Macsense Connectivity Network Card HomePod User Manual

HomePod

User Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual

MP-100

HomePod — Wireless Network Digital Audio Player with FM Tuner

reserved. No part of this documentation may be reproduced in any form or by any means or

used to make any directive work (such as translation or transformation) without permission

from Xsense Connectivity, Inc. Xsense Connectivity, Inc. reserves the right to revise this

documentation and to make changes in content without obligation among Xsense

Connectivity, Inc. to provide notification of such revision or change. All products and their

associated features are subject to change or upgrade at the time of the shipment or of the

sales.

Trademarks

All products, company, brand names are trademarks or registered trademarks of their

respective companies. They are used for identification purpose only. Specifications are

subject to be changed without prior notice.

FCC Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against radio interference in a commercial environment. This

equipment can generate, use and radiate radio frequency energy and, if not installed and

used in accordance with the instructions in this manual, may cause harmful interference to

radio communications. Operation of this equipment in a residential area is likely to cause

interference, in which case the user, at his own expense, will be required to take whatever

measures are necessary to correct the interference.

Safety Precautions

Follow all warnings and instructions marked on the product.

•

Slots and openings on the device are provided for ventilation. To protect it from

overheating, these openings must not be blocked or covered.

Do not use or store HomePod in the environment that exceeds temperature and humidity

specifications. Do not place HomePod near a radiator or heat register or in a built-in

installation unless adequate ventilation is provided.

•

Before cleaning, unplug HomePod from wall outlet. Do not use liquid cleansers or aerosol

cleansers. Use a damp cloth for cleaning.

•

Do not place cords or cables where they may be walked on or tripped over.

Be sure to comply with any applicable local safety standards or regulations.

General-purpose cables are provided with HomePod. The use of any other cables or

requirements mandated by local authority is user’s responsibility.

•

Cables attached to devices in different locations with different power sources and

grounding may cause hazardous voltage. Consult a qualified electronic consultant before

installing the product to check if this phenomenon exists and, if necessary, take

corrective action.

•

Never touch un-insulated telephone wires or terminals unless the line has been

disconnected.

•

Avoid using telephone equipment or installing the product during an electrical storm.

Never install HomePod, or any kind of telephone jacks, lines, network cables, or power

connections in wet locations.

•

Never spill liquid of any kind on HomePod.

Download from Www.Somanuals.com. All Manuals Search And Download.

TABLE OF CONTENTS

1.0 Welcome...................................................................................... 1

2.0 Before You Start.......................................................................... 3

2.1 Package Contents..................................................................... 3

2.2 System and Other Requirements.............................................. 3

3.0 Getting to Know Your HomePod ............................................... 5

3.1 Setting up Your HomePod......................................................... 5

3.2 Front Panel ............................................................................... 6

3.3 Side Connectors ....................................................................... 6

4.0 Server Software Installation....................................................... 9

4.1 Windows Installation ................................................................. 9

4.2 Macintosh Installation.............................................................. 10

5.0 Audio Server Control and Configuration................................ 13

5.1 Server Control......................................................................... 14

5.2 Configuring Audio Folders....................................................... 14

5.3 Configuring iTunes Audio Library ............................................ 15

6.0 HomePod Setup........................................................................ 17

6.1 Wired Setup ............................................................................ 17

6.2 Wireless Setup........................................................................ 17

7.0 HomePod Basic Operation ...................................................... 19

7.1 Turning HomePod On and Off................................................. 19

7.2 Resetting HomePod................................................................ 19

7.3 HomePod Display Menus........................................................ 19

7.4 HomePod Controls.................................................................. 21

7.4.1 Content Navigational Buttons ....................................... 21

7.4.2 Functional Buttons ........................................................ 22

7.4.3 Shuffle/Loop Mode Buttons........................................... 22

7.4.4 FM Radio Buttons: ........................................................ 22

8.0 Web Configuration.................................................................... 23

8.1 IP Settings Page ..................................................................... 24

8.2 Wireless Settings Page........................................................... 25

8.3 Miscellaneous Page................................................................ 26

8.3.1 LCD Sleep Function...................................................... 26

8.3.2 System Shutoff Function............................................... 27

8.4 Radio Stations Page................................................................ 28

8.5 Firmware Upgrade Page......................................................... 29

9.0 Extras Programs and Utilities.................................................. 31

9.1 HomePod Audio Server in Java .............................................. 31

9.2 HomePod Audio Server in Shell Command ............................ 32

9.3 Remote Control Utility in Java................................................. 32

Appendix......................................................................................... 35

Taking Care of Your HomePod...................................................... 35

Troubleshooting ............................................................................ 35

Contacting Macsense.................................................................... 40

Technical Specifications................................................................ 40

Limited Consumer Warranty ......................................................... 42

Getting Service ............................................................................. 43

Download from Www.Somanuals.com. All Manuals Search And Download.

1.0 Welcome

Thank you for purchasing a Macsense HomePod. Your HomePod gives

you access to digital audio files stored on your computer from anywhere

in the house or office.

Download from Www.Somanuals.com. All Manuals Search And Download.

2.0 Before You Start

2.1 Package Contents

Prior to setting up your HomePod, make sure your HomePod package

includes the following items:

• HomePod Unit

• Power Adapter

• Remote Control

• Ethernet Cable

• Stereo Audio Cable

• HomePod CD

• Quick Start Guide

• User Manual

2.2 System and Other Requirements

• Wi-Fi (802.11b or g) Access Point or Wireless Router

• Macintosh G3 or Pentium III PC

• Mac OS 9 and X or Windows 98/Me/2000/XP

Download from Www.Somanuals.com. All Manuals Search And Download.

3.0 Getting to Know Your HomePod

3.1 Setting up Your HomePod

HomePod streams digital audio files stored on your computer, over the

local network (either by wired Ethernet or over a wireless Wi-Fi

network).

Most of the time, HomePod will be used in a wireless environment. A

typical wireless network setup involves a computer connected to a

wireless router (or an access point) to form a wireless network.

HomePod would then connect wirelessly to this same network.

Note: The terms “wireless router”, “access point”, and “base station” are

sometimes used interchangeably in this manual. Wireless router is a device

that combines the functions of an access point plus a switching hub. Base

station is a common term used in the Mac community to refer to an access

point.

Headphone

Access Point

Home Stereo

HomePod

Built-in Speakers

Computer

(Mac/PC)

Music Files

Digital Surround

System

USB Drive

Store Here

Your HomePod can be placed anywhere in the house or office where

the wireless network has coverage. The audio files stored on your

computer can then be played through HomePod’s built-in stereo

speakers, attached headphones, home stereo system, or a high-end

digital surround sound system.

Note: An audio file, such as an MP3 file, is a file that may include music,

speech, narrative, or audio book content. The term “audio server” is used

to describe a computer on your network that contains audio files that will

be served to the HomePod.

The audio collection stored on your computer is recognized by the

HomePod as an “Audio Server”. Each computer with audio content

requires that the HomePod Audio Server Software be installed and

running to make the audio collection available to the HomePod.

One HomePod can access audio content from multiple computers

around the home or office. Conversely, multiple HomePods can

simultaneously access content from the same computer.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.2 Front Panel

Power Button

Infra-red Receiver

irDA Receiver

Display Screen

Jog-shuttle Dial and Enter Button

Navigational and Action Buttons

Built-in Stereo Speakers

Volume Control Buttons

3.3 Side Connectors

HomePod is equipped with a rich set of input and output ports for

interfacing with other audio systems and devices.

FM Radio Antenna

Headphones Jack

RCA Jack, Right

Wi-Fi Antenna

Reset Button

USB Port

RCA Jack, Left

Coaxial Output

SPDIF Output

Ethernet Port

Power

Wi-Fi Antenna

For connecting to the Wi-Fi 802.11b wireless network.

Raise the antenna for better reception.

Reset Button

For resetting the HomePod unit during an unexpected

crash. To reset, use a paper clip pin to poke into the

hole once. Same affect as unplugging and re-plugging

the power cord.

USB Port

For connecting to Flash Memory Stick or USB Hard

Drive. (Optional function.)

Ethernet Port

This 10/100Mbps Fast Ethernet Port is for establishing

a wired connection with your network. If you don’t have

a wireless network in place, you can also connect

HomePod to a wired network.

Power

For plugging in the power cord.

FM Radio Antenna

The FM Radio Antenna is a wire extending from within

the unit. Elongate the wire to get the best radio

reception.

Headphones Jack

Audio RCA Jacks

For connecting to a standard portable stereo

headphone.

For connecting to a home stereo system. Left and

Download from Www.Somanuals.com. All Manuals Search And Download.

Right jacks need to used at the same time.

Coaxial Output

SPDIF Output

For connecting to high-end digital surround sound

system. Only one of the other is used.

Download from Www.Somanuals.com. All Manuals Search And Download.

4.0 Server Software Installation

A small server program, called HomePod Audio Server, must be

installed on each computer that contains audio files that you want to

play through the HomePod. Use the HomePod CD and follow

instructions below to complete the software installation.

4.1 Windows Installation

On the PC, insert the HomePod CD and run the HomePod Audio

Server->Setup.exe.

HomePod Audio Server is based on Java. For Windows PC’s

(98/Me/2000/XP), the installer will alert you to install or upgrade Java

(JRE) if you haven’t already.

Click Yes to install Java Runtime Environment (JRE) into your PC. The

process may take a few moments. Let it run to completion without

interrupting the process. If your PC already has Java installed and you

don’t want to upgrade to the latest version, then click No.

When the installation is complete, you will see a new C:\Program

Files\HomePod\Audio Server\ directory as shown below and a new

entry in Start Menu->Programs->HomePod->Audio Server->HomePod

Audio Server.

Download from Www.Somanuals.com. All Manuals Search And Download.

4.2 Macintosh Installation

On the Mac, insert the HomePod CD and run the HomePod Audio

Server.pkg installer.

You will need to have the administrator password in order to proceed

with the installation. Follow the instructions on screen to complete the

installation.

Download from Www.Somanuals.com. All Manuals Search And Download.

When the installation is complete, you should see a new “HomePod”

folder in the Applications folder.

Download from Www.Somanuals.com. All Manuals Search And Download.

5.0 Audio Server Control and Configuration

To launch the Windows HomePod Audio Server configuration program,

double-click on the HomePod Audio Server icon or select

Start->Programs-> HomePod->Audio Server->HomePod Audio Server.

To start the HomePod Audio Server program on the Mac, go to the

Applications menu and double-click on the HomePod Audio Server icon.

Note: The HomePod Audio Server program for PC and Mac are identical in

function and user interface, so screen shots will be used interchangeably

in this manual.

The HomePod Audio Server Configuration application allows you to set

up and control your audio collection. From this application, you can

define the audio content to be shared, name your audio collection, and

start or stop the server. Once your audio server is configured and

started, your library will recognized by the HomePod.

The window is divided into three frames. The icons in the left side frame

can be selected to view different configuration settings in the right side

frame. The bottom frame contains help information for each

configuration option. Closing the application will minimize the window to

the task tray. You can double-click on the tray icon to open the

configuration window again.

Download from Www.Somanuals.com. All Manuals Search And Download.

5.1 Server Control

Click on the HomePod icon in the left side frame to bring up the main

server controls. This window allows you to monitor and configure the

server settings. The “Audio Server Name” field defines a specific name

for your audio collection that will be displayed on the HomePod.

Examples of some good names are, “John’s Audio Collection”,

“Bedroom Collection”, or “Living Room Audio Library”.

Once you have named you audio collection, you need to define the

contents of your collection. There are two ways to define which audio

files you want included in your collection: by Audio Folders or by

iTunes Audio Library. Other methods will be added to HomePod Audio

Server in the future. If you are using iTunes to manage your audio

collection, proceed to the Configuring iTunes Audio Library section.

5.2 Configuring Audio Folders

An Audio Folder is any directory that contains audio files (such as MP3

files). This is the most generic way of configuring the Audio Server to

locate your audio files. By specifying an Audio Folder, all the audio files

in that directory (including any subdirectories) will become part of your

collection. You can specify more than one Audio Folder, and all the

contents will be combined into one collected and recognized by the

HomePod.

When you click on the Audio Folders icon on the left, you will be

presented with two “Add” options on the right:

To add an Audio Folder, click on the “Add Audio Folder…” icon and

locate the folder that contains your audio files. This may be your C:\My

Documents\My Audio\ directory, or any folder with your audio files that

you'd like to include in your collection. The path to the folder you just

added will be listed on the right frame. You can also configure the Audio

Server to recognize your existing playlists. To add your playlists, click

on the “Add Playlist Folder…” and select the top level folder that

contains your playlist files (.M3U).

After the configuration is complete, click the HomePod icon on the left

frame to return to the server control frame. Press the “Start” button to

Download from Www.Somanuals.com. All Manuals Search And Download.

activate the Audio Server.

5.3 Configuring iTunes Audio Library

If you are using Apple’s iTunes software to manage your audio files,

then you should select this method as the preferred way of configuring

your audio collection so that the HomePod shares the iTunes song and

playlist information.

When you click on the iTunes Audio Library icon on the left side frame,

you will see a “Select…” icon on the right:

Click on the “Select…” icon to locate and open the “iTunes Music

Library.xml” file in the iTunes folder. The .xml file contains the complete

index to the iTunes Music Library songs and playlists.

Download from Www.Somanuals.com. All Manuals Search And Download.

To share an iTunes Music Library with the HomePod, the iTunes

program need not be running.

After the configuration is complete, click the HomePod icon on the left

side frame to return to the main server control frame. Press the “Start”

button to activate the Audio Server.

Download from Www.Somanuals.com. All Manuals Search And Download.

6.0 HomePod Setup

There are two ways to connect the HomePod to your network, wired

(with an Ethernet cable) or wirelessly (through Wi-Fi). The two methods

are mutually exclusive at startup time, i.e. when one is enabled the

other will become disabled. When HomePod is first powered up, it will

try to detect if an Ethernet cable is attached. If it is, the Ethernet

connectivity will have priority over wireless connectivity. If an Ethernet

cable is not connected to the HomePod at startup, the HomePod’s

wireless connection will be activated. For most users, HomePod will be

used in a wireless environment so the Ethernet port need not be used.

Follow the instruction below for each connection setup.

6.1 Wired Setup

Before turning on the HomePod, connect it to your network with the

enclosed Ethernet cable. HomePod can be connected to a wireless

router or a switching hub. Next, plug in HomePod and turn it on. The

boot up process will take about 20 seconds, after which HomePod

should discover any Audio Servers that have been activated.

6.2 Wireless Setup

Make sure that you have already set up a wireless router or access

point (base station) to form your wireless 802.11 b/g network. Your

computers and HomePod must be in the same domain as the router

(e.g. all must be in 192.168.1.x). Confirm that the DHCP server on the

access point is running so that your computers and HomePod can

automatically obtain IP addresses automatically (this is usually on by

default). If you have WEP encryption enabled in the access point, turn it

off for now; you can turn it back on later after the HomePod is running

smoothly. Next, plug in the power adapter and turn on the HomePod.

The boot up process will take about 20 seconds, after which HomePod

should discover any Audio Servers that have been activated.

If the HomePod is unable to find any Audio Servers even though they

are running, try the following: Turn off HomePod. Connect the HomePod

to the router by a wired Ethernet cable, and then turn on the HomePod

again. When HomePod reaches the main screen, go to Network

Settings and locate its IP Address. Once the IP is known (say

192.168.1.3), open a browser on any computer on the network and log

into HomePod, e.g. type http://192.168.1.3/ in the browser. Once you

are at the configuration screen, go to the Wireless Settings tab and look

for the SSID field. Change the SSID from the default value of “ANY” to

the exact name of your access point (you can get the SSID of your

access point by logging into your access point). Click Save and then

disconnect the Ethernet cable and reboot HomePod. In a multi-access

point environment, setting the SSID to match your access point will help

HomePod connect to it much more easily.

If you still have trouble finding an Audio Server, refer to the

Troubleshooting section in the Appendix section of this manual. Also

Download from Www.Somanuals.com. All Manuals Search And Download.

review the Wireless Settings Page details in the Web Configuration

section of this manual.

Download from Www.Somanuals.com. All Manuals Search And Download.

7.0 HomePod Basic Operation

7.1 Turning HomePod On and Off

To turn on the HomePod, press and release the

Power button. You

should be prompted with a startup screen that displays “HomePod

Wireless Audio Services”.

To turn off the HomePod, press and hold the

seconds.

Power button for two

7.2 Resetting HomePod

In the rare event that HomePod is hung and does not respond to button

presses, you can reset the unit by poking on the reset button on the left

back side of HomePod using a paper clip, or you can temporarily unplug

the power cord to cycle the power.

7.3 HomePod Display Menus

HomePod menu system is a tree structure. You start at the Main Menu,

and every item on the menu either enters another sub-menu, or it

terminates in a screen in that branch.

The following is a tree structure of the HomePod menu system.

[Audio Server Name]

+ All Songs

+ Artists

+ Albums

+ Artist/Albums

+ Genres

+ Playlists

+ FM Radio

+ Settings

+ Network Settings

+ Network Information

+ IP Address Configuration

+ Dynamic IP Address

+ Set Static IP Address

+ Signal Strength

+ Speakers

+ Contrast

The Main Menu will automatically detect and list any Audio Servers

found on the network, listing one line for each audio library. If no

libraries are detected, then the first line will display “Searching for Audio

Servers”. Click the

button to refresh the list of Audio Servers.

Download from Www.Somanuals.com. All Manuals Search And Download.

Each audio collection can be navigated by categories based on their

ID3 tags. The category menus are designed to facilitate easy location of

songs, artists, or albums form a large audio library. A typical audio

collection can contain hundred or thousands of songs. By using the

category menus, you can find what you want in a few quick steps. The

categories include: song title, artists, albums, artists/albums, genres,

and playlists. These categories are the same as those used by most

popular audio managers, such as iTunes, AudioMatch, MediaPlayer, or

WinAmp.

Press

navigate your audio content based on that category. The first item within

each category is Play All; press again to start playing all the song in

to select any category. The HomePod will allow you to

the current list. You can also scroll to the items below and select a

specific song, album, artists or playlist, depending on the category.

The Play Screen is displayed when a song is being played by

HomePod. This screen gives additional information about the song that

is being played. In the top left corner, it displayed the Genre. The

second line aligned left displays the Name of the song. The third line

aligned right is the Artist of the song. The forth line aligned left is the

Album of the song, and alight right is the Track Number of the song in

the album.

From the main menu, you can also select FM Radio to listen to local

radio stations. The FM Radio screen allows you to tune to your local FM

radio stations when you’re not listening to your network audio collection.

Your can define up to 20-preset radio stations so you can jump to them

easily using the navigational keys (see the Web Configuration section

for details). To turn the frequency up and down, turn the rotating dial

clockwise or counter-clockwise. To jump to the next or previous preset

stations, use the

buttons.

Download from Www.Somanuals.com. All Manuals Search And Download.

Settings Menu lists the settings that you can either check or set from the

HomePod. The Network Settings menu displays important settings that

are crucial to network connection. The Speakers item controls the sound

coming out of HomePod’s build-in speakers. The menu item toggles On

and Off with each press of the

key. The Contrast item controls the

brightness of the LCD. Rotate the center dial to turn the contrast value

up or down.

The Network Settings Menu opens up screens that facilitate monitoring

of network settings on HomePod. In the Network Info sub-menu, you

can check the current IP, subnet mask, gateway IP address of the

HomePod. Use this information to troubleshoot when your HomePod is

having trouble connecting to your network. The Set IP Address menu

item is used wh.6(yo)-5(ur H)4.81lepness of th2ask, gatework Sa f009 Tcx9.8(e md.

- The Way You Were

+ Artists

+ Albums

+ Artists/Albums

+ Genres

+ Playlist

Use the rotating dial to navigate up and down any list.

Press the

button to select an item in the list, or press the

button

to come out of a list.

7.4.2 Functional Buttons

To play a song, press the

highlighted on the list.

button or the

button when the song is

To pause a playing song, press the

resume play.

button. Press

again to

If you are playing a collection of songs (such as an album or random

play mode) press the button to skip to the next.

To jump to the beginning of a song while it is playing, press the

button.

If you’re using the built-in speaker or the headphones port, to increase

the volume, press the

button.

button; to decrease the volume, press the

7.4.3 Shuffle/Loop Mode Buttons

To shuffle a list of songs, while a list of songs is playing in the play

mode, press the

button. Press

again to exit shuffle mode.

To repeat a song or list of songs, press the

button while a song is

playing. If an individual song was selected, the Loop function will repeat

that one song over and over. If the playing song is part of playing list,

then the whole list of songs will repeat once completed.

7.4.4 FM Radio Buttons:

To start FM Radio, at the main menu, scroll to "FM Radio" and press the

button.

To jump to the next preset station, click the

button.

To jump to the previous preset station, click the

To adjust the frequency of the tuner, rotate the dial right and left.

Download from Www.Somanuals.com. All Manuals Search And Download.

8.0 Web Configuration

HomePod includes a built-in web configuration page that you can

access from any browser (Internet Explorer, Apple Safari, AOL

Netscape, etc.) on a computer connected to the network. You can set

many of the advanced functions using this configuration.

To access the web configuration page:

Launch your browser and type in the IP address of the HomePod; e.g. if

your HomePod's IP address is 192.168.1.3, then type

"http://192.168.1.3" in your browser (to obtain HomePod’s IP address,

navigate to Settings:Network Settings:Network Info).

When prompted for a username and password, leave username blank

and type "admin" as the password. "admin" is the default password and

can be changed after the first time you log into the device. Make sure to

note your new password if you change it.

Download from Www.Somanuals.com. All Manuals Search And Download.

8.1 IP Settings Page

This page sets the basic TCP/IP settings for your HomePod.

HomePod Hostname is useful in identifying your HomePod on the

network, especially when you have more than one HomePods on the

network. The hostname you defined here will also appear in the DHCP

IP table of your router or access point.

If your router or network server has a DHCP server that assigns IP

addresses, then you should select Dynamic IP so an IP will be

assigned to HomePod automatically whenever the HomePod is

connected to the network. This is the default and preferred way for

HomePod to join a network because everything is plug-and-play.

If you network doesn’t automatically assign you an IP address then you

need to define basic TCP/IP settings manually. Select Static IP and

enter the IP Address, Subnet Mask, Default Gateway/Router, Preferred

DNS, Alternate DNS (optional) into their respective fields. These TCP/IP

values register your HomePod on the network.

After you make the changes, click on the Save button to save the

settings. You must restart your HomePod for the new settings to take

effect.

Download from Www.Somanuals.com. All Manuals Search And Download.

8.2 Wireless Settings Page

This page enables you to configure basic wireless settings to

allow your HomePod to connect to an 802.11b/g Wi-Fi wireless

network.

Network Name (or sometimes referred to as the SSID) is the name of

the wireless network that HomePod should connect to. The network

name is defined by the access point. Any wireless computers or devices

(such as HomePod) that connect to the same network name will form

one network. You can find out what the network name is by accessing

the web config page of your access point.

Note: For Apple Base Station users and other advance access points, make

sure the SSID of your access point is not “hidden” or set to "closed

network".

By default, the Network Name field is set to “ANY” and HomePod will

automatically detect and connect to the strongest access point in the

surrounding area. For most users this is the preferred and most

convenient setting. But if you have multiple access points with different

network names around you, or if the HomePod somehow is not

connecting to the access point of your choice, then you will want to

specify a network name manually.

A Network Mode is the topology in which a wireless network is set up.

An Infrastructure network mode, which is the default setting, uses one

or more access points to form a wireless network. This is in contrast to

Ad-hoc (also referred to as Peer-to-Peer) network mode, in which two

wireless devices communicate with one another without the existence of

an access point. Ad-hoc is useful if you want to connect a HomePod to

your computer and listen to its shared library directly without an access

point.

Download from Www.Somanuals.com. All Manuals Search And Download.

To set the network mode, click on the appropriate button.

In the ad-hoc mode, the Channel defines the frequency at which

HomePod will communicate with the other ad-hoc device, in this case

another computer. Both the HomePod and the other computer must

operate in the same network name and channel. The channel field is not

used if the network mode is set at infrastructure.

To set the channel, pull down the list and select a channel from 1

through 14.

If the access point has WEP Encryption turned on, then HomePods

needs to be set with the same encryption parameters, and also have the

matching key.

To turn on WEP encryption on the HomePod, select the Enable button

and click either the 64-bit or 128-bit option. Enter the WEP key in hex in

its respective field, Key 1 through 4; normally only Key 1 is used. If the

WEP Encryption is 64 bit, the hex key requires 10 characters. If the

WEP Encryption is 128 bit, the Hex key requires 26 characters. A hex

key is a continuous stream of hex characters (0-9, A-F) without hyphen

or space between them.

Note: For WEP encryption, set the base station or access point to use the

“Share Key” mode.

After saving the changes, you must restao(h 14.pl Tc0.802 Tw -9.7(o)1.6(r)-he net)11.7(w)1

continue to play while the LCD goes into sleep mode. Pushing any

buttons on the HomePod will turn the LCD back on. This function is

designed to protect and extend the life the LCD when it is not needed

for viewing. The default setting is "Never".

To turn on the LCD Sleep function:

1. Access the web-config page of HomePod.

2. Click on the Miscellaneous tab, and set the LCD Sleep time to

either 1, 5, or 15 minutes.

3. Click on the "Submit" button to save the settings.

4. Reboot HomePod.

8.3.2 System Shutoff Function

HomePod also offers a System Shutoff function that will turn the whole

unit off at a designated time to protect the unit from unnecessary

prolonged usage. This function is designed for people who use

HomePod to sooth them to sleep. The default setting is "Never".

To turn on the System Shutoff function,

1. Access the web-config page of HomePod.

2. Click on the Miscellaneous tab, and set the unit System Shutoff

time to 15, 30, or 60 minutes Click on the "Submit" button to save

the settings.

3. Reboot HomePod.

Download from Www.Somanuals.com. All Manuals Search And Download.

8.4 Radio Stations Page

This page allows you to preset twenty FM radio stations. The stations

you define here will appear in the FM Radio list on the HomePod.

You can define up to 20 FM radio stations. The stations you defined

here will allow you to jump to these stations quickly with the press of the

and

buttons on the HomePod.

Twenty local FM radio stations in San Francisco have been set up in the

Radio Stations page as default. You can change the stations for your

location.

If you are not getting good reception, unwind and extend the antenna

wire on the back of HomePod.

To preset FM radio stations:

1. Access the web-config page of HomePod.

2. Click on the Radio Stations tab.

3. Enter the name of the station in the Name field (maximum 20

characters); you can enter the call letter of a radio station (e.g.

"KFRC") or a short description for the type of audio that this station

plays (e.g. "80's Easy Listening").

4. Enter the frequency in the Frequency field (e.g. "101.3").

5. Click on the "Submit" button to save the settings.

Reboot is not necessary. The settings will be available the next time you

use the FM Radio.

Download from Www.Somanuals.com. All Manuals Search And Download.

8.5 Firmware Upgrade Page

This page displays the current version of your Firmware and Boot ROM,

and enables you to upgrade your HomePod firmware to new versions

as they become available.

For tech support service, it is often needed to know which versions of

Firmware and Boot ROM you have installed in the HomePod. The

versions info is displayed in the format of a version number followed by

a date time, as below:

Current Versions:

Firmware version:v.1.0.5, 01/28/04

BootROM version: v.2.7, #317 Tue Jan 27 12:00:32 CST 2004

From time to time, Macsense offers upgrades to HomePod firmware to

add new features and fix bugs. The HomePod firmware will be

distributed as a compressed encrypted file named "homepod.tar.zip".

New updates will be posted on Macsense website when available

(http://www.macsense.com/homepod).

To upgrade HomePod firmware:

1. Download "homepod.tar.zip" to the desktop of your computer.

2. Log into the HomePod’s web-config page.

3. Click on the Firmware Upgrade tab.

4. Click the "Browse..." button.

5. Locate the "homepod.tar.zip" file on your desktop.

6. Press the "Upgrade" button and wait 3 minutes. If upgrade is

successful, you will be prompted with a successful message.

7. Reboot HomePod.

Download from Www.Somanuals.com. All Manuals Search And Download.

9.0 Extras Programs and Utilities

HomePods provides extra programs and utilities that you can use on

your Mac, PC, or Linux computers that provide additional functions.

9.1 HomePod Audio Server in Java

Another pure-Java version of the HomePod Audio Server is included on

the HomePod CD. If you are using Mac OS 9 or a Linux computer

where the native version of the HomePod Audio Server is not available,

you can use the Java-version of the server. The Java version of the

HomePod Audio Server is universally compatible, and can also work

under Mac OS X and Windows 98/Me/2000/XP as well. The Java

version is functionally identical to the native servers with the exception

of user interface differences.

The Java version of the HomePod Audio Servers is located in the Extras

folder on the HomePod CD. Copy the "HomePod Audio Java Server”

folder to the desktop. You can move the "HomePod Audio Server" folder

to anywhere in your hard drive, as long as you move it as a whole.

Note: HomePod Audio Java Server is Java-based and requires that Java

already be installed before you initiate the Audio Server installation. For

Windows, go to Sun's Official Java site to download and install the latest

Java runtime Environment (JRE) release,

http://www.java.com/en/download/. For Macintosh, Java VM is built-in into

the Mac OS X and therefore need not be installed separately. For Mac OS 9

users, use the installer “MRJ 2.2.5 Install.smi”also available on the

HomePod CD.

If you are using Apple iTunes to manage your music files, use

"ituneslibrary.jar" as the server program. A window with three fields

would appear. In the first field, name your audio collection, e.g.

"HomePod Music Library" or "Bedroom Collection". In the second field,

use the "Browse..." button to locate the "iTunes Music Library.xml" file in

the iTunes folder, and press the "Open" button. (Note, you’re selecting

the location of the .xml file and not the iTunes Music folder itself.) When

all configurations are done, press the "Start" button to activate the Audio

Server. The songs will first be indexed as indicated by the progress bar.

To stop the audio server, click the "Stop" button.

If you are not using Apple iTunes, run the "filesystemlibrary.jar" as the

server. A window with three fields would appear. In the first field, name

your audio collection, e.g. "Ryan's Music Library" or "Bedroom

Collection". In the second field, use the "Browse..." button to locate the

directory where you store all your audio files. This may be your C:\My

Download from Www.Somanuals.com. All Manuals Search And Download.

Documents\My Music\ directory, or any folder or sub-folder with your

audio files that you'd like to make available to the HomePod. When all

configurations are done, press the "Start" button to activate the Audio

Server. To stop the audio server, click the Stop button.

9.2 HomePod Audio Server in Shell Command

HomePod Audio Server is also available as a GUI-less command line

that you can run from a command terminal. The advantage of having

such a version is the ability to host a HomePod Audio Server in

professional and residential Linux media servers with no attached

monitor, and remotely managed by Macs and PCs. To get this version of

the HomePod Audio Server, please write to Tech Support.

9.3 Remote Control Utility in Java

A Java remote control utility is provided that allows you to control one or

multiple HomePods from your Mac/PC. You can control everything that

you can do on the HomePod unit itself. The Java remote control utility is

handy when you’re far away from the HomePod and you’d like to

centrally control the HomePod all at once. The Java remote control

utility is named “pdaremote.jar” and is located in the HomePod

CD->Extras->HomePod Audio Java Server directory.

Double click the pdaremote.jar icon to launch the remote control. Once

opened, you’ll be presented with a window below.

Download from Www.Somanuals.com. All Manuals Search And Download.

The “Players” field in the bottom half of the window lists all the

HomePods located on the network. Select one from the list that you

wish to control. The “Libraries” field on top of the window is a pull-down

menu listing the available Audio Server on the network. Use the buttons

to navigate the list or play and stop songs as you would control the

HomePod using the physical HomePod unit.

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix

Taking Care of Your HomePod

(Failure to follow these instructions may result in personal injury or

damage to your HomePod.)

• Use only a soft, dry cloth to clean the outside of your HomePod and

any peripherals.

• Do not use any solvents, chemicals, or cleaning solutions containing

alcohol, ammonia, or abrasives.

• Do not allow liquids to spill on the unit.

• Do not use sprays near your HomePod.

• It is best to keep HomePod out of direct sunlight or other sources of

extreme heat.

• Avoid placing HomePod in a setting where air cannot circulate

around the unit.

Troubleshooting

Your HomePod is designed and built to provide you with trouble-free

performance. If it does not appear to be functioning correctly, please

follow these troubleshooting steps.

General troubleshooting guidelines:

• Make sure all connectors are properly attached.

• Make sure the power adaptor is firmly connected.

• Try the basic setup first before attempting complex ones. Involve only

one access point, one audio server, and one HomePod. Try wired

(Ethernet cable) connection before trying wireless (access point).

Turn wireless encryption (WEP) off.

If this is

Try the following:

happening:

HomePod is

Do not connect the Ethernet cable when using

connected wirelessly the wireless connection. If the Ethernet cable

to the network and it

does not see any

audio servers.

is connected at boot-up time, wireless

connection will not be enabled.

Check to make sure that the HomePod is

getting a proper IP Address and SSID by

selecting the “Settings->Network Settings”

item on the main menu. The IP and SSID will

only appear if the HomePod has successfully

connected to a wireless network. Without

them, the audio server will not be recognized.

Download from Www.Somanuals.com. All Manuals Search And Download.

HomePod is

Check the access point to make that it is

connected wirelessly working properly. Check to see if you have

to the network and it

does not see any

audio servers.

basic TCP/IP settings setup correctly, such as

IP, subnet mask, gateway IP, SSID, WEP

keys.

(Continued…)

Move your HomePod closer to your access

point to see if range could be an issue.

Check to see if your access point is set to

broadcast the SSID. Enable it if it is not. The

HomePod needs the access point to

broadcast the SSID in order to connect to it.

If your access point has WEP turned on,

turned it off first to make sure HomePod can

connect without WEP.

Turn off HomePod. Connect the HomePod to

the router by a wired Ethernet cable, and then

turn on the HomePod again. When HomePod

reaches the main screen, go to Network

Settings and locate its IP Address. Once the IP

is known (say 192.168.1.3), open a browser

on any computer on the network and log into

HomePod, e.g. type http://192.168.1.3/ in the

browser. Once you are at the configuration

screen, go to the Wireless Settings tab and

look for the SSID field. Change the SSID from

the default value of “ANY” to the exact name

of your access point (you can get the SSID of

your access point by logging into your access

point). Click Save and then disconnect the

Ethernet cable and reboot HomePod. In a

multi-access point environment, setting the

SSID to match your access point will help

HomePod connect to it much more easily.

Make sure the PC/Mac that has audio server

installed is on the same subnet as the

HomePod. E.g. 192.168.1.xxx.

Make sure the audio server is running. If it is

not, start it. If it is, stop and restart it.

Download from Www.Somanuals.com. All Manuals Search And Download.

HomePod is

Connect the Ethernet cable before turning on

the HomePod. If the Ethernet cable is not

connected at boot-up time, wireless

connected via

Ethernet to the

network and it does

not see any of audio

servers.

connection will be enabled instead.

Check to make sure that you have a green

light on the HomePod’s Ethernet port.

Check to make sure that the HomePod is

getting a proper IP Address by selecting the

“Settings->Network Settings” item on the main

menu. The IP will only appear if the HomePod

has successfully connected to a wireless

network. Without it, the audio server will not be

recognized.

Make sure that your network has a DHCP

server available.

Make sure the PC/Mac that has audio server

installed is on the same subnet as the

HomePod. E.g. 192.168.1.xxx.

Make sure the audio server is running. If it is

not, start it. If it is, stop and restart it.

HomePod is getting

an IP address but it

still can not find any

audio servers.

Make sure the audio server is running. If it is

not, start it. If it is, stop and restart it.

Make sure that all software firewalls are

disabled. This includes firewalls that are part

of the operating system.

: Open Start->Settings->

Control Panel->Network Connections. The

Network Connections window will open.

Right-click on the network adapter that is in

use and select Properties. Click the Advanced

tab. Uncheck the Internet Connection Firewall

checkbox and save settings.

: Open System

Preferences and click Sharing. Click Firewall

and click the Stop button.

Wireless is not

The Ethernet cable needs to be inserted at the

working so I inserted time the HomePod is turned on. If there is no

an Ethernet cable

but it still doesn’t

work.

cable inserted at the start-up time then the

Ethernet port becomes disabled and wireless

becomes active. So even if a cable is inserted

after start-up the Ethernet port is already

disabled and will not function.

Download from Www.Somanuals.com. All Manuals Search And Download.

WEP does not work.

64-bit and 128-bit WEP Encryptions are

supported. Make sure that your access point is

set to accept "Shared Key" and the hex key is

typed in the HomePod web config page in the

Key #1 field.

Only hex keys are accepted. Turn ASCII key to

hex before using.

Make sure the hex key is entered correctly as

a continuous stream without spaces or

hyphens.

Buttons are slow to

respond under

wireless mode.

A degradation of the signal strength or sudden

signal interference on the wireless network

can cause this type of behavior. Wait a little

longer for the buttons to respond. Do not keep

on pushing the buttons repeatedly.

Look for the interference sources, such as

your cordless phone, microwave oven, TV

antenna, and monitors. Remove the sources

or place the access point and HomePod away

from these sources.

There is no sound or Check the volume control on the HomePod

sound volume is low

when played.

and make sure that the volume is turned up.

Maker sure mute button on the remote control

unit is not activated. Press the mute button

again to deactivate mute.

Audio sound is

distorted.

Confirm if the same song sounds any better

when played on the computer. Perhaps the

song was just encoded badly from the source.

Audio sound is

distorted when

output to external

speakers.

Check the volume control on the HomePod

and make sure that the volume is not turned

all the way up. When outputting to external

speakers, set the volume on the HomePod to

about one third only and let the amplifier of the

external speakers/receivers do the

amplification.

Pressing the

The

button works in the same way a CD

button does not jump player does. While a song is playing, push it

to the previous song

but repeats the

same song.

once and it will go back to the beginning of the

playing song. Pushing it twice will go to the

previous song.

AAC songs do not

play.

AAC support is still currently under

development. We will offer free upgrades to

current HomePod owners when it is available.

Download from Www.Somanuals.com. All Manuals Search And Download.

Songs purchased

from Apple Audio

Store do not play.

Songs purchased from Apple Audio Store are

protected in a special AAC-DRM format and

are not playable on HomePod. Apple does not

allow third party products aside from iPod and

iTunes to decode and play these songs.

Unless Apple changes this policy, AAC-DRM

playback on non-Apple players such as

HomePod will not be legally possible.

Remote control does Make sure the plastic protective slip insulating

not work.

the battery compartment is pulled out.

Make sure that you are pointing the remote at

the small circular hole located on the top left

corner of the front of the HomePod. Make sure

no physical obstruction is there between the

Remote and HomePod.

Make sure the emitter on the remote control

unit is pointing towards the HomePod.

HomePod hangs

while booting up.

Shut off the HomePod by holding down the

power button for two seconds, insert a paper

clip in the reset hole on the side of the

HomePod, or unplug and re-plug the power

cord. Hold a few seconds and restart the unit

again.

Power off button

does not turn the

unit off.

The Power button has a prolonged timing

mechanism to prevent accidental shut off.

Press and hold the Power button down for two

seconds to turn the unit off.

If the unit indeed hung and does not respond

to the Power button, unplug and re-plug the

power cord and try again.

Audio is playing, but

the LCD is dark.

The LCD Sleep function in the web config

page is turned on.

The contrast is set too low. Go to Settings->

Contrast on HomePod’s main screen to

increase the contrast value.

The FM reception is

bad.

Make sure the antenna wire is extended

outward. Be careful not to pull out the antenna

from inside the unit.

HomePod unit

topples or slides

easily.

Check to see if the four pads are in place on

the base of the unit. If these pads are present,

email us to get free replacement

Download from Www.Somanuals.com. All Manuals Search And Download.

Contacting Macsense

For additional information in solving problems with your HomePod,

contact Macsense Tech Support.

Technical Support Hours: 9am – 4:30pm PST

Phone: 1-800-642-8860 x100 (Free Support)

Email: [email protected]

Web:

upgrades and promotions.

We upgrade firmware periodically to include support on new functions

and bug fixes. Remember to check website for the latest updates.

Technical Specifications

• Toshiba TX4926 200MHz CPU

• 16MB Flash RAM, 32MB SDRAM

• 124x64 pixel graphical back-lit blue LCD display

• Jog-shuttle rotating dial

• 802.11b 11Mbps mini-PCI Card with external antenna

• RJ-45 10/100Base-T Ethernet Port

• Left, right and headphone audio outputs

• Built-in stereo speakers

• Digital coaxial and optical SPDIF ports

• FM tuner with wire antenna

• USB 1.1 port, host-powered

• Web-configurable and upgradeable firmware

• IR and IrDA ports

• 18-key remote control

Physical Dimensions and Weight

• Body thickness 3/4" (1.9cm)

• 7" W x 5" H x 2" D (17.8 x 12.7 x 5cm)

• 15.3 oz (434g)

OS Support

• Mac OS 9 and OS X

• Windows 98/Me/2000/XP

Supported Media Manager

• Apple iTunes, Microsoft MediaPlayer, Audio Match Jukebox, Nullsoft

WinAmp

Supported Audio Formats

• MP3 and Internet Radio currently and upgradeable to AAC, WMA,

WAV and more.

Download from Www.Somanuals.com. All Manuals Search And Download.

Software

• Firmware and desktop software. Powered by GLOO^TMopen media

platform. GLOO is an open, Java-based media platform that handles

the discovery, request, transfer, and control of audio content on

HomePod.

• FM radio tuner with 20 preset stations. Station name and frequency

can be defined by user through web interface.

• Unicode. Support for English, Spanish, French, Italian, German,

Hebrew, Arabic, Chinese, Japanese, Korean, and other languages.

Download from Www.Somanuals.com. All Manuals Search And Download.

Limited Consumer Warranty

Macsense Connectivity (“Macsense”) warrants all HomePod products sold

(“Products”) to be free of defects in material and workmanship, subject to the

following conditions.

The duration of Macsense’s warranty with respect to Macsense HomePod

product is limited to one (1) year from the date of sale to the original consumer

purchaser.

No other express warranties are made with respect to any Product. All implied

warranties, including warranties of merchantability and fitness for a particular

purpose are limited to the warranty period set forth above. The warranty is not

transferable and applies only to the original consumer purchaser of the Product.

Macsense will, as its sole obligation under this warranty, replace or repair, at its

option any Product that does not conform to this warranty. Under no

circumstances will Macsense be liable for any incidental or consequential

damages under this warranty or any implied warranties.

Macsense will not be responsible for damage resulting from any (i) deviation from

Macsense’s operating instructions as printing in Macsense’s catalog or on any

packaging, labels or other literature provided with a Product, (ii) installation of a

product in a manner which is inconsistent with Macsense’s written instructions,

(iii) alteration or modification of a Product, (iv) misuse, (v) neglect, (vi) abuse, (vii)

accident, (viii) normal wear and tear, (ix) commercial use, (x) service by anyone

other than a Macsense authorized repair facility, or (xi) other improper

application, installation or operation of the Product.

Download from Www.Somanuals.com. All Manuals Search And Download.

Getting Service

To obtain warranty service during the first thirty (30) days after the date

of purchase, you must return the defective Product with the original

receipt to the original place of purchase. To obtain warranty service

during the remainder of the warranty period, you must contact

Macsense by phone at (650)552-9110 or by fax at (650)552-9250.

When contacting Macsense by fax, please include a letter detailing your

complaint and provide a daytime phone number where you can be

reached. If further clarification or additional information is required from

Macsense, you may call us.

If warranty service is needed at any time during the warranty period, the

purchaser will be required to furnish a sales receipt/proof of purchase

indicating the date of purchase; amount paid and place of purchase.

Customers who fail to provide such proof of purchase will be charged

for the repair of any Product.

How state law relates to the warranty:

Some states do not allow limitations on how long implied warranties last,

or the exclusion or the limitation of incidental or consequential damages.

So the above limitations or exclusions may not apply to you. This

warranty gives you specific legal rights. You may also have other rights

that may vary from state to state.

NO PERSON IS AUTHORIZED BY MACSENSE TO MODIFY OR ADD

TO THIS LIMITED WARRANTY.

Macsense Connectivity

857 Hinckley Road

Burlingame, CA 94010

U.S.A.

www.macsense.com

The Macsense logo and HomePod name are trademarks of Macsense Connectivity.

GLOO is a trademark of Gloolabs, LLC.

HC-020304

Download from Www.Somanuals.com. All Manuals Search And Download.

La Crosse Technology Clock Radio WT 5720 User Manual
Land Pride Lawn Aerator CA25 User Manual
Lenoxx Electronics CD Player CD 1492 User Manual
Life Fitness Stepper Machine LS8500 User Manual
Manitowoc Ice Ice Maker AC 0370 User Manual
Marshall Amplification Stereo Amplifier MG100DFX User Manual
Melissa Fan 271 001 User Manual
Metra Electronics Cell Phone 99 7609G User Manual
MGE UPS Systems Power Supply 3200RT User Manual
Microsoft Computer Accessories 79G 03775 User Manual