41
64
0
Up
Down
On/Off
SuperFrost
Alarm
On/Off
Light
Zone
Up
Down
Installation
Instructions
For wine cooler with
NoFrost freezer compartment and
Side-By-Side Units
with IceMaker
Instructions
de montage
Armoire de mise en température des
vins avec congélateur NoFrost et les
appareils côte à côte
avec IceMaker
2
-
-
6
4
8
6
-12
4
Instrucciones
de instalación
2
4
6
-
-
6
8
-12
3
Armario de acondicionamiento de
vinos con congelador NoFrost y
unidades lado a lado
2
4
6
-
-
6
8
-12
2
con IceMaker
2
4
6
-
-
6
8
-12
1
WFI1051 / EWTN/ 2956
7082 408-00
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT
TO THE INSTALLER
It is very important that the guidelines and
instructions are followed in the manual to ensure
proper installation and operation of the unit. The
Installation Guidelines section contains important
information for making sure the installation is cor-
rect. Read and understand all the information in
Installation Guidelines, and in this manual before
the unit is installed.
A delight in freshness
WFI1051 / EWTN 2956
1
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Contents
Page
Installation Guidelines................................................................................. 3
Area Requirements............................................................................... 3
Electrical Requirement.......................................................................... 3
Customer’s Responsibility .................................................................... 3
Blocking For Safety............................................................................... 3
Unit Venting........................................................................................... 3
Planning Information................................................................................... 4
Cabinet Opening Dimensions............................................................... 4
Assembling Decorative Panels................................................................... 7
Integrating Cabinetry................................................................................... 8
Framed Panels...................................................................................... 8
Overlay Panels...................................................................................... 9
Reversing Door Hinges............................................................................. 14
Door Opening Angle........................................................................... 17
Installation................................................................................................. 18
Blocking For Safety................................................................................... 22
IceMaker.................................................................................................... 23
Water Connection ............................................................................... 23
Connection to the Water Supply......................................................... 24
Side-By-Side Installation........................................................................... 25
A delight in freshness
WFI1051 / EWTN 2956
2
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION GUIDELINES
Area Requirements
Verify the following:
WARNING
!
ELECTROCUTION HAZARD
• Floors can support refrigerator’s weight plus
approximately 1200 pounds (544 kg) of food
weight.
Electrical Grounding Required. This appli-
ance is equipped with a three-prong
(grounding) polarized plug for your protec-
tion against possible shock hazards.
• Finished kitchen floor height has to be level.
Appliance must be shimmed to the floor level if
the floor heights are not equal to make sure air
vents are not obstructed.
DO NOT remove the round grounding
prong from the plug.
DO NOT use a two-prong grounding
adapter.
DO NOT use an extension cord to
connect power to the unit.
•
•
•
• Remove anything attached to rear or side walls
that can obstruct refrigerator opening.
• Cutout dimensions are accurate.
Customer’s Responsibility
A 115 Volt, 60 Hz, 15 Amp (20 Amp for side-by-
side installation) fused electrical supply is required.
We recommend using a dedicated circuit for this
appliance to prevent electrical overload. Follow the
National Electrical Code and local codes and ordi-
nances when installing the receptacle.
• Electrical outlet is in correct location.
Do not install this unit next to any other refrigerator
or freezer except another Liebherr model. Liebherr
models are designed to allow side-by-side instal-
lation. They are equipped with a heating system
to eliminate condensation when units are installed
side by side. Installing this unit next to any other
refrigerator or freezer can cause condensation or
cause damage to the Liebherr unit.
Blocking For Safety
The anti-tip brackets must be installed to prevent
the unit from tipping after it is installed. Refer to
Blocking For Safety.
Electrical Requirement
Unit Venting
If codes require a separate grounding circuit to be
used, have a qualified electrician install the circuit.
DO NOT restrict the air flow. Air flow must be pro-
vided for the unit to operate. The factory air vents
provide 31 square inches (200 cm²) of air flow per
unit. If you are replacing the factory air vents with
an overlay, the air flow must be the same or greater
than the factory air vents.
WARNING
!
Do not ground to a gas pipe. Check with
a qualified electrician if you are not sure
the appliance is properly grounded. Do not
have a fuse in the neutral or grounding
circuit.
WARNING
!
ELECTRICAL SHOCK HAZARD
• Electrically ground refrigerator.
• Do not use an extension cord.
• Failure to follow these instructions
could result in fire or electrical shock.
A delight in freshness
WFI1051 / EWTN 2956
3
Download from Www.Somanuals.com. All Manuals Search And Download.
PLANNING INFORMATION
Cabinet Opening Dimensions - Figure 1
Allow units to open a minimum of 90° to prevent
problems removing drawers. With the door open-
ing 90°, you may have to move drawers slightly to
clear the door interior.
Refer to the minimum door clearances in the Pre-
Installation Specifications chart.
• Allow for a minimum 3-3/4" (95 mm) filler, for
corner installations, so the door can open to 90°.
If you’re using raised panels, consider using a
wider filler.
IMPORTANT
Refer to the full scale illustrations at the end of
this section for specifics on door openings and
filler size alternatives.
3"
"
(76mm)
"
"
Figure 1
A delight in freshness
WFI1051 / EWTN 2956
4
Download from Www.Somanuals.com. All Manuals Search And Download.
PLANNING INFORMATION
WFI 1051 - Figure 2
Figure 2
A delight in freshness
WFI1051 / EWTN 2956
5
Download from Www.Somanuals.com. All Manuals Search And Download.
PLANNING INFORMATION
Side-By-Side WFI 1051 - RBI 1400 - Figure 3
A delight in freshness
WFI1051 / EWTN 2956
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLING DECORATIVE PANELS
Figure 4
Proceed as shown in the illustration:
(1) Door change frames
(2) Decorative panel
(3) Screws for door change frames
(4) Handle, depending on model
(5) M4 x 10 screws for handle
(6) Filler strip
Figure 4
A delight in freshness
WFI1051 / EWTN 2956
7
Download from Www.Somanuals.com. All Manuals Search And Download.
INTEGRATING CABINETRY
IMPORTANT
Framed Panels - Figure 5
If you are replacing the factory air vents with
an overlay, DO NOT restrict the air flow. The air
flow must be the same or greater than the fac-
tory air vents of 31 square inches (200 cm²).
If the thickness of the custom panels is less than
1/4" (6.4 mm), they must be backed up with a sheet
of shim material to build the total thickness to 1/4"
(6.4 mm). If the panel is thicker than 1/4" (6.4 mm),
an edge must be routed around the panel to
ensure a proper fit.
The door handles must be installed before the
screw covers are installed. If you fail to install
the handles before the screw covers, you can
damage the covers. The screw covers are
taped to the unit doors during shipping. Use
care when removing covers.
The door panel weight must not exceed
25 lb (11,3 kg).
1/4"
(6.4 mm)
22-9/16" (573 mm)
max. 17-1/2" (445 mm)
1/4" (6.4 mm)
Window cutout
=
=
1/4"
(6.4 mm)
1/4" (6.4 mm)
Figure 5
A delight in freshness
WFI1051 / EWTN 2956
8
Download from Www.Somanuals.com. All Manuals Search And Download.
INTEGRATING CABINETRY
with three panels, the decorative overlay panel, a
3/32" (2.5 mm) spacer panel and a 1/4" (6.4 mm)
backer panel.
Depending on your cabinet manufacturer, this could
be one panel routed for different dimensions or,
more likely, three different panels.
W
Overlay Panels - single install - Figure 6
The overlay design line allows decorative panels to
cover the door trim for a more seamless appear-
ance that blends with the design of the room. To
achieve this look, the most common way is to work
=
1 Overlay Panel
2 Spacer Panel
3 Backer Panel
Approx. 3/4"
(19.1mm)
3/32" (2.5mm)
1/4" (6.4mm)
=
=
=
Window cutout
=
W
H - Winecooler H - Freezer
23-5/16"
(592 mm)
1 Overlay
Panel
33-5/8"
(854 mm)
38"
(965 mm)
36-1/4"
(921 mm)
31-1/2"
(800 mm)
21-3/4"
(553 mm)
2 Spacer
Panel
=
=
32-37/64"
(828 mm)
37-9/32"
(947 mm)
3 Backer 22-3/4"
(576 mm)
Panel
max 25-1/2"
(648 mm)
max17-1/2"
(445 mm)
Window
cutout
IMPORTANT
If you are replacing the factory air vents with an
overlay, DO NOT restrict the air flow. The air flow
must be the same or greater than the factory air
vents of 31 square inches (200 cm²).
=
=
The door handles must be installed on the
overlay panels before the screw covers are
installed. If you fail to install the handles on
the overlay panels before the screw covers ,
you can damage the covers. The screw covers
are taped to the unit doors during shipping.
Use care when removing covers.
The door panel weight must not exceed
25 lb (11,3 kg).
=
Figure 6
=
=
A delight in freshness
WFI1051 / EWTN 2956
9
Download from Www.Somanuals.com. All Manuals Search And Download.
INTEGRATING CABINETRY
with three panels, the decorative overlay panel, a
3/32" (2.5 mm) spacer panel and a 1/4" (6.4 mm)
backer panel.
Depending on your cabinet manufacturer, this could
be one panel routed for different dimensions or,
more likely, three different panels.
W
Overlay Panels - side by side install
The overlay design line allows decorative panels to
cover the door trim for a more seamless appear-
ance that blends with the design of the room. To
achieve this look, the most common way is to work
=
1 Overlay Panel
2 Spacer Panel
3 Backer Panel
Approx. 3/4"
(19.1mm)
3/32" (2.5mm)
1/4" (6.4mm)
=
=
=
Window cutout
=
W
H - Winecooler H - Freezer
23-5/16"
(592 mm)
1 Overlay
Panel
33-5/8"
(854 mm)
38"
(965 mm)
36-1/4"
(921 mm)
31-1/2"
(800 mm)
21-3/4"
(553 mm)
2 Spacer
Panel
=
=
32-37/64"
(828 mm)
37-9/32"
(947 mm)
3 Backer 22-3/4"
(578 mm)
Panel
max 25-1/2"
(648 mm)
max17-1/2"
(445 mm)
Window
cutout
IMPORTANT
If you are replacing the factory air vents with an
overlay, DO NOT restrict the air flow. The air flow
must be the same or greater than the factory air
vents of 31 square inches (200 cm²).
=
=
The door handles must be installed on the
overlay panels before the screw covers are
installed. If you fail to install the handles on
the overlay panels before the screw covers ,
you can damage the covers. The screw covers
are taped to the unit doors during shipping.
Use care when removing covers.
The door panel weight must not exceed
25 lb (11,3 kg).
=
3/16"
(4.7mm)
A delight in freshness
WFI1051 / EWTN 2956
10
Download from Www.Somanuals.com. All Manuals Search And Download.
INTEGRATING CABINETRY
A
Figure 7
C
The factory setting for the door to swing open is
130°. Use this illustration to ensure other cabi-
nets or counters do not interfere with the door
opening.
Frameless cabinets: The casing trim overlaps
the cabinets at the side and top. Cabinets may
require filler strips to prevent interference with
the cabinet door swing. The door opening must
allow for filler strips.
1"
(25.4 mm)
2"
3"
(50.8 mm )
(76.2 mm)
3/4"
(19.1 mm)
1/2"
(12.7 mm)
1/4"
1-3/4"
(44.5 mm)
2-3/4"
(69.9 mm)
2-1/2"
(63.5 mm)
2-1/4"
(57.2 mm)
1-1/2"
(38.1 mm)
1-1/4"
(31.8 mm)
(6.4 mm)
1/4"
(6.4 mm)
1/2"
(12.7 mm)
3/4"
(19.1 mm)
1"
(25.4 mm)
3/32"
(2.4 mm)
D
1"
3/4"
1/2"
1/4"
(25.4 mm) (19.1 mm) (12.7 mm) (6.4 mm)
Figure 7
A delight in freshness
WFI1051 / EWTN 2956
11
Download from Www.Somanuals.com. All Manuals Search And Download.
INTEGRATING CABINETRY
Figure 8
The optional setting for the door to swing open is
90°. Use this illustration to ensure other cabinets or
counters do not interfere with the door opening.
Frameless cabinets: The casing trim overlaps the
cabinets at the side and top. Cabinets may require
filler strips to prevent interference with the cabinet
door swing. The door opening must allow for filler
strips.
A delight in freshness
WFI1051 / EWTN 2956
12
Download from Www.Somanuals.com. All Manuals Search And Download.
INTEGRATING CABINETRY
A
C
1"
3"
2"
(50.8 mm )
1-3/4"
(44.5 mm)
1-1/2"
(38.1 mm)
1-1/4"
(31.8 mm)
(25.4 mm)
3/4"
(76.2 mm)
(19.1 mm)
2-3/4"
(69.9 mm)
2-1/2"
(63.5 mm)
2-1/4"
1/2"
(12.7 mm)
1/4"
(6.4 mm)
(57.2 mm)
1/4"
(6.4 mm)
1/2"
(12.7 mm)
3/4"
(19.1 mm)
1"
24”
(609.6 mm)
(25.4 mm)
3/32”
(2.4 mm)
1-1/4"
(31.8 mm)
1-1/2"
48”
(1219.2 mm)
(38.1 mm)
D
1/4"
(6.4 mm)
1/2"
(12.7 mm)
3/4"
(19.1 mm)
1"
(25.4 mm)
Figure 8
A delight in freshness
WFI1051 / EWTN 2956
13
Download from Www.Somanuals.com. All Manuals Search And Download.
REVERSING DOOR HINGES
The door hinges can be changed from one side to
the other if required.
1. Figure 10: Top: Unscrew the hinge pin (2) and
remove the screw (5) with the eccentric.
2. Swivel out the door at the top, ensuring that
you do not lose the stop (7) and bushing (8); lift
off the door and place it on the floor.
8
3. Center: Pull out the hinge pin (9) with its washer.
4. Swivel out the lower door, lift it out and place it
on the floor. Take care not to lose the stop (7)
and washers (8).
8
5. Unscrew all the door fittings (14, 15, 16, 17).
6. Figure 11: Unscrew all the door change frames
and exchange them with one another (6 with 8,
4 with 7 and handle - remove cover 1). Secure
them in position using the same screws.
7. Ensure that the door change frames are cor-
rectly positioned and mitered.
Figure 10
WARNING
!
Make sure the corners of the door change
frames are positioned correctly. Sharp
edges will be exposed if they are not
mitered or positioned correctly.
Figure 11
A delight in freshness
WFI1051 / EWTN 2956
14
Download from Www.Somanuals.com. All Manuals Search And Download.
REVERSING DOOR HINGES
8. Figure 12: Unscrew the lower hinge (13).
10. Unscrew the center hinge (10) and cover (11),
pull them off to the side and after turning
them 180°, slide them on again on the opposite
side and secure them.
- Remove the stop and bushings (7, 8).
- Transfer hinge pin (2) to the opposite side.
- Turn the stop (7) 180° and position bush-
ings (8) as shown in the detailed drawing.
- Screw on hinge (13) on the new hinge side.
11. Place the lower door on the hinge pin (2) at the
bottom.
9. On the lower door: Reinstall the door fittings
(14, 15). Pay special attention to the part (14)
with the stop.
- Swivel in the door.
- Pay special attention to the bushing (12) in the
center hinge (10).
- Insert hinge pin (9) and add the washer.
Figure 12
A delight in freshness
WFI1051 / EWTN 2956
15
Download from Www.Somanuals.com. All Manuals Search And Download.
REVERSING DOOR HINGES
12. Figure 13: Lift up cover (3) on handle side,
push outward; lift up cover (1) on hinge side
and pull off.
13. Unscrew mounting plate (21): first mounting
screw (20), then inner retaining screw (25).
- Unscrew hinge (4): first remove the mount-
ing screw (20), then retaining screws (25). Fit
hinge (4) to opposite side: for easy assem-
bly, fit hinge from above and first tighten
with the upper retaining screw (25) M5, then
14. Remove the eccentric (5) with the retaining
screw in the hinge (4).
15. On the upper door: Reinstall the door fittings
(16, 17). Pay special attention to the fitting (17)
with the stop.
16. Place the upper door on the center hinge, fit the
bushing (8), stop (7) and washer on the door,
swivel in the door at the top and insert and
secure the hinge pin (2) from above through the
hinge and stop.
screw (25) and finally mounting screw M4 (20). 17. Re-insert the eccentric (5) with the retaining
- Turn mounting plate (21) 180° and screw tight
again on the new handle side: first retaining
screw (25), then mounting screw (20).
screw as shown in the detailed drawing.
Check for proper alignment of all doors. Adjust
them if necessary using the slots on the hinge.
21
4
20 25
20
25
21
4
12
14
15
17
16
15
Figure 13
A delight in freshness
WFI1051 / EWTN 2956
16
Download from Www.Somanuals.com. All Manuals Search And Download.
REVERSING DOOR HINGES
Door Opening Angle - Figures 14, 15
The appliance is delivered with a door opening
angle of 130°.
If the angle is to be decreased to 90°, proceed as
follows:
• Insert attached screw (6) in the upper hinge as
shown in Figure 14.
• Insert attached screw (6) in the lower hinge as
shown in Figure 15.
Figure 14
Figure 15
A delight in freshness
WFI1051 / EWTN 2956
17
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Only install the winecooler/freezer in a stable kitch-
en cabinet that has been properly aligned.
- Mount and fix the handles, depending on your
model and choice.
Unpacking
Unpack the installation kit and check with the pro-
vided parts list if all parts are included.
The part numbers given in the parts list are identical
to the numbers in the respective figures.
For installation you will need the following tools:
Included:
- Star Key Torx® 15
- Star Key Torx® 20
- Star Key Torx® 25
- Socket Wrench 8 mm
- Open-end Wrench 10 mm
Not in package:
- Phillips (star) screwdriver
- Level
- Ruler
Figure 16: Installation with Ventilation Grille Set:
1. Screw the installation frame at the top (1) onto
the appliance with screws (2).
2. Place the ventilation grille (3) on this, align it in
the center and secure at the front from under-
neath.
3. Slide brackets (4) onto the side installation
frames (5) from above and below.
4. Using the frame (5), screw the brackets onto
the side wall*.
5. Slide the side installation frames (5) upwards
until they are in contact with the underside of
the ventilation grille.
6. Secure the side frames with the adhesive sec-
tion (7) to prevent them from sliding down.
Remove the protective film and affix the adhe-
sive sections over the upper brackets on the
handle and hinge sides.
Figure 16
* Depending on model and options
A delight in freshness
18
WFI1051 / EWTN 2956
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
- Figure 17: Connect the appliance to the
main power supply.
- If the appliance is equipped with an
IceMaker, establish the connection for
the water supply. See “IceMaker, Water
Connection”.
1. Carefully slide the appliance into the cabinet
until the ventilation grille touches the surround-
ing kitchen cabinet.
2. Align the appliance until it is parallel with the
surrounding kitchen cabinet. Use the open-
end wrench 10 mm (3) to adjust the feet at the
front. Turn clockwise for up and counterclock-
wise for down. For the rear use the adjusting
1
2
1
2
3
2
3
8 spanner
2
3
10 spanner
Figure 17
bolt (2). Turn clockwise for down and counter-
clockwise for up.
Maximum adjustment: 19/64" (15 mm).
3. Figure 18: Align the appliance at the side with the
cabinet side panel and attach it with screws (1).
- Cover the screws with cover caps (2).
4. Fit the ventilation grille at the bottom [(3) if the
door is hinged on the left, (4) if it is on the right]:
Secure the ventilation grille so that it touches
the floor and then adjust it using the slots.
Figure 18
A delight in freshness
WFI1051 / EWTN 2956
19
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
At least 31 square inches (200cm2)
The following ventilation cross-section
and distances must be observed:
- There must be a ventilation space of
at least 31 square inches (200 cm²)
per appliance in the cabinet plinth
and under the cabinet top panel.
- The depth of the ventilation duct at
the rear of the cabinet must be at
least 1-1/2" (38 mm).
1
Alternatively:
1. For built-in appliances without ven-
tilation grilles and only with an instal-
lation frame, ventilation must take place
through the ventilation duct at the rear
of the cabinet.
2
1
Built-in appliances with an installation
frame:
•
Figure 19:
- Screw the complete installation
frame (2) to the appliance.
Figure 19
2. Built-in appliances with a wooden
ventilation grille:
Figure 20: Cut out the wooden trim
for use as a ventilation grille using the
enclosed template.
- The required ventilation cross-sec-
tion must be at least 31 square
inches (200 cm²) when a single
appliance is installed, which cor-
responds to template “small” (If you
install two appliances side-by-side,
the cross-section must be at least
62 square inches, (400 cm²), which
corresponds to template “double-
size;” for more information see “Side-
by-Side Installation”).
Remove the attachment bracket (2)
from the installation frame and screw it
to the appliance (1) from underneath.
Place the wooden ventilation grille (5)
on the appliance, align it in the center
and secure it from the rear using the
attachment bracket (2).
2
1/2"
5
(13 mm)
•
1
24"
(609,6 mm)
3-11/16"
(93,7 mm)
Figure 20
A delight in freshness
WFI1051 / EWTN 2956
20
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
A delight in freshness
WFI1051 / EWTN 2956
21
Download from Www.Somanuals.com. All Manuals Search And Download.
BLOCKING FOR SAFETY
Figure 21: Secure the appliance in place so it does
IMPORTANT
not tip forward when the fully stocked door is
opened.
The anti-tip brackets can be installed in either
direction or closer together. Always position
the anti-tip brackets as wide apart as pos-
sible, but make sure they are anchored to two
studs.
2. Measure the distance from the floor to the
upper edge of the unit.
3. Locate and mark two wall studs (1) against the
wall where the refrigerator will be located. The
space between the unit top and the bottom of
the brackets must not be more than
1/4" (6.4 mm).
6. Using the adjustable roller base, raise the unit
until it makes contact with the brackets. Make
sure the front levelers are firmly on the floor to
prevent appliance from tipping forward.
4. Make sure the screws (2) extend a minimum of
IMPORTANT
1" (25.4 mm) into each of the wall studs.
If your unit is positioned in between the
wall studs, a board can be secured to the
wall. Make sure the board is secured to the
studs with screws that will penetrate into the
studs a minimum of 1" (25.4 mm). The board
should be a minimum of 1" x 6" (25.4 mm x
152.4 mm) and long enough to secure both
ends to the wall studs.
5. Make sure the anti-tip brackets (3) extend
at least 3" (76.2 mm) over the unit and are
securely in place.
3
1
2
min 3"
Figure 21
A delight in freshness
WFI1051 / EWTN 2956
22
Download from Www.Somanuals.com. All Manuals Search And Download.
ICEMAKER
Water Connection - Figure 22
Please read the first three points of the safety
instructions and warnings before connecting the
appliance to the main water supply.
• The water pressure must be between 21.8-
87.0 psi (1.5-6 bar).
• Use a 1/4" OD copper line to connect the water
supply to the solenoid valve. This is not sup-
plied with the appliance (Figure 22).
• A shut-off valve, such as the saddle valve illus-
tration here, must be installed between the hose
line and the main water supply so the water sup-
ply can be stopped if necessary.
Figure 22
Do not install the shut-off valve behind the
appliance.
• If you have hard water, we recommend you install
a water softener. Also, a filter must be installed if
the water contains solids such as sand.
• All equipment and devices used to supply the
water to the appliance must comply with the cur-
rent regulations for your geographical area.
A delight in freshness
23
WFI1051 / EWTN 2956
Download from Www.Somanuals.com. All Manuals Search And Download.
ICEMAKER
3. Open the shut-off valve for the water supply
and check the entire water system for leaks.
Before the appliance is used for the first time a
licensed plumber should bleed air from the sys-
tem.
Connection to the Water Supply
1. Install the shut-off valve, water filter and auto-
matic shut-off device as required.
Note
The solenoid valve is located at the rear of
your unit.
4. Insert the electrical plug for the combined appli-
ance into the electrical outlet (Figure 23).
2. Place a 1/4" OD copper tubing between the
shut-off valve and solenoid valve. Make sure
there is approximately 30" (70 cm) of excess
tubing behind the unit for easy connection.
5. Move the appliance into final position in the
room.
IMPORTANT
The solenoid valve has a Metric R3/4 male
connection.
A R3/4(metric) to a 1/4" OD adapter and
cable clip are supplied with the icemaker.
Figure 24: Remove the cover cap (4) from
the solenoid valve (1). Install the connection
bracket (2) with sealing ring (6) on the solenoid
valve (1). Attach the copper tube to the connec-
tion bracket (2). Secure the copper tube (3) to
the appliance using the cable clip (5).
Figure 23
A delight in freshness
24
WFI1051 / EWTN 2956
Download from Www.Somanuals.com. All Manuals Search And Download.
SIDE-BY-SIDE INSTALLATION
1
4
1
6
2
3
5
5
Figure 24
A delight in freshness
WFI1051 / EWTN 2956
25
Download from Www.Somanuals.com. All Manuals Search And Download.
SIDE-BY-SIDE INSTALLATION
Unpacking
Figure 25: To install the WFI 1051 appliances side-
by-side, proceed as follows:
Unpack the side by side installation kit and check
with the provided parts list if all parts are included.
The part numbers given in the parts list are identical
to the numbers in the respective figures.
- Always place the WF/WFI 1051 with the hinges
on the left-hand side (looking from the front).
Installation with SBS Ventilation Grille Set:
For installation you will need the following tools:
1. Affix the spacer (1) on the side wall of the appli-
ance – remove the protective film.
Included:
- Star Key Torx® 15
- Star Key Torx® 20
- Star Key Torx® 25
- Socket Wrench 8 mm
- Open-end Wrench 10 mm
2. Push the appliances together,
- align them parallel to each other.
3. Use a level on the top to align them to the
same height:
4. Use the open-end wrench 10 mm (3) to adjust
the feet at the front of the roller base. Turn
clockwise for up and counterclockwise for down.
For the rear, turn the adjusting bolt (2) clock-
wise down and counterclockwise up.
Not in package:
- Phillips (star) screwdriver
- Level
- Ruler
4
Figure 25
A delight in freshness
WFI1051 / EWTN 2956
26
Download from Www.Somanuals.com. All Manuals Search And Download.
SIDE-BY-SIDE INSTALLATION
5. Figure 26: Secure the installation frame (3)
5
2
3
at the top to the appliances with screws (2).
- Align the appliance at the front bottom.
- Use the predrilled holes to align the
installation frame (2).
- First mount the installation (3) frame with
4 screws (2) to one appliance, then align
the other appliance with the predrilled
holes to the installation frame (3) and
secure it with the screws (2).
6. Figure 26: Position the attachment brack-
ets (6) at the rear of the appliances at the
top and bottom. Slide the upper attachment
bracket upwards as far as possible. Secure it
at the side using the screws provided (5). Do
not overtighten!
6
6
5
6
5
6
81-/4"
c.a(210)
Figure 26
A delight in freshness
27
WFI1051 / EWTN 2956
Download from Www.Somanuals.com. All Manuals Search And Download.
SIDE-BY-SIDE INSTALLATION
7. Figure 27: Push the long carriage bolt
M5x260 (7) through the leveling wheels as shown.
Fit in a washer (8). Screw on the wing nut (9) and
tighten it manually. Do not overtighten.
8. Turn the adjustable roller base up. Otherwise
you will damage the floor when you push in the
appliances.
9. Secure the ventilation grille (10) to the appli-
ance with screws (11). Push in the sealing
strip (4) as shown.
10
9
4
11
9
8
7
7
7
8
8 spanner
2
4
3
10 spanner
Figure 27
A delight in freshness
WFI1051 / EWTN 2956
28
Download from Www.Somanuals.com. All Manuals Search And Download.
SIDE-BY-SIDE INSTALLATION
10. Figures 28, 29: Slide the side installation
10
frames (15) upward until they are in con-
tact with the underside of the ventilation
grille, Figure 28.
11. Secure the side frames with the adhe-
sive section (17) to prevent them from
sliding down. Remove the protective film
and place the adhesive sections over the
upper brackets.
17
11
12. Install anti-tip brackets for each appliance.
Refer to “Blocking For Safety.”
17
15
15
11
17
Figure 28
min 3"
Figure 29
A delight in freshness
WFI1051 / EWTN 2956
29
Download from Www.Somanuals.com. All Manuals Search And Download.
SIDE-BY-SIDE INSTALLATION
13. Figure 30, 31: Connect the appliances:
- to the main power supply and
- to the water supply if the appliance is equipped
with an IceMaker. See “IceMaker, Water
Connection,” Figure 30.
14. Carefully slide the connected appliances into the
recess until the ventilation grille touches the top,
Figure 31.
15. Align the appliances by using only the outer lev-
13
eling wheels at the front (3) and rear (2).
Figure 30
8 spanner
14
2
3
10 spanner
15
Figure 31
A delight in freshness
WFI1051 / EWTN 2956
30
Download from Www.Somanuals.com. All Manuals Search And Download.
SIDE-BY-SIDE INSTALLATION
16. Figure 32: Attach the aligned combination
to the surrounding kitchen cabinet. Secure it
through the side frames using the screws (20)
provided.
-
Cover the screws with cover caps (21).
17. Now adjust the center adjustable roller
bases (22) so that they make slight contact
with the floor.
18. Install the lower ventilation grille (23): Secure
the ventilation grille so that it touches the floor
and adjust it using the slots. Do not overtighten!
20
21
16
8 spanner
2
3
10 spanner
17
22
18
24
24
24
23
24
Figure 32
A delight in freshness
WFI1051 / EWTN 2956
31
Download from Www.Somanuals.com. All Manuals Search And Download.
SIDE-BY-SIDE INSTALLATION
1. For built-in appliances without ventilation
grilles and only with installation frame (2), ven-
tilation must take place through the ventilation
duct at the rear of the cabinet. Ensure that the
ventilation cross-section is at least 31 square
inches (200 cm²) per appliance.
At least 62 square inches (400 cm²) for side-by-
side installation of two appliances. Built-in appli-
ances with an installation frame:
- Figure 33: Screw the installation frame (2) to
the appliance through the attachment brack-
ets.
At least 31 square inches (200cm2)per unit
1
2
Figure 33
A delight in freshness
WFI1051 / EWTN 2956
32
Download from Www.Somanuals.com. All Manuals Search And Download.
SIDE-BY-SIDE INSTALLATION
Built-in appliances with a wooden ventilation
- Remove the attachment brackets from the
installation frame (2) and screw them to the
appliance from underneath.
- Place the wooden ventilation grille (5) on the
appliance, align it in the center and secure it
from the rear using the attachment brackets.
grille:
2. Figure 34: Cut out the wooden trim for use as
a ventilation grille using the attached template.
- The required ventilation cross-section must
be at least 62 square inches (400 cm²) for
side-by-side installation of two appliances,
which corresponds to the attached template
“double-size.”
2
1/2"
(13 mm)
5
48"
(1219,2 mm)
3-11/16"
(93,7 mm)
Figure 34
A delight in freshness
WFI1051 / EWTN 2956
33
Download from Www.Somanuals.com. All Manuals Search And Download.
|