24-Port + One Dual-Module
Expansion Slot
Stackable Managed Switch
MIL-SM2401M-STK
USER GUIDE
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
1. Introduction
Features
Software Features
Package Contents
Management Methods
Console and Telnet Management
Web-based Management
SNMP Network Management
Ethernet Switching Technology
2. Hardware Description
Front Panel
LED Indicators
Rear Panel
Desktop Installation
Rack-mounted Installation
Power On
3. Network Application
Small Workgroup
Segment Bridge
Stacking Workgroup
4. Console Management
Connecting a Terminal or PC to the Console Port
Communication Parameters
Console - Login
Console Management Options
5. CLI Management Interface
5-1. Commands Level
5-2. Commands Set List
5-2-1. System Commands Set
5-2-2. Port Commands Set
5-2-3. Trunk Commands Set
5-2-4. VLAN Commands Set
Download from Www.Somanuals.com. All Manuals Search And Download.
5-2-5. Spanning Tree Commands Set
5-2-6. QoS Commands Set
5-2-7. IGMP Commands Set
5-2-8. Mac/Filter Table Commands Set
5-2-9. SNMP Commands Set
5-2-10. Port Mirroring Commands Set
5-2-11. Stacking Commands Set
5-2-12. 802.1x Commands Set
5-2-13. TFTP Commands Set
6. Console Menu Management
6-1. Main Menu
6-2. Status and Counters
6-2-1. Port Status
6-2-2. Port Counters
6-2-3. System Information
6-3. Switch Configuration
6-3-1. Administration Configuration
6-3-1-1. Device Information
6-3-1-2. IP Configuration
6-3-1-3. User Name Configuration
6-3-1-4. Password Configuration
6-3-2. Port Configuration
6-3-3. Trunk Configuration
6-3-4. Port Mirroring Configuration
6-3-5. VLAN Configuration
6-3-5-1. VLAN Configure
6-3-5-2. Create a VLAN Group
6-3-5-3. Edit / Delete VLAN Group
6-3-5-4. Groups Sorted Mode
6-3-6. Priority Configuration
6-3-7. MAC Address Configuration
6-3-7-1. Static MAC Address
6-3-7-2. Filtering MAC Address
6-3-8. Miscellaneous Configuration
Download from Www.Somanuals.com. All Manuals Search And Download.
6-3-8-1. MAC Address Ageing Time
6-3-8-2. Broadcast Storm Filtering
6-3-8-3. Max Bridge Transmit Delay Bound
6-3-8-4. Collision Retry Forever
6-3-8-5. Hash Algorithm
6-3-8-6. IFG Compensation
6-3-8-7. IP Stacking Group ID (0…65535)
6-3-8-8. IP Stacking Mode
6-4. Protocol Related Configuration
6-4-1. STP
6-4-1-1. STP Setup
6-4-1-2. System Configuration
6-4-1-3. STP Per Port Setting
6-4-2. SNMP
6-4-2-1. SNMP System Options
6-4-2-2. Community Strings
6-4-2-3. Trap Managers
6-4-3. LACP
6-4-3-1. LACP Working Ports
6-4-3-2. LACP State Activity
6-4-3-3. LACP Group Status
6-4-4. IGMP/GVRP Configuration
6-4-5. 802.1X Configuration
6-4-5-1. 802.1X Setup
6-4-5-2. 802.1X System Configuration
6-4-5-3. 802.1X Per Port Configuration
6-4-5-4. 802.1X Miscellaneous Configuration
6-5. System Reset Configuration
6-5-1. Factory Default
6-5-2. System Reboot
6-5-3. TFTP Configuration
6-5-3-1. TFTP Update Firmware
6-5-3-2. TFTP Restore Configuration
6-5-3-3. TFTP Backup Configuration
Download from Www.Somanuals.com. All Manuals Search And Download.
6-5-3-4. Save Configuration
6-6. Xmodem Upgrade
7. Web-Based Management
7-1. System Login
7-2. Port Status
7-3. Port Statistics
7-4. Administrator
7-4-1. IP Address
7-4-2. Switch Setting
7-4-2-1. Basic Switch Settings
7-4-2-2. Advanced Settings
7-4-2-3. Miscellaneous Settings
7-4-3. Console Port Information
7-4-4. Port Controls
7-4-5. Trunking
7-4-5-1. Aggregator Setting
7-4-5-2. Aggregator Information
7-4-5-3. State Activity
7-4-6. Forwarding and Filtering
7-4-6-1. IGMP Snooping
7-4-6-2. Static MAC Address
7-4-6-3. MAC Filtering
7-4-7. VLAN Configuration
7-4-7-1. VLAN Operation Mode 802.1Q (802.1Q VLAN)
7-4-8. Spanning Tree
7-4-8-1. System Configuration
7-4-8-2. Per Port Configuration
7-4-9. Port Mirroring
7-4-10. SNMP Management
7-4-10-1. System Options
7-4-10-2. Community Strings
7-4-10-3. Trap Managers
7-4-11. Security Manager
7-4-12. 802.1X
Download from Www.Somanuals.com. All Manuals Search And Download.
7-4-12-1. System Configuration
7-4-12-2. Per Port Configuration
7-4-12-3. 802.1X Miscellaneous Configuration
7-4-13. TFTP Update Firmware
7-4-14. Configuration Backup
7-4-14-1. TFTP Restore Configuration
7-4-14-2. TFTP Backup Configuration
7-4-15. Factory Default
7-4-16. System Reboot
7-5. Panel List
7-6. IP Stacking
7-6-1. Setting up an IP Stacking Group
8. Troubleshooting
Incorrect connections
Diagnostic LED Indicators
9. Technical Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
1.
Introduction
The MIL-SM2401M-STK managed switch is a multi-port switch that can be used
to build high-performance switched workgroup networks. This switch is a
store-and-forward device that offers low latency for high-speed networking. The
switch is targeted at workgroup, department or backbone computing
environments.
The switch features a “store-and-forward “ switching scheme. This allows the
switch to auto-learn and store source addresses in an 8K-entry MAC address
table.
The
(Medium Dependent Interface) port is also called an "uplink port". The
MDI
MDI port does not cross transmit and receive lines, which is done by the regular
ports (MDI-X ports) that connect to end stations. In general, MDI means
connecting to another hub or switch while MDIX means connecting to a
workstation or PC. Therefore,
means that you can connect to
Auto MDI/MDIX
another switch or workstation without changing non-crossover or crossover
cabling.
The MIL-SM2401M-STK switch provides 24 auto-sensing 10/100Base-TX RJ-45
ports plus one dual-port expansion slot for optional fiber, gigabit fiber, or gigabit
UTP modules, which enables long-distance fiber connections or gigabit copper for
higher connection speeds.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
„ Conforms to IEEE802.3 10BASE-T, 802.3u 100BASE-TX/FX, 802.3ab
1000BASE-T, 802.3z Gigabit fiber
„ 24 10/100 Ethernet ports plus one expansion slot
„ IEEE802.3x Flow control
¾ Flow control for full duplex
Bullets and Numbering
Formatted:
¾ Backpressure for half duplex
„ High back-plane bandwidth 8.8Gbps
„ IEEE802.3ad Port trunk with LACP
„ Broadcast storm filter
„ Stack management via single IP address
„ IGMP support for Multi Media application
„ EEE 802.1p class of service
„ Port security
„ Port bandwidth control
„ IEEE 802.1d Spanning tree protocol
„ GVRP function
„ Port based VLAN/802.1Q VLAN
„ IEEE 802.1x user authentication
„ DHCP client
„ SNMP, Telnet, Web and Local console management
„ Provides command line interface for telnet and local console
management
„ Modules include: 2 x 100FX, 2 x 1000SX, 1000T + 1000SX, 1000T +
1000LX, 2 x 1000T, 2 MINI GBIC
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Software Features
Management
Provides SNMP, Web browser, Telnet and local RS-232
console management. The telnet and console also
supports command line interface.
RFC 1157 SNMP, RFC 1213 MIB II, RFC 1643 Ethernet
like, RFC 1493 Bridge MIB, RFC 1757 RMON 1, RFC 1215
Trap, RFC 2674 VLAN MIB, private MIB.
RFC Standard
Cold start, link down, link up, authorization fail, Trap station
up to 3.
SNMP Trap
Software Upgrade
TFTP and Console firmware upgradeable
Supports IEEE802.3ad with LACP function. Up to 7 trunk
groups and group member up to 4. The trunk port within
24-port 10/100TX and extension module.
Port Trunk
Spanning Tree
IEEE802.1d Spanning Tree
Port based VLAN
IEEE802.1Q Tag VLAN
IEEE802.1v Protocol VLAN (IP, IPX, etc.)
The static VLAN groups up to 256 and dynamic VLAN
groups up to 2048, the VLAN ID can be assigned from 0 to
4094.
VLAN
QOS Policy
Supports 8 priority levels ID for two priority queues
Per system supports high and low queues. The priority
service rule: first come first service, all High before Low,
WRR for high or low weight.
Class of Service
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Supports 3 settings: “Disable, Low or High priority”. When
set to “Disable”, the incoming packet will follow QoS policy;
Otherwise, the packet will follow port priority setting to
“High/Low” queue.
Port Based Priority
Supports IGMP snooping for Multi-Media application and
supports 256 groups
IGMP
Supports ingress and egress MAC address filter and static
source MAC address lock.
Port Security
Global system supports 3 mirroring types: “RX, TX and
Both packet”. The maximum of port mirror entries is up to
25.
Port Mirror
Bandwidth Control
Each port supports bandwidth control. Per level 100Kbps.
Supports single IP management feature, stacked up to 8
units. Stacking and switch management can be through
any port, including the uplink module.
Stacking
802.1x
Supports IEEE802.1x User-Authentication and can report
to RADIUS server.
„
„
„
„
Reject
Accept
Authorize
Disable
DHCP
DHCP Client
Packet filter
Broadcast storm
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Package Contents
Unpack the contents of the package and verify them against the checklist below.
„ MIL-SM2401M-STK Switch
„ Power Cord
„ Four Rubber Feet
„ Rack Mount Ears
„ RS-232 cable
„ User Guide (CD Manual)
„ Warranty Card
If any item is missing or damaged, please contact your local dealer for service.
Management Methods
The MIL-SM2401M-STK switch series supports the following management
methods:
„
„
„
Console and Telnet Management
Web-based Management
SNMP Network Management
Console and Telnet Management
Console Management is done through the RS-232 Console Port. Managing the
switch in this method requires a direct connection between a PC and the switch.
Telnet management requires a network connection. The default IP address is
5
Download from Www.Somanuals.com. All Manuals Search And Download.
192.168.1.77 with a subnet mask of 255.255.255.0. This default address can be
used to login and change the configuration using Telnet.
Web-based Management
The switch provides an embedded HTML web server residing in flash memory. It
offers advanced management features and allows users to manage the switch
from anywhere on the network through a standard browser such as Microsoft
Internet Explorer or Netscape.
SNMP Network Management
SNMP (Simple Network Management Protocol) provides a means to monitor and
control network devices, and to manage configurations, statistic collection,
performance, and security.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ethernet Switching Technology
Ethernet Switching Technology dramatically boosted the total bandwidth of a
network, eliminated congestion problems inherent with CSMA/CD (Carrier Sense
multiple access with Collision Detection) protocol, and greatly reduced
unnecessary transmissions.
This revolutionized networking. First, by allowing two-way, simultaneous
transmissions over the same port (Full-duplex), that essentially doubled the
bandwidth. Second, by reducing the collision domain to a single switch-port, that
eliminated the need for carrier sensing. Third, by using the store-and-forward
technology’s approach of inspecting each packet to intercept corrupt or redundant
data, switching eliminated unnecessary transmission that slow the network. By
employing address learning, which replaced the inefficient receiving port.
Auto-negotiation regulates the speed and duplex of each port, based on the
capability of both devices. Flow-control allows transmission from a 100Mbps node
to a 10Mbps node without loss of data. Auto-negotiation and flow-control may
require disablement for some networking operations involves legacy equipment.
Disabling the auto-negotiation is accomplished by fixing the speed or duplex of a
port.
Ethernet Switching Technology supplied higher performance at costs lower than
other solutions. Wider bandwidth, no congestion, and the reduction in traffic is
why switching is replacing expensive routers and inefficient hubs as the ultimate
networking solution. Switching brought a whole new way of thinking to networking.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
2.
Hardware Description
Front Panel
The Front Panel of the MIL-SM2401M-STK switch series consists of 24
10/100Base-TX RJ-45 ports (Auto MDI/MDIX) and one expansion slot. The LED
Indicators and console port are also located on the front panel of the switch.
Console
Port
LED
Indicators
Fast Ethernet Ports
Module Bay
Figure 2-1. Front panel for MIL-SM2401M-STK
„
„
„
100BASE-TX UTP Ports: The MIL-SM2401M-STK comes with 24 100Mbps
Fast Ethernet UTP ports.
Modules: The MIL-SM2401M-STK provides a broad range of expansion slot
modules. Check with your MiLAN sales representative for details.
Console Port: Console management can be done through the Console Port.
It requires a direct connection between the switch and an end station (PC) via
a RS-232 cable.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
LED Indicators
The LED Indicators give real-time information of systematic operation status. The
following table provides descriptions of LED statuses and their meaning.
Figure 2-2. LED Indicators
LED
Status
Green
Off
Description
Power On
Power
Power is not connected
Green
Off
The port is in 100Mbps speed.
The port is in 10Mbps speed.
The port is connecting with the device.
The port is receiving or transmitting data.
No device attached.
100M
Green
LNK/ACT Blinks
Off
Orange
The port is operating in Full-duplex mode.
Collision of Packets is occurring on the port.
The port is operating in half-duplex mode
FDX/COL Blinks
Off
Table 2-1. The Description of LED Indicators
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Panel
The 3-pronged power plug is located at the rear panel of the MIL-SM2401M-STK
as shown in Figure 2-3. The Switch will work with AC in the range 100-240V AC,
50-60Hz.
Figure 2-3. The Rear Panel of the 24 10/100TX plus one Exp. Slot stackable switch
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Desktop Installation
Set the switch on a sufficiently large flat space with a power outlet nearby. The
surface where you put your switch should be clean, smooth, level and sturdy.
Provide enough clearance around the switch to allow attachment of cables, power
cord and allow air circulation.
Attaching Rubber Feet
A. Make sure the mounting surface on the bottom of the switch is grease and
dust free.
B. Remove adhesive backing from your Rubber Feet.
C. Apply the Rubber Feet to each corner on the bottom of the switch.
These footpads can prevent the switch from shock/vibration.
Figure 2-4. Attaching Rubber Feet to each corner on the bottom of the switch
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Rack-mounted Installation
The MIL-SM2401M-STK switch come with a rack-mounted kid and can be
mounted in an EIA standard size, 19-inch Rack. The switch can be placed in a
wiring closet with other equipment.
Perform the following steps to rack mount the switch:
A. Position one bracket to align with the holes on one side of the switch and
secure it with the smaller bracket screws. Then attach the remaining bracket
to the other side of the Switch.
Figure 2-5. Attach mounting brackets with screws
12
Download from Www.Somanuals.com. All Manuals Search And Download.
B. After attaching both mounting brackets, position the MIL-SM2401M-STK in
the rack by lining up the holes in the brackets with the appropriate holes on
the rack. Secure the switch to the rack with a screwdriver and the
rack-mounting screws.
Figure 2-6. Mount the switch in an EIA standard 19-inch Rack
Note: For proper ventilation, allow about at least 4 inches (10 cm) of clearance on the
front and 3.4 inches (8 cm) on the back of the Switch. This is especially important for
enclosed rack installation.
Power On
Connect the power cord to the power socket on the rear panel of the switch.
Connect the other end of the power cord to an appropriate power outlet. The
internal power supply of the switch works with voltage range of AC in the
100-240VAC, frequency 50~60Hz.
Press the power On/Off switch to the On position and check the power indicator
on the front panel to see if power is properly supplied.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
Network Application
This section provides you a few samples of network topology in which the Switch
is used. In general, the 24 10/100TX plus one Exp. Slot Single IP Stackable
Switch is designed as a segment switch. That is, with its large address table
(8000 MAC address) and high performance, it is ideal for interconnecting
networking segments.
PC, workstations, and servers can communicate each other by directly
connecting with 24 10/100TX plus one Exp. Slot Single IP Stackable Switch. The
switch automatically learns nodes address, which are subsequently used to filter
and forward all traffic based on the destination address.
By using Uplink port, the Switch can connect with another switch or hub to
interconnect other small-switched workgroups to form a larger switched network.
Meanwhile, you can also use fiber ports to connect switches. The distance
between two switches via fiber cable can be up to 2 kilometer (multi-mode fiber)
or 60 kilometer (single-mode fiber).
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Small Workgroup
The MIL-SM2401M-STK switch can be used as a standalone switch to which
personal computers, servers and printer servers are directly connected to form a
small workgroup.
Figure 3-1. Small Workgroup Application
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Segment Bridge
For enterprise networks where large data broadcasts are constantly processed,
this switch is an ideal solution for department users to connect to the corporate
backbone.
In the illustration below, two Ethernet switches with PCs, print servers, and local
servers attached, are both connected to the switch. All the devices in this network
can communicate with each other through the switch. Connecting servers to the
switch allows other users to access the data on server.
Figure 3-2 Department Bridge Application
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Stacking Workgroup
Up to eight (8) individual MIL-SM2401M-STK switches can be connected to form
a single logical unit using embedded stacking technology. The stack behaves as a
single switching unit that is manageable by a master switch elected from one of
the member switches.
The master switch serves as the control center for the stack and automatically
creates and updates all of the switching tables. The remaining member switches
act as forwarding processors and each switch in the stack is assigned to a single
workgroup ID. In addition, a working stack can accept new members or delete
old ones without service interruption or degraded performance.
No special tools, extra software, or expensive equipment is needed to form a
Stacking Workgroup. With the MIL-SM2401M-STK, management applications
represent the entire stack as a single device with simple point and click
management.
Figure 3-3. A stacking workgroup application
17
Download from Www.Somanuals.com. All Manuals Search And Download.
4.
Console Management
Connecting a Terminal or PC to the Console Port
Console management involves the administration of the switch via a direct
connection to the RS-232 console port. This port is a female DB-9 connector.
From the main menu of the console program, the user has access to manage the
functions of the switch.
Figure 4-1. Connecting the switch to a terminal via RS-232 cable
Use the supplied RS-232 cable to connect a terminal or PC to the console port.
The terminal or PC to be connected must support the terminal emulation program.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Communication Parameters
After the connection between Switch and PC is finished, turn on the PC and run a
terminal emulation program or Hyper Terminal to match the following default
characteristics of the console port:
Baud Rate: 9600 bps
Data Bits: 8
Parity: none
Stop Bit: 1
Control flow: None
Figure 4-2. The settings of communication parameters
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Console - Login
After you have entered the parameter settings, click
. When the blank screen
OK
appears, press the Enter Key to access the login screen. Type the user name and
password to login. The default user name is root; the default password is root.
Figure 4-3. Console login screen
1.The switch also provides a serial interface to manage and monitor the switch.
The user can follow the Console Port Information provided by the web to use
the Windows HyperTerminal program to link the switch.
2.Type the user name and password to login. The default user name is root; the
default password is
.
root
3.The timeout on the console port is 60 seconds. If no action is taken on the
console screen for one minute, the program reverts back to the logon screen
and a new login is necessary in order to continue.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
4.The switch is shipped with a default IP address of 192.168.1.77. The default
subnet mask is 255.255.255.0.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Console Management Options
The system supports two types of console management – CLI Command and
Menu Selection. After you login to the system, you will see a command prompt.
To enter the Menu Selection management interface, type “menu” at the command
prompt and you will see the main menu interface.
To enter CLI Command management interface, type “enable” at the command
prompt.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
5.
CLI Management Interface
To enter CLI Command management interface, type “
” at the command
enable
prompt. The following tables list the CLI commands and descriptions.
5-1. Commands Level
Access
Method
Exit
Modes
Prompt
About This Mode1
Method
The user commands
available at the user
level are a subset of
those available at the
privileged level.
Begin a
Enter logout
or quit.
User EXEC
session with
your switch.
Switch>
Use this mode to
• Perform basic tests.
• Display system
information.
The privileged
Enter the
command is advance
mode
enable
Enter
Privileged
EXEC
command
while in user
EXEC mode.
Switch#
disable to
exit.
Privileged this mode to
• Display advance
function status
• Save configures
Use this mode to
configure parameters
that apply to your
Enter the
configure
command
To exit to
privileged
EXEC
Global
Switch
Configuration
(config)#
23
Download from Www.Somanuals.com. All Manuals Search And Download.
while in
mode, enter switch as a whole.
exit or end
privileged
EXEC mode.
Enter the vlan
database
To exit to
Use this mode to
configure
VLAN
command
while in
Switch
(vlan)#
user EXEC
database
mode, enter VLAN-specific
privileged
EXEC mode.
exit.
parameters.
To exit to
global
Enter the
interface
command
(with a
configuratio
n mode,
Use this mode to
configure parameters
for the switch and
Ethernet ports.
Interface
switch
enter exit.
specific
configuration
(config-if)# To exist to
interface)
while in global
configuration
mode
privileged
EXEC
mode, or
end.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
5-2. Commands Set List
5-2-1. System Commands Set
Command
Commands
Description
Defaults
Example
Level
Global
system name
[systemname]
Set switch system
name string
Switch (config)#
system name xxx
configuration
mode
system location Global
Switch (config)#
system location
xxx
Set switch system
location string
[system
location]
configuration
mode
system
Global
Switch (config)#
system
description
[systemdescript
ion]
Set switch system
description string
configuration
mode
description xxx
Global
Switch (config)#
system contact
xxx
system contact
[systemcontact]
Set switch system
configuration
mode
contact window string
Use the ip address
interface configuration
command to set an IP
address for a switch.
Use the no form of this
command to remove
an IP address or to
disable IP processing.
Switch (config)#
ip address
ip address
Global
[ip-address]
[subnet-mask ]
[ gateway]
configuration
mode
192.168.1.1
255.255.255.0
192.168.1.254
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Global
Halt and perform a
cold restart
Switch (config)#
reload
reload
default
configuration
mode
Global
Switch (config)#
Default
configuration
mode
Restore to default
Global
Changes a login
username. (maximum
10 words)
username
Switch (config)#
username xxxxxx
configuration
mode
[user-name]
Global
Switch (config)#
Password xxxxxx
password
Specifies a password
(maximum 10 words)
configuration
mode
[password]
Switch> show
system info
Name: switch1
location: lab
Description:
layer2 switch
Contact:
show system
info
Show system
information
User EXEC
somewhere
Serial NO: 1.00
Switch# show ip
Address ip:
192.168.1.1
Address subnet:
255.255.255.0
Address
Privileged
EXEC
show ip
Show ip information
gateway:
192.168.1.254
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Switch# show
accounting
show
Privileged
EXEC
Show username &
password
accounting
Username: root
Password: root
Switch> show
version
Use the show version
user EXEC command
to display version
information for the
hardware and
Firmware
version: 1.0
Hardware
show version
User EXEC
version: 3.0
Kernel version:
1.10
firmware.
Switch (config)#
show terminal
Baud rate
Use the show terminal
command to display
console information
for the switch
(bits/sec): 9600
Data Bits: 8
Parity Check:
none
Privileged
EXEC
show terminal
Stop Bits: 1
Flow Control:
none
27
Download from Www.Somanuals.com. All Manuals Search And Download.
5-2-2. Port Commands Set
Command
Commands
Description
Defaults
Example
Level
Use the fast Ethernet
interface
Switch (config)#
interface
interface
configuration
command
fastEthernet 0/1
[FastEthernet
/module
Interface
configuration
mode
Use the module
Ethernet interface
configuration
command
Ethernet] [slot
id] [id]
Switch (config)#
interface
moduleEthernet 1/1
Use the duplex
configuration
Switch (config)#
interface
command to specify
the duplex mode of
operation for Fast
Ethernet.
Auto
fastEthernet 0/1
Switch (config-if)#
duplex full
Interface
configuration
mode
duplex [full | half|
auto]
Use the duplex
configuration
Switch (config)#
interface
command to specify
the duplex mode of
operation for module
Ethernet.
Auto
moduleEthernet 1/1
Switch (config-if)#
duplex full
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Use the speed
configuration
Switch (config)#
interface
speed
Interface
command to specify
the speed mode of
operation for Fast
Ethernet.
[10 | 100 | 1000 | configuration
Auto
fastEthernet 0/1
Switch (config-if)#
speed 10
auto]
mode
Use the speed
configuration
command to specify
the speed mode of
operation for module
Ethernet.
Switch (config)#
interface
Interface
configuration
mode
speed [10| 100 |
1000 | auto]
(The 100Base-FX
module only
fastEthernet 1/2
Switch (config-if)#
speed 1000
supported for speed
100)
(The 1000Base-FX
module only
supported for speed
1000 & auto)
Use the flow control
configuration
command on
Switch (config)#
interface
Ethernet ports to
control traffic rates
during congestion.
Use the no form of
this command to
disable security on
the port.
Interface
configuration
mode
flowcontrol on or
no flowcontrol
On
fastEthernet 0/1
Switch (config-if)#
flowcontrol on
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Use the security
configuration
Switch (config)#
interface
command on
Interface
configuration
mode
security on or no
security
Ethernet ports.
Use the no form of
this command to
disable security on
the port.
Disable
fastEthernet 0/1
Switch (config-if)#
security on
Use the priority
configuration
Switch (config)#
interface
command on
priority on [hi |
low] or no
priority
Interface
configuration
mode
Ethernet ports.
Use the no form of
this command to
disable security on
the port.
Disable
fastEthernet 0/1
Switch (config-if)#
priority on hi
Set bandwidth in or
out rate. The value
rage is (0~999), and
Switch (config)#
interface
Interface
Bandwidth [in |
out] [value]
configuration zero of the value is
Disable
fastEthernet 0/1
Switch (config-if)#
bandwidth in 50
mode
disable
(The module can’t be
setting)
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Use the state
interface
configuration
Switch (config)#
interface
command to specify
the state mode of
operation for
Interface
configuration
mode
State [Enable |
Disable]
Enable
fastEthernet 0/1
Switch (config-if)#
state disable
Ethernet ports. Use
the disable form of
this command to
disable the port.
Switch (config)#
interface
Interface
configuration
mode
show interface
configuration
show interface
fastEthernet 0/1
Switch (config-if)#
show interface
configuration
configuration status
Switch (config)#
interface
Interface
configuration
mode
show interface
status
show interface actual
status
fastEthernet 0/1
Switch (config-if)#
show interface
status
Switch (config)#
interface
Interface
configuration
mode
show interface
accounting
show interface
statistic counter
fastEthernet 0/1
Switch (config-if)#
show interface
accounting
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Switch (config)#
interface
Interface
show bandwidth configuration bandwidth of the
mode values
Display the
fastEthernet 0/1
Switch (config-if)#
Show bandwidth
32
Download from Www.Somanuals.com. All Manuals Search And Download.
5-2-3. Trunk Commands Set
Command
Commands
Description
Defaults
Example
Level
port group
[group-number]
[port-list] lacp
[on | off] workp
[work ports]
LACP:
Switch (config)# port
group 1 1-4
Add trunking
group.
Global
lacp on workp 2
Use the no form of
this command to
delete trunking
group.
configuration
mode
Disable
no port group
[group-number]
lacp [on | off]
workp [work
ports]
Trunk without LACP:
Switch (config)# port
group 1 1-4
lacp off workp 4
Switch # show group
1
Display trunk group
information. If there
is no group-number
in put, display all
trunk groups.
Group Trunk.1:
Ports: 02 03 04
Priority: 0001
Lacp: Enable
Work ports: 0
show group
[group-ID]
Privileged
EXEC mode
Switch (config)# port
group 3 activityport
2-4
port group
[group-number]
activityport
[port-list]
Global
Set trunking group
port active
configuration
mode
Trunk.1 Lacp:
Enable
Check OK!
NEW: 2 4
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Update finished!!
34
Download from Www.Somanuals.com. All Manuals Search And Download.
5-2-4. VLAN Commands Set
Command
Commands
Description
Defaults
Example
Level
To enter the VLAN
configuration
Switch# vlan
database
Privileged
Vlan datatbase
EXEC mode
interface
Switch(vlan)#
To set switch VLAN
mode .Use the no
form of this
vlanmode
[disable|
VLAN
Switch (vlan)#
database
mode
Disable
portbase|
vlanmode 802.1q
command to restore
to default.
802.1q | gvrp]
Port Base VLAN
vlan [Group
Name] grpid
[Group ID] port
[Port Number]
no vlan Group
Name] [Group
ID]
VLAN
Add new Port Base
VLAN
Switch (vlan)# vlan
v2 grpid 2 port 1-4
database
mode
VLAN
Delete port base
VLAN group
Switch (vlan)# no
vlan v2 2
database
mode
show vlan
Show VLAN of
Group Name or
Group ID
VLAN
[GroupName]
[GroupID] or
show vlan
Switch (vlan)# Show
vlan v2 2
database
mode
information
vlan [Group
name] add [port VLAN
Set the port of
Switch (vlan)# vlan
v2 add 5 tagged
Number]
database
some port group
tagged or untagged
[tagged |
mode
untagged]
vlan [Group
name] delete
VLAN
Remove the port
Switch (vlan)# vlan
v2 delete 5
database
from it’s port group.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
[port Number]
mode
802.1Q | 802.1Q with GVRP VLAN mode
Add new 802.1Q
VLAN
vlan [Group
name]
VLAN
[VLAN name]:
VLAN name
Switch(vlan)# vlan
v2 vlanid 2 port 1-4
tag 2-4
vlanid [Vlan ID]
port [port
database
mode
[VLAN ID]: 1 ~ 4094
[port ID]:
Number] tag
[port Number]
port members 1~9
Switch (vlan)# no
vlan v2
no vlan
VLAN
Delete 802.1Q
VLAN group
[Group name] or database
Switch (vlan)# no
vlan v2 2
[VLAN ID]
mode
Add protocol vlan
[Group name]: vlan
group name
[protocol value]
IP-ip , ARP-arp,
Appletalk_AARP-ap
p_arp ,
vlan protocol
[Group name]
[protocol value]
vlanid [VLAN ID]
port
VLAN
Novell_IPX-ipx ,
Banyan_vines-bany
an_c4,
Switch (vlan)# vlan
protocol v3 ip vlanid
2 port 5-8 tag 6,8
6510,652
6
database
mode
[portNumber]
tag [port
Banyan_vines-bany
an_c5,
Number]
Banyan_vines-bany
an_ad,
Decent_mop_01-de
cent_01,
Decent_mop_02-de
36
Download from Www.Somanuals.com. All Manuals Search And Download.
cent_02,
Decent_dpr-decent
_dpr,
Decent_LAT-decen
t_lat,
Decent_LAVC-dece
nt_larc, IBM
SNA-ibm, X.75
internet-x75, X.25
Layer3-x25
[VLAN ID]: 1 ~ 4094
[port Number]:
port Number 1~24
Set VLAN ID range
[1~255] range 0
[256~511] range 1
[512~767] range 2
[768~1023] range 3
[1024~1279] range
4
Switch (vlan)#
vlanidrange 2
[1280~1535] range
5
VLAN
vlanidrange
database
mode
[VLANidrange]
[1536~1791] range
6
OLD: 0
NEW: 2
[1792~2047] range
7
[2048~2303] range
8
[2304~2559] range
9
[2560~2815] range
37
Download from Www.Somanuals.com. All Manuals Search And Download.
10
[2816~3071] range
11
[3072~3327] range
12
[3328~3583] range
13
[3584~3839] range
14
[3840~4094] range
15
VLAN protocol
[Groupname]
add
VLAN
Set the port of
Switch (vlan)# vlan
protocol v2 add 5
tagged
database
mode
some port group
tagged or untagged
[portNumber]
[tagged |
untagged]
VLAN protocol
[Groupname]
delete
VLAN
Remove the port
Switch (vlan)# vlan
protocol v2 delete 5
database
mode
from its port group.
[portNumber]
Show VLAN of
Group Name or
VLAN ID
show vlan
VLAN
[Groupname]
[GroupID] or
show vlan
Switch (vlan)# show
vlan v2 2
database
mode
information
vlanid: 1 ~ 4094
show protocol vlan
Protocol
VLAN
show vlan
protocol
Switch (vlan)# show
vlan protocol
database
mode
ip
ipx
netbios
38
Download from Www.Somanuals.com. All Manuals Search And Download.
port [port ID]
pvid [port VID]
ingressfilter1
[on | off]
Set Port PVID and
Ingress Filter
VLAN
Switch (vlan)# port 2
pvid 2 ingressfilter1
off ingressfilter2 on
database
mode
Rules1 & Ingress
Filter Rules2
ingressfilter2
[on | off]
Switch (vlan)# show
port 2
show Port PVID
and Ingress Filter
Rules1 & Ingress
Filter Rules2
Port ID: 2
VLAN
show port [port
ID]
Port Vid: 2
Ingress 1 Filter:
Disable
database
mode
Ingress 2 Filter:
Enable
39
Download from Www.Somanuals.com. All Manuals Search And Download.
5-2-5. Spanning Tree Commands Set
Command
Commands
Description
Defaults Example
Level
Switch> show
spanning-tree
System:
Priority: 32768
Max Age: 20
Hello Time: 2
Forward Delay: 15
Priority: 32768
Mac Address:
004063800030
Root_Path_Cost: 0
Root Port: we are
root
Display a summary
of the spanning-tree
states.
show
User EXEC
mode
spanning-tree
Max Age: 20
Hello Time: 2
Forward Delay: 15
Use the
spanning-tree
global configuration
command to enable
spanning-tree
[on / off] or no
spanning-tree
Global
Switch (config)#
spanning-tree on
configuration Spanning Tree
mode Protocol (STP). Use
Disable
the no form of the
command to restore
to default
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Use the
spanning-tree
max-age global
configuration
command to
Global
Switch (config)#
spanning-tree priority
32767
spanning-tree
configuration change the priority. 32768
priority [number]
mode
Use the no form of
this command to
return to the default
interval.
Use the
spanning-tree
max-age global
configuration
command to
change the interval
between messages
the spanning tree
spanning-tree
max-age
Global
receives from the
Switch (config)#
spanning-tree
max-age 15
configuration root switch. If a
20 sec
[seconds]
mode
switch does not
receive a bridge
protocol
data unit (BPDU)
message from the
root switch within
this interval, it
recomputes the
Spanning Tree
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Protocol (STP)
topology. Use the
no form of this
command to return
to the default
interval.
Use the
spanning-tree
hello-time global
configuration
command to specify
the interval
spanning-tree
hello-time
Global
Switch (config)#
spanning-tree
hello-time 3
configuration between hello
mode bridge protocol data
2 sec.
[seconds]
units (BPDUs). Use
the no form of this
command to return
to the default
interval.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Use the
spanning-tree
forward-time global
configuration
command to set the
forwarding-time for
the specified
spanning-tree
instances. The
forwarding time
determines how
long each of the
listening and
spanning-tree
forward-time
[seconds]
Global
Switch (config)#
spanning-tree
forward-time 20
configuration
mode
15 sec.
learning states last
before the port
begins forwarding.
Use the no form of
this command to
return to the default
value.
Use the
spanning-tree cost
interface
configuration
10 Mbps Switch (config)#
Interface
command to set the
–
100
interface
stp-path-cost
[PortCost]
configuration path cost for
fastEthernet 0/2
mode
Spanning Tree
Protocol (STP)
calculations. In the
event of a loop,
spanning tree
100 Mbps Switch (config-if)#
– 10 stp-path-cost 20
43
Download from Www.Somanuals.com. All Manuals Search And Download.
considers the path
cost when selecting
an interface to
place into the
forwarding state.
Use the no form of
this command to
return to the default
value.
Use the
spanning-tree
port-priority
interface
configuration
Switch (config)#
interface
command to
Interface
configuration
mode
stp-path-priority
[Port Priority]
configure a port
priority that is used
when two switches
tie for position as
the root switch. Use
the no form of this
command to return
to the default value.
128
fastEthernet 0/2
Switch (config-if)#
stp-path-priority 127
44
Download from Www.Somanuals.com. All Manuals Search And Download.
5-2-6. QOS Commands Set
Command
Commands
Description
Defaults Example
Level
qos
Enable/Disable
broadcast storm
storm-control
[5|10|15|20|25|
off (%)] or no
storm-control
Global
Switch (config)#
configuration control. Use the no
OFF
qos storm-control 5
mode
form of this command
to restore to default.
qos
Enable/Disable low
priority delay board.
low-priority-dela
y-bound [on|off]
[sec.] or no qos
low-priority-dela
y-bound
Switch (config)#
qos
Global
configuration Use the no form of
Off
low-priority-delay-b
ound on 1
mode
this command to
restore to default.
WRR:
Switch (config)#
qos queuepolicy
wrr hi 7 low 1
[Policy]:fcfs: first in
and first out
wrr: weight round
robin
First Come First
Served:
qos queuepolicy
[Policy] hi
Global
WRR
Hi 2
configuration
mode
Switch (config)#
qos queuepolicy
fcfs
[Priority] low
[Priority]
sp: all high before
low.
Low 1
[Priority] Hi:1~7
Low:1
All High before
Low:
Switch (config)#
qos queuepolicy sp
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Global
Switch (config)#
qos level 2,3
enable
qos level
0~3 LOW
4~7 HI
configuration [Priority] 0~7
mode
[priority] enable
Global
no qos level
[priority]
0~3 LOW Switch (config)# no
configuration [Priority] 0~7
mode
4~7 HI
qos level 0-7
qos
Set qos bridge delay
bound
configuration Use the no form of
bridge-delay-bo
und [number] .
no qos
Switch (config)#
Global
qos
OFF
bridge-delay-bound
1
mode
this command to
restore to default.
bridge-delay-bo
und
Switch (config)#
show qos
Global
show qos
Show broadcast
storm control.
configuration
mode
storm-control
storm-control
QOS storm control
mode: ENABLE
Switch (config)#
show qos
show qos
Privileged
Show low priority
low-priority-delay-b
ound
low-priority-dela
y-bound
EXEC mode delay board.
Qos low priority
delay bound: 1
Switch (config)#
show qos policy
Qos Mode: WRR
Privileged
show qos policy
Show qos policy
EXEC mode
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Switch (config)#
show qos
show qos
bridge-delay-bo
und
Privileged
Show bridge delay
bridge-delay-bound
bridge-delay-bound
5
EXEC mode bound
47
Download from Www.Somanuals.com. All Manuals Search And Download.
5-2-7. IGMP Commands Set
Command
Commands
Description
Defaults
Example
Level
Global
Enable /Disable
Switch (config)#
igmp on
igmp [on | off]
configuration IGMP snooping
Off
mode
function
Igmp-query
[auto |enable |
disable]
Global
Modify IGMP query
mode
Switch (config)#
configuration
mode
Disable
Igmp-query enable
Switch# show ip
igmp profile
IP
show ip igmp
profile
Privileged
Displays the details of
EXEC mode an IGMP profile entry.
VID Port 224.1.1.1
10 1,2,6
48
Download from Www.Somanuals.com. All Manuals Search And Download.
5-2-8. Mac / Filter Table Commands Set
Command
Commands
Description
Defaults
Example
Level
Use the
(Enable)
mac-address-table
aging-time global
configuration
Switch (config)#
mac-address-table
aging-time on
mac-address-ta
ble aging-time
[on | off]
command to set the
length of time that a
dynamic entry
remains in the MAC
address table after
the entry is used or
updated.
Switch (config)#
mac-address-table
aging-time 333
Global
mac-address-ta
ble aging-time
[sec.]
configuration
mode
300 secs
(Disable)
Switch (config)#
mac-address-table
aging-time off
Or
or no
Use the no form of
this command to
use the default
aging-time interval.
The aging time
applies to all
mac-address-ta
ble aging-time
Switch(config)# no
mac-address-table
aging-time
VLANs.
Use the
mac-address-table
static to add static |
filter addresses to
the MAC address
table. Use the no
form of this
Switch (config)#
interface fastEthernet
0/2
mac-address-ta
ble table [static |
filter] hwaddr
[MAC address]
vlanid
Interface
configuration
mode
Switch (config-if)#
mac-address-table
static hwaddr
004063112233 vlanid
10
N/A
[VLAN-ID]
command to
remove static
entries from the
49
Download from Www.Somanuals.com. All Manuals Search And Download.
MAC address table.
Switch (config)#
interface fastEthernet
0/2
no
Use the no
mac-address-ta
ble [static | filter]
hwaddr [MAC
address] vlanid
[VLAN-ID]
mac-address-table
privileged EXEC
command to delete
entries from the
MAC address table.
Interface
configuration
mode
Switch (config-if)# no
mac-address-table
static hwaddr
004063112233 vlanid
10
Use the show
mac-address-table
user EXEC
Switch (config)#
show
show
Privileged
mac-address-ta
ble [static | filter]
EXEC mode command to display
the MAC address
mac-address-table
static
table.
Use the show
Switch (config)#
show
mac-address-table
show
Privileged
user EXEC
mac-address-table
aging-time 300
MAC Address
aging-time: 300
mac-address-ta
ble aging-time
EXEC mode command to display
the MAC address
table.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
5-2-9. SNMP Commands Set
Command
Commands
Description
Defaults
Example
Level
snmp
Global
Switch (config)#
snmp system-name
l2switch
Set Snmp agent
system name
system-name
[SystemName]
configuration
mode
N/A
snmp
Global
Switch (config)#
snmp
Set Snmp agent
system location
system-location
configuration
N/A
N/A
[SystemLocation] mode
system-location lab
snmp
Global
Switch (config)#
snmp system-contact
where
Set Snmp agent
system contact
system-contact
[SystemContact]
configuration
mode
snmp
Add snmp
community-strings
[Community]
right [RO | RW]
Or
community string.
Use the no form of
Switch (config)#
snmp
Global
PUBLIC
RO
configuration this command to
community-strings
public right RW
mode
remove the
specified
no snmp
community-strings
[Community]
community.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
5-2-10. Port Mirroring Commands Set
Command
Commands
Description
Defaults Example
Level
Use the port
monitor interface
configuration
command to
port monitor
[RX|TX|Both
|Disable]
enable Switch
Port Analyzer
Switch (config)#
Interface fastEthernet
0/8
Interface
configuration (SPAN) port
N/A
PortList
mode
monitoring on a
port. Use the no
form of this
Switch (config-if)# port
monitor both 3
Or
no port monitor
command to
return the port to
its default value.
Switch (config-if)#
show port monitor
State: ENABLE
AnalysisPortId: 8
Port 1 Rx: Monitor
Port 1 Rx: Monitor
Port 2 Rx:
Use the show port
monitor privileged
EXEC command
to display the
Interface
show port
monitor
configuration ports for which
Port 2 Rx:
mode
Switched Port
Analyzer (SPAN)
port monitoring is
enabled.
Port 3 Rx: Monitor
Port 3 Rx: Monitor
Port 4 Rx:
Port 4 Rx:
Port 5 Rx:
Port 5 Rx:
Port 6 Rx:
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Port 6 Rx:
Port 7 Rx:
Port 7 Rx:
Port 8 Rx: Analysis
Port 8 Tx: Analysis
Port 9 Rx:
Port 9 Rx:
53
Download from Www.Somanuals.com. All Manuals Search And Download.
5-2-11. Stacking Commands Set
Command
Commands
Description
Defaults
Example
Level
Switch>show stackinglist
show
Show IP
User EXEC
MAC = 00:22:33:44:55:66
[Master]
stackinglist
stacking List
No Slave!
Switch>show stackinginfo
00.22.33.44.55.66
Show
stackinginfo
[MAC
Show the stack
information
User EXEC
GroupID: 3000
address]
Stacking Mode: Disable
System Information: test
Switch>stacking
stacking
[MAC
00.22.33.44.55.66
Change to
User EXEC
stacking mode
address]
Switch(stacking-00.22.33.
44.55.66)#
Set the stack ID
and mode
ID range:
Switch(stacking-00.22.33.
44.55.66)# set idmode
3000 0
set idmode
[ID] [mode]
Stacking
Mode
0~65535
Mode: 0 =
Disable, 1 =
Master, 2 =
Slave
Setting GroupID: 3000,
stacking Mode = Disable
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Switch(stacking-00.22.33.
44.55.66)# set information
test
set
Set the
Stacking
Mode
information
[name]
information of
the Stack
Setting System
Information: test
55
Download from Www.Somanuals.com. All Manuals Search And Download.
5-2-12. 802.1x Commands Set
Command
Commands
Description
Defaults Example
Level
Display a summary of
the 802.1x properties
and also the port sates.
User EXEC
mode
Switch> show
show 8021x
8021x
Use the 802.1x global
configuration command
to enable 802.1x
Global
Switch (config)#
8021x on
8021x [on | off] configuration
mode
Disable
protocols. Use the no
form of the command to
restore to default
Use the 802.1x system
radius IP global
8021x system
radiusip
configuration command
to change the radius
Switch (config)#
8021x system
radiusip
[RadiusServerIP Global
]
configuration server IP.
mode
Or
192.168.1.1
no 8021x
system radiusip
Use the no form of this
command to return to
the default interval.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Use the 802.1x system
sharekey global
8021x system
sharekey
[Sharekey]
or
configuration command
to change the shared
Global
Switch (config)#
8021x system
configuration key value.
mode
no 8021x
system
sharekey 123456
Use the no form of this
sharekey
command to return to
the default interval.
Use the 802.1x misc
quiet period global
configuration command
to specify the quiet
period value of the
switch.
8021x misc
quietperiod
[quietperiod
value]
Global
Switch (config)#
8021x misc
configuration
mode
Or
quietperiod 10
no 8021x misc
quietperiod
Use the no form of this
command to return to
the default interval.
Use the 802.1x misc TX
period global
8021x misc
txperiod
configuration command
to set the TX period.
Global
Switch (config)#
8021x misc
txperiod 5
[TXPeriod value]
Or
configuration
mode
no 8021x
txperiod
Use the no form of this
command to return to
the default value.
8021x misc
supptimeout
[SEC]
Global
Set the period of time
Switch(config)#
8021x misc
configuration the switch wait for a
mode
supplicant response to
supptimeout 30
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Or
an EAP request.
no 8021x
supptimeout
8021x misc
servertimeout
[SEC]
Set the period of time
the switch wait for a
server response to an
authentication request.
Global
Switch(config)#
8021x misc
configuration
mode
Or
servertimeout 50
no 8021x
servertimeout
8021x misc
maxrequest
[Number]
Or
Set the number of
authentication that must
time-out before
Global
Switch(config)#
8021x misc
configuration
mode
authentication fails and
the authentication
session ends.
maxrequest 2
no 8021x
maxrequest
8021x misc
reauthperiod
[SEC]
Set the period of time
after which clients
connected must be
re-authenticated..
Global
Switch(config)#
8021x misc
configuration
mode
Or
reauthperiod 20
no 8021x
reauthperiod
Use the 802.1x port
state interface
configuration command
to set the state of the
selected port.
Switch (config)#
interface
8021x prostate
[reject | accept |
authorize |
Interface
configuration
mode
fastethernet 0/3
Switch (config-if)#
8021x portstate
accept
„ Reject: the specified
port is required to be
held in the
disable]
unauthorized state.
„
the specified
Accept:
58
Download from Www.Somanuals.com. All Manuals Search And Download.
port is required to be
held in the Authorized
state.
„ Authorized: the
specified port is set to
the Authorized or
Unauthorized state in
accordance with the
outcome of an
authentication
exchange between
the Supplicant and the
authentication server.
„ Disable: The
specified port is
required to be held in
the Authorized state.
5-2-13. TFTP Commands Set
Command
Level
Commands
Description
Defaults
Example
copy
flash:config.text Global
Switch (config)# copy
flash:config.text tftp
>192.168.1.1
Backup configure
file command
tftp [TFTP IP
address] [file
name]
configuration
mode
>backup.dat
59
Download from Www.Somanuals.com. All Manuals Search And Download.
tftp:config.text
flash
Switch(config)#
Tftp:config.text flash
>192.168.1.1
Global
Restore configure
file command
[TFTP IP
address] [file
name]
configuration
mode
>restore.dat
tftp:firmware
flash
Switch (config)#
Tftp:firmware flash
>192.168.1.1
Global
Update firmware
command
[TFTP IP
address]
[file name]
configuration
mode
>image.bin
60
Download from Www.Somanuals.com. All Manuals Search And Download.
6.
Console Menu Management
To enter the Menu Selection management interface, type “
” at the command
menu
prompt. The following sections show the menu interface screens and descriptions.
6-1. Main Menu
There are six items for selection as follows:
Bullets and Numbering
Formatted:
Show the status of the switch.
Status and Counters:
Switch Configuration: Menus to configure the switch.
Protocol Related Configuration: Configures the protocol features.
Restarts the system or resets switch to the
System Reset Configuration:
default configuration.
Save Configuration: Saves the system configuration.
Exits the menu line program.
Logout:
61
Download from Www.Somanuals.com. All Manuals Search And Download.
<Control Key>
The control keys listed below are provided in all menus:
Move the cursor to next item.
Tab:
Backspace: Move the cursor to previous item.
Enter: Selects item.
Toggle selected item to next configuration or changes the value.
Space:
Exits the current action mode.
Esc:
62
Download from Www.Somanuals.com. All Manuals Search And Download.
6-2. Status and Counters
In Status and Counters, you can view Port status, counters, and system
information.
Press the “Tab” or “Backspace” to choose an item, and press “Enter” key to
select item.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
6-2-1. Port Status
Type: Displays port connection speed.
Link: Displays the port's link status. When the port is connecting with the device
and working normally, the link status is “ ”. When the port has no link, the link
UP
status is “
”.
Down
State: A port that is enabled will be displayed as “Enable”. A port that is disabled
will be displayed as “Disable”.
Displays the state of Auto-negotiation as either "Auto" or "Fixed".
Negotiation:
Displays the port speed and duplex mode.
Speed / Duplex:
FC: Displays the flow control for the port as being either on or off.
Indicates if Back Pressure capability is enabled or disabled, only valid for
BP:
HDX mode of operation.
Bandwidth In/Out: Indicates the Ingress bandwidth rate limiting speed in
increments of 100 kbps, 0 indicates port is at full bandwidth in.
Indicates whether traffic received on this port is put into the high priority
Priority:
or low priority queue or do not care.
Security: Indicates whether or not source MAC address based traffic filtering is
64
Download from Www.Somanuals.com. All Manuals Search And Download.
enabled on the port.
Actions->
Press the
or key to choose action menu, and then press the
Tab Backspace
Enter key to select the item.
<Previous Page>: Displays previous page.
Displays next page.
<Next page>:
Exits the port status page, and returns to previous menu.
<Quit>:
65
Download from Www.Somanuals.com. All Manuals Search And Download.
6-2-2. Port Counters
The following information provides a view of the current status of the unit. Select
Refresh to view updated statistics or select Clear to reset all counters to 0.
Actions->
Press the Tab or Backspace key to choose action menu, and then press the
key to select item.
Enter
Updates statistics on all counters.
<Refresh>:
<Clear>: Sets all counters to 0.
<Previous Page>: Displays previous page.
Displays next page.
<Next page>:
<Quit>: Exits the port counters page, and returns to previous menu.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
6-2-3. System Information
Bullets and Numbering
Formatted:
Displays the name of the device.
System Name:
Displays where the device is located.
System Location:
System Description: Displays the device type.
Firmware Version: Displays the switch’s firmware version.
Displays the system kernel software version.
Kernel Version:
Displays the switch’s Hardware version.
Hardware Version:
Bullets and Numbering
Formatted:
MAC Address: The unique hardware address assigned by manufacturer.
Module Information: Displays the module type and description.
Actions->
<Quit>: Exits the system information page, and returns to previous menu.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
6-3. Switch Configuration
In Switch Configuration, there are 8 main functions – Administration, Port, Trunk,
Port Mirroring, VLAN, Priority, MAC Address, and Misc. Configuration.
Press the Tab or Backspace key to choose action menu, and then press the
key to select item.
Enter
68
Download from Www.Somanuals.com. All Manuals Search And Download.
6-3-1. Administration Configuration
In Administration Configuration, you can configure system parameters, IP,
username and password.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
6-3-1-1. Device Information
Bullets and Numbering
Formatted:
Bullets and Numbering
Formatted:
10 characters can be used to give the switch a unique name in order to
Name:
distinguish it on the network. After configuration this name will show at the top
of each menu screen.
32 characters can be used to describe the switch.
Description:
Location: 32 characters can be used to give a location of the switch.
Contact: 32 characters can be used to indicate the contact person or
information.
Actions->
<Edit>: Configures all items. When finished, pressing ESC returns to the action
menu line.
Saves all configured value.
<Save>:
<Quit>: Exits the device information page and returns to previous menu.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
6-3-1-2. IP Configuration
This menu enables the user to change the default settings of the IP address,
subnet mask and gateway. Rebooting the switch is necessary to have the
configuration change take affect.
Bullets and Numbering
Formatted:
Disables or enables the DHCP client function.
DHCP:
Assign the switch IP address. The default IP is 192.168.1.77.
IP Address:
Subnet Mask: Assigns the switch IP subnet mask.
Gateway: Assigns the switch gateway. The default value is 192.168.16.254.
Actions->
<Edit>: Configures all items. When finished, pressing ESC returns to the action
menu line.
Saves all configured values.
<Save>:
<Quit>: Exits the IP configuration page and returns to previous menu.
Rebooting the switch is necessary to have the configuration change take
Note:
effect.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
6-3-1-3. User Name Configuration
Use this screen to change the User Name. The default user name is root.
Actions->
<Edit>: Configures all items. When finished, pressing ESC returns to the action
menu line.
Saves all configured values.
<Save>:
<Quit>: Exits the user name configuration page and returns to previous menu.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
6-3-1-4. Password Configuration
Use this screen to change the Password. The default password is root.
Actions->
<Edit>: Configures all items. When finished, pressing ESC returns to the action
menu line.
Saves all configured values.
<Save>:
<Quit>: Exits the password configuration page and returns to previous menu.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
6-3-2. Port Configuration
This page can change every port status.
Press the
key to select each item and press the
key to change the
SPACE
TAB
configuration of each item.
Displays current port status. The port can be set to disable or enable
State:
mode. If the port setting is set to disable, the port will not receive or transmit any
packets.
Negotiation: Displays current auto negotiation setting status of each port.
Speed/Duplex: Each port can be set for link speed and duplex mode.
User can set flow control function to enable or disable. FC (Flow
FC / BP:
control for full duplex link mode), BP (Backpressure for half duplex mode).
Bandwidth In/ Out: User can determine packet transmission rate control for
each port. Per level is 100Kbps. Individual control method of TX and RX is
supported.
Priority: User cab set each port to high or low priority.
Security: User can enable or disable port security function.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Actions->
Configures all items. When finished, pressing
returns to the action
ESC
<Edit>:
menu line.
<Save>: Saves all configured values.
<Previous Page>: Displays previous page.
Displays next page.
<Next page>:
Exits the port configuration page and returns to previous menu.
<Quit>:
76
Download from Www.Somanuals.com. All Manuals Search And Download.
6-3-3. Trunk Configuration
This page can configure trunk groups.
Press the
key to select each item and press the
key to change the
SPACE
TAB
configuration of each item.
Actions->
Configures all items. When finished, pressing
returns to the action
ESC
<Edit>:
menu line.
<Save>: Saves all configured values.
Exits the trunk configuration page and returns to previous menu.
<Quit>:
77
Download from Www.Somanuals.com. All Manuals Search And Download.
6-3-4. Port Mirroring Configuration
Port mirroring is a method for monitoring traffic in switched networks. Traffic
through ports can be monitored by one specific port. The traffic being received
or transmitted by the monitored ports will be duplicated into the monitoring port.
Press the Space key to change the configuration of an item.
Mirroring state: User can select Mirror mode for TX packet only, RX packet
only or Both.
The port to which all traffic to be mirrored will be sent.
Analysis port:
Press the SPACE key to mark each of the ports that should be mirrored.
Actions->
<Quit>: Exits the port mirroring configuration page and returns to previous
menu.
Configures all items. When finished, pressing
returns to the action
ESC
<Edit>:
menu line.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
<Save>: Saves all configured values.
79
Download from Www.Somanuals.com. All Manuals Search And Download.
6-3-5. VLAN Configuration
This page can set VLAN mode to port-based VLAN, 802.1Q VLAN or disable
VLAN function.
All ports are automatically placed in VLAN 1, the default VLAN. To create new
VLANs, use the Create a VLAN Group menu and add a VLAN. Make sure
when you enter a VLAN name you do not leave spaces. For example VLAN2
is correct; VLAN 2 will give an error. The VLAN name can be any 15
alphanumeric characters. Special characters are not allowed.
When changes are made to the VLAN mode, it is recommended that the
NOTE:
device be rebooted to ensure system integrity.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
6-3-5-1. VLAN Configure
Choose a VLAN
In the VLAN Configure menu select the type of VLAN you want to configure:
VLAN Disabled (default), Port Based VLAN, or IRRR802.1Q Tag based VLAN.
Save the configuration. There are 3 different options for VLANs to choose
from using the space bar: Disabled, Port Based and 802.1Q.
To configure a new VLAN, select Edit and then use the tab key to select items
you want to configure. The space bar allows you to select the different
options.
After adding a VLAN group, the configuration option Edit a VLAN Group will
allow you to change the membership by adding or deleting ports.
Port Based VLANs
These VLANs only apply to this switch. The VLANs can be overlapping,
meaning that any port can belong to more than one VLAN. One configuration
that is common for port based VLANs is to have all the ports on the switch on
separate VLANs except for the port that has the server connected. The port
connected to the server belongs to all the VLANs. This enables security
between ports but allows all ports access to the server. Up to 256 different port
based VLANs may be configured.
IEEE802.1Q VLANs
If IEEE802.1Q VLANs is selected, all the ports will belong to the default VLAN
1.
81
Download from Www.Somanuals.com. All Manuals Search And Download.
If more than one VLAN is necessary, the additional VLANs may be created.
Security VLANs
Security VLAN’s allow for limiting telnet, SNMP and web access to the switch to
a specific VLAN. The VID of the Security VLAN may be changed from 255 to
another value after creating the VLAN. The new VID must not already exist on
the box.
Set the port VLAN ID that will be assigned to untagged traffic
PVID (Port VID):
on a given port. This feature is useful for accommodating devices that you want
to participate in the VLAN, but don’t support tagging. Only one untagged VLAN
is allowed per port. Other VLANs need to be tagged.
Ingress Filter 1: If this is set, the port will only forward packets with VID (VLAN
ID) matching this port’s configured VID. Press the Space key to choose forward
or drop the frame with the VID not matching this port’s configured VID.
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Ingress Filter 2: Drop untagged frame. Press the Space key to choose drop or
forward the untagged frame.
Actions->
<Edit>: Configures all items. When finished, pressing ESC returns to the action
menu line.
Saves all configured values.
<Save>:
<Previous Page>: Displays previous page.
<Next page>: Displays next page.
Exits this page and returns to previous menu.
<Quit>:
83
Download from Www.Somanuals.com. All Manuals Search And Download.
6-3-5-2. Create a VLAN Group
Create Port-Based VLAN
Select <Edit> to create a port-based VLAN and add member/nonmember ports
to it.
1.VLAN Name: Type a name for the new VLAN using 15 alphanumeric
characters and no spaces.
2.
3.
Type the VLAN group ID. The group ID range is 1~4096.
Group ID:
Member:
Press the
key to choose VLAN member type.
Space
There are two selections:
Member: The port is member port.
NO: The port is NOT member port.
to return to the action menu line.
4.Press
“ESC”
5.Select <Save> to save all configured values.
If the trunk groups exist, it will be displayed (ex: TRK1, TRK2…) after
NOTE:
port26. The user can configure select if it is the member of the VLAN or not.
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Create 802.1Q VLAN
Select
to create a 802.1Q VLAN and add tagged /untagged member
<Edit>
ports to it.
1.
Type a name for the new VLAN using 15 alphanumeric
VLAN Name:
characters and no spaces.
2.VLAN ID: Type a VID (between 1~4096). The default is 1. There are 256
VLAN groups provided to configure.
3.
4.
Press the
key to choose the protocol type.
Protocol VLAN:
Member:
Space
Press the
key to choose the VLAN member. There are
Space
three selections:
UnTagged: This port is the member port of this VLAN group and
outgoing frames are NO VLAN-Tagged frames.
Tagged: This port is the member port of this VLAN group and
outgoing frames are VLAN-Tagged frames.
NO: The port is NOT member of this VLAN group.
5.Press
to return to the action menu line.
“ESC”
6.Select <Save> to save all configured values.
NOTE: If the trunk groups exist, it will be displayed (ex: TRK1, TRK2…) after
port26. The user can configure select if it is the member of the VLAN or not.
Actions->
<Edit>: Configures all items. When finished, pressing ESC returns to the action
menu line.
<Save>: Saves all configured values.
<Previous Page>: Displays previous page.
Displays next page.
<Next page>:
85
Download from Www.Somanuals.com. All Manuals Search And Download.
<Quit>: Exits this page and returns to previous menu.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
6-3-5-3. Edit / Delete VLAN Group
Use this menu to edit or delete a VLAN group.
When editing the chosen VLAN, the user can change the protocol VLAN or a
member port. A new protocol can be configured and the ports can be changed
to tagged or untagged or deleted as member ports from this VLAN. In edit
mode the VLAN Name and VLAN ID are read-only and cannot be modified.
VLAN1, the default VLAN, can never be deleted.
1.Press
or item.
<Edit> <Delete>
2.Choose the VLAN group to edit or delete by using the TAB key, and then
press Enter.
3.User can change the protocol VLAN or a member port.
4.After editing or deleting a VLAN, press the
values.
key to save all configured
<Save>
The VLAN Name and VLAN ID cannot be modified. The default VLAN
NOTE:
cannot be deleted.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Actions->
Configures all items. When finished, pressing
returns to the action
ESC
<Edit>:
menu line.
<Delete>: Deletes selected VLAN Groups.
<Previous Page>: Displays previous page.
Displays next page.
<Next page>:
Exits this page and returns to previous menu.
<Quit>:
88
Download from Www.Somanuals.com. All Manuals Search And Download.
6-3-5-4. Group Sorted Mode
Use this menu to select the VLAN groups sorted mode. There are two
selections:
Sorted by name
Name:
VID: Sorted by VID
The results can be viewed on the Edit/Delete a VLAN Group screen.
Actions->
Configures all items. When finished, pressing
returns to the action
ESC
<Edit>:
menu line.
<Save>: Saves all configured values.
89
Download from Www.Somanuals.com. All Manuals Search And Download.
<Quit>: Exits this page and returns to previous menu.
90
Download from Www.Somanuals.com. All Manuals Search And Download.
6-3-6. Priority Configuration
Level (0-7): There are eight (0 to 7) priority levels that can be mapped as high
or low priority queues.
User can select the ratio of high priority packets and low priority
QoS Mode:
packets by pressing the Space key.
1:1, 2:1, 3:1, 4:1, 5:1, 6:1, 7:1, FIFO, HÎL
High Low Queue service ratio:
The sequence of packets sent depends on arrival
First In First Out (FIFO):
order.
High to Low (HÎL): The high priority packets are sent before the low priority
packets.
(1:1, 2:1, 3:1, 4:1, 5:1, 6:1, 7:1): Select the preference given to packets in
Ratio
the switch's high-priority queue. These options represent the number of high
priority packets sent before one low priority packet is sent.
Actions->
Configures all items. When finished, pressing
returns to the action
ESC
<Edit>:
menu line.
Saves all configured values.
<Save>:
91
Download from Www.Somanuals.com. All Manuals Search And Download.
<Quit>: Exits this page and returns to previous menu.
6-3-7. MAC Address Configuration
92
Download from Www.Somanuals.com. All Manuals Search And Download.
6-3-7-1. Static MAC Address
When a static MAC address is added, it remains in the switch's address table,
regardless of whether the device is physically connected to the switch. This
saves the switch from having to re-learn a device's MAC address when the
device is disconnected or powered-off and then becomes active again.
The menu shows the current configured static MAC addresses. The user can
add, modify or delete a static MAC address. Once added, the MAC address
will be listed on this page.
Add static MAC address
1.Press the <Add> key. Then press the <Edit> key on this menu to add a
static MAC address.
2.Enter the MAC address to and from which the port should permanently
forward traffic, regardless of the devices network activity.
3.In the Port num field, enter the port number for the device.
4.If tag-based (802.1Q) VLANs are configured, the static addresses are
associated with individual VLANs. Enter the VID to associate with the MAC
93
Download from Www.Somanuals.com. All Manuals Search And Download.
address.
5.Press
to go back action menu line, and then select
to save all
<Save>
ESC
configured values.
Edit static MAC address
1.Press
key to modify a static MAC address.
<Edit>
2.Choose the MAC address that you want to modify and then press enter.
3.Press the <Edit> key to modify all the items.
4.Press
to go back action menu line, and then select
to save all
<Save>
ESC
configured values.
Delete static MAC address
1.Press the
key to delete a static MAC address.
<Delete>
2.Choose the MAC address that you want to delete and then press enter.
3.After delete static MAC address, you must press <Save> to complete the
deletion.
Actions->
<Add>: Adds a static MAC address.
Configures all items. When finished, pressing
returns to the action
ESC
<Edit>:
menu line.
<Delete>: Deletes selected static MAC addresses.
Displays previous page.
<Previous Page>:
Displays next page.
<Next page>:
<Quit>: Exits this page and returns to previous menu.
94
Download from Www.Somanuals.com. All Manuals Search And Download.
6-3-7-2. Filtering MAC Address
Add Filtering MAC address
1.Press the
key to add a static Filtering address.
<Add>
2.Press the <Edit> key to enter the MAC address you want to filter.
3.Enter the MAC address and then press enter.
4.Press the
key to modify all the items.
<Save>
5.
Press ESC to go back action menu line, and then select <Save> to save all
configured values.
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Edit Filtering MAC address
1. Press the <Edit> key to modify a static Filtering address.
2. Choose the MAC address that you want to modify and then press enter.
3. Press the <Edit> key to modify all the items.
4. Press ESC to go back action menu line, and then select <Save> to save all
configured values.
Delete Filtering MAC address
1.Press the
key to delete a Filtering MAC address.
<Delete>
2.Choose the MAC address that you want to delete and then press enter.
3.After delete Filtering MAC address, you must press <Save> to complete the
deletion.
Actions->
<Add>: Adds a static filtering address.
<Edit>: Configures all items. When finished, pressing ESC returns to the action
menu line.
<Delete>: Deletes selected static filtering addresses.
96
Download from Www.Somanuals.com. All Manuals Search And Download.
<Previous Page>: Displays previous page.
Displays next page.
<Next page>:
Exits this page and returns to previous menu.
<Quit>:
97
Download from Www.Somanuals.com. All Manuals Search And Download.
6-3-8. Miscellaneous Configuration
Switch parameters and stacking functions can be configured using the
miscellaneous configuration screens. The stacking function allows you to
centralize control of the switch in the network.
Actions->
Configures all items. When finished, pressing
returns to the action
ESC
<Edit>:
menu line.
<Save>: Saves all configured values.
Exits this page and returns to previous menu.
<Quit>:
6-3-8-1. MAC Address Ageing Time
To configure a different MAC Address Ageing Time, type the number of
seconds that an inactive MAC address remains in the switch’s address table
before it is deleted. Once the address is removed from the table, a device will
98
Download from Www.Somanuals.com. All Manuals Search And Download.
have to send out broadcast packets to be relearned by the switch and have its
address put in the table. The valid range is 300 to765 seconds. Default is 300
seconds.
6-3-8-2. Broadcast Storm Filtering
Broadcast storm filtering is used to limit the amount of broadcast traffic on the
network. An excessive amount of broadcast traffic can inhibit data packets
from timely delivery.
The valid threshold values are 5%, 10%, 15%, 20%, 25% and N/A. If the
broadcast traffic is greater than the configured value, broadcast packets will be
dropped. The default is N/A. The default is set so that no broadcast packets
are ever dropped no matter how many broadcast packets there are on the
network.
6-3-8-3. Max Bridge Transmit Delay Bound
Limits the packets queuing
Max bridge transmit delay bound (0,1-4 sec):
time in the switch. If enabled, the packets exceeding the queuing time will be
dropped. Press the Space key to set the time. Valid values are 1sec, 2sec, 4sec
and OFF. The default is 1 second when this feature is enabled. This setting
does not depend on what values are set in the “Priority Configuration” menu.
Low Queue Delay Bound: If this parameter is enabled, the “Max bridge
transmit delay bound” must also be configured. This item allows you to limit
queuing time of the low priority packets in the switch. When the low priority
packets exceed the “Max Delay Time” they will be transmitted. Press the Space
key to enable or disable this function. By default the Enable Delay Bound is set
to OFF.
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Set the time that low priority packets are queued
Low Queue Max Delay Time:
in the switch. The valid range is 0 to 255 ms. Since the default is OFF, the Max
Delay Time is 0. This item must be set if “Low Queue Delay Bound” is
enabled.
“Max bridge transmit delay bound control” must be enabled before Low
NOTE:
Queue Max Delay Bound is enabled.
6-3-8-4. Collision Retry Forever
User can choose to disable collision retry forever and, if a
Collisions Retry Forever:
collision occurs in half-duplex mode, the switch will attempt to send the packet 48
times and then drop the frame. When enabled, a collision that occurs in half-duplex
mode will result in repeated attempts by the switch forever.
6-3-8-5. Hash Algorithm
This Hash Algorithm is for hardware maintenance on the MAC table calculation.
This field should only be changed if an excessive amount of MAC address table
collisions are seen. It changes the hashing algorithm for storing new MAC
addresses in local memory.
6-3-8-6. IFG Compensation
Disable or Enable
IFG compensation:
Provides the ability to compensate for shorter inter-frame gaps during rate
limiting. It is recommended that this selection remain disabled.
6-3-8-7. IP Stacking Group ID (0…65535)
Assign a stacking group ID for the switch by entering a value between 0 and
100
Download from Www.Somanuals.com. All Manuals Search And Download.
65535. The switches must be assigned the same stacking group ID to be
stacked as a group.
6-3-8-8. IP Stacking Mode
Select one of the 3 modes to enable or disable the stacking function. To
configure the switch in the stacking group, use the Web GUI configuration
interface.
The stacking function is not enabled.
Disable:
Master: One switch must be selected to control all other switches in stacking
group. Only one switch can be assigned to be the master switch in one stacking
group. Once the stacking group is set up, the master switch will control all
switches in the stacking group.
Slave: All remaining switches in a stacking group must be configured to slave
mode. Once the stacking group is set up, the slave switches can only be
configured through the master switch.
Note:
1. Before configuring the stacking function, make sure all stack switches are in
the same network.
2. To configure the stacking function, enable the master switch first.
3. After you have configured the stacking function, use Cat. 5 cable to connect
every switch in the stacking group.
4. To remove the master switch from stacking group, the slave switches must
be removed first. When all slave switches are removed, the master switch
can be removed from the stacking group.
101
Download from Www.Somanuals.com. All Manuals Search And Download.
102
Download from Www.Somanuals.com. All Manuals Search And Download.
6-4. Protocol Related Configuration
6-4-1. STP
Spanning tree is a link management protocol that provides path redundancy
while preventing undesirable loops in the network.
103
Download from Www.Somanuals.com. All Manuals Search And Download.
6-4-1-1. STP Setup
This page enables or disables the Spanning Tree function. The Spanning
Tree function must be enabled before the STP function can be configured.
Actions->
<Edit>: Configures all items. When finished, pressing ESC returns to the action
menu line.
<Save>: Saves all configured values.
<Quit>: Exits this page and returns to previous menu.
104
Download from Www.Somanuals.com. All Manuals Search And Download.
6-4-1-2. System Configuration
All devices in the spanning tree instance will utilize the same values as the root
bridge to ensure consistency throughout the network. If this device becomes
the root bridge, then the other switches in the STP instance will utilize its values.
Spanning tree information for the Root Bridge on the left is for display only.
Configure new values for the STP parameter on the right.
You must enable STP function before selecting the configuration menu.
Priority: The value used to identify the root bridge. The bridge with the lowest
value has the highest priority and is selected as the root. Enter a number 1
through 65535.
The number of seconds a bridge waits without receiving
Max Age:
Spanning-Tree Protocol configuration messages before attempting a
reconfiguration. Enter a number 6 through 40.
105
Download from Www.Somanuals.com. All Manuals Search And Download.
The number of seconds between the transmission of
Hello Time:
Spanning-Tree Protocol configuration messages. Enter a number 1 through 10.
Forward Delay Time: The number of seconds a port waits before changing
from its Spanning-Tree Protocol learning and listening states to the forwarding
state. Enter a number 4 through 30.
Actions->
Configures all items. When finished, pressing
returns to the action
ESC
<Edit>:
menu line.
<Save>: Saves all configured values.
<Quit>: Exits this page and returns to previous menu.
106
Download from Www.Somanuals.com. All Manuals Search And Download.
6-4-1-3. STP Per Port Setting
State: Spanning tree status for each port is either forwarding or blocking.
PathCost: Specifies the path cost of the port that the switch uses to determine
which ports are the forwarding ports. If you change the value, you need to
restart the switch for valid value change to take effect.
Priority: Specifies the path cost of the port that the switch uses to determine
which ports are the forwarding ports. The lowest number is picked as the
forwarding port. The range is 1-65535 and the default value is based on
IEEE802.1D standard.
The values should be in the range:
10Mb/s = 50-600
100Mb/s = 10-60.
If you change the value, you must reboot the switch to save the value change.
On the action menu line press <Next Page> to configure Port 9 through Port 26
or press <Previous Page> returns to last page.
107
Download from Www.Somanuals.com. All Manuals Search And Download.
Actions->
Configures all items. When finished, pressing
returns to the action
ESC
<Edit>:
menu line.
<Save>: Saves all configured values.
Displays the previous page.
<Previous Page>:
Displays the next page.
<Next Page>:
<Quit>: Exits this page and returns to previous menu.
108
Download from Www.Somanuals.com. All Manuals Search And Download.
6-4-2. SNMP
Any Network Management station running the Simple Network Management
Protocol (SNMP) can manage the switch provided that the Management
Information Base (MIB) is installed. SNMP is a protocol that governs the transfer
of information between management and agent. The switch supports SNMP V1.
Use this menu to define management stations as trap managers and to enter
SNMP community strings. Users can also define a name, location, and contact
person for the switch.
109
Download from Www.Somanuals.com. All Manuals Search And Download.
6-4-2-1. SNMP System Options
Press
to enter all items,
to return to the action menu, and then
ESC
<Edit>
press <Save> to save the configured values.
Enter a name to identify the switch.
System Name:
Enter the name of the contact person or organization.
System Contact:
System Location: Enter the location of the switch.
Actions->
Configures all items. When finished, pressing
returns to the action
ESC
<Edit>:
menu line.
<Save>: Saves all configured values.
<Quit>: Exits this page and returns to previous menu.
110
Download from Www.Somanuals.com. All Manuals Search And Download.
6-4-2-2. Community Strings
Community strings serve as passwords and can be entered as one of the
following
:
Community Name: Enter the name of current community strings. The default is
“public”.
Write Access: Enables the permissions for Read Only or Read/Write.
Read only: Enables requests accompanied by this string to display
MIB-object information.
Read Write: Enables requests accompanied by this string to display
MIB-object information and to set MIB objects.
Add Community Strings
1.Press the
key. Then press the
key on this menu to add a
<Edit>
<Add>
SNMP Trap Manager.
2.Enter the Community Name and select the Write Access setting for the
Community String.
111
Download from Www.Somanuals.com. All Manuals Search And Download.
3.Press ESC to go back action menu line, and then select <Save> to save all
configured values.
Edit Community Strings
1.Press <Edit> key to modify a Community String.
2.Choose the Community Name that you want to modify and then press enter.
3.Enter the correct Community Name and Write Access setting.
4.Press ESC to go back action menu line, and then select <Save> to save all
configured values.
Delete Community Strings
1.Press the <Delete> key to delete a Community String.
2.Choose the Community Name that you want to delete and then press enter.
3.After deleting the Community String, you must press
deletion.
to complete the
<Save>
Actions->
Creates a trap manager.
<Add>:
112
Download from Www.Somanuals.com. All Manuals Search And Download.
<Edit>: Configures all items. When finished, pressing ESC returns to the action
menu line.
Deletes a community string. After deleting, press
to
<Save>
<Delete>:
complete the deletion.
<Save>: Saves all configured values.
Exits this page and returns to previous menu.
<Quit>:
113
Download from Www.Somanuals.com. All Manuals Search And Download.
6-4-2-3. Trap Managers
A trap manager is a management station that receives traps. The switch
generates system alerts. If no trap manager is defined, no traps are issued.
Create a trap manager by entering the IP address of the station and a community
string.
114
Download from Www.Somanuals.com. All Manuals Search And Download.
Add SNMP Trap Managers
1. Press the key. Then press the
key on this menu to add a
<Edit>
<Add>
SNMP Trap Manager.
2.Enter the IP address and Community Name for the SNMP Trap Manager.
3.Press ESC to go back action menu line, and then select <Save> to save all
configured values.
Edit SNMP Trap Managers
1. Press <Edit> key to modify a SNMP Trap Manager.
2.Choose the IP address and Community Name that you want to modify and
then press enter.
3.Enter the correct IP Address and Community Name.
4.Press ESC to go back action menu line, and then select <Save> to save all
configured values.
115
Download from Www.Somanuals.com. All Manuals Search And Download.
Delete SNMP Trap Managers
1. Press the key to delete a SNMP Trap Manager.
<Delete>
2.Choose the IP Address and Community Name that you want to delete and
then press enter.
3.After deleting the SNMP Trap Manager, you must press <Save> to complete
the deletion.
Actions->
Creates a trap manager.
<Add>:
<Edit>:
Configures all items. When finished, pressing
returns to the action
ESC
menu line.
<Delete>: Deletes a trap manager. After deleting, press <Save> to complete
the deletion.
<Save>: Saves all configured values.
<Quit>: Exits this page and returns to previous menu.
116
Download from Www.Somanuals.com. All Manuals Search And Download.
6-4-3. LACP
The Link Aggregation Control Protocol (LACP) provides a standardized means
for exchanging information between Partner Systems on a link to allow their
Link Aggregation Control instances to reach agreement on the identity of the
Link Aggregation Group to which the link belongs. Move the link to that Link
Aggregation Group, and enable its transmission and reception functions in an
orderly manner. Link aggregation lets you group up to eight consecutive ports
into a single dedicated connection. This feature can expand bandwidth to a
device on the network. LACP operation requires full-duplex mode. For
more information, please refer to IEEE 802.3ad.
117
Download from Www.Somanuals.com. All Manuals Search And Download.
6-4-3-1. LACP Working Ports
Displays the trunk group ID.
Group:
LACP: Press the Space key to enable or disable LACP (Link Aggregation
Control Protocol) support. If enabled, the group is an LACP static trunking group.
If disabled, the group is a local static trunking group.
The maximum number of ports that can be aggregated
LACP Work Port Num:
at the same time. If the group is an LACP static trunking group, the exceed
ports is standby and able to aggregate if the work ports fail. If the group is a
local static trunking group, the number must be the same as group ports.
NOTE: Before setting LACP support, you must first set the trunk group using
the Port / Trunk Configuration screen.
Actions->
Configures all items. When finished, pressing
returns to the action
ESC
<Edit>:
menu line.
<Save>: Saves all configured values.
Exits this page and returns to previous menu.
<Quit>:
118
Download from Www.Somanuals.com. All Manuals Search And Download.
6-4-3-2. LACP State Activity
Active: The port automatically sends LACP protocol packets.
Passive: The port does not automatically send LACP protocol packets, and
responds only if it receives LACP protocol packets from the opposite device.
Actions->
<Edit>: Configures all items. When finished, pressing ESC returns to the action
menu line.
<Save>: Saves all configured values.
<Quit>: Exits this page and returns to previous menu.
119
Download from Www.Somanuals.com. All Manuals Search And Download.
6-4-3-3. Group Status
When setting a trunking group, the relationship status information may be seen
on the LACP Group Status screen.
Actions->
<Previous Page>: Displays previous page.
Displays next page.
<Next page>:
<Quit>: Exits this page and returns to previous menu.
120
Download from Www.Somanuals.com. All Manuals Search And Download.
6-4-4. IGMP/GVRP Configuration
Use the IGMP/GVRP Configuration screen to enable or disable IGMP, Query
Mode and GVRP (GARP VLAN Registration Protocol) support.
Press the Space key to choose Enabled or Disabled.
Actions->
Configures all items. When finished, pressing
returns to the action
ESC
<Edit>:
menu line.
<Save>: Saves all configured values.
<Quit>: Exits this page and returns to previous menu.
121
Download from Www.Somanuals.com. All Manuals Search And Download.
6-4-5. 802.1x Configuration
122
Download from Www.Somanuals.com. All Manuals Search And Download.
6-4-5-1. 802.1x Setup
Use this screen to enable or disable 802.1x. Press the Space key to choose
Enabled or Disabled mode.
Actions->
<Edit>:
Configures all items. When finished, pressing ESC returns to the action
menu line.
Saves all configured values.
<Save>:
<Quit>: Exits this page and returns to previous menu.
123
Download from Www.Somanuals.com. All Manuals Search And Download.
6-4-5-2. 802.1x System Configuration
After enabling the IEEE 802.1x function, use the 802.1x System Configuration
screen to configure the IEEE 802.1x parameters.
Radius Server IP: Enter the Radius Server IP address.
Shared Key: Enter an encryption key for use during authentication sessions
with the specified radius server. This key must match the encryption key used
on the Radius Server.
NAS, Identifier: Enter the identifier for the radius client.
Server Port: Enter the UDP destination port for authentication requests to the
specified Radius Server.
Enter the UDP destination port for accounting requests to
Accounting Port:
the specified Radius Server.
Actions->
<Edit>: Configures all items. When finished, pressing ESC returns to the action
menu line.
Saves all configured values.
<Save>:
<Quit>:
Exits this page and returns to previous menu.
124
Download from Www.Somanuals.com. All Manuals Search And Download.
6-4-5-3. 802.1x Per Port Configuration
802.1x authentication state can be configured for each port as Disable, Accept, Reject
or Authorize. Press the “ ” key to change the state value for each port.
Space
Bullets and Numbering
Formatted:
The specified port is required to be held in the unauthorized state.
The specified port is required to be held in the Authorized state.
Reject:
Accept:
Authorized: The specified port is set to the Authorized or Unauthorized state in
accordance with the outcome of an authentication exchange between the
Supplicant and the authentication server.
Disable: The specified port is required to be held in the Authorized state.
Actions->
<Edit>: Configures all items. When finished, pressing
menu line.
returns to the action
ESC
<Save>: Saves all configured values.
Displays previous page.
<Previous Page>:
<Next Page>: Displays next page.
Exits this page and returns to previous menu.
<Quit>:
125
Download from Www.Somanuals.com. All Manuals Search And Download.
6-4-5-4. 802.1x Miscellaneous Configuration
Quiet period: Enter the period during which the port doesn’t try to acquire a
supplicant.
Enter the period the port waits to retransmit next EAPOL PDU
TX period:
during an authentication session.
Supplicant timeout: Enter the period of time the switch waits for a supplicant
response to an EAP request.
Server timeout: Enter the period of time the switch waits for a server response
to an authentication request.
Enter the number of authentication that must time-out
Reauthorize Maximum:
before authentication fails and the authentication session ends.
Reauthorize period: Enter the period of time after which clients connected
must be re-authenticated.
Actions->
<Edit>: Configures all items. When finished, pressing ESC returns to the action
126
Download from Www.Somanuals.com. All Manuals Search And Download.
menu line.
Saves all configured values.
<Save>:
<Quit>:
Exits this page and returns to previous menu.
127
Download from Www.Somanuals.com. All Manuals Search And Download.
6-5. System Reset Configuration
128
Download from Www.Somanuals.com. All Manuals Search And Download.
6-5-1. Factory Default
Use this menu to restore all factory default settings. Pressing y will reset the
switch configuration settings to their factory defaults. Rebooting the switch is
necessary for the new configurations to take effect.
y: Resets the switch to the factory default configuration. The software version
that the switch will be reset to can be found on the “System Information” menu
under the main menu “Status and Counters”.
N: Returns to the previous menu.
The unit must be allowed to complete restart process to restore the
Warning:
defaults without an interruption. Manually powering off the system before the
process has been completed may result in corrupted memory and may cause
the unit to not start or come up in an unknown state.
6-5-2. System Reboot
Reboots the switch to enable items that have been configured.
129
Download from Www.Somanuals.com. All Manuals Search And Download.
6-5-3. TFTP Configuration
Use this screen to update firmware, restore EEPROM values or upload
current EEPROM value.
130
Download from Www.Somanuals.com. All Manuals Search And Download.
6-5-3-1. TFTP Update Firmware
Use this screen to update firmware from the TFTP server.
Start the TFTP server, and copy the firmware update version image file to TFTP
server.
TFTP Server IP: Enter the IP address of the TFTP server.
Firmware File Name: Enter the image file name.
Actions->
<Edit>: Configures all items. When finished, pressing ESC returns to the action
menu line.
Starts download of image file from the TFTP server. When the
<Save>:
save is successful, the image is downloaded. Rebooting the switch is necessary
to have the new firmware version take effect.
Exits this page and returns to previous menu.
<Quit>:
131
Download from Www.Somanuals.com. All Manuals Search And Download.
6-5-3-2. TFTP Restore Configuration
Use this screen to restore an EEPROM value or save a previous version of the
image file from the TFTP server.
Start the TFTP server, and copy the firmware update version image file to TFTP
server.
TFTP Server IP: Enter the IP address of the TFTP server.
Restore File Name: Enter the image file name.
Actions->
<Edit>:
Configures all items. When finished, pressing ESC returns to the action
menu line.
Starts the download of the configuration file from the selected source
<Save>:
file on the TFTP server. Reboot is necessary for the new configuration to take
effect.
Exits this page and returns to previous menu.
<Quit>:
132
Download from Www.Somanuals.com. All Manuals Search And Download.
6-5-3-3. TFTP Backup Configuration
Use this screen to save the current EEPROM value to an image file. Then go to
the update configuration page to restore the EEPROM value.
Start the TFTP server, and copy the firmware update version image file to TFTP
server.
Enter the IP address of the TFTP server.
TFTP Server IP:
Enter the image file name.
Restore File Name:
Actions->
Configures all items. When finished, pressing
returns to the action
ESC
<Edit>:
menu line.
<Save>: Starts the upload of the current configuration to the selected
destination file on the TFTP server.
Exits this page and returns to previous menu.
<Quit>:
133
Download from Www.Somanuals.com. All Manuals Search And Download.
6-5-3-4. Save Configuration
The configuration must be saved to the flash memory when it has been
changed. Manually powering off the system before the process has been
completed may result in corrupted memory and may cause the unit to not start
or come up in an unknown state.
134
Download from Www.Somanuals.com. All Manuals Search And Download.
6-6. X-modem Upgrade
1. While booting the switch, press the X key to start the Xmodem routine on the
device.
2. Pressing X will cause the switch Xmodem application to begin and cause the
baud rate to change to 57600 bps. You will need to disconnect the cable
connected to the serial port, and change the baud rate of your hyper-terminal
application on your laptop to 57600 bps, then connect the cable and reconnect
to the switch.
135
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Select “send file" under the "transfer" menu from menu bar.
4. Press the "browse" button to select the path.
5. Select "1K Xmodem" of protocol and press the "Send" button.
6. After successfully upgrading to the new firmware, change the baud rate back
to the default 9600bps.
136
Download from Www.Somanuals.com. All Manuals Search And Download.
7.
Web-Based Management
This section introduces the configuration and functions of the web-based
management of MIL-SM2401M-STK switch series. The managed switch series
provides an embedded HTML website residing in flash memory. It offers advanced
management features and allow users to manage the device from anywhere on the
network through a standard browser such as Internet Explorer or Netscape.
Web-Based Management supports Internet Explorer 5.0. It is based on Java
Applets with an aim to reduce network bandwidth consumption, enhance access
speed and present an easy viewing screen.
Note: By default, Internet Explorer 5.0 or later versions do not allow Java Applets
to open sockets. The user must explicitly modify the browser setting to enable Java
Applets to use network ports.
Preparing for Web Management
Before using the web-based management tool, check the default IP address of
the switch via the Console Menu. Please refer to the
chapter for console login instructions.
Console Management
If necessary, use the console mode to modify the IP address the first time. The
default values are listed below:
IP Address: 192.168.1.77
Subnet Mask:
255.255.255.0
Default Gateway:
192.168.16.254
User Name: root
Password:
root
137
Download from Www.Somanuals.com. All Manuals Search And Download.
Online Help
Online help is available by pressing the Help button for any configuration
questions.
138
Download from Www.Somanuals.com. All Manuals Search And Download.
7-1. System Login
1. Launch Internet Explorer or Netscape.
2. Type http:// and the IP address of the switch in the Location or Address field.
The default IP Address is 192.168.1.77.
3. Press
.
Enter
Figure 5-1: The Password Window
4. In the login screen, type the user name and password. The default is
for
root
both.
5. Press Enter or Click OK and the Home Page screen for web-based
management will appear.
139
Download from Www.Somanuals.com. All Manuals Search And Download.
7-2. Port Status
Bullets and Numbering
Formatted:
“Down” is “No Link”. “UP” is “Link”.
Link:
Displays port status off or on depending on user setting. “Unlink” means
State:
the port is offline or “off ”.
Auto Negotiation: Displays the auto negotiation mode. There are three
selections: Auto, Force and Nway-force.
Displays link speeds of 1000Mbps or 100Mbps or 10Mbps and
Speed Duplex:
full duplex or half-duplex mode.
Bullets and Numbering
Formatted:
Displays the flow control status as enabled or disabled in
Flow Control:
full-duplex mode.
Back Pressure: Displays the backpressure status as enabled or disabled in
half-duplex mode.
Displays the ports incoming and outgoing bandwidth.
Bandwidth:
Bullets and Numbering
Formatted:
Displays the port static priority status as High or Low or Disable.
Priority:
Port Security: Displays the port security as enabled or disabled.
Config: Displays the setting configured by the user.
Displays the negotiation result.
Actual:
140
Download from Www.Somanuals.com. All Manuals Search And Download.
7-3. Port Statistics
The following information provides a view of the current status of the unit.
Pressing the Clear button will return all counts to zero.
141
Download from Www.Somanuals.com. All Manuals Search And Download.
Left click the mouse on the desired port on the graphical image of the switch to
get specific information for that port.
142
Download from Www.Somanuals.com. All Manuals Search And Download.
7-4. Administrator
The management functions include IP address, switch settings, console port
information, port controls, trunking, filter database, VLAN configuration,
spanning tree, port mirroring, SNMP, security manager, TFTP update firmware,
configuration backup, system reset, and reboot.
7-4-1. IP Address
Entering new values and clicking the
button can change the IP Settings.
Apply
The switch must be reset for the new IP address to take effect.
Default IP: 192.168.1.77
Default Subnet Mask: 255.255.255.0
Default Gateway: 192.168.1.6
143
Download from Www.Somanuals.com. All Manuals Search And Download.
7-4-2. Switch Setting
7-4-2-1. Basic Switch Settings
System Name: Displays the name of switch.
System Location: Displays the physical location of the switch.
Displays the name of device type.
System Description:
Displays the switch’s downloaded firmware version.
Firmware Version:
Kernel version: Displays write to default EEPROM value version.
Hardware Version: Displays the switch’s hardware version.
Displays unique hardware address assigned by
MAC Address:
manufacturer.
Module: Displays the type and description of the switch module.
144
Download from Www.Somanuals.com. All Manuals Search And Download.
7-4-2-2. Advanced Settings
Bullets and Numbering
Formatted:
Enable MAC Address Aging Out: Select to enable the MAC address aging out
function.
Enter the number of seconds that an inactive MAC address
Age-Out Time:
remains in the switch's address table. The valid range is 300 to 765 seconds.
Default is 300 seconds.
Limits the packets queuing time in the
Max Bridge Transmit Delay Bound:
switch. If enabled, the packets that exceed the time limit in the queue will be
dropped. This valid values are 1sec, 2 sec, 4 sec and off. Default is 1 second.
Limits the low priority packets queuing time
Enable Low Queue Delay Bound:
in switch. If a low priority packet in the switch exceeds the Max Delay Time, it
will be sent. The valid range is 1to 255 ms.
NOTE: Make sure the “Max bridge transit delay bound control” is enabled
before enabling Delay Bound. The Enable Delay Bound only works under
“Max bridge transit delay bound control is enabled” situation.
Broadcast Storm Filter: The threshold is the percentage of the port's total
bandwidth used by broadcast traffic. To configure broadcast storm control, first
enable it and then set the upper threshold for each individual port. When
broadcast traffic for a port rises above the threshold set, broadcast storm
control becomes active. The valid threshold values are 5%, 10%, 15%, 20%,
25% and OFF.
Bullets and Numbering
Formatted:
145
Download from Www.Somanuals.com. All Manuals Search And Download.
Bullets and Numbering
Formatted:
Priority Queue Service Settings: Select the priority queue service type:
The sequence of packets sent is dependent on
First Come First Service:
the order of arrival. The first packets in the queue are transmitted before any
other packets.
The high priority packets are sent before the low
All High before Low:
priority packets.
Weighted Round Ratio: This option enables the user to choose a ratio of the
number of high priority packets sent before one low priority packet is sent. For
example, 2:1 (2 High : 1 Low) will have the switch send 2 high priority packets
before sending 1 low priority packet.
146
Download from Www.Somanuals.com. All Manuals Search And Download.
Qos Policy: High Priority Levels: 0 to 7 priority level can map to a high or low
queue. When the VLAN Tag number of a frame is mapping as a high priority
level, this frame always has high priority. In this example, the QoS policy
applies to the switch, not for a single port.
147
Download from Www.Somanuals.com. All Manuals Search And Download.
7-4-2-3. Miscellaneous Setting
Collisions Retry Forever:
Disabled – In half duplex, if a collision occurs, the switch will retry 48 times
and then drop frame.
Enabled – In half duplex, if a collision occurs, the switch will retry forever.
Hash Algorithm: CRC Hash or Direct Map for MAC address learning
algorithm.
Select enable or disable for Internal Packet Gap time
IFG Compensation:
compensation configuration.
802.1x Protocol: Select enable or disable for 802.1x protocol.
Recognizes different queries from clients or servers to
IGMP Query Mode:
decide which Query will be the first priority. The modes are:
Auto Mode: Chooses the switch that has the smallest IP address to be set
for the IGMP Query mode.
Enables the switch to be the IGMP Querier.
Enable Mode:
Disable Mode: Disables all other switches from being the IGMP Querier.
148
Download from Www.Somanuals.com. All Manuals Search And Download.
IGMP Theory of Operation
The following three topologies detail how IGMP Query works and to be
configured within a network:
1. Auto mode needs to be enabled when the router’s IP address is smaller than
other switches in the subnet.
149
Download from Www.Somanuals.com. All Manuals Search And Download.
2. IGMP needs to be enabled when the router’s IP address is not smaller than
other switches in the subnet. This Router supports IGMP protocol, but IGMP
has to be enabled, and the Router has to be the Querier.
150
Download from Www.Somanuals.com. All Manuals Search And Download.
3. The following topology must be set when the IP address of the switch is not
the smallest in the subnet. The network will cause a multi-cast storm from the
IGMP client report if it is in Auto mode. All switches must be in disable mode
when the VOD server is configured for IGMP Querier.
Note: It is suggested that the VOD server switch have the smallest IP address.
151
Download from Www.Somanuals.com. All Manuals Search And Download.
7-4-3. Console Port Information
Console is a standard UART interface to communicate with a serial port.
The Windows HyperTerminal program can be used to link the switch with the
console port. In order to change any of these parameters, you must be
connected to the console port.
Baud rate (bits/sec): 9600
Data Bits: 8
Parity Check: none
Stop Bits: 1
Flow Control: none
152
Download from Www.Somanuals.com. All Manuals Search And Download.
7-4-4. Port Controls
The Port Controls menu allows changing of port configurations.
State: User can disable or enable each port.
User can set auto negotiation mode for each port to Auto, Nway
Negotiation:
(specify the speed/duplex on this port and enable auto-negotiation) or Force.
User can set 100Mbps or 10Mbps speed on Ports 1 to 24. User can
Speed:
set 1000Mbps, 100Mbps or 10Mbps speed on Ports 25 and 26, depending on
module installed.
User can set full-duplex or half-duplex mode for each port.
Duplex:
Flow control: User can set flow control function to enabled (ON) or disabled
(OFF) in Full Duplex mode.
Back Pressure: User can set back pressure to enabled (ON) or disabled (OFF)
in Half Duplex mode.
153
Download from Www.Somanuals.com. All Manuals Search And Download.
Band Width: Ports 1 to 24 support by-port ingress and egress rate control. For
example, if port 1 is set to 10Mbps, you can set it’s effective egress rate to
1Mbps and ingress rate to 500Kbps. The MIL-SM2401M-STK will perform
flow control or backpressure to confine the ingress rate to meet the specified
rate.
Enter the port effective ingress rate. The valid range is 0 to 1000. The
In:
unit is 100K.
0: disable rate control.
1 to 1000: valid rate value
Enter the port effective egress rate. The valid range is 0 to 1000. The
Out:
unit is 100K.
0: disable rate control.
1 to 1000: valid rate value.
Priority: This static priority is based on each port setting. If the port priority is set
high, incoming frames from this port will always be high priority frames.
A port in security mode will be “locked” unless address learning is
Security:
enabled. Only the incoming packets with SMAC already existing in the address
table can be forwarded normally. User can disable the port from learning any new
MAC addresses, and then use the static MAC addresses screen to define a list of
MAC addresses that can use the secure port.
Enter the settings, then click the Apply button to save the changes on this page.
154
Download from Www.Somanuals.com. All Manuals Search And Download.
7-4-5. Trunking
The Link Aggregation Control Protocol (LACP) standardized means for
exchanging information between Partner Systems on a link to allow their Link
Aggregation Control instances. To reach agreement on the identity of the Link
Aggregation Group to which the link belongs, move the link to that Link
Aggregation Group, and enable its transmission and reception functions in an
orderly manner. Link aggregation allows grouping of up to eight consecutive
ports into a single dedicated connection. This feature can expand bandwidth to
a device on the network. LACP operation requires full-duplex mode. For
more detailed information refer to IEEE 802.3ad.
If there are two trunk groups A and B, and B group is enabled LACP, and then it
will act as a redundant link (Backup group for Trunk group A). If trunk group A
fails, Group B will be its backup.
155
Download from Www.Somanuals.com. All Manuals Search And Download.
7-4-5-1. Aggregator Setting
System Priority: A value used to identify the active LACP. The switch with the
lowest value has the highest priority and is selected as the active LACP.
To create a trunk across two or more ports:
1.
2.
Choose the "Group ID" and click the
button.
Select
Group ID:
If enabled, the group supports LACP. If disabled, the group is a local
LACP:
static trunking group between two switches. All ports support LACP
dynamic trunking group. If connecting to another device that also supports
LACP, the LACP dynamic trunking group will be created automatically.
3.
Enter the maximum number of ports that can be aggregated at
Work Ports:
the same time. If the group is an LACP static trunking group, the exceeded
ports are on standby and able to aggregate if work ports fail. If the group is a
local static trunking group, the number must be the same as group ports.
4.Select the ports to join the trunking group and click the Add button. If LACP is
enabled, you can configure LACP Active/Passive status for each port. To
156
Download from Www.Somanuals.com. All Manuals Search And Download.
remove a port, select the port to be removed from the Work Ports column
and click the button.
Remove
button to save the new configuration.
5.Click the
Apply
6.Click the Delete button to remove a trunking Group ID.
157
Download from Www.Somanuals.com. All Manuals Search And Download.
7-4-5-2. Aggregator Information
The LACP Aggregator relation information is displayed as shown.
158
Download from Www.Somanuals.com. All Manuals Search And Download.
7-4-5-3. State Activity
(selected) The active port automatically sends LACP protocol packets.
Active
:
Passive (not selected): The passive port does not automatically send LACP
protocol packets, but responds only if it receives LACP protocol packets from
the other device.
A link having either two active LACP ports or one active port can perform
dynamic LACP trunking. A link that has two passive LACP ports will not perform
dynamic LACP trunking because both ports are waiting for an LACP protocol
packet from the opposite device.
If the port has active LACP’s, and you select the trunking port, the active status will be
created automatically.
159
Download from Www.Somanuals.com. All Manuals Search And Download.
7-4-6. Forwarding and Filtering
7-4-6-1. IGMP Snooping
The switch supports IP multicasting. You can enable IGMP via the web
management’s configuration screen. In addition, you can view different
multicast groups, VIDs and member ports, and IP multicast addresses that
range from 224.0.0.0 through 239.255.255.255.
The Internet Group Management Protocol (IGMP) is an internal protocol of the
Internet Protocol (IP) suite. IP manages multicast traffic by using switches,
routers, and hosts that support IGMP. Enabling IGMP allows the ports to detect
IGMP queries and report packets and manage IP multicast traffic through the
switch. IGMP has three fundamental types of messages.
160
Download from Www.Somanuals.com. All Manuals Search And Download.
Message
Query
Description
A message sent from the querier (IGMP router or switch)
asking for a response from each host belonging to the
multicast group.
A message sent by a host to the querier to indicate that the
host wants to be or is a member of a given group indicated in
the report message.
Report
A message sent by a host to the querier to indicate that the
host has stopped being a member of a specific multicast
group.
Leave
Group
161
Download from Www.Somanuals.com. All Manuals Search And Download.
7-4-6-2. Static MAC Address
When a static MAC address is added, it remains in the switch's address table,
regardless of whether or not the device is physically connected to the switch.
This saves the switch from having to re-learn a device's MAC address when the
device is disconnected or powered-off.
To add a static MAC address:
1.Click on Administrator on the main menu.
2.Click on
.
Filter Database
3.Click
. In the MAC address box, enter the MAC
Static MAC Addresses
address to and from which the port should permanently forward traffic,
regardless of the devices network activity.
4.In the
box, select a port number.
Port Number
5.If tag-based (IEEE 802.1Q) VLANs are set up on the switch, static addresses
162
Download from Www.Somanuals.com. All Manuals Search And Download.
are associated with individual VLANs. Type the VID (tag-based VLANs) to
associate with the MAC address.
6.
Click the
button.
Add
7. To delete a MAC address, highlight the selection in the table you want to delete and
then click the Delete button.
163
Download from Www.Somanuals.com. All Manuals Search And Download.
7-4-6-3. MAC Filtering
MAC address filtering allows the switch to drop unwanted traffic. Traffic is
filtered based on the destination addresses.
Steps to specify a MAC address to filter:
1. In the MAC Address box, enter the MAC address to filter.
2. If tag-based (802.1Q) VLAN are set up on the switch, in the VLAN ID box, type
the VID to associate with the MAC address.
3. Click the
button.
Add
4. To delete a MAC address, highlight the selection in the table you want to
delete and then click the Delete button.
NOTE: Changing the VLAN type in the Advanced Switch Setting menu will
cause the contents of this table to clear.
164
Download from Www.Somanuals.com. All Manuals Search And Download.
7-4-7. VLAN Configuration
A Virtual LAN (VLAN) is a logical network grouping that limits the broadcast
domain. It allows you to isolate network traffic so only members of the VLAN
receive traffic from the same VLAN members. Basically, creating a VLAN from a
switch is logically equivalent of reconnecting a group of network devices to
another Layer 2 switch. However, all the network devices are still plugged into
the same switch physically.
The MIL-SM2401M-STK supports port-based, 802.1Q (tag-based) and
protocol-based VLANs. VLAN support is Disabled and all ports belong to a
single broadcast domain by default.
Rebooting the switch is necessary for changes to take effect.
NOTE:
Port-based VLANs
Ethernet frames received on a port are sent only to ports belonging to the same
VLAN group of ports. All ports default belonging to the same VLAN group. The
VLAN information included in Ethernet frames tagged with VLAN IDs is ignored
by the switch in Port Based VLAN mode.
165
Download from Www.Somanuals.com. All Manuals Search And Download.
Tag-based VLAN (IEEE 802.1Q VLAN)
The IEEE 802.1Q specification is the standard for Port-based Tagging.
Therefore, it is possible to create a VLAN across devices from different switch
suppliers. IEEE 802.1Q VLAN uses a technique to insert a “tag” into the
Ethernet frames. The tag contains a VLAN Identifier (VID) that indicates the
VLAN numbers.
Protocol-based VLAN
In order for an end station to send packets to different VLANs, it has to be either
capable of tagging the packets it sends with VLAN tags OR be attached to a
VLAN-aware bridge. The VLAN-aware bridge must be capable of classifying
and tagging the packet with different VLAN ID. The classification and tagging
of the packets is based on default PVID and other information about the packet,
such as the protocol.
MIL-SM2401M-STK will support protocol-based VLAN classification by means
of both built-in knowledge of layer 2 packet formats used by selected popular
protocols, such as Novell IPX and AppleTalk’s EtherTalk, and some degree of
programmable protocol matching capability.
166
Download from Www.Somanuals.com. All Manuals Search And Download.
Create a VLAN and add tagged member ports to it.
1.Click the Add button to create a new VLAN group.
2.Enter the VLAN name, group ID and select the members for the new VLAN.
3.Click the Apply button.
4.If the number of groups exceeds the limit for a single page, click the
button to view other VLAN groups.
NextPage
NOTE: Use the Edit button to view and modify existing VLAN Groups.
167
Download from Www.Somanuals.com. All Manuals Search And Download.
7-4-7-1. VLAN Operation Mode 802.1Q (802.1Q VLAN)
On this page, the user can create Tag-based VLANs, and enable or disable
GVRP protocol. There are 256 VLAN groups provided to configure. If 802.1Q
VLAN is enabled, then all ports on the switch belong to the default VLAN1. The
default VLAN1 can’t be deleted.
GVRP (GARP VLAN Registration Protocol)
GVRP allows automatic VLAN configuration between the switch and nodes. A
GVRP request can be sent using the VID of a VLAN defined on the switch when
the switch is connected to a device with GVRP enabled. The switch will
automatically add that device to the existing VLAN.
168
Download from Www.Somanuals.com. All Manuals Search And Download.
Security VLANs
Security VLAN’s allow for limiting telnet, SNMP and web access to the switch to
a specific VLAN. The VID of the Security VLAN may be changed from 255 to
another value after creating the VLAN. The new VID must not already exist on
the box.
169
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic
To create a VLAN and add tagged member ports to it:
1.Select the Add button to create a new VLAN.
2.Enter a name for the new VLAN.
3.Enter a VLAN ID (2 to 4094). The default is 1.
4.Choose the protocol type. Default is NONE.
5.From the Available ports box, select ports to add to the switch and click Add.
If the trunk groups exist, you can see it here (ex:Trunk1,Trunk2…) and
configure it as a member of the VLAN or not.
6.Click the Next button.
170
Download from Www.Somanuals.com. All Manuals Search And Download.
Use this page to set the outgoing frames are VLAN-Tagged frames or not, and
then click the button.
Apply
Tag: Outgoing frames with VLAN-Tagged.
Untag: Outgoing frames without VLAN-Tagged.
171
Download from Www.Somanuals.com. All Manuals Search And Download.
Port VID
To configure port VID settings:
From the main
VLAN page, select
Settings.
Port VLAN ID
802.1Q
Port VLAN ID
Set the port VLAN ID that will be assigned to untagged traffic on a given port.
This feature is useful for accommodating devices that you want to participate in
the VLAN but that don’t support tagging. Only one untagged VLAN is allowed
per port. Other VLANs need to be tagged. The VLAN ID must be the same as
the VLAN ID of the port that belongs to the VLAN group, or the untagged traffic
will be dropped.
172
Download from Www.Somanuals.com. All Manuals Search And Download.
Ingress Filtering
Ingress filtering lets frames belonging to a specific VLAN to be forwarded if the
port belongs to that VLAN.
Enable: Forward only packets with VID matching this port's configured VID.
: Disable Ingress filter function.
Disable
Acceptable Frame Type
ALL: All packets are acceptable.
Only packets that match the VLAN ID will have permission to go
Tag Only:
through the port.
VLAN ID Range
Ports assigned to the same VLAN ID will be in the same VLAN group. Select
the range for the VLAN ID for the group.
Click the Apply button to save the configuration. Click the Default button to
return the settings to the default configuration.
173
Download from Www.Somanuals.com. All Manuals Search And Download.
7-4-8. Spanning Tree
The Spanning-Tree Protocol (STP) is a standardized method (IEEE 802.1D) for
avoiding loops in switched networks. When STP is enabled it ensures that only
one path at a time is active between any two nodes on the network.
Spanning-Tree Protocol can be enabled using web management’s switch
setting advanced item, and selecting enable Spanning-Tree protocol. By default,
spanning tree is disabled on the switch.
It is recommended that STP be enabled on all switches to ensure a single active
path on the network.
174
Download from Www.Somanuals.com. All Manuals Search And Download.
7-4-8-1. System Configuration
Spanning Tree information for the Root Bridge at the bottom is for display only.
Configure new values for the STP parameters at the top.
STP State: Enable the Spanning Tree function by marking the box.
The value used to identify the root bridge. The bridge with the lowest
Priority:
value has the highest priority and is selected as the root. Enter a number 1
through 65535.
The number of seconds a bridge waits without receiving
Max Age:
Spanning-Tree Protocol configuration messages before attempting a
reconfiguration. Enter a number 6 through 40.
175
Download from Www.Somanuals.com. All Manuals Search And Download.
The number of seconds between the transmission of
Hello Time:
Spanning-Tree Protocol configuration messages. Enter a number 1 through 10.
Forward Delay Time: The number of seconds a port waits before changing
from its Spanning-Tree Protocol learning and listening states to the forwarding
state. Enter a number 4 through 30.
Click the Apply button to save the new configuration.
176
Download from Www.Somanuals.com. All Manuals Search And Download.
7-4-8-2. Per Port Configuration
The path cost and priority can be configured for each port.
1. Select the port to be configured in the Port menu list by clicking on it.
2. Enter the Path Cost and Port Priority settings:
177
Download from Www.Somanuals.com. All Manuals Search And Download.
PathCost: Path Cost specifies the path cost of the port that the switch uses to
determine which ports are the forwarding ports. The lowest number
becomes the forwarding port. The range is 1-65535 and the default value is
based on IEEE802.1D.
10Mb/s = 50-600
100Mb/s = 10-60
The switch must be rebooted if the values are changed.
Port Priority: A change to the Port Priority affects which port will be the root
port. The lowest number has the highest priority. The range is 0-255 and the
default setting for all ports is 128. The switch must be rebooted if the values
are changed.
3. Click the Apply button to save the new configuration.
178
Download from Www.Somanuals.com. All Manuals Search And Download.
7-4-9. Port Mirroring
The Port Mirroring feature is disabled by default. Selecting enable from the pull
down menu will cause the selected traffic from the selected monitor ports to be
mirrored to the selected analysis port. Press the
changes.
button to submit the
Apply
Port Mirroring State: Enables or Disables the port mirroring function.
179
Download from Www.Somanuals.com. All Manuals Search And Download.
Enabled states include RX, TX or Both.
All mirrored traffic is sent out this port.
Analysis Port:
Monitor Port:
The ports you want to mirror. All source port traffic will be copied
to a mirror port. You can select a maximum of 25 source ports in the switch. If
you want to disable the function, you must select monitor port to none.
180
Download from Www.Somanuals.com. All Manuals Search And Download.
7-4-10. SNMP Management
A SNMP is a protocol that governs the transfer of information between
management and agent. The switch supports SNMP V1. Any Network
Management station running the Simple Network Management Protocol (SNMP)
can manage the switch provided that the Management Information Base (MIB)
is installed.
Use this menu to define management stations as trap managers and to enter
SNMP community strings. Users can also define community strings for a name,
location, and contact person for the switch.
181
Download from Www.Somanuals.com. All Manuals Search And Download.
7-4-10-1. System Options
Enter the Name location and contact information for the switch. Each field
allows entry of 26 characters.
: Enter a name to be used for the switch.
Name
Location: Enter the location of the switch.
Contact: Enter the name of a person or organization.
Click the
button to save the System Option information.
Apply
7-4-10-2. Community Strings
Community Strings serve as a password between the trap manager and the
switch.
Enter a unique community string and select one of the
New Community String:
following options:
RO (Read only): Enables requests accompanied by this string to display
MIB-object information.
Enables requests accompanied by this string to display
RW (Read write):
MIB-object information and to set MIB objects.
Click the
button to add the new community string. To remove a
Add
community string, select it from the list of current strings and click the
button.
Remove
Bullets and Numbering
Formatted:
7-4-10-3. Trap Managers
A trap manager is a management station that receives traps. Traps are the
system alerts generated by the switch. If no trap manager is defined, no traps are
182
Download from Www.Somanuals.com. All Manuals Search And Download.
issued. Create a trap manager by entering the IP address of the station and a
community string.
IP Address: Enter the IP Address of the Trap Device.
Community: Enter the Community String for the Trap Device.
Click the
button to add the new trap manager. To remove a trap manager,
Add
select it from the list of current managers and click the Remove button.
183
Download from Www.Somanuals.com. All Manuals Search And Download.
7-4-11. Security Manager
The user can change the user name and password to keep the switch secure.
After entering a new user name and password, click the Apply button to submit
the changes. The default user name and password are below.
User Name: root
Password: root
184
Download from Www.Somanuals.com. All Manuals Search And Download.
7-4-12. 802.1X
When the IEEE 802.1x function is enabled, the parameters may be configured
here.
7-4-12-1. System Configuration
Radius Server IP: Set the Radius Server IP address.
Server Port: Set the UDP destination port for authentication requests to the
specified Radius Server.
Set the UDP destination port for accounting requests to the
Accounting Port:
specified Radius Server.
Shared Key: Set an encryption key for use during authentication sessions with
the specified radius server. This key must match the encryption key used on the
Radius Server.
NAS, Identifier: Set the identifier for the radius client.
Click the Apply button to save the System Configuration information.
185
Download from Www.Somanuals.com. All Manuals Search And Download.
7-4-12-2. Per Port Configuration
Each port can be configured to one of the following four states:
Reject: The specified port is required to be held in the Unauthorized state.
Accept: The specified port is required to be held in the Authorized state.
Authorized: The specified port is set to the Authorized or Unauthorized state in
accordance with the outcome of an authentication exchange between the
Supplicant and the authentication server.
Disable: The specified port is required to be held in the Authorized state.
Click the
button to save the Per Port Configuration information.
Apply
186
Download from Www.Somanuals.com. All Manuals Search And Download.
7-4-12-3. 802.1x Miscellaneous Configuration
Quiet period: Set the period during which the port doesn’t try to acquire a
supplicant.
Set the period the port waits to retransmit next EAPOL PDU during
TX period:
an authentication session.
Supplicant timeout: Set the period of time the switch waits for a supplicant
response to an EAP request.
Set the period of time the switch waits for a server response to
Server timeout:
an authentication request.
Max requests: Set the number of authentication that must time-out before
authentication fails and the authentication session ends.
Reauth period: Set the period of time after which clients connected must be
re-authenticated.
Click the
button to save the Per Port Configuration information.
Apply
187
Download from Www.Somanuals.com. All Manuals Search And Download.
7-4-13. TFTP Update Firmware
The following menu options provide some system control functions to allow a user
to update firmware and remotely boot the switch system:
Executing TFTP software
•
•
•
•
Copy firmware update version image.bin to TFTP software directory.
In web management select
Administrator—TFTP update firmware.
Download new image.bin file. In web management, press
<update
.
firmware>
188
Download from Www.Somanuals.com. All Manuals Search And Download.
7-4-14. Configuration Backup
7-4-14-1. TFTP Restore Configuration
Use this screen to set TFTP server IP address. You can restore EEPROM value
from here, but you must put the image back in the TFTP server. The switch will
download back flash image.
7-4-14-2. TFTP Configuration Backup
Use this screen to set the TFTP server IP address. You can save current
EEPROM value from here, then go to the
restore the EEPROM value.
screen to
TFTP Restore Configuration
189
Download from Www.Somanuals.com. All Manuals Search And Download.
7-4-15. Factory Default
Resets the Switch to default configuration.
Default IP Address: 192.168.1.77
Default Gateway: 192.168.16.254
Subnet mask: 255.255.255.0
All other settings default to either Disabled or no value.
7-4-16. System Reboot
Select Reboot to restart the system with the current saved configuration.
190
Download from Www.Somanuals.com. All Manuals Search And Download.
7-5. Panel List
The Panel list option will display the switch panel in a GUI interface format.
When stacking has been enabled, the display will include the slave switches in the
display. Clicking on each port will give the current port status information.
191
Download from Www.Somanuals.com. All Manuals Search And Download.
7-6. IP Stacking
The IP stacking function allows up to eight MIL-SM2401M-STK switches to be
joined as a single unit group. The stackable switches can then be managed
through a single IP address. When configuring the stacking function, please
review the following guidelines.
„
Any port on the switch can be used for stacking.
„ All switches which are to be stacked together must be in the same network
before the stacking function can be configured.
„ The master switch must be configured first, followed by the slave switches.
„ Slave switches can be viewed independently as read-only data. Updates
must be made through the master switch.
„ To remove the master switch from a stacking group, remove all slave
switches first and then remove the master switch from stacking group.
„ If the master switch has been removed from the stacking group before the
slave switches, use the
to re-configure
Console Interface Menu EITHER
the switch configuration for each slave switch OR re-configure one of the
slave switches as the master switch.
192
Download from Www.Somanuals.com. All Manuals Search And Download.
7-6-1. Setting up an IP Stacking Group
Select
in the menu bar and enter the following information for the
IP Stacking
master switch in the stack. Click the Apply button to save the new configuration.
Group ID (0...65535): Assign a group ID for stacking group. The switches in
the same stacking group have same group ID.
Stacking Mode: Select one of the following as the stacking mode for each
switch.
Disable: The stacking function is not enabled.
One switch must be selected to control all other switches in
Master:
stacking group. Only one switch can be assigned to be the master switch in
one stacking group. Once the stacking group is set up, the master switch
will control all switches in the stacking group.
All remaining switches in a stacking group must be configured to
Slave:
slave mode. Once the stacking group is set up, the slave switches can only
be configured through the master switch.
Enter a brief description of the switch.
System Information:
193
Download from Www.Somanuals.com. All Manuals Search And Download.
Once the stacking function has been configured for the master switch, use Cat. 5
cable to connect each switch in the stacking group. Wait a few minutes for the
master switch to communicate and collect the data from the slave switches.
Connect to the master switch through the Web-based interface to access the
following screen.
1.
2.
3.
The web-based interface menu bar for the master switch is used to configure
each of the slave switches in the stacking group.
To configure a switch in the stacking group, click on the link at the top of
screen and log in to the switch to be configured.
Follow the same procedure for configuring each of the slave switches.
194
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Troubleshooting
This section is intended to help you solve some common problems encountered
while using the MIL-SM2401M switch series.
Incorrect connections
The switch auto-detects the polarity and direction of the UTP cable attached. If no
link I seen, then check the following:
„ Faulty or loose cables
Look for loose or obviously faulty connections. If they appear to be OK, make
sure the connections are snug. If that does not correct the problem, try
different cables.
„ Non-standard cables
Non-standard and miswired cables may cause numerous network collisions
and other network problems. This can seriously impair network performance.
A category 5 cable tester is a recommended tool for every network installation.
„ Improper Network Topologies
It is important to make sure that you have a valid network topology. Common
topology faults include excessive cable length and too many repeaters or
hubs between end nodes. In addition, you should make sure that your network
topology contains no data path loops. Between any two ends nodes, there
should be only one active cabling path at any time. Data path loops will cause
broadcast storms that will severely impact your network performance.
195
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostic LED Indicators
The switch can be easily monitored through panel indicators to assist in
identifying problems.
If the power indicator does turn on when the power cord is plugged in, you may
have a problem with power outlet or power cord. However, if the switch powers off
after running for a while check for loose power connections, power losses or
surges at power outlet. If you still cannot resolve the problem, contact your local
dealer for assistance.
„ Cabling
RJ-45 ports: Use unshielded twisted-pair (UTP) or shielded twisted-pair (STP)
Ω
cable for RJ-45 connections: 100
Category 3, 4 or 5 cable for 10Mbps
Ω
connections or 100 Category 5 cable for 100Mbps connections. Be sure that
the length of any twisted-pair connection does not exceed 100 meters (328 feet).
100BASE-FX and 1000BASE-X Fiber port: Multi-mode fiber connector types must
use 50/125 or 62.5/125 m multi-mode fiber cable. Two devices may be
μ
connected over a 2-kilometer distance. Single-mode fiber connector types must
use 9/125 m single mode fiber cable. Two devices may be connected over a15
μ
to 60-kilometer distance in full duplex operation in single mode.
1000Base-TX ports use all 8 wires for communication and requireCat-5 or better
cable quality.
196
Download from Www.Somanuals.com. All Manuals Search And Download.
9.
Technical Specifications
This section provides the specifications of MIL-SM2401M-STK switch
product.
IEEE802.3 10BASE-T
IEEE802.3u 100BASE-TX/100BASE-FX
IEEE802.3z Gigabit SX/LX
IEE802.3ab Gigabit 1000T
IEEE802.3x Flow Control and Back pressure
Standard
IEEE802.3ad Port trunk with LACP
IEEE802.1d Spanning tree protocol
IEEE802.1w Rapid Spanning Tree
IEEE802.1p Class of service
IEEE802.1Q VLAN Tagging
IEEE 802.1x user authentication
Switch architecture
Back plane
Store and forward switch architecture.
8.8Gbps
System Power
10/100TX RJ-45 Port: 100Mbps,Link/Active,
Full-duplex/Collision
LED Indicators
Gigabit Fiber: Link/ Activity
Gigabit Copper: Link/Activity, Full duplex/collision,
197
Download from Www.Somanuals.com. All Manuals Search And Download.
1000Mbps, 100Mbps
100FX module: Link/Activity, Full duplex1000Mbps,
100Mbps
100FX module: Link/Activity, Full duplex
10/100TX: RJ-45
100FX(Multi /Single Mode) module: SC
Gigabit SX/LX module: SC
Gigabit 1000T module: RJ-45
Connector
MAC address
Memory
8K MAC address table with Auto learning function
3Mbits for packet buffer
CPU
ARM-7
Flash ROM
System memory
Power Consumption
Dimensions
Power Supply
EMI
1 Mbytes
8Mbytes
34Watts(Maximum)
440mm(W) x 161mm(D) x 44mm(H)
100-240V AC, 50-60Hz, 0.8A(maximum)
FCC Class A, CE
Safety
UL, cUL, CE/EN60950
198
Download from Www.Somanuals.com. All Manuals Search And Download.
90000416 Rev A
199
Download from Www.Somanuals.com. All Manuals Search And Download.
|