OPERATION & PARTS MANUAL
SERIES
MODEL MVC-90L
ONE-WAY PLATE COMPACTOR
(ROBIN GASOLINE ENGINE)
Revision #1 (11/01/05)
THIS MANUAL MUST ACCOMPANY
THE EQUIPMENT AT ALLTIMES.
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
MULTIQUIP MVC-90L
PLATE COMPACTOR
COMPONENT DRAWINGS
Name Plate and Decals ..................................... 28-29
Body Assy. .......................................................... 30-33
Vibrator Assembly .............................................. 34-35
Clutch Assembly (Old Type) ............................... 36-37
Clutch Assembly (New Type) ............................. 38-39
Proposition 65 Warning ..............................................2
Table Of Contents ......................................................3
Parts Ordering Procedures ........................................4
Specifications .............................................................5
Dimensions ................................................................6
Safety Message Alert Symbols .............................. 7-8
Rules For Safe Operation.....................................9-10
Operation and Safety Decals .................................. 11
General Information ................................................ 12
Components (Plate Compactor) ............................. 13
Components (Robin EH172YD4230 Engine) ......... 14
Inspection................................................................ 15
Start-Up Procedure................................................. 16
Shut-Down Procedure............................................. 17
Operation ................................................................ 18
Maintenance ...................................................... 19-21
Preparation For Long Term Storage ....................... 22
Troubleshooting (Engine)................................... 23-24
Troubleshooting (Plate Compactor) ........................ 25
Explanation Of Codes In Remarks Column ............ 26
Suggested Spare Parts ........................................... 27
ROBIN EH172YD4230 ENGINE
Crankcase Group Assembly ..............................40-41
Crankshaft Assembly .........................................42-43
Intake and Exhaust Group Assembly ................44-45
Governor Assembly ...........................................46-47
Cooling and Starting Group Assembly ..............48-49
Fuel Group Assembly ........................................50-51
Carburetor Assembly .........................................52-53
Electric Device Group Assembly (Recoil Start)..54-55
Oil Sensor Assembly ..........................................56-57
Terms and Conditions Of Sale — Parts .................. 58
Specifications and part numbers
are subject to change without
notice.
MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05) — PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Effective:June 1st, 2005
PARTS ORDERING PROCEDURES
Ordering parts has never been easier!
Choose from three easy options:
Best Deal!
Order via Internet (Dealers Only)
Orderpartson-lineusingMultiquip’sSmartEquipwebsite!
:
If you have an MQ Account, to obtain a
Username and Password, E-mail us at:
■
■
■
View Parts Diagrams
Order Parts
PrintSpecificationInformation
To obtain an MQ Account, contact your
District Sales Manager for more information.
Use the internet and qualify for a 5% Discount
on Standard orders for all orders which include
complete part numbers.*
Gotowww.multiquip.comandclickon
to log in and save!
Order Parts
Note: Discounts Are Subject To Change
Fax your order in and qualify for a 3% Discount
on Standard orders for all orders which include
complete part numbers.*
Order via Fax (Dealers Only)
:
All customers are welcome to order parts via Fax.
Domestic (US) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Note: Discounts Are Subject To Change
Domestic (US) Dealers Call:
1-800-427-1244
Order via Phone:
Non-Dealer Customers:
International Customers should contact
their local Multiquip Representatives for
Parts Ordering information.
Contact your local Multiquip Dealer for
parts or call 800-427-1244 for help in
locating a dealer near you.
When ordering parts, please supply:
❒
❒
❒
❒
❒
❒
Dealer Account Number
❒
Specify Preferred Method of Shipment:
✓
Fed Ex/UPS
✓ DHL
Dealer Name and Address
■
■
Priority One
Ground
✓
Truck
Shipping Address (if different than billing address)
Returln Fax Number
■ Next Day
Applicable Model Number
■
Second/ThirdDay
Quantity, Part Number and Description of Each Part
Unless otherwise indicated by customer, all orders are treated asStandard Orders and will ship
within24hours.WewillmakeeveryefforttoshipAirShipmentsthesamedaytheorderisreceived,
if received prior to 2PM PST. Stock Orders must be noted on fax or web order form.
NOTE
WE ACCEPT ALL MAJOR CREDIT CARDS!
PAGE 4 — MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-90L PLATE COMPACTOR — SPECIFICATIONS
TABLE 1. COMPACTOR SPECIFICATIONS
MVC-90L
Model
Centrifugal Force
Vibration Frequency
Maximum Forward Speed
Plate Size (L x W)
Operating Weight
Maximum Area of Compaction
HP Rating
3,350 lbs. (1,520 kg)
5,800 vpm
82 ft/min (25 m/min)
22 x 19.6 in (560 x 500 mm)
197 lbs. (89 kg)
8,036 sq. ft/hr (746 sq. m/hr)
6.0 BHP (4.6 KW)
Water Tank Capacity
5.6 qts. (5.3 liters)
Table 2. ENGINE SPECIFICATIONS
Model
ROBIN EH172YD4230
Air-cooled 4-cycle, Single
Cylinder, Horizontal Shaft,
Overhead Valve, Gasoline
Engine
Type
Displacement
Max Output
172 cc (10.5 cu-in)
6.0 H.P. (4.5 KW)/4,000
R.P.M.
Engine
4.0 H.P.(3.0 KW)/3,600
R.P.M.
Continuous Output
Fuel Tank Capacity
Approx. .95 U.S. gallons
(3.6 liters)
Unleaded Automobile
Gasoline
Fuel
Lube Oil Capacity
.69 qts. (0.65 liters)
12.64 x 13.98 x 14.96 in.
(321 x 355 x 380 mm)
Dimension
(L x W x H)
Dry
Net Weight
34.1 lbs. (15.5 Kg.)
MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05) — PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-90L PLATE COMPACTOR — DIMENSIONS
Figure 1. MVC-90L Plate Compactor Dimensions
TABLE 3. DIMENSIONS
Reference Letter
Description
Dimensions in. (mm)
34 in. (863.6 mm.)
21 in. (533 mm.)
23 in. (584 mm.)
48 in. (1,219 mm.)
31 in. (787 mm.)
A
Height (Handle Deployed)
Overal Width
B
C
D
E
Length (Plate only)
Length (Handle Deployed)
Height (Handle Detatched)
PAGE 6 — MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-90L PLATE COMPACTOR — SAFETY MESSAGE ALERT SYMBOLS
Potential hazards associated with the operation of an MVC-
90L Plate Compactor will be referenced with Hazard
Symbols which appear throughout this manual, and will be
referenced in conjunction with Safety Message Alert
FORYOUR SAFETY ANDTHE SAFETY OF OTHERS!
Safety precautions should be followed
at all times when operating this
equipment. Failure to read and
understand the Safety Messages and
Symbols.
HAZARD SYMBOLS
WARNING - Lethan Exhaust Gasses
Operating Instructions could result in
injury to yourself and others.
This Owner's Manual has been
developed to provide complete
instructions for the safe and
efficient operation of the
Multiquip MVC-90L Plate
Compactor . Refer to the engine
Engine exhaust gases contain
poisonous carbon monoxide. This gas
is colorless and odorless, and can
cause death if inhaled. NEVER operate
this equipment in a confined area or
enclosed structure that does not provide
ample free flow air.
manufacturer's instructions for data relative to its safe
operation.
Before using this plate compactor, ensure that the
operating individual has read and understands all
instructions in this manual.
WARNING - Explosive Fuel
Gasoline is extremely flammable, and its
vapors can cause an explosion if ignited.
DO NOT start the engine near spilled fuel
or combustible fluids.
SAFETY MESSAGE ALERT SYMBOLS
DO NOT fill the fuel tank while the engine is running or
hot. DO NOT overfill tank, since spilled fuel could ignite if
it comes into contact with hot engine parts or sparks from
the ignition system. Store fuel in approved containers, in
well-ventilated areas and away from sparks and flames.
The three (3) Safety Messages shown below will inform you
about potential hazards that could injure you or others. The
Safety Messages specifically address the level of exposure
to the operator, and are preceded by one of three words:
DANGER, WARNING, or CAUTION.
DANGER
WARNING - Burn Hazards
Engine components can generate extreme
heat. To prevent burns, DO NOT touch
these areas while the engine is running or
immediately after operations. Never
operate the engine with heat shields or heat
guards removed.
You WILL be KILLED or SERIOUSLY injured if you DO
NOT follow directions.
WARNING
You CAN be KILLED or SERIOUSLY injured if you DO
NOT follow directions.
CAUTION - Respiratory Hazard
CAUTION
ALWAYS wear approved respiratory
protection when required.
You CAN be INJURED if you DO NOT follow directions.
MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05) — PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-90L PLATE COMPACTOR — SAFETY MESSAGE ALERT SYMBOLS
CAUTION - Rotating Parts
CAUTION - Equipment Damage Messages
NEVER operate equipment with covers,
or guards removed. Keep fingers, hands,
hair and clothing away from all moving
parts to prevent injury.
Other important messages are provided throughout this
manual to help prevent damage to your light tower, other
property, or the surrounding environment.
CAUTION - Accidental Starting
ALWAYS place the power source, circuit
breakers or ON/OFF switch in the OFF
position, when the generator is not in use,
unless connected to transfer switch.
This reversible plate compactor,
other property, or the surrounding
environment could be damaged
if you do not follow instructions.
CAUTION - Sight and Hearing Hazards
ALWAYS wear approved eye and
hearing protection.
l
PAGE 8 — MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-90L PLATE COMPACTOR — RULES FOR SAFE OPERATION
■
NEVER touch the hot exhaust manifold,
muffler or cylinder. Allow these parts to
cool before servicing engine or generator.
WARNING - ReadThis Manual
Failure to follow instructions in this manual may lead to
Serious Injury or even Death. This equipment is to be
operated by trained and qualified personnel only! This
equipment is for industrial use only.
■
HighTemperatures – Allow the engine
to cool before adding fuel or performing
service and maintenance functions.
Contact with hot components can cause
serious burns.
The following safety guidelines should always be used
when operating the Mikasa MVC-90L Plate Compactor:
■
The engine of this reversible plate compactor requires an
adequate free flow of cooling air. NEVER operate the
reversible plate compactor in any enclosed or narrow area
where free flow of the air is
Safety:
■
■
■
DO NOT operate or service this equipment
before reading this entire manual.
restricted. If the air flow is restricted
it will cause serious damage to
the reversible plate compactor or
engine and may cause injury to
This equipment should not be operated
by persons under 18 years of age.
NEVER operate this equipment without
proper protective clothing, shatterproof glasses, steel-toed
boots and other protective devices required by the job.
people and property.Remember
the vibration roller's engine gives
off DEADLY gases.
■
■
ALWAYS refuel in a well-ventilated area, away from sparks
and open flames.
ALWAYS use extreme caution when working with flammable
liquids. When refueling, stop the engine
and allow it to cool.DO NOT smoke around
or near the machine. Fire or explosion could
result from fuel vapors, or if fuel is spilled on
a hot engine.
■
■
NEVER operate this equipment when not
feeling well due to fatigue, illness or taking
medicine.
NEVER operate the saw under the influence or drugs or
alcohol.
■
NEVER operate the reversible plate compactor in an
explosive atmosphere or near combustible materials. An
explosion or fire could result causing severe bodily harm or
even death.
■
■
Topping-off to filler port is dangerous, as it tends to spill fuel.
ALWAYS store the reversible plate compactor in a clean, dry
location out of the reach of children.
■
■
■
NEVER use accessories or attachments, which are not
recommended by Multiquip for this equipment. Damage to
the equipment and/or injury to user may result.
■
■
■
NEVER run engine without air cleaner. Severe engine
damage may occur.
Manufacturer does not assume responsibility for any accident
due to equipment modifications. Unauthorized equipment
modification will void all warranties.
NEVER leave the reversible plate compactor unattended,
turn off engine.
Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
CAUTION must always be observed while servicing this
reversible plate compactor.Rotating parts can cause injury if
contacted.
■
■
ALWAYS check all the bolts on the light tower for tightness.
■
DO NOT leave reversible plate compactor with engine
running.
NEVER disconnect any "emergency or safety devices".
These devices are intended for operator safety. Disconnection
of these devices can cause severe injury, bodily harm or
even death! Disconnection of any of these devices will void
all warranties.
MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05) — PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-90L PLATE COMPACTOR — RULES FOR SAFE OPERATION
Loading and Unloading (Crane):
Maintenance Safety:
■
Before lifting, make sure that machine parts (hook and
vibration insulator) are not damaged and screws are not
loosened or lost.
■
■
NEVER lubricate components or attempt service on a
running machine.
ALWAYS allow the machine a proper amount of time to
■
Always make sure crane or lifting device has been properly
secured to the hook of guard frame on compactor.
cool before servicing.
■
■
Keep the machinery in proper running condition.
■
■
■
■
NEVER lift the machine while the engine is running.
Use adequate lifting cable (wire or rope) of sufficient strength.
Use one point suspension hook and lift straight upwards.
Fix damage to the machine immediately and always replace
broken parts.
■
Dispose of hazardous waste properly. Examples of
potentially hazardous waste are used motor oil, fuel and
fuel filters.
NEVER allow any person or animal to stand underneath the
machine while lifting.
■
■
DO NOT use food or plastic containers to dispose of
■
Try not to lift machine to unnecessary heights.
hazardous waste.
Transporting
DO NOT pour waste, oil or fuel directly onto the ground,
down a drain or into any water source.
■
■
ALWAYS shutdown engine before transporting.
Tighten fuel tank cap securely and close fuel cock to prevent
fuel from spilling.
Emergencies:
■
■
Drain fuel when transporting compactor over long distances
or bad roads.
■
ALWAYS know the location of the
nearest fire extinguisher.
ALWAYS tie down the compactor during transportation by
securing the compactor's guard frame with rope.
■
ALWAYS know the location of the
nearest first aid kit.
■
In emergencies always know the location
of the nearest phone or keep a phone on
the job site. Also know the phone numbers of the nearest
ambulance, doctor and fire department. This information
will be invaluable in the case of an emergency.
l
PAGE 10 — MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-90L PLATE COMPACTOR — OPERATION AND SAFETY DECALS
Machine Safety Decals
The MVC-90L Plate Compactor is equipped with a number of safety decals. These decals are provided for operator safety and
maintenance information.The illustration below shows these decals as they appear on the machine. Should any of these decals
become unreadable, replacements can be obtained from your dealer.
Figure 2. Operation and Safety Decals
MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05) — PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-90L PLATE COMPACTOR — GENERAL INFORMATION
Definition of Plate Compactor
Water Tank
The Mikasa MVC-90L is a walk behind, plate compactor
designed for the compaction of sand, mixed soils and asphalt.
This plate compactor is a powerful compacting tool capable of
applying a tremendous force in consecutive high frequency
vibrations to a soil surface. Its applications include compacting
for road, embankments and reservoirs as well as backfilling for
gas pipelines, water pipelines and cable installation work.
The compactor has a built-in water tank which helps provent
damage and adds to long life. Brass water valve eliminates rust
and corrosion problems.
Frequency/Speed
The compactor's vibrating plate has a frequency range between
5,800 vpm (vibrations per minute).The forward and reverse travel
speed of the compactor is approximately 82 ft./minute (25 meters/
minute).
The MVC-90L has a heavy-duty steel base plate with closed
design. It is ribbed for extra strength. The tubular steel roll bar
cage protects engine components and provides a lifting point.
Engine
The Mikasa MVC-90L Plate Compactor is equipped with a Robin
EH172YD4230 gasoline engine. The engine drives an eccentric
weight at a high speed to develop a compaction force.
The MVC-90L also has a reversible, shock-mounted handle.
Vibratory Plate
The vibratory plate of the compactor produce low amplitude
high frequency vibrations, designed to compact granular soils
and asphalt.
Controls
Before starting the MVC-90L Plate Compactor identify and
understand the function of the controls and components.
The resulting vibrations cause forward motion.The engine and
handle are vibration isolated from the vibrating plate.
The double-V belt drive assures less downtine and superior
drive characteristics. Unit can still operate if one belt breaks.
l
PAGE 12 — MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-90L PLATE COMPACTOR — COMPONENTS (PLATE COMPACTOR)
Figure 3. MVC-90L Plate Compactor Components
Figure 3 shows the location of the components and general
maintenance parts. The function of each component is described
below:
1. FuelTank Cap – Remove this cap to add fuel.
6. Vibrating Plate – A flat, open plate made of durable cast
iron construction used in the compacting of soil.
2.
Lifting Bale – When lifting of the compactor is required
either by forklift, crane etc., tie rope or chain around this
lifting point.
7. Vibration Case – Encloses the eccentric, gears and
counter weights.
3. Handle Bar – When operating the compactor use this
8. WaterTube (Sprinkler) – Supplies water to the soil via a
handle bar to manuever the compactor.
splash plate.
4. Engine – This plate compactor uses a Robin
EH172DYD4230 engine. Refer to the Robin owner's
manual for engine information and related topics.
9. Water Shut-Off Valve – Turn this valve downward to let
water flow from the water tank to the water tube.
10. WaterTank – Holds 5.6 quarts of water, built-in.
5. Belt Cover – Remove this cover to gain acess to the V-
belts.NEVER run the compactor without theV-belt cover.If
the V-belt cover is not installed, the possibility exist that
your hand may get caught between the V-belt and clutch,
thus causing serious injury and bodily harm.
11. Water Tank Cap – Remove this cap to add water to the
water tank.
MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05) — PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-90L PLATE COMPACTOR — COMPONENTS (ROBIN EH172YD4230 ENGINE)
Figure 4. Engine Controls and Components
INITIAL SERVICING
The engine (Figure 3) must be checked for proper lubrication and
filled with fuel prior to operation. Refer to the manufacturers engine
manual for instructions & details of operation and servicing. The
engine shown above is a ROBIN engine, operation for other types
of engines may vary somewhat.
Operating the engine without an
air filter, with a damaged air filter,
or a filter in need of replacement
will allow dirt to enter the engine,
causing rapid engine wear.
1. Throttle Lever – Used to adjust engine RPM speed (lever
advanced forward SLOW, lever back toward operator
FAST).
7. Muffler – Used to reduce noise and emissions.
CAUTION - Burn Hazard
2. Fuel Filler Cap – Remove this cap to add unleaded
gasoline to the fuel tank. Make sure cap is tightened
securely.DO NOT over fill.
Enginecomponentscangenerateextremeheat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after
operating. NEVER operate the engine with the
muffler removed.
CAUTION - Fueling The Engine
Adding fuel to the tank should be done only
WARNING
when the engine is stopped and has had an
opportunity to cool down. In the event of a fuel
spill, DO NOT attempt to start the engine until
the fuel residue has been completely wiped
up, and the area surrounding the engine is dry.
8. Choke Lever – Used in the starting of a cold engine, or in
cold weather conditions. The choke enriches the fuel
mixture.
l
9. Engine ON/OFF Switch – ON position permits engine
starting, OFF position stops engine operations.
3. Fuel Tank – Holds unleaded gasoline. For additional
10. Spark Plug – Provides spark to the ignition system. Set
spark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch) Clean
spark plug once a week.
information refer to engine owner's manual.
4. Recoil Starter (pull rope) – Manual-starting method. Pull
the starter grip until resistance is felt, then pull briskly and
smoothly.
11. Oil Dipstick /Filler Port– Remove to determine the amount
oil in engine crankcase. Add oil through this filler port.
5. FuelValve Lever – OPEN to let fuel flow, CLOSE to stop
12. Oil Sensor– In the event of low oil, this sensor will
the flow of fuel.
automatically shut-down the engine.
6. Air Cleaner – Prevents dirt and other debris from entering
the fuel system. Remove wing-nut on top of air filter
cannister to gain access to filter element.
13. Oil Drain Plug– Remove to drain crankcase oil.
PAGE 14 — MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-90L PLATE COMPACTOR — INSPECTION
3. Insert and remove the dipstick without screwing it into the
filler neck. Check the oil level shown on the dipstick.
Before Starting:
CAUTION - General Safety Precautions
4. If the oil level is low (Figure 6), fill to the edge of the oil filler
hole with the recommended oil type (Table 4).Maximum oil
capacity is 400 cc.
NEVER operate the compactor in a confined
area or enclosed area structure that does not
provide ample free flow of air.
ALWAYS wear approved eye and hearing
protection before operating the compactor.
1.
2.
Read safety instructions at the
beginning of manual.
Figure 6. Engine Oil Dipstick
Remove dirt and dust, particularly
in the engine cooling air inlet,
carburetor and air cleaner.
The Oil Alert system will
automatically stop the engine
before the engine falls below safe
limits. Always be sure to check the
engine oil level prior to starting
the engine.
3.
Check the air filter for dirt and dust.
If air filter is dirty, clean or replace the air filter with a new
one as required.
4.
5.
Check carburetor for external dirt and dust.Clean with dry
compressed air.
Table 4. Oil Type
Check fastening nuts and bolts for tightness.
Season
Summer
Spring/Fall
Winter
Temperature
25°C or Higher
25°C~10°C
Oil Type
SAE 10W-30
SAE 10W-30/20
SAE 10W-10
Engine Oil Check
1. To check the engine oil level, place the plate compactor on
secure level ground with the engine stopped.
2. Remove the filler cap/dipstick from the engine oil filler hole
(Figure 5) and wipe it clean.
0°C or Lower
Fuel Check:
1. Remove the gasoline cap located on top of fuel tank.
2. Visually inspect to see if the fuel level is low. If fuel is low,
replenish with unleaded fuel.
3. Whenrefueling,besuretouseastrainerforfiltration.DONOT
top-off fuel.Wipe up any spilled fuel immediately!
WARNING - Explosive Fuel
Explosive Fuel
Figure 5. Engine Oil Dipstick
Gasoline is extremely flammable, and its
vapors can cause an explosion if ignited. DO
NOT start the engine near spilled fuel or
combustible fluids. DO NOT smoke while
refueling.DO NOT attempt to refuel the pump
if the engine is hot! or running.
MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05) — PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-90L PLATE COMPACTOR — START-UP PROCEDURE
This section is intended to assist the operator with the initial
4. Place thechokelever(Figure 10) in the CLOSED position
start-up of the compactor. It is extremely important that this
section be read carefully before attempting to use the compactor
in the field.
if starting a warm engine or the temperature is warm.
Starting the Engine
1. Place the engine fuel valve lever (Figure 7) to the OPEN
position.
Figure 10. Choke Lever (Closed)
5. Place the engine ON/OFF switch (Figure 11) in the ON
position.
Figure 7. FuelValve Lever (Open)
2. Move the throttle lever (Figure 8) away from the slow
position, about 1/3 of the way toward the fast position.
Figure 11. Engine ON/OFF Switch (ON)
6. Grasp the starter grip (Figure 12) and slowly pull it out.The
resistancebecomesthehardestatacertainposition,corre-
sponding to the compression point. Pull the starter grip
briskly and smoothly for starting.
Figure 8. Throttle Lever (Start)
3. Place the choke lever (Figure 9) in the OPEN position if
starting a cold engine.
l
Figure 12. Starter Grip
CAUTION - Using the Recoil Starter Rope
DO NOT pull the starter rope all the way to the end.
DO NOT release the starter rope after pulling. Allow it to
rewind as soon as possible.
Figure 9. Choke Lever (Open)
PAGE 16 — MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-90L PLATE COMPACTOR — STARTUP/SHUT-DOWN PROCEDURES
7. If the engine has started, slowly return the choke lever
(Figure 13) to the CLOSED position. If the engine has not
started repeat steps 1 through 6.
Normal Shutdown
1. Movethethrottlelever tothe IDLEposition (Figure15)and
run the engine for three minutes at idle speed.
Figure 13. Choke Lever (Closed)
Figure 15.Throttle Lever (Idle)
8. Beforethepumpisplacedintooperation,runtheenginefor
several minutes with the throttle lever in the LOW position.
Check for fuel leaks, and noises that would be associated
withlosecomponents.
CAUTION - Stopping the Engine while Working
NEVER stop the engine suddenly while working at high
speeds.This can damage your engine.
9. To begin pumping, place the throttle lever (Figure 14) in the
HIGH speed position.
2. After the engine cools, turn the engine ON/OFF switch to
the OFF position (Figure 16).
Figure 16. Engine ON/OFF Switch (OFF)
Figure 14.Throttle Lever (High Speed)
3. Placethefuelshut-offlever (Figure17) intheOFFposition.
Figure 17. FuelValve Lever (OFF)
Emergency Showdown
1. MovethethrottleleverquicklytotheIDLE position,andplace
the engine ON/OFF switch in the OFF position.
MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05) — PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-90L PLATE COMPACTOR — OPERATION
Operation
CAUTION - General Operation Safety
Operating the Compactor on High Moisture Content Soil
Compactortravelingspeedmaydroponsoilswhichcontainclay,
or other types of soil. Soil with high moisture content can cause
Make sure to follow all safety rules referenced in the safety
sectionofthismanualbeforeoperatingcompactor. Keepwork
areaclearofdebrisandotherobjectsthatcouldcausedamage
to the compactor or bodily injury.
thecompactionplateto"stick"totheground(notliftingupoffthe
ground very fast or high).
To rectify this problem, consider the following:
z
Check the bottom plate to see if clay or equivalent material
has been lodge in the plate mechanism. If so, wash with
water and remove.
1. Oncetheenginehasstarted, movetheenginethrottlelever
quicklytotheFASTposition. Withthethrottleleverinthefast
position, the engine speed should be around 2,300 RPM,
which engages the centrifugal clutch.
z
z
Remember the compactor does not work as efficiently on
clay or soils that have a high moisture content level.
If the soil has a high moisture level, dry soil to appropriate
moisture content level or carry out compaction twice.
Always move the throttle lever
quickly without hesitation.
Increasing the engine speed slowly
causes the clutch to slip and can
damage your clutch.
Using the Compactor Sprinkler System
The MVC-90L is equipped with a watering system that can be
used to wet the ground during compaction to keep dust levels
down.
2. Firmlygaspthecompactor'shandlebar withbothhands as
thecompactorbeginsmovingforward.
To operate the watering system, turn the water cock handle to
open the valve (Figure 18) and start the water flow. With the
compactoratfullspeedandthewatercockfullyopen, thewater
system will provide approximately 20 minutes of sprinkling.
3. Slowlywalkbehindthecompactorandbeonthelookout for
anylargeobjectsorforeignmatterthatmightcausedamage
to the compactor or bodily injury.
Whenever the compactor's vibra-
tion becomes weak or lost during
normal operation regardless of op-
eration hours, check theV-belt and
clutchimmediately.
l
Figure 18.Water System
PAGE 18 — MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-90L PLATE COMPACTOR — MAINTENANCE
Maintenance
TABLE 6. ENGINE INSPECTION
CAUTION - General Maintenance Safety
(For details, see seperate Engine Manual)
Inspection and other services should always be carried out
on hard and level ground with the engine shutdown.
Check Item
Hours of Operation
Fuel or Oil Leakage
Every 8 Hours (Daily)
Inspection and Maintenance ServiceTables.
Fastening Threads
Tightness
Every 8 Hours (Daily)
Every 8 Hours (Daily)
To make sure your plate compactor is always in good working
condition before using, carry out the maintenance inspection in
accordance with Tables 5 through 7.
Check/Replenish
Engine Oil
Daily Service
First 20 hours,
then every 100 hours
z
Check for leakage of fuel or oil.
Replace Engine Oil
z
Remove soil and clean the bottom of compaction plate.
Check engine oil.
Check/Clean the
Air Cleaner
Every 50 hours
z
z
Check for loose screws including tightness. See Table 5
below (tightening torque ), for retightening:
TABLE 7. MVC-90H MACHINE INSPECTION
These inspection intervals are for
operation under normal conditions.
Adjust your inspection intervals
based on the number hours plate
compactor is in use, and particular
working conditions.
HOURS OF
OPERATION
ITEM
REMARKS
Check Before
Daily Operation
Damaged Parts
Every 8 hours
Check Before
Daily Operation
Loose or Lost Screws
Every 8 hours
TABLE 5. TIGHTENING TORQUE
(in. kg/cm) Diameter
Function of Controlling
System Part
Check Before
Daily Operation
Every 8 hours
Every 100 hours
Every 300 hours
Every 200 hours
Material 6mm 8mm 10mm 12mm 14mm 16mm 18mm 20mm
4T
70
150
300
500
500
750 1,100 1,400 2,000
Vibrator Oil Check
6-8T
11T
100 250
150 400
800 1,300 2,000 2,700 3,800
See Page 21
See Page 22
Vibrator Oil
Replacement
800 1,200 2,000 2,900 4,200 5,600
100
(6mm)
300 ~ 350
(8mm)
650 ~ 700
(10mm)
*
V-belt & Clutch Check
* (In case counter-part is of aluminum)
Material and quality of material is marked on each bolt, and screw.
Note: Threads in use with this machine are all right handed
Fuel piping and connections should
be replaced every 2 years.
MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05) — PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-90L PLATE COMPACTOR — MAINTENANCE
Engine Oil Replacement:
Vibrator Oil Check
1. Replace engine oil, in first 20 hours of operation and every
100 hours afterwards.
1. Placethe platecompactorhorizontallyonaflatsurface.Make
sure the compactor is level when checking the oil in the
vibratorassembly.
2. Oil may be drained more easily when it is warm after
operation (For more details, see separate engine Owner's
Manual).
2. Check vibratoroillevelbyremoving theplug (vibrator oilgauge)
asshowninFigure21. Theoillevelshouldbeuptotheoilplug.
The vibrator holds 140 cc (approximately 1 pint).
3. When changing the engine oil, thenold oil can be drained
by removing the oil filler cap, and un-screwing the engine
oil drain plug located at the base of the engine (Figure 19).
4. Remember to refill engine crankcase with the recommended
type of oil as listed in Table 4.
Whenaddingorreplacingoil,replace
using only SAE 10W-30 motor oil.
Figure 19. Engine Oil Plug
Engine Air Cleaner
Figure 21.Vibrator Oil Plug
Changing Vibrator Oil
1. Remove the air cleaner cover and foam filter element as
shown in Figure 20.
1. When changing the vibrator oil, remove the drain plug
located at the bottom of the vibrator (Figure 21),
2. Wash the foam filter element in kerosene or diesel fuel.
Then saturate it in a mixture of 3 parts kerosene or diesel
fuel and 1 part engine oil. Completely squeeze the ele-
ment to remove the
2. Tip the compactor to drain the oil.
mixture and re-install
it back into the air
cleaner.
Vibrator oil will drain more easily
while it is warm.
Figure 20. Air Clean
PAGE 20 — MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-90L PLATE COMPACTOR — MAINTENANCE
Replacing theV-belt
V-Belt Check
1. Remove the belt cover.
CAUTION - Checking and Replacing theV-Belt
2. Place an offset wrench (13 mm) or the like on the vibrator
pulley (lower) fastening bolt.
NEVERattempttochecktheV-beltwith
the engine running. Severe injury can
occurifyourhandgetscaughtbetween
the V-belt and the clutch. Always use
safetygloves.
3. Using a waste cloth or the like, pull theV-belt back strongly at
midway of the belt on the left side and rotate the offset wrench
clockwise so that theV-belt will come off.
4. Check the clutch and replace as necessary, following the
procedures listed in Checking the Clutch.
1. Tocheck theV-belttension,removethethreeboltsthatsecure
the belt cover to the frame as shown in Figure 22.
5. Place the V-belt on the lower vibrator pulley.Push theV-belt
to the left side of the upper clutch and rotate the offset wrench
clockwise so that theV-belt moves onto the pulley.
Checking the Clutch
1. With belt cover removed, visually check outer drum of the
clutch for seizure and "V" groove for wear or damage.
2. Clean the "V" groove as necessary.
3. Check the clutch lining and shoe for signs of wear. If the shoe
is worn, replace the clutch to prevent deficient power
transmission and slippage.
Replacing the Clutch
1. RemoveV-belt.
2. Remove bolt at engine power output by tapping an engaged
wrench (e.g. tapping with hammer) and rotate the bolt
counterclockwise.
3. Remove clutch with a pulley extractor.
4. To install a new clutch, reverse steps 1-3.
Figure 22.V-Belt Cover Removal
2. TheV-belt tension is proper if the V-belt bends 10 to 15 mm
(Figure 23) when depressed with finger at midway between
the clutch and vibration pulley shafts.
Figure 23.V-BeltTension
3. A looseV-belt will decrease the power transmission output,
causing reduced compaction and premature wear of the belt.
4. If theV-belt becomes worn or loose, replace it .
MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05) — PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-90L PLATE COMPACTOR — PREPARATION FOR LONG -TERM STORAGE
Pump Storage
For storage of the pump for over 30 days, the following is required:
z
z
Drain the fuel tank completely.
Run the engine until the fuel in the injection system is
completely consumed.
z
Completely drain the oil from the engine crankcase and follow
procedures described in the engine Owner's Manual for
engine storage.
z
z
z
Completely drain the compactor's hydraulic oil from the
vibrating case.
Clean entire plate compactor, especially the bottom plate
removing all dirt and foreign matter.
Cover plate compactor and engine with plastic covering or
equivalent and store in a clean, dry place.
l
PAGE 22 — MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-90L PLATE COMPACTOR —TROUBLESHOOTING (ENGINE)
Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of a
breakdown, please take a remedial action following the diagnosis based on the EngineTroubleshooting (Table 8) information
shown below and on the following page. If the problem cannot be remedied, please leave the unit just as it is and consult
our company's business office or service plant.
TABLE 8. ENGINE TROUBLESHOOTING
SYMPTOM
POSSIBLE CAUSE
SOLUTION
Check gap, insulation or replace
spark plug.
Spark plug bridging?
Carbon deposit on spark plug?
Clean or replace spark plug.
Difficult to start, "fuel is available, but no
SPARK at spark plug".
Short circuit due to deficient spark plug
insulation?
Check spark plug insulation,
replace if worn.
Improper spark plug gap?
ON/OFF switch is shorted?
Ignition coil defective?
Set to proper gap.
Check switch wiring, replace
switch.
Replace ignition coil.
Set correct spark gap and clean
points.
Difficult to start, "fuel is available, and
SPARK is present at the spark plug".
Improper spark gap, points dirtry?
Condenser insulation worn or short
circuiting?
Replace condenser.
Replace defective spark plug
wiring.
Spark plug wire broken or short circuiting?
Wrong fuel type?
Flush fuel system, and replace
with correct type of fuel.
Difficult to start, "fuel is available, spark
is present and compression is normal"
Water or dust in fuel system?
Air cleaner dirty?
Flush fuel system.
Clean or replace air cleaner.
Re-seat valves.
Suction/exhaust valve stuck or protruded?
Replace piston rings and or
piston.
Piston ring and/or cylinder worn?
Difficult to start, "fuel is available, spark
is present and compression is low"
Cylinder head and/or spark plug not
tightened properly?
Torque cylinder head bolts and
spark plug.
Head gasket and/or spark plug gasket
damaged?
Replace head and spark plug
gaskets.
Fuel not available in fuel tank?
Fill with correct type of fuel.
Apply lubricant to loosen fuel
cock lever, replace if necessary.
Fuel cock does not open properly?
No fuel present at carburetor.
Fuel filter clogged?
Replace fuel filter.
Fuel tank cap breather hole clogged?
Air in fuel line?
Clean or replace fuel tank cap.
Bleed fuel line.
MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05) — PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-90L PLATE COMPACTOR —TROUBLESHOOTING (ENGINE)
TABLE 8. ENGINE TROUBLESHOOTING (CONTINUED)
SYMPTOM
POSSIBLE CAUSE
Air cleaner not clean?
SOLUTION
Clean or replace air cleaner
Check float adjustment, re-build
carbureator.
Improper level in carburetor?
"Weak in power" compression is proper
and does not misfire.
Defective Spark plug?
Defective Spark plug?
Clean or replace spark plug.
Flush fuel system, and replace
with correct type of fuel.
Water in fuel system?
"Weak in power" compression is proper
but misfires.
Dirty spark plug?
Clean or replace spark plug.
Replace ignition coil.
Ignition coil defective?
Replace with correct type of
spark plug.
Spark plug heat value improper?
Engine overheats.
Correct type of fuel?
Replace with correct type of fuel
Clean cooling fins.
Cooling fins dirty?
Governor adjusted correctly?
Governor spring defective?
Adjust governor.
Replace governor spring.
Rotational speed fluctuates.
Check entire fuel system for leaks
or clogs.
Fuel flow restricted?
Recoil mechanism clogged with dust and Clean recoil assembly with soap
dirt?
and water.
Recoil starter malfunction.
Sprial spring loose?
Replace sprial spring.
l
PAGE 24 — MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-90L PLATE COMPACTOR —TROUBLESHOOTING (PLATE COMPACTOR)
Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of a
breakdown, please take a remedial action following the diagnosis based on the Plate Compactor Troubleshooting (Table 9)
information shown below and on the following page. If the problem cannot be remedied, please leave the unit just as it is
and consult our company's business office or service plant.
TABLE 9. PLATE COMPACTOR TROUBLESHOOTING
SYMPTOM
POSSIBLE CAUSE
Engine speed too low?
SOLUTION
Set engine speed to correct RPM.
Check or replace clutch.
Clutch slips?
Travel speed too low, and vibration is
weak.
V-belt slips?
Adjust or replace V-belt.
Excessive oil in vibrator?
Drain excess oil and fill to proper level.
Check eccentric, gears and counter
weights.
Malfunction in vibrator housing?
V-belt slips?
Clutch slips?
Replace V-belt.
Check clutch springs and shoes.
Does not travel forward.
Check vibrator housing (eccentric,
gears and counterweights)
Vibrator locked?
MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05) — PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-90L — EXPLANATION OF PARTS SECTION REMARKS
The following section explains the different symbols and remarks QTY. Column
used in the Parts section of this manual. Use the help numbers
found on the back page of the manual if there are any questions.
Numbers Used - Item quantity can be indicated by a number,
a blank entry, or A/R.
A/R (As Required) is generally used for hoses or other parts
that are sold in bulk and cut to length.
The contents and part numbers listed in the parts section are
subject to change without notice. Multiquip does not
guarantee the availability of the parts listed.
A blank entry generally indicates that the item is not sold
separately. Other entries will be clarified in the “Remarks”
Column.
Sample Parts List:
REMARKS Column
NO. PART NO. PART NAME
QTY. REMARKS
Some of the most common notes found in the “Remarks”
Column are listed below. Other additional notes needed to
describe the item can also be shown.
1
2
2
3
4
12345
BOLT .......................1.... INCLUDES ITEMS W/
WASHER, 1/4 IN. ........... NOT SOLD SEPARATELY
WASHER, 3/8 IN. ....1.... MQ-45TONLY
HOSE .................... A/R.. MAKE LOCALLY
BEARING ................1.... S/N2345B AND ABOVE
*
*
*
12347
12348
12349
Assembly/Kit - All items on the parts list with the same unique
symbol will be included when this item is purchased.
Indicated by:
“INCLUDES ITEMS W/(unique symbol)”
NO. Column
Unique Symbols - All items with same unique symbol
Serial Number Break - Used to list an effective serial number
range where a particular part is used.
( , #,
+
, %, or >) in the number column belong to the same
*
assembly or kit, which is indicated by a note in the “Remarks”
column.
Indicated by:
“S/N XXXXX AND BELOW”
“S/N XXXX AND ABOVE”
“S/N XXXX TO S/N XXX”
Duplicate Item Numbers - Duplicate numbers indicate
multiple part numbers are in effect for the same general item,
such as different size saw blade guards in use or a part that
has been updated on newer versions of the same machine.
Specific Model Number Use - Indicates that the part is used
only with the specific model number or model number variant
listed. It can also be used to show a part is NOT used on a
specific model or model number variant.
When ordering a part that has more
than one item number listed, check
the remarks column for help in
determining the proper part to order.
NOTE
Indicated by:
“XXXXX ONLY”
“NOT USED ON XXXX”
“Make/Obtain Locally” - Indicates that the part can be
purchased at any hardware shop or made out of available
items. Examples include battery cables, shims, and certain
washers and nuts.
PART NO. Column
l
Numbers Used - Part numbers can be indicated by a number,
a blank entry, orTBD.
TBD (To Be Determined) is generally used to show a part that
has not been assigned a formal part number at time of
publication.
“Not Sold Separately” - Indicates that an item cannot be
purchased as a separate item and is either part of an
assembly/kit that can be purchased, or is not available for
sale through Multiquip.
A blank entry generally indicates that the item is not sold
separately or is not sold by Multiquip. Other entries will be
clarified in the “Remarks” Column.
PAGE 26 — MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-90L PLATE COMPACTOR — SUGGESTED SPARE PARTS
MVC-90L
1 TO 3 UNITS
W/ ROBIN EH172YD4230 ENGINE
QTY. P/N
DESCRIPTION
V-BELT, A33
CAP, WATER TANK
SPARK PLUG
ROPE, RECOIL STARTER
ELEMENT, AIR CLEANER
CAP, FUEL TANK
FILTER, FUEL TANK
FILTER, FUEL STRAINER ASSY
SHOCK ABSORBER
THROTTLE WIRE
4
070100340
0430430015
1
3
1
3
1
1
1
4
2
0650149670
2695011008
2273261007
0430430060
0641360010
0642004220
930405011
402313120
MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05) — PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-90L PLATE COMPACTOR — NAME PLATE AND DECALS
NAME PLATE AND DECALS
PAGE 28 — MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-90L PLATE COMPACTOR — NAME PLATE AND DECALS
BODY ASSY.
NO.
1
2
3
4
5
6
7
PART NO.
PART NAME
QTY.
REMARKS
920206290
920203330
920203060
920206280
920203290
920200320
DECAL, READ OPERATORS MANUAL ........................ 1.......... NPA-629
DECAL, HEARING PROTECTION ................................ 1.......... NPA-333
DECAL, OIL CAUTION ................................................. 1.......... NPA-306
DECAL, DANGER PINCH POINT ................................. 1.......... NPA-628
DECAL, CAUTION OPERATING INSTRUCTIONS ....... 1.......... NPA-329
DECAL, WATERTANK .................................................. 1.......... NPA-320
NAME PLATE ............................................................... 1.......... CONTACT PARTS DEPT.
MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05) — PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-90L PLATE COMPACTOR — BODY ASSY.
BODY ASS
PAGE 30 — MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-90L PLATE COMPACTOR — BODY ASSY.
BODY ASSY.
NO.
1
2
3
4
5
6
PART NO.
PART NAME
QTY.
1
4
1
1
12
12
2
4
1
2
1
1
1
2
1
4
11
8
9
9
7
1
4
2
2
4
REMARKS
402100430
930405011
959404350
402010010
020310080
030210250
012010030
031110160
011008035
020308060
402326850
408412320
402420740
070100340
402114100
001200830
030208200
031108160
012112035
030212300
031112230
402010080
930305020
402010020
402402430
952402281
402010110
VIBRATING PLATE
SHOCK ABSORBER
EARTH WIRE
BASE
NUT M10
SW M10
BOLT 10 X 30
PW M10
BOLT 8 X 35
10
13
15
16
17
18
19
20
21
22
23
24
26
27
28
46
47
48
49
50
55
NUT M8
CLUTCH ASSY
KEY 4.78 X 4.78 X 20
SPACER, CLUTCH 19.05 X 27 X 5
V- BELT A33
BELT COVER
BOLT 8 X 30
SW M8
PW M8
BOLT 12X35 H
SW M12
PW M12
HANDLE
SHOCK ABSORBER
PLATE, HANDLE SETTING
BOLT, HANDLE SETTING
WASHER 21363
RETURN SPRING
1
MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05) — PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-90L PLATE COMPACTOR — BODY ASSY. (CONTINUED)
BODY ASSY. (CONTINUED)
PAGE 32 — MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-90L PLATE COMPACTOR — BODY ASSY. (CONTINUED)
BODY ASSY.
PART NO.
NO.
62
68
69
70
71
72
74
75
76
77
78
79
80
81
82
86
87
90
91
92
93
95
96
97
98
99
PART NAME
QTY.
1
1
2
1
1
1
1
1
1
2
2
1
1
1
1
2
1
1
1
1
1
2
2
1
REMARKS
954402131
402010040
402010050
402010060
954401600
952401660
956300060
402313120
501310130
011008020
011008025
401010250
0430430015
911211702
402207080
012010035
402206900
959403750
920200320
920200390
920200650
020108060
030208200
402213820
001220610
030206150
COCK PT1/4
T- JOINT
VINYL PIPE A, 10 X 13 X 380
VINYL PIPE B, 10 X 13 X 350
ELBOW 1/4
WASHER 103045
THROTTLE LEVER ASSY
THROTTLE WIRE S110-250
LEVER HOLDER
BOLT 8X20
BOLT 8X25
SOCKET HEAD BOLT 3/8 -24 X 38
CAP, WATER TANK
ENGINE AY EH172YD4230
ENGINE BASE
BOLT 10 X 30
GUARD
RUBBER, SLIP STOP
DECAL, WATERTANK
PLATE, S. NO./MVC-90L/MQ
DECAL, CAUTION
NUT, M8
SW, M8
PLATE, BACK
BOLT 6 X 10
SW M6
1
2
MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05) — PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-90L PLATE COMPACTOR —VIBRATOR ASSY.
VIBRATOR ASSY.
PAGE 34 — MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-90L PLATE COMPACTOR —VIBRATOR ASSY.
VIBRATOR ASSY.
NO.
PART NO.
408010050
401301260
401601270
401010190
040406309
001220825
030208200
953400270
953405260
401010210
401010220
001211235
030212300
951010090
401010200
401010240
001521230
060403060
920101190
402910010
PART NAME
QTY.
1
1
1
2
REMARKS
1
VIBRATING CASE
CASE, COVER A
CASE, COVER B
PACKING
*
2
3
*
*
4
5
*
BEARING 6309C4
BOLT 8 X 25
SW M8
PLUG, 1/4 X 14 10L
PACKING 1/4 (CU)
PULLEY, VIBRATOR
WASHER 13406
BOLT 12 X 35
2
*
6
7
12
12
1
1
1
1
1
1
1
1
1
2
1
*
*
8
9
*
*
10
*
11
*
12
*
13
*
SW M12
14
KEY 7 X 7 X 23
ROTARY SHAFT
ECCENTRIC ROTATOR
SOCKET HEAD BOLT 12 X 30
OIL SEALTC-35488
DECAL, MOTOR OIL
*
15
*
16
*
17
*
18
20
*
1
*
21
VIBRATOR ASSY ........................................................ 1 .......... INCLUDES ITEMS W/
*
MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05) — PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-90L PLATE COMPACTOR — CLUTCH ASSY. (OLDTYPE)
CLUTCH ASSY. (OLD TYPE)
l
PAGE 36 — MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-90L PLATE COMPACTOR — CLUTCH ASSY. (OLDTYPE)
CLUTCH ASSY. (OLD TYPE)
NO.
73
84
PART NO.
402010150
952403630
030208200
PART NAME
QTY.
REMARKS
BOLT, 5/16-24 UNF-35MM
WASHER 9X30X3
SW M8
1
1
1
94
100
101
102
103
104
105
106
107
CLUTCH ASSY. .............................................. 1 .............. MUST USE NEW CLUTCH ASSY.
PULLEY DRUM A2- 143.................................. 1 .............. MUST USE NEW CLUTCH ASSY.
941020010
941030010
CLUTCH SHOET90
CLUTCH SPRING/1.2X6.5X155
4
2
CLUTCH SHAFT S19.05DL- 65 ...................... 1 .............. MUST USE NEW CLUTCH ASSY.
046006006
080600550
080200300
BEARING 6006DDU
STOP RING AR- 55
STOP RING S- 30
1
1
1
MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05) — PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-90L PLATE COMPACTOR — CLUTCH ASSY. (NEWTYPE)
CLUTCH ASSY. (NEW TYPE)
PAGE 38 — MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-90L PLATE COMPACTOR — CLUTCH ASSY. (NEWTYPE)
CLUTCH ASSY. (NEW TYPE)
NO.
PART NO.
402326850
943040050
943020030
943030030
943050080
080300130
943050070
943010030
046006006
080200300
080100550
PART NAME
QTY.
REMARKS
1
CLUTCH ASSY., A2-143-19 .......................................... 1.......... INCLUDES ITEMS W/
*
2
CLUTCH SHAFT D;19.05/20W
CLUTCH SHOE
CLUTCH SPRING
SPRING PIN (A), CLUTCH
STOP RING E-13
ARM PIN, CLUTCH
PULLEY DRUM /D;143
BEARING 6006DDU2
STOP RING S-30
1
2
4
2
4
2
1
1
1
1
*
3
*
4
*
5
*
6
*
7
*
8
*
9
*
10
*
11
*
STOP RING R-55
MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05) — PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH172YD4230 ENGINE — CRANKCASE GROUP ASSY.
CRANKCASE GROUP ASSY.
PAGE 40 — MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH172YD4230 ENGINE — CRANKCASE GROUP ASSY.
CRANKCASE GROUP ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
10
2691010101
2371420203
0440250010
0600250010
0310060020
0105080290
0105060131
0013906600
0401140030
0211140020
0502100010
0218140010
2531101401
CRANKCASE CP ............................................. 1............. INCLUDES ITEMS W/#
VALVE GUIDE .................................................. 2 ............ OVERSIZE
20
30#
40#
50#
*
OIL SEAL
1
BALL BEARING ............................................... 1............. 6205C3
DOWEL PIN
STUD
STUD
STUD
PLUG
GASKET
UNION
2
2
1
1
1
1
1
1
60
*
70
*
71
*
80
90
100
110
210
SEAL WASHER
MAIN BEARING COVER CP ............................ 1............. INCLUDES ITEMS W/%
OIL SEAL
BALL BEARING ............................................... 1............. 6205C3
220% 0440250020
230% 0600250010
1
250
260
270
280
290
300
310
320
330
340
610
620
630
680
690
700
710
810
820
830
840
850
960
2274500301
2054190103
2696360103
0213160020
2531600203
0130060040
0401100011
0218100010
2531750203
0043505100
2691300101
2531500123
0110080100
2531550103
2691600403
0310060020
0110060020
2531430111
2531440111
2531600633
0110060030
0851080220
2539900107
GOVERNOR GEAR CP
GOVERNOR SLEEVE
OIL GAUGE
1
1
2
2
1
8
1
1
1
1
GASKET
GASKET, BEARING COVER
BOLT AND WASHER AY
PLUG
WASHER, SEAL
SHELTER PLATE
SCREW AND WASHER AY
CYLINDER HEAD CP....................................... 1............. INCLUDES ITEMS W/
GASKET, HEAD
FLANGE BOLT
*
1
4
1
1
2
4
1
1
2
2
1
1
ROCKER COVER
GASKET, ROCKER COVER
DOWEL PIN
FLANGE BOLT
BREATHER COVER CP
BREATHER PLATE CP
GASKET, BREATHER COVER
FLANGE BOLT
RUBBER PIPE
GASKET SET
MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05) — PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH172YD4230 ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
PAGE 42 — MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH172YD4230 ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
NO.
10
40
40
40
50
60
70
PART NO.
PART NAME
QTY.
REMARKS
2532090101
0230250110
0230250120
0230250130
0221814000
0032014000
0323030010
2532250120
2512300103
2692330103
2692340103
2692340203
2692340303
2532350117
2532350217
2532350317
0565160010
CRANKSHAFT CP
1
SPACER T=0.6 .......................................... 1 ............. SELECT ONE SPACER ONLY
SPACER T=0.8 .......................................... 1 ............. SELECT ONE SPACER ONLY
SPACER T=1.0 .......................................... 1 ............. SELECT ONE SPACER ONLY
NUT
1
1
1
SPRING WASHER
WOODRUFF KEY
310
320
CONNECTING ROD ASSY........................ 1 ............. INCLUDES ITEMS W/
CONNECTING ROD BOLT
PISTON PIN
PISTON ..................................................... 1 ............. STANDARD
PISTON ..................................................... 1 ............. OVERSIZE 0.25 MM
PISTON ..................................................... 1 ............. OVERSIZE 0.50 MM
PISTON RING SET ................................... 1 ............. STANDARD
PISTON RING SET ................................... 1 ............. OVERSIZE 0.25 MM
PISTON RING SET ................................... 1 ............. OVERSIZE 0.50 MM
*
2
1
*
350
360
360
360
370
370
370
380
CLIP
2
MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05) — PAGE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH172YD4230 ENGINE — INTAKE AND EXHAUST GROUP ASSY.
INTAKE AND EXHAUST GROUP ASSY.
PAGE 44 — MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH172YD4230 ENGINE — INTAKE AND EXHAUST GROUP ASSY.
INTAKE AND EXHAUST GROUP ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
10
2533170111
2273640103
0051904100
0031522000
2393330113
2533360103
13209KA040
2693340103
2693350103
13210KA031
2693530103
26136001A3
2693580103
0170060090
2693650103
2693010101
2533420111
2533520103
0170080030
0152006090
0152060100
0110060020
2363700101
0150040050
2693480103
CAMSHAFT CP......................................... 1 ............. INCLUDES ITEMS W/
*
35
RELEASE LEVER
SPRING PIN
SNAP RING
1
1
1
2
2
2
1
1
4
2
2
2
2
1
1
1
1
2
4
1
1
1
2
1
*
36
*
37
*
50
TAPPET
60
VALVE SPRING
SPRING RETAINER
INTAKE VALVE
EXHAUST VALVE
COLLET VALVE
PUSH ROD
ROCKER ARM
BOLT, PIVOT
NUT
GUIDE PLATE
MUFFLER CP
MUFFLER COVER
GASKET, MUFFLER
NUT
TAPPING BOLT
TAPPING BOLT
FLANGE BOLT
DEFLECTOR, CP
TAPPING SCREW
EXHAUST PIPE COVER
70
80
90
95
210
220
230
240
260
310
320
340
350
360
363
365
370
380
430
500
2533300101 ............ INTAKE PIPE CP ...................................... 1 ............. INCLUDES ITEM W/ $
STUD
AIR CLEANER ASSY. ............................... 1 ............. INCLUDES ITEMS W/#
505$ 0105060230
510 2533261600
2
510-2# 2363263008
520# 2273261007
PACKING
ELEMENT SET
INSULATOR
GASKET 3, INSULATOR
GASKET INSULATOR
FLANGE BOLT
GASKET 2, INSULATOR
NUT AND WASHER ASSY.
FLANGE NUT
1
1
1
1
1
1
1
2
2
540
550
555
556
560
570
590
2533290103
2533590103
2273590103
0110060130
2373590303
2263921200
0023806000
MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05) — PAGE 45
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH172YD4230 ENGINE — GOVERNOR ASSY.
GOVERNOR ASSY.
PAGE 46 — MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH172YD4230 ENGINE — GOVERNOR ASSY.
GOVERNOR ASSY.
NO.
10
20
25
30
40
50
60
70
PART NO.
PART NAME
QTY.
REMARKS
2534230123
2274220103
0031108000
2534270101
2534280103
0031306000
0011406300
0186060020
2534250123
2694330100
2694330101
2274360103
2694350103
0043104300
2694550303
2274500203
0043106300
0022706000
0110060030
GOVERNOR LEVER
GOVERNOR SHAFT
WASHER
1
1
1
1
1
2
1
1
1
GOVERNOR ROD CP.
ROD SPRING
CLIP
BOLT AND WASHER ASSY.
NUT
GOVERNOR SPRING
SPEED CONTROL ASSY. ........................1 ............. INCLUDES ITEMS W/
SPEED CONTROL CP
KNOB
STOP PLATE
SCREW, PANHEAD
IDLE SET SPRING
SPRING WASHER
SCREW
80
310
320
*
1
1
1
1
1
1
1
1
1
*
330
340
345
346
350
360
370
380
*
NUT
FLANGE BOLT
MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05) — PAGE 47
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH172YD4230 ENGINE — COOLING AND STARTING ASSY.
COOLING AND STARTING GROUP ASSY.
PAGE 48 — MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH172YD4230 ENGINE — COOLING AND STARTING ASSY.
COOLING AND STARTING GROUP ASSY.
NO.
10
20
35
40
45
90
210
210-1
210-2
210-3
210-4
210-5
210-6
210-11
210-35
210-49
220
PART NO.
PART NAME
QTY.
REMARKS
2535125001
2699170303
2699186003
0110060020
0732004950
2535270103
2695020100
2705011508
2695012008
2695011008
2615010008
2705012508
2275013108
2695014508
2705026108
2275015208
0110060010
BLOWER HOUSING, BLACK
LABEL, TRADE MARK
LABEL, ENGINE NAME
FLANGE BOLT
1
1
1
5
1
1
LABEL, RECOIL OHV
HEAD COVER
RECOIL STARTER ASSY. ..................... 1 ............... INCLUDEW/
SPIRAL SPRING
REEL
STARTER ROPE
STARTER KNOB
RATCHET
FRICTION SPRING
STARTER PULLEY
RATCHET GUIDE
SET SCREW
*
1
1
1
1
2
1
1
1
1
4
*
*
*
*
*
*
*
*
*
FLANGE BOLT
MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05) — PAGE 49
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH172YD4230 ENGINE — FUEL GROUP ASSY.
FUEL GROUP ASSY.
PAGE 50 — MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH172YD4230 ENGINE — FUEL GROUP ASSY.
FUEL GROUP ASSY.
NO.
10
20
30
40
PART NO.
PART NAME
QTY.
REMARKS
2536012101
0732003900
0430430060
0641360010
0642008400
0642004220
0642006410
0642007810
0642008410
0642008420
FUEL TANK CP. ........................................1 ............. BLACK
LABEL, CAUTION
FUEL TANK CAP CP
FUEL, FILTER
FUEL, STRAINER ASSY. .........................1 ............. INCLUDES ITEMS W/
FILTER
PACKING
CUP
NUT
O-RING
SCREW, PANHEAD
FUEL PIPE CP .........................................1 ............. INCLUDES ITEMS W/#
RUBBER PIPE
HOSE CLAMP
FLANGE BOLT
1
1
1
50
*
50-1
50-2
50-3
50-4
50-9
1
1
1
1
1
2
*
*
*
*
*
50-13 0642004790
70
80#
90#
105
210
*
2696260101
2696800103
0561110020
0110060030
2536245610
1
2
4
1
CARBURETOR ASSY.
MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05) — PAGE 51
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH172YD4230 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
PAGE 52 — MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH172YD4230 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
210
2536245610
2206253608
2376245108
2366252808
2536242008
2466243608
2366252008
2396256008
2366260008
2366245108
2266255008
1616235208
2366251008
2366255108
2366245008
2366254008
2366250508
2386244008
2536240208
1066239208
2466243508
2096244508
2476255008
2366268008
2366244508
2356242508
2366263108
2466255108
CARBURETOR ASSY. ..................... 1 ............... INCLUDES ITEMS W/
*
210-1
210-2
210-3
210-5
210-6
210-8
210-9
THROTTLEVALVE
SCREW
CHOKE VALVE
PILOT JET
ADJUSTER
CHOKE LEVER
RING
THROTTLE SHAFT
BOLT
RING
NEEDLE
PIN
FLOAT CHAMBER BODY ASSY.
PACKING
PACKING,CHAMBER
FLOAT
MAIN NOZZLE
MAIN JET
SEAL
ADJUST SCREW
SPRING
CAP, CHOKE
SEAL
SPRING
GUIDE HOLDER
RING
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
*
*
*
*
*
*
*
210-11
210-12
210-13
210-14
210-15
210-16
210-17
210-18
210-19
210-20
210-22
210-32
210-40
210-41
210-61
210-62
210-82
210-89
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
210-101
210-121
*
*
CAP
MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05) — PAGE 53
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH172YD4230 ENGINE — ELECTRIC DEVICE GROUP ASSY. (RECOIL START)
ELECTRIC DEVICE GROUP ASSY. (RECOIL START)
PAGE 54 — MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH172YD4230 ENGINE — ELECTRIC DEVICE GROUP ASSY. (RECOIL START)
ELECTRIC DEVICE GROUP ASSY. (RECOIL START)
NO.
10
11
30
60
70
90
95
100
110
PART NO.
PART NAME
QTY.
REMARKS
2697933001
2697943001
0011406250
0660000361
0150040090
0566120050
0659000010
0650149670
0655000051
FLYWHEEL CP
1
1
2
1
2
IGNITION COIL CP
BOLT AND WASHER ASSY.
SWITCH ASSY.
TAPPING SCREW
CLAMP .....................................................1 ............. W/OIL SENSOR ONLY
PLUGTERMINAL
SPARK PLUG
1
1
1
SPARK PLUG CAP
MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05) — PAGE 55
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH172YD4230 ENGINE — OIL SENSOR ASSY.
OIL SENSOR ASSY.
PAGE 56 — MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH172YD4230 ENGINE — OIL SENSOR ASSY.
OIL SENSOR ASSY.
NO.
700
760
765
770
790
795
PART NO.
PART NAME
OIL SENSOR CP 13
WIRE 22 CP
CLAMP CP
CLAMP CP
CLAMP CP
BOLT AND WASHER ASSY.
QTY.
REMARKS
KS31102211
2147312201
2067550101
2077500101
2147900301
0011008160
1
1
1
1
1
3
MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05) — PAGE 57
Download from Www.Somanuals.com. All Manuals Search And Download.
Effective: October 1, 2002
TERMS AND CONDITIONS OF SALE — PARTS
PAYMENTTERMS
5. Partsmustbeinnewandresalablecon-
dition,intheoriginalMultiquippackage(if
any), and with Multiquip part numbers
clearlymarked.
Multiquipreservestherighttoquoteandsell
directtoGovernmentagencies,andtoOrigi-
nal Equipment Manufacturer accounts who
useourproductsasintegralpartsoftheirown
products.
Terms of payment for parts are net 10 days.
FREIGHTPOLICY
All parts orders will be shipped collect or
prepaidwiththechargesaddedtotheinvoice.
All shipments are F.O.B. point of origin.
Multiquip’s responsibility ceases when a
signedmanifesthasbeenobtainedfromthe
carrier,andanyclaimforshortageordamage
mustbesettledbetweentheconsigneeandthe
carrier.
6. Thefollowingitemsarenotreturnable:
SPECIALEXPEDITINGSERVICE
a. Obsolete parts. (If an item is in the
price book and shows as being re-
placedbyanotheritem,itisobsolete.)
A$35.00surchargewillbeaddedtotheinvoice
forspecialhandlingincludingbusshipments,
insuredparcelpostorincaseswhereMultiquip
mustpersonallydeliverthepartstothecarrier.
b. Any parts with a limited shelf life
(such as gaskets, seals, “O” rings,
and other rubber parts) that were
purchasedmorethansixmonthsprior
tothereturndate.
LIMITATIONSOFSELLER’SLIABILITY
MINIMUMORDER
Multiquip shall not be liable hereunder for
damagesinexcessofthepurchasepriceofthe
item with respect to which damages are
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
otherspecial,consequentialorincidentaldam-
ages.
The minimum charge for orders from Mul-
tiquipis$15.00net.Customerswillbeasked
forinstructionsregardinghandlingoforders
notmeetingthisrequirement.
c. Anylineitemwithanextendeddealer
netpriceoflessthan$5.00.
d. Special order items.
RETURNEDGOODSPOLICY
e. Electricalcomponents.
f. Paint,chemicals,andlubricants.
g. Decalsandpaperproducts.
h. Itemspurchasedinkits.
Returnshipmentswillbeacceptedandcredit
willbeallowed,subjecttothefollowingprovi-
sions:
LIMITATIONOFWARRANTIES
Nowarranties,expressorimplied,aremade
in connection with the sale of parts or trade
accessoriesnorastoanyenginenotmanufac-
turedbyMultiquip.Suchwarrantiesmadein
connectionwiththesaleofnew,completeunits
aremadeexclusivelybyastatementofwar-
rantypackagedwithsuchunits,andMultiquip
neitherassumesnorauthorizesanypersonto
assume for it any other obligation or liability
whatever in connection with the sale of its
products.Apartfromsuchwrittenstatementof
warranty, there are no warranties, express,
impliedorstatutory,whichextendbeyondthe
descriptionoftheproductsonthefacehereof.
1. AReturnedMaterialAuthorizationmust
be approved by Multiquip prior to ship-
ment.
7. Thesenderwillbenotifiedofanymaterial
receivedthatisnotacceptable.
8. Suchmaterialwillbeheldforfiveworking
daysfromnotification, pendinginstruc-
tions.Ifareplyisnotreceivedwithinfive
days,thematerialwillbereturnedtothe
senderathisexpense.
2. ToobtainaReturnMaterialAuthorization,
alistmustbeprovidedtoMultiquipParts
Salesthatdefinesitemnumbers,quanti-
ties, and descriptions of the items to be
returned.
9. Creditonreturnedpartswillbeissuedat
dealer net price at time of the original
purchase,lessa15%restockingcharge.
a. Thepartsnumbersanddescriptions
must match the current parts price
list.
10. In cases where an item is accepted, for
which the original purchase document
can not be determined, the price will be
basedonthelistpricethatwaseffective
twelvemonthspriortotheRMAdate.
b. The list must be typed or computer
generated.
l
c. Thelistmuststatethereason(s)for
thereturn.
d. The list must reference the sales
order(s) or invoice(s) under which
theitemswereoriginallypurchased.
11. Credit issued will be applied to future
purchasesonly.
PRICINGANDREBATES
e. The list must include the name and
phonenumberofthepersonrequest-
ingtheRMA.
Prices are subject to change without prior
notice.Pricechangesareeffectiveonaspe-
cificdateandallordersreceivedonorafterthat
datewillbebilledattherevisedprice.Rebates
forpricedeclinesandaddedchargesforprice
increaseswillnotbemadeforstockonhand
atthetimeofanypricechange.
3. AcopyoftheReturnMaterialAuthoriza-
tionmustaccompanythereturnshipment.
4. Freight is at the sender’s expense. All
partsmustbereturnedfreightprepaidto
Multiquip’sdesignatedreceivingpoint.
PAGE 58 — MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
MVC-90L PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #1 (11/01/05) — PAGE 59
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION & PARTS MANUAL
HERE'S HOW TO GET HELP
PLEASE HAVETHE MODEL AND SERIAL
NUMBER ON-HANDWHEN CALLING
UNITED STATES
Multiquip Corporate Office
18910 Wilmington Ave.
Carson, CA 90746
MQ Parts Department
800-427-1244
Tel. (800) 421-1244
Fax (800) 537-3927
Fax: 800-672-7877
Fax: 310-637-3284
310-537-3700
Contact: [email protected]
Mayco Parts
800-306-2926
310-537-3700
Warranty Department
800-421-1244, Ext. 279 Fax:310-537-1173
310-537-3700, Ext. 279
Fax:800-672-7877
Fax:310-637-3284
Service Department
800-421-1244
Technial Assistance
800-478-1244
Fax:310-537-4259
Fax:310-631-5032
310-537-3700
MEXICO
MQ Cipsa
UNITED KINGDOM
Multiquip (UK) Limited Head Office
Hanover Mill, Fitzroy Street,
Ashton-under-Lyne,
Carr. Fed. Mexico-Puebla KM 126.5
Momoxpan, Cholula, Puebla72760Mexico
Tel: (52) 222-225-9900
Fax: (52) 222-285-0420
Tel: 0161 339 2223
Fax: 0161 339 3226
Lancashire OL7 0TL
CANADA
Multiquip
BRAZIL
Multiquip
4110IndustrielBoul.
Laval, Quebec, Canada H7L 6V3
Tel: (450) 625-2244
Fax: (450) 625-8664
Av. Evandro Lins e Silva, 840 - grupo 505 Tel: 011-55-21-3433-9055
Barra de Tijuca - Rio de Janeiro Fax: 011-55-21-3433-9055
© COPYRIGHT 2005, MULTIQUIP INC.
Multiquip Inc., Mikasa, and the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other
trademarks are the property of their respective owners and used with permission.
This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations are based on the MVC-90L Plate Compactor.
Illustrations, descriptions, references and technical data contained in this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the
right to discontinue or change specifications, design or the information published in this publication at any time without notice and without incurring any obligations.
Your Local Dealer is:
Download from Www.Somanuals.com. All Manuals Search And Download.
|