OWNER'S MANUAL
DC-650TS Dust Collector
JET EQUIPMENT & TOOLS, INC.
A WMH Company
P.O. BOX 1349
Auburn, WA 98071-1349
e-mail [email protected]
Phone:253-351-6000
Fax: 1-800-274-6840
M-708630 08/01
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
1.
2.
Read and understand the entire contents of this manual before attempting assembly or
operation. Do not use this machine until proper training and knowledge has been obtained.
Do not leave Dust Collector when plugged in. Unplug from outlet when not in use and before
servicing.
3.
4.
5.
6.
Do not use outdoors or on wet surfaces.
Do not allow to be used as a toy. Close attention is necessary when used near children.
Use only as described in this manual. Use only manufacturer’s recommended attachments.
Do not use with damaged cord or plug. If Dust Collector is not working as it should, has been
dropped, damaged, left outdoor, or dropped in water, return it to a service center.
7.
Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp
edges or corners. Do not run Dust Collector over cord. Keep cord away from heated surfaces.
8.
9.
Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
Do not handle plug or Dust Collector with wet hands.
10. Do not put any objects into the openings. Do not use with any opening blocked; keep free of dust,
lint, hair, and anything that may reduce air flow.
11. Keep hair, loose clothing, fingers, and all parts of body away from opening and moving parts.
12. Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
13. Do not use without dust bag and/or filters in place.
14. Turn off all controls before unplugging.
15. Use extra care when cleaning on stairs.
16. Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they
may be present.
17. Do not operate without hose connected to the hose inlet. Hazardous moving parts inside. Unplug
before removing hose inlet or impeller guard.
18. Some dust created by power sanding, sawing, grinding, drilling and other construction activities
contains chemicals known to cause cancer, birth defects or other reproductive harm. Some
examples of these chemicals are:
•
•
•
Lead from lead based paint
Crystalline silica from bricks and cement and other masonry products, and
Arsenic and chromium from chemically-treated lumber.
19. Your risk from those exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals: work in a well ventilated area, and work with approved
safety equipment, such as those dust masks that are specifically designed to filter out microscopic
particles
20. Do not operate tool while under the influence of drugs, alcohol or any medication.
21. Make sure the extension cord is in good condition. When using an extension cord, be sure to use
one heavy enough to carry the current your product will draw. An undersize cord will cause a drop
in the line voltage resulting in loss of power and overheating. The table below shows the correct
size to use depending on cord length and nameplate ampere rating. If in doubt, use the next
heavier gauge. The smaller gauge number, the heavier the cord.
22. Static electricity will build up in the filter during operation. The filter ground must be attached to the
machine ground, and to the filter.
Cord Length
Cord Gauge
16 AWG
25’
50’
16 AWG
100’
150’
14 AWG
12 AWG
SAVE THESE INSTRUCTIONS
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Grounding Instructions
Caution: This tool must be grounded while in use to protect the operator from electric shock.
In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric
current to reduce the risk of electric shock. This tool is equipped with an electric cord having an
equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet
that is properly installed and grounded in accordance with all local codes and ordinances.
Do not modify the plug provided. If it will not fit the outlet, have the proper outlet installed by a qualified
electrician.
Improper connection of the equipment-grounding conductor can result in a risk of electric shock. The
conductor, with insulation having an outer surface that is green with or without yellow stripes, is the
equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not
connect the equipment-grounding conductor to a live terminal.
Check with a qualified electrician or service personnel if the grounding instructions are not completely
understood, or if in doubt as to whether the tool is properly grounded. Use only three wire extension
cords that have three-prong grounding plugs and three-pole receptacles that accept the tool’s plug.
Repair or replace a damaged or worn cord immediately.
115 Volt Operation
As received from the factory, your dust collector is ready to run at 115 volt operation. This dust
collector, when wired for 115 volt, is intended for use on a circuit that has an outlet and a plug that looks
like the one illustrated in (A). A temporary adapter, which looks like the adapter as illustrated in (B), may
be used to connect this plug to a two-pole receptacle, as shown in (B) if a properly grounded outlet is not
available. The temporary adapter should only be used until a properly grounded outlet can be installed
by a qualified electrician. This adapter is not applicable in Canada. The green colored rigid ear, lug,
or tab, extending from the adapter, must be connected to a permanent ground such as a properly
grounded outlet box, as shown in (B).
4
Download from Www.Somanuals.com. All Manuals Search And Download.
230 Volt Operation
If 230V, single phase operation is desired, the following instructions must be followed:
1. Disconnect the machine from the power source.
2. This dust collector is supplied with four motor leads that are connected for 115V operation, as shown
in Figure A. Reconnect these four motor leads for 230V operation, as shown in Figure B.
3. The 115V attachment plug (A), supplied with the dust collector, must be replaced with a UL/CSA
listed plug suitable for 230V operation (D). Contact your local Authorized JET Service Center or
qualified electrician for proper procedures to install the plug. The dust collector must comply with all
local and national codes after the 230 volt plug is installed.
4. The dust collector with a 230 volt plug should only be connected to an outlet having the same
configuration (D). No adapter is available or should be used with the 230 volt plug.
Important: In all cases (115 or 230 volts), make certain the receptacle in question is properly grounded.
If you are not sure, have a registered electrician check the receptacle.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications:
DC-650TS
Stock Number................................................................................................................................ 708630
Blower Wheel Diameter........................................................................................................................11”
Sound Rating at 3 feet................................................................................................................. 60-70 db
Hose Diameter........................................................................................................................................4”
Air Flow (CFM) .................................................................................................................................... 650
Velocity at 4” (FPM).......................................................................................................................... 7,445
Static Pressure (inch of water)............................................................................................................ 7.80
Overall Dimensions ...................................................................................................26-3/16" dia. x 28" H
Motor (TEFC) ..........................................................................................................1 HP, 1Ph 115V/230V
Net Weight (approx.) .......................................................................................................................53 lbs.
Table of Contents
Page
Warranty .................................................................................................................................................2
Warnings.................................................................................................................................................3
Grounding Instructions.............................................................................................................................4
115 Volt Operation...................................................................................................................................4
230 Volt Operation...................................................................................................................................5
Specifications..........................................................................................................................................6
Table of Contents ....................................................................................................................................6
Unpacking DC-650TS..............................................................................................................................7
Contents of Shipping Carton....................................................................................................................7
Tools Required for Assembly...................................................................................................................7
Assembly.................................................................................................................................................8
Electrical Connections .............................................................................................................................9
Turning the Machine On & Off .................................................................................................................9
Maintenance.......................................................................................................................................9-10
Parts Breakdown and Parts List ........................................................................................................11-12
Wiring Diagram .....................................................................................................................................13
The specifications in this manual are given as general information and are not binding. JET Equipment
& Tools reserves the right to effect, at any time and without prior notice, changes or alterations to parts,
fittings, and accessory equipment deemed necessary for any reason whatsoever.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
material, fittings, construction and grounding.
Stock # JW1050V
WARNING
Read and understand the entire contents of
this manual before attempting assembly or
operation of the dust collector!
Failure to comply may cause serious injury!
Unpacking
1. Finish removing all contents from the
shipping carton.
2. Report any damage to your distributor.
3. Do not discard any shipping material until
after the dust collector has been assembled
and is running properly.
Contents of the Shipping Carton
1. Plastic Cover/Motor/Fan Assembly
1. Hose
1. Owner's Manual
1. Warranty Card
1. Filter
1. Hose Clamp
1. Plastic impeller guard
1. Metal Deflector
1. Elbow
1. Harware Package
Tools Required for Assembly
2. 10mm Wrenches or sockets
1. #2 Cross Point Screw Driver
The JET DC-650TS does not come with a
collector can. You can use the JET two stage
dust collector on a variety of round, metal and
plastic collector cans. The outer diameter of the
trash can should be approximately 20-1/4” – 24-
1/4” to fit properly.
Use the proper type hose (C, Fig. 5) to connect
the dust collector to the machine being
operated. Dryer vent hose is not acceptable for
this purpose.
distributor for the full line of JET Dust Collector
Hoses and Accessories. Customize your
Contact your nearest JET
installation and obtain maximum performance
with JET's dust hoods, hoses, clamps, fittings,
and blast gates.
Order the Dust Collection Basics Video which
covers topics such as system design, duct
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
WARNING
The dust collector must be disconnected
from the power source during assembly.
Failure to comply may result in serious
injury!
The JET DC-650TS does not come with a
collector can. You can use the JET two stage
dust collector on a variety of round, metal and
plastic collector cans. The outer diameter of the
trash can should be approximately 20-1/4” – 24-
1/4” to fit properly.
1. Attach the deflector (A, Fig. 1) to the plastic
cover using two hex cap screws, four flat
washers and two hex nuts (B, Fig. 1).
Tighten the hardware.
2. Attach the impeller guard (C, Fig. 1) to the
plastic cover with three flat washers and
three hex nuts (D, Fig. 1). Tighten the
hardware
WARNING
To reduce the risk of injury from moving
parts, always keep impeller guard in place.
Failure to comply may result in serious
injury!
3. Slide the elbow (A, Fig. 2) over the impeller
housing exhaust, and tighten in place with
one hex cap screw, one flat washer and one
hex nut (B, Fig. 2).
4. Connect the filter (A, Fig. 3) to the elbow
and turn counter-clockwise so that it locks in
place.
WARNING
Static electricity will build up in the filter
during operation. The filter ground must be
attached to the machine ground, and to the
filter. Failure to comply may result in
fire/loss of property, or personal injury!
5. Attach the grounding clip (A, Fig. 6) to the
metal part of the filter. This will prevent
static electricity from building up in the filter.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connections
WARNING
All electrical connections must be done by
a qualified electrician. All adjustments or
repairs must be done with the dust
collector disconnected from the power
source, unplugged. Failure to comply may
result in serious injury!
The DC-650TS dust collector is rated
115V/230V, Prewired 115V.
If you want to run the DC-650TS on 230V refer to
the wiring diagram found on the inside of the
switch box cover (A, Fig. 4).
Before hooking up to the power source, make
sure that the switch is in the off position.
Turning the Machine On & Off
Note: Before hooking up to the power source,
make sure that the switch is in the off position.
1. The dust collector can be turned on by
flipping the switch (B, Fig. 4) into the on
position.
2. There is a removable key in the tip of the
switch that can be removed in the off
position. When the key has been removed
the dust collector cannot be used.
Maintenance
WARNING
Never perform maintenance on this machine
before turning switch off and removing plug
from power source, unplug.
Failure to comply may cause serious injury!
Motor
Make frequent inspections of the motor cover (C,
Fig. 4) and blow out (with low pressure air hose)
or vacuum any accumulation of foreign material
in order to maintain normal motor ventilation.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning the Filter
Order the Dust Collection Basics Video which
covers topics such as system design, duct
material, fittings, construction and grounding.
Stock # JW1050V
CAUTION
Wearing a particle mask/respirator for
protection against fine dust particles during
cleaning is highly recommended.
Clean both the filter and collector can frequently
to keep the collector's performance at its
optimum. To clean:
1. Disconnect the machine from the power
source.
2. Take off the grounding clip and remove the
filter (A, Fig. 5) by turning clockwise.
3. Empty the contents into an appropriate
container.
4. The filter can be cleaned with a low
pressure air hose. Blow from the outside of
the filter to clean the dust particles. For
best results check and empty the filter
frequently. Some applications will fill up the
filter quicker than others.
WARNING
Static electricity will build up in the filter
during operation. The filter ground must be
attached to the machine ground, and to the
filter. Failure to comply may result in
fire/loss of property, or personal injury!
5. Install the filter and reattach the grounding
clip.
Emptying the Collector Can
1. Disconnect the machine from the power
source, unplug.
2. Lift the dust collector off the collector can
(B, Fig. 5).
3. Dispose of the contents in the collector can.
Use the proper type hose (C, Fig. 5) to connect
the dust collector to the machine being
operated. Dryer vent hose is not acceptable for
this purpose.
distributor for the full line of JET Dust Collector
Hoses and Accessories. Customize your
Contact your nearest JET
installation and obtain maximum performance
with JET's dust hoods, hoses, clamps, fittings,
and blast gates.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts Breakdown
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List for the DC-650TS
Index Part
No. No.
Description
Size
Qty.
1..........331019AW ................... Impeller Housing (upper) ....................... ...............................................1
2..........331019BW ................... Impeller Housing (lower)........................ ...............................................1
3..........MH331001 ................... Motor.....................................................115V/230V, 1HP, 1Ph .............1
............DC1100-50W ............... Motor Fan Cover (not shown) ................ ...............................................1
............MF411012.................... Motor Fan (not shown)........................... ...............................................1
............CA003030.................... Running Capacitor (not shown)..............30MFD, 300V..........................1
............CA020010.................... Starting Capacitor (not shown)...............200MFD, 125V........................1
............DC650TS-CS ............... Centrifugal Switch (not shown)............... ...............................................1
4..........994532......................... Switch.................................................... ...............................................1
5..........999910......................... Power Cord............................................ ...............................................1
6..........423023......................... Motor Packing ....................................... ...............................................1
7..........331020......................... Impeller .................................................11” ..........................................1
8..........998621......................... Strain Relief........................................... ...............................................1
9..........KS050525 .................... Key........................................................5x5x25....................................1
10........331001......................... Cover .................................................... ...............................................1
11........HS430018.................... Hose......................................................4”x6’........................................1
12........331004......................... 6” Plastic Impeller Guard ....................... ...............................................1
13........331016......................... Gasket................................................... ...............................................1
14........331023......................... Gasket................................................... ...............................................1
15........423968......................... Ring Clamp ...........................................4” ............................................1
16........331021......................... Deflector................................................ ...............................................1
17........331018......................... Elbow .................................................... ...............................................1
18........331022......................... Filter...................................................... ...............................................1
19........331027......................... Gasket................................................... ...............................................1
20........SG060500.................... Hex Head Bolt W/Flange.......................M6x25.....................................5
21........TS-1482021 ................. Hex Head Bolt * ....................................M6x12................................(2) 6
22........TS-1482041 ................. Hex Head Bolt * ....................................M6x20................................(1) 1
23........WF061310 ................... Flat Washer * .......................................M6x13................................(8) 8
24........WF164030 ................... Flat Washer...........................................M16x40...................................1
25........TS-1551041 ................. Spring Washer.......................................M6 ..........................................4
26........TS-1540041 ................. Nut * .....................................................M6 .....................................(6) 6
27........TS-0561072 ................. Nut ........................................................5/8”-18UNF .............................1
28........TS-1540041 ................. Nut ........................................................M6 ........................................14
29........SG069300.................... Hex Head Bolt W/Flange.......................M6x12.....................................9
30........WF061620 ................... Flat Washer...........................................M6x16.....................................4
31........331033......................... Grounding Clip ...................................... ...............................................1
............DC650TS-NP ............... Name Plate (not shown) ........................ ...............................................1
............DC650TS-WL .............. Warning Label (not shown) .................... ...............................................1
............DC650TS-HP ............... Hardware Package (not shown) ............. ...............................................1
* indicates included in Hardware Package
(#) indicates quantity included in Hardware Package
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Wiring Diagram
13
Download from Www.Somanuals.com. All Manuals Search And Download.
|