VIDEO CASSETTE RECORDER
SR-V10U
CABLE/ MBRSET
TV
DBS
A/B
POWER
TV/VCR A. MONITOR DISPLAY
1
2
3
2
4
5
6
DBS
DAILY
WEEKLY
7
C.RESET
8
9
AUX
CANCEL
TIMER
4
0
START
STOP
DATE
CH
EXPRESS PROGRAMMING
PROG
PROG
CHECK
SP/EP
SKIP SEARCH
1
PLAY
STOP
FF
REW
PLAY
POWER
–
+
C
CH– /+
PUSH TURN
/
SHUTTLE
PLUS
REC LINK
A.DUB
S
VIDEO
VIDEO (MONO)L—AUDIO—R
24HR QUICK
PROGRAM
SP EP
VCR
DIGITAL TBC/NR
INSERT
REC
PAUSE
STOP/EJECT
MULTI BRAND
REMOTE CONTROL UNIT
For Customer Use:
Enter below the Model No. and
Serial No. which are located on the
rear of cabinet. Retain this
INSTRUCTIONS
information for future reference.
Model No.
Serial No.
LPT0604-001A
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
3
5. Ventilation
IMPORTANT PRODUCT
SAFETY INSTRUCTIONS
Electrical energy can perform many useful functions. But
improper use can result in potential electrical shock or fire
hazards. This product has been engineered and manufactured
to assure your personal safety. In order not to defeat the built-in
safeguards, observe the following basic rules for its installation,
use and servicing.
Slots and openings in the cabinet are provided for ventilation.
To ensure reliable operation of the product and to protect it
from overheating, these openings must not be blocked or
covered.
• Do not block the openings by placing the product on a bed,
sofa, rug or other similar surface.
• Do not place the product in a built-in installation such as a
bookcase or rack unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
6. Wall or Ceiling Mounting
The product should be mounted to a wall or ceiling only as
recommended by the manufacturer.
ATTENTION:
Follow and obey all warnings and instructions marked on your
product and its operating instructions. For your safety, please
read all the safety and operating instructions before you operate
this product and keep this booklet for future reference.
ANTENNA INSTALLATION
INSTRUCTIONS
1. Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the
product, be sure the antenna or cable system is grounded so as
to provide some protection against voltage surges and built-up
static charges. Article 810 of the National Electrical Code,
ANSI/NFPA 70, provides information with regard to proper
grounding of the mast and supporting structure, grounding of
the lead-in wire to an antenna discharge unit, size of grounding
connectors, location of antenna discharge unit, connection to
grounding electrodes, and requirements for the grounding
electrode.
INSTALLATION
1. Grounding or Polarization
(A) Your product may be equipped with a polarized alternating-
current line plug (a plug having one blade wider than the
other). This plug will fit into the power outlet only one way.
This is a safety feature.
If you are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the polarized plug.
(B) Your product may be equipped with a 3-wire grounding-type
plug, a plug having a third (grounding) pin. This plug will
only fit into a grounding-type power outlet. This is a safety
feature.
2. Lightning
For added protection for this product during a lightning storm,
or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet and disconnect the antenna
or cable system. This will prevent damage to the product due to
lightning and power-line surges.
If you are unable to insert the plug into the outlet, contact
your electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the grounding-type plug.
3. Power Lines
2. Power Sources
An outside antenna system should not be located in the vicinity
of overhead power lines or other electric light or power circuits,
or where it can fall into such power lines or circuits. When
installing an outside antenna system, extreme care should be
taken to keep from touching such power lines or circuits as
contact with them might be fatal.
Operate your product only from the type of power source
indicated on the marking label. If you are not sure of the type of
power supply to your home, consult your product dealer or
local power company. If your product is intended to operate
from battery power, or other sources, refer to the operating
instructions.
3. Overloading
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or
electric shock.
ANTENNA
LEAD IN WIRE
4. Power Cord Protection
Power supply cords should be routed so that they are not likely
to be walked on or pinched by items placed upon or against
them, paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the product.
GROUND CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION
810-20)
ELECTRIC SERVICE
EQUIPMENT
GROUNDING
CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING ELECTRODE SYSTEM
(NEC ART 250. PART H)
NEC – NATIONAL ELECTRICAL CODE
Download from Www.Somanuals.com. All Manuals Search And Download.
4
EN
USE
SERVICING
1. Accessories
1. Servicing
To avoid personal injury:
If your product is not operating correctly or exhibits a marked
change in performance and you are unable to restore normal
operation by following the detailed procedure in its operating
instructions, do not attempt to service it yourself as opening or
removing covers may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
• Do not place this product on an unstable cart, stand, tripod,
bracket, or table. It may fall, causing serious injury to a child
or adult, and serious damage to the product.
• Use only with a cart, stand, tripod, bracket, or table
recommended by the manufacturer or sold with the product.
• Use a mounting accessory recommended by the
manufacturer and follow the manufacturer’s instructions for
any mounting of the product.
2. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
a.When the power supply cord or plug is damaged.
b.If liquid has been spilled, or objects have fallen into the
product.
• Do not try to roll a cart with small casters across thresholds or
deep-pile carpets.
2. Product and Cart Combination
A product and cart combination should
c.If the product has been exposed to rain or water.
d.If the product does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as an improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the product to its normal operation.
PORTABLE CART WARNING
(Symbol provided by RETAC)
be moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the product and cart
combination to overturn.
e.If the product has been dropped or damaged in any way.
f. When the product exhibits a distinct change in
performance—this indicates a need for service.
3. Replacement Parts
3. Water and Moisture
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer or which have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock or other hazards.
Do not use this product near water—for example, near a bath
tub, wash bowl, kitchen sink or laundry tub, in a wet basement,
or near a swimming pool and the like.
4. Object and Liquid Entry
Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or short-
out parts that could result in a fire or electric shock. Never spill
liquid of any kind on the product.
4. Safety Check
Upon completion of any service or repairs to this product, ask
the service technician to perform safety checks to determine
that the product is in safe operating condition.
5. Attachments
Do not use attachments not recommended by the manufacturer
of this product as they may cause hazards.
HOW TO USE THIS INSTRUCTION
MANUAL
6. Cleaning
● The Index on pages 58 – 62 lists frequently-used terms, and
the number of the page on which they are used or explained
in the manual. This section also illustrates the controls and
connections on the front and rear panel, the front display
panel and the Remote.
Unplug this product from the wall outlet before cleaning. Do
not use liquid cleaners or aerosol cleaners. Use a damp cloth
for cleaning.
● The ੬ mark signals a reference to another page for
instructions or related information.
● Operation buttons necessary for the various procedures are
clearly indicated through the use of illustrations at the
beginning of each major section.
7. Heat
The product should be situated away from heat sources such as
radiators, heat registers, stoves, or other products (including
amplifiers) that produce heat.
BEFORE YOU INSTALL YOUR NEW
VCR . . .
. . . please read the sections/literature listed below.
● ”CAUTIONS” on page 2
● ”IMPORTANT PRODUCT SAFETY INSTRUCTIONS” on the
previous page
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
EN
5
INSTALLING YOUR NEW VCR
6
SPECIAL EFFECT PLAYBACK
26
Basic Connections ..................................6
Special Effect Playback ........................26
Locating particular scene rapidly
— Picture Search .....................................................26
Viewing still picture — Still Picture Playback ...........27
Skipping unwanted portions — Skip Search .............27
Viewing still picture frame by frame
— Frame-by-Frame Playback...................................27
Viewing slow motion picture
— Slow Motion Playback ........................................27
INITIAL SETTINGS
8
Plug & Play Setting ................................8
Auto Clock Set/Auto Tuner Set ...................................8
Clock Setting........................................10
Preparations.............................................................10
Setting clock semiautomatically
— Semiauto Clock Set ............................................. 11
Setting clock manually
— Manual Clock Set................................................12
TIMER RECORDING
28
VCR Plus+® Timer Programing ..............28
Changing VCR Plus+® Setting................30
Express Timer Programing ...................32
24HR Quick Programing ......................34
Checking program settings .......................................35
Canceling or changing program settings ..................35
When programs overlap each other .........................36
Tuner Setting .......................................13
Setting channels automatically
— Auto Channel Set ................................................13
Setting channels manually
— Manual Channel Set ............................................14
BASIC PLAYBACK AND RECORDING
15
Basic Playback ....................................15
To stop playback ......................................................15
To rewind the tape ...................................................15
To fast-forward the tape ...........................................15
To eject the tape ......................................................15
To turn off the VCR ..................................................15
OTHER USEFUL FUNCTIONS
37
Useful Function Settings .......................37
Satellite Auto Recording.......................42
Child Lock ............................................43
Basic Playback Features ......................16
Changing display information ..................................16
Checking tape position ............................................16
Playing back tape repeatedly — Repeat Play ...........16
Adjusting tracking condition
EDITING
44
Edit From Camcorder ...........................44
Edit To Or From Another VCR ...............46
Audio Dubbing ....................................47
Insert Editing and AV Dubbing .............48
— Tracking Adjustments ..........................................17
Selecting monitor sound — Audio Monitor ..............17
Automatic operations after rewinding
— Next Function Memory .......................................17
Locating beginning of recordings
MULTI-BRAND REMOTE CONTROL
50
— Index Search .......................................................17
Locating beginning of timer recordings
TV Brand Setting..................................50
Cable Box Brand Setting ......................51
DBS Receiver Brand Setting ..................52
Changing Remote Control Code............53
— Instant Review.....................................................18
Adjusting picture condition
— Digital TBC/NR ...................................................18
Basic Recording ...................................19
To pause recording ..................................................19
To stop recording .....................................................19
To rewind the tape (when it is not running) ..............19
To fast-forward the tape (when it is not running) ......19
To eject the tape ......................................................19
To turn off the VCR ..................................................19
Basic Recording Features .....................20
Changing display information ..................................20
Recording on one tape repeatedly
TROUBLESHOOTING
Questions and answers ............................................57
54
INDEX
58
List of terms .............................................................58
Front panel ..............................................................59
Front display panel ..................................................60
Rear panel ...............................................................61
On-screen display....................................................61
Remote ....................................................................62
— Repeat Recording...............................................20
Watching one program while recording another ......20
Showing on-screen display ......................................21
SPECIFICATIONS
63
SERIES PLAYBACK AND RECORDING
22
Series Playback ...................................22
Series Recording ..................................24
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING YOUR NEW VCR
6
EN
Basic Connections
ANTENNA IN
(Antenna or cable input)
Antenna or cable
Coaxial cable
Flat feeder
Matching transformer
(Not supplied)
AUDIO OUT
VIDEO OUT
AC Power
Cord
REMOTE
IN
IN
OUT
ANTENNA IN
R
L
REMOTE
OUT
AUDIO
VIDEO
IN
OUT
VHF/UHF
TV OUT
S
V
I
D
E
O
Back of VCR
S VIDEO OUT
TV OUT
AC Outlet
S-video cable
(Supplied)
To S-video input
connector
Audio/video cable
(Supplied)
To Audio/video input
connectors
RF cable (Supplied)
To 75 ohm terminal
TV
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
7
Check contents
Make sure the package contains all of the
accessories listed in “SPECIFICATIONS”
(੬ pg. 63).
Connect VCR to power source
1
4
5
Connect the AC power plug to an AC outlet.
● The clock and tuner channels will
automatically be set when the antenna is
connected and when the AC power cord is first
connected to an AC power outlet (੬ pg. 8).
(If “Auto” or “CH” is displayed on the front display
panel before the VCR is turned on, the clock and
tuner channels are being set automatically. Wait
until the clock time is displayed on the front display
panel before turning on the VCR.)
Situate VCR
Place the VCR on a stable, horizontal surface.
2
3
Connect VCR to TV
The following connections are required.
RF Connection
1 Disconnect the TV antenna from the TV.
2 Connect the TV antenna cable to the
ANTENNA IN terminal on the rear of the VCR.
3 Connect the supplied RF cable between the TV
OUT terminal on the rear of the VCR and the
TV’s antenna input terminal.
Set VCR channel
Press POWER to turn off the VCR and press STOP/
EJECT ( § ) on the front panel for more than
5 seconds. “3CH” appears on the display panel.
Press CH + and – on the Remote to select “3CH” or
“4CH” for only RF connection, “–CH” (OFF) for RF
and AV connection, then press OK.
AV Connection (improves picture quality during
tape playback.)
● The VCR channel is preset to 3CH.
Set to 4CH if 3CH is used for broadcasting in your
area. (To view the picture from this VCR through
this channel, select the same channel on the TV
with the VCR channel setting on the VCR.)
● You can now perform basic playback
If your TV is equipped with audio/video input
connectors
1 Connect the antenna, VCR and TV as shown in
the illustration.
2 Connect an audio/video cable between the
AUDIO/VIDEO OUT connectors on the rear of
the VCR and the audio/video input connectors
on the TV.
(੬ pg. 15) or basic recording (੬ pg. 19).
NOTES:
● The VCR channel is the channel on which you can watch the
picture from the VCR on the TV when only using the RF
connection.
S-video Connection (allows you to make the
most of the S-VHS picture performance.)
If your TV is equipped with an S-video input
connector
1 Perform “RF Connection” and RED/WHITE
AUDIO connections.
● Even if you are using audio/video cables to connect your VCR
to your TV, you must also connect it using the RF cable. This
will ensure that you can record one show while watching
another (੬ pg. 21).
2 Connect an S-video cable between the S VIDEO
OUT connector on the rear of the VCR and the
S-video input connector on the TV.
● For full identification of the VCR’s rear panel, refer to the
Index ( ੬ pg. 61).
Installing/Removing the lithium battery
Be sure to connect the power plug to an AC outlet first
before installing the lithium battery; otherwise, the
battery's service life will be drastically shortened.
1 Make sure that the power plug is connected to an AC outlet
and turn off the VCR power.
2 Open the battery cover while pressing the release tab as
illustrated.
3 Insert a lithium battery with the plus (+) side up and push it in.
● To remove the lithium battery, press the latch A down-
ward using a pointed non-metallic object, then pull out
the lithium battery.
REMOTE
IN
OUT
IN
ANTENNA IN
R
L
REMOTE
OUT
AUDIO
VIDEO
IN
OUT
VHF/UHF
TV OUT
S
V
I
D
E
O
4 Close the battery cover until it clicks in place.
A
Download from Www.Somanuals.com. All Manuals Search And Download.
INITIAL SETTINGS
8
EN
This VCR sets the clock and tuner channels
automatically when AC power cord is first connected to
an AC outlet. The antenna cable must be connected for
the Plug & Play setting.
The time and date can be set automatically by the clock
setting data transmitted from one of the regular TV
broadcast channels. We call this TV channel the “host
channel” and it is a PBS channel in your area.
Plug & Play
Setting
Auto Clock Set/Auto Tuner Set
Perform Plug & Play setup
1
Connect the antenna cable to the VCR (੬ pg.
ATTENTION
6). Then connect the AC power cord to an AC
outlet. Do not turn on the VCR.
The clock and tuner channels will be set
automatically.
● If you use a cable box, Plug & Play will not function; set
the clock and tuner channels separately. (੬ pg.10 – 14)
● It takes several minutes for the VCR to complete the Plug
& Play setting.
● Do not press any buttons on the front panel or on the
Remote while Plug & Play is in progress.
NOTES:
● Auto Clock Set is performed first.
“Auto” blinks on the front display panel during Auto
Clock Set.
● Auto Channel Set is performed next. Auto Channel
Set scans all the channels that are receivable by your
VCR. During Auto Channel Set, the channel numbers
are displayed as they are scanned and set.
REW
FF
PLAY
POWER
–
+
● When Plug & Play setting has been complete
successfully, the correct clock time is displayed. If you
perform Plug & Play setting successfully, there is no
need to perform the clock (੬ pg. 10) and tuner (੬ pg.
13) settings. If, however, you want to add or delete
channels, refer to Manual Channel Set on page 14.
CH– /+
PUSH TURN
/
REC LINK
A.DUB
S
VIDEO (MONO)L—AUDIO—R
24HR QUICK
PROGRAM
SP EP
VCR
DIGITAL TBC/NR
INSERT
REC
PAUSE
STOP/EJECT
During Initial Auto Clock Set
“Auto” blinks.
During Auto Channel Set
The channel numbers are displayed
as they are scanned and set.
Plug & Play Completed
The current time (including
AM/PM) is displayed.
* If an incorrect clock time or “– –:– –” appears on the display panel, see “What to do if Plug & Play setting failed”
below.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
9
INFORMATION
● If “AUTO CLOCK” is set to “ON” on the Clock Set screen on page 11, the clock will be adjusted automatically by the host
channel every hour (except 11:00 PM, midnight, 1:00 AM and 2:00 AM) using the incoming PBS channel clock setting data.
(This automatic clock adjustment can only be performed when the VCR is turned off. The clock will be adjusted just on these
hours — on the time displayed on the front display panel, not on the actual real time.)
The default setting of “AUTO CLOCK” is “ON”.
● If the memory backup fails, because a power outage occurs or because the AC power cord is unplugged, Plug & Play will be
performed when power is restored to the VCR.
● Poor antenna or cable signal may prevent the VCR from receiving the Auto clock setting data from the PBS channel. If this
function is taking a considerable amount of time, it may be necessary to perform the Semiauto or Manual Clock Set
procedure.
What to do if Plug & Play setting failed
● If an incorrect time is displayed on the front display panel, you may be receiving the clock setting data of a PBS channel from
an adjacent time zone, or an incorrect PBS channel from a cable TV system. In this case, perform the Semiauto (੬ pg. 11) or
Manual Clock Set (੬ pg. 12) procedure.
● If “- -:- -” appears on the front display panel, your antenna cable may not be connected to the VCR or there may not be a Host
PBS signal available in your area. Ensure that the antenna cable is connected correctly. Then turn on and off the VCR; the Plug
& Play setting will be automatically reactivated.
If Plug & Play setting is not performed though the antenna cable is connected correctly, perform Manual Clock Set (੬ pg. 12)
and Auto Channel Set or Manual Channel Set (੬ pg. 13 or 14).
Last-Function Memory
When the AC is removed from the VCR or when the power failure occurs, your settings for the following functions
are kept in memory. These settings will resume when the VCR is turned on again.
a- Input Selection (channel or auxiliary input; L-1 or F-1)
b- Recording tape speed (੬ pg. 19)
c- “ON SCREEN (REC)” (੬ pg. 37, 38)
d- “ON SCREEN (PLAY)” (੬ pg. 37, 39)
e- “RETURN POINT” (੬ pg. 37, 41)
f- “DAY/TIME INSERT” (੬ pg. 37, 41)
g- “REC SAFETY” (੬ pg. 37, 41)
Download from Www.Somanuals.com. All Manuals Search And Download.
INITIAL SETTINGS (cont.)
10
EN
Perform clock setting only if the clock has not been set
correctly by the Plug & Play setting or if you use a cable
box.
Access the Clock Set screen to perform the Semiauto or
Manual Clock Set. Each procedure starts from step 4
after preparation steps below are finished.
If you use a cable box, set the clock manually. (੬ pg. 12)
Clock Setting
Turn on the VCR and the TV, and select the VCR
channel 3 or 4 (or AV mode) on the TV.
Preparations
Access Main Menu screen
1
2
Press MENU.
Access Initial Set screen
Press SHUTTLE PLUS
1
4
7
2
5
8
3
6
9
MAIN MENU
2
%fi to move the
FUNCTION SET
highlight bar (arrow) to
= TUNER SET
INITIAL SET
“INITIAL SET”, then
press OK or SHUTTLE
4
0
PLUS
#.
PRESS (5,∞), THEN (OK)
PRESS (MENU) TO END
Select clock set
3
1
Press SHUTTLE PLUS
%fi to move the
INITIAL SET
=
CLOCK SET
GUIDE CHANNEL SET
highlight bar (arrow) to
“CLOCK SET”, then
press OK or SHUTTLE
PLUS
#.
SELECT WITH (5,∞) AND (OK)
2 –7
1 8
PRESS (MENU) TO END
2 –7
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
11
Setting clock semiautomatically
Select D.S.T. mode
6
7
You have three choices:
— Semiauto Clock Set
AUTO– Select if you want to adjust your VCR’s
clock automatically by the incoming
signal from the host channel. (Auto
Daylight Saving Time*)
You can change the host channel/D.S.T. /time zone
setting manually.
First follow steps 1 to 3 on page 10, then go to the
following steps.
ON–
Adjustment will be made by the built-in
clock itself.
Set Auto Clock to ON
OFF–
Select when Daylight Saving Time does
not apply to you.
4
Press SHUTTLE PLUS
#
CLOCK SET
DATE YEAR
to move the highlight
TIME
Press SHUTTLE PLUS
to “D.S.T.”, then press SHUTTLE PLUS %fi
repeatedly until the desired setting is selected.
#
to move the highlight bar
1:00PM 12/24 02 TUE
AUTO CLOCK : ON
bar to “AUTO CLOCK”,
then press SHUTTLE
PLUS %fi so that “ON”
is selected.
HOST CH
D.S.T.
: AUTO (CATV)
: AUTO
TIME ZONE : AUTO
PRESS (5,∞), THEN (OK)
Select time zone
You can select the time zone automatically or
manually.
PRESS (MENU) TO END
Then;
To select the host
channel — go to step 5.
To select the D.S.T. mode — go to step 6.
To select the time zone — go to step 7.
Press SHUTTLE PLUS
#
to move the highlight bar
to “TIME ZONE”, press SHUTTLE PLUS %fi
repeatedly until “AUTO” or the desired time zone
is selected.
NOTE:
Each time you press the button, the time zone
changes as follows:
The time set previously will be erased when “AUTO
CLOCK”, “HOST CH”, “D.S.T.” or “TIME ZONE”
setting is changed.
= AUTO = ATLANTIC = EASTERN
= CENTRAL = MOUNTAIN = PACIFIC
= ALASKA = HAWAII = (back to the beginning)
Select host channel
5
You can either select “AUTO” or enter a PBS
channel number.
NOTE:
Press SHUTTLE PLUS
#
to move the highlight bar
If an incorrect clock time is displayed by the Plug &
Play setting, you may be receiving the clock setting
data of a PBS channel from an adjacent time zone or
from an incorrect PBS channel from a cable TV system.
If you selected "AUTO" for the host channel in step 5,
be sure to select the correct time zone manually.
to “HOST CH”, then press SHUTTLE PLUS %fi
until “AUTO” or the desired PBS channel number
is selected.
NOTE:
Some PBS channels do not transmit clock setting data.
Return to normal screen
Press MENU.
8
* Auto Daylight Saving Time
This function enables automatic adjustment of the VCR’s
clock at the start and end of Daylight Saving Time.
With Auto DST activated, . . .
IMPORTANT
. . .
on the first Sunday of April at 2:00 AM, the clock is
Turn off the VCR after performing Semiauto Clock Set.
”Auto” will appear on the front display panel while the
clock is being set. The current clock time will appear
automatically when the clock setting is complete.
adjusted to 3:00 AM.
. . .
on the last Sunday of October at 2:00 AM, the
clock is adjusted to 1:00 AM.
Download from Www.Somanuals.com. All Manuals Search And Download.
INITIAL SETTINGS (cont.)
12
EN
Set date
5
Press SHUTTLE PLUS %fi until the desired date
appears, then press OK or SHUTTLE PLUS
#
.
● Holding SHUTTLE PLUS %fi changes the date
in 15-day intervals.
1
4
7
2
5
8
3
6
9
Set year
2
6
7
Press SHUTTLE PLUS %fi until the desired year
appears, then press OK or SHUTTLE PLUS
#
twice.
Select D.S.T. mode
You can select either “ON” or “OFF”.
ON– Adjustment will be made by the built-in
clock itself.
4
0
OFF– Select when Daylight Saving Time does
not apply to you.
1
Press SHUTTLE PLUS %fi to select the desired
setting.
Start clock
8
Press MENU and normal screen appears.
8
4 –7
To make corrections any time during the process
Press OK or SHUTTLE PLUS
you want to change blinks, then press SHUTTLE PLUS
#
repeatedly until the item
%fi.
4 –7
Setting clock manually
— Manual Clock Set
First follow steps 1 to 3 on page 10, then go to the
following steps.
Set time
4
Press SHUTTLE PLUS
CLOCK SET
%fi until the desired
time appears, then press
TIME
DATE YEAR
– –:– –AM 1/ 1 02
AUTO CLOCK : ON
OK or SHUTTLE PLUS
HOST CH
D.S.T.
: AUTO (CATV)
: AUTO
#
.
TIME ZONE : AUTO
PRESS (5,∞), THEN (OK)
PRESS (MENU) TO END
● Holding SHUTTLE PLUS %fi changes the time
in 30-minute intervals.
● When the time is entered manually, “AUTO
CLOCK” is automatically set to “OFF”, and
“HOST CH” and “TIME ZONE” disappear.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
13
Setting channels
Tuner Setting
Turn on the VCR and the TV, and select the VCR
channel 3 or 4 (or AV mode) on the TV.
automatically — Auto Channel Set
Use Auto Channel Set only if channels have not been set
correctly by the Plug & Play setting. If you want to add
or delete channels, use Manual Channel Set (੬ pg. 14).
Access Main Menu screen
1
2
Press MENU.
Access Tuner Set screen
Press SHUTTLE PLUS
MAIN MENU
%fi to move the
= FUNCTION SET
TUNER SET
highlight bar (arrow) to
INITIAL SET
“TUNER SET”, then
1
4
7
2
5
8
3
6
9
2
press OK or SHUTTLE
PLUS
#.
PRESS (5,∞), THEN (OK)
PRESS (MENU) TO END
4
0
Perform Auto Channel Set
3
4
You can automatically
set the receivable
TUNER SET
= BAND
CATV
channels in your area in
the order of their
AUTO CHANNEL SET
MANUAL CHANNEL SET
1
frequencies.
Press SHUTTLE PLUS
%fi to move the
highlight bar (arrow) to
“AUTO CHANNEL
SET”, then press OK or
SELECT WITH (5,∞) AND (OK)
PRESS (MENU) TO END
AUTO CHANNEL SET
SCANNING...
1 4
2 3
2 3
SHUTTLE PLUS
#.
PRESS (MENU) TO END
NOTES:
● When Auto Channel Set is complete, “SCAN
COMPLETED” appears on screen.
● If the scan was unsuccessful, “SCAN COMPLETED–
NO SIGNAL” appears on screen. Check the
connections and start again.
Return to normal screen
Press MENU.
INFORMATION
The VCR selects the correct band (TV or CATV)
automatically during Auto Channel Set.
The selected band will be displayed on the right side of
“BAND” on the Tuner Set screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
INITIAL SETTINGS (cont.)
14
EN
Access Tuner Set screen
2
3
Press SHUTTLE PLUS %fi to move the highlight
bar (arrow) to “TUNER SET”, then press OK or
SHUTTLE PLUS
#.
Access Manual Channel Set screen
Press SHUTTLE PLUS
TUNER SET
1
4
7
2
5
8
3
6
9
%fi to move the
2
BAND
CATV
highlight bar (arrow) to
= AUTO CHANNEL SET
4
MANUAL CHANNEL SET
“MANUAL CHANNEL
SET”, then press OK or
SHUTTLE PLUS
#.
4
SELECT WITH (5,∞) AND (OK)
0
PRESS (MENU) TO END
Add or skip desired channels
4
To add channels
1
1 Press the Number
MANUAL CHANNEL SET
keys to input a
channel number you
want to add.
(CATV)
CH 45 ADD
2 Press OK or
SHUTTLE PLUS
set to “ADD”.
PRESS NUMBER KEY (0–9)
OR (5,∞), THEN (OK)
PRESS (MENU) TO END
#
to
1 5
2 –4
3 Repeat 1 and 2 to
add other channels.
2 –4
To skip channels
1 Press the Number keys or SHUTTLE PLUS %fi
to input a channel number you want to skip.
2 Press OK or SHUTTLE PLUS
3 Repeat 1 and 2 to skip other channels.
#
to set to “SKIP”.
Return to normal screen
Press MENU.
5
Setting channels manually
— Manual Channel Set
You can add the channels you want or delete the
channels you do not want manually.
Access Main Menu screen
Press MENU.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC PLAYBACK AND RECORDING
Basic
EN
15
This VCR can check the tape condition during playback
(and recording), and realizes the best possible pictures.
Load a cassette
1
Make sure the window side is up, the rear label
side is facing you and the arrow on the front of
the cassette is pointing towards the VCR.
Playback
Turn on the VCR and the TV, and select the VCR
channel 3 or 4 (or AV mode) on the TV.
Do not apply too much pressure when inserting.
● The VCR turns on automatically.
● The counter is automatically reset to “0:00:00”.
● If the cassette's record safety tab has been
removed and "REC SAFETY" is set to "ON",
playback begins automatically.
2
POWER
JOG dial
Start playback
REW
FF
2
PL
Press PLAY ( 3 ).
POWR
–
+
CH– /+
PUSH TURN
/
● Tape speed (SP or EP) is automatically detected.
● The S-VHS indicator lights up on the front
display panel when you play back a tape
recorded in S-VHS mode or in S-VHS ET mode
(੬ pg. 40)
● If “VIDEO CALIBRATION” is set to “ON”
(default setting: ੬ pg. 37, 38), “VIDEO
CALIBRATION” appears on the screen, and this
VCR checks the tape condition during
automatic tracking.
REC LINK
A.DUB
S
VIDEO
VIDEO (MONO)L—AUDIO—R
24HR QUICK
PROGRAM
SP EP
VCR
DIGITAL TBC/NR
INSERT
REC
PAUSE
STOP/EJECT
STOP/EJECT
( 7 / 0 )
POWER
● If the tape ends during playback or fast-forward
search, the cassette indication “
a few seconds and the VCR starts rewinding the
tape automatically.
” blinks for
1
4
7
2
5
8
3
6
9
2
To stop playback
Press STOP ( 7 ) on the Remote or STOP/EJECT ( 7 / 0 )
on the front panel.
4
0
To rewind the tape (when it is not running)
Press REW ( 1 ) (or turn the JOG dial on the front
panel to the left).
2
1
To fast-forward the tape (when it is not running)
Press FF ( ¡ ) (or turn the JOG dial on the front panel
to the right).
REW ( 1 )
FF ( ¡ )
To eject the tape
Press STOP/EJECT ( 7 / 0 ) on the front panel when the
tape is not running.
STOP ( 7 )
To prohibit operations during playback (Mode Lock)
Press and hold OK on the Remote for more than 5
seconds. " " and " " light up on the front display panel
(੬ pg. 60). The playback will not be interrupted until
the recording end (unrecorded portion) or tape end is
reached (੬ pg. 37, 41).
● You can also eject the cassette with the VCR turned off.
To turn off the VCR
Press POWER.
Clean the video heads using a dry
cleaning cassette — TCL-2UX —
when:
To resume the other operations, press and hold OK on
the Remote again for more than 5 seconds.
● When OK is pressed to set Mode Lock, the on-screen
display appears and the time counter remains on the
TV screen. If the time counter is not necessary, set "ON
SCREEN (PLAY)" to "OFF" ( ੬ pg. 37, 39).
• Rough, poor picture appears while a tape is played
back.
• The picture is unclear or no picture appears.
• “USE CLEANING CASSETTE” appears on the screen
(only with “ON SCREEN (PLAY)” set to “ON”: ੬ pg.
37, 39.)
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC PLAYBACK AND RECORDING (cont.)
16
EN
● To display the VCR status including the tape remaining
time, the time counter and the clock time on the TV
screen, see “Showing on-screen display” (੬ pg. 21).
● The approximate tape remaining time appears and the
Basic
Playback
Features
"
" indicator lights on the front display panel.
● The tape remaining time is calculated based on the
tape speed (SP or EP) being used. The indicated
remaining time is only an estimate.
To reset the time counter, press C. RESET on the
Remote. The counter reading becomes “0:00:00”. It is
also reset when a tape is inserted.
Checking tape position
REW
FF
PLAY
B
POWER
–
+
CH– /+
PUSH TURN
/
The tape position indicator
appears on screen in the
following cases:
REC LINK
A.DUB
S
VIDEO
VIDEO (MONO)L—AUDIO—R
24HR QUICK
PROGRAM
SP EP
VCR
DIGITAL TBC/NR
INSERT
REC
PAUSE
STOP/EJECT
● When you change the VCR
operation mode from the
stop mode to fast forward or
rewind mode.
● When you perform an Index
+
+
+
B
E
STOP/EJECT
( 7 / 0 )
COUNT
0:33:27
Search (੬ pg. 17) or Instant Review (੬ pg. 18).
F
A
The position of “ ” in relation to “B” (Beginning) or “E”
(End) shows you where you are on the tape.
–b
E
1
4
7
2
3
6
9
NOTES:
2
● "ON SCREEN (PLAY)" must be set to “ON”, or the indicator
will not appear (੬ pg. 37, 39).
5
8
0
● It may take a few seconds for the tape position indicator to be
displayed.
4
C. RESET
A
F
–C
Playing back tape repeatedly
D –2
D –1
C
— Repeat Play
You can play back a tape repeatedly.
1
While playing back a tape, press and hold PLAY ( 3 )
for more than 5 seconds.
The play indicator ( # ) on the front display panel starts
flashing slowly, and a tape will be played back
repeatedly.
F
C
STOP ( 7 )
–a, b, c
F
–a
To stop playback, press STOP ( 7 ) on the Remote or
STOP/EJECT ( 7 / 0 ) on the front panel.
● To select the returning point (recording end or tape
end), see "RETURN POINT" on page 41.
G
To prohibit operations during Repeat Play (Mode Lock)
Press and hold OK on the Remote for more than 5
seconds. " " and " " light up on the front display panel
(੬ pg. 60). The entire recording or entire tape will be
played back repeatedly without any interruption.
To cancel Mode Lock, press and hold OK on the Remote
again for more than 5 seconds.
● When OK is pressed to set Mode Lock, the on-screen
display appears and the time counter remains on the
TV screen. If the time counter is not necessary, set "ON
SCREEN (PLAY)" to "OFF" ( ੬ pg. 37, 39).
Changing display information
A
Press DISPLAY during playback.
Each time you press the button, the front display panel
shows the time counter, tape remaining time and the
clock time in sequence.
Tape Remaining Time
Time Counter
Clock Time
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
17
Adjusting tracking condition
Automatic operations after
D
F
— Tracking Adjustments
rewinding — Next Function Memory
The Next Function Memory “tells” the VCR what to do
after rewinding is complete.
● Ensure that the VCR is in stop mode.
Automatic tracking adjustment
This VCR automatically adjusts the tracking condition.
Whenever you insert a tape and start playback,
automatic tracking starts working and continuously
analyzes the signal to enable optimum picture quality
during playback.
a– For Automatic Playback Start
Press REW ( 1 ), then press PLAY ( 3 ) within
2 seconds.
Manual tracking adjustment
b– For Automatic Power Off
Press REW ( 1 ), then press POWER within
2 seconds.
If automatic tracking cannot eliminate noises well during
playback, use the manual tracking following the
procedures below.
● You can also use the manual tracking during slow
motion playback (੬ pg. 27).
c– For Automatic Timer Standby
Press REW ( 1 ), then press TIMER within
2 seconds.
1
2
Activate manual tracking
Press SP/EP on the Remote during playback.
NOTE:
It is not possible to select the Automatic Timer Standby function
if the cassette’s record safety tab is removed.
Eliminate the noises on the TV screen
Press CH + or – on the Remote.
● Press it briefly for a fine adjustment, or press and
hold for coarse adjustment. Watch the screen and
continue adjustment until optimum picture and
sound quality are achieved.
● To reactivate automatic tracking, press SP/EP on
the Remote. The automatic tracking becomes
active again.
Locating beginning of
G
recordings — Index Search
Index codes are placed on the tape at the beginning of
each recording when recording on this VCR. You can
find and automatically play back from the beginning of
any recording using the Index Search function.
Selecting monitor sound
1
2
Start search
E
While the tape is not running, press SHUTTLE PLUS
4 or ¢ on the Remote.
— Audio Monitor
You can select the desired monitor sound.
Access distant code
While playing back a tape on which stereo sound or SAP
sound is recorded, press A. MONITOR on the Remote.
Each time you press the button, sound changes as follows:
To access a recording of 2 to 9 index codes away,
press SHUTTLE PLUS 4 or ¢ repeatedly until
the correct number is displayed on screen (only if
“ON SCREEN (REC)” is set to “ON” ; ੬ pg. 37, 39).
Playback begins automatically when the desired
recording is located.
HI-FI
HI-FI L
HI-FI R
NORM
NORM
HI-FI
Beginning of the 2nd next
program recorded
Current position
on the tape
Beginning of the current
program recorded
HI-FI: Normally select this.
Hi-Fi sound is played back.
HI-FI L: Sound on the left Hi-Fi channel is played back.
HI-FI R:Sound on the right Hi-Fi channel is played back.
NORM:Sound on the normal track is played back.
NORM HI-FI:
Previous
program
recorded
Next
program
recorded
2nd next
–2
–1
1
2
3
4
¢
● If you want to find the very beginning of the
desired program, press REW ( 1 ) or FF ( ¡ )
after playback starts.
Both sounds on the Hi-Fi track and normal
track are mixed and played back.
NOTES:
NOTE:
● The above indication appears when “ON SCREEN (PLAY)” is
set to “ON” (੬ pg. 37, 39), though the monitor sound
changes in sequence.
An index code is not placed on the tape when recording is
resumed from recording pause.
● If the tape being played back has no Hi-Fi sound track, the
normal sound track will be heard regardless of this setting.
● If RF connection (੬ pg. 7) is used for viewing pictures on the
TV, sound will be monaural even though you select “HI-FI”.
● You can also use the menu to select your desired monitor
sound. (੬ pg. 40)
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC PLAYBACK AND RECORDING (cont.)
18
EN
Locating beginning of timer
H
I
recordings — Instant Review
At the press of a button, you can turn on the VCR,
rewind the tape and begin to view the most recent timer-
recorded program.
REW
FF
PLAY
POWER
–
+
CH– /+
PUSH TURN
/
REC NK
A.DUB
After ensuring that the VCR is turned off and that the
timer mode is disengaged, press REVIEW.
S
VIDEO
VIDEO (MONO)L—AUDIO—R
24HR QUICK
PROGRAM
SP EP
VCR
DIGITAL TBC/NR
INSERT
REC
PAUSE
STOP/EJECT
● The VCR turns on, and rewinds to the index code
indicating the beginning of the last timer-recorded
program, then begins playback automatically.
● You can access a program of 2 to 9 index codes away
from the current position on the tape. If, for example,
you have 5 programs recorded and you want to watch
the third one, press REVIEW three times.
● If you want to find the very beginning of the desired program,
press REW ( 1 ) or FF ( ¡ ) after playback starts.
● If the tape is already rewound when REVIEW is
pressed, it will play the tape from the beginning. It will
not fast-forward to an index code.
H
1
4
7
2
5
8
3
6
9
2
4
0
● The Instant Review function will also operate if the
VCR is turned on.
Adjusting picture condition
— Digital TBC/NR
I
1
The Digital TBC/NR (Time Base Corrector / Noise
Reduction) function removes jitter from fluctuating video
signals to deliver a stable picture even with old tapes
and rental tapes. The Digital 3-DNR (Noise Reduction)
function which cuts noise and reproduces clear pictures
is also linked to this function.
REW ( 1 )
FF ( ¡ )
We recommend that you use the Digital TBC/NR
function when...
— playing back a tape recorded on a camcorder.
— playing back a tape repeatedly used.
— using this VCR as the player for editing.
Other Useful functions for playback
● Playback Resume Function
Press DIGITAL TBC/NR on the front panel so that the
DIGITAL TBC/NR lamp lights up.
Each time you press the button, this function turns on
and off.
If there is a power outage during normal playback (or
Series Playback), the playback will resume automatically
when the power is restored to the VCR. (No setting is
required for this function.)
NOTES:
● Video Calibration (੬ pg. 38)
● If you play back a tape recorded under poor TV reception
condition, the picture may happen to become more stable
with Digital TBC/NR activated.
When this function is set to “ON”, this VCR checks the
condition of the tape in use during playback and
recording, and compensates to provide the highest-
possible pictures.
● If you play back a tape on which certain types of signals
(using a PC or some character generators) have been recorded
with Digital TBC/NR activated, the playback picture may be
distorted. In this case, deactivate Digital TBC/NR.
● Picture Control (੬ pg. 38)
● Digital TBC/NR and Video Stabilizer (੬ pg. 39) cannot be
used at the same time; if you turn on Digital TBC/NR when
“VIDEO STABILIZER” is set to “ON”, Video Stabilizer will be
automatically turned “OFF”. Make sure Digital TBC/NR is
deactivated when you want to use Video Stabilizer.
This function helps you to adjust the playback picture
quality according to your preference.
● Video Stabilizer (੬ pg. 39)
You can automatically correct vertical vibrations in the
picture when playing back unstable recordings made on
another VCR.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
19
Select recording channel
On the front panel:
Push the JOG dial, then turn it to the left or right.
2
Basic
On the Remote:
a– Press CH + or –.
or
Recording
Turn on the VCR and the TV, and select the VCR
channel 3 or 4 (or AV mode) on the TV.
b– Press the Number keys.
● If you connect the TV and the VCR only using
the RF connection, press TV/VCR on the Remote
so that the VCR mode indicator lights on the front
display panel, to view the program to be recorded.
JOG dial
POWER
PLAY ( 3 )
Set tape speed
3
4
Press SP/EP to set the recording speed.
REW
FF
PLY
POWR
–
+
Start recording
On the front panel:
Press REC ( ¶ ).
CH– /+
PUSH TURN
/
REC LINK
A.DUB
S
VIDEO
VIDEO (MONO)L—AUDIO—R
24HR QUICK
PROGRAM
SP EP
VCR
DIGITAL TBC/NR
INSERT
REC
PAUSE
STOP/EJECT
On the Remote:
While holding REC ( ¶ ), press PLAY ( 3 ).
4
PAUSE ( 8 )
● If “VIDEO CALIBRATION” is set to “ON”
(default setting: ੬ pg. 37, 38), this VCR checks
the tape condition for about seven seconds,
then starts recording. This means that the first
seven seconds of the program will not be
recorded. If this is inconvenient for you, follow
the steps below:
STOP/EJECT
( 7 / 0 )
POWER
TV/VCR
1 Press REC ( ¶ ) and PAUSE ( 8 ) to start
Video Calibration.
1
4
7
2
3
6
9
2
2 Then press PLAY ( 3 ) to start recording
after Video Calibration is complete.
5
8
0
2
–b
To pause recording
Press PAUSE ( 8 ). To resume recording, press PLAY ( 3 ).
● Pressing REC ( ¶ ) on the front panel also resumes
recording.
4
2
3
–a
To stop recording
Press STOP ( 7 ) on the Remote or STOP/EJECT ( 7 / 0 )
on the front panel.
1
To rewind the tape (when it is not running)
Press REW ( 1 ) (or turn the JOG dial on the front
panel to the left).
REW ( 1 )
FF ( ¡ )
PAUSE ( 8 )
To fast-forward the tape (when it is not running)
Press FF ( ¡ ) (or turn the JOG dial on the front panel
to the right).
4
STOP ( 7 )
To eject the tape
Press STOP/EJECT ( 7 / 0 ) on the front panel when the
tape is not running.
This VCR can check the tape condition during recording
(and playback), and realizes the best possible pictures.
● You can also eject the cassette with the VCR turned off.
Load a cassette
Make sure the record safety tab is intact. If not,
1
To turn off the VCR
set "REC SAFETY" to "OFF" ( ੬ pg. 37, 41).
Press POWER.
It may be unlawful to record or play back
copyrighted material without the consent of the
copyright owner.
● You can also record onto a cassette without a
record safety tab by covering the hole with
adhesive tape before inserting the cassette.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC PLAYBACK AND RECORDING (cont.)
20
EN
Changing display information
A
Basic
Recording
Features
Press DISPLAY during recording or recording pause.
Each time you press the button, the front display panel
shows the time counter, tape remaining time, channel
number and the clock time in sequence.
Time Counter
Clock Time
Tape Remaining Time
Channel No.
STOP/EJECT ( 7 / 0 )
● To display the VCR status including the tape remaining
time, the time counter and the clock time on the TV
screen, see “Showing on-screen display” (੬ pg. 21).
● The approximate tape remaining time appears and the
REW
FF
PLAY
POWER
–
+
CH– /+
PUSH TURN
/
"
" indicator lights on the front display panel.
REC LINK
A.DUB
S
VIDEO
VIDEO (MONO)L—AUDIO—R
24HR QUICK
PROGRAM
● The tape remaining time is calculated based on the
tape speed (SP or EP) being used. The indicated
remaining time is only an estimate.
SP EP
VCR
DIGITAL TBC/NR
INSERT
REC
PAUSE
STOP/ECT
To reset the time counter, press C. RESET on the
Remote. The counter reading becomes “0:00:00”. It is
also reset when a tape is inserted.
B
Recording on one tape
A
B
repeatedly
C
–1
1
4
7
2
5
8
3
6
9
2
— Repeat Recording
You can record programs on one tape repeatedly.
While recording, press and hold PLAY ( 3 ) and
REC ( ¶ ) on the Remote or REC ( ¶ ) on the front panel
for more than 5 seconds.
4
0
C. RESET
The record indicator on the front display panel starts
flashing slowly.
To stop recording, press STOP ( 7 ) on the Remote or
STOP/EJECT ( 7 / 0 ) on the front panel.
1
B
To prohibit operations during Repeat Recording
(Mode Lock)
Press and hold OK on the Remote for more than 5
seconds. " " and " " light up on the front display panel
(੬ pg. 60). The recording will be performed repeatedly
without any interruption.
STOP ( 7 )
D
To cancel Mode Lock, press and hold OK on the Remote
again for more than 5 seconds.
Accidental erasure prevention
To prevent accidental recording on a recorded cassette,
remove its record safety tab. To record on it later, cover the
hole with adhesive tape, or set "REC SAFETY" to "OFF".
(੬ pg. 37, 41)
● When OK is pressed to set Mode Lock, the on-screen
display appears and the time counter will be recorded
with your picture. If the time counter is not necessary,
set "ON SCREEN (REC)" to "OFF" ( ੬ pg. 37, 39).
Record safety tab
Note: You can also record onto the cassette even when the
tab is removed. (੬ pg. 41)
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
21
Watching one program while
recording another
Other useful functions for recording
C
1
● Recording Resume Function
If there is a power outage during recording (or timer
recording or Series Recording), the recording will resume
automatically when the power is restored to the VCR. (No
setting is required for this function.)
Engage TV mode
During recording...
● If you connect the TV and the VCR only using
the RF connection (੬ pg. 7) to view pictures
from the VCR
Press TV/VCR on the Remote so that VCR mode
indicator goes off from the front display panel.
(The TV broadcast being recorded disappears.)
● If you are using the AV connection (੬ pg. 7) to
view pictures from the VCR, change the TV’s
input mode from AV to TV.
● Video Calibration (੬ pg. 38)
When this function is set to “ON”, this VCR checks the
condition of the tape in use during playback and
recording, and compensates to provide the highest-
possible pictures.
● Second Audio Recording (੬ pg. 40)
This VCR’s built-in MTS decoder enables reception of
Multichannel TV Sound broadcast.
2
Select channel for viewing
Select the channel, you want to watch, on the TV.
To record a SAP program received, set “2ND AUDIO
RECORD” to “ON” using the menu screen.
NOTES:
Showing on-screen display
When the channel is changed on the VCR;
D
● The “STEREO” indication appears on the screen for about
5 seconds if the program is a stereo broadcast.
● The “SAP” indication appears on the screen for about
5 seconds if the program is a SAP broadcast.
● Both indications appear when a stereo program is
accompanied by SAP sound.
When “ON SCREEN (REC)” is set to “ON” (੬ pg. 37,
38), you can see the current VCR status on the TV
screen.
● For more detailed information about the on-screen
display, see page 61.
● S-VHS Recording Mode (੬ pg. 40)
This VCR allows you to record on an S-VHS tape with VHS
picture quality.
1
Display VCR status on TV screen
During recording or
CH 125
RECORD
PAUSE
FRI 12:00:00 AM
recording pause, press
OSD.
All indications
corresponding to the
current VCR status are
displayed for 5 seconds.
The time counter remains
11/30/01
STEREO
SAP
]SP
● S-VHS ET (੬ pg. 41)
This function allows you to record on VHS tapes with S-
VHS picture quality. Tapes recorded using this function can
be played back on a VCR equipped with the S-VHS ET
function.
+
+
+
B
E
INDEX 1
10:00
NORM
HI–FI
REMAIN
COUNT –1:23:45
on the screen indicating the elapsed time.
To prohibit operations during recording (Mode Lock)
Press and hold OK on the Remote for more than 5
seconds. " " and " " light up on the front display panel
(੬ pg. 60). No button will function and recording will
not be interrupted until it completes.
● The indications will be recorded. If you do not
want to record the superimposed operational
indications on the screen, set “ON SCREEN
(REC)” to “OFF”. (੬ pg. 37, 38)
To resume the other operations, press and hold OK on
the Remote again for more than 5 seconds.
● When OK is pressed to set Mode Lock, the on-screen
display appears and the time counter will be recorded
with your picture. If the time counter is not necessary,
set "ON SCREEN (REC)" to "OFF" ( ੬ pg. 37, 39).
2
Exit on-screen display
Press OSD again.
NOTES:
● If the VCR is in recording pause mode, “RECORD/PAUSE” is
always displayed (except when "DAY/TIME INSERT" is set to
"ON").
● The VCR status can be also displayed during playback.
Download from Www.Somanuals.com. All Manuals Search And Download.
SERIES PLAYBACK AND RECORDING
22
EN
Series Playback
To REMOTE OUT
REMOTE
IN
IN
OUT
ANTENNA IN
R
L
REMOTE
OUT
AUDIO
VIDEO
IN
OUT
VHF/UHF
TV OUT
S
V
I
D
E
O
SR-V10U-1
Mini-plug
cable
(Not supplied)
To REMOTE
IN
To
To S VIDEO OUT
AUDIO/
VIDEO
OUT
Audio/Video
Cable
S-Video Cable
(Supplied)
Mini-plug
cable
(Not supplied)
(Supplied)
To
AUDIO/
VIDEO IN
To REMOTE
OUT
To S VIDEO IN
To REMOTE IN
REMOTE
IN
IN
OUT
ANTENNA IN
R
L
REMOTE
OUT
AUDIO
VIDEO
IN
OUT
VHF/UHF
TV OUT
S
V
I
D
E
O
SR-V10U-2
To S VIDEO OUT
To AUDIO/ VIDEO OUT
S-Video Cable (Supplied)
Audio/Video Cable (Supplied)
To Audio/Video
Input
To S-Video Input
NOTE:
Series Playback is also possible using the front AUDIO/VIDEO
connectors.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
23
NOTE:
2
4
If there is a power outage during Series Playback, the playback
will resume automatically when the power is restored to the
VCR. (No setting is required for this function.)
REW
FF
PLA
POWER
–
+
To prohibit operations during Series Playback (Mode
Lock)
CH– /+
PUSH TURN
/
REC LINK
A.DUB
S
VIDEO
VIDEO (MONO)L—AUDIO—R
24HR QUICK
PROGRAM
SP EP
VCR
DIGITAL TBC/NR
INSERT
REC
PAUSE
STOP/EJECT
Press and hold OK on the Remote for more than 5
seconds. " " and " " light up on the front display panel
(੬ pg. 60). The 2 cassettes will be played back
alternately without any interruption.
To resume the other operations, press and hold OK on
the Remote again for more than 5 seconds.
● When OK is pressed to set Mode Lock, the on-screen
display appears and the time counter remains on the
TV screen. If the time counter is not necessary, set "ON
SCREEN (PLAY)" to "OFF" ( ੬ pg. 37, 39).
STOP/EJECT
( 7 / 0 )
Using two sets of SR-V10U, you can play back two
cassettes alternately as many times as you want. You can
select the returning point for Series Playback (੬ pg. 41)
Use the buttons and controls on the VCR’s front
panel for the Series Playback operations (except
when using Mode Lock).
Make connections
1
Connect two sets of SR-V10U and a TV using AV
cables as shown in the illustration on page 22.
● The mini-plug cable is a mono 3.5 mm mini-
plug to mono 3.5 mm mini-plug connector.
● When playing back S-VHS recordings, it is
recommended to use the S-VIDEO connection
to minimize picture degradation.
Turn on all components
2
After completing the connections, turn on all the
components.
● Set the TV to video input mode or A/V input
mode. Refer to the TV instruction manual.
Load cassettes
3
Insert the playback cassette into each SR-V10U.
● Set SR-V10U-2 to “AUX”. Press CH + or – to
select the input mode depending on the
connector being used -”L-1” for the rear
AUDIO/VIDEO IN connector, or “F-1” for the
front AUDIO/VIDEO input connector.
Start playback
4
Press PLAY ( 3 ) on either of SR-V10U. When the
playback reaches to the returning point (tape end
or recording end ੬ pg. 41), the other SR-V10U
successively starts to play. (The cassette will
automatically be rewound when the playback
stops.) Therefore, the cassettes loaded on two SR-
V10U will be played back alternately as many
times as you want.
To stop playback
Press STOP/EJECT ( 7 / 0 ) on the SR-V10U which is
playing back a cassette.
Download from Www.Somanuals.com. All Manuals Search And Download.
SERIES PLAYBACK AND RECORDING (cont.)
24
EN
Series Recording
Camcorder
or
Another VCR
To S Video
Output
To Audio/Video Output
Audio/Video Cable (Not supplied)
S-Video Cable (Not supplied)
To S VIDEO IN
To AUDIO/ VIDEO IN
To REMOTE OUT
Mini-plug cable
(Not supplied)
REMOTE
IN
IN
OUT
ANTENNA IN
R
L
REMOTE
OUT
AUDIO
IN
OUT
VHF/UHF
TV OUT
S
V
I
D
E
O
VIDEO
SR-V10U-1
To
REMOTE
IN
To AUDIO/
VIDEO OUT
To S VIDEO OUT
S-Video Cable (Supplied)
To S VIDEO IN
Mini-plug cable
(Not supplied)
Audio/ Video Cable
(Supplied)
To
REMOTE
OUT
To AUDIO/ VIDEO IN
REMOTE
IN
IN
OUT
ANTENNA IN
R
L
REMOTE
OUT
To REMOTE IN
AUDIO
VIDEO
IN
OUT
VHF/UHF
TV OUT
S
V
I
D
E
O
SR-V10U-2
To AUDIO/ VIDEO OUT
To S VIDEO OUT
To S Video Input
S-Video Cable (Supplied)
Audio/Video Cable (Supplied)
To Audio/Video Input
NOTE:
Select the correct input mode (“L-1” for the rear connector, “F-
1” for the front connector). (੬ step 3)
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
25
STOP/EJECT
Start recording
2
( 7 / 0 )
5
Press REC ( ¶ ) on either of SR-V10U. When the
tape remaining time reaches to 2 minutes while
recording, the other SR-V10U successively starts
to record. Therefore, recording will be continued
onto cassettes loaded on two SR-V10U
alternately.
REW
FF
PLAY
POWER
–
+
CH– /+
PUSH TURN
/
REC LINK
A.DUB
S
VIDEO
VIDEO (MONO)L—AUDIO—R
24HR QUICK
PROGRAM
SP EP
VCR
DIGITAL TBC/NR
INSERT
REC
PAUSE
STOP/EJECT
● The cassette will automatically be rewound
when the recording stops.
● Replace the cassette after rewound if you want
to continue to record onto another cassette.
5
Using two sets of SR-V10U, a long recording will be
possible (such as camcorder recording, another VCR
playback or TV broadcast).
To stop recording
Press STOP/EJECT ( 7 / 0 ) on the SR-V10U which is
recording.
Use the buttons and controls on the VCR's front
panel for the Series Recording operations (except
when using Mode Lock).
To prohibit operations during Series Recording (Mode
Lock)
Press and hold OK on the Remote for more than 5
seconds. " " and " " light up on the front display panel
(੬ pg. 60). The picture will be recorded onto the
cassettes alternately without any interruption.
To resume the other operations, press and hold OK on
the Remote again for more than 5 seconds.
● When OK is pressed to set Mode Lock, the on-screen
display appears and the time counter will be recorded
with your picture. If the time counter is not necessary,
set "ON SCREEN (REC)" to "OFF" ( ੬ pg. 37, 39).
Make connections
1
Connect two sets of SR-V10U to other
equipment, antenna or cable as shown in the
illustration on page 24.
●The mini-plug cable is a mono 3.5 mm mini-
plug to mono 3.5 mm mini-plug connector.
● When connecting a camcorder or another VCR
with an S-VIDEO output connector as recording
source, it is recommended to use the S-VIDEO
connection to minimize picture degradation.
NOTES:
● Series Recording is also possible using the front AUDIO/
VIDEO connectors.
Turn on all components
After completing the connections, turn on all the
components.
2
3
● When recording a TV broadcast, tune in the same channel on
both SR-V10U.
● Set the TV to video input mode or A/V input
mode. Refer to the TV instruction manual.
● If you do not want to record the operational indications on
the screen during Series Recording, set both “ON SCREEN
(PLAY)” and “ON SCREEN (REC)” to “OFF”. (੬ pg. 37, 38)
● If there is a power outage during Series Recording, the
recording will resume automatically when the power is
restored to the VCR. (No setting is required for this function.)
Set recording VCR's input mode
Set to “AUX“. Press CH + or – to select the input
mode depending on the connector being used –
“L-1“ for the rear AUDIO/VIDEO IN connector,
or “F-1“ for the front AUDIO/VIDEO input
connector.
Prepare for recording
Insert the recording cassette into each SR-V10U,
and prepare the playback source.
4
NOTE:
If you do not want to display the superimposed
indication on the screen during recording, set “ON
SCREEN (REC)“ to “OFF“ (੬ pg. 37, 38). If the
playback equipment has a superimpose/OSD disable
feature, set its superimpose or display feature to “OFF“
as well.
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL EFFECT PLAYBACK
26
EN
Locating particular scene
A
Special Effect
Playback
rapidly — Picture Search
7 High-Speed Picture Search:
You can rapidly locate a particular scene on the tape.
On the front panel:
Possible during normal playback.
To do forward picture search, turn the JOG dial quickly
to the right.
To do reverse picture search, turn the JOG dial quickly
to the left.
A
PLAY ( 3 )
D E
B
● If you release the dial, picture search continues.
REW
FF
On the Remote:
PL
POWER
–
+
Possible during normal playback or still picture
playback.
CH– /+
PUSH / TURN
REC LINK
A.DUB
S
VIDEO
VIDEO (MONO)L—AUDIO—R
24HR QUICK
PROGRAM
SP EP
VCR
DIGITAL TBC/NR
INSERT
REC
PAUSE
STOP/EJECT
To do forward picture search, press FF (
).
To do reverse picture search, press REW (
).
● If you press and hold the button for more than
2 seconds, simply releasing it cancels the picture
search, and normal playback resumes.
B D
F
To resume normal playback, press PLAY ( 3 ).
7 Variable-Speed Picture Search:
Possible during normal playback.
You can change the speed of picture search.
1
4
7
2
3
6
9
2
5
8
0
How to use the JOG dial on the front panel:
Turn the JOG dial to the right (forward search) or to the
left (reverse search).
Each time the JOG dial passes a click position, picture
search speed changes (see the diagram below).
If you release the dial, picture search continues.
● The speed of picture search is determined by the
number of click stops of the JOG dial.
4
C
A
1
A
PLAY ( 3 )
B
D
A D
E
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
27
How to use the SHUTTLE PLUS buttons on the Remote:
To do forward picture search, press SHUTTLE PLUS
¢ repeatedly.
Each time you press the button, the search speed
increases.
Viewing still picture frame by
D
frame — Frame-by-Frame Playback
On the front panel:
During normal playback:
● To decrease the speed while forward picture search
(toward normal playback, then reverse picture search),
press SHUTTLE PLUS 4 repeatedly.
Push the JOG dial or press PAUSE ( 8 ) to pause.
To advance a still picture, turn the JOG dial to the right.
To reverse a still picture, turn the JOG dial to the left.
On the Remote:
During normal playback:
Press PAUSE ( 8 ) to pause.
To do reverse picture search, press SHUTTLE PLUS 4
repeatedly.
Each time you press the button, the search speed
increases while reverse picture search.
● To decrease the speed while reverse picture search
(toward normal playback, then forward picture
search), press SHUTTLE PLUS ¢ repeatedly.
To advance a still picture, press SHUTTLE PLUS ¢ (or
PAUSE ( 8 )) repeatedly.
To reverse a still picture, press SHUTTLE PLUS 4
repeatedly.
To resume normal playback, press PLAY ( 3 ).
To resume normal playback, press PLAY ( 3 ).
C
Viewing slow motion picture
— Slow Motion Playback
E
SHUTTLE
PLUS
On the front panel:
During normal playback:
Reverse
Forward
Turn the JOG dial to the first or second click-stop to the
left (forward slow motion) or to the third or fourth click-
stop to the left (reverse slow motion) so that slow motion
playback starts. If you release the dial, slow motion
playback continues.
Reverse
play
Forward
search
Reverse
search
Slow
motion
Normal
Play
Reverse
slow motion
3 steps
2 steps
2 steps
4 steps
● Holding PAUSE ( 8 ) for more than 2 seconds also
starts forward slow motion playback.
Viewing still picture
— Still Picture Playback
B
On the Remote:
● During normal playback:
Press SHUTTLE PLUS 4 to decrease the playback
On the front panel:
Push the JOG dial during normal playback.
speed.
Each time you press the button, the speed decreases
(toward reverse slow motion playback, then reverse
picture search).
● Holding PAUSE ( 8 ) for more than 2 seconds also
starts forward slow motion playback.
On the front panel or the Remote:
Press PAUSE ( 8 ) during normal playback.
Playback is freezed and a still picture appears.
To resume normal playback, press PLAY ( 3 ).
To resume normal playback, press PLAY ( 3 ).
NOTE:
To obtain a noiseless still picture, it may be necessary to adjust
tracking in slow motion playback before starting still picture
playback.
● During still picture playback:
Press and hold SHUTTLE PLUS ¢ to start forward (or
SHUTTLE PLUS 4 to start reverse) slow motion
playback. When you release the button, slow motion
playback stops and a still picture appears.
● Holding PAUSE ( 8 ) for more than 2 seconds also
starts forward slow motion playback.
Skipping unwanted portions
C
— Skip Search
You can skip over (view at high speed) unwanted
portions of the tape.
To resume normal playback, press PLAY ( 3 ).
Press SKIP SEARCH once to 4 times during playback.
Each press initiates a 30-second period of high speed
playback (up to 2 minutes). When the specified portion
of the tape is skipped, normal playback resumes
automatically.
NOTE:
Manual tracking is possible during slow motion playback.
During slow motion playback, simply press CH + or – on the
Remote to adjust tracking.
To return to normal playback during Skip Search, press
PLAY ( 3 ).
Download from Www.Somanuals.com. All Manuals Search And Download.
TIMER RECORDING
28
EN
Timer recording allows you to program the VCR to
automatically record a broadcast at some future time.
Up to 8 timer recording programs can be made using
VCR Plus+ timer programing, Express timer programing
(੬ pg. 32) or 24HR quick programing method
VCR Plus+®
Timer
Programing
(੬ pg. 34) as far as a year in advance.
The VCR Plus+ timer programing system eliminates the
need to input channel, date, start and stop time data
when programing timer recording settings. Simply key in
the PlusCode number for the TV broadcast you wish to
record and the VCR’s timer will be automatically
programed. (The PlusCode programing numbers are the
numbers next to the program in most TV listing.)
Turn on the VCR and the TV, and select the VCR
channel 3 or 4 (or AV mode) on the TV.
Load a cassette
1
Make sure the record safety tab is intact. If not,
set "REC SAFETY" to "OFF" ( ੬ pg. 37, 41).
● The VCR turns on, and the counter is reset,
automatically.
● You can also record onto a cassette without a
record safety tab by covering the hole with
adhesive tape before inserting the cassette.
POWER
1
4
7
2
5
8
3
6
9
Access PlusCode No. screen
2
2
Press PROG. on the
3 4
WEEKLY
8
PLUSCODE NO.
DAILY
Remote.
● The clock must be set
4
0
CANCEL
STOP +/–
to access the
PlusCode No. screen.
If you have not set the
clock, the Main Menu
PRESS NUMBER KEY (0–9)
PRESS (+/–) TO SET
EXPRESS PROGRAMMING
PRESS (PROG.) TO END
4
screen appears after
2 7
1
6
an error message is displayed. Refer to page 8
for the Plug & Play setting or page 10 for the
clock setting procedure.
Enter PlusCode number
3
3 4 7
Press the appropriate
PLUSCODE NO.
Number keys to input
the PlusCode number
4
123
printed in the TV
listings for the TV
broadcast you wish to
record, then press OK.
PRESS NUMBER KEY (0–9)
THEN (OK)
PRESS (PROG.) TO END
Then;
If the Guide Channel Set screen appears
— go to step 4.
If the VCR Plus+ Program screen appears
— go to step 5.
● To make corrections, press CANCEL and input
the correct PlusCode number.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
29
Input receiving channel number
Return to normal screen
4
5
7
8
The guide channel
Press PROG. or OK.
GUIDE CHANNEL SET
number, which is
“PROGRAM COMPLETED” appears on the
screen for about 5 seconds, then normal screen
appears.
GUIDE CH: 12
VCR CH : –––
assigned to the TV or
cable station for the
PlusCode number that
you entered in step 3,
will appear
• If “PROGRAM NOT COMPLETED PROGRAM
OVERLAP” appears, you have another program
overlapping the program you have just made.
The Program Check screen appears and
conflicting programs will start blinking.
You can now correct the conflicting programs.
See “When programs overlap each other” on
page 36.
PRESS NUMBER KEY (0–9)
OR (5,∞), THEN (OK)
PRESS (PROG.) TO END
automatically on the
Guide Channel Set screen.
Press the Number keys (or CH +/– or SHUTTLE
PLUS %fi) to input the number of the channel on
which the broadcast for the PlusCode number is
received on the VCR, then press OK.
● The Guide Channel Set screen appears only
when you input the PlusCode number of a
station for which the guide channel number has
not been set previously.
● If you receive your channels through a cable
box, select the cable box output channel — the
channel on which you view the cable box
programs on the TV.
Engage timer recording standby mode
Press TIMER.
The VCR turns off automatically and “‰” is
displayed on the front display panel.
To use the VCR while it is in timer recording standby
mode
Press TIMER to cancel the timer recording standby
mode, then press POWER to turn on the VCR.
DO NOT forget to put the VCR into timer recording standby
mode again by pressing TIMER after you use the VCR;
otherwise, you cannot record the broadcasts you want.
● When “AUTO TIMER” is set to “ON” (੬ pg. 37, 38) ,
the timer recording standby mode is automatically
engaged when the VCR is turned off. It is temporarily
canceled when the VCR is turned on. You do not have to
press TIMER to engage or disengage the timer recording
standby mode.
Check program date
The PlusCode number you entered and the
corresponding timer
recording program is
displayed on the
Program screen. Check
to make sure it is
accurate.
PROGRAM 1
(PLUSCODE NO. 12345678)
START
8:00PM
DATE
12/24/00
SUN
STOP
10:00PM
CH
=
12 SP
PRESS (8=DAILY, 9=WEEKLY
STOP+/– = STOP TIME, SP/EP)
PRESS (PROG.) TO END
● To change the stop
time, press STOP +/–.
● To timer-record daily (Sunday–Saturday) or
weekly serials, press DAILY (number “8”) or
WEEKLY (number “9”). “DAILY” or “WEEKLY”
appears on the Program screen.
Pressing the button again makes each
corresponding display disappear.
● If you made a mistake, press CANCEL to access
the PlusCode No. screen again and input the
correct PlusCode number.
IMPORTANT
If you have moved to a different area or if a broadcasting
station’s channel number has been changed, the wrong
VCR CH number will be displayed on the Program screen
in step 5. When this happens, set the correct guide
channel number for that station. (੬ pg. 30, “Changing
VCR Plus+ Setting”)
● If an incorrect PlusCode number or the one for
a broadcast already finished has been inputted,
“ERROR” is displayed for about 5 seconds, then
the PlusCode No. screen reappears.
NOTES:
● In case of a power failure after programming, the recorder's
memory backup keeps your selections (if the lithium battery is
not exhausted).
● To timer-record cable channels received through a cable box,
be sure to keep the cable box turned on with the correct
channel selected.
Set tape speed
Press SP/EP.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
TIMER RECORDING (cont.)
30
EN
IMPORTANT
Changing
VCR Plus+®
Setting
If you have moved to a different area or if a broadcasting
station’s channel number has been changed, the wrong
VCR CH number will be displayed on the
Program screen (੬ step 5 on page 29). When this
happens, perform the following steps to set the correct
guide channel number for that station.
To ensure that VCR Plus+ timer recording operates
correctly, it is necessary to set the VCR Plus+ “Guide
Channel Set” for each station. Read the following
information carefully.
Turn on the VCR and the TV, and select the VCR
channel 3 or 4 (or AV mode) on the TV.
VCR Plus+ guide channel matching
The VCR Plus+ programing system assigns a VCR Plus+
guide channel to the TV channels and the cable
channels. These guide channel numbers are also called
the VCR Plus+ channel codes. Most TV listings have a
section, usually a chart, indicating the guide channel
numbers assigned to each station. For accurate VCR
Plus+ programing, the VCR Plus+ guide channel number
for each station should match the channel number on
which it is received in your area.
1
4
7
2
5
8
3
6
9
2
4 5
4
0
NOTES:
● In many instances, the VCR Plus+ guide channel numbers for
cable and broadcast TV stations DO NOT match the channel
number on which it is received by your VCR or cable box.
Check your TV listing, or contact your cable supplier for
details.
1
● Many TV stations can be viewed on cable. Check your TV
listing, or contact your cable supplier for details.
1 6
2 –5
2 –5
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
31
Access Main Menu screen
Input receiving channel number
1
2
5
6
Press MENU.
Press the Number keys
(Ex.) If WNJU(Ind.) is
or SHUTTLE PLUS %fi
to input the number of
the channel on which
the guide channel’s
broadcasts are received,
then press OK or
received on channel 47
Access Initial Set screen
Press SHUTTLE PLUS
%fi to move the
GUIDE CHANNEL SET
MAIN MENU
FUNCTION SET
GUIDE CH
VCR CH : 47
:
6
highlight bar (arrow) to
“INITIAL SET”, then
press OK or SHUTTLE
= TUNER SET
INITIAL SET
SHUTTLE PLUS
#.
PRESS NUMBER KEY (0-9)
OR (5,∞), THEN (OK)
PRESS (MENU) TO END
PLUS
#.
● Repeat steps 4 and 5
PRESS (5,∞), THEN (OK)
PRESS (MENU) TO END
for each instance.
● If you receive your channels through a cable
box, select the cable box output channel — the
channel on which you view the cable box
programs on the TV.
Access Guide Channel Set screen
Press SHUTTLE PLUS
3
4
INITIAL SET
%fi to move the
= CLOCK SET
highlight bar (arrow) to
“GUIDE CHANNEL
SET”, then press OK or
GUIDE CHANNEL SET
Return to normal screen
Press MENU.
SHUTTLE PLUS
#.
SELECT WITH (5,∞) AND (OK)
PRESS (MENU) TO END
Input guide channel number
Press the Number keys
(Ex.) When inputting the
or SHUTTLE PLUS %fi
to input the VCR Plus+
guide channel number
as shown in the TV
guide channel number 6
for WNJU(Ind.)
GUIDE CHANNEL SET
GUIDE CH :
VCR CH : – – –
6
listing, then press OK or
SHUTTLE PLUS
#.
PRESS NUMBER KEY (0-9)
OR (5,∞), THEN (OK)
PRESS (MENU) TO END
Download from Www.Somanuals.com. All Manuals Search And Download.
TIMER RECORDING (cont.)
32
EN
You can directly program the VCR’s timer to record up to
8 programmes, as far as a year in advance. Remember,
the clock must be set before you can program the timer
(੬ pg. 8 or 10).
Express Timer
Programing
Load a cassette
Make sure the record safety tab is intact. If not,
set "REC SAFETY" to "OFF" ( ੬ pg. 37, 41).
1
Turn on the VCR and the TV, and select the VCR
channel 3 or 4 (or AV mode) on the TV.
● The VCR turns on, and the counter is reset,
automatically.
● You can also record onto a cassette without a
record safety tab by covering the hole with
adhesive tape before inserting the cassette.
Access PlusCode No. screen
2
3
Press PROG..
Access Program screen
Press START +/– once.
POWER
PROGRAM 1
(If no program is stored,
“PROGRAM 1”
appears.)
START
– –:– –AM
DATE
STOP
– –:– –AM
CH
1
4
7
2
5
8
3
6
9
=
2
– –/– –/– –
––– SP
DAILY
PRESS (+/–, SP/EP, 8=DAILY,
9=WEEKLY), THEN (0K)
PRESS (PROG.) TO END
WEEKLY
0
4
0
3 4
5
2 9
7
Set program start time
Press START +/–
repeatedly to enter the
time you want
6
8
4
5
1
PROGRAM 1
START
8:00 AM
DATE
STOP
– –:– –AM
CH
=
recording to start.
– –/– –/– –
––– SP
● Press and hold START
+/– to increase the
time in 30-minute
intervals.
PRESS (+/–, SP/EP, 8=DAILY,
9=WEEKLY), THEN (0K)
PRESS (PROG.) TO END
9
Set program stop time
Press STOP +/– repeatedly to enter the time you
want recording to stop.
● Press and hold STOP +/– to increase the time in
30-minute intervals.
Set program date
Press DATE +/–. (The current date is displayed on
the screen. The date you enter appears in its
place.)
6
7
Set channel number
Press CH +/–.
● Holding down CH +/– rapidly changes the
channel numbers.
● If you receive your programs through a cable
box, select the cable box output channel — the
channel on which you view the cable box
programs on the TV.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
33
Set tape speed
NOTES:
8
9
● In case of a power failure after programming, the recorder's
memory backup keeps your selections (if the lithium battery is
not exhausted).
Press SP/EP to set the tape speed.
Return to normal screen
Press PROG. or OK.
“PROGRAM COMPLETED” appears on the
screen for about 5 seconds, then normal screen
appears.
● Programs that start after midnight must have the next day’s
date.
● After timer recording is completed, the VCR turns off
automatically.
● You can program the timer recording while a regular
recording is in progress.
● To timer-record cable channels, be sure to keep the cable box
turned on with the correct channel selected.
• If “PROGRAM NOT COMPLETED PROGRAM
OVERLAP” appears, you have another program
overlapping the program you have just made.
The Program Check screen appears and
conflicting programs will start blinking.
You can now correct the conflicting programs.
See “When programs overlap each other” on
page 36.
Engage timer recording standby mode
0
Press TIMER.
The VCR turns off automatically and “‰” is
displayed on the front display panel.
To timer-record daily (Sunday–Saturday) or weekly
serials
Press DAILY (number “8”) or WEEKLY (number “9”)
anytime during steps 3 through 9.
“DAILY” or “WEEKLY” appears on the Program screen.
● Pressing the button again makes the corresponding
indication disappear.
To use the VCR while it is in timer recording standby
mode
Press TIMER to cancel the timer recording standby
mode, then press POWER to turn on the VCR.
DO NOT forget to put the VCR into timer recording
standby mode again by pressing TIMER after you use the
VCR; otherwise, you cannot record the broadcast you
want.
● When “AUTO TIMER” is set to “ON” (੬ pg. 37, 38),
the timer recording standby mode is automatically
engaged when the VCR is turned off. It is temporarily
canceled when the VCR is turned on. You do not have
to press TIMER to engage or disengage the timer
recording standby mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
TIMER RECORDING (cont.)
34
EN
You can program a timer recording that starts within
24 hours. Up to 8 timer recording programs can be
made as far as a year in advance. Remember, the clock
must be set before you can program the timer (੬ pg. 8
or 10).
24HR Quick
Programing
Load a cassette
Make sure the record safety tab is intact. If not,
cover the hole with adhesive tape, then load it
into the VCR.
1
JOG dial
● The VCR turns on, and the counter is reset,
automatically.
REW
FF
PLAY
Access 24HR quick program display.
POWER
–
+
2
CH– /+
PUSH TURN
/
Push 24HR QUICK PROGRAM. “ ” and start
REC LINK
A.DUB
S
VIDEO
VIDEO (MONO)L—AUDIO—R
24HR QUICK
PROGRAM
time start blinking on the display panel.
Program start time indicator
SP EP
VCR
DIGITAL TBC/NR
INSERT
REC
PAUSE
STOP/EJECT
24HR QUICK
PROGRAM
Set program start time
3
Turn the JOG dial to the left or right. Then, push
the JOG dial. “ ” and start time start blinking on
the display panel.
NOTES:
Program start time indicator
● If “Err” appears on the display panel, repeat the steps again.
● When a menu screen is shown, you cannot use 24HR quick
programing function. Press MENU to return to normal screen,
and try again.
● You can use 24HR quick programing function also when the
VCR is turned off.
● For 24HR quick programing function, the program overlap
warning display does not appear even if some programs
overlap each other.
● In case of a power failure after programming, the recorder's
memory backup keeps your selections (if the lithium battery is
not exhausted).
● One click stop of the JOG dial changes the
time in 5-minute intervals.
Set program stop time
Turn the JOG dial to the left or right. Then, push
the JOG dial and channel number will start
4
blinking.
Program stop time indicator
● One click stop of the JOG dial changes the
time in 5-minute intervals.
Set channel number
Turn the JOG dial to the left or right.
5
Timer warning display
A warning appears on the
TV screen to tell you that
the timer-recording is to
start in 5 minutes if you
are not in the timer
–WARNING–
TIMER RECORDING
● You can cancel the setting at any time by
pressing and holding the JOG dial for more
than 3 seconds. Repeat from the step 3.
TO START SOON
(CANCEL)
recording standby mode at
that time. Press TIMER to
put the VCR into timer
recording standby mode. To clear the display, press
CANCEL on the Remote.
Engage timer recording standby mode
6
Press 24HR QUICK PROGRAM.
The VCR turns off automatically and “‰” is
displayed on the front display panel.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
35
Turn on the VCR and the TV, and select the VCR
channel 3 or 4 (or AV mode) on the TV.
Checking program settings
A
1
Disengage timer
Press TIMER, then press POWER.
● When “AUTO TIMER” is set to “ON” (੬ pg. 37,
38), you do not have to press TIMER.
2
3
Access Program Check screen
A
–1
Press PROG. CHECK.
PR START STOP CH DATE
1
2
3
4
5
6
7
8
8:00P 10:00 12 12/24
10:00A 10:45 40 12/25
1
4
7
2
5
8
3
6
9
11:30P
1:00 125 12/25
2
PRESS (CHECK) TO NEXT
4
0
B
–2
A
B
–1 B
–4
Access Program screen
Press PROG. CHECK again to check more detailed
information. Each time you press PROG. CHECK,
the next program’s Program screen appears. When
all Program screens are shown, normal screen
resumes.
–2
1
A
B
–2, 3
B
–2
–3
Canceling or changing program
settings
B
1
2
Access Program screen
Repeat steps 1 to 3 above.
Cancel or change program setting
To cancel a program, press CANCEL when the
Program screen you do not want is shown.
To change a program, press the appropriate button:
START+/–, STOP+/–, DATE+/–, CH+/–, and/or SP/
EP when the Program screen on which you want to
make changes is shown.
3
4
Return to normal screen
Press PROG. CHECK as many times as necessary
until no Program screen is shown.
Other Useful functions for timer recording
You can also use the following functions for timer
recording.
Reengage timer recording standby mode
Press TIMER.
● Auto Timer (੬ pg. 38)
● When “AUTO TIMER” is set to “ON” (੬ pg. 37,
38), the timer recording standby mode
automatically resumes when you turn off the
VCR.
When “AUTO TIMER” is set to “ON”, the timer recording
standby mode is automatically engaged when the VCR is
turned off. It is temporarily canceled when the VCR is
turned on. You do not have to press TIMER to engage or
disengage the timer recording standby mode.
● Auto SP = EP Timer (੬ pg. 39)
If there is not enough tape to record the entire broadcast
for recording in SP mode, the VCR automatically switches
to EP mode to allow complete recording. This feature is
especially handy when recording a broadcast of more than
2 hours in length.
Download from Www.Somanuals.com. All Manuals Search And Download.
TIMER RECORDING (cont.)
36
EN
3
Cancel or change program setting
To cancel a program,
press CANCEL when the
Program screen you do
not want is shown.
“PROGRAM
COMPLETED” appears on
the screen for about
5 seconds, then normal
screen appears.
PROGRAM 4
START
9:00 PM
DATE
STOP
=
10:00PM
CH
12/24/00
SUN
10 SP
1
4
7
2
5
8
3
6
9
2
PRESS (CANCEL) TO CANCEL
PRESS (OK) TO CONFIRM
PRESS (PROG.) TO END
4
C
0
–3
To change a program, press the appropriate button:
START+/–, STOP+/–, DATE+/–, CH+/–, and/or SP/
EP when the Program screen on which you want to
make changes is shown, then press OK.
“PROGRAM COMPLETED” appears on the screen
for about 5 seconds, then normal screen appears.
C
C
–3
1
–3
NOTE:
If the overlap is not yet solved or another overlap occurs
with the timer program setting made last after making
correction on a program, the conflicting programs will be
shown on the Program Check screen again. Repeat the
above steps again until the overlap is solved.
C
C
C
–3
–2
–2
ATTENTION
If there is a conflict in the timer schedule and one program
overlaps with another, only the parts shown below in gray
will be recorded.
When programs overlap each
other
C
If “PROGRAM NOT COMPLETED PROGRAM
OVERLAP” appears, you have another program
overlapping the program you have just made.
The Program Check screen appears and conflicting
programs will start blinking.
Pattern 1:
The program with the lower program
number will be recorded.
10:00
11:00
12:00
Program 1
CH10
CH40
Not recorded
Program 2
PR START STOP CH DATE
Pattern 2:
The program starting earlier will be
recorded.
1
2
3
4
5
6
7
8
8:00P 11:00
12 12/24
PROGRAM NOT COMPLETED
PROGRAM OVERLAP
10:00A 10:45 40 12/25
11:30P
1:00 125 12/25
10:00
11:00
12:00
9:00P 10:00
10 12/24
CH10
Program 1
Not recorded
Program 2 CH40
(5,∞), THEN (
3) (PROG.) : END
Pattern 3:
The program starting earlier will be
recorded, followed by the remaining portion
of the other program.
EX. Program 1 (you have just made) and Program 4
overlap each other
10:00
11:00
12:00
CH10
Program 1
1
2
Confirm overlapping programs
CH40
Program 2
Overlapping programs blink on the screen.
Not recorded
Select program to modify
Press SHUTTLE PLUS %fi, then press SHUTTLE
PLUS
#.
• You can only select one of the overlapping
programs.
NOTE:
If you do not mind this overlap, press PROG. to finish the
timer program setting. See “ATTENTION” to the right.
Without doing anything for about 1 minute, the VCR will
finish the timer programing.
Download from Www.Somanuals.com. All Manuals Search And Download.
OTHER USEFUL FUNCTIONS
EN
37
You can use the other useful function settings on the
Function Set screen by following the procedure
described below.
● For the functions you can set on the Function Set
screen, see pages 38 to 41.
Useful Function
Settings
Access Main Menu screen
1
2
Press MENU.
Turn on the VCR and the TV, and select the VCR
channel 3 or 4 (or AV mode) on the TV.
Access Function Set screen
Press SHUTTLE PLUS
MAIN MENU
%fi to move the
=
FUNCTION SET
TUNER SET
highlight bar (arrow) to
“FUNCTION SET”, then
press OK or SHUTTLE
INITIAL SET
PLUS
#.
PRESS (5,∞), THEN (OK)
PRESS (MENU) TO END
1
4
7
2
5
8
3
6
9
2
Select Function.
3
Press SHUTTLE PLUS %fi to move the highlight
bar (arrow) to the function you want to set.
4
0
FUNCTION
PREVIOUS PAGE
= PREVIOUS PAGE
REAR AUX INPUT
=
VIDEO CALIBRATION
VIDEO
OFF
=
DIGITAL R3
PICTURE CONTROL
AUTO TIMER
S-VHS ET
VIDEO STABILIZER
2ND AUDIO RECORD
RETURN POINT TAPE END
ON SCREEN (REC)
ON SCREEN (PLAY)
AUTO SP=EP TIMER
NEXT PAGE
DAY/TIME INSERT
OFF
ON
NORM
AUDIO MONITOR
REC SAFETY
S-VHS MODE
FRONT AUX INPUT
NEXT PAGE
DAILY T. RECORD
1
SELECT WITH (5,∞) AND
SELECT WITH (5,∞) AND (OK)
SELECT WITH (5,∞) AN
PRESS (MENU) TO END
PRESS (MENU) TO END PRESS (MENU) TO END
Change setting
4
5
Press OK or SHUTTLE PLUS
#.
1 5
2 4
2 3
Return to normal screen
Press MENU.
Download from Www.Somanuals.com. All Manuals Search And Download.
OTHER USEFUL FUNCTIONS (cont.)
38
EN
* The default setting is bold in the table below.
When this function is set to “ON”, this VCR checks the condition of the
tape in use during playback and recording, and compensates to provide
the highest-possible pictures. This takes place whenever you play back a
tape or start recording after inserting a tape.
Ⅵ VIDEO CALIBRATION
ON
OFF
NOTES:
● During playback, this function is always working even though “VIDEO
CALIBRATION” appears just at the beginning of automatic tracking.
● During recording, this function works only for the first EP recording and the first
SP recording on an inserted tape.
For timer recording, this function checks the tape condition both for the SP
recording and the EP recording before the first timer recording starts.
● When you play back rental tapes or tapes recorded on other VCRs, set this
function either “ON” or “OFF” whichever gives you the best picture.
This function helps you to adjust the playback picture quality according
to your preference.
Ⅵ PICTURE CONTROL
AUTO (NORM): Normally select
this. Picture quality is
NOTES:
adjusted automatically.
When “VIDEO
CALIBRATION” is “OFF”,
“NORM” will appear instead
of “AUTO”.
● When you select “EDIT”, “SOFT” or “SHARP”, the selected mode will not
change until you select again.
● Select "EDIT" when you are editing tapes (੬ pg. 45, 46, and 49). After you
finish editing the tapes, select “AUTO” (“NORM” when “VIDEO
CALIBRATION” is “OFF”.)
EDIT: Minimizes picture
degradation during editing
(recording and playback).
SOFT: Reduces image
coarseness when viewing
overplayed tapes
containing much noise.
SHARP: Clearer, sharper-edged
picture when viewing
images with much flat,
same-colored surfaces
such as cartoons.
● When this function is set to “ON”:
Ⅵ AUTO TIMER
The timer recording standby mode is automatically engaged when the
VCR is turned off. It is temporarily canceled when the VCR is turned
on. You do not have to press TIMER to engage or disengage the timer
recording standby mode.
ON
OFF
● When this function is set to “OFF”:
You have to press TIMER to engage or disengage the timer recording
standby mode.
When this function is set to “ON”, all the indications displayed on
screen will be recorded. If you do not want to record the indications,
select “OFF”. (੬ pg. 21)
Ⅵ ON SCREEN (REC)
ON
OFF
NOTE:
● The setting you have made is kept in memory. Even if the VCR is unplugged or
the power failure occurs, it will resume every time you turn on the VCR. (੬ pg.
9)
Refer to page 37 for setting procedures.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
39
* The default setting is bold in the table below.
When this function is set to “ON”, various VCR status information (on-screen
display) appears on the screen during playback.
Ⅵ ON SCREEN (PLAY)
ON
OFF
NOTES:
● When you use this VCR as the playback VCR for editing a tape, be sure to set this
function to “OFF”; otherwise, the VCR status information (on-screen display) will be
recorded on the edited tape.
● If you select a channel on which no signal is received, the channel number is
displayed regardless of this function setting.
● The setting you have made is kept in memory. Even if the VCR is unplugged or the
power failure occurs, it will resume every time you turn on the VCR. (੬ pg. 9)
Ⅵ AUTO SP = EP TIMER
When this function is set to “ON”, the VCR automatically switches to EP
mode to allow complete recording if there is not enough tape to record the
entire program while timer-recording in SP mode.
ON
OFF
For Example . . .
Recording a program of 140 minutes in length onto a 120-minute tape
Approximately 110 minutes
SP mode
Approximately 30 minutes
EP mode
Make sure you set this function to “ON” before the timer-recording starts.
NOTES:
● If you have programed the VCR to timer-record 2 or more programs, the second
program and those thereafter may not fit on the tape with this function set to "ON". In
this case, do not use this function, but change the tape speed manually during timer
programing.
● In order to ensure that the recording fits on the tape, this function may leave a slight
non-recorded portion at the end of the tape.
● There may be some noise and sound disturbance where the tape speed switches from
SP to EP mode on the tape.
● This function will not work properly on the following tapes: T(ST)-30, T(ST)-60, T(ST)-
90, and T(ST)-120.
When this function is set to “ON”, edge correction to the luminance signal is
performed to enhance details. Normally set this function to “ON”.
Ⅵ DIGITAL R3
ON
OFF
NOTES:
● Depending on the type of tape being used, picture quality may be better with
“DIGITAL R3” set to “OFF”.
● If you use this VCR as the playback VCR for editing, be sure to set “DIGITAL R3” to
“OFF” before starting.
When this function is set to “ON”, you can automatically correct vertical
vibrations in the picture when playing back unstable recordings made on
another VCR.
Ⅵ VIDEO STABILIZER
ON
OFF
NOTES:
● When you finish viewing a tape, be sure to set this function to “OFF”.
● Regardless of the setting, this function has no effect during recording and during
special effects playback.
● The on-screen display may jitter vertically when this function is set to “ON”.
● To watch recordings with close-caption, set this function to “OFF”.
Refer to page 37 for setting procedures.
Download from Www.Somanuals.com. All Manuals Search And Download.
OTHER USEFUL FUNCTIONS (cont.)
40
EN
* The default setting is bold in the table below.
When this function is set to “ON”;
Ⅵ 2ND AUDIO RECORD
● If a SAP program is received, the SAP audio is recorded on both the
normal and Hi-Fi tracks. The main audio is not recorded.
● If a non-SAP program is received, the main audio is recorded on both
the Hi-Fi and normal tracks.
ON
OFF
When this function is set to “OFF”, the SAP audio cannot be recorded.
This VCR can record two sound tracks simultaneously (normal and Hi-
Fi) on a tape.
You can select the sound track(s) to listen to while playing back a Hi-Fi
stereo tape.
In addition, when playing back a prerecorded tape containing two
separate audio programs on the Hi-Fi tracks, you can choose either one
by selecting either “HI-FI L” or “HI-FI R”.
Ⅵ AUDIO MONITOR
HI-FI: Normally select this.
Hi-Fi sound is played
back.
HI-FI L: Sound on the left Hi-Fi
channel is played back.
HI-FI R: Sound on the right Hi-Fi
channel is played back.
NORM: Sound on the normal track
is played back.
NOTES:
● While playing back a monaural tape, sounds on the normal track will be heard
regardless of this setting.
MIX:
Both sounds on the Hi-Fi
track and normal track are
mixed and played back.
● If RF connection (੬ pg. 7) is used for viewing pictures on the TV, sound will be
monaural even though you select “HI-FI”.
● You can also use the A. MONITOR button on the Remote to select the desired
monitor sound. (੬ pg. 17)
You can determine which recording mode — either S-VHS mode or VHS
mode — is used for recording on S-VHS tapes.
Ⅵ S-VHS MODE
ON
OFF
When this function is set to “ON”, you can record on S-VHS tapes with
S-VHS picture quality.
When this function is set to “OFF”, you can record on S-VHS tapes with
VHS picture quality.
NOTES:
• S-VHS mode allows you to make high quality video recordings with horizontal
resolution of 400 lines, comparing with the 230 lines of resolution of
conventional VHS recordings. To achieve the highest quality picture we
recommended to record in S-VHS mode. (But remember that a conventional
VHS VCR without SQPB cannot play back S-VHS tapes recorded in S-VHS
mode.)
• S-VHS MODE setting does not affect recording on VHS tapes. Recording on
VHS tapes is always performed in VHS mode except when using S-VHS ET
mode (੬ pg. 41).
You have to select which terminal — either VIDEO (composite) or S
VIDEO (Y/C separate signals) — to use as the video input terminal on the
front panel.
Ⅵ FRONT AUX INPUT
VIDEO
S-VIDEO
Make sure to select the correct terminal; otherwise, you may fail in
recording (editing) on this VCR.
You have to select which terminal — either VIDEO (composite) or S
VIDEO (Y/C separate signals) — to use as the video input terminal on the
rear panel.
Ⅵ REAR AUX INPUT
VIDEO
S-VIDEO
Make sure to select the correct terminal; otherwise, you may fail in
recording (editing) on this VCR.
Refer to page 37 for setting procedures.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
41
* The default setting is bold in the table below.
This function allows you to record on VHS tapes with S-VHS picture
quality. Tapes recorded using this function can be played back on a VCR
equipped with the S-VHS ET function. The S-VHS indicator lights up on
the front display panel when "S-VHS ET" is set to "ON".
Ⅵ S-VHS ET
ON
OFF
NOTES:
● Before recording, make sure that “VIDEO CALIBRATION” is set to “ON”. (੬ pg. 37,
38)
● You cannot activate the S-VHS ET function...
– while recording is in progress.
– while timer-recording is in progress.
– while Video Calibration (੬ pg. 38) is in progress.
● S-VHS ET does not work with S-VHS tapes.
● To keep the highest quality recording and playback pictures over a long period of
time, S-VHS recording on S-VHS tapes is recommended.
● Use of high grade tapes are recommended for S-VHS ET recordings.
On some tapes, picture quality will not improves even if the S-VHS ET function is
used. Check the recording quality before you start important recordings.
● You can play back S-VHS ET recordings on most of S-VHS VCRs and of VHS VCR
equipped with SQPB (S-VHS QUASI PLAYBACK) function. (Notice some VCRs are
not compatible with this function.)
● While playing back a tape recorded with this function on some tapes, noise may
appear. (If playback picture becomes blurred or interrupted, use a cleaning cassette.)
● During special effect playback (੬ pg. 26), noise may appear. If special effect
playback is performed frequently on a tape recorded with this function, the tape may
be damaged and picture may be deteriorated.
Returning point for Playback, Repeat Play or Series Playback can be set
to tape end or recording end. (This VCR considers 1-second unrecorded
portion as the recording end.) When the returning point is reached,
playback stops and the cassette will be automatically rewound.
Ⅵ RETURN POINT
TAPE END: Playback stops at the
end of tape.
REC END: Playback stops at the
end of the recording.
NOTE:
The setting you have made is kept in memory. Even if the VCR is unplugged or the
power failure occurs, it will resume every time you turn on the VCR. (੬ pg. 9)
When this function is set to "ON", you can record Month/Day/Year and
clock time display (੬ pg. 61) with your picture.
Ⅵ DAY/TIME INSERT
ON
NOTES:
OFF
● To use this function, be sure to set "ON SCREEN (REC)" to "ON". (੬ pg. 37, 38)
● The superimposed operational indicators on the screen will also be recorded.
● The setting you have made is kept in memory. Even if the VCR is unplugged or
the power failure occurs, it will resume every time you turn on the VCR.
(੬ pg. 9)
● This function is not available during Audio Dubbing or Insert Editing.
Usually, you can only record onto a cassette with its record safety tab
intact. When the this function is set to “OFF”, recording can be done
onto a cassette whose record safety tab is removed.
Ⅵ REC SAFETY
ON
OFF
NOTES:
● The setting you have made is kept in memory. Even if the VCR is unplugged or
the power failure occurs, it will resume every time you turn on the VCR.
(੬ pg. 9)
● When "REC SAFETY" is set to "OFF", playback does not start automatically when
you insert a cassette with its record safety tab removed. (੬ pg. 15)
When you set daily timer recording, you can use one cassette repeatedly.
If you select "AUTO REW", the VCR rewinds tape each time after timer
recording and the timer mode is engaged.
If you select "NORM", the VCR turns off after timer recording. Rewinds
the tape or replace it, and engage timer recording standby mode
manually.
Ⅵ DAILY T. RECORD
NORM
AUTO REW
Refer to page 37 for setting procedures.
Download from Www.Somanuals.com. All Manuals Search And Download.
OTHER USEFUL FUNCTIONS (cont.)
42
EN
This function allows you to automatically record a
satellite program which is timer-programed on your DBS
receiver.
Satellite Auto
Recording
Preparation: Connect a DBS receiver to the AUDIO/
VIDEO IN or S VIDEO IN (L-1) connectors* on the rear;
otherwise, you cannot use this function.
• You can also connect the cable box if it has a timer.
* To use these connectors, you have to select which one to use
(੬ pg. 40).
REC LINK lamp
Set timer program on DBS receiver
1
• For timer programing method, refer to the
manual supplied with the DBS receiver.
REW
FF
PLAY
POWER
–
+
Load a cassette
CH– /+
PUSH TURN
/
2
3
4
Make sure the record safety tab is intact.
REC LINK
A.DUB
S
VIDEO
VIDEO (MONO)L—AUDIO—R
24HR QUICK
PROGRAM
SP EP
VCR
DIGITAL BC/NR
INSERT
REC
PAUSE
STOP/EJECT
Set tape speed
Press SP/EP (
) to set the recording speed.
4
Engage Satellite Auto Recording standby
mode
Press REC LINK for more than 2 seconds.
The VCR turns off automatically and the REC
LINK lamp lights (Satellite Auto Recording
standby mode).
1
4
7
2
5
8
3
6
9
2
When signals come into the VCR from the DBS
receiver, the VCR starts recording (the REC LINK
lamp blinks), and stops recording and goes off
when signals stop coming in.
4
0
• To disengage the Satellite Auto Recording
standby mode, press REC LINK. The REC LINK
lamp goes off.
IMPORTANT: Be sure not to turn on the DBS receiver
before the program starts broadcasting; otherwise, the
VCR will start recording when the DBS receiver is
turned on.
1
3
NOTES:
● While the Satellite Auto Recording standby mode or after Satellite Auto Recording is finished, the VCR will not enter the timer
recording standby mode even though “AUTO TIMER” is set to “ON”. (੬ pg. 37, 38)
● If you turn off this VCR while Satellite Auto Recording is in progress, recording stops.
● Video Calibration (੬ pg. 38) does not work while Satellite Auto Recording is in progress.
● Auto Clock (੬ pg. 11) does not work while in the Satellite Auto Recording standby mode.
● The VCR may not record a short portion at the beginning of the program or may record slightly longer than the actual length of the
program when Satellite Auto Recording method is used.
● If you engage the Satellite Auto Recording standby mode while the DBS receiver is turned on, the VCR will not start Satellite Auto
Recording even though the REC LINK lamp blinks. When you turn off and on the DBS receiver once again, the VCR starts
recording.
● If you have connected another component other than a DBS receiver (or cable box) to the AUDIO/VIDEO IN or S VIDEO IN (L-1)
connectors, be sure not to engage the Satellite Auto Recording standby mode; otherwise, the VCR will start recording when the
connected component is turned on.
● Satellite Auto Recording and timer-recording cannot be performed at the same time.
● If the REC LINK lamp does not light but blinks quickly in the Satellite Auto Recording standby mode (even though your DBS
receiver is turned off), Satellite Auto Recording will not work properly.
If this is the case, perform “Express Timer Programing” (੬ pg. 32) to timer-record a satellite program.
(Some DBS receivers output signals even if the power is off. Satellite Auto Recording is not possible with those DBS receivers.)
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
43
You can disable the VCR operations.
● You can only use the Remote for this operation.
Child Lock
While the VCR is turned on, press and hold POWER on
the Remote for more than 10 seconds.
The VCR turns off, and “CL” appears on the front display
panel for about 5 seconds, then the clock time appears
again.
POWER
TIMER
1
4
7
2
5
8
3
6
9
● The child lock function is now activated and you
cannot turn on the VCR by pressing POWER on the
front panel.
2
4
0
To release the child lock, press and hold POWER on the
Remote until the VCR turns on.
● Pressing TIMER during timer recording, unplugging the
AC power cord or a power outage also releases the
child lock.
1
NOTES:
● When the child lock function is in use, keep the Remote out
of the children’s reach.
● Timer recording programs will be performed even if the child
lock function is activated.
● If any button on the VCR or on the Remote is pressed when
the child lock function is activated, “CL” appears on the front
display panel for about 5 seconds, then the clock time
appears again.
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING
44
EN
Edit From
Camcorder
3
REW
FF
PLAY
POWER
–
+
CH– /+
PUSH TURN
/
REC LINK
A.DUB
S
VIDEO
VIDEO (MONO)L—AUDIO—R
24HR QUICK
PROGRAM
SP EP
VCR
DIGITAL TBC/NR
INSERT
REC
PAUSE
STOP/EJECT
Connection
This VCR (for recording)
8
REW
FF
PLAY
POWER
–
+
CH– /+
PUSH TURN
/
REC LINK
A.DUB
S
VIDEO
VIDEO (MONO)L—AUDIO—R
24HR QUICK
PROGRAM
SP EP
VCR
DIGITAL TBC/NR
INSERT
REC
PAUSE
STOP/EJECT
To AUDIO/
VIDEO Input
Audio/video
cable
1
4
7
2
5
8
3
6
9
2
(supplied)
To S VIDEO
Input*
3
3
4
0
S-video cable
(supplied)
To Audio/video
output
1
8
4 –6
To S-video
output
4 5
4 5
Camcorder
(for playback)
Various connection for editing tapes
The following three methods can be used for editing tapes.
● VHS to S-VHS editing (VIDEO-VIDEO connection):
Although the picture quality is inherently limited by the
original VHS quality, the edited tape has better picture
quality than those made by VHS-to-VHS editing.
● S-VHS to VHS editing (VIDEO-VIDEO connection):
Since the original source is recorded in S-VHS mode, the
edited tape has better picture quality than those made by
VHS-to-VHS editing.
● S-VHS to S-VHS (S-VIDEO connection): Original picture
quality of S-VHS made can be duplicated with minimal
picture degradation. This is the best editing method you
can use on S-VHS VCRs.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
45
You can use a camcorder as the playback VCR and your
VCR as the recording VCR
Return to normal screen
6
7
Press MENU.
Make connections
Start playback
Set the camcorder to its play mode.
1
Connect an audio/video cable between the
camcorder’s audio/video output connectors and
your VCR’s audio/video input connectors.
NOTE:
If the camcorder is equipped with a superimpose/OSD
disable feature then set it to “OFF” before starting
playback.
● When using a camcorder with a monaural
output, connect the audio output connector on
the camcorder to the left audio input connector
on this VCR.
Start recording
On the front panel:
Press REC ( ¶ ).
On the Remote:
8
Load a cassette
2
Insert the cassette to be recorded on into this
VCR (for recording).
Press REC ( ¶ ) and PLAY ( 3 ) at the same time.
Select input mode on this VCR
3
Select “L-1” — when connecting the camcorder
NOTE:
to the audio/video input
connectors on the rear panel.
Be sure to select “AUTO” for “PICTURE CONTROL” (or
“NORM” when “VIDEO CALIBRATION” is set to “OFF”) after
you finish dubbing the tapes (੬ pg. 37 and 38).
Select “F-1” — when connecting the camcorder
to the audio/video input
connectors on the front panel.
On the front panel:
Push the JOG dial, then turn it to the left or right.
On the Remote:
Press the Number key "0 (AUX)" and/or CH +/–.
Select video input terminal
4
Follow the procedure described on pages 37 and
40.
When using S VIDEO terminal, set “FRONT AUX
INPUT” (or “REAR AUX INPUT” if you use the
connectors on the rear) to “S-VIDEO”.
When using VIDEO terminal, set “FRONT AUX
INPUT” (or “REAR AUX INPUT”) to “VIDEO”.
Select edit mode
5
Follow the procedure described on pages 37 and
38.
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING (cont.)
46
EN
Load cassettes
2
3
Edit To Or
From Another
VCR
Insert the playback cassette into the playback
VCR and the cassette to be recorded on into the
recording VCR.
Select input mode on recording VCR
Select the correct external input on the other
VCR.
● On this VCR (when using this VCR as the
recording VCR);
Select “L-1” — when connecting the other VCR
to the audio/video input connectors on
the rear panel;
Select “F-1” — when connecting the other VCR
to the audio/video input connectors on
the front panel.
Connection
Ex. When using this VCR as the playback VCR
This VCR (for playback)
REMOTE
On the front panel:
Push the JOG dial, then turn it to the left or
IN
OUT
IN
ANTENNA IN
R
L
REMOTE
OUT
AUDIO
IN
OUT
VHF/UHF
TV OUT
S
V
I
VIDEO
D
E
O
right.
On the Remote:
Press the Number key "0 (AUX)" and/or CH +/–.
To AUDIO/
VIDEO OUT
To S VIDEO
OUT
S-video cable
(supplied)
Select video input terminal on recording
VCR
When using this VCR as the recording VCR,
follow the procedure described on pages 37 and
40.
When using S VIDEO terminal, set “FRONT AUX
INPUT” (or “REAR AUX INPUT” if you use the
connectors on the rear) to “S-VIDEO”.
Audio/video
4
cable (supplied)
To S-video
Input
To Audio/
video Input
When using VIDEO terminal, set “FRONT AUX
INPUT” (or “REAR AUX INPUT”) to “VIDEO”.
Select edit mode
On this VCR, set “PICTURE CONTROL” to
“EDIT” by following the procedure described on
pages 37 and 38.
Another VCR (for recording)
5
6
You can use your VCR as the playback or recording VCR.
● Refer also to the other VCR’s instruction manual for
connection and its operations.
Start playback
Press PLAY ( 3 ) on the playback VCR.
NOTE:
Make connections
Connect an audio/video cable between the
playback VCR’s audio/video output connectors
and the recording VCR’s audio/video input
connectors.
If the playback VCR is equipped with a superimpose/
OSD disable feature then set it to “OFF” before starting
playback.
1
Start recording
Press REC ( ¶ ) on the recording VCR.
7
● When using this VCR as the recording VCR,
connect this VCR’s audio/video input
connectors to the audio/video output
connectors on the other VCR.
NOTE:
If the playback VCR is monaural, connect the
audio output connector on the playback VCR
to the left audio input connector on this VCR.
Be sure to select “AUTO” for “PICTURE CONTROL” (or
“NORM” when “VIDEO CALIBRATION” is set to “OFF”) after
you finish dubbing the tapes (੬ pg. 37 and 38).
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
47
Load a cassette and prepare the audio
source
2
3
Audio Dubbing
Select input mode
Select “F-1” — when connecting the audio
component to the audio input connectors on
the front panel.
Connection
This VCR (for recording)
Select “L-1” — when connecting the audio
component to the audio input connectors on
the rear panel.
REW
FF
PLAY
POWER
–
+
CH– /+
PUSH TURN
/
On the front panel:
REC LINK
A.DUB
S
VIDEO
VIDEO (MONO)L—AUDIO—R
24HR QUICK
PROGRAM
Push the JOG dial, then turn it to the left or right.
SP EP
VCR
DIGITAL TBC/NR
INSERT
REC
PAUSE
STOP/EJECT
On the Remote:
Press the Number key "0 (AUX)" and/or CH +/–.
To AUDIO
input
Audio cable
(not supplied)
Locate start point
4
5
1 Press PLAY ( 3 ) to start playback.
2 Press PAUSE ( 8 ) when you find the beginning
of the scene for which you want to audio-dub.
To Audio output
Activate editing mode
Press A.DUB on the front panel.
CD player
(as the audio source)
● The VCR enters the Audio Dubbing pause mode.
●
blinks,
and
light up on the front
display panel.
● Audio Dubbing is also possible using the audio
input connectors on the rear panel.
Start audio dubbing
6
Start playing the audio source and press PLAY
( 3 ) on this VCR.
●
blinks and
display panel.
is displayed on the front
You can replace sounds recorded on the normal track with
new sounds — for example, your favorite song played back
on the CD player.
● Refer also to the other audio component’s instruction
manual for connection and its operations.
To stop audio dubbing
Press STOP ( 7 ) on the Remote or STOP/EJECT ( 7 / 0 )
on the front panel.
● Audio dubbing automatically stops when the counter
reading becomes "0:00:00", and the VCR starts normal
playback.
Normal track
Before audio
dubbing
NOTES:
Video and
Hi-Fi track
● During Audio Dubbing, the sound recorded on the normal
track is selected as the monitor sound. If you want to listen to
the Hi-Fi or mixed sound (Hi-Fi sound and monaural sound),
see "Selecting monitor sound — Audio Monitor" (੬ pg. 17).
● During Audio Dubbing, the VCR status indications on TV
screen do not apear.
After audio
dubbing
● "DAY/TIME INSERT" (੬ pg. 41) is not available during Audio
Dubbing.
● Audio Dubbing cannot be performed on a tape with its record
safety tab removed. If you want to record onto a tape with its
record safety tab removed, set "REC SAFETY" to "OFF" (੬ pg.
37, 41).
● When playing back an audio-dubbed tape, select the sound
you want. See "Selecting monitor sound — Audio Monitor"
(੬ pg. 17).
Make connections
1
Connect an audio cable between the VCR’s audio
input connectors and the audio component’s
audio output connectors.
● If the audio component is monaural, connect
the AUDIO L (MONO) input connector on the
VCR.
● Picture may be distorted if you pause Audio Dubbing.
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING (cont.)
48
EN
Refer also to the other component’s instruction manual
for connection and its operations.
Insert Editing
and AV Dubbing
Insert Editing: You can replace a recorded scene with
new scene recorded on another tape or with other
material. Both the picture and the sound recorded on the
Hi-Fi sound track are replaced at the same time.
Audio/Video Dubbing: You can perform Audio Dubbing
and Insert Editing at the same time. This means that the
picture and the sounds recorded on the Hi-Fi sound
track and on the normal track are replaced at the same
time.
Connection
This VCR (for recording)
• For Audio/Video Dubbing, you can edit pictures and
sound using different sources; connect a video source
to the video input connector, and an audio source to
the audio input connectors.
REW
FF
PLAY
POWER
–
+
CH– /+
PUSH TURN
/
REC LINK
A.DUB
S
VIDEO
VIDEO (MONO)L—AUDIO—R
24HR QUICK
PROGRAM
SP EP
VCR
DIGITAL TBC/NR
INSERT
REC
PAUSE
STOP/EJECT
Insert Editing
Source tape
To AUDIO/
VIDEO input
To
S VIDEO
input
Edited tape
Before
editing
Audio/video cable
(Supplied)
S-video
cable
(Supplied)
Normal track
After
editing
To Audio/
video output
To S-video
output
Video and Hi-Fi track
AV Dubbing
Source tape
Another VCR (for playback)
Edited tape
● Insert Editing and AV Dubbing are also possible
Before
editing
using the audio/video connectors on the rear panel.
After
editing
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
49
Make connections
Connect an audio/video cable between the VCR’s
audio/video input connectors and the other
component’s audio/video output connectors.
Locate start point
1
7
8
Use REW (
) or JOG dial to reverse the tape
(See “Special Effect Playback”: ੬ pg. 26).
When you find the begining of the scene you
want to edit, press PAUSE ( 8 ).
Prepare tapes
Load the source tape on the other VCR, and the
tape to be edited on this VCR.
2
3
Activate editing mode
Press INSERT on the front panel.
● Make sure that the recording format (VHS, S-
VHS or S-VHS ET) on the VCR is the same as
that of the original recording on the tape.
Select input mode
Select “F-1” — when connecting the other
component to the audio/video input
connectors on the front panel.
● During Insert Editing pause mode (
,
and
light up on the front display panel.)
Select “L-1” — when connecting the other
component to the audio/video input
connectors on the rear panel.
● For AV Dubbing, after pressing INSERT, press
A.DUB also. During AV Dubbing insert pause
mode (
and
blink, and
lights up on
the front display panel.)
On the front panel:
Push the JOG dial, then turn it to the left or right.
Start editing
On the Remote:
Press the Number key "0 (AUX)" and/or CH +/–.
9
Press PLAY ( 3 ) on this VCR, and start playback
on the other component at the same time.
● During Insert Editing mode (
up on the front display panel.)
● During AV Dubbing mode (
on the front display panel.)
● When the counter reading becomes
“0:00:00”, editing automatically stops, and the
VCR starts normal playback.
and
light
Select video input terminal
4
Follow the procedure described on pages 37 and
40.
and
blink
When using S VIDEO terminal, set “FRONT AUX
INPUT” (or “REAR AUX INPUT” if you use the
connectors on the rear) to “S-VIDEO”.
When using VIDEO terminal, set “FRONT AUX
INPUT” (or “REAR AUX INPUT”) to “VIDEO”.
To stop editing any time during recording
Press STOP ( 7 ) on the Remote or STOP/EJECT ( 7 / 0 )
on the front panel.
Select edit mode
On this VCR, set “PICTURE CONTROL” to
“EDIT” by following the procedure described on
pages 37 and 38.
5
6
Locate end point
NOTES:
● Be sure to select “AUTO” for “PICTURE CONTROL” (or
“NORM” when “VIDEO CALIBRATION” is set to “OFF”) after
you finish editing the tapes (੬ pg. 37 and 38).
● Editing cannot be performed on a tape with its record safety
tab removed. If you want to record onto a tape with its record
safety tab removed, set "REC SAFETY" to "OFF" (੬ pg. 37,
41).
1 Press PLAY ( 3 ) to start playback.
2 Press PAUSE ( 8 ) when you find the end of
the scene for which you want to edit.
3 Press C. RESET so that the counter reading
becomes “0:00:00”.
NOTE:
● The recording speed (SP/EP) is determined by the previous
recording to be replaced. If the recording speed changes on
the tape to be edited while editing the tape, the inserted
picture will be distorted where the recording speed changes.
● When you edit a tape, a small portion of the recording
preceding to the editing start point will be erased from the
edited tape.
You can also use REW (
) or FF (
), or JOG dial
to locate the end point (See “Special Effect Playback”:
੬ pg. 26) .
● "DAY/TIME INSERT" (੬ pg. 41) is not available during Insert
Editing.
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTI-BRAND REMOTE CONTROL
50
EN
This Remote can control some functions of remote
controllable TVs of the brands listed below. Without
setting, you can control a JVC TV.
TV Brand
Setting
Turn on the TV
Turn on the TV using the Power button on the TV
or its Remote.
1
Set TV brand code
2
–2
2
Follow the example shown below.
1 Press and hold TV.
2 Press MBR SET.
2
–1 4
POWER
3 Press the Number keys to enter your TV’s
brand code by referring to the table below.
4 Press OK, and release TV.
TV
TV/VCR
1
4
7
2
5
8
3
6
9
2
The TV should turn off. If it does, try other
operations below. (੬ step 3).
2
–3
Number
● Once you have set the Remote to operate the
TV, you do not have to set it until you replace
the batteries from the Remote.
4
0
● PANASONIC has two codes. If the TV does not
function with one code, try entering the other.
1
Operate TV
3
While holding down TV, press one of the
following buttons: POWER, TV/VCR, TV CH +/–,
(TV Muting), TV VOL +/–, and Number
keys.
2
–4
ENTER
● For some brands, you must press ENTER after
having pressed the Number keys to enter a
channel number.
TV VOL +/–
TV CH +/–
NOTES:
● Depending on the type of TV, some or all functions cannot be
operated using this Remote.
● It’s not possible to operate a TV not equipped with a remote
sensor.
(Ex.) To set Remote to RCA 05:
MBRSET
A/B
TV
5
0
Release
TV BRAND NAME
JVC
BRAND CODE
01, 03
10
HITACHI
MAGNAVOX
MITSUBISHI
PANASONIC
RCA
Hold
down
Press in succession
02
03
04, 11
05
SHARP
06
SONY
07
SAMSUNG
SANYO
12
13
SEARS
13
TOSHIBA
ZENITH
08
09
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
51
This Remote can control some functions of the cable
boxes of the brands listed below. Some cable box brands
have more than one code. If your cable box does not
function with a specified code, try other codes.
Cable Box
Brand Setting
Turn on the cable box
1
Turn on the cable box using the Power button on
the cable box or its Remote.
POWER
Enter cable box brand code
2
Follow the example shown below.
2
–1 4
2
2
–2
1 Press and hold CABLE/DBS.
2 Press MBR SET.
3 Press the Number keys to enter your cable
box’s brand code by referring to the table
below.
CABLE/DBS
1
4
7
2
5
8
3
6
9
2
–3
Number
4 Press OK, and release CABLE/DBS.
The cable box should turn off. If it does, try
other operations below. (੬ step 3).
4
0
● Once you have set the Remote to operate the
cable box, you do not have to set it until you
replace the batteries from the Remote.
1
Operate cable box
3
While holding down CABLE/DBS, press one of
the following buttons: POWER, TV CH +/–, and
Number keys.
2
–4
ENTER
● For some brands, you must press ENTER after
having pressed the Number keys to enter a
channel number.
● To change the cable box’s channels, press TV
CH +/– or the Number keys. (The CH +/–
button can be used to change the VCR’s
channels only.)
TV CH +/–
CABLE BOX BRAND NAME
BRAND CODE
ARCHER
01, 05, 17
01, 17
CABLETENNA
CABLEVIEW
CITIZEN
15, 16, 17, 21, 25
NOTES:
15, 16, 17, 21, 25
● Depending on the type of cable box, some or all functions
cannot be operated using this Remote.
CURTIS
02
DIAMOND
EASTERN
01, 17
19
● It’s not possible to operate a cable box not equipped with a
remote sensor.
● It’s not possible to set the Remote for both your cable box and
a DBS receiver at the same time. You can only set the Remote
control to operate one of these units at a time.
GC BRAND
GEMINI
15, 16, 17, 21, 25
15
GENERAL INSTRUMENTS
HAMLIN
01, 04, 06, 11, 12, 15, 28
10, 18, 19, 23
JASCO
15
JERROLD
01, 04, 06, 11, 12, 15, 28
NOVAVISION
OAK
02
(Ex.) To set the Remote to RCA 14:
07
PANASONIC
PULSER
13, 14
MBRSET
CABLE/
DBS
A/B
15, 16, 17, 21, 25
13, 14
RCA
REGAL
4
1
Release
10, 18, 19, 23
19
REGENCY
REMBRANDT
SAMSUNG
SCIENTIFIC ATLANTA
SIGMA
01, 16, 17
05, 16, 24
02
Hold
down
Press in succession
07
SL MARX
05, 16, 17, 24, 25
13, 14
SPRUCER
STARGATE
TELEVIEW
TOCOM
05, 15, 16, 17, 21, 24, 25
05, 16, 24
01, 04, 16
01, 17
UNIKA
UNIVERSAL
VIDEOWAY
ZENITH
16, 17, 25
03, 09, 22
03, 09, 22
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTI-BRAND REMOTE CONTROL (cont.)
52
EN
This Remote can control some functions of the DBS
(Direct Broadcast Satellite) receivers of the brands listed
below.
DBS Receiver
Brand Setting
Turn on the DBS receiver
1
Turn on the DBS receiver using the Power button
on the DBS receiver or its Remote.
Enter DBS receiver brand code
2
Follow the example shown below.
1 Press and hold CABLE/DBS.
2 Press MBR SET.
POWER
3 Press the Number keys to enter your DBS
receiver’s brand code by referring to the table
below.
4 Press OK, and release CABLE/DBS.
The DBS receiver should turn off. If it does, try
other operations below (੬ step 3).
2
–1 4
2
2
–2
CABLE/DBS
1
4
7
2
5
8
3
6
9
2
–3
Number
● Once you have set the Remote to operate the
DBS receiver, you do not have to set it until you
replace the batteries from the Remote.
4
0
Operate DBS receiver
3
1
While holding down CABLE/DBS, press one of
the following buttons: POWER, TV CH +/–, and
Number keys.
● For some brands, you must press ENTER after
having pressed the Number keys to enter a
channel number.
● To change the DBS receiver’s channels, press
TV CH +/– or the Number keys. (The CH +/–
button can be used to change the VCR’s
channels only.)
2
–4
ENTER
TV CH +/–
NOTES:
● Depending on the type of DBS receiver, some or all functions
cannot be operated using this Remote.
● It’s not possible to operate a DBS receiver not equipped with
a remote sensor.
● It's not possible to set the Remote for both your DBS receiver
and a cable box at the same time. You can only set the
Remote to operate one of these units at a time.
DBS BRAND NAME
BRAND CODE
JVC (DISH Network)
51
51
50
41
40
(Ex.) To set the Remote to JVC 51:
ECHOSTAR (DISH Network)
PRIMESTAR
MBRSET
CABLE/
DBS
A/B
5
1
Release
SONY (DSS)
RCA (DSS)
Hold
down
Press in succession
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
53
This Remote is capable of transmitting two control
codes; one set to respond to A code control signals and
another set to respond to B code control signals.
This Remote control is preset to send A code signals
because your VCR is initially set to respond to A code
signals. You can easily modify your VCR and the Remote
to respond to B code control signals.
When using two JVC VCRs, set two VCRs and their
Remotes to different codes, so that you can operate these
VCRs separately.
Changing
Remote Control
Code
2
Set remote control code for Remote
1
1 Press and hold A/B.
2 Press the Number key “2”.
3 Press OK, and release A/B.
REW
FF
PL
POWER
–
+
● The Remote now can transmit B code control
signals.
CH– /+
PUSH TURN
/
REC LINK
A.DUB
S
VIDEO
VIDEO (MONO)L—AUDIO—R
24HR QUICK
PROGRAM
SP EP
VCR
DIGITAL TBC/NR
INSERT
REC
PAUSE
STOP/EJECT
Check remote control code for VCR
2
Press and hold PLAY ( 3 ) on the VCR for more
than 5 seconds while the VCR is turned off. The
code currently set appears on the display panel.
Change code for VCR
3
Press any key on the Remote.
● The VCR now responds to B code control
signals.
1
1
–1, 3
● To set the Remote and the VCR back to A code
control signals, repeat the same procedure as
shown above except pressing the Number key
“1” in step 2 of 1.
1
4
7
2
5
8
3
6
9
2
–2
4
To control two VCRs with the same Remote
0
You can control two JVC VCRs by switching the remote
control code for the Remote between A and B (੬ step
1), keeping two VCRs to different control codes.
● Press the Number key “1” for A code control signals
and the Number key “2” for B code control signals. (To
change only the remote control code for the Remote,
DO NOT perform steps 2 and 3 .)
1
1
–3
(Ex.) To set Remote to B code:
MBRSET
A/B
2
Release
Hold
down
Press in succession
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
54
EN
Before requesting service, use this chart and see if you can repair the trouble yourself. Small problems are often easily
corrected, and this can save you from the trouble of sending your VCR off for repair.
POWER
SYMPTOM
1. The power will not come on.
POSSIBLE CAUSE
CORRECTIVE ACTION
● The AC power cord is disconnected.
Connect the AC power cord.
● Child lock is on.
Turn off child lock function (੬ pg. 43).
2. The clock works, but the VCR’s
power will not come on.
● The VCR is in the timer recording
standby mode with “AUTO TIMER”
set to “OFF” (੬ pg. 37, 38).
Press TIMER to disengage.
● The child lock function is activated.
Press and hold POWER on the
Remote for more than 10 seconds to
release the child lock function (੬ pg.
43).
3. The Remote will not function.
● The batteries are discharged.
● Timer is on.
● Remote control A/B code is wrong.
Replace batteries.
Press TIMER button on the Remote.
Reset A/B code (੬ pg. 53).
TAPE TRANSPORT
SYMPTOM
1. The cassette gets stuck partway
during loading, and is ejected.
POSSIBLE CAUSE
● The cassette was inserted incorrectly.
CORRECTIVE ACTION
Make sure the cassette’s window is
facing up, the rear label side is facing
you and the arrow on the front of the
cassette is pointing towards the VCR.
Then insert the cassette.
PLAYBACK
SYMPTOM
1. The tape is running but the picture
will not appear.
POSSIBLE CAUSE
● If the RF connection (੬ pg. 7) is
used to view the picture, the
CORRECTIVE ACTION
Select channel 3 or 4 on the TV.
channel on the TV is set incorrectly.
● If the AV connection (੬ pg. 7) is
used to view the picture, the TV
receiver is set to the wrong mode.
Select the AV mode on the TV.
2. Breaks are noticeable in Hi-Fi
sound track.
● Automatic tracking is engaged.
Disengage auto tracking and adjust
the tracking manually (੬ pg. 17).
3. The playback picture is blurred or
interrupted, even though TV
broadcasts are clear. Or “USE
CLEANING CASSETTE” appears on
the screen.
● The video heads may be dirty.
The heads must be cleaned. Use a
dry cleaning cassette –TCL-2UX– or
consult your JVC dealer.
4. The Hi-Fi sound cannot be heard.
● Audio Monitor setting is incorrect.
Set Audio Monitor to “HI-FI”
(੬ pg. 17 or 40).
RECORDING
POSSIBLE CAUSE
SYMPTOM
1. Recording will not start.
CORRECTIVE ACTION
● There is no cassette loaded.
● "REC SAFETY" is set to "ON" and the
loaded cassette has had its record
safety tab removed.
Insert a cassette.
Set "REC SAFETY" to "OFF" (੬ pg. 37,
41).
● The VCR has been set to “L-1” or “F-
1” input mode by mistake.
2. TV broadcasts will not be recorded
properly.
Select the appropriate channel on the
VCR.
● The components have been
incorrectly connected, or correct
video connector (S VIDEO or
VIDEO) is not selected.
● The power to one or more of the
units has not been turned on.
● The recording VCR’s input mode has
been set incorrectly.
3. Tape-to-tape editing will not work.
Connect the components correctly
(੬ pg. 44 – 49) or check “REAR AUX
INPUT or “FRONT AUX INPUT”
setting (੬ pg. 37, 40).
Make sure the power to all units is on.
Select the appropriate input mode on
the recording VCR.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
55
TIMER RECORDING
SYMPTOM
1. Timer recording will not work.
POSSIBLE CAUSE
● The clock and/or the timer have
been set incorrectly.
● The timer is not engaged.
CORRECTIVE ACTION
Set the clock and/or timer correctly.
Press TIMER and make sure that ‰
appears on the front display panel.
Re-perform the set-up procedures.
Make sure you have compensated for
guide channel and VCR or cable box
channel number mismatches
(੬ pg. 30).
● The VCR has not been set up properly.
● Timer recording is in progress.
Timer programing cannot be performed
when timer recording is in progress.
Wait until it finishes.
2. Timer programing will not work.
● The timer is engaged but there is no
cassette loaded.
Load a cassette with the record safety
tab intact. If the tab is removed, set
"REC SAFETY" to "OFF". (੬ pg. 37,
41)
3. ‰ and ] on the front display
panel will not stop blinking.
● "REC SAFETY" is set to "ON" and the
loaded cassette has had its record
safety tab removed.
Set "REC SAFETY" to "OFF" (੬ pg.
37, 41) or replace the cassette with
one on which the safety tab is intact.
4. ‰ blinks for 10 seconds and the
● TIMER has been pressed when there
are no programs in memory, or the
timer recording program has not
been set correctly.
Check the programed data and set
again if necessary, then press TIMER
again.
timer mode is disengaged.
5. The power shuts off and ‰ and
● The tape reaches its end during
timer recording.
The program may not have been
recorded in its entirety. Next time be
sure you have enough time on the
tape to record the entire broadcast.
] will not stop blinking.
6. You moved, and now VCR Plus+
system does not work properly.
● The receivable stations in the new
area are received on different
channels than those in the previous
area.
Re-perform the Changing VCR Plus+
Setting procedure (੬ pg. 30).
7. “PROGRAM FULL” is displayed on
the screen.
● All 8 programs of the VCR’s timer
memory are used.
Wait until a space in memory clears,
or cancel unnecessary program
information (੬ pg. 35).
CONTINUED ON NEXT PAGE \
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING (cont.)
56
EN
OTHER PROBLEMS
CORRECTIVE ACTION
SYMPTOM
1. When scanning channels, some of
them are skipped over.
POSSIBLE CAUSE
If you need the skipped channels,
● Those channels have been preset to
restore them (੬ pg. 14).
be skipped.
Press PAUSE ( 8 ) to pause the
2. The channel cannot be changed.
● Recording is in progress.
recording, change channels, then
press PLAY ( 3 ) to resume recording.
3. The Remote will not operate your
TV or cable box or DBS receiver.
● The brand codes are set incorrectly.
Reset the correct brand codes (੬ pg.
50, 51 or 52).
Select a different host channel during
Semiauto Clock Set (੬ pg. 11), or
perform Manual Clock Set (੬ pg. 12).
4. Even though Auto or Semiauto
Clock Set has been performed, the
clock is incorrect.
● The clock setting data received from
the host channel is incorrect.
Press and hold OK on the Remote for
more than 5 seconds to deactivate
Mode Lock.
5. Buttons and controls do not
function at all.
● Mode Lock is activated.
MOISTURE CONDENSATION
Moisture in the air will condense on the VCR when you move it from a cold place to a warm place, or under
extremely humid conditions—just as water droplets form on the surface of a glass filled with cold liquid. Moisture
condensation on the head drum will cause damage to the tape. In conditions where condensation may occur, keep the
VCR turned on for a few hours to evaporate the moisture before inserting a tape.
ATTENTION
This VCR contains microcomputers. External electronic noise or interference can cause microcomputer to malfunction. If the
VCR does not operate correctly switch its power off and unplug the AC power cord from the AC supply. Wait for a while and
then plug the power cord back in. Eject and check the condition of the cassette. If everything appears normal, you can operate
the VCR as usual.
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
57
Questions and answers
RECORDING
PLAYBACK
Q. When I pause and then resume a recording, the end
of the recording before the pause is overlapped by
the new recording. Why does this happen?
Q. What happens if the tape reaches its end during
playback or search?
A. The VCR automatically rewinds it to the beginning.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A. This is normal. It reduces distortion at the pause and
Q. Can the VCR indefinitely remain in still mode?
A. No. It stops automatically after 5 minutes to protect
resume points.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Q. Can the VCR indefinitely remain in the recording
pause mode?
A. No. The VCR automatically stops after 5 minutes to
the heads.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Q. During picture search, still picture playback and
frame-by-frame playback, the picture is
protect the heads.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
intermittent. What’s the cause?
Q. What happens if the tape reaches its end during
recording?
A. The VCR automatically rewinds it to the beginning.
A. Picture loss occurs when these types of playback are
attempted with a tape recorded in LP mode. Pressing
PLAY ( 3 ) to return to normal playback will restore
the picture.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIMER RECORDING
Q. When returning from variable-speed picture search
to normal playback, the picture is disturbed. Should
I be concerned about this?
Q. REC and ‰ remain lit on the front display panel. Is
there a problem?
A. No. This is a normal condition for a timer recording
A. No, it is normal.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
in progress.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Q. When playing back programs that have been timer-
recorded consecutively (such one program from
8:00 to 9:00 and another one from 9:00 to 10:00),
the picture and sound become momentarily
Q. Can I program the timer while I’m watching a tape
or a TV broadcast?
A. Yes, but while you are setting the timer you will not
see the tape’s or broadcast program’s picture as it is
replaced by the on-screen menu. (The sound from
the tape or broadcast program will be heard during
the timer setting.)
distorted where the first program ends and the
second program begins. Is this a malfunction?
A. No. This is normal.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Q. Other than preventing further recording, what
effect does removing the safety tab have?
A. It disables marking of index codes.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Q. Sometimes, during index search, the VCR cannot
find the program I want to see. Why not?
A. There may be index codes too close together.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Q. During playback, on-screen display sometimes
jitters. Why does this happen?
A. If the condition of the tape being played back is not
good, jittering of the video (including on-screen
display) may occur.
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
58
EN
List of terms
This guide serves as a quick way to locate frequently used terms and on-screen display names.
A
M
T
Accidental erasure prevention 20
AUDIO MONITOR 40
Audio Monitor 17
Manual tracking 17
Tape speed 19, 42
Time counter 16, 20
Time zone selection 11
Timer recording
Canceling 35
Changing 35
Checking 35
Mode lock 15, 16, 20, 21, 23, 25
Multi-Brand Remote
Setting cable box brand 51
Setting DBS receiver brand 52
Setting TV brand 50
Auto Daylight Saving Time 11
AUTO SP = EP TIMER 39
AUTO TIMER 38
Automatic tracking 17
N
Express 32
Guide channel setting 30
VCR Plus+ 28
B
Next Function Memory 17
Basic connections
AV connection 6
RF connection 6
S-video connection 6
O
Timer warning display 34
Tracking 17
Troubleshooting 54
ON SCREEN (PLAY) 39
ON SCREEN (REC) 38
On-screen display 21
Tuner setting
C
Adding channels 14
Auto Channel Set 13
Deleting channels 14
Manual Channel Set 14
P
Channel No. indication 20
Clock setting 10
Manual setting 12
Preparation 10
Semiauto setting 11
Clock time 16, 20
Contents 5
PBS channel 8
PICTURE CONTROL 38
Playback 15
Playback Resume Function 18
Plug & Play 8
V
VCR Plus+ timer programing 28
VIDEO CALIBRATION 38
VIDEO STABILIZER 39
R
Counter reset 16, 20
REAR AUX INPUT 40
REC SAFETY 41
Recording 19
D
24H quick programing 34
2ND AUDIO RECORD 39
DAILY T. RECORD 41
DAY/TIME INSERT 41
DIGITAL R3 39
Digital TBC/NR 18
Recording Resume Function 21
Repeat Play 16
Repeat Recording 20
RETURN POINT 41
E
S
Editing
S-VHS ET 41
From a camcorder 44
From another VCR 46
To another VCR 46
Express timer programing 32
S-VHS MODE 40
Satellite Auto Recording 42
Series Playback 22
Series Recording 24
Special effect playback
Frame-by-Frame Playback 27
High-Speed Picture Search 26
How to use the JOG dial 26
How to use the SHUTTLE PLUS
buttons 27
F
FRONT AUX INPUT 40
Function Set screen 37
G
Guide channel 30
Picture Search 26
Skip Search 27
Slow Motion Playback 27
Still Picture Playback 27
Variable-Speed Picture Search 26
Specifications 63
H
Host channel 8
I
Index Search 17
Instant Review 18
L
Last-Function Memory 9
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
59
Front panel
1
2
9
3
4
FF
REW
PLAY
POWER
–
+
CH – /+
PUSH / TURN
REC LINK
A.DUB
S VIDEO
VIDEO (MONO)L—AUDIO—R
24HR QUICK
PROGRAM
SP EP
VCR
DIGITAL TBC/NR
INSERT
REC
PAUSE
STOP/EJECT
5
6
7
8
! @ # $ % ^
0
1 POWER button : ੬ pg. 15, 19
2 Cassette loading slot
3 PLAY ( # ) button : ੬ pg. 15
4 Advanced JOG dial : ੬ pg. 15, 19, 26
9 Front display panel : ੬ pg. 60
0 Remote sensor
! INSERT button : ੬ pg. 49
@ A.DUB button : ੬ pg. 47
5 S VIDEO input connector : ੬ pg. 44, 48
# 24HR QUICK PROGRAM button : ੬ pg. 34
$ REC ( ¶ ) button : ੬ pg. 19, 20
6 AUDIO/VIDEO input connectors : ੬ pg. 47, 48
7 DIGITAL TBC/NR button and lamp: ੬ pg. 18
8 REC LINK button and lamp : ੬ pg. 42
% PAUSE ( 8 ) button : ੬ pg. 19, 27
^ STOP/EJECT ( 7 / 0 ) button : ੬ pg. 15, 19
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX (cont.)
60
EN
Front display panel
1
5
2
3 4
8
SP
VCR
6
7
9
1 Symbolic Mode Indicators
2 Tape speed indicators
3 Program start time and stop time indicator :
੬ pg. 34
STILL:
SLOW:
PLAY:
FF/REW VARIABLE
SHUTTLE SEARCH:
Mode Lock indicators : ੬ pg. 15, 16, 20, 21,
23, 25
RECORD:
RECORD PAUSE:
4 Timer mode indicator : ੬ pg. 29, 33
5 Tape remaining time indicator : ੬ pg. 16, 20
6 S-VHS indicator : ੬ pg. 15, 41
7 VCR mode indicator : ੬ pg. 19, 20
8 Cassette mark
AUDIO DUBBING:
AUDIO DUBBING PAUSE:
INSERT:
9 Channel and auxiliary input (“L-1” and “F-1”)
Counter reading : ੬ pg. 16, 20
Clock time : ੬ pg. 16, 20
INSERT PAUSE:
AUDIO DUBBING INSERT:
AUDIO DUBBING INSERT PAUSE:
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
61
Rear panel
4
1
2
3
REMOTE
IN
IN
OUT
ANTENNA IN
R
L
REMOTE
OUT
AUDIO
VIDEO
IN
OUT
VHF/UHF
TV OUT
S
V
I
D
E
O
5
6 7
8 9 0
1 AC power cord : ੬ pg. 6
2REMOTE OUT terminal :
੬ pg. 22, 24
3 REMOTE IN terminal : ੬ pg. 22, 24
*For the Remote Control Unit RM-G30
(not supplied).
5 Lithium battery compartment: ੬ pg. 7
6 S VIDEO IN connector : ੬ pg. 48
7 S VIDEO OUT connector : ੬ pg. 6
8 AUDIO/VIDEO IN connectors : ੬ pg. 48
9 AUDIO/VIDEO OUT connectors : ੬ pg. 46
0 TV OUT terminal : ੬ pg. 6
4 ANTENNA IN terminal : ੬ pg. 6
On-screen display
7
1
2
3
4
5
CH 125
FRI 12:00:00 AM
11/30/01 – WARNING–
STEREO TIMER RECORDING
RECORD
8
PAUSE
SP
9
0
SAP
TO START SOON
(CANCEL)
!
B - - - - - + - - - - - + - - - - - + - - - - - E
INDEX 1
@
#
$
NORM
HI–FI
REMAIN
COUNT
10:00
–1:23:45
6
1 Channel and auxiliary input (“L-1” and “F-1”)
2 Day and clock time
3 Month/Day/Year
8 VCR operation mode indication
9 Tape speed indication
0 Cassette indication
4 STEREO program indication : ੬ pg. 21
5 SAP (Second Audio Program) indication :
੬ pg. 21
6 Audio monitor indications : ੬ pg. 17, 40
7 Timer warning display : ੬ pg. 34
! Tape position indicator : ੬ pg. 16
@ Index no. indication : ੬ pg. 17
# Tape remaining time : ੬ pg. 16, 20
$ Time counter : ੬ pg. 16, 20
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX (cont.)
62
EN
1 CABLE/DBS button : ੬ pg. 51, 52
Remote
2 TV button: ੬ pg. 50
&
*
(
)
q
w
e
r
t
y
u
i
o
p
Q
W
3 TV/VCR button : ੬ pg. 19, 21, 50
4 REVIEW button : ੬ pg. 18
5 Number buttons : ੬ pg. 19, 28, 31
6 DBS button (No function)
7 CANCEL button : ੬ pg. 29, 35
C. (Counter) RESET button : ੬ pg. 16, 20
8 STOP +/– button : ੬ pg. 29, 32
9 START +/– button : ੬ pg. 32
0 PROG. (Program) button : ੬ pg. 28, 32
! PROG. CHECK button : ੬ pg. 35
1
2
3
4
MBRSET
A/B
CABLE/
DBS
TV
POWER
TV/VCR A. MONITOR DISPLAY
1
2
3
5
2
4
5
6
DBS
DAILY
WEEKLY
6
7
8
7
C. RESET
8
9
AUX
CANCEL
TIMER
4
0
@ REW (
1 ) button : ੬ pg. 15, 19, 26
# REC ( ¶ ) button : ੬ pg. 19, 20
$ STOP ( 7 ) button : ੬ pg. 15, 16
% MENU button : ੬ pg. 37
START
STOP
DATE
CH
9
EXPRESS PROGRAMMING
0
!
@
#
$
%
^
PROG
CHECK
SP/EP
SKIP SEARCH
PROG
1
^ SHUTTLE PLUS %fi buttons
TV CH +/– buttons : ੬ pg. 50, 51, 52
& MBR SET button : ੬ pg. 50, 51, 52
A/B button : ੬ pg. 53
* POWER button : ੬ pg. 17, 19
( A. (Audio) MONITOR button : ੬ pg. 17
(TV Muting) button : ੬ pg. 50
PLAY
STOP
C
+
SHUTTLE
PLUS
) DISPLAY button : ੬ pg. 16, 20
q DAILY button : ੬ pg. 29, 33
w WEEKLY button : ੬ pg. 29, 33
e AUX button : ੬ pg. 45, 46, 47, 49
r TIMER button : ੬ pg. 29, 33, 35
t DATE +/– button : ੬ pg. 32
y CH +/– button : ੬ pg. 19, 32
u SKIP SEARCH button : ੬ pg. 27
i SP/EP button : ੬ pg. 19, 29, 33
o PLAY ( 3 ) button: ੬ pg. 15, 19
E
MULTI BRAND
REMOTE CONTROL UNIT
p FF (
¡ ) button: ੬ pg. 15, 19, 26
The glow-in-the-dark buttons shown in white on the
illustration above are helpful when using the
Remote in darkened rooms.
Q PAUSE ( 8 ) button: ੬ pg. 19, 27
W OK button
ENTER button : ੬ pg. 50, 51, 52
OSD button : ੬ pg. 21
Buttons with a small dot on the left side of the name
can also be used to operate your TV while holding
down TV on the Remote. (੬ pg. 50).
E SHUTTLE PLUS 4 ¢ (@ #) button
: ੬ pg. 27
TV VOL +/– button : ੬ pg. 50
How to use the Remote
Before use, insert two AA size batteries into the Remote with the polarity (ª and ·) matched correctly as
indicated on the battery compartment or on the lid.
The Remote can operate most of your VCR’s functions, as well as basic functions of TV sets, cable boxes and DBS
receivers.
● Point the Remote toward the remote sensor on the target component.
● The maximum operating distance of the remote control is about 8 m.
NOTE:
If the Remote does not work properly, remove its batteries, wait for a few seconds, replace the batteries and then try again.
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
EN
63
GENERAL
TIMER
Power requirement
Power consumption
Power on
: AC 120 V` , 60 Hz
Clock reference
Program capacity
: Quartz
: 1-year programmable timer/
8 programs
: 20 W
: 2.5 W
Power off
Memory backup time
: Approx. 6 months
Temperature
Operating
Storage
Operating position
Estimated figure based on
supplied fresh battery; actual
performance may differ.
: 5°C to 40°C (41°F to 104°F)
: –20°C to 60°C (–4°F to140°F)
: Horizontal only
Dimensions (W x H x D) : 400 mm x 94 mm x 283 mm
ACCESSORIES
Weight
: 3.4 kg
Format
Maximum recording time
SP
: S-VHS/VHS NTSC standard
Provided accessories
: Infrared remote control unit,
“AA” battery x 2,
Lithium battery CR2025,
S-video cable (4-pin),
RF cable (F-type),
: 210 min. with ST-210 video
cassette
: 630 min. with ST-210 video
cassette
EP
Audio/video cable,
BNC/RCA adapter x 2
VIDEO/AUDIO
Specifications shown are for SP mode unless specified
otherwise.
E. & O.E. Design and specifications subject to change without
notice.
Signal system
: NTSC-type color signal and
EIA monochrome signal,
525 lines/60 fields
Recording/
Playback system
: DA-4 (Double Azimuth) head
helical scan system
: 45 dB
Usable cassettes
Full-Size VHS
T-30 (ST-30**)
T-60 (ST-60**)
T-90
Signal-to-noise ratio
Horizontal resolution
VHS
: 230 lines
: 400 lines
S-VHS
T-120 (ST-120**)
T-160 (ST-160**)
ST-210**
Frequency range
Normal audio
Hi-Fi audio
: 70 Hz to 10,000 Hz
: 20 Hz to 20,000 Hz
: RCA connectors
(IN x 2, OUT x 1)
S-video connectors
(IN x 2, OUT x 1)
Input/Output
Compact VHS*
TC-20 (ST-C20**)
TC-30 (ST-C30**)
TC-40 (ST-C40**)
* Compact VHS camcorder recordings can be
played on this video recorder. Simply place the
recorded cassette into a VHS Cassette Adapter
and it can be used just like any full-sized VHS
cassette.
** This VCR can record on regular VHS and Super
VHS cassettes. While only VHS signals can be
recorded on regular VHS cassettes 1), both VHS
and Super VHS signals can be recorded and
played back using Super VHS cassettes.
TUNER
Tuning system
Channel coverage
VHF
UHF
CATV
RF output
: Frequency-synthesized tuner
: Channels 2–13
: Channels 14–69
: 113 Channels
: Channel 3 or 4 (switchable;
preset to Channel 3 when
shipped) 75 ohms,
unbalanced
1)
By using the S-VHS ET function, it is possible to record and
play back with S-VHS picture quality on VHS cassettes on
this VCR.
Download from Www.Somanuals.com. All Manuals Search And Download.
VICTOR COMPANY OF JAPAN, LIMITED
Printed in Malaysia
1001 MNV*ID*PJ
U
COPYRIGHT © 2001 VICTOR COMPANY OF JAPAN, LTD.
Download from Www.Somanuals.com. All Manuals Search And Download.
|