OPERATING
GUIDE
FOR YOUR
MAGNUM ALERT-825/
MAGNUM ALERT-825HS
SECURITY SYSTEM
0 1880, NAPCO
N A P C O
Download from Www.Somanuals.com. All Manuals Search And Download.
Please read this guide thoroughly
to familiarize yourself with your new
security system. Keep this booklet
handy for future reference. Note
especially the ALARM PLAN on
page 15. Your alarm specialist will
help you fill it out and explain the
various features and operating
procedures for your new Magnum
Alert-825/825HS.
The Napco Magnum Alert-8254
825HS has such a wide variety of
features that few, if any, security
systems will ever need them all.
Your alarm professional has
chosen appropriate features for
your situation. Ask him about
them.
Your Magnum Alert-825/825HS
is carefully designed and
engineered to the highest indus-
try standards. To provide optimum
safety and security with this
equipment, we recommend that
the user become thoroughly
familiar with the unit and periodi-
cally check its condition and state
of readiness.
NOTICE
You’ll probably find items men-
tioned in this booklet which do not
apply to your system. DON’T
WORRY!
Shunt
Panic
Mini-Sounder
The face of the keypad lifts up to
reveal a convenient index of pro-
tected zones.
Download from Www.Somanuals.com. All Manuals Search And Download.
the security system (alarm, trouble, low
battery, etc.). (optional)
Dlgltal Communicator
Abort Delay
Reports burglary and emergencies directly
to the central station over telephone lines.
A delay period that allows the system to be
reset before it reports to a central station.
Shunt Button
Labelled "S" on the Digit-Key keypad. Lets
you manually remove one or more protective
zones from the system.
Alarm Plan
Digit-key keypad puts Control
Napco’s
ldentifies the areas of your premises pro-
tected by each zone of protection and lists
zone features. (See page 15)
Center functions at your fingertips. It can
be mounted either at the Control Center or
anywhere in your premises.
Zones
Independent, circuits that protect specific
areas of your premises.
Ambush Code
Exlt/Entry Delay
Auto Shunted Zone: A zone capable of
being automatically bypassed (shunted)
out of the protection system if it is in
“trouble” (faulty) when you attempt
to arm the system.
A one or two-digit code used before an arm/
disarm code that causes a silent report to
be sent to a central station. (Optional)
Lets you exit and enter your premises without
setting off an alarm after the system is armed.
Hold Down Functlon
Digit keys have secondary functions which
are activated by holding down a digit until
a beep is heard.
Arming/Disarming
Burglary Zones: Detect intrusion.
Day Zone: A zone programmed to cause
visual and audible ( optional) indication at
the Digit-Key keypad when it is in ”trouble”
during the disarmed period.
Exlt/Entry Follower Zone: Provides
exit and entry delay for interior devices.
Entry delay only occurs if re-entry takes
place through the normal exit/entry door.
Group Shunt Zones: A group of zones
programmed so they can be manually by
passed (shunted) all at once.
Turning your system ON or OFF. This can
be done by entering a code on the Digit-
Key keypad, or by turning an optionalkey-
Switch.
Fallback Code
A pre-programmed four-digit code that may
be used to disarm your system should all
user codes be erased (as after an extended
power failure).
Arm/Dlsarm (Personal) Codes
Up to 4 four-digit codes used to arm and
disarm the system from the keypad.
Mlnl-Sounder
Buzzer at each Napco Digit-Key keypad
warns that entry delay time has started. It
also sounds when you attempt to arm the
system if a particular zone is in “trouble”. It
also verifies contact with a central station
when a closing signal is sent (optional).
Battery
Stand by battery Is placed in the Control
Center ox to provide backup protection in
b
Priority Zones: When a zone selected
for the feature is in “trouble” it will be
impossible to arm the Control Center.
Selectlve Shunted Zones: Zones that
can be individually bypassed (shunted)
using the Shunt Button.
the event of a power loss.
Central Station
and emergency
Monitors incoming burglary
messages from the Digital
Panic Buttons
Two buttons (* and #) on the Digit-Key
keypad which will alert the central station
of an emergency.
Communicator,
and alerts the proper authorities. (Optional
feature)
Trouble Zones: Zones that cannot be
armed becauseof an open window, door
or other problem in the area.
Control Center
Report
24 Hour Zone: Are always armed and
ready at all times to respond to an emer-
gency situation.
A communication sent to a central station
The heart of the Magnum Alert-825 security
3
indicating a specificchange in condition of
system: it controls all system functions.
Download from Www.Somanuals.com. All Manuals Search And Download.
Mint-Sounder
lndicator Lights
l
Steady Tone: day zone in trouble;
entry delay in progress; system
armed with a priority zone in trouble.
ARMED/MEMORY (Red)
l
l
Steady- system is armed.
Flashes alarm condition.
-
Flashes indicate the number of
zone(s) which were violated.
(see page 5, Key 2)
l
Beep (2 seconds): system armed
with any zone auto shunted; or
battery power low.
STATUS (Green)
l
Steady
zones okay.
Flashes a non-24 hour zone is
in trouble. Flashes indicate the
number of the zone(s) that are in
trouble. Note: to stop flashing
hold down Key 3 for two seconds,
-
system is disarmed, all
Arm-Disarm/Run/Load
Switch
l
-
l
Used to load (program-in) user
arm/disarm codes. Slide switch
to the right (LOAD) position when
entering codes (refer to Selecting
Your Codes on page 7).
SHUNT (Yellow)
Steady
Be sure to return theswitch to the
center (RUN) position after all
codes have been entered. Setting
this spring-return switch to the
left will also arm or disarm the
system (unless this option has
been removed). Your system
will not operate with the switch in
the LOAD position.
-
one or more zones
manually shunted (bypassed).
NOTE: all three lights flashing to-
gether indicates that AC power has
been lost. Reset indication with
Key 9 (see page 5).
Download from Www.Somanuals.com. All Manuals Search And Download.
Your Magnum Alert-825/825HS Security System has three basic components:
1. Zones
2. The Dlglt-Key Keypad
3. The Alarm Output
Lets you program arm/disarm
codes; arm and disarm the system;
check the condition(status) of each
zone; temporarily bypass (shunt)
individual (or group of) zones; send
an ambush alarm; cancel exit/entry
delay; test the battery and alarm
devices; reset the AC-failure indica-
tion; and bypass a
Your system is capable of
When any zone is activated, the
Control Center responds by sound-
ing an audible alarm and/or alerting
a central station (optional). Your
alarm specialist has programmed
monitoring up to six separate areas
of your premises, including Am-
bush/Panic and Auxiliary zones.
Each zone is an independent cir-
cuit that protects a specific area of
your premises. For example: your
alarm specialist may have set aside
a zone for window protection, exit/
entry delay, interior space protec-
tion, safe and valuables protection
or emergencies. Each zone can be
“programmed’ to react in aspecific
manner. Check and be certain that
you know what each zone protects.
your system to react in a specific
manner to each type of emergency.
Be sure you understand how your
system responds to these emer-
gencies.
Bypass Zone.
Three lights and a Mini-Sounder
on the Digit-Key keypad monitor
the system.
Download from Www.Somanuals.com. All Manuals Search And Download.
need, and change them as often
as you feel necessary (refer to
Changing or Voiding a Code).
Selecting Your Codes
The Digit-Key Keypad
To program these codes, slide
the ARM-DISARM/RUN/LOAD
switch (upper left corner of the
Control Center, see page 4) to the
right (LOAD). The three lights on
the keypad will flash rapidly, and
the Mini-Sounder will beep. At the
keypad, enter any combination of
up to four digits (there is no zero)
as follows:
All security system operations are
carried out at the keypad. Each key
hasaspecialfunction of its own (see
“CONTROLS” page 5) plus the
ability to arm and disarm the system
when they are used in a preselected
combination (codes).
Easy Arming
(MA-825HS only)
If programmed, this feature
permits quick arming by momen-
tarily pressing Key 8. Disarming,
however, will still require entry of
a complete code.
Personal ( Arm/Disarm)
Codes
Press:
l S + 1 + Four digit First User’s
Personal Code
You can choose up to4 four-digit
codes which will allow you to arm
and disarm your system. Any of these
codes can easily be changed, thus
allowing temporary guests, baby-
sitters, employees, etc., access to
the premises. When no longer need-
ed, the codes can be changed or
removed from service.
S + 2 + Four digit Second
User’s Personal Code
Changing or Voldlng
a Code
l
S
+3
+
Four digit Third User’s
Personal Code
Changing any user’s code is
accomplished by using the fore-
going procedure and simply chang-
ing the 4-digit combination. Thus.
User 3’s code:
l S + 4 + Four digit Fourth
User’s Personal Code
After all user codes have been
entered, return the ARM-DISARM/
RUN/LOAD switch at the Control
Center to the center( RUN) position.
Remember: your system will not
operate with the switch in the LOAD
position.
Your security system cannot be
disarmed by unauthorized persons.
It will respond only when a code of
your choosing is entered through
the keypad.
1. Set the ARM-DISARM/RUN/
LOAD switch to LOAD.
2. Press S + 3 + Four new digits,
user 3’s new code.
3. Return the ARM-DISARM/
RUN/LOAD switch to RUN.
NOTE: You need not assign all four
codes. Use only as many as you
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Sounder will warn you that exit-
delay time has expired and entry-
delay time has started. To avoid
causing an alarm, quickly return
to the keypad and enter your code
to disarm the Control Center. You
may then rearm and try to exit again.
will flash once for Zone 1; pause;
then flash three times for Zone 3.
Try to clear the troubled zone(s)
yourself. In this example you can
clear the zones by merely closing
the back door and the window.
If the zone cannot be fixed (green
light still flashing), it may still be
possible to arm the system without
the protection of that zone. Check
your Alarm Plan (see page 15). If
the zone in trouble is not designated
as a Priority Zone, you will be able
to arm your system anyway. A 2-
second beep at the keypad Mini-
Sounder will alert you that the sys-
tem was armed with a zone auto-
matically bypassed (auto-shunted)
and no alarm will occur. Be sure to
have all zones in trouble repaired
as soon as possible! If you cannot
clear the zone yourself, call your
alarm specialist.
Checking AC Power
If the three lights of your keypad
are blinking slowly, you have lost
AC power. Check to see if there
has been a general power outage,
or if the Control Center’s trans-
former is disconnected. If you must
operate without AC power, press
Key9 to stop the lights from blink-
ing. Next, test your standby
System Does Not Respond
to Personal Code
battery by pressing Key 1. If the
alarm doesn’t sound, or is weak,
replace the battery. Check your
battery weekly.
If after an extended power failure
your personal codes do not work,
you can temporarily use the " Fall-
back” code to operate the system.
To restore personal codes, see page
7 “Selecting Your Codes”.
Armlng The System Before
You Leave
Before you attempt to arm the
system, check the STATUS light
on the keypad. If the light is on,
you may enter your code, but be
prepared to leave immediately.
Upon arming, the red ARMED/
MEMORY light will come on and
the green STATUS light will go out.
Leave immediatelythrough the exit/
entry door before the exit-delay
time runs out. If you take too long
to leave the premises, the Mini-
Arming With A Zone
In Trouble
If the green STATUS light is flash-
ing, at least one’non-24 Hour Zone
is in trouble (in an open or shorted
condition) and incapable of being
armed. Count the number of flashes
to determine the zone(s) in trouble.
For example, if your back door is
open on Zone 1 and a window is
open on Zone 3, the STATUS lamp
You cannot arm your system if a
zone programmed as a Priority Zone
is in trouble. The Mini-Sounder will
come on, but the ARMED/MEMORY
light will not. To silence the sounder,
re-enter your code to disarm.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: If you enter the wrong code,
you must wait at least 2 seconds
before re-entering. If there was an
extended power failure and your
system does not respond to your
correct code, enter your pre-
programmed “Fallback” code to
disarm. See page 8.
To identify which zone(s) were
violated, hold down Alarm History
Key 2 until it beeps. The red ARMED/
MEMORY light will flash to indicate
the last alarm condition. Count the
number of flashes to determine
which zone(s) require attention.
NOTE: If an alarm occurredand the
red light did not flash, a 24 Hour
Zone (see your Alarm Plan) was
violated. The cause of the alarm
must be determined and cleared
before you can rearm your Control
Center.
If trouble is encountered on a
zone programmed as a Priority-
with-Bypass Zone however, enter
your code to silence the Mini-
Sounder and disarm; hold down
Reset Key 9 until it beeps (this will
bypass the alarm condition); then
enter your code to rearm.
Ambush Code (optlonal)
If an intruder forces you to disarm
your system, enter your prepro-
grammed 1- or P-digit Ambush
Code before your disarm code. This
activates your Ambush Zone, which
is usually programmed to send a
silent alarm to a central station
(optional feature). If your system is
monitored by a central station, be
sure to memorize your ambush code.
Disarming When
You Return
When you enter through the exit/
entry door, the Mini-Sounder will
come on during the entry period to
remind you to disarm. Check the
red ARMED/MEMORY light; if it is
flashing, an alarm occurred while
you were out. Using your code,
disarm the system immediately
during the entry period to prevent
an alarm and to silence the Mini-
Sounder.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
disarm code to arm your remaining
zones. The green light will go OFF,
and the red ARMED/MEMORY light
will come ON. The yellow light will
go OFF when you disarm again indi-
cating that the shunted zones are
no longer shunted.( Note: The shunt
light does NOT come on when zones
are auto-shunted.)
Panic Zone
Arming Wlth Selective
To activate the panic zone,
simultaneously press the two keys
Zone Shunting
Your alarm specialist may have
opted for one or more zones that
can be selectively shunted
(removed) from the system. Since a
shunted zone cannot cause an
alarm, you may wish to use this
feature to turn OFF the interior
areas while arming, and keeping
your perimeter zones (windows,
doors, etc.) active.
To arm, check the green light to
make sure no zone is in trouble.
Press the shunt button ( labeled "S”),
and then the number of the zone (1
through 6) you wish to shunt
Your alarm specialist may also
have opted for interior zones to all
be “group shunt” zone-s Shunt
marked * and
#
on the Digit-Key
keypad. The panic zone can be pro-
grammed to send a silent alarm to a
central station. activate an audible
alarm, or both.
Arming With
Instant Protectlon
Pressing key 4 (until you hear
a beep) will cancel the exit/entry
delay on the exit/entry zone when
arming. The red ARMED/MEMORY
light will flash rapidly to indicate
this condition. If someone enters
through the exit/entry zone, an
alarm will sound immediately.
these zones simply by pressing the
"S" key twice. The yellow shunt light
will come ON whenever you shunt
one or more zones. Enter your arm/
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Your Alarm Specialist may have
programmed your security system
EMERGENCY SERVICES
MONITORS YOUR
SYSTEM 24 HOURS
(Police, Medical Etc)
to be monitored by
a
central station.
The built-in digital communicator
can transmit emergency signals to
the central station 24 hours a day.
ALERT-825/825HS
COMMUNICATOR
PR
PREMISES
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Abort Delay
Opening and Closing
Central Station Rlngback
The central station will acknowl-
edge the fact that you have armed
your system by “ringing back” with
a short beep from the Mini-Sounder.
(This is an optional feature that
sponds to closing reports only.)
Note which zones on your alarm
plan have abort delay. This is a
delay that enables you to reset the
system before a zone condition
report is sent to the central station.
Non-24 hour zone reports are
aborted by arming and then disarm-
ing. 24 hour zones, however, must
first be repaired.
Reporting
An optional feature that permits
the central station to receive a
signal each time the system is
armed, disarmed or both (up to 4
individual users can be identified).
12
Download from Www.Somanuals.com. All Manuals Search And Download.
The following information is
applicable only where local
general power outage. If there is,
you will be operating from your
standby battery. When AC power is
restored. the Mini-Sounder will
come back on. Press the spring-
loaded switch again to silence the
Mini-Sounder.
Fire-Detector Reset
After a fire alarm, the red FIRE
ALARM light will be on. Press the
ordinance permits use of your alarm
Control Center for fire detection
SILENCE
&
FIRE RESET switch to
clear the smoke detectors.
Controlling Your
Alarm/Battery Test
Fire Circuit
If your alarm specialist installed
smoke detectors or heat sensing
thermostats, you have 24 hour fire
protection. This optional Fire Pro-
tection Zone is always active, even
though your system may be dis-
armed. An optional Fire Supervision
and Indicator Station on the Control
Center provides the following fire
circuit controls.
The fire alarm bell/siren and
standby battery should be tested
weekly. Disarm the Control Center.
Fire-Zone Check
The Mini-Sounder on the Fire
Supervision and Indicator Station
signals a problem on the Fire Zone.
Press the spring-loaded SILENCE
8 FIRE RESET switch to shut off the
Mini-Sounder. The red TROUBLE
light will come on until the Fire
Zone is cleared. When the zone is
restored, the Mini-Sounder will
signal again to indicate that the
Fire Zone is functional. Press the
Push the BATTERY
&
BELL TEST
switch down and listen to the bell/
siren. If the alarm sounds weak,
the battery is faulty. Call for service.
Would You Like More
Safety Informatlon?
For information on home fire de-
tection, burn safety, and home fire
safety, contact the National Fire
Protection Association, Public
Affairs Dept.05A, Battetymarch
Plaza, Quincy, MA 02269.
AC Power Check
If the yellow AC light on the Fire
Supervision and Indicator Station is
off, the Control Center is not receiv-
ing AC power. Press the spring-
SILENCE
&
FIRE RESET switch
once again to turn off the Mini-
Sounder.
loaded SILENCE
&
FIRE RESET
switch to shut off the Mini-Sounder.
Check lights to see if there is a
If there is no Fire Supervision and Indicator Station on your Control
Center and your Fire Zone uses smoke detectors, have your alarm specialist
show you and explain the switch he has installed for resetting the smoke
detectors after an alarm.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Even with the most advanced fire
alarm system, adequate protection
requires an escape plan. To pre-
pare your plan:
Draw floorplans of your building.
Show two exits a front or back door
-
and a window from each room. (Make
sure the window works. You may
need a special fire escape ladder if
the window is high up.) Write down
your outside meeting place.
Family Rehearsal
Rehearse each of the following
activities:
1) Everyone in their room with the
doors closed.
2) One person sound the alarm.
Read Carefully
IMPORTANT
Discuss these escape procedures
-
cautiously. Be ready to slam the door
if smoke or heat rush in. Crawl
with those who use the building.
through smoke, holding your breath.
Close the doors again on leaving to
helppreventthefirefromspreading
4) Go to your specific outdoor
meeting place so you can see that
everyone is safe.
5) Assign someone to make sure
nobody returns to the burning build-
ing.
1
)
In a residence, sleep with the
bedroom doorclosed. A closed door
will hold back deadly smoke while
you escape.
Each person tests his door.
Pretend the door is hot and use
the alternate escape exit.
Everyone meet outdoors at the
assigned spot.
3)
4)
2) When thefirealarm signals, es-
cape quickly. Do not stop to pack
5)
3)
Test the door. If it is hot, use
your alternate route through the
window. If the door is cool, brace
your shoulder against it and open it
6) Call the fire department from a
neighbor’s telephone.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Contacts
Zone Features
Area Protected
Zone
(doom, wlndows, etc.)
1
6
Central Station
Telephone
Telephone
(Optional)
Service Person
15
Download from Www.Somanuals.com. All Manuals Search And Download.
|