Legacy Car Audio Car Stereo System LDVD84 User Manual

LDVD 84  
OWNER's MANUAL  
Mobile Video System  
DVD/VCD/CD/MP3 PLAYER WITH  
MANUALLY TUNED SYNTHESIZER STEREO RADIO  
Region Management Information  
Region Management Information:  
This DVD Player is designed and  
manufactured to respond to the Region  
Management Information that is recorded  
on a DVD disc. If the Region number  
described on the DVD disc does not  
correspond to the Region number of this  
DVD Player, this DVD Player cannot play  
this disc.  
CAUTION:  
THIS DVD PLAYER IS A CLASS I  
LASER PRODUCT. HOWEVER THIS  
DVD PLAYER USES A  
VISIBLE/INVISIBLE LASER BEAM  
WHICH COULD CAUSE HAZARDOUS  
RADIATION EXPOSURE IF DIRECTED.  
BE SURE TO OPERATE THE  
DVD PLAYER CORRECTLY AS  
INSTRUCTED.  
USE OF CONTROLS OR  
ADJUSTMENTSORPERFORMANCEOF  
PROCEDURES OTHER THAN THOSE  
SPECIFIED HEREIN MAY RESULT IN  
HAZARDOUS RADIATION EXPOSURE.  
DO NOT OPEN COVERSAND - DO NOT  
REPAIRYOURSELF. REFERSERVICING  
TO QUALIFIED PERSONNEL.  
WARNING:  
TO REDUCE THE RISK OF FIRE OR  
ELECTRIC SHOCK, DO NOTEXPOSE  
THIS EQUIPMENT TO RAIN OR  
MOISTURE.  
TO REDUCE THE RISK OF FIRE OR  
ELECTRIC SHOCK,ANDANNOYING  
INTERFERENCE, USE ONLY THE  
RECOMMENDED ACCESSORIES.  
THIS DEVICE IS INTENDED FOR  
CONTINUOUS OPERATION.  
This product incorporates copyright  
protection technology that is protected  
by method claims of certain U.S. patents  
and other intellectual property rights  
owned by Macrovision Corporation and  
other rights owners. Use of this  
copyright protection technology must be  
authorized by Macrovision Corporation,  
and is intended for home and other  
limited viewing uses only unless  
otherwise authorized by Macrovision  
Corporation. Reverse engineering or  
disassembly is prohibited.  
3
Disc formats supported by this player  
DVD  
Note these scratches are not an  
indication of any problem with the player.  
VID EO  
12 cm disc  
(Single-sided disc only)  
Video CD  
12 cm disc  
CD  
12 cm disc  
MP3  
12 cm disc  
Discs which cannot be played with this  
player  
DVD-ROM  
DVD-R/DVD-RAM  
CDV  
CD-G  
Handling and Cleaning  
Dirt, dust, scratches and warping disc  
will cause misoperation.  
Do not place stickers or make  
scratches on discs.  
Preparing New Discs with Rough Spots  
A new disc may have rough edges on its  
inside and outside edges. If a disc with  
rough edges is used, the proper setting  
will not be performed and the player will  
not play the disc. Therefore, remove the  
rough edges in advance by using a ball  
point pen or pencil as shown on the right.  
To remove the rough edges, press the  
side of the pen or pencil against the  
inside and outside edges of the disc.  
Do not warp discs.  
A disc should always be kept in its  
case when not in use to prevent from  
damaging.  
Do not place discs in the following  
places:  
1.Direct sunlight  
2.Dirty, dusty and damp areas  
3.Near car heaters  
4.On the seats or dashboard  
Disc Cleaning  
Use a dry soft cloth to wipe the surface.  
If the disc is quite dirty, use a soft cloth  
slightly moistured with isopropyl (rubbing)  
alcohol. Never use solvents such as  
benzine, thinner or conventional record  
cleaners as they may mar the surface of  
the disc.  
Note:  
Adisc may become somewhat scratched  
(although not enough to make it  
unusable) depending on your handle it  
and conditions in the usage environment.  
4
Choose the mounting location where the unit will not interfere with the normal  
driving function of the driver.  
Before finally installing the unit, connect the wiring temporarily and make sure it is  
all connected up properly and the unit and the system work properly.  
Use only the parts included with the unit to ensure proper installation. The use of  
unauthorized parts can cause malfunctions.  
Consult with your nearest dealer if installation requires the drilling of holes or other  
modifications of the vehicle.  
'
Install the unit where it does not get in the driver s way and cannot injure the  
passenger if there is a sudden stop, like an emergency stop.  
If installation angle exceeds 30 from horizontal, the unit might not give its optimum  
performance.  
Avoid installing the unit where it would be subject to high temperature, such as from  
direct sunlight, or from hot air, from the heater, or where it would be subject to dust,  
dirt or excessive vibration.  
This unit can be properly installed either from "Front"(conventional DIN Front-mount)  
or "Rear"(DIN Rear-mount installation, utilizing threaded screw holes at the sides of  
the unit chassis). For details, refer to the following illustrated installation methods.  
30  
5
DASH BOARD  
METAL MOUNTING STRAP  
CONSOLE  
HEX NUT  
SPRING WASHER  
PLAIN WASHER  
PLAIN WASHER  
TAPPING SCREW  
SLIDE BRACKET HOUSING  
HEX BOLT  
6
HOW TO REMOVE AND INSTALL THE FRONT PANEL  
1.Press the release button and pull-off the front panel.  
Keep front panel into the case.  
2.To install the front panel, insert the panel into the housing and make sure the panel  
is properly installed, otherwise, abnormalities occurs on the display or some keys will  
not function properly.  
REMOVING THE FRONT PANEL  
FRONT PANEL  
RELEASE BUTTON  
INSTALLING THE FRONT PANEL  
7
WIRING CONNECTION  
FOR 4x7W SYSTEM  
MAIN UNIT  
AUX(optional)  
VIDEO IN YELLOW  
RCH IN RED  
ANTENNA CONNECTOR  
LCH IN WHITE  
RCA CABLE  
GREY SUB WOOFER  
VIDEO OUT 2 YELLOW  
RED  
IGNITION  
SWITCH (B+)  
0.5A  
COAXIAL OUT BROWN  
RCH RED  
REAR RCA OUTPUT CABLE (OPTIONAL)  
FRONT RCA OUTPUT CABLE  
FUSE BOX  
MEMORY(B+)  
BACK-UP  
LCH WHITE  
YELLOW  
BLACK  
FRONT RCA  
VIDEO OUT 1 YELLOW  
FRONT RCA WHITE  
R
RED  
5A  
GROUND (B-)  
L
POWER  
BLUE  
(FOR RCA LINE OUT VERSION ONLY)  
ANTENNA  
WHITE  
GREY  
FRONT  
FRONT  
Lch SPK.  
Rch SPK  
WHITE/BLACK  
GREY/BLACK  
GREEN  
VIOLET  
REAR  
REAR  
Lch SPK.  
Rch SPK  
VIOLET/BLACK  
GREEN/BLACK  
8
11  
13  
1
12  
14  
MENU  
DISPLAY  
EJECT  
GOTO  
2
STOP  
PLAY/PAUSE  
ANGLE  
MUTE  
3
5
7
SUBTITLE  
ZOOM  
AUDIO  
SLOW  
4
6
8
15  
17  
19  
TITLE  
PBC  
REPEAT  
A-B  
16  
18  
F.FWD  
NEXT  
ENTER  
20  
21  
F.BWD  
PREV.  
9
1
2
6
9
3
4
5
7
8
SETUP  
+10  
0
10  
22  
Disc search button, cooperatively used with numeric buttons  
Display statistical disc information during playback  
Press it to eject the disc.(EJECT is enabled in DISC MODE only)  
Changing of the SUBTITLE language on multi-subtitle  
language DVD disc  
1. GOTO  
2. DISPLAY  
3. EJECT  
4. SUBTITLE  
Changing of the AUDIO soundtrack on multi-audio soundtrack  
DVD disc. Changing of the sound mode of the VCD/CD disc  
Press it to zoom the picture in scale x1.5,x2.0,x3.0  
Display the TITLE menu that is stored in DVD disc changing  
between PBC ON and PBC OFF on the VCD disc  
5. AUDIO  
6. ZOOM  
7. TITLE  
Press  
to start forward rapidly &  
to reverse rapidly  
8.  
9.  
/
Cursor buttons in MENU mode.  
Display the SETUP menu  
Press it to stop playback  
/
/
/
10.SETUP  
11  
Press once to pause a play, press again to resume playback.  
Press MENU to display the root menu of the DVD disc.  
Press it to elimate the sound immediate  
Changing for slow forward/reverse playback motion  
Changing of the view angle on multi-angle DVD disc  
Press it to repeat between two selected sports on DVD orVCD disc  
Switch the Repeat mode of DVD/VCD/CD disc  
12.  
13. MENU  
14. MUTE  
15.SLOW  
16.ANGLE  
17.A-B  
18.REPEAT  
Press  
to skip to the next track & press  
to skip back one track  
19.  
/
Confirm the Track/Chapter selected with the number key or  
selected with the cursor buttons on TV screen  
Numeric buttons  
20.ENTER  
21. 0 - 9  
22. +10  
Press it to select 10th digits  
9
Preparing the Remote Control  
Inserting the Batteries  
1.Open the battery compartment cover.  
2.Insert the new batteries. Make sure that the positive and negative terminals of the  
batteries are oriented indicated.  
3.Close the cover  
Face the remote control towards the player front face IR mark (remote control signal  
receiver).  
Operation angle: About 30 degree in each the direction of the front of the IR mark.  
10  
18  
17  
16  
15  
11  
10  
2
3
4
5
6
7
8
9
12 13 14  
1
20  
19  
ON/OFF  
Press POWER button (13) to turn on the unit. Press it again to turn off.  
FACEPLATE RELEASE  
Press REL button (2) to detach the removable faceplate.  
SET THE CLOCK  
Press CLK button (6) to change the display to clock display. Press it again to return  
to previous display. In clock display, press and hold theCLK button (6) for several  
seconds until the clock display flashes. Press VOL - (9) to change minutes or  
VOL+ (10) to change hours.  
SELECT MODE  
Press SEL button (8) to change audio mode through volume, bass, treble, balance,  
and fader modes. Use VOL + (10) and VOL- ( 9) buttons to adjust the selected mode  
When mode has not been adjusted for several seconds, display returns to normal  
radio or CD display.  
VOL  
(Volume)  
BAS  
(Bass)  
TRE  
(Treble)  
BAL  
(Balance)  
FAD  
(Fader)  
11  
Volume  
Adjust volume level by using VOL+ (10) and VOL- (9) buttons.  
Note: The unit is initially set to volume mode.  
Bass  
Press SEL button (8) one time. Adjust bass level by using VOL+(10) and VOL-(9)  
buttons.  
Treble  
Press SEL button (8) two times. Adjust treble level by using VOL+(10) and VOL  
-(9) buttons.  
Balance  
Press SEL button (8) three times. Adjust sound balance between left and right  
speakers by using VOL+(10) and VOL-(9) buttons.  
Fader  
Press SEL button (8) four times. Adjust sound balance between front and rear  
speakers by using VOL+(10) and VOL-(9) buttons.  
MUTE  
Press MU button (4) to mute down sound. Press it again to release this mode and  
recover previous volume level.  
SELECT MODE  
Press MOD button (12) to change between radio or disc mode.  
EQUALIZATION  
Press EQ button (7) to turn to equalization function and to select desired audio  
mode.  
There are four kinds of mode as below:  
FLAT  
CLAS  
ROCK  
POP  
NO EQ  
LIQUID CRYSTAL DISPLAY  
The LCD can show the current state of the unit  
SKIP TRACKS  
Press  
button(16) or  
button(15)to the previous track or the following track .  
Track number shows on the display.  
12  
FLASHING LED  
If the front panel is not on the main unit, LED (19) will be flashing.  
RESET BUTTON FUNCTION  
RESET button (20) is placed on the housing and must be activated with either a  
ballpoint pen or thin metal object. The RESET button is to be activated for the  
following reasons:  
-Initial installation of the unit when all wiring is completed.  
-All the function buttons do not operate.  
-Error symbol on the display.  
Note: If press RESET button , the unit can't work yet, please use a cotton swab  
soaked in isopropyl alcohol to clean the socket on the back of the front panel.  
RADIO OPERATION  
BAND  
Press BND button (11) to change bands as below:  
FM MW LW  
FM  
MW  
FM  
AM  
For 3 Bands (Europe)  
For 2 Bands (Europe)  
For 2 Bands (USA)  
SELECT STATION  
Rotate TUNING knob (3) clockwise or anticlockwise to adjust the frequency upward  
or downward.  
AF  
AF button (1)[ALTERNATIVE FREQUENCIES](FOR RDS ONLY)  
1. By pushing short.  
1) RADIO mode  
changed the mode to CDP mode.  
2). CDP mode  
changed the PLAY mode to PAUSE mode and vice versa.  
2. By pushing long.  
It is engaging whether "AF SEARCH" mode ON or OFF.  
If "AF SEARCH" mode is tunred on, the 1'st AF is displayed onthe LCD. All the  
AF list can be shown by pressing "DISPLAY" key during "AF SEARCH ON" mode.  
When AF is shown, the display mode changes to the frequency if the user  
changes the frequency.RDS signal is NOT received during AF search mode.  
This mode is released after few seconds. But, this mode is NOTreleased during  
changing the tunned frequency to search AF.  
LOCAL/DISTAN  
Press the LOC button (18) to select between local setting for reception of strong  
station and distant setting for reception of weak stations when tuning.  
MONO/STEREO  
In FM band, press MON button (5) to select mono or stereo reception for radio  
stations. You can sometimes improve reception of distant stations by selecting  
mono operation.  
TA  
TA function [TRAFFIC ANNOUNCEMENT] BUTTON(FOR RDS ONLY)  
When pressed short  
1). RADIO mode  
Depending on the installed option diode matrix,  
LW/MW/FM band is toggled cyclically through the tuning bands.  
-> FM -> MW -> LW (for 3 bands Europe)  
or  
13  
BASIC OPERATION  
-> FM -> MW -> (for 2 bands Europe)  
-> FM -> AM -> (for 2 bands USA)  
Refer to the explanation of diode matrix.  
2). CDP mode  
or  
or  
changed the mode to Radio mode.  
When pressed long, it is engaging whether TA mode on or off.  
When TA mode is on and a traffic announcement is transmitted:  
TA(INFO) - When the unit was in CDP mode, it will switch temporarily to radio  
mode.  
- If the volume level was under the threshold point it will be raised to the  
threshold point.  
But the user changed the volume level which was more than the threshold point  
(min .TA volume level), it will be set to the last level.  
When TA mode is on,TA of individual segment is turned on.  
- When a TP station is received,TP of individual segment is turned on.  
The current traffic announcement is canceled by pressing this key.But the TA  
mode will not be off.  
DISC OPERATION  
Most of the disc operations are controlled by the remote controller.  
Ejecting a Disc  
Press (EJECT) button (17) on the front panel or ON the remote control to eject the disc.  
Stopping Play  
-Brief press the (Stop) button to stop the unit playback, when press the  
button it can continuous normal playback.  
(14)  
-Press (Stop) button twice, it will stop the playback and go back to initial Track/Chapter.  
Rapid Forward/Rapid Reverse  
Press  
F.FWD&  
F.BWD during play.  
Each time the button is pressed, the speed of rapid forward/reverse changes according  
to the disc as follow.  
DVD:  
VCD/CD:  
Mp3:  
Normal Playback 2x  
4x  
6x  
8x  
Normal Playback  
2x  
3x  
4x  
Normal Playback  
2X  
4X  
Skipping Track  
Press  
skip to next track or back one track.  
/
on the remote handset or  
/
on the front panel during playback to  
and buttons may be un  
Note: For some VCD 2.0 dics(PBC-playback control),  
available.  
Slow Motion Play  
Press slow button during playback.Each time the button is pressed, the slow modes are  
changes according to the disc as follow.  
DVD:  
Normal Playback  
VCD:  
Normal Playback  
SF 1x  
SF 2x  
SF 3X  
SF 2x  
SF 4x  
SF 8x  
SR 8X  
SR 4X  
SR 2X  
Step BWD  
Note: For VCD, in any slow mode, press ENTER button to return to normal playback.  
14  
Pause (still picture)  
On-Screen Display Function  
Press the DISPLAY button during  
playback to display the contents of the  
current disc on the screen.  
Example:  
Pressing  
during playback will stop  
play temporary. Return to normal  
playback, press  
once again.  
Repeat  
DVD:  
Press the REPEAT button to select repeat  
mode as follow.  
(1) Press DISPLAY for the first time:  
DVD:  
TITLE 01/03 CHAPTER 002/025 P: 00:00:25  
TITLE ELAPSED  
Press the REPEAT button to select repeat  
mode as follow.  
CHAPTER REPEAT ON  
TITLE REPEAT ON  
REPEAT OFF  
Title Number, Total Title Number, Chapter  
Number, Total Chapter Number of this  
Title of the disc currently being played  
will be shown on the screen, along with  
the elapsed time.  
VCD/CD:  
Press the REPEAT button to select repeat  
mode as follow.  
REP-ONE  
REP-ALL  
REPEAT OFF  
(2) Press DISPLAY for the second time:  
TITLE 01/03 CHAPTER 002/025 P: 00:00:25  
TITLE REMAIN  
1.Continuously repeat at the current chapter/  
track, when selected REP-ONE mode.  
2.Select REP-ALL mode to continuously  
repeat all chapter/track on the current  
disc.  
(3) Press DISPLAY for the third time:  
3.When the player finish playback the  
current discc last chapter/track, it will  
stop display the elapsed time.  
When selected REPEAT OFF mode  
(REP-ONE & REP-ALL disappear at  
the screen display).  
TITLE 01/03 CHAPTER 002/025 P: 00:00:25  
CHAPTER ELAPSED  
(4) Press DISPLAY for the fourth time:  
4.REPEAT feature does not supportVCD2.0  
(with PBC ON).  
TITLE 01/03 CHAPTER 002/025 P: 00:00:25  
CHAPTER REMAIN  
Remote Sensor (IR)  
Point the remote handset to the remote  
sensor. Receive the signal from remote  
handset.  
(5) Press DISPLAY for the fifth time:  
The message on thescreen willbecleared.  
Video CD/SVCD/CD:  
(1) Press DISPLAY for the first time:  
T:01/18 P: 00:00:25 LR DISC  
SINGLE ELAPSED  
15  
(2) Press DISPLAY for the second time:  
VCD:  
Press AUDIO during playback.  
It is possible to switch the sound  
between monaural and stereo sound.  
T:01/18 P: 00:00:25 LR DISC  
SINGLE REMAIN  
LEFT VOCAL  
RIGHT VOCAL  
MONO LEFT  
(3) Press DISPLAY for the third time:  
STEREO MONO RIGHT  
T:01/18 P: 00:00:25 LR DISC  
TOTAL ELAPSED  
CD:  
Press AUDIO during playback.  
It is possible to switch the sound  
between monaural and stereo sound.  
(4) Press DISPLAY for the fourth time:  
MONO LEFT  
MONO RIGHT  
STEREO  
T:01/18 P: 00:00:25 LR DISC  
TOTAL REMAIN  
TITLE Menu Function  
DVD:  
(5) Press DISPLAY for the fifth time:  
The message on the screen will be cleared  
for SVCD and VCD. Note: For CD and  
Mp3, the message will always display  
on the screen.  
If the DVD has multiple titles recorded on  
the disc. It can select preferred title from  
the title menu to start playback.  
1.Press TITLE during playback.  
The title menu is display.  
2.Press the cursor button shown in TV  
screen, select preferred title by the  
cursor button and confirmed by  
ENTER key.  
MP3:  
Each time DISPLAY is pressed, the  
message displayed on screen changes  
as follows:  
VCD:  
Press MENU button while the disc is  
playing, you can switch between"PBC  
on"and "PBC off"mode.  
SINGLE ELAPSED  
SIGGLE REMAIN  
Multi-audio Language Function  
DVD:  
Multi-subtitle Language Function  
(For DVD only)  
Press AUDIO during playback.  
Each time the button is pressed, number  
of the audio soundtrack language  
changes on sequential order.  
Notes:  
-The language number is different  
according to the disc.  
-Some disc only contain one language  
soundtrack.  
Press SUBTITLE during playback.  
Each time the button is pressed, number  
of the subtitle language changes in  
sequential order.  
Notes:  
-The language number is different  
according to the disc.  
-Some discs only contain one  
subtitle language.  
-When no different subtitle language  
are recorded, will be displayed at  
screen left top corner.  
-When no different language  
soundtrack are recorded will be  
display at screen left top corner.  
16  
Multi-angle Function  
(For DVD only)  
Press ANGLE during playback.  
MP3 Disc Play  
MP3 disc is playing as the format of  
FOLDER by FOLDER.  
Each time the button is pressed, number For example:  
of the angle changes in sequential order.  
Notes:  
Mp3 PLAYER  
ROOT  
-The angle number is different according  
ROOT  
0
1
to the disc.  
-The function only work for discs having  
scenes recorded at different angles.  
-When no different angle are recorded,  
will be displayed at screen left top  
corner.  
MP3 MUSIC  
SKY  
MP3 HEAR YOUR  
Use  
/
/
/
to select the item or  
folder, then press ENTER button.  
Pressing REPEAT button repeatedly can  
select three kinds of repeat play mode.  
REP-ONE:  
Play the same song over and over again.  
FOLDER REPEAT:  
Play all songs in the current directory in  
sequence, over and over again.  
DISC REPEAT:  
Play all songs in the disc over and  
over again.  
In the playback, use  
item ahead or back.  
: Rapid reverse,  
or  
to skip an  
: Rapid advance  
Note: The FOLDER cannot be selected  
during playing. It can be selected after  
(Stop) button pressed.  
17  
INITIAL SETUP  
SETUP MENU --- MAIN PAGE---  
GENERAL SETUP  
--- GENERAL PAGE ---  
GENERAL SETUP  
SPEAKER SEUP  
AUDIO SETUP  
NORMAL/PS  
NORMAL/LB  
TV DISPLAY  
PIC MODE  
ANGLE MARK  
OSD LANG  
CAPTIONS  
SCR SAVER  
WIDE  
PREFERENCES  
EXIT SETUP  
1.Press SETUP in the stop mode.  
(Press the stop button twice to ensure  
the player under STOP mode.)  
MAIN PAGE  
TV Screen  
2.The initial SETUP menu is displayed.  
3.Select the preferred item by using the  
Video  
Material  
Wide(16:9)  
Pan Scan  
Normal  
Letter-box  
4:3  
/
buttons.  
4.Press ENTER buttons.  
a. GENERAL SETUP  
This setup page includes all the  
item of TV display & audio output  
TV display setup  
This is to select the appropriate TV  
feature. The detail please refer to aspect (4:3 or 16:9) according to the  
GENERAL SETUP MENU.  
b. SPEAKER SETUP  
connected TV set.  
Normal/PS (For 4:3 TV)  
This is to activate the audio output  
from DOLBY AC3 5.1 DOWNMIX  
Played back in the PAN & SCAN style.  
(If connected to wide-screen TV, the left  
to 2 channel mode. Please refer to and right edges are cut off.)  
SPEAKER SETUP MENU.  
c. AUDIO SETUP  
Normal/LB (For 4:3 TV)  
Played back in letterbox style.  
(If connected to wide-screen TV, black  
bands appear at top and bottom of the  
screen.)  
This setup page includes all the  
items for AUDIO. Please refer to  
AUDIO SETUP MENU.  
Wide (For 16:9 TV)  
Select when a wide-screen TV set is  
connected.  
d. PREFERENCE SETUP  
This setup page includes all the  
configuration of support feature.  
The detail please refer to  
PREFERENCES SETUP MENU.  
18  
--- GENERAL PAGE ---  
TV DISPLAY  
--- GENERAL PAGE ---  
TV DISPLAY  
PIC MODE  
AUTO  
HI-RES  
PIC MODE  
ANGLE MARK  
OSD LANG  
CAPTIONS  
SCR SAVER  
ANGLE MARK  
OSD LANG  
CAPTIONS  
SCR SAVER  
N-FLICKER  
ENGLISH  
MAIN PAGE  
MAIN PAGE  
PIC mode setup  
OSD LANG type setup  
Select AUTO, the player PIC mode will  
depend on DVD disc.  
Select the preferred OSD language by  
using the buttons.  
/
Select HI-RES format for best image  
resolution.  
Select N-FLICKER format on format on  
image or picture under noise affect.  
--- GENERAL PAGE  
TV DISPLAY  
PIC MODE  
--- GENERAL PAGE ---  
TV DISPLAY  
PIC MODE  
ANGLE MARK  
OSD LANG  
ANGLE MARK  
OSD LANG  
CAPTIONS  
SCR SAVER  
ON  
CAPTIONS  
SCR SAVER  
ON  
OFF  
OFF  
MAIN PAGE  
MAIN PAGE  
ANGLE MARK display setup  
CAPTIONS setup  
If it is set to ON, when the multi-angle  
Activate the CAPTIONS feature by  
DVD disc is playing, (the angle mark) selecting ON. And release this feature  
will appears on the screen; if is set to  
OFF, the mark will not appear.  
by selecting OFF.  
19  
AUDIO SETUP  
--- AUDIO SETUP ---  
--- GENERAL PAGE ---  
TV DISPLAY  
AUDIO OUT  
OP MODE  
ANALOG  
SPDIF/RAW  
SPDIF/PCM  
PIC MODE  
LPCM OUTPUT  
DYNAMIC  
ANGLE MARK  
OSD LANG  
CAPTIONS  
SCR SAVER  
ON  
OFF  
MAIN PAGE  
MAIN PAGE  
AUDIO OUT  
SCR SAVER setup  
This is to activate the audio output from  
ANALOG mode to SPDIF/RAW mode to  
SPDIF/PCM mode.  
Select the SCR SAVER output ON/OFF.  
SPEAKER SETUP  
--- AUDIO SETUP ---  
--- SPEAKER SETUP PAGE ---  
DOWNMIX  
LT/RT  
AUDIO OUT  
OP MODE  
LINE MODE  
RF REMOD  
STEREO  
MAIN PAGE  
LPCM OUTPUT  
DYNAMIC  
MAIN PAGE  
OP MODE  
This is to activate the audio output from  
DOLBYAC3 5.1 DOWNMIX to 2 channel  
mode. Select the preferred SPEAKER  
connection by using the cursor buttons.  
Select the LT/RT to activate the Dolby  
surround compatible output.  
There are two operating modes for the  
Dolby Digital decoder: LINE OUT and  
RF REMOD.  
Select the STEREO to activate simple  
stereo mode.  
20  
PREFERENCES SETUP  
--- AUDIO SETUP---  
AUDIO OUT  
--- PREFERENCES PAGE ---  
TV TYPE  
MULTI  
NTSC  
PAL  
AUDIO  
OP MODE  
SUBTITLE  
DISC MENU  
PARENTAL  
PASSWORD  
LPCM OUTPUT  
DYNAMIC  
LPCM 48K  
LPCM 96K  
DEFAULTS  
MP3 PLAY  
MAIN PAGE  
MAIN PAGE  
TV type setup  
LPCM OUTPUT  
This player can play discs recorded in  
either PAL or NTSC format.  
Select NTSC format, when you connected  
to NTSC TV.  
Select PAL format, when you connected  
to PAL TV.  
Select AUTO format, the player TV  
output format will according to the DVD  
disc format.  
Select the LPCM OUTPUT between  
LPCM 48K and LPCM 96K.  
--- AUDIO SETUP ---  
AUDIO OUT  
FULL  
OP MODE  
6/8  
--- PREFERENCES PAGE ---  
LPCM OUTPUT  
TV TYPE  
4/8  
DYNAMIC  
AUDIO  
ENGLISH  
FRENCH  
SPANISH  
CHINESE  
JAPANESE  
2/8  
SUBTITLE  
DISC MENU  
PARENTAL  
PASSWORD  
OFF  
MAIN PAGE  
DEFAULTS  
MP3 PLAY  
MAIN PAGE  
Dynamic Range Control  
Select DRC and adjust the dynamic  
range of a Dobly Digital encoded  
program. There are 8 steps between full  
compression and off compression.  
AUDIO language setup  
Select the preferred AUDIO soundtrack  
by using the cursor buttons.  
21  
--- PREFERENCES PAGE ---  
TV TYPE  
--- PREFERENCES PAGE ---  
TV TYPE  
1G  
AUDIO  
AUDIO  
2
ENGLISH  
FRENCH  
SPANISH  
SUBTITLE  
DISC MENU  
PARENTAL  
PASSWORD  
SUBTITLE  
DISC MENU  
PARENTAL  
PASSWORD  
3PG  
4PG13  
5
CHINESE  
6PG-R  
JAPANESE  
OFF  
DEFAULTS  
MP3 PLAY  
MAIN PAGE  
DEFAULTS  
MP3 PLAY  
7NC-17  
8 ADULT  
MAIN PAGE  
NO PARENTAL  
PARENTAL  
Select the preferred SUBTITLE language  
by using the cursor buttons.  
Select suitable parental guidance by the  
cursor buttons and conformed by  
pressing ENTER button.  
--- PREFERENCES PAGE---  
--- PREFERENCES PAGE ---  
TV TYPE  
AUDIO  
TV TYPE  
AUDIO  
SUBTITLE  
DISC MENU  
PARENTAL  
SUBTITLE  
DISC MENU  
PARENTAL  
PASSWORD  
ENGLISH  
FRENCH  
SPANISH  
PASSWORD  
CHANGE  
DEFAULTS  
MP3 PLAY  
MAIN PAGE  
DEFAULTS  
MP3 PLAY  
MAIN PAGE  
CHINESE  
JAPANESE  
Select the preferred DISC MENU  
Select the change and press ENTER  
language by using the cursor buttons.  
button. Type the old password (The initial  
factory code is  
) and key in 4  
characters password now you want to  
use, and retype again to confirm key in  
correctly.  
22  
--- PREFERENCES PAGE ---  
DEFAULTS TABLE  
Normal/PS  
General Setup  
TV Display  
PIC Mode  
TV TYPE  
AUDIO  
AUTO  
ON  
Angle Mark  
SUBTITLE  
DISC MENU  
PARENTAL  
PASSWORD  
OSD Language  
Captions  
English  
OFF  
SCR Saver  
OFF  
Stereo  
Analog  
Speaker Setup Downmix  
Audio Out  
Audio Setup  
RESET  
DEFAULTS  
MP3 PLAY  
MAIN PAGE  
OP Mode  
Dynamic  
Line Out  
LPCM 96K  
AUTO  
LPCM Out  
TV Type  
Audio  
Preferences  
DEFAULTS  
English  
English  
English  
Select reset to become factory initial  
Subtitle  
setting.  
DISC Menu  
--- PREFERENCES PAGE ---  
Parental  
NO PARENTAL  
Password  
Smart NAV  
3308  
TV TYPE  
With Menu  
AUDIO  
SUBTITLE  
DISC MENU  
PARENTAL  
PASSWORD  
DEFAULTS  
NO MENU  
MP3 PLAY  
WITH MENU  
MAIN PAGE  
Mp3 PLAY  
In this item, you can select NO MENU  
mode or WITH MENU mode.  
23  
Supply Voltage:  
Current Consumption:  
Signal System:  
12V DC (11V-15V), test voltage 14.4V, negative ground  
Less than7 A  
Compositive video 1.0Vp-p 75  
Discs Played:  
(1)DVD-VIDEO Disc  
5"(12 cm) single-sided, single-layer  
5"(12 cm) single-sided, double-layer  
(2)Compact Disc (CD-DA, VIDEO CD)  
5"(12cm) disc  
Audio Output Level:  
Audio Signal Output:  
Characteristics:  
600 (2 ch 2.0 Vrms)  
(1)Frequency Response  
(2)S/N Ratio  
20 Hz - 20 KHz  
90 dB (JIS)  
(3)Wow and Flutter  
Below measurable limits  
For 3 Bands  
(Europe)  
For 2 Bands  
(Europe)  
For 2 Bands  
(U.S.A.)  
FM  
FM  
FM  
Frequency Coverage:  
IF:  
Sensitivity (S/N = 30 dB):  
88 to 108 MHz 88 to 108 Mhz 88 to 108 MHz  
10.7 MHz  
15 dBu  
10.7 MHz  
15 dBu  
10.7 MHz  
15dBu  
MW  
MW  
AM  
Frequency Coverage:  
IF:  
Sensitivity (S/N = 20 dB):  
540 to 1600 KHz 540 to 1600 KHz 530 to 1710 KHz  
455 KHz  
40 dBu  
455 KHz  
40 dBu  
455 KHz  
40 dBu  
LW  
Frequency Coverage:  
IF:  
Sensitivity (S/N = 20 dB):  
150 to 280 KHz  
455 KHz  
45 dBu  
Note:  
Specifications and design are subject to modification, without notice, due to  
improvements in technology.  
24  
Before going through the check list, check wiring connection. If any of the problems  
persist after check list has been made, consult your nearest service dealer.  
Symptom  
Cause  
Solution  
If the power supply is properly  
connected to the car accessory  
terminal,switch the ignition key  
to "ACC"  
The car ignition switch is  
not on.  
No power.  
The fuse is blown.  
Replace the fuse.  
Remove the disc in the player,  
Then put a new one  
Presence of disc inside the  
player.  
Inserting the disc in reverse  
direction.  
Insert the compact disc with  
the label facing upward.  
Disc cannot be  
loaded or ejected.  
The disc is extremely dirty or  
defective.  
Clean the disc or try to play a  
new one.  
Temperature inside the car  
is too high.  
Cool off or until the ambient  
temperature return to normal.  
Leave the player off for an hour  
then try again.  
Condensation.  
Adjust volume to a desired level.  
Check wiring connection.  
Volume is in minimum.  
No sound.  
Wiring is not properly  
connected.  
Adjust the installation angle less  
than 30 degrees.  
The installation angle is  
more than 30 degrees.  
Sound skips.  
The disc is extremely dirty  
or defective disc.  
Clean the compact disc, then  
try to play a new one.  
Press the RESET button.  
Front panel is not properly fixed  
into its place.  
The built-in microcomputer  
is not operating properly  
due to noise.  
The operation keys  
do not work.  
The antenna cable is not  
connected.  
Insert the antenna cable firmly.  
Select a station manually.  
The radio does not  
work.  
The signals are too weak.  
This product incorporates copyright protection technology that is protected by method  
claims of certain U.S. patents and other intellectual property rights owned by  
Macrovision Corporation and other rights owners. Use of this copyright protection  
technology must be authorized by Macrovision Corporation, and is intended for home  
and other limited viewing uses only unless otherwise authorized by Macrovision  
Corporation. Reverse engineering or disassembly is prohibited.  
25  
88-V2420-03  

Kyocera All in One Printer 3050ci User Manual
LaCie Computer Drive 2big USB 30 User Manual
Lennox Hearth Door 36LBF User Manual
Leviton Network Router 47611 GB4 User Manual
LG Electronics Computer Monitor E1951C User Manual
Life Fitness Home Gym Smith Machine User Manual
Makita Power Hammer HM1214C User Manual
Master Appliance Soldering Gun UT 100 User Manual
McCulloch Lawn Mower MC19538LT User Manual
Melissa Coffeemaker 745 182 User Manual