Operating instructions
for condenser tumble dryer
T 4423 C
G
To avoid the risk of accidents or
damage to the machine it is
essential to read these operating instructions
before it is installed or used for the first time.
M.-Nr. 06 067 760
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Cleaning the condenser unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Removing the condenser unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Checking the condenser unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Cleaning the condenser unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Replacing the condenser unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Problem solving guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
General problems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Check and fault indicator lamps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Check and fault indicator messages in the display . . . . . . . . . . . . . . . . . . . . . 32
To change the interior drum
lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
After sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Future updates (PC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Optional accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Front view. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Installation site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Transporting the machine to its installation site . . . . . . . . . . . . . . . . . . . . . . . . 36
Building under a continous worktop / in a row of kitchen units . . . . . . . . . . . . 36
Replacing the lid. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Aligning the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Room in which the dryer is located . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Washer - dryer stack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Before moving the machine again (e.g. when moving house). . . . . . . . . . . . . 37
External condensed water outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Pulling out the drain hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Connection to a sink drain outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
If you no longer wish to use an external condensed water outlet . . . . . . . . . . 39
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Electrical connection U.K. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Consumption data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Programmable functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Increased drying level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Before connecting the machine,
ensure that the connection data on
the data plate (fusing, voltage and
frequency) matches the mains
electricity supply. If in any doubt,
consult a qualified electrician.
To avoid the risk of accidents and
damage to the machine please read
these instructions carefully before
using it for the first time. They
contain important information on its
safety, use and maintenance.
Keep these operating instructions in
a safe place and ensure that new
users are familiar with the content.
Pass them on to any future owner of
the machine.
The electrical safety of this
machine can only be guaranteed
when continuity is complete between
the machine and an effective earthing
system which complies with local and
national regulations. It is most important
that this basic safety requirement is
regularly tested, and where there is any
doubt the household wiring system
should be inspected by a qualified
electrician. The manufacturer cannot be
held liable for the consequences of an
inadequate earthing system (e.g.
electric shock).
Correct use
The tumble dryer is only intended
for drying fabrics which have been
washed in a water solution, marked on
the manufacturer's wash care label as
being suitable for tumble drying.
"Dry Cleaning Kits" for freshening up
garments in a tumble dryer are
increasingly available on the market. If
using, do so at your own risk and follow
the instructions provided on the
packaging.
Do not connect the machine to the
mains electricity supply by an
extension lead. Extension leads do not
guarantee the required safety of the
machine (e.g. danger or overheating).
Any other applications may be
dangerous. The manufacturer is not
liable for damage resulting from
improper use or operation.
The machine is built in accordance
with current safety requirements.
Unauthorised repairs could result in
unforeseen dangers for the user, for
which the manufacturer cannot accept
liability. Repairs should only be
undertaken by a Miele approved
technician.
This machine is not a toy! To avoid
the risk of injury, do not allow
children to play on or near it, or to
play with the controls. Supervise its
use by the elderly or infirm.
Ensure current is not supplied to the
machine while maintenance or repair
work is being carried out.
Technical safety
Faulty components must only be
exchanged for Miele original spare
parts. Only when these parts are fitted
can the safety standards of the
machine be guaranteed.
Before setting up the machine
check it for any externally visible
damage. Do not install or use a
damaged machine.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
If the connection cable is faulty it
condensed water is allowed to freeze in
the pump, hoses and / or condensed
water container.
must only be replaced by a Miele
approved service technician to protect
the user from danger.
If the water is drained externally
through the drain hose instead of
being collected in the condensed water
container, make sure the drain hose is
securely attached if you hang it in a
sink or basin to avoid the hose slipping
and the water causing damage.
In the event of a fault or for
cleaning purposes, the machine is
only completely isolated from the
electiricty supply when:
– it is switched off at the wall socket
and the plug is withdrawn, or
Condensed water is not drinking
water. It can cause health
problems in both people and animals.
– it is switched off at the mains, or
– the mains fuse is withdrawn.
Always keep the area around the
machine free of dust and fluff. Dust
drawn into the machine can, over time,
cause blockages in the condenser unit.
Operation
This equipment is not designed for
maritime use or for use in mobile
installations such as caravans, aircraft
etc. However it may be suitable for
such usage subject to a risk
assessment of the installation being
carried out by a suitably qualified
engineer.
The dryer must not be used without
the fluff filters in place or if the fluff
filters are damaged in any way.
The fluff filters must be thoroughly
dried after cleaning. If they are still
damp or wet when replaced there is a
risk of faults occurring when the
machine is used.
The dryer must not be used without
the condenser unit in place.
Do not install the machine in a
room where the temperature may
drop down to or below freezing. At very
cold temperatures the machine may be
difficult to start.
There is a risk of damage if the
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Always close the door after use.
This way you will avoid the danger
Using accessories
Accessory parts may only be fitted
when expressly approved by Miele.
If other parts are used, guarantee,
performance and product liability
claims may be invalidated.
of:
– children climbing onto or into the
dryer or hiding things in it.
– pets or other small animals climbing
into it.
The manufacturer cannot be held
liable for damage caused by
non-compliance with these Warning
and Safety instructions.
Do not let anyone sit or lean on the
door, as this can cause the
machine to tip up.
There is danger of fire with fabrics
which:
– contain a large proportion of rubber,
foam rubber or rubber like materials.
– have been treated with inflammable
cleaning agents.
– have been splashed with hair
lacquer, hair spray, nail varnish
remover or similar substances.
– contain padding or fillings (e.g.
pillows, jackets). If these were
damaged the filling could leak out
with the risk of igniting in the dryer.
– are soiled with oil or grease.
In countries where there are areas
which may be subject to infestation
by cockroaches or other vermin, pay
particular attention to keeping the
machine and its surroundings in a
clean condition at all times. Any
damage which may be caused by
cockroaches or other vermin will not
be covered by the machine
guarantee.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring for the environment
Disposal of the packing
material
Energy saving tips
^ Make sure that your laundry is
thoroughly spun before drying.
The transport and protective packing
has been selected from materials which
are environmentally friendly for disposal
and can normally be recycled.
The higher the spin, the greater the
savings that can be made in energy
and time during drying.
Ensure that any plastic wrappings,
bags etc. are disposed of safely and
kept out of the reach of babies and
young children. Danger of suffocation!
^ Load according to the optimum
amount of laundry recommended for
the programme being used (see
Programme chart).
Rather than just throwing these
materials away, please ensure they are
offered for recycling.
Underloading is uneconomical.
Overloading gives a poorer quality of
drying and may cause unnecessary
creasing.
Disposal of your old machine
^ To save energy and time:
Old machines contain materials which
can be reclaimed or recycled. Please
contact your dealer, your local waste
collection centre or scrap merchant
about potential recycling schemes.
– Make sure the room in which the
dryer is located is well ventilated.
– Make sure the fluff filters are clean
before using the dryer.
Ensure that the machine presents no
danger to children while being stored
for disposal.
Before throwing an old machine
away unplug it and render the plug
useless. Cut off the cable directly
behind the machine to prevent misuse.
This should be done by a competent
person.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the appliance
Control panel / Features
aDelay Start button
fProgramme selector
The start of a programme can be
delayed by up to 24 hours.
The programme selector can be
turned clockwise or anti-clockwise.
The light ring around the programme
selector comes on during a pro-
gramme and goes out a few minutes
after it has ended to save energy. It
will go out a few minutes after
switching on the dryer if a
programme has not been selected or
if the programme selected is not
started.
bStart button
Press the Start button to start a
programme.
The indicator lamp will flash to
indicate that a programme can be
started. It lights up constantly once
the programme has started.
cDisplay
The display fulfills several functions.
See next page for details.
gProgramme sequence indicator
lamps: show the drying stage
reached;
Check lamps: see "Problem solving
guide" for details.
hI-On/0-Off button
For switching the machine on and off
or to interrupt a programme.
iDoor button
dAdditional option buttons
Indicator lamps:
on = option selected
off = option not selected
See "How to dry correctly - selecting
additional options" for details on
these options.
To open the door / cancel a
programme.
e Timed drying button
To select the time required for timed
drying with hot or cold air (max. 2
hours).
Pressing this button will open the
door even when the machine is
switched off at the mains.
To save energy, the interior drum
lighting will go out after a while if the
dryer is switched on and the door is
left open.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the appliance
Display
flashing bars in front of it, this indicates
that the programme is about to enter
the cooling down phase and is not
indicative of a fault.
The display shows a variety of func-
tions:
– it displays how long a programme
has to run in hours and minutes;
The time remaining displayed should
not be taken as an accurate time
– with "Delay start" it displays the time
measurement. It is an estimate of when
remaining until the programme starts; your laundry should reach the level
dryness you have selected.
– it displays programmable functions
being selected and de-selected.
Future updates
Time left display for Cottons and
Minimum Iron programmes
The indicator lamp marked "PC" is
explained in "After Sales Service".
Once a sensor programme has started
the time left for a programme to run will
be calculated by the machine. During
this calculation period the following
bars will flash in the display:
Electronic lock and programmable
functions
Electronic lock
Prevents the machine being operated
=== ... -== ... == ... . After approx. 1
minute the programme duration will
appear in the display and proceed to
count down in minutes.
by others.
Programmable functions
Programmable functions enable the
machine to be adapted to suit personal
requirements.
The programme duration can vary each
time a programme is run because it is
affected by a variety of factors e.g:
See the relevant section for detailed
instructions.
– the moisture content after spinning
– the type of textiles
– the quantity of laundry in the drum
– the ambient room temperature
– fluctuations in the electricity supply
The electronic unit adapts to each
individual load of laundry. The time
remaining for a programme to run
shown in the display is calculated
constantly during a programme. This
means that the time displayed may
fluctuate during the programme. If the
time remaining in the display has
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes on laundry care
Wash care labels
Items filled with down.
The fabric lining on these garments
may shrink depending on the quality.
They can be partially dried using the
Smoothing programme.
Before drying check the drying
symbol on the wash care label.
Significance of symbols:
Pure linen should only be machine
dried if specified as suitable by the
manufacturer on the wash care label,
as the surface of the fabric may
otherwise "roughen". These items can
be partially dried using the Smoothing
programme.
q Dry at normal temperature
r Dry at low temperature
sDo not tumble dry
If no symbol is featured, dry at your
own risk applying the following
principles:
Woven and loopknit materials (e.g.
T-shirts, knitted garments) have a
tendency to shrink, depending on their
quality and this is made worse by
over-drying. When purchasing these
garments it is advisable to take their
shrinkage properties into account.
Cotton and minimum iron items should
be dried using the appropriate
programme for the degree of drying
required. See programme chart.
For delicates and fabrics with the
following wash care label r dry using
the Low temperature option.
Minimum iron fabrics and 100% cotton
shirts or blouses tend to crease more,
the larger the load being dried,
particulary when the weave of the
fabric is very fine. Reduce the load or
use the MINIMUM IRON - Hand iron
programme with a max. load of 1 kg. If
this is unsatisfactory use the Special
care "Smoothing" setting, then hang the
garments on a hanger to dry.
Never overload the drum. Do not
exceed the maximum recommended
loads given in the "Programme
chart". Overloading can cause
unnecessary wear and tear to the
laundry, give a disappointing drying
result and cause more creasing.
Do not put soaking wet items into
the tumble dryer. Spin them
thoroughly after washing using the
appropriate spin speed.
Starched laundry can be dried in the
tumble dryer. In order to achieve the
usual finish, double the amount of
starch should be used.
New dark coloured garments should be
dried separately from light coloured
garments to avoid the danger of col-
ours running.
Tips on drying
Woollens and wool blends tend to
become matted and shrink if dried in a
tumble dryer. They can, however, be
partially dried using the Woollens hand
care programme.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Programme chart
Special notes
Programmes
Drying levels
COTTONS
Extra dry
Fabric type
maximum load: 5 kg (1)
Multi-layered fabrics, which Do not dry jersey wear in the
would not be thoroughly
dried using the "Normal +"
programme.
Extra dry programme -
tendency to shrink.
Normal +
Normal (2)
Single and multi-layered
fabrics, e.g. mixed load of
cotton fabrics (e.g.
-
towelling, jerseywear).
Load of similar fabrics
(jersey wear, flannelette
sheets, towelling).
If laundry is still too damp,
then:
- finish drying using Timed
drying "Warm air".
- Use the"Normal +"
programme next time.
Hand iron
Hand iron rr (2)
Cotton or linen fabrics (e.g.
table linen, bedlinen,
-
If laundry is still too damp
for hand ironing, then select
"Hand iron " in the future.
starched laundry etc).
r
Machine iron
Cotton or linen fabrics,
The laundry should be rolled
including starched laundry, up to prevent it from drying
for machine ironing. out before it can be ironed.
(1) Weight of dry laundry
(2) Note for test institutes: These programmes are to be
used when testing according to EN 61121 standard
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Programme chart
Programme
Fabric type
Special notes
Drying levels
MINIMUM IRON
maximum load: 2.5 kg (1)
Normal +
Minimum iron items which are Spin minimum iron fabrics for
made of synthetic or blended
fabrics (e.g. pullovers,
dresses, trousers) which are
not dried adequately in the
"Normal" programme.
at least 30 seconds in the
washing machine before
drying.
Normal (2)
Hand iron
Minimum iron shirts, table
cloths etc. made of blended
fabrics (e.g.
Spin minimum iron fabrics for
at least 30 seconds in the
washing machine before
drying.
cotton/synthetics).
Minimum iron shirts, table
cloths etc. made of blended
fabrics (e.g. cottons and
Spin minimum iron fabrics for
at least 30 seconds in the
washing machine before
synthetics), which are still to drying. For extra special care
be hand ironed.
of delicate fabrics and to
reduce creasing even more,
reduce the load to 1 kg. See
also "Special care
programmes")
TIMED DRYING
Warm air
maximum load: 5 kg (1)
Individual items
(e.g. bathing costumes, bath
towels, tea-towels).
-
Multi-layered fabric whose
layers have different drying
characteristics.
Cool air
Items which are to be aired
only.
-
(1) Weight of dry laundry
(2) Note for test institutes: These programmes are to be
used when testing according to EN 61121 standard.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Programme chart
Special notes
Programme
Fabric type
Special care programmes
Woollens
hand care
maximum load: 2 kg (1)
Woollen fabrics
To refresh and fluff up woollen
garments quickly. Remove garments
immediately at the end of the
programme. Do not repeat.
Woollen fabrics are not dried
completely by this programme.
Smoothing
maximum load: 2.5 kg (1)
Cottons and linen fabrics. Smooths out creasing caused during
Minimum iron items made
of cotton, blended fabrics
or synthetics, e.g. cotton
trousers, shirts.
the spin cycle in the washing
machine.
Fabrics are not completely dried in
this programme.
Remove garments immediately at
the end of the programme and place
on a line or hangers to dry.
(1) Weight of dry laundry
Selecting additional options
Programme
Additional option button(s)
COTTONS
Anti-crease, Short, Low temperature, Buzzer
MINIMUM IRON
TIMED DRYING - Warm air
- Cool air
Woollens hand care
Smoothing
Anti-crease, Short, Low temperature, Buzzer
Anti-crease, Low temperature, Buzzer
Buzzer
Buzzer
Buzzer
For delicates and fabrics with the following wash care label r select the Low
temperature option.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
How to dry correctly
A Prepare the laundry
Do not overload the drum.
^ As far as possible, sort laundry for:
- the type of fibre or weave,
- the degree of dryness required,
- similar size of items,
Overloading can cause unnecessary
wear and tear to the laundry and
give a disappointing drying result.
- the moisture content after
spinning.
This will help towards achieving an
even drying result.
See the "Programme chart" for
maximum recommended loads.
^ Before closing the door check that
the fluff filter is correctly positioned in
the door.
Fasten duvet covers etc. to prevent
small items from being rolled up inside
them.
Do up zips, hooks and eyes etc.
Tie fabric belts, apron strings.
Sew in or remove underwiring from
bras.
Make sure there is no detergent
dispenser ball etc. in with the
laundry, as this could melt and
damage the machine and the
laundry.
B Load the drum and switch
on the dryer
When closing the door make sure
items of laundry cannot be trapped
by the door, as this will cause
damage to the laundry.
^ Press the door button and open the
door.
^ Shut the door either with a gentle
swing or lean against it and push it
shut.
^ Load the laundry loosely into the
drum.
^ Switch the dryer on by pressing the
"l-On/0-Off" button.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
How to dry correctly
C Selecting a programme
D Selecting additional options
^ Turn the programme selector to the
programme required.
^ Additional options are selected
before starting a programme by
pressing the relevant buttons.
COTTONS and MINIMUM IRON
The length of the programme is
electronically calculated according to
the residual moisture content of the
load. Approx. drying times are given in
the "Consumption data" chart.
It is not possible to activate additional
options which are incompatible with the
drying programme selected. The
indicator light will go out when the
option button is released. If an
inappropriate combination of options is
selected (e.g. "Short" and "Low
temperature") only the last option
selected will be activated.
Woollens Hand care and Smoothing
See the "Consumption data" chart for
programme times.
TIMED DRYING
Anti-crease
When choosing Warm or Cool air
TIMED DRYING you select the duration
of the programme.
By selecting the anti-crease option
the drum will turn at regular intervals
after the end of the programme to
prevent the laundry from settling into
creases and folds.
^ Press the Timed drying button
repeatedly until the required time
appears in the display.
Times are chosen as follows:
- 15-30 minutes in 5 minute stages
- Over 30 minutes in 10 minute
stages.
If the Timed drying button is held
pressed in, the time will automatically
run up to 2 hours and then go back
to i5 minutes again.
The anti-crease option
^ should be selected if laundry is not
going to be removed from the drum
as soon as the programme has
finished.
^ can be selected or de-selected after
a programme has started.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
How to dry correctly
Short
E Delay start
For drying fabrics which can
Once a programme has been
withstand high temperatures, e.g.
pure linens and cottons. Do not use
on minimum iron or delicate fabrics.
selected, the start can be delayed by
30 minutes (30) up to 24 hours (24^).
– Because the heater rating is
increased clothes dry faster thus
shortening drying times.
Low temperature
For drying delicate fabrics with the
symbol r (e.g. acrylic garments) at a
lower temperature.
^ Press the Delay start button
repeatedly until the required time
appears in the display :
- up to 10^ in 30 minute stages.
- over 10^ in 1 hour stages.
The time will run up to 24^ by
keeping the button pressed in.
Because the heater rating is reduced
clothes dry more slowly thus
lengthening drying times.
Press the Start button. The chosen time
will count down as follows:
Buzzer
An audible tone sounds repeatedly at
the end of a programme.
– from 24^ to 10^ in 1 hour stages.
– less than 10^ in 1 minute stages.
^ The buzzer can be switched on or off
after a programme has started.
The dryer starts automatically once the
delay start period has elapsed. The
time left will appear in the display
The volume (and pitch) of the buzzer
can be adjusted before a programme is approx. 1 minute into the programme.
started:
To cancel "Delay start":
^ Select the programme.
Before the Start button has been
pressed:
^ Press the "Buzzer" button (the
"Buzzer" indicator lamp will light up)
until the desired volume / pitch is
achieved. Then release the button.
^ Press the Delay start button once
when 24^ is showing in the display;
After the Start button has been
pressed:
^ Turn the programme selector to the
Finish position.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
How to dry correctly
F Starting a programme
^ Press the Start button.
^ The condenser unit should be
checked an cleaned on a regular
basis.
The drying cycle begins.
See "Cleaning and Care".
The drying stage reached is shown by
the sequence indicator lamps on the
right hand side of the control panel.
^ After each use, switch the dryer off
by pressing the l-On / 0-Off button.
^ Always close the door after use.
At the end of the drying phase, a
cooling down phase commences to
cool the laundry down (the Cool air
indicator lamp lights up).
Additional notes
. . . Clean out airways indicator lamp
The drying level required has now been
reached.
This indicator lamp comes on to warn
you that the dryer is not working
efficiently.
G After drying
This may be because:
The Anti-crease/Finish and the drying
stage reached indicator lamps light up. – the fluff filters are clogged;
The buzzer will sound at intervals
– the condenser unit is clogged.
during the anti-crease phase if it has
been selected.
0 will then appear in the display.
^ Press the Door button to open the
drum door.
^ Remove the laundry.
Make sure that the drum is empty. If
items are left in the dryer, they could
be damaged by overdrying when
the dryer is next used.
^ After every cycle remove the fluff
from the fluff filter in the door and in
the door opening (see "Cleaning and
Care").
^ Empty the condensed water
container (where there is no external
drainage of the water).
17
Download from Www.Somanuals.com. All Manuals Search And Download.
How to dry correctly
Brief instructions
F Start the programme
These instructions are designed as a
brief guide only. Please make sure that
you also read the detailed instructions
at the beginning of this section.
^ Press the Start button
G At the end of a programme
– The Anti-crease / Finish indicator
lights up.
A Sort the laundry
– 0 appears in the display.
B Load the dryer and switch it on
^ Open the door and remove the
laundry.
^ Press the Door button to open the
door.
^ Press the l-On/0-Off button to switch
the machine off and close the door.
^ Load the drum.
^ Close the door.
^ Switch the dryer on by pressing the
l-On/0-Off button.
C Select a programme
^ Turn the programme selector to the
required programme.
For TIMED DRYING (warm or cool air):
^ Press the Timed drying button
repeatedly until the required drying
time shows in the display.
Points D and E are optional.
D Select any additional options as
required
^ Press the relevant button for the
additional option(s) required.
E Select Delay start
^ Press the Delay start button
repeatedly until the required delay
period shows in the display.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
How to dry correctly
To change a programme
^ Press the Start button.
Programmes cannot be changed after
the start button has been pressed. If
the programme selector is turned to a
different programme after a programme
has begun, this will not affect the
programme. The Anti-crease / Finish
indicator lamp will flash. The indicator
lamp will go out when the selector is
returned to its original position.
Adding or removing items
^ Press the Door button and open the
door.
,Do not touch the back of the
drum when adding or removing
items. The drum could be very hot -
danger of burning.
After a programme has started, not all
additional options can be switched on
or off (see section "How to dry
correctly").
^ Items can now be added or removed
early.
To continue drying:
^ Close the door.
To interrupt a programme
^ Switch additional options on or off as
required.
^ Switch the machine off with the
I-On / 0-Off button.
^ Press the Start button.
To continue drying:
– The programme will continue.
^ Switch the dryer on with the
– The time left shown in the display
may now vary from the actual drying
time.
I-On / 0-Off button.
The programme will continue, as long
as the cooling down phase has not
been reached.
To cancel a programme and select a
different programme
^ Turn the programme selector to
Finish.
The programme has been
successfully cancelled when only the
Anti-crease/Finish indicator lamp is
on.
^ Turn the programme selector to the
required programme.
^ Switch additional options on or off as
required.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Electronic system lock
To de-activate the system lock
The system lock prevents anyone
from interfering with the dryer.
^ Repeat steps A-G.
The Locked indicator lamp will go out
after step F.
If the system lock has been activated it
is not possible to start a programme.
The following steps (A,B,C...) must
be carried out in the correct order.
Please proceed step by step:
To activate the system lock
AEnsure that the door is closed and
that the programme selector is
turned to Finish.
BSwitch on the dryer with the
I-On/O-Off button.
CPress the Anti-crease button and
keep it pressed in while carrying out
steps D to F.
DSlowly turn the programme selector
clockwise stage by stage until it
reaches the COTTONS/Normal
position.
ESlowly turn the programme selector
anti-clockwise stage by stage until it
reaches the Finish position.
FSlowly turn the programme selector
anti-clockwise stage by stage until it
reaches the MINIMUM IRON/Hand
iron position.
The Locked indicator lamp will flash.
GRelease the Anti-crease button.
The system lock is now activated.
HSwitch off the dryer with the
I-On/O-Off button.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Emptying the condensed
water container
The condensed water will be collected
in the condensed water container
unless the machine has been fitted with
a drain hose (see installation).
The condensed water container
should be emptied after every
drying cycle or as soon as the
Empty out container indicator lamp
comes on.
The drying programme will be
^ Open the shutter and empty out the
water.
interrupted if the maximum level of the
condensed water container is reached.
The Empty out container indicator lamp
comes on and the buzzer sounds.
^ To replace the container hold it at a
slight angle (as when removing it)
and push it in gently until you feel it
click into position.
^ Before starting a new programme,
first switch the machine off and then
on again. The Empty out container
indicator lamp will go out.
Condensed water should not be
consumed. It could lead to health
problems for people and animals.
Condensed water can be put to
household use (e.g. used in a steam
iron or humidifier). To ensure that any
residual particles of fluff in the
condensed water are removed before
use, pass it through a fine sieve or
paper filter first.
^ Grip the container firmly with both
hands, as shown, and pull it out
slightly towards the right-hand side.
^ Hold the container with both hands
and carry it in a horizontal position.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Cleaning the fluff filters
^ Remove any fluff from the hollow part
of the door holder. A cleaning brush
is available as an optional extra from
your Miele dealer or the Miele Spare
Parts Department.
The fluff which is created by the drying
process is collected by the fluff filters in
the door and the door opening. Clean
the filters after each drying programme.
Tip: You can also use a vacuum
cleaner.
Cleaning them whilst dry
^ Once clean, push the filter back into
the door holder until it clicks into
position. Ensure it is facing the
correct way.
^ Open the door and pull the fluff filter
out of the door as illustrated.
^ Use your fingers to remove the fluff
from the two fluff filters in the door
opening.
^ Close the door.
^ Use your fingers to remove the fluff
from the surface of the filter.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Cleaning them with water
^ Place the filters back in the door
opening (the left and right filters are
identical) with the finger holders
facing upwards. See illustration.
If there is a great deal of compacted
fluff on any of the filters, they can be
removed and cleaned under hot
running water.
Cleaning the tumble dryer
^ To remove the fluff filter from the door
holder see previous page.
Disconnect the machine from the
mains electricity supply.
^ Clean the housing and control panel
with a slightly damp cloth and a mild
detergent or soapy water.
^ The drum and other stainless steel
parts can be cleaned with a suitable
proprietary stainless steel cleaner
following the manufacturer's
instructions.
Do not use solvents, abrasive
cleaners, glass cleaners or
all-purpose cleaners. These could
damage plastic sufaces and other
parts. The machine must never be
hosed down.
^ To remove the filters in the door
opening, grip the holder and push
upwards in the direction of the arrow
to remove it.
^ Dry all parts with a soft cloth.
^ Rinse the filters under hot, running
water.
^ A microfibre E-Cloth is available from
the Miele UK Spare Parts Department
which is suitable for cleaning
surfaces such as stainless steel,
glass, plastic and chrome without the
use of chemicals. It can be washed
300 times.
^ Then shake the filters until no more
water droplets are visible.
^ Dry the filters thoroughly with care.
,Do not replace them if they are
damp or wet. Damp or wet filters
could cause operational faults.
^ Push the large filter back into the
door holder until it clicks into position.
Ensure it is facing the correct way.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Cleaning the condenser unit
Detergent residue, hair and fine fluff
from the dryer can get through the fluff
filters and block the condenser unit.
Dust from the room in which the dryer is
installed can also get into the
condenser unit and cause a blockage.
Check the condenser unit at least
twice a year. If the dryer is used
frequently then clean the condenser
unit after approx. 100 drying cycles.
^ Turn the lever on the inner cover
downwards to the vertical position.
Removing the condenser unit
^ Pull the cover forwards
^ Then remove it by pulling it
diagonally upwards.
^ Open the service panel by pressing
the two lower corners at the same
time (see illustration).
The hooks at the side will prevent the
panel from falling off.
^ Turn the lever on the condenser unit
to the vertical position.
^ Now the remove the panel by pulling
it diagonally upwards.
^ Then place it to one side.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
If you cannot see any fluff:
^ Replace the condenser unit (see
following page).
If you can see some fluff:
^ Clean the condenser unit as
described below.
Cleaning the condenser unit
^ When rinsing the condenser unit,
make sure you position it as shown in
the next two illustrations.
^ Pull the condenser unit out of its
housing by the handle.
Checking the condenser unit
^ Use a shower head or similar to rinse
the unit out as shown.
^ Hold the condenser unit up to the
light as shown.
^ Check to see if there is any fluff
inside it.
The arrows in the illustration above
indicate where to look.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Replacing the condenser unit
^ With the handle facing upwards,
push the condenser unit back into
position in its housing.
^ Turn the lever down to the horizontal
position, making sure that the hook
on the lever clicks into the groove.
When replacing the inner cover after
cleaning, ensure that the rubber seal
fits correctly into the groove.
^ Replace the cover making sure the
hooks locate correctly. Hold it at an
angle and push it gently downwards.
^ Then flush the unit through from the
front.
^ Check the condenser unit again for
any visible fluff and if necessary flush
it through again until it has all gone.
^ Then turn the lever upwards into the
horizontal position to lock the cover.
^ Replace the service panel and press
the upper edge until it clicks into
position.
^ Remove any soiling still visible inside
the housing unit.
^ Also make sure the rubber seals are
clean.
It is important to ensure that both the
condenser unit and the cover are
correctly positioned and locked.
Otherwise water may leak from the
machine.
The rubber seals must not be
removed and must be free of kinks.
^ Shake any excess water out of the
unit until no more water droplets are
visible.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
With the help of the following notes minor faults in the performance of the
machine, some of which may result from incorrect operation, can be put right
without contacting the Service Department.
,Repair work to electrical equipment should only be carried out by a suitably
qualified person in accordance with local and national safety regulations.
Repairs and other work by unqualified persons could be dangerous. The
manufacturer cannot be held liable for unauthorised work.
General problems
Problem
Possible cause
Remedy
The tumble dryer fails to No obvious cause.
start when switched on.
– Have you followed the
switch-on procedure
correctly (see “How to
dry correctly”)?
– Is the plug correctly
inserted in the socket
and switched on?
– Is the door closed
properly?
– Has the fuse or circuit
breaker tripped?
Items made of synthetic Synthetic fibres tend to
fibres are charged with attract static charge.
static electricity after
Static charge can be
reduced by adding a
fabric conditioner to the
final rinse in the washing
machine or a fabric
drying.
conditioner sheet to the
load in the dryer.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
Problem
Possible cause
Remedy
There is a build up
of fluff.
Fluff is principally the result Fluff is collected by the fluff
of friction when garments
are being worn and
filters and can be easily
removed (see "Cleaning
and Care").
washed. Machine drying
hardly causes any fluff to
form and has been
established by research
institutes to have no effect
on the lifetime of fabric.
The laundry is not
sufficiently dry.
The load consisted of
different fabrics.
– Finish drying using
"Timed drying - Warm
air".
– Select a more suitable
drying programme next
time (see "Programme
chart").
There are water
A double filter system with Laundry being removed
droplets at the upper dual insulation prevents fluff from the machine may
edge of the drum
aperture.
from being deposited in the come into contact with
condenser unit. This
these water droplets, but
they will dry off in a matter
of minutes.
insulation can lead to a
build-up of condensation.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
Problem
Possible cause
Remedy
The drying process Important: Before attempting to remedy one of the
goes on too long or following causes, switch the dryer off and switch on again
even switches off. to start the programme again.
Ventilation to and from the
dryer may be insufficient
Open a door or window
while the machine is in
(e.g because it is installed in operation for increased air
a small room). This has
caused the temperature in
the room to rise sharply.
flow.
The fluff filters are clogged
up with fluff or were still wet
when they were replaced.
– Remove any fluff.
– The fluff filters must be
completely dry.
The laundry has not been
spun sufficiently.
Make sure that your laundry
is thoroughly spun at
highest spin speed for the
type of fabric.
The tumble dryer has been Do not exceed the maximum
overloaded.
load for the programme
selected.
Metallic components, e.g.
zips have prevented the
dryer from registering the
correct moisture level in the
laundry.
– Close zips and fasten any
hooks next time.
If the problem occurs again,
dry garments with long zips
using "Timed drying - Warm
air".
Detergent residues, hair and Check the condenser unit
fine fibres can block up the from time to time and clean
condenser unit.
it if necessary (see
"Cleaning and Care").
The vents below the door
are blocked.
Remove any objects that are
blocking the vents.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
Problem
Possible cause
Remedy
The condenser unit The inner cover of the
– Ensure that the condenser
unit is positioned correctly
and lock the cover.
service panel will
not shut.
condenser unit has not
been locked properly
and/or the condenser unit
has not been positioned
correctly.
– Check the rubber seals.
Water leaks from the Fluff has collected at the
machine after the bottom of the condenser
condenser unit has unit housing.
– Use a cloth to remove any
fluff from the inside of the
condenser unit housing.
been cleaned.
The interior drum
lighting does not
come on.
The lighting switched off
automatically.
The lighting only comes on
when the door is opened if
the dryer is switched on. To
save energy the lighting
goes out after a while if the
door is left open.
The lamp needs changing. Change the lamp as
described at the end of this
section.
The ring around the The lighting switched off
programme selector automatically.
does not light up.
It lights up when drying is in
progress and goes out
shortly after the end of the
programme to save energy.
Check and fault indicator lamps
Problem
Possible cause
Remedy
The Anti-crease /
Finish indicator
lamp flashes while
drying is in
The programme selector
was moved after the start original position and the
of a programme. The
programme continues to
run as normal.
Turn the selector back to the
indicator lamp will go out.
progress.
The Locked
The system lock is
activated.
If you wish to use the dryer,
the system lock must be
deactivated (see "Electronic
system lock").
indicator lamp
flashes when the
machine is switched
on and the
programme cannot
be started.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
Problem
Possible cause
Remedy
The Clean out
airways lamp comes blocked.
The fluff filters may be
Remove any fluff (see
"Cleaning and care").
on.
The condenser unit may be Please note that the
blocked with fluff and
detergent residues.
condenser unit must be
cleaned regularly (see
"Cleaning and care").
The check lamp will go out
when the door is opened.
The programme
Possible causes and remedies are described above in
stops and the Clean (The Clean out airways lamp comes on).
out airways lamp
flashes.
There is no obvious cause. – Switch off the dryer.
– Then switch the dryer
back on and start the
programme again.
If the programme stops
again and the Clean out
airways lamp flashes, there
is a fault. Contact the Miele
Service Department.
The Empty out
container indicator
lamp comes on.
The condensed water
container is full or there is
kink in the drain hose.
– Empty out the
condensed water
container.
– Check the drain hose.
– Before starting a new
programme, first switch
the dryer off and then on
again.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
Problem
Possible cause
Remedy
The programme has No obvious cause.
been interrupted,
– Switch the dryer off and
then on again.
the indicator lamp
for Hand iron or
Machine iron is
flashing, and the
buzzer sounds.
– Then start the programme
again.
If the programme stops
again and an indicator lamp
flashes, there is a fault.
Contact the Miele Service
Department.
Check and fault indicator messages in the display
After the beginning This is not a fault.
of the programme
the following
symbols flash in the
display: "=== ... -== ...
== ... ".
The electronic unit is
calculating the drying time
for the programme (see
“Guide to the appliance”).
Shortly before the
end of the
This might be because:
– items of laundry may
The drying process is not
yet complete. The
programme, the
count down of the
time left to run halts
at 11 or 6, horizontal
bars flash but the
dryer continues to
dry.
programme needs more
time than the electronic unit
calculated at the start of the
programme. The time count
down is suspended until the
degree of drying selected
has been reached.
have rolled up together.
– the types of fabrics being
dried may take different
times to dry.
– the fluff filters are
clogged.
– the temperature in the
room may have
changed.
The programme has This is not a fault. The
Use the "Timed drying -
been stopped, the
Anti-crease/Finish
lamp comes on, 0
appears in the
display and the
buzzer sounds.
electronic unit has
recognised that there is no individual items.
laundry in the drum and
cancelled the programme.
Drying individual garments close the drum door.
or items which are already
Warm air" programme to dry
Before changing a
programme: Open and
dry can also cause the
programme to be stopped.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
To change the interior drum
lamp
^ To close the flap push it upwards and
press it on the left and right until you
hear it click into position.
^ Open the door.
The cover must be fixed securely, as
otherwise moisture may seep in and
cause a short circuit.
Before changing the lamp,
disconnect the machine from the
mains power supply.
You will find the interior lamp cover at
the top of the drum aperture.
^ Insert the opener under the side
edge of the cover as illustrated.
^ Turn your wrist to make the cover
open downwards.
The temperature resistant lamp should
only be ordered from your Miele dealer
or the Miele Spare Parts Department.
The lamp must not exceed the
maximum wattage quoted on the
data plate and on the lamp cover.
^ Replace the lamp.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
After sales service
Repairs
Future updates (PC)
In the event of any faults which you
The indicator or check lamp marked PC
cannot remedy yourself, please contact on the fascia panel is the interface
used by the Miele service technicians
during service work for testing
– Your Miele Dealer or
– The nearest Miele Service
Department (see back cover for
address).
purposes and for updating the
machine's programme data.
Optional accessories
When contacting the Service
Department, please quote the Model
and Serial numbers both of which are
located on the data plate situated on
the right hand side below the drum
aperture.
Optional accessories for these dryers
are available from your Miele Dealer or
from the Miele Spare Parts Department.
Please note that telephone calls may
be monitored and recorded to
improve our service.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Front view
aSupply cable for electrical
eService panel for condenser unit
connection
fFour height-adjustable screw feet
bCondensed water container
cControl panel
gExternal drainage options (e.g. via
wash basin, wash basin drain outlet,
or gully).
dDoor
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation site
A building under kit* is required
which must be fitted by a suitably
qualified person.
The machine lid is replaced by a
coverplate. It is essential that the
coverplate is fitted to ensure
electrical safety.
,Make sure the dryer door can be
opened without hindrance after
installation.
Transporting the machine to its
installation site
When moving the machine you can
hold it by the lid where it protrudes to
the rear of the dryer.
To manoeuvre the dryer out of its
packing case to its installation site you
will also need to hold it by the front feet.
– When installing under a 900/910 mm
high worktop a spacer kit* is
required.
– The electrical socket must be
located in an accessible position
near the machine.
Building under a continous worktop /
in a row of kitchen units
* Available as an optional accessory
from your Miele dealer or the Miele
Spare Parts Department.
The dryer should not be installed
next to a refrigerator or freezer. The
warm air expelled from the rear of
the dryer would increase the
temperature around the
refrigerator's/freezer's heat
exchanger causing the compressor
to run continuously.
If it is not possible to install the dryer
anywhere else, then the
refrigerator/freezer must be sealed
off from the dryer.
The building under kit is supplied with
its own installation instructions.
N.B. When built under running times
may be longer.
If you wish to push your machine under
a worktop and there is space to do this
without removing the lid, the building
under kit is not necessary. Otherwise
the building under kit is essential.
Replacing the lid
If the lid has been removed in order to
fit a cover plate, ensure that, if the lid is
replaced, it fits securely into the rear
holders. Otherwise, it is not properly
secure for transport.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Aligning the machine
Room in which the dryer is located
Air taken in for use in the drying
process will be warm when it is
expelled from the rear of the dryer. This
expelled air heats up the air in the
room. It is therefore very important to
ensure that the room is adequately
ventilated, particularly if the dryer is
located in a small room. Otherwise
running times and energy consumption
could be increased.
Washer - dryer stack
The tumble dryer can also be
combined with a Miele washing
machine in a washer-dryer stack. To do
this the appropriate stacking kit* (WTV)
to match your washing machine is
required.
The machine must be perfectly level to
ensure safe and proper operation.
* Available as an optional accessory
from your Miele dealer or the Miele
Spare Parts Department.
Stacking kits must be fitted by a
suitably qualified fitter.
Before moving the machine again
(e.g. when moving house)
After each use a small quantity of
condensed water will collect in the area
around the pump. This water can run
out if the machine is tipped up when it
is being moved. It is a good idea to run
the Cool air programme for
approximately 1 minute before moving
the machine. Any remaining
condensed water will then be fed into
the condensed water container or out
through the drain hose.
^ The screw feet can be adjusted to
compensate for any unevenness in
the floor.
,The ventilation gaps in the plinth
must not be covered over as this
would prevent a sufficient intake of
air.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
External condensed water
outlet
From the back of the dryer at the
bottom:
When drying is in progress, condensed
water is pumped into the condensed
water container through the drain hose
at the back of the dryer. The
condensed water can also be drained
off directly if the machine is installed
near a sink, drain outlet etc. so that
the condensed water container does
not have to be emptied.
The drain hose (approx. 2 m long) is
stored in the dryer. It must be pulled
out of the dryer to its full extent if
condensed water is to be drained
externally.
^ Unclip the drain hose from holder (3).
Maximum delivery head: 1 m.
^ Then pull the drain hose completely
out of the dryer towards the left (4)
(See illustration).
If it is not long enough, an extension
hose is available as an optional
accessory through your dealer or from
the Miele Spare Parts Dept.
,Important: do not let the drain
hose become kinked as this could
damage it.
Pulling out the drain hose
From the back of the dryer at the top:
,If you want to drain the water off
into a sink you will need to secure
the hose carefully, e.g. by tying it to
a tap to make sure it cannot slip
during use. Otherwise there is a risk
of overflowing water which could
cause damage.
Use the bow-shaped guide to prevent
the drain hose from becoming kinked
(see "Front view" illustration).
^ Unclip the drain hose (1).
^ Then pull it off holder (2).
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Connection to a sink drain outlet
If this nut has a flat disc sealing it you
should take the disc out first.
Important: if this nut has a washer or
seal in it this must not be removed!
The drain hose can be connected
directly to a sink drain outlet.
^ Attach the end of the hose to adapter
1.
^ Use a screwdriver to tighten hose
clip 3 up close to the nut.
If you no longer wish to use an
external condensed water outlet
,Do not push the drain hose
back into the dryer. Doing this could
cause it to become kinked and
damaged in the dryer.
^ Remove the following from the back
of the dryer at the bottom:
Adapter 1 and hose clip 3 behind it.
^ Loop the drain hose up.
^ Use a suitable cable tie to secure the
looped hose to the back of the dryer,
or simply lay the looped hose behind
the dryer.
^ Attach the open end of the drain
hose back onto the holder at the
back of the dryer at the top (see
holder 2 in "Pulling out the drain
hose").
^ Fit adapter 1 to the sink drain outlet
using nut 2.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical connection
Electrical connection U.K.
Electrical connection U.K.
Non-rewireable plugs BS 1363
All electrical work should be carried out
only by a suitably qualified and
If this machine is fitted with a
competent person, in strict accordance non-rewireable plug and the socket
with national and local safety
regulations.
outlets are not suitable for the plug
supplied or if the existing plug needs to
be replaced by a new one, the old plug
will need to be cut off and an
appropriate plug fitted. The fuse carrier
and the fuse should be removed from
the old plug and disposed of.
Ensure power is not supplied to the
machine while installation work is being
carried out.
The machine is supplied with a mains
cable with moulded plug for connection
to a 230-240V mains supply. The
voltage, rated load and fuse rating
are given on the data plate. Please
ensure these match the household
mains supply.
The plug cut from the cable should then
be disposed of and on no account be
inserted into any socket elsewhere in
the house (electric shock hazard).
The fuse cover must be refitted when
changing the fuse, and if the fuse cover
is lost, the plug must not be used until a
suitable replacement is obtained. The
colour of the correct replacement cover
is that of the coloured insert in the base
of the plug, or the colour that is
embossed in words on the base of the
plug (as applicable to the design of
plug fitted).
Connection should be made via a fused
plug and suitable switched socket
which is easily accessible after
installation.
For extra safety it is advisable to install
a residual current device (RCD), with a
trip current of 30 mA (in accordance
with DIN VDE 0664, VDE 0100, section
739).
Do not connect via an extension lead.
Replacement fuses should be ASTA
approved to BS 1362 and have the
correct rating. Replacement fuses and
fuse covers may be purchased from
your local electrical supplier.
Important
The wires in the mains lead are
coloured in accordance with the
following code:
Green/yellow = earth
Blue
= neutral
= live
Brown
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical connection
If the colours of the wires in the mains
lead of this machine do not correspond
with the coloured markings identifying
the terminals of your plug, proceed as
follows:
^ The wire which is coloured green and
yellow must be connected to the
terminal in the plug which is marked
with the letter E or by the earth
symbol z or coloured green, or
green and yellow.
^ The wire which is coloured blue must
be connected to the terminal in the
plug which is marked with the letter N
or coloured black.
^ The wire which is coloured brown
must be connected to the terminal in
the plug which is marked with the
letter L or coloured red.
WARNING: THIS APPLIANCE
MUST BE EARTHED
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumption data
Programme
Capacity
Final spin speed
(in a domestic
washing machine)
Electricity
consump-
tion
Drying time
incl.
cooling down
time
kg
rpm
kWh
Minutes
COTTONS
Extra dry
5.0
1200
1400
1600
1800
3.25
3.10
2.85
2.80
86
82
76
74
Normal +
5.0
1200
1400
1600
1800
2.80
2.65
2.40
2.35
76
73
66
65
(1)
Normal
5.0
5.0
800 (70 % residual moisture)
3.40
91
Normal
1200
1400
1600
1800
2.65
2.55
2.25
2.20
73
70
63
62
(1)
Hand iron
Hand iron
5.0
5.0
800 (70 % residual moisture)
2.75
76
1200
1400
1600
1800
2.00
1.85
1.60
1.55
58
55
48
47
Machine iron
5.0
1200
1400
1600
1800
1.60
1.45
1.20
48
45
38
37
1.15
MINIMUM IRON
(1)
Normal
2.5
2.5
1000 (50 % residual moisture)
1000
1.25
1.10
39
35
Hand iron
Special care
Woollens hand care
Smoothing
2.0
2.5
-
-
0.20
0.30
4
9
(1) EN 61121 test programme
EN 61121 Standard testing
Before testing in accordance with EN 61121, dry a 3 kg load of cotton laundry
with 70% residual moisture as per the above standard using the Normal Cottons
programme without selecting any additional functions.
Consumption data can vary from the nominal values given above depending
on the size of the load, types of textiles, residual moisture levels after spinning,
fluctuations in the electricity supply and any additional options selected.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical data
Height
85 cm (adjustable +0.7/- 0.7 cm)
Height without lid
Width
82 cm
59.5 cm
58 cm
Depth
Depth with door open
Weight
106 cm
54 kg
Drum volume
Maximum capacity
100 litres
5 kg dry weight
Capacity of condensed
water container
approx. 3.5 litres
1.60 m
Length of connection cable
Maximum delivery head
Maximum drain hose length
Voltage
1 m
3 m
see data plate
see data plate
see data plate
see data plate
see "Consumption data"
Radio/TV suppressed, VDE
Rated load
Fuse rating
Lamp wattage
Energy consumption
Test certificates awarded
43
Download from Www.Somanuals.com. All Manuals Search And Download.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Programmable functions
for changing
standard settings
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Programmable functions
Increased drying level
DTurn the programme selector to
COTTONS, Extra dry.
The Sensitive System aims to dry
using as little energy as possible.
However, if you require the laundry to
be drier, it is possible to reduce the
final moisture level in the COTTONS
and MINIMUM IRON programmes.
EThe number of the programmable
function will flash alternately with the
"P" on the left of the display -
P: P...1...P... 1... .
The number on the right will show
constantly:
0 = Increased drying level - off
1 = Increased drying level - on
The machine is delivered with this
programmable function switched off.
FPress the Start button to change the
number on the right from
0 to 1 = on or from
Programming and
storing in memory
The programmable functions are
activated to call up further features not
shown on the control panel by using the
additional option buttons in
1 to 0 = off.
The setting you have selected is now
stored in memory.
combination with the programme
selector.
GSwitch the machine off with the
I-On/0-Off button.
Before you begin, first ensure that:
– The tumble dryer is switched off.
– The door is closed.
To check:
^ Carry out steps A to E.
^ Switch off the dryer.
The check is complete.
– The programme selector is at
Finish.
APress the additional option buttons
Short and Low temperature at the
same time, hold pressed in and ...
B... switch on the dryer with the
I-On/0-Off button.
CLet go of all these buttons.
– "P" will appear in the display.
– The Drying and Cool air indicator
lights will flash.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Programmable functions
Memory
DTurn the programme selector to
COTTONS, Normal.
The additional options selected
previously for specific programmes
are stored in the machine’s memory.
EThe number of the programmable
function will flash alternately with the
"P" on the left of the display -
P: P...3...P... 3... .
The machine is delivered with this
programmable function deactivated. It
can be activated if wished.
The number on the right will show
constantly:
0 = Memory function - off
1 = Memory function - on
Programming and
storing in memory
FPress the Start button to change the
number on the right from
0 to 1 = on or from
The programmable functions are
activated to call up further features not
shown on the control panel by using the
additional option buttons in
combination with the programme
selector.
1 to 0 = off.
The setting you have selected is now
stored in memory.
GSwitch the machine off with the
Before you begin, first ensure that:
– The tumble dryer is switched off.
– The door is closed.
I-On/0-Off button.
To check:
^ Carry out steps A to E.
^ Switch off the dryer.
The check is complete.
– The programme selector is at
Finish.
APress the additional option buttons
Short and Low temperature at the
same time, hold pressed in and ...
B... switch on the dryer with the
I-On/0-Off button.
CLet go of all these buttons.
– "P" will appear in the display.
– The Drying and Cool air indicator
lights will flash.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Alteration rights reserved/0504
M.-Nr. 06 067 760 / 00
This paper consists of cellulose which has been bleached without the use of chlorine.
Download from Www.Somanuals.com. All Manuals Search And Download.
|