Installation Guide
Web Smart Managed
10/100 Fast Ethernet Switches
with VLAN Support
KS-115FM-V
KS-117FM-V
DOC.030430-KS115FM-V-KS117FM-V-K
Download from Www.Somanuals.com. All Manuals Search And Download.
The information contained in this document is subject to change without prior notice.
Copyright (C) All Rights Reserved.
TRADEMARKS
Ethernet is a registered trademark of Xerox Corp.
This device complies with Class A Part 15 the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received including the interference that may cause.
CISPR A COMPLIANCE:
This device complies with EMC directive of the European Community and meets or exceeds the follow-
ing technical standard.
EN 55022 - Limits and Methods of Measurement of Radio Interference Characteristics of Information
Technology Equipment. This device complies with CISPR Class A.
WARNING: This is a Class A product. In a domestic environment this product may cause radio inter-
ference in which case the user may be required to take adequate measures.
CE NOTICE
Marking by the symbol
indicates compliance of this equipment to the EMC directive of the
European Community. Such marking is indicative that this equipment meets or exceeds the following
technical standards:
EN 55022: Limits and Methods of Measurement of Radio Interference characteristics of Information
Technology Equipment.
EN 50082/1:Generic Immunity Standard -Part 1: Domestic Commercial and Light Industry.
EN 60555-2: Disturbances in supply systems caused by household appliances and similar electrical equip-
ment - Part 2: Harmonics.
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
1. Introduction ..................................................................5
1.1 Features ........................................................................................... 6
1.2 Specifications .................................................................................. 7
1.3 FX Port Optical Specifications ......................................................... 8
1.4 Management Specifications ............................................................ 9
2. Installing the Switches ...............................................10
2.1 Unpacking ..................................................................................... 10
2.2 Supply the Power .......................................................................... 10
2.3 Port Configuration ......................................................................... 11
2.4 VLAN Function ............................................................................. 12
2.5 DHCP and IP Configuration........................................................... 15
2.6 Push Button IP SW ....................................................................... 15
2.7 Making UTP Connections ............................................................. 16
2.8 Making Fiber Connection.............................................................. 17
2.9 LED Indications ............................................................................. 18
3. Web Management ......................................................19
3.1 Web Browser ................................................................................. 19
3.2 Port Setup ...................................................................................... 22
3.3 IP Setup ......................................................................................... 23
3.4 VLAN Setup .................................................................................. 24
3.4.1 Port-based VLAN ....................................................................... 25
3.4.2802.1QVLAN .............................................................................. 27
.5 Password Setup ............................................................................... 30
3.6 Restore Default .............................................................................. 31
3.7 ReBoot Device ............................................................................... 32
3.8 About ............................................................................................ 33
Appendix: Factory Default Values.................................34
Appendix: Effective Time of Setting Changes ..............34
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
This guide describes the specifications and installation instructions for
the following two managed 10/100 switch series:
KS-115FM-V series
•
•
•
•
Four 10/100BASE-TX auto-negotiation TP switched ports
One 100BASE-FX Fiber switch port
Web-based device management support
Compact Fast Ethernet switch
KS-117FM-V series
•
•
•
•
Six 10/100BASE-TX auto-negotiation TP switched ports
One 100BASE-FX Fiber switch port
Web-based device management support
Compact Fast Ethernet switch
-5-
Download from Www.Somanuals.com. All Manuals Search And Download.
1.1 Features
•
The 10/100BASE-TX switched ports support:
-
-
-
-
Auto speed sensing for 100Mbps or 10Mbps connection
Auto configuration for connected auto-negotiation devices
Full-duplex or half-duplex operation
Port configuration can be changed via web management interface
•
•
The 100BASE-FX switched port supports:
-
-
-
100Mbps full duplex connection
Variety of fiber connectors such as ST, SC, MT-RJ, LC and VF-45
Multimode and single mode fiber cables (model dependent)
Provide the following switch functions:
-
-
-
-
-
-
-
Self learning for active MAC addresses up to 2K entries
Store and forward switching that only good packets are forwarded
Forwarding and filtering at full wire speed
Flow control for traffic congestion
Broadcast packet storm protection
Port-based VLAN function
IEEE 802.1Q VLAN function
•
Provide the following management functions:
-
-
-
-
-
-
-
-
Web-base interface for easy management
DHCP support for IP configuration
Static IP configuration if DHCP is not available
Port status and configuration
VLAN configuration
Security check for management login
Restore factory default settings
Remote boot
•
Comprehensive LED indicators
-6-
Download from Www.Somanuals.com. All Manuals Search And Download.
1.2 Specifications
Figure : Major Components on Panels (Ex. KS-117FM-V)
KS-115FMP1-P4 Port 1 ~ Port 4 Twisted-pair switched ports (TP ports)
KS-117FMP1-P6 Port 1 ~ Port 6 Twisted-pair switched ports (TP ports)
TP Port
IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX std.
Shielded RJ-45 jacks with Auto MDI-X detection
Auto-negotiation capable
Speed for 10Mbps or 100Mbps
Full-duplex or half-duplex support
FX Port
IEEE 802.3u 100BASE-FX compliant
Fixed 100Mbps Full-duplex operation
Flow control
Cables
IEEE 802.3x pause packet for full duplex operation
Back pressure for half duplex operation
10BASE-T Cat. 3, 4, 5 or higher (100 meters max.)
100BASE-TX Cat. 5, 5e or higher (100 meters max.)
100BASE-FX multimode or single mode fiber cable
LED indicators Power status
TP ports : Speed, Link/Activity, Duplex/Collision status
FX port : Link/Activity, Duplex/Collision status
Filtering rate
14,880 pps for Ethernet (10BASE-T)
148,800 pps for Fast Ethernet (100BASE-TX)
Forwarding rate 14,880 pps for Ethernet (10BASE-T)
148,800 pps for Fast Ethernet (100BASE-TX)
-7-
Download from Www.Somanuals.com. All Manuals Search And Download.
Filteringaddress Multicast/Broadcast/Unicast address
MAC address
Aging time
2K entries
300 seconds
Priority levels 2 outgoing priority queues (Ratio: High/Low = 4/1 )
VLANmode 1. Port-based VLAN 2. 802.1Q VLAN (Tag-based)
VLAN groups 16 groups (Group 0 ~ 15)
Port PVID Full 12-bit VID, per port setting
Port Tag Mode Tag/Untag mode, per port setting
Environment
Temperature 0oC to 40oC
Relative humidity 10% to 90% non-condensing
Dimensions
144mmx100mmx26mm(WxDxH)
5.67 x 3.94 x 1.02 inch
DC IN Power
DC IN Jack
Rating +7.5V min. 1A
D6.3mm
D2.0mm
Operatingvoltage +6.5 ~ +12.5VDC (Device DC Input)
Power Consumption 7W max. (with power adapter)
1.3 FX Port Optical Specifications
Model Ext. Connector Wavelength Tx optical powerRx sensitivity
-VT
-VC
-VJM
-VVM
-VL
MM*1 ST
MM SC
MM MT-RJ 1310nm
MM VF-45 1310nm
1310nm
1310nm
-20 ~ -14dBm
-20 ~ -14dBm
-20 ~ -14dBm
-20 ~ -14dBm
-19 ~ -14dBm
-15 ~ - 8dBm
-31dBm
-31dBm
-31dBm
-31dBm
-34dBm
-31dBm
MM LC
1310nm
1310nm
-VSA2
SM*2 SC
*1 : Multimode fiber
*2 : Single Mode fiber
-8-
Download from Www.Somanuals.com. All Manuals Search And Download.
1.4 Management Specifications
Interface
In-band web browser for IE4.0 and Netscape4.x
Ping command, ARP command
Protocols
IP Setting
IPv4, ARP, ICMP,UDP, TCP, DHCP client, Http server
DHCP dynamic IP mode (default mode)
Static IP mode (default : 192.168.0.2)
DHCP
DHCP client ID = Device modelname + MAC address
Security
Login password checking
Password setting (default : 123)
Port
All ports : port status monitoring
Monitoring Link, Speed, Duplex, Flow control status
Port
Control
Per TP port configuration settings
Auto-negotiation function : enable, disable
Speed : 100M, 10M
Duplex : full, half
VLAN
VLAN mode selection: Port-based, 802.1Q (Tag-based)
Port-based 16 VLAN groups
VLAN
Member ports setting for each group
PVID (12-bit VLAN ID value) setting for each port
802.1Q
VLAN
16 VLAN groups
Member ports setting for each group
PVID (12-bit VLAN ID value) setting for each port
Tag/Untag mode setting for each port
Restore
Default
Restore factory default settings
Refer to Appendix for factory default settings
Reboot
In-band remote boot the switch
-9-
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installing the Switches
2.1 Unpacking
Check to see that you have everything before you start the installation.
•
•
•
•
Installation guide
The switch unit
Rubber magnet stand
One AC power adapter for the unit
2.2 Supply the Power
Checking AC Power
Before you begin the installation, check the AC voltage of your area. The
AC power adapter which is used to supply the DC power for the unit should
have the AC voltage matching the commercial power voltage in your area.
The specifications of the AC power adapter are:
•
•
AC input power:
DC output power: Rating +7.5V VDC min. 1.0A
AC power voltage of your area
•
DC plug type:
DC IN Jack
The DC power jack for the AC power adapter is located on the rear of the
switch. Refer to section 1.2 drawing.
Installing the Switch
1. Install the switch with the AC power adapter provided.
-10-
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Connect the power adapter cable to the switch before connecting
the adapter to the AC outlet.
2.3 Port Configuration
The switches provide port configuration function through the manage-
ment interface. The setting options are shown as follows:
Port Type
TP PORTS
FX PORT
Auto-negotiation Enable/Disable Not allowed
Speed options
Duplex options
100M / 10M
Full / Half
Not allowed (fixed 100M)
Not allowed (fixed Full)
When auto-negotiation is enabled, the speed and duplex settings be-
come the port highest ability used for auto-negotiation process. The
final configurations used with the connected device may be different
from the settings after negotiation between two devices. As auto-nego-
tiation is disabled, the speed and duplex settings are the forced operating
configuration for the connection.
The real time port status for each port connection can be monitored
through the management interface. The status are:
Link
Physical link status
Speed
Duplex
Connection speed used
Duplex mode used
Flow Control
Flow control status after negotiation
-11-
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4 VLAN Function
The switches support two VLAN modes. One is Port-based VLAN and
the other is 802.1Q VLAN.
The following configuration are supported:
1. VLAN Mode : Port-based mode or 802.1Q mode
2. VLAN mapping table setup : member ports setup for each group
3. Per port PVID setup : PVID setting, Tag mode setting
Port-basedVLANMode
1. This mode supports 16 VLAN groups, Group 0 ~ Group 15.
2. Packet forwarding is performed only among the member ports in
same group.
3. Every packet, tagged or untagged, is forwarded from input port to
output port transparently without any packet modification.
4. Per port PVID setting is used for index to VLAN Group table. When
a packet is received, the associated PVID setting of the input port is
used to map to one VLAN group in VLAN group table. The mapping
index is retrieved from the least 4 bits (bit 3~0) of the PVID value.
5. Tag mode settings are preset with untagged mode for all ports and
not changeable in Port-based VLAN mode.
6. VLAN tag in every input tagged packet is ignored.
Note:
To provide more flexibility for LAN administrator in performing web man-
agement task, the internal MNG port which connects to the built-in Http
server is disclosed for PVID configuration. The MNG port is also config-
ured as the member port for all VLAN groups and untag port perma-
nently.
-12-
Download from Www.Somanuals.com. All Manuals Search And Download.
802.1Q VLAN Mode
1. This mode supports 16 VLAN groups, Group 0 ~ Group 15.
2. When an untagged packet is received, the associated PVID setting
of the input port is used to map to one VLAN group in VLAN group
table. The mapping index is retrieved from the least 4 bits (bit 3~0) of
the PVID value.
3. When a tagged packet is received, the VLAN ID value of the
received packet is used to map to one VLAN group in VLAN group
table. The mapping index is retrieved from the least 4 bits (bit 3~0) of
the VLAN ID value.
4. Packet forwarding is performed only among the member ports in
same group. If the input port of the received packet is not the
member port of the mapped group, the packet will be dropped.
5. For outbound, Tag mode of the output port is applied as follows:
Received untagged packet output to:
Tag port :
The packet is inserted with PVID of the input port
as VLAN ID and new CRC.
Untag port : The packet is forwarded with no change.
Received tagged packet output to:
Tag port :
The packet is forwarded with no change.
Untag port : The VID of the packet is removed and forwarded
with new CRC.
Note:
When VLAN mode is set from 802.1Q mode to Port-based mode, all ports
are set to Untag ports automatically.
-13-
Download from Www.Somanuals.com. All Manuals Search And Download.
Summary of VLAN Group Lookup (Group Mapping Index)
Input Packet Type Port-basedVLANMode 802.1Q VLAN Mode
Untagged packet
Tagged packet
PVIDbit3-0ofinputport PVIDbit3-0ofinputport
PVIDbit3-0ofinputport VIDbit3-0ofthepacket
Factory Default Settings
VLAN Mode
VLAN Group 0
VLAN Group 1
Port-based mode
MNG port only (No user port)
All user ports and MNG port
VLAN Group 2~15 No user port (MNG port only)
PVID
1 for all ports and MNG port
Tag Mode
Untagged for all ports and MNG port
-14-
Download from Www.Somanuals.com. All Manuals Search And Download.
2.5 DHCP and IP Configuration
Each switch must be designated an IP address before it can be managed
from web browser. Basically, the switches provide two methods for IP
configuration:
1. DHCPmode
The switch requests a dynamic IP address from the first discovered
DHCP server in the network when boot up. In general, the assigned
IP can be monitored in the client list on the DHCP server. The model
name and MAC address of the switch is referred as the DHCP client
ID. If no DHCP server is discovered after a retry period for about 40
seconds, the pre-configured static IP is used automatically.
2. Static IP mode
One pre-configured IP address is used when DHCP mode is disabled
or when DHCP mode is enabled and no DHCP server is available.
The static IP can be configured through management interface. Each
switch comes with one identical factory default IP upon device
reception.
It is important to record the MAC address and location where it is in-
stalled for each switch. It would help in tracing the IP and device map-
ping.
2.6 Push Button IP SW
One push button IP SW located on rear panel is used to disable DHCP mode
and restore static IP back to factory default value. It is useful when you do
not recall your static IP setting and DHCP solution is not available.
To make the function work, push the SW and keep for at least 5 seconds
when the switch is powered on to be boot up.
Download from Www.Somanuals.com. All Manuals Search And Download.
2.7 Making UTP Connections
TP Port Configuration
Use management function to set the required TP port configuration. It is
recommended to set the highest ability for the TP ports as follows:
Auto-negotiation = enabled
Speed = 100M
Duplex = Full
This is appropriate to support connection to almost every Ethernet de-
vices including those which are not auto-negotiation capable.
Cables
Depending on the connection speed, use the appropriate UTP cables for
the connections as follows:
Speed
100M
10M
Cables used
Cat. 5, 5e, or higher grade
Cat. 3, 4, 5, 5e, or higher grade 100 meters
Distance
100 meters
Auto-MDI-XFunction
An Auto-MDI-X function will automatically detect if a crossover is re-
quired and make the swap of Tx pair and Rx pair internally. With this
function, straight-through cable can be used for any connection. MDI to
MDI-X connection rule is not necessary anymore. In the switches, all TP
ports are equipped with this function. You can use just straight-through
type of cables for all your connections.
-16-
Download from Www.Somanuals.com. All Manuals Search And Download.
2.8 Making Fiber Connection
For different fiber connections, several alternative models can be
selected for different fiber connections as follows:
ModelExt. Connector Cable Max. Distance*
-T
-C
-JM
-VM
-L
ST
SC
MM
MM
2
2
2
2
2
Km
Km
Km
Km
Km
MT-RJ MM
VF-45
LC
MM
MM
SM
-SA2
SC
20 Km
*: The maximum distance connecting to a full duplex device
The recommended multimode fiber is 62.5/125mm and 9/125mm for single
mode fiber. The following figure illustrates a connection example be-
tween two SC fiber ports:
-17-
Download from Www.Somanuals.com. All Manuals Search And Download.
2.9 LED Indications
Functions
POWER:
100/10 :
indicates the status of the power supplied to the switch.
indicates the connection speed between the TP port
and the associated connected device.
LINK/Act. : indicates the port link and activity status
FDX/Col. : indicates the duplex mode and collision occurrences
The following table lists the LED states and the indications:
LED
State
OFF
ON
OFF
ON
Indication
POWER
POWER
100/10
100/10
No power is supplied to the device.
Power is supplied to the device.
10Mbps is used.
100Mbps is used.
LINK/Act. OFF
LINK/Act. ON
LINK/Act. Blink
No active cable link
An active link is established.
Tx/Rx activities
FDX/Col
FDX/Col
FDX/Col
ON
OFF
Blink
Full duplex is used.
Half duplex is used.
Half duplex and collision occurrences
-18-
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Web Management
3.1 Web Browser
The system features an http server which can serve the management
requests coming from any web browser software over internet or intranet
network.
Web Browser
Compatible web browser software with JAVA support
Microsoft Internet Explorer 4.0 or later
Netscape Communicator 4.x or later
Start connection
Before the switch can be managed from a web browser software, the
switch IP address is required. Consult your LAN administrator if it is not
available. Start your browser software and enter the IP address of the
switch to which you want to connect. The IP address is used as URL for
the browser software to search the device.
URL:http://xxx.xxx.xxx.xxx/
Factory default IP address : 192.168.0.2
When browser software connects to the switch unit successfully, a Lo-
gin screen is provided for you to login to the device as follows:
-19-
Download from Www.Somanuals.com. All Manuals Search And Download.
Enter your password and click [OK] to login into the switch. The switch
comes with factory default password : 123.
-20-
Download from Www.Somanuals.com. All Manuals Search And Download.
The web page is shown as follows when a successful login is performed:
The left side shows the switch model and menu list. The list includes :
[Port Setup]
[IP Setup]
: shows port status and port configuration setup
: setup IP mode and related settings
[VLAN Setup] : setup VLAN related settings
[Password Setup] : change password
[Restore Default]: restore factory default settings for the switch
[ReBoot Device] : remote boot the switch
[About]
: shows management software information
-21-
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2 Port Setup
The middle part of previous figure shows all port status of the connected
switch. The right side shows port configuration setup page.
Port Status
Port Status page displays the current port status. The status are:
Port
Port number (FX : FX port)
Link
Speed
Duplex
Port link status, Up = link up, Down = link down
Port speed, 100M = 100Mbps, 10M = 10Mbps
Duplex mode used, Full = full-duplex, Half = half-duplex
Flow Control Flow control status, enabled, disabled
Note:
The switch is featured with flow control enabled for all ports. However,
the flow control may be disabled after auto negotiation with the con-
nected device, if the connected device does not have flow control ability.
Port Setup
This page is used to set the port configuration for each port. As auto-
negotiation function is enabled, speed and duplex settings specify the
highest port ability for negotiation process between the switch and the
auto-negotiation capable link partner. When auto-negotiation function
is disabled, speed and duplex settings specify the forced port configura-
tion for the connection. Setup options are:
Auto-negotiation
Speed
Duplex
Enabled, disabled
100M = 100Mbps, 10M = 10Mbps
Full = full-duplex, Half = half-duplex
It is recommended to set auto-negotiation enabled in most of cases and
set it disabled only when connecting to an auto-negotiation incapable
full-duplex device.
[Apply] Click to make the setup effective immediately
-22-
Download from Www.Somanuals.com. All Manuals Search And Download.
3.3 IP Setup
This page includes the following functions:
IP Status
IP Setup
Display information of current IP used
If the current IP address is labeled (DHCP), it means the
IP is assigned by DHCP server.
Set static IP address to be used when DHCP is disabled
or when no DHCP server is available.
DHCP Setup Enable to get and use dynamic IP address assigned by
DHCP server. Disable to use Static IP setting.
Any change or click [Apply] do not affect current management connec-
tion. They will be effective for next bootup.
-23-
Download from Www.Somanuals.com. All Manuals Search And Download.
3.4 VLAN Setup
VLAN Mode Select
Port-based VLAN : Port-based VLAN
802.1Q base VLAN : IEEE 802.1Q Tag-based VLAN
Click [Apply] to make change effective immediately.
Note:
1. Both modes use same group member port settings and Port PVID
settings. When selecting Port-based VLAN, all ports are set to
Untag ports automatically.
2. Under Port-based VLAN mode, all packets are forwarded transpar-
ently with no packet modification.
-24-
Download from Www.Somanuals.com. All Manuals Search And Download.
3.4.1 Port-based VLAN
Click [VLAN Mapping Table]
This page is used to setup member ports for each VLAN group. Total of
16 VLAN groups are supported.
The steps to configure the member ports are:
1. Select Group number : 0 ~ 15.
2. Set [Yes] on the selected port to include it into the member port list.
Note:
One port can belong to more than one VLAN groups. VLAN group table
mapping index is based on the least four bits (bit 3 ~ bit 0) of the PVID of
the input port.
-25-
Download from Www.Somanuals.com. All Manuals Search And Download.
Click [Port PVID Setting]
This page is used to setup PVID and Tag mode for each port as follows:
PVID : The setting value is used for VLAN group lookup index. When a
packet is received, the least four bits (bit 3~bit 0) of the PVID setting of
the input port is used as the index mapping to one VLAN group. The
mapped group is used for packet forwarding operation. The valid value
range is 1 ~ 4095.
Refer to section 2.4 for more information about the MNG port.
Tag Mode : Tag mode setting of each port is preset to Untag mode auto-
matically and they are not changeable under Port-based VLAN mode.
-26-
Download from Www.Somanuals.com. All Manuals Search And Download.
3.4.2 802.1Q VLAN
Click [VLAN Mapping Table]
This page is used to setup member ports for each VLAN group. Total of
16 VLAN groups are supported. Actually, the table are shared by Port-
based VLAN mode and 802.1Q VLAN mode.
The steps to configure the member ports are:
1. Select Group number : 0 ~ 15.
2. Set [Yes] on the selected port to include it into the member port list.
802.1Q VLAN group mapping is dependent on the received packet type:
Untagged packet - Use the least four bits of PVID value of the input port
Tagged packet - Use the least four bits of the VID value of the packet
-27-
Download from Www.Somanuals.com. All Manuals Search And Download.
Click [Port PVID Setting]
This page is used to setup PVID and Tag mode for each port as follows:
PVID : The valid value range is 1 ~ 4095. The setting value is used for the
following purposes:
1. It is used as VLAN group lookup index when an untagged packet is
received. The least four bits (bit 3~bit 0) of the PVID setting of the
input port is used for mapping to one VLAN group.
2. It is used to be inserted into the packet as VID when an untagged
packet is received and forwarded to a Tag port.
-28-
Download from Www.Somanuals.com. All Manuals Search And Download.
Tag Mode : Setting for each port to be Tag port or Untag port for out-
bound.
Tag port - All output packets are tagged.
Untag port - All output packets are untagged.
Depending on the received packet type, the rules are applied as follows:
Received untagged packet output to:
Tag port :
The packet is inserted with PVID of the input port
as VLAN ID and new CRC.
Untag port : The packet is forwarded with no change.
Received tagged packet output to:
Tag port :
The packet is forwarded with no change.
Untag port : The VID of the packet is removed and forwarded
with new CRC.
Note:
1. When VLAN mode is switched from 802.1Q mode to Port-based
mode, the Tag mode settings for all ports are preset to Untag
automatically.
2. When VLAN mode is changed, current group member ports settings
and per port PVID settings are applied to new VLAN mode.
-29-
Download from Www.Somanuals.com. All Manuals Search And Download.
.5 Password Setup
Password is used for checking authority for accessing the switch. To
change password setting, enter your new password and reconfirm the
input again.
Click [Apply] to apply the new password immediately.
-30-
Download from Www.Somanuals.com. All Manuals Search And Download.
3.6 Restore Default
This command is used to restore all settings back to factory default
values. Click [Restore] to apply immediately. Refer to Appendix for fac-
tory default values.
-31-
Download from Www.Somanuals.com. All Manuals Search And Download.
3.7 ReBoot Device
The command is used to reboot the switch remotely over the network.
Normally, it is used after IP settings are changed.
-32-
Download from Www.Somanuals.com. All Manuals Search And Download.
3.8 About
About page shows switch model name and software version.
-33-
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix: Factory Default Values
Settings
Factory Default Values
Enabled
192.168.0.2
DHCP mode
Static IP address
Netmask
255.255.255.0
Default gateway IP 192.168.0.1
Login password
TP ports
TP port speed
TP port duplex
VLAN mode
123
Auto-negotiation enabled
100M (the highest ability)
Full duplex (the highest ability)
Port-based VLAN enabled
802.1Q VLAN disabled
VLAN group table Group 0 - MNG port only
Group 1 - all user ports and MNG port
Group 2~15 - MNG port only
1 for all ports
Untag for all ports
Port PVID
Tag mode
Appendix: Effective Time of Setting Changes
Settings
DHCP Mode
Effective Time of Changes
Next boot and permanently
Next boot and permanently
Immediately and permanently
Immediately and permanently
Immediately and permanently
Immediately and permanently
Immediately and permanently
Immediately and permanently
Static IP Setup
Password Setup
TP Ports Setup
VLAN Mode
VLAN mapping table
Port PVID setup
Port Tag mode Setup
-34-
Download from Www.Somanuals.com. All Manuals Search And Download.
|