Lennox Hearth Stove SS210 User Manual
INSTALLATION AND OPERATION MANUAL  
Free-Standing  
EPA Certified  
Wood-Burning Stoves  
Save These Instructions  
For Future Reference  
Performer ST210  
and SWS210  
P/N 775215M, Rev. F, 09/2011  
Performer SS210  
Wood Stoves  
Models Performer™ SS210,  
ST210 and SWS210  
A French manual is available upon request. Order P/N 775215CF.  
Ce manuel d’installation est disponible en francais, simplement en faire la demande. Numéro de la  
pièce 775215CF.  
This appliance must be properly installed and operated in order to prevent the pos-  
sibility of a house fire. Please read this entire installation and operation manual  
beforeinstallingandusingyourwoodstove.Failuretofollowtheseinstructions  
could result in property damage, bodily injury or even death. Contact your  
local building or fire officials to obtain a permit and information on any  
installationrequirementsandinspectionrequirementsinyourarea.  
Portland  
US  
Report # 050-S-03b-2  
WARNINGS  
• Hot! Do not touch! The glass and surfaces of this appliance will  
be hot during operation and will retain heat for a while after  
shutting off the appliance. Severe burns may result.  
• Carefully supervise children in the same room as appliance.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ing season to check for soot and creosote accumulations.  
Any accumulations over 1/8” thick should be removed by  
a professional chimney sweep. Do not attempt to burn out  
heavy creosote accumulations with a hot fire. If large ac-  
cumulationsareoccurring,reviewyourburningprocedures.  
14. Ifacreosotefireshoulddevelop,thefiredepartmentshould  
be called immediately and then attempts should be made  
to control the fire until assistance arrives. If a “runaway”  
fire should develop causing over-heating of the stove, the  
door and draft regulators should be closed immediately.  
The fire should die down once deprived of oxygen. After a  
severe chimney fire, the complete chimney system should  
be checked before further use.  
IMPORTANT SAFETY AND WARNIING  
INFORMATION  
READ THIS MANUAL IN ITS ENTIRETY AND UNDER-  
STAND THESE RULES TO FOLLOW FOR SAFETY.  
1. When this room heater is not properly installed, a house  
fire may result. To reduce the risk of fire, follow the instal-  
lation instructions. Contact local building or fire officials  
aboutrestrictionsandinstallationinspectionrequirements  
in your area.  
2. Wear gloves during installation to avoid injury from sharp  
edges on the stove and/or its parts.  
3. This unit is designed and engineered to burn only dry, well-  
seasoned wood. Burning wet wood will greatly reduce the  
stove’s efficiency, produce excessive amounts of smoke  
and can cause dangerous chimney fires due to creosote  
build-up.  
4. Beforeopeningthedoor,thedraftcontrolmustbefullyopen  
to avoid possible combustion flash (ignition of hot volatile  
gases as the door is opened).  
5. Never use gasoline, gasoline-type lantern fuel, kerosene,  
charcoallighterfluid,orsimilarliquidstostartor’freshenup’  
a fire in this heater. Keep all such liquids well away from  
the heater while it is in use. DO NOT USE CHEMICALS OR  
FLUIDS TO START THE FIRE.  
6. Whileburning, fuelutilizesoxygenfromtheairintheroom.  
Be sure to allow an adequate amount of fresh air into the  
room where the stove is burning.  
7. The outside surface of the stove will be hot while burning  
properly and can set items like clothing and curtains on  
fire. Keep furnishings and other combustible materials  
away from the stove. Using the heat from the stove to dry  
wet clothing can be hazardous if clothes are placed too  
near the surface of the stove.  
15. Do Not Use Grate Or Elevate Fire - Build Wood Fire Directly  
On Hearth (firebrick). Do not use andirons or other methods  
of supporting the fuel.  
16. Please read this entire manual before you install and use  
your new room heater. Failure to follow instructions may  
result in property damage, bodily injury, or even death.  
17. Checkalllocalbuildingandsafetycodesbeforeinstallation.  
The installation instructions and appropriate code require-  
ments must be followed exactly and without compromise.  
In the absence of local codes the following standards and  
codes must be followed.  
18. In the U.S.A, install in accordance with the National Fire  
Protection Association’s Code, NFPA 211, Standards for  
Chimneys,Fireplaces,VentsandSolid-Fuel-BurningAppli-  
ances, or similar regulations, may apply to the installation  
of a Solid-Fuel-Burning appliance in your area. In Canada,  
the guideline is established by the CSA Standard, CAN/  
CSA-B365-M93, Installation Code for Solid-Fuel-Burning  
Appliances and Equipment.  
19. DO NOT CONNECT TO OR USE IN CONJUNCTION WITH ANY  
AIR DISTRIBUTION DUCTWORK UNLESS SPECIFICALLY  
APPROVED FOR SUCH INSTALLATIONS.  
20. WARNING: BURNING IMPROPER FUEL (I.E. CHARCOAL)  
CAN RESULT IN CARBON MONOXIDE POISONING, WHICH  
MAY LEAD TO DEATH!  
21. CarbonMonoxidePoisoning–Earlysignsofcarbonmonox-  
ide poisoning resemble the flu with headaches, dizziness,  
or nausea. If you have these signs, get fresh air at once!  
Havetheheaterinspectedbyaqualifiedservicetechnician.  
Some people are more affected by carbon monoxide than  
others. These include pregnant women, people with heart  
or lung disease or anemia, those under the influence of  
alcohol, and those at high altitudes.  
22. Failure to use manufacturer provided parts, variations in  
techniquesandconstructionmaterialsorpracticesotherthan  
those described in this manual may create a fire hazard and  
void the limited warranty.  
8. HOT WHILE IN OPERATION. KEEP CHILDREN, CLOTHING  
FURNISHINGSANDCOMBUSTIBLEMATERIALACONSIDER-  
ABLEDISTANCEAWAY. CONTACTMAYCAUSESKINBURNS.  
Do not allow children to play near the stove without close  
supervision. Do not touch the stove while it is burning.  
Use extreme caution while the unit is in use. Surface tem-  
peratures become dangerously hot and can cause serious  
burns.  
9. Donotallowanyonetooperatethestovewhoisnotfamiliar  
with the operating instructions.  
10. Attempts to achieve heat output rates that exceed stove  
design specifications can result in permanent damage to  
the stove. Never leave your stove unattended on high burn  
rates. This may cause overfiring. Overfiring the stove may  
cause a house fire. If the stove glows, you are overfiring.  
11. Keep a water hose or hand-operated fire extinguisher close  
for safety.  
23. Do not make any make-shift compromises during installa-  
tion. Any modification or alteration may result in damage  
to the appliance or dwelling and will void the warranty,  
certification and listings of this unit.  
12. Smoke Detectors - Since there are always several poten-  
tial sources of fire in any home, we recommend installing  
smoke detectors. If possible, install the smoke detector in  
a hallway adjacent to the room (to reduce the possibility  
of occasional false activation from the heat produced by  
the stove). If your local code requires a smoke detector  
be installed within the same room, you must follow the  
requirements of your local code. Check with your local  
building department for requirements in your area.  
13. Inspectyourchimneyatleastonceamonthduringtheburn-  
24. These appliances are designed as supplemental heaters.  
Therefore, it is advisable to have an alternate heat source  
when installed in a dwelling.  
25. Do Not Overfire – If Heater or Chimney Connector Glows,  
You Are Overfiring.  
26. DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERV-  
ING ANOTHER APPLIANCE.  
27. DO NOT BURN GARBAGE OR FLAMMABLE FLUIDS SUCH  
AS GASOLINE, NAPHTHA OR ENGINE OIL.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
performance problems as well as be a safety hazard. A draft test should  
read greater than .04’ W.C. (inches water column) and less than .08”  
W.C. As per NFPA-211 standard (see paragraph below), the installer  
must take into account all variables within the installation and install the  
appliance in such a manner that satisfies the draft requirements of the  
appliance. See Chimney Guidelines below to assist you in selecting the  
proper venting system for your installation.  
TESTING INFORMATION  
Thismanualdescribestheinstallationandoperationofthesenon-catalytic  
wood heaters. These heaters meet the U.S. Environmental Protection  
Agency’s emissions limits for wood heaters sold on or after July 1, 1990.  
This heater has been developed, tested and constructed in accordance  
with the requirements of UL 1482, ULC S627 and HUD standards and  
is listed by OMNI Test Laboratories, Portland, OR. It has been approved  
for residential, mobile home and alcove installations.  
American National Standards Institute ANSI/NFPA 211, Standard for  
Chimneys, Fireplaces, Vents, and Solid Fuel-Burning Appliances  
- See Draft Section: A chimney or vent shall be so designed and con-  
structed to develop a flow sufficient to completely remove all flue and  
vent gases to the outside atmosphere. The venting system shall satisfy  
the draft requirements of the connected appliance in accordance with the  
manufacturer’s instructions.  
DRAFT REqUIREMENTS  
Your wood stove is dependent upon a properly functioning chimney for  
optimum performance. It is a high efficiency appliance that loses much  
less heat up the chimney than older appliances and fireplaces. For this  
reason it is important to match the stove to the chimney. The chimney  
has two functions:  
Chimney Guidelines:  
• This appliance requires approximately 12 feet minimum of “effective  
draw” provided by the venting system. As a rule of thumb, every 90  
degree total direction change in the venting will result in a loss of  
approximately 5 feet of “effective draw.” Example: If two 45 degree  
offsets are used, subtract 5 feet from the actual vertical vent height  
to determine your “effective draw.” In this case if you had 14 feet of  
vertical vent, the effective draw would only be approximately 9 feet  
(14 ft. - 5 ft. = 9 ft.), therefore it may be necessary to add additional  
height to the venting system.  
• Do not install an offset within the first two feet above the flue outlet  
on the appliance.  
• Inwellinsulatedandweathertighthomes,itmaybedifficulttoestablish  
a good draft up your chimney. The poor draft is caused by a shortage  
of air in the house. In this situation an Outside Air Kit may need to  
be installed (See Negative Pressure Warning on Page 5 and Outside  
Combustion Air on Page 11).  
1. It draws combustion air into the appliance (without air, no fuel will  
burn) and  
2. It exhausts combustion by-products. Your new appliance is what is  
known as a “natural draft” appliance.  
The appliance depends solely on the natural draft of the chimney system  
to draw combustion air into the unit. Draft is the force that moves air  
from the appliance up into the chimney. The amount of draft in your  
chimney depends on the length of the chimney, local geography, nearby  
obstructions and other factors. Too much draft may cause excessive  
temperatures in the appliance (overfiring). Slow or inadequate draft  
equals poor combustion and possible smoking problems. The following  
are some conditions that may contribute to poor chimney draft:  
1. A chimney too large for your appliance.  
2. A chimney with not enough height to produce adequate draft.  
3. A chimney with excessive height (this may allow exhaust to cool too  
much before exiting, which will stall the rate the exhaust exits).  
4. Offsets in the venting system are too restrictive (see Chimney Guide-  
lines).  
Inadequate draft will cause the appliance to leak smoke into the room  
through the stove and the chimney connector joints.  
Chimney Height Requirements  
The chimney must extend 3’ (.92m) above the level of roof penetration  
and a minimum of 2’ (.61m) higher than any roof surface within 10’  
(3m) (see below). Check with your local building officials for additional  
requirements for your area.  
Excessive draft may cause an uncontrollable burn or a glowing red stove  
or chimney part.  
Less than  
10' (3 m)  
Overfiring Damage - If the heater or chimney connector glows, you are  
overfiring. Other symptoms may include: Cracking, warping or burning  
out of components, plated accessories may turn color, stove glass may  
develop a haze, which will not come off with cleaning.  
2’ (610 mm) Min.  
3' (914 mm)  
3'  
Min.  
10'  
(3 m)  
(914 mm)  
Overfiring of a stove is a condition where excessive temperatures are  
reached, beyond the design capabilities of the appliance. The damage  
that occurs from overfiring is not covered under the manufacturer’s  
limited warranty.  
Min.  
Also see Troubleshooting on Page 20.  
Figure 1 - Chimney Height Requirements  
SELECTING THE PROPER VENTING SYSTEM  
To pass inspection in nearly any jurisdiction, the chimney must meet both  
safety and exhaust flow requirements. The (3’ by) 2’ by 10’ rule applies  
to both masonry and factory-built chimneys.  
The appliance is merely one component of a larger system. The other  
equally important component is the venting system. This is necessary for  
achieving the required flow of combustion air to the fire chamber and for  
safely removing unwanted combustion byproducts from the appliance.  
If the venting system’s design does not promote these ends, the system  
maynotfunctionproperly.Poorlyfunctioningventingsystemsmaycreate  
* Ref. USA - National Standard, NFPA 211-latest edition and Canada  
National Standard CSA B365-01-latest edition. Vents installed with a  
listed cap shall terminate in accordance with the terms of the cap’s  
listings.  
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
NEGATIVE PRESSURE WARNING  
FUEL  
This appliance is not designed to be operated in a negative pressure.  
In very airtight homes with large kitchen exhaust fans, furnace cold air  
returns, fresh air exchange systems and any other air system in close  
proximity to the heating appliance may create a negative pressure in the  
same room as the heating appliance. This can create dangerous back  
draftingofthestoveandchimneyjoints,drawingcombustionby-products  
into the home. Be sure your home has adequate makeup air to eliminate  
negative pressures caused by the above-mentioned sources. Outside air  
connected to the appliance probably will not resolve such a problem as  
the stove or fireplace insert is not the source of negative pressure. Lennox  
Hearth Products accepts no liability for damages resulting from negative  
pressures described here.  
Thisunitisdesignedandengineeredtoburn,dry,well-seasonedwoodonly.  
Dry, seasoned wood is that which has been cut, split and allowed to dry  
under a covered area where air is free to flow and circulate under and  
around the wood (not under a tarp or plastic). Make sure wood is not  
stacked directly on the ground, it may absorb moisture from the ground.  
It should be allowed to dry in these conditions for a minimum of six  
months, preferably one year or more. IT MUST BE UNDERSTOOD  
THAT WOOD CANNOT BE LEFT IN ANY KIND OF WET OR DAMP  
AREA OR IT WILL NEVER BECOME COMPLETELY SEASONED.  
Your stove will not operate at the level that it is meant to unless you use  
seasoned, dry wood. Do not burn driftwood or wood that has been in salt  
water, doing so will void your warranty. Do not burn treated wood, coal,  
garbage, cardboard, solvents, or colored paper. Burning treated wood,  
garbage, solvents, or colored paper may result in the release of toxic  
fumes. This type of burning will also void your warranty.  
Ventilation Requirements - Provide adequate air for combustion. The  
fresh air requirements of this appliance must be met within the space  
where it will be installed. Ventilation is essential when using a Solid-Fuel-  
Burning heater. In well insulated and weather tight homes, it may be  
difficult to establish a good draft up the chimney (caused by a shortage  
of air in the home). The lack of air is caused by many common household  
appliances which exhaust air from the home (such as a furnace, heat  
pump, air conditioner, clothes dryer, exhaust fans, fireplaces, and other  
fuel burning appliances). Also, the combustion process of this heater  
uses oxygen from inside the dwelling. If the available fresh air delivery  
in the dwelling is insufficient to support the demands of these appliances,  
problems can result (i.e. excessive negative pressure can develop in the  
dwelling which will affect the rate at which this appliance can draft thus  
resulting in performance problems. To correct this problem it may help  
to open a window (preferably on the windward side of the house) or  
install an optional outside air kit.  
Do Not store fuel within space heater installation clearances or within  
the space required for refueling and ash removal.  
PAINT CURING  
Ifyourstovehasplatedaccessories,besuretocleanitwithahousehold  
type glass cleaner and a very soft cloth to remove any fingerprints and  
residues prior to the first fire and before any fire if the gold has been  
handled or soiled. Do not close the door tightly during the “Burn-In  
Period.”Also,openthedoorfrequently(every5-10minutes)tokeepthe  
gasket from adhering to the curing paint. Ventilate the house well during  
these first firings as the paint gives off carbon dioxide and unpleasant  
odors. It is recommended that persons sensitive to an imbalance in the  
indoor air quality avoid the stove during the curing process.  
CREOSOTE FORMATION AND NEED FOR REMOVAL  
When wood is burned slowly, it produces tar and other organic vapors,  
which combine with expelled moisture to form creosote. The creosote  
vapors condense in the relatively cool chimney flue of a slow-burning  
fire. As a result, creosote residue accumulates on the flue lining. When  
ignited, this creosote makes an extremely hot fire.  
Your new appliance is painted with a high temperature paint that cures  
duringthefirstfewfirings.Werecommendthatyouputyourstovethrough  
a regimen of three burns. The first two should last for 20 minutes each  
at 250 degrees (the stove should be allowed to cool completely between  
each burn). The third should be a burn of at least 450 degrees F. for 45-60  
minutes. The paint will become soft, gummy and emit non-toxic smoke  
during these burns. After the stove cools down for the third time, the  
paint will harden. DO NOT BUILD A LARGE ROARING FIRE UNTIL  
THIS CURING EFFECT IS COMPLETE OR YOU MAY DAMAGE THE  
FINISH OF YOUR STOVE. Spray can touch-ups should be done only  
with a high temperature stove paint (cat. no. H8159), available from all  
Lennox Hearth Products dealers.  
The chimney and chimney connector should be inspected at least once  
monthly during the heating season to determine if a creosote buildup has  
occurred. If creosote has accumulated (1/8” [3 mm] or more), it should  
be removed to reduce the risk of a chimney fire.  
Establish a routine for the fuel, wood burner and firing technique.  
Check daily for creosote build-up until experience shows how often  
you need to clean to be safe. Be aware that the hotter the fire the  
less creosote is deposited, and weekly cleaning may be necessary  
in mild weather even though monthly cleaning may be enough in  
the coldest months. Contact your local municipal or provincial fire  
authority for information on how to handle a chimney fire. Have a  
clearly understood plan to handle a chimney fire.  
BURN-IN PERIOD  
Please be patient with the heat output of your stove for the first few  
weeks. The steel will go through a curing process that eliminates mois-  
ture, which is deep in the steel and firebrick. This moisture will reduce  
initial heat output of your stove and may make it difficult to start. After  
you have broken in the paint on the stove it will be necessary to build  
hot fires to thoroughly remove the moisture from the appliance. Running  
the stove with the draft fully open for 1 to 1-1/2 hours after starting and  
adding generous amounts of fuel during the first week or two should  
complete the curing process. We recommend the use of a thermometer  
attached to the stovetop or chimney. Temperatures on the connector pipe  
should run in the 250-600 degree range. (DO NOT OVERFIRE THE  
STOVE DURING THIS PROCESS. IF THE STOVE OR CHIMNEY  
BECOMES RED, REDUCE THE AMOUNT OF AIR ENTERING THE  
STOVE IMMEDIATELY).  
DISPOSAL OF ASHES  
Ashes should be scooped out of a cool stove with a small metal shovel.  
Ashesshouldbeplacedinametalcontainerwithatightfittinglidandmoved  
outdoors immediately. Other waste shall not be placed in this container.  
The closed container of ashes should be placed on a non-combustible  
floor or on the ground, well away from all combustible materials, pending  
final disposal. If the ashes are disposed of by burial in soil or otherwise  
locally dispersed, they should be retained in the closed container until  
all the cinders have thoroughly cooled. Ashes can ignite up to 72 hours  
after removal from the stove.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chimney and Connector  
CLEARANCES TO COMBUSTIBLES  
Minimum 6" diameter, minimum 24 MSG black steel connector pipe with  
UL103HT listed factory-built chimney suitable for use with solid fuels  
or masonry chimney. Horizontal connection not tested, refer to local  
building codes for installation. See installation instructions for details.  
Restrictions apply! Read instructions before installing.  
WARNING: BEABSOLUTELYSURETHEDISTANCEBETWEENTHE  
HEATERANDTHESURFACEOFANYCOMBUSTIBLECONSTRUC-  
TION IS NOT LESS THAN SHOWN IN THE FIGURES ON PAGE 7.  
Floor Protection  
Residential chimney systems must be from the same brands as listed  
for mobile homes but connector pipe may be double wall, single wall or  
single wall with shield as listed above.  
USA - The floor in front and under the heater must be protected with  
noncombustible material. The covering must extend 16” in front of the  
door opening of the heater and 8” to either side of the door opening.  
This appliance may be vented into a code-approved masonry chimney  
with flue liner.  
Canada - The floor in front and under the heater must be protected with  
noncombustible material. The covering must extend 457 mm in front of  
the door opening of the heater and 200 mm to either side of the stove  
body and 200 mm to the rear or to the wall, whichever is smaller.  
Warning:Chimneyconnectormustbeingoodconditionandkeptclean.  
Do not install damaged parts.  
USA and Canada - A chimney connector / venting extends horizontally  
over the floor, protection must also cover the floor under the connector  
/ venting and at least 2” (51 mm) to either side.  
All of the stove connector pipe used must be of the same brand. The  
chimney that the stove pipe transitions into may be a different brand.  
Other than the transition of the stove pipe into the chimney, do Not mix  
different brand vent components. Install all vent components per vent  
manufacturer’s instructions.  
Reduced Clearances  
The chimney connector shall not pass through an attic or roof space,  
closet or similar concealed space, or a floor, or ceiling. Where passage  
through a wall, or partition of combustible construction is desired, the  
installation shall conform to CAN/CSA-B365, Installation Code for Solid-  
Fuel-Burning Appliances and Equipment.  
Clearances to combustible surfaces can be reduced with the use of listed  
double wall connector pipe. See the clearances with double wall pipe on  
the following page.  
Alcove Clearances:  
Theremustbeaneffectivevaporbarrieratthelocationwherethechimney  
or other component penetrates to the exterior of the structure. Follow the  
vent manufacturer's detailed instructions.  
In alcove installations, only 6” double wall connector pipe can be used  
(single wall or single wall pipe with shield is not allowed). Minimum alcove  
width between combustible materials is 48” (1219 mm). Maximum alcove  
depth is 48” (1219 mm). Minimum alcove height is 72” (1829 mm).  
IMPORTANT NOTE: See Draft Requirements and Selecting a Proper  
Venting System on Page 4 to assist you in choosing the proper venting  
system for your installation.  
Clearance dimensions are to flue collar. If a single wall connector pipe  
with shield is used, a 1 inch air space is needed between pipe and shield.  
Shield attaches to rear of stove pipe and must run from stove top to ceil-  
ing. Pipe shield shall be UL listed.  
Components Required For Installations  
Legs AND Bottom Heat Shield or Pedestal Base. If optional blower is  
NOT used, Rear Heat Shield Block Off Plate shall be installed.  
Use all required components specified for this appliance. Do  
not substitute.  
WARNING: In the event that you remove the blower for any  
reason, make sure a cover plate (available from Lennox Hearth  
Products) is installed before using the heater. Excessive rear  
wall temperatures will result if the stove is burned without the  
cover plate. Note: The cover plate is not necessary if a blower  
has never been installed because a knock-out will be in place  
to act as the cover.  
* Other approved chimney brands are Projet, Jakes Evans/GSW, Dura-  
vent, Metal Fab, Ameri-Tec, Metalbestos and Industrial Chimney (ICC).  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION CLEARANCES - REFER TO FIGURES 2, 3 ANd 4  
PIPE  
Single Wall  
INSTALLATION  
Residential  
A
B (1)  
13-3/4”  
349mm  
C
D (1)  
14-1/2”  
368mm  
E†  
8”  
200mm  
F (1,4)  
9”  
229mm  
USA-16”  
CAN-483mm  
USA-24”  
CAN-635mm  
Residential  
USA-10”  
CAN-330mm  
7-3/4”  
197mm  
USA-24”  
CAN-635mm  
14-1/2”  
368mm  
8”  
200mm  
9”  
229mm  
v
Single w/ Pipe  
Shield  
Double Wall  
Double Wall  
Residential or  
Mobile Home*  
USA-10”  
7-3/4”  
USA-18”  
8-1/2”  
8”  
6”  
CAN-330mm  
197mm  
CAN-483mm  
216mm  
200mm  
152mm  
Alcove  
USA-10”  
CAN-330mm  
7-3/4”  
197mm  
USA-21”  
CAN-559mm  
8-1/2”  
216mm  
8”  
200mm  
6”  
152mm  
PIPE  
Single Wall  
INSTALLATION  
Residential or Alcove  
G (4)  
USA-18”  
CAN-533mm  
H (2)  
USA-37-3/4”  
CAN-1213mm  
I (6)  
USA-51”  
CAN-1422mm  
J (2)  
USA-34-3/4”  
CAN-1048mm  
K
L (5)  
USA 0"  
USA-16”  
CAN-450mm CAN-200mm  
Residential or Alcove  
USA-18”  
CAN-533mm  
USA-37-3/4”  
CAN-1213mm  
USA-45”  
CAN-1270mm  
USA-34-3/4”  
CAN-1048mm  
USA-16”  
USA 0"  
v
Single w/  
CAN-450mm CAN-200mm  
Pipe Shield  
Double Wall  
Air-Cooled  
Residential or Alcove  
or Mobile Home*  
USA-15”  
CAN-450mm  
USA-37-3/4”  
CAN-1213mm  
USA-45”  
CAN-1270mm  
USA-34-3/4”  
CAN-1048mm  
USA-16” USA 0"  
CAN-450mm CAN-200mm  
Double Wall  
Alcove  
N/A  
USA-37-3/4”  
CAN-1213mm  
USA-45”  
CAN-1270mm  
USA-34-3/4”  
CAN-1048mm  
USA-16” USA 0"  
CAN-450mm CAN-200mm  
Top View  
Corner Clearance, Stove and Flue to Wall  
PIPE  
Single Wall  
INSTALLATION  
Residential or Alcove  
M
84”  
2134mm  
T (6)  
USA-61-3/4”  
CAN-1619mm  
Residential or Alcove  
84”  
2134mm  
USA-61-3/4”  
CAN-1619mm  
v
Single w/  
Pipe Shield  
Double Wall  
Air-Cooled  
Residential or Alcove  
or Mobile Home*  
72”  
USA-57-1/2”  
CAN-1727mm  
1829mm  
G
G
F
F
Double Wall  
Alcove  
72”  
1829mm  
USA-57-1/2”  
CAN-1727mm  
T
†
USA=8" (200mm) from door opening, Canada=8" (200mm) from sides and back of unit  
6” Ø Flue Collar  
u
v
Dimensions to Stove Body  
Clearances may only be reduced by means approved by the regulatory authority.  
* Mobile Home - USA only  
Floor  
Protection  
K
Figure 4  
Top View-Parallel Installation  
Footnotes:  
48”  
Max.  
Depth  
1- These dimensions to the stove body are  
forreferenceonly. Actualdistancesshould  
be measured from the stove’s flue collar.  
2- Minimum noncombustible hearth pad  
dimensions.  
B
A
L
Side View-Alcove and  
Parallel Installations  
3- Shield shall be attached to the rear of the  
stovepipewitha1”airspaceandmustrun  
from the top of the stove to the ceiling.  
4- Not applicable to alcove installations.  
5- In corner applications, when installed  
at minimum back wall clearances, the  
required floor protection is dimensioned  
off the back plane of the stove, therefore  
the floor protection required off the back  
corners (at a 45 degree angle) only needs  
to extend to the wall. This situation will  
only occur in CANADA installations.  
6- Reference dimension only, to assist in  
planning the installation.  
C
M
D
I
H
†E  
†E  
K
Floor Protection  
J
FLOOR PROTECTION  
Clearances to connector pipe shall be mea-  
sured from the flue collar of the stove.  
Figure 2  
I
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.  
7
Figure 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Single Wall Pipe  
Using 6” Diameter Single Wall Connector Pipe  
STAINLESS STEEL LINER  
Using 6” Diameter Rigid Stainless Steel Liner  
INSTALL VENTING SYSTEM PER VENT MANUFACTURERS  
INSTRUCTIONS!  
INSTALL VENTING SYSTEM PER VENT MANUFACTURERS  
INSTRUCTIONS!  
Chimney  
Chimney  
Termination  
Cap  
Termination  
Rain Cap  
Shown with Tubinox™ Stainless  
Steel Liner components (see Page  
29 for ordering information)  
Storm  
Collar  
Flashing  
Roof  
Flashing  
Ceiling Support  
Assembly  
Length  
18” (457mm)  
Minimum  
Masonry  
Adaptor  
Slip  
Adaptor  
Single wall stove pipe  
must not pass through  
attics, closets, walls or  
ceilings. It is used to  
connect this appliance  
to a factory built or  
90° Tee  
masonry chimney.  
Fasten each stove pipe  
connection with at least  
3 sheet metal screws.  
Chimney  
Connector  
6” x 24” 24-gage  
black steel or 26  
gage blued steel  
single wall pipe  
Floor  
Protector  
Stove  
Side View  
Fasten stove pipe to  
flue collar with 3 sheet  
metal screws.  
Figure 6 - Connected to a Masonry Chimney  
Floor  
Protector  
Stove  
Side View  
YOUR CHIMNEY INSTALLATION MUST COMPLY WITH LOCAL  
BUILDING AND FIRE CODES.  
Figure 5 - Typical Installation  
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
CHIMNEY INSTALLATION  
Double Wall Pipe  
•
•
Install chimney as per manufacturer’s instructions. Some brands of  
pipe may require removal of the spacer ring in the flue collar.  
All horizontal runs of pipe should be as short as possible and are  
required by NFPA No. 211 to have an upward pitch or rise in the same  
direction the smoke travels of no less than 1/4” to the linear foot. The  
connector pipe must meet minimum clearances in any direction to  
walls or other combustible materials. It must attach to a listed double  
wall metal chimney at least 6” in diameter or to a masonry chimney  
with a flue passage of at least 48 square inches.  
It is required that a chimney connector pipe not extend further than  
the inner wall of the flue when it is connected to a masonry chimney  
and that it either be cemented to the masonry or be installed without  
cement in a thimble connected to the masonry wall. When the  
connector is inserted into a thimble, the joint must be tight enough  
so that it will not be dislodged in normal use. Install connector at  
no less than the minimum clearances from the ceiling when using a  
90-degree elbow to pass through combustible constructions.  
Chimney connector pipes should never pass through a floor, ceiling,  
fire wall, partition, or combustible construction of any type unless  
certain precautions are taken. The best method is to use a listed  
thimble and a listed chimney in accordance with the manufacturer’s  
directions. NFPA No. 211 gives approved methods for passing a flue  
pipe through combustible constructions (see Page 10).  
Using 6” Diameter Type L-Vent Connector Pipe  
Mobile (Manufactured) Home Installation Shown  
INSTALL VENTING SYSTEM PER VENT MANUFACTURERS  
INSTRUCTIONS!  
Mobile home installations  
require a spark arrestor at the  
chimney termination.  
Termination Cap  
with Spark Arrestor  
Remove, if mobile  
home is transported  
•
•
Storm  
Collar  
3 Feet  
Minimum  
Flashing  
Support  
Box  
Fasten each stove pipe  
connection with at least  
3 sheet metal screws.  
Manufactured Home Installations  
(ref. Figure 7)  
All mobile home installa-  
tions require an outside  
air kit (see Page 28 for  
ordering information)  
and the stove must be  
secured to the floor and  
grounded to the mobile  
home chassis.  
DVL Close  
Minimum of  
12-15’ of Flue  
to achieve a  
stable draft.  
Clearance  
This appliance is approved for installation into a manufactured  
(mobile) home in the USA ONLY!  
Connector Pipe  
Installation should be in accordance with the Mobile Home  
Construction and Safety Standard, Title 24 CFR, Part 3280 (in  
Canada CAN/CSA Z240 MH), or, when such a standard is not  
applicable, the Standard for Mobile Home Installations, ANSI  
A225.1.  
7 Feet  
Minimum  
Fasten stove pipe to  
flue collar using 3  
All mobile home installations require an outside air kit (see Page 28  
for ordering information). The stove must be secured to the floor and  
grounded to the chassis of the mobile home.  
sheet metal screws.  
WARNING: DO NOT INSTALL IN SLEEPING ROOM OF A MOBILE  
HOME.  
CAUTION: THESTRUCTURALINTEGRITYOFTHEMOBILEHOME  
FLOOR, WALL AND CEILING/ROOF MUST BE MAINTAINED.  
Floor  
Protector  
SecureStove  
to floor  
Approved Chimney* - Your stove is approved for use with Class A, UL  
103 HT (U.S.) / ULC-S629 (Canada) Listed Residential Type and Building  
Heating Appliance Chimney (HT chimney - 2100° Fahrenheit) and double  
wall connector pipe from Security™ Chimneys.  
Stove  
Side View  
Floor  
Install Outside Air  
Chassis  
Clearancestoconnectorshallbemeasuredfrom6”fluecollar.Restrictions  
apply! Read instructions before installing.  
Kits per instructions  
on Page 11  
Grounded to Steel Chassis  
using a #8 AGW copper  
wire or equivalent.  
YOUR CHIMNEY INSTALLATION MUST COMPLY WITH LOCAL  
BUILDING AND FIRE CODES.  
Figure 7 - Typical Installation  
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chimney Connector Systems and Clearances from Combustible  
Walls for Residential Heating Appliances (NFPA 211) Refer to  
Figure 8  
System A  
Minimum chimney clearance to brick  
and combustibles 2 in. (51mm)  
Minimum clearance  
System A. Minimum 3.5 in. (90 mm) thick brick masonry wall  
framed into combustible wall with a minimum of 12 in. (305 mm)  
brick separation from clay liner to combustibles. Fireclay liner (ASTM  
C 315, Standard Specification for Clay Flue Linings, or equivalent),  
minimum5/8in. (16mm)wallthickness, shallrunfromoutersurface  
of brick wall to, but not beyond, the inner surface of chimney flue  
liner and shall be firmly cemented in place.  
12 in. (305mm)  
of brick  
Chimney  
flue  
Chimney  
connector  
Fire clay  
liner  
Minimum  
Masonry chimney  
constructed to NFPA 211  
Clearance: 12 in. (305 mm)  
12 in. (305mm)  
to combustibles  
System B. Solid-insulated, listed factory-built chimney length of the  
same inside diameter as the chimney connector and having 1 in.  
(25.4 mm) or more of insulation with a minimum 9 in. (229 mm) air  
spacebetweentheouterwallofthechimneylengthandcombustibles.  
Minimum Chimney Clearance from Masonry to Sheet Steel  
Supports & Combustibles – 2 in. (51mm)  
System B  
Min. Clearance  
9 in. (229mm)  
Nonsoluble  
Refractory  
Cement  
The inner end of the chimney length shall be flush with the inside of  
the masonry chimney flue and shall be sealed to the flue and to the  
brickmasonrypenetrationwithnon-water-solublerefractorycement.  
Supports shall be securely fastened to wall surfaces on all sides.  
Factory Built  
Chimney Length  
Chimney  
Connector  
Chimney Length  
Flush with  
Inside of Flue  
UseChimney  
Mfrs.Partsto  
Attach  
Fasteners between supports and the chimney length shall not pen-  
etrate the chimney liner.  
Air Space – 9 in.  
(228.6mm) Min.  
Chimney  
flue  
Connector  
Clearance: 9 in. (229 mm)  
Solid-Insulated  
ListedFactory-  
BuiltChimney  
Length  
Masonry chimney  
constructed to NFPA 211  
SystemC.Sheetsteelchimneyconnector,minimum24gauge[0.024  
in. (0.61 mm)] in thickness, with a ventilated thimble, minimum 24  
gauge [0.024 in. (0.61 mm)] in thickness, having two 1 in. (25.4  
mm) air channels, separated from combustibles by a minimum of 6  
in. (152 mm) of glass fiber insulation. Opening shall be covered, and  
thimble supported with a sheet steel support, minimum 24 gauge  
[0.024 in. (0.61 mm)] in thickness.  
Sheet Steel Supports  
System C  
Minimum chimney clearance to sheet  
steel supportrs and combustibles  
2 in. (51mm)  
2 Air Channels, Each 1  
in. (25.4 mm)  
Supports shall be securely fastened to wall surfaces on all sides and  
shallbesizedtofitandholdchimneysection.Fastenersusedtosecure  
chimney section shall not penetrate chimney flue liner.  
Chimney  
Connector  
Chimney  
flue  
Clearance: 6 in. (152 mm)  
2 Ventilated Air  
Channels, Each  
System D. Solid-insulated, listed factory-built chimney length with  
an inside diameter 2 in. (51 mm) larger than the chimney connector  
and having 1 in. (25.4 mm) or more of insulation, serving as a pass-  
through for a single wall sheet steel chimney connector of minimum  
24 gauge [0.024 in. (0.61 mm)] thickness, with a minimum 2 in.  
(51 mm) air space between the outer wall of chimney section and  
combustibles. Minimum length of chimney section shall be 12 in.  
(305 mm). Chimney section concentric with and spaced 1 in. (25.4  
mm) away from connector by means of sheet steel support plates  
on both ends of chimney section. Opening shall be covered, and  
chimney section supported on both sides with sheet steel supports  
of minimum 24 gauge [0.024 in. (0.61 mm)] thickness.  
1 in. (25.4 mm) Masonry chimney  
Construction of constructed to NFPA 211  
Sheet Steel  
Sheet Steel Supports  
Minimum chimney clearance to sheet steel  
supports and combustibles 2 in. (51mm)  
System D  
Sheet Steel  
Supports  
Min. Clearance  
2 in. (51 mm)  
1 in. (25.4 mm)  
air space to  
chimney length  
Chimney  
Section  
Chimney  
Connector  
Supports shall be securely fastened to wall surfaces on all sides and  
shallbesizedtofitandholdchimneysection.Fastenersusedtosecure  
chimney section shall not penetrate chimney flue liner.  
Chimney connector  
Chimney length  
Sheet Steel Supports  
Masonry chimney  
constructed to NFPA 211  
Air Space – 2 in.  
(51mm) Min.  
Clearance: 2 in. (51 mm)  
Additional requirements:  
Figure 8 - Chimney Connector Systems and Clearances from Combustible Walls  
1.Insulation material used as part of wall pass-through system shall be  
of noncombustible material and shall have a thermal conductivity of  
1.0 Btu-in./hr-ft2 - ºF (4.88 kg-cal/hr-m2 - ºC) or less.  
2.All clearances and thicknesses are minimums; larger clearances and  
thicknesses shall be permitted.  
3.Any material used to close up an opening for the connector shall be of  
noncombustible material.  
4.A connector to a masonry chimney, except for System B, shall extend  
in one continuous piece through the wall pass-through system and the  
chimney wall to the inner face of the flue liner, but not beyond.  
10  
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LEG AND HEATSHIELD INSTALLATION  
Note: The threaded rods used to bolt the legs to the stove are packaged  
with the heatshield, as a heatshield is required when a stove is installed  
on legs.  
Residential and Mobile Homes  
(Bolting down and grounding of stove are required only in mobile  
homes).  
Open all cartons, if any and remove the contents upon receipt and check  
for any damaged or missing parts. If there is hidden damage, notify your  
freight company or Lennox Hearth Products dealer immediately.  
BACK  
Heat Shield  
Mounting Holes  
CAUTION: Wear gloves during installation in case of sharp  
edges on the stove.  
FRONT  
Air Channel  
Leg Installation  
Figure 10  
1. Carefully place stove on it’s back. Be careful not to scratch the  
stove, use a piece of cardboard or carpet to protect the back of  
the stove.  
OUTSIDE AIR KIT INSTALLATION  
2. Mount all four legs as shown in Figure 9.  
3. First, screw the threaded rods into the holes at the four corners  
on the bottom of the stove. Screw the threaded rods into the  
firebox three full rotations or 3/16 to 1/4”, (if the rear rods are  
screwed in too far they will lift the bricks off the bottom of the  
stove). Use a washer and nut to secure the leg. Be sure the  
legs are mounted squarely on the firebox bottom. Tighten nuts  
securely.  
4. Use the two bolts and washers provided with the heatshield kit  
to mount the heatshield as shown in Figure 10.  
5. Do not over tighten the heatshield mounting bolts as it may bend  
the heatshield.  
To install the “Outside Air Kit,” position the clip so that the nut is directly  
above the hole punched in the back of the heatshield (See Figure 11).  
Install the outside air adapter box on the stove by sliding it into the air  
channellocatedbetweenthebottomheatshieldandthestovebottomuntil  
the oblong ring is approximately 1/4” from the rear edge of the lower  
heatshield. Make sure the ring is facing down. Thread the 1/4” bolt up  
through the nut in the clip until snug against the adapter box.  
Expanded View of Clip  
Line up the hole in the clip with the hole in the  
rear center of the bottom heatshield  
Threaded Rod  
Washer  
Nut  
Clip  
1/4” Bolt  
Figure 11  
To locate the hole in the hearth for outside air, mark a 4” circle on the  
hearth. The circle’s center should be 2-3/4” directly back from the center  
of the flue outlet and 5/8” to the left side.  
Figure 9  
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14. All horizontal runs of pipe should be as short as possible and are  
required by NFPA No. 211 to have an upward pitch or rise in the same  
direction the smoke travels of no less than 1/4” to the linear foot.  
The connector pipe must meet minimum clearances in any direction  
to walls or other combustible materials. It must attach to a listed  
double wall metal chimney at least 6” in diameter or to a masonry  
chimney with a flue passage of at least 48 square inches.  
15. It is required that a chimney connector pipe not extend further than  
the inner wall of the flue when it is connected to a masonry chimney  
and that it either be cemented to the masonry or be installed without  
cement in a thimble connected to the masonry wall. When the  
connector is inserted into a thimble, the joint must be tight enough  
so that it will not be dislodged in normal use. Install connector at  
no less than the minimum clearances from the ceiling when using  
a 90-degree elbow to pass through combustible constructions.  
16. Chimney connector pipes should never pass through a floor, ceiling,  
fire wall, partition, or combustible construction of any type unless  
certain precautions are taken. The best method is to use a listed  
thimble and a listed chimney in accordance with the manufactures  
directions. NFPA No. 211 gives approved methods for passing a  
flue pipe through combustible constructions.  
STOVE INSTALLATION  
1. If not previously installed, install floor protection and move the  
heater into the desired location.  
2. Position the stove on your floor protection in the exact location  
where it is to be located, making sure all minimum clearances are  
met.  
3. If you are installing outside air on your stove, mark a 4” circle on  
the floor protection just below the oblong ring. When cut out, this  
hole will accommodate the flexible outside air tube.  
4. If the stove is to be fastened to the floor, locate the hold down  
brackets inside the leg box and mark the floor protection below the  
holes in the brackets.  
5. If you are installing outside air on your stove, remove the stove and  
cut the floor protection and the floor where the 4” air tube circle had  
been previously drawn. If the stove is to be fastened to the floor,  
drill 1/2” holes through the floor protection only, at the marks that  
were for fastening the stove to the floor if so desired. Slip the flexible  
outside air tube through the hole in the floor, leaving 1” of tube above  
the floor protector surface, using tape to hold it in place.  
6. Place the stove on the floor protection so that the previously cut or  
drilled holes line up. Attach the stove to the floor with the lag bolts  
if so desired.  
7. If you are installing outside air on your stove, place the hose clamp  
over the flexible air tube and slide the tube up over the 4” ring on  
the outside air adaptor box and tighten the hose clamp. Push the  
outside air adaptor forward 1/4” until full contact is made with the  
lower heatshield. Tighten the 1/4” bolt until the adaptor box is held  
firmly in place. Use silicone sealant to create a seal between the  
flexible air tube and your floor protection.  
8. If it is necessary to level, secure, or ground your stove, use the holes  
in the bottom of the leg for those applications. To level the stove  
on Olympic cast legs, locate the front leg that is not touching the  
hearth pad. Insert the allen head screw through the slotted washer  
(supplied with the legs) and into the threaded hole in the bottom of  
the leg. See the drawing to the right. Push the slotted washer down  
until it touches the hearth pad and then tighten the screw into the  
leg. Should any other leg not be resting on the hearth pad, install a  
washer and screw in that leg as well.  
9. Install bricks and baffle as per instructions on Pages 14 and 15.  
It is highly recommended that the baffle be assembled before the  
chimney is installed so that the baffle blankets can be adjusted into  
place through the flue collar.  
Insert the allen  
head screw  
through the  
slotted washer  
10. If installed into a mobile home, the stove shall be grounded to the  
mobile home chassis with a #8 AGW copper wire or equivalent.  
11. For residential installations, install the first section of stove pipe  
with the crimped end going down inside the flue collar on the heater.  
Continue with your stove pipe, installing each section-crimped  
end down. Make the final connection to your chimney. Your dealer  
carries the necessary pipe and fittings to connect to the various  
listed factory-built chimneys. YOUR CHIMNEY INSTALLATION MUST  
COMPLY WITH LOCAL BUILDING AND FIRE CODES.  
Figure 12  
12. Be sure to fasten each stove pipe connection with at least 3 sheet  
metal screws.  
13. Install chimney as per manufacturer’s instructions. Some brands of  
pipe may require removal of the spacer ring in the flue collar.  
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. If required, install the Outside Air Kit (P/N 71112) as per the fol-  
lowing instructions. To locate the hole in the hearth for outside  
air mark and cut a 4” (102 mm) hole in the hearth. The hole’s  
center should be 3” (76 mm) directly forward from the center  
of the flue outlet or locate as per the following instructions.  
6. Position the stove on your floor protection in the exact location  
where it is to be located, making sure all minimum clearances  
are met. Mark the floor protection where the pedestal will be  
located, then remove the stove.  
7. Make four 1-1/2” (38 mm) cuts in one end of the corrugated  
tube and fold the flaps back. Cut a 4” (102 mm) hole through  
the floor protection and the floor and insert the corrugated tube  
into the hole. Cover it with the supplied screen and fasten it to  
the floor protector.  
PEDESTAL INSTALLATION  
(For ash drawer pedestal see instructions included with pedestal)  
Residential and Mobile Homes  
(Bolting down and grounding are required only in mobile homes)  
CAUTION: Wear gloves during installation in case of sharp  
edges on the stove.  
1. Remove the heater from the carton, if packaged, upon receipt  
and check for any damaged or missing parts.  
2. Carefullyputthestoveonpedestalwiththeopenendofthepedestal  
facing the rear. DO NOT LEAVE THE STOVE UNATTENDED  
UNTIL IT IS BOLTED SECURELY TO THE PEDESTAL.  
3. Lineuptheholesinthebracketsonthepedestalwiththethreaded  
holes in the bottom of the stove. Use the two 1/2” long bolts  
and 3/8” standard washers to bolt the stove to the pedestal. Be  
sure to see that the stove is mounted squarely on the pedestal  
before tightening the two bolts securely.  
4. When installing a pedestal on this stove you MUST plug the four  
leg mounting bolt holes, located on the bottom of the stove in  
the four corners, with the bolts that were used to mount the  
shipping legs. The two rear bolts should not be installed more  
thantwofullrotationstopreventliftingthebricksoffthebottom  
of the stove. FAILURE TO INSTALL THESE FOUR BOLTS  
PROPERLYWILLRESULTINREDUCEDCONTROLOFTHE  
STOVE’S COMBUSTION SYSTEM!  
8. Locate the 11-1/2” x 14” (292 mm x 356 mm) metal plate and  
paint to match the stove if necessary. Position this piece so that  
the 14” (356 mm) dimension evenly overlaps the lips on the back  
of the pedestal (see drawing below). Attach this plate to the back  
of the pedestal with the self-tapping screws supplied.  
9. If the stove is to be fastened to the floor, attach the stove with  
the supplied lag bolts, through the pedestal base on opposite  
sides, attaching them into the floor beneath the floor protection.  
Seal any irregularities with silicone sealer.  
10. If installed in a mobile home, the heater shall be grounded to the  
chassis with a #8 AGW copper wire or equivalent.  
11. Install bricks as per instructions on Pages 14 and 15. It is highly  
recommended that the baffle be assembled before the chimney  
is installed so that the baffle blankets can be adjusted into place  
from the flue outlet.  
12. Install chimney as per manufacturer’s instructions.  
Block Off Plate is  
Required When  
Installing Outside  
Air Into Unit (Plate  
is Included With  
Kit # 71112)  
Figure 13  
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
POST INSTALLATION CHECKS  
BRICK INSTALLATION  
CAUTION: Wear gloves during brick installation in case of  
sharp edges inside the stove.  
1. Check that all chimney pipe joints are securely fastened.  
2. Check that the heater is securely fastened to the floor (if ap-  
plicable).  
Note: Installation of the baffle boards and baffle blankets are easier when  
you can still access the flue outlet, (before connecting the flue vent). Be  
sure the baffle blankets are placed flat on the baffle boards so as not  
to block exhaust flow to the flue. Use a ruler or a piece of kindling to  
reach over the baffle blanket to be sure it is completely flat on top of the  
baffle boards.  
3. Make sure the intake vent has clear access to outside air (if ap-  
plicable).  
4. Make sure the outside air vent has been sealed properly to keep  
rodents out (if applicable).  
Measure bricks before installing, as per list of dimensions on next  
page, to be sure the correct bricks are installed in the correct location.  
5. Be sure all roof flashings are watertight.  
1. Install bricks #1-26 in the numbered sequence shown in Figure  
6. Be sure the stove is properly grounded (if applicable).  
14 on Page 15.  
FOR YOUR OWN PROTECTION AND INSURANCE PURPOSES,  
HAVE YOUR CHIMNEY AND CONNECTOR PIPE INSTALLATION  
INSPECTED BY YOUR LOCAL BUILDING CODE AUTHORITY OR  
FIRE MARSHAL BEFORE STARTING A FIRE IN YOUR STOVE.  
NOTIFY YOUR INSURANCE COMPANY.  
Note: Beforeinstallingyourbaffleboardsmakesurethestainless  
steel tube support and front and rear tube hangers are centered  
side to side and that the front and rear hangers are hooked onto  
the stainless steel pins protruding from the rear of the airwash  
and the stove back.  
2. Next,youwillinstallthebaffleboards. All4baffleboardsincluded  
are the same size. You will start by installing the boards in the  
center part of the unit on top of the secondary tubes to each side  
of the baffle support with the 15” side of the baffle board going  
from the front to back of the unit. Once you have the first two  
boards installed slide the board to the left side of the baffle sup-  
port all the way to the left and rear of the unit. You will slide the  
board to the right side of the secondary support to the right and  
rear of the unit. Next you will install the two remaining boards  
where you originally installed the first two boards on each side  
of the baffle support and pushed against the rear of the unit. The  
stainless steel support hanger should be centered left to right  
between the sets of baffle boards and placed as shown in Figure  
15 on Page 15.  
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Also included with the unit are two 15” x 10” x 1” thick baffle blankets. Install each blanket above the baffle board to each side of the second-  
ary support with the 15” side of the blanket from front to rear of the unit. Make sure that the baffle blankets are to the full rear of the unit.  
CAUTION: Make sure the baffle blankets are down flat on the baffle boards, pulled together in the center so that no gaps  
exists between them and do not protrude beyond baffle boards. It is critical that baffle boards and baffle blankets are fully  
against the rear of the unit.  
These brick sizes may be slightly smaller to adjust for steel and firebrick tolerances beyond our control. Be sure to measure and mark bricks  
with their numbers when removing.  
WARNING: IF THE BRICKS ARE NOT INSTALLED EXACTLY AS SHOWN BELOW, THEY COULD FALL OUT OF PLACE DURING RE-  
FUELING OR BURNING OF THE STOVE CAUSING SERIOUS INJURY.  
Firebox Brick Layout as Viewed from the Front  
24  
E
25  
H
26  
E
Brick Sizes  
B = 4-1/2”x 5-1/2”  
1
F
2
F
3
G
4
F
5
F
10*  
F
6*  
F
E = 3”x 9”  
11  
F
7
F
F = 4-1/2”x 9”  
G = 1-1/2”x 9”  
H = 1-1/2”x 3”  
K = 1-1/2”x 5-1/2”  
S = 2-1/8”x 9”  
8
F
12  
F
14  
F
15  
F
17  
F
18  
F
16  
G
13  
S
9
S
23  
B
19  
B
22  
B
21  
K
20  
B
* Bricks 6 and 10 fit up against the back of the firebox.  
Figure 14  
Baffle Insulation Parts  
Side Cut-A-Way View of Firebox  
15”  
Baffle Blankets  
1” Thickness  
Two Baffle Blankets Per Unit  
Baffle  
Board  
10”  
15”  
Firebox  
Brick  
1/2” Thickness  
Four Boards Per Unit  
4-3/4”  
Figure 15  
Figure 16  
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATING HINTS  
STARTING AND MAINTAINING A FIRE  
Be sure to clean plated accessories with a household type  
cleaner and a very soft cloth to remove any fingerprints and  
residues prior to the first fire.  
1. Burn only dry, well-seasoned wood for maximum heat output. In some  
states it is illegal to burn wet wood or anything other than clean, dry  
wood products.  
2. Your stove is designed to operate with the door closed! Operate only  
with the door shut tightly at all times except when loading wood and  
possibly on start up to establish a draft. Never leave the unit unat-  
tended while the front door is slightly opened.  
1. NEVER USE FLAMMABLE LIqUIDS TO START OR REKINDLE  
A SOLID FUEL FIRE!!  
3. DONOThitormovethebaffleboardswhileloadingwood.Occasionally  
check the baffle. Make sure the baffle blankets are always flush with  
the front of the baffle boards. Loading oversized logs may dislodge  
the baffle boards.  
4. CAUTION: THE DRAFT CONTROL MUST BE FULLY OPEN BE-  
FOREOPENINGTHEDOORTOAVOIDPOSSIBLECOMBUSTION  
FLASH!! (Ignition of hot volatile gases as the door is opened).  
5. Feeding excessive amounts of fuel to the stove should be avoided.  
It is important to supply it with sufficient draft and fuel to maintain a  
moderatelyhotfire.If,duringovernightburns,heavycreosotedeposits  
develop inside your stove and on the door, the draft is set too low  
- review your burning habits!  
2. Fully open the primary draft control by pulling the 1” plastic knob  
out on the left side (lower front corner) until it stops (away from the  
stove). This control determines the amount of air entering the stove.  
Pushing it toward the stove reduces the burn rate in the firebox. For  
your convenience, the rod on this control is marked with four grooves  
to assist you in obtaining repeatable burn rates.  
3. Place a small amount of crumpled paper in front of the firebox and  
cover it with a few pieces of kindling.  
4. Light the paper and allow sufficient time for the kindling to become  
fully engulfed in flames. You will now close the wood units front door.  
(Your wood units front door may or may not need to be left slightly  
open during this start up process, this depends on the stove model  
and the amount of draft present. Do not leave the unit unattended  
while the front door is slightly open) Once kindling is burning well,  
larger pieces of wood may be added, then the door should be fully  
closed if there was the need to keep it slightly open during start up.  
CAUTION  
Be careful not to abuse door assembly by striking or  
slamming it. If the door assembly or glass is broken or  
damaged, they must be replaced with factory original  
parts before heater can be safely operated. Use only  
components provided by the manufacturer as replace-  
ment parts.  
DO NOT LEAVE THE STOVE UNATTENDED WHILE THE FRONT  
DOOR IS SLIGHTLY OPEN.  
CAUTION: Do Not alter the adjustment range of the draft  
control for increased firing for any reason.  
OK  
Operate only with fuel door and ash drawer closed. Maintain  
allsealsingoodcondition.Donotoperatewithbrokenglass.  
Do Not build the fire too close to the glass.  
Donotoperatetheappliancewiththedooropenorajarother  
than possibly during start up to create a draft (Do not leave  
the unit unattended while the front door is slightly open dur-  
ing start up). Operating the appliance with the door open  
other then in initial start up if needed will produce extreme  
temperatures within the appliance. Damage caused from  
over-firing is not covered under the manufacturers limited  
warranty.  
5. For best results, use smaller pieces of wood to get the insert tem-  
perature very high before loading larger wood for sustained burns.  
If necessary, crack the door to allow ignition of the fuel charge. Do  
not leave the unit unattended while the front door is slightly open.  
Now you can add larger pieces of wood and after several minutes of  
high burn, set the left control for the desired heat output. Check the  
exhaust in about 15 to 20 minutes. Large amounts of smoke indicate  
an improper burn setting (either too high or too low). Adjust and  
recheck in 5 to 10 minutes.  
Figure 17  
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BLOWER OPERATION  
Blower Operation  
The blower can be operated manually or automatically (blower will  
turn on when the stove is hot and turn off when the stove is cool).  
The rocker switch on the control panel allows you to select between  
manual operation or automatic operation as follows (see Figure 19):  
MANUAL OPERATION: Turn rocker switch to the “MANU-  
AL” position and adjust rheostat knob to the desired speed. The blower  
will have to be manually turned “OFF” by rotating the rheostat knob  
clockwise until it clicks.  
Blower Speed Control  
Knob (rheostat)  
Manual / Auto  
Rocker Switch  
Figure 19 - Blower Controls  
AUTO OPERATION: Turn rocker switch to the “AUTO” posi-  
tion and the rheostat to the ON position (rotate rheostat knob coun-  
terclockwise until it clicks). When the stove warms up, the blower will  
automatically turn on (adjust rheostat knob to the desired speed set-  
ting). When the stove cools down, the blower will automatically turn  
off.  
WARNINGS  
The blower must be plugged directly into a properly  
groundedthree-prongreceptacle,120VAC,60Hz,single  
phase. Do not cut or remove the grounding prong from  
this plug. Do not route power cord under or in front of  
appliance.  
Rheostat Operation - The highest blower speed is obtained by turn-  
ing the rheostat knob counterclockwise until it clicks “ON”, then rotate  
towards “HIGH” to increase blower speed. Rotate the knob clockwise  
for a lower speed. To turn off, continue to rotate the knob clockwise  
until it clicks “OFF.”  
Installation must be in accordance with National Elec-  
trical Code, ANSI/NFPA 70 - latest edition. In Canada,  
the current CSA C22-1 Canadian Electrical Code - latest  
edition.  
Blower Operation Guidelines  
While in auto operation mode, the blower will turn off and on based on  
the temperature of the appliance. Auto operation ensures there is suffi-  
cient heat build-up to warm the air being moved by the blower before the  
blower is turned on. Likewise, when the appliance cools off, the blower  
is turned off to prevent circulating cool air. Depending on the size and  
intensity of the fire it may be necessary to adjust the blower speed ac-  
cordingly to ensure un-interrupted blower operation. For example a small  
fire may require a slower blower speed to keep the heat output by the  
blower consistent. If the blower is operated in manual mode, it may be  
necessary to adjust the blower speed as the fire begins to burn down and  
the appliance is no longer hot enough to effectively heat the air moved  
by the blower. If the air coming from the blower feels cool, one should  
either decrease the blower speed or stoke the fire to build up more heat.  
DANGER: Disconnect power before servicing blower.  
In the event that you remove the blower for any reason,  
make sure a cover plate (available from Lennox Hearth  
Products)isinstalledbeforeusingtheheater.Excessive  
rear wall temperatures will result if the stove is burned  
withoutthecoverplate. Thecoverplateisnotnecessary  
ifablowerhasneverbeeninstalledbecauseaknock-out  
will be in place to act as the cover.  
AUTO-RESET  
TEMPERATURE  
NOTE: Turn blower off before opening the door to load the fuel.  
ROOM AIR  
SWITCH N/O  
BLOWER  
TWO POSITION  
SWITCH  
MANUAL/TEMPERATURE  
NOTE: SWITCH CONDITIONS  
GIVEN AT ROOM TEMPERATURE  
N/C = NORMALLY CLOSED  
N/O = NORMALLY OPEN  
3-RED  
1-BRN  
3-RED  
YLW  
= FEMALE DISCONNECT  
= MALE DISCONNECT  
= STUD CONNECTION  
3-RED  
1-BRN  
WHT  
SPEED  
CONTROL/OFF  
POWER CORD  
4-GRN  
4-GRN  
BLK  
Figure 18 - Blower Wiring Schematic  
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATING TECHNIqUES AND HINTS  
ACHIEVING CLEAN, LONG BURNS  
Recentdevelopmentsinwoodburningtechnologyhavemadewoodburning  
a cleaner and more convenient way to heat your home. Overall efficiency  
in a wood burning appliance is a combination of combustion efficiency  
and heat transfer efficiency. Whether heating your entire home or just a  
room or two, your understanding of how to best operate your stove or  
insert will enhance its overall efficiency and performance. What this can  
mean to you is longer, cleaner burns, less wood use and more heat.  
To achieve long burn times, after having thoroughly preheated the  
stove, let the stovetop cool down to 275 to 400 degrees (on Elites,  
locate thermometer on the face of the insert just above the door). Now  
load the firebox and set the draft control. At this point, you may need to  
burn the stove with the draft open for a few minutes to ignite the wood.  
All Lennox Hearth Products stoves are EPA tested for emissions at low  
burn with the air control completely closed. Whether or not you should  
burn your stove with the air control completely closed will depend on  
the following factors:  
GETTING THE MOST OUT OF YOUR STOVE  
*
*
*
*
*
How you load your wood  
Your chimney type, height and draft  
Your wood type and its moisture content  
The temperature of the stove  
The following sections will outline techniques you can use to “get the  
most out of your stove.” Please read them carefully.  
Which model stove or insert you have  
MAXIMIZING YOUR STOVE’S OVERALL EFFICIENCY  
Experiment with different loading configurations to achieve longer  
burns. Try loading the wood from side to side and nesting it in the ashes  
to prevent airflow under and around the wood. Fresh wood should be  
loaded to the back of the firebox or to the sides. Hot coals or half burned  
wood should be brought towards the front of the firebox. The way you  
load your wood can seriously affect burn times. If the new load does not  
ignitewithinafewminutes,trycrisscrossingtheloadtoallowmoreairflow  
around the fire, or try a slightly hotter stove temperature.  
It is important to know that for high, combustion efficient, clean burns,  
you will need to have sufficient temperatures inside the firebox for  
thorough combustion. The best method for determining if you have  
sufficient temperatures is to watch the brick lining in your firebox. When  
you first light your stove, the bricks will turn a dark brown or black.  
After 20 to 30 minutes of a hot fire, most of the bricks should return  
to near their original light brown or yellow color. This means the bricks  
have reached a high enough temperature for your stove to achieve high  
combustion efficiency.  
Determining the lowest setting for efficient low burns. This will require  
some experimentation on your part. Try closing the air control all the  
way with the stove temperature at 325 to 350 degrees. If the flames are  
completely extinguished, open the air control halfway and then slowly  
close it until there is only a small amount of flame. It is important to check  
the stove about 20 minutes after setting the draft control as it takes this  
long for the stove temperature to stabilize. There should still be some  
small flames on or above the wood load.  
Second and just as important, is achieving a high level of heat transfer  
efficiency. Slowing the rate of flow through the stove or insert enhances  
heat transfer, thus allowing more time for heat to be transferred into your  
home. To do this, be sure to thoroughly preheat your stove and then  
reduce the amount of primary air by closing the draft control (lower left)  
to about 1/2 to 3/4 open. This will decrease the excess oxygen in your  
flue, which carries heat up your chimney, but should still be enough  
air to allow the stove to produce its maximum heat output. (More air  
may produce a slightly greater amount of heat, but will greatly increase  
wood consumption). When the area being heated reaches a comfortable  
temperature, slow the burn rate by closing the control to further improve  
heat transfer.  
Use 325 degrees as a starting point. You can try starting temperatures  
25degreeshigherorlowertoachievedesiredburntimes, start25degrees  
lower if the stove burns the wood too quickly or 25 degrees higher if there  
are no flames in the firebox for more than a few minutes after loading the  
wood. You may or may not need to burn the stove with the air control  
open for a few minutes prior to setting the draft for a low burn, this will  
depend on the factors mentioned above. Be sure not to smolder a fire  
overnight. Check your chimney for large amounts of smoke as this  
indicates very poor combustion.  
To get the most out of your appliance, you will need to combine good  
combustion efficiency with good heat transfer practices. The following  
are some tips on how to operate your stove to achieve the highest overall  
efficiency.  
It is important to realize that stove technology has changed. Stoves  
have changed a great deal in the last few years. This has led to substantial  
changes in the methods of operation in new stoves as compared to older  
stoves. In old stoves without full brick linings and ceramic insulation,  
the rule was “get the stove as hot as possible before setting the draft on  
low for overnight burns.” On newer, high technology stoves, this is not  
necessary. Although it is still important to have the stove hot enough to  
burn efficiently, it will require less preheating. Once you have determined  
your optimum operating temperatures for various burn rates, we believe  
you will find your stove an extremely convenient way to achieve your  
heating needs.  
1. Thoroughlypreheatyourstovebeforeslowingtheburnratebyclosing  
the draft control.  
2. Measure the stove temperature at the hottest point on the stove top  
or face. Use this information to repeat burn rates.  
3. Once preheated, add wood (if needed) and partially close the draft  
control (lower left).  
4. Operate your stove as much as possible in the low to medium burn  
ranges.  
5. Do not lower the draft setting so low as to completely extinguish the  
flames in the firebox. Check for at least some small flames twenty  
minutes after setting the draft control.  
6. Do not continually operate your stove in the high (wide open) setting.  
This wastes wood by carrying a great deal of heat up the chimney  
and can damage your stove and chimney.  
7. Go outside and check your chimney. More than a very small amount  
of smoke indicates wasted heat, creosote build up and pollution.  
Do not reload the stove for long burns when the stainless secondary  
tubes or baffles are glowing red, or when the stove is uncomfortably  
hot to load. This indicates the stove is too hot to load for a long burn.  
Also, do not load wood for a long burn on a deep bed of hot coals. Try  
stirring the coals a few minutes before loading the stove for a low burn  
to allow some of the unburned coals time to burn.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
CAUTION  
Cleaning Glass: Ensure appliance is cold prior  
to cleaning glass. A commercial glass cleaner  
designed for stoves is recommended. Do not use  
abrasivecleaners.Donotcleanwithanymaterials,  
which may scratch or otherwise damage the glass.  
Scratches on the glass can develop into cracks or  
break. Inspect the glass regularly. If you detect a  
crack, extinguish the fire and contact your dealer  
for a replacement.  
DOOR HINGES: If door hinges need lubricating, use an anti-seize com-  
pound (never use oil) available from your Lennox Hearth Products dealer.  
DOOR LATCH: If your door latch fails to latch tightly and the gasket is  
in good condition, place a length of pipe (cheater bar) over the inside  
portion of the door handle and bend slightly toward the door until the  
proper adjustment is obtained. If the door handle does not close easily,  
apply high temperature anti-seize to the striker.  
DOOR GASKET: Periodically check gasket to make sure it is not over-  
compressed. If compressed, replace with a special woven Door Rope.  
(Don’t try substituting rope, only use special Lennox Hearth Products  
Door Rope).  
GLASS REPLACEMENT INSTRUCTIONS  
PLATED ACCESSORIES: Clean only with household type glass cleaner  
and a very soft cotton cloth. Other products may damage plated finish,  
paint and gaskets.  
Step 1. Remove Door Assembly - Open door to remove E clip from the upper  
hinge pin. Remove upper hinge pin by pulling up while holding the op-  
posite side of the door. Lift door out of the lower hinge pin and place  
face down on a soft surface.  
Step 2. Remove Door Back Screws (6 ea.) - Using a 5/32” allen wrench remove  
the 6 retainer screws from the faceplate. To locate screws, peel back the  
door gasket as necessary.  
Step 3. Disassemble Door Assembly - Flip door assembly over to be face up.  
Separate faceplate from door back by pulling up on faceplate.  
Step 4. Remove Glass - Carefully remove broken glass one piece at a time  
(protective gloves are recommended)  
BAFFLE BLANKET: Your baffle blankets should be inspected during every  
chimney cleaning. If the baffle blanket is compressed or heavily stained,  
it should be replaced. Heavy creosote stains or matting is an indication  
of improper use and your burning habits should be reviewed.  
GLASS CLEANING: Only clean glass with products specifically made to  
use on wood stoves. Other products could damage gaskets and paint.  
Never scrape glass with a razor blade. This can pit the glass and make it  
impossible to clean in the future.  
WINDOW GASKET: The window gasket can be checked by running the  
flame of a match near the gasket and around the door. If the flame is  
drawn in around the window, the gasket should be replaced.  
Step 5. Install New Glass Assembly - Install the new glass with gasket in recess  
on door back (use only factory supplied 5mm ceramic glass. Do not  
substitute).  
Step 6. Reinstall Faceplate and Screws - Reinstall faceplate onto door back  
and while holding the door assembly together flip the assembly back  
onto it’s face. Carefully reinstall the screws. Be very careful not to  
overtighten the screws (this could result in glass breakage when the  
stove or fireplace insert is hot) and it is highly recommended to use anti  
seize on the screws.  
Step 7. Reinstall Door - Set door assembly back into the lower hinge mount  
while holding the handle side of the door up. Place the upper hinge  
pin back in the mount and door assembly. Reinstall the E clip that was  
removed.  
DOOR HANDLE: Door handle may become tight as you use the stove.  
Free the handle up by using dry graphite supplied with the stove. The  
directions are included with the graphite.  
WARNING  
Inspectandcleanchimneyandconnectorfrequently.  
Under certain conditions of use, creosote buildup  
may occur rapidly.  
GLASS CLEANING GUIDELINES  
Door Gasket  
WARNING: DO NOT CLEAN GLASS WHEN APPLIANCE IS HOT!  
Screws and  
Washers  
Glass on any wood stove or fireplace insert will not stay perfectly clean.  
Here are some guidelines for cleaning and caring for the glass:  
•
•
Ensure the stove or fireplace insert is cold prior to cleaning glass.  
This appliance is designed to provide a flow of air over the inside of  
the glass, where along with high heat helps inhibit build-up on the  
glass. When build-up occurs, a commercial glass cleaner designed  
for stoves is recommended. Regular household glass cleaners will  
not clean creosote.  
Door Back  
•
•
Do not use abrasives such as steel pads, steel wool or oven cleaner  
as they will scratch the glass. Never scrape glass with a razor blade  
as this may pit the glass and make it impossible to clean in the future.  
Do not use chemical glass cleaners as they may damage the gaskets  
or painted surfaces.  
Handle Rod  
Glass  
Glass Gasket  
TIPS FOR KEEPING THE GLASS CLEAN  
•
•
Burn only dry seasoned cord wood. Wet wood = Dirty glass.  
A short, hot fire (15 - 20 minutes) may help to clean off some of the  
normal buildup. Lower burns = more build-up. Higher burns = less  
build-up.  
Faceplate  
•
•
Keep freshly loaded wood away from the glass.  
After reloading, allow all the wood to catch flame before dampering  
down the stove or fireplace insert.  
Figure 20  
19  
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING  
Problem  
Solution  
POOR DRAFT:  
Extend chimney in length or have the chimney realigned to the proper size flue. Oversized chimneys normally have  
poor drafts. Remember, the stoves’ draft depend solely on the natural draft of the chimney (See Draft Requirements on  
Page 4). If your stove is not drafting properly, your chimney is the problem. All stoves are thoroughly tested to ensure  
proper draft with the correct size chimney flue.  
EXCESSIVE DRAFT:  
DIRTY GLASS:  
With better chimneys being more common, excessive draft can be an issue. Alleviate excessive draft by slowing the  
burn rate of the stove once it has reached proper operating temperature (See Maximizing Your Stoves Overall Efficiency  
on Page 18).  
1) Burn smaller, hotter fires and check to make sure you are not setting the draft down too far with the draft control.  
2) Make sure your wood is well-seasoned and dry (not open to rain - see Creosote and Fuel sections on Page 5).  
3) See Poor Draft section (above) and Cleaning Glass on Page 16.  
SMOKES WHEN  
DOOR IS OPEN:  
1) If smoke is entering the room, check to make sure your baffle boards are properly installed  
and that the baffle blankets are pushed back flush with the front of the baffle boards.  
2) Check the chimney for blockage due to creosote (see Chimney and Creosote sections on Pages 5 and 6).  
3) Check draft (See POOR DRAFT section above).  
WOOD BURNS  
TOO FAST:  
1) The draft control must be closed further.  
2) Add fuel at lower firebox temperatures.  
3) Load wood side to side and reduce the flow of air under wood.  
4) The door seal may need replacing, check for leakage.  
5) See “Excessive Draft.”  
POOR HEAT OUTPUT:  
1) Check your wood. Wet, moist, unseasoned wood will not produce heat.  
2) Your stove needs to be seasoned (moisture removed from the steel and brick). Continue to burn a fire. It normally  
takes from one to three weeks of burning to season your stove (See Burn-In Period on Page 5).  
3) See Excessive Draft section above.  
PAINT GIVES OFF  
ODOR (smoke):  
Paint is tempering-in. Burn only moderately hot for the first few days until paint is fully cured.  
Then burn a very hot fire to cure any paint that may not easily cure. Open windows or door to ventilate (See Burn-In  
Period on Page 5).  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DO’S AND DON’TS  
DO NOT: Install or operate this stove before reading this manual.  
DO NOT: Close the draft beyond the point at which the flames are completely extinguished.  
DO NOT: Open the stove door without fully opening the draft first.  
DO NOT: Burn driftwood or wood that has been in salt water. This includes some mill ends and scrap lumber that has been floated in salt water  
on the way to the mill. (This will void your warranty).  
DO NOT: Handle the plated faceplate unnecessarily. Use the door handle only.  
DO NOT: Force oversized logs into the firebox as this may dislodge the baffle assembly.  
DO NOT: Close the door tightly during Burn-In Period.  
DO:  
Be sure to clean any fingerprints from the Gold or Nickel faceplate before burning the stove. Clean the Gold or Nickel door only with a  
household type glass cleaner and a very soft cloth.  
DO:  
DO:  
Consult local building department if other than recommended clearances are desired.  
Read instructions for the baffle boards and baffle blankets occasionally to ensure you have not bumped or moved them out of place  
when loading wood.  
DO:  
DO:  
DO:  
DO:  
Check the chimney and baffle monthly to make sure they are clean.  
Burn seasoned, dry wood only! (RAIN = WET WOOD)  
Open the door frequently during Burn-In Period to keep gasket from adhering to the curing paint.  
Enjoy the warm feeling of your new Lennox Hearth Products appliance.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
20  
21  
H5558 Single Black Cascade Leg  
REPLACEMENTPARTS-MODELSSS210,ST210ANDSWS210  
H5669 Single Black Olympic Leg  
H5622 Single Gold Olympic Leg  
Contact an Lennox Hearth Products dealer to obtain any of these  
parts.Neverusesubstitutematerials.Useofnon-approvedparts  
can result in poor performance and safety hazards.  
H5621 Single Nickel Olympic Leg  
H5620 Single Brushed Gold Olympic Leg  
H5619 Single Brushed Nickel Olympic Leg  
H5649 Heatshield / Leg Fastener Kit  
71115 Bottom Heatshield / SS210, ST210 and SWS210  
H5662 Cascade / Olympic Leg Kit Outside Air Plenum Box  
FSB BLOWER PARTS  
FRONT DOOR PARTS LIST  
22  
23  
24  
Item # Cat. No  
Description  
1
2
3
4
6
7
H5639 Door Rope Kit, 7/8” Dia. (6’ 2”)  
H5629 Upper Hinge Pin  
H5626 Upper Hinge Pin E-Clip  
25  
H8062 FSB700 Blower Only Assembly w/ blower wiring  
harness  
H5628 Lower Hinge Pin  
26  
27  
28  
29  
30  
31  
H5658 Fan Blade (FSB700)  
H5640 Glass Gasket Kit (8’ 4”)  
H5657 Fan Cage (FSB700)  
H5577 Set of 6 screws and 6 washers for door assembly  
H5654 Spring Handle / Nickel  
H8063 FSB700 Blower Only Wire Harness  
H8064 Snap Switch w/gasket and screws  
H5742 Speed Control - High Temperature (FSB700)  
8
H5653 Spring Handle / Gold  
71067 Traditional Door Glass / Plain  
71068 Traditional Door Glass / Sailboat  
71063 Traditional Door Glass / Cattail  
71065 Traditional Door Glass / Evergreen  
71066 Traditional Door Glass / Floral  
71057 Traditional Door Faceplate / Black  
71058 Traditional Door Faceplate / Gold  
71059 Traditional Door Faceplate / Nickel  
71148 Traditional Door Faceplate / Brushed Gold  
71145 Traditional Door Faceplate / Brushed Nickel  
71072 Arch Door Glass / Plain  
H8065 Control Panel Assembly w/ Snap Switch Housing  
Assembly  
9
32  
H8066 Control Switch (Manual, Off, Automatic)  
MISCELLANEOUS PARTS  
71052 Dry Graphite (Apply to door handle and door hinges)  
H5633 Anti Seize 2 gram pouch  
71134 Stainless Steel Pipe Reducer from 8” to 6”  
SS210, ST210 AND SWS210 STOVE PARTS  
H5627 Removable Inner Flue Collar Ring  
H8079 Nameplate Kit w/ Hardware - Silver  
H8080 Nameplate Kit w/ Hardware - Gold  
H5650 Draft Rod Knob  
10  
11  
12  
33  
34  
71073 Arch Door Glass / Sailboat  
71069 Arch Door Glass / Cattail  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
46  
H8081 Ash Block Off - Hearthplate  
71070 Arch Door Glass / Evergreen  
71071 Arch Door Glass / Floral  
H5661 Cast Iron Ash Plug  
H5582 1/2 Cut Brick for Ash Removal  
H5612 Firebrick 4-1/2” x 9” (14 per stove)  
H5606 Firebrick 4-1/2” x 5-1/2” (4 per stove)  
H5605 Firebrick 3” x 9” (2 per stove)  
H5611 Firebrick 2-1/8” x 9” (2 per stove)  
H5599 Firebrick 1-1/2” x 9” (2 per stove)  
H3096 Firebrick 1-1/2” x 5-1/2” (1 per stove)  
H5603 Firebrick 1-1/2” x 3” (1 per stove)  
71060 Arch Door Faceplate / Black  
71061 Arch Door Faceplate / Gold  
71062 Arch Door Faceplate / Nickel  
71147 Arch Door Faceplate / Brushed Gold  
71144 Arch Door Faceplate / Brushed Nickel  
13  
14  
H5579 Traditional Door Back w/ Handle (door gasket  
included)  
H5578 Arch Door Back w/ Handle (door gasket included)  
ASH DRAWER PEDESTAL & PEDESTAL  
H5571 Complete Baffle/Secondary Burn Tube Assembly  
(includes tubes and all mounting hardware)  
15  
16  
17  
18  
19  
H5514 Small & Large Pedestal Rear Block Off Plate w/ Hole  
H5556 Ash Drawer for Large Pedestal  
47  
48  
H8019 Baffle Blankets 15-1/4” x 12-1/2” x 1” - Two Included  
H8018 Baffle Board Kit w/ Baffle Blankets  
H5564 Ash Plug Remover and Rake  
H5516 Aluminum Flex Tubing Kit w/ clamp (15” of 4” dia.)  
H5565 6” x 6-1/2” Rodent Screen  
LEGS AND LEG PARTS  
18  
H5516 Aluminum Flex Tubing Kit w/ clamp (15” of 4” dia.)  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPLACEMENT PARTS - MODEL SS210  
33  
48  
34  
47  
46  
35  
41  
45  
38  
41  
39  
39  
37  
39  
39  
42  
39  
43  
39  
39  
39  
39  
39  
39  
42  
39  
43  
39  
39  
36  
40  
40  
44  
40  
40  
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPLACEMENT PARTS - MODEL ST210 AND SWS210  
33  
34  
48  
47  
46  
35  
41  
45  
41  
39  
38  
39  
39  
42  
37  
39  
39  
43  
39  
39  
39  
39  
39  
43  
39  
39  
39  
39  
42  
36  
40  
40  
44  
40  
40  
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.  
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPLACEMENT PARTS - MODELS SS210, ST210 AND SWS210  
Door Parts  
2
3
1
2
1
3
14  
4
11  
5
8
13  
6
4
9
5
7
8
6
7
12  
10  
Blower Parts  
25  
27  
28  
26  
29  
31  
30  
32  
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPLACEMENT PARTS - MODELS SS210, ST210 AND SWS210  
Leg and Leg Parts  
23  
20  
22  
24  
18  
21  
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPLACEMENT PARTS - MODELS SS210, ST210 AND SWS210  
Ash Drawer Pedestal and Pedestal  
18  
19  
15  
17  
18  
16  
19  
15  
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ACCESSORIES - MODELS SS210  
ACCESSORIES - MODELS ST210 AND SWS210  
Product Reference Information  
Product Reference Information  
Description  
Cat. No.  
H7886  
H8404  
Description  
Ship.  
Weight  
Ship.  
Volume  
Cat. No.  
H7885  
Ship.  
Weight  
Ship.  
Volume  
424 lb.  
424 lb.  
20.74 cu. ft.  
20.74 cu. ft.  
ST210A-B, Stove / Step Top / Arch  
Black Door / Nickel Nameplate  
411 lb.  
26.23 cu. ft.  
SS210T-B, Stove / T Top / Traditional  
Black Door / Nickel Nameplate  
SWS210, Stove / Step Top / Arch Black  
Door  
PEDESTALS (REqUIRED)  
PEDESTALS (REqUIRED)  
Cat. No.  
71113  
71114  
Model  
WL-PED  
Description  
Cat. No.  
71113  
Model  
WL-PED  
Description  
Pedestal (ref. form #506033-16)  
Pedestal  
WL-PED-ASHD  
Ash Drawer Pedestal (ref. form #506033-15)  
71114  
WL-PED-ASHD  
Ash Drawer Pedestal  
OR LEGS (REqUIRED) (ref. form #506033-14)  
OR LEGS (REqUIRED)  
70000  
70001  
70002  
70007  
LEG-OLY-B  
LEG-OLY-G  
LEG-OLY-N  
LEG-OLY-BRG  
Olympic Sculptured Black Legs (4 per pkg.)  
Olympic Sculptured Gold Legs (4 per pkg.)  
Olympic Sculptured Nickel Legs (4 per pkg.)  
70000  
70001  
70002  
70007  
LEG-OLY-B  
LEG-OLY-G  
LEG-OLY-N  
LEG-OLY-BRG  
Olympic Sculptured Black Legs (4 per pkg.)  
Olympic Sculptured Gold Legs (4 per pkg.)  
Olympic Sculptured Nickel Legs (4 per pkg.)  
Olympic Sculptured Brushed Gold Legs  
(4 per pkg.)  
Olympic Sculptured Brushed Gold Legs (4  
per pkg.)  
70008  
70003  
LEG-OLY-BRN  
LEG-CAS-B  
Olympic Sculptured Brushed Nickel Legs  
(4 per pkg.)  
70008  
70003  
LEG-OLY-BRN  
LEG-CAS-B  
Olympic Sculptured Brushed Nickel Legs (4  
per pkg.)  
Cascade Steel Black Legs (4 per pkg.)  
Cascade Steel Black Legs (4 per pkg.)  
HEAT SHIELD (REqUIRED WITH LEGS)  
HEAT SHIELD (REqUIRED WITH LEGS)  
71115  
WSHS-210  
Heat Shield (ref. form #506033-14)  
71115  
WSHS-210  
Heat Shield  
FACEPLATE KITS (INCLUDES FACEPLATE, HANDLE AND NAMEPLATE)  
H7901 ARCH-FPK-BG Arch Faceplate/Brushed Gold  
H7902 TRAD-FPK-BG-SM Sm - Traditional Faceplate/Brushed Gold  
FACEPLATE KITS (INCLUDES FACEPLATE, HANDLE AND NAMEPLATE)  
H7901  
H7902  
H7904  
H7905  
ARCH-FPK-BG  
Arch Faceplate/Brushed Gold  
TRAD-FPK-BG-SM Sm - Traditional Faceplate/Brushed Gold  
H7904  
H7905  
ARCH-FPK-G  
Arch Faceplate/Gold  
ARCH-FPK-G  
Arch Faceplate/Gold  
Traditional Faceplate/Gold  
BLOWER  
TRAD-FPK-G-SM Traditional Faceplate/Gold  
BLOWER  
TRAD-FPK-G-SM  
H7917  
BLWR-FSB700-SS Blower Kit, FS Woodstoves  
OUTSIDE AIR KITS  
H7917  
BLWR-FSB700-SS Blower Kit, FS Woodstoves  
OUTSIDE AIR KITS  
71111  
71112  
OUTAIRK-L  
OUTAIRK-P  
Outside Air Kit / Leg (ref. form #506033-18)  
71111  
71112  
OUTAIRK-L  
OUTAIRK-P  
Outside Air Kit / Leg  
Outside Air Kit / Pedestal  
MISC.  
Outside Air Kit / Pedestal (ref. form #506033-17)  
MISC.  
71053 Paint Gold (1/2 Pint) Paint Gold (1/2 pint)  
71053  
71054  
H8159  
Paint Gold (1/2 Pint) Paint Gold (1/2 pint)  
PaintNickel(1/2Pint)  
TSPK-B  
71054  
H8159  
Paint Nickel (1/2 pint)  
Paint Nickel (1/2 Pint)  
TSPK-B  
Paint Nickel (1/2 pint)  
Touch-Up Paint , Metallic Black, 12 oz.  
Aerosol  
Touch-Up Paint , Metallic Black, 12 oz.  
Aerosol  
H5308  
W-LEGF-LBRKT  
Leg Fastening L - Brackets (4 per pkg.) (Tie  
down kit to be used in mobile or modular  
homes) (ref. form #506033-19)  
H5308  
W-LEGF-LBRKT  
Leg Fastening L - Brackets (4 per pkg.) (Tie  
down kit to be used in mobile or modular  
homes) (ref. form #506033-18)  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Secure Black™ Single Wall Stove Pipe  
6” SW Pipe and Accessories  
ACCESSORIES - MODELS SS210, ST210 AND SWS210  
Security Chimneys™ Pipe  
Cat. No.  
6SWL6  
Model  
Description  
LENGTH 6” X 6”  
Pc. / Container  
6SWL6  
100  
5
6SWL12  
6SWL24  
6SWL36  
6SWL48  
6SWLT  
6SWL12 LENGTH 6” X 12”  
6SWL24 LENGTH 6” X 24”  
6SWL36 LENGTH 6” X 36”  
6SWL48 LENGTH 6” X 48”  
Tubinox Components  
10  
2
6” Rigid Stainless Steel Liner  
Cat. No.  
6LL6  
Model  
6LL6  
Description  
LENGTH 6” X 6”  
Pc. / Container  
5
4
4
4
4
4
4
4
10  
4
4
4
4
5
1
5
5
4
4
4
6SWLT  
6SWLA  
6SWMA  
6SWT  
TELESCOPIC LENGTH 6” (42”-  
1
6LL12  
6LL24  
6LL36  
6LL48  
6L7A  
6LL12  
6LL24  
6LL36  
6LL48  
6L7A  
LENGTH 6” X 12”  
66”)  
LENGTH 6” X 24”  
6SWLA  
6SWMA  
ADJUSTABLE LENGTH 6”  
(3”- 9”)  
5
1
LENGTH 6” X 36”  
LENGTH 6” X 48”  
SINGLE WALL MASONRY  
ADAPTOR 6”  
ADJUSTABLE LENGTH (7 to 11)  
SPLIT BASE TEE  
6SWT  
TEE 6” (TEE CAP INCLUDED)  
2
4
6LT  
6LT  
6SWE45  
6SWE90  
6SWE45 ELBOW 45 DEGREE 6”  
6SWE90 ELBOW 90 DEGREE 6”  
6LTCS  
6LTC  
6LTCS  
6LTC  
TEE CAP  
4
TWIST LOCK TEE CAP  
ELBOW 30 DEGREE  
ELBOW 45 DEGREE  
ELBOW 90 DEGREE  
FLASHING  
6SWE90A 6SWE90A SWIVEL 90 DEGREE ELBOW 6”  
10  
10  
8
6LE30  
6LE45  
6LE90  
6LST  
6LE30  
6LE45  
6LE90  
6LST  
6UP  
6UP  
FLUE EXTENSION 6”  
6SWAB  
6SWIN7  
6SWIN8  
6SWOA  
6SWLK  
6PB  
6SWAB  
6SWIN7  
6SWIN8  
6SWOA  
6SWLK  
6PB  
STOVE ADAPTOR 6”  
INCREASER LENGTH ( 6”- 7”)  
INCREASER LENGTH (6”- 8”)  
OVAL TO ROUND ADAPTOR 6”  
DAMPER UNIT 6”  
4
4
6LSTSS  
6LSA  
6LSTSS  
6LSA  
FLASHING STAINLESS  
SUPPORT ASSEMBLY  
INTERIOR SUPPORT  
ADAPTOR FLEX PIPE (MALE)  
ADAPTOR FLEX PIPE (FEMALE)  
5
4
6LSB  
6LSB  
DECORATIVE COLLAR 6”  
(ASHT)  
25  
6LAAM  
6LAAF  
6LLFLEX  
6LAAM  
6LAAF  
6LLFLEX  
6PF  
6PF  
TRIM COLLAR 6” (ASHT)  
5
STAINLESS FLEXIBLE LENGTH  
(6”X60”)  
Double Wall Black Stove Pipe  
6” DL Pipe and Accessories  
6LMA  
6LLR5  
6LLW7  
6LCC  
6LMA  
6LLR5  
6LLW7  
6LCC  
MASONRY ADAPTOR  
REDUCER LENGTH (6”-5”)  
INCREASER LENGTH (6”-7”)  
DELUXE RAIN CAP  
1
4
4
1
1
1
Cat. No.  
6DL6  
Model  
Description  
LENGTH 6” X 6”  
Pc. / Container  
6DL6  
6DL12  
6DL24  
6DL36  
6DL42A  
6DL3A  
6DL36A  
6DT  
8
4
2
2
1
4
2
4
4
4
6DL12  
6DL24  
6DL36  
6DL42A  
6DL3A  
6DL36A  
6DT  
LENGTH 6” X 12”  
6LCS  
6LCS  
REGULAR RAIN CAP  
LENGTH 6” X 24”  
6LRSMI  
6LRSMI  
ADJUSTABLE INSULATION  
WALL THIMBLE 6” - 12”  
LENGTH 6” X 36”  
TELESCOPIC LENGTH (42” 66”)  
ADJUSTABLE LENGTH (3”- 9”)  
ADJUSTABLE LENGTH ( 3”-34”)  
TEE (TEE CAP INCLUDED)  
ELBOW 45 DEGREE  
6DE45  
6DE90  
6DMA  
6UP  
6DE45  
6DE90  
6DMA  
6UP  
ELBOW 90 DEGREE  
MASONRY ADAPTOR 1  
FLUE EXTENSION 10  
6DAB  
6DAB  
STOVE ADAPTOR 8  
6DLW7  
6DLW8  
6DLK  
6DLW7  
6DLW8  
6DLK  
INCREASER LENGTH ( 6”- 7”)  
INCREASER LENGTH (6”- 8”)  
DAMPER UNIT DL 6”  
DECORATIVE COLLAR  
TRIM COLLAR  
4
4
4
6DqDH  
6Dq  
6DqDH  
6Dq  
25  
10  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cat. No.  
Model  
Description  
Pc. / Container  
ACCESSORIES - MODELS SS210, ST210 AND SWS210  
Supports (continued)  
6SM  
6SM  
TEE SUPPORT  
1
5
Secure Temp® Factory-Built Chimney  
6” Secure Temp ASHT and Secure Temp G-ASHT  
6SMA  
6SMA  
GALVALUME ADJUSTABLE TEE  
SUPPORT (2” TO 6”)  
Cat. No.  
Model  
Description  
Pc. / Container  
SO  
SO  
OFFSET SUPPORT / WALL SUP-  
PORT  
10  
Lengths and Fittings  
6L8  
6L12  
6L18  
6L24  
6L36  
6L48  
6LA  
6L8  
6L12  
6L18  
6L24  
6L36  
6L48  
6LA  
LENGTH 6” X 8”  
1
1
ST  
ST  
ROOF SUPPORT  
FLOOR SUPPORT  
ANCHOR PLATE  
Braces and Firestops  
FIRESTOP  
10  
5
LENGTH 6” X 12”  
6SD  
6SP  
6SD  
6SP  
LENGTH 6” X 18”  
1
10  
LENGTH 6” X 24”  
1
LENGTH 6” X 36”  
1
6BF  
6BF  
10  
LENGTH 6” X 48”  
1
6RSM30 6RSM30 ANGLED FIRESTOP - 30 DEGREE  
ADJUSTABLE LENGTH, 12”  
INSULATED TEE (TCS INCLUDED)  
1
6RS  
6RS  
RADIATION SHIELD  
5
1
6TI  
6TI  
1
6RSA2  
6RSA2  
2PC INSULATED ATTIC RADIATION  
SHIELD  
6TCS  
6TCS  
INSULATED SS TEE CAP (INCLUDED  
WITH TI)  
10  
6ARSA  
6ARSA  
ADJUSTABLE INSULATED ATTIC  
RADIATION SHIELD  
1
6TB  
6TBS  
6TBD  
6TB  
6TBS  
6TBD  
BASE TEE GALVANIZED (TC IN-  
CLUDED)  
1
1
1
6RSI  
6RSI  
INSULATED RADIATION SHIELD  
INSULATED WALL THIMBLE  
1
1
BASE TEE STAINLESS (TCS IN-  
CLUDED)  
6RSM  
6RSM  
6RSMI30 6RSMI30 30-DEGREE RADIATION SHIELD  
1
BASE TEE GALVANIZED DOUBLE (TC  
INCLUDED)  
BS2  
BM  
BS2  
BM  
UNIVERSAL ROOF BRACE  
UNIVERSAL WALL BAND  
1
6TC  
6TC  
BASE TEE CAP GALVANIZED  
10  
5
10  
10  
6TCI  
6TCI  
INSULATED TEE CAP (USE WITH  
SME SUPPORT)  
6BH  
6BH  
GUY WIRE BAND (WIRE NOT  
INCLUDED)  
6TCP  
6TCP  
DRAIN TEE CAP (USE WITH SME  
SUPPORT)  
5
6FR  
6FR  
FLAT ROOF FLASHING  
3
3
6FAR  
6FAR  
ADJUSTABLE ROOF FLASHING -  
1/12- 7/12  
6E15  
6E30  
6E15  
6E30  
INSULATED ELBOW 15 DEGREE  
INSULATED ELBOW 30 DEGREE  
2
1
6FARA  
6FBR  
6FARA  
6FBR  
ADJUSTABLE MALLEABLE ALUMI-  
NUM ROOF FLASHING 1/12 - 7/12  
Aluminum Zinc Coated Steel (Lengths and Fittings)  
6GL8 LENGTH 6” X 8”  
ADJUSTABLE ROOF FLASHING -  
8/12- 12/12  
3
6GL8  
6GL12  
6GL18  
6GL24  
6GL36  
6GL48  
6GLA  
1
1
6GL12 LENGTH 6” X 12”  
6GL18 LENGTH 6” X 18”  
6GL24 LENGTH 6” X 24”  
6GL36 LENGTH 6” X 36”  
6GL48 LENGTH 6” X 48”  
6FBRA  
6FBBR  
6FBRA  
6FBBR  
ADJUSTABLE MALLEABLE ALUMI-  
NUM ROOF FLASHING 8/12 - 12/12  
1
ADJUSTABLE ROOF FLASHING  
12/12 - 21/12  
3
1
1
6FPR  
6FPBR  
6FC  
6FPR  
6FPBR  
6FC  
PEAK ROOF FLASHING 1/12 -7/12  
PEAK ROOF FLASHING 8/12 -12/12  
STORM COLLAR  
3
3
1
6GLA  
6GTI  
6TCS  
ADJUSTABLE LENGTH, 12”  
1
10  
6GTI  
INSULATED TEE (TCS INCLUDED)  
1
Chimney Termination  
RAIN CAP  
6TCS  
INSULATED SS TEE CAP (INCLUDED  
WITH GTI)  
10  
6CC  
PE  
6CC  
PE  
1
UNIVERSAL SPARK ARRESTER  
BAND  
10  
6GE15  
6GE30  
6GE15 INSULATED ELBOW 15 DEGREE  
2
1
6GE30 INSULATED ELBOW ALUM-ZINC 30  
DEGREE  
Chimney Accessories  
DECORATIVE TRIM  
6PF  
6PB  
6PA  
6PD  
6PF  
6PB  
6PA  
6PD  
5
25  
1
Supports  
DECORATIVE COLLAR  
BLACK PIPE ADAPTOR  
FINISHING CONE  
6UP  
PS  
6UP  
PS  
FLUE EXTENSION  
10  
1
SqUARE CATHEDRAL SUPPORT  
EXTENSION  
1
6SSC  
6SSAC  
6SFC  
6SSC  
SqUARE CATHEDRAL SUPPORT W/  
1
1
1
Fireplace Components  
COUPLER  
6EK-1  
6IK  
6EK-1  
6IK  
EXTERIOR KIT (INCLUDES 1 TI, 1  
TCI, 1 SME, 1 RSM, 1 CC, 1 PB,  
1 BM)  
1
1
6SSAC ADJUSTABLE SqUARE CATHEDRAL  
SUPPORT w/COUPLER  
6SFC  
FINISHING SUPPORT W/COUPLER  
INTERIOR KIT (INCLUDES 1 SFC, 1  
RSA2, 1CC)  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY / LISTING LABEL - ENGLISH  
2011  
2012 2013  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY / LISTING LABEL - FRENCH  
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. The part number.  
4. The description of the part.  
5. The quantity required.  
WARRANTY  
Your wood appliance is covered by a limited warranty (provided with the  
appliance). Please read the warranty to be familiar with its coverage.  
6. The installation date of the appliance.  
If you encounter any problems or have any questions concerning the  
installation or application of this system, please contact your dealer.  
Retain this manual. File it with your other documents for future refer-  
ence.  
LENNOX HEARTH PRODUCTS  
1508 Elm Hill Pike, Suite 108  
Nashville, TN 37210  
visit us at www.Lennox.com  
1-800-9-LENNOX  
REPLACEMENT PARTS  
See Pages 22 through 27 for a complete replacement parts list. Use  
only parts supplied from the manufacturer.  
Normally, all parts should be ordered through your Lennox distributor or  
dealer. Parts will be shipped at prevailing prices at time of order.  
PRODUCT REFERENCE INFORMATION  
Werecommendthatyourecordthefollowingimportantinformationabout  
your appliance. If you did not purchase your appliance directly from a  
Lennox Hearth Products dealer, then please call 1-800-9-LENNOX for the  
name and phone number of your nearest Lennox Hearth Products dealer  
who will answer your questions or address your concerns.  
When ordering repair parts, always give the following information:  
1. The model number of the appliance.  
2. The serial number of the appliance.  
Your Appliance’s Model Number _______________________________________  
Your Appliance’s Serial Number________________________________________  
The Date On Which Your Appliance Was Installed __________________________  
Your Dealer's Name _________________________________________________  
LennoxHearthProductsreservestherighttomakechangesatanytime,withoutnotice,indesign,  
materials, specifications, prices and also to discontinue colors, styles and products.  
Consult your local distributor for fireplace code information.  
Printed in U.S.A. © 2007 by Lennox Hearth Products  
P/N 775215M Rev. F 09/2011  
1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  

KTI Networks Network Card KG 502T User Manual
La Crosse Technology Thermometer WS 7215U IT User Manual
Lennox Hearth Indoor Fireplace SOLANA BK User Manual
LG Electronics Blu ray Player BD300 User Manual
LG Electronics Clothes Dryer DLE2140W User Manual
Lightolier Indoor Furnishings 1078 User Manual
Mackie DJ Equipment HD1221 User Manual
Maxtor Computer Drive STM3160215A User Manual
Melissa Espresso Maker 245 007 User Manual
Memorex Handheld TV MT0501 User Manual