CU300 and CR300
Exercise Bikes
U S E R M A N U A L
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using this product, it is essential to read this
ENTIRE operation manual and ALL installation instructions.
This will help in setting up the equipment quickly
and in instructing others on how to use it correctly and safely.
FCC Warning - Possible Radio / Television Interference
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a resi-
dential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used
in accordance with the operation manual, may cause harmful interference to radio communications. However, there is no
guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Class HB (Home): Domestic use. Not suitable for therapeutic purposes.
CAUTION: Any changes or modifications to this equipment could void the product warranty.
Any service, other than cleaning or user maintenance, must be performed by an authorized service representative. There
are no user-serviceable parts.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Unpacking and Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
1.
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
1.1
1.2
Set-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Where to place the Bally Exercise Bike // How to stabilize the Bally Exercise Bike // How to Adjust
the Seat // How to Adjust the Pedal Straps // Starting Up the Bike
2.
The Display Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
2.1
2.2
2.3
3.
The Display Console Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Display Console Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
The Accessory Tray (optional) and Reading Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Heart Rate Zone Training Exercise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Why Heart Rate Zone Training Exercise? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Heart Rate Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
The Telemetry Heart Rate Chest Strap (optional)
3.1
3.2
4.
The Workouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Workout Overviews . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Using the Workouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
4.1
4.2
To Begin any Workout // Selecting Quick Start // Selecting a Workout // Entering a Duration //
Entering Age // Selecting the Difficulty Level or Target Heart Rate // Pausing Workouts //
Ending Workouts Early // Bally Exercise Bike Workout Setup Steps (chart)
4.3
Workout Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Quick Start // Hill // Random // Manual // Outdoor Training // Gradual Hill //
Fat Burner (optional) // Cardio (optional)
5.
Optional Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Entering and Using the Optional Settings Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Service and Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Preventative Maintenance Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Preventative Maintenance Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Troubleshooting the Telemetry Heart Rate Chest Strap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Heart Rate Reading is Erratic or Absent Entirely // Heart Rate Reading is Erratic or Extremely High
How to Obtain Product Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Upright Exercise Bike Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Recumbent Exercise Bike Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
5.1
6.
6.1
6.2
6.3
6.4
7.
7.1
7.2
© 2002 Life Fitness, a division of Brunswick Corporation. All rights reserved. Life Fitness and Heart Rate Zone Training are registered
trademarks of Brunswick Corporation. Bally is a registered trademark of Bally Total Fitness. Any use of these trademarks, without the
express written consent of Life Fitness or the corresponding companies is forbidden.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
UNPACKING THE UPRIGHT EXERCISE BIKE
1. Carefully cut and remove the SHIPPING BANDS.
2. Carefully cut the tape securing the TOP FLAPS.
3. Fold the TOP FLAPS outward fully.
4. With the help of another person, remove the TOP
SHIPPING TRAY.
CAUTION: Some parts extend through the bottom
of the SHIPPING TRAY. Be careful not to damage
the parts when lifting the TOP SHIPPING TRAY
from the SHIPPING CARTON.
5. Remove the DISPLAY CONSOLE carton and the
HANDLEBAR ASSEMBLY from beside the BASE
UNIT.
6. With the help of another person, lift the BASE UNIT
from the SHIPPING CARTON. Remove the protective
packaging from the unit.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Slide the SEAT POST CAP (R) downward to meet the top of
the SEAT POST SUPPORT (T). Secure the SEAT POST
CAP to the SEAT POST SUPPORT using two 1/4" PHILLIPS
SCREWS (6). Tighten the SCREWS securely. Do not over-
tighten the SCREWS.
ASSEMBLING THE UPRIGHT EXERCISE BIKE
Tools Required: Metric Wrench Set, Metric Allen
Wrench Set, Phillips Screwdriver
1. Locate and install the two LEVELER FEET (A) to the bottom
13. Begin inserting the SEAT ADJUSTMENT KNOB (U). Lift
upward on the SEAT (O) and SEAT POST (P) until the SEAT
POST locks into a position. Tighten the SEAT ADJUSTMENT
KNOB fully. Insert the 1/4" PHILLIPS LOCKING SCREW (11)
and tighten securely.
of the REAR STABILIZER (B).
2. Attach the REAR STABILIZER (B) to the BASE UNIT (C)
using two 2-3/8" BUTTON HEAD SCREWS (1) from the top
of the REAR STABILIZER BRACKET (D) and two 13/16"
BUTTON HEAD SCREWS (2) from the front side of the
REAR STABILIZER BRACKET. Tighten the SCREWS
securely.
NOTE: It is important to tighten the SEAT ADJUSTMENT
KNOB (U) fully before inserting the LOCKING SCREW (11).
14. Remove the DISPLAY CONSOLE (V) from its shipping car-
ton. While holding the CONNECTOR (W), cut the wire tie
securing the CONNECTOR to the DISPLAY CONSOLE
BRACKET (X). Position the DISPLAY CONSOLE above the
DISPLAY CONSOLE BRACKET. Connect the CONNEC-
TOR leading from the DISPLAY CONSOLE BRACKET to the
corresponding jack located on the back of the DISPLAY
CONSOLE. Secure the DISPLAY CONSOLE to the DIS-
PLAY CONSOLE BRACKET using four 1/2" PHILLIPS
SCREWS (6). Tighten the SCREWS securely. Do not over-
tighten the SCREWS.
3. Locate the MONOCOLUMN (E). Cut the WIRE TIE securing
the WIRE (F) to the bottom of the MONOCOLUMN. Slide the
MONOCOLUMN COVER (G) onto the MONOCOLUMN (E)
as shown. Slide the MONOCOLUMN COVER up to the
HANDLEBAR TUBE (H).
5. Locate and insert the GROMMET (J) into the SIDE ACCESS
HOLE (K) of the MONOCOLUMN (E). Pull the WIRE (F) out
through the SIDE ACCESS HOLE.
6. With the HANDLEBAR TUBE (H) facing the rear of the unit
as shown, slide the MONOCOLUMN (E) into the MONO-
COLUMN BRACKET (L) of the BASE UNIT (C). Slide the
MONOCOLUMN down until it is fully seated. Secure the
MONOCOLUMN to the MONOCOLUMN BRACKET using
two 3-15/16" HEX HEAD BOLTS (3) and three THICK FLAT
WASHERS (4) (as shown) from the rear side of the MONO-
COLUMN and two 2-3/8" HEX HEAD BOLTS (5) and THICK
FLAT WASHERS (4) from the user left side of the MONO-
COLUMN BRACKET. Tighten the BOLTS securely.
NOTE: Be careful not to let the CONNECTOR (W) fall into
the DISLAY CONSOLE BRACKET (X).
15. Locate the HANDLEBAR ASSEMBLY (Y). With the handle-
bars facing forward, position the HANDLEBAR ASSEMBLY
near the top of the HANDLEBAR TUBE (H). Slide the HAN-
DLEBAR ASSEMBLY fully into the HANDLEBAR TUBE.
Secure the HANDLEBAR ASSEMBLY to the HANDLEBAR
TUBE using four 5/8" BUTTON HEAD SCREWS (12) and
matching FLAT WASHERS (13). Tighten the SCREWS
securely.
CAUTION: Be careful not to pinch the WIRE (M) leading
from the MONOCOLUMN BRACKET (L) when inserting
the MONOCOLUMN (E) into the MONOCOLUMN
BRACKET.
16. Locate the RIGHT PEDAL (Z) (marked with an "R") and
PEDAL STRAP (AA) (marked with an "R"). With the side of
the PEDAL STRAP marked with an “R” facing upward, slide
the slotted end of the PEDAL STRAP through the left slot in
the PEDAL. Fasten one of the slots onto the TAB located
under the left slot of the PEDAL. Bend the PEDAL STRAP
upward and slide the remaining end of the PEDAL STRAP
through the right slot in the PEDAL and into the STRAP
ADJUSTMENT CLIP. The PEDAL STRAP should securely
engage the STRAP ADJUSTMENT CLIP.
7. Connect the WIRE (M) leading from the MONOCOLUMN
BRACKET (L) to the corresponding WIRE (F) from the SIDE
ACCESS HOLE (K) of the MONOCOLUMN (E). Slide the
MONOCOLUMN COVER (G) downward to the meet the
MAIN SHROUDS (N). Secure the MONOCOLUMN COVER
to the MAIN SHROUDS using four 1/2" PHILLIPS SCREWS
(6) and matching FLAT WASHERS (7). Tighten the
SCREWS securely. Do not overtighten the SCREWS.
8. Locate the SEAT (O) and SEAT POST (P). Remove the
three NYLOCK NUTS (8) and FLAT WASHERS (9) from the
threaded studs on the bottom of the SEAT. Align the three
threaded studs of the SEAT with the mounting holes in the
SEAT POST MOUNTING PLATE (Q). Secure the SEAT to
the SEAT POST MOUNTING PLATE using the three previ-
ously removed NYLOCK NUTS and FLAT WASHERS.
Tighten the NUTS securely.
17. Install the RIGHT PEDAL (Z) to the USER RIGHT CRANK
ARM (BB). Repeat for the LEFT PEDAL (CC) (marked with
an "L") and PEDAL STRAP (DD) (marked with an "L").
NOTE: The LEFT PEDAL (CC) has reverse threads.
18. Locate the WATER BOTTLE BRACKET (EE). Secure the
WATER BOTTLE BRACKET to the underside of the HAN-
DLEBAR TUBE (H) using two 3/8" PHILLIPS SCREWS (14).
Tighten the screws securely. Insert the WATER BOTTLE
(FF) into the WATER BOTTLE BRACKET.
9. Locate the SEAT POST CAP (R). With the curved side fac-
ing upward toward the SEAT (O) and the inside notch
aligned with the SEAT POST ADJUSTMENT DECAL, slide
the SEAT POST CAP over the SEAT POST (P).
19. Position the unit in the desired location for use. The unit can
be easily moved into place by lifting the rear of the unit and
rolling it on the front rollers. Level the unit before use. Refer
to the leveling instructions stated in the operations portion of
this manual.
10. Locate and slide the SEAT POST SPACER (S) over the end
of the SEAT POST (P). Using two 1/4" PHILLIPS SCREWS
(10), secure the SEAT POST SPACER to the end of the
SEAT POST. Tighten the SCREWS securely.
20. Locate the AC POWER ADAPTER. Plug the BARREL CON-
NECTOR (GG) into the JACK located at the bottom rear of
the bike. Plug the AC ADAPTER (HH) into an electrical out-
let that has been properly installed and grounded in accor-
dance with all local codes and ordinances manual.
11. With the nose of the SEAT (O) facing forward, insert the
SEAT POST (P) into the SEAT POST SUPPORT (T).
5
Download from Www.Somanuals.com. All Manuals Search And Download.
UNPACKING THE RECUMBENT EXERCISE BIKE
1. Carefully cut and remove the SHIPPING BANDS.
2. Carefully cut the tape securing the TOP FLAPS.
3. Fold the TOP FLAPS outward fully.
4. With the help of another person, remove the SIDE SHIPPING TRAY.
CAUTION: Be sure to keep the left and right sides of the SIDE SHIPPING TRAY together while removing it from
the SHIPPING CARTON.
5. Remove the DISPLAY CONSOLE carton and the ACCESSORY TRAY from beside the BASE UNIT.
6. With the help of another person, lift the BASE UNIT from the SHIPPING CARTON. Remove the protective packaging
from the unit.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
13. With the HANDLEBAR TUBE (T) facing the rear of the unit as
shown, slide the MONOCOLUMN (O) into the MONOCOLUMN
BRACKET (W) of the BASE UNIT (C). Slide the MONOCOL-
UMN down until it is fully seated. Secure the MONOCOLUMN
to the MONOCOLUMN BRACKET using two 3-15/16" HEX
HEAD BOLTS (13) and three THICK FLAT WASHERS (14) (as
shown) from the front side of the MONOCOLUMN and two 2-
3/8" HEX HEAD BOLTS (15) and THICK FLAT WASHERS
(14) from the user left side of the MONOCOLUMN BRACKET.
Tighten the BOLTS securely.
ASSEMBLING THE RECUMBENT
EXERCISE BIKE
Tools Required: Metric Wrench Set, Metric Allen
Wrench Set, Phillips Screwdriver
1. Locate and install the two LEVELER FEET (A) to the bottom of
the REAR STABILIZER (B).
2. Attach the REAR STABILIZER (B) to the BASE UNIT (C) using
two 2-3/8" BUTTON HEAD SCREWS (1) from the top of the
REAR STABILIZER BRACKET (D) and two 13/16" BUTTON
HEAD SCREWS (2) from the front side of the REAR STABI-
LIZER BRACKET. Tighten the SCREWS securely.
CAUTION: Be careful not to rinch the WIRE (X) leading
from the MONOCOLUMN BRACKET (W) when inserting
the MONOCOLUMN (O) into the MONOCOLUMN
BRACKET.
14. Connect the WIRE (X) leading from the MONOCOLUMN
BRACKET (W) to the corresponding WIRE (P) from the SIDE
ACCESS HOLE (V) of the MONOCOLUMN (O). Slide the
MONOCOLUMN COVER (S) downward to the meet the MAIN
SHROUDS (Y). Secure the MONOCOLUMN COVER to the
MAIN SHROUDS using four 1/2" PHILLIPS SCREWS (12) and
matching FLAT WASHERS (16). Tighten the SCREWS secure-
ly. Do not overtighten the SCREWS.
3. Locate the HANDLEBAR ASSEMBLY (E) and the SEAT
ASSEMBLY (F). With the handlebars facing upward and for-
ward, align the mounting holes of the HANDLEBAR ASSEM-
BLY with those in the SEAT ASSEMBLY. Secure the HANDLE-
BAR ASSEMBLY to the SEAT ASSEMBLY using four 5/8"
BUTTON HEAD SCREWS (3) and FLAT WASHERS (4).
Tighten the SCREWS securely.
4. Locate the SEAT BOTTOM (G). Align the SEAT BOTTOM
mounting holes with those in the LOWER SEAT SUPPORT
TUBES (H). Secure the SEAT BOTTOM using four 2"
PHILLIPS SCREWS (5) and LOCK WASHERS (6). Tighten the
SCREWS securely.
15. Remove the DISPLAY CONSOLE (Z) from its shipping carton.
While holding the CONNECTOR (AA), cut the wire tie securing
the CONNECTOR to the DISPLAY CONSOLE BRACKET
(BB). Position the DISPLAY CONSOLE above the DISPLAY
CONSOLE BRACKET. Connect the CONNECTOR (Z) leading
from the DISPLAY CONSOLE BRACKET to the corresponding
JACK(s) located on the back of the DISPLAY CONSOLE.
Secure the DISPLAY CONSOLE to the DISPLAY CONSOLE
BRACKET using four 1/2" PHILLIPS SCREWS (12). Tighten
the SCREWS securely. Do not overtighten the SCREWS.
5. Align the guide rollers located on the underside of the SEAT
ASSEMBLY (F) with the SEAT EXTRUSION (J). Carefully
guide the SEAT ASSEMBLY onto the SEAT EXTRUSION.
Slide the SEAT ASSEMBLY fully forward.
6. In the hole located in the user right side of the SEAT EXTRU-
SION (J), behind SEAT ASSEMBLY (F), install one 1-3/8"
BUTTON HEAD SCREW with locktite (7), two 15/16" FLAT
WASHERS (8), one RUBBER BUMPER SLEEVE (9) and one
1" RUBBER BUMPER (10) as shown.
NOTE: Be careful not to let the CONNECTOR (AA) fall into the
DISLAY CONSOLE BRACKET (BB).
16. Locate the RIGHT PEDAL (CC) (marked with an "R") and
PEDAL STRAP (DD) (marked with an "R"). With the side of the
PEDAL STRAP marked with an “R” facing upward, slide the
slotted end of the PEDAL STRAP through the left slot in the
PEDAL. Fasten one of the slots onto the TAB located under
the left slot of the PEDAL. Bend the PEDAL STRAP upward
and slide the remaining end of the PEDAL STRAP through the
right slot in the PEDAL and into the STRAP ADJUSTMENT
CLIP. The PEDAL STRAP should securely engage the STRAP
ADJUSTMENT CLIP.
7. Mount the SEAT ADJUSTMENT LEVER (K) to the user right
side of the SEAT ASSEMBLY (F) using two 3/4" PHILLIPS
SCREWS (11). Tighten the SCREWS securely.
8. Secure the SEAT BACK (L) to the UPPER SEAT SUPPORT
TUBES (M) using four 2" PHILLIPS SCREWS (5) and LOCK
WASHERS (6). Tighten the SCREWS securely.
9. Locate the SEAT EXTRUSION ENDCAP (N). Secure the SEAT
EXTRUSION ENDCAP to the SEAT EXTRUSION (J) using
two 1/2" PHILLIPS SCREWS (12).
17. Install the RIGHT PEDAL (EE) to the USER RIGHT CRANK
ARM (DD). Repeat for the LEFT PEDAL (FF) (marked with an
"L") and PEDAL STRAP (GG) (marked with an "L").
10. Locate the MONOCOLUMN (O). Cut the WIRE TIE securing
the WIRE (P) to the bottom of the MONOCOLUMN. Slide the
MONOCOLUMN COVER (Q) onto the MONOCOLUMN (E) as
shown. Slide the MONOCOLUMN COVER up to the HANDLE-
BAR TUBE (T).
NOTE: The LEFT PEDAL (FF) has reverse threads.
18. Locate the WATER BOTTLE BRACKET (HH). Secure the
WATER BOTTLE BRACKET to the underside of the MONO-
COLUMN (O) using two 3/8" PHILLIPS SCREWS (17). Tighten
the screws securely. Insert the WATER BOTTLE (HH) into the
WATER BOTTLE BRACKET.
11. Slide the MONOCOLUMN COVER (S) onto the MONOCOL-
UMN (O) as shown. Slide the MONOCOLUMN COVER up to
the HANDLEBAR TUBE (T).
19. Position the unit in the desired location for use. The unit can
be easily moved into place by lifting the rear of the unit and
rolling it on the front rollers. Level the unit before use. Refer to
the leveling instructions stated in the operations portion of this
manual.
12. Locate and insert the GROMMET (U) into the SIDE ACCESS
HOLE (V) of the MONOCOLUMN (O). Pull the WIRE (P) out
through the SIDE ACCESS HOLE.
20. Locate the AC POWER ADAPTER. Plug the BARREL CON-
NECTOR (KK) into the JACK located at the bottom rear of the
bike. Plug the AC ADAPTER (LL) into an electrical outlet that
has been properly installed and grounded in accordance with
all local codes and ordinances manual.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
This Operation Manual describes the functions of the following products:
Bally® upright exercise bike:
CU300
Bally recumbent exercise bike:
CR300
See Section 7, titled Specifications page in this manual
for product-specific features.
Statement of Purpose: The exercise bike is a machine that simulates the movements of riding a bicycle at various
speeds and levels of resistance.
Health-related injuries may result from incorrect or excessive use of exercise equipment. The manufacturer
STRONGLY recommends seeing a physician for a complete medical exam before undertaking an exercise
program, particularly if the user has a family history of high blood pressure or heart disease; or is over the
age of 45; or smokes, has high cholesterol, is obese, or has not exercised regularly in the past year. The
manufacturer also recommends consulting a fitness professional on the correct use of this product.
If, at any time while exercising, the user experiences faintness, dizziness, pain, or shortness of breath, he or
she must stop immediately.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
1
GETTING STARTED
1.1 IMPORTANT SAFETY INSTRUCTIONS
SAFETY WARNING: The safety of the product can be maintained only if it is examined regularly for
damage and wear. See Preventative Maintenance section for details.
•
Before using this product, it is essential to read this ENTIRE operation manual and ALL instructions. The bike is
intended for use solely in the manner described in this manual.
•
•
•
Always follow the console instructions for proper operation.
Close supervision is necessary when used by or near children, invalids or disabled persons.
If a bike does not function properly after it has been dropped, damaged, or even partially immersed in water, contact
Customer Support Services for assistance.
•
•
Never insert objects into any opening in the bike. If an object should drop inside, carefully retrieve it. If the item is
beyond reach, contact Customer Support Services.
Never place liquids of any type directly on the unit, except in an accessory tray. Containers with lids are
recommended.
•
•
•
•
Do not use the bike outdoors, near swimming pools or in areas of high humidity.
Keep all loose clothing, shoelaces, and towels away from the bike pedals.
Keep the area around the bike clear of any obstructions, including walls and furniture.
Always be careful and exercise caution when mounting or dismounting the bike. Use the handlebar whenever
additional stability is required.
•
Wear shoes with rubber or high-traction soles. Do not use shoes with heels, leather soles, cleats or spikes. Do not
use the bike in bare feet.
•
•
•
Do not tip the bike on its side during operation.
Keep hands and feet away from all moving parts.
To ensure proper functioning of this product, do not install attachments or accessories that are not provided or
recommended by Life Fitness.
•
•
•
Use this product in a well-ventillated area.
Use this product on a solid, level surface.
Make sure that all components are fastened securely. These include the seat post, saddle, handlebars, and pedals.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
1.2 SETUP
Read the entire Operation Manual before setting up the Bally exercise bike.
WHERE TO PLACE THE BALLY® EXERCISE BIKE
Following all safety instructions in Section 1.1, move the bike to the location in which it will be used. See Section 7, titled
Specifications, for the dimensions of the footprint. Allow a distance of four feet, or 120 centimeters, between the bike and
other objects or surfaces on either side.
HOW TO STABILIZE THE BALLY EXERCISE BIKE
After placing the bike in position, check the unit's stability by attempting to rock it in all directions. Any slight rocking indicates
that the unit must be leveled. Determine which foot is not resting completely on the floor. Loosen the jam nut with an open-end
17mm wrench, and rotate the stabilizing foot to lower it. Verify that the bike is stable, and repeat the adjustment as necessary
until the unit no longer rocks. Lock the adjustment by tightening the jam nut against the stabilizer bar.
HOW TO ADJUST THE SEAT
Proper seat positioning minimizes unecessary leg muscle fatigue. To determine whether or not the seat requires adjust-
ment, sit on it and place the balls of the feet on the pedals. The knee should bend slightly when the pedal is at the
furthest point in its rotation, relative to the body. The user should be able to pedal without locking the knees or shifting in
the seat.
Adjusting the seat on the upright bike: The bike post features a vertical locking pin seat adjustment system, which
makes it easy and safe to change the height of the seat quickly.
To raise the seat, first get off the bike. Hold the seat, turn the spring-loaded knob on the right of the seat post
once counter-clockwise to loosen it, and pull out the knob to unlock the post from its present position. Pull the seat
upward to the desired height, and release the knob to let it lock into place. Turn the knob once clockwise to tighten it.
Test and re-adjust the seat height as necessary.
To lower the seat, first get off the bike. Hold the seat, turn the spring-loaded knob on the right of the seat post
once counterclockwise to loosen it, and pull out the knob to unlock the post from its present position. Let the seat slide
down to the desired height, and release the knob to let it lock into place. Turn the knob once clockwise to tighten it. Test
and re-adjust the seat height as necessary.
CAUTION: When using the height adjustment mechanism to change the height of a partially raised seat,
hold the seat to prevent it from falling on the hand.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the seat on the recumbent bike: Lift the spring-loaded adjusting handle located on the right side of the seat.
Slide the seat forward or backward as necessary to the proper position and release the pin to complete engagement.
Gently rock the seat forward and backward to ensure that it is locked into place. Check the seat distance again and re-
adjust it if necessary.
Note: If the seat carriage rocks excessively, use a wrench to loosen the jam nut (A) on either side of the seat carriage.
With another wrench, tighten the adjustment roller on the inside of the carriage until it is snug, but do not over-tighten it.
Then, while holding the roller in place, tighten the lock nut. Repeat the procedure for the other side of the seat carriage.
CAUTION: Do not attempt to adjust the seat while pedaling the bike. Doing so, or failing to insert the
seat pin completely may result in an uncomfortable workout or cause injury.
HOW TO ADJUST THE PEDAL STRAPS
The bike pedal safety straps keep the user's shoes on the pedals during a workout. The straps should fit comfortably, but
they also should be tight enough to prevent shoes from slipping at any point in the pedaling rotation. Before working out,
the user should test and adjust the tightness of the straps.
The straps can be adjusted to fit a variety of shoe sizes. Each strap is held in place by a spring-loaded clip that is con-
nected to the outer edge of each pedal. To tighten a strap, simply pull the loose end of the strap down. It automatically
locks into place with each pull. To loosen a strap, press down on the top of the clip and pull the strap up. Release the clip
to lock the strap into place. Test the adjustment, and change if necessary.
STARTING UP THE BIKE
To power up the Bally exercise bike, simply start pedaling. Once the unit’s power is on, the console display lights up, making
it possible to select a workout or to begin a QUICK START workout using. See Section 4.2, titled the Using the Workouts,
for more information.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
2
THE DISPLAY CONSOLE
2.1 DISPLAY CONSOLE OVERVIEW
The computerized display console on the exercise bike allows the user to tailor a workout to personal fitness abilities and
goals and to monitor progress. With this easy-to-use console the user can track fitness improvement from one workout to
the next.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2 DISPLAY CONSOLE DESCRIPTIONS
The functions for the keys and display windows on the exercise bike console are listed and described in this section. See
Section 4, titled The Workouts, for detailed information on using the console to set up workouts.
A
B
C
QUICK START: Press this key to begin a MANUAL workout immediately, without having to select a workout. Once
the workout is in progress, use the ARROW KEYS to change the intensity level or workout duration as desired.
MY WORKOUT: Press this key to select a MY WORKOUT custom workout, if one or more of these workouts have
been configured beforehand.
WORKOUT PROFILE: Press this key to select one of the following workouts during a workout setup:
•
•
•
•
HILL
•
•
•
OUTDOOR TRAINING
FAT BURNER (optional)
CARDIO (optional)
RANDOM
MANUAL
GRADUAL HILL
D
LEVEL ARROW keys: During a workout-in-progresss, use these keys to change the difficulty level of the workout. Also,
pressing these keys during a FAT BURNER (optional), or CARDIO (optional), workout increases or decreases the target
heart rate.
During a workout setup, use these keys tochange displayed values for workout type, duration, and difficulty level.
E
F
ENTER: Press this key after entering each value, such as weight or workout time, when prompted by console display
messages.
CLEAR/PAUSE:
CLEAR: Press this key, when programming a workout, to clear incorrect data, such as weight or age, before pressing
the ENTER key. Pressing CLEAR three times consecutively during a workout stops it immediately, at which point, the
MESSAGE CENTER prompts the user for a new workout setup.
PAUSE: Press this key to pause a workout in progress. Press ENTER to continue the workout. If a paused workout
is not resumed within the preset pause duration, the computer deletes the in-progress workout information and
returns to a workout setup state: The MESSAGE CENTER displays “SELECT WORKOUT PROFILE OR PRESS
QUICK START”.
G
H
COOL DOWN: Workouts end automatically in a Cool Down mode, which lowers the intensity level. Press the COOL
DOWN key at any desired point during a workout to go immediately into Cool Down mode. In this phase of a workout
the body begins to remove lactic acid and other accumulated by-products of exercise, which build up in muscles dur-
ing a workout and contribute to muscle soreness. The console automatically adjusts each workout’s Cool Down level
according to the individual user’s performance. Each time the user presses the COOL DOWN key, the Cool Down
duration shortens by one minute.
WORKOUT PROFILE WINDOW: This window displays shapes, made of columns of lights, that represent the levels
of intensity in a workout-in-progress. The higher the column, the greater the intensity.
During a FAT BURNER (optional) or CARDIO (optional), workout, the bike requires the use of a telemetryheart rate chest
strap to detect a heart rate. If the console does not detect a signal, the MESSAGE CENTER displays the prompt, "NEED
HEART RATE - CHECK TELEMETRY STRAP". If the console does not receive the signal within three minutes, the work-
out automatically is converted to a MANUAL workout. Profiles are not available for FAT BURNER or CARDIO workout. In
these workouts, the level is based on the heart rate. Therefore, the profile cannot be displayed.
I
TIME ARROW keys: During a workout-in-progresss, use these keys to change the duration.
During a workout setup, use these keys to change displayed values for workout type, duration, and difficulty level.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
J
WORKOUT LED INDICATORS: A set of LEDs is matched to a set of workout statistics that are displayed during a
workout-in-progress. See the MESSAGE CENTER description above. Each LED lights up when the corresponding
statistic, such as Calories, is being displayed.
K
MESSAGE CENTER: This window displays step-by-step instructions for setting up a workout. When a workout is in
progress, it displays statistics about the progress of the workout, as seen below:
•
Time/Zone: the amount time of time that the user has maintained a heart rate within a target zone if the user is
wearking a telemetry heart rate chest strap
•
•
•
Cool Down: the time elapsed since a workout-in-progress has gone into cool-down mode
Heart Rate: detected heart rate if the user is wearing the Polar heart rate chest strap
Speed: the pedaling speed or rate in Revolutions Per Minute (RPM)
•
Heart Rate Percent: the user’s heart rate expressed as a percent of the theoretical maximum heart rate if the
user is wearing a telemetry heart rate chest strap
•
•
•
•
Distance: the total distance traveled since the beginning of the workout
Calories per hour: the rate of calories burned per hour
Calories: the number of calories burned since beginning the workout
Time: the time elapsed since the start of the workout
2.3 THE ACCESSORY TRAY (OPTIONAL) AND READING RACK
The accessory tray (A), which is mounted below the base of the console, provides dual storage trays with space for items
such as water bottles, personal stereos, and cell phones.
Additionally, an integrated reading rack (B) for supporting a book or magazine is located at the base of the console.
Upright model pictured
14
Download from Www.Somanuals.com. All Manuals Search And Download.
3
HEART RATE ZONE TRAINING EXERCISE
3.1 WHY HEART RATE ZONE TRAINING EXERCISE?
Research shows that maintaining a specific heart rate while exercising is the optimal way to monitor the intensity of a
workout and to achieve maximum results. That is the idea behind heart rate zone training approach to exercise.
Zone training identifies an exerciser's ideal heart rate range, or zone, for burning fat or increasing cardiovascular fitness.
The values within the zone depend on the workout.
NOTE: Consulting a fitness trainer is recommended for defining specific fitness goals and designing a workout program.
The exercise bike features two workouts that are designed to take full advantage of the benefits of heart rate zone train-
ing exercise: FAT BURNER and CARDIO. For detailed information about these workouts, see Section 4, titled The
Workouts. These workouts become enabled if an optional telemetry kit is purchased and installed. See the
following section, titled Heart Rate Monitoring, for more information.
During one of these workouts, wear the optional telemetry heart rate chest strap to enable the exercise bike’s on-board com-
puter to monitor the heart rate. The computer automatically adjusts the resistance level to maintain the target heart rate*
based on the actual heart rate. To change the target heart rate during a workout, use the
ARROW keys.
* Target Heart Rate (THR) is a percentage of the theoretical maximum. For example, a 40-year-old user's THR for the CARDIO workout is 144. This workout
targets 80 percent of the maximum, so the equation would be (220-40)*.80=144. A 20-year-old user’s THR is 160, so the equation would be
(220-20)*.80=160.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2 HEART RATE MONITORING
THE TELEMETRY HEART RATE CHEST STRAP (OPTIONAL)
The Bally exercise bike can be equipped with telemetry, a heart rate monitoring system in which electrodes, pressed
against the skin, transfer heart rate signals to the exercise bike console. These electrodes are attached to a heart rate
chest strap that the user wears during the workout. Telemetry and the chest strap are optional. To order them, contact
Customer support. See section 6.4, titled How to Obtain Product Service.
See the diagram below for correct positioning of the strap. The electrodes (A), which are the two grooved surfaces on
the underside of the strap, must remain wet to transmit accurately the electrical impulses of the heart back to the receiv-
er. Moisten the electrodes. Then, secure the strap as high under the chest muscles as possible. The strap should be
snug, but comfortable enough to allow for normal breathing.
The transmitter strap delivers an optimal heart rate reading when the electrodes are in direct contact with skin. However,
it also functions properly through a thin layer of wet clothing.
If it becomes necessary to re-moisten the chest strap electrodes, grasp the center of the strap, pull it away from the
chest to expose the two electrodes, and moisten them.
A
A
16
Download from Www.Somanuals.com. All Manuals Search And Download.
4
THE WORKOUTS
4.1 WORKOUT OVERVIEWS
This section lists the Lifecycle exercise bike’s pre-programmed workouts. For more detailed information, see Section 4.2,
titled Using the Workouts.
QUICK START is the fastest way to begin exercising, and it bypasses the steps involved in selecting a specific workout
program. After the QUICK START key is pressed, a constant-level workout begins. The intensity level does not change
automatically.
HILL is an interval-training workout combining “hills” and “valleys” of different intensity levels, which is proven to provide
effective, time-efficient cardiovascular results.
RANDOM is an interval training workout of constantly changing intensity levels that occur in no regular pattern or pro-
gression.
MANUAL is a workout in which the intensity level does not change automatically.
OUTDOOR TRAINING simulates an outdoor cycling terrain by setting different hills, or intensity levels, throughout the
course.
GRADUAL HILL features a gradual, subtle increase in resistance, lowering perceived exertion. A peak in resistance is
followed by an equally subtle decrease in resistance.
FAT BURNER (optional) is a low-intensity workout for burning the body’s fat reserves. The user must wear a telemetry
heart rate chest strap. The workout program automaticaly adjusts the intensity level, based on the actual heart rate, to
†
maintain the rate at 65 percent of the theoretical maximum .
CARDIO (optional) is a higher intensity workout for more fit users, emphasizing cardiovascular benefits and maximum fat burn-
ing. The user must wear a telemetry heart rate chest strap. The workout program automatically adjusts the intensity level,
based on the actual heart rate, to maintain the rate at 80 percent of the theoretical maximum.
4.2 USING THE WORKOUTS
Different workouts require different setup steps. See the chart titled Bally Exercise Bike Workout Set-up Steps, which
appears later in this section, for a quick glance at the steps for setting up any workout. This section provides details on
the steps themselves.
TO BEGIN ANY WORKOUT
Simply start pedaling to activate the console. The MESSAGE CENTER displays the prompt: “SELECT WORKOUT USING
ARROW KEYS OR PRESS QUICK START”. If it displays a different message, press the CLEAR key twice rapidly.
SELECTING QUICK START
QUICK START is the fastest way to begin exercising, and it bypasses the steps involved in selecting a specific workout.
Simply press the QUICK START key to begin a constant-level workout begins. As with a MANUAL workout, the intensity
level for does not change automatically.
SELECTING A WORKOUT
For HILL, RANDOM, MANUAL, OUTDOOR TRAINING, GRADUAL HILL, FAT BURNER (optional), and CARDIO (optional):
When prompted to select a workout, use the WORKOUT PROFILE key to scroll through the options displayed in the MES-
SAGE CENTER. Then, use the ARROW keys to scroll through the workout names as they appear in the MESSAGE CEN-
TER. When the desired workout appears, press ENTER.
ENTERING A DURATION
When prompted by the MESSAGE CENTER to enter a time, use the ARROW KEYS to increase or decrease the dis-
played time to the desired value, and press ENTER.
†
Defined by the American College of Sports Medicine's "Guidelines for Exercise Testing and Prescription" as equal to 220 minus an individual’s age.
* Target Heart Rate (THR) is a percentage of the theoretical maximum. For example, a 40-year-old user's THR for the CARDIO workout is 144. This workout
targets 80 percent of the maximum, so the equation would be (220-40)*.80=144. A 20-year-old user’s THR is 160, so the equation would be
(220-20)*.80=160.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
ENTERING AGE
When prompted by the MESSAGE CENTER to enter age, use the ARROW KEYS to increase or decrease the displayed
age to the correct value, and press ENTER.
Lifecycle exercise bike workout programs that set a target heart rate* zone first calculate the user’s theoretical maximum
†
heart rate by subtracting the user’s age from the number 220. The programs then calculate the target zone as a per-
centage of the theoretical maximum.
SELECTING THE DIFFICULTY LEVEL OR TARGET HEART RATE
For HILL, RANDOM, OUTDOOR TRAINING, and GRADUAL HILL: After a duration is entered, the MESSAGE CENTER
flashes a default difficulty level of “1”, which is the easiest of the 20 difficulty levels. Press ENTER to accept the default. Or, to
change the level, use the ARROW keys. Then, when the desired level appears in the DATA WINDOW, press ENTER to accept
the duration. Each of the 20 difficulty levels corresponds to a range of resistance levels as seen in the table below. A
resistance level is applied to each individual interval within a workout profile. See Section 3.3, titled Workout Descriptions
for more information. While the workout is in progress, it is possible to change the difficulty level.
Difficulty
Level
Resistance
Level Range
Difficulty
Level
Resistance
Level Range
1
2
1 to 1
1 to 2
1 to 3
1 to 4
1 to 5
2 to 6
2 to 7
2 to 8
2 to 9
2 to 10
11
12
13
14
15
16
17
18
19
20
3 to 11
3 to 12
3 to 13
3 to 14
3 to 15
4 to 16
5 to 17
6 to 18
7 to 19
8 to 20
3
4
5
6
7
8
9
10
For FAT BURNER (optional) and CARDIO (optional): After a duration is entered, the MESSAGE CENTER displays a tar-
get heart rate*, which is based on the entered age. Press ENTER to select the displayed rate, or use the ARROW keys
to change the rate, and then press ENTER. When the workout is in progress, it is possible to change the target heart
rate using the level arrow keys.
Note: With the exercise bike’s braking resistance feature, the resistance level increases proportionally with the pedaling speed.
BALLY EXERCISE BIKE WORKOUT SETUP STEPS
QUICK START
Select QUICK START
Begin workout
MANUAL
Select MANUAL
GRADUAL HILL
Select GRADUAL HILL
Select time
CARDIO* (optional)
Select CARDIO
Enter time
Enter time
Enter difficulty level
Begin workout
Select difficulty level
Begin workout
Enter age
Accept THR**
Begin workout
HILL
Select HILL
Enter time
Select difficulty level
Begin workout
OUTDOOR TRAINING
Select OUTDOOR
TRAINING
FAT BURNER* (optional)
Select FAT BURNER
Enter time
Select time
Select level
Begin workout
Enter age
Accept THR**
Begin workout
RANDOM
Select RANDOM
Enter time
Enter difficulty level
Begin workout
* This workout requires the user to wear the telemetry chest strap.
** Target Heart Rate (THR) is a percentage of the theoretical maximum. For example, a 40-year-old user's THR for the CARDIO workout is 144.
This workout targets 80 percent of the maximum, so the equation would be (220-40)*.80=144. A 20-year-old user’s THR is 160, so the equation would
be (220-20)*.80=160.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
PAUSING WORKOUTS
To pause a workout, press the CLEAR/PAUSE key. Pedalling must not cease. PAUSE will eliminate resistance during
the pause duration. To continue the workout, press the ENTER key.
INITIATING AN EARLY COOL-DOWN
Workouts end automatically in a Cool Down mode, which lowers the intensity level. Press the COOL DOWN key at any
desired point during a workout to go immediately into Cool Down mode. In this phase of a workout the body begins to remove
lactic acid and other accumulated by-products of exercise, which build up in muscles during a workout and contribute to
muscle soreness. The console automatically adjusts each workout’s Cool Down level according to the individual user’s
performance. Each additional time the user presses the COOL DOWN key, the resistance level shortens by half. It is possible
to change the Cool Down duration by pressing the TIME ARROW keys.
ENDING WORKOUTS EARLY
To end a workout before the pre-set duration expires, press CLEAR/PAUSE key three times. The MESSAGE CENTER dis-
plays “SELECT WORKOUT PROFILE OR PRESS QUICK START” for a new workout.
4.3 WORKOUT DESCRIPTIONS
QUICK START
QUICK START is the fastest way to begin exercising, and it bypasses the steps of selecting a specific workout. The
intensity level for the workout is set automatically and remains the same unless manually changed. To change the level
press the UP or DOWN ARROW keys. If the CALORIES PER HOUR display is enabled, the MESSAGE CENTER dis-
plays ENTER WEIGHT, which is required to calculate this ratio. Using the ARROW KEYS, increase or decrease the dis-
played weight to the correct value.
HILL
The HILL workout features intervals of intense aerobic activity separated by intervals of lower-intensity. Interval training
has been scientifically demonstrated to yield greater cardiorespiratory improvement than steady-pace training.
During the Hill workout the difficulty level of intervals increases gradually, as the profile diagram below illustrates.
†
Defined by the American College of Sports Medicine's "Guidelines for Exercise Testing and Prescription" as equal to 220 minus an individual’s age.
* Target Heart Rate (THR) is a percentage of the theoretical maximum. For example, a 40-year-old user's THR for the CARDIO workout is 144. This workout
targets 80 percent of the maximum, so the equation would be (220-40)*.80=144. A 20-year-old user’s THR is 160, so the equation would be
(220-20)*.80=160.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Each workout session includes the following phases:
1
2
3
Warm-up gradually brings the heart rate into the lower portion of the target heart rate zone, increasing respiration
and blood flow to working muscles.
Plateau increases heart rate to bring it is within the target zone. To check the heart rate grasp the handpulse sen-
sors or wear the telemetry heart rate chest strap.
Interval Training is a series of hills and valleys. During this portion of the workout, the user is confronted with a
series of successively steeper hills, each separated from the next by a valley or recovery period. Again, check the
heart rate to ensure that it has remained within the target zone.
4
Cool-down allows the body to begin removing accumulated by-products of exercise, such as lactic acid, which build
up in muscles during a workout and contribute to muscle soreness.
Effort and recovery periods are simulated on the display console by columns of red lights in the workout Profile window.
Each column represents one interval and 20 intervals make up a workout. The columns move from right to left during the
workout. The higher the column, the higher the resistance. The intervals are all of equal length, and interval duration
depends on the overall duration of the workout.
1 to 9 minutes: Because workouts with durations of less than 10 minutes are insufficient for the HILL workout to
complete all four phases adequately, the profile is condensed at various stages.
10 to 19 minutes: The interval durations are initially set at 30 seconds for a 10-minute workout. For every additional
minute of workout duration intervals lengthen by three seconds. Thus, a 15-minute HILL workout features 20 intervals of
45 seconds each.
20 to 99 minutes: All intervals last 60 seconds. As minutes are added, additional hills and valleys are presented beyond
the initial four of the interval training phase. The additional hills and valleys will follow the form of the first four, dropping
back down to the level of the very first hill encountered and progressing in height every two minutes until the highest hill
is reached again. This process repeats until the end of the duration.
RANDOM
The RANDOM workout creates a terrain of hills and valleys that varies with each workout. More than one million different
patterns are possible.
MANUAL
The MANUAL workout sets an intensity level that does not change automatically. While the workout is in progress, increase
or lower the intensity level as desired, using the arrow keys.
OUTDOOR TRAININGTM WORKOUT
OUTDOOR TRAINING is based on a RANDOM workout profile with smoother transitions between hills and valleys. This
workout simulates conditions of an outdoor cycling terrain.
During the workout setup, the chosen difficulty level corresponds to the baseline, or flat ground, for the workout. Any
difficulty level above this baseline simulates pedaling uphill. Any difficulty level below the baseline simulates pedaling
downhill.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
GRADUAL HILL
In this workout, the gradual changes in resistance are extremely subtle, lowering perceived exertion. The changes in
resistance also are independent of the user’s pedaling speed. The cardiovascular workout is effective, efficient, and
enjoyable at the same time.
The workout consists of one hill. The user determines the height of the peak of this hill by selecting an intensity level during
the setup. The higher the level selected, the higher the intensity at the entry point, which is the beginning of the workout,
and the higher the intensity at the peak, which occurs after 75 percent of the workout is completed.
After the peak is reached, the resistance gradually returns to the same intensity level as that of the entry point. See the
chart below.
GRADUAL HILL Workout Profile
0% Time
(Entry point)
75% Time
(Peak)
100% Time
(End point)
FAT BURNER (OPTIONAL)
†
The FAT BURNER workout is designed to maintain a user’s heart rate at 65 percent of the theoretical maximum rate for opti-
mal results. Throughout the workout, the user wears a telemetry heart rate chest strap. The console continuously monitors
and displays the heart rate, adjusting the intensity level of the exercise bike to reach and maintain the target*. This system
eliminates over- and under-training, and it maximizes the aerobic benefits of exercise by using the body's fat stores for fuel.
CARDIO (OPTIONAL)
The CARDIO workout is virtually identical to FAT BURNER; however the target heart rate is calculated at 80 percent of
†
the theoretical maximum . The higher target promotes cardiovascular improvement by placing a heavier workload on the
heart muscle. hroughout the workout, the user wears a telemetry heart rate chest strap.
†
Defined by the American College of Sports Medicine's "Guidelines for Exercise Testing and Prescription" as equal to 220 minus an individual’s age.
* Target Heart Rate (THR) is a percentage of the theoretical maximum. For example, a 40-year-old user's THR for the CARDIO workout is 144. This workout
targets 80 percent of the maximum, so the equation would be (220-40)*.80=144. A 20-year-old user’s THR is 160, so the equation would be
(220-20)*.80=160.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
5
OPTIONAL SETTINGS
Use the Optional Settings feature to change default settings or to enable or disable certain programs or displays on the
Lifecycle Exercise Bike console.
ENTERING AND USING THE OPTIONAL SETTINGS FEATURE
Press the Pause/Clear key twice, and then press Enter. The console beeps three times, and the MESSAGE CENTER
displays the first of a series of optional settings. To scroll through the settings, press ENTER repeatedly. Use the
ARROW keys to change any displayed setting, and then press ENTER to accept the change and to scroll to the next
item. The table below lists the settings, their variable values, their default values, and their definitions.
OPTIONAL SETTINGS
Setting
Variables
Default Value
Description
Hold Time
1-99 seconds
10 seconds
The number of seconds before the MESSAGE
CENTER scrolls to the next selection
The type of units in which workout statistics are
displayed
Units
English/Metric
English
Software
The current software revision for the console
computer
22
Download from Www.Somanuals.com. All Manuals Search And Download.
6
SERVICE AND TECHNICAL DATA
6.1 PREVENTATIVE MAINTENANCE TIPS
The exercise bike is backed by engineering excellence and is one of the most rugged and trouble-free pieces of exercise
equipment on the market today. The manufacturer’s products have proven to be durable in health clubs, colleges, military
facilities, and other locations the world over. This same technology, engineering expertise, and reliability have gone into
the exercise bike.
NOTE: The safety of the equipment can be maintained only if the equipment is examined regularly for damage or wear.
If maintenance is required, keep the equipment out of use until defective parts are repaired or replaced. Pay special atten-
tion to parts that are subject to wear as outlined in the Preventive Maintenance Schedule.
The following preventive maintenance tips will keep the exercise bike operating at peak performance:
•
•
•
•
Locate the exercise bike in a cool, dry place.
Clean the top surface of the pedals regularly.
Keep the display console free of fingerprints and salt build-up caused by sweat.
Use a 100% cotton cloth, lightly moistened with water and mild liquid cleaning product, to clean the exercise
bike. Other fabrics, including paper towels, may scratch the surface. Do not use ammonia or acid-based
cleaners.
•
•
Long fingernails may damage or scratch the surface of the console; use the pad of the finger to press the selec-
tion buttons on the console.
Clean the housing thoroughly on a regular basis.
NOTE: A non-abrasive cleaner and soft cotton cloth are strongly recommended for cleaning the exterior of the unit. At no
time should cleaner be applied directly to any part of the equipment; apply the non-abrasive cleaner on a soft cloth, and
then wipe the unit.
6.2 PREVENTATIVE MAINTENANCE SCHEDULE
Follow the schedule below to ensure proper operation of the product.
Follow the schedule below to ensure proper operation of the product.
ITEM
WEEKLY
MONTHLY
BI-ANNUALLY
ANNUALLY
Display Console
Console Mounting Bolts
Accessory Tray
Frame
C
I
I
C
C
C
C
I
I
Plastic Covers
Pedals and Straps
KEY: C=Clean; I=Inspect
I
I
23
Download from Www.Somanuals.com. All Manuals Search And Download.
6.3 TROUBLESHOOTING THE OPTIONAL TELEMETRY HEART RATE CHEST STRAP
HEART RATE READING IS ERRATIC OR ABSENT ENTIRELY
•
Repeat the electrode moistening procedure on the chest strap. See Section 3.2, titled Heart Rate Monitoring for
details. The electrodes must remain wet to pick up and transmit accurate heart rate readings.
•
•
•
•
Make sure the electrodes are flat against the skin.
Wash the belt transmitter regularly with mild soap and water.
Make sure the chest strap transmitter is within three feet (91 centimeters) of the heart rate receiver.
The chest strap is battery-operated and will stop functioning when the battery runs out. Contact Customer
Support Services for instructions on how to have the chest strap replaced. See Section 6.4, titled How to Obtain
Product Service.
HEART RATE READING IS ERRATIC OR EXTREMELY HIGH
If the chest strap is worn near sources of electromagnetic signals, these signals may be strong enough to elevate heart
rate readings. Possible sources include:
•
Television sets and/or antennas, cell phones, computers, cars, high voltage power lines and motor driven exer-
cise equipment.
•
Another heart rate transmitter within three feet, or one meter, may also cause abnormal heart rate readings.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
6.4 HOW TO OBTAIN PRODUCT SERVICE
1. Verify the symptom and review the operating instructions. The problem may be unfamiliarity with the product and its
features and workouts.
2. Locate and document the serial number of the unit. The serial number plate is located on the front stabilizer, below
the shroud.
3. Contact Customer Support Services via the Web at: www.lifefitness.com, or call the nearest Customer Support
Services group:
For Product Service within
the United States and Canada:
Telephone: (+1) 847.451.0036
FAX: (+1) 847.288.3702
Toll-free telephone: 800.351.3737
For Product Service Internationally:
Life Fitness Europe GmbH
Telephone: (+49) 089.317.751.66
FAX: (+49) 089.317.751.38
Life Fitness Asia Pacific Ltd
Telephone: (+852) 2891.6677
FAX: (+852) 2575.6001
Life Fitness (UK) LTD
Telephone: (+44) 1353.665507
FAX: (+44) 1353.666018
Life Fitness Latin America
and Caribbean
Telephone: (+1) 847.288.3964
FAX: (+1) 847 288.3886
Life Fitness Atlantic BV
Life Fitness Benelux
Life Fitness Brazil
Telephone: (+32) 03.644.44.88
FAX: (+32) 03.644.24.80
Telephone: (+32) 87.300.942
FAX: (+32) 87.300.943
Telephone: (+55) 11.7295.2217
FAX: (+55) 11.7295.2218
Life Fitness Japan
Telephone: (+81) 3.3359.4306
FAX: (+81) 3.3359.4307
Life Fitness Italia S.R.L.
Telephone: (+39) 0472.835.470
FAX: (+39) 0472.833.150
Life Fitness Iberia
Telephone : (+34) 93 672 4660
FAX : (+34) 93 672 4670
Toll-free telephone: 800.438836
Life Fitness Vertriebs GmbH
Telephone: (+43) 1615.7198
FAX: (+43) 1615.7198.20
25
Download from Www.Somanuals.com. All Manuals Search And Download.
7
SPECIFICATIONS
7.1 UPRIGHT EXERCISE BIKE SPECIFICATIONS
Designed use:
Maximum user weight:
CONSOLE:
Consumer
400 pounds / 181.4 kilograms
Displays:
MESSAGE CENTER displays with Time in Zone, Cool Down duration, Heart Rate,
Speed, Heart Rate Percentage of Theoretical Maximum, Distance, Calories per Hour,
and Calories
Summaries:
Time, distance
WORKOUTS:
Quick Start, Hill, Random, Manual, Outdoor Training, Gradual Hill, Fat Burner (optional),
Cardio (optional)
Heart rate monitor:
Telemetry heart rate monitoring system (optional)
Telemetry heart rate monitoring chest strap (optional)
Intensity levels:
Pedal size
20
4.5 inches / 11.5 centimeters
Poly-V belt-drive
None; bike is self-powered
Optional
Drive type:
Power requirements:
Accessory Tray:
Color:
Commercial gray
ASSEMBLED DIMENSIONS:
Length
45 inches / 114 centimeters
27.25 inches / 69 centimeters
56 inches / 142.2 centimeters
112.8 pounds / 51 kilograms
Width
Height
Weight
SHIPPING DIMENSIONS:
Length
44.88 inches / 114 centimeters
17.91 inches / 45.5 centimeters
29.92 inches / 74.3 centimeters
132.6 pounds / 60.2 kilograms
Width
Height
Weight
26
Download from Www.Somanuals.com. All Manuals Search And Download.
7.2 RECUMBENT EXERCISE BIKE SPECIFICATIONS
Designed use:
Maximum user weight:
CONSOLE:
Consumer
400 pounds / 181.4 kilograms
Displays:
MESSAGE CENTER displays with Time in Zone, Cool Down duration, Heart Rate,
Speed, Heart Rate Percentage of Theoretical Maximum, Distance, Calories per Hour,
and Calories
Summaries:
Time, distance
WORKOUTS:
Quick Start, Hill, Random, Manual, Outdoor Training, Gradual Hill, Fat Burner (optional),
Cardio (optional)
Heart rate monitor:
Telemetry heart rate monitoring system (optional)
Telemetry heart rate monitoring chest strap (optional)
Intensity levels:
Pedal size
20
4.5 inches / 11.5 centimeters
Poly-V belt-drive
None; bike is self-powered
Optional
Drive type:
Power requirements:
Accessory Tray:
Color:
Commercial gray
ASSEMBLED DIMENSIONS:
Length
56.5 inches / 143.5 centimeters
25.7 inches / 65.4 centimeters
54 inches / 137 centimeters
142 pounds / 64.4 kilograms
Width
Height
Weight
SHIPPING DIMENSIONS:
Length
59.84 inches / 152 centimeters
17.91 inches / 45.5 centimeters
29.92 inches / 76 centimeters
167 pounds / 75.6 kilograms
Width
Height
Weight
27
Download from Www.Somanuals.com. All Manuals Search And Download.
|