9224-2776-11 H-A112
E
INSTRUCTION MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
FOR PROPER AND SAFE USE
NP-200 Lithium-ion batteries
The DiMAGE X operates on a small, but powerful lithium-ion battery. Misuse or abuse of the lithium-
ion battery can cause damage or injury through fire, electric shock, or chemical leakage.
Read and understand all warnings before using the battery.
DANGER
• Do not short, disassemble, damage, or modify the battery.
• Do not expose the battery to fire or high temperatures over 60°C (140°F).
• Do not expose the battery to water, or moisture. Water can corrode or damage the internal battery
safety devices and cause the battery to overheat, ignite, rupture, or leak.
• Do not drop or subject the battery to strong impacts. Impacts can damage the internal battery safe-
ty devices and cause the battery to overheat, ignite, rupture, or leak.
• Do not store the battery near or in metallic products.
• Only use the battery specified in this camera manual.
• Only use the specified charger within the voltage range specified on the charger unit. An inappropri-
ate charger or current may cause damage or injury through fire or electric shock.
• Do not use a leaking battery. If fluid from the battery enters your eye, immediately rinse the eye
with plenty of fresh water and contact a doctor. If fluid from the battery makes contact with your
skin or clothing, wash the area thoroughly with water.
(Continued on the next page.)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
FOR PROPER AND SAFE USE
WARNING
• Tape over the lithium-ion battery contacts to avoid short-circuiting during disposal; always follow
local regulations for battery disposal.
• Only use the battery specified in this manual.
• If charging is not completed after the specified period elapses, unplug the charger and discontinue
charging immediately.
• Only use or charge the battery in an environment with ambient temperatures between 0° and 40°C
(32° and 104°F) and a humidity of 45% to 85% RH. Only store the battery in an environment with
ambient temperatures between -20° and 30°C (-4° and 86°F) and a humidity of 45% to 85% RH.
General warnings and cautions for product use.
Read and understand the following warnings and cautions for safe use of the digital camera and its
accessories.
WARNING
• Do not disassemble the camera or charger. Electric shock may cause injury if a high voltage circuit
inside the product is touched.
• Immediately remove the battery or unplug the AC adapter and discontinue use if the camera is
dropped or subjected to an impact in which the interior, especially the flash unit, is exposed. The
flash has a high voltage circuit which may cause an electric shock resulting in injury. The continued
use of a damaged product or part may cause injuries or fire.
• Keep the battery, memory card, or small parts that could be swallowed away from infants. Contact
a doctor immediately if an object is swallowed.
• Store this product out of reach of children. Be careful when around children, not to harm them with
the product or parts.
• Do not fire the flash directly into the eyes. It may damage eyesight.
• Do not fire the flash at vehicle operators. It may cause a distraction or temporary blindness which
may lead to an accident.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
• Do not use the monitor while operating a vehicle or walking. It may result in injury or an accident.
• Do not use this product in a humid environment, or operate these products with wet hands. If liquid
enters this product, immediately remove the battery or unplug the power cord, and discontinue use.
The continued use of a product exposed to liquids may cause damage or injury through fire or elec-
tric shock.
• Do not use this product near inflammable gases or liquids such as gasoline, benzine, or paint thin-
ner. Do not use inflammable products such as alcohol, benzine, or paint thinner to clean these
products. The use of inflammable cleaners and solvents may cause an explosion or fire.
• When unplugging the AC adapter or charger, do not pull on the power cord. Hold the plug when
removing it from an outlet.
• Do not damage, twist, modify, heat, or place heavy objects on the AC adapter or charger cord. A
damaged cord may cause damage or injury through fire or electric shock.
• If these products emit a strange odor, heat, or smoke, discontinue use. Immediately remove the
battery taking care not to burn yourself as the battery may become hot with use. The continued use
of a damaged product or part may cause injuries or fire.
• Only use the specified AC adapter within the voltage range indicated on the adapter unit. An inap-
propriate adapter or current may cause damage or injury through fire or electric shock.
• Take the product to a Minolta Service Facility when repairs are required.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
FOR PROPER AND SAFE USE
CAUTION
• Do not use or store these product in a hot or humid environment such as the glove compartment or
trunk of a car. It may damage the camera, charger, and battery which may result in burns or injuries
caused by heat, fire, explosion, or leaking battery fluid.
• If the battery is leaking, discontinue use of the product.
• The camera, charger, and battery temperature rises with extended periods of use. Care should be
taken to avoid burns.
• Burns may result if the memory card or battery is removed immediately after extended periods of
use. Turn the camera off and wait for it to cool.
• Do not fire the flash while it is in contact with people or objects. The flash unit discharges a large
amount of energy which may cause burns.
• Do not apply pressure to the LCD monitor. A damaged monitor may cause injury, and the liquid
from the monitor may cause inflammation. If liquid from the monitor makes contact with skin, wash
the area with fresh water. If liquid from the monitor comes in contact with the eyes, immediately
rinse the eyes with plenty of water and contact a doctor.
• When using the AC adapter and charger, insert the plug securely into the electrical outlet.
• Do not use if the AC adapter or charger cord is damaged.
• Do not cover the AC adapter or charger. A fire may result.
• Do not obstruct access to the AC adapter or charger; this can hinder the unplugging of the units in
emergencies.
• Unplug the AC adapter or charger when cleaning or not in use.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
ABOUT THIS MANUAL
The getting up and running section covers how to prepare the camera for use. It contains important
information about power supplies and memory cards. The basic operation of this camera is covered
in the recording-mode section between pages 20 and 29, and the playback-mode section between
pages 50 and 56. Read the data-transfer mode section in its entirety before connecting the camera
to a computer.
Many of the features of this camera are controlled with menus. The menu navigation sections
concisely describe how to change menu settings. Descriptions of the settings immediately follow the
navigation sections.
The appendix contains a troubleshooting section to help answer questions about the operation of the
camera. Information covering camera care and storage is also provided. Please store this manual in
a safe place.
Names of parts ....................................................................................................................................10
Getting up and running.........................................................................................................................12
Charging the lithium-ion battery ..............................................................................................12
Changing the lithium-ion battery..............................................................................................13
Battery-condition indicator.......................................................................................................14
Auto power off .........................................................................................................................14
AC adapter (sold separately)...................................................................................................15
Attaching the hand strap .........................................................................................................15
Installing and removing a memory card ..................................................................................16
About memory cards ...............................................................................................................17
Setting the date and time ........................................................................................................18
Recording mode...................................................................................................................................20
Handling the camera ...............................................................................................................20
Setting the camera to record images ......................................................................................20
Using the zoom lens................................................................................................................21
LCD monitor display - recording mode....................................................................................22
Camera-shake warning ...........................................................................................................22
Basic recording operation........................................................................................................23
Focus lock ...............................................................................................................................24
Focus range.............................................................................................................................24
7
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Focus signals...........................................................................................................................25
Special focusing situations ......................................................................................................25
Flash modes............................................................................................................................26
Flash range..............................................................................................................................27
Flash signals............................................................................................................................27
Navigating the recording-mode menu .....................................................................................28
Drive modes ............................................................................................................................30
Single-frame advance.................................................................................................30
Continuous advance...................................................................................................31
Self-timer.....................................................................................................................32
Movie recording ..........................................................................................................33
Audio recording...........................................................................................................34
Image size ...............................................................................................................................35
Image quality ...........................................................................................................................36
The frame counter and memory card capacity........................................................................37
White balance..........................................................................................................................38
Automatic white balance.............................................................................................38
Preset white balance ..................................................................................................39
Digital zoom.............................................................................................................................40
Instant playback.......................................................................................................................41
Voice memo.............................................................................................................................42
Folder name ............................................................................................................................43
LCD brightness........................................................................................................................44
Auto-power-off menu settings..................................................................................................44
Audio signals ...........................................................................................................................44
Setting the date and time ........................................................................................................45
Setting the date format............................................................................................................45
Exposure compensation..........................................................................................................46
What is an Ev? ........................................................................................................................47
Display button - recording mode .............................................................................................48
A short guide to photography ..................................................................................................49
Playback mode ....................................................................................................................................50
Single-frame playback display.................................................................................................50
Viewing images and playing back audio recordings ...............................................................51
Display button - playback mode ..............................................................................................52
Enlarged playback...................................................................................................................53
Navigating the playback-mode menu......................................................................................54
Frame-selection screen...........................................................................................................56
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio captioning......................................................................................................................57
Deleting image and audio files ................................................................................................58
Locking image and audio files.................................................................................................59
About DPOF ............................................................................................................................60
Creating a DPOF print order ...................................................................................................60
Ordering an index print............................................................................................................61
Formatting memory cards........................................................................................................62
Video output ............................................................................................................................62
Language.................................................................................................................................62
Viewing images on a television ...............................................................................................63
Data-transfer mode ..............................................................................................................................64
DiMAGE X system requirements.............................................................................................64
Connecting the camera to a computer....................................................................................65
Connecting to Windows 98 and 98SE.....................................................................................67
Automatic installation..................................................................................................67
Manual installation......................................................................................................68
Connecting to Mac OS 8.6 ......................................................................................................70
QuickTime system requirements.............................................................................................70
Auto power off – data-transfer mode.......................................................................................70
Changing the memory card - data-transfer mode ...................................................................71
Memory card folder organization.............................................................................................72
Disconnecting the camera from the computer ........................................................................74
Windows 98 and 98SE ...............................................................................................74
Windows Me, 2000 Professional, and XP ..................................................................74
Macintosh....................................................................................................................75
Appendix
....................................................................................................................................76
Setting the menu language .....................................................................................................76
Troubleshooting.......................................................................................................................77
Care and storage.....................................................................................................................82
Technical specifications...........................................................................................................86
9
Download from Www.Somanuals.com. All Manuals Search And Download.
NAMES OF PARTS
* This camera is a sophisticated optical instrument. Care should be taken to keep these surfaces
clean. Please read the care and storage instructions in the back of this manual (p. 82).
Flash (p. 26)
Main switch
Self-timer lamp (p. 32)
Shutter-release button
Viewfinder window*
Microphone
Lens*
DC terminal (p. 15)
Strap eyelet (p. 15)
Tripod socket
(Located on the bottom of the
body.)
Battery/Card chamber door (p. 13, 16)
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewfinder*
Indicator lamp (p. 81)
Left key
Right key
Zoom lever (p. 21)
Mode switch
Recording mode (p. 20)
Playback mode (p. 50)
LCD monitor*
Speaker
Enter button
Menu button
Flash-mode button (p. 26)
Display button (p. 48, 52)
AV-out-terminal/USB-port cover
11
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING UP AND RUNNING
GETTING UP AND RUNNING
This section covers how to prepare your camera for use. Details on the use and installation of the
battery and memory card are given as well as how to attach the hand strap and optional AC adapter.
Charging the lithium-ion battery
Before the camera can be used, the lithium-ion battery must be charged. Before charging the battery,
read the safety warnings on pages 3 and 4 of this manual. Only recharge the battery with the sup-
plied battery charger. The battery should be recharged before each shooting session. See page 83
for battery care and storage.
Plug the power cord into the charger unit (1).
With the battery terminals toward the front and the label
face up, slide the battery into the charger (2).
1
2
Plug the charger into a live household outlet.
• After a few seconds, the indicator lamp (3) will glow
to show the battery is charging. The lamp will go out
when the battery has been charged. Charging time is
approximately eighty minutes.
4
Unplug the power cord from the outlet.
Remove the battery from the charger (4).
3
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the lithium-ion battery
This digital camera uses one NP-200 lithium-ion battery. Before using the battery, read the safety
warnings on pages 3 and 4 of this manual. When replacing the battery, the camera should be turned
off.
2
Slide the battery-chamber door toward the bottom of the camera to
release the safety catch (1). Open the door (2).
4
1
Move the battery latch towards the back of the camera to
insert the battery (3). Slide the battery into the battery cham-
ber (4) with the battery terminals first until it is caught by the
latch.
6
3
To remove the battery, move the latch towards the back
of the camera until the battery is released (5). Pull the
battery out of the chamber (6).
5
7
8
Close the battery-chamber door (7) and slide it toward the top of the
camera to engage the safety catch (8).
• After installing the battery, the set-time/date message may appear
on the monitor. The clock and calendar is set in the setup 1 section
of the menu (p. 18).
13
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING UP AND RUNNING
Battery-condition indicator
This camera is equipped with an automatic battery-condition indicator displayed on the LCD monitor.
The icon will change from white to red when battery power is low.
Full-battery icon - the battery is fully charged. This icon is displayed for three
seconds when the camera is switched on or switched between the recording
or playback mode.
Half-full-battery icon - the battery is partially charged. This icon is displayed
for three seconds. The LCD monitor will turn off when the flash is charging.
Low-battery warning - battery power is very low. The battery should be
replaced as soon as possible. This warning automatically appears and
remains on the monitor until the battery is recharged. If the power level falls
below this level when the camera is on, the battery-exhausted message will
appear just before the camera shuts down.
If power is insufficient for camera operation, the indicator lamp next to the
viewfinder will turn red and blink for three seconds. The shutter will not
release. The battery must be recharged.
Auto power off
To conserve battery power, the camera will shut down if an operation is not made within three min-
utes. To restore power, press the main switch. The length of the auto-power-off period can be
changed in the setup 1 section of the recording and playback-mode menu (p. 28, 54). When the
camera is connected to a computer, the auto-power-off period is set to ten minutes and cannot be
changed.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
AC adapter (sold separately)
Do not change the power supply while the camera is on.
Always turn off the camera before changing between power supplies.
The AC adapter AC-4 or AC-5 allows the camera to be powered from a
household outlet. The AC adapter is recommended when the camera is
interfaced with a computer or during periods of heavy use. AC adapter model
AC-4 is for use in North America, Japan, and Taiwan, and AC-5 is for use in all
other areas.
1
Insert the mini plug of the AC adapter into the DC terminal (1).
Insert the AC adapter plug into an electrical outlet.
Attaching the hand strap
Always keep the strap around your wrist in case that the
camera is accidentally dropped.
Pass the small loop of the hand strap through the strap eyelet on
the camera body (1).
2
Pass the other end of the strap through the small loop and tighten
(2).
1
15
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING UP AND RUNNING
Installing and removing a memory card
Always turn off the camera and confirm the indicator lamp is not orange
and blinking before changing the memory card, otherwise the card may be
damaged, and data lost.
An SD (Secure Digital) Memory card or MultiMediaCard must be
inserted for the camera to operate. If a card has not been inserted,
a no-card warning will appear on the LCD monitor; the shutter can
2
still be released.
3
Slide the battery-chamber door toward the bottom of the camera
to release the safety catch (1). Open the door (2).
1
Insert the memory card all the way into the card slot and then
release (3). The card should catch in the slot.
4
• Insert the card so the face is toward the front of the camera.
Always push the card in straight, never at an angle. Never force
the card. If the card does not fit, check that it is orientated
correctly.
• If a MultiMediaCard is inserted incorrectly, it will lock, but the
card chamber door will not close.
5
To eject a memory card, press the card into the slot and release
(4). The card can now be pulled out.
6
Close the battery-chamber door (5) and slide it toward the top of
the camera to engage the safety catch (6).
16
Download from Www.Somanuals.com. All Manuals Search And Download.
About memory cards
The response time during recording and playback is longer with MultiMediaCards compared with SD
Memory Cards. This is not a defect, but rather due to the specifications of the cards. When using
large capacity cards, some operations like deletion may take longer.
The SD Memory Card has a write-protect switch to prevent image
Write-
protect
switch
data from being deleted. By sliding the switch to the bottom of the
card, the data will be protected. However, when the card is protect-
ed, images cannot be recorded. If an attempt is made to record or
delete an image with the camera, the card-locked message will
appear and the LED lamps near the viewfinder will turn red and
blink quickly. For memory card care and store see page 82.
If the unable-to-use-card message appears, the inserted card in
the camera may need to be formatted. A card used in another
camera may also have to be formatted before being used. A card
can be formatted in the setup 2 section of the playback menu (p.
54). When a card is formatted, all the data on the card is perma-
nently erased.
Lock
position
17
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING UP AND RUNNING
Setting the date and time
After initially inserting a memory card and charging the battery, the camera’s clock and calendar
must be set. When images are recorded, the image data is saved with the date and time of record-
ing. Depending on the region, the menu language may also have to be set. To change the language,
refer to page 76.
Turn the camera on by pressing the main
switch near the shutter-release button (1).
1
Slide the mode switch to the playback posi-
tion (2).
4
2
The date and time can be set on the play-
back menu. Navigating the menu is simple.
The menu button (3) turns the menu on and
off. The zoom lever and left and right keys
(4) control the cursor and change settings
on the menu. The enter button (5) selects
menu options and sets adjustments.
3
5
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Press the menu button to activate the play-
back menu.
Basic
Setup 1 Setup 2
LCD brightness
Power off
-
3 min.
Use the right key to highlight the setup 1
tab at the top of the menu.
Audio signals
Date/Time set
Date format
On
-
Use the zoom lever to highlight the
date/time-set menu option.
YYYY/MM/DD
Playback menu: setup 1 section
Date/Time set
Press the right key. “Enter” will appear on
the right side of the menu.
Press the enter button to display the date/time setting
screen.
Use the left and right keys to select the item to
be changed. Use the zoom lever to adjust the
item.
Enter
Date/Time setting screen
Press the enter button to set the clock and calendar.
The playback menu will be displayed.
Press the menu button to close the playback menu.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING MODE
RECORDING MODE
This section covers the basic recording operation as well as advanced recording functions. To start
using the camera, read pages 20 through 29. Many of the recording functions are controlled with
menus. The menu navigation sections concisely describe how to change menu settings. Descriptions
of the settings immediately follow the navigation section.
Handling the camera
While using the viewfinder or LCD monitor, grip the camera firmly with
your right hand while supporting the camera body with your left. Keep
your elbows at your side and your feet shoulder-width apart to hold the
camera steadily.
When taking vertical pictures, hold the camera so that the flash is
above the lens with the shutter-release button to the top. Take care not
to cover the lens with your fingers or the strap.
Setting the camera to record images
1
Turn the camera on by pressing the main switch (1).
Slide the mode switch to the recording position (2).
2
2
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the zoom lens
This camera is equipped with a unique 5.7 - 17.1mm zoom lens. This is equivalent to a 37 to 111mm
lens on a 35mm camera. The lens is controlled by the zoom lever at the back of the camera.
In 35mm photography, focal lengths below 50mm are referred to as wide-angle; the angle of view is
larger than that of the human eye. Above 50mm is referred to as telephoto and makes distant objects
appear closer. The effect of the optical zoom is visible in both the viewfinder and LCD monitor.
To zoom in on the subject, push the
zoom lever up.
To zoom out, push the zoom lever
down.
The digital-zoom function can double
the power of the lens. The digital zoom
is activated in the custom section of the
recording-mode menu (p. 28).
21
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING MODE
LCD monitor display - recording mode
Microphone indicator
Digital zoom (p. 40)
Image size (p. 35)
Recording mode
Flash modes (p. 26)
Image quality (p. 36)
Exposure compensation (p. 46)
White balance (p. 38)
Battery-condition indicator
(p. 14)
Drive mode (p. 30)
Frame counter (p. 37)
Camera-shake warning Focus signals (p. 27)
The frame counter cannot exceed 999. When the number of recordable images exceeds this, 999
will be displayed. The frame counter will continue to count down when the number of recordable
images falls below one thousand.
Camera-shake warning
If the shutter speed falls below the point where the camera can be hand held
safely, the camera-shake warning indicator will appear on the monitor and the
viewfinder indicator lamp will turn green and blink slowly. Camera shake is
slight blurring caused by subtle hand motion and is more pronounced at the
telephoto position of the lens than at the wide-
angle position. Although the warning appears, the
shutter can still be released. If the warning
appears, place the camera on a tripod or use the
built-in flash.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic recording operation
Turn the camera on and slide the mode switch to the recording position.
Place the subject within the focus frame on the LCD monitor or
center the subject in the viewfinder.
• The focus-lock function (p. 24) can be used with off-center
subjects.
• If the subject is closer than 1m (3ft.) at the zoom lens’ wide-angle
position or 3m (10ft) at the telephoto position, only use the LCD
monitor to frame the subject.
Press the shutter-release button partway down (1) to lock the focus
and exposure.
1
• The focus signals (p. 25) on the monitor and the indicator lamp next
to the viewfinder will confirm that the image is in focus. If the monitor
focus signal is red or the indicator lamp
is green and blinks quickly, the camera
was unable to focus on the subject.
2
Repeat the previous steps until the
focus signal is white and the lamp glows
steadily.
Press the shutter-release button all the way down (2) to take the pic-
ture.
• After the shutter releases, the indicator lamp next to the viewfinder
will turn orange and blink indicating image data is being written to
the memory card. Never remove a memory card while data is being
transferred.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING MODE
Focus lock
The focus-lock function is used when you want to compose the image with the subject off-center and
outside the focus frame. Focus lock may also be used when a special focusing situation prevents the
camera from focusing on the subject. This function is controlled with the shutter-release button.
Place the subject within the monitor focus frame or center the
subject in the viewfinder. Press and hold the shutter-release
button partway down to lock the focus.
• The focus signal on the monitor and the
viewfinder indicator lamp will indicate if the
focus is locked.
Without lifting your finger from the shutter-release button,
recompose the subject within the image area. Press the shutter-
release button all the way down to take the picture.
Focus range
The focus range is 25cm (0.8ft.) to infinity. Both the LCD monitor and viewfinder can be used to
frame the subject. However, because of parallax, only the monitor’s live image will be accurate with
subjects closer than 1m (3ft.) at the zoom lens’ wide-angle position or 3m (10ft) at the telephoto posi-
tion.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Focus signals
This digital camera has a quick, accurate autofocusing system. The focus icon in the lower right cor-
ner of the LCD monitor and the indicator lamp next to the viewfinder indicate the focus status. The
shutter can be released regardless of whether the camera can focus on the subject or not.
Focus confirmed - the LCD monitor focus signal is white and the
viewfinder indicator lamp is green and steady.
Cannot focus - the LCD monitor focus signal is red and the
viewfinder indicator lamp is green and blinking quickly. When the
AF system cannot focus, the focus is set to 2m (6.5ft).
Focus signal
Special focusing situations
The camera may not be able to focus in certain situations. In these situations the focus-lock function
(p. 24) can be used to focus on another object at the same distance as your main subject, and then
the image can be recomposed to take the picture.
The subject is too dark. The subject in the
focus frame is low in
contrast.
Two subjects at
different distances
overlap in the focus
frame.
The subject is near a
very bright object or
area.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING MODE
Flash modes
The flash can be used when taking still images. To set the flash
mode, simply press the flash mode button (1) on the back of the cam-
era until the desired mode is displayed. The active flash mode is dis-
played in the top left corner of the LCD monitor. When the camera is
turned off, the flash mode is reset to autoflash with red-eye reduction
if autoflash with red-eye reduction or night portrait was last set, if not
the mode will be reset to autoflash.
1
The flash modes are displayed in the following order:
Night
portrait
Autoflash with
red-eye reduction
Flash
cancel
Autoflash
Fill-flash
Autoflash - the flash fires automatically in low-light and backlit conditions.
Red-eye reduction - the flash fires multiple bursts before the main flash burst to reduce red-eye; an
effect caused by light reflected from the retina. Use in low-light conditions when taking photographs
of people or animals. The pre-flashes contract the pupils of the subject’s eyes.
Fill-flash - the flash fires with each exposure
regardless of the amount of ambient light. Fill-flash
can be used to reduce harsh shadows caused by
strong direct light or sunshine.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Flash cancel - the flash will not fire. Use flash cancel when flash photography is prohibited, natural
light is desired to illuminate the subject, or the subject is beyond the flash range. The camera-shake
warning may appear when flash cancel is selected (p. 22).
Night portrait - for flash portraits at night. The camera automatical-
ly balances the flash and background exposures. When taking por-
traits, ask your subject not to move after the flash burst; the shutter
will still be open for the background exposure. The red-eye reduc-
tion function is used with night portrait. The use of a tripod is
advised in conjuction with this feature.
Flash range
The camera automatically controls the flash output. For well-exposed images, the subject must be
within the flash range. Because of the optical system, the flash range is not the same at the lens’
wide-angle position as it is at the telephoto position.
Wide-angle position
Telephoto position
0.25m ~ 2.9m (0.8 ft. ~ 9.5 ft.)
0.25m ~ 2.3m (0.8 ft. ~ 7.5 ft.)
Flash signals
The indicator lamp next to the viewfinder indicates the status of the
flash. When the lamp is red and blinks quickly, the flash is charging and
the shutter will not release. When the lamp turns green, the flash is
charged and ready to fire.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING MODE
Navigating the recording-mode menu
Camera operations and recording functions are controlled on the menu. Navigating the menu is
simple. The menu button turns the menu on and off. The zoom lever and left and right keys control
the cursor and change settings on the menu. The enter button selects menu options and sets
adjustments.
To activate the recording-mode menu, press the menu button.
The “Basic” tab at the top of the menu will be highlighted. Use the left/right keys to
highlight the appropriate menu tab; the menus will change as the tabs are highlighted.
When the desired menu section is displayed, use the zoom lever to scroll through the
menu options. Highlight the option whose setting needs to be changed.
With the menu option to be changed highlighted, press the right key; the settings will
be displayed with the current setting indicated by an arrow.
• To return to the menu options, press the left key.
Use the zoom lever to highlight the new setting.
• If “Enter” is displayed, press the enter button to display the setting screen.
Press the enter button to select the highlighted
setting.
Basic
Custom Setup 1
Single
Drive mode
Image size
Quality
Once a setting has been selected, the cursor will return to
the menu options and the new setting will be displayed. You
can continue to make function changes. To return to the
recording mode, press the menu button.
1600X1200
Standard
White balance Auto
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic
Custom
Drive mode
Single
Continuous
Self-timer
Movie
Digital zoom
Instant playback
Voice memo
Folder name
On / Off
On / Off
On / Off
Standard form
Date form
Audio rec.
1600 X 1200
1280 X 960
640 X 480
Super fine
Fine
Image size
Quality
Setup 1
LCD brightness
Power off
Enter
1 minute
3 minutes
5 minutes
10 minutes
30 minutes
On / Off
Standard
Economy
Auto
White balance
Daylight
Audio signals
Date/Time set
Date format
Cloudy
Enter
Tungsten
Fluorescent
YYYY/MM/DD
DD/MM/YYYY
MM/DD/YYYY
Refer to the following sections for details on
the menu options and their settings. The setup
1 section can be accessed from both the
recording-mode and playback menu (p. 54).
29
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING MODE
Drive modes
The drive modes control the rate and method images are captured. Icons indicating the selected
drive mode appear on the monitor. The drive mode is selected in the basic section of the recording-
mode menu (p. 28). When the camera is turned off, the drive mode is reset to single-frame advance.
Movie recording (p. 33)
Audio recording (p. 34)
Single-frame advance
Continuous advance (p. 31)
Self-timer (p. 32)
Single-frame advance
Single-frame advance allows only one image to be captured each time the shutter-
release button is pressed. This is the camera’s default setting.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Continuous advance
The continuous-advance drive mode allows a series of images to be captured while
holding down the shutter-release button. The number of images that can be captured at
one time and the rate of capture depend on the image-quality and image-size setting.
With the image-size setting of 1600 X 1200, the maximum rate of capture is 2 fps. If the
image quality is set to super fine (p. 36) only one frame can be captured at a time.
Continuous advance is selected in the basic section of the recording-mode menu (p. 28).
Compose the picture as described in the basic recording operation section (p. 23). Press the shutter-
release button partway down to lock the exposure and focus for the series. Press
and hold the shutter-release button all the way down (1) to begin taking pictures.
1
When the shutter-release button is pressed and held, the camera will begin
recording images until the maximum number has been taken or the shutter button
is released. The built-in flash can be used, but the rate of capture is reduced
because the flash must recharge between frames. The frame
counter is adjusted after the series has been taken while the
images are being saved.
The chart lists the maxi-
mum number of images
that can be captured with
different image-quality and
image-size combinations.
Image
Size
Image
Quality
1600 X 1200 1280 X 960
640 X 480
Fine
Standard
Economy
7
11
23
44
44
81
15
29
140
31
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING MODE
Self-timer
Used for self-portraits, the self-timer will delay the release of the shutter for approxi-
mately ten seconds after the shutter-release button is pressed. The self-timer drive
mode is selected in the basic section of the recording-mode menu (p. 28).
With the camera on a tripod, compose the picture as described in the
basic recording operation section (p. 23). Focus lock (p.24) can be used with off-
1
center subjects. Press the shutter-release button partway down to lock the expo-
sure and focus (1). Press the shutter-release button all the way down to begin the
countdown (2). Because focus and exposure are determined when the shutter-
release button is pressed, do not stand in front of the camera when taking a self-
timer image. Always confirm the focus with the focus signals before beginning the
countdown (p. 25).
2
During the countdown, the self-timer lamp on the front of the
camera (3) will start to blink. A few seconds before the expo-
sure, the self-timer lamp will blink rapidly. The lamp will glow
steadily just before the shutter fires. To stop the countdown,
press the zoom lever. To stop the countdown and cancel the
self-timer, press the main switch. The drive mode will be reset
to single-frame advance after the exposure.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Movie recording
The movie-recording drive mode is selected in the basic section of the recording-mode
menu (p. 28). Movie clips up to approximately thirty-five seconds in length with audio
can be recorded. The movie image is 320 X 240 pixels (QVGA) and recorded at a rate
of around 340KB/s. Approximately one 19-second movie clip can be stored on one
8MB memory card.
Shooting digital video is simple. Frame the picture on the LCD monitor. Press and release the shut-
ter-release button to begin recording (1); “Rec” will be displayed during recording.
The camera will continue to record until the recording time is used or the shutter-
1
release button is pressed again.
When recording, the frame counter will countdown the recording
time. Take care not to cover the microphone while recording.
During recording, focus is locked and the optical zoom is dis-
abled. However, a stepless 2X digital zoom can be used with
the zoom lever.
After recording, a screen will appear indicat-
Stand-by
ing the movie clip is being saved
to the memory card. Never
remove the memory card or dis-
connect the power supply while
the clip is being saved.
Recording
Maximum recording
time for the next clip.
Recording indicator
Saving to card.
Remaining recording time
33
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING MODE
Audio recording
Ninety seconds of audio can be recorded without an image. The audio-recording drive
mode is selected in the basic section of the recording-mode menu (p. 28). When the
function is active, the live view is replaced with a blue screen.
Approximately 842 seconds of audio can be stored on one 8MB memory card. Audio is
recorded at approximately 8KB/s
Microphone
To begin recording, press the shutter-release button
(1). A bar graph (2) will display the amount of
recorded time. The recording will stop when the
shutter-release button is pressed again or the
ninety-second limit has elapsed.
1
When making audio recordings, be careful not to
touch or cover the microphone. The quality of the
recording is proportional to the subject to
Stand-by
microphone distance. For best results, hold the
camera approximately 20cm (8in) from your mouth.
PressShutterButton
ToRecord.
Recording audio.
Press shutter to stop.
2
Recording
Remaining recording time
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Image size
Changing image size affects the number of pixels in
each image. The greater the image size, the larger
the file size. Choose image size based on the final
use of the image - smaller images will be more
suitable for web sites whereas larger sizes will
produce higher quality prints. Image size must be set
before the picture is taken. Image size is set in the
basic section of the recording-mode menu
(p. 28).
Three image sizes are available: 1600 X 1200
(UXGA), 1280 X 960 (SXGA), and 640 X 480 (VGA).
Image size is defined by the image’s horizontal and
vertical dimensions in pixels. The selected image-size
setting is displayed on the LCD monitor by the
horizontal dimension only.
If the image size is changed, the frame counter will display the approximate number of images that
can be recorded at that setting on the installed memory card. One memory card can contain images
with differing sizes.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING MODE
Image quality
This camera has four image-quality settings: super fine, fine, standard, and economy. Always select
the desired setting before taking the picture. Image quality is set in the basic section of the recording-
mode menu (p. 28).
Image quality controls the rate of compression, but has no effect on the number of pixels in the
image. The higher the image quality, the lower the rate of compression and the larger the file sizes. If
the economical use of the memory card is important, use the economy mode. Standard image quality
is sufficient for normal usage. The super-fine mode will produce the highest quality image and the
largest image files.
File formats vary with the image quality setting. Super fine images are saved as a TIFF file. Fine,
standard, and economy images are formatted as JPEG files.
If the image quality is changed, the LCD monitor will display the approximate number of images that
can be recorded at that setting on the installed memory card. One memory card can contain images
with differing qualities.
LCD monitor
File type
display
Super fine - the highest-quality image.
Fine - high-quality image.
S. FIN
FINE
TIFF
JPEG
JPEG
JPEG
Standard - the default setting.
Economy - the smallest file sizes.
STD
ECON
36
Download from Www.Somanuals.com. All Manuals Search And Download.
The frame counter and memory card capacity
The number of images that
Approximate file sizes.
can be stored on a memory
card is determined by the
size and type of card and
the file size of the images.
The actual file size is
determined by the scene;
some subjects can be
compressed further than
others.
Image
size
Image
quality
1600 X 1200 1280 X 960 640 X 480
Super fine
Fine
5.5MB
0.93MB
0.47MB
0.24MB
3.5MB
0.60MB
0.31MB
0.17MB
0.89MB
0.17MB
0.09MB
0.05MB
Standard
Economy
Approximate card capacity for an 8MB memory card.
The frame counter indicates
the approximate number of
images that can be stored
on the memory card at the
camera’s image quality and
size settings. If the settings
Super fine
Fine
1 image
6 images
13 images
25 images
1 image
10 images
20 images
7 images
39 images
68 images
Standard
Economy
39 images 117 images
are changed, the frame counter adjusts accordingly. Because the calculation is based on
approximate file sizes, the actual image taken may not change the counter or may decrease it by
more than one.
When the frame counter displays three red zeros, it indicates no more images at the image size and
quality settings can be captured. Changing the image size or quality settings may allow more images
to be captured.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING MODE
White balance
White balance is the camera’s ability to make different types of lighting appear neutral. The effect is
similar to selecting daylight or tungsten film, or using color compensating filters in conventional pho-
tography.
One automatic and four preset white-balance setting are avail-
able. When one of the preset white-balance settings is selected,
an icon will be displayed on the LCD monitor to indicate the
active white-balance setting. White balance is set in the basic
section of the recording-mode menu (p. 28).
Automatic white balance
The automatic white balance compensates for the color temperature of a scene. In most cases, the
auto setting will balance the ambient light and create beautiful images, even under mixed-lighting
conditions. When the built-in flash is used, the white balance is set for the color temperature of the
flash.
SHOOTING TIPS
White balance cannot correct high-energy vapor lighting: sodium-vapor (yellow highway lights),
or mercury vapor. For portraits under these lighting conditions, the flash can be used to over-
power the ambient light if the subject is within range. With landscapes containing these types of
lights, set the white balance to the preset daylight setting.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Preset white balance
Preset white-balance settings must be set before the image is taken. Once set, the effect is immedi-
ately visible on the monitor.
To record the ambient light, set the flash mode to flash cancel (p. 26). The built-in flash can be used
with preset white-balance, but will create a pinkish or blueish cast with the fluorescent and tungsten
settings. The flash is daylight balanced and will produce good results with the daylight and cloudy
settings.
Daylight - for outdoor and sunlit subjects.
Cloudy - for overcast outdoor scenes.
Tungsten - for incandescent lighting: household filament light bulbs.
Fluorescent - for fluorescent lighting: office ceiling lights.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING MODE
Digital zoom
Assisting the optical zoom is a four-step 2X digital zoom. The digital zoom is activated in the custom
section of the recording-mode menu (p. 28).
The digital zoom increases the magnification of the greatest telephoto setting of the optical zoom in
four steps: X1.25, X1.50, X1.75, and X2.00. Although the images recorded with the digital zoom are
interpolated to the set image size, the quality of the images may not be equal to images taken
without the digital zoom. The effect of the digital zoom is visible on the LCD monitor only. The digital-
zoom function is canceled if the LCD monitor is turned off (p. 48).
Activate the digital zoom in the custom section of
the recording mode menu.
• The digital zoom will remain active until reset
on the menu.
At the maximum telephoto position, press the
zoom lever up to engage the digital zoom.
• The zoom magnification will be displayed in the
top right corner of the monitor.
• To zoom out, press the zoom lever down.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant playback
After a still image is captured, it can be displayed on the
monitor for two seconds before being saved. Instant
playback shows the last frame in the series when used
with the continuous-advance drive mode (p. 31). When
the LCD monitor is turned off (p. 48), it will automatically
activate for the instant playback period.
Instant playback can be activated in the custom section of
the recording-mode menu (p. 28). When used with voice
memo, the audio recording will begin after the image is
played back.
MINOLTA HISTORY
Innovation and creativity has always been a driving
force behind Minolta products. The Electro-zoom X
was purely an exercise in camera design. It was
unveiled at Photokina in Germany in 1966.
The Electro-zoom X was an electronically controlled
aperture-priority mechanical SLR with a built-in 30 -
120mm f/3.5 zoom lens giving twenty 12 X 17mm
images on a roll of 16mm film. The shutter-release
button and battery chamber are located in the grip.
Only a few prototypes were built making it one of
Minolta’s rarest cameras.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING MODE
Voice memo
Voice memo allows an audio track up to fifteen seconds to be recorded with a still image.
The function is activated in the custom section of the recording-mode menu (p. 28). When
the function is active, the white microphone icon is displayed on the LCD monitor. The
voice memo must be set before taking a picture. It will remain in effect until reset. When
the LCD monitor is turned off (p. 48), it will automatically activate for the voice-memo
period.
After an image is captured, a screen will appear
indicating the audio recording has started. A bar
Microphone
2
graph (1) will display the amount of recording
time remaining. To stop the recording, press the
shutter-release button or enter button (2). The
recording will automatically stop when the
fifteen-second limit has elapsed.
Voice memo is attached to the last image of a
continuous-advance series (p. 31). When
played back, images with voice-memo audio
tracks have a note icon displayed with them (p.
51).
When making audio recordings, be careful
not to touch or cover the microphone. The
quality of the recording is proportional to the
subject to microphone distance. For best
results, hold the camera approximately 20cm
(8in) from your mouth.
Recording audio.
Stop
1
Recording
indicator
Remaining recording time
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Folder name
All recorded images are stored in folders on the memory card. Folder names
come in two formats: standard and date.
Standard folders have an eight character name. The initial folder is named
100MLT09. The first three digits are the folder’s serial number, which will increase
by one each time a new folder is created. The next three letters refer to Minolta,
and the last two numbers indicate the camera used; 09 indicates a DiMAGE X.
100MLT09
(Standard)
A date folder name also starts with the three digit serial number and is followed
by one register for the year, two registers for the month, and two registers for the
day: 100YMMDD. The folder 10120412 was created in 2002 on April 12th.
With the date folder format selected, when an image is recorded a new folder
with the day’s date will be created. All images recorded that day will be placed in
that folder. Images recorded on a different day will be placed in a new folder with
the corresponding date. When a new folder is created, the serial number in the
image-file name is reset to 0001. For more information on folder organization and
file names, see page 72.
10120412
(Date)
43
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING MODE
LCD brightness
Low
High
The brightness of the LCD monitor can be set in eleven
levels. After selecting the LCD brightness option and
pressing the enter button on the menu (p. 28, 54), the LCD
brightness screen will be displayed. Pressing and holding
the display button will also active the LCD brightness
screen.
Use the left and right keys (1) to adjust the brightness
level; the monitor image will change accordingly. To set the
level, press the enter button (2); the camera will return to
the recording or playback mode. The LCD brightness level
will affect both modes.
Enter
1
2
Auto-power-off menu settings
To conserve battery power, the camera will shut down if an operation is not made within a certain
period. To restore power, press the main switch. The length of the auto-power-off period can be
changed in the setup 1 section of the recording and playback-mode menu (p. 28, 54): 1, 3, 5, 10,
and 30 minutes. The length of the auto-power-off period is fixed at 10 minutes when the camera is
connected to a computer.
Audio signals
The camera’s audio signals can be turned off and on in the setup 1 section of the recording and
playback-mode menu (p. 28, 54).
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the date and time
It is important to accurately set the clock. When a recording is made, the date and time of the
recording are saved with the file and are displayed in playback mode or with the DiMAGE Image
Viewer Utility software included on the CD-ROM. The date and time are set in the setup 1 section of
the recording and playback-mode menu (p. 28, 54).
When the Date/Time-set option is selected and entered, the
date/time screen will be displayed. The left and right keys (1)
Date/Time set
are used to select the item to be changed and the zoom
lever (2) is used to change the value. From left to right, the
screen shows the year, month, day, hour, and minute. When
the date and time have been adjusted, set the clock by
pressing the enter button (3). The menu button cancels the
screen without applying any changes.
Enter
3
1
2
Setting the date format
The date format that is displayed can be changed: YYYY/MM/DD (year, month, day), MM/DD/YYYY
(month, day, year), DD/MM/YYYY (day, month, year). Simply select the format and enter it by
pressing the enter button; the new format will be displayed on the menu. The date format does not
affect date folder names (p. 43). The date format is set in the setup 1 section of the recording and
playback-mode menu (p. 28, 54).
45
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING MODE
Exposure compensation
The camera exposure can be adjusted to make the final picture lighter or darker by as
much as ±2Ev in 1/3 increments. The exposure-compensation value will remain in effect
until it has been reset or the camera has been turned off.
The exposure compensation must be set before the image is captured. When setting the exposure
compensation, the amount of compensation is shown next to the exposure-compensation icon on the
monitor. When set to any value other than 0.0, the icon will remain on the LCD monitor as a warning.
To set the exposure compensation, the monitor must be on.
1
Use the left and right keys (1) to adjust the
exposure-compensation value.
• The LCD monitor will display the exposure-
compensation icon and value.
• Change in exposure compensation is visible
in the live image on the monitor.
The adjustment in exposure will be
automatically set after five seconds or when
another camera button is pressed.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Sometimes the camera’s exposure meter is deceived by certain subjects. Exposure
compensation can be used in these situations. For example, a very bright scene,
such as a snowy landscape or a white sandy beach, can appear too
dark in the captured image. Before taking the picture, adjusting the
exposure by +1 or +2 Ev will result in an image with normal tonal
values.
In this example, the dark scene appears bright and washed-out on the
LCD monitor. By decreasing the exposure by –1.5 Ev, the richness of
the sunset is preserved.
What is an Ev?
Ev stands for exposure value. A change of one Ev will adjust the exposure calculated by the camera
by a factor of two.
Change in Ev Adjustment to exposure
+2.0 Ev
+1.0 Ev
0.0 Ev
4X as much light
2X as much light
Calculated exposure
1/2 as much light
1/4 as much light
–1.0 Ev
–2.0 Ev
47
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING MODE
Display button - recording mode
The display-information button controls the LCD monitor display. The display cycles to the next
position each time the button is pressed: full display, live image only, and monitor off. If the display
button is pressed and held, the LCD-brightness adjustment screen will appear, see page 44.
Battery power can be conserved by turning the monitor off and using the viewfinder to take pictures.
However, because of parallax, the monitor should be used for subjects closer than 1m (3ft.) at the
zoom lens’ wide-angle position or 3m (10ft) at the telephoto position. When the flash-mode or menu
button is pressed, the monitor will automatically turn on. The digital zoom is disabled when the
monitor is off. The monitor cannot be turned off in audio or movie recording. When the LCD monitor
is off, it will automatically activate for the instant playback period.
Full display
Live image
only
Monitor
off
Display button
48
Download from Www.Somanuals.com. All Manuals Search And Download.
A short guide to photography
Photography can be a rewarding pursuit. This guide is an introduction to some basic photographic
principles.
The zoom lens does not only affect how large the subject is in the picture, but it also influences the
depth of field and perspective. Depth of field is the area between the closest object in focus and the
furthest object in focus. As the lens zooms in (telephoto position) to the subject, the depth of field
becomes shallower, separating the subject from the background. Many portraits are taken with
telephoto lenses. Zooming the lens out to the wide-angle position makes both the foreground and
background appear sharper. Usually
landscape photographs take advantage
of the large depth of field of wide-angle
lenses.
Wide-angle lenses also create a strong
perspective which gives a sense of depth in
the image. Telephoto lenses compress the
space between the subject and background
and create a weak perspective.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK MODE
PLAYBACK MODE
This section details how to view and edit images on the camera. Basic operation of the playback
mode is covered from page 50 to 56. Detailed descriptions of the playback menu settings follow the
menu navigation section.
Single-frame playback display
Mode indicator
Magnification display (p. 53)
Still image
Image size (p. 35)
Image quality (p. 36)
Movie clip
Time of recording
Date of recording
Play
Battery-condition indi-
cator (p. 14)
Audio-track indicator
Print icon (p. 60)
Folder number -
file number (p. 72)
Lock icon (p. 59)
Frame number/
total number of images
Movie icon
An audio recording (p. 34) has no image data and so the LCD monitor will show a blue screen to
indicate the audio file. The time and date of recording, lock status, frame number, and folder and file
number are displayed.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewing images and playing back audio recordings
2
Playing back still images, movie
clips, and audio recordings is
simple. Slide the mode switch to
the playback position (1) and use
the left and right keys to scroll
through the recordings on the
memory card (2).
1
3
A note icon at the bottom of the
monitor indicates the image has an
audio track.
A movie-camera icon at the bot-
tom of the monitor indicates a
movie clip.
To play back the audio track, press the enter
button (3).
To play back the movie clip, press the enter
button (3).
• To cancel a voice memo or audio caption,
press the menu button.
• To pause and restart the movie playback, press
the enter button. Pressing the menu button
cancels the playback.
• To pause and restart an audio recording, press
the enter button. Pressing the menu button
cancels the playback.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK MODE
Display button - playback mode
The display button controls the display format.
Each time the button is pressed, the display
cycles through to the next format: full display,
image only, index playback.
Full display
Display button
Image only
Index playback
In index playback, the left and right keys, and zoom lever moves the yellow border around the index
thumbnails. When the image is highlighted with the border, the date of recording, audio-track
indicator, the lock and printing status, and the frame number of the image are displayed at the
bottom of the screen. The accompanying audio track of the highlighted image can be played by
pressing the enter button. When the display information button is pressed again, the highlighted
image will be displayed in the single-frame playback mode.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Enlarged playback
In single-frame playback, a still image can be enlarged in six steps for closer examination: 1.5X,
2.0X, 2..5X, 3.0X, 3.5X, and 4.0X.
With the image to be magnified displayed, press the zoom lever up to activate
the enlarged playback mode.
• The degree of magnification is displayed on the LCD monitor.
Pressing the zoom lever up increases the image magnification.
Pressing the zoom lever down decreases the image
magnification.
• The display button switches between showing
the full display and image only.
Scroll
To scroll the image, press the enter button.
• Pressing the enter button switches between the enlarged-
playback and scroll screens.
Use the left and right keys, and the zoom
lever to scroll the image.
• To exit the enlarged playback mode, press the
menu button.
Zoom
53
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK MODE
Navigating the playback-mode menu
In playback mode, simply press the menu button to activate the menu. The menu is used to edit
images and control camera operations.
Activate the playback-mode menu with the menu button.
The “Basic” tab at the top of the menu will be highlighted. Use the left/right keys to
highlight the appropriate menu tab; the menus will change as the tabs are highlighted.
When the desired menu section is displayed, use the zoom lever to scroll through the
menu options. Highlight the option whose setting needs to be changed.
With the menu option to be changed highlighted, press the right key; the settings will
be displayed with the current setting indicated by an arrow.
• To return to the menu options, press the left key.
Use the zoom lever to highlight the new setting.
• If “Enter” is displayed, press the enter button to display the setting screen.
Press the enter button to select the highlighted
setting.
Basic
Setup 1 Setup 2
Audio caption
Delete
-
-
-
-
Once a setting has been selected, the cursor will return to
the menu options and the new setting will be displayed.
Changes can continue to be made. To return to the
playback mode, press the menu button.
Lock
Print
Index print
No
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording audio
Basic
Setup 1
Audio caption
Delete
Enter
LCD brightness
Power off
Enter
This frame
All frames
1 minute
3 minutes
5 minutes
10 minutes
30 minutes
On/Off
For information
on the setup 1
section, see
Marked frames
This frame
All frames
Lock
Print
pages 44 to 45.
Marked frames
Unlock frames
This frame
All frames
Audio signals
Date/Time set
Date format
Enter
YYYY/MM/DD
DD/MM/YYYY
MM/DD/YYYY
Number of
copies
Marked frames
Cancel all
Index print
Setup 2
Yes / No
For information on
frame-selection
screens, see page 56.
Format
Enter
Video output
NTSC
PAL
Yes No
Language
Japanese
English
Deutsch
Français
Español
Choosing “Yes” will exe-
cute the operation, “No”
will cancel the operation
Refer to the following sections for descriptions
of the menu options and settings.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK MODE
Frame-selection screen
When a marked-frames setting is chosen on the menu, the frame selection screen will appear. This
screen allows multiple image and audio files to be chosen.
Pressing the zoom
lever up selects the
frame; when
selected, an icon will
appear next to the
frame. Pressing the
zoom lever down
deselects the frame
removing the icon.
The left and right
keys move the
yellow border to
select the frame.
The menu button
cancels the screen
and any operation
made.
Sel.
Confirm Enter
The garbage-can icon indicates the frame is selected for deletion.
The key icon indicates the image or audio file is locked or selected to be locked.
The printer icon indicates the image is selected for printing. The number next to the
icon shows if two or more copies are requested.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio captioning
A still image can have a fifteen-second audio caption attached to it. This function will also replace a
voice-memo audio track recorded with an image. Audio captions cannot be attached to movie clips,
nor can they over rewrite audio recordings.
Display the image to which the audio caption will be attached. If the
image is locked, unlock it using the basic section of the playback menu
(p. 54).
On the playback menu, highlight the “Enter” setting in the
audio-caption option.
Basic
Setup 1 Setup 2
Audio caption
Delete
Enter
Press the enter button (1) to start recording.
• If an audio track is already attached to the image file, a
confirmation screen will appear. Choosing and entering
“Yes” will start the audio caption recording replacing the
previous audio track. “No” will cancel the audio-caption
operation.
Lock
Print
Index print
The audio caption can be stopped during the fif-
teen-second recording period by pressing the
enter button (1).
1
Recording audio.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK MODE
Deleting image and audio files
Deleting permanently erases the image or audio file. Once deleted, a file
cannot be recovered. Care should be taken when deleting files.
Single, multiple, or all image or audio files on the memory card can be deleted with the
playback-mode menu. Before a file is deleted, a confirmation screen will appear;
choosing “Yes” will execute the operation, “No” will cancel the operation.
The delete option has three settings:
This frame - The image or recording displayed or highlighted in playback mode will be deleted.
All frames - All unlocked files on the memory card will be deleted.
Marked frames - To delete multiple image or audio files. When this setting is chosen, the frame-
selection screen will be displayed. Use the left and right keys to highlight the first file to be deleted.
Pressing the zoom lever up will mark the frame with the garbage-can icon. To deselect a file for
deletion, highlight it with the yellow border and press the zoom lever down; the garbage-can icon will
disappear. Continue until all the files to be deleted are marked. Press the enter button to continue (a
confirmation screen will appear), or press the menu button to cancel the operation and return to the
playback menu. On the confirmation screen, highlighting and entering “Yes” will delete the marked
files.
The delete function will only erase unlocked image or audio files. If a file is locked, it must be
unlocked before it can be deleted. If an image file has a voice memo or audio caption attached, both
the image and audio file will be deleted.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Locking image and audio files
Single, multiple, or all image or audio files on the memory card can be locked. A locked
file cannot be erased by a playback menu delete function. Important images should be
locked.
The lock option has four settings:
This frame - The frame displayed or highlighted in playback mode will be locked. If the this-frame
option is used with a locked image, the image will be unlocked.
All frames - All image and audio files on the memory card will be locked.
Marked frames - To lock or unlock multiple files. When this setting is chosen, the frame-selection
screen will be displayed. Use the left and right keys to highlight the image or audio recording to be
locked. Pressing the zoom lever up will mark the frame with the key icon. To unlock a file, highlight it
with the yellow border and press the zoom lever down; the key icon will disappear. Continue until all
the files to be locked are marked. Press the enter button to lock the marked frames, or press the
menu button to cancel the operation and return to the playback menu.
Unlock frames - All files in the folder will be unlocked. When selected, a confirmation screen will
appear; highlighting and entering “Yes” will unlock all files on the card.
Locking an image will protect it from a delete function. However, the formatting function (p. 62) will
erase all data on a memory card whether locked or not.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK MODE
About DPOF
This camera is supported by DPOF version 1.1. DPOF (Digital Print Order Format) allows direct
printing of still images from digital cameras. After the DPOF file is created, the memory card is simply
taken to a photofinishing service or inserted into the card slot of DPOF compatible printers. When a
DPOF file is created, a misc. folder is automatically made on the memory card to store it (p. 72).
Creating a DPOF print order
The print menu option is used to set an order for standard prints from still images on the
memory card. Single, multiple, or all images can be printed.
The print option has four settings:
This-frame - To create a DPOF file for the image displayed or highlighted in playback mode.
All-frames - To create a DPOF file for all still images on the memory card
Marked frames - To chose a group of images to be printed or when the number of copies for each
image varies. When selected, the frame selection screen will appear. Use the left and right keys to
highlight an image to be printed. Pressing the zoom lever up will mark the image with the printer
icon. The number next to the icon indicates the number of copies of that image will be printed.
Pressing the zoom lever up will increase the number of copies, pressing the zoom lever down will
decrease the number. A maximum of nine copies can be ordered. To deselect an image for printing,
press the zoom lever down until the the number of copies reaches zero and the printer icon
disappears. Continue until all the images to be printed are marked. Press the enter button to create
the DPOF file, or press the menu button to cancel the operation and return to the playback menu.
Cancel all - To delete the DPOF print files. When selected, a confirmation screen will appear;
highlighting and entering “Yes” will cancel the print order.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
When the this-frame or all-frames setting is chosen, a screen will appear requesting the number of
copies of each image; a maximum of nine copies can be ordered. Use the zoom lever to set the
number of copies desired. If the all-frames setting was used to create a print order, any additional
images saved afterwards on the memory card will not be included in the order. The print icon is
displayed with selected images in playback mode. If more than one copy of the image is ordered, the
number of copies will be displayed next to the icon.
After the pictures have been printed, the DPOF file will still remain on the memory card. The DPOF
files must be canceled manually. DPOF files cannot be created for images captured with another
camera. DPOF data created on other cameras will not be recognized.
Ordering an index print
To create an index print of all the images on the memory card,
select “Yes.” To cancel an index-print order, simply change the
setting to “No.”
If an index-print order is created, any additional images saved
afterwards on the card will not be included in the index print. The
number of images printed per sheet differs between printers. The
information printed with the thumbnails can vary.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK MODE
Formatting memory cards
When a memory card is formatted, all data on the card is erased.
The formatting function is used to erase all data on a memory card. Before formatting a card, copy
the data to a computer or storage device. Locking images will not protect them from being deleted
when the card is formatted. Always format the memory card using the camera; never use a computer
to format a card.
When the format option is selected and entered, a confirmation screen will appear. Choosing “Yes”
will format the card, choosing “No” will cancel the formatting operation. A screen will appear to
indicate the card has been formatted.
If the unable-to-use-card message appears, the inserted card in the camera may need to be
formatted. A memory card used in another camera may have to be formatted before being used.
Video output
Camera images can be displayed on a television (p. 63). The video output can be changed between
NTSC and PAL. North America uses the NTSC standard and Europe uses the PAL standard. Check
which standard is used in your region to play back images on your television set.
Language
The menu language can be changed.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewing images on a television
It is possible to view camera images on your television. The camera has a AV-out terminal to make
the connection using the supplied AV cable. The camera is compatible with the NTSC and PAL
standards. The video-output setting can be checked and set in the setup 2 section of the playback
menu (p. 54).
1. Turn off the television and the camera.
2. Insert the AV cable into the camera’s AV-out / USB terminal.
3. Plug the other end of the AV cable into the video and audio input
terminals on the television.
• The yellow plug is for the video output. The white plug is for the
monaural audio output.
4. Turn the television on.
2
5. Set the television to the video channel.
6. Turn the camera on and slide the mode switch to the
playback position.
• The camera’s monitors will not activate when the
camera is attached to a television. The playback-mode
display will be visible on the television screen.
7. View images as described in the playback
section.
3
63
Download from Www.Somanuals.com. All Manuals Search And Download.
DATA-TRANSFER MODE
DATA-TRANSFER MODE
Read this section carefully before connecting the camera to a computer. Details on using and
installing the DiMAGE Image Viewer Utility software are found in the supplied software manual. The
DiMAGE manuals do not cover the basic operation of computers or their operating systems; please
refer to the manual supplied with your computer.
DiMAGE X system requirements
For the camera to be connected directly to the computer and used as a mass-storage device, the
computer must be equipped with a USB port as a standard interface. The computer and the
operating system must be guaranteed by their manufacturers to support USB interface. The following
operating systems are compatible with the camera:
IBM PC / AT Compatible
Macintosh
Windows 98, 98SE, Me, 2000
Professional, and XP.
Mac OS 8.6 ~ 9.2.1 and Mac OS X 10.1
Users with Windows 98 or 98 second edition will need to install the driver software on the included
DiMAGE software CD-ROM (p. 67). Users with Mac OS 8.6 will need to download and install a USB
mass-storage device from the Apple web site (p. 70).
Customers who have bought a DiMAGE 7, 5, S304, or 2330 digital camera and have installed the
Windows 98 driver software must repeat the installation procedure. The updated version of the driver
software included on the supplied DiMAGE software CD-ROM is required for the operation of the
DiMAGE X with a computer. The new software will have no affect on the performance of the DiMAGE
7, 5, S304, or 2330.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the camera to a computer
A fully charged battery should be used when the camera is connected to a computer. The use of the
AC adapter (sold separately) is recommended over the use of the battery. For users with Windows
98, 98SE, or Mac OS 8.6, read the respective sections on how to install the necessary USB driver
before connecting the camera to a computer (Windows 98 - p. 67, OS 8.6 - p. 70).
Start up the computer.
• The computer must be turned on before connecting the camera.
1
Insert the memory card into the camera.
• Confirm that the correct card is in the camera. To change the memory card while the camera is
connected to a computer, see page 71.
2
Remove the USB-port cover. Attach the smaller plug of the USB cable to the camera.
• Make sure the plug is firmly attached.
• The USB-port cover is attached to the body to prevent loss.
3
Attach the other end of the USB
4
cable to the computer’s USB
port.
• Make sure the plug is firmly
4
attached.
• The camera should be
connected directly to the
computer’s USB port.
Attaching the camera to a
USB hub may prevent the
camera from operating
properly.
3
(Continued on the next page)
65
Download from Www.Somanuals.com. All Manuals Search And Download.
DATA-TRANSFER MODE
5
Turn on the camera to initiate the USB connection.
• While the camera is connected to a computer, the data-
transfer screen will be displayed.
5
When the camera is properly connected, a drive icon will
appear on the computer. When using Windows XP, the
removable-disk window will be displayed.
If the computer does not recognize the camera, disconnect the camera and restart the computer.
Repeat the connection procedure above. For users with Windows operating systems, the driver
software can be uninstalled in the event of an error during installation. See page 81 for instructions.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to Windows 98 and 98SE
The driver needs only to be installed once. If the driver cannot be installed automatically, it can be
installed manually with the operating system’s add-new-hardware wizard; see the instructions on the
following page. During installation, if the operating system requests the Windows 98 CD-ROM, insert
it into the CD-ROM drive and follow the accompanying instructions on the screen.
Automatic Installation
Before connecting the camera to the
computer, place the DiMAGE software
CD-ROM in the CD-ROM drive. The
DiMAGE installer menu should
automatically activate. To automatically
install the Windows 98 USB driver, click
on the starting-up-the-USB-device-driver-
installer button. A window will appear to
confirm that the driver should be installed;
click “Yes” to continue.
When the driver has been successfully
installed, a window will appear. Click
“OK.” Restart the computer before
connecting the camera (p. 65).
67
Download from Www.Somanuals.com. All Manuals Search And Download.
DATA-TRANSFER MODE
Manual installation
To install the Windows 98 driver manually, follow the instructions in the connecting-the-camera-to-a-
computer section on page 65.
When the camera is plugged into the computer,
the operating system will detect the new device
and the add-new-hardware-wizard window will
open. Place the DiMAGE software CD-ROM in
the CD-ROM drive. Click “Next.”
Choose the recommended search for a suitable
driver. Click “Next.”
Choose to specify the location of the driver. The
browse window can be used to indicate the
driver location. When the location is shown in
the window, click “Next.”
• The driver should be located in the CD-ROM
drive at :\Win98\USB.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
The add new hardware wizard will confirm the
location of the driver. Click “Next” to install the
driver in the system.
• One of three drivers may be located:
MNLVENUM.inf, USBPDR.inf, or USBSTRG.inf.
• The letter designating the CD-ROM drive will
vary between computers.
The last window will confirm the driver has been
installed. Click “Finish” to close the add new
hardware wizard. Restart the computer.
When the my-computer window is opened, a
new removable-disk icon will be displayed.
Double click on the icon to access the camera’s
memory card; see page 72.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
DATA-TRANSFER MODE
Connecting to Mac OS 8.6
To access this camera with a computer with Mac OS 8.6, the USB storage support 1.3.5.smi must be
installed first. This software is supplied by Apple Computer, Inc. free of charge. It can be downloaded
To download and install this software, follow the instruction
on the Apple web site. Always read the attached terms and
conditions before installing any new software.
QuickTime system requirements
QuickTime 5.0 is used for viewing movie clips
and playing audio files. To install QuickTime,
follow the instructions in the installer. Macintosh
IBM PC / AT Compatible
Pentium-based computer
users can download the latest version of
QuickTime free of charge from the Apple
Windows 95, 98, 98SE, NT, Me,
or 2000 Professional.
32MB or more of RAM
Sound Blaster or compatible sound card
DirectX 3.0 or later recommended
Auto power off - data-transfer mode
If the camera does not receive a read or write command within thirty minutes, it will shut down to
save power. When the camera shuts down, an unsafe-removal-of-device warning may appear on the
computer monitor. Click “OK.” Neither the camera or computer will be damaged in this operation.
Unplug the USB cable and turn off the camera. Remake the USB connection by reattaching the
cable and turning the camera on.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the memory card - data-transfer mode
Care should be taken when changing memory cards while the camera is attached to a computer.
Data could be lost or damaged if the camera is not disconnected properly.
Windows 98 and 98SE
1.Disconnect the USB cable.
2.Turn off the camera.
3.Change the memory card.
4.Reconnect the USB cable.
5.Turn on the camera to remake the
USB connection.
Never remove the USB
cable while the viewfinder
indicator lamp is lit!
Windows Me, 2000 professional, and XP
1.Stop the USB connection using the unplug-or-eject-hardware routine (p. 74).
2.Disconnect the USB cable.
3.Turn off the camera.
4.Change the memory card.
5.Reconnect the USB cable.
6.Turn on the camera to remake the USB connection.
Macintosh
1. Stop the USB connection by dragging the drive icon into the trash (p. 75).
2. Disconnect the USB cable.
3. Turn off the camera.
4. Change the memory card.
5. Reconnect the USB cable.
6. Turn on the camera to remake the USB connection.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
DATA-TRANSFER MODE
Memory card folder organization
Once the camera is connected to the computer, image and audio files can
be accessed by double clicking on icons. To copy images and audio
recordings, simply drag and drop the file icon into a location in the
computer.
Drive Icon
Image-file names begin with “PICT” followed
by a four-digit file number and a tif, jpg, mov,
The misc. folder
or thm extension. Voice-memo and audio
contains DPOF print
caption files have a wav extension and the
files (p. 60).
file name corresponds to its image file. Audio
Dcim
Misc
recordings also use the wav extension. The
thumbnail images (thm) are produced with
super-fine images and are only used in
camera operation.
100MLT09
10120801
PICT0003.MOV PICT0004.WAV
PICT0002.JPG
Fine, stan-
dard, or econ-
omy image
PICT0002.WAV
PICT0002’s
voice-memo
or audio-cap-
tion file
PICT0001.TIF
Movie clip
Audio
recording
PICT0001.THM
Super-fine image
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Files and folders on the memory card can be deleted using the computer. Do not change the name
of a file on the card or add a date to the card with a computer. Never format the memory card from
the computer; always use the camera to format the card (p. 54, 62).
The number in the image file name may not correspond to the frame number of the image. As
images are deleted on the camera, the frame counter will adjust itself to show the number of images
in the folder and reassign the frame numbers accordingly. The file numbers will not change when an
image is deleted. When a new image is recorded, it will be assigned a number one greater than the
largest file number in the folder.
When the file number exceeds 9,999, a new folder will be created with a number one greater than
the greatest folder number on the memory card: e.g. from 100MLT09 to 101MLT09. When a DPOF
file is created for a print order (p. 60), a misc. folder is automatically made for the file.
CAMERA NOTES
Image files contain exif tag data. This data includes the time and date the image was recorded
as well as the camera settings used. This data can be viewed with the camera or the DiMAGE
Image Viewer Utility software.
If an image is opened in a image-processing application that does not support exif tag data,
and then the image is saved overwriting the original data, the exif tag information will be
erased. When using software other than the DiMAGE Image Viewer Utility, always rename the
image file to protect the exif tag data.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
DATA-TRANSFER MODE
Disconnecting the camera from a computer
The camera cannot be turned off until the
USB cable is disconnected.
Never remove the USB
cable while the viewfinder
indicator lamp is lit!
Windows 98 and 98SE
Confirm the indicator lamp is not lit.
Disconnect the USB cable and then turn
off the camera.
Windows Me, 2000 professional, and XP
To disconnect the camera, left click on the unplug-or-eject-hardware icon located on
the task bar. A small window will open indicating the device to be stopped.
Click on the small window to stop the
device. The safe-to-remove-hardware
window will appear. Close the window
and then disconnect the USB cable
and turn off the camera.
When more than one external device
are connected to the computer, repeat
the procedure above except right click on the unplug-or-eject-hardware icon. This will open the
unplug-or-eject-hardware window after clicking on the small window indicating the device.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
On the unplug-or-eject-hardware window,
the hardware devices to be stopped will
be displayed. Highlight the device by
clicking on it then click “Stop.”
A confirmation screen will appear to indicate the devices
to be stopped. Clicking “OK” will stop the device.
The safe-to-remove-hardware screen will appear. Click
“OK.” Disconnect the USB cable and then turn off the
camera.
Macintosh
Confirm the indicator lamp is not lit and then drag the mass-storage device icon and drop it into the
trash.
Disconnect the USB cable and turn off the camera.
• If the USB cable is disconnected before performing the first step, an alert message will appear.
Always complete the first step before disconnecting the USB cable.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING THE MENU LANGUAGE
Setting the menu language
1
The menu language is set on the setup 2 section of the playback
menu. Turn the camera on by pressing the main switch near the
shutter-release button (1). Slide the mode switch to the playback
position (2).
2
Press the menu button to active the playback menu.
Use the right key to highlight the setup 2 tab at the
top of the menu.
Use the zoom lever to highlight the language
menu option.
Press the right key. The language settings
will appear on the right side of the menu.
Basic
Setup 1 Setup 2
Format
-
Video output
Language
NTSC
English
Use the zoom lever to select the language.
Press the enter button to set the selected lan-
guage. The playback menu will be displayed.
Playback menu: setup 2 section
Press the menu button to close the playback
menu.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
APPENDIX
This section covers minor problems with basic camera operation. For major problems or damage, or
if a problem continues to reoccur frequently, contact a Minolta service facility listed on the back cover
of this manual.
Problem Symptom
Cause
Solution
The battery is dead.
Recharge the battery (p. 12).
The auto-power-off func-
tion has shut down the
camera.
Turn the camera on using the
main switch.
Nothing dis-
The camera
will not work.
played on the
the monitor.
Check that the adapter is con-
nected to the camera and a
live electrical outlet (p. 15).
The AC adapter is not
connected properly.
The memory card is full Insert a new memory card (p.
and unable to store an 16), delete some images (p.
image at the image-quali- 54), or change the image-qual-
“000” is dis-
played on the
frame counter. ty or image-size setting
on the camera.
ity or image-size setting (p.
28).
Shutter will
not release.
No-card warn-
ing appears
on the moni-
tor.
No memory card in the
camera.
Insert a memory card (p.16).
Card-locked
warning
appears on
the monitor.
Unlock the memory card using
the write-protect switch (p.17).
Memory card is locked.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Problem Symptom
Cause
Solution
Make sure the subject is within
the autofocus range of 25cm
(0.8ft.) to infinity.
Subject is too close.
Focus signal
is red and the
viewfinder
indicator lamp
is green and
blinking quick-
A special situation is pre-
venting the autofocus
system from focusing
(p.25)
Use the focus-lock function to
focus on an object at the same
distance as the subject (p. 24).
ly.
Pictures are
not sharp.
Pictures are
taken indoors
or in low-light
situations with-
out flash.
Slow shutter speeds
result in blurred images
when the camera is
hand-held.
Use a tripod or the built-in flash
(p. 26).
Only one pic-
ture can be
Change the image-quality set-
ting (p. 28).
taken with
continuous
drive.
The image quality is set to super fine.
The subject is beyond the flash range:
flash, the pic- wide-angle position - 0.25m ~ 2.9m (0.8 ft.
While using
Move closer to the subject.
tures are too
dark.
~ 9.5 ft.), telephoto position - 0.25m ~
2.3m (0.8 ft. ~ 7.5 ft.)(p. 27).
78
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Problem Symptom
Cause
Solution
Subject Viewfinder was used for framing. Parallax
appears too is apparent with subjects closer than 1m
far to the right (3ft.) at the zooms’ wide-angle position or
Only use the LCD monitor for
framing with close subjects.
in the image.
3m (10ft) at the telephoto position.
Part of the
Viewfinder
The lens was partially
covered with an object or
finger.
image area is was used to
hidden behind capture the
a dark object. image.
When using the viewfinder,
take care not to cover the lens.
If the camera does not function normally, turn it off, remove and reinsert the battery, or unplug and
reconnect the AC adapter. Always turn the camera off using the main switch otherwise the memory
card may be damaged and camera settings reset.
79
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
The indicator lamp next to the viewfinder can be used to diagnose camera
operations. The lamp colors change between green, red, and orange, and
the lamp can glow steadily or blink at two rates.
Color
State
Steady
Indication
Camera ready to take an image.
Camera-shake warning - shutter speed is below the limit
where the camera can be safely hand-held. Use flash (p. 26)
or tripod.
Blinking
slowly
Green
The camera cannot focus. The subject is closer than 0.25m
(0.8ft.) or a special situation is preventing the autofocus sys-
tem from focusing (p. 25).
Blinking
quickly
Power is insufficient for camera operation.
The flash is charging (while the shutter-release button is
pressed partway down).
Blinking
quickly
Red
The memory card is locked.
The memory card is full.
The memory card cannot be used with the camera and may
need to be formatted.
Blinking
quickly
Orange
The camera is accessing the memory card.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Removing the driver software – Windows
1.Insert a memory card in the camera and connect it to the computer with the USB cable.
Other devices must not be connected to the computer during this procedure.
2.Right click on the My-computer icon. Select “properties” from the drop-down menu.
Windows XP: from the start menu go to the control panel. Click on the performance and
maintenance category. Click “System” to open the system properties window.
3.Windows 2000 and XP: select the hardware tab in the properties window and click the
device-manager button.
Windows 98 and Me: click the device-manager tab in the properties window.
4.The driver file will be located in the universal-serial-bus-controller or other-devices loca-
tion of the device manager. Click on the locations to display the files. The driver should
be indicated with the camera name. Under certain conditions, the driver name may not
contain the camera name. However, the driver will be indicated by either a question
mark or exclamation point.
5. Click on the driver to select it.
6.Windows 2000 and XP: click on the action button to display the drop-down menu.
Select “uninstall.” A confirmation screen will appear. Clicking “Yes” will remove the driv-
er from the system.
Windows 98 and Me: click the remove button. A confirmation screen will appear.
Clicking “Yes” will remove the driver from the system.
7.Disconnect the USB cable and turn off the camera. Restart the computer.
81
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND STORAGE
Camera care
• Do not subject the camera to shock or impact.
• Turn off the camera when transporting.
• This camera is neither waterproof nor splashproof. Inserting or removing the battery or memory
card, or operating the camera with wet hands may damage the camera.
• When at the beach or near water, take care not to expose the camera to water or sand. Water,
sand, dust, or salt can damage the camera.
• Do not leave the camera under direct sunlight. Do not point the lens directly at the sun; the CCD
may be damaged.
• When taking the camera from a cold to a warm environment, place it in a sealed plastic bag to pre-
vent condensation from forming. Allow the camera to come to room temperature before removing it
from the bag.
Memory cards
SD Memory Cards and MultiMediaCards are manufactured with precision electronic components.
The following may cause data loss or damage:
• Improper use of the card.
• Bending, dropping, or subjecting the card to impact.
• Heat, moisture, and direct sunlight.
• Static electrical discharge or electromagnetic fields near the card.
• Removing the card or interrupting the power supply while the camera or a computer is accessing
the card (reading, writing, formatting, etc.).
• Touching the electrical contacts of the card with your fingers or metal objects.
• The disuse of a card for an extended period.
• Using the card beyond its life. Purchasing a new card periodically may be necessary.
The storage capability of the memory card will diminish with extended use. Minolta has no responsi-
bility for any loss or damage to data. It is recommended that a copy of the card data be made.
82
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Batteries
• Battery performance decreases with temperature. In cold environments, we recommend keeping
spare batteries in a warm place, such as the inside of a coat. Batteries can recover their power
when they warm up.
• Do not store the battery when it is fully charged.
• When storing the battery for extended periods, recharge the battery for five minutes every six
months. The battery may not be able to be recharged if completely exhausted.
Cleaning
• If the camera or the outside of the lens is dirty, gently wipe it with a soft, clean, dry cloth. If the
camera or lens comes in contact with sand, gently blow away loose particles. Wiping may scratch
the surface.
• To clean the lens surface, first blow away any dust or sand, then, if necessary, moisten a lens tis-
sue or soft cloth with lens cleaning fluid and gently wipe the lens.
• Never use organic solvents to clean the camera.
• Never touch the lens surface with your fingers.
Storage
• Store in a cool, dry, well-ventilated area away from dust and chemicals. When not in use for long
periods, store the camera in an airtight container with a silica-gel drying agent.
• Remove the battery and memory card from the camera when not in use for extended periods.
• Do not store the camera in an area with naphthalene or mothballs.
• During long periods of storage, operate the camera occasionally. When taking the camera out of
storage, check that the camera is functioning properly before using.
83
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND STORAGE
LCD monitor care
• Although the LCD monitor is manufactured using high precision technology, there may occasionally
be a lack of color or bright points on the LCD monitor.
• Do not apply pressure to the surface of the LCD monitor; it may be permanently damaged.
• In a cold environment, the LCD monitor may become temporarily dark. When the camera warms
up, the display will function normally.
• The LCD monitor may be slow to react in low temperatures or may turn dark in a hot environment.
When the camera reaches normal operating temperature, the display will function normally.
• If fingerprints are on the LCD monitor surface, gently wipe with a soft, clean, dry cloth.
Copyright
• TV program, films, video tapes, photographs, and other materials may be copyrighted.
Unauthorized recording or duplication of such material may be contrary to copyright laws. Taking
pictures or images of performances, exhibitions, etc., is prohibited without approval and can infringe
on copyright. Images protected by copyright can only be used under the provisions within the copy-
right laws.
Before important events or journeys
• Check the camera’s operation; take test pictures and recharge the battery.
• Minolta has no responsibility for any damage or loss incurred by equipment malfunction.
Questions and service
• If you have questions about your camera, contact your local camera dealer or write to the Minolta
distributor in your area.
• Before shipping your camera for repair, please contact a Minolta Service Facility.
84
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
The following marks may be found on the product:
This mark on your camera certifies that this camera meets the requirements of the
EU (European Union) concerning interference causing equipment regulations. CE
stands for Conformité Européenne (European Conformity).
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
Digital Camera:
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
With FCC Standards
Tested To Comply
undesired operation. Changes or modifications not approved by the
party responsible for compliance could void the user's authority to
FOR HOME OR OFFICE USE
operate the equipment. This equipment has been tested and found
to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Tested by the Minolta Corporation 101 Williams Drive, Ramsey, New Jersey 07446, U.S.A.
85
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL SPECIFICATIONS
Number of effective pixels:
CCD:
1.96 million
1/2.7-type interline complementary-color CCD with a
total of 2.11 million pixels.
Automatic (between ISO 100 - 200 equivalent.)
4:3
Camera sensitivity (ISO):
Aspect ratio:
Lens construction:
Maximum aperture:
Focal length:
Focusing range:
Autofocusing system:
Shutter:
Shutter speeds:
Built-in flash recycling time:
Viewfinder:
9 elements in 8 groups.
f/2.8 - f/3.6
5.7 - 17.1 mm (35mm equivalent: 37 - 111 mm)
0.25 m - infinity (from the front of the camera)
Video AF
CCD electronic shutter plus mechanical shutter
2 - 1/1000s
Approximately 6 seconds
Optical real-image zoom viewfinder.
3.8 cm TFT color
Monitor LCD:
Monitor field of view:
A/D conversion:
Recording media:
File formats:
Approximately 100%
12 bits
SD Memory Cards and MultiMediaCards
Exif 2.1 (JPEG, TIFF), motion JPEG (MOV), WAV.
DCF 1.0 and DPOF compliant.
Yes
Japanese, English, German, French, and Spanish
NTSC and PAL
Minolta NP-200 lithium-ion battery.
Print Image Matching:
Menu languages:
Video output:
Battery:
86
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Battery performance (recording): Approximately 120 frames: based on Minolta’s stan-
dard test method: NP-200 lithium-ion battery, LCD
monitor on, full-size images (1600 X 1200), standard
image quality, no instant playback, no voice memo,
flash used with 50% of the frames.
Approximately 190 frames: based on Minolta’s stan-
dard test method: NP-200 lithium-ion battery, LCD
monitor off, full-size images (1600 X 1200), standard
image quality, no instant playback, no voice memo,
flash used with 50% of the frames.
Battery performance (playback): Approximate continuous playback time: 120 min.
Based on Minolta’s standard test method: NP-200
lithium-ion battery, LCD monitor on, no audio play-
back.
External power source:
Dimensions:
Weight:
AC adapter (AC-4 or AC-5)
84.5 (W) X 72.0 (H) X 20 (D) mm
Approximately 135g
(without battery or recording media)
0° - 40°C
5 - 85% (noncondensing)
Operating temperature:
Operating humidity:
Lithium-ion battery NP-200
Voltage:
Weight:
3.7V
20.5g
31.5 (W) X 52.6 (H) X 6.5 (D) mm
Dimensions
Battery charger BC-200
Input voltage:
Weight:
AC100-240V, 50/60Hz
75g
65 (W) X 80 (H) X 25.8 (D) mm
Dimensions
Specifications are based on the latest information available at the time of printing and are subject to
change without notice.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
©2001 Minolta Co., Ltd. under the Berne Convention and the Universal Copyright Convention.
Printed in Japan
Download from Www.Somanuals.com. All Manuals Search And Download.
|