Kenwood Car Stereo System DPX 4010 User Manual

DOUBLE DIN SIZED CD/CASSETTE RECEIVER

DPX-4010

INSTRUCTION MANUAL

AMPLI-TUNER CD/CASSETTE DOUBLE TAILLE

MODE D’EMPLOI

RECEPTOR DE CD/CINTAS DE TAMAÑO DOBLE

MANUAL DE INSTRUCCIONES

Take the time to read through this instruction manual.

Familiarity w ith installation and operation procedures w ill help you obtain the

best performance from your new double din sized CD/cassette receiver.

For your records

Record the serial number, found on the back of the unit, in the spaces designated on

the warranty card, and in the space provided below. Refer to the model and serial

numbers whenever you call upon your KENWOOD dealer for information or service on

the product.

Model DPX-4010 Serial number

Download from Www.Somanuals.com. All Manuals Search And Download.

2Warning

NOTE

2CAUTION

This equipment has been tested and found

to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide

Use of controls or adjustments or

performance of procedures other than those

specified herein may result in hazardous

radiation exposure.

In compliance with Federal Regulations,

following are reproductions of labels on, or

inside the product relating to laser product

safety.

reasonable protection against harmful

interference in a residential installation. This

equipment may cause harmful interference

to radio communications, if it is not installed

and used in accordance with the instructions.

However, there is no guarantee that

interference will not occur in a particular

installation. If this equipment does cause

harmful interference to radio or television

reception, which can be determined by

turning the equipment off and on, the user is

encouraged to try to correct the interference

by one or more of the following measures:

KENWOOD CORPORATION

2967-3, ISHIKAWA-CHO,

HACHIOJI-SHI

TOKYO, JAPAN

KENWOOD CORP. CERTIFIES THIS EQUIPMENT

CONFORMS TO DHHS REGULATIONS N0.21 CFR

1040. 10, CHAPTER 1, SUBCHAPTER J.

Location : Bottom Panel

• Reorient or relocate the receiving antenna.

• Increase the separation between the

equipment and receiver.

FCC WARNING

• Connect the equipment into an outlet on a

circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced

radio/TV technician for help.

This equipment may generate or use radio

frequency energy. Changes or modifications

to this equipment may cause harmful

interference unless the modifications are

expressly approved in the instruction manual.

The user could lose the authority to operate

this equipment if an unauthorized change or

modification is made.

NOTE

This Class B digital apparatus complies with

Canadian ICES-003.

— 3 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Safety precautions

IMPORTANT INFORMATION

2WARNING

2CAUTION

You cannot connect the unit directly to the

following CD automatic changers. If you

want to use older changers with the unit,

follow the directions below according to the

type of changer you own:

To prevent injury or fire, take the

follow ing precautions:

• Insert the unit all the way in until it is fully

locked in place. Otherwise it may fall out of

place when jolted.

• When extending the ignition, battery, or

ground wires, make sure to use automotive-

grade wires or other wires with a 0.75mm²

(AWG18) or more to prevent wire

deterioration and damage to the wire

coating.

• To prevent a short circuit, never put or leave

any metallic objects (such as coins or metal

tools) inside the unit.

To prevent dam age to the m achine,

take the follow ing precautions:

• Make sure to ground the unit to a negative

12V DC power supply.

• Do not open the top or bottom covers of the

unit.

• Do not install the unit in a spot exposed to

direct sunlight or excessive heat or humidity.

Also avoid places with too much dust or the

possibility of water splashing.

• Do not subject the faceplate to excessive

shock, as it is a piece of precision

equipment.

• When replacing a fuse, only use a new one

with the prescribed rating. Using a fuse with

the wrong rating may cause your unit to

malfunction.

English

• KDC-C200 / KDC-C300 / KDC-C400

Use the extension cable and the control box

attached to the CD changer, and the optional

CA-DS100 converter cord.

• KDC-C301 / KDC-C600 / KDC-C800 / KDC-

C601 / KDC-C401

Use the extension cable attached to the CD

changer, and the optional CA-DS100

converter cord.

• KDC-C100 / KDC-C302 / C205 / C705 /

non-Kenw ood CD changers

Cannot be used with this model.

• If the unit starts to emit smoke or strange

smells, turn off the power immediately and

consult your Kenwood dealer.

• Make sure not to get your fingers caught

between the faceplate and the unit.

• To prevent a short circuit when replacing a

fuse, first disconnect the wiring harness.

2CAUTION

You can dam age both your unit and

the CD changer if you connect them

incorrectly.

• Be careful not to drop the unit or subject it to

strong shock.

The unit may break or crack because it

contains glass parts.

• Do not place any object between the

faceplate and the unit.

• Do not use your own screws. Use only the

screws provided. If you use the wrong

screws, you could damage the unit.

• Do not apply excessive force to the moving

faceplate. Doing so will cause damage or

malfunction.

• Do not apply excessive force to the open

faceplate or place objects on it. Doing so will

cause damage or breakdown.

Manufactured under license from Dolby

Laboratories.

“Dolby” and the double-D symbol are

trademarks of Dolby Laboratories.

— 4 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Cleaning the Unit

Cleaning the Tape Head

NOTE

If the front panel gets dirty, turn off the

power and wipe the panel with a dry silicon

cloth or soft cloth.

After you have listened to many cassettes

over a long period of time, magnetic powder

from the tapes and dust accumulates on the

tape head, causing noise and a deterioration

in sound quality. Clean the tape head using a

cleaning tape or cleaning kit designed for use

in car audio systems.

• If you experience problems during

installation, consult your Kenwood dealer.

• If the unit does not seem to be working

right, try pressing the reset button first. If

that does not solve the problem, consult

your Kenwood dealer.

2CAUTION

Do not wipe the panel with a hard cloth or a

cloth dampened by volatile solvents such as

paint thinner and alcohol. They can scratch

the surface of the panel and/or cause the

indicator letters to peel off.

Handling Cassette Tapes

• Do not play a cassette whose tape has gone

slack. In such a case, wind it tight using a

pencil or the like in one of the spools.

Playing slack cassette tapes can result in the

tape tangling around the capstan and/or

pinch rollers, causing trouble.

• Do not play a deformed cassette or one

whose label is starting to come off, as it can

cause the unit to malfunction.

• Do not leave tapes in hot places, such as on

dashboards and other spots exposed to

direct sunlight, or near heater outlets. They

can deform the cassette.

• Avoid using extremely long cassette tapes,

such as 100-minute-long tapes. Such tapes

are very thin, and can tangle easily around

the pinch rollers or other parts inside the

unit, causing unit failure.

Cleaning the CD Slot

As dust tends to accumulate in the CD slot,

clean it every once in a while. Your CDs can

get scratched if you put them in a dusty CD

slot.

Reset button

• The illustrations of the display and the panel

appearing in this manual are examples used

to explain more clearly how the controls are

used. Therefore, what appears on the display

in the illustrations may differ from what

appears on the display on the actual

equipment, and some of the illustrations on

the display may represent something

impossible in actual operation.

Lens Fogging

• Remove a cassette tape from the unit when

not listening to it for a while. If you leave a

tape in the unit too long, it may stick to the

tape head and cause unit malfunction.

• The functions that can be used and the

information that can be displayed will differ

depending on the external disc players being

connected.

Right after you turn on the car heater in cold

weather, dew or condensation may form on

the lens in the CD player of the unit. Called

lens fogging, CDs may be impossible to play.

In such a situation, remove the disc and wait

for the condensation to evaporate. If the unit

still does not operate normally after a while,

consult your Kenwood dealer.

— 5 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Handling Com pact discs

listening to them for a while, and put them

back in their cases. Do not pile up CDs that

are removed from their cases or prop them

against something.

Playing a CD that is dirty, scratched

or w arped can cause the sound to

skip and the unit to operate

incorrectly, resulting in w orsened

sound quality. Take the follow ing

precautions to prevent your CDs from

getting scratched or dam aged.

Rem oving the CD

Only remove the CD from the machine in a

horizontal direction, holding it flat. You may

damage the surface of the CD if you try

pulling it down as it ejects.

English

Cleaning CDs

If a CD has gotten dirty, wipe it off gently

using a commercially available cleaning cloth

or a soft cotton cloth, starting from the

center of the disc and moving outward. Do

not clean CDs with conventional record

cleaners, anti-static formulas, or chemicals

such as paint thinner or benzene.

Handling CDs

• Do not touch the

recorded side of the CD

(the side opposite the

label) when holding it.

Do Not Use Special Shape CDs

• Be sure to use round shape CDs only for

this unit and do not use any special shape

CDs. Use of special shape CDs may cause

the unit to malfunction.

• The reflective film on a CD-R or a CD-RW is

more fragile than that on an ordinary music

CD, and may peel off if scratched.

Fingerprints on a CD-R or CD-RW are also

more likely to cause skipping when the disc

is played. For these reasons, handle the disc

very carefully.

Detailed handling instructions will appear on

the CD-R or CD-RW package: read this

information carefully before using the disc.

Checking New CDs for Burrs

When playing a new CD for the first time,

check that there are not any burrs stuck to

the perimeter of the disc or in the central

hole. CDs with burrs stuck on them may not

load properly or may skip while playing.

Remove burrs using a ballpoint pen or a

similar utensil.

• Do not use any CD which does not bear one

of the following marks:

CD-Rs and CD-RWs which have not

undergone finalization processing cannot be

played. (For more information on finalization

processing, refer to the manual for your CD-

R or CD-RW writing software.) Additionally,

depending on the recording status, it may

prove impossible to play certain CDs

recorded on CD-R or CD-RW.

Tape

• Do not stick tape on

either side of the CD.

Burrs

Storing CDs

• Do not store CDs in areas exposed to direct

sunlight (such as a car seat or the

Burrs

dashboard) or other hot places.

A CD-R or CD-RW is more susceptible than

a music CD to damage from high

temperatures and humidity, and in some

cases, may become unusable if left in the

car for long periods of time.

Do Not Use CDs w ith Sticker on the

Labeled Side

Do not use the CD with the label sticker

stuck on it.

Using such a CD may cause the CD to be

deformed and the sticker to peel off,

resulting in malfunction of the unit.

Do Not Load CD Accessories

Do not use commercially available CD

accessories that can be loaded into the CD

slot, such as stabilizers, protective sheets,

or CD cleaning discs, since they can cause

the unit to malfunction.

• Remove CDs from the unit when not

— 6 —

Download from Www.Somanuals.com. All Manuals Search And Download.

General features

P o w e r

Turning on the pow er:

Press the SRC (source) button.

NOTE

Turn the power on before carrying out the following procedures.

CD EJECT

OPEN

Turning off the pow er:

Press the PWR OFF button for at least one second.

NAME SET

DISP

ATT

Vo lu m e

FM+

Increasing Volum e:

S.A

DISC

PWR OFF

B.S

METAL

AUD

FNC

Press the u button to turn up the volume.

SRC

AM–

DSP

BNR

SCN

RDM

REP

D.SCN

M.RDM

Decreasing Volum e:

SRC/

PWR OFF

Press the d button to turn down the volume.

AUD

ATT indicator

Clock display

At t e n u a t o r

This function allows you to turn down the volum e quickly.

Turning Attenuator On/ Off:

Press the ATT button to switch the attenuator on and off.

When the attenuator is on, the ATT indicator blinks.

When the attenuator is off, the volume returns to the original

level.

NOTE

Turning the volume up, or turning it all the way down deactivates

the attenuator function.

— 7 —

Download from Www.Somanuals.com. All Manuals Search And Download.

General features

S w it c h in g Mo d e s

Au d io Co n t ro l S e t t in g

Adjust various param eters of sound quality.

Sw itching Modes:

Each time you press the SRC (source) button, the mode

switches as follows:

Press the AUD button for at least one second to enter the

control mode.

English

▼

Selecting m ode

Tuner mode

Press either the 4 or ¢ button.

Each time the button is pressed, the adjustment mode will

change.

Please refer to the following for the contents of the

adjustment modes.

▼

Tape mode

▼

CD mode

▼

External disc control mode 1

▼

Adjust each m ode

Press the FM/AM button.

Please refer to the following for the adjusting values.

External disc control mode 2/AUX mode

▼

Standby mode

Press the AUD button for at least one second to end the

control mode.

Selecting standby m ode:

Press the SRC button repeatedly and switch to "ALL OFF" .

When "ALL OFF" is displayed, the standby mode is activated.

The standby mode turns all functions off while leaving the

power to the unit on. Use this mode when you want to have

the display illuminated but don't want to listen to anything.

"Balance" : Adjust the balance level.

Setting values: Left 15 – Right 15

NOTE

• The mode switches to the next mode from any mode which

cannot be used.

• The external disc control mode will differ depending on the unit

that is connected.

• The AUX mode is available only when the changer / AUX

switching adapter (KCA-S210A or CA-C1AX) or CD changer

(KDC-CPS85, KDC-CX85, KDC-CPS82 or KDC-CX82) is

connected to this unit.

"Fader" : Adjust the fader level.

Setting values: Front 15 – Rear 15

During the AUX mode, "AUX INPUT" will show in the display.

When the CA-C1AX is being used, the AUX Mode will replace

the External Disc Control Mode.

"NON FAD" : You can set the non-fading sound output to either

on or off.

Setting values: "NON FAD On" (ON) – "NON FAD Off" (OFF)

NOTE

This mode is available only when the non-fading output function

is set to on.

— 8 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Tuner features

S w it c h in g Dis p la y

You can switch the display during the standby m ode as

m entioned below.

Changing the Display:

Each time you press the DISP button, the display changes as

follows:

CD EJECT

OPEN

▼

NAME SET

DISP/

NANE SET

Character + Graphic

DISP

▼

ATT

Clock + Graphic

▼

Clock

FM+

S.A

DISC

PWR OFF

B.S

METAL

AUD

FNC

SRC

AM–

DSP

BNR

SCN

RDM

REP

D.SCN

M.RDM

Ad ju s t in g Tim e

Adjust the tim e.

SRC

#1-6

Band display

When the time is not displayed, first press the DISP button to

display the time.

Preset station number

Press the DISP button for at least one second to enter the

clock adjustment mode.

Frequency

AUTO indicator

• Adjusting the hours

Press the FM button to advance the hours, or press the AM

button to make the hours go back.

• Adjusting the minutes

Press the ¢ button to advance the minutes, or press the

4 button to make the minutes go back.

Press the DISP button to end the clock adjustment mode.

ST indicator

— 9 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Tuner features

Tu n in g

Select the band/ station that you want to have stored.

Press the button (#1-6) that you want to use for the station, for

at least two seconds.

The button number blinks once in the display to indicate that

the data has been stored.

Press the SRC (source) button repeatedly to select the tuner

mode. "TUNER" is displayed when the tuner mode has been

selected.

English

Press either the FM or AM button to select the band.

Each time you press the FM button, the band switches

between the FM1, FM2 and FM3.

Recalling a Preset Station:

Press the preset station button (#1-6) for the desired station.

The number of the recalled station is displayed.

Press the AM button to select the AM band.

NOTE

• Auto Seek Tuning

You can store six stations in each of the FM1, FM2, FM3, and

AM bands.

Press the ¢ button to seek higher frequencies.

Press the 4 button to seek lower frequencies.

• Preset station seek tuning

Press the ¢ button to move to the next preset station (i.e.,

the one with the next highest number), and the 4 button to

move to the last preset station (i.e., the one with the next

lowest number).

S t a t io n Na m e P re s e t (S NP S )

You can assign nam es to radio stations with the Station Preset

Mem ory. Up to 30 stations can be assigned nam es.

NOTE

If the frequencies stored at the preset numbers receive

stations which were not originally memorized when traveling

long distances, the preset number is not displayed. In such

cases, pressing the 4/¢ button to use preset station

seek will receive channel 1.

Adjust the frequency to the station whose name you want to

enter.

NOTE

This function cannot be available during the clock display.

• Manual Tuning

Press the ¢ button to increase the frequency by one step.

Press the NAME.S button for at least two seconds.

"Name Set" is displayed once the station name preset mode is

entered.

Press the 4 button to decrease the frequency by one step.

NOTE

The cursor will blink in the position where letters are entered.

• Please see the Function Set System about selecting tuning

mode. (page 25)

• The ST indicator lights up when stereo broadcasts are being

received.

Press either the 4 or ¢ button to move the cursor to the

desired position.

The 4 button moves the cursor to the left, and the ¢

button to the right.

Each time the 38 button is pressed, the characters to be

entered change as listed below.

Press the FM or AM button to display the desired character.

Characters that can be displayed are as follows.

S t a t io n P re s e t Me m o ry

Store the frequency of a station. You can then recall that

station with a single touch of a button.

— 10 —

Download from Www.Somanuals.com. All Manuals Search And Download.

S w it c h in g Dis p la y fo r Tu n e r

You can change the display used when listening to the radio.

Alphabet (upper case)/Numerals/Symbols:

A ~ Z 0~9 / + – *= < > []

Changing the Display:

Alphabet (lower case)/Numerals/Symbols:

Each time you press the DISP button, the display changes as

follows:

a ~ z 0~9 / + – *= < > []

Continue steps 3 and 4 until all the characters are chosen for

the name.

Station frequency

SNPS name (only when being preset)

Character

NOTE

You can enter up to 8 characters for each name.

Assigning Nam es

Press the NAME.S button.

Clock

The name of the station is stored in memory, and the Station

Name Preset mode ends.

Also, if you make no input for 10 seconds, the name will be

stored up to the point that you have entered, and the mode

ends.

NOTE

• You can assign names to up to 30 FM/AM stations in all.

If you try to enter more than that, the station name stored the

earliest will be the first one erased.

• If you want to change the name of a station, first display the

name of the station (following steps 1 and 2 above), then

change the letter(s) that you want by following steps 3 and 4.

— 11 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Cassette player features

P la yin g Ca s s e t t e Ta p e s

Loading and Playing Cassettes:

A press of the OPEN button results in the faceplate dropping

open to the front, thereby exposing the cassette insertion slot.

Holding the cassette with the tape exposed to the right, insert

it in the slot. The tape will start playing.

Push back on the right side of the faceplate with your hand

until it locks.

English

CD EJECT

OPEN

NAME SET

DISP

The

indicator lights up when a cassette has been loaded.

ATT

2CAUTION

When inserting a cassette make sure the cassette has been

completely drawn in before pushing back the faceplate. Failing to

do so might deform the tape.

FM+

S.A

DISC

PWR OFF

B.S

METAL

AUD

FNC

SRC

AM–

DSP

BNR

SCN

RDM

REP

D.SCN

M.RDM

SRC

METAL

B NR

B.S

REP

SCN

Mode display

Tape counter display

indicator

SCN indicator

0 button

Playing Cassettes Already Loaded:

Press the SRC (Source) button repeatedly to select the tape

mode.

"TAPE" is displayed when the tape mode has been selected.

The tape will start playing.

Listening to the other side:

Press the 38 button.

B.S indicator

MTL indicator

B NR indicator

REP indicator

Tape play switches to the other side.

Ejecting Cassettes:

Press the OPEN button and drop open the faceplate.

Press the 0 button located near the cassette insertion slot.

The tape stops playing and the cassette ejects.

Push back on the right side of the faceplate with your hand

until it locks.

— 12 —

Download from Www.Somanuals.com. All Manuals Search And Download.

2CAUTION

S w it c h in g Ta p e Typ e s

• When the faceplate has been dropped open, it might interfere

with the shift lever or something else. If this happens, pay

attention to safety and move the shift lever or take an

appropriate action, then operate the unit.

• Do not apply excessive force to the open faceplate or place

objects on it. Doing so will cause damage or breakdown.

• Do not use the unit with the faceplate in the open condition.

Doing so will cause breakdown.

Select type of tape being played.

Sw itching Tape Types:

Press the METAL (Metal) button to switch the metal tape

indicator on and off and to select the tape type.

Turn the MTL indicator off for normal tape (Type I) playback.

Turn the MTL indicator on for the following tape types:

CrO (Type II) FeCr (Type III) Metal (Type IV)

Selecting the wrong tape type may cause sound quality to

suffer.

NOTE

Remove a cassette from the unit when not listening to it for a

while. If you leave it in the unit too long, the tape may stick to

the tape head and cause the unit to malfunction.

Ta p e c o u n t e r d is p la y

Sw itching the Tape display :

Each time you press the DISP button, the display during tape

play switches as follows:

Fa s t Fo rw a rd in g a n d Re w in d in g Ca s s e t t e Ta p e s

Fast Forw arding Tapes:

Press the FM button.

Play side/Tape counter

Character

Rew inding Tapes:

Press the AM button.

Canceling:

Clock

Press the 38 button.

Normal tape play will begin.

NOTE

The tape counter is not exact, but only represents an

approximation of the elapsed time.

Us in g Do lb y B No is e Re d u c t io n

Listen to tapes recorded using Dolby B NR.

Turning Dolby B Noise Reduction On/ Off:

Press the B NR button to switch Dolby B NR on and off.

The B NR indicator lights up when it is turned on.

— 13 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Cassette player features

Us in g Dire c t P ro g ra m S e a rc h S ys t e m (DP S S )

Bla n k S k ip

Skip forward or backward to other tracks during playback.

Autom atically fast forwards to the beginning of the next track

when long blank spaces (10 seconds or m ore) are detected,

continuing tape playback. This function is on, when unit is first

powered on.

Skipping to Beginning of Current Track or to Previous Tracks

(Rew ind DPSS):

English

Press the 4 button.

Turning Blank Skip Function On/ Off:

Press once to rewind to the beginning of the current track,

twice to rewind to the beginning of the previous track, and so

forth.

Press the B.S button to switch the blank skip function on and

off.

"B-SKIP On" is displayed when the blank skip function is turned

on.

You can skip up to nine tracks.

Playback is continued after the tape is rewound by the

indicated number of tracks.

NOTE

Skipping to Later Tracks (Fast Forw ard DPSS):

Press the ¢ button.

• If the blank space contains much noise, the blank skip function

may not work right.

• Sections recorded at low levels may trigger the blank skip

function if they last for 10 seconds or more.

Press once to fast forward to the next track, twice to fast

forward to the track after that, and so forth.

You can skip up to nine tracks.

Playback is continued after the tape is fast forwarded by the

indicated number of tracks.

NOTE

In d e x S c a n

• During the first five seconds of each track, the previous track is

considered the "current" track. If you press the 4 button

during that period, the tape rewinds to the beginning of the

previous track and not the one you are listening to.

Successively plays the first few seconds of each track on the

tape.

Turning Index Scan On/ Off:

• The DPSS function "knows" where a track begins by detecting

the blank space preceding it (the space between tracks).

However, when the blank space lasts for less than four

seconds or contains noise, DPSS may not operate correctly.

Furthermore, quiet intervals within a song are detected as

"blank spaces" if they last for four seconds or more.

Press the SCN button to switch index scan on/off.

The SCN indicator lights up when index scan is turned on.

Stopping to Listen to the Track Being Scanned:

Press either the SCN or 38 button.

Playback begins as usual.

NOTE

Canceling DPSS While It Is Operating:

• Index scan is canceled when the tape stops.

Press the 38 button.

• Index scan "knows" where a track begins by detecting the blank

space preceding it (the space between tracks). However, when

the blank space lasts for less than four seconds or contains

noise, this function may not operate correctly. Furthermore,

sections that are recorded at low levels may trigger the function

if they last for four seconds or more.

— 14 —

Download from Www.Somanuals.com. All Manuals Search And Download.

CD/ External disc control features

Mu s ic Re p e a t

Repeatedly plays the track currently being listened to.

Turning Music Repeat On/ Off:

Press the REP button to switch music repeat on/off.

"Repeat On" is displayed when music repeat is turned on.

CD EJECT

OPEN

Canceling Music Repeat:

Press either the REP or 38 button.

NOTE

NAME SET

DISP/

NAME SET

DISP

ATT

Music repeat "knows" where a track begins by detecting the

blank space preceding it (the space between tracks). However,

when the blank space lasts for less than four seconds or contains

noise, this function may not operate correctly. Furthermore,

sections that are recorded at low levels may trigger the function

if they last for four seconds or more.

FM+

S.A

DISC+

DISC-

DISC

PWR OFF

B.S

METAL

AUD

FNC

SRC

AM–

DSP

BNR

SCN

RDM

REP

D.SCN

M.RDM

SRC

RDM D.SCN

SCN REP M.RDM

CHANGER indicator

Track time

Track

number

Mode display/

Disc number

SCN/D.SCN indicator

REP/D.REP indicator

RDM/M.RDM indicator

indicator

— 15 —

Download from Www.Somanuals.com. All Manuals Search And Download.

CD/ External disc control features

• Regardless of the control unit, the characters that can be

registered with the Presetting Disc Names function are "A~Z

0~9 /, +, –, ∗, =, <, >, [ , ]".

P la yin g CDs

Playing CDs:

• The disc name will be displayed when the name has been

registered to the playing unit with the Presetting Disc Names

function.

If no CDs are inserted, insert one in the slot with the label

facing up.

If a CD is already inserted, press the SRC button repeatedly to

select the CD mode.

English

NOTE

"CD" is displayed when the CD mode has been selected.

The CD will start playing.

The CD text, Presetting Disc Names, and Disc Name Preset Play

functions may not be operational depending on the unit.

The

indicator lights up when a CD has been inserted.

Pausing and Restarting CD Play:

Press the 38 button to make the disc pause.

Press the same button again to start play again.

P la yin g Ot h e r Dis c m o d e

This function perm its the connection of optional players and

the playing of discs other than the loaded CD (in the current

unit).

Stopping and Ejecting CDs:

Press the 0 button.

The CD stops playing and ejects from the slot.

2CAUTION

Playing Discs:

Do not attempt to insert a CD into the slot if another one is

already there.

Press the SRC button repeatedly to select the external disc

control mode.

The disc will start playing.

NOTE

When you load a CD and eject it right away, the next time you try

to insert the CD may not load. In such a situation, take the CD

out for a moment and then reinsert it.

NOTE

The external disc control mode will differ, depending on the unit

that is connected.

Mode Display Examples

• "DISC-CH" ...when a disc changer is connected

• "DISC-CH1" , "DISC-CH2" ...when two disc changers are

connected

■ When a unit equipped with an O-N switch is to be

connected, please also see the instruction m anual of this

unit.

Pausing and Restarting Disc Play:

Press the 38 button to make the disc pause.

Set the O-N switch to "N". "N"-operation will be set.

Press the same button again to start play again.

"N"-operation:

NOTE

• The disc title and track title of the CD text can be displayed.

• The disc name will be displayed when the name has been

registered to any connected unit with the Presetting Disc

Names function, or when the playing unit contains a disc to

which the disc title has been recorded.

When one disc has finished playing its last track, the next disc in

the changer will start playing. When the last disc in the changer

has finished, the player will return to the first disc and start

playing it.

"O"-operation:

• CD text cannot be displayed.

— 16 —

Download from Www.Somanuals.com. All Manuals Search And Download.

S w it c h in g Dis p la y fo r Dis c s

Fa s t Fo rw a rd in g a n d Re ve rs in g Dis c P la y

Switch the display that appears while discs are playing.

Fast Forw arding Disc Play:

Hold down on the ¢ button.

Sw itching Display for Discs:

Release your finger to play the disc at that point.

Each time you press the DISP button, the display during disc

play switches as follows:

Reversing Disc Play:

Hold down on the 4 button.

Release your finger to play the disc at the point.

Track time

NOTE

Total disc playing time (CD only)

Disc name (DNPS) (CD only)

Disc title* (Units featuring CD text/MD only)

Track title* (Units featuring CD text/MD only)

Character

You cannot use reverse play between tracks depending on the

model being connected. Instead, the reverse play function is

canceled when it reaches the beginning of a track, at which point

normal play will automatically resume.

Clock

(*: For disc changers)

NOTE

• You can give names to discs through the presetting disc name

function (see p. 21).

Note that depending on the unit, display may not be possible.

• If you try to display the name of a disc that doesn't have one,

"No Name" is displayed instead.

• When an attempt is made to display the title of a disc for which

a disc title/track title has not been recorded, the CD will display

"No Text" , and an MD changer will display "No Title".

• Depending on the type of characters of the CD Text, some

characters may not be displayable.

— 17 —

Download from Www.Somanuals.com. All Manuals Search And Download.

CD/ External disc control features

Play starts at the beginning of the displayed disc.

Tra c k S e a rc h

Search forward or backward through the tracks on the disc

until you reach the one that you want to listen to.

NOTE

"LOAD" is displayed when discs are being exchanged on the disc

changer.

English

Making a Reverse Track Search:

Press the 4 button to display the desired track number.

Press once to search back to the beginning of the current

track, twice to search back to the beginning of the previous

track, and so forth.

Tra c k Re p e a t

Repeat playing the track currently being listened to.

Play starts at the beginning of the displayed track number.

NOTE

(For disc changers)

Turning Repeat Play On/ Off:

Pressing the 4 button while listening to track 1 will only search

back to the beginning of that track. The reverse search is not

"recycled" to the last track on the disc.

Press the REP button to switch repeat play on and off.

The REP indicator lights up when repeat play is turned on.

The track number currently being heard blinks in the display.

Making a Forw ard Track Search:

NOTE

Press the ¢ button to display the desired track number.

Press once to fast forward to the next track, twice to fast

forward to the track after that, and so forth.

Repeat play is canceled when you eject the disc.

Play starts at the beginning of the displayed track number.

NOTE

(For disc changers)

Dis c Re p e a t

Repeat playing the disc currently being listened to.

(Function of disc changers)

You cannot make a forward track search when listening to the

last track on a disc.

Turning Disc Repeat Play On/ Off:

Press the REP button for at least one second to switch disc

repeat play on and off.

The D.REP indicator lights up when disc repeat play is turned

on. The disc number currently being heard blinks in the display.

Dis c S e a rc h

Search forward or backward through the discs in a disc

changer.

(Function of disc changers)

NOTE

Repeat play is canceled when you stop playing the disc.

Making a Reverse Disc Search:

Press the DISC– button to display the desired disc number.

Each time the button is pressed, the displayed disc number

decreases by one.

Play starts at the beginning of the displayed disc.

Making a Forw ard Disc Search:

Press the DISC+ button to display the desired disc number.

Each time the button is pressed, the displayed disc number

increases by one.

— 18 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Tra c k S c a n

Successively play the beginning of each track on a disc until

you find the track that you want to listen to.

Starting the Track Scan :

Press the SCN button. "Track Scan" is displayed and the first

10 seconds of each track will be played, in order.

The track number currently being heard blinks in the display.

Stopping to Listen to the Track Being Scanned:

Press the 38 or SCN button again to stop the scan and keep

on listening to a track normally.

NOTE

• The track scan function is canceled when you eject the disc.

• The track scan function only scans each track on a disc once.

Dis c S c a n

(Function of disc changers)

Successively play the beginning of each disc on a changer

until you find the one that you want to listen to.

Starting the disc scan:

Press the D.SCN button. "Disc Scan" is displayed and the first

10 seconds of each disc will be played, in the order they are

loaded on the changer.

The disc number currently being heard blinks in the display.

Stopping to Listen to the Disc Being Scanned:

Press the 38 or D.SCN button again to stop the scan and keep

on listening to the disc normally.

NOTE

• The disc scan function is canceled when you eject the disc.

• The disc scan function only scans each disc on the changer

once.

• "LOAD" is displayed when discs are being exchanged on the

disc changer.

— 19 —

Download from Www.Somanuals.com. All Manuals Search And Download.

CD/ External disc control features

• Magazine random play is canceled when you eject the disc.

• The time needed for random selection depends on the number

of discs loaded in the disc magazine.

Ra n d o m P la y

Play all the tracks on the current disc in random order.

Press the RDM button to switch random play on and off.

"Random" is displayed when random play is turned on.

The track number will change over and over in the display as

the next track is being selected.

English

Te xt / Tit le S c ro ll

This function perm its the text to be scrolled and the entire text

to be displayed. The scrolling m ethod differs depending on the

setting of scrolling in the function set.

(Function of disc changers)

When the track has been selected, play will begin.

NOTE

(For disc changers)

When all the tracks on a certain disc have been played using

random play, the next disc on the changer will start playing using

the same function.

To scroll autom atically:

Press the DISP button to display the disc title or the track title.

The display of the text will be scrolled repeatedly.

To change the track being heard, press the ¢ button.

Another track will be selected and played.

To scroll m anually:

NOTE

Press the DISP button to display the disc title or the track title.

Random play is canceled when you eject the disc.

Press the 1 button.

The display of the text will be scrolled once.

NOTE

• Please see the Function settings (page 26) about switching

between manual scrolling and automatic scrolling.

• Only units with a CD text feature permit title display.

Ma g a zin e Ra n d o m P la y

Play the tracks on all the discs in the disc changer in random

order.

(Function of disc changers)

Press the M.RDM button to switch magazine random play on

and off.

"M-Random" is displayed when magazine random play is turned

on.

The disc and track numbers will change over and over in the

display as the next track is being selected.

When the disc/track has been selected, play will begin.

NOTE

This function is not available with the following models:

KDC-C200/C300/C400/C301/C401

To change the track being heard, press the ¢ button.

Another disc/track will be selected and played.

NOTE

— 20 —

Download from Www.Somanuals.com. All Manuals Search And Download.

as this, and the characters to be input are selected using the

procedure described below.

Press the DISC+ or DISC– button to display the desired

character. Besides the alphabet (capital letters only) and

numbers, you can choose the following characters: /, +, –, ∗,

=, <, >, [ and ].

P re s e t t in g Dis c Na m e s (DNP S )

Store the nam es of discs to be displayed when played.

Play the disc whose name you want to preset.

NOTE

• This function is available only for the CD player of this unit and

disc changers that feature the Disc Name Preset function.

• This procedure is not to be used to store the disc and track

titles for MDs that you record.

• This function cannot be available during the clock display and

while using disc scan or magazine random play.

Continue steps 3 and 4 until all the characters are chosen for

the name.

NOTE

You can enter up to 8 characters for each name.

Press the NAME.S button.

The disc name is stored and the disc name preset mode is

canceled.

Press the NAME.S button for at least two seconds.

"Name Set" is displayed and the disc name preset mode is

If you make no entry in a 10-second period, the name will be

stored with the characters input so far.

entered.

The cursor blinks in the position where character input can be

made.

NOTE

Press either the 4 or ¢ button to move the cursor to the

desired position.

• The number of discs whose names can be stored will differ

depending on the disc changer that is connected. Please see

your disc changer manual for details.

Up to 10 CDs can be registered with this unit.

• Discs are identified by their total length and number of tracks. If

another disc happens to have the same specifications as one

that you have already stored a name for, the name will be

displayed for it, too.

The 4 button moves the cursor to the left, and the ¢

button to the right.

Each time the 38 button is pressed, the characters to be

entered change as listed below.

Press the DISC+ or DISC– button to display the desired

character.

• If you want to change the name of a disc, repeat steps 1 and 2

to display the name, and then repeat steps 3 and 4 to input the

changes.

Characters that can be displayed are as follows.

• Pressing the reset button erases the disc names stored in this

unit, but does not erase names stored in a disc changer.

• Each source (CD,DISC-CH1,DISC-CH2) has its own memory in

which to store the disc names.

Discs that have been disc name preset with the CD player will

not have their disc name displayed when played on a CD

changer.

Alphabet (upper case)/Numerals/Symbols:

A ~ Z 0~9 / + – *= < > []

Alphabet (lower case)/Numerals/Symbols:

a ~ z 0~9 / + – *= < > []

NOTE

The operation and characters that can be entered may change

as listed below, depending on the unit that is connected.

A press of the 38 button exits the disc name preset mode.

Operations can be followed again from Step 2 at a time such

— 21 —

Download from Www.Somanuals.com. All Manuals Search And Download.

DSP/ Equalizer/ Analyzer control features

DS P (Dig it a l S ig n a l P ro c e s s o r)

A DSP is a device which uses digital control to correct the

audio signal and produce sound effects that can com pensate

for the sm all passenger com partm ent of a vehicle.

The DSP indicator lights up when the DSP m ode is on.

This function reproduces m any different virtual sound fields

such as of a concert hall within a vehicle.

English

CD EJECT

OPEN

Sw itching the Sound Field Control:

NAME SET

DISP

Press the DSP button.

"DSP mode" is displayed once the DSP mode is entered.

ATT

Each time you press the DSP button, the sound field control

switches as follows;

▼

FM+

S.A

Outputs the sound source as-is without added

DISC

PWR OFF

B.S

METAL

AUD

FNC

"Bypass"

effects.

SRC

AM–

DSP

BNR

SCN

RDM

REP

D.SCN

M.RDM

DSP

▼

Recreates the gree and full sound of a large

"Stadium"

stadium.

▼

Reproduces a larger space inside the vehicle to

Sound field control name/

Preset Equalizer name/

Spectrum analyzer name

"Concert"

▼

recreate the live feel of a concert arena.

EQ indicator

DSP indicator

Fully reproduces the lively beat sound of a small

"Club Disco"

disco club.

▼

Reproduces the reverberation effects of a

traditional European cathedral.

"Church"

▼

Faithfully reproduces the source under optimum

"Listening"

acoustic conditions as in a living room.

Press the DSP button for at least one second to end the DSP

mode.

NOTE

Spectrum analyzer display

If you make no button operation for 10 seconds, the DSP mode

is automatically canceled.

— 22 —

Download from Www.Somanuals.com. All Manuals Search And Download.

If you make no button operation for 10 seconds, the equalizer

mode is automatically canceled.

P re s e t Eq u a lize r S e le c t io n

You can choose the equalizer from four settings whose sound

qualities are preset to m atch m usic or vehicle characteristics.

Sw itching the Preset Equalizer:

Press the EQ button.

"EQ mode" is displayed once the equalizer mode is entered.

S p e c t ru m An a lyze r Dis p la y S e le c t io n

You can select the display to enjoy sounds with eyes.

Each time you press the EQ button, the preset equalizer

switches as follows;

Sw itching the Spectrum Analyzer Display:

Press the S.A button.

"SPEANA mode" is displayed once the analyzer mode is

entered.

3"Rock" 3"Pops" 3"Vocal" 3"Heavy" 3"Flat

Press the EQ button for at least one second to end the

equalizer mode.

Each time you press the S.A button, the analyzer display

switches as follows;

NOTE

▼

The spectrum analyzer display switches in

sequence for 10 secconds each.

"SPEANA scan"

If you make no button operation for 10 seconds, the equalizer

mode is automatically canceled.

▼

"Peak Hold"

▼

"Squall"

▼

"Catcher"

▼

Eq u a lize r Le ve l Ad ju s t in g

You can adjust the level of the equalizer effects.

"Level Meter"

▼

"Rolling Bar"

▼

Press the EQ button.

"EQ mode" is displayed once the equalizer mode is entered.

"Stream"

▼

"Radar"

Each time you press the AM or FM button, the equalizer

effects switch as follows;

▼

"Falling Star"

▼

"LOW"

"MID"

"HIGH"

"Music Scope"

NOTE

• This adjustment cannot be made when the Preset Equalizer

Selection is set to "Flat".

• The default setting is "MID".

Press the S.A button for at least one second to end the

analyzer mode.

Press the EQ button for at least one second to end the

equalizer mode.

NOTE

If you make no button operation for 10 seconds, the analyzer

mode is automatically canceled.

NOTE

— 23 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Function Set System

Fu n c t io n S e t S ys t e m

To accom m odate a greater num ber of functions, a function set

system has been em ployed for m aking settings. Press the FNC

button to enter the function set m ode and then display the

function to m ake the setting.

English

Select the mode that you want to make the setting of the

function.

CD EJECT

OPEN

NAME SET

DISP

Press the FNC button for at least one second.

"Function Set" is displayed when the function set mode is

entered.

The function that you can adjust is indicated with the current

settings displayed.

ATT

Selecting function to set

FM+

S.A

Press the ¢ button to search through the functions until you

see the one you want to adjust in the display.

Press the 4 button to search through the functions

backward.

DISC

PWR OFF

B.S

METAL

AUD

FNC

SRC

AM–

DSP

BNR

SCN

RDM

REP

D.SCN

M.RDM

FNC

Example: If you want to switch the setting of the touch sensor

tone function from on to off, first search through the

functions until you see "BEEP On" in the display.

FNC indicator

Function mode and setting display

Changing setting for currently displayed function

Press either the AM or FM button.

The setting will change for each function.

Example: The setting of the touch sensor tone will switch from

on to off, and "BEEP Off" is displayed.

Ending the function set m ode

Press the FNC button for at least one second.

AUTO indicator

NOTE

• Make sure to end the function set mode when finished.

• To use the auto memory function, press either the AM or FM

button for at least two seconds.

— 24 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Fu n c t io n it e m s in S t a n d b y m o d e :

S e le c t in g Dis p la y Mo d e

The Display Mode sets the num ber of display colours used by

the Spectrum Analyser.

S w it c h in g p re o u t

Switch the preout between the rear and non-fading. The

factory default is rear preout.

Display and setting:

"Preout Rear" : Rear preout

"Preout N-F" : Non-fading preout

Display and setting:

"DISP MODE A" : The display can be set to use three colours:

white, light blue and blue.

"DISP MODE B" : The display can be set to use two colours:

white and blue.

Fu n c t io n it e m s in Tu n e r m o d e :

S e le c t in g Tu n in g Mo d e

You can choose from three tuning m odes: auto seek, preset

station seek, and m anual. The "AUTO 1" indicator lights up

when auto seek tuning is selected, and the "AUTO 2" indicator

lights when preset station seek tuning is selected.

Dim m e r Le ve l Ad ju s t m e n t

You can adjust the Dim m er level of the unit when your car's

light switch has been turned on.

Display and setting:

"DIM STEP 1" – "DIM STEP 5"

"Auto1 Seek" : Auto seek tuning mode

"Auto2 Seek" : Preset station seek tuning mode

"Manual Seek" : Manual tuning mode

NOTE

This function is available when the dimmer wire is connected and

the light switch of your car is turned on.

To u c h S e n s o r To n e

This function produces a beep sound that accom panies button

operation. It can be switched on or off.

Display and setting:

"BEEP On" : Beep setting is on.

"BEEP Off" : Beep setting is off.

NOTE

The beep sound is not output from the preout jacks.

— 25 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Function Set System

Basic Operations of rem ote

Au t o Me m o ry En t ry

You can autom atically store all the receivable frequencies in

the band currently being listened to, and then recall them with

the touch of a button later. This function is especially useful

when you are travelling and do not know what stations are

available. Up to six frequencies can be stored this way.

English

Display and setting:

–

Select the display "AME Ready" during the selecting function in

the menu system.

SRC

–

TUNE –/4/TRACK –

^TUNE+/¢/TRACK +

Press either the AM or FM button for at least two seconds to

start auto memory function.

FM/DISC +

TUNE

TRACK

ATT

The numbers of the preset station buttons showed in order.

When all the stations in a certain band are stored in the preset

memory, the auto memory entry stops. The tuner then plays

the last station received.

DSIC

–

^AM/DISC–

Canceling Auto Mem ory Entry During Its Operation:

Press the FNC button while auto memory entry is taking place

to stop the process.

DNPP/

SBF

Recalling a Preset Station:

Press the preset station button (#1-6) for the desired station.

The number of the recalled station is displayed.

Fu n c t io n it e m s in Ext e rn a l d is c c o n t ro l m o d e :

Te xt S c ro ll

This function perm its the CD text, MD title to be scrolled and

the entire text to be displayed. Switching between m anual

scrolling and autom atic scrolling is perm itted. The factory

default is autom atic scrolling.

REMOTE CONTROL UNIT

Display and setting:

"AT. SCRL On" : Automatic scrolling

"AT. SCRL Off" : Manual scrolling

— 26 —

Download from Www.Somanuals.com. All Manuals Search And Download.

2CAUTION

Ba s ic o p e ra t io n s

Do not set the remote on hot places such as above the

dashboard.

•

VOLUME buttons

Press the + button to turn the volume up.

Loading and Replacing the Batteries:

Use two "AAA"-size batteries.

Press the – button to turn the volume down.

SRC button

Slide the cover while pressing downwards to remove it as

illustrated.

Each time you press the SRC button, the mode switches as

follows:

Insert the batteries with the + and – poles aligned properly,

▼

following the illustration inside the case.

Tuner mode

▼

Tape mode

▼

CD mode

▼

External disc control mode 1

▼

External disc control mode 2/AUX mode

▼

Standby mode

2WARNING

Store unused batteries out of the reach of children. Contact a

doctor immediately if the battery is accidentally swallowed.

NOTE

• The mode switches to the next mode from any mode which

cannot be used.

• The external disc control mode will differ depending on the unit

that is connected.

• The AUX mode is available only when the changer / AUX

switching adapter (KCA-S210A or CA-C1AX) or CD changer

(KDC-CPS85, KDC-CX85, KDC-CPS82 or KDC-CX82) is

connected to this unit.

During the AUX mode, "AUX INPUT" will show in the display.

When the CA-C1AX is being used, the AUX Mode will replace

the External Disc Control Mode.

• The provided batteries are intended for use in operation

checking, and their service life may be short.

• When the remote controllable distance becomes short, replace

both of the batteries with new ones.

NOTE

A portion of the operations may not be possible, depending on

the unit that is connected.

•

ATT button

Turns down the volume quickly. To return the volume to its

original level, press the button again. Turning the volume up, or

turning it all the way down deactivates the attenuator function.

— 27 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic Operations of rem ote

Tu n e r fe a t u re s

CD/Ext e rn a l d is c c o n t ro l fe a t u re s

• 4/¢ (TUNE) buttons

• 4/¢ buttons

Press the 4 button to make decreasing seeks (using the

preset tuning mode).

Press the 4 button to search through the tracks backward.

Press the ¢ button to search through the tracks forward.

Use to move the cursor while entering disc name.

English

Press the ¢ button to make increasing seeks (using the preset

tuning mode).

•

DISC buttons (for disc changers)

Use to move the cursor left or right during station name input.

Press the DISC– button to search through the discs backward.

Press the DISC+ button to search through the discs forward.

Select numbers and symbols while entering disc name.

•

AM/FM button

Press the AM button to select the AM band.

Press the FM button to select and switch between FM1, FM2,

and FM3 bands.

• 38 button

When a disc is playing, this button pauses the play.

Press the same button again to start play again.

Selects the type of characters at the time of entering the disc

name.

During station name input, selects digits and symbols.

• 38 button

Selects the type of characters at the time of entering the station

name.

•

OK button

•

OK button

During disc name input, stores the already input data in memory

and ends the input mode.

During station name input, stores the already input data in

memory and ends the input mode.

Ca s s e t t e p la ye r fe a t u re s

• 4/¢ buttons

Press the 4 button to start play again at the beginning of the

current track.

Press the ¢ button to start play at the beginning of the next

track.

•

AM button

Rewinds the tape.

FM button

Fast forwards the tape.

• 38 button

Plays the reverse side of the tape. When pressed during fast

forward and rewind, this button stops the tape and starts playing

it.

— 28 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Ac c e s s o rie s

In s t a lla t io n P ro c e d u re

1. To prevent a short circuit, remove the key from the ignition and

External view

......... Num ber of item s

disconnect the - battery.

......... Num ber of item s

2. Make the proper input and output wire connections for each unit.

3. Connect the speaker wires of the wiring harness.

(M5×6mm)

.........6

4. Connect the wiring harness wires in the following order: ground,

battery, ignition.

.........1

(M3×6mm)

5. Connect the wiring harness connector to the unit.

6. Install the unit in your car.

(M4×6mm)

.........1

.........2

7. Reconnect the - battery.

8. Press the reset button.

(M5×6mm)

.........1

.........6

2CAUTION

• If your car's ignition does not have an ACC position, connect

the ignition wires to a power source that can be turned on and

off with the ignition key. If you connect the ignition wire to a

power source with a constant voltage supply, as with battery

wires, the battery may die.

• If the console has a lid, make sure to install the unit so that the

faceplate will not hit the lid when closing and opening.

• If the fuse blows, first make sure the wires aren’t touching to

cause a short circuit, then replace the old fuse with one with

the same rating.

• Do not let unconnected wires or terminals touch metal on the

car or anything else conducting electricity. To prevent a short

circuit, do not remove the caps on the ends of the

unconnected wires or the terminals.

• Insulate unconnected wires with vinyl tape or other similar

material.

(M5×10mm)

.........2

.........1

• Connect the speaker wires correctly to the terminals to which

they correspond. The unit may be damaged or fail to work if

you share the - wires or ground them to any metal part in the

car.

• After the unit is installed, check whether the brake lamps,

blinkers, wipers, etc. on the car are working properly.

• Some disc changers need conversion cords for connection. See

the section on "Safety Precautions" for details.

2CAUTION

The use of any accessories except for those provided might result

in damage to the unit. Make sure only to use the accessories

shipped with the unit, as shown above.

• Mount the unit so that the mounting angle is 30° or less.

— 29 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Co n n e c t in g Wire s t o Te rm in a ls

Front left output (White)

Front right output (Red)

Rear left output (White)/

Non-fading left output (White)

Fuse

(10A)

English

Rear right output (Red)/

Non-fading right output (Red)

M4×8mmMAX

FUSE 10A

FM/AM antenna input

KENWOOD disc changer control input

NOTE

To connect the Disc changer,

consult your Disc changer manual.

Automatic illumination/Dimmer

control wire (Orange)

ILLUMI

Wiring harness

(Accessory#)

To car light control switch

Power control wire

(Blue/White)

When using the optional power

amplifier, connect to its power

control terminal.

White/Black

–

To front left

speaker

P.CONT

FRONT•L

White⁺

Depending on what antenna you are using,

connect either to the control terminal of the

motor antenna, or to the power terminal for

the booster amplifier of the film-type antenna.

Motor antenna control wire

(Blue)

Gray/Black

–

To front right

speaker

ANT

FRONT•R

Gray ⁺

CONT

Ignition key

switch

Green/Black

–

ACC

Ignition wire (Red)

To rear left

speaker

REAR•L

Green⁺

ACC

Car fuse

box

Purple/Black

Battery wire (Yellow)

–

To rear right

speaker

BATT

(Main

REAR•R

Car fuse box

fuse)

Purple

Ground wire (Black) - (To car chassis)

Battery

2CAUTION

–

When only two speakers are being connected to the

system, connect the connectors either to both the front

output terminals or to both the rear output terminals (do not

mix front and rear). For example, if you connect the +

connector of the left speaker to a front output terminal, do

not connect the - connector to a rear output terminal.

2WARNING

If you connect the ignition wire (red) and the battery wire

(yellow) to the car chassis (ground), you may cause a short

circuit, that in turn may start a fire. Always connect those

wires to the power source running through the fuse box.

— 30 —

Download from Www.Somanuals.com. All Manuals Search And Download.

In s t a lla t io n (fo r TOYOTA, NIS S AN Ca r e t c .)

In s t a lla t io n (fo r HONDA ACURA Ca r)

You can choose from three installation types to fit your car.

Perform "Assem bly" before installation.

2CAUTION

When performing a check of the CD operation prior to installation,

place this unit in a hirizontal position and perform a loading/eject

of the CD.

■

Assem bly

■

Installation

Install onto the car bracket using the supplied screws (M5 × 6

mm). The holes of the car bracket to use will differ depending on

the car model.

Fit the projections on both sides of the

Accessories 6 and 7 into the slits on

the Accessory4.

Accessory4

Accessory0

(M5 × 6 mm)

Accessory2

(M4 × 6 mm)

Bottom

panel

When a ground wire is

included in the wiring kit

(which is sold separately),

fasten the ground wire

with the binding screw

located on the rear panel

of this unit.

Accessory1

or Accessory0

(M5 × 6 mm)

(The application

position of

Accessory5 is at the

bottom panel)

Accessory6 (L)

Accessory0

(M5 × 6 mm)

Accessory7 (R)

Accessory3

(Only for NISSAN car)

— 31 —

Download from Www.Somanuals.com. All Manuals Search And Download.

In s t a lla t io n (fo r HONDA ACURA Ca r)

■

Installation type 1

Installation type 2

Use Accessory1 to attach the

unit which was assembled in

Assembly.

Install the center panel

with the unit in your car.

Remove the factory-installed

car stereo and install the unit.

Attach Accessory8 which

was assembled in

Assembly.

NOTE

English

Factory-installed

car stereo

Accessory1

(M5 × 6 mm)

The illustration shows an

example of installation

using a vehicle bracket.

The shape of the bracket

varies with the vehicle to

be installed. Some bracket

requires three screws

(Accessory1) on each

side.

Accessory8 is to be fixed either

to the center or bottom,

depending on the car model.

Accessory0

(M5 × 6 mm)

DPX-4010

Accessory8

Accessory!

(M5 × 10 mm)

Accessory9

(M3 × 6 mm)

NOTE

If accessories 6 and 7 hit the inside of the console, preventing

the unit from being attached tightly, snap their end parts off as

shown below.shipped with the unit, as shown above.

■

Installation type 3

Remove the factory-installed

car stereo and install the unit.

Attach Accessory@ to

Accessory8 which was

assembled in Assembly.

Factory-installed

car stereo

Accessory67

Accessory0

(M5 × 6 mm)

Accessory8

DPX-4010

2CAUTION

Be careful not to get injured with the new edge.

Accessory9

(M3 × 6 mm)

Accessory!

(M5 × 10 mm)

Reuse the screws

that were removed.

Accessory@

— 32 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Tro u b le s h o o t in g Gu id e

What m ight seem to be a m alfunction in your unit m ay just be the result of slight m isoperation or m isw iring. Before

calling service, first check the follow ing table for possible problem s.

PROBLEM

POSSIBLE CAUSE

SOLUTION

The power does not turn on.

The fuse has blown.

After checking for short circuits in the wires, replace the

fuse with one with the same rating.

No sound can be heard, or the

volume is low.

Attenuator is turned on.

Turn off Attenuator.

The fader or balance settings are set all the way to one

side.

Reset the fader or balance settings.

The input/output wires or wiring harness are connected

incorrectly.

Reconnect the input/output wires or the wiring harness

correctly. See the section on "Connecting Wires to

Terminals".

The cassette tape is bad.

Try playing another cassette tape. If works fine, the first

tape was bad.

The tape does not go in. /

No sound can be heard even

though the tape display is

made.

The car ignition was turned off during tape eject; or the

tape was pulled out during loading, switching the mode

to tape mode even though no tape is in.

Press the Eject button.

Nothing happens when the

buttons are pressed.

The computer chip in the unit is not functioning normally.

The tape head is dirty.

Press the reset button on the unit (see p. 5).

Clean the tape head, referring to the section on "Cleaning

the tape head" (see p. 5).

The sound quality is poor or

distorted.

One of the speaker wires is being pinched by a screw in

the car.

Check the speaker wiring.

The speakers are not wired correctly.

Reconnect the speaker wires so that each output terminal is

connected to a different speaker.

Radio reception is poor.

The car antenna is not extended.

Pull the antenna out all the way.

The antenna control wire is not connected.

Connect the wire correctly, referring to the section on

"Connecting Wires to Terminals".

— 33 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Tro u b le s h o o t in g Gu id e

PROBLEM

POSSIBLE CAUSE

SOLUTION

The memory is erased when

the ignition is turned off.

The battery wire has not been connected to the proper

terminal.

Connect the wire correctly, referring to the section on

"Connecting Wires to Terminals".

The ignition and battery wire are incorrectly connected.

Connect the wire correctly, referring to the section on

"Connecting Wires to Terminals".

English

A CD ejects as soon as it is

loaded.

The CD is upside-down.

The CD is quite dirty.

Load the CD with the labeled side up.

Clean the CD, referring to the section on "Cleaning CDs"

(see p. 6).

The sound skips on a CD.

A track will not play.

The CD is scratched or dirty.

Clean the CD, referring to the section on "Cleaning CDs"

(see p. 6).

Random play has been selected.

Turn off random play.

The DSP effects are

imperceptible.

You are using a two-speaker system.

Use a front/rear four-speaker system.

The front and rear output are reversed.

Connect the wire correctly, referring to the section on

"Connecting Wires to Terminals".

Connect the wire correctly, referring to the section on

"Connecting Wires to Terminals".

The + and - of speakers are reversed.

The fader or balance settings are set all the way to one

side.

Reset the fader or balance settings.

— 34 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Disc Control Mode

PROBLEM

POSSIBLE CAUSE

SOLUTION

The disc control mode cannot

be selected.

No cable has been connected to the disc changer input

terminal on the unit.

Connect the cable to the disc changer input terminal on the

unit.

The specified disc does not

play, but another one plays

instead.

The specified CD is quite dirty.

Clean the CD.

The CD is upside-down.

Load the CD with the labeled side up.

The disc is loaded in a different slot from that specified.

Eject the disc magazine and check the number for the

specified disc.

The disc is severely scratched.

Something is touching the disc changer.

The CD is scratched or dirty.

Try another disc instead.

The sound skips.

Remove whatever is touching it.

If skipping happens at the same place when the car is

stopped, something with the CD is wrong. Clean the CD.

The computer chip in the unit is not functioning normally.

Press the reset button on the unit (see p. 5).

The display shows that the

changer is being played, but no

sound can be heard.

The specified track will not

play.

Random play or magazine random play has been

selected.

Turn off random play or magazine random play.

Track repeat, disc repeat, track

scan, disc scan, random play,

and magazine random play

start by themselves.

The setting is not cancelled.

The settings for these functions remain on until the

setting to off or the disc ejected, even if the power is

turned off or the source changed.

CD-R or CD-RW will not play.

Disc has not undergone finalisation processing

Disc will not play on CD Changer.

A CD-R or CD-RW cannot be played until it has

undergone finalisation processing on the CD Recorder.

If your CD Changer does not support CD-Rs or CD-RWs,

you will not be able to play these discs.

If the follow ing situations, consult your nearest service center:

• Even though the disc changer is connected, the Disc Changer Mode is not on, with "AUX INPUT" showing in the display during the Changer Mode.

• Even though no device (KCA-S210A, CA-C1AX, KDC-CPS85, KDC-CX85, KDC-CPS82 or KDC-CX82) is connected, the AUX Mode is entered when switching modes.

— 35 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Tro u b le s h o o t in g Gu id e

The follow ing m essages are displayed w hen certain problem s are occurring in your system . Take the recom m ended

actions.

No disc magazine has been loaded in the changer. The disc magazine is not completely loaded.

EJECT

No Disc

Error 04

]

Load the disc magazine properly.

No disc has been loaded in the disc magazine.

English

]

Load a disc into the disc magazine.

No disc has been loaded in the disc magazine.

]

Load a disc into the disc magazine.

The CD is quite dirty. The CD is upside-down. The CD is scratched a lot.

]

Clean the CD and load it correctly.

Nothing has been recorded on the MD.

Blank

]

The next MD will automatically be played.

No tracks are recorded on the MD, although it has a title.

No Track

Error 77

Error 99

]

The next MD will automatically be played.

The unit is malfunctioning for some reason.

]

Press the reset button on the unit. If the "Error 77" code does not disappear, consult your nearest service center.

Something is wrong with the disc magazine. Or the unit is malfunctioning for some reason.

]

Check the disc magazine. And then, press the reset button on the unit.

If the "Error 99" code does not disappear, consult your nearest service center.

The protective circuit in the unit activates when the temperature inside the automatic disc changer exceeds 60°C (140°F),

stopping all operation.

Hold

]

Cool down the unit by opening the windows or turning on the air conditioner. As the temperature falls below 60°C (140°F), the

disc will start playing again.

An attempt was made to display the track/disc title of the CD during play, but the CD has no texts.

No Text

No Title

No Name

An attempt was made to display the track/disc title of the MD disc during play, but the MD has no titles.

• An attempt was made to display the name of the station being received but it was not set in memory.

• An attempt was made to display the name of the disc being played but it was not set in memory.

• An attempt was made to display the station name/disc name after the battery had been removed for a long period.

The tape player is malfunctioning.

]

Eject the tape and try inserting it again.

Contact the Kenwood dealer if this indicator continues blinking or the tape cannot be ejected.

The CD player is malfunctioning.

]

Eject the CD and try inserting it again.

Contact the Kenwood dealer if this indicator continues blinking or the CD cannot be ejected.

— 36 —

Download from Www.Somanuals.com. All Manuals Search And Download.

S p e c ific a t io n s

Specifications subject to change w ithout notice.

FM tuner section

CD player section

Frequency range (200 kHz space) ............87.9 MHz – 107.9 MHz

Usable sensitivity (S/N = 30dB) ....................9.3dBf (0.8 µV/75 Ω)

Quieting Sensitivity (S/N = 50dB) ..............15.2dBf (1.6 µV/75 Ω)

Frequency response (±3.0 dB)..............................30 Hz – 15 kHz

Signal to Noise ratio (MONO)..............................................70 dB

Selectivity (±400 kHz) ......................................................≥ 80 dB

Stereo separation (1 kHz) ....................................................40 dB

Laser diode ....................................................GaAlAs (λ=780 nm)

Digital filter (D/A) ....................................8 Times Over Sampling

D/A Converter ......................................................................1 Bit

Spindle speed ..............................................500 – 200 rpm (CLV)

Wow & Flutter........................................Below Measurable Limit

Frequency response (±1 dB) ................................10 Hz – 20 kHz

Total harmonic distortion (1 kHz) ......................................0.01 %

Signal to Noise ratio ................................................93 dB (1 kHz)

Dynamic range ....................................................................93 dB

Channel separation ..............................................................85 dB

AM tuner section

Frequency range (10 kHz space) ..................530 kHz – 1700 kHz

Usable sensitivity (S/N = 20dB) ............................28 dBµ (25 µV)

Audio section

Cassette player section

Maximum output power..................................................45 W × 4

Full bandwidth power (at less than 1% THD) ................22 W × 4

Preout level / Load ................................................1500mV/10kΩ

Preout impedance ............................................................≤ 600 Ω

Tape speed ..............................................................4.76 cm/sec.

Wow & Flutter (WRMS) ....................................................0.08 %

Frequency response (70 µs) ....................25 Hz – 22 kHz (±3 dB)

Separation (1 kHz) ..............................................................40 dB

Signal to Noise ratio

General

(Dolby NR OFF)..........................................................60 dB

(Dolby B NR ON)........................................................68 dB

Operating voltage ............................14.4 V (11 – 16 V allowable)

Current consumption ................................10.0 A at Rated power

Installation size (W × H × D) ........................178 × 100 × 155 mm

7 × 3-15/16 × 6-1/8 in.

Weight ................................................................5.9 Lbs (2.7 kg)

— 37 —

Download from Www.Somanuals.com. All Manuals Search And Download.

Ingersoll Rand Heat Pump 670079 User Manual
Insignia Portable Stereo System NS B3113 User Manual
John Lewis Fan 85573601 User Manual
JVC MP3 Docking Station 0397MKVUNYP User Manual
Kalorik Refrigerator CKS 40211 User Manual
Keys Fitness Treadmill ALL800 User Manual
King Canada Saw KC 1401HD User Manual
KitchenAid Refrigerator NL240V User Manual
Korg DJ Equipment EFGS 1 User Manual
Kowa Microscope Magnifier TSN 773 User Manual