1
¥
B
”
1—
4-• 2
™
—
64
”
— –
14-3
31
–
”
™
61
”
32
–
•
–
33
–
40
—
“
23
–
•
21
”
•
¤
A
41-2
”
—
•
—
”
”
–
›
38
41-1
26-3
•
™
–
–
œ
39
26-2
™
•
•
26-1
™
•
”
32
–
•
–
31
”
•
›
–
28-3
•
17
”
š
1
”
6
™
›
•
•
›
”
28-1
28-2
—
•
42
•
˜
25
47-2
—
š
•
–
36
™
¥
—
45
˜
–
37
š
—
™
46
—
š
47-1
”
6
™
5
˜
—
4
13
”
–
–
3
7
š
”
1
6
™
˜
5
PAGE 30 — MVC-82VH/VHW PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
BODY ASSY.
NO.
1
3
4
5
6
7
11
13
14-1
14-2
14-3
16
17
21
PART NO.
419119550
939010254
959404350
020310080
030210250
031110160
912216004
413436870
001220840
030208200
031108160
031108160
022710809
952400130
070100312
418216470
001221035
030210250
031110160
418216480
001221053
030210250
031110160
418343420
020308060
030208200
031108160
419217800
418457750
408421270
413332920
0053005201
001220820
030208200
939010290
404433430
952403450
001221020
030210250
419910010
419219560
419217810
416459320
416459340
009120407
PART NAME
QTY.
1
4
1
8
8
4
1
1
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
4
4
2
1
1
1
1
1
1
1
2
2
2
2
2
REMARKS
VIB. PLATE 570X450
SHOCK ABSORBER D45H41
EARTH WIRE
NUT M10
WASHER, LOCK M10
WASHER, FLAT M10
ENGINE ASSY, GX160U1SM12
ENGINE NUT, REAR
BOLT 8X40 T
WASHER, LOCK M8
WASHER, FLAT M8
WASHER, FLAT M8
NYLON NUT M8
WASHER 9304
VBELT RPF3310
BELT COVER
BOLT 10X35 T
WASHER, LOCK M10
WASHER, FLAT M10
BELT COVER (IN)
BOLT 10X65 T
WASHER, LOCK M10
WASHER, FLAT M10
COVER SEAL (E/G)
NUT M8
23
25
26-1
26-2
26-3
27
28-1
28-2
28-3
29
31
32
33
36
37
38
39
40
41-1
41-2
42
45
46
WASHER, LOCK M8
WASHER, FLAT M8
BASE
BOLT, ENGINE
CLUTCH SPACER 20.2X25X9.4
CLUTCH ASSY S20A1-124
KEY
BOLT 8X20 T
WASHER, LOCK M8
RUBBER, HANDLE
RUBBER 20X32X28.5/52H
WASHER 11X35X4.5
BOLT 10X20 T
WASHER, LOCK M10
VAS HANDLE ASSY .............................. 1 .......... INCLUDES ITEMS W/ #
VAS HANDLE BODY
GRIP, VAS HANDLE
HANDLE NUT, VAS HANDLE
RUBBER, VAS HANDLE
SUNK HEAD BOLT 10X20 T
47-1
47-2
60
61#
62#
63#
64#
65#
1
1
2
2
2
MVC-82VH/VHW • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08) — PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
VIBRATOR ASSY.
69-1
67
68
62
69-2
72
63
64
61
71
78
79
74
72
68
65
69-1
77-2
69-2
66
70
73
77-1
75
PAGE 32 — MVC-82VH/VHW PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
VIBRATOR ASSY.
NO.
61
62
63
64
65
66
67
68
69-1
69-2
70
71
72
73
74
75
PART NO.
418117730
001221445
030214350
031114260
418456950
060403020
418456960
418456970
001220820
030208200
418460130
418343630
040406307
418456981
951401920
952403450
001221030
030210250
953400270
953405260
PART NAME
VIBRATING CASE
BOLT 14X45 T
WASHER, LOCK M14
WASHER, FLAT M14
CASE COVER/PULLEY
OIL SEAL TC-30458
CASE COVER/SHUT OFF
PACKING
QTY.
1
4
4
4
1
1
1
2
8
8
1
1
2
1
1
1
REMARKS
BOLT 8X20 T
WASHER, LOCK M8
COVER SEAL, VIBRATOR
ECC. ROTOR SHAFT
BEARING 6307C4
PULLEY/VIB.
KEY 7X7X30
WASHER 11X35X4.5
BOLT 10X30 T
77-1
77-2
78
1
1
1
1
WASHER, LOCK M10
PLUG 1/4X14 10L
PACKING 1/4 (CU)
79
MVC-82VH/VHW • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08) — PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
WATER TANK ASSY. (MVC82VHW ONLY)
103
104
102
101
108
106
111
105
107
115
91
109
110
116
112
113
92
114
92
PAGE 34 — MVC-82VH/VHW PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
WATER TANK ASSY. (MVC82VHW ONLY)
NO.
91
92
PART NO.
418118581
002211025
418910080
PART NAME
GUARD HOOK
BOLT 10X25 H, SW
QTY.
1
3
REMARKS
101
WATER TANK W/CAP (ORANGE) ......... 1 .......... INCLUDES ITEMS W/ #
102# 954300342
103# 001241030
104# 033910010
105# 022910180
CAP, WATER TANK (NBR)
BOLT 10X30 U
WASHER 10.5X21X2 SUS
NYLON NUT M10 (SUS)
COCK PT1/4, BH-1211(AL)
NUT PS-1/4
PACKING 11.5X19.5X2
PIPE HOLDER
SPRINKLING PIPE
FLANGE BOLT 8X25 (SUS)
WASHER, FLAT M8 (SUS)
NUT M8 (SUS)
1
1
2
1
1
1
1
1
1
1
2
1
1
1
2
106
107
108
109
110
111
112
113
114
115
116
954403241
959403790
418458320
418345150
418345160
001740825
033910110
020308064
418459330
416453780
418457890
RUBBER CAP
PACKING 8X19X2T
RUBBER (SPRINKLINK)
MVC-82VH/VHW • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08) — PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160U1SM12 ENGINE — CYLINDER HEAD ASSY.
5
11
15
11
14
7
6
14
9
12
14
4
12
1
2
14
8
10
10
3
9
9
PAGE 36 — MVC-82VH/VHW PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160U1SM12 ENGINE — CYLINDER HEAD ASSY.
NO.
1%
2%
3
4%#
5
6
7
8
9
10
11
12
14
15
PART NO.
PART NAME
QTY.
REMARKS
12204ZE1306 GUIDE, IN. VALVE (OS), OPTIONAL
1
12205ZE1315 GUIDE, EX. VALVE (OS), OPTIONAL ... 1 .......... INCLUDES ITEMS W/ #
12210ZH8405 HEAD COMP., CYLINDER..................... 1 .......... INCLUDES ITEMS W/ %
12216ZE5300 CLIP, VALVE GUIDE
12251ZH1800 GASKET, CYLINDER HEAD
12310ZE1020 COVER, HEAD
12391ZE1000 GASKET, CYLINDER HEAD COVER
15721ZH8000 TUBE, BREATHER
90013883000 BOLT, FLANGE (6 X 12)
90043ZE1020 BOLT, STUD (6 X 112)
90047ZE1000 BOLT, STUD (8 X 32)
1
1
1
1
1
4
2
2
2
4
1
9430110160
957230806000 BOLT, FLANGE (8 X 55)
9807956846 SPARK PLUG BPR6ES (NGK)
PIN A, DOWELL (10 X 16)
MVC-82VH/VHW • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08) — PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160U1SM12 ENGINE — CYLINDER BARREL ASSY.
15
3
2
16
19
17
7
19
10
12
17
18
1
13
9
8
11
11
14
13
9
PAGE 38 — MVC-82VH/VHW PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160U1SM12 ENGINE — CYLINDER BARREL ASSY.
NO.
1
2
3
7
8
9
10
11
12
13$
14$
15
16
17
18
19
PART NO.
PART NAME
QTY.
REMARKS
12000ZH8426 CYLINDER BARREL ASSY. .................. 1 .......... INCLUDES ITEMS W/ $
15510ZE1033 SWITCH ASSY., OIL LEVEL
16510ZE1000 GOVERNOR ASSY.
16531ZE1000 SLIDER, GOVERNOR
16541ZE1000 SHAFT, GOVERNOR ARM
90131ZE1000 BOLT, DRAIN PLUG
90451ZE1000 WASHER, THRUST (6MM)
90601ZE1000 WASHER, DRAIN PLUG (10.2MM)
90602ZE1000 CLIP, GOVERNOR HOLDER
91001ZF1003 BEARING, RADIAL BALL (6205)
91201Z0T801 OIL SEAL (25 X 41 X 6)
91353671004 O-RING (14 MM)
9405010000
9410106800
9425108000
1
1
1
1
2
1
2
1
1
1
1
1
2
1
2
NUT, FLANGE (10MM)
WASHER, PLAIN (6MM)
PIN, LOCK (8MM)
957010601200 BOLT, FLANGE (6 X 12)
MVC-82VH/VHW • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08) — PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160U1SM12 ENGINE — CRANKCASE COVER ASSY.
PAGE 40 — MVC-82VH/VHW PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160U1SM12 ENGINE — CRANKCASE COVER ASSY.
NO.
1
3
4
5
PART NO.
PART NAME
QTY.
REMARKS
11300ZE1642 COVER ASSY., CRANKCASE ............... 1 .......... INCLUDES ITEMS W/
*
11381ZH8801 GASKET, CRANKCASE
15600ZE1003 CAP ASSY., OIL FILLER (GRAY) .......... 1 .......... INCLUDES ITEMS W/ #
15600ZG4003 CAP ASSY., OIL FILLER ....................... 1 .......... INCLUDES ITEMS W/ +
1
9#
10+
15625ZE1003 GASKET, OIL FILLER CAP
15625ZE1003 GASKET, OIL FILLER CAP
91201Z0T801 OIL SEAL (25 X 41 X 6)
1
1
1
2
6
1
11
12
13
*
9430108140
PIN A, DOWEL (8 X 14)
957010803200 BOLT, FLANGE (8 X 32)
961006205000 BEARING, RADIAL BALL (6205)
14
*
MVC-82VH/VHW • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08) — PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160U1SM12 ENGINE — CRANKSHAFT ASSY.
PAGE 42 — MVC-82VH/VHW PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160U1SM12 ENGINE — CRANKSHAFT ASSY.
NO.
1
PART NO.
PART NAME
QTY.
1
REMARKS
13310ZE1000 CRANKSHAFT
MVC-82VH/VHW • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08) — PAGE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160U1SM12 ENGINE — PISTON/RINGS ASSY.
PAGE 44 — MVC-82VH/VHW PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160U1SM12 ENGINE — PISTON/RINGS ASSY.
NO.
1
1
1
1
2
2
2
2
PART NO.
PART NAME
QTY.
REMARKS
13010ZL0003 RING SET, PISTON (STD)
13011ZL0003 RING SET, PISTON (OS 0.25)
13012ZL0003 RING SET, PISTON (OS 0.50)
13013ZL0003 RING SET, PISTON (OS 0.75)
13101ZH8010 PISTON (STD)
1
1
1
1
1
1
1
1
1
13102ZH8010 PISTON (OS 0.25)
13103ZH8010 PISTON (OS 0.50)
13104ZH8010 PISTON (0.75)
3
13111ZE1000 PIN, PISTON
4
5
*
6
13200ZE1010 ROD ASSY., CONNECTING .................. 1 .......... INCLUDES ITEMS W/
*
90001ZE1000 BOLT, CONNECTING ROD
90551ZE1000 CLIP, PISTON PIN (18MM)
2
2
MVC-82VH/VHW • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08) — PAGE 45
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160U1SM12 ENGINE — CAMSHAFT ASSY.
PAGE 46 — MVC-82VH/VHW PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160U1SM12 ENGINE — CAMSHAFT ASSY.
NO.
1
2
PART NO.
PART NAME
QTY.
REMARKS
12209ZH8003 SEAL, VALVE STEM
1
14100ZE1812 CAMSHAFT ASSY. ................................ 1 .......... INCLUDES ITEMS W/
*
4
6
7
8
14410ZE1010 ROD, PUSH
14431ZE1000 ARM, VALVE ROCKER
14441ZE1010 LIFTER, VALVE
14451ZE1013 PIVOT, ROCKER ARM
14568ZE1000 SPRING, WEIGHT RETURN
14711ZF1000 VALVE, INLET
14721ZF0000 VALVE, EXHAUST
14751ZF1000 SPRING VALVE
14771ZE1000 RETAINER, IN. VALVE SPRING
14773ZE1000 RETAINER, EX. VALVE SPRING
14781ZE1000 ROTATOR, VALVE
14791ZE1010 PLATE, PUSH ROD GUIDE
90012ZE0010 BOLT, PIVOT (8MM)
90206ZE1000 NUT, PIVOT ADJ.
2
2
2
2
1
1
1
2
1
1
1
1
2
2
9
10
*
11
12
13
14
15
16
17
18
MVC-82VH/VHW • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08) — PAGE 47
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160U1SM12 ENGINE — RECOIL STARTER ASSY.
12
7
5
4
8
14
6 10
11
5
1
13
9
2
15
PAGE 48 — MVC-82VH/VHW PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160U1SM12 ENGINE — RECOIL STARTER ASSY.
NO.
1
PART NO.
PART NAME
QTY.
REMARKS
28400ZH8023ZB STARTER ASSY., RECOIL.............. 1 .......... INCLUDES ITEMS W/
*
2
28410ZH8003ZB CASE, RECOIL STARTER
1
1
2
1
1
1
1
2
1
1
1
1
1
*
4
28421ZH8801
28422ZH8801
28431ZH8801
28433ZH8801
28441ZH8801
28442ZH8003
28443ZH8001
28461ZH8003
28462ZH8003
90003ZH8801
90008ZE2003
90008ZE2003
REEL, RECOIL STARTER
RATCHET, STARTER
PLATE, FRICTION
*
5
*
6
*
7
GUIDE, RATCHET
*
8
9
SPRING, FRICTION
SPRING, RECOIL STARTER
SPRING, RETURN
KNOB, RECOIL STARTER
ROPE, RECOIL STARTER
CLIP, CORD
*
*
10
*
11
*
12
*
13
14
15
BOLT, FLANGE (6 X 10)
BOLT, FLANGE (6 X 10)
*
MVC-82VH/VHW • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08) — PAGE 49
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160U1SM12 ENGINE — FAN COVER ASSY.
14
6
25
2
22
16
21
17
10
20
20
20
PAGE 50 — MVC-82VH/VHW PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160U1SM12 ENGINE — FAN COVER ASSY.
NO.
2
6
PART NO.
PART NAME
QTY.
REMARKS
19610ZE1000ZC COVER, FAN (BLACK)
1
1
1
1
1
1
6
1
1
1
19611ZH8810
19630ZH8000
34150ZH7003
36101ZE1010
36100ZF6P81
90013883000
90022888010
90601ZH7013
957010600800
PLATE, SIDE (OIL ALERT)
SHROUD
ALERT UNIT, OIL
CORD, STOP SWITCH (370MM)
SWITCH ASSY., ENGINE STOP
BOLT, FLANGE (6 X 12)
BOLT, FLANGE (6 X 20)
CLIP, HARNESS
10
14
16
17
20
21
22
25
BOLT, FLANGE (6 X 8)
MVC-82VH/VHW • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08) — PAGE 51
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160U1SM12 ENGINE — CARBURETOR ASSY.
15
31
38
2
26
14
27
25
20
34
28
11
13
29
9
17
6
12
37
3
16
10
4
2
5
2
2
8
7
PAGE 52 — MVC-82VH/VHW PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160U1SM12 ENGINE — CARBURETOR ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
2
16010ZE1812 GASKET SET
16011ZE0005 VALVE SET, FLOAT
16013ZE0005 FLOAT SET
1
1
1
*
3
*
4
*
5
16015ZE0831 CHAMBER SET, FLOAT ........................ 1 .......... INCLUDES O-RING
16016ZH7W01 SCREW SET
16024ZE1811 SCREW SET, DRAIN ............................. 1 .......... INCLUDES GASKET
16028ZE0005 SCREW SET B ...................................... 1 .......... INCLUDES GASKET
16044ZE0005 CHOKE SET
16100ZH8W51 CARBURETOR ASSY. (BE65B B) ......... 1 .......... INCLUDES ITEMS W/
16124ZE0005 SCREW, THROTTLE STOP
16166ZH8W50 NOZZLE, MAIN
16173001004 O-RING
16211ZE1000 INSULATOR, CARBURETOR
16212ZH8800 GASKET, INSULATOR
16220ZE1020 SPACER, CARBURETOR
16221ZH8801 GASKET, CARBURETOR
*
6
1
*
7
*
8
*
9
1
*
10
*
11
*
1
1
1
1
1
1
1
12
*
13
14
*
15
16
17
20
16610ZE1000 LEVER, CHOKE (STD) .......................... 1 .......... INCLUDES ITEMS W/ #
25
16953ZE1812 LEVER, VALVE
1
1
1
1
1
2
1
1
*
26
*
16954ZE1812 PLATE, LEVER SETTING
16956ZE1811 SPRING, VALVE LEVER
16957ZE1812 GASKET, VALVE
16967ZE0811 CUP, FUEL STRAINER
93500030061H SCREW, PAN (3 X 6)
27
*
28
29
*
*
31
*
34#
9430520122
PIN, SPRING (2 X 12)
37
99101ZH80700 JET, MAIN (#70)
99204ZE00350 JET, SET, PILOT (#35) ........................... 1 .......... INCLUDES GASKET
*
38
*
MVC-82VH/VHW • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08) — PAGE 53
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160U1SM12 ENGINE — AIR CLEANER ASSY.
10
1
4
12
2
8
10
5
3
9
7
6
7
11
11
PAGE 54 — MVC-82VH/VHW PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160U1SM12 ENGINE — AIR CLEANER ASSY.
NO.
1
2
PART NO.
PART NAME
QTY.
REMARKS
16271ZE1000 GASKET, ELBOW
1
17210ZE1517 ELEMENT, AIR CLEANER .................... 1 .......... INCLUDES ITEMS W/
*
3
*
4
17218ZE1507 FILTER (OUTER)
1
1
1
1
2
1
17230ZE1820 COVER, AIR CLEANER
17232891000 GROMMET, AIR CLEANER
17235ZE1831 NOISE, MUFFLER
17238ZE7010 COLLAR, AIR CLEANER
17239ZE1000 COLLAR B, AIR CLEANER
5
*
6
7#
8#
9
17410ZE1020 ELBOW, AIR CLEANER ........................ 1 .......... INCLUDES ITEMS W/ #
10
11
12
90325044000 WINGNUT, TOOL BOX SETTING
9405006000 NUT, CAP (6 MM)
957010602000 BOLT, FLANGE (6 X 20)
1
2
1
MVC-82VH/VHW • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08) — PAGE 55
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160U1SM12 ENGINE — MUFFLER ASSY.
19
19
22
2
4
15
7
6
16
19
16
19
23
5
27
9
23
17
23
PAGE 56 — MVC-82VH/VHW PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160U1SM12 ENGINE — MUFFLER ASSY.
NO.
2
4
5
6
7
9
15
16
17
19
22
23
PART NO.
PART NAME
QTY.
REMARKS
18310ZH8810 MUFFLER
1
1
1
1
1
1
1
2
2
4
1
4
18320ZF1H01 PROTECTOR, MUFFLER
18325ZE1010 PROTECTOR, LOWER
18340ZE1010 DEFLECTOR CP
18355ZE1000 ARRESTER, SPARK
18381ZH8800 GASKET, MUFFLER
18522ZE1000 GUIDE, MUFFLER
90002ZG0003 SCREW, TAPPING (4 X 8)
94001080000S NUT, HEX (8MM)
90050ZE1000 SCREW, TAPPING (5 X 8)
90055ZE1000 SCREW, TAPPING (4 X 6)
90055ZE1000 SCREW, TAPPING (4 X 6)
MVC-82VH/VHW • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08) — PAGE 57
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160U1SM12 ENGINE — FUEL TANK ASSY.
12
13
14
11
18
20
17
24
21
27
28
28
7
3
PAGE 58 — MVC-82VH/VHW PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160U1SM12 ENGINE — FUEL TANK ASSY.
NO.
3
7
11
12
PART NO.
PART NAME
RUBBER, SUPPORTER (107MM)
JOINT, FUEL TANK
TANK, FUEL (BLACK)
CAP, FUEL FILLER ......................... 1 .......... INCLUDES ITEMS W/
GASKET, FUEL FILLER CAP
FILTER, FUEL
BOLT, FLANGE (6 X 29)
WASHER (6.5 X 25 X 1.5)
O-RING (5.5 X 1.4)
QTY.
REMARKS
16854ZH8000
16955ZE1000
17510ZE1020ZF
17620Z4H000
17631Z0T812
17672ZE2W01
90004ZH7003
90404680000
91319ME5003
91353671004
9405006000
1
1
1
*
13
14
1
1
1
2
2
1
2
1
1
2
*
17
18
20
21
24
27
27
28
O-RING (14 MM)
NUT, FLANGE (6MM)
FUEL TUBE (4.5 X 140)
BULK HOSE, FUEL (4.5 X 1M)
CLIP, TUBE
950014514040
950014500160M
9500202080
MVC-82VH/VHW • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08) — PAGE 59
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDAGX160U1SM12ENGINE—COOLINGFAN&FLYWHEELASSY.
PAGE 60 — MVC-82VH/VHW PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDAGX160U1SM12ENGINE—COOLINGFAN&FLYWHEELASSY.
NO.
1
2
5
6
PART NO.
PART NAME
QTY.
REMARKS
13331357000 KEY, SPECIAL WOODRUFF (25X18)
19511ZE1000 FAN, COOLING
1
1
1
1
1
28451ZH8001 PULLEY, STARTER
31100ZE1010 FLYWHEEL
90201878003 NUT, SPECIAL (14MM)
10
MVC-82VH/VHW • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08) — PAGE 61
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160U1SM12 ENGINE — IGNITION COIL ASSY.
PAGE 62 — MVC-82VH/VHW PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160U1SM12 ENGINE — IGNITION COIL ASSY.
NO.
1
2
7
11
PART NO.
30500ZE1063 COIL ASSY., IGNITION
30700ZE1013 CAP ASSY.
36101ZE1010 WIRE, STOP SWITCH (370MM)
90121952000 BOLT, FLANGE (6 X 25)
PART NAME
QTY.
REMARKS
1
1
1
2
MVC-82VH/VHW • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08) — PAGE 63
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160U1SM12 ENGINE — CONTROL ASSY.
28
5
21
7
25
18
24
3
8
23
12
26
13
17
11
25
18
24
6
10
14
20
27
20
15
16
PAGE 64 — MVC-82VH/VHW PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160U1SM12 ENGINE — CONTROL ASSY.
NO.
3
5
6
7
PART NO.
PART NAME
QTY.
REMARKS
16500ZH8U43 CONTROL ASSY. .................................. 1 .......... INCLUDES ITEMS W/
*
16551ZE0010 ARM, GOVERNOR
16555ZE1000 ROD, GOVERNOR
16561ZE1020 SPRING, GOVERNOR
16562ZE1020 SPRING, THROTTLE RETURN
16571ZH8020 LEVER CONTROL
16574ZE1000 SPRING LEVER
16575ZH8000 WASHER, CONTROL LEVER
16576891000 HOLDER, CABLE
16578ZE1000 SPACER, CONTROL LEVER
16580ZH8813 BASE CONTROL
16584883300 SPRING, CONTROL ADJUSTING
16592ZE1810 SPRING, CABLE RETURN
16594883010 HOLDER, WIRE
90013883000 BOLT, FLANGE (6 X 12)
90015ZE5010 BOLT, GOVERNOR ARM
90114SA0000 NUT, SELF-LOCK (6MM)
90605230000 CIRCLIP
93500040060H SCREW, PAN (4 X 6)
93500050160A SCREW, PAN (5 X 16)
93500050250H SCREW, PAN (5 X 25)
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
2
2
1
1
1
8
10
*
11
*
12
*
13
*
14
*
15
*
16
*
17
*
18
*
20
21
23
*
24
*
25
*
26
*
27
*
28
9405006000
NUT, FLANGE (6MM)
MVC-82VH/VHW • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08) — PAGE 65
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160U1SM12 ENGINE — LABELS ASSY.
2
6
7
4
PAGE 66 — MVC-82VH/VHW PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160U1SM12 ENGINE — LABELS ASSY.
NO.
2
4
6
7
PART NO.
PART NAME
QTY.
REMARKS
87516ZH7000 MARK, OPERATOR CAUTION
87521ZH8030 EMBLEM (5.5)
1
1
1
1
87528ZH7000 MARK, CHOKE (GRAY)
87532ZH7000 MARK, THROTTLE INDICATION
MVC-82VH/VHW • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08) — PAGE 67
Download from Www.Somanuals.com. All Manuals Search And Download.
TERMS AND CONDITIONS OF SALE — PARTS
PAYMENT TERMS
5. Partsmustbeinnewandresalablecon- Multiquipreservestherighttoquoteandsell
dition,intheoriginalMultiquippackage(if directtoGovernmentagencies,andtoOriginal
Terms of payment for parts are net 30 days.
any), and with Multiquip part numbers Equipment Manufacturer accounts who use
FREIGHTPOLICY
clearlymarked.
our products as integral parts of their own
products.
All parts orders will be shipped collect or
prepaidwiththechargesaddedtotheinvoice.
All shipments are F.O.B. point of origin.
Multiquip’sresponsibilityceaseswhenasigned
manifesthasbeenobtainedfromthecarrier,
andanyclaimforshortageordamagemustbe
settledbetweentheconsigneeandthecarrier.
6. Thefollowingitemsarenotreturnable:
SPECIALEXPEDITINGSERVICE
a. Obsolete parts. (If an item is in the
price book and shows as being re- A$35.00surchargewillbeaddedtotheinvoice
placedbyanotheritem,itisobsolete.) forspecialhandlingincludingbusshipments,
insuredparcelpostorincaseswhereMultiquip
mustpersonallydeliverthepartstothecarrier.
(such as gaskets, seals, “O” rings,
b. Any parts with a limited shelf life
andotherrubberparts)thatwerepur- LIMITATIONSOFSELLER’SLIABILITY
MINIMUMORDER
chasedmorethansixmonthspriorto
thereturndate.
Multiquip shall not be liable hereunder for
damagesinexcessofthepurchasepriceofthe
TheminimumchargeforordersfromMultiquip
is $15.00 net. Customers will be asked for
instructionsregardinghandlingofordersnot
meetingthisrequirement.
c. Anylineitemwithanextendeddealer item with respect to which damages are
netpriceoflessthan$5.00.
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
otherspecial,consequentialorincidentaldam-
ages.
d. Special order items.
RETURNEDGOODSPOLICY
e. Electricalcomponents.
f. Paint,chemicals,andlubricants.
g. Decalsandpaperproducts.
h. Itemspurchasedinkits.
Returnshipmentswillbeacceptedandcredit
willbeallowed,subjecttothefollowingprovi-
sions:
LIMITATIONOFWARRANTIES
Nowarranties,expressorimplied,aremade
in connection with the sale of parts or trade
accessoriesnorastoanyenginenotmanufac-
tured by Multiquip. Such warranties made in
connectionwiththesaleofnew,completeunits
are made exclusively by a statement of war-
rantypackagedwithsuchunits,andMultiquip
neitherassumesnorauthorizesanypersonto
assume for it any other obligation or liability
whatever in connection with the sale of its
products.Apartfromsuchwrittenstatementof
warranty, there are no warranties, express,
impliedorstatutory,whichextendbeyondthe
descriptionoftheproductsonthefacehereof.
1. AReturnedMaterialAuthorizationmust
be approved by Multiquip prior to ship-
ment.
7. Thesenderwillbenotifiedofanymaterial
receivedthatisnotacceptable.
2. ToobtainaReturnMaterialAuthorization,
alistmustbeprovidedtoMultiquipParts
Salesthatdefinesitemnumbers,quanti-
ties, and descriptions of the items to be
returned.
8. Suchmaterialwillbeheldforfiveworking
days from notification, pending instruc-
tions.Ifareplyisnotreceivedwithinfive
days,thematerialwillbereturnedtothe
senderathisexpense.
a. Thepartsnumbersanddescriptions
must match the current parts price
list.
9. Creditonreturnedpartswillbeissuedat
dealer net price at time of the original
purchase,lessa15%restockingcharge.
b. The list must be typed or computer
generated.
10. In cases where an item is accepted, for
which the original purchase document
can not be determined, the price will be
basedonthelistpricethatwaseffective
twelvemonthspriortotheRMAdate.
c. The list must state the reason(s) for
thereturn.
Effective: February 22, 2006
d. The list must reference the sales
order(s)orinvoice(s)underwhichthe
itemswereoriginallypurchased.
11. Credit issued will be applied to future
purchasesonly.
e. The list must include the name and
phonenumberofthepersonrequest-
ingtheRMA.
PRICINGANDREBATES
Prices are subject to change without prior
notice.Pricechangesareeffectiveonaspe-
cificdateandallordersreceivedonorafterthat
datewillbebilledattherevisedprice.Rebates
3. AcopyoftheReturnMaterialAuthoriza-
tionmustaccompanythereturnshipment.
4. Freight is at the sender’s expense. All forpricedeclinesandaddedchargesforprice
partsmustbereturnedfreightprepaidto increaseswillnotbemadeforstockonhand
Multiquip’sdesignatedreceivingpoint.
atthetimeofanypricechange.
PAGE 68 — MVC-82VH/VHW PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
MVC-82VH/VHW • OPERATION AND PARTS MANUAL — REV. #1 (04/25/08) — PAGE 69
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND PARTS MANUAL
HERE’S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
UNITED STATES
Multiquip Corporate Office
18910 Wilmington Ave.
Carson, CA 90746
MQ Parts Department
800-427-1244
310-537-3700
Tel. (800) 421-1244
Fax (800) 537-3927
Fax: 800-672-7877
Fax: 310-637-3284
Contact: [email protected]
Mayco Parts
800-306-2926
310-537-3700
Warranty Department
800-421-1244, Ext. 279 Fax: 310-537-1173
310-537-3700, Ext. 279
Fax: 800-672-7877
Fax: 310-637-3284
Service Department
800-421-1244
Technical Assistance
800-478-1244
Fax: 310-537-4259
Fax: 310-631-5032
310-537-3700
MEXICO
MQ Cipsa
Carr. Fed. Mexico-Puebla KM 126.5
Momoxpan, Cholula, Puebla 72760 Mexico Fax: (52) 222-285-0420
Contact: [email protected]
UNITED KINGDOM
Multiquip (UK) Limited Head Office
Hanover Mill, Fitzroy Street,
Ashton-under-Lyne,
Tel: (52) 222-225-9900
Tel: 0161 339 2223
Fax: 0161 339 3226
Lancashire OL7 0TL
Contact: [email protected]
CANADA
Multiquip
4110 Industriel Boul.
Tel: (450) 625-2244
Fax: (450) 625-8664
Laval, Quebec, Canada H7L 6V3
Contact: [email protected]
© COPYRIGHT 2008, MULTIQUIP INC.
Multiquip Inc, the MQ logo and the Mikasa logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other
trademarks are the property of their respective owners and used with permission.
This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data contained in
this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications, design or the information
published in this publication at any time without notice and without incurring any obligations.
Your Local Dealer is:
Download from Www.Somanuals.com. All Manuals Search And Download.
|