Preliminary
HD NETWORK CAMERA
SD Card Operation Manual
(Settings Supplement)
VN-H37U/H57U Series
Contents
„Precautions for using SD cards.................................................................................... 2
„SD Cards...................................................................................................................... 3
„Built-in Viewer Screen Configuration............................................................................ 5
„SD Card Playback Screen............................................................................................ 6
zVideo control menu .................................................................................................. 9
„Basic Setting2 Page ................................................................................................... 10
„SD Card Record Page................................................................................................ 12
„Recording Time for SD Card Recording Function ...................................................... 18
zRecording time table .............................................................................................. 18
„Additional Cautions..................................................................................................... 19
zCautions for setting the detection function ............................................................. 19
zCautions for changing the encoding setting ........................................................... 19
zChecking the software version ............................................................................... 19
„Troubleshooting.......................................................................................................... 20
This camera supports SD card recording and playback functions with V4.00 firmware and above.
Read this manual carefully before using SD card recording and playback functions.
LST1392-001A
Download from Www.Somanuals.com. All Manuals Search And Download.
SD Cards
„
This unit can record the images you shoot in an SD card (sold separately) inserted in the card slot.
Memo:
z If the SD card's switch is set to “Lock”, recording and playback cannot be performed. Make sure there is no
critical data on the SD card before disengaging the lock.
z If you insert the SD card in the incorrect direction, the camera or the card may be damaged. Always check
that the card has been inserted in the correct direction as shown in the illustration of the SD card slot.
When using VN-H237U/H257U/ H237VPU/H257VPU
SD card slot
SD card LED
SD card slot
SD card LED
When using VN-H37U/H57U/H137U
SD card cover
③
②
SD mark
SD card LED
①
One (M1.4) setscrew
Follow the steps below to insert an SD card.
1. Loosen the setscrew (1) by rotating it about 3 times, and then open the SD cover.
Note：
Rotating the setscrew 10 times or more may cause it to fall out.
z
①Lift the setscrew side of the SD cover slightly from the camera body.
※You can pull the setscrew up by its edge to keep it suspended.
②Slide the SD cover to the direction of the setscrew side.
③Lift and open the side with a slit of the SD cover from the camera body.
2. Insert the SD card into the slot until it clicks.
3. Close the SD cover, and retighten the setscrew.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
When using VN-H157WP
3
SD card cover
1・3
SD card
(label side)
4
1
Sunshade rotation
setscrew
Follow the steps below to insert an SD card.
1. Loosen the screw at the bottom of the camera, and rotate the sunshade enough so that the SD card
can be inserted.
2. Perform insertion (or removal) of the SD card.
(If an SD card cover is attached, pull it off to remove it.)
3. Return the sunshade to its original position.
4. Fasten the screw after the adjustment.
Memo:
z If the sunshade cannot be rotated because it is difficult to access, turn the camera before performing this
procedure. After finishing, return the camera to its original angle, verify the camera image, and readjust
settings if necessary.
Use the following SD cards.
SDHC cards (4 to 32 GB) of Class 10 or above
Use SD cards with a guaranteed operation temperature of 85 ℃ or higher.
The following SD cards are confirmed to function correctly with this camera:
•Panasonic
•Toshiba
: RP-SDW04GJ1K
: SD-FX004G
•SanDisk
: SDSDX-004G-J95
z Operation of all SD cards that meet the above conditions is not guaranteed.
Memo:
z Do not leave the SD card slot cover open for a long period of time. Dust may enter inside and cause
malfunctions. (VN-H37U/H57U/H137U only)
z Make sure to set [SD Card] on the Record page to [Disable] before removing an SD card or turning off this
z When using an unsupported SD card, it can be set to record, but recording errors may occur.
z You can easily remove the SD card by lightly pushing it inward to release the lock. The SD card may pop
out when you eject it. Exercise care not to lose it.
z Some SD cards on the market may be difficult to remove from the camera body. After the card has been
inserted and removed several times, it will be easier to remove.
z Turn off camera before inserting or changing the SD card.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Built-in Viewer Screen Configuration
„
Start the Built-in Viewer by entering the IP address of the camera in the address bar of Internet Explorer.
①
②
No.
Item
SD Card
Description
Press the [SD Card] button to display the SD Card Playback Screen.
①
Memo:
z If you log in with only user privileges, the [SD Card] button becomes
unselectable, and SD card playback cannot be performed.
REC
The REC icon is displayed while recording to an SD card.
②
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SD Card Playback Screen
„
This is displayed when you click [SD Card] on the Built-in Viewer screen.
You can play video files stored in the SD card.
①
⑥
⑦
⑧
⑨
⑩
②
③
⑪
④
⑫
⑤
Memo:
z Video recorded to an SD card cannot be output from the camera's [MONITOR] terminal.
No.
Item
Description
Displays / hides the operation menu.
MENU ON /
MENU OFF
①
Click [MENU ON] to display the menu on the left side of the page.
Video control
menu
Controls the video playback state.
②
③
Specified Time
Playback menu
Specify the date and time before starting playback.
[Playback] button
Press the [Playback] button to play videos recorded at the specified date and
time.
Memo:
z If there is no video recorded for the specified date and time, video near that
date and time will be played.
z When playing video while recording, video recorded within 5 minutes of the
current time cannot be viewed.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
No.
Item
Description
Event List
Displays a list of search results for recorded videos filtered by time and event
trigger. Select the item from the displayed list that you want to play and begin
playback.
④
Playback menu
From/To
Displayed videos will be limited to those recorded between the 2 times that you
specify.
Event Type
Displayed videos will be limited to those of the event trigger* type that you
specify.
* Event Trigger： Pin Input1 Make, Pin Input2 Make, Motion Detection, Position, Day/Night, Audio
Detection1, Audio Detection2 (VN-H57U/H257U/H257VPU/H157WPU only), Tampering Detection,
Time
Memo:
z Depending on the camera model, you may be unable to select the event
trigger.
z A starting event for continuous recording cannot be specified.
[Search] button
A list of search results based on the search parameter that you add a check to is
displayed. If no search parameter is checked, all events are displayed.
Event List
Displays a list of recording start dates/times with the event type in chronological
order from the newest event.
[Prev] / [Next] buttons
A maximum of 100 results can be displayed on 1 page. Press [Prev] to move to
pages with newer recording start dates/times, and press [Next] to move to pages
with older recording start dates/times.
[Playback] button
Select an event from the list and press the [Playback] button to start playback.
Note：
z When an event is finished playing, the next event is automatically played back.
(The list marker in the list does not move to the next event displayed in the
list.)
z If you record over the recording start date/time of a video, the event
disappears from the list. You can still play portions of the video that have not
been overwritten by using the [Specified Time Playback] menu.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
No.
Item
Description
Video from the specified [From] date/time to the [To] date/time is saved to your
computer.
Export menu
⑤
The save location can be specified in [Viewer Setup] - [Other] - [Video Export
Folder] via the Built-in Viewer screen.
Note:
z Depending on the camera's internal recordings, a saved video may be split up
as multiple files.
z For using saved video files, refer to the following URL.
[IN] button
Specifies the start time of the video being played.
[OUT] button
Specifies the end time of the video being played.
[Export] button
After pressing this button, the confirmation screen is displayed, and then the
video saving process begins.
While saving videos, this button changes to [Cancel].
Memo:
z While saving videos, the Built-in Viewer screen cannot be switched.
z Saving may take time depending on the date/time range that you specify.
Progress is displayed at the top of the screen.
[Cancel] button
After clicking the [Export] button, this cancels the save operation for the images
being output.
The file created contains the data written until the point when you press the
button.
Memo:
z When the export process is stopped, this button changes to [Export].
z When the time required for exporting video to a computer is less than 5
seconds, this button has no effect.
[Live] button
Switches to the Built-in Viewer screen.
⑥
⑦
⑧
⑨
⑩
Playback indications Displays playback conditions.
Time Stamp
Display Time
Display Size
Shows the recording date and time of the video currently playing.
You can enable/disable the display of the recording time during playback.
Sets the display size of the image area.
[Set values: Fixed, Variable]
Video display
area
Displays the recorded video.
⑪
⑫
Shows the recording date and time of the video currently playing. [⑨Display
Time Stamp
Time] is used for setting whether or not to display this.
* The [Set values] in bold letters are factory defaults.
Memo:
z SD card playback from 1 camera cannot be performed to multiple viewers.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Video control menu
z
①
②
③
④
⑤
⑧
⑥
⑦
⑨
⑫
⑮
⑩
⑪
⑬
⑭
No.
Item
Description
No.
Item
Description
Returns to the previous frame,
and then pauses playback.
Advances to the most recent
frame, and then pauses playback.
①
⑨
Starts reverse playback.
Pauses playback.
Reverses the playback position.
②
③
⑩
⑪
Selects the fast-forward and
reverse speeds.
[Set values :
, x1, x3, x10,
x1/2
Starts playback.
④
⑤
⑥
⑦
x30, x60]
Advances to the next frame, and
then pauses playback.
Fast-forwards the playback
position.
⑫
⑬
⑭
Returns to the oldest frame, and
then pauses playback.
Returns by the specified length of
time, and then pauses playback.
Jumps to the previous alarm
event video.
Selects the length of time to move.
[Set values :
, 15s, 30s, 1m,
10s
10m, 30m, 1h, 6h,
12h, 24h]
Jumps to the next alarm event
video.
Advances by the specified length
of time, and then pauses playback.
⑧
⑮
* The [Set values] in bold letters are factory defaults.
Memo:
z For playback from an SD card, use [Specified Time Playback] menu or [Event List Playback] menu
z When playback of an event finishes, playback of the next event starts automatically.
z Buttons other than button ④ and button ⑤ are only used with I-frame playback.
z Button ⑦ and button ⑧ are only used to jump to alarm event videos. You cannot jump to a continuous
recording event.
z A maximum of 1 second of calculation error from the specified time set via button ⑭ may occur when
jumping using button ⑬ and button ⑮.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Setting2 Page
„
This page sets fundamental camera and encoding parameters.
This page can be used during access using "admin" or "operator".
Click [Basic Setting2].
①
②
③
④
Memo:
z If you enter the following URL directly into the address bar of Internet Explorer, you can open the [Basic
Setting2] page without going through the Built-in Viewer.
z Press the [OK] button to enable the new settings.
z If the [OK] button is pressed upon entering an invalid value, a warning message will appear and the entry
will be denied. Press the [Cancel] button to restore the invalid entry to the value before the change was
made.
z "H.264 High" indicates the H.264 High Profile standard.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
No.
①
Item
Description
Camera ID
Refer to the "Instructions (Setting)" of the supplied CD-ROM.
Scenefile
Lens Type
Encode
②
③
Select the frame size for each screen of JPEG and H.264 from the following six
patterns.
④
■Selectable distribution size
Commu-
nication
speed
Frame
Size
Frame
Rate
Bit
rate
I Frame
Interval
Set value
H.264 High
1
2
3
1920x1080
1920x1080
1920x1080
30 fps
5 fps
5 fps
8 Mbps
2 Mbps
200 KB
CBR
CBR
AFS
30 frames
5 frames
－
1920×1080 30 fps
H.264 High
1920x1080 5 fps
+ monitor output
JPEG 1920x1080
+ monitor output
4
5
JPEG 1280x960
JPEG 640x480
1280x960
640x480
5 fps
5 fps
120 KB
30 KB
AFS
AFS
－
－
Set in "SD Card Record"
Page
6
7
Settings can be configured in the [SD Card Record] page.
Multi-encoding and details can be set on [Encoding] page.
Set in "Encoding" Page
* The [Set values] in bold letters are factory defaults.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
SD Card Record Page
This page sets SD card recording settings.
„
This page can be used during access using "admin" or "operator".
Click [Advanced Settings] and [SD Card Record].
①
②
③
④
⑤
⑥
Memo:
z If the status is "Read only" or "No insert", nothing can be selected other than the [OK] button or the [Cancel] button.
z When recording to FTP and you attempt to perform SD card recording settings, the display changes to a
dialog for interrupting FTP recording and starting SD card recording is displayed. When you press the [OK]
button, FTP recording stops and SD card recording starts.() "Instructions (Setting)" ─ "Internet Explorer
Setting" ─ "Advanced Settings" ─ "Storage Page")
z When recording to an SD card is enabled and you attempt to perform FTP recording settings, the display
changes to a dialog for interrupting SD card recording and starting FTP recording is displayed. When you
press the [OK] button, SD card recording stops and FTP recording starts.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
No.
Item
SD Card
Description
①
[Set values ：Use, Disable]
Check "Disable" and press the [OK] button to automatically set recording to OFF
and stop recording.
Check "Use" and press the [OK] button to enable all the SD card
recording-related check boxes.
Memo：
z Video recorded to an SD card can be played via the SD card playback screen
that is displayed by clicking the [SD Card] button on the Built-in Viewer screen.
z Encoding settings cannot be changed while recording to an SD card.
[Status ： Disable, Use, Read only, No insert]
Disable
Use
： Displayed when "Disable" is selected.
： Displayed when "Use" is selected.
Read only ： Displayed when the SD card's switch is set to "Lock". Remove the
SD card and disable the "Lock" in order to record and playback to
the SD card.
No insert ： Displayed when the SD card is not inserted into the camera. Insert
an SD card.
* The [Set values] in bold letters are factory defaults.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
No.
Item
Format
Description
This button is for executing a format of the SD card.
②
[Status ： Unformatted, Formatting, Formatted, ---]
"---" is displayed when the SD card status display is not "Use".
"Unformatted" is displayed when the SD card is not formatted, or when an
unsupported class of SD card that cannot be formatted is inserted.
The [Execute] button cannot be pressed (and becomes grayed out) when the SD
card status display is not "Use".
To enable the [Execute] button, select "Use" for the "SD Card" setting, click the
[OK] button, and confirm that "Use" is displayed for the SD card status.
When the [Execute] button is pressed, a confirmation window will appears. Press
the [OK] button to begin formatting the SD card. The status becomes
"Formatting" during formatting.
After formatting the card, the format complete dialog is displayed and the camera
restarts. The status becomes "Formatted".
Press the [OK] button to close the screen.
Memo：
z Make sure to format the SD card with the camera before using it.
Only SD cards formatted with the camera can be used.
z It takes approximately 1 minute to format a 32 GB SD card.
z Do not remove the SD card during formatting.
z Do not turn off the power while the card is being formatted.
z You cannot record to the SD card while it is being formatted.
Note：
z When changing the time of the camera via the following operations, first make
sure to stop recording to the SD card. If times on the SD card for recorded
video overlap due to changes in the camera's time, the camera may become
unable to perform playback correctly.
- When changing the time via "Setting the PC's time to the camera" ()
"Instructions (Setting)" ─ "Internet Explorer Setting" ─ "Advanced
Settings" ─ "Basic Setting1 Page")
- When changing the time via "Time" and "Setting the PC's time to the
camera" ()"Instructions (Setting)" ─ "Internet Explorer Setting" ─
"Advanced Settings" ─ "Time Page")
- When changing the "Time Zone" setting ()"Instructions (Setting)" ─
"Internet Explorer Setting" ─ "Advanced Settings" ─ "Time Page")
z Playback search may not operate correctly for video with time that overlaps
due to the time changes to and from Daylight Saving Time. By shifting this
video via fast forward and fast reverse, playback is possible.
z The Sense Up function ()"Instructions (Setting)" ─ "Internet Explorer Setting"
─ "Advanced Settings" ─ "Camera Page") causes the frame rate of video
recorded to the SD card to drop; therefore, the playback speed of recorded
video may vary.
* The [Set values] in bold letters are factory defaults.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
No.
Item
Description
Record Status
③
[Set values : ON, OFF]
[Status : No Recording, Recording]
This is only enabled when the SD card status is "Use" and the format status is
"Format complete".
When recording, the status changes to [Recording]. When recording is stopped,
the status changes to [Stopped]. When only alarm recording is selected, the
status is [Stopped] at times other than when the alarm is engaged.
Check "ON" and check one of the available settings in "Recording image quality
settings" to begin continuous-loop recording to the SD card with the selected
recording quality.
Starts continuous-loop recording to the SD card with the selected recording
quality.
If you push [OK] when the encoding setting has not been set, the "Select an
encoding setting." dialog is displayed and recording does not start.
Select "OFF" and click the [OK] button to stop recording.
Recording
To change the recording image quality, select "OFF" for ③ Record Status, push
the [OK] button to stop recording, and then configure settings.
④
image quality
If you push [OK] when the recording image quality has not been set, the "Set the
recording mode." dialog is displayed and recording does not start.
You can select either "Constant", "Alarm", or both settings.
Memo：
z When the record status is "ON", the setting for Recording image quality cannot
be changed.
Constant
Alarm
Constantly records to the SD card.
SD card recording is performed when conditions set for the alarm setting items
are met. The alarm event recording interval for when an alarm is triggered is from
60 seconds before the trigger (pre-trigger) to 60 seconds after the trigger
(post-trigger), for a total of 120 seconds.
Memo：
z Even if another trigger is detected within 60 seconds of the first trigger, it will
not appear in the event list.
z If another trigger is detected during alarm recording, recording is extended 60
seconds from the original end point.
z If less than 60 seconds have passed since video recording was initially started,
the pre-trigger time will be less than 60 seconds.
* The [Set values] in bold letters are factory defaults
Alarm recording-related setting items are displayed when "Alarm" is selected.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
No.
Item
Description
Alarm Settings
⑤
Trigger1
Select the 1st trigger to perform an action.
When using VN-H57 series
[Set values： Pin Input1 Make, Pin Input1 Break, Pin Input2 Make,
Pin Input2 Break, Position, Audio Detection1,
Audio Detection2 (VN-H57U/H257U/H257VPU/H157WPU only),
Motion Detection, Tampering Detection, Day/Night, Time]
When using VN-H37 series
[Set values： Position, Motion Detection, Tampering Detection, Time]
Memo:
The trigger for [Trigger1] must first be set to "ON" in the respective [Advanced
Settings] configuration page.
z
z
z
If you set the [Trigger2] to "Disable", an action will be performed when only
[Trigger1] is triggered. (VN-H57U/H257U/H257VPU/H157WPU only)
When “Audio Detection1”, ”Audio Detection2”, "Motion Detection",
"Position" ”Tampering Detection”, “Day/Night”, or ”Time” is selected for the
[Trigger1] trigger, [Interval] and [Trigger2] cannot be selected. (VN-H57U/
H257U/H257VPU/H157WPU only)
Interval
This is available when both [Trigger1] and [Trigger2] are set.
(VN-H57U/H2 Specify the maximum interval between each trigger for [Trigger1] and [Trigger2].
57U/H257VP
U/H157WPU
only)
An action will be performed if [Trigger2] occurs within the maximum time interval
after [Trigger1] occurs.
[Set values：1 – 3600 ] sec
Memo:
z If you set an invalid value, the "Invalid value" dialog is displayed.
z If you leave a value blank, the "Blank value" dialog is displayed.
Trigger2
Select the 2nd trigger to perform an action.
[Set values：Disable, Pin Input1 Make, Pin Input1 Break, Pin Input2 Make,
Pin Input2 Break]
(VN-H57U/H2
57U/H257VP
U/H157WPU
only)
Position
Number
Enabled when "Position" is set for the trigger for [Trigger1].
Perform registration of position numbers via the Built-in Viewer's "PTZ setting".
()“Instructions(Setting)” ─ "Operations" ─ "Built-in Viewer Operations" ─ "PTZ
Settings")
This position condition will also work if you manually move the PTZ, or if the PTZ
is automatically moved via auto patrolling.
[Set values: 0 – 19]
* The [Set values] in bold letters are factory defaults
Memo:
If you set the same items for [Trigger1] and [Trigger2], the "Trigger1 and Trigger2 are the same." dialog is
displayed and alarm recording is not started.
z
16
Download from Www.Somanuals.com. All Manuals Search And Download.
No.
Item
Description
Encode Setting
When the Read Status is "ON", the setting for Encode Setting cannot be
changed.
⑨
To change the settings, select "OFF" for the recording item, push the [OK] button
to stop recording, and then configure settings.
If you set the recording item to "ON" and push the [OK] button when the encoding
setting has not been set, the "Select an encoding setting." dialog is displayed and
recording does not start.
[Encode Setting]
Encoder No.1 1920x1080, 5fps, 1024kbps, CBR, 5 I Frame Interval (SD Card REC)*1
Setting
Encoder No.2 1280x720, 5fps, 1024kbps, CBR, 5 I Frame Interval
Pattern 1
Encoder No.3 640x360, 5fps, 512kbps, CBR, 5 I Frame Interval
Encoder No.1 1920x1080, 5fps, 1024kbps, CBR, 5 I Frame Interval (SD Card REC)*1
Setting
Encoder No.2 1280x720, 5fps, 768kbps, CBR, 5 I Frame Interval
Pattern 2
Encoder No.3 640x360, 5fps, 256kbps, CBR, 5 I Frame Interval
Encoder No.1 1920x1080, 5fps, 2048kbps, CBR, 5 I Frame Interval
Setting
Encoder No.2 1280x720, 5fps, 768kbps, CBR, I5 I Frame Interval (SD Card REC)*1
Pattern 3
Encoder No.3 640x360, 5fps, 512kbps, CBR, 5 I Frame Interval
Encoder No.1 1920x1080, 5fps, 1024kbps, CBR, 5 I Frame Interval
Setting
Encoder No.2 1280x720, 5fps, 768kbps, CBR, 5 I Frame Interval(SD Card REC)*1
Pattern 4
Encoder No.3 640x360, 5fps, 256kbps, CBR, 5 I Frame Interval
Encoder No.1 1920x1080, 5fps, 1024kbps, CBR, 5 I Frame Interval
Setting
Encoder No.2 1280x720, 5fps, 384kbps, CBR, 5 I Frame Interval (SD Card REC)*1
Pattern 5
Encoder No.3 640x360, 5fps, 128kbps, CBR, 5 I Frame Interval
Encoder No.1 1920x1080, 5fps, 1024kbps, CBR, 5 I Frame Interval
Setting
Encoder No.2 1280x720, 5fps, 768kbps, CBR, 5 I Frame Interval
Pattern 6
Encoder No.3 640x360, 5fps, 256kbps, CBR, 5 I Frame Interval (SD Card REC)*1
Encoder No.1 1920x1080, 5fps, 2048kbps, CBR, 5 I Frame Interval
Setting
Encoder No.2 1280x720, 5fps, 1536kbps, CBR, 5 I Frame Interval
Pattern 7
Encoder No.3 640x360, 5fps, 128kbps, CBR, 5 I Frame Interval (SD Card REC)*1
Encoder No.1 1920x1080, 5fps, 1024kbps, CBR, 5 I Frame Interval
Setting
Encoder No.2 1280x720, 5fps, 384kbps, CBR, 5 I Frame Interval
Pattern 8
Encoder No.3 640x360, 5fps, 128kbps, CBR, 5 I Frame Interval (SD Card REC)*1
*1:Video from the encoder number with the designation "(SD Card REC)" is recorded to the SD card.
* The [Set values] in bold letters are factory defaults
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording Time for SD Card Recording Function
„
Recording time table
z
Available recording time for each SD card
size [in hours]
Setting
Pattern
Encoding details for SD card recording
4 GB
8 GB
16 GB
32 GB
Setting
Pattern 1
1920x1080, 5fps, 1024kbps, CBR, 5 I Frame
Interval
5
12
25
52
Setting
Pattern 2
Setting
Pattern 3
1280x720, 5fps, 768kbps, CBR, 5 I Frame
Interval
7
15
34
70
Setting
Pattern 4
Setting
Pattern 5
1280x720, 5fps, 384kbps, CBR, 5 I Frame
Interval
12
19
27
42
58
92
120
189
Setting
Pattern 6
640x360, 5fps, 256kbps, CBR, 5 I Frame
Interval
Setting
Pattern 7
640x360, 5fps, 128kbps, CBR, 5 I Frame
Interval
34
78
169
384
Setting
Pattern 8
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Cautions
„
Cautions for setting the detection function
z
You cannot set motion detection, audio detection, and tampering detection at the same time.
An error message is displayed when one detection function setting is already enabled and you try to select
another. Check the content of the error message, set the already-enabled detection function to "OFF", and
then reconfigure the detection function. () "Instructions (Setting)" ─ "Operations" ─ "Motion Detection Page",
"Audio Detection Page", "Tampering Detection Pages")
Cautions for changing the encoding setting
z
When changing an already-configured encoding setting on the Basic Settings 2 page, Encoding page, or SD
recording page, PTZ and the auto patrol settings are cancelled.
In this case, set PTZ and the auto patrol settings again after setting the encoding setting. ()"Instructions
(Setting)" ─ "Operations" ─ "PTZ Page", "Auto Patrol Page")
Checking the software version
z
Check on the following screen that the software version is "1.4.30".
Check that this is
"1.4.30".
Click [Advanced Settings] and [Miscellaneous]
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
„
Check the following items if you cannot record to an SD card.
z Disengage the lock on the SD card.
z Follow the instructions in [SD Card Record Page] () Page 12) to enable SD card recording settings.
© 2012 JVC KENWOOD Corporation
LST1392-001A
Download from Www.Somanuals.com. All Manuals Search And Download.
|