LG Electronics Computer Monitor W2261V User Manual

User’s Guide  
W2261V  
Make sure to read the Important Precautions before using the product.  
Keep the User's Guide(CD) in an accessible place for future reference.  
See the label attached on the product and give the information to your  
dealer when you ask for service.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Precautions  
On Installation  
Do not allow anything to rest upon or roll over the power cord, and do not place the  
display where the power cord is subject to damage.  
Do not use this display near water such as near a bathtub, washbowl, kitchen sink,  
laundry tub, in a wet basement, or near a swimming pool.  
Displays are provided with ventilation openings in the cabinet to allow the release of  
heat generated during operation. If these openings are blocked, built-up heat can  
cause failures which may result in a fire hazard. Therefore, NEVER:  
Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.  
Place the display in a built-in enclosure unless proper ventilation is provided.  
Cover the openings with cloth or other material.  
Place the display near or over a radiator or heat source.  
Main power breaker is the power cord and this breaking device must be located at  
a location where it is easy to operate.  
Do not rub or strike the Active Matrix LCD with anything hard as this may scratch,  
mar, or damage the Active Matrix LCD permanently.  
Do not press the LCD screen with your finger for a long time as this may cause  
some afterimages.  
Some dot defects may appear as Red, Green or Blue spots on the screen.  
However, this will have no impact or effect on the display performance.  
If possible, use the recommended resolution to obtain the best image quality for  
your LCD display. If used under any mode except the recommended resolution,  
some scaled or processed images may appear on the screen. However, this is  
characteristic of the fixed-resolution LCD panel.  
Leaving a fixed image on the screen for a long time may cause damage to the  
screen and cause image burn-in. Make sure to use a screen saver on the product.  
Burn-in and related problems are not covered by the warranty on this product.  
On Cleaning  
Unplug the display before cleaning the face of the display screen.  
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display  
screen because over-spraying may cause electrical shock.  
On Repacking  
Do not throw away the carton and packing materials. They make an ideal  
container in which to transport the unit. When shipping the unit to another  
location, repack it in its original material.  
On Disposal  
The fluorescent lamp used in this product contains a small amount of mercury.  
Do not dispose of this product with general household waste.  
Disposal of this product must be carried out in accordance to the regulations of  
your local authority.  
A2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting the Display  
Connecting the stand  
1
.
2.  
Place the monitor with its front facing downward on a soft cloth.  
Assemble the stand base into stand body in the correct direction as shown in  
the picture, then tighten the screw which is attached to the stand base.  
Stand Base  
Screw  
Stand Body  
3.  
Once assembled take the monitor up carefully and face the front side.  
Disassembling the stand  
1. Place the monitor face down on the cushion or soft cloth.  
2. Loosen the screw which is attached to the stand base, then take off the stand base  
from stand body.  
Stand Body  
Stand Base  
Screw  
Important  
This illustration depicts the general model of connection. Your monitor may differ from  
the items shown in the picture.  
Do not carry the product upside down holding only the stand base. The product may  
fall and get damaged or injure your foot.  
A3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting the Display  
Before setting up the monitor, ensure that the power to the monitor, the computer  
system, and other attached devices is turned off.  
Positioning your display  
1. Adjust the position of the panel in various ways for maximum comfort.  
Tilt Range: -5˚~17˚  
Ergonomic  
It is recommended that in order to maintain an ergonomic and comfortable viewing  
position, the forward tilt angle of the monitor should not exceed 5 degrees.  
A4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting the Display  
Using the Computer  
1. Make sure to turn off the computer and product. Connect the cable as below sketch map  
1
2
form  
to  
.
A
B
C
D
Connect DVI Cable  
Connect Dsub Cable (PC)  
Connect Dsub Cable (Mac)  
Connect HDMI Cable  
NOTE  
This is a simplified representation of the rear view.  
This rear view represents a general model; your display may differ from the view as  
shown.  
User must use shielded signal interface cables (D-sub 15 pin cable, DVI cable) with  
ferrite cores to maintain standard compliance for the product.  
Signal Cable  
Power Cord  
Headphone/Earphone Input  
Wall-outlet type  
AV equipment  
(Set-Top Box, DVD, Video,  
Video Game Console)  
DVI-D(This feature is not  
available in all countries.)  
Mac adapter  
For Apple Macintosh use, a separate plug adapter is needed  
to change the 15 pin high density (3 row) D-sub VGA  
connector on the supplied cable to a 15 pin 2 row connector.  
A5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting the Display  
2. Touch the power button on the front of panel to turn  
the power on. When monitor power is turned on, the  
'Self Image Setting Function' is executed  
automatically. (Only to the D-sub signal cable input  
(RGB))  
Power button  
NOTE  
'
Self Image Setting Function'? This function provides the user with optimal display settings.When the user  
connects the monitor for the first time, this function automatically adjusts the display to optimal settings for  
individual input signals.  
'AUTO/SET Function'? When you encounter problems such as blurry screen, blurred letters, screen flicker  
or tilted screen while using the device or after changing screen resolution, touch the AUTO/SET function button  
to improve resolution.  
A6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Control Panel Functions  
Front Panel Controls  
Control  
Function  
FUN Button  
Use this button to enter EZ ZOOMING, 4:3 IN WIDE,  
PHOTO EFFECT, SOUND items, for more information,  
refer to page A15-A16.  
Use this button to enter or exit from the On Screen Display.  
MENU Button  
OSD LOCKED/UNLOCKED  
This function allows you to lock the current control settings, so  
that these settings are not inadvertently changed. To lock the  
OSD settings, press and hold the MENU button for several  
seconds. The message "OSD LOCKED" appears.  
You can unlock the OSD settings at any time by  
pushing the MENU button for several seconds. The  
message "OSD UNLOCKED" appears.  
A7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Control Panel Functions  
Control  
Buttons  
Button  
Function  
Use these buttons to select or adjust functions in the On  
Screen Display.  
For more information, refer to page A17~A18.  
(
)
Use this button to make RGB, DVI or HDMI connector  
active. This feature is used when two computers are  
connected to the display. The default setting is RGB.  
*HDMI is optimized on the AV equipment.  
Button  
(SOURCE)  
Use this button to select an icon in the On Screen  
Display.  
AUTO/SET  
Button  
AUTO IMAGE ADJUSTMENT  
When adjusting your display settings, always press  
the AUTO/SET button prior to entering the On  
Screen Display(OSD). This will automatically adjust  
your display image to the ideal settings for the  
current screen resolution size (display mode).  
The best display mode is:  
W2261V : 1920 x 1080  
Use this button to turn the display on or off.  
Operate key up to Red decoration area around  
button even back side.  
Power Button  
This Indicator lights up as red when the display is  
operating normally(On Mode). If the display is in  
Sleep Mode (Energy Saving), this indicator color  
changes to flicker.  
Power Indicator  
A8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
On Screen Display (OSD) Control Adjustment  
Screen Adjustment  
Making adjustments to the image size, position and operating parameters of  
the display is quick and easy with the On Screen Display Control system.  
A short example is given below to familiarize you with the use of the controls.  
The following section is an outline of the available adjustments and selections  
you can make using the OSD.  
NOTE  
Allow the display to stabilize for at least 30 minutes before making image adjustments.  
To make adjustments in the On Screen Display, follow these steps:  
Press the MENU Button, then the main menu of the OSD appears.  
To access a control, use the  
or  
Buttons. When the icon you want  
becomes highlighted, press the AUTO/SET Button.  
Use the  
/
Buttons to adjust the image to the desired level. Use the  
AUTO/SET Button to select other sub-menu items.  
Push the MENU Button once to return to the main menu to select another  
function. Push the MENU Button twice to exit from the OSD.  
A9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
On Screen Display(OSD) Selection and Adjustment  
The following table indicates all the On Screen Display control, adjustment,  
and setting menus.  
: Adjustable  
R : RGB Input  
D : DVI Input  
H : HDMI Input  
* : only for RGB/DVI Input  
** : only for HDMI Input  
NOTE  
The order of icons may differ depending on the model (A10~A18 ).  
A10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
On Screen Display(OSD) Selection and Adjustment  
You were introduced to the procedure of selecting and adjusting an item  
using the OSD system. Listed below are the icons, icon names, and icon  
descriptions of the all items shown on the Menu.  
Press the MENU Button, then the main menu of the OSD appears.  
Main Menu  
MENU  
SET  
: Exit  
: Adjust (Decrease/Increase)  
: Enter  
: Select another sub-menu  
: Restart to select sub-menu  
Button Tip  
Sub-menus  
Menu Name  
Icons  
NOTE  
OSD (On Screen Display) menu languages on the monitor may differ from the manual.  
A11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
On Screen Display(OSD) Selection and Adjustment  
Main menu  
Sub menu  
Description  
PICTURE  
PICTURE  
RGB/DVI input  
To adjust the brightness of the screen.  
To adjust the contrast of the screen.  
BRIGHTNESS  
CONTRAST  
GAMMA  
Set your own gamma value. : -50/0/50  
On the monitor, high gamma values  
display whitish images and low gamma  
values display high contrast images.  
HDMI input  
You can set the offset level. If you select  
'HIGH', the screen will be bright and if you  
select ‘LOW’, the screen will be dark.  
(only for HDMI input)  
BLACK LEVEL  
* Offset? As the criteria for video signal, it is the  
darkest screen the monitor can show.  
MENU : Exit  
: Decrease  
: Increase  
SET : Select another sub-menu  
COLOR  
COLOR  
• sRGB: Set the screen color to fit the  
SRGB standard color  
PRESET  
specification.  
• 6500K: Slightly reddish white.  
• 9300K: Slightly bluish white.  
Set your own red color levels.  
Set your own green color levels.  
Set your own blue color levels.  
RED  
GREEN  
BLUE  
MENU : Exit  
: Decrease  
: Increase  
SET : Select another sub-menu  
A12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
On Screen Display(OSD) Selection and Adjustment  
Main menu  
Sub menu  
Description  
TRACKING  
TRACKING  
To move image left and right.  
To move image up and down.  
HORIZONTAL  
VERTICAL  
To minimize any vertical bars or  
stripes visible on the screen  
background.  
The horizontal screen size will also  
change.  
CLOCK  
PHASE  
To adjust the focus of the display.  
This item allows you to remove  
any horizontal noise and clear or  
sharpen the image of characters.  
MENU : Exit  
: Decrease  
To adjust the clearness of the  
screen.  
SHARPNESS  
: Increase  
SET : Select another sub-menu  
A13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
On Screen Display(OSD) Selection and Adjustment  
Main menu  
Sub menu  
Description  
SETUP  
SETUP  
To choose the language in which the  
control names are displayed.  
LANGUAGE  
OSD  
POSITION  
To adjust position of the OSD window  
on the screen.  
If the output of the video card is different  
the required specifications, the color  
level may deteriorate due to video  
signal distortion. Using this function, the  
signal level is adjusted to fit into the  
standard output level of the video card  
in order to provide the optimal image.  
Activate this function when white and  
black colors are present in the screen.  
(only for RGB/DVI input)  
WHITE  
BALANCE  
RGB  
RGB/DVI input  
RGB  
To select the range of output image for  
DTV timing in HDMI input.  
OVERSCAN  
HDMI input  
(only for HDMI input)  
Recommend overscan function to turn  
on when connect AV equipment.  
If you set ON, you enable the Response  
Time Control function.  
RTC  
If you set OFF, you disable the  
Response Time Control function.  
MENU : Exit  
: Adjust  
: Adjust  
Use this function to set the power  
indicator on the front side of the monitor  
to ON or OFF.  
POWER  
INDICATOR  
SET : Select another sub-menu  
If you set OFF, it will go off.  
If you set ON at any time, the power  
indicator will automatically be turned on.  
Restore all factory default settings except  
FACTORY  
RESET  
"LANGUAGE."  
Press the  
,
buttons to reset immediately.  
If this does not improve the screen image, restore the factory default settings.  
If necessary, perform the white balance function again. This function will be enabled only when  
the input signal is an analog signal.  
A14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
On Screen Display(OSD) Selection and Adjustment  
The OSD screen will appear when you touch the FUN button on the left bottom of the  
monitor.  
RGB/DVI input  
HDMI input  
VOLUME  
Main menu  
Sub menu  
Description  
EZ ZOOMING  
EZ Zoom lowers the display’s resolution in  
single-step increments. Depressing the button  
once lowers the resolution by one step; while a  
second button-press returns the resolution to  
the original display settings.  
*This function is operated only if the  
forteManager is installed to PC.  
*ForteManager is not supported in HDMI input.  
4:3 IN WIDE  
To select the image size of the screen.  
WIDE  
4:3  
WIDE : Switch to full screen mode according to input  
image signal.  
4 : 3 : Change the image signal ratio into 4:3.  
A15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
On Screen Display(OSD) Selection and Adjustment  
Main menu  
Sub menu  
Description  
To select the color of the screen.  
PHOTO EFFECT  
NORMAL :  
The PhotoEffect function is disabled.  
GAUSSIAN BLUR :  
This option is to add the effect to the screen that  
the dark and sharp image becomes brighter and  
more blurred.  
SEPIA :  
This option changes the screen to be Sepia tone.  
The Sepia tone is brown color tone.  
MONOCHROME :  
This option changed the screen to be Gray tone.  
The screen image is displayed with just white,  
black, gray colors.  
NORMAL  
SEPIA  
MONOCHROME  
GAUSSIAN BLUR  
To adjust the volume of headphone/Earphone.  
(only for HDMI input)  
VOLUME  
VOLUME  
SET  
VOLUME  
A16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
On Screen Display(OSD) Selection and Adjustment  
The OSD screen will appear when you touch the  
the monitor.  
button on the left bottom of  
Menu Name  
Icons  
Sub-menu Name  
Main menu  
Sub menu  
Description  
MOVIE  
Select this when you are watching a video or  
movie.  
RGB/DVI input  
INTERNET Select this when you are working on the  
document (Word etc.)  
HDMI input  
GAME  
Select this when you are playing a game.  
RGB/DVI input  
NORMAL Select this when you want to use the product in  
the most general using environment.  
HDMI input  
STANDARD  
Select this when you want to use the original  
standard video.  
* In the General (Standard) mode, the  
is turned off.  
A17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
On Screen Display(OSD) Selection and Adjustment  
Main menu  
Sub menu  
Description  
RGB/DVI input  
DEMO  
This is used for advertising in the store. The screen  
will be divided to show the standard mode on the  
left and video mode on the right so that the  
consumers can check the difference after applying  
the video mode.  
HDMI input  
SPORTS  
USER  
Select this when you watching general sports.  
You can manually adjust brightness, ACE or RCM  
(only for RGB/DVI input), HUE or SATURATION  
(only for HDMI input).  
You can save or restore the adjusted value even  
when using a different environment.  
...  
(Brightness) : Adjusts screen brightness.  
RGB/DVI input  
...  
ACE(Adaptive Clarity Enhancer) : Selects the clarity mode.  
Not applied  
Weak clarity and luminosity contrast.  
Strong clarity and luminosity contrast.  
...  
RCM(Real Color Management) : Selects the color mode.  
Not applied  
Green enhance  
Flesh tone  
HDMI input  
Color Enhance  
... HUE : Adjust the screen hue.  
... SATURATION : Adjust the screen saturation.  
Select the  
sub-menu using the AUTO/SET  
button and save the YES value using the  
buttons.  
,
MENU : Exit  
: Decrease  
: Increase  
: Select another sub-menu  
AUTO/SET  
A18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Check the following before calling for service.  
No image appears  
Is the power cord of  
the display connected? properly to the power outlet.  
Check and see if the power cord is connected  
Is the power indicator  
Press the Power button.  
light on?  
Adjust the brightness and the contrast.  
Is the power on and the  
power indicator red?  
Is the power indicator  
If the display is in power saving mode, try moving  
the mouse or pressing any key on the keyboard to  
bring up the screen.  
flicking?  
• Try to turn on the PC  
.
Do you see an "OUT  
OF RANGE" message  
on the screen?  
This message appears when the signal from the  
PC (video card) is out of horizontal or vertical  
frequency range of the display. See the  
'Specifications' section of this manual and  
configure your display again.  
Do you see a "CHECK  
SIGNAL CABLE"  
message on the  
screen?  
This message appears when the signal cable  
between your PC and your display is not  
connected. Check the signal cable and try again.  
Do you see a "OSD LOCKED" message on the screen?  
Do you see “OSD  
LOCKED” when you  
push MENU button?  
• You can secure the current control settings,  
so that they cannot be inadvertently changed.  
You can unlock the OSD controls at any time  
by pushing the MENU button for several  
seconds: the message  
“OSD UNLOCKED” will appear.  
A19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Display image is incorrect  
Display Position is  
Press the AUTO/SET button to automatically  
adjust your display image to the ideal setting.  
If the results are unsatisfactory, adjust the image  
position using the H position and V position icon  
in the on screen display.  
incorrect.  
Press the AUTO/SET button to automatically  
adjust your display image to the ideal setting.  
If the results are unsatisfactory, decrease the  
vertical bars or stripes using the CLOCK icon in  
the on screen display.  
On the screen  
background, vertical  
bars or stripes are  
visible.  
Press the AUTO/SET button to automatically  
adjust your display image to the ideal setting.  
If the results are unsatisfactory, decrease the  
horizontal bars using the PHASE icon in the on  
screen display.  
Check Control Panel --> Display --> Settings  
and adjust the display to the recommended  
resolution or adjust the display image to the ideal  
setting. Set the color setting higher than 24 bits  
(true color).  
Any horizontal noise  
appearing in any  
image or characters  
are not clearly  
portrayed.  
Important  
Check Control Panel --> Display --> Settings and see if the frequency or the  
resolution were changed. If yes, readjust the video card to the recommend  
resolution.  
Reasons for Recommending Optimal Resolution : The aspect ratio is 16:10.  
If the input resolution is not 16:10 (for instance, 16:9, 5:4, 4:3), you might  
encounter problems such as blurred letters, blurry screen, cut-off screen display or  
tilted screen.  
The setting method can differ by computer and O/S (Operation System),  
and resolution mentioned above may not be supported by the video card  
performance. In this case, please ask to the computer or the video card  
manufacturer  
.
When HDMI interleaved signal (1920 x 1080i) input, static picture will be shaking,  
however moveable picture is not. So the recommend resolution is 1920 x 1080 @ 60Hz.  
A20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Display image is incorrect  
The screen color is  
Check if the signal cable is properly connected  
and use a screwdriver to fasten if necessary.  
Make sure the video card is properly inserted in  
the slot.  
Set the color setting higher than 24 bits (true color)  
at Control Panel - Settings.  
mono or abnormal.  
The screen blinks.  
Check if the screen is set to interlace mode and if  
yes, change it to the recommend resolution.  
Have you installed the display driver?  
Have you installed the  
display driver?  
Be sure to install the display driver from the display  
driver CD (or diskette) that comes with your  
display. Or, you can also download the driver from  
Make sure to check if the video card supports  
Plug&Play function.  
Do you see an  
"Unrecognized monitor,  
Plug&Play (VESA DDC)  
monitor found"  
message?  
A21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
Display  
21.5 inches (54.6 cm) Flat Panel Active matrix-TFT LCD  
Anti-Glare coating  
Visible diagonal size: 54.6 cm  
0.248*0.248 mm pixel pitch  
Horizontal Freq.  
Analog : 30 - 83 kHz (Automatic)  
Digital : 30 - 83 kHz (Automatic)  
Analog,Digital: 56 - 75 Hz (Automatic)  
Separate TTL, Positive/Negative  
SOG (Sync On Green)  
Sync Input  
Vertical Freq.  
Input Form  
Digital (HDCP)  
Signal Input  
15 pin D-Sub Connector  
Video Input  
DVI - D connector (Digital)  
Input Form  
Max  
RGB Analog (0.7 Vp-p/ 75 ohm), Digital, HDMI  
Analog : VESA 1920 x 1080 @60 Hz  
Digital : VESA 1920 x 1080 @60 Hz  
VESA 1920 x 1080 @60 Hz  
Resolution  
Plug&Play  
Recommend  
DDC 2B (Digital, HDMI), DDC 2AB (Analog)  
:
39 W(Typ.)  
1 W  
1 W  
Power  
Consumption  
On Mode  
Sleep Mode  
Off Mode  
With Stand  
Without Stand  
Dimensions  
&Weight  
Width 51.90 cm / 20.43 inches 51.90 cm / 20.43 inches  
Height 38.73 cm / 15.24 inches 33.08 cm / 13.02 inches  
Depth 19.32 cm / 7.61 inches  
6.34 cm / 2.50 inches  
Net  
Tilt  
4.2 kg (9.26 lbs)  
-5˚~17˚  
Tilt Range  
AC 100-240V~ 50/60Hz 1.0A  
Power Input  
Operating Conditions  
Environmental  
Conditions  
Temperature 10˚C to 35 ˚C  
Humidity  
10 % to 80 % non-Condensing  
Storage Conditions  
Temperature -20˚C to 60 ˚C  
Humidity  
5 % to 90 % non-Condensing  
Stand Base  
Signal cable  
Power cord  
Attached( ), Detached ( O )  
Attached( ), Detached ( O )  
Wall-outlet type or PC-outlet type  
NOTE  
Information in this document is subject to change without notice.  
A22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
Preset Modes (Resolution)  
RGB/DVI Timing  
Display Modes (Resolution)  
Horizontal Freq. (kHz)  
Vertical Freq. (Hz)  
1
2
31.468  
31.469  
37.500  
37.879  
46.875  
48.363  
60.123  
67.500  
63.981  
79.976  
65.290  
67.500  
720 x 400  
640 x 480  
70  
60  
75  
60  
75  
60  
75  
75  
60  
75  
60  
60  
3
640 x 480  
4
800 x 600  
800 x 600  
5
6
1024 x 768  
1024 x 768  
1152 x 864  
1280 x 1024  
1280 x 1024  
1680 x 1050  
1920 x 1080  
7
8
9
10  
11  
*12  
* Recommend Mode  
HDMI Timing  
Display Modes (Resolution)  
Horizontal Freq. (kHz)  
Vertical Freq. (Hz)  
1
2
3
4
5
6
7
8
31.50  
31.25  
37.50  
45.00  
28.12  
33.75  
56.25  
67.50  
480P  
576P  
720P  
720P  
1080i  
1080i  
1080P  
1080P  
60  
50  
50  
60  
50  
60  
50  
60  
Indicator  
LED Color  
MODE  
red  
flicker  
Off  
On Mode  
Sleep Mode  
Off Mode  
A23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Digitally yours  
Download from Www.Somanuals.com. All Manuals Search And Download.  

La Crosse Technology Clock WT 3143H User Manual
Learning Resources Baby Toy Ler 2574 User Manual
Lennox Hearth Stove SS210 User Manual
Lenovo Computer Drive 42T7993 User Manual
Lenovo Laptop 24384KU User Manual
Linear Satellite Radio GT 31 User Manual
Loewe Work Light Xelos 32 LED User Manual
Mackie Stereo Amplifier SP1200 User Manual
Makita Trimmer JS1602 User Manual
McCulloch Lawn Mower 532 43 45 03 User Manual