OPERATION AND PARTS MANUAL
SERIES
MODEL MVC77
ONE-WAY PLATE COMPACTOR
(HONDA GX160K1QX2 GASOLINE ENGINE)
Revision #4 (01/14/11)
To find the latest revision of this
publication, visit our website at:
THIS MANUAL MUST ACCOMPANYTHE EQUIPMENT AT ALLTIMES.
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11) — PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
MVC77 Plate Compactor Honda GX160K1QX2 Engine
Proposition 65 Warning ............................................. 2 Cylinder Head Assembly....................................40-41
Table Of Contents ..................................................... 4 Cylinder Barrel (Recoil) Assembly .....................42-43
Parts Ordering Procedures ....................................... 5 Crankcase Cover Assembly...............................44-45
Safety Information................................................ 6-10 Crankshaft Assembly .........................................46-47
Specifications .......................................................... 11 Piston/Rings Assembly.......................................48-49
General Information ................................................ 12 Camshaft Assembly ...........................................50-51
Components............................................................ 13 Recoil Starter .....................................................52-53
Basic Engine ........................................................... 14 Fan Cover Assembly ..........................................54-55
Inspection........................................................... 15-16 Carburetor Assembly .........................................56-57
Startup ............................................................... 17-18 Air Cleaner Assembly.........................................58-59
Operation ................................................................ 19 Muffler Assembly ...............................................60-61
Maintenance ...................................................... 20-21 Fuel Tank Assembly ...........................................62-63
Preparation For Long Term Storage ....................... 22 Cooling Fan & Flywheel Assembly.....................64-65
Troubleshooting ................................................. 23-25 Ignition Coil Assembly ........................................66-67
Explanation Of Codes In Remarks Column ............ 26 Control Assembly ...............................................68-69
Suggested Spare Parts ........................................... 27
Terms and Conditions Of Sale — Parts .................. 70
Component Drawings
Name Plate and Decals ..................................... 28-29
Main Body Assembly.......................................... 30-31
Engine Pulley/Clutch Assembly.......................... 32-33
Vibrator/Plate Mounting Assembly ..................... 34-35
Vibrator Assembly .............................................. 36-37
Water Tank ......................................................... 38-39
l
NOTICE
Specification and part number are subject to
change without notice.
PAGE 4 — MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS ORDERING PROCEDURES
Ordering parts has never been easier!
Choose from three easy options:
Effective:
January 1st, 2006
Best Deal!
Order via Internet (Dealers Only):
Order parts on-line using Multiquip’s SmartEquip website!
If you have an MQ Account, to obtain a Username
and Password, E-mail us at: parts@multiquip.
com.
■ View Parts Diagrams
■ Order Parts
■ Print Specification Information
To obtain an MQ Account, contact your
District Sales Manager for more information.
Use the internet and qualify for a 5% Discount
on Standard orders for all orders which include
complete part numbers.*
to log in and save!
Order Parts
Note: Discounts Are Subject To Change
Fax your order in and qualify for a 2% Discount
on Standard orders for all orders which include
complete part numbers.*
Order via Fax (Dealers Only):
All customers are welcome to order parts via Fax.
Domestic (US) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Note: Discounts Are Subject To Change
Domestic (US) Dealers Call:
Order via Phone:
1-800-427-1244
Non-Dealer Customers:
International Customers should contact
their local Multiquip Representatives for
Parts Ordering information.
Contact your local Multiquip Dealer for
parts or call 800-427-1244 for help in
locating a dealer near you.
When ordering parts, please supply:
❒
Dealer Account Number
❒
Specify Preferred Method of Shipment:
❒
❒
❒
❒
❒
Dealer Name and Address
✓ UPS/Fed Ex
✓ DHL
✓ Truck
■
■
Priority One
Ground
Shipping Address (if different than billing address)
Return Fax Number
■ Next Day
Second/Third Day
Applicable Model Number
■
Quantity, Part Number and Description of Each Part
NOTICE
All orders are treated as Standard Orders and will
ship the same day if received prior to 3PM PST.
WE ACCEPT ALL MAJOR CREDIT CARDS!
MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11) — PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
Do not operate or service the equipment before reading
the entire manual. Safety precautions should be followed
at all times when operating this equipment.
Failure to read and understand the safety
messages and operating instructions could
result in injury to yourself and others.
Potential hazards associated with the operation of this
equipment will be referenced with hazard symbols which
may appear throughout this manual in conjunction with
safety messages.
SAFETY MESSAGES
The four safety messages shown below will inform you
about potential hazards that could injure you or others.The
safety messages specifically address the level of exposure
to the operator and are preceded by one of four words:
DANGER,WARNING, CAUTION or NOTICE.
SAFETY SYMBOLS
DANGER
Indicates a hazardous situation which, if not avoided,
WILL result in DEATH or SERIOUS INJURY.
WARNING
Indicates a hazardous situation which, if not avoided,
COULD result in DEATH or SERIOUS INJURY.
CAUTION
Indicates a hazardous situation which, if not avoided,
COULD result in MINOR or MODERATE INJURY.
NOTICE
Addresses practices not related to personal injury.
l
PAGE 6 — MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
GENERAL SAFETY
CAUTION
NOTICE
„ This equipment should only be operated by trained and
qualified personnel 18 years of age and older.
„ NEVER operate this equipment without proper protective
clothing, shatterproof glasses, respiratory protection,
hearing protection, steel-toed boots and other protective
devices required by the job or city and state regulations.
„ Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
„ Manufacturer does not assume responsibility for any
accident due to equipment modifications. Unauthorized
equipment modification will void all warranties.
„ NEVER use accessories or attachments that are not
recommended by Multiquip for this equipment. Damage
to the equipment and/or injury to user may result.
„ NEVER operate this equipment when not
feeling well due to fatigue, illness or when
under medication.
„ ALWAYS know the location of the nearest
fire extinguisher.
„ NEVER operate this equipment under the influence of
drugs or alcohol.
„ ALWAYS know the location of the nearest
first aid kit.
„ ALWAYS know the location of the nearest phone or keep
a phone on the job site. Also, know the phone numbers
of the nearest ambulance,doctor and fire department.
This information will be invaluable in the case of an
emergency.
„ ALWAYS check the equipment for loosened threads or
bolts before starting.
„ DO NOT use the equipment for any purpose other than
its intended purposes or applications.
„ ALWAYS clear the work area of any debris, tools, etc.
that would constitute a hazard while the equipment is
in operation.
MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11) — PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
COMPACTOR SAFETY
DANGER
WARNING
„ DO NOT place hands or fingers inside engine
compartment when engine is running.
„ NEVER operate the equipment in an explosive
atmosphere or near combustible materials.An
explosion or fire could result causing severe
bodily harm or even death.
„ NEVER operate the engine with heat shields or
guards removed.
„ Keep fingers, hands hair and clothing away
from all moving parts to prevent injury.
WARNING
„ NEVER disconnect any emergency or safety devices.
These devices are intended for operator safety.
Disconnection of these devices can cause severe injury,
bodily harm or even death.Disconnection of any of these
devices will void all warranties.
„ DO NOT remove the radiator cap while the
engine is hot. High pressure boiling water will gush out
of the radiator and severely scald any persons in the
general area of the compactor.
„ DO NOT remove the coolant drain plug
while the engine is hot. Hot coolant will
gush out of the coolant tank and severely
scald any persons in the general area of
the compactor.
CAUTION
„ NEVER lubricate components or attempt service on a
running machine.
NOTICE
„ DO NOT remove the engine oil drain plug while the
engine is hot. Hot oil will gush out of the oil tank and
severely scald any persons in the general area of the
compactor.
„ ALWAYS keep the machine in proper running condition.
„ Fix damage to machine and replace any broken parts
immediately.
CAUTION
„ ALWAYS store equipment properly when it is not being
used.Equipment should be stored in a clean, dry location
out of the reach of children and unauthorized personnel.
„ NEVER touch the hot exhaust manifold,
muffler or cylinder.Allow these parts to cool
before servicing equipment.
ENGINE SAFETY
DANGER
NOTICE
„ NEVER run engine without an air filter or with a dirty air
filter.Severe engine damage may occur.Service air filter
frequently to prevent engine malfunction.
„ The engine fuel exhaust gases contain poisonous carbon
monoxide. This gas is colorless and odorless, and can
l
cause death if inhaled.
„ NEVER tamper with the factory settings
of the engine or engine governor. Damage
to the engine or equipment can result
if operating in speed ranges above the
maximum allowable.
„ The engine of this equipment requires an adequate
free flow of cooling air. NEVER operate this equipment
in any enclosed or narrow
area where free flow of the
air is restricted. If the air
flow is restricted it will cause
injury to people and property
and serious damage to the
equipment or engine.
„ NEVER tip the engine to extreme angles during lifting as
it may cause oil to gravitate into the cylinder head, making
the engine start difficult.
PAGE 8 — MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
FUEL SAFETY
DANGER
BATTERY SAFETY (ELECTRIC START ONLY)
DANGER
„ DO NOT add fuel to equipment if it is placed inside truck
bed with plastic liner. Possibility exists of explosion or
fire due to static electricity.
„ DO NOT drop the battery.There is a possibility that the
battery will explode.
„ DO NOT expose the battery to open flames,
sparks, cigarettes, etc.The battery contains
combustible gases and liquids. If these
gases and liquids come into contact with a
flame or spark, an explosion could occur.
FUEL
WARNING
„ ALWAYS wear safety glasses when
handling the battery to avoid eye irritation.
The battery contains acids that can cause
injury to the eyes and skin.
FUEL
„ Use well-insulated gloves when picking up
the battery.
„ ALWAYS keep the battery charged. If the battery is not
charged, combustible gas will build up.
„ DO NOT start the engine near spilled fuel or combustible
fluids. Diesel fuel is extremely flammable and its vapors
can cause an explosion if ignited.
„ DO NOT charge battery if frozen. Battery can explode.
When frozen, warm the battery to at least 61°F (16°C).
„ ALWAYS refuel in a well-ventilated area, away from
sparks and open flames.
„ ALWAYS recharge the battery in a well-ventilated
environment to avoid the risk of a dangerous concentration
of combustible gases.
„ ALWAYS use extreme caution when working with
flammable liquids.
„ If the battery liquid (dilute sulfuric acid)
comes into contact with clothing or skin,
rinse skin or clothing immediately with
plenty of water.
„ DO NOT fill the fuel tank while the engine is running
or hot.
„ DO NOT overfill tank, since spilled fuel could ignite if it
comes into contact with hot engine parts or sparks from
the ignition system.
„ If the battery liquid (dilute sulfuric acid) comes into
contact with eyes, rinse eyes immediately with plenty
of water and contact the nearest doctor or hospital to
seek medical attention.
„ Store fuel in appropriate containers, in well-ventilated
areas and away from sparks and flames.
CAUTION
„ NEVER use fuel as a cleaning agent.
„ ALWAYS disconnect the NEGATIVE battery terminal
before performing service on the equipment.
„ DO NOT smoke around or near the
equipment. Fire or explosion could result
from fuel vapors or if fuel is spilled on a
hot engine.
„ ALWAYS keep battery cables in good working condition.
Repair or replace all worn cables.
MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11) — PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
TRANSPORTING SAFETY
CAUTION
„ NEVER allow any person or animal to stand underneath
the equipment while lifting.
NOTICE
„ Before lifting, make sure that the equipment parts (hook
and vibration insulator) are not damaged and screws are
not loose or missing.
„ Always make sure crane or lifitng device has been
properly secured to the lifting bail (hook) of the
equipment.
„ ALWAYS shutdown engine before transporting.
„ NEVER lift the equipment while the engine is running.
„ Tighten fuel tank cap securely and close fuel cock to
prevent fuel from spilling.
„ Use adequate lifting cable (wire or rope) of sufficient
strength.
„ Use one point suspension hook and lift straight
upwards.
„ DO NOT lift machine to unnecessary heights.
„ ALWAYS tie down equipment during transport by
securing the equipment with rope.
ENVIRONMENTAL SAFETY
NOTICE
„ Dispose of hazardous waste properly.
Examples of potentially hazardous waste
l
are used motor oil, fuel and fuel filters.
„ DO NOT use food or plastic containers to dispose of
hazardous waste.
„ DO NOT pour waste, oil or fuel directly onto the ground,
down a drain or into any water source.
PAGE 10 — MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
TABLE 1. COMPACTOR SPECIFICATIONS
MVC-77, S, H and SH
Model
Centrifugal Force
Number of Vibrations
Traveling Speed
3,350 lbs. (1520 kg)
5,800 vibrations/min
82 meters/min (82 ft./min)
.49 x .57 cm
(17 x 22 in.)
Plate Size (LxW)
Operating Weight
Operating Weight (Water Tank)
166 lbs. (75.0 kg.)
195 lbs. ( 88.4 kg.)
Water Tank Capacity
13.7 qt.
Max. Area Of Compaction
6970 sq. ft./hr.
TABLE 2. ENGINE SPECIFICATIONSS
Engine Make
HONDA
GX160K1QX2
OHV Gasoline Engine
1
ROBIN
EH172YD4020
OHV Gasoline Engine
1
Engine Model
Engine Type
Number Of Cylinders
68 MM X 45 MM
(2.70 IN X 1.8 IN)
67 MM X 49 MM
(2.64 IN X 1.93 IN)
Bore/Stroke
Displacement
Maximum Output
Oil Grade
163 cc (9.9 cu. in)
5.5 H.P./3,600 rpm
See Table 3
172 cc (10.50 cu. in)
6.0 H.P./4,000 rpm
See Table 3
Oil Capacity
1.3 pints/0.6 liters
Unleaded
1.3 pints/0.6 liters
Unleaded
Fuel Type
Fuel Tank Capacity
Dry Weight
3.8 qt./3.6 liters
15 kg/33 lbs.
3.8 qt./3.6 liters
16 kg/35 lbs.
Starting Method
Recoil Start
Recoil Start
MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11) — PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL INFORMATION
Definition of Plate Compactor
Frequency/Speed
The Mikasa MVC77 Series is a walk behind, plate compactor
designed for the compaction of sand, mixed soils and asphalt.
This plate compactor is a powerful compacting tool capable of
applying a tremendous force in consecutive high frequency
vibrations to a soil surface. Its applications include compacting
for road, embankments and reservoirs as well as backfilling for
gas pipelines, water pipelines and cable installation work.
The compactor's vibrating plate has a frequency range between
5,800 vpm (vibrations per minute).The forward and reverse travel
speed of the compactor is approximately 23 meters/minute (75
ft./minute).
Engine
The Mikasa MVC77 Series Plate Compactor is equipped with
either a Honda or Robin air cooled, 4-cycle gasoline engine.
The engine drives an eccentric weight at a high speed to develop
a compaction force.
Vibratory Plates
The vibratory plates of the compactor produce low amplitude
high frequency vibrations, designed to compact granular soils
and asphalt.
Controls
Before starting the MVC77 Series Plate Compactor identify and
understand the function of the controls and components as
indicated on page 13 (Figure 1).
The resulting vibrations cause forward motion.The engine and
handle are vibration isolated from the vibrating plate.
l
PAGE 12 — MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPONENTS
4
3
2
1
11
W
A
TER
T
ANK
6
10
Mikasa
Mikasa
9
8
7
Figure 1. MVC77 Series Plate Compactor Components
Figures 1 and 2 shows the location of the components and
general maintenance parts. The function of each component is
described below:
6. Belt Cover – Remove this cover to gain acess to the V-
belts.NEVER run the compactor without theV-belt cover.If
the V-belt cover is not installed, the possibility exist that
your hand may get caught between the V-belt and clutch,
thus causing serious injury and bodily harm.
1. Water Tank Cap – Remove this cap to add water to the
water tank.
7. Vibrating Plate – A flat, open plate made of durable cast
2. FuelTank Cap – Remove this cap to add fuel.
iron construction used in the compacting of soil.
3.
Lifting Bale – When lifting of the compactor is required
either by forklift, crane etc., tie rope or chain around this
lifting point.
8. Vibration Case – Encloses the eccentric, gears and
counter weights.
9. WaterTube (Sprinkler) – Supplies water to the soil via a
4. Handle Bar – When operating the compactor use this
splash plate.
handle bar to manuever the compactor.
10. Water Shut-Off Valve – Turn this valve downward to let
5. Gasoline Engine – This plate compactor uses a HONDA
GX160K1QX2 or ROBIN EH172YD4020 engine. Refer to
the HONDA or ROBIN owners manual for engine
information and related topics.
water flow from the water tank to the water tube.
11. Water Tank – Holds 13.7 quarts of water, removable no
tools required.
MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11) — PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC ENGINE
Figure 2. Engine Controls & Components
INITIAL SERVICING
6. Choke Lever – Used in the starting of a cold engine, or in
cold weather conditions. The choke enriches the fuel
mixture.
The engine (Figure 2) must be checked for proper lubrication and
filled with fuel prior to operation. Refer to the manufacturers Engine
manual for instructions & details of operation and servicing.
7. Air Cleaner – Prevents dirt and other debris from entering
the fuel system. Remove wing-nut on top of air filter
cannister to gain access to filter element.
1. Fuel Filler Cap – Remove this cap to add unleaded
gasoline to the fuel tank. Make sure cap is tightened
securely. DO NOT over fill.
NOTICE
WARNING
Operating the engine without an air filter, with a damaged air
filter, or a filter in need of replacement will allow dirt to enter
the engine, causing rapid engine wear.
Add fuel to the tank only when the engine is
stopped and has cooled down. In the event
of a fuel spill, DO NOT attempt to start the
engine until the fuel residue has been
completely wiped up and the area
surrounding the engine is dry.
8. Spark Plug – Provides spark to the ignition system. Set
spark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch) for
HONDA engine, and 0.5 - 0.6 mm (0.020 - 0.024 inch) for
ROBIN engine. Clean spark plug once a week.
l
2. Throttle Lever – Used to adjust engine RPM speed (lever
advanced forward SLOW, lever back toward operator
FAST).
9. Muffler – Used to reduce noise and emissions.
WARNING
3. Engine ON/OFF Switch – ON position permits engine
Engine components can generate extreme
heat.To prevent burns, DO NOT touch these
areas while the engine is running or
immediatelyafteroperating. NEVER operate
the engine with the muffler removed.
starting, OFF position stops engine operations.
4. Recoil Starter (pull rope) – Manual-starting method. Pull
the starter grip until resistance is felt, then pull briskly and
smoothly.
5. FuelValve Lever – OPEN to let fuel flow, CLOSE to stop
10. Fuel Tank – Holds unleaded gasoline. For additional
the flow of fuel.
information refer to engine owner's manual.
PAGE 14 — MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
INSPECTION
Before Starting
NOTICE
1. Read safety instructions at the beginning of manual.
The Oil Alert system will automatically stop the engine
before the engine falls below safe limits. Always be sure
to check the engine oil level prior to starting the engine.
2. Cleanthecompactor,removingdirtanddust.Particularly,the
bottom of the plate, engine cooling air inlet, carburetor and
aircleaner.
3. Checktheairfilterfordirtanddust.Iftheairfilterisdirty,blow
throughtheairfiltercartridgefromtheinside,movingajetof
dry compressed air up and down until all dust is removed.
Otherwise replace air filter with a new one.
Table 3. Oil Type
Season
Summer
Spring/Fall
Winter
Temperature
25°C or Higher
25°C~10°C
Oil Type
SAE 10W-30
SAE 10W-30/20
SAE 10W-10
4. Check carburetor for external dirt and dust. Clean with dry
compressedair.
5. Check fastening nuts and bolts for tightness. Loosened
screws or bolts due to vibration, could lead to unexpected
accident.
0°C or Lower
Gasoline Check
Engine Oil Check
1. Remove the gasoline cap located on top of fuel tank.
2. Visuallyinspecttoseeiffuellevelislow. Iffuelislow,replenish
with unleaded fuel.
1. To check the engine oil level, place the plate compactor on
secure level ground with the engine stopped.
3. When refueling, be sure to use a strainer for filtration. DO
2. Remove the filler cap/dipstick from the engine oil filler hole
(Figure 3) and wipe it clean.
NOT top-off fuel. Wipe up any spilled fuel.
Vibrator Oil Check
1. Place the MVC77 Series plate compactor horizontally on a
flatsurface.Makesurethecompactorislevelwhenchecking
the oil in the vibrator assembly.
2. Check vibratoroillevelbyremoving theplug (vibrator oilgauge)
asshowninFigure5. Theoillevelshouldbeuptotheoilplug.
Thevibratorholds 140cc(approximately1pint).IMPORTANT,
if oil is required, replace using only SAE 10W-30 motor oil.
Figure 3. Engine Oil Dipstick
3. Insertandremovethedipstickwithoutscrewingitintothefiller
neck. Check the oil level shown on the dipstick.
4. If the oil level is low (Figure 4), fill to the edge of the oil filler
hole with the recommended oil type (Table 3).Maximum oil
capacity is 400 cc.
UPPER LIMIT
Figure 5.Vibrator Oil Plug
LOWER LIMIT
Figure 4. Engine Oil Dipstick
MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11) — PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
INSPECTION
2. TheV-belt tension is proper if theV-belt bends 10 to 15 mm
(Figure 8) when depressed with finger at midway between
the clutch and vibration pulley shafts.
V-Belt Check
CAUTION
NEVER attempttochecktheV-beltwiththeenginerunning.
Severe injury can occur of your hand (Figure 6) gets caught
betweentheV-beltandtheclutch.Alwaysusesafetygloves.
CLUTCH
PULLEY
Figure 8.V-BeltTension
3. A looseV-belt will decrease the power transmission output,
causing reduced compaction and premature wear of the
belt.
VIBRATOR
PULLEY
4. If the V-belt becomes worn or loose, replace it by using V-
belt part number 070503350.
Figure 6.V-Belt Hazard
1. To check the V-belt tension, remove the three bolts that
secure the belt cover to the frame as shown in Figure 7.
l
Figure 7.V-Belt Cover Removal
PAGE 16 — MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTUP
CAUTION
NOTICE
DO NOT attempt to run the compactor until the SafeDty
The CLOSED position of the choke lever enriches the
fuel mixture for starting a COLD engine. The OPEN
position provides the correct fuel mixture for normal
operation after starting, and for restarting a warm engine.
Information and Startup sections have been read.
1. Place the fuel valve lever (Figure 9) in the "ON" position.
4. Place the throttle lever (Figure 12) halfway between fast
andslow.
Figure 9. Fuel Valve Lever
2. Place the Engine ON/OFF switch (Figure 10) in the "ON"
position.
Figure 12. Throttle Lever
5. Grasp the starter grip (Figure 13) and slowly pull it out.The
resistancebecomesthehardestatacertainposition,corre-
spondingthecompressionpoint.Rewindtheropealittlefrom
that point and pull out sharply.
CAUTION
DO NOT pull the starter rope all the way to the end.
Figure 10. Engine ON/Off Switch
DO NOT release the starter rope after pulling. Allow it to
rewind as soon as possible.
3. PlacetheChokeLever(Figure11)inthe"OPEN"position.
nn
Figure 13. Starter Grip
Figure 11. Choke Lever
MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11) — PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTUP
6. If the engine has started, slowly return the choke lever
(Figure 11) to the CLOSED position. If the engine has not
started repeat steps 1 through 5.
7. Beforethecompactorisputintooperationruntheenginefor
3-5minutes.
8. Check for abnormal engine noises or fuel leaks.
Stopping the Engine
CAUTION
NEVER stop the engine suddenly while working at high
speeds.
1. Place the throttle lever (Figure 12) in slow position, and
listen for the engine speed to decrease.
2. Place the Engine ON/OFF switch (Figure 11) in the "OFF
"position.
3. Place the fuel valve lever (Figure 9) in the "OFF" position.
l
PAGE 18 — MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Operation
CAUTION
7. Compactortravelingspeedmaydroponsoilswhichcontain
clay, however there may be cases where traveling speed
drops because the compaction plate does not leave the
ground surface easily due to the composition of the soil.To
rectify this problem do the following:
Make sure to follow all safety rules referenced in the safety
sectionofthismanualbeforeoperatingcompactor. Keepwork
area clear of debris and other objects that could cause
damage to the compactor or bodily injury.
Check the bottom plate to see if clay or
equivalent material has been lodge in the
plate mechanism. If so, wash with water and
remove.
1. Oncetheenginehasstarted, movetheenginethrottlelever
quickly to the fastposition.
Remember the compactor does not work as
efficiently on clay or soils that have a high
moisture content level.
2. With the throttle lever in the fast position, the engine speed
should be around 2,300 RPM, therefore engaging the cen-
trifugalclutch.
If the soil has a high moisture level, dry soil
to appropriate moisture content level or carry
out compaction twice.
NOTICE
Always move the throttle lever quickly without hesitation,
because increasing the engine speed slowly causes the
clutch to slip.
5. Firmlygaspthecompactor'shandlebar withbothhands,the
compactor will begin moving forward.
6. Slowlywalkbehindthecompactorandbeonthelookout for
anylargeobjectsorforeignmatterthatmightcausedamage
to the compactor or bodily injury.
MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11) — PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
CAUTION
CAUTION
Inspection and other services should always be carried out
These inspection intervals are for operation under normal
conditions. Adjust your inspection intervals based on the
number hours plate compactor is in use, and particular
working conditions.
on hard and level ground with the engine shutdown.
Inspection and Maintenance ServiceTables.
1. To make sure your plate compactor is always in good
working condition before using, carry out the maintenance
inspection in accordance with Tables 4 through 6.
CAUTION
Fuel piping and connections should be replaced every 2
years.
TABLE 4. MACHINE INSPECTION
Item
Hours of Operation
Remarks
Daily Service
Every 8 hours (every
day)
(Starting check)
Check for leakage of fuel or oil.
Loosened or lost
screws
Every 8 hours (every
day)
Remove soil and clean the bottom of compaction plate.
Check engine oil, see page 13.
Every 8 hours (every
day)
Damage of any part
Check for loose screws including tightness. See Table 6
below (tightening torque ), for retightening:
Function of controlling
system part
Every 8 hours (every
day)
TABLE 6.
Vibrator oil check
Every 100 hours
Every 200 hours
Every 200 hour
See page 19.
TIGHTENING TORQUE (in. kg/cm) Diameter
Vibrator oil
replacement
See page 19.
See page 19.
Material 6mm 8mm 10mm 12mm 14mm 16mm 18mm 20mm
4T
6-8T
11T
*
70
150
250
400
300
500
800
500
800
750
1,100 1,400 2,000
V-belt (clutch) check
100
150
1,300 2,000 2,700 3,800
1,200 2,000 2,900 4,200 5,600
TABLE 5. ENGINE CHECK
100 (6mm) 300 ~ 350 (8mm) 650 ~ 700 (10mm)
(For details, see separate Engine Manual)
* (In case counter-part is of aluminum)
Item
Hours of Operation
(Threads in use with this machine are all right handed)
Leakage of oil or fuel
Every 8 hours (every day)
Every 8 hours (every day)
Material and quality of material is marked on each bolt,
and screw.
Tightness of fastening threads
Every 8 hours (every
day)(Replenish to specified max.
level)
Engine Oil Replacement:
Engine oil check and
replenishment
1. Replace engine oil, in first 20 hours of operation and every
100 hours afterwards.
At first 20 hours, then every 100
hours
Engine oil replenishment
Air cleaner cleaning
2. Oil may be drained more easily when it is warm after
operation (For more details, see separate HONDA or ROBIN
Owner's Manual).
Every 50 hours
3. When changing the engine oil, thenold oil can be drained
by removing the oil filler cap, and un-screwing the engine
oil drain plug located at the base of the engine.
4. Remember to refill engine crankcase with the recommended
type of oil as listed in Table 3.
PAGE 20 — MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
CAUTION
NEVERattempttochecktheV-beltwiththeenginerunning.
Severe injury can occur if your hand (Figure 6) gets caught
betweentheV-beltandtheclutch.Alwaysusesafetygloves.
Checking and Replacing the V-Belt and Clutch
1. After 200 hours of operation, remove the upper belt cover to
check theV-belt tension.Tension is proper if the belt bends
about 10 mm when depressed strongly with finger between
shafts. Loose or worn V-belts reduces power transmission
efficiency, causing weak compaction and reduces the life of
the belt itself.
Figure 14. Engine Oil Plug
Changing Vibrator Oil
CAUTION
Whenever the compactor's vibration becomes weak or lost
duringnormaloperationregardlessofoperationhours,check
theV-beltandclutchimmediately.
1. When changing the vibrator oil, remove the drain plug
located at the bottom- right of the vibrator (Figure 5), and
simply tip the compactor to drain the oil. Note that the oil will
drain more easily while it is hot. Remember to use only
10W-30 motor oil when replaceing vibrator oil.
Replacing the V-belt
Remove the upper and lower belt covers. Engage an offset
wrench (13 mm) or the like to vibrator pulley (lower) fastening
bolt. Engage waste cloth or the like at midway ofV-belt on the left
side and while pulling it back strongly, rotate the offset wrench
clockwise so that theV-belt will come off.
Air Filter
1. The air filter element should be cleaned because a clogged
air cleaner can cause poor engine starting, lack of power
and shorten engine life substantially.
2. To clean or replace air filter loosen the wing nut on the air
filter housing (Figure 15), remove the cover and take out air
filter cartridge. If only cleaning of the air filter is desired blow
through the air filter cartridge from the inside, moving a jet of
dry compressed air up and down until all dust is removed.
Reinstalling the V-belt
EngageV-belt to lower vibrator pulley and push theV-belt to left
side of upper clutch and, in the same manner as in removal,
rotate offset wrench clockwise so that the V-belt goes back on.
Checking Clutch
Check the clutch simultaneously withV-belt checking. With belt
removed, check outer drum of the clutch for seizure and "V"
groove for wear or damage with your eyes. Clean the "V" groove
as necessary. Wear of lining or shoe should be checked with
running check. If the shoe is worn, power transmission becomes
deficient and slipping will result.
Figure 15. Air Filter
MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11) — PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION FOR LONG-TERM STORAGE
Pump Storage
For storage of the pump for over 30 days, the following is
required:
Drain the fuel tank completely.
Run the engine until the fuel in the injection system is
completely consumed.
Completely drain the oil from the engine crankcase and
follow procedures described in the HONDA engine
Owner's Manual for engine storage.
Completely drain the compactor's hydraulic oil from the
vibrating case.
Clean entire plate compactor, especially the bottom plate
removing all dirt and foreign matter.
Cover plate compactor and engine with plastic covering
or equivalent and store in a clean, dry place.
l
PAGE 22 — MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
TABLE 7. ENGINE TROUBLESHOOTING
SYMPTON
POSSIBLE CAUSE
SOLUTION
Check gap, insulation or
replace spark plug.
Spark plug bridging?
Carbon deposit on spark plug?
Clean or replace spark plug.
Difficult to start, "fuel is available, but no
SPARK at spark plug".
Short circuit due to deficient spark plug
insulation?
Check spark plug insulation,
replace if worn.
Improper spark plug gap?
ON/OFF switch is shorted?
Ignition coil defective?
Set to proper gap.
Check switch wiring, replace
switch.
Replace ignition coil.
Set correct spark gap and
clean points.
Difficult to start, "fuel is available, and
SPARK is present at the spark plug".
Improper spark gap, points dirtry?
Condenser insulation worn or short
circuiting?
Replace condenser.
Replace defective spark plug
wiring.
Spark plug wire broken or short circuiting?
Wrong fuel type?
Flush fuel system, and replace
with correct type of fuel.
Difficult to start, "fuel is available, spark
is present and compression is normal"
Water or dust in fuel system?
Air cleaner dirty?
Flush fuel system.
Clean or replace air cleaner.
Re-seat valves.
Suction/exhaust valve stuck or protruded?
Replace piston rings and or
piston.
Piston ring and/or cylinder worn?
Difficult to start, "fuel is available, spark
is present and compression is low"
Cylinder head and/or spark plug not
tightened properly?
Torque cylinder head bolts and
spark plug.
Head gasket and/or spark plug gasket
damaged?
Replace head and spark plug
gaskets.
Fuel not available in fuel tank?
Fill with correct type of fuel.
Apply lubricant to loosen fuel
cock lever, replace if necessary.
Fuel cock does not open properly?
No fuel present at carburetor.
Fuel filter clogged?
Replace fuel filter.
Fuel tank cap breather hole clogged?
Air in fuel line?
Clean or replace fuel tank cap.
Bleed fuel line.
MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11) — PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
TABLE 7. ENGINE TROUBLESHOOTING (CONTINUED)
SYMPTON
POSSIBLE CAUSE
Air cleaner not clean?
SOLUTION
Clean or replace air cleaner
Check float adjustment, re-build
carbureator.
Improper level in carburetor?
"Weak in power" compression is
proper and does not misfire.
Defective Spark plug?
Defective Spark plug?
Clean or replace spark plug.
Flush fuel system, and replace
with correct type of fuel.
Water in fuel system?
"Weak in power" compression is
proper but misfires.
Dirty spark plug?
Clean or replace spark plug.
Replace ignition coil.
Ignition coil defective?
Replace with correct type of
spark plug.
Spark plug heat value improper?
Engine overheats.
Correct type of fuel?
Replace with correct type of fuel
Clean cooling fins.
Cooling fins dirty?
Governor adjusted correctly?
Governor spring defective?
Adjust governor.
Replace governor spring.
Rotational speed fluctuates.
Recoil starter malfunction.
Check entire fuel system for
leaks or clogs.
Fuel flow restricted?
Recoil mechanism clogged with dust and Clean recoil assembly with soap
dirt?
and water.
Sprial spring loose?
Replace sprial spring.
l
PAGE 24 — MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
TABLE 8. PLATE COMPACTOR TROUBLESHOOTING
SYMPTON
POSSIBLE CAUSE
Engine speed too low?
SOLUTION
Set engine speed to correct RPM.
Check or replace clutch.
Clutch slips?
Travel speed too low, and vibration is
weak.
V-belt slips?
Adjust or replace V-belt.
Excessive oil in vibrator?
Drain excess oil and fill to proper level.
Check eccentric, gears and counter
weights.
Malfunction in vibrator housing?
Bearing Failure?
Replace Bearing
Insufficient engine output?
Check engine, compression etc.
MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11) — PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLANATION OF CODES IN REMARKS COLUMN
The following section explains the different symbols and
QTY. Column
remarks used in the Parts section of this manual. Use the
help numbers found on the back page of the manual if there
are any questions.
Numbers Used — Item quantity can be indicated by a
number, a blank entry, or A/R.
A/R (As Required) is generally used for hoses or other
parts that are sold in bulk and cut to length.
NOTICE
The contents and part numbers listed in the parts
section are subject to change without notice.Multiquip
does not guarantee the availability of the parts listed.
A blank entry generally indicates that the item is not sold
separately.Other entries will be clarified in the“Remarks”
Column.
SAMPLE PARTS LIST
REMARKS Column
NO. PART NO. PART NAME
QTY. REMARKS
Some of the most common notes found in the “Remarks”
Column are listed below. Other additional notes needed
to describe the item can also be shown.
1
2%
12345
BOLT......................1 .....INCLUDES ITEMS W/%
WASHER, 1/4 IN............NOT SOLD SEPARATELY
WASHER, 3/8 IN....1 .....MQ-45T ONLY
2% 12347
3
4
12348
12349
HOSE ..................A/R ...MAKE LOCALLY
BEARING ..............1 .....S/N 2345B AND ABOVE
Assembly/Kit — All items on the parts list with the
same unique symbol will be included when this item is
purchased.
NO. Column
Indicated by:
Unique Symbols — All items with same unique
symbol
“INCLUDES ITEMS W/(unique symbol)”
(@, #, +, %, or >) in the number column belong to the
same assembly or kit, which is indicated by a note in the
“Remarks” column.
Serial Number Break — Used to list an effective serial
number range where a particular part is used.
Indicated by:
Duplicate Item Numbers — Duplicate numbers indicate
multiple part numbers, which are in effect for the same
general item, such as different size saw blade guards in
use or a part that has been updated on newer versions
of the same machine.
“S/N XXXXX AND BELOW”
“S/N XXXX AND ABOVE”
“S/N XXXX TO S/N XXX”
Specific Model Number Use — Indicates that the part
is used only with the specific model number or model
number variant listed. It can also be used to show a
part is NOT used on a specific model or model number
variant.
NOTICE
When ordering a part that has more than one item
l
number listed, check the remarks column for help in
determining the proper part to order.
Indicated by:
“XXXXX ONLY”
“NOT USED ON XXXX”
PART NO. Column
Numbers Used — Part numbers can be indicated by a
number, a blank entry, or TBD.
“Make/Obtain Locally” — Indicates that the part can
be purchased at any hardware shop or made out of
available items.Examples include battery cables, shims,
and certain washers and nuts.
TBD (To Be Determined) is generally used to show a
part that has not been assigned a formal part number
at the time of publication.
“Not Sold Separately”— Indicates that an item cannot
be purchased as a separate item and is either part of an
assembly/kit that can be purchased, or is not available
for sale through Multiquip.
A blank entry generally indicates that the item is not sold
separately or is not sold by Multiquip. Other entries will
be clarified in the “Remarks” Column.
PAGE 26 — MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
SUGGESTED SPARE PARTS
MVC77 Series1 TO 5 UNITS WITH HONDA
GX160K1QX2 ENGINE
1 to 3 Units
Qty.
P/N
Description
3 ............ 070503350 ............ V-BELT
1 ............ 060403060 ............ OIL SEAL,VIBRATING
2 ............ 050101000 ............ O-RING (FOR HANDLE)
3 ............ 9807956841 .......... SPARK PLUG (HONDA)
1 ............ 28462ZH8003 ....... ROPE, RECOIL STARTER (HONDA)
1 ............ 36100ZE1015 ....... SWITCH ASSY, ENGINE STOP (HONDA)
3 ............ 17210ZE1505 ....... ELEMENT, A/C (HONDA)
1 ............ 17620ZH7023 ....... CAP, FUEL TANK (HONDA)
1 ............ 17672ZE2W01 ...... FUEL FILTER, FUEL TANK (HONDA)
4 ............ 930405011 ............ SHOCK ABSORBER
MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11) — PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
NAMEPLATE AND DECALS
l
PAGE 28 — MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
NAMEPLATE AND DECALS
NO
PART NO
PART NAME
QTY.
REMARKS
1
2
3
4
5
6
7
8
920203290
920203060
920201580
920106460
920201950
DECAL: CAUTION
1
1
2
1
1
1
1
1
DSC01
DECAL: CAUTION (START ENG/VIBR)
DECAL: MQ LOGO
NPA-306
NPA-158
DECAL: MIKISA LOGO (NAME)
DECAL: MOTOR OIL
PLATE: SERIAL NO./MVC-MQ
DECAL: POWDER COATED
DECAL: EAR PROTECTION LABEL
NPA-507
NPA-195
CONTACT MQ SERVICE DEPT. W/MODEL & S/N
13118
920203330
NPA-333
MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11) — PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
MAIN BODY ASSY.
PAGE 30 — MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
MAIN BODY ASSY.
NO
1
PART NO
PART NAME
QTY.
REMARKS
408105330
930405011
031110160
408105320
408109390
939010010
020310080
030210250
959404350
959404350
031108160
011008040
011208045
030208200
408420810
408420810
408207200
408209910
050200160
020108060
408404240
408104800
014208020
408206161
952402281
952403450
0105091025
408010030
408010080
001221235
030212300
011208045
030208200
920103260
VIBRATING PLATE, 430/77
SHOCK ABSORBER MED-50/S
PLAIN WASHER M10
1
4
4
2
3
4
BASE .......................................................... 1 ............. ROBIN
BASE .......................................................... 1 ............. HONDA
4
5
SHOCK ABSORBER, STOPPER 45
NUT M10
1
9
11
6
7
SPRING WASHER M10
8
SPRING ...................................................... 1 ............. REPLACES 401010020
8
EARTH WIRE
PLAIN WASHER M8
1
9
9
11
12
13
15
15
16
16
17
18
26
27
28
31
32
33
34
36
45
60
61
62
63
72
BOLT 8X40 T.............................................. 4 ............. REPLACES 001220840
BOLT 8X45 T.............................................. 1 ............. REPLACES 001220845
SPRING WASHER 8M
8
ENGINE NUT ............................................. 1 ............. ROBIN
ENGINE NUT ............................................. 2 ............. HONDA
HOOK ......................................................... 1 ............. ROBIN
HOOK ......................................................... 1 ............. HONDA
O-RING
2
1
1
1
NUT M8, H=5
STOPPER
BELT COVER
REPLACES 020408050
BOLT 8X20 T.............................................. 4 ............. REPLACES 001220820
HANDLE
WASHER 21363 (DELRIN)
1
4
WASHER 11X36X4.5 ................................. 2 ............. REPLACES 952400220
BOLT 10X25 T............................................ 2 ............. REPLACES 001221025
PLUG 1/4
HOSE JOINT 1/4X10D
1
1
BOLT 12X35 T............................................ 2 ............. REPLACES 001221235 HONDA
SW M12 ...................................................... 2 ............. HONDA
BOLT 8X45 T.............................................. 2 ............. ROBIN
SPRING WASHER M8 ............................... 2 ............. REPLACES 001220845 ROBIN
PLATE, SERIAL .......................................... 1 ............. CONTACT MULTIQUIP SERVICE DEPT
..................................................................................... WITH MODEL AND SERIAL NUMBER
MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11) — PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGINE PULLEY/CLUTCH ASSY.
ENGINE PULLEY/CLUTCH ASSY.
PAGE 32 — MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGINE PULLEY/CLUTCH ASSY.
ENGINE PULLEY/CLUTCH ASSY.
NO
10
10
10
19
19
20
21
22
23
23
24
25
29
30
50
51
52
53
54
55
56
57
58
59
76
78
79
80
81
82
PART NO
PART NAME
QTY.
REMARKS
EH172YD4020 ENGINE ASSY. (ROBIN) ............................ 1 ............. REPLACES 911202046
ENGINE ASSY. (HONDA) .......................... 1 ............. GX140Q1B5 NO LONGER AVAILABLE
GX160K1QX2 ENGINE ASSY. (HONDA) .......................... 1 ............. REPLACES 912216002
408420830
408434570
408910020
408412320
952403630
009110003
404010060
030208200
070503350
408010060
031110160
943010010
943020010
943050010
943040010
JISB2804C25
943050020
080300090
943030010
080100520
046006250
408910020
16095
CLUTCH SPACER ..................................... 1 ............. ROBIN
SPACER 20X25X8.4/77H .......................... 1 ............. HONDA
CLUTCH ASSSY ........................................ 1 ............. REPLACES 16053
KEY 4.78X4.78X20
1
WASHER 9X30X3 ...................................... 1 ............. HONDA
BOLT 5/16-24 UNF-35MM (HONDA) ........ 1 ............. REPLACES 402010150
BOLT 5/16-24UNF-20MM.......................... 1 ............. HONDA
SPRING WASHER M8 ............................... 1 ............. HONDA
V-BELT ( 3VX-335)
1
SOCKET HEAD BOLT 3/8X32 .................. 1 ............. ROBIN
WASHER 11253......................................... 1 ............. REPLACES 952401440 (ROBIN)
PULLEY DRUM
CLUTCH SHOE
CLUTCH BOSS/D; 19.05
BEARING COLLAR/D; 19.05
1
2
1
1
STOP RING ............................................... 1 ............. REPLACES 080200250
ARM PIN
2
4
2
1
STOP RING
CLUTCH SPRING
STOP RING
BEARING (6205 DDU)............................... 1 ............. REPLACES 046006250
CLUTCH ROTOR ...................................... 1 ............. REPLACES 16093
BEARING 1.1/8” ID X 2.1/8” OD
1
408910020
EM926029
16086
DRUM 4.5/8” (INCLUDES ITEMS 77 & 78) 1 ............. REPLACES 16096
RETAINING RING 1.1/8” DIA
CLUTCH RETAINER
1
1
1
2638
FHSC CAP SCREW 5/16-24 X1
MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11) — PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
VIBRATOR/PLATE MOUNTING ASSY.
PAGE 34 — MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
VIBRATOR/PLATE MOUNTING ASSY.
NO
1
46
47
48
30
PART NO
PART NAME
VIBRATING PLATE
QTY.
1
REMARKS
408105330
012212035
030212300
031112230
408910010
BOLT 12X35 T......................................... 9 ................ REPLACES 001221235
SPRING WASHER M12
PLAIN WASHER M12
9
9
VIBRATOR ASSY. ................................... 1 ................ SEE PAGES 36 AND 37
MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11) — PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
VIBRATOR ASSY.
PAGE 36 — MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
VIBRATOR ASSY.
NO
PART NO
PART NAME
QTY.
REMARKS
1
408010057
401301260
401301270
401010190
040406309
011208025
030208200
953400270
953405260
408420840
401010220
001221235
030212300
951010090
401010200
401010240
014212030
060203030
920101190
408910010
VIBRATING CASE/77,90 .......................... 1 .............. REPLACES 408010050
*
2
CASE COVER/A
CASE COVER/B
PACKING
1
1
2
2
*
3
*
4
*
5
BEARING
*
6
BOLT 8 X 25 T .........................................12 .............. REPLACES 001220825
*
7
SPRING WASHER
PLUG 1/4 X 14
12
1
*
8
*
9
PACKING 1/4 ............................................. 1 .............. REPLACES 953400160
*
10
PULLEY VIBRATOR
WASHER 13406
1
1
*
11
12
13
14
15
16
17
18
20
30
*
*
*
*
*
*
*
*
*
BOLT 12 X 35 T ......................................... 1 .............. REPLACES 001221235
SPRING WASHER M12
KEY 7 X7 X 23
ROTATOR SHAFT
ECCENTRIC ROTATOR
1
1
1
1
SOCKET HEAD BOLT 12 X 30 ................ 2 .............. REPLACES 001521230
OIL SEAL TC-35488 ................................. 1 .............. REPLACES 060403060
DECAL, TURBINE OIL NP -119
1
VIBRATOR ASSY. ..................................... 1 .............. INCLUDES ITEMS W/
*
MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11) — PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
WATER TANK ASSY.
l
PAGE 38 — MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
WATER TANK ASSY.
NO
39
40
41
42
43
44
PART NO
408106380
408316691
408424691
954403240
959403790
402010060
PART NAME
WATER TANK
QTY.
1
REMARKS
CAP, WATER TANK (W/PK) .................... 1 ........REPLACES 408316690
PACKING, 115D-2T
COCK PT 1/4, BH-1211
NUT PS-1/4
1
1
1
VINYL PIPE 9.5X14X450L ...................... 1 ....... REPLACES 408424840
MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11) — PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 — CYLINDER ASSY.
l
PAGE 40 — MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 — CYLINDER ASSY.
NO
1
PART NO
PART NAME
QTY.
1
REMARKS
12210ZH8000 HEAD COMP., CYLINDER
12204ZE01306 GUIDE, INLET VALVE
12205ZE1315 GUIDE, EXHAUST VALVE
12216ZE5300 CLIP, VLAVE GUIDE
12251ZF1800 GASKET, CYLINDER HEAD
12310ZE1010 COVER COMP., HEAD
12391ZE1000 PACKING, HEAD COVER
15721ZH8000 TUBE, BREATHER
2
1
4
1
6
1
7
1
8
1
9
1
10
11
12
13
14
16
17
17
1
90013883000
FLANGE BOLT 6X12
4
90043ZE1020 STUD BOLT 6X112
90047ZE1000 STUD BOLT 8X32
2
2
9430110160
KNOCK PIN 10X16
2
957230806000 FLANGE BOLT 8X60
4
9807956841
9807956854
SPARK PLUG BP6ES NGK
SPARK PLUG W20EP-U DENSO
1
1
MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11) — PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 — CYLINDER BARREL ASSY.
PAGE 42 — MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 — CYLINDER BARREL ASSY.
NO
2
PART NO
PART NAME
QTY.
REMARKS
12000ZH8010 BARREL ASSY. CYLINDER ................. 1 ............INCLUDES ITEMS W/
*
4
16510ZE1000 GOVERNOR ASSY.
1
1
1
2
1
2
1
1
2
1
1
8
9
16531ZE1000 SLIDER, GOVERNOR
16541ZE1000 SHAFT, GOVERNOR ARM
90131ZE1000 BOLT, DRAIN PLUG
90451ZE1000 THRUST WASHER 6MM
90601ZE1000 WASHER, DRAIN PLUG
90602ZE1000 CLIP, GOVERNOR HOLDER
11
12
13
14
15
18
19
21
91202883005
9410106800
9425108000
OIL SEAL 25X41X6
PLAIN WASHER 6MM
LOCK PIN 8MM
*
91001ZF1003 BALL BEARING 6205TMB
*
MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11) — PAGE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 — CRANKCASE COVER ASSY.
PAGE 44 — MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 — CRANKCASE COVER ASSY.
NO
1
PART NO
PART NAME
QTY.
REMARKS
11300ZZE1633
11381ZH8801
15600ZE1003
15600ZG4003
15625ZE1003
15625ZE1003
91202883005
9430108140
COVER ASSY. CRANKCASE...... 1 ............ INCLUDES ITEMS W/
*
4
GASKET CRANKCASE
1
5
6
OIL GAUGE ASSY. ...................... 1 ............ INCLUDES ITEMS W/%
OIL PLUG ASSY. ......................... 1 ............ INCLUDES ITEMS W/#
8#
9%
13
PACKING, OIL FILLER CAP
PACKING, OIL FILLER CAP
OIL SEAL 25X41X6
KNOCK PIN 8X14
FLANGE BOLT 8X32
BALL BEARING 6205
1
1
1
2
6
1
*
14
16
17
957010803200
961006205000
*
MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11) — PAGE 45
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 — CRANKSHAFT ASSY.
PAGE 46 — MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 — CRANKSHAFT ASSY.
NO
2
13
14
15
PART NO
PART NAME
QTY.
REMARKS
13310ZE1000
92101080250A
90473842000
90741883810
CRANKSHAFT COMP.
1
1
1
1
BOLT
WASHER 8MM
KEY 5X5X33
MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11) — PAGE 47
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 — PISTON ASSY.
PISTON ASSY.
l
PAGE 48 — MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 — PISTON ASSY.
PISTON ASSY.
NO
1
PART NO
PART NAME
QTY.
1
REMARKS
13010ZH8941
13011ZH8941
13012ZH8941
13013ZH8941
13101ZH8000
13102ZH8000
13103ZH8000
13104ZH8000
13111ZE1000
13200ZE1010
90001ZE1000
90551ZE1000
RING SET, PISTON (STD)
RING SET, PISTON (0.25)
RING SET, PISTON (0.50)
RING SET, PISTON (0.75)
PISTON (STD)
1
1
1
1
1
1
2
1
2
PISTON (0.25)
1
2
PISTON (0.50)
1
2
PISTON (0.75)
1
3
PISTON PIN
1
4
CONNECTING ROD ASSY. ............ 1 ................... INCLUDES ITEMS W/#
5#
6
CONNECTING ROD BOLT
CLIP, PISTON PIN 18MM
2
2
MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11) — PAGE 49
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 — CAMSHAFT ASSY.
l
PAGE 50 — MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 — CAMSHAFT ASSY.
NO
1
PART NO
PART NAME
QTY.
REMARKS
14100ZE1812
14410ZE1010
14431ZE1000
14441ZE1010
14451ZE1013
14568ZE1000
14711ZF1000
14721ZF1000
14751ZF1000
14771ZE1000
14773ZE1000
14781ZE1000
14791ZE1010
90012ZE0010
90206ZE1000
CAMSHAFT ASSY. ...................... 1 .......... INCLUDES ITEMS W/#
3
PUSH ROD
ARM, VALVE ROCKER
VALVE LIFTER
2
2
2
2
1
1
2
1
1
1
1
1
2
2
5
6
7
PIBOT, ROCKER ARM
SPRING, WEIGHT RETURN
INLET VALVE
EXHAUST VALVE
SPRING, VALVE
RETAINER, INTAKET VALVE
RETAINER, EXHAUST VALVE
ROTATOR, VALVE
PLATE, PUSH ROD GUIDE
PIBOT BOLT 8MM
NUT, PIBOT ADJUSTING
8#
9
10
11
12
13
14
15
16
17
MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11) — PAGE 51
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 — RECOIL STARTER ASSY.
l
PAGE 52 — MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 — RECOIL STARTER ASSY.
NO
1
PART NO
PART NAME
QTY.
REMARKS
28400ZH8013ZA
28400ZH8013ZB
28410ZH8003ZA
28420ZH8013
28422ZH8013
28433ZH8003
28441ZH8003
28442ZH8003
28443ZH8003
28461ZH8003
28462ZH8003
90003ZH8003
957010600800
32901MA1000
RECOIL STARTER*NH1* (RED) ..... 1 ........ INCLUDES ITEMS W/#
1
RECOIL STARTER*NH1* (BLACK) . 1 ........ INCLUDES ITEMS W/#
2#
3#
4#
5#
6#
7#
8#
9#
10#
12#
13
15
CASE COMP., STARTER
REEL RECOIL STARTER
RACHET STARTER
RACHET GUIDE
1
1
2
1
1
1
2
1
1
1
3
1
FRICTION SPRING
SPRING, RECOIL STARTER
SPRING, RETURN
STARTER KNOB
ROPE, RECOIL STARTER
SET SCREW
FLANGE BOLT 6X8
CLIP, CORD
MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11) — PAGE 53
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 — FAN COVER ASSY.
l
PAGE 54 — MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 — FAN COVER ASSY.
NO
3
PART NO
PART NAME
QTY.
1
REMARKS
19610ZE1000ZA
19612ZH8000
19630ZH8000
36100ZE1015
36101ZE1010
90013883000
90022888010
FAN COVER COMP.
7
SIDE PLATE (STD)
1
10
15
16
21
22
SHROUD COMP.
1
SWITCH ASSY. ENGINE STOP
CORD, STOP SWITCH 370MM
FLANGE BOLT 6X12
FLANGE BOLT 6X20
1
1
6
1
MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11) — PAGE 55
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 — CARBURETOR ASSY.
PAGE 56 — MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 — CARBURETOR ASSY.
NO
2#
PART NO
PART NAME
QTY. REMARKS
16010ZE1812
16011ZE0005
16013ZE0005
16015ZE0831
16016ZE0005
16024ZE1811
16028ZE0005
16044ZE0005
16100ZH8822
16124ZE0005
16166ZH8W50
16173001004
16211ZE1000
16220ZE1020
16221ZH8801
16212ZH8800
16610XE1000
16953ZE1812
16954ZE1812
16956ZE1811
16957ZE1812
16967ZE0811
93500030061H
9430520122
GASKET SET
FLOAT VALVE SET
FLOAT SET
1
1
1
3#
4#
5#
FLOAT CHAMBER SET.................. 1 .......INCLUDES O' RING
6#
PILOT SCREW
1
7#
DRAIN SCREW SET....................... 1 .......INCLUDES GASKET
SCREW SET ................................... 1 .......INCLUDES GASKET
8#
9#
CHOKE SET
1
10
CARBURETOR ASSY. .................... 1 .......INCLUDES ITEMS W/#
11#
12#
13#
14
SCREW, THROTTLE STOP
MAIN NOXXLE
1
1
1
1
1
1
1
PACKING, CUP
INSULATOR, CARBURETOR
SPACER COMP., CARBURETOR
PACKING, CARBURETOR
PACKING, INSULATOR
15
16
17
20
CHOKE LEVER COMP. .................. 1 .......INCLUDES ITEM W/
LEVER, COCK
PLATE, LEVER SETTING
SPRING, COCK LEVER
PACKING, FUEL COCK
CUP, FUEL STRAINER
SCREW 3X6
SPRING PIN 2X12
MAIN JET #70
PIOLOT JET SET #35 .................... 1 .......INCLUDES GASKET
*
24#
25#
26#
27#
28#
30#
33
1
1
1
1
1
2
1
1
*
34#
99101ZH80700
99204ZE00350
35#
MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11) — PAGE 57
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 — AIR CLEANER ASSY.
l
PAGE 58 — MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 — AIR CLEANER ASSY.
NO
1
PART NO
PART NAME
PACKING, ELBOW
QTY.
1
REMARKS
16271ZE1000
17210ZE1822
17218ZE1821
17230ZE1820
17232891000
17235ZE1831
17238ZE7010
17239ZE1000
17410ZE1020
90325044000
90325044000
957010602000
9405006000
2
CLEANER ELEMENT.................... 1 ...................... INCLUDES ITEMS W/
*
3
OUTER ELEMENT
1
1
1
1
2
1
*
*
4
COVER, AIR CLEANER
GROMET, AIR CLEANER
NOSE, SILENCER
5
6
7%
8%
9
COLLAR, AIR CLEANER
COLLAR (B), AIR CLEANER
ELBOW COMP., AIR CLEANER ... 1 ...................... INCLUDES ITEMS W/%
12
13
14
15
NUT
NUT
1
1
1
2
FLANGE BOLT 6X20
FLANGE BOLT 6MM
MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11) — PAGE 59
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 — MUFFLER ASSY.
l
PAGE 60 — MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 — MUFFLER ASSY.
NO
2
PART NO
PART NAME
QTY.
1
REMARKS
18310ZF1000
19320ZF1H01
18325ZE1010
18340ZE1010
18381ZH8800
18522ZE1000
90050ZE1000
90055ZE1000
90002ZG0003
94001080000S
MUFFLER COMP.
MUFFLER PROCTOR (STD)
PROCTECTOR, LOWER
DEFLECTOR CP
3
1
5
1
7
1
9
GASKET, MUFFLER
GUIDE, MUFFLER
TAPPING SCREW 5X8
TAPPING SCREW 4X6
TAPPING SCREW 4X8
NUT
1
10
11
12
13
14
1
4
3
2
2
MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11) — PAGE 61
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 — FUEL TANK ASSY.
l
PAGE 62 — MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 — FUEL TANK ASSY.
NO
10
17
20
21
23%
24
29
33
36
40
43
PART NO
PART NAME
QTY.
REMARKS
16854ZH8000
16955ZE1000
17510ZE1020ZA
17620ZH7023
17631ZH7003
17672ZE2W01
91353671004
9405006000
RUBBER, SUPPORT (107MM)
JOINT, FUEL TANK
FUEL TANK COMP.
1
1
1
FUEL TANK CAP CP ..................... 1 ............................ INCLUDES ITEMS W/%
PACKING
FUEL FILTER
1
1
1
2
1
2
1
O-RING 14MM
FLANGE NUT 6MM
FUEL TUBE 4.5X140
CLIP, TUBE
950014514040
9500202080
957010602500
FLANGE BOLT 6X25
MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11) — PAGE 63
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 — COOLING FAN & FLYWHEEL ASSY.
l
PAGE 64 — MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 — COOLING FAN & FLYWHEEL ASSY.
NO
1
5
6
10
11
PART NO
PART NAME
QTY.
REMARKS
19511ZE1000
28451ZH8003
31100ZE1010
90201878003
13331357000
COOLING FAN
1
1
1
1
1
STARTER PULLEY
FLYWHEEL COMP.
SPECIAL NUT 14MM
WOODRUFF KEY 25X18
MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11) — PAGE 65
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 — IGNITION COIL ASSY.
PAGE 66 — MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 — IGNITION COIL ASSY.
NO
1
2
PART NO
PART NAME
QTY.
REMARKS
30500ZE1033
30600ZE1013
90121952000
IGNITION COIL CP ASSY.
SPARK PLUG CAP ASSY.
FLANGE BOLT 6X25
1
1
2
14
MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11) — PAGE 67
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 — CONTROL ASSY.
l
PAGE 68 — MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 — CONTROL ASSY.
NO
2
PART NO
PART NAME
QTY.
1
REMARKS
16551ZE0010
16555ZE1000
16561ZE1020
16562ZE1020
16500ZH8812
16571ZH8010
16574ZE1000
16575ZH8000
16576891000
16578ZE1000
16580ZH8812
16584883300
16592ZE1810
16594883010
90013883000
90015ZE5010
90605230000
93500040060H
93500050250H
93500050160A
90114SA0000
940500600
GOVERNOR ARM
GOVERNOR ROD
GOVERNOR SPRING
SRRING, THROTTLE
CONTROL ASSY.
LEVER CONTROL
LEVER SPRING
3
1
4
1
5
1
7
1
9
1
10
11
12
13
15
16
17
18
21
22
24
26
27
28
29
30
1
WASHER, CONTROL LEVER
HOLDER, CABLE
SPACER, CONTROL LEVER
CONTROL BASE COMP.
ADJUSTING SPRING
SPRING, CABLE, RETURN
WIRE HOLDER
1
1
1
1
1
1
1
FLANGE BOLT 6 X 12
BOLT, GOVERNOR
CIR CLIP
2
1
1
SCREW 4 X 6
1
SCREW 5X 25
1
SCREW 5X 16
1
LOCK NUT 6MM
1
FLANGE NUT 6MM
1
MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11) — PAGE 69
Download from Www.Somanuals.com. All Manuals Search And Download.
TERMS AND CONDITIONS OF SALE — PARTS
5. Parts must be in new and resalable
condition, in the original Multiquip
package (if any), and with Multiquip part
numbers clearly marked.
Multiquip reserves the right to quote and
sell direct to Government agencies, and to
Original Equipment Manufacturer accounts
who use our products as integral parts of their
own products.
PAYMENT TERMS
Terms of payment for parts are net 30 days.
FREIGHT POLICY
6. The following items are not returnable:
All parts orders will be shipped collect or
prepaid with the charges added to the invoice.
All shipments are F.O.B. point of origin.
Multiquip’s responsibility ceases when a
signed manifest has been obtained from the
carrier, and any claim for shortage or damage
must be settled between the consignee and
the carrier.
a. Obsolete parts. (If an item is in the
price book and shows as being
replaced by another item, it is
obsolete.)
SPECIAL EXPEDITING SERVICE
A $35.00 surcharge will be added to the
invoice for special handling including bus
shipments, insured parcel post or in cases
where Multiquip must personally deliver the
parts to the carrier.
b. Any parts with a limited shelf life
(such as gaskets, seals, “O” rings,
and other rubber parts) that were
purchased more than six months
prior to the return date.
LIMITATIONS OF SELLER’S LIABILITY
MINIMUM ORDER
Multiquip shall not be liable hereunder for
damages in excess of the purchase price of
the item with respect to which damages are
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
other special, consequential or incidental
damages.
The minimum charge for orders from Multiquip
is $15.00 net. Customers will be asked for
instructions regarding handling of orders not
meeting this requirement.
c. Any line item with an extended
dealer net price of less than
$5.00.
d. Special order items.
RETURNED GOODS POLICY
e. Electrical components.
f. Paint, chemicals, and lubricants.
g. Decals and paper products.
h. Items purchased in kits.
Return shipments will be accepted and
credit will be allowed, subject to the following
provisions:
LIMITATION OF WARRANTIES
No warranties, express or implied, are
made in connection with the sale of parts or
trade accessories nor as to any engine not
manufactured by Multiquip. Such warranties
made in connection with the sale of new,
complete units are made exclusively by a
statement of warranty packaged with such
units, and Multiquip neither assumes nor
authorizes any person to assume for it
any other obligation or liability whatever in
connection with the sale of its products. Apart
from such written statement of warranty,
there are no warranties, express, implied or
statutory, which extend beyond the description
of the products on the face hereof.
1. A Returned Material Authorization
must be approved by Multiquip prior to
shipment.
7. The sender will be notified of any material
received that is not acceptable.
8. Such material will be held for five
working days from notification, pending
instructions. If a reply is not received
within five days, the material will be
returned to the sender at his expense.
2. To obtain a Return Material Authorization,
a list must be provided to Multiquip
Parts Sales that defines item numbers,
quantities, and descriptions of the items
to be returned.
9. Credit on returned parts will be issued
at dealer net price at time of the original
purchase, less a 15% restocking
charge.
a. The parts numbers and descriptions
must match the current parts price
list.
b. The list must be typed or computer
generated.
10. In cases where an item is accepted, for
which the original purchase document
can not be determined, the price will be
based on the list price that was effective
twelve months prior to the RMA date.
c. The list must state the reason(s)
for the return.
l
Effective: February 22, 2006
d. The list must reference the sales
order(s) or invoice(s) under
which the items were originally
purchased.
11. Credit issued will be applied to future
purchases only.
PRICING AND REBATES
e. The list must include the name
and phone number of the person
requesting the RMA.
Prices are subject to change without prior
notice. Price changes are effective on a
specific date and all orders received on or
after that date will be billed at the revised price.
Rebates for price declines and added charges
for price increases will not be made for stock
on hand at the time of any price change.
3. AcopyoftheReturnMaterialAuthorization
must accompany the return shipment.
4. Freight is at the sender’s expense. All
parts must be returned freight prepaid to
Multiquip’s designated receiving point.
PAGE 70 — MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC77 PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (1/14/11) — PAGE 71
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND PARTS MANUAL
HERE’S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
UNITED STATES
Multiquip Corporate Office
MQ Parts Department
18910 Wilmington Ave.
Carson, CA 90746
Contact: [email protected]
Tel. (800) 421-1244
Fax (800) 537-3927
800-427-1244
310-537-3700
Fax: 800-672-7877
Fax: 310-637-3284
Service Department
Warranty Department
800-421-1244
310-537-3700
Fax: 310-537-4259
Fax: 310-943-2238
800-421-1244
310-537-3700
Fax: 310-943-2249
Technical Assistance
800-478-1244
MEXICO
UNITED KINGDOM
MQ Cipsa
Multiquip (UK) Limited Head Office
Carr. Fed. Mexico-Puebla KM 126.5
Momoxpan, Cholula, Puebla 72760 Mexico
Contact: [email protected]
Tel: (52) 222-225-9900
Unit 2, Northpoint Industrial Estate, Tel: 0161 339 2223
Fax: (52) 222-285-0420 Globe Lane,
Dukinfield, Cheshire SK16 4UJ
Contact: [email protected]
Fax: 0161 339 3226
CANADA
Multiquip
4110 Industriel Boul.
Laval, Quebec, Canada H7L 6V3
Contact: [email protected]
Tel: (450) 625-2244
Tel: (877) 963-4411
Fax: (450) 625-8664
© COPYRIGHT 2011, MULTIQUIP INC.
Multiquip Inc, the MQ logo and the Mikasa logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks
are the property of their respective owners and used with permission.
This manual MUST accompany the equipment at all times.This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data contained in
this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications, design or the information published
in this publication at any time without notice and without incurring any obligations.
Your Local Dealer is:
Download from Www.Somanuals.com. All Manuals Search And Download.
|