Technical Guide
AJ-V8 Engine
and
5HP24 Transmission
Introduction
Published by Service Communications, Jaguar Cars Limited
Publication Part No JJM 18 15 15/70, August 1996
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents AJ-V8/5HP24
Subject
Page
Glossary
Abbreviations
2
3
Introduction
Engine
Basic Engine
Engine Cooling
5
17
Engine Lubrication
Variable Valve Timing
Air Intake System
Fuel System
Ignition System
Crankcase Ventilation
EGR System
Engine Accessories
Accessory Drive
Engine Harness
Engine Covers
20
24
27
33
35
35
37
38
39
41
42
43
Engine Specifications
Engine Management
ECM
45
53
58
58
59
60
61
61
61
62
62
62
62
62
63
Electronic Throttle
Fuel Pump
Fuel Injection
Ignition
EVAP System
Variable Valve Timing
EGR System
Engine Starting
HO2S Heaters
Instrument Cluster
A/C Compressor Clutch
Windshield and Backlight Heaters
Radiator Cooling Fans
Diagnostics
Transmission
Introduction
Technical Data
Gearshifting
Mechanical Description
Electrical Description
65
66
66
66
67
Transmission Management
Transmission Management
68
Service Tools
New Tools
72
1
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24 Glossary
The following abbreviations are used in this document:
Abbreviation
Description
ABS
A/C
anti-lock braking system
air conditioning
A/CCM
BPM
BHP
˚C
air conditioning control module
body processor module
brake horse power
degree Celsius
CAN
CDI
DIN
dc
controller area network
cubic inch displacement
Deutsche Institut für Normung
direct current
DTC
ECM
ECT
EGR
EMS
EVAP
˚F
diagnostic trouble code
engine control module
engine coolant temperature
exhaust gas recirculation
engine management system
evaporative emission
degree Fahrenheit
foot
ft
HO2S
in
heated oxygen sensor
inch
JDS
lb
Jaguar diagnostic system
pound
lbf.ft
kg
pound force feet
kilogram
km/h
kW
kilometer per hour
kilowatt
m
meter
MAFS
MIL
mph
mm
ms
mass air flow sensor
malfunction indicator lamp
miles per hour
millimeter
millisecond
Nm
Newton meter
NOx
OBD
O2S
PAS
PDU
psi
PTFE
rpm
SAE
SCP
TCM
USA
V
nitrous oxide
on-board diagnostics
oxygen sensor
power assisted steering
portable diagnostic unit
pounds per square inch
polytetrafluoroethane
revolutions per minute
Society of Automotive Engineers (USA)
standard corporate protocol
transmission control module
United States of America
volt
VSV
vacuum solenoid valve
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction AJ-V8/5HP24
The AJ-V8 4.0 litre, engine is the first of a new family of Jaguar engines. Designed to give excellent
performance, refinement, economy and low vibration levels it also conforms to the strictest emission
legislation. Weighing only 200 kilograms (441 lb), the engine is shorter by 12 inches (300 mm) than the
current AJ16 4.0 litre engine. Compression ratio is 10.75:1, with four valves per cylinder. The cylinder
heads, block and bedplate are all cast aluminum. Cylinders have electro-plated bores which reduce
piston friction, improve warm-up and oil retention. A variable valve timing system has been introduced
to give improved low and high-speed engine performance and excellent idle quality. The valve gear is
chain driven for durability. Low valve overlap improves engine idle speed and low residual fuel levels
which improves combustion and reduces hydrocarbon emissions. The inlet manifold is a one-piece,
composite moulding with integral fuel rails connecting to the eight side feed fuel injectors. Air flow into
the engine is via an electronic throttle assembly. Movement of the throttle is controlled by sensors in
the throttle assembly through the ECM. The engine has a low volume, high velocity, cooling system
which achieves a very fast warm-up with reduced and even metal temperatures in the combustion
chamber and increased bore temperatures.
The generator, A/C pump, and PAS pump are mounted to the cylinder block on rigid cradle supports.
Accessory drive is from a single, 7-ribbed vee belt. Hydraulic engine mounts minimise noise and
vibration.
A new engine management system adjusts fuel and ignition settings, monitors and controls exhaust
emissions and provides an on-board diagnostic capability.
The transmission is a new ZF 5-speed, automatic, electronically controlled unit.
The unit is oil filled for life so does not have an oil gauge (dipstick). Two driver selected modes are
available, sport or normal. The TCM is programmed with cruise, traction, gradient, warm-up and hot
mode features. It also provides an on-board diagnostic capability.
The engine and transmission meet OBDII USA environmental regulations.
Default limp home modes for both engine and transmission are provided.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Engine AJ-V8/5HP24
303-056
Basic Engine
The AJ-V8 is an all new 90° V8 liquid cooled engine that gives refined and effortless performance.
Constructed in aluminum alloy, the AJ-V8 introduces several innovative design features new to Jaguar
engines, the most notable of these being:
• a bedplate
• nikasil coated cylinder bores
• fracture split connecting rods
• variable valve timing
• aluminum alloy valve lifters
• electronic throttle control.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24 Engine
Cylinder Block
ENGINE STRUCTURE
1
The cylinder block is an "enclosed V" design,
which provides an inherently rigid structure with
good vibration levels. Nikasil (a composition of
nickel and silicon) coated cylinder bores provide
good friction, heat transfer and piston noise
levels. A low volume coolant jacket improves
warm-up times and piston noise levels; the
longitudinal flow design of the jacket, with a
single cylinder head coolant transfer port in each
bank, improves rigidity and head gasket sealing.
The right hand cylinder bank is designated as "A"
bank, and the left hand as "B" bank. The cylinder
bores of each bank are numbered from 1 to 4,
starting from the front.
2
3
Engine data is marked at three locations on the
cylinder block. Component diameters are
represented by alphabetical and numerical codes;
keys to the codes are in the Service Manual.
4
1. Cylinder Head
2. Cylinder Block
3. Bed Plate
4. Structural Sump
303-052
ENGINE DATA LOCATIONS
Serial Number
* Main Bearing Crankshaft
Diameters * Connecting
Rod Bearing Crankshaft
Diameters * Cylinder Bore
Diameters * Main Bearing
Bore Diameters *
Emissions Code
303-001
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Engine AJ-V8/5HP24
CYLINDER BLOCK, CRANKSHAFT AND BEDPLATE
303-011
7
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24 Engine
Bedplate
SEALANT TRACK ON BEDPLATE
The bedplate is a structural casting bolted to the
bottom of the cylinder block to retain the
crankshaft. The use of a bedplate further
improves rigidity. Iron inserts, cast into the main
bearing supports of the bedplate, minimise main
bearing clearance changes due to heat
expansion.
Two hollow dowels align the bedplate with the
cylinder block.
Beads of sealant seal the joint between the
bedplate and the cylinder block.
303-012
Crankshaft
CRANKSHAFT REAR OIL SEAL
Six counter-balance weights ensure good
vibration levels from the four throw, five bearing
crankshaft. Manufactured in cast iron, the
crankshaft also has undercut and rolled fillets for
improved strength.
The main bearings are aluminum/tin split plain
bearings. An oil groove in the top half of each
bearing transfers oil into the crankshaft for
lubrication of the connecting rod bearings. A
lead/bronze thrust washer is installed each side of
the top half of the center main bearing.
The crankshaft rear oil seal (a lip seal similar to
that used on the AJ16 engine) is a press fit in the
bedplate to cylinder block interface.
303-013
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Engine AJ-V8/5HP24
Connecting Rods and Pistons
CONNECTING ROD AND PISTON
The connecting rods are manufactured in sinter
forged steel. The bearing caps are produced by
fracturing the opposing sides of the connecting rod at
the bearing horizontal center-line. As well as being
easier to manufacture, when re-assembled the
fractured surfaces interlock to form a strong
seamless joint. The cylinder position is etched on
adjoining sides of the joint to identify matching
connecting rods and bearing caps. The connecting
rod bearings are lead/bronze split plain bearings.
The pistons are of the open ended skirt design with
flat upper surfaces to reduce heat absorbtion. Three
piston rings, two compression and one oil control, are
installed on each piston. Each piston is installed on a
wrist pin located in a lead/bronze bushing in the
connecting rod.
303-014
Sump
SEALANT TRACK ON STRUCTURAL SUMP
The sump consists of an aluminum alloy structural
sump bolted to the bedplate, and a pressed steel oil
pan bolted to the structural sump. A windage tray
attached to the top of the structural sump isolates
the oil pan from the disturbed air produced by the
rotation of the crankshaft, to prevent oil aeration and
improve oil drainage. A rubber plug at the rear of the
structural sump seals the port that provides access to
the torque converter securing bolts. The engine oil
drain plug is located at the front right corner of the oil
pan.
A silicon rubber in-groove gasket seals the joint
between the oil pan and the structural sump; a bead
of sealant seals the joint between the structural
sump and the bedplate.
303-021
9
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24 Engine
STRUCTURAL SUMP AND OIL PAN
Torque
Converter
Access
303-010
Starter and Drive Plate
STARTER MOTOR
The engine starter motor is installed at the rear
right side of the engine, at the cylinder block to
bedplate split line (for further details of the
starter motor see Technical Guide, XK8
Introduction).
The starter drive plate is attached to the rear of
the crankshaft. A timing disc, for the engine
speed sensor, is spot welded to the front face of
the drive plate.
303-062
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Engine AJ-V8/5HP24
TIMING DISC
STARTER DRIVE PLATE
303-035
303-034
The 14 mm spark plugs, one per cylinder, locate
in recesses down the center-line of each cylinder
head.
An engine lifting eye is cast into the front of each
cylinder head (the rear lifting eyes, one on each
cylinder head, are bolt-on tools).
Cylinder Heads
The cylinder heads are unique to each cylinder
bank. Deep seated bolts, to reduce distortion,
secure the cylinder heads to the cylinder block.
Two hollow dowels align each cylinder head with
the cylinder block.
The cylinder head gaskets consist of a silicon
beaded composite gasket with metal eyelets for
the cylinder bores, similar to that on the AJ16
engine.
Each cylinder head incorporates dual overhead
camshafts operating four valves per cylinder via
solid aluminum alloy valve lifters. Steel shims in
the top of the valve lifters enable adjustment of
valve clearances.
The lightweight valve gear provides good
economy and noise levels. Valve head diameters
are 31mm (1.220 in) for the exhaust and 35mm
(1.378 in) for the intake. All valves have 5mm
(0.197 in) diameter stems supported in sintered
metal seats and guide inserts. Collets, valve
collars and spring seats locate single valve
springs on both intake and exhaust valves. Valve
stem seals are integrated into the spring seats.
The camshafts are manufactured in chilled cast
iron. Five aluminum alloy caps retain each
camshaft. Location numbers, 0 to 4 for the intake
camshaft and 5 to 9 for the exhaust camshaft,
are marked on the outer faces of the caps. The
rear of B bank intake camshaft has a timing ring
for the camshaft position sensor. A flat,
machined near the front of each camshaft,
enables the camshafts to be locked during the
valve timing procedure.
CAMSHAFT POSITION SENSOR
TIMING RING
303-054
11
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24 Engine
A BANK CYLINDER HEAD
Exhaust Camshaft
Intake Camshaft
Lifting
Eye
303-047
Timing Gear
Single row primary and secondary chains drive
the camshafts of each cylinder bank. The primary
chains transmit the drive from two sprockets on
the crankshaft to variable valve timing units on
the intake camshafts. The secondary chains
transmit the drive from the variable valve timing
units to sprockets on the exhaust camshafts.
(Continued on Page 14)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Engine AJ-V8/5HP24
TIMING GEAR
Secondary Chain
Tensioner
Primary Chain
Secondary
Chain
Variable Valve
Timing Unit
Primary Chain
Tensioner
303-016 / 017
13
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24 Engine
Timing Gear (Continued)
A key locates the two drive sprockets on the
crankshaft. The crankshaft's torsional vibration
damper retains the sprockets in position.
The variable valve timing units and the exhaust
camshaft sprockets are non-interference, non-
keyed fits on their respective camshafts; the
drive being transmitted by the face to face
friction load produced by the valve timing
unit/sprocket securing bolt.
Each chain has an hydraulic tensioner operated
by engine oil. A jet of oil from the end of each
tensioner lubricates the chains. The primary chain
tensioners act on pivoting flexible tensioner
blades. The secondary chain tensioners act
directly on the chains. Guide rails are installed on
the drive side of the primary chains.
Timing Cover
The aluminum alloy timing cover accommodates
the crankshaft front oil seal (a PTFE lip seal) and
the two variable valve timing solenoids. Silicon
rubber in-groove gaskets seal the joint between
the timing cover and the front face of the engine.
TIMING COVER
Crankshaft
Front Oil
Seal
Variable Valve
Timing Solenoid
303-015
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Engine AJ-V8/5HP24
Camshaft Covers
The camshaft covers are manufactured from vinyl
ester composite. The A bank camshaft cover
incorporates an outlet for the full load engine
breather. The B bank camshaft cover incorporates
the engine oil filler cap and an outlet for the part
load engine breather. Identical oil separators are
incorporated below the breather outlet in each
cover (see Crankcase Ventilation, page 35).
Silicon rubber in-groove gaskets seal the joints
between the camshaft covers and the cylinder
heads. Together with spacers and seals on the
camshaft cover fasteners, they also isolate the
covers from direct contact with the cylinder
heads, to reduce noise.
B BANK CAMSHAFT COVER
303-042
15
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24 Engine
Exhaust Manifold
The thin-wall cast iron manifolds are unique for
each cylinder bank. On engines with EGR, the A
bank manifold has a connection for the transfer
pipe.
Spacers on the securing bolts allow the
manifolds to expand and retract with changes of
temperature while maintaining the clamping
loads.
Heat shields are integrated into the exhaust
manifold gaskets.
EXHAUST MANIFOLD
303-023
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Engine AJ-V8/5HP24
Engine Cooling
The cooling system is a low volume, high velocity
system with good warm-up and temperature
profile characteristics.
CYLINDER BLOCK DRAIN/HEATER
From the pump, the coolant flows into each bank
of the cylinder block. In each bank, 50% of the
coolant cools the cylinder bores and 50% is
diverted through a bypass gallery. At the rear of
the banks the two flows mix and enter the
cylinder heads. The coolant then flows forwards
to the outlet ports. When the thermostat is
closed, the coolant returns directly to the pump
through the bypass on the thermostat housing.
When the thermostat is open, the coolant returns
to the pump via the vehicle's radiator.
A coolant drain plug is installed on the rear left
side of the cylinder block. On vehicles with the
cold climate package, the cylinder block heater
replaces the drain plug.
303-O63
Note: Coolant is drained from the right bank of
the cylinder block by removing the
coolant pipe behind the starter motor.
COOLING SYSTEM DIAGRAM
7
8
2
5
4
1
6
3
7. A/C Heater Supply
8. Bleed Outlet
4. Coolant Pump
5. Thermostat Housing
6. Vehicle Radiator (Reference)
1. Electronic Throttle
2. EGR Valve
3. A/C Heater Return
303-028
17
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24 Engine
Coolant Pump
COOLANT PUMP
The coolant pump is installed between the two
cylinder banks, on the front face of the cylinder
block. The pumping element is a shrouded
composite impeller. Coolant escapes from seal
breather holes in the housing if the pump's
bearing seal fails.
An O-ring and an edge bonded rubber/aluminum
alloy gasket seal the pump to cylinder block
interface. The O-ring seals the inlet port from the
thermostat. The gasket seals the outlet ports into
the cylinder banks.
Thermostat Housing
The composite thermostat housing is installed
between the two cylinder banks, immediately
above the coolant pump. The thermostat controls
the flow of coolant through the radiator. It starts
to open at 80 to 84°C (176 to 183˚F) and is fully
open at 96°C (205˚F).
303-030
A duct in the cylinder block connects the
thermostat housing outlet to the pump inlet. A
stub pipe connects the duct to the air conditioning
heater matrix return line.
THERMOSTAT HOUSING
By-pass
An in-groove gasket seals the joint between the
thermostat housing and the cylinder block.
In addition to containing the thermostat, the
composite thermostat housing incorporates
connections for the bleed, bypass and radiator
bottom hoses. The bleed outlet vents any air in
the system into the vehicle's coolant reservoir.
The cap of the thermostat housing is removable,
to allow air out of the system when filling from
empty.
From
Radiator
Cap
Bleed
CAUTION: Use the correct torque (marked on
the cap) when re-installing the
cap, or the cap/thermostat
housing could be damaged.
A/C Heater
Return
303-029
Coolant Hoses
Supply and return hoses for the air conditioning
heater matrix are installed between the cylinder
banks.
A connection at the rear of A bank provides the
coolant supply for the electronic throttle and the
EGR valve. The outlet from the EGR valve
connects to the return hose of the air conditioning
heater matrix.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Engine AJ-V8/5HP24
COOLANT HOSES
Electronic Throttle
EGR Valve
Electronic Throttle
A/C Heater Matrix
303-032
19
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24 Engine
Coolant Outlet Duct
COOLANT OUTLET DUCT
The composite coolant outlet duct connects to
the outlet port of each cylinder head to provide a
common connection point for the radiator top
hose. It also incorporates connections for the
coolant temperature sensor, the supply to the air
conditioning heater matrix, and the bypass flow
to the thermostat housing.
By-pass
To Radiator
An in-groove gasket seals each of the joints
between the outlet duct and the cylinder heads.
ECT Sensor
A/C Heater
Supply
303-066
Engine Lubrication
Oil is drawn from the reservoir in the oil pan and
pressurised by the oil pump. The output from the
oil pump is then filtered and distributed through
internal oil passages.
All moving parts are lubricated by pressure or
splash oil. Pressurised oil is also provided for
operation of the variable valve timing units and
the timing gear chain tensioners.
The oil returns to the oil pan under gravity. Large
drain holes through the cylinder heads and
cylinder block ensure the quick return of the oil,
reducing the volume of oil required and enabling
an accurate check of the contents soon after the
engine stops.
System replenishment is through the oil filler cap
on the B bank camshaft cover.
With the exception of the pump and level gauge,
all oil system components are installed on the
structural sump.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Engine AJ-V8/5HP24
LUBRICATION SYSTEM
16
15
1
2
14
13
12
11
10
9
3
8
6
4
7
5
1. Valve Lifter Supply
2. Main Bearing Supply
3. Connecting Rod Bearing Supply
4. Bedplate/Cylinder Block Interface
5. Oil Pick-up
6. Pressure Relief Valve
7. Oil Pressure Switch
8. Oil Filter
9. Structural Sump/Bedplate Interface
10. Bedplate/Cylinder Block Interface
11. Oil Pump
12. Primary Chain Tensioner Supply
13. Cylinder Block/Cylinder Head Interface
14. Variable Valve Timing Supply
15. Camshaft Bearing Supply
16. Secondary Chain Tensioner Supply
303-007
21
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24 Engine
Oil Pick-up
OIL PUMP
The moulded composite oil pick-up is immersed
in the oil reservoir to provide a supply to the oil
pump during all normal vehicle attitudes. The
castellated inlet allows the supply to be
maintained even if the sump pan is deformed (eg.
by “grounding”). A mesh screen in the inlet
prevents debris from entering the oil system.
Oil Pump
The oil pump is installed on the crankshaft at the
front of the engine. The pump inlet and outlet
ports align with oil passages in the bedplate. A
rubber coated metal gasket seals the pump to
bedplate interface.
The pumping element is an eccentric rotor, which
is directly driven by flats on the crankshaft. An
integral pressure relief valve regulates pump
outlet pressure at 4.5 bar (65.25 psi).
Oil Filter
The oil filter is a replaceable cartridge installed on
an adapter. An internal bypass facility permits full
flow bypass if the filter is blocked.
303-009
OIL LEVEL GAUGE
Oil Pressure Switch
The oil pressure switch connects a ground input
to the instrument cluster when oil pressure is
present. The switch operates at a pressure of
0.15 to 0.41 bar (2.2 to 5.9 psi).
Oil Level Gauge
The oil level gauge locates midway along the left
side of the oil pan, supported in a tube installed in
the bedplate. Two holes in the end of the gauge
indicate the minimum and maximum oil levels.
There is a difference of approximately 1 liter
(1 US quart) between the two levels.
303-022
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Engine AJ-V8/5HP24
OIL SYSTEM COMPONENTS ON STRUCTURAL SUMP
Pressure Switch
Filter
Pick-up
303-185
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24 Engine
Variable Valve Timing
The variable valve timing system improves low
and high speed engine performance, engine idle
quality and exhaust emission. It is a two position
system that operates on the intake camshafts
only. There are 30° of crankshaft movement
between the retarded and advanced positions.
Engine oil pressure operates the system under
the control of the ECM.
and sprocket assembly to the inner sleeve and,
when moved axially, turn the inner sleeve in
relation to the body and sprocket assembly.
Engine oil pressure (controlled by the valve timing
solenoid) moves the ring gears and piston to turn
the inner sleeve in the advanced timing direction.
A return spring moves the ring gears and piston
to turn the inner sleeve in the retarded timing
direction.
Additional springs absorb backlash to reduce
noise and wear. The springs between the ring
gears absorb rotational backlash. The spring
between the inner sleeve and the end of the
body and sprocket assembly absorbs axial
backlash.
For each intake camshaft there is a valve timing
unit, a bush carrier assembly and a valve timing
solenoid.
Valve Timing Unit
The valve timing unit turns the intake camshaft in
relation to the primary chain to advance and
retard the timing.
The unit consists of a body and sprocket
assembly separated from an inner sleeve by a
ring piston and two ring gears. A bolt secures the
inner sleeve to the camshaft. The ring gears
engage in opposing helical splines on the body
and sprocket assembly and on the inner sleeve.
The ring gears transmit the drive from the body
VALVE TIMING DIAGRAMS
Retarded
TDC
Advanced
TDC
25°
5°
5°
35°
10°
10°
Intake
Intake
Exhaust
Exhaust
65°
50°
50°
35°
BDC
BDC
303-068
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Engine AJ-V8/5HP24
VALVE TIMING UNIT
Body and Sprocket
Assembly
Inner
Sleeve
Return
Spring
Piston
Ring Gears
303-002
Bush Carrier
BUSH CARRIERS
The bush carrier contains oil passages that link
the engine oil supply to the valve timing unit. A
lug on the bush carrier locates in the central bore
of the valve timing unit. Two hollow dowels at
the bush carrier to cylinder block interface ensure
the lug is accurately located. A scarf- jointed fibre
ring seals the joint between the lug and the valve
timing unit. An integral shuttle valve, biased by a
coil spring, controls the flow of oil through the oil
passages.
303-003
25
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24 Engine
Valve Timing Solenoid
VALVE TIMING SOLENOID
The valve timing solenoid controls the position of
the shuttle valve in the bush carrier. A plunger on
the solenoid extends when the solenoid is
energised and retracts when the solenoid is de-
energised.
Operation
When the valve timing solenoids are de-
energised, the coil springs in the bush carriers
position the shuttle valves to connect the valve
timing units to drain. In the valve timing units, the
return springs hold the ring pistons and gears in
the retarded position.
When the valve timing solenoids are energised
by the ECM, the solenoid plungers position the
shuttle valves to direct engine oil to the valve
timing units. In the valve timing units, the oil
pressure overcomes the force of the return
springs and moves the gears and ring pistons to
the advanced position.
303-004
System response times are 1.0 second maximum
for advancing and 0.7 second maximum for
retarding.
While the valve timing is in the retarded mode,
the ECM produces a periodic lubrication pulse.
VARIABLE VALVE TIMING OPERATION
Retarded
Advanced
Engine Oil Pressure
Engine Oil Pressure
303-005
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Engine AJ-V8/5HP24
This momentarily energises the valve timing
solenoids to allow a spurt of oil into the valve
timing units. The lubrication pulse occurs once
every 5 minutes.
Note: With the vehicle stationary and the hood
open, operation of the valve timing
solenoids may be audible when the
lubrication pulse occurs at engine idle
speed.
Air Intake System
Filtered air from the vehicle's intake ducting is
metered by the electronic throttle then directed
through the induction elbow into the intake
manifold.
AIR INTAKE SYSTEM
Electronic
Throttle
Intake
Manifold
Induction
Elbow
303-050
27
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24 Engine
Electronic Throttle
The electronic throttle enables the ECM to
control the flow of air into the engine. It includes:
Vacuum Actuator
On vehicles with cruise control, the vacuum
actuator is connected to manifold vacuum and
controlled by the ECM. On vehicles without
cruise control, the vacuum actuator is open to
atmosphere and the actuator is inoperative.
•
an input shaft that receives driver inputs from
the accelerator pedal via a conventional
throttle cable
•
a mechanical guard, to prevent throttle valve
position exceeding driver demand and to
operate the throttle valve mechanically if the
electronic system fails
Thermostatic Air Valve
The thermostatic air valve is a wax capsule
operated valve that enables engine starting at
low engine temperatures (with the accelerator
pedal in the idle position, the degree of throttle
valve movement available between fully closed
and the mechanical guard is insufficient to start
the engine at low temperatures). The
thermostatic air valve is fully open at a coolant
temperature of approximately -30°C (-22˚F) and
progressively closes until it is fully closed at
+40 °C (+104˚F). A flow of engine coolant
through the throttle body provides the
temperature source to operate the thermostatic
air valve.
•
a vacuum actuator, to operate the mechanical
guard in the cruise control mode of operation
a throttle valve, to regulate the air flow
a thermostatic air valve, to control a bypass
flow around the throttle valve
a dc motor, to operate the throttle valve in
response to inputs from the ECM
three position sensors, to supply the ECM
with the position's of the input shaft (ie.
accelerator pedal), the mechanical guard and
the throttle valve
•
•
•
•
•
springs connected to the input shaft, the
mechanical guard, the throttle valve and the
drive gear of the dc motor.
SIMPLIFIED VIEW OF ELECTRONIC THROTTLE
Mechanical Guard
Mechanical Guard
Position Sensor
Throttle Valve
Position Sensor
Input
Shaft
Accelerator Pedal
Position Sensor
Spring Force
303-080
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Engine AJ-V8/5HP24
ELECTRONIC THROTTLE
Vacuum Actuator
Vent
dc Motor
Coolant
Outlet
Thermostatic
Air Valve
Coolant
Inlet
303-067
Springs
turn the throttle valve and follow the input shaft
and mechanical guard, maintaining a constant
gap between the adjacent levers of the throttle
valve and mechanical guard. The dc motor drive
gears turn the throttle valve in the closed
direction; the throttle valve spring turns the
throttle valve in the open direction and keeps the
throttle valve in contact with the drive gear.
Inputs from the throttle valve position sensor
enable the ECM to exercise closed loop control.
The arrangement of the throttle valve drive
prevents the ECM from exceeding driver
demand, since if the motor is driven fully open
the throttle valve engages the mechanical guard
and disengages from the dc motor drive gears.
The arrangement of the mechanical guard to
throttle valve interface allows the ECM to reduce
throttle opening to less than driver demand, eg.
during stability/traction control or engine power
limiting.
The input shaft spring and the mechanical guard
spring oppose movement in the throttle open
direction, and provide the "feel" of the accelerator
pedal. The throttle valve spring and the drive gear
spring oppose movement in the throttle closed
direction.
Operation
The design of the input shaft and the mechanical
guard, and the bias of their respective springs,
means that, except in cruise control, they always
rotate together. The throttle cable turns them in
the open direction; the springs keep their
adjacent levers locked together and turn them in
the closed direction.
The ECM monitors the position of the input shaft
and mechanical guard using the inputs from the
accelerator pedal and mechanical guard position
sensors. During normal operation, when the ECM
detects any movement it signals the dc motor to
29
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24 Engine
At idle, the ECM controls engine speed using the
accelerating above the set speed, the accelerator
pedal has a lighter "feel" until the input shaft
engages with the mechanical guard again.
restricted throttle valve movement available
between the mechanical guard (open limit) and a
factory set stop on the dc motor drive gear
(closed limit).
Mechanical operation of the throttle valve occurs
if the ECM selects the mechanical guard mode of
operation after detecting a fault. The ECM de-
energizes the dc motor and the throttle valve
spring turns the throttle valve in the open
direction until it engages the mechanical guard.
The input shaft, mechanical guard and throttle
valve are then effectively locked together by their
springs, so that the throttle cable is in direct
control of the throttle valve. When the throttle
valve opens, it turns the dc motor drive gears. On
subsequent closing of the throttle valve the drive
gears remain in the open position, disengaged
from the throttle valve.
When cruise control is engaged, the ECM
calculates the required throttle valve opening and
operates the vacuum system connected to the
vacuum actuator. The vacuum actuator then turns
the mechanical guard to a position that allows the
required throttle valve opening. The inputs from
their respective position sensors allow the ECM
to monitor and adjust the mechanical guard and
the throttle valve to maintain the set speed. As
the driver releases the accelerator pedal, the
input shaft disengages from the mechanical
guard. Note that during cruise control, when
Operating Modes (Refer to the figure, page 31)
Normal
1.
2.
3.
4.
5.
6.
Throttle cable inputs driver demand
Input shaft turns mechanical guard
Sensors supply ECM with inputs of driver demand
ECM operates dc motor
Sensor supplies ECM with inputs of throttle valve position
Gap maintained between throttle valve and mechanical guard
Cruise Control
1.
2.
3.
4.
5.
6.
Vacuum actuator turns mechanical guard
Sensor supplies ECM with mechanical guard position
ECM operates dc motor
Sensor supplies ECM with inputs of throttle valve position
Gap maintained between throttle valve and mechanical guard
Input shaft at idle position, disengaged from mechanical guard
Mechanical Guard
1.
2.
3.
4.
Throttle cable inputs driver demand
Input shaft turns mechanical guard
Mechanical guard turns throttle valve
dc motor drive disengaged from throttle valve
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Engine AJ-V8/5HP24
ELECTRONIC THROTTLE OPERATING MODES
5
4
Normal
6
3
2
4
3
1
1
Cruise Crontrol
5
2
6
4
Mechanical Guard
3
2
Spring Force
1
303-080,/081/082
31
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24 Engine
INDUCTION ELBOW
Fuel Tank Vacuum
and Pressure Relief
Valve Connection
Part Load Breather/
EVAP Valve Vacuum
Connection
Fuel Pressure
Regulator/
Cruise Control
Vacuum
Brake Booster
Vacuum Connection
Connection
303-033
Induction Elbow
SECTION THROUGH INTAKE MANIFOLD
The induction elbow provides the interface
between the electronic throttle and the intake
manifold. Connections on the induction elbow
provide vacuum take-offs for various services. A
boss on the rear of the elbow accommodates the
EGR valve.
Intake Manifold
The intake manifold is manufactured in
composite, with integrated composite fuel rails
and metal thread inserts. Individual ducts lead off
a central chamber to the inlet ports of each
cylinder.
Silicon rubber gaskets, located in channels in the
intake manifold, seal the joints between the ducts
and the cylinder heads.
303-051
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Engine AJ-V8/5HP24
Fuel System
Fuel injectors, controlled by the ECM, are
installed in the fuel rails on each side of the
intake manifold. A cross-over pipe connects the
two fuel rails together at the front of the
manifold. A test valve in the cross-over pipe
allows the fuel rail to be pressurised and
depressurised
troubleshooting.
during
servicing
and
A pressure regulator on the rear of the right fuel
rail controls the pressure in the fuel rails.
A return line directs excess fuel from the
pressure regulator back to the fuel tank.
FUEL SYSTEM
Fuel Injector
Test Valve
Fuel Return
Intake Manifold Pressure
Fuel Pressure Regulator
303-024/059/078/155
33
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24 Engine
Fuel Injectors
FUEL INJECTOR
Eight, side fed, dual straight jet, fuel injectors are
installed in the fuel rails. The injectors are
electromagnetic solenoid valves controlled by the
ECM. Two O-rings seal each injector to manifold
interface. The fuel jets from the injectors are
directed onto the back of the intake valves.
Pressure Regulator
The pressure regulator is a diaphragm operated
valve that regulates fuel rail pressure at 2.9 bar
(42.05 psi) above intake manifold pressure.
303-025
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Engine AJ-V8/5HP24
Ignition System
The ignition system consists of two ECM
controlled ignition amplifier modules, which each
supply four spark plug mounted ignition coils.
The 14 mm spark plugs, one per cylinder, locate
in recesses down the center-line of each cylinder
head.
IGNITION COIL AND SPARK PLUG
The on-plug ignition coils are secured to the
camshaft covers. The engine harness connects
the on-plug ignition coils to the ignition amplifiers
located on the vehicle body. A composite cover
fits over the on-plug coils.
303-049
Crankcase Ventilation
OIL SEPARATOR
The engine is ventilated through a part load and a
full load breather.
The part load breather is a flexible composite
hose connected between the oil separator in B
bank camshaft cover and the induction elbow. A
restrictor in the outlet from the oil separator
prevents reverse flow.
The full load breather is a flexible composite hose
connected between the oil separator in A bank
camshaft cover and the air intake duct.
The ends of the breather hoses incorporate quick
release connectors (see figure, page 36).
The oil separators consist of wire gauze packed
into an open ended enclosure below the breather
outlet.
303-046
35
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24 Engine
CRANKCASE VENTILATION SYSTEM
Part Load Breather Hose Connector
Full Load Breather Hose Connector
303-065/077/079
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Engine AJ-V8/5HP24
EGR System
The EGR system is controlled by the ECM and
consists of an EGR valve and a transfer pipe.
The EGR valve is a 4 pole stepper motor installed
on the rear of the induction elbow. The valve is
cooled by the coolant return from the electronic
throttle.
EGR VALVE AND TRANSFER PIPE
The transfer pipe connects the right exhaust
manifold to the EGR valve.
303-048
37
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24 Engine
Engine Accessories
All engine accessories are rigidly mounted to
improve refinement, ie. there are no shock
mounts.
Accessory mounting brackets on the left and
right sides of the engine support the A/C
compressor/ PAS pump and the generator
respectively. Dowels between the accessory
mounting brackets and the engine ensure the
accessory pulleys are accurately aligned with the
accessory drive belt (for further details of the
accessories see Technical Guide, XK8
Introduction).
ACCESSORY MOUNTING BRACKETS
303-019
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Engine AJ-V8/5HP24
ENGINE ACCESSORIES AND DRIVE BELT
PAS Pump
Generator
A/C
Compressor
303-018
Accessory Drive
AUTOMATIC TENSIONER
Belt Wear
Indicator
A single seven ribbed belt drives all the engine
mounted accessories. The torsional vibration
damper on the front of the crankshaft drives the
belt. An automatic tensioner, located on the left
accessory mounting bracket, keeps the belt at
the correct tension. An idler pulley on the right
accessory mounting bracket increases the wrap
angle around the generator pulley.
Replace Belt
New Belt Maximum Length
New Belt Minimum Length
The torsional vibration damper incorporates
compressed rubber between its inner and outer
diameters to absorb vibration and shock loads.
The automatic tensioner consists of an idler
pulley on the end of a spring loaded pivot arm.
The pivot arm can be turned counter-clockwise
(viewed from the front of the engine) for removal
and installation of the belt. A belt wear indicator
is incorporated on the rear of the pivot arm.
303-020
39
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24 Engine
ENGINE HARNESS
1
20
19
18
3
2
17
4
16
15
5
14
13
6
12
7
8
11
9
10
Connectors
1. PI032, B Bank VVT solenoid
2. PI027, B Bank Knock Sensor
11. PI002, Engine Management Harness (On vehicle)
12. PI001, Engine Management Harness (On vehicle)
13. PI033, Throttle Valve Motor
3. PI004, Engine Coolant Temperature Sensor
4. PI026, A Bank Knock Sensor
5. PI031, A Bank Valve Timing Solenoid
6. PI035, MAFS (On vehicle)
14. PI034, EGR Valve
15. PI015, Camshaft Position Sensor
16. PI042, Accelerator Pedal and Mechanical Guard
Position Sensors
7. PI050, Generator
8. PI040, Oil Pressure Switch
17. PI007-PI010, A Bank Injectors 1-4
PI011-PI014, B Bank Injectors 1-4
9. PI018-PI021, A Bank Ignition Coils 1-4
PI022-PI025, B Bank Ignition Coils 1-4
10. PI006, Throttle Position Sensor
18. PI037, A/C Compressor Lock Sensor
19. PI036, A/C Compressor Clutch
20. PI017, Engine Speed Sensor
303-057
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Engine AJ-V8/5HP24
Engine Harness
The engine harness links engine mounted
electrical components to the vehicle's engine
management harness. The connectors that
interface with the engine management harness
are attached to a bracket on the transmission
housing. Integral nylon fasteners attach the
harness to the engine. Connectors on component
flying leads are attached to engine mounted
brackets.
CONNECTORS ON TRANSMISSION
HOUSING BRACKET
303-061
HARNESS FASTENER
303-064
FLYING LEAD CONNECTOR BRACKET
303-058
41
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24 Engine
Engine Covers
Engine covers are installed over the fuel injectors.
The covers are a push fit, held in position by
mating studs and grommets on the covers and
the engine. The rubber grommets isolate the
covers from the engine to prevent noise. A sleeve
connects the covers together at the rear.
ENGINE COVERS
303-055
MOUNTING POINTS ON ENGINE COVER
303-040
MOUNTING POINTS ON ENGINE
303-039
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Engine AJ-V8/5HP24
Engine Specifications
Configuration
90° V8
Cylinder Head
Valve Clearances (Cold):
Intake
Dual overhead camshafts, 4 valves per cylinder
0.18 to 0.22 mm (0.007 to 0.009 in)
0.23 to 0.27 mm (0.009 to 0.011 in)
NGK PFR5011E (platinum tipped center electrode)
1.0 mm (0.040 in)
1A, 1B, 4A, 2A, 2B, 3A, 3B, 4B
86 mm (3.386 in)
Exhaust
Spark Plug Type:
Spark Plug Gap:
Firing Order
Bore
Stroke
86 mm (3.386 in)
Displacement
Compression Ratio
Maximum Power (DIN)
Maximum Torque (DIN)
Maximum Speed (Limited)
Coolant Type
3.996 liters (244 CDI)
10.75 : 1
216 kW (290 BHP) at 6100 rpm
393 Nm (290 lbf. ft) at 4250 rpm
7100 rpm
Water and Jaguar anti-freeze to specification ESD-M97B49-A
(see Service Manual for mixture ratio)
Coolant Volume:
Engine Only
3.7 liters (0.98 US gallon)
Complete System
Oil Specification:
Oil Volume:
10 liters (2.65 US gallons)
SAE 5W30 - API SH/ILSAC GF-2
6.5 liters (6.88 US quarts)
Approximately 200 kg (441 lb)
Weight (With Accessories)
43
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24 Engine Management
ECM
The engine management system is controlled by
the ECM, which is installed in the control module
enclosure in the engine compartment. The ECM
provides optimum control of the engine under all
operating conditions. It also incorporates a
comprehensive monitoring and diagnostic
capability. Software variations ensure that the
system complies with the latest diagnostic and
emissions legislation of the destination market.
The ECM receives inputs from engine related
sensors and various vehicle systems, and
provides outputs for the following:
ECM
•
•
•
•
•
•
•
•
•
•
•
•
•
•
electronic throttle
fuel pump
fuel injection
ignition
EVAP system
variable valve timing
EGR system
engine starting
HO2S heaters
instrument cluster
A/C compressor clutch
windshield and backlight heaters
radiator cooling fans
diagnostics.
303-118
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Engine Management AJ-V8/5HP24
Inputs and Outputs
Inputs and outputs are directed to and from the ECM through hard-wired connections and the CAN and
ISO 9141/2 (Serial Communication) data buses contained in the engine management harness (for
further information on the data buses, refer to the Technical Guide, XK8 1997 Model Year Introduction).
ECM Pin Connections
Connector/
Pin
Circuit
Pin
Circuit
Pin
Circuit
EM010
021 Sensor 5 V supply (accelerator
pedal position, mechanical
guard position and throttle
position)
001 Ignition supply
002 Load inhibit
003 Windshield/Backlight heater
request
012 ISO 9141/2
(Serial Communication) in (L)
013 ISO 9141/2
(Serial Communication) out (K)
022 EGR ground
023 Signal ground 1
024 Not used
025 CAN in (-)
026 CAN in (+)
004 A/C clutch request
005 Ignition supply
006 OK to fuel (where
incorporated)
014 Parking brake switch
015 Park/Neutral switch
016 EMS control relay
017 Security acknowledged
018 Not used
007 Not used
027 CAN out (-)
008 Not used
019 Not used
028 CAN out (+)
009 Battery supply
010 Brake switch (foot brake on)
011 Brake switch (cancel cruise
control)
020 Sensor ground (ECT, air intake
temperature, accelerator pedal
position, mechanical guard
position and throttle position)
EM011
009 ECT sensor
014 Shield ground (accelerator
pedal position, mechanical
guard position and throttle
position sensors)
015 Accelerator pedal position
sensor 2
001 Cruise control set +/set -
(acceleration/deceleration)
002 Not used
003 ECM programming
004 Cruise control on/off
005 Cruise control resume/cancel
006 Engine crank
010 Throttle position sensor 2
011 Throttle position sensor 1
012 Sensor ground (ECT, air intake
temperature, accelerator pedal
position, mechanical guard
position and throttle position)
013 Mechanical guard position
sensor
016 Accelerator pedal position
sensor 1
007 Not used
008 Sensor 5 V supply (accelerator
pedal position, mechanical
guard position and throttle
position)
EM012
001 EGR valve 1
002 EGR valve 2
003 EGR valve 3
009 Ignition failure amplifier 1
010 A/C clutch relay
011 Not used
017 O2S A (where fitted)
018 MAFS ground
019 MAFS ground
004 EGR valve 4
012 Air intake temperature sensor
013 MAFS
014 HO2S B
020 Not used
021 Not used
022 Shield ground (HO2S and O2S)
005 A/C high pressure switch
006 A/C low pressure switch
007 Not used
015 HO2S A
008 Ignition failure amplifier 2
016 O2S B (where fitted)
45
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24
Engine Management
ECM PIN CONNECTIONS
1
7
12
1
6
1
5
8
10
16
26
34
4
7
11
1
9
14
22
8
11 11
17 17
27 22
13
21
28
1
12
11
22
1
7
6
12
12
18 16
EM014
EM015
EM013
Circuit
EM012
EM011
EM010
303-129
Connector/
Pin
Circuit
Pin
Pin
Circuit
EM013
001 Fuel pump control
002 EMS programming
013 VSV 2
014 Throttle motor relay
025 Ignition amplifier 2A
026 Ignition amplifier 1A
003 Cruise control switch LED
015 Radiator cooling fans, slow
016 Radiator cooling fans, fast
017 Knock sensor B
027 Shield ground (knock, engine
speed and camshaft sensors)
028 Engine speed sensor ground
029 Camshaft sensor ground
030 Not used
031 Ignition amplifier 4B
032 Ignition amplifier 3B
033 Ignition amplifier 2B
034 Ignition amplifier 1B
004
005
006
)
)
)
018 Knock sensor A
007 ) Not used
019 Engine speed sensor
020 Camshaft position sensor
021 Not used
022 Ignition coil relay
023 Ignition amplifier 4A
024 Ignition amplifier 3A
008
009
010
)
)
)
011 VSV 3
012 VSV 1
EM014
001 Throttle motor power
002 Throttle motor power
003 Ignition supply
004 Signal ground 2
005 Throttle motor (+)
006 Throttle motor (+)
007 Throttle motor ground 2
008 Throttle motor ground 1
009 Valve timing ground
010 Power ground (miscellaneous)
011 Throttle motor (-)
012 Throttle motor (-)
EM015
001 HO2S B heater
002 HO2S A heater
003 EVAP valve
004 Injector 3B
005 Injector 2B
006 Injector 4A
007 Injector 1A
008 Valve timing solenoid B
009 Valve timing solenoid A
010 Not used
011 Injector ground (1A, 2B, 3B, 4A)
012 HO2S heaters ground
013 Not used
014 Not used
015 Injector 4B
016 Injector 3A
017 Injector 2A
018 Injector 1B
019)
020) Not used
021)
022 Injector ground (1B, 2A, 3A, 4B)
46
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24
Engine Management
ENGINE HARNESS PIN CONNECTIONS
1
6
5
1
5
4
9
PI001
10
16
22
26
13
10
11
17
23
PI002
27
29
31
35
41
28
30
34
40
46
PI002
47
53
52
57
PI001
303-061/136/137
Engine Harness to Engine Management Harness Pin Connections
Connector/
Pin
Circuit
Pin
Circuit
Pin
Circuit
PI001
016 Valve timing solenoid A
017 Knock sensor A
018 Screen ground (knock sensor A)
019 Knock sensor B
020 Shield ground (knock sensor B)
021 Engine speed sensor ground
022 Engine speed sensor
023 Screen ground (engine speed
sensor)
024 Camshaft position sensor ground
025 Camshaft position sensor
026 Shield ground (camshaft
sensor)
027 Valve timing solenoid B
028 Valve timing solenoids and
MAFS/intake air temperature
sensor supply
029 Not used
030 Injector 1A
036 Injector 2B
037 Injector 3B
038 Injector 4B
039 Ignition coil 4A
040 Ignition coil 1A
041 Ignition coil 3B
042 Ignition coil 2B
043 Ignition coil 4B
044 Ignition coil 3A
001 Throttle position sensor 2
002 A/C compressor lock sensor
ground
003 Throttle position sensor 1
004 Shield ground (throttle
position sensor)
005 ECT sensor
006 Sensor ground (ECT,
accelerator pedal position,
mechanical guard position and
throttle position)
007 EGR valve 4
008 EGR valve 1
009 EGR valve 2
010 EGR valve 3
011 Generator regulator charge
warning
012 Mechanical guard position
sensor
045 Ignition coil 2A
046 Ignition coil 1B
047 EGR valve supply
048 Engine oil pressure sensor
049 Shield ground (accelerator
pedal position and mechanical
guard position sensors)
050 Accelerator pedal position 1
051 Accelerator pedal position 2
052 MAFS
031 Intake air temperature sensor
ground
032 Injector 2A
033 Injector 3A
034 Injector 4A
053 Ignition supply
054 MAFS ground
055 A/C compressor lock sensor
056 MAFS ground
057 Intake air temperature sensor
013 A/C clutch
014 Sensor 5 V supply (accelerator
pedal position, mechanical
guard position and throttle
position)
035 Injector 1B
015 Not used
47
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24
Engine Management
Connector/
Pin
Circuit
Pin
Circuit
Pin
Circuit
PI002
006 Throttle motor (-)
007 Throttle motor (+)
011 Not used
012 Generator regulator supply
013 Not used
001
)
002 ) Not used
003
004
008
009 ) Not used
010
)
)
)
)
005 Injector supply
CAN Messages
Messages on the CAN data bus used or output by the ECM are detailed below:
Note: This list does not include network monitoring or diagnostic related messages.
Message Used by ECM
Source/Used by
Message Produced by ECM
ABS MALFUNCTION
Brake control module
BRAKE PEDAL PRESSED
ENGINE MALFUNCTION
ENGINE SPEED
ESTIMATED ENGINE TORQUE
PEDAL POSITION
FAST TORQUE REDUCTION CYLINDER
FAST TORQUE REDUCTION IGNITION
FRONT LEFT WHEEL SPEED
FRONT RIGHT WHEEL SPEED
REAR LEFT WHEEL SPEED
REAR RIGHT WHEEL SPEED
TORQUE REDUCTION THROTTLE
TRACTION STATUS
THROTTLE POSITION
TRACTION ACKNOWLEDGE
VEHICLE REFERENCE SPEED
FUEL LEVEL
Instrument cluster
BRAKE PEDAL PRESSED
ENGINE COOLANT TEMPERATURE
ENGINE MALFUNCTION
ENGINE SPEED
HEADLAMP HIGH BEAM STATUS
HEADLAMP LOW BEAM STATUS
SIDE LAMP STATUS
FUEL USED
PARK BRAKE STATUS
THROTTLE MALFUNCTION AMBER
THROTTLE MALFUNCTION RED
GEAR POSITION ACTUAL
GEAR POSITION SELECTED
GEAR SELECTION FAULT
TCM
CRUISE CONTROL STATUS
ENGINE SPEED
ESTIMATED ENGINE TORQUE
PEDAL POSITION
KICKDOWN STATUS
TORQUE CONVERTER SLIP
TORQUE CONVERTER STATUS
TORQUE REDUCTION REQUEST
TRANSMISSION INPUT SPEED
TRANSMISSION MALFUNCTION
TRANSMISSION OIL TEMPERATURE
TRANSMISSION OUTPUT SPEED
TRANSMISSION OVERLOAD
THROTTLE POSITION
TORQUE REDUCTION ACKNOWLEDGE
48
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24
Engine Management
Sensors
OXYGEN SENSORS
Engine management sensors that input to the
ECM are detailed below:
Barometric Pressure Sensor
The barometric pressure sensor is installed in the
ECM. It senses ambient pressure in the engine
management enclosure of the engine
compartment.
H02S
HO2S
A HO2S is installed in the intake end of each
catalytic converter. They provide inputs
proportional to the oxygen content of the exhaust
gases leaving the engine. The heater elements
improve the response time of the sensors during
engine warm-up.
O2S
An O2S is installed in the outlet end of each
catalytic converter. They provide inputs
proportional to the oxygen content of the exhaust
gases leaving the catalytic converter.
02S
303-119
Intake Air Temperature Sensor
The intake air temperature sensor is a thermistor
integrated into the same housing as the MAFS, in
the intake duct immediately downstream of the
intake air cleaner. It provides an input inversely
proportional to the temperature of the air in the
duct.
MAFS/INTAKE AIR TEMPERATURE SENSOR
MAFS
The MAFS is a hot wire sensor that provides an
input which is (approximately) proportional to
mass air flow into the engine.
303-128
49
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24
Engine Management
Camshaft Position Sensor
The camshaft position sensor is installed in B
bank cylinder head at the rear of the intake
camshaft. It is a variable reluctance sensor that
provides an input of intake camshaft position.
ECT Sensor
The ECT sensor is installed in the coolant outlet
duct. It provides an input of coolant temperature
at the cylinder head outlets.
Engine Speed Sensor
The engine speed sensor is installed at the rear
of the bed plate. It is a variable reluctance sensor
that provides an input of engine crankshaft speed
and position.
Knock Sensors
The knock sensors are installed in the cylinder
block on the inboard side of each cylinder bank.
They are piezo-electric sensors that provide
inputs to detect and locate detonation during
combustion.
Accelerator Pedal Position Sensor
ELECTRONIC THROTTLE SENSORS
The accelerator pedal position sensor is
connected to the input shaft in the electronic
throttle. It is a dual track potentiometer that
provides inputs of driver demand at the
accelerator pedal.
Accelerator Pedal Position
and Mechanical Guard
Position Sensors
Mechanical Guard Position Sensor
Throttle Position
Sensor
The mechanical guard position sensor is a single
track potentiometer connected to the mechanical
guard in the electronic throttle. It provides an
input of the position of the mechanical guard.
Throttle Position Sensor
The throttle position sensor is a dual Hall effect
sensor in the motor end of the electronic throttle.
It provides inputs of the position of the throttle
valve.
303-090
50
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24
Engine Management
ENGINE SENSORS
Knock Sensors
ECT Sensor
Camshaft Position Sensor
Engine Speed Sensor
303-127
51
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24
Engine Management
ENGINE MANAGEMENT SCHEMATIC
ECM Inputs and Outputs
1. Intake Air Temperature Sensor
2. MAFS
3. Throttle Position Sensor
4. (Throttle) dc Motor
5. EGR Valve
1
6. Fuel Injector
7. Camshaft Position Sensor
8. On-plug Ignition Coil
9. H02S
2
12 13
10. 02S
11. Engine Speed Sensor
12. Accelerator Pedal Position
Sensor
13. Mechanical Guard Position
Sensor
3
4
M
14. ECT Sensor
15. Knock Sensors
5
6
6
7
8
8
14
15
9
9
10
10
11
303-130
52
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24
Engine Management
Electronic Throttle
The electronic throttle enables the ECM to
perform the following functions:
•
•
•
headlamps and side lamps
windshield and backlight heaters
radiator cooling fans.
•
•
•
•
engine air flow (ie. power) control
engine idle speed control
vehicle cruise control
stability/traction control (in response to
ABS commands)
The ECM detects gear shifts, headlamp status
and side lamp status from their related status
messages on the CAN data bus. The ECM
directly controls the A/C compressor clutch and
the radiator cooling fans. The windshield and
backlight heaters are controlled by the ACCM
upon consent of the ECM via the heater
request/load inhibit circuits.
•
•
•
engine power limiting
vehicle speed limiting
reverse gear torque reduction
If a fault develops in the idle control function, the
ECM goes to open loop control. During open loop
control, rpm is within +100 and -0 rpm of the
target speed for a warm engine (ie. when the
coolant temperature is >30 ˚C (86˚F).
Engine Air Flow Control
During normal operation, when the accelerator
pedal is above idle, the ECM positions the
throttle valve in response to the inputs from the
accelerator pedal position sensor. The throttle
valve follows or leads at a minimum distance the
mechanical guard as the guard is moved by the
accelerator pedal. Thus engine power output is
directly related to driver demand. With the
engine running, the time for the throttle to travel
from idle to fully open is approximately 120 ms
maximum, and from fully open to idle
approximately 140 ms maximum.
Idle Target Speeds
Intake Air Temperature, ˚C (˚F)
Engine Speed, (rpm)
Drive/Reverse
Park/Neutral
>-10 (14)
600 25
625 25
650 25
675 25
650 25
675 25
700 25
725 25
-10 to >-20 (14 to >-4)
-20 to >-30 (-4 to >-22)
≤-30 (≤-22)
Idle Speed Control
During engine idle speed control, the ECM
operates in a closed speed control loop to
maintain a given target idle speed. The ECM
uses gear selection, intake air temperature and
battery voltage to determine the required target
idle speed.
Gear selection is derived from the input of the
Park/Neutral switch in the transmission rotary
switch.
Battery voltage is monitored and, if low voltage is
detected (11.8 V and below), target idle speeds
are increased by up to 50 rpm to increase the
output from the generator.
When the ECM selects a change of target idle
speed, overshoot is kept to 50 rpm maximum.
Certain vehicle services/functions cause a
significant change in engine load as they are
selected on and off. To minimize the effect on
idle speed, the ECM anticipates the change in
load rather than correct the subsequent change in
rpm. The services/functions the ECM anticipates
load changes for are:
•
•
A/C compressor clutch
gear shifts between Park/Neutral and
Reverse/Drive
53
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24
Engine Management
Vehicle Cruise Control
CRUISE CONTROL MASTER SWITCH
The ECM operates the vehicle cruise control
system, in all forward gears, in response to driver
inputs through the master, SET+, SET-, CANCEL
and RES switches.
When the master switch is pressed, two 12 V
ignition supplies are connected to the ECM, one
direct and one via the brake switch. The LED in
the switch comes on to indicate the system is
armed.
With the system armed, a momentary press of
either the SET+ or the SET- switch engages
cruise control, provided the vehicle speed is
28 km/h (17.5 mph) or above. The ECM
memorizes the current road speed as the `set’
speed and signals the vacuum system to operate
the mechanical guard. The inputs from the
position sensors in the electronic throttle allow
the ECM to monitor and adjust the mechanical
guard and the throttle valve to maintain the set
speed.
303-132
CRUISE CONTROL STEERING WHEEL
SWITCHES
The vacuum components are installed in a line
connected between the induction elbow and the
vacuum actuator on the electronic throttle. In the
vacuum system:
•
the check valve isolates the system from
the induction elbow at wide open throttle
when there is little or no vacuum available
the reservoirs extend the time (to
approximately 20 minutes) that, at wide open
throttle, sufficient vacuum can be maintained
in the system to operate the vacuum
actuator
•
303-131
•
•
VSV 1 regulates the vacuum applied to the
vacuum actuator to control the position of
the mechanical guard
VSV 2 connects the vacuum actuator to
atmosphere to release the mechanical guard
when cruise control is disengaged
•
•
VSV 3 is a back-up for VSV 2 (because cruise
control disengagement is safety critical)
filters on the atmospheric ports of VSV 2 and
VSV 3 prevent moisture ingress.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
CRUISE CONTROL SCHEMATIC
B+ Ignition
Driver’s Facia Fuse Box
To Dimmer Switch
F14
ECM
Accelerator Pedal
Position and
Mechanical Guard
Position Sensors
Brake
Cancel
Switch
Master Switch
Ignition Switched
Ground
Brake
VSV 2
Throttle Valve
Switch
Position Sensor
Steering Wheel
Switches
SET+
SET-
VSV 3
VSV 1
CANCEL
RES
M
Vacuum
Actuator
dc Motor
Parking
Brake
Switch
Check Valve
Engine
Speed
Sensor
-VEHICLE SPEED
-TRACTION STATUS
-GEAR POSITION SELECTED
Reservoirs
CAN
303-133
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24
Engine Management
Once cruise control is engaged, a further
momentary press of the SET+ or SET- switch
increments or decrements the set speed by
1.6 km/h (1.0 mph). The ECM then accelerates or
decelerates the vehicle to the new set speed.
The ECM stores a maximum of five incremental
or decremental commands at any one time. Once
the ECM has actioned the first stored command,
a further command can be added. On momentary
operation of the opposite sense switch, the ECM
deletes the last command from memory.
Pressing and holding the SET+ or SET- switch
causes the ECM to increase or decrease the set
speed, and smoothly accelerate or decelerate the
vehicle, until the switch is released. To protect
against switch failure in the closed position, if
either switch is held for longer than 10 minutes,
the ECM disables cruise control until the next
ignition cycle.
The throttle pedal can be used to accelerate the
vehicle beyond the set speed, without
disengaging cruise control (since the diaphragm
actuator is holding the mechanical guard, there is
a noticeable reduction in accelerator pedal load
up to the point at which the input shaft in the
electronic throttle begins to turn the mechanical
guard). When the pedal is released the ECM
returns the vehicle to the set speed in a
controlled manner. Alternatively, a momentary
press of the SET+ or SET- switch causes the
increased vehicle speed to be adopted as the
new set speed.
The ECM disengages cruise control, immediately
returns control of the throttle to the driver and
retains the set speed in memory, if any of the
following occur:
•
•
the brake pedal is pressed
the vehicle decelerates too fast (ie. as
under heavy braking, to guard against
sticking contacts in the brake switch)
the gear selector moves to neutral, park
or reverse
after resuming cruise control the vehicle
accelerates to only 50% of the set speed
(eg. due to a steep hill)
•
•
•
•
the stability/traction control system
operates
vehicle speed decreases below 26 km/h
(16 mph).
On receipt of an input from the RES switch, if a
set speed is stored in the ECM memory, the
cruise control function is re-engaged and the
vehicle accelerated or decelerated to resume the
set speed in a controlled manner.
The ECM continuously monitors the cruise
control switches. If a switch fails closed, on the
initial failure the input is treated as a driver
command and the system responds accordingly.
However, after subsequent disengagement then
re-engagement of the system, the input from the
failed switch is diagnosed as a fault. On detection
of a switch fault, operation of cruise control is
inhibited until the fault is corrected.
The ECM also conducts internal checking
procedures to ensure that only permitted outputs
are generated for given input conditions.
On receipt of an input from the CANCEL switch,
the ECM disengages cruise control and clears the
set speed from memory. Disengagement is in a
controlled manner to provide a smooth return of
throttle control to the driver.
The ECM disengages cruise control, clears the
set speed from memory and immediately returns
control of the throttle to the driver if any of the
following occur:
•
the master switch is pressed, to switch the
system off
•
a fault is detected in the electronic throttle
system, the brake switch or the cruise
control switches
•
•
the parking brake is applied
the engine overspeeds.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24
Engine Management
CRUISE CONTROL VACUUM SYSTEM
Reservoirs
Check Valve
VSV 2
VSV 1
VSV 3
303-121
Stability/Traction Control
If the CAN- TORQUE REDUCTION THROTTLE
message from the brake control module requests
torque reduction, the ECM reduces the throttle
valve opening. It also changes the CAN-
TRACTION ACKNOWLEDGE message to confirm
that torque reduction is in progress.
Engine Power Limiting
If the TCM detects a fault in the transmission, it
changes the CAN- TRANSMISSION OVERLOAD
message to request an engine torque limit. The
ECM then limits throttle valve opening to 18˚
maximum in all forward gears.
Vehicle Speed Limiting
The ECM uses throttle control to limit the
vehicle's maximum speed to 248 km/h (155
mph).
Reverse Gear Torque Reduction
When reverse gear is selected the CAN-
TRANSMISSION OVERLOAD message from the
TCM requests an engine torque limit. The ECM
then limits throttle valve opening to 18˚
maximum.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24
Engine Management
Fuel Injection
The ECM operates eight injectors to provide the
engine with fuel. The amount of fuel required is
determined from a base air:fuel ratio which is
then adjusted for specific operating conditions.
The ECM varies the number and duration of
injector pulses per engine cycle to regulate the
fuel flow. Injector timing is synchronised with
engine rotation, except during starting and
acceleration.
Feedback signals from the two HO2S in the
vehicle's exhaust system enable the ECM to
exercise closed loop fueling control and adaptive
fueling. Separate channels in the ECM control
each bank of injectors.
FUEL PUMP CONTROL
B+ Battery
B+ Ignition
Fuel Pump
Relay
Adaptive fueling accommodates engine efficiency
variations, system tolerances and engine ageing.
Adaptations are produced at idle speed and four
other points through the RPM/load range, on a
fully warm engine, when the adaptive fueling
function centralizes the feedback range. The ECM
retains the adaptations in memory, for use in
subsequent driving cycles. If the difference
between the new and previous adaptations is
excessive, a DTC is logged in the ECM memory.
If the battery supply to the ECM is disrupted (eg.
battery disconnection), the adaptations are lost
from memory. On restoration of the battery
supply, engine operation may be uneven until the
adaptations are restored, especially at idle speed.
The two O2S in the vehicle's exhaust system
provide inputs which enable the ECM to monitor
the efficiency of the downpipe catalytic
converters. These inputs also enable the ECM to
modify the HO2S inputs, to optimise the life of
the catalytic converters.
Trunk
F7
ECM
Fuse Box
Fuel Pump
303-134
Fuel Pump
An output from the ECM controls the relay that
operates the fuel pump. At ignition on, the pump
will operate for 2 seconds without the ignition
switch being set to crank, after which time the
pump will be de-energized. Similarly, if the engine
stops with the ignition on, the pump will be de-
energized after 2 seconds. The pump operates
continuously while the ignition switch is set to
crank, or to on with the engine running.
Base Fuel Map
The ECM contains a base fuel map that corrects
the base air:fuel ratio to the optimum mixture for
a nominal engine throughout the engine speed
and load ranges.
Battery Voltage Correction
Fuel flow through the injectors changes with
voltage, so the ECM monitors their supply
voltage and compensates for any variation from
the nominal.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24
Engine Management
Starting
Engine Overspeed Protection
The fueling start strategy operates independent
of accelerator pedal position or movement, with
the exception of a wide open throttle. The ECM
produces steady state running at the target idle
speed within 2 seconds of firing, after an
overshoot of 200 to 300 RPM maximum.
If the accelerator pedal demands a wide open
throttle during cranking, the ECM disables fuel
injection (and signals the throttle valve to the fully
open position) to clear the fuel vapor from a
"flooded" engine.
The ECM disables fuel injection if engine speed
reaches 7100 RPM. Fuel injection is re-instated
when RPM falls to 7050.
Stability/Traction Control
If the CAN-FAST TORQUE REDUCTION
CYLINDER message from the BCM requests fuel
intervention, the ECM reduces engine torque by
disabling fuel injection until the throttle valve
reaches its required torque reduction position. It
also
changes
the
CAN-TRACTION
ACKNOWLEDGE message to confirm that torque
reduction is in progress.
Warm-up Enrichment
During engine warm-up, the ECM determines the
fuel required from maps which modify an
enrichment factor for coolant temperature,
engine speed and load.
Transient Fueling
During acceleration and deceleration, the ECM
adjusts fueling to optimise the air:fuel ratio for
exhaust emission, response and economy. This
function operates over the full temperature range
for all acceleration and deceleration rates.
Ignition
The ECM supplies two ignition amplifier
modules, which each supply four spark plug
mounted ignition coils. The ECM varies the
ignition timing to optimise power, emissions and
driveability at all operating conditions.
A diagnostic signal from each amplifier module
enables the ECM to monitor the supply to each
ignition coil. If the ECM detects a failure it
disables fuel injection to the affected cylinder.
Full Load Enrichment
At full load, the ECM inhibits closed loop fueling
and increases the fuel supply to enrich the air:fuel
ratio. Full load is derived from throttle valve
position and engine speed. The degree of
enrichment is dependent on engine speed.
Over-run Fuel Cut-off
IGNITION AMPLIFIER MODULES
When the throttle is closed at high engine
speeds, the ECM disables fuel injection until the
engine is at a lower speed. The speeds at which
fuel injection is disabled and re-instated are
mapped against coolant temperature.
On re-instatement the ECM uses a lean air:fuel
ratio, to provide a smooth transition between the
two states, which it then progressively returns to
the nominal. The initial injector pulses are given a
correction value to compensate for cylinder wall
wetting. The ECM derives the air:fuel ratio for re-
instatement from throttle valve position and
engine speed.
During over-run fuel cut-off, operation of the
EVAP valve, EGR valve (where fitted) and closed
loop fueling are inhibited.
303-091
59
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24
Engine Management
changes the CAN-TORQUE REDUCTION
ACKNOWLEDGE message to the TCM to trigger
the gear shift.
Base Ignition Map
A base ignition map contains optimum timing for
a nominal engine throughout the engine speed
and load ranges. Corrections are then added to
adjust for specific operating conditions.
Transient Interaction
A correction is applied to the ignition timing
during throttle transients. The correction is
against rate of change for both opening and
closing of the throttle.
Temperature Corrections
Corrections are added to the ignition timing to
compensate for variations in intake air
temperature and engine coolant temperature.
Stability/Traction Control
If the CAN-FAST TORQUE REDUCTION
IGNITION message from the BCM requests
ignition intervention, the ECM retards the ignition
by the amount requested until the throttle valve
reaches its required torque reduction position. It
Knock Control
Between 700 and 6800 RPM, the ECM retards
the ignition timing of individual cylinders if it
detects detonation. Also, during acceleration at
critical load and speed conditions, the ECM
retards the ignition timing to prevent the onset of
detonation.
also
changes
the
CAN-TRACTION
ACKNOWLEDGE message to confirm that torque
reduction is in progress.
Full Load Advance
At full load, the ECM advances the ignition timing
at the same time as fuel enrichment is applied.
The degree of advancement is dependent on
engine speed.
EVAP System
The ECM operates the EVAP valve to purge the
fuel vapor from the carbon canister. Purge rates
(ie. the amount the EVAP valve opens) are a
function of engine operating conditions and the
vapor concentration level.
Fuel Cut-off Interaction
Immediately prior to over-run fuel cut-off, the
ECM retards the ignition timing to provide a
smooth transition between the two states. On
fueling re-instatement the ECM progressively
returns the ignition timing to the nominal.
Throttle valve position and engine speed
determine the rate at which the timing is returned
to the nominal.
The engine operating conditions that affect the
purge rate are:
•
•
•
•
speed and load
coolant temperature
time from start-up
closed loop fueling.
To determine the vapor concentration level, the
ECM applies stepped opening signals to the
EVAP valve and monitors the subsequent fueling
correction. This is usually performed prior to
purging, so that when purging starts, the EVAP
valve can immediately be set to the optimum
position. If the ECM is unable to determine the
vapor concentration before purging, it uses a
default value which it then modifies while purging
is in progress. During purging, the ECM applies a
correction to the basic fueling calculation based
on the vapor concentration level.
Starting
The ECM incorporates separate timing values for
starting.
EGR
The ignition timing is advanced while the EGR
system is active. The degree of advancement is
dependent on engine speed and load.
Gear Shift Management
When the TCM decides a gear shift is necessary,
it requests a percentage torque reduction using
the CAN - TORQUE REDUCTION REQUEST
message. The ECM then retards the ignition
timing sufficient to achieve the torque reduction
requested. As the ECM retards the ignition, it
Purging is inhibited during fuel cut-off and
stability/traction control fueling intervention.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24
Engine Management
Variable Valve Timing
The ECM energizes the valve timing solenoids to
advance the intake valve timing and de-energizes
them to retard it.
VARIABLE VALVE TIMING MAP
The ECM uses engine load and speed maps to
decide when to advance and retard the timing.
The maps incorporate hysteresis for both engine
load and speed to prevent "hunting".
Between 1250 and 4500 RPM (nominal), at
engine loads greater than approximately 25 % of
the maximum, the timing is advanced. At low
engine loads and at the two ends of the RPM
range, the timing is retarded.
System operation is inhibited at engine coolant
temperatures below -10˚C (14˚F). System
operation is monitored using the input from the
camshaft position sensor. If a fault is detected
the ECM defaults to the retarded (de-energized)
condition.
EGR System
2
3
4
5
6
7
1
Engine Speed, RPM x 1000
The ECM operates the 4 pole stepper motor in
the EGR valve to control the recirculation of
exhaust gases. Unlike previous systems, there
are no temperature or position feedback signals
from the valve. The ECM monitors EGR operation
using changes of mass air flow.
Retarded Advanced
303-135
Engine Starting
At ignition on, if the gear selector is in Park or
Neutral, the ECM enables the fuel injection and
ignition functions. It also outputs a hard wired
digital security acknowledge signal to the BPM to
enable engine cranking. While the engine cranks,
the BPM outputs a hard wired digital engine
cranking signal to the ECM, which employs
engine starting strategies for the duration of the
signal.
If the gear selector is not in Park or Neutral at
ignition on, the ECM inhibits the fuel injection and
ignition functions, and withholds the security
acknowledge signal to prevent cranking.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24
Engine Management
H02S Heaters
Windshield and Backlight
Heaters
The ECM energizes the heater elements of the
HO2S during engine warm-up to shorten the time
it takes for them to produce accurate outputs.
When the windshield heaters and/or the
backlight heater are requested on, the A/CCM
sends a screen request signal to the ECM.
Provided the engine is not at idle speed, the
coolant temperature is not above 119˚C (246˚F)
and the throttle valve is not fully open, the ECM
takes no action and the A/C control module
subsequently energizes the heaters.
If the engine is at idle speed, the coolant
temperature is above 119˚C (246˚F) or the throttle
is fully open, the ECM outputs the load inhibit
signal (the same one as used for the A/C
compressor clutch operation) to the A/CCM to
delay energising the heaters. At idle speed the
delay is only momentary while idle speed
compensation is implemented, after which the
load inhibit signal is removed. At coolant
temperatures above 119˚C (246˚F) or with a fully
open throttle, the delay is for the duration of the
inhibiting condition.
Instrument Cluster
The instrument cluster uses CAN messages from
the ECM to operate the trip computer,
tachometer, engine coolant temperature gauge
and the BRAKE, CHECK ENG and general
warning lamps.
Note: The CHECK ENG lamp is commonly
known as the MIL.
A/C Compressor Clutch
Operation of the A/C compressor clutch is
controlled by the ECM, to prevent unnecessary
loads on the engine during unfavorable operating
conditions.
On receipt of an A/C request signal from the
A/CCM, the ECM immediately energizes the A/C
compressor clutch relay provided the engine is
not at idle speed, the coolant temperature is not
above 119˚C (246˚F) and the throttle valve is not
fully open. When the A/C compressor clutch relay
energizes, the relay output is sensed by the
A/CCM, confirming that the A/C compressor
clutch is engaged.
If the engine is at idle speed, the coolant
temperature is above 119˚C (246˚F) or the throttle
is fully open, the ECM outputs a load inhibit
signal to the A/CCM and delays energising the
A/C compressor clutch relay. At idle speed the
delay is only momentary (in the order of 50 ms)
while idle speed compensation is implemented,
after which the load inhibit signal is removed. At
coolant temperatures above 119˚C (246˚F) or with
a fully open throttle, the delay is for the duration
of the inhibiting condition.
Similarly, with the heaters already energized, if
the engine coolant temperature exceeds 119˚C
(246˚F) or the throttle goes to fully open, the
ECM outputs the load inhibit signal to the A/CCM
and the heaters are de-energized until the
inhibiting condition is removed.
Radiator Cooling Fans
The ECM monitors inputs from the A/C single
and triple pressure switches, and from the ECT
sensor on the engine, to control the operation of
the two radiator cooling fans. Outputs from the
ECM control two relays contained in the radiator
fans module, to operate the fans in off, slow or
fast mode. In the slow mode the fans are
connected in series; in the fast mode the fans are
connected in parallel. Hysteresis in the
temperature and pressure switching values
prevents "hunting" between modes.
Similarly, with the A/C compressor clutch relay
already energized, if the engine coolant
temperature exceeds 119˚C (246˚F) or the
throttle goes to fully open, the ECM de-energizes
the A/C compressor clutch relay and outputs the
load inhibit signal to the A/CCM until the
inhibiting condition is removed.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24
Engine Management
To counteract the increase in engine coolant
temperature that occurs after the engine stops,
at ignition off:
•
if the fans are already on, the ECM keeps
them on for 5 minutes, or until the ECT
decreases to a pre-determined value,
whichever occurs first
•
if the fans are off, the ECM determines, from
ECT and intake air temperature inputs, if the
fans need to be switched on. If they do, it
switches them on for 5 minutes, or until the
ECT decreases to a pre-determined value,
whichever occurs first.
Radiator Fan Switching Points
Mode
Coolant Temperature, ˚C (˚F)
A/C System Pressure, Bar (psi)
On
Off
On
Off
Slow
Fast
90 (194)
86 (187)
12 (174)
22 (319)
8 (116)
17.5 (254)
97.5 (207.5)
93.5 (200.5)
Diagnostics
The ECM performs self test routines and
monitors engine functions, inputs and outputs to
ensure correct operation of the engine and the
engine management system. Hard wired inputs
and outputs are monitored for short and open
circuits, and sensor inputs are also monitored for
range.
Additional checks are run on the more critical
sensor inputs to ensure their validity. Some of the
more critical inputs have substitute or default
values which the ECM adopts if the input is
diagnosed as faulty.
To prevent false DTC being logged, the
monitoring of some inputs and engine functions
is inhibited while the vehicle is above a given
altitude:
•
at altitudes of 2438m (8000ft) and
above,the ECM inhibits diagnostics on:
EGR valve and EGR flow; EVAP valve and
EVAP purge flow; idle speed control; misfire
detection; catalytic converter efficiency.
at altitudes of 2652m (8700ft) and
above, the ECM also inhibits diagnostics on:
HO2S; MAFS; O2S.
•
Any faults detected are logged in the ECM
memory as DTC. The ECM also outputs engine
malfunction messages on the CAN and adopts a
default mode of operation. Most default modes
retain some degree of engine operation (limp
home).
The ECM also stores OBD II related DTC
detected by other control modules on the CAN.
Non-OBD II related DTC are retained in the
memory of the control module that detects the
fault.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24
Engine Management
Additional Input Checks
Input
Additional Strategy
Action, Substitute or DefaultValue
Accelerator pedal
position (x 2) and
mechanical guard
position
Accelerator pedal position input 1 compared to
accelerator pedal position input 2.
Both accelerator pedal position inputs compared to
mechanical guard position input.
If one input fails, the input of the other
two is used.
If two inputs fail, ECM adopts fixed
throttle mode.
Throttle position
(x 2)
1 compared to input 2.
If either input fails, ECM adopts
mechanical guard mode of operation.
Input 1 compared to target value (target value
depends on operating mode, eg. normal running,
cruise control, traction active).
Engine coolant
temperature
After engine start, checks that expected
temperature increase occurs, then monitors for
excessive temperature decrease.
If fault detected, uses substitute value
derived from transmission oil
temperature.
Mass air flow
Compares input with predicted air flow (derived
from a map of throttle angle against engine speed).
If fault detected, uses throttle angle as
load measurement.
Intake air
temperature
Monitors for too fast change of input and for fixed
input.
If fault detected, uses a fixed intake air
temperature of 50˚C (122˚F).
Default Modes
Mode
Effect
General
Warning
Lamp
CHECK
ENG
Lamp (MIL)
Message
Engine shutdown
Fixed throttle
Activates fuel cut-off to stop engine
Red
Red
On
On
ENGINE FAULT
ENGINE FAULT
Fixed throttle valve angle of approximately 2.5˚
set, producing maximum engine speed (unloaded)
of approximately 1200 RPM.
Mechanical guard
Engine speed increases as throttle valve goes to
mechanical guard position; idle speed increases to
approximately 1400 RPM; full throttle available
Red
On
ENGINE FAULT
Engine speed
limiting
Engine speed limited to 3000 RPM
Amber
Amber
None
On
Off
On
ENGINE FAULT
ENGINE FAULT
None
Redundancy
Substitute or default value adopted; no noticeable
difference in performance
Exhaust emission
Substitute or default value adopted; potential
difference in performance
Note: In mechanical guard mode, fuel intervention smooths the transition from normal to default mode, to prevent sudden
acceleration of the vehicle. Also, fuel intervention limits idle speed. Without fuel intervention idle speed would be
approximately 2000 RPM and cause excessive shock loads on the transmission when shifting out of Park or Neutral.
When engine load increases, idle speed fuel intervention is progressively withdrawn.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24
Transmission
Introduction
The new ZF 5HP24 automatic transmission system features five forward gears and one reverse gear.
It also features a filled-for-life oil system. Gearshift management is achieved using a Transmission
Control Module (TCM).
TRANSMISSION
Rotary Switch Connector
Rotary Switch and Oil Inlet Pipe
Level/Filler Plug
Oil Outlet Pipe and Selector Cable
307-012
65
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24
Transmission
Tecnical Data
Transmission weight
including fluid and
torque converter
Oil Type
Oil Capacity
Gear Ratios
in the transmission casing are the input shaft
speed sensor (turbine speed) and output shaft
speed sensor (vehicle speed). The torque
converter is a lightweight unit which, because of
its low mass, improves engine responsiveness.
The torque converter bell housing is bolted to the
transmission casing. Mounting of the
transmission is conventional by bolting the torque
converter bell housing to the engine. The rear
extension housing is bolted to the transmission
casing and forms the rear engine/transmission
mounting point. It also carries the output shaft oil
seal.
The electro-hydraulic module contains three
solenoid valves and five pressure regulators for
gear shifting. Each of the three solenoid valves
control the flow of transmission fluid to the
selected clutches. One pressure regulator serves
as master pressure control for the entire system
and one is used exclusively for torque converter
clutch lock-up operation.
Replacement transmission units are shipped
complete with the torque converter and housing,
extension housing, coupling flange and rotary
position switch. They are also fully filled with
10 liters (2.645 US. gals) of oil. Consequently,
when undertaking a transmission replacement,
oil replenishment should not be necessary. The
exterior of the transmission is coated with a non-
drip corrosion protection oil, which must not be
95.8 kg (211 lbs)
ATF Esso LT71141
10 liters (2.645 US. gals)
1st Gear
3.571:1
2nd Gear 2.202:1
3rd Gear
4th Gear
5th Gear
Reverse
1.505:1
1.000:1
0.803:1
4.095:1
Gearshifting
Driver gear selection is transmitted from the gear
selector lever by cable to a lever fitted to a
selector shaft in the transmission casing. This
shaft moves the manual valve and the rotary
switch. The rotary switch signals all gear
positions except D to 4. A separate switch in the
driver gear selector mechanism detects
movement of the selector between D and 4. The
communication of driver gear selection to the
TCM is made by the rotary switch. Gear shift
points are selected by the TCM in response to
output speed, engine load, selector position,
accelerator pedal position and driver mode
selection. Driver control of the shifting is via the
selector lever, throttle pedal position, kickdown
switch and mode switch. Two shift modes are
available, sport and normal, controlled by the
driver from a switch on the gear selector
surround. During kickdown, gear upshifts occur at
6800 RPM engine speed.
Mechanical Description
The unit is an oil filled-for-life system therefore no
dipstick is fitted to the transmission. A filling/level
plug is located at the right-hand side rear of the
casing for service oil level checking and
replenishment, if required. To achieve effective
cooling, the oil is pumped from the transmission
casing at the front left-hand side of the casing to
the car mounted oil cooler. The oil is returned
from the cooler to the inlet connection on the
front right-hand side of the casing. The cooler is a
plate-type design made from aluminum and is
located in the car radiator outlet tank. To detect
changes in oil viscosity which occur as the oil
temperature changes, an oil temperature sensor
is located in the unit casing sump. Also located
66
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24
Transmission
Electrical Description
mistaken for an oil leak.
BAYONET CONNECTOR
Electrical Connections
Bayonet Connector
A round, 16-pin, bayonet electrical connector is
fitted at the rear left-hand side of the
transmission which communicates with the 5
pressure regulators, 3 shift solenoids, oil
temperature sensor and the input and output
1
3
2
5
9
6
13
16
10
14
EM 046
307-023
Connector/
Pin
Circuit
Pin
Circuit
Pin
Circuit
shaft speed sensors.
EM046
006 Turbine Speed Sensor (-)
007 Pressure Regulator 3
008 Shift Solenoid 1
009 Shift Solenoid 2
010 Output Speed Sensor (-)
011 Pressure Regulator 4
012 Solenoid Valves (+)
013 Analog Ground
014 Oil Temperature Sensor
015 Pressure Regulator 5
016 Regulator (+)
001 Output Speed Sensor (+)
002 Pressure Regulator 1
003 Pressure Regulator 2
004 Shift Solenoid Valve 3
005 Turbine Speed Sensor (+)
Rotary Switch Connector
ROTARY SWITCH CONNECTOR
The rotary switch, mounted on the right-hand
side of the casing, has a spline arrangement
which prevents misalignment with the selector
shaft. A locating pin and two bolts secure the
rotary switch to the transmission casing. This
locates the switch with the transmission casing
and the shaft in one place only. The switch
requires no other setting up procedure.
H
F G
J K
A 10-way connector with flying lead connects the
rotary switch to the engine management
harness. The connector is retained on a multi-
connector bracket bolted to the transmission
casing/torque converter housing joint.
E
D
C
B
A
EM 047
307-024
Connector/
Pin
Circuit
Pin
Circuit
Pin
Circuit
EMO47
00A Position L1
00B Position L2
00C Position L3
00D Position L4
00E Digital Ground
00F Not Used
00G Not Used
00H Not Used
00J
12V Power Supply
00K Park & Neutral Switch
67
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24
Transmission Management
Transmission Management
The transmission management system uses both
analogue and digital signals, to control the
operation of the transmission. Digital signals are
processed by the TCM to and from the vehicle
multiplex network. Other input/output analogue
signals are hardwired to the TCM. This
information is used primarily by the TCM to
decide which shift program to implement, which
gear to select and for shift energy management.
If a fault occurs, the TCM will take default action
and inform the driver via the Message Centre and
amber warning light.
TCM
Harness Connector
The vehicle harness connector for the TCM is an
88-way latching connector. The TCM is wired to
the electrical pressure regulators/solenoids, oil
temperature sensor and shaft speed sensors in
the transmission casing.
303-009
Sport Mode
When sport mode is selected by the driver using
the mode switch, the sport pattern is only
activated when a set cornering force is achieved,
or the kickdown switch is pressed. The vehicle
speed and the difference in speeds between the
two front wheels is used to calculate the amount
of cornering force.
Torque Convertor Lock-up
The torque convertor lock-up clutch is engaged
as a function of throttle position, output speed,
oil temperature, gear shift and shift program.
Lockup is possible in 2nd, 3rd, 4th and 5th gears
but is usually restricted to 4th and 5th gears.
During a gear shift the TCM controls the amount
of slip of the lock-up clutch to enhance shift
quality.
Oil Temperature
When the engine coolant or transmission oil
temperature exceeds set thresholds a hot mode
program is selected which locks the torque
convertor clutch, minimising the amount of heat
entering the engine cooling system from the
transmission oil.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24
Transmission Management
Gear Shift Interlock
Fault Monitoring/Diagnostics
Gear shift interlock is controlled by the BPM, part
of the SCP network. The gearshift release will
only be activated when the ignition is in position
II, transmission is in Park and the brake pedal is
depressed. Once transmission is out of Park, the
brake pedal has no effect on gearshifting and the
interlock is disabled.
The TCM constantly monitors the transmission
system for faults. In the event of a fault
occurring, the transmission is protected by a limp
home mode. This mode allows use of P, R, N,
and 4. It also signals the ECM to switch on the
CHECK ENG (MIL) lamp.
The TCM is able to diagnose faults in
components which affect exhaust emissions.
Communication with the PDU is through the
J1962 connector which allows accurate diagnosis
of transmission problems. Additional diagnostic
functions facilitate fast repair of faults. All
transmission OBDII information is stored for
future data analysis in the ECM.
Reverse Inhibit
Selection of reverse with the vehicle moving
forwards above walking pace is electrically
inhibited, unless the vehicle is in the default
"limp-home" mode.
Kickdown
A floor mounted switch/pedal position sensor
signals the TCM to select the lowest gear to give
maximum torque for acceleration.
Torque Control
The TCM synchronises the operation of the
transmission clutches and invokes shift energy
management to control engine output torque
during a gear shift (Refer to EMS, page 60).
Traction Mode
The traction program compliments the traction
control system and is implemented whenever
traction control intervenes to maximize wheel
stability.
Cruise Mode
Cruise mode reduces unwanted hunting of the
transmission gearshifting and is activated when
cruise control is resumed and when the vehicle is
cruising near the set speed.
Gradient Mode
The gradient program enhances vehicle
performance, driveability and cooling when the
vehicle is climbing a gradient.
Start Inhibit
The rotary switch also provides the start inhibit
function to the ECM, which will not allow an
engine start until the gear selector is in either
Park or Neutral.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24
Transmission Management
TCM
28
55
88
1
29
56
EM 007
307-022
Transmission Control Module Pin Connections
Connector/
Pin
Circuit
Pin
Circuit
Pin
Circuit
EM007
045 Mode Switch Pin A
046
047 Not used
001 Pressure Regulator 2
002 Mode Switch Illumination
003 Not used
023 Shield (Input Speed Sensor)
024 Not used
025 Not used
)
048
049
050
)
)
)
004 Pressure Regulator 4
005 Pressure Regulator 1
006 Power Ground
007 Not used
008 Position Switch L2
009 Position Switch L4
010 Not used
026 Battery Feed
027 Not used
028 Digital Ground
029 Pressure Regulator 3
030 Shift Solenoid 1
031 Not used
032 Shift Solenoid 3
033 Shift Solenoid 2
034 Power Ground
035 Not used
036 Position Switch L1
037 Position Switch L3
051 Pressure Regulator 5
052 Solenoid valve + ve
053 Pressure regulator + ve
054 Fused Ignition + ve
055 Fused Ignition + ve
056
011 Not used
012 Mode Switch Pin B
013 Drive to Fourth Switch
014 Turbine Speed (-)
015 Shield (Output Speed Sensor)
016 Output Speed (+)
017 Not used
018 Kickdown Switch
019 Not used
020 Not used
to
081 Not used
082 CAN Link In - ve
083 CAN Link In + ve
084 CAN Link Screen
085 CAN Link Out - ve
086 CAN Link Out + ve
087 Not used
038
)
039 Not used
040
041
)
)
042 Turbine Speed (+)
043 Not used
044 Output Speed (-)
088 Not used
021 Analogue Ground
022 Oil Temp Sensor
70
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24
Transmission Management
Can Messages
Messages on the CAN data bus used or output by the TCM are detailed below:
Note: This list does not include network monitoring or diagnostic related messages.
Message Used by TCM
Source/Used by
Message Produced by TCM
TRACTION STATUS
ABS STATUS
FRONT LEFT WHEEL SPEED
FRONT RIGHT WHEEL SPEED
Brake Control Module
TRANSMISSION INPUT SPEED
TRANSMISSION OUTPUT SPEED
TORQUE CONVERTER SLIP
KICKDOWN SWITCH
GEAR POSITION ACTUAL
TORQUE CONVERTER STATUS
TRANSMISSION SHIFT MAP
TRANSMISSION MALFUNCTION
TRANSMISSION FAULT CODES
Instrument Cluster
GEAR POSITION ACTUAL
GEAR POSITION SELECTED
TRANSMISSION OIL TEMPERATURE
TRANSMISSION MALFUNCTION
ESTIMATED ENGINE TORQUE
THROTTLE VALVE POSITION
ACCELERATOR PEDAL POSITION
TORQUE REDUCTION
ACKNOWLEDGE
ENGINE SPEED
ECM
TORQUE REDUCTION REQUEST
TRANSMISSION OVERLOAD
TRANSMISSION INPUT SPEED
TRANSMISSION OUTPUT SPEED
TORQUE CONVERTER SLIP
KICKDOWN SWITCH
CRUISE STATUS
GEAR POSITION ACTUAL
BRAKE PEDAL DEPRESSED
ENGINE COOLANT TEMPERATURE
ENGINE MALFUNCTION
TORQUE CONVERTER STATUS
GEAR POSITION SELECTED
TRANSMISSION SHIFT MAP
TRANSMISSION OIL TEMPERATURE
TRANSMISSION MALFUNCTION
TRANSMISSION FAULT CODES
71
Download from Www.Somanuals.com. All Manuals Search And Download.
AJ-V8/5HP24
Service Tools
New Tools
The table below lists the new service tools required for the AJ V8 engine. These are in addition to the
tools already in use on 6 and 12 cylinder engines, some of which can also be used on the AJ V8.
Details of new service tools for the 5HP24 transmission will be supplied at a later date.
Part Number
Description
JD 215
JD 216
JD 217
JD 218
JD 220
JD 221
JD 222
JD 223
JD 229
JD 230
JD 231
JD 232
JD 233
JD 234
JD 235
MS 76-140-5
Camshaft setting/locking tool
Crankshaft setting/locking peg
Timing chain tensioner tool
Timing chain wedges (2 each)
Dummy main bearing caps (5 each)
Bore protector - connecting rod installation (2 each)
Engine rear lifting brackets (1 pair)
Engine stand mounting brackets (1 pair)
Crankshaft rear oil seal remover/replacer
Belt tensioner release tool
Fuel injector remover
Valve lifter hold-down tool
Fan nozzle air gun
Crankshaft front oil seal remover
Crankshaft front oil seal replacer
Valve seat 5 mm pilot (for use with existing MS 76 valve seat cutter tools)
18G 1437-2
-
Adapter (for use with existing front pulley lock tool 18G 1437)
Cranked 13 mm box wrench, for starter motor upper securing bolt (eg. Snap-on part
number CXM 1113)
-
-
-
-
Spring band hose clamp pliers (eg. Snap-on part number HCP 20)
Torque/Angle disc, for yield tightening of bolts (eg. Snap-on part number TA 360)
Valve seal pliers (eg. Snap-on part number YA 8230)
24 mm, 0.375 inch drive, open wrench, for knock sensors (eg. Snap-on part number
FCOM 24)
-
8 inch long, 0.375inch drive, angle extension, for use with 24 mm open wrench
(eg. Snap-on part number FXW 8)
72
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Indesit Convection Oven BIM 51 KA IX GB User Manual
Invacare Mobility Aid 1335 User Manual
Jade Range Oven JTKC 24 User Manual
JBL Car Speaker P6462 User Manual
Jensen Car Stereo System CD510K User Manual
Johnson Hardware Door Series 2200F User Manual
Kenwood Speaker KFC P722 User Manual
Knoll Systems Stereo Amplifier GSZ44 User Manual
Kodak Camera Lens GE1900 User Manual
Krell Industries Speaker LAT 1 User Manual