DVD PLAYER &
VIDEO CASSETTE RECORDER
HR-XVC11B
HR-XVC12S
For customer use:
Enter below the Model No. and
Serial No. which are located on the
rear of cabinet. Retain this
information for future reference.
Model No.
Serial No.
INSTRUCTIONS
LVT1866-001A
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNER’S MANUAL. AND
CAUTION:
THOSE MARKED ON THE PRODUCT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE.
This product has been designed and manufactured to assure personal safety. Improper use can result in electric shock or
fire hazard. The safeguards incorporated in this product will protect you if you observe the following procedures for installa-
tion, use, and servicing.
This product does not contain any parts that can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER SERVIC-
ING TO QUALIFIED SERVICE PERSONNEL ONLY.
1. Read these instructions. - All these safety and operating
instructions should be read before the product is operated.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience recepta-
cles, and the point where they exit from the product.
2. Keep these instructions. - The safety, operating and use
instructions should be retained for future reference.
11. Only use attachments/accessories specified by the
manufacturer.
3. Heed all warnings. - All warnings on the product and in
the operating instructions should be adhered to.
12. Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with appara-
tus. When a cart is used, use caution when moving
the cart/product combination to avoid injury from
tip-over.
4. Follow all instructions. - All operating and use instruc-
tions should be followed.
5. Do not use this product near water. – For example: near
a bath tub, wash bowl, kitchen sink, laundry tub, in a wet
basement; or near a swimming pool; and other areas
located near water.
6. Clean only with dry cloth. – Unplug this product from the
wall outlet before cleaning. Do not use liquid cleaners.
7. Do not block any ventilation openings. Install in accor-
dance with the manufacturer’s instructions. - Slots and
openings in the cabinet are provided for ventilation and to
ensure reliable operation of the product and to protect it
from over- heating. The openings should never be blocked
by placing the product on a bed, sofa, rug or other similar
surface. This product should not be placed in a built-in
installation such as a bookcase or rack unless proper ven-
tilation is provided or the manufacturer’s instructions have
been adhered to.
13. Unplug this product during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the product has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the product, the product has been
exposed to rain or moisture, does not operate nor-
mally, or has been dropped.
8. Do not install near any heat sources such as radia-
tors, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation . . . . . . . . . . . . . . . . . . . . . . .18
Contents
VCR Tape Playback . . . . . . . . . . . . . . . . . . . .18
Basic Instructions . . . . . . . . . . . . . . . . . . . . .18
Auto Tracking . . . . . . . . . . . . . . . . . . . . . . . .18
Manual Tracking . . . . . . . . . . . . . . . . . . . . . .18
Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Still Picture and Frame-by-Frame Playback .18
Slow Motion . . . . . . . . . . . . . . . . . . . . . . . . .18
CM SKIP (Commercial Skip) . . . . . . . . . . . . .19
VCR Tape Recording . . . . . . . . . . . . . . . .19-20
Basic Recording (One-Touch Recording) . . .19
Instant Timer Recording . . . . . . . . . . . . . . .19
Manual Timer Programming . . . . . . . . . . . . .20
Timer-Link Recording
(External Timer Recording) . . . . . . . . . . . . . .21
Copying from DVD to VCR . . . . . . . . . . . . . .22
On-Screen Display - VCR . . . . . . . . . . . . . . .22
Additional VCR Information . . . . . . . . . . . . .23
VCR Auto Play System . . . . . . . . . . . . . . . . .23
S-VHS Quasi Playback (SQPB) . . . . . . . . . .23
DVD Disc Playback (General Features) . . . .24
Introduction . . . . . . . . . . . . . . . . . . . . . .5
Moisture Condensation . . . . . . . . . . . . . . . . . .5
Symbol Used in this Manual . . . . . . . . . . . . . .5
About the
Symbol Display . . . . . . . . . . . . .5
Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . .5
Types of Playable Discs . . . . . . . . . . . . . . . . .6
Region Code . . . . . . . . . . . . . . . . . . . . . . . . . .6
Notes on Copyrights . . . . . . . . . . . . . . . . . . . .6
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Display Windows . . . . . . . . . . . . . . . . . . . . . . .7
Remote Control . . . . . . . . . . . . . . . . . . . . . . . .8
About the Remote Control . . . . . . . . . . . . . . .8
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Preparation . . . . . . . . . . . . . . . . . . . . . .10
Basic TV Connections . . . . . . . . . . . . . . . . . .10
Optional TV Connections . . . . . . . . . . . . . . .10
Cable/Satellite box Connection to unit . . . . .11
Accessory Audio/Video (A/V)
Additional Features . . . . . . . . . . . . . . . . . . . .25
Playing an Audio CD . . . . . . . . . . . . . . . . . . .26
Programmed Playback . . . . . . . . . . . . . . . . .26
Repeat Programmed Tracks . . . . . . . . . . . .26
Erasing a Track from Program List . . . . . . .26
Erasing the Complete Program List . . . . . .26
Viewing a JPEG file . . . . . . . . . . . . . . . . . . . .27
Slide Show . . . . . . . . . . . . . . . . . . . . . . . . .27
Still Picture . . . . . . . . . . . . . . . . . . . . . . . . .27
Moving to another File . . . . . . . . . . . . . . . .27
Connections to unit . . . . . . . . . . . . . . . . . . . .11
Connection to an Amplifier . . . . . . . . . . . . . .12
Initial Settings - VCR . . . . . . . . . . . . . . . . . . .13
General Operation . . . . . . . . . . . . . . . . . . . .13
CLOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Displaying Disc Information on-screen . . . .14
Initial Settings - DVD . . . . . . . . . . . . . . . .14-17
General Operation . . . . . . . . . . . . . . . . . . . .14
LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . . .15
• Menu Language . . . . . . . . . . . . . . . . . . .15
• Disc Audio/Subtitle/Menu . . . . . . . . . . . . .15
DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . .15
• TV Aspect . . . . . . . . . . . . . . . . . . . . . . . .15
• Display Mode . . . . . . . . . . . . . . . . . . . . . .15
• Progressive Scan . . . . . . . . . . . . . . . . . . .15
AUDIO . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
• Dolby Digital/DTS/MPEG . . . . . . . . . . . . .16
• Sample Freq. (Frequency) . . . . . . . . . . . .16
• Dynamic Range Control (DRC) . . . . . . .16
• Vocal . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
OTHERS . . . . . . . . . . . . . . . . . . . . . . . . . . .16
PBC . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
B.L.E. (Black Level Expansion) . . . . . . . . .16
Remote Control Function . . . . . . . . . . . . . . .17
Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Rotating the picture . . . . . . . . . . . . . . . . . .27
Playing a DVD VR format Disc . . . . . . . . . . .28
Maintenance and Service . . . . . . . . . . . . . . .28
Reference . . . . . . . . . . . . . . . . . . . . . . .29
Language Codes . . . . . . . . . . . . . . . . . . . . . .29
Troubleshooting . . . . . . . . . . . . . . . . . . . .30-31
Specifications . . . . . . . . . . . . . . . . . . . . . . . .32
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
To ensure proper use of this product, please read this
owner’s manual carefully and retain it for future
reference.
About the
Symbol Display
“
” may appear on your TV display during opera-
tion and indicates that the function is not permitted by
this unit or the disc.
This manual provides information on the operation
and maintenance of your unit. Should the unit require
service, contact an authorized service location.
Notes on Discs
Handling Discs
Moisture Condensation
Do not touch the playback side of the disc. Hold the
disc by the edges so that fingerprints do not get on
the surface. Never stick paper or tape on the disc.
Never operate the unit immediately after moving it
from a cold location to a warm location. Leave it
unplugged for two or three hours without operating it.
If you use the unit in such a situation, it may damage
discs/tapes and internal parts.
Symbol Used in this Manual
Note:
Indicates special notes and operating fea-
tures.
Storing Discs
After playing, store the disc in its case. Do not
expose the disc to direct sunlight or sources of heat
and never leave it in a parked car exposed to direct
sunlight.
Tip:
Indicates tips and hints for making the task
easier.
Cleaning Discs
A section whose title has one of the following
symbols is applicable only to the disc represented
by the symbol.
Fingerprints and dust on the disc can cause poor pic-
ture quality and sound distortion. Before playing,
clean the disc with a clean cloth. Wipe the disc from
the center out.
ALL
All discs listed below
DVD
DVD and finalized DVD±R/RW
VCD
Video CDs
ACD
Audio CDs
Do not use strong solvents such as alcohol, benzine,
thinner, commercially available cleaners, or anti-static
spray intended for older vinyl records.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes on Copyrights:
Types of Playable Discs
It is forbidden by law to copy, broadcast, show,
broadcast via cable, play in public, or rent copyright-
ed material without permission. This product features
the copy protection function developed by
DVD
(8 cm / 12 cm disc)
Video CD (VCD)
(8 cm / 12 cm disc)
Macrovision. Copy protection signals are recorded on
some discs. When recording and playing the pictures
of these discs picture noise will appear. This product
incorporates copyright protection technology that is
protected by method claims of certain U.S. patents
and other intellectual property rights owned by
Macrovision Corporation and other rights owners.
Use of this copyright protection technology must be
authorized by Macrovision Corporation, and is intend-
ed for home and other limited viewing uses only
unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is
prohibited.
Audio CD
(8 cm / 12 cm disc)
In addition, this unit plays DVD±R/RW, CD-
R/RW and SVCD, Dual disc that contains
audio titles, and/or JPEG files.
This indicates a product feature that is capable of
playing DVD-RW discs recorded with Video
Recording format.
Notice for Progressive Scan Use
Notes:
CONSUMERS SHOULD NOTE THAT NOT ALL
HIGH DEFINITION TELEVISION SETS ARE FULLY
COMPATIBLE WITH THIS PRODUCT AND MAY
CAUSE ARTIFACTS TO BE DISPLAYED IN THE
PICTURE. IN CASE OF 525 PROGRESSIVE SCAN
PICTURE PROBLEMS, IT IS RECOMMENDED
THAT THE USER SWITCH THE CONNECTION TO
THE ‘STANDARD DEFINITION’ OUTPUT. IF THERE
ARE QUESTIONS REGARDING YOUR TV SET
COMPATIBILITY WITH THIS MODEL 525p unit
RECORDER, PLEASE CONTACT OUR CUSTOMER
SERVICE CENTER.
• Depending on the conditions of the recording
equipment or the CD-R/RW (or DVD±R/RW) disc
itself, some CD-R/RW (or DVD±R/RW) discs
may not be played on the unit.
• Do not use irregularly shaped CDs (e.g., heart-
shaped or octagonal) since they may result in mal-
functions.
• This unit requires discs and recordings to meet cer-
tain technical standards in order to achieve optimal
playback quality. Pre-recorded DVDs are automati-
cally set to these standards. There are many differ-
ent types of recordable disc formats and these
require certain pre-existing conditions (see above)
to ensure compatible playback.
Regional Code
This unit has a regional code printed on the rear of
the unit. This unit can play only DVD discs labeled as
the same as the rear of the unit or “ALL”.
1 2
3 4
ALL
1 2
1
Notes on Regional Codes
• Most DVD discs have a globe with one or more
numbers in it clearly visible on the cover. This num-
ber must match your DVD player’s regional code or
the disc cannot play.
• If you try to play a DVD with a different regional
code from your player, the message “Check
Regional Code” appears on the TV screen.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Panel
a
b
c
d
Disc Tray (DVD deck)
Insert a disc here.
h
PAUSE (X)
Pause playback or recording. Press repeatedly for
frame-by-frame playback.
Cassette Compartment (VCR deck)
Insert a video cassette here.
i
j
k
l
m
n
OPEN/CLOSE (Z)
Opens or closes the disc tray.
POWER 1/:
Switches the unit ON and OFF.
Display Windows
Refer to below for details.
REW (m)
- DVD: Skip to beginning of current chapter or track,
press twice in quick successions to go to previous
chapter or track. Press and hold button for about two
seconds to search backward.
- VCR: Rewinds the tape during the stop mode or for
fast reverse picture search.
Remote Sensor
Point the unit Remote Control here.
EJECT (Z)
Ejects the tape in the VCR deck.
TRACKING -/+
To adjust tracking.
e
f
PLAY (N)
Starts playback of a disc or tape.
REC (z)
To record normally or to activate One-touch Timer
Recording by repeated presses.
Press REC (z) for more than 3 seconds to set the
unit to standby mode for Timer-Link recording.
FF (M)
- DVD: Skip to next chapter or track. Press and hold
for two seconds for a fast forward search.
- VCR: Advances the tape during the STOP mode or
for fast forward picture search.
o
p
VCR/DVD (output select)
Select one of your output sources to view on the TV
screen between DVD and VCR.
g
STOP (x)
Stops playback of the disc or tape.
LINE2 (VIDEO/AUDIO (L/R) input)
Connect to the audio/video output of an external
source (Audio system, TV/Monitor, Another VCR).
Display Windows
The DVD deck is selected.
A cassette is in the VCR deck.
DVD
A disc is in the DVD deck.
(Lights when a disc is in the DVD deck
and Flashes when no disc.)
The VCR deck is selected.
VCR
REC
PM
The unit is Recording. (VCR part only)
Indicates PM time. (AM is not displayed.)
Indicates when the Progressive scan is active.
Indicates repeat mode.
[P]
Indicates total playing time, elapsed time,
remaining time or current deck status
(Playback, Pause, etc).
The unit is in timer recording or a timer recording
is programmed (VCR part only).
This indicator will flash when the unit is set to
standby mode for Timer-Link recording.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control
b / B / v / V : Selects menu options.
TRACKING (-/+) : Adjusts manually the tape’s picture
onscreen.
SETUP/MENU : Accesses or removes DVD Setup menu
and VCR menu.
ENTER (OK) : Confirms menu selections. Displays func-
tions on the TV screen.
a
RETURN (O) : Removes the setup menu.
ꢀ ꢀ ꢀ ꢀ ꢀ b ꢀ ꢀ ꢀ ꢀ ꢀ
X (PAUSE/STEP) :
Pause playback or recording temporarily.
Press repeatedly for frame-by-frame playback.
./> (SKIP) (DVD only):
Go to next the chapter or track.
Returns to beginning of current chapter or track or go to
previous chapter or track.
b
c
x (STOP) : Stops playback or recording.
m (REW) / M (FF):
- DVD: Search backward or forward.
- VCR: Rewinds/Advances the tape during the STOP mode,
for fast backward/forward picture search.
N (PLAY) : Starts playback.
0-9 Selects numbered options in a menu.
PROGRAM : Shows or hides Program menu.
CLEAR (0000) : Removes a mark on the Marker Search
menu.
ꢀ ꢀ ꢀ ꢀ ꢀ c ꢀ ꢀ ꢀ ꢀ ꢀ
A.MONITOR : Selects an audio language (DVD).
SUBTITLE : Selects a subtitle language.
ANGLE : Selects a DVD camera angle, if available.
ZOOM : Enlarges DVD video image.
RM-SHRXVC11A
MARKER : Marks any point during playback.
SEARCH : Displays Marker Search menu.
TITLE : Displays the disc’s Title menu, if available.
z (REC) : Starts recording.
ꢀ ꢀ ꢀ ꢀ ꢀ a ꢀ ꢀ ꢀ ꢀ ꢀ
1/I (POWER) : Switches unit ON and OFF.
: This button is not available.
*
Z (OPEN/CLOSE) : Opens and closes the disc tray.
DVD : Select the unit function mode to DVD.
REPEAT : Repeat chapter, track, title or all.
RANDOM : Plays tracks in random order.
VCR : Select the unit function mode to VCR.
: Fast forwards picture search through 30 seconds of
recording.
AUX : Selects the VCR deck’s source (LINE 1 or LINE 2).
DISPLAY : Accesses On-Screen Display.
Switches between the clock, tape counter and tape
remaining modes on the display.
REPEAT A-B : Repeats sequence between two points (A
and B).
SPEED : Selects recording speed. Shows tape playing
speed.
DISC MENU : Accesses menu on a DVD disc.
About the Remote Control
Operation Range
Battery installation
Detach the battery cover on the rear of
the Remote Control, and insert two
(R03/AAA) size batteries with 3 and #
aligned correctly.
Point the Remote Control at the remote sensor and
press the buttons.
Distance: About 23 ft (7 m) from the front of the
remote sensor.
Do not mix old and new batteries and never
mix different types of batteries such as
standard, alkaline, etc.
Angle:
About 30° in each direction of the front of
the remote sensor.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Panel
Caution
Do not touch the inner pins of the jacks on the rear panel.
Electrostatic discharge may cause permanent damage to the unit.
a b c d
e
f
a
VCR IN LINE 1 (VIDEO/AUDIO (Left/Right))
Connect the audio/video output of an external source
(Cable/Satellite box, Audio system, TV/Monitor, VCR,
Camcorder).
e
f
AC Power Cord
Plug into the power source.
COAXIAL (DIGITAL AUDIO OUT jack)
(DVD EXCLUSIVE OUT)
Connect to digital (coaxial) audio equipment.
b
c
DVD/VCR OUT (VIDEO/AUDIO (Left/Right))
Connect to a TV with video and audio inputs.
.
COMPONENT/PROGRESSIVE SCAN VIDEO
OUT (Y Pb Pr) (DVD EXCLUSIVE OUT)
Connect to a TV with Y Pb Pr inputs.
d
AUDIO OUT (Left/Right)
(DVD EXCLUSIVE OUT)
Connect to a TV or other equipment with audio inputs.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation
Depending on your TV and other equipment
there are various ways you can connect the
player. Please refer to the manuals of your
TV, VCR, stereo system or other devices as
necessary for additional connection
information.
Audio/Video connection
1. Connect the DVD/VCR VIDEO OUT jack on the
unit to the video in jack on the TV using the video
cable supplied (V).
2. Connect the Left and Right DVD/VCR AUDIO
OUT jacks on the unit to the audio left/right in
jacks on the TV using the supplied audio cables
(A1).
Notes:
•
The picture and sound of a nearby TV, VCR, or
radio may be distorted during playback. Position
the units away from each other or turn off the unit
after removing the disc.
Note:
If you use this connection, set the TV’s source selec-
tor to VIDEO.
•
Do not connect the unit’s AUDIO OUT jack to the
phono in jack (record deck) of your audio system.
Do not connect the unit via another VCR. The
DVD image could be distorted by the copy protec-
tion system.
Optional TV Connections
These connections support only DVD playback. The
VCR still output through the DVD/VCR OUT (A1, V)
jacks.
Basic TV Connections
Component Video / Progressive Scan
connection
Make one of the following connections, depending on
the capabilities of your TV.
If your television is a high-definition or “digital ready”
television, you may take advantage of the unit’s pro-
gressive scan output for the highest possible video
resolution.
Rear of TV
VIDEO
INPUT
AUDIO INPUT
R
L
Connect the COMPONENT/PROGRESSIVE SCAN
VIDEO OUT jacks on the unit to the corresponding
jacks on the TV using an optional Y Pb Pr cable (C).
V
A1
Audio connection
Rear of DVD+VCR
Connect the Left and Right AUDIO OUT jacks of the
unit to the audio left/right in jacks on the TV using the
supplied audio cables (A2).
Note:
If you connect both composite and component jacks
to TV, the picture may be unstably on the TV. You
could disconnect one of them to solve this problem.
C
A2
Y
Pr
Pb
R
L
COMPONENT/PROGRESSIVE SCAN
VIDEO INPUT
AUDIO INPUT
Rear of TV
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable/Satellite box Connection
to unit
Accessory Audio/Video (A/V)
Connections to unit
To use Timer-Link Recording, connect the VCR IN
LINE 1 jacks on the unit to the audio/video out jacks
on your Cable/Satellite box, using the optional
audio/video cables.
Connect the VCR IN LINE 1 or LINE 2 jacks on the
unit to the audio/video out jacks on your accessory
component, using the optional audio/video cables.
(Refer to page 19 for “Basic Recording”.)
(Refer to page 21 for “Timer-Link Recording”.)
Cable/Satellite box
AUDIO OUT
VIDEO
OUT
Rear of the unit
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection to an Amplifier
Rear of the unit
You can only listen to DVD playback using COAXIAL
(X) and AUDIO OUT (A2) connections. The VCR will
still be heard through the DVD/VCR AUDIO OUT (A1)
jack.
Connecting to an amplifier equipped with two
channel analog stereo or Dolby Pro Logic II/Pro
Logic
A1
A2
X
Connect the Left and Right AUDIO OUT (or
DVD/VCR AUDIO OUT) jacks on the unit to the audio
left and right in jacks on your amplifier, receiver, or
stereo system using the audio cables (A1, A2)
supplied.
R
L
COAXIAL
AUDIO INPUT
DIGITAL INPUT
Amplifier (Receiver)
Connecting to an amplifier equipped with two chan-
nel digital stereo (PCM) or to an Audio/Video receiv-
er equipped with a multi-channel decoder (Dolby
Digital™, MPEG 2, or DTS)
Manufactured under license from Dolby
Laboratories. Dolby and the double-D
symbol are registered trademarks of Dolby
Laboratories.
1. Connect one of the unit’s DIGITAL AUDIO OUT
jacks (COAXIAL X) to the corresponding jack on
your amplifier. Use an optional digital (COAXIAL
X) audio cable.
“DTS” and “DTS Digital Out” are registered
trademarks of DTS, Inc.
2. You will need to activate the unit’s digital output.
(See “AUDIO” on page 16).
Digital Multi-channel sound
A digital multi-channel connection provides the best
sound quality. For this you need a multi-channel
Audio/Video receiver that supports one or more of the
audio formats supported by your unit (MPEG 2, Dolby
Digital and DTS). Check the receiver manual and the
logos on the front of the receiver.
Caution
Due to the DTS Licensing agreement, the digital
output will be in DTS digital out when DTS audio
stream is selected.
Notes:
•
If the audio format of the digital output does not
match the capabilities of your receiver, the receiv-
er will produce a strong, distorted sound or no
sound at all.
•
•
Six Channel Digital Surround Sound via digital
connection can only be obtained if your receiver is
equipped with a Digital Multi-channel decoder.
To see the audio format of the current DVD in the
on-screen display, press A.MONITOR.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP
Initial Settings - VCR
By using the VCR Setup menu, you can make
various adjustments to items such as clock setting,
and timer recordings.
Your unit allows remote control adjustment of several
features.
General Operation
1. Press VCR on the Remote Control.
2. Press SETUP MENU and the MAIN menu will
appear.
FUNCTION OSD
The on-screen display can be turned on or off.
AUDIO MODE
The unit has two separate audio playback systems,
the high quality VHS Hi-Fi system and standard
NORMAL mono system. The same audio is generally
recorded on both systems. The VHS Hi-Fi system
plays on separate (left and right) channels, and the
NORMAL system plays monaural sound. The normal
track is always played so the cassette can be played
on a unit that does not have VHS Hi-Fi.
3. Use v/V to select the desired menu, then press
ENTER (OK).
4. Use v/V to choose a desired option on the select-
ed Menu. Then use b/B to choose a desired
setting.
AUDIO OUTPUT (STEREO/LEFT/RIGHT)
Used during playback [when AUDIO MODE
(HI-FI/NORMAL) is in HI-FI position] for selecting the
audio output signals from the AUDIO OUT terminals
(L ch and R ch). This display setting should normally
be left in the stereo position, so that when a stereo
tape is played, the stereo sound will be heard
through the left and right channels. If a mono tape is
played and the audio output is set to stereo, the
same mono sound will be heard from both left and
right channels.
5. Press SETUP MENU when finished.
Note:
Menus remain on-screen for 3 minutes.
CLOCK
Use v/V/b/B to enter the necessary information.
• MONTH : Choose the month.
• DAY : Choose the date.
The day of the week will display automatically.
• YEAR : Choose the year.
• TIME : Choose the time.
Press and hold b/B to advance clock continuously.
Note:
The clock uses the 12-hour system. Be sure to set
AM and PM correctly.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Displaying Disc Information
on-screen
You can display various information about the disc
Initial Settings - DVD
By using the Setup menu, you can make various
adjustments to items such as picture and sound. You
can also set a language for the subtitles and the
Setup menu, among other things. For details on each
Setup menu item, see pages 15 to 16.
loaded on-screen.
1. Press DISPLAY to show various playback
information.
To display and exit the Menu:
The displayed items differ depending on the disc
type or playing status.
Press SETUP MENU to display the menu. A second
press of SETUP MENU will take you back to initial
screen.
To go to the next level:
Press B on the Remote Control.
To go back to the previous level:
Press b on the Remote Control.
General Operation
1. Press DVD button.
2. Press SETUP MENU. The Setup menu appears.
2. You can select an item by pressing v / V and
change or select the setting by pressing b / B.
LANGUAGE
English
Original
Original
Original
Menu Language
Disc Audio
•
Title (Track) – Current title (or track).
number/total number of titles (or tracks).
Chapter – Current chapter number/total num-
ber of chapters.
Disc Subtitle
Disc Menu
•
•
•
•
•
Time – Elapsed playing time.
Audio – Selected audio language or channel.
Subtitle – Selected subtitle.
Angle – Selected angle/total number of
angles.
Move
Select
3. Use v / V to select the desired option then press
B to move to the second level. The screen shows
the current setting for the selected item, as well
as alternate setting(s).
Note:
If no button is pressed for a few seconds, the on-
screen display disappears.
4. Use v / V to select the second desired option
then press B to move to the third level.
5. Use v / V to select the desired setting then press
ENTER (OK) to confirm your selection. Some
items require additional steps.
6. Press SETUP MENU or N (PLAY) to exit the
Setup menu.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
DISPLAY
LANGUAGE
DISPLAY
LANGUAGE
16:9
English
Original
Original
Original
TV Aspect
Menu Language
Disc Audio
Display Mode
Progressive Scan
Widescree
Off
Disc Subtitle
Disc Menu
Move
Select
Move
Select
TV Aspect
Menu Language
Select a language for the Setup menu and on-screen
display.
4:3 – Select when a standard 4:3 TV is connected.
16:9 – Select when a 16:9 wide TV is connected.
Disc Audio / Subtitle / Menu
Display Mode
Select the language you prefer for the audio track
(disc audio), subtitles, and the disc menu.
The display Mode setting works only when the TV
Aspect mode is set to “4:3”.
Original – Refers to the original language in
which the disc was recorded.
Letterbox – Displays a wide picture with bands
on the upper and lower portions of the screen.
Other – To select another language, press num-
ber buttons then ENTER (OK) to enter the corre-
sponding 4-digit number according to the lan-
guage code list on page 30. If you enter the
wrong language code, press CLEAR (0000).
Panscan – Automatically displays the wide pic-
ture on the entire screen and cuts off the portions
that do not fit.
Progressive Scan
Progressive Scan Video provides the highest quality
pictures with less flickering.
If you are using the Component Video jacks for con-
nection to a TV or a monitor that is compatible with a
progressive scan signal, set Progressive Scan to On.
To Turn ON progressive scan:
Connect component video out of the this unit to the
input of your monitor/television, set your television or
monitor to Component Input.
1. Select “Progressive Scan” on the DISPLAY menu
then press B.
2. Select “On” using the v / V buttons.
3. Pressing ENTER (OK) will set the player to
Progressive scan mode.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
AUDIO
OTHERS
OTHERS
Each DVD disc has a variety of audio output options.
Set the player’s AUDIO options according to the type
of audio system you use.
PBC
On
On
B.L.E.
AUDIO
Dolby Digital
DTS
Bitstream
Bitstream
PCM
MPEG
Sample Freq.
DRC
48 kHz
On
Move
Select
Vocal
Off
PBC VCD
Move
Select
Set Playback Control (PBC) to On or Off.
Dolby Digital / DTS / MPEG
On: Video CDs with PBC are played according to the
PBC.
Bitstream – Select “Bitstream” if you connect this
DVD player’s DIGITAL OUT jack to an amplifier or
other equipment with a Dolby Digital, DTS or
MPEG decoder.
Off: Video CDs with PBC are played the same way
as Audio CDs.
PCM (for Dolby Digital / MPEG) – Select when
connected to a two-channel digital stereo amplifi-
er. DVDs encoded in Dolby Digital or MPEG will
be automatically downmixed to two-channel PCM
audio.
B.L.E. (Black Level Expansion)
To select the black level of playback pictures. Set
your preference and monitor’s ability.
On: Expanded grey scale. (0 IRE cut off)
Off: Standard grey scale. (7.5 IRE cut off)
Off (for DTS): If you select “Off”, the DTS signal
is not output through the DIGITAL OUT jack.
Sample Freq. (Frequency)
If your receiver or amplifier is NOT capable of han-
dling 96 kHz signals, select 48 kHz. When this choice
is made, this unit automatically converts any 96 kHz
signals to 48 kHz so your system can decode them.
If your receiver or amplifier is capable of handling 96
kHz signals, select 96 kHz.
Check the documentation for your amplifier to verify
its capabilities.
Dynamic Range Control (DRC)
With the DVD format, you can hear a program’s
soundtrack in the most accurate and realistic presen-
tation. However, you may wish to compress the
dynamic range of the audio output (the difference
between the loudest sounds and the quietest ones).
This allows you to listen to a movie at a lower volume
without losing clarity of sound. Set DRC to On for this
effect.
Vocal
Set to On only when a multi-channel karaoke DVD is
playing. The karaoke channels on the disc mix into
normal stereo sound.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control Function
Remote Control A/B/C Code Switching
The remote control is capable of controlling three
JVC video units independently. Each of the units can
respond to one of three codes (A, B or C). The
remote control is preset to send C code signals
because your unit is initially set to respond to C code
signals. You can easily modify your unit to respond to
A or B code signals.
1/ I
B
ENTER
x
1-3
RM-SHRXVC11A
•
Keep pressing ENTER (OK) down during step 1.
1. Press the number Key “1” for A, “2” for B or
“3” for C to change the remote control code.
2. Ensure the unit in VCR mode, and then turn off
the power.
3. Press B on the unit for over 5 seconds while the
unit is turned off. The code currently set appears
on the front display panel.
4. Press x (STOP) on the remote control to change
the unit's code. The code currently set on the
remote control blinks on the front display panel for
approximately 5 seconds, and is applied to the
unit.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
This chapter describes how to operate the VCR and
DVD.
Search
This function lets you visually search for a tape sec-
tion in either direction: forward and backward. During
the high-speed picture search modes, the audio is
muted and horizontal lines (noise bars) appear. Also,
a short time is needed to stabilize the tape speed
when re-entering the PLAY mode so slight interfer-
ence may be observed during this time.
VCR Tape Playback
Press the VCR button to select the device to be oper-
ated.
Basic Instructions
To search:
1. Turn on the TV.
1. Press m (REW) or M (FF) during playback.
Press and hold m (REW) or M (FF) during
tape fast winding.
2. Direct VIDEO/AUDIO connection is made
between the unit and the TV, set the TV’s source
selector to VIDEO.
2. To return to playback, press N (PLAY).
3. Insert a pre-recorded video cassette.
Note:
The
automatically.
indicator lights and the unit powers on
After 3 minutes in SEARCH mode the unit returns to PLAY
mode to protect the tape and video heads.
4. If a tape without a safety tab is inserted the unit
starts playback automatically.
If not, press N (PLAY).
Still Picture and Frame-by-Frame Playback
1. Press X (PAUSE) during playback.
A still picture appears on the TV screen and the
audio is muted.
5. Press x (STOP) to stop playback. If the tape
reaches the end before you press x (STOP) the
unit automatically stops, rewinds and ejects the
tape and unit power is off.
2
If the still picture vibrates vertically, stabilize it by
using v/V (-/+) on the Remote Control.
6. Fast wind tape:
Press m (REW) or M (FF) during stop.
3. Press X (PAUSE) repeatedly to advance the
video picture one frame at a time.
Note:
It is not necessary to select the tape speed for play-
back because it is automatically selected by the unit.
4. To return to playback, press N (PLAY).
Note:
Auto Tracking
After 5 minutes in STILL mode the unit stops to protect the
tape and video heads.
Automatic tracking adjusts the picture to remove
snow or streaks and beings when:
Slow Motion
•
•
•
A tape is played for the first time.
1. While in still mode, press M (FORWARD).
The tape is played at a speed 1/19 times slower
than the normal speed.
The tape speed (SP, LP, SLP) changes.
Streaks or snow appear due to scratches on the
tape.
2. Use v/V (-/+) on the Remote Control if necessary
to adjust the tracking.
Manual Tracking
3. To return to the normal speed, press N (PLAY).
To manually adjust the tracking use the v/V (-/+)
buttons on the Remote Control during playback.
Notes:
•
During slow motion, audio is muted and horizontal
lines (noise bars) may appear on the TV screen.
This is normal.
Notes:
•
•
Vertical jitter requires a very fine adjustment.
Tracking is automatically reset to normal when the tape
is ejected or the power cord is unplugged for more than
3 seconds.
•
After 3 minutes in SLOW MOTION mode the unit
goes back to PLAY mode to protect the tape and
video heads.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
CM SKIP (Commercial Skip)
Instant Timer Recording
This feature is useful for skipping commercials or
short program segments.
With this feature you can record for a preset length
without using the program timer.
1. Press
in playback mode.
Note:
The unit performs a fast forward picture search
through 30 seconds of recording.
Instant Timer recording is not available when the
external timer record is in progress.
2. Press
again to extend the search time by an
addition 30 seconds. The maximum search time is
3 minutes.
1. Turn on unit and the TV.
2. Insert a video cassette with the safety tab intact.
3. When the search is complete, the unit goes into
playback mode automatically.
3. If you are recording from another source via
audio/video input jacks (at the rear or front panel).
4. Connect the LINE1 or LINE2 input jacks on this
unit to the AUDIO/VIDEO OUTPUT jack on the
external device using the audio/video cables.
VCR Tape Recording
Basic Recording (One-Touch Recording)
5. Select LINE1 (rear jacks) or LINE2 (front jacks) by
using AUX.
You can record from an external component, such as
a camcorder or VCR, connected to any of the unit’s
external inputs.
6. Set the desired recording speed (SP or SLP) using
SPEED. The tape speed appears on the TV screen.
7. Press z (REC) twice. The menu appears on the
1. Make sure that the component you want to record
from is connected properly to the unit. See page 11.
TV screen, recording starts, and the
indicator lights.
(TIMER)
2. Press AUX repeatedly to select the external input
to record from.
INSTANT TIMER RECORD
•
LINE1 (L1): Audio/Video Input mounted on
back panel.
INPUT
LINE1
SP
SPEED
•
LINE2 (L2): Audio/Video Input mounted on
front panel.
START
NOW
LENGTH
0H30M
3. Load a recordable tape.
8. Press z (REC) repeatedly to select the recording
time length. Each time you press this button the
recording time increases 30 minutes (up to 9
hours). At the end of the recording, the unit will
stop recording and shut off.
4. Set a recording mode (SP or SLP) as necessary
by pressing SPEED repeatedly.
5. Play the tape or disc in the external component.
If you have a TV attached to your unit, you can
see the video playing.
If you set the time to 0H00M, the unit goes into
the normal recording mode.
6. Press z (REC) once to start recording.
The REC indicator lights in the display window.
9. Press x (STOP) to stop the recording.
7. Press x (STOP) to stop recording.
Notes:
Checking the Recording Time
•
•
Before recording, confirm the recording start position.
Press z (REC) once to check the recording time.
The recalled setting automatically returns to the TV
screen after 6 seconds.
If your source is copy-protected using CopyGuard,
you will not be able to record it using this unit.
See Copyright on page 6 for more details.
•
To record for a fixed length of time, see Instant
Timer Recording.
Extending the Recording Time
The recording time can be extended anytime by
pressing z (REC). Subsequent presses result in
advancing the recording time by 30-minute increments.
To pause the recording
1. Press X (PAUSE) to pause the tape during
recording. The REC indicator flashes in the
display window.
Note:
If you press X (PAUSE) during instant timer record-
ing, the instant timer recording is cancelled. It goes to
normal recording PAUSE mode.
2. When you want to continue recording, press
X (PAUSE) or press z (REC).
After 5 minutes in PAUSE mode, the unit stops
automatically to protect the tape and the video
heads.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
•
If the power fails or the unit is unplugged the
clock and timer settings are kept in memory for
only 3 seconds. Otherwise you must reset the
clock and timer.
Manual Timer Programming
1. Press SETUP MENU and the main menu
appears.
•
•
If the tape indicator is blinking, no tape is loaded.
2. Use v / V to choose the PROGRAM option and
press ENTER (OK).
When you are playing DVD at programmed
Recording time, the unit automatically change to
VCR mode and start recording.
•
The unit will automatically power off when Timer
Recording ends.
Checking or Erasing the Timer Program
If eight programs are already entered, the FULLY
PROGRAMMED message appears for a moment
and then PROGRAM 1 appears on the TV
screen.
Programming can be checked whenever the unit is
turned on.
1. Press SETUP MENU and the main menu appears.
3. Use the v / V buttons to switch between the
program options, and the b / B buttons to input
the program information:
2. Use v / V to choose the PROGRAM menu and
press ENTER (OK).
Input the MONTH, DAY, START and STOP times
of the program you want to record.
INPUT: Select a LINE1 or LINE2.
SPEED: AUTO mode determines how much tape
is left and switches the speed from SP to SLP if it
is necessary to complete recording the program.
If this occurs there could be some picture and
sound distortion at the point where the speed
changes.
3. Use b / B to select a program you want to check or
erase. To erase the program, press CLEAR (0000).
4. Press SETUP MENU to return to the TV screen.
REPEAT: To record up to 8 programs on a certain
day of every week select WEEKLY. To record up
to 8 programs at the same time Monday through
Friday select DAILY. Otherwise select ONCE.
Program Priority
If the recording start and end times of preset pro-
grams overlap on the same day (see the example),
the second program is not recorded until the first is
finished.
4. Press SETUP MENU and the program is
memorized by the unit.
5. Additional programs may be entered by repeating
steps 1-4.
Notes:
•
Ensure you insert a tape with the record safety
tab intact before the first programmed time.
•
•
Press x (STOP) to end timer recording.
If you make a mistake or want to change a set-
ting, use v to select the option and correct it
using b / B.
In this example, the first part of program numbers 2
and 3 are not recorded.
•
•
If the program preset time is past, the “PAST
TIME PROGRAMMED” message appears on the
TV screen. Return to the incorrect program and
program it with the correct time.
If you enter a past date, the timer recording will
be performed on that date of the next year.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
•
The external timer record will be set to off
automatically when:
- There is no recordable tape.
Timer-Link Recording
(External Timer Recording)
- STOP or PAUSE button is pressed while
external timer recording.
- The power of this unit is ON in the external
timer record standby mode.
If the external device such as Cable/Satellite box that
is connected to this unit has the timer reservation
function, this unit can record the input signal from
external device via the timer LINE1 jack.
- When you press the z (REC) for more than
3 seconds again in the external timer record
standby mode.
1. Connect the LINE1 input jacks on this unit to the
AUDIO/VIDEO OUTPUT jack on the external
device using the audio/video cables.
Program Priority
If the recording time of this unit and the external
device are overlap:
The earlier program takes priority. When the earlier
program finishes, the later program starts.
2. Set the timer reservation setting of the external
device.
3. Turn off the external device.
4. Insert a video cassette with the safety tab intact to
this unit. Select the recording speed with remote.
Timer Link record
5. Press z (REC) for more than 3 seconds on the
front panel when the unit power is off.
Timer Record of this unit
The " " mark will flashes on the display window.
This unit is set to standby mode for Timer-Link
recording.
Notes:
•
•
•
If the power of the external device is on by the
timer reservation setting, this unit detects the
signals of external device and start the
recording automatically.
If the power of the external device is off during
external timer recording, this unit will be stop
the external timer recording and turns off the
power automatically.
If the power of the external device is on again,
this unit will be start the external timer record-
ing again.
•
•
Press x (STOP) to stop recording intentionally
while external timer recording is in progress.
The external timer record is available only for
the device that is connected with LINE1 jack
on this unit.
•
Your external device such as Cable/Satellite
box might keep running Audio/Video signals
through the OUTPUT jack, even if the unit is
powered off. If so, Timer-Link recording
doesn’t work.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Each press of the ENTER (OK) changes the TV
screen in the following sequence.
Copying from DVD to VCR
You can copy the contents of a DVD to a VHS tape.
STOP
SP
1. Insert the disc you wish to copy into the DVD
deck and close the disc tray.
JAN 1 , MON
2:15 PM
2. Insert a blank VHS video tape into the VCR deck.
2:15 PM
3. Find the place on the DVD from which you want
to start dubbing using the PLAY, FF, REW and
PAUSE functions.
0:35:40
REM 1:58
For best results, pause playback at the point from
which you want to record.
Real-Time Counter
4. Press the z (REC). The DVD goes into PLAY
mode and the VCR goes into RECORD mode. If
the DVD disc menu appears, you may need to
press N (PLAY) manually to begin copying.
If a tape with contents recorded on it is inserted into
the VCR, the real-time counter shows length of the
tape running in hours, minutes, and seconds. Press
DISPLAY to select the real-time counter display.
Every press of DISPLAY changes the TV screen as
illustrated below.
5. Press X (PAUSE) during dubbing pauses both
DVD play and VCR record functions.
Press X (PAUSE) again or press z (REC) or
N (PLAY), the dubbing is resuming.
2:15 AM
CLOCK
0:05:25
COUNTER
REM 1:07
REMAINING TIME
6. During dub PAUSING, you could find the wanted
place in the disc for dubbing by using the FF,
REW and SKIP search functions.
Counter Memory
This feature is useful if there is a section of tape you
want to view immediately after recording or if you
want to return to the same point several times.
7. When the DVD is finished playing, press
x (STOP) to end copying.
1. Begin recording or playing a tape.
Caution
2. Press DISPLAY until the real-time counter is dis-
played on the TV screen.
Do not use FF, REW and SKIP search functions dur-
ing dubbing; otherwise you might record the unwant-
ed video with no sound from disc.
3. At the point that you want to locate later, reset the
real-time counter to “0:00:00” by pressing CLEAR
(0000).
Notes:
4. Continue to play or record.
•
You must stop the copy process manually when
the DVD movie ends, or the unit may replay and
record over and over again.
5. Press x (STOP) when recording or playback fin-
ishes.
6. Press m (REW). The tape automatically stops
when the tape counter returns to about “0:00:00”.
•
•
When you stop the DVD playback during copying,
the recording on VCR is stopped automatically.
Tape Remaining
This function displays the amount of time remaining
on the tape during recording or playback.
Press DISPLAY repeatedly until the REM indicator
displays on the TV screen during recording or play-
back. The remaining tape length may not be dis-
played correctly depending on the condition of the
tape and the kind of the tape (T-140, T-160, or T-210
etc.).
If the DVD disc is copy-protected, you will not be
able to copy it using this unit.
On-Screen Display - VCR
Some of these functions will be displayed every time
the unit is operated.
❶
❷
Notes:
PLAY
SP
•
•
•
The function displays can be seen displayed on
the TV screen for 5 seconds.
The clock (or tape counter, tape remaining) mode
will be displayed until you press ENTER (OK).
The tape counter and the remaining tape length
indicator appear only when a cassette is inserted.
Also, the remaining tape length indicator appears
after any tape operation.
JAN 1 , TUE
2:15 PM
❸
❹
❶
❷
TAPE SPEED DISPLAY
FUNCTION DISPLAY
❸
❹
DATE DISPLAY
CLOCK/ COUNT/
REMAIN DISPLAY
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional VCR Information
•
During manual recording playback, or fast forward
modes, the unit automatically starts rewinding the
tape at the end of the tape. The cassette stops at
the beginning of the tape and is ejected.
•
After you have finished using the unit, rewind,
eject, and remove the cassette. Place the cas-
sette in its protective sleeve to protect it from
dust. It is not necessary to rewind the cassette
before removing it, but if you do, it is ready to play
or record the next time you use it.
•
Do not attempt to hook up more than one televi-
sion set to the unit for either recording or
playback.
VCR Auto Play System
This unit features automatic playback.
When you load a tape with the safety tab removed
the following occurs:
•
•
•
•
The Output Source is changed to VCR mode
automatically.
The power turns on automatically and playback
begins.
At the end of the tape, the unit stops, then
rewinds.
The tape is ejected after rewinding and the turns
itself off automatically.
Note:
Auto power off does not function during regular DVD
play mode. (unit power stays on.)
S-VHS Quasi Playback (SQPB)
•
This unit can playback S-VHS recorded tapes;
however, it cannot record in S-VHS format, but
VHS format only.
•
SQPB is an abbreviation for S-VHS Quasi
Playback.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD Disc Playback (General Features)
Buttons
Operations
Discs
ALL
Z (OPEN / CLOSE)
X (PAUSE)
Opens or closes the disc tray.
ALL
During playback, press X to pause playback.
Press X repeatedly to play Frame-by-Frame.
DVD
VCD
. / > (SKIP)
m / M (REW/FF)
During playback, press . or > to go to the next
chapter/track or to return to the beginning of the current
chapter/track.
ALL
ACD
DVD
Press . twice briefly to step back to the previous
chapter/track.
ACD
VCD
VCD
During playback, press m or M repeatedly to select
the required scan speed.
DVD; 4 steps
Video CD, Audio CD ; 3 steps
DVD
ALL
While the playback is paused, press M repeatedly to
play in slow motion (4 steps).
REPEAT
During playback, press REPEAT repeatedly to select a
desired repeat mode.
DVD discs: Chapter/Title/Off
Video CD, Audio CD : Track/All/Off
REPEAT A-B
ZOOM
Press the REPEAT A-B button one at time to select a
point A and point B and repeats a sequence from point
A (Starting point) to point B (End point).
DVD
DVD
VCD
VCD
ACD
During playback or pause mode, press ZOOM to
enlarge the video image (3 steps).
You can move through the zoomed picture using b B v
V buttons. Press CLEAR (0000) to exit.
RANDOM
TITLE
During playback or in stop mode, press RANDOM for
random playback.
ACD
DVD
If the current DVD title has a menu, the title menu
appears on the screen. Otherwise, the disc menu may
appears.
DISC MENU
ANGLE
The disc menu appears on the screen.
DVD
DVD
During playback of DVD disc that contains scenes
recorded at different camera angles, press ANGLE
repeatedly to select a desired angle.
SUBTITLE
During playback, press SUBTITLE repeatedly to select a
desired subtitle language.
DVD
DVD
A.MONITOR
During playback, press A.MONITOR repeatedly to hear
a different audio language or audio track.
VCD
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes on general features:
Last Scene Memory DVD
VCD
• If you press > once during Repeat Chapter
(Track) playback, the repeat playback cancels.
This player memorizes last scene from the last disc
that is viewed. The last scene remains in memory
even if you remove the disc from the player or switch
off the player. If you load a disc that has the scene
memorized, the scene is automatically recalled.
• Zoom may not work on some DVDs.
• When you are playing a DVD disc that contains
scenes recorded different camera angles, the angle
indicator will blink on the TV screen during the
operations as an indication that angle switching is
possible.
Note:
This player does not memorize the scene of a disc if
you switch off the player before commencing to play
the disc.
• The A-B repeat function is available only in the
current track.
Screen Saver
Additional features
The screen saver appears when you leave the unit in
Stop mode for about five minutes.
Time Search DVD
VCD
To start playing at any chosen time on the disc:
1. Press DISPLAY during playback.
2. Press v / V to select the time clock icon and
“--:--:--” appears.
3. Input the required start time in hours, minutes,
and seconds from left to right. If you enter the
wrong numbers, press CLEAR (0000) to remove
the numbers you entered. Then input the correct
numbers.
4. Press ENTER (OK) to confirm. Playback starts
from the selected time.
Marker Search DVD
To enter a Marker
VCD
You can start playback from up to nine memorized
points. To enter a marker, press MARKER at the
desired point on the disc. The Marker icon appears
on the TV screen briefly. Repeat to enter up to nine
markers.
To Recall or Clear a Marked Scene
1. During disc playback, press SEARCH. The marker
search menu appears on the screen.
2. Within 10 seconds, press b / B to select a marker
number that you want to recall or clear.
3. Press ENTER (OK) and playback starts from the
marked scene. Or, Press CLEAR (0000) and the
marker number is erased from the list.
4. You can play any marker by inputting its number
on the marker search menu.
5. Press x (STOP) twice, clear all markers.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Repeat Programmed Tracks
Playing an Audio CD
Press REPEAT to select a desired repeat mode.
This unit can play Audio CDs.
• Track: repeats the current track
• All: repeats all the tracks on programmed list.
• Off(No display): does not play repeatedly.
Audio CD
Once you insert an Audio CD, a menu appears on
the TV screen.
Note:
Press v / V to select a track/file then press N
(PLAY) or ENTER (OK) and playback starts. You can
use variable playback functions. Refer to page 24-25.
If you press > once during Repeat Track playback,
the repeat playback cancels.
Erasing a Track from “Program” List
1. During STOP mode, press PROGRAM and
E
the
mark will appear.
2. Use v V b B to select the track that you wish to
erase from the Program list.
3. Press CLEAR (0000). Repeat step 1~3 to erase
additional tracks on the list.
Erasing the Complete Program List
1. During STOP mode, press PROGRAM and
Programmed Playback
E
the
mark will appear.
2. Use v V b B to select “Clear All”, then press
ENTER (OK).
The program function enables you to store your
favorite tracks from any disc in the player memory.
A program can contain 30 tracks.
Note:
The programs are also cleared when the power is off
or the disc is removed.
1. Insert an Audio CD recorded media.
AUDIO CD menu appears.
E
2. Press PROGRAM and the
mark will appear.
Note:
Press PROGRAM again to exit the program edit
E
mode, then the
mark will disappear.
3. Select a track on the “List”, then press ENTER
(OK) to place the selected track on the “Program”
list. Repeat to place additional tracks on the list.
4. Select the track you want to start playing on the
“Program” list.
5. Press N (PLAY) or ENTER (OK) to start.
Playback begins in the order in which you pro-
grammed the tracks. Playback stops after all of
the tracks on the “Program” list have played once.
6. To resume normal playback from programmed
playback, select a track on the list and then press
N (PLAY).
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Moving to another File
Viewing a JPEG file
Press . or > or cursor (b or B) once while
viewing a picture to advance to the next or previous
file.
This unit can play JPEG files.
1. Insert a disc of JPEG files. The PHOTO menu
appears on the TV screen.
Zoom
During watching pictures, press ZOOM to enlarge the
video image (3 steps).
You can move through the zoomed picture using b B
v V buttons.
Rotating the picture
Press v / V during showing a picture to rotate the
picture clockwise or counter clockwise.
2. Press v / V to select a folder, and press ENTER
(OK). A list of files in the folder appears.
3. If you want to view a particular file, press
v / V to highlight a file and press ENTER (OK) or
N (PLAY).
JPEG disc compatibility with this player is limit-
ed as follows:
4. To return to the PHOTO menu while watching pic-
tures, press x (STOP).
• Depending upon the size and the number of
JPEG files, it could take a long time for the DVD
player to read the disc’s contents. If you do not
see an on-screen display after several minutes,
some of the files may be too large — reduce the
resolution of the JPEG files to less than 5 million
pixels and burn another disc.
Note :
Some kind of special JPEG file can be taken more
time to play than normal JPEG.
(ex. Progressive JPEG)
Tips:
• The total number of files in a folder should be less
than 1000 files.
• If you are in a file list and want to return to the pre-
vious Folder list, use v / V buttons to highlight
and press ENTER (OK).
• Some discs may be incompatible due to a differ-
ent recording format or the condition of disc.
• Press DISC MENU to move to the next page.
• Ensure that all the selected files have the “.jpg”
extensions when copying into the CD layout.
• There are three Slide Speed options
(Fast), >> (Normal) and > (Slow).
: >>>
• If the files have “.jpe” or “.jpeg” extensions, please
rename them as “.jpg” file.
Use v V b B to highlight
select the option you want to use then press
ENTER (OK).
. Then, use b / B to
• File names without “.jpg” extension will not be
able to be read by this DVD player. Even though
the files are shown as JPEG image files in
Windows Explorer.
• While watching a picture, press O (RETURN) to
hide the help menu.
Slide Show
Use v V b B to highlight the
press ENTER (OK).
(Slide Show) then
Still Picture
1. Press X (PAUSE) during slide show.
The player will now go into PAUSE mode.
2. To return to the slide show, press N (PLAY) or
press X (PAUSE) again.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing a DVD VR format Disc
Maintenance and Service
This unit will play DVD-R/RW discs that are recorded
using the DVD-Video format that have been finalized
using a DVD-recorder.
Refer to the information in this chapter before
contacting a service technician.
Handling the Unit
This unit will play DVD-RW discs that are recorded
using the Video Recording (VR) format.
When shipping the unit
Please save the original shipping carton and packing
materials. If you need to ship the unit, for maximum
protection, re-pack the unit as it was originally packed
at the factory.
1. Insert a disc and close the tray, and playback start
automatically.
2. Press TITLE to move to the list menu.
Keeping the exterior surfaces clean
•
Do not use volatile liquids such as insecticide
spray near the unit.
•
Do not leave rubber or plastic products in contact
with the unit for a long period of time. since they
leave marks on the surface.
3. Press v / V to select a track then press N
(PLAY) or ENTER (OK) and playback starts.
Cleaning the unit
To clean the player, use a soft, dry cloth. If the sur-
faces are extremely dirty, use a soft cloth lightly mois-
tened with a mild detergent solution.
4. Press x (STOP) to stop the playback.
Notes:
• Unfinalized DVD-R/RW discs cannot be played in
this player.
Do not use strong solvents such as alcohol, benzine,
or thinner, as these might damage the surface of the
unit.
• Some DVD-VR disc are made with CPRM data by
DVD RECORDER. Player does not support these
kinds of discs and display the “CHECK DISC”.
Maintaining the Unit
The unit is a high-tech, precision device. If the optical
pick-up lens and disc drive parts are dirty or worn,
the picture quality could be diminished.
What is ‘CPRM’?
CPRM is a copy protection system (with scramble
system) only allowing the recording of ‘copy once’
broadcast programs. CPRM stands for Content
Protection for Recordable Media.
Depending on the operating environment, regular
inspection and maintenance are recommended after
every 1,000 hours of use.
For details, please contact your nearest authorized
service center.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference
Language Codes
Use this list to input your desired language for the following initial settings:
Disc Audio, Disc Subtitle, Disc Menu.
Language
Abkhazian
Afar
Afrikaans
Albanian
Ameharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
Code
6566
6565
6570
8381
6577
6582
7289
6583
6588
6590
6665
6985
6678
6890
6672
6682
6671
7789
6669
7577
6765
9072
6779
7282
6783
6865
7876
6978
6979
6984
7079
Language
Fiji
Finnish
French
Frisian
Galician
Georgian
German
Greek
Greenlandic
Guarani
Gujarati
Hausa
Code
7074
7073
7082
7089
7176
7565
6869
6976
7576
7178
7185
7265
7387
7273
7285
7383
7378
7365
7165
7384
7465
7487
7578
7583
7575
7589
7579
7585
7679
7665
7686
Language
Lingala
Lithuanian
Macedonian
Malagasy
Malay
Malayalam
Maltese
Maori
Code
7678
7684
7775
7771
7783
7776
7784
7773
7782
7779
7778
7865
7869
7879
7982
8065
8083
7065
8076
8084
8185
Language
Singhalese
Slovak
Slovenian
Somali
Spanish
Sudanese
Swahili
Swedish
Tagalog
Tajik
Tamil
Tatar
Telugu
Thai
Tibetan
Tigrinya
Tonga
Turkish
Turkmen
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapük
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
Code
8373
8375
8376
8379
6983
8385
8387
8386
8476
8471
8465
8484
8469
8472
6679
8473
8479
8482
8475
8487
8575
8582
8590
8673
8679
6789
8779
8872
7473
8979
9085
Marathi
Moldavian
Mongolian
Nauru
Bengali; Bangla
Bhutani
Bihari
Hebrew
Hindi
Nepali
Norwegian
Oriya
Panjabi
Pashto, Pushto
Persian
Polish
Portuguese
Quechua
Rhaeto-Romance 8277
Rumanian
Russian
Samoan
Sanskrit
Scots Gaelic
Serbian
Serbo-Croatian
Shona
Sindhi
Hungarian
Icelandic
Indonesian
Interlingua
Irish
Breton
Bulgarian
Burmese
Byelorussian
Cambodian
Catalan
Chinese
Corsican
Croatian
Czech
Danish
Dutch
English
Esperanto
Estonian
Faroese
Italian
Japanese
Javanese
Kannada
Kashmiri
Kazakh
Kirghiz
8279
8285
8377
8365
7168
8382
8372
8378
8368
Korean
Kurdish
Laothian
Latin
Latvian, Lettish
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Check the following guide for the possible cause of a problem before contacting service.
Cause
Correction
Symptom
No power.
ꢀ The AC power plug is disconnected
from the AC outlet.
ꢀ Connect the AC power plug to the
AC outlet securely.
ꢀ Insert a disc or tape. (Check that the
disc or tape indicator in the display
window is lit.)
Abnormal or no picture
ꢀ The TV is not set to receive unit signal
output.
ꢀ Select the appropriate video input
mode on the TV so the picture from
the unit player appears on the TV
screen.
ꢀ The video cable is not connected
securely.
ꢀ Check TV capability.
ꢀ Unit output setting.
ꢀ Check mode of connections
(eg. Components etc.).
ꢀ Wrong cable connection.
ꢀ The cable is correctly connected.
Distorted or no sound.
ꢀ The equipment connected with the
audio cable is not set to receive unit sig-
nal output.
ꢀ Select the correct input mode of the
audio receiver so you can listen to the
sound from the unit.
ꢀ The audio cables are not connected
securely.
ꢀ Connect the audio cable into the jacks
securely.
ꢀ The power of the equipment connected ꢀ Turn on the equipment connected with
with the audio cable is turned off. the audio cable.
ꢀ The AUDIO options are set to the wrong ꢀ Set the AUDIO options to the correct
position.
position.
The playback picture is
poor.
ꢀ The disc is dirty.
ꢀ Clean the disc.
ꢀ The TV channels are not tuned in
properly.
ꢀ The input source of TV is corrected.
ꢀ Tape heads are dirty.
ꢀ Clean video heads.
ꢀ Tape is a rental or was recorded on
another VCR.
ꢀ Use v/V (-/+) for manual tracking
adjustment while tape is playing.
ꢀ Insert a disc or tape. (Check that the
disc or tape indicator in the display
window is lit.)
The unit does not start
playback.
ꢀ No disc is inserted.
ꢀ No tape is inserted.
ꢀ Insert a playable disc. (Check the disc
type and Regional code.)
ꢀ An unplayable disc is inserted.
ꢀ Place the disc with the playback side
down.
ꢀ The disc is placed upside down.
ꢀ The disc is not placed within the guide.
ꢀ Place the disc on the disc tray cor-
rectly inside the guide.
ꢀ The disc is dirty.
ꢀ Clean the disc.
ꢀ The Rating level is set.
ꢀ Cancel the Rating function or change
the Rating level.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Cause
Correction
Symptom
ꢀ The cassette tape is already loaded.
ꢀ Eject the cassette tape.
Video tape cannot be
inserted.
No Hi-Fi sound
ꢀ Audio mode is not set properly.
ꢀ Select STEREO by repeatedly pressing
A.MONITOR on the Remote Control.
Remote Control
The
does not work properly.
ꢀ There is an obstacle in the path of the
Remote Control and this unit.
ꢀ Remove the obstacle.
ꢀ The batteries in the Remote Control
are exhausted.
ꢀ Replace the batteries with new ones.
ꢀ The Remote Control is not pointed at
the remote sensor of the unit.
ꢀ Point the Remote Control at the remote
sensor of the unit.
ꢀ The remote control is too far from the
unit.
ꢀ Operate the Remote Control within 23ft
(7m).
ꢀ This Remote Control use the same
buttons for VCR and DVD functions
(ex.PLAY).
ꢀ When using a VCR, first press the VCR
button. When using a DVD, first press
the DVD button.
ꢀ Identify the remote control code with
the code of unit. (See page 17).
ꢀ The current remote control code does
not match the unit.
ꢀ Turn camcorder on and operate
properly.
Camcorder image is
not shown.
ꢀ Camcorder is off.
Camcorder image via
AV input to unit is not
shown on TV screen.
ꢀ Unit SOURCE SELECT is not set to
LINE1 or LINE2.
ꢀ Press AUX to select LINE input
channel (LINE1 or LINE2).
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
General
Power requirements
120V, 60 Hz
16 W
16.9" X 3.1" X 10.2" (430 X 79 X 260 mm) (w x h x d)
8.8 lbs (4.0 kg)
5˚C to 40˚C (41˚F to 104˚F)
5 % to 90 %
Power consumption
Dimensions (approx.)
Net Weight (approx.)
Operating temperature
Operating humidity
Signal system
NTSC
Inputs
VHS VIDEO IN(LINE1, 2)
VHS AUDIO IN(LINE1, 2)
1 V (p-p) 75 ohms, sync negative, RCA jack x 2
-6.0 dBm more than 47 ohms, RCA jack (L, R) x 2
Outputs
VIDEO OUT
1 V (p-p) 75 ohms, sync negative
COMPONENT VIDEO OUT
(PROGRESSIVE SCAN)
Audio output (digital audio)
Audio output (analog audio)
(Y) 1.0 V (p-p), 75 ohms, negative sync, RCA jack x 1
(Pb)/(Pr) 0.7 V (p-p), 75 ohms, RCA jack x 2
0.5 V (p-p), 75 ohms, RCA jack x 1
2.0 Vrms (1 KHz, 0 dB), 600 ohms, RCA jack (L, R) x 2
VCR Specifications
Head system
Timer
Tape speed
Four head helical scan azimuth system
12-hour display type with AM, PM
SP: 33.35 mm/sec, LP: 16.67 mm/sec, SLP: 11.12 mm/sec
12.7 mm
SP: 2 HOURS (T-120), SLP: 6 HOURS (T-120)/8 HOURS (T-160)
About 3 minutes (T-120)
20 Hz to 20 kHz
More than 43 dB
More than 88 dB
More than 60 dB
Tape width
Maximum recording time
Rewind time
Frequency range
Signal-to-noise ratio
Dynamic range
Channel separation
DVD Specifications
Laser system
Frequency response
Semiconductor laser, wavelength 650 nm
DVD (PCM 96 kHz): 8 Hz to 44 kHz,
DVD (PCM 48 kHz): 8 Hz to 22 kHz
CD: 8 Hz to 20 kHz
Signal-to-noise ratio
Harmonic distortion
Dynamic range
More than 90 dB (ANALOG OUT jacks only)
Less than 0.02%
More than 95 dB (DVD/CD)
Accessories:
Video cable x 1, Audio cable (L/R) x 1, Remote control x 1, Batteries (R03/AAA) x 2
Note : Design and specifications are subject to change without prior notice.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty (Only in U.S.A.)
33
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
34
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Printed in Indonesia
0108MNH-OT-OT
US
P/N: MFL46896801
Download from Www.Somanuals.com. All Manuals Search And Download.
|