JVC DVD VCR Combo HR XVC39SU User Manual

DVD PLAYER &

VIDEO CASSETTE RECORDER

HR-XVC38BU

HR-XVC39SU

For Customer Use:

Enter below the Model No. and

Serial No. which are located on the

rear of cabinet. Retain this

information for future reference.

INSTRUCTIONS

Model No.

Serial No.

LPT1128-001A

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY INSTRUCTIONS

CAUTION:

PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNER’S MANUAL. AND

THOSE MARKED ON THE PRODUCT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE.

This product has been designed and manufactured to assure personal safety. Improper use can result in electric shock or fire

hazard. The safeguards incorporated in this product will protect you if you observe the following procedures for installation,

use, and servicing.

This product does not contain any parts that can be repaired by the user.

DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER SERVICING

TO QUALIFIED SERVICE PERSONNEL ONLY.

1. Read these instructions. - All these safety and operat-

ing instructions should be read before the product is

operated.

10. Protect the power cord from being walked on or

pinched particularly at plugs, convenience recepta-

cles, and the point where they exit from the product.

2. Keep these instructions. - The safety, operating and

11. Only use attachments/accessories specified by the

manufacturer.

use instructions should be retained for future reference.

3. Heed all warnings. - All warnings on the product and in

the operating instructions should be adhered to.

4. Follow all instructions. - All operating and use instruc-

tions should be followed.

5. Do not use this product near water. – For example:

near a bath tub, wash bowl, kitchen sink, laundry tub,

in a wet basement; or near a swimming pool; and other

areas located near water.

12. Use only with the cart, stand, tripod, bracket, or table

specified by the manufacturer, or sold with appara-

tus. When a cart is used, use caution when moving

the cart/product combination to avoid injury from

tip-over.

6. Clean only with dry cloth. – Unplug this product from

the wall outlet before cleaning. Do not use liquid clean-

ers.

7. Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

13. Unplug this product during lightning storms or when

unused for long periods of time.

Slots and openings in the cabinet are provided for ven-

tilation and to ensure reliable operation of the product

and to protect it from over- heating. The openings should

never be blocked by placing the product on a bed, sofa,

rug or other similar surface. This product should not be

placed in a built-in installation such as a bookcase or

rack unless proper ventilation is provided or the manu-

facturer’s instructions have been adhered to.

14. Refer all servicing to qualified service personnel.

Servicing is required when the product has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into the product, the product has been

exposed to rain or moisture, does not operate nor-

mally, or has been dropped.

8. Do not install near any heat sources such as

radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety.

If the provided plug does not fit into your outlet, con-

sult an electrician for replacement of the obsolete

outlet.

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

Introduction . . . . . . . . . . . . . . . . . . . . . .5-9

Operations - VCR. . . . . . . . . . . . . . . .19-25

Moisture Condensation. . . . . . . . . . . . . . . . . . 5

Symbol Used in this Manual . . . . . . . . . . . . . 5

VCR Tape Playback . . . . . . . . . . . . . . . . . . 19-20

Basic Instructions. . . . . . . . . . . . . . . . . . . . . . 19

Auto Tracking . . . . . . . . . . . . . . . . . . . . . . . . . 19

Manual Tracking . . . . . . . . . . . . . . . . . . . . . . . 19

Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Still Picture and Frame-by-Frame Playback . . 19

Slow Motion . . . . . . . . . . . . . . . . . . . . . . . . . . 20

CM SKIP (Commercial Skip) . . . . . . . . . . . . . 20

VHS Hi-Fi Stereo/MTS Broadcast . . . . . . . . . 20

About the

Symbol Display . . . . . . . . . . . . 5

Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . . 5

About the Remote Control . . . . . . . . . . . . . . . 5

Types of Playable Discs . . . . . . . . . . . . . . . . . 6

Regional Code . . . . . . . . . . . . . . . . . . . . . . . . 6

Selecting the Viewing Source. . . . . . . . . . . . . 6

Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Remote Control . . . . . . . . . . . . . . . . . . . . . . . . 8

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Hi-Fi Stereo Audio Sound . . . . . . . . . . . . . . . 20

MTS (Multi-Channel TV Sound) . . . . . . . . . . . 20

VCR Tape Recording . . . . . . . . . . . . . . . . 21-24

Basic Instructions. . . . . . . . . . . . . . . . . . . . . . 21

Timer Recording . . . . . . . . . . . . . . . . . . . 21-22

Instant Timer Recording . . . . . . . . . . . . . . . . 23

Recording from External Components . . . . . 23

Copying from DVD to VCR . . . . . . . . . . . . . . 24

On-Screen Display - VCR . . . . . . . . . . . . . . . . 24

Preparation. . . . . . . . . . . . . . . . . . . . . 9-18

Connecting an Antenna or Cable TV . . . . . . 10

Basic TV Connections . . . . . . . . . . . . . . .10-11

Optional TV Connections . . . . . . . . . . . . . . . 11

Resolution Setting. . . . . . . . . . . . . . . . . . . . . 11

HDMI Connection (DVD deck only) . . . . . . . 12

Connection to an Amplifier. . . . . . . . . . . . . . 13

Initial Settings - VCR . . . . . . . . . . . . . . . . .14-15

Additional VCR Information . . . . . . . . . . . . . . 25

VCR Auto Play System . . . . . . . . . . . . . . . . . 25

S-VHS Quasi Playback (SQPB). . . . . . . . . . . 25

Easy Information . . . . . . . . . . . . . . . . . . . . . . 25

General Operation . . . . . . . . . . . . . . . . . . . . 14

CLOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

• Auto Clock Set . . . . . . . . . . . . . . . . . . . . . 14

• Manual Clock Set. . . . . . . . . . . . . . . . . . . 14

PROGRAM . . . . . . . . . . . . . . . . . . . . . . . . . 14

TUNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

• Auto Channel Programming . . . . . . . . . . 15

• To Add or Erase Channels . . . . . . . . . . . 15

SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

• FUNCTION OSD . . . . . . . . . . . . . . . . . . 15

• AUDIO MODE . . . . . . . . . . . . . . . . . . . . . 15

• BROADCAST TYPE

Operations - DVD. . . . . . . . . . . . . . . .26-30

Playback Setup . . . . . . . . . . . . . . . . . . . . . . . . 26

General Features . . . . . . . . . . . . . . . . . . . 26-27

Additional Features . . . . . . . . . . . . . . . . . 27-28

Playing an Audio CD . . . . . . . . . . . . . . . . . . . 28

Programmed Playback . . . . . . . . . . . . . . . . . 28

Viewing a JPEG File . . . . . . . . . . . . . . . . . . . . 29

Playing a DVD VR Format Disc. . . . . . . . . . . . 30

Maintenance and Service . . . . . . . . . . . . . . . . 30

(STEREO/SAP/MONO) . . . . . . . . . . . . . 15

• AUDIO OUTPUT

(STEREO/LEFT/RIGHT) . . . . . . . . . . . . . 15

Displaying Disc Information on-screen. . . . 16

Reference . . . . . . . . . . . . . . . . . . . . . .31-35

Language Codes List . . . . . . . . . . . . . . . . . . . 31

Area Codes List . . . . . . . . . . . . . . . . . . . . . . . . 31

Troubleshooting . . . . . . . . . . . . . . . . . . . . 32-33

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 34

Warranty (Only in U.S.A.) . . . . . . . . . . . . . . . . 35

Initial Settings - DVD . . . . . . . . . . . . . . . . .16-18

General Operation . . . . . . . . . . . . . . . . . . . . 16

LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . . . 17

DISPLAY. . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

AUDIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

OTHERS . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Remote Control Function . . . . . . . . . . . . . . . 18

Download from Www.Somanuals.com. All Manuals Search And Download.

Introduction

To ensure proper use of this product, please read this

owner’s manual carefully and retain for future refer-

ence.

Storing Discs

After playing, store the disc in its case. Do not expose

the disc to direct sunlight or sources of heat and never

leave it in a parked car exposed to direct sunlight.

This manual provides information on the operation

and maintenance of your DVD+VCR. Should the unit

require service, contact an authorized service loca-

tion.

Cleaning Discs

Fingerprints and dust on the disc can cause poor

picture quality and sound distortion. Before playing,

clean the disc with a clean cloth. Wipe the disc from

the center out.

Moisture Condensation

Never operate the DVD+VCR immediately after mov-

ing it from a cold location to a warm location. Leave it

for two or three hours without operating it. If you use

the DVD+VCR in such a situation, it may damage

disc/tapes and internal parts.

Symbol Used in this Manual

Do not use strong solvents such as alcohol, benzene,

thinner, commercially available cleaners, or anti-static

spray intended for older vinyl records.

Note:

Indicates special notes and operating

features.

Tip:

Indicates tips and hints for making the task

easier.

About the Remote Control

Operation Range

A section whose title has one of the following symbols

is applicable only to the disc represented by the sym-

bol.

Point the remote control at the remote sensor and

press the buttons.

ALL

All discs listed below

DVD

Distance: About 23 ft (7 m) from the front of the

DVD and finalized DVD±R/RW

remote sensor.

About 30° in each direction of the front of the

remote sensor.

VCD

Video CDs

Angle:

ACD

Audio CDs

Battery installation

Detach the battery cover on the rear of the

About the Symbol Display

remote control, and insert two (R03/AAA)

size batteries with F and G aligned cor-

rectly.

“

” may appear on your TV display during operation

and indicates that the function is not permitted by this

unit or the disc.

Do not mix old and new batteries and never

mix different types of batteries such as stan-

dard, alkaline, etc.

Notes on Discs

Handling Discs

Do not touch the playback side of the disc. Hold the

disc by the edges so that fingerprints do not get on

the surface. Never stick paper or tape on the disc.

Download from Www.Somanuals.com. All Manuals Search And Download.

Notes on Copyrights:

Types of Playable Discs

It is forbidden by law to copy, broadcast, show, broad-

cast via cable, play in public, or rent copyrighted

material without permission.

DVD

(8 cm / 12 cm disc)

Audio CD and Video CD

(8 cm / 12 cm disc)

This product features the copy protection function

developed by Macrovision. Copy protection signals

are recorded on some discs. When recording and

playing the pictures of these discs picture noise will

appear. This product incorporates copyright protec-

tion technology that is protected by method claims of

certain U.S. patents and other intellectual property

rights owned by Macrovision Corporation and other

rights owners. Use of this copyright protection technol-

ogy must be authorized by Macrovision Corporation,

and is intended for home and other limited viewing

uses only unless otherwise authorized by Macrovision

Corporation. Reverse engineering or disassembly is

prohibited.

In addition, this unit plays DVD-R, DVD+R, DVD-RW,

DVD+RW, SVCD, and CD-R / CD-RW that contains

audio titles, and/or JPEG files.

This indicates a product feature that is

capable of playing DVD-RW discs recorded

with Video Recording format.

Notes:

• Depending on the conditions of the recording equip-

ment or the CD-R/RW (or DVD±R/RW) disc itself,

some CD-R/RW (or DVD±R/RW) discs cannot be

played on the unit.

Notice for Progressive Scan Use

• Only plays if DVD-RW is recorded in Video mode

and has been finalized.

CONSUMERS SHOULD NOTE THAT NOT ALL

HIGH DEFINITION TELEVISION SETS ARE FULLY

COMPATIBLE WITH THIS PRODUCT AND MAY

CAUSE ARTIFACTS TO BE DISPLAYED IN THE

PICTURE. IN CASE OF 525 PROGRESSIVE SCAN

PICTURE PROBLEMS, IT IS RECOMMENDED

THAT THE USER SWITCH THE CONNECTION

TO THE ‘STANDARD DEFINITION’ OUTPUT. IF

THERE ARE QUESTIONS REGARDING OUR TV

SET COMPATIBILITY WITH THIS MODEL 525p

DVD+VCR, PLEASE CONTACT OUR CUSTOMER

SERVICE CENTER.

• Do not use irregularly shaped CDs (e.g., heart-

shaped or octagonal) since they may result in mal-

functions.

• This DVD+VCR requires discs and recordings to

meet certain technical standards in order to achieve

optimal playback quality. Pre-recorded DVDs are

automatically set to these standards. There are

many different types of recordable disc formats and

these require certain pre-existing conditions (see

above) to ensure compatible playback.

Regional Code

Selecting the Viewing Source

This unit has a regional code printed on the rear of

the unit. This unit can play only DVD discs labeled

same as the rear of the unit or “ALL”.

You must select one of your output sources (DVD or

VCR) to view on the TV screen.

• If you want to view DVD deck output source:

Notes on Regional Codes

• Press DVD until DVD indicator in the display

window lights and output source of DVD deck is

viewed on the TV screen.

• Most DVD discs have a globe with one or more

numbers in it clearly visible on the cover. This num-

ber must match your DVD+VCR’s regional code or

the disc cannot play.

• If you want to view VCR deck output source:

• Press VCR until VCR indicator in the display

window lights and output source of VCR deck is

viewed on the TV screen.

• If you try to play a DVD with a different region code

from your player, the message “Check Regional

Code” appears on the TV screen.

Notes:

• If you insert a disc while the DVD+VCR is in the

VCR mode, the DVD+VCR will switch to DVD mode

automatically.

• If you insert a cassette tape without prevention

tab while the DVD+VCR is in the DVD mode, the

DVD+VCR will switch to VCR mode automatically.

Download from Www.Somanuals.com. All Manuals Search And Download.

Front Panel

C D E F G H I

K L

M N O

Disc Tray (DVD deck)

DVD+VCR is in timer recording or a timer

recording is programmed. (VCR part only)

Insert a disc here.

Cassette Compartment (VCR deck)

Insert a video cassette here.

A cassette is in the VCR deck.

The VCR deck is selected.

VCR

POWER 1/:

Switches the DVD+VCR ON and OFF.

DVD+VCR is Recording. (VCR part only)

Indicates PM time. (AM is not displayed.)

Lights when TV mode is active.

REC

REW (m)

- DVD: Skip to beginning of current chapter or track,

press twice in quick successions to go to previous

chapter or track. Press and hold button for about two

seconds to search backward.

Indicates total playing time,

elapsed time, remaining time

or current deck status

- VCR: Rewinds the tape during the stop mode or for

fast reverse picture search.

(Playback, Pause, etc).

Remote Sensor

PLAY (N)

Point the DVD+VCR remote control here.

Starts playback of a disc or tape.

EJECT (Z)

Ejects the tape in the VCR deck.

FF (M)

DVD: Skip to next chapter or track. Press and hold for

two seconds for a fast forward search.

CH (-/+)

VCR: Advances the tape during the STOP mode or for

fast forward picture search.

To scan up or down through memorized channels.

REC (z)

STOP (x)

Stops playback of the disc or tape.

To record normally or to activate One-touch Timer

Recording by repeated presses.

OPEN/CLOSE (Z)

Opens or closes the disc tray.

DVD/VCR (output select)

Select one of your output sources to view on the TV

screen between DVD and VCR.

OUTPUT STATUS

You can change the resolution depending on your TV.

- HDMI mode:You can switch among the 480p, 720p

or 1080i resolution.

LINE2 (VIDEO/AUDIO (L/R))

Connect to the audio/video output of an external source

(Audio system, TV/Monitor, Another VCR).

- Component mode:You can switch among 480i,

480p, 720p or 1080i resolution.

Display Windows

The DVD deck is selected.

DVD

A disc is in the DVD deck.

(Lights when a disc is in the DVD deck

and Flashes when no disc.)

Indicates when the Progressive scan is

[P]

active.

Indicates repeat mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote Control

REW (m)/FF (M)

DVD: Search backward or forward.

- VCR: Rewinds/Advances the tape during the STOP

mode, for fast backward/forward picture search.

K 0-9

Selects numbered options in a menu.

L SUBTITLE

Selects a subtitle language.

M A.MONITOR

Selects an audio language (DVD) or an audio channel

(VCD).

N MARKER

Marks any point during playback.

O SEARCH

Displays Marker Search menu.

P REPEAT

Repeat chapter, track, title or all.

Q RANDOM

Plays tracks in random order.

Fast forwards picture search through 30 seconds of

recording.

R OPEN/CLOSE (

Opens and closes the disc tray.

EJECT (

Ejects the tape in the VCR deck.

S VCR

Select the DVD+VCR function mode to VCR.

T AUX

Selects the VCR deck’s source

(Tuner, LINE 1, or LINE 2).

U DISC MENU

Accesses menu on a DVD disc.

V ENTER/OK

Confirms menu selections.

Displays functions on the TV screen.

W RETURN (

A POWER (1/&

Switches DVD+VCR ON and OFF.

B DVD

Select the DVD+VCR function mode to DVD.

C TV/VCR

)

Removes the setup menu.

Displays the menu of a video CD with PBC.

X STOP (x)

Stops playback or recording.

Y PLAY (N)

Starts playback.

Z PROGRAM

To view channels selected by the VCR tuner or by the

TV tuner.

D DISPLAY

Places a track on the program list.

Accesses On-Screen Display.

Switches between the clock, tape counter and tape

remaining modes on the display.

a CLEAR (0000)

Removes a mark on the Marker Search menu.

E CH (-/+)

b ANGLE

Selects VCR channels.

Selects a DVD camera angle, if available.

Adjusts manually the tape’s picture onscreen.

c ZOOM

F b B v V

Enlarges DVD video image.

Selects menu options.

d REC (z)

G SETUP MENU

Starts recording. Press repeatedly to set the recording

time.

Accesses or removes DVD Setup menu and VCR menu.

H PAUSE (X)

e TITLE

Pause playback or recording temporarily. Press repeat-

edly for frame-by-frame playback.

Displays the disc’s Title menu, if available.

f REPEAT A-B

I SKIP (.

)

Repeats sequence between two points (A and B).

SPEED

Go to next chapter or track. Returns to beginning of cur-

rent chapter or track or go to previous chapter or track.

Selects recording speed.

Download from Www.Somanuals.com. All Manuals Search And Download.

Rear Panel

Caution

Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause perma-

nent damage to the unit.

B C D E

ANT.IN

COAXIAL (DIGITAL AUDIO OUT jack)

(DVD OUT)

Connect the VHF/UHF/CATV antenna to this terminal.

Connect to digital (coaxial) audio equipment.

VCR IN LINE 1 (VIDEO/AUDIO (Left/Right))

Connect the audio/video output of an external source

(Audio system, TV/Monitor, VCR, Camcorder).

S-VIDEO OUT (DVD OUT)

Connect to a S-Video Input on TV.

DVD/VCR OUT (VIDEO/AUDIO (Left/Right))

Connect to a TV with video and audio inputs.

OPTICAL (DIGITAL AUDIO OUT jack)

(DVD OUT)

Connect to digital (optical) audio equipment.

COMPONENT/PROGRESSIVE SCAN VIDEO

OUT (Y Pb Pr) (DVD OUT)

Connect to a TV with Y Pb Pr inputs.

HDMI OUT (DVD OUT)

HDMI output providing a high quality interface for digital

audio and video.

AUDIO OUT (Left/Right) (DVD OUT)

Connect to a TV or other equipment with audio inputs.

AC Power Cord

Plug into the power source.

RF. OUT

Connect to a TV with RF coaxial inputs.

Preparation

Depending on your TV and other equipment there are various ways you can connect the player. Please

refer to the manuals of your TV, VCR, stereo system or other devices as necessary for additional con-

nection information.

Notes:

• The picture and sound of a nearby TV, VCR, or radio may be distorted during playback. Position the units

away from each other or turn off the unit after removing the disc.

•

Make sure the DVD+VCR is connected directly to the TV and tune the TV to the correct video input channel.

• Do not connect the DVD+VCR’s AUDIO OUT jack to the phono in jack (record deck) of your audio system.

Do not connect the DVD+VCR via another VCR. The DVD image could be distorted by the copy protection

system.

Download from Www.Somanuals.com. All Manuals Search And Download.

To view or record a CATV channel

Connecting an Antenna or

Cable TV

1. Tune the TV to the DVD+VCR output channel

(CH 3 or 4).

Antenna:

2. Set the DVD+VCR channel selector to the cable

output channel. (Example: CH3)

Disconnect the antenna from the rear of the TV and

identify the antenna cable. If it is a round 75 ohm

coaxial cable connect it directly to the jack marked

ANT.IN on your DVD+VCR. If your antenna cable

is flat connect it to a 300-ohm to 75-ohm antenna

adaptor (not supplied) and slip the adaptor over the

ANT.IN jack. Don’t attempt to screw it into to the

DVD+VCR.

3. Select a channel using the cable converter.

Notes:

• With this connection, you cannot record one pro-

gram while viewing another.

• If you are using a cable box to tune channels, it is

not necessary to do Auto Channel Set.

Cable TV:

If your cable connection has no converter or

descrambler, unscrew the cable from your TV and

attach it to the ANT.IN jack on the DVD+VCR. If a

converter is required connect a coaxial cable from the

wall jack to the IN connector on the converter, and

a coaxial cable from the OUT connector on the con-

verter to the ANT.IN on your DVD+VCR. This cable

hookup permits both TV and DVD+VCR operation.

Basic TV Connections

Make one of the following connections, depending on

the capabilities of your TV.

RF coaxial connection

Connect the RF.OUT jack on the DVD+VCR to the

antenna in jack on the TV using the supplied 75-ohm

Coaxial Cable (R).

Antenna

How to set the DVD+VCR’s RF output

channel

1. When the DVD+VCR is turned off (standby

mode), press and hold CH (-/+) on the front panel

simultaneously for more than five seconds. “RF03”

or “RF04” appears in the display window.

2. Press CH (-/+) to change the RF output channel

(RF03 or RF04). Tune the TV to this channel.

3. Turn off the DVD+VCR.

Audio/Video connection

1. Connect the DVD/VCR VIDEO OUT jack on the

DVD+VCR to the video in jack on the TV using an

optional video cable (V).

2. Connect the Left and Right DVD/VCR AUDIO

OUT jacks on the DVD+VCR to the audio left/right

in jacks on the TV (A1) using an optional audio

cable.

Rear of DVD+VCR

Notes:

• If you use this connection, set the TV’s source

selector to VIDEO.

• For DVD/VCR VIDEO OUT jack connection,

resolution must be set to 480i or 480p, however

DVD/VCR VIDEO OUT is always at 480i standard

resolution.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connect the COMPONENT/PROGRESSIVE SCAN

VIDEO OUT jacks on the DVD+VCR to the corre-

sponding in jacks on the TV using an optional Y Pb

Pr cable (C).

Rear of TV

ANTENNA

INPUT

VIDEO

INPUT

AUDIO INPUT

Notes:

• The 480p and 720p resolutions are Progressive

scan applied resolutions.

Rear of DVD+VCR

• Progressive scan does not work with the analog

video connections (yellow VIDEO OUT jack and

S-VIDEO OUT jack).

Resolution Setting

The resolution setting support only DVD playback.

1. Before you set the resolution, this unit must be in

stop mode. Press STOP (x) to stop playback.

2. Press OUTPUT STATUS on the front panel once.

The current resolution setting will be appears in

the display window.

3. Press OUTPUT STATUS repeatedly to change the

resolution you want.

The available resolution according to the connections

are as shown below.

COMPONENT/PROGRESSIVE SCAN

VIDEO INPUT

AUDIO INPUT

S-VIDEO

INPUT

Rear of TV

OUTPUT

Available

CONNECTIONS

Resolutions

1920 x 1080i

1280 x 720p

720 x 480p

1920 x 1080i

1280 x 720p

720 x 480p

720 x 480i

HDMI

Optional TV Connections

These connections support only DVD playback. The

tuner and VCR still output through the RF.OUT (R) or

DVD/VCR OUT (A, V) jacks.

VIDEO OUT

COMPONENT

VIDEO OUT

Audio connection

Connect the Left and Right AUDIO OUT jacks of the

DVD+VCR to the audio left/right in jacks on the TV

using an optional audio cable (A2).

VIDEO OUT

S-VIDEO

720 x 480i

S-Video connection

Notes:

Connect the S-VIDEO OUT jack on the DVD+VCR to

the S-Video in jack on the TV using the optional

S-Video cable (S).

• For 720p and 1080i resolution on the component

video out, only non-copy protected discs can be

played back. If the disc is copy protected, it will

be displayed in the 480p resolution without HDMI

cable connection. With HDMI cable connection, the

picture may not be displayed properly.

Note:

For S-Video connection, resolution must be set to

480i or 480p, however S-VIDEO OUT is always at

480i standard resolution.

• If your TV does not support the resolution you have

set, the picture may not be displayed properly.

Please read TV’s owner’s manual then set the reso-

lution that your TV can accept.

Component Video / Progressive Scan

connection

If your television is a high-definition or “digital

ready” television, you may take advantage of the

DVD+VCR’s progressive scan output for the highest

video resolution possible.

Download from Www.Somanuals.com. All Manuals Search And Download.

HDMI Connection

(DVD deck only)

HDMI compatible TV

HDMI

If you have a HDMI TV or monitor, you can connect it

to this DVD+VCR using a HDMI cable.

1. Set the TV’s source to HDMI (refer to TV’s

Owner’s manual).

2. Connect the HDMI OUT jack on the unit to the

HDMI jack on a HDMI compatible TV or monitor

using an optional HDMI cable (H).

3. Press OUTPUT STATUS on the front panel

repeatedly to select the desired resolution.

Notes:

Rear of DVD+VCR

• Both PCM and Bitstream Audio out is available,

when the sample frequency is set to 48kHz in

HDMI connection.

About HDMI

HDMI (High Definition Multimedia Interface) supports

both video and audio on a single digital connection

for use with DVD players, Set-Top boxes, and other

AV devices.

• If Audio setup is set to bitstream and your TV does

not support Bitstream Audio out in HDMI connec-

tion, audio sound may not output or distorted.

• When the no sound or noisy sound are output

with HDMI connection, set the Audio option [Dolby

Digital, DTS or MPEG] in the SETUP menu to PCM

or Off.

HDMI was developed to provide the technologies of

HDCP (High-bandwidth Digital Content Protection).

HDCP is used to protect digital content transmitted

and received.

• The arrow on the cable connector body should be

face up for correct alignment with the connector on

the DVD+VCR.

HDMI has the capability to support standard,

enhanced, or high-definition video plus standard to

multi-channel surround-sound audio, HDMI features

include uncompressed digital video, a bandwidth of

up to 5 gigabytes per second, one connector (instead

of several cables and connectors), and communica-

tion between the AV source and AV devices such as

DTVs.

• If there is noise or lines on the screen, please

check the HDMI cable.

HDMI, the HDMI logo and High-Definition Multimedia

Interface are trademarks or registered trademarks of

HDMI licensing LLC.

• Not all HDCP-compatible DVI devices will work with

this unit.

• If your HDMI TV does not support HDCP, the blue

screen appears on the screen.

Tip:

When you use HDMI connection, you can change the

resolution (480p, 720p, 1080i) for the HDMI output.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connection to an Amplifier

Rear of DVD+VCR

You can only listen to DVD playback using OPTICAL

(O), COAXIAL (X) and AUDIO OUT (A2) connec-

tions. The tuner and VCR will still be heard through

the RF.OUT (R) or DVD/VCR AUDIO OUT (A1) jack.

(See page 11.)

Connecting to an amplifier equipped with two

channel analog stereo or Dolby Pro Logic II/Pro

Logic

Connect the Left and Right AUDIO OUT (or DVD/

VCR AUDIO OUT) jacks on the DVD+VCR to the

audio left and right in jacks on your amplifier, receiv-

er, or stereo system using optional audio cables (A1,

A2).

COAXIAL

OPTICAL

AUDIO INPUT

DIGITAL INPUT

Amplifier (Receiver)

Connecting to an amplifier equipped with two

channel digital stereo (PCM) or to an Audio/Video

receiver equipped with a multi-channel decoder

(Dolby Digital™, MPEG 2, or DTS)

Manufactured under license from Dolby

Laboratories. “Dolby”, “Pro Logic”, and the

double-D symbol are trademarks of Dolby

Laboratories.

1. Connect one of the DVD+VCR’s DIGITAL AUDIO

OUT jacks (OPTICAL O, COAXIAL X) to the

corresponding in jack on your amplifier. Use an

optional digital (OPTICAL O, COAXIAL X) audio

cable.

DTS and DTS Digital Out are trademarks of

Digital Theater Systems, Inc.

2. You will need to activate the DVD+VCR’s digital

output. (See “AUDIO” on page 17.)

Accessory Audio/Video (A/V) Connections

to DVD+VCR

Connect the VCR IN LINE 1 or LINE 2 jacks on

the DVD+VCR to the audio/video out jacks on your

accessory component, using the optional audio/

video cables. (Refer to page 23 for “Recording from

External Components”.)

Digital Multi-channel sound

A digital multi-channel connection provides the

best sound quality. For this you need a multi-chan-

nel Audio/Video receiver that supports one or more

of the audio formats supported by your DVD+VCR

(MPEG 2, Dolby Digital and DTS). Check the receiv-

er manual and the logos on the front of the receiver.

Caution:

Due to the DTS Licensing agreement, the digital

output will be in DTS digital out when DTS audio

stream is selected.

Notes:

• If the audio format of the digital output does not

match the capabilities of your receiver, the

receiver will produce a strong, distorted sound or

no sound at all.

• Six Channel Digital Surround Sound via digital

connection can only be obtained if your receiver is

equipped with a Digital Multi-channel decoder.

• To see the audio format of the current DVD in the

on-screen display, press A.MONITOR.

Download from Www.Somanuals.com. All Manuals Search And Download.

• AUTO CLOCK SET

Initial Settings - VCR

By using the VCR Setup menu, you can make

various adjustments to items such as clock setting,

and timer recordings.

The Auto Clock Set feature is set to ON at the fac-

tory. In the ON setting, the DVD+VCR looks for a

channel carrying XDS (Extended Data Services)

information. XDS updates the clock using the

Coordinated Universal Time.

Your DVD+VCR allows remote control adjustment of

several features.

- Use b/B to choose ON or OFF.

• DAYLIGHT SAVINGS

You can turn Daylight Savings On or Off manually.

If you choose “AUTO”, the DVD+VCR sets the clock

using the DST information broadcast in the signal

(channel).

General Operation

1. Press VCR on the remote control.

2. Press SETUP MENU and the MAIN menu will

appear.

- Use b/B to choose AUTO, ON or OFF.

• TIME ZONE

You can set your local Time Zone manually. If you

choose “AUTO”, the DVD+VCR sets the clock using

the first Coordinated Universal Time information it

finds in a broadcast signal.

- Use b/B to choose the correct time zone

(AUTO, EASTERN, CENTRAL, MOUNTAIN,

PACIFIC, ALASKA or HAWAII).

Notes:

3. Use v/V to select the desired menu, then press

• The Auto Clock feature enables the DVD+VCR to

set up the clock while the DVD+VCR is turned off.

ENTER/OK.

4. Use v/V to choose a desired option on the select-

ed Menu. Then use b/B to choose a desired set-

ting.

• There are cases where the TV station does not

send or sends wrong date and/or time information

and the DVD+VCR sets the incorrect time. If this

happens we recommend that you set the clock

manually.

5. Press SETUP MENU when finished.

Note:

Menus remain on-screen for 3 minutes.

Manual Clock Set

Use v/V/b/B to enter the necessary information.

•

MONTH : Choose the month.

DAY : Choose the date.

The day of the week will display automatically.

CLOCK

• YEAR : Choose the year.

The DVD+VCR gives you two ways to set the time

and date: the Auto Clock Feature or Manually.

• TIME : Choose the time.

Press and hold b/B to advance clock continuously.

Auto Clock Set

Notes:

• If setting the clock manually, “AUTO CLOCK SET”

must set to “OFF”. If it is set to “ON”, an incorrect

date and/or time will be entered again when the

DVD+VCR is turned off.

• The clock uses the 12-hour system. Be sure to set

AM and PM correctly.

PROGRAM

The Timer Recording function allows you to record up

to 8 programs within a period of one year. (See pages

21 - 22.)

Download from Www.Somanuals.com. All Manuals Search And Download.

TUNING

SETUP

This DVD+VCR is equipped with a frequency synthe-

sized tuner capable of receiving up to 181 channels.

These include VHF channels 2-13, UHF channels

14-69 and CATV channels 1-125.

Auto Channel Programming

FUNCTION OSD

The on-screen display can be turned on or off.

AUDIO MODE

The DVD+VCR has two separate audio playback sys-

tems, the high quality VHS Hi-Fi system and standard

NORMAL mono system. The same audio is generally

recorded on both systems. The VHS Hi-Fi system

plays on separate (left and right) channels, and the

NORMAL system plays monaural sound. The normal

track is always played so the cassette can be played

on a DVD+VCR that does not have VHS Hi-Fi.

1. Choose the SOURCE SELECT option, then use

b/B to select TUNER.

Use b/B to switch among TUNER, LINE1, and

LINE2.

2. Choose the AUTO CHANNEL SET option, then

use b/B to find channels.

• The tuner will automatically cycle through all

available channels (TV/CATV) in the area and

place them in the tuner’s memory.

BROADCAST TYPE (STEREO/SAP/MONO)

• After the AUTO CHANNEL SET is complete,

the TUNING menu will hide and return to the

TV screen automatically.

Multichannel Television Sound (MTS) carries stereo

and/or Second Audio Program (SAP) bilingual sig-

nals. Set this display to the desired position when

both MTS stereo and SAP signals are received.

When only one of the MTS signal is received, the

DVD+VCR automatically selects the corresponding

receiving mode (Stereo or SAP) regardless of the

selected position. For normal operation, the display

should be in the STEREO position. The DVD+VCR

will then record a STEREO program when available,

and record a mono program IF the program is NOT

IN STEREO. For weak STEREO and/or SAP broad-

casts, changing the display to mono may give clearer

sound.

3. Make sure the TUNING BAND is set appropriately

(TV or CATV).

• TV : If you are using a standard antenna to

receive channels.

• CATV : If you are using basic cable to receive

channels.

To Add or Erase Channels

This feature allows you to add or erase channels from

memory manually.

1. Choose the CH. ADD/DEL option, then use b/B

to select a channel to add or erase.

AUDIO OUTPUT (STEREO/LEFT/RIGHT)

2. Use ENTER/OK to add or erase the channel.

Repeat steps 1 and 2 to add or erase other

channels.

Used during playback [when AUDIO MODE (HI-FI/

NORMAL) is in HI-FI position] for selecting the audio

output signals from the AUDIO OUT terminals (L ch

and R ch), and RF.OUT. This display setting should

normally be left in the stereo position, so that when a

stereo tape is played, the stereo sound will be heard

through the left and right channels. If a mono tape is

played and the audio output is set to stereo, the same

mono sound will be heard from both left and right

channels.

3. Press SETUP MENU to return to the TV screen.

Download from Www.Somanuals.com. All Manuals Search And Download.

Displaying Disc Information

on-screen - DVD

You can display various information about the disc

loaded on-screen.

Initial Settings - DVD

By using the DVD Setup menu, you can make vari-

ous adjustments to items such as picture and sound.

You can also set a language for the subtitles and the

Setup menu, among other things. For details on each

Setup menu item, see pages 17 - 18.

1. Press DISPLAY to show various playback infor-

mation.

To display and exit the Menu:

The items displayed differ depending on the disc

type or playing status.

Press SETUP MENU to display the menu. A second

press of SETUP MENU will take you back to initial

screen.

1 / 3

1 / 12

To go to the next level:

Press B on the remote control.

To go back to the previous level:

Press b on the remote control.

0:20:09

ABC

1 ENG

1 / 1

General Operation

3D SUR

1. Press DVD on the remote control.

2. Press SETUP MENU. The Setup menu appears.

2. You can select an item by pressing v/V and

change or select the setting by pressing b/B.

3. Use v/V to select the desired option then press

B to move to the second level. The screen shows

the current setting for the selected item, as well

as alternate setting(s).

• Title (Track) – Current title (or track) number/

total number of titles (or tracks)

• Chapter – Current chapter number/total number

of chapters

4. Use v/V to select the second desired option then

press B to move to the third level.

• Time – Elapsed playing time

• Audio – Selected audio language or channel

• Subtitle – Selected subtitle

• Angle – Selected angle/total number of angles

• Sound – Selected sound mode

5. Use v/V to select the desired setting then press

ENTER/OK to confirm your selection. Some items

require additional steps.

^{6. Press SETUP MENU or PLAY (}9) to exit the

Setup menu.

Note:

If no button is pressed for a few seconds, the on-

screen display disappears.

Download from Www.Somanuals.com. All Manuals Search And Download.

LANGUAGE

AUDIO

Each DVD disc has a variety of audio output options.

Set this unit’s AUDIO options according to the type of

audio system you use.

Menu Language

Select a language for the VCR and DVD’s setup

menu and information display.

Dolby Digital / DTS / MPEG

Disc Audio / Subtitle / Menu

Select the language you prefer for the audio track

(disc audio), subtitles, and the disc menu.

Bitstream: Select “Bitstream” if you connect the

DVD+VCR’s DIGITAL AUDIO OUT jack to an

amplifier or other equipment with a Dolby Digital,

DTS or MPEG decoder.

Original: Refers to the original language in which the

disc was recorded.

PCM (for Dolby Digital / MPEG): Select when con-

nected to a two-channel digital stereo amplifier.

DVDs encoded in Dolby Digital or MPEG will be

automatically downmixed to two-channel PCM

audio.

Other: To select another language, press number

buttons then ENTER/OK to enter the corresponding

4-digit number according to the language code list in

the reference chapter (see page 32). If you enter the

wrong language code, press CLEAR (0000).

Off (for DTS): If you select “Off”, the DTS signal is

not output through the DIGITAL AUDIO OUT jack.

Off (for Disc Subtitle) : Turn off Subtitle.

Sample Freq. (Frequency)

DISPLAY

If your receiver or amplifier is NOT capable of han-

dling 96 kHz signals, select 48 kHz. When this choice

is made, this unit automatically converts any 96 kHz

signals to 48 kHz so your system can decode them.

If your receiver or amplifier is capable of handling 96

kHz signals, select 96 kHz. When this choice is made,

this unit passes each type of signal through without

any further processing.

Check the documentation for your amplifier to verify

its capabilities.

TV Aspect

4:3 : Select when a standard 4:3 TV is connected.

16:9 : Select when a 16:9 wide TV is connected.

DRC (Dynamic Range Control)

With the DVD format, you can hear a program’s

soundtrack in the most accurate and realistic pre-

sentation possible, thanks to digital audio technology.

However, you may wish to compress the dynamic

range of the audio output (the difference between the

loudest sounds and the quietest ones). This allows

you to listen to a movie at a lower volume without los-

ing clarity of sound. Set DRC to On for this effect.

Display Mode

Display Mode setting works only when the TV Aspect

mode is set to “4:3”.

Letterbox: Displays a wide picture with bands on the

upper and lower portions of the screen.

Panscan: Automatically displays the wide picture on

the entire screen and cuts off the portions that do not

Vocal

Set to On only when a multi-channel karaoke DVD is

playing. The karaoke channels on the disc mix into

normal stereo sound.

fit.

Download from Www.Somanuals.com. All Manuals Search And Download.

OTHERS

Remote Control Function

Remote Control A/B/C Code

Switching

The remote control is capable of controlling three

JVC video units independently. Each of the units

can respond to one of three codes (A, B or C). The

remote control is preset to send C code signals

because your unit is initially set to respond to C code

signals. You can easily modify your unit to respond to

A or B code signals.

PBC

Set Playback Control (PBC) to On or Off.

On: Video CDs with PBC are played according to

the PBC.

Off: Video CDs with PBC are played the same way

as Audio CDs.

1/ I

Auto Play

You can set up the DVD+VCR so a DVD disc auto-

matically starts playing whenever the DVD is inserted.

If Auto Play mode is set to On, this DVD player will

search for title that has the longest playback time and

then play back the title automatically.

ENTER

1-3

On: Auto Play function is active.

Off: Auto Play function is not active.

Note:

The Auto Play function may not work for some DVDs.

B.L.E. (Black Level Expansion)

To select the black level of playback pictures. Set your

preference and monitor’s ability.

On: Expanded grey scale. (0 IRE cut off)

Off: Standard grey scale. (7.5 IRE cut off)

• Keep pressing ENTER down during step 1.

1. Press the number key “1” for A, “2” for B or “3” for

C to change the remote control code.

2. Press 1/& on the unit to turn off the unit with no

video tape inserted.

3. Press B on the unit for over 5 seconds while the

unit is turned off. The current code appears on the

display window.

4. Press x on the remote control to change the

unit’s code. The new code currently set on the

remote control blinks on the display window for

approximately 5 seconds, and is applied to the

unit.

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual Tracking

To manually adjust the tracking use the CH (-/+) but-

tons during playback.

Operations - VCR

This chapter describes how to operate the VCR and

DVD.

Notes:

• Vertical jitter requires a very fine adjustment.

VCR Tape Playback

Press the VCR button to select the device to be oper-

ated.

• Tracking is automatically reset to normal when the

tape is ejected or the power cord is unplugged for

more than 3 seconds.

Basic Instructions

This function lets you visually search for a tape sec-

tion in either direction: forward and reverse. During the

high-speed picture search modes, the audio is muted

and horizontal lines (noise bars) appear. Also, a short

time is needed to stabilize the tape speed when re-

entering the PLAY mode so slight interference may be

observed during this time.

1. Turn on the TV.

2. Tune the TV to the DVD+VCR output channel (CH

3 or 4) or if a direct VIDEO/AUDIO

connection is made between the DVD+VCR and

the TV, set the TV’s source selector to VIDEO.

3. Insert a pre-recorded video cassette.

The

ers on automatically.

4. If the (TIMER) indicator in the display window is

indicator lights and the DVD+VCR pow-

To search:

1. Press REW (m) or FF (M) during playback.

2. To return to playback, press PLAY (N).

lit, press POWER (1/:) once.

5. If a tape without a safety tab is inserted the unit

starts playback automatically.

Note:

After 3 minutes in SEARCH mode the DVD+VCR

returns to PLAY mode to protect the tape and video

heads.

If not, press PLAY (N).

6. Press STOP (x) to stop playback. If the tape

reaches the end before you press STOP (x) the

DVD+VCR automatically stops, rewinds and ejects

the tape.

Still Picture and Frame-by-Frame Playback

1. Press PAUSE (X) during playback.

A still picture appears on the TV screen and the

audio is muted.

Note:

It is not necessary to select the tape speed for play-

back because it is automatically selected by the

DVD+VCR. Also, during playback the TV/VCR selector

switches to VCR mode automatically.

2. If the still picture vibrates vertically, stabilize it by

using CH (-/+) on the remote control.

3. Press PAUSE (X) repeatedly to advance the video

picture one frame at a time.

Auto Tracking

4. To return to playback, press PLAY (N).

Automatic tracking adjusts the picture to remove snow

or streaks and beings when:

Note:

After 5 minutes in STILL mode the DVD+VCR stops to

protect the tape and video heads.

• A tape is played for the first time.

• The tape speed (SP, LP, SLP) changes.

• Streaks or snow appear due to scratches on the

tape.

Download from Www.Somanuals.com. All Manuals Search And Download.

Slow Motion

1. While in still mode, press FF (M). The tape is

played at a speed 1/19 times slower than the nor-

mal speed.

2. Use CH (-/+) on the Remote Control if

necessary to adjust the tracking.

3. To return to the normal speed, press

2. Set the AUDIO OUTPUT option to STEREO so

that the left channel sound (L) is heard from the

left speaker and the right channel sound (R) is

heard from the right speaker.

PLAY (N).

Notes:

• During slow motion, audio is muted and horizontal

lines (noise bars) may appear on the TV screen. This

is normal.

• After 3 minutes in SLOW MOTION mode the

DVD+VCR goes back to PLAY mode to protect the

tape and video heads.

CM SKIP (Commercial Skip)

This feature is useful for skipping commercials or

short program segments.

The other options are (LEFT) POSITION, which

results in the left channel sound (L) being heard

from both speakers or (RIGHT) POSITION, which

results in the right channel sound (R) being heard

from both speakers.

1. Press v in playback mode.

The DVD+VCR performs a fast forward picture

search through 30 seconds of recording.

3. Insert a cassette and press PLAY (N).

2. Press v again to extend the search time by an

addition 30 seconds. The maximum search time is

3 minutes.

MTS (Multi-Channel TV Sound)

This DVD+VCR can decode MTS stereo and bilingual

(SAP) off-the-air broadcast sound signals. It also

decodes stereo TV sound from local cable companies

as long as they operate on assigned cable frequen-

cies and use the EIA-recommended MTS stereo/bilin-

gual TV sound system.

3. When the search is complete, the DVD+VCR goes

into playback mode automatically.

VHS Hi-Fi Stereo/

MTS Broadcast

Multichannel TV Sound Indicator (MTS)

When you press ENTER/OK one or both of the indi-

cators appears on the TV Screen.

This DVD+VCR is equipped with the VHS Hi-Fi audio

sound system for recording and playback. The infor-

mation below gives a brief description of Hi-Fi audio

and how to record and play a tape in the Hi-Fi audio

mode.

STEREO

The DVD+VCR can record in stereo onto the VHS

Hi-Fi audio tracks when the BROADCAST TYPE

option is in the STEREO position. The DVD+VCR can

also record mono audio onto the mono audio track.

Hi-Fi Stereo Audio Sound

SAP

A stereo TV with AUDIO/VIDEO input jacks or a ste-

reo audio system is required for true stereo playback.

To experience the full and rich stereo sound available

with Hi-Fi recorded tapes, we recommend the con-

nection of this unit to a home stereo audio system.

Some stations transmit a Second Audio Program,

which is used for a second language or additional

information.

STEREO/SAP

Use the BROADCAST TYPE option to select the

desired recording mode (STEREO or SAP).

1. Set the AUDIO MODE option to HI-FI on the VCR

SETUP menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

To record one TV program while watching

another

VCR Tape Recording

1. Press TV/VCR to select the TV mode during

recording. The TV indicator appears.

Basic Instructions

1. Turn on the DVD+VCR and TV.

2. Using the TV, select the channel to be viewed.

2. Tune the TV to the DVD+VCR output channel (CH

3 or 4) or if a direct VIDEO/AUDIO connection is

made between the DVD+VCR and the TV, set the

TV’s source selector to VIDEO.

Timer Recording

For unattended recording, you must input the

channels to be recorded and the starting and ending

times.

3. Insert a video cassette with the safety tab intact.

4. Select the desired channel using CH (-/+).

Things to know before starting

5. If you are recording from another source via

audio/video input jacks (at the rear or front panel),

select LINE1 or LINE2 using AUX.

If you try to set the program timer before setting the

clock, “PLEASE SET THE CLOCK” appears for a

moment and then CLOCK menu appears on the TV

screen. Set the time and date before proceeding.

6. Set the desired recording speed (SP or SLP) by

pressing SPEED. This DVD+VCR is not designed

to record in LP mode.

1. Turn on the DVD+VCR and the TV.

7. Set the MTS mode (STEREO or SAP). Set the

BROADCAST TYPE option to SAP if applicable.

2. Be sure the TV is set to the DVD+VCR output

channel (3 or 4).

8. Press REC (z) and recording starts. The REC

indicator appears in the display window. If a cas-

sette with no safety tab is loaded, the cassette is

ejected.

3. Make sure the TUNING BAND in the TUNING

menu is set appropriately (TV or CATV).

4. Press SETUP MENU and the MAIN menu

appears.

9. Press STOP (x) to stop recording. If the tape

reaches the end before STOP (x) is pressed, the

DVD+VCR stops, rewinds and ejects the tape.

5. Use v / V to choose the PROGRAM menu and

press ENTER/OK.

Tip:

Use PAUSE (X) for best results when making

changes while recording. For example, if you want to

change channels while recording, first press PAUSE

(X) to put the unit in pause mode, select the desired

channel on the DVD+VCR, and then press PAUSE

(X) again to resume recording.

If eight programs are already entered, the FULLY

PROGRAMMED message appears for a moment

and then PROGRAM 1 appears on the TV screen.

Note:

During the VCR recording mode, you cannot change

to the DVD mode.

6. Use the v / V buttons to switch between the

program options, and the b / B buttons to input

the program information:

To pause the recording

Input the month, day, start and stop times of the

program you want to record.

1. Press PAUSE (X) to pause the tape during record-

ing. The REC indicator flashes in the display win-

dow.

2. When you want to continue recording, press

PAUSE (X) or press REC (z).

After 5 minutes in PAUSE mode, the DVD+VCR

stops automatically to protect the tape and the

video heads.

Download from Www.Somanuals.com. All Manuals Search And Download.

CHANNEL: Select a TV channel, LINE1 or LINE2.

If you have CABLE TV and use a cable box

(converter) you must set the channel to match

the cable box output channel (usually CH 3 or

4). Change channels on the cable box instead of

with the DVD+VCR. If you use a cable converter,

you can program multiple recordings only on the

converter box output channel. This is because

the converter determines what channel you view

through your DVD+VCR.

Checking or Erasing the Timer Program

Programming can be checked whenever the

DVD+VCR is turned on.

1. Press SETUP MENU and the MAIN menu

appears.

2. Use v / V to choose the PROGRAM menu and

press ENTER/OK.

SPEED: AUTO mode determines how much tape

is left and switches the speed from SP to SLP if it

is necessary to complete recording the program. If

this occurs there could be some picture and sound

distortion at the point where the speed changes.

3. Use b / B to select a program you want to check

or erase. To erase the program, press CLEAR

(0000).

REPEAT: To record up to 8 programs on a certain

day of every week select WEEKLY. To record up

to 8 programs at the same time Monday through

Friday select DAILY. Otherwise select ONCE.

4. Press SETUP MENU to return to the TV screen.

7. Press SETUP MENU and the program is memo-

rized by the DVD+VCR.

Program Priority

If the recording start and end times of preset pro-

grams overlap on the same day (see the example),

the second program is not recorded until the first is

finished.

8. Additional programs may be entered by repeating

steps 1-7.

9. Ensure you insert a tape with the record safety tab

intact before the first programmed time.

10. Press STOP (x) to end timer recording.

Notes:

• If you make a mistake or want to change a setting,

use v to select the option and correct it using b / B.

• If the program preset time is past, the “PAST TIME

PROGRAMMED” message appears on the TV

screen. Return to the incorrect program and pro-

gram it with the correct time.

In this example, the first part of program numbers 2

and 3 are not recorded.

• If you enter a past date, the timer recording will be

performed on that date of the next year.

• If the power fails or the DVD+VCR is unplugged the

clock and timer settings are kept in memory for only

3 seconds. Otherwise you must reset the clock and

timer.

• If the tape indicator is blinking, no tape is loaded.

• When you are playing DVD at programmed

Recording time, the DVD+VCR automatically

change to VCR mode and start recording.

• The DVD+VCR will automatically power off when

Timer Recording ends.

Download from Www.Somanuals.com. All Manuals Search And Download.

Extending the Recording Time

Instant Timer Recording

The recording time can be extended anytime by

pressing REC (z). Subsequent presses result in

advancing the recording time by 30-minute

increments.

With this feature you can record for a preset length

without using the program timer.

1. Turn on DVD+VCR and the TV.

2. Be sure the TV is tuned to the DVD+VCR output

channel (CH 3 or 4). If a direct VIDEO/AUDIO con-

nection is made between the DVD+VCR and the

TV, set the TV’s source selector to VIDEO.

Note:

If you press PAUSE (X) during instant timer recording,

the instant timer recording is cancelled.

3. Insert a video cassette with the safety tab intact.

4. Select the desired channel using CH (-/+) or

the number buttons (0-9). The channel number

appears on the TV screen. If you are recording

from another source via audio/video input jacks (at

the rear or front panel), select LINE1 (rear jacks)

or LINE2 (front jacks) by using AUX.

Recording from External Components

You can record from an external component, such

as a camcorder or VCR, connected to any of the

DVD+VCR’s external inputs.

1. Make sure that the component you want to record

from is connected properly to the DVD+VCR. See

page 13.

5. Set the desired recording speed (SP or SLP)

using SPEED. The tape speed appears on the TV

screen.

2. Press AUX repeatedly to select the external input

to record from.

6. Press REC (z) twice. The menu appears on the

TV screen, recording starts, and the

indicator lights.

(TIMER)

• LINE1 (L1): Audio/Video Input mounted on back

panel.

• LINE2 (L2): Audio/Video Input mounted on front

panel.

INSTANT TIMER RECORD

CHANNEL

SPEED

3. Load a recordable tape.

4. Set a recording mode (SP or SLP) as necessary

by pressing SPEED repeatedly.

START

LENGTH

NOW

0H30M

5. Play the tape or disc in the external component.

If you have a TV attached to your DVD+VCR, you

can see the video playing.

7. Press REC (z) repeatedly to select the record-

ing time length. Each time you press this button

the recording time increases 30 minutes (up to 9

hours). At the end of the recording, the DVD+VCR

will stop recording and shut off.

6. Press REC (z) once to start recording.

The REC indicator lights in the display window.

7. Press STOP (x) to stop recording.

If you set the time to 0H00M, the DVD+VCR goes

into the normal recording mode. Press STOP (x)

to stop the recording.

Notes:

• Before recording, confirm the recording start posi-

tion.

Note:

• If your source is copy-protected using CopyGuard,

you will not be able to record it using this unit. See

During Instant Timer Recording, you cannot change

the channel on the DVD+VCR.

• To record for a fixed length of time, see Instant

Timer Recording.

Checking the Recording Time

Press REC (z) once to check the recording time. The

recalled setting automatically returns to the TV screen

after 6 seconds.

Download from Www.Somanuals.com. All Manuals Search And Download.

Each press of the ENTER/OK changes the TV screen

in the following sequence.

Copying from DVD to VCR

You can copy the contents of a DVD to a VHS tape.

STOP

STEREO

1. Insert the disc you wish to copy into the DVD deck

and close the disc tray.

2. Insert a blank VHS video tape into the VCR deck.

APR 30 , SAT

2:15 PM

3. Find the place on the DVD from which you want

to start dubbing using the PLAY, FF, REW and

PAUSE functions.

2:15 PM

0:35:40

REM 1:58

For best results, pause playback at the point from

which you want to record.

4. Press REC (z). The DVD goes into PLAY mode

and the VCR goes into RECORD mode. If the

DVD disc menu appears, you may need to press

PLAY (N) manually to begin copying.

Real-Time Counter

If a tape with contents recorded on it is inserted into

the VCR, the real-time counter shows length of the

tape running in hours, minutes, and seconds. Press

DISPLAY to select the real-time counter display. Every

press of DISPLAY changes the TV screen as illus-

trated below.

5. When the DVD is finished playing, press STOP (x)

to end copying.

Notes:

2:15 AM

CLOCK

0:05:25

COUNTER

REM 1:07

• If you use the DISPLAY or ZOOM function during

copying, the information displayed on-screen will be

recorded.

REMAINING TIME

Counter Memory

• If the DVD you are attempting to copy is copy pro-

tected, you will not be able to copy the disc. It is not

permitted to copy Macrovision encoded DVDs (or

Discs). “Lock” is displayed in the display window.

This feature is useful if there is a section of tape you

want to view immediately after recording or if you want

to return to the same point several times.

1. Begin recording or playing a tape.

• You must stop the copy process manually when the

DVD movie ends, or the unit may replay and record

over and over again.

2. Press DISPLAY until the real-time counter is dis-

played on the TV screen.

3. At the point that you want to locate later, reset the

real-time counter to “0:00:00” by pressing CLEAR

(0000).

• When you stop the DVD playback during copying,

the recording on VCR is stopped automatically.

4. Continue to play or record.

5. Press STOP (x) when recording or playback fin-

ishes.

On-Screen Display - VCR

Some of these functions will be displayed every time

the DVD+VCR is operated.

6. Press REW (m). The tape automatically stops

when the tape counter returns to about “0:00:00”.

Tape Remaining

This function displays the amount of time remaining on

the tape during recording or playback. Press DISPLAY

repeatedly until the REM indicator displays on the TV

screen during recording or playback.

The remaining tape length may not be displayed cor-

rectly depending on the condition of the tape and the

❶

❷

❸

❹

❺

PLAY

HI-FI

CH 4

STEREO

kind of the tape (T-140, T-160, or T-210 etc.).

Notes:

OCT 8 , SAT

2:15 PM

• The function displays can be seen displayed on the

TV screen for 5 seconds.

❻

❼

• The clock (or tape counter, tape remaining) mode

will be displayed until you press ENTER/OK.

A TAPE SPEED DISPLAY

B FUNCTION DISPLAY

C HI-FI DISPLAY

E STEREO/SAP DISPLAY

(MONO is not displayed)

• The tape counter and the remaining tape length

indicator appear only when a cassette is inserted.

Also, the remaining tape length indicator appears

after any tape operation.

F DATE DISPLAY

G CLOCK/ COUNT/

D CHANNEL DISPLAY

REMAIN DISPLAY

Download from Www.Somanuals.com. All Manuals Search And Download.

S-VHS Quasi Playback (SQPB)

Additional VCR Information

• During manual recording, timer recording, Instant

Timer Recording, playback, or fast forward modes,

the DVD+VCR automatically starts rewinding the

tape at the end of the tape. The cassette stops at

the beginning of the tape and is ejected.

• This DVD+VCR can play back S-VHS recorded

tapes, however, it cannot make recordings using

S-VHS format tapes.

• SQPB is an abbreviation for S-VHS Quasi Playback.

• After you have finished using the DVD+VCR,

rewind, eject, and remove the cassette. Place the

cassette in its protective sleeve to protect it from

dust. It is not necessary to rewind the cassette

before removing it, but if you do, it is ready to play

or record the next time you use it.

Easy Information

If the Extended Data Service (XDS) signals are pro-

vided along with normal TV signal in your area or

during playback of a tape recorded with Extended

Data Service (XDS) signals, the station ID, program

title, and program details are shown on the TV screen.

When viewing a channel with Extended Data Service

(XDS) signals, press ENTER/OK and the station ID

will appear on the TV screen. Press ENTER/OK again

and the program details will appear on the TV screen.

• Be sure the DVD+VCR channel selector is on the

correct channel you wish to record. The channel

that is being recorded can always be checked by

setting the television on the DVD+VCR channel

(CH 3 or 4) and pressing the TV/VCR to turn the

DVD+VCR’s TV indicator off.

When viewing a tape recorded with Extended Data

Service (XDS) signals, press ENTER/OK twice and

the program title and program details will appear on

the TV screen.

• Do not attempt to hook up more than one television

set to the DVD+VCR for either recording or play-

back.

Program Details

VCR Auto Play System

LENGTH: Indicates the run length of a program.

TIME REMAINING: Indicates the remaining time of a

program.

This DVD+VCR features automatic playback.

RATING: Indicates the rating of the current program

(N/A, G, PG, PG-13, R, NC-17, X and Not Rated). The

rating N/A means that the motion picture ratings are not

applicable to this program.

When you load a tape with the safety tab removed the

following occurs:

• The Output Source is changed to VCR mode

automatically.

• The power turns on automatically and playback

begins.

WABC

STEREO

• At the end of the tape, the DVD+VCR stops, then

rewinds.

• The tape is ejected after rewinding and the turns

itself off automatically.

“Home video”

APR 30 , SAT

2:15 PM

Easy Information Screen

(Station ID)

PROGRAM DETAILS

“Home video”

Note:

LENGTH 01:00

TIME REMAINING 00:26

RATING N/A

Auto power off does not function during regular DVD play

mode. (DVD+VCR power stays on.)

Easy Information Screen

(Program details)

Download from Www.Somanuals.com. All Manuals Search And Download.

Operations - DVD

Playback Setup

• Turn the TV on and select the video input source connected to this unit.

• Audio System: Turn the Audio System on and select the input source connected to this unit.

1. Press OPEN/CLOSE (Z) to open the disc tray.

2. Load your chosen disc in the tray with the playback side down.

3. Press OPEN/CLOSE (Z) to close the tray.

READING appears on the display window, and playback starts automatically.

If playback does not start, press PLAY (N).

In some cases, the disc menu might appear instead.

General features

Buttons

Operations

Discs

Opens or closes the disc tray.

OPEN/CLOSE (Z)

STOP (x)

ALL

During playback, press STOP (x) to stop playback. The unit

records the stop point depending on the disc. “Xx” appears

on the screen briefly.

ALL

If you press STOP (x) again, “x” appears on the screen

and the unit will clear the stop point.

PAUSE (X)

ALL

DVD

ALL

During playback, press X to pause playback.

Press X repeatedly to play Frame-by-Frame.

VCD

SKIP (. / >)

During playback, press SKIP (. or >) to go to the next

chapter/track or to return to the beginning of the current

chapter/track.

Press SKIP (.) twice briefly to step back to the previous

chapter/track.

REW/FF (m / M) During playback, press REW (m) or FF (M) repeatedly

DVD

VCD

ACD

to select the required scan speed.

DVD: 4 steps

Video CD, Audio CD: 3 steps

While the playback is paused, press FF (M) repeatedly to

play in slow motion (4 steps, forward only).

DVD

ALL

REPEAT

During playback, press REPEAT repeatedly to select a

desired repeat mode.

DVD Video discs: Chapter/Title/Off

Video CD, Audio CD: Track/All/Off

Notes:

• If you press SKIP (>) once during Repeat Chapter

playback, the repeat playback cancels.

• For Video CD with PBC, you must set PBC to Off on the

Setup menu to use this function. (See “PBC” on page 18.)

REPEAT A-B

During playback, each press of REPEAT A-B button to

select point A and point B and repeats a sequence from

point A (Starting point) to point B (End point).

DVD

VCD

ACD

Note:

The A-B repeat function is available only in the current track.

Download from Www.Somanuals.com. All Manuals Search And Download.

Buttons

Operations

Discs

ZOOM

During playback or pause mode, press ZOOM to enlarge

the video image (3 steps).

DVD

VCD

JPEG

You can move through the zoomed picture using b B v V

buttons. Press CLEAR (0000) to exit.

Notes:

• Zoom may not work on some DVDs.

• For JPEG files, the zoom function is not available when

the resolution is set to 720p or 1080i.

RANDOM

TITLE

During playback or in stop mode, press RANDOM for ran-

dom playback.

ACD

DVD

If the current DVD title has a menu, the title menu appears

on the screen. Otherwise, the disc menu may appear.

DISC MENU

The disc menu appears on the screen.

DVD

During playback of DVD disc contains scenes recorded dif-

ferent camera angles, press ANGLE repeatedly to select a

desired angle.

(ANGLE)

Tip:

The Camera Angle icon is displayed on the TV screen when

alternate angles are available.

During playback, press SUBTITLE repeatedly to select a

desired subtitle language.

DVD

(SUBTITLE)

(AUDIO)

During playback, press A.MONITOR repeatedly to hear a

different audio language or audio track.

VCD

DVD

VCD

Time Search

Additional features

To start playing at any chosen time on the disc:

1. Press DISPLAY during playback.

3D Surround

To produce a 3D surround effect that simulates mul-

tichannel audio from two stereo speakers (instead of

the five+ speakers normally required for multi-channel

audio from a home theater system).

2. Press v / V to select the time clock icon and

“--:--:--” appears.

3. Input the required start time in hours, minutes,

and seconds from left to right. If you enter the

wrong numbers, press CLEAR (0000) to remove

the numbers you entered. Then input the correct

numbers.

DVD

VCD

1. Press DISPLAY during playback.

2. Use v or V to select the sound option.

4. Press ENTER/OK to confirm. Playback starts from

the selected time.

The sound option will be highlighted.

3. Use b or B to select “3D SUR”.

To turn off the 3D Surround effect, select “Normal”.

DVD

VCD

Marker Search

To enter a Marker

ACD

You can start playback from up to nine memorized

points. To enter a marker, press MARKER at the

desired point on the disc. The Marker icon appears

on the TV screen briefly. Repeat to enter up to nine

markers.

1. Press A.MONITOR during playback.

“3D SUR” appears on the menu screen.

2. To return to normal playback, press A.MONITOR

repeatedly until “3D SUR” disappears from the

menu screen.

Download from Www.Somanuals.com. All Manuals Search And Download.

To Recall or Clear a Marked Scene

Programmed Playback

The program function enables you to store your favor-

ite tracks from any disc in the player memory.

1. During disc playback, press SEARCH. The marker

search menu appears on the screen.

2. Within 10 seconds, press b / B to select a marker

A program can contain 30 tracks.

number that you want to recall or clear.

1. Insert an Audio CD.

3. Press ENTER/OK and playback starts from the

marked scene. Or, press CLEAR (0000) and the

marker number is erased from the list.

AUDIO CD menu appears.

2. During STOP mode, press PROGRAM and the

mark will appear.

4. You can play any marker by inputting its number

on the marker search menu.

Note:

Press PROGRAM again to exit the program edit

DVD

ACD

VCD1.1

Last Scene Memory

mode, then the

mark will disappear.

This player memorizes last scene from the last disc

that is viewed. The last scene remains in memory

even if you remove the disc from the player or switch

off the player. If you load a disc that has the scene

memorized, the scene is automatically recalled.

3. Select a track on the “List”, then press ENTER/OK

to place the selected track on the “Program” list.

Repeat to place additional tracks on the list.

4. Select the track you want to start playing on the

“Program” list.

Note:

5. Press PLAY (N) or ENTER/OK to start. Playback

begins in the order in which you programmed the

tracks. Playback stops after all of the tracks on the

“Program” list have played once.

This player does not memorize the scene of a disc if

you switch off the player before commencing to play

the disc.

6. To resume normal playback from programmed

playback, select a track on the list and then press

PLAY (N).

Screen Saver

The screen saver appears when you leave the

DVD+VCR in Stop mode for about five minutes.

Repeat Programmed Tracks

Press REPEAT to select a desired repeat mode.

• Track: repeats the current track

• All: repeats all the tracks on programmed list.

• Off (No display): does not play repeatedly.

Note:

Playing an Audio CD

This unit can play Audio CDs.

Audio CD

Once you insert an Audio CD, a menu appears on the

TV screen. Press v/V to select a track then press

PLAY (N) or ENTER/OK and playback starts. You

can use variable playback functions. Refer to pages

26 - 28.

If you press SKIP (>) once during Repeat Track

playback, the repeat playback cancels.

Erasing a Track from “Program” List

1. During STOP mode, press PROGRAM and the

mark will appear

2. Use vVbB to select the track that you wish to

erase from the Program list.

3. Press CLEAR (0000). Repeat step 1~3 to erase

additional tracks on the list.

Erasing the Complete Program List

1. During STOP mode, press PROGRAM and the

mark will appear

2. Use vVbB to select “Clear All”, then press

ENTER/OK.

Note:

When playing an Audio CD with HDMI OUT as the

output, the beginning of some songs may not be

played.

The programs are also cleared when the power is off

or the disc is removed.

Download from Www.Somanuals.com. All Manuals Search And Download.

Slide Show

Viewing a JPEG File

Using this DVD+VCR you can view discs with JPEG

files.

Use vVbB to highlight the

press ENTER/OK.

(Slide Show) then

Still Picture

1. Press PAUSE (X) during slide show.

1. Insert a disc and close the tray. The PHOTO menu

appears on the TV screen.

The player will now go into PAUSE mode.

2. To return to the slide show, press PLAY (N) or

press PAUSE (X) again.

Moving to another File

Press SKIP (> or .) or cursor (b or B) once

while viewing a picture to advance to the next or

previous file.

Zoom

Use zoom to enlarge the photo image. (See page 27.)

Note:

2. Press v/V to select a folder, and press ENTER/

OK. A list of files in the folder appears.

When the resolution is set to 720p or 1080i, this func-

tion is not available.

If you are in a file list and want to return to the

previous Folder list, use the v/V buttons on the

To rotate picture

remote to highlight

and press ENTER/OK.

Press v/V during showing a picture to rotate the pic-

ture clockwise or counter clockwise.

3. If you want to view a particular file, press v/V

to highlight a file and press ENTER/OK or PLAY

(N). The selected file will appear for viewing.

While viewing a file, you can press STOP (x) to

move to the previous menu (PHOTO menu).

JPEG disc compatibility with this player is

limited as follows:

Tips:

• Depending upon the size and number of JPEG

files, it could take a long time for the DVD+VCR

to read the disc’s contents. If you don’t see an

on-screen display after several minutes, some

of the files may be too large — reduce the

resolution of the JPEG files to less than 5760

(Horizontal) x 3840 (Vertical) pixels and burn

another disc.

• Information and user guidance regarding the current

image is displayed in the lower part of the screen.

You can toggle this bar on and off using RETURN

(O).

• There are three Slide Speed options

>>> (Fast), >> (Normal) and > (Slow)

Use vVbB to highlight the Speed. Then, use b/B

to select the option you want to use then press

ENTER/OK.

• The total number of files in a folder should be

less than 1190 files.

• Some discs may be incompatible due to a differ-

ent recording format or the condition of disc.

Note:

When viewing a JPEG file, the user guidance will not

be displayed on the TV screen if the resolution is set

to 720p or 1080i.

• Ensure that all the selected files have the “.jpg”

extensions when copying into the CD layout.

• If the files have “.jpe” or “.jpeg” extensions, please

rename them as “.jpg” file.

• File names without “.jpg” extension will not be

able to be read by this DVD+VCR. Even though

the files are shown as JPEG image files in

Windows Explorer.

Download from Www.Somanuals.com. All Manuals Search And Download.

Playing a DVD VR Format Disc

Maintenance and Service

This unit will play DVD-R/RW discs recorded using the Refer to the information in this chapter before contact-

DVD-Video format that have been finalized using a

DVD-recorder.

ing a service technician.

Handling the Unit

When shipping the unit

• This unit will play DVD-RW discs recorded using

the Video Recording (VR) format.

1. Insert a disc and close the tray, It start playing

automatically.

Please save the original shipping carton and packing

materials. If you need to ship the unit, for maximum

protection, re-pack the unit as it was originally packed

at the factory.

2. The DVD-VR menu appears on the TV screen

when you press DISC MENU buttons while play-

ing.

Keeping the exterior surfaces clean

• Do not use volatile liquids such as insecticide spray

near the unit.

• Do not leave rubber or plastic products in contact

with the unit for a long period of time since they

leave marks on the surface.

Cleaning the unit

3. Press v/V to select a track then press PLAY (N)

To clean the player, use a soft, dry cloth. If the sur-

faces are extremely dirty, use a soft cloth lightly moist-

ened with a mild detergent solution.

or ENTER and playback starts.

4. Press DISC MENU to move to the list menu.

Do not use strong solvents such as alcohol, benzene,

or thinner, as these might damage the surface of the

unit.

Notes:

• Unfinalized DVD-R/RW discs cannot be played in

this player.

• Some DVD-VR disc are made with CPRM data by

DVD RECORDER. Player does not support these

kinds of discs.

Maintaining the Unit

The DVD+VCR is a high-tech, precision device. If the

optical pick-up lens and disc drive parts are dirty or

worn, the picture quality could be diminished.

What is ‘CPRM’?

CPRM is a copy protection system (with scramble

system) only allowing the recording of ‘copy once’

broadcast programs. CPRM stands for Content

Protection for Recordable Media.

This player is CPRM compatible, which means that

you can record copy-once broadcast programs, but

you cannot then make a copy of those recordings.

CPRM recordings can only be made on DVD-RW

discs formatted in VR mode, and CPRM recordings

can only be played on players that are specifically

compatible with CPRM.

Depending on the operating environment, regular

inspection and maintenance are recommended after

every 1,000 hours of use.

For details, please contact your nearest authorized

service center.

Download from Www.Somanuals.com. All Manuals Search And Download.

Reference

Language Codes List

Use this list to input your desired language for the following initial settings:

Disc Audio, Disc Subtitle, Disc Menu.

Language

Abkhazian

Afar

Afrikaans

Albanian

Ameharic

Arabic

Armenian

Assamese

Aymara

Azerbaijani

Bashkir

Basque

Bengali; Bangla

Bhutani

Bihari

Breton

Bulgarian

Burmese

Byelorussian

Cambodian

Catalan

Chinese

Corsican

Croatian

Czech

Code

6566

6565

6570

8381

6577

6582

7289

6583

6588

6590

6665

6985

6678

6890

6672

6682

6671

7789

6669

7577

6765

9072

6779

7282

6783

6865

7876

6978

6979

6984

7079

Language

Fiji

Finnish

French

Frisian

Galician

Georgian

German

Greek

Greenlandic

Guarani

Gujarati

Hausa

Code

7074

7073

7082

7089

7176

7565

6869

6976

7576

7178

7185

7265

7387

7273

7285

7383

7378

7365

7165

7384

7465

7487

7578

7583

7575

7589

7579

7585

7679

7665

7686

Language

Lingala

Lithuanian

Macedonian

Malagasy

Malay

Malayalam

Maltese

Maori

Code

7678

7684

7775

7771

7783

7776

7784

7773

7782

7779

7778

7865

7869

7879

7982

8065

8083

7065

8076

8084

8185

8277

8279

8285

8377

8365

7168

8382

8372

8378

8368

Language

Singhalese

Slovak

Slovenian

Somali

Spanish

Sudanese

Swahili

Swedish

Tagalog

Tajik

Code

8373

8375

8376

8379

6983

8385

8387

8386

8476

8471

8465

8484

8469

8472

6679

8473

8479

8482

8475

8487

8575

8582

8590

8673

8679

6789

8779

8872

7473

8979

9085

Marathi

Moldavian

Mongolian

Nauru

Nepali

Norwegian

Oriya

Panjabi

Pashto, Pushto

Persian

Tamil

Tatar

Hebrew

Hindi

Telugu

Thai

Tibetan

Tigrinya

Tonga

Turkish

Turkmen

Twi

Ukrainian

Urdu

Hungarian

Icelandic

Indonesian

Interlingua

Irish

Polish

Italian

Portuguese

Quechua

Rhaeto-Romance

Rumanian

Russian

Samoan

Sanskrit

Scots Gaelic

Serbian

Japanese

Javanese

Kannada

Kashmiri

Kazakh

Kirghiz

Uzbek

Vietnamese

Volapük

Welsh

Wolof

Xhosa

Yiddish

Yoruba

Zulu

Danish

Dutch

English

Esperanto

Estonian

Faroese

Korean

Kurdish

Laothian

Latin

Serbo-Croatian

Shona

Sindhi

Latvian, Lettish

Area Codes List

Choose an area code from this list.

Area

Code

Area

Ethiopia

Fiji

Code

Area

Code

Area

Saudi Arabia

Senegal

Singapore

Slovak Republic

Slovenia

South Africa

South Korea

Spain

Sri Lanka

Sweden

Switzerland

Taiwan

Thailand

Turkey

Code

Afghanistan

Argentina

Australia

Austria

Belgium

Bhutan

Bolivia

Brazil

Cambodia

Canada

Chile

China

Colombia

Congo

Costa Rica

Croatia

Czech Republic

Denmark

Ecuador

Egypt

Malaysia

Maldives

Mexico

Finland

France

Germany

Great Britain

Greece

Greenland

Islands

Hong Kong

Hungary

India

Indonesia

Israel

Italy

Jamaica

Japan

Kenya

Monaco

Mongolia

Morocco

Nepal

Netherlands

Netherlands Antilles

New Zealand

Nigeria

Norway

Oman

Pakistan

Panama

Paraguay

Philippines

Poland

Portugal

Romania

Russian Federation

Uganda

Ukraine

United States

Uruguay

Uzbekistan

Vietnam

Kuwait

Libya

Luxembourg

El Salvador

Zimbabwe

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

Check the following guide for the possible cause of a problem before contacting service.

Symptom

No power.

Cause

Correction

• The power cord is disconnected.

• Plug the power cord into the wall

outlet securely.

Abnormal or no picture

• The TV is not set to receive

DVD+VCR signal output.

• Insert a disc or tape. (Check that the

disc or tape indicator in the display

window is lit.)

• The video cable is not connected

securely.

• Select the appropriate video input

mode on the TV so the picture from

the DVD+VCR player appears on the

TV screen.

• The HDMI mode is on.

• Set HDMI on the front panel to OFF.

• Unit output setting and TV resolution • Check TV capability.

capabilities mismatch.

• Check mode of connections

(e.g. S-Video, Components etc.).

• Check unit Resolution setting

according to TV capability and mode

of connection.

• Wrong cable connection.

• Check the connection.

Distorted or no sound.

• The equipment connected with the

audio cable is not set to receive

DVD+VCR signal output.

• Select the correct input mode of the

audio receiver so you can listen to

the sound from the DVD+VCR.

• The audio cables are not connected

securely.

• Connect the audio cable into the

jacks securely.

• The power of the equipment con-

nected with the audio cable is turned

off.

• Turn on the equipment connected

with the audio cable.

• The AUDIO options are set to the

wrong position.

• Set the AUDIO options to the correct

position.

• In HDMI mode, audio selection is not • Change AUDIO setup to PCM mode.

set to PCM.

The playback picture is

poor.

• The disc is dirty.

• Clean the disc.

• The TV channels are not tuned in

properly.

• Check tuning, carry out tuning again.

• Tape heads are dirty.

• Clean video heads.

• Tape is a rental or was recorded on

another VCR.

• Use CH (-/+) for manual tracking

adjustment while tape is playing.

Download from Www.Somanuals.com. All Manuals Search And Download.

Symptom

Cause

• No disc is inserted.

Correction

The DVD+VCR does not

start playback.

• Insert a disc or tape. (Check that the

disc or tape indicator in the display

window is lit.)

• No tape is inserted.

• An unplayable disc is inserted.

• Insert a playable disc. (Check the

disc type and Regional code.)

• The disc is placed upside down.

• Place the disc with the playback side

down.

• The disc is not placed within the

guide.

• Place the disc on the disc tray cor-

rectly inside the guide.

• The disc is dirty.

• Clean the disc.

Video tape cannot be

inserted.

• Is the cassette compartment empty? • Eject the tape in.

No Hi-Fi sound

• Audio mode is not set properly.

• Select STEREO by repeatedly

pressing A.MONITOR on the remote

control.

• There is an obstacle in the path of

the remote control and this unit.

• Remove the obstacle.

The remote control does

not work properly.

• The batteries in the remote control

are exhausted.

• Replace the batteries with new ones.

• The remote control is not pointed at

the remote sensor of the DVD+VCR.

• Point the remote control at the

remote sensor of the DVD+VCR.

• The remote control is too far from the • Operate the remote control within

DVD+VCR.

23 ft (7m).

• This remote control use the same

buttons for VCR and DVD functions

(ex. PLAY).

• When using a VCR, first press the

VCR button. When using a DVD, first

press the DVD button.

Camcorder image is not

shown.

• Camcorder is off.

• Turn camcorder on and operate

properly.

Camcorder image via AV • DVD+VCR SOURCE SELECT is not • Press AUX to select LINE input

input to DVD+VCR is not

shown on TV screen.

set to LINE1 or LINE2.

channel (LINE1 or LINE2).

Timer recording is not

possible.

• Clock in DVD+VCR is not set to cor- • Set clock to correct time.

rect time.

• Timer has been programmed incor-

rectly.

• Reprogram Timer.

• Reprogram Timer and turn

DVD+VCR off to enable timer.

•

indicator light does not appear

after programming timer.

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

General

Power requirements

120 V, 60 Hz

Power consumption

Dimensions (approx.)

Weight (approx.)

Operating temperature

Operating humidity

Signal system

18 W

16.9" X 3.1" X 10.4" (430 X 78.5 X 265 mm) (w x h x d)

9.26 lbs (4.2 kg)

5˚C to 40˚C (41˚F to 104˚F)

5 % to 90 %

NTSC

Inputs

ANTENNA IN

VHS VIDEO IN (LINE1, 2)

VHS AUDIO IN (LINE1, 2)

75 ohms (VHF/UHF/CATV)

1 V (p-p) 75 ohms, sync negative, RCA jack x 2

-6.0 dBm more than 47 ohms, RCA jack (L, R) x 2

Outputs

VIDEO OUT

1 V (p-p) 75 ohms, sync negative

S-VIDEO OUT

(Y) 1.0 V (p-p), 75 ohms, negative sync, Mini DIN 4-pin x 1

COMPONENT VIDEO OUT

(PROGRESSIVE SCAN)

HDMI OUT

(Y) 1.0 V (p-p), 75 ohms, negative sync, RCA jack x 1

(Pb)/(Pr) 0.7 V (p-p), 75 ohms, RCA jack x 2

19-pin x 1, Corresponding to HDCP

Video: 480p/720p/1080i

Audio: 2 ch PCM/Bitstream

Audio output (digital audio)

Audio output (analog audio)

RF OUT

0.5 V (p-p), 75 ohms, RCA jack x 1, OPTICAL x 1

2.0 Vrms (1 KHz, 0 dB), 600 ohms, RCA jack (L, R) x 1

Channel 3 or 4 (Adjustable)

VCR Specifications

Head system

Timer

Tape speed

Four head helical scan azimuth system

12-hour display type with AM, PM

SP: 33.35 mm/sec, LP: 16.67 mm/sec, SLP: 11.12 mm/sec

12.7 mm

Tape width

Maximum recording time

Rewind time

SP: 2 HOURS (T-120), SLP: 6 HOURS (T-120)/8 HOURS (T-160)

About 3 minutes (T-120)

Channel coverage

Frequency range

Signal-to-noise ratio

Dynamic range

Channel separation

VHF: 2-13, UHF: 14-69, CATV: 1-125 (4A, A-W, W+1 - W+84, A-5 - A-1)

20 Hz to 20 kHz

More than 43 dB

More than 88 dB

More than 60 dB

DVD Specifications

Laser system

Frequency response

Semiconductor laser, wavelength 650 nm

DVD (PCM 96 kHz): 8 Hz to 44 kHz,

DVD (PCM 48 kHz): 8 Hz to 22 kHz

CD: 8 Hz to 20 kHz

Signal-to-noise ratio

Harmonic distortion

Dynamic range

More than 100 dB (ANALOG OUT jacks only)

Less than 0.008%

More than 95 dB (DVD/CD)

Accessories:

RF 75-ohm Coaxial Cable x 1, Remote control x 1, Batteries (R03/AAA) x 2

• Design and specifications are subject to change without prior notice.

Download from Www.Somanuals.com. All Manuals Search And Download.

Warranty (Only in U.S.A.)

Download from Www.Somanuals.com. All Manuals Search And Download.

Printed in Indonesia

0306MNH-SW-LG

Download from Www.Somanuals.com. All Manuals Search And Download.

Insignia Flat Panel Television NS lcd19 User Manual
Intel Computer Hardware BLKDZ68BC User Manual
JBL Speaker PSW D112 User Manual
JVC DVD Player LVT2008 029A User Manual
JVC Headphones HA W600RF B User Manual
JVC Stereo System CA EXA5 User Manual
Kenmore Range 7909031 User Manual
KitchenAid Cooktop KGCV566R User Manual
KitchenAid Refrigerator W10366208A User Manual
Kodak Digital Camera CD913 User Manual