JVC CRT Television HV 29JH24 HV 29JH54 HV 29JH74 HV 29VH14 HV 29JH54 User Manual

COLOUR TELEVISION  
Contents  
Introduction of the functions . . . . . . 2  
Setting up your TV . . . . . . . . . . . . . 3  
TV buttons and functions . . . . . . . . 6  
Remote control buttons  
HV-29JH24  
HV-29JH54  
HV-29JH74  
HV-29VH14  
HV-29VH54  
and functions . . . 8  
Using the TV's menu. . . . . . . . . . . . 19  
Basic operation . . . . . . . . . . . . . . 19  
PICTURE SETTING menu . . . . . 20  
PICTURE FEATURES menu . . . 21  
SOUND SETTING menu . . . . . . 25  
FEATURES menu . . . . . . . . . . . 26  
INSTALL menu . . . . . . . . . . . . . . 29  
Additional preparation . . . . . . . . . . 35  
Troubleshooting . . . . . . . . . . . . . . 37  
Specification . . . . . . . . . . . . . . . . . 40  
INSTRUCTIONS  
GGT0056-001A-H  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting up your TV  
CAUTION  
• Turn off all the equipment including the  
TV before connecting anything.  
1 Connecting the aerial and VCR  
• Aerial cable is not supplied. Use a  
good quality 75-ohm coaxial cable.  
• Read the manual that came with the  
VCR before connecting.  
Fig. A  
Back of the TV  
If not connecting a VCR (see Fig. A):  
AUDIO  
L/MONO VIDEO  
R
S
OVER  
Connect an aerial cable to the aerial socket  
on this TV.  
VIDEO-1  
VIDEO-2  
If connecting a VCR (see Fig. B):  
PR/CR PB /CB  
Y/VIDEO  
VIDEO-3/  
COMPONENT  
AUDIO  
1 Connect the aerial cable to the aerial  
input socket on the VCR, and connect  
the VCR and TV with another aerial  
cable.  
R
R
L/MONO  
OUTPUT  
L
VIDEO  
AUDIO  
2 Connect the VCR’s VIDEO OUT (video  
output) jack and the TV’s VIDEO jack  
with a video cable.  
To connect a VCR to the TV with an S-  
VIDEO cable:  
Connect the VCR’s S-VIDEO OUT (S-  
VIDEO output) connector and TV’s S  
connector with an S-VIDEO cable A,  
instead of connecting with a video cable.  
Fig. B  
AUDIO  
L/MONO VIDEO  
Back of the TV  
R
S
OVER  
VIDEO-1  
VIDEO-2  
3 Connect the VCR’s AUDIO OUT (audio  
L/R output) jacks and the TV’s AUDIO  
jacks (L/MONO and R) with an audio  
cable.  
PR/CR  
P /CB  
B
Y/VIDEO  
VIDEO-3/  
COMPONENT  
AUDIO  
R
R
L/MONO  
• If the VCR’s audio output is in mono,  
connect the VCR’s AUDIO OUT (audio  
output) jack and the TV’s AUDIO L/  
MONO jack with an audio cable.  
OUTPUT  
L
VIDEO  
AUDIO  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting up your TV  
2 Connecting the power cord  
Connect the mains plug to the AC outlet.  
3 Putting the batteries into the  
remote control  
Use two AA/R6 batteries.  
Insert the batteries from the -end, making  
sure the +and -polarities are correct.  
• Follow the warnings printed on the  
batteries.  
• If the remote control does not work  
properly, replace the batteries.  
• The batteries we supply are only for  
setting up and testing your TV. Please  
replace them as soon as necessary.  
HV-29JH24 / HV-29JH54 /  
HV-29JH74  
4 Making the initial settings  
When the TV is first turned on, it enters the  
initial setting mode, and the JVC logo is  
displayed.  
P
O
W
E
R
I
MU  
CN
T
/
I
E
O
V
/
X
1 Press the main power button on the  
TV.  
The TV is turned on, and the JVC logo  
appears.  
• If the POWER lamp on the TV lights  
red and does not change to green,  
your TV is in the standby mode. Press  
the POWER button on the remote  
control to turn the TV on.  
POWER  
POWER lamp  
Main power button  
• If the JVC logo does not appear, your  
TV has already been turned before. In  
this case, use the “LANGUAGE” and  
“AUTO PROGRAM” functions to make  
the initial settings. For details, see  
“INSTALL menu” on page 29.  
HV-29VH14 / HV29VH54  
2 Press the MENU/OK button.  
The LANGUAGE menu appears. You  
can choose a language for the on-screen  
language.  
POWER  
POWER lamp  
Main power button  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting up your TV  
3 Press the 6buttons to choose  
ENGLISH. Then press the MENU/ OK  
button.  
The AUTO PROGRAM function starts.  
The TV channels you receive are  
automatically stored in the PR  
(programme numbers) LIST.  
MUTING  
POWER  
SYSTEM  
CINEMA  
COLOUR SOUND SURROUND ZOOM  
PIP  
DISPLAY  
Except  
HV-29JH24  
HV-29VH14  
MENU  
OK  
TV/TEXT  
Except  
HV-29JH54  
HV-29VH14  
HV-29VH54  
TV/VIDEO  
1
4
2
5
8
0
3
6
9
PICTURE  
MODE  
• To stop the AUTO PROGRAM  
7
RETURN  
function, press the MENU/OK button.  
SUB-P  
Except  
+
HV-29JH24  
HV-29VH14  
4 After the TV channels have been  
stored in the programme numbers  
(PR) list, the EDIT menu appears.  
CHANNEL  
VOLUME  
FAVORITE CH  
RM-C1350  
TV  
HV-29JH74  
FAVORITE CH  
• You can proceed to edit the  
programme numbers list using the  
EDIT/MANUAL function. For details,  
see “EDIT/MANUAL” on page 30.  
• If a TV channel you want to view is not  
stored in the programme numbers list,  
you can register it using the MANUAL  
function. For details, see “EDIT/  
MANUAL” on page 30.  
RM-C1351  
TV  
HV-29JH24  
FAVORITE CH  
• The AUTO PROGRAM function does  
not store a TV channel to the  
programme number 0 (AV).  
RM-C1353  
TV  
HV-29JH54 / HV-29VH54  
FAVORITE CH  
• If you do not need to use the EDIT/  
MANUAL function, press the MENU/  
OK button to close the EDIT menu.  
Now, setting up is complete. Please  
enjoy your new JVC TV!  
HV-29VH14  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
TV buttons and functions  
Turn the main power on  
HV-29JH24 / HV-29JH54 /  
HV-29JH74  
Press the main power button 1.  
The POWER lamp 2 lights red and your TV  
is in the standby mode.  
To turn the main power off:  
Press the main power button again. The  
POWER lamp 2 goes off.  
P
O
W
E
R
I
(
I
-
)
U  
O
CN
D
O
L
E
Turn the TV on from standby  
mode  
Press the CHANNEL-/+ buttons 5.  
The POWER lamp 2 lights red to green  
and your TV will be turned on.  
POWER  
• You can also turn on the TV by  
pressing the TV/VIDEO button 3  
while it is in standby mode.  
1
2
7
Choose a TV channel  
P
O
W
E
R
I
N
D
E
O
4
OK  
O
I
EXT  
V
L
Press the CHANNEL-/+ buttons 5.  
(Behind the cover)  
IN (VIDEO-4)  
MENU  
CHANNEL  
VOLUME TV/VIDEO  
Choose a VIDEO terminal  
OVER  
V
L/MONO  
R
OK  
EXIT  
S
Press the TV/VIDEO button 3 or  
CHANNEL-/+ buttons 5.  
9
8
6 5 4 3  
Adjust the volume  
Press the VOLUME-/+ buttons 4.  
HV-29VH14 / HV29VH54  
The volume level indicator appears.  
MENU button 6  
Press to open the menu.  
For details, see “Operation with the buttons  
on the TV” on page 20.  
Remote control sensor 7  
(Behind the cover)  
POWER  
VIDEO-4 terminal 8  
See page 35.  
7
2
1
Headphone jack 9  
Connect the headphones with a stereo  
mini-jack (3.5mm in diameter).  
(Behind the cover)  
OVER  
V
L/MONO  
R
S
MENU  
OK  
CHANEL  
VOLUME TV/VIDEO  
EXIT  
IN (VIDEO-4)  
9
8
6 5 4 3  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
TV buttons and functions  
VIDEO-1 terminal 0  
• See pages 3 and 35.  
VIDEO-2 terminal -  
• See page 35.  
VIDEO-3/COMPONENT  
terminal =  
A
UDIO  
L/MONO  
VIDEO  
S
R
OVER  
VIDEO-1  
VIDEO-2  
CR  
CB  
Y/VIDEO  
AUDIO  
VIDEO-3  
COMPONENT  
R
R
L/MONO  
• See pages 28 and 35.  
OUTPUT  
L
UDIO  
VIDEO  
A
OUTPUT terminal ~  
• See page 35.  
Aerial socket !  
Connect the aerial cable.  
• See page 3.  
AUDIO  
L/MONO  
VIDEO  
S
R
OVER  
VIDEO-1  
VIDEO-2  
0
-
Y/VIDEO  
P
R/CR  
PB/CB  
VIDEO-3/  
COMPONENT  
AUDIO  
L/MONO  
=
~
R
R
OUTPUT  
L
VIDEO  
AUDIO  
!
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote control buttons and functions  
Turn the TV on from standby  
mode  
Press the POWER button.  
The POWER lamp lights red to green and  
MUTING  
POWER  
your TV will be turned on.  
SYSTEM  
CINEMA  
COLOUR SOUND SURROUND ZOOM  
• You can turn on the TV from the  
standby mode by pressing the TV/  
VIDEO button, the CHANNEL-/+  
buttons or the number buttons.  
PIP  
DISPLAY  
Except  
HV-29JH24  
HV-29VH14  
MENU  
OK  
TV/TEXT  
Except  
To turn the TV off:  
HV-29JH54  
HV-29VH14  
HV-29VH54  
TV/VIDEO  
Press the POWER button again.  
The POWER lamp changes from green to  
red and the TV enters standby mode.  
1
4
2
5
8
0
3
6
9
PICTURE  
MODE  
7
RETURN  
SUB-P  
Except  
HV-29JH24  
HV-29VH14  
+
Choose a TV channel  
Choose a programme number in which a  
TV channel has been set.  
CHANNEL  
VOLUME  
FAVORITE CH  
Press the CHANNEL-/+ buttons or enter  
the programme number (PR) with the  
number buttons.  
• If you want to put a two-digit channel  
into the TV, press the -/--button to  
change to the two-digit entry system.  
• You can select a channel from the PR  
LIST. For details, see “DISPLAY  
button” on page 11.  
• If you do not have a clear picture or no  
colour appears, follow the operation  
procedure “COLOUR SYSTEM button”  
on page 11.  
RM-C1350  
TV  
HV-29JH74  
FAVORITE CH  
Adjust the volume  
Press the VOLUME-/+ buttons.  
RM-C1351  
TV  
HV-29JH24  
FAVORITE CH  
Watch images from an  
external device  
Choose a VIDEO terminal to which the  
external device has been connected.  
RM-C1353  
TV  
HV-29JH54 / HV-29VH54  
Press the TV/VIDEO button.  
• You can choose a VIDEO terminal with  
the CHANNEL-/+ buttons or from the  
PR LIST.  
FAVORITE CH  
To return to a TV channel:  
Press the TV/VIDEO button, the  
CHANNEL-/+ buttons or the number  
buttons.  
HV-29VH14  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote control buttons and functions  
MUTING button  
Press the MUTING button to turn off the  
volume. Pressing the MUTING button again  
resumes the previous volume level.  
CINEMA SURROUND button  
You can enjoy an enhanced sound for a  
wider audience by using CINEMA  
SURROUND function.  
Press the CINEMA SURROUND button to  
select one of CINEMA SURROUND  
modes.  
ZOOM button  
You can change the screen size according  
to the picture aspect ratio. Choose the  
optimum one from the following ZOOM  
modes.  
HIGH/LOW:  
When you listen to the stereo sound, please  
select HIGH or LOW mode.  
You can enjoy the sound for a wider  
audience similar to the experience at the  
theatre.  
Press the ZOOM button to choose a  
mode.  
• The ZOOM button works only in the  
normal screen.  
• In case that you setting up the  
CINEMA SURROUND function to  
HIGH mode, there may be slight  
volume distortion. In case that occurs,  
please switch the HIGH mode to LOW  
mode, the effect of CINEMA  
SURROUND functions will be less  
noticeable, however, the volume  
distortion will be corrected.  
REGULAR:  
Use to view a normal picture (4:3 aspect  
ratio) as its original size is.  
ZOOM:  
You can zoom up the Wide picture (16:9  
aspect ratio) to fill the TV screen.  
MONO:  
Select the MONO mode, when you listen to  
the mono sound.  
You can enjoy the sound for a wider  
audience similar to stereo sound.  
OFF:  
The CINEMA SURROUND function  
switches off.  
• The left side and right side of the Wide  
picture (16:9 aspect ratio) will be cut  
off.  
PICTURE MODE button  
You can choose one of three PICTURE  
MODEs (three kinds of picture setting) to  
adjust the picture settings automatically.  
16:9:  
This mode converts a normal picture (4:3  
aspect ratio) into a Wide picture (16:9  
aspect ratio).  
Press the PICTURE MODE button to  
choose a mode.  
BRIGHT:  
Heightens contrast and sharpness.  
• Use for picture with a 16:9 aspect ratio  
that have been squeezed into a normal  
picture (4:3 aspect ratio), you can  
restore their original dimensions.  
STANDARD:  
Standardizes picture adjustment.  
SOFT:  
Softens contrast and sharpness.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote control buttons and functions  
RETURN function  
RETURN+ button  
The TV temporarily memorises the TV  
channel that was chosen right before the  
current TV channel as the “Last Channel”.  
By pressing the RETUTN+ button, you can  
alternately view the current TV channel and  
the “Last Channel”.  
The RETURN+ button has two functions;  
the RETURN+ function and the RETURN  
function. If a channel has been registered  
as the “Return Channel”, the RETURN+  
function operates. If there is no setting for  
the “Return Channel”, the RETURN function  
operates.  
• If you want to view two channels  
alternately by using the RETURN  
function, first choose one TV channel  
and then choose the other TV channel  
with the Number buttons. If you choose  
the TV channel without using the  
Number buttons, there are cases  
where a channel other than the one  
you first chose is registered as the  
“Last Channel”.  
RETURN+ function  
By registering a channel you frequently  
view as the “Return Channel”, you can  
select that channel at any time simply by  
pressing the RETURN+ button.  
To register a TV channel as the “Return  
Channel”:  
Choose the Programme number to which  
the channel you want to register has been  
set, and press the RETURN+ button and  
hold for more than 3 seconds continuously.  
“RETURN PLUS PROGRAMMED!” is  
displayed and the registration is completed.  
svt/ubutton  
When you are viewing a bilingual broadcast  
programme, you can choose the sound  
from Bilingual I (Sub I) or Bilingual II (Sub  
II).  
To cancel a TV channel registered as the  
“Return Channel”:  
• When the stereo broadcasting is  
received poorly, you can change from  
stereo to mono sound so that you can  
hear the broadcast more clearly and  
easily.  
While viewing any TV channel, press the  
RETURN+ button and hold for more than 3  
seconds continuously. “RETURN PLUS  
CANCELED!” is displayed and the  
registration is cancelled.  
Press the svt/ubutton to choose a  
• When you turn off the TV, the  
registration for the “Return Channel” is  
cancelled.  
sound mode.  
s
v
t
: Stereo sound  
: mono sound  
: Bilingual I (sub I)  
: Bilingual II (sub II)  
• If you want to view the “Return  
Channel” and another TV channel  
alternately, first choose a channel  
other than the “Return Channel”. And  
then press the RETURN+ button to  
change the channel to the “Return  
Channel” In this way, you can view two  
channels alternately by pressing the  
RETURN+ button.  
u
MONO : Cancels the Multi Sound function,  
and the sound becomes  
monaural.  
• The sound mode you can choose  
differs depending on the TV  
programme.  
• This function does not work in the  
VIDEO modes.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote control buttons and functions  
DISPLAY button  
COLOUR SYSTEM button  
The colour system is chosen automatically.  
However, if the picture is not clear or no  
colour appears, choose the colour system  
manually.  
You can display the PR LIST, programme  
number or VIDEO terminal number on the  
screen.  
Press the DISPLAY button.  
Press the DISPLAY button changes the  
display as follows:  
Press the COLOUR SYSTEM button to  
choose the appropriate colour system.  
AUTO:  
This function detects a colour system from  
the input signal.  
• The AUTO mode may not function  
properly if you have poor signal quality.  
If the picture is abnormal in the AUTO  
mode, choose another colour system  
manually.  
No indication  
• The AUTO mode detects a colour  
system from the input signal and  
chooses the appropriate colour system  
automatically.  
• For the colour systems in each country  
or region, see the table  
Choose a TV channel or a  
VIDEO terminal  
1 Press the DISPLAY button to display  
the PR LIST.  
“BROADCASTING SYSTEMS” on  
page 12.  
2 Press the 6and 5buttons to  
choose a programme number or  
VIDEO terminal.  
PAL/SECAM/NTSC3.58/NTSC4.43:  
PAL, SECAM, or NTSC colour system.  
Then press the MENU/OK button.  
• For programme numbers with the  
CHANNEL GUARD function set, the n  
(CHANNEL GUARD) mark is  
displayed next to the programme  
number in the PR LIST.  
• The VIDEO terminals are registered  
after the programme number PR99.  
• The AV channel (channel number 0) in  
the PR LIST will be chosen only if you  
connect the VCR to the TV with an  
aerial cable without connecting a video  
cable.  
SOUND SYSTEM button  
The sound system is chosen automatically.  
However, if you cannot hear the sound  
normally even when the picture appears  
normally, choose the sound system  
manually.  
Press the SOUND SYSTEM button to  
choose the appropriate sound system.  
B/G  
: B/G system  
I
: I system  
D/K  
M
: D/K system  
: M system  
• This function does not work in the  
VIDEO mode.  
• For the sound systems in each country  
or region, see the table  
“BROADCASTING SYSTEMS” on  
page 12.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote control buttons and functions  
BROADCASTING SYSTEMS  
For sound and colour systems in your  
country or region, refer to the table below:  
Favorite channel  
registration  
You can register your favorite TV channels  
with the colour buttons (Red, Green, Yellow  
and Blue). After registration you can recall  
the favorite channel by pressing the colour  
button.  
COLOUR SYSTEM  
Area  
Country or Region  
System  
PAL  
Bahrain, Kuwait, Oman,  
Qatar, United Arab Emirates,  
Yemen, etc.  
Indonesia, Malaysia,  
Singapore, Thailand, India,  
etc.  
1 In the normal screen, choose a TV  
channel (PR01-99) you want to  
register.  
Asia,  
Middle  
East  
China, Vietnam, etc.  
Hong Kong, etc.  
PAL  
PAL  
For detailed operation, see “Choose a  
TV channel” on page 8.  
Islamic Republic of Iran,  
Lebanon, Saudi Arabia, etc.  
SECAM  
2 Press and hold a colour button for 3  
seconds or more.  
Philippines, Taiwan,  
Myanmar, etc.  
NTSC  
Then “FAVORITE CHANNEL  
Russia, etc.  
SECAM  
PROGRAMMED!” appears on the screen  
and the current channel is registered.  
• If the chosen channel is already  
registered as the favorite channel,  
when a colour button is pressed, the  
registered colour button icon appears  
on the top right of the screen.  
Czech Republic, Poland, etc. PAL  
Europe  
Germany, Holland, Belgium,  
etc.  
UK, etc.  
PAL  
PAL  
Oceania Australia, New Zealand, etc. PAL  
Republic of South Africa, etc. PAL  
Africa  
Nigeria, etc.  
PAL  
Egypt, Morocco, etc.  
SECAM  
SOUND SYSTEM  
• You cannot register in the Text mode,  
or while multiple screens, such as PIP  
(picture in picture) are displayed.  
• Also you cannot register if the chosen  
channel is guarded with the CHANNEL  
GUARD function and the screen is  
blue, or if an on-screen menu is  
displayed.  
Area  
Country or Region  
System  
B/G  
Bahrain, Kuwait, Oman,  
Qatar, United Arab Emirates,  
Yemen, etc.  
Indonesia, Malaysia,  
Singapore, Thailand, India,  
etc.  
China, Vietnam, etc.  
Hong Kong, etc.  
Asia,  
Middle  
East  
D/K  
I
Islamic Republic of Iran,  
• Even if you perform AUTO PROGRAM  
function, the registration made here  
will not be changed. (For AUTO  
PROGRAM, see page 29.)  
B/G  
Lebanon, Saudi Arabia, etc.  
Philippines, Taiwan,  
Myanmar, etc.  
Russia, etc.  
M
D/K  
Czech Republic, Poland, etc. D/K  
Recalling the favorite channel  
Press the colour button, then the registered  
favorite channel will be displayed.  
Europe  
Germany, Holland, Belgium,  
B/G  
etc.  
UK, etc.  
Oceania Australia, New Zealand, etc. B/G  
I
• You cannot recall the favorite channel  
in the Text mode, Menu mode where  
an on-screen menu is displayed, or  
while multiple screens are displayed.  
Republic of South Africa, etc.  
Nigeria, etc.  
Egypt, Morocco, etc.  
I
Africa  
B/G  
B/G  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote control buttons and functions  
• The picture effect dedicated for the  
colour button applies. For details, see  
“Setting the picture effect” below:  
Viewing a teletext  
programme  
[Except HV-29JH54/HV-29VH14/  
HV-29VH54]  
Setting the picture effect  
Each colour button has a dedicated picture  
effect. When you choose a favorite channel,  
the dedicated picture effect is used. When  
shipped, the factory set picture effect is  
used for this purpose. However, you can set  
this picture effect as required. For details,  
see “FAVORITE CH SETTING” on page 24.  
1 Choose a TV channel with a teletext  
broadcast.  
2 Press the TV/TEXT button.  
Pressing the TV/TEXT button changes  
the mode as follows:  
Showing the favorite channels  
Press the DISPLAY button to display the  
PR LIST.  
You can see the favorite channel that has  
the registered colour button icon at the right  
of the channel number.  
TV and  
Text mode  
TV mode  
Text mode  
ZDF  
BBC1  
3 Choose a teletext page by pressing  
the CHANNEL-/+ buttons, number  
buttons or colour buttons.  
To return to the TV mode:  
Press the TV/TEXT button or TV/VIDEO  
button.  
• If you have trouble receiving teletext  
broadcasts, consult your local dealer  
or the broadcast station.  
• In the Text mode, the ZOOM mode is  
fixed to the REGULAR mode.  
• No menu operations are possible  
when viewing a teletext programme.  
• If characters on a teletext programme  
do not appear properly, change the  
TELETEXT LANGUAGE setting. For  
details, see “TELETEXT LANGUAGE”  
on page 34.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote control buttons and functions  
3 Press the  
(Cancel) button to  
(Hold) button  
return to a teletext page when the  
page number is on the screen.  
• You cannot return to the TV mode with  
You can hold a teletext page on the screen  
for as long as you want, even while several  
other teletext pages are being received.  
the  
(Cancel) button.  
Press the  
(Hold) button.  
(Sub-page) button  
The (hold) are displayed at the top left  
Some teletext pages include sub-pages that  
are automatically displayed. You can hold  
any sub-page, or view it at any time.  
of the screen.  
To cancel the Hold function:  
Press the  
(Hold) button again.  
1 Press the  
(Sub-page) button to  
operate the Sub-page function.  
Sub-page numbers are displayed at the  
left of the screen.  
(Reveal) button  
Some teletext pages include hidden text  
(such as answers to a quiz).  
You can display the hidden text.  
Colour* Meaning of sub-page number  
Each time you press the  
button, text is hidden or revealed.  
(Reveal)  
Yellow  
White  
Currently being displayed.  
Can be displayed.  
(Size) button  
You can double the height of teletext  
display.  
Blue or  
Red  
Cannot be displayed and it is not  
sent.  
*: Background colour of the sub-page  
number.  
Press the  
(Size) button.  
2 Press the CHANNEL-/+ buttons to  
choose a sub-page number.  
(Index) button  
You can return to the index page instantly.  
To cancel the  
(Sub-page) function:  
Press the (Index) button.  
Press the  
(Sub-page) button again.  
• In the List mode, you can return to the  
page number displayed in the lower  
left area of the screen.  
(Cancel) button  
You can search for a teletext page while  
watching TV.  
1 Press the number button to enter a  
page number, or press the colour  
button.  
The TV searches for a teletext page.  
2 Press the  
(Cancel) button.  
The TV programme appears. When the  
TV finds the teletext page, its page  
number appears in the upper left of the  
screen.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote control buttons and functions  
Using the List mode  
Twin and PIP (picture in  
picture) function  
You can store the numbers of your favorite  
teletext pages in memory and call them up  
quickly using the colour buttons.  
[Except HV-29JH24/HV-29VH14]  
You can display two different pictures, the  
main picture and sub picture, at a time. In  
Twin mode, both pictures are equal in size.  
In PIP mode, the small sub picture appears  
at a corner of the screen. You can swap the  
main picture and sub picture instantly. Note  
that the main and sub pictures use different  
input sources each other. For example, if  
the main picture’s source is TV, the sub  
picture’s one will be VIDEO.  
To store the page numbers:  
1 Press the MODE button to engage the  
List mode.  
The stored page numbers are displayed  
at the bottom of the screen.  
2 Press a colour button to choose a  
position. Then press the number  
buttons to enter the page number.  
3 Press and hold down the  
button.  
(Store)  
While watching a normal picture, press  
the PIP button.  
Pressing the PIP button changes the mode  
The four page numbers blink white to  
indicate that they are stored in memory.  
as follows:  
To call up a stored page:  
1 Press the MODE button to engage the  
List mode.  
Twin mode  
Normal screen  
Sub  
2 Press a colour button to which a page  
has been assigned.  
Main  
PIP mode  
To exit the List mode:  
Press the MODE button again.  
Sub  
Main  
• You can also enter this mode while in  
the Multi-display mode, Freeze mode  
or Strobe mode, except in the Text  
mode.  
To return to the normal screen:  
Press the PIP button until the sub picture  
disappears.  
• You can hear the sound from the main  
picture only.  
• In the normal screen, if the current  
channel is guarded with the CHANNEL  
GUARD function and the screen is  
blue, the PIP button does not work.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote control buttons and functions  
• When you exit the Twin or PIP mode,  
the sub picture lastly displayed will be  
saved, and it will appear next time.  
• The following table shows what will  
happen if the same input sources are  
chosen for both main and sub pictures  
when you enter the Twin or PIP mode.  
If the main picture is the same as the sub  
picture, then the sub picture will be  
changed to VIDEO-1. But if the main  
picture is VIDEO-1, then the sub picture  
will be changed to VIDEO-2.  
For the sub picture:  
Press the  
(Input) button.  
Each time you press the button, the input  
source changes as follow (the one used for  
the main picture will be skipped):  
VIDEO-1 VIDEO-2 VIDEO-3 →  
VIDEO-4 TV  
Swapping the pictures  
Press the  
(Swap) button.  
Each time you press the button, the main  
picture and the sub picture will be swapped.  
[When the same input sources are chosen]  
Changing the sub picture  
position (in PIP mode only)  
You can position the sub picture to one of  
corners of the main picture.  
Main picture  
TV  
Sub picture  
TV VIDEO-1  
VIDEO-1  
VIDEO-2  
VIDEO-3  
VIDEO-4  
VIDEO-1 VIDEO-2  
VIDEO-2 VIDEO-1  
VIDEO-3 VIDEO-1  
VIDEO-4 VIDEO-1  
Press the  
(Position) button.  
Each time you press the button, the sub  
picture moves clockwise (lower right →  
lower left upper left upper right).  
• If you press the PIP button when  
receiving the Progressive Video Signal  
(525P or 625P signal), "525P" or  
“625P” appears on the screen and the  
Twin/PIP function does not operate.  
Setting the colour system of the  
sub picture  
You can choose the colour system of the  
sub picture.  
While the sub picture is being displayed,  
press the C.SYS button.  
Each time you press the button, the colour  
system of the sub picture changes as  
follows:  
AUTO PAL SECAM NTSC3.58 →  
NTSC4.43  
TV channel selection  
For the main picture:  
Choose a channel using the CHANNEL-/+  
buttons or the number buttons.  
For the sub picture:  
Choose a channel using the SUB-P-/+  
buttons.  
• For all source, normally choose AUTO.  
• The chosen colour system will not be  
saved.  
• If the main picture and the sub picture  
are of different colour systems, there  
will be some differences in the size of  
the sub picture and flicker may take  
place.  
Input source selection (TV,  
VIDEO-1, -2, -3 or -4)  
For the main picture:  
Press the TV/VIDEO button.  
Each time you press the button, the input  
source changes as follows (the one used for  
the sub picture will be skipped):  
VIDEO-1 VIDEO-2 VIDEO-3 →  
VIDEO-4 TV  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote control buttons and functions  
in the Multi-display mode.  
Multi-display function  
• If you press the MULTI button when  
receiving the Progressive video signal  
(525P or 625P signal), "525P" or  
“625P” appears on the screen and the  
MULTI function does not operate.  
[Except HV-29JH24/HV-29VH14]  
You can watch nine different TV  
programmes at a time. As you can display  
nine TV programmes successively, this  
function is convenient to locate the TV  
programme you want. Eight pictures are still  
pictures and the last one is the moving  
picture with the blue frame. You can choose  
any picture as the moving picture and then  
watch it in the normal screen.  
Returning to the normal screen  
Press the MULTI button or MENU/OK  
button, or choose a TV channel with the  
number buttons.  
The moving picture with the blue frame will  
be displayed in the normal screen.  
• Pressing the TV/VIDEO button will also  
returns the TV to the normal screen.  
Entering the Multi-display mode  
While watching a TV programme in the  
normal screen, press the MULTI button.  
The screen changes to the multi-picture  
screen and nine pictures are displayed in  
the numerical order.  
Choosing a picture as the  
moving one  
You can choose one of the pictures as the  
moving picture with the blue frame.  
Press 5and 6buttons to move the  
blue frame.  
The chosen picture becomes the moving  
picture.  
• Pressing the 3button in the right-most  
position “3” or “6” will scroll the blue  
frame to the next position, “4” or “7”.  
While, pressing the 2button in the left-  
most position “4” or “7” will scroll the  
blue frame to the previous position, “3”  
or “6”.  
Moving picture with the blue frame  
You can also enter this mode while in the  
Twin mode, but not in the Text mode.  
Displaying the next nine pictures  
• Pictures will appear in the assigned  
order in the PR LIST (PR01-99).  
• If the number of pictures to be  
displayed at a time is less than nine,  
fewer pictures than nine will be  
displayed.  
• The guarded channel with the  
CHANNEL GUARD function will be  
skipped and will not be displayed.  
• You cannot display a video image in  
the Multi-display mode.  
Press the NEXT button.  
The next nine pictures will be displayed at a  
time. By pressing the NEXT button  
successively, you can display all available  
pictures except video images.  
Displaying the channel numbers  
on the multi-display screen  
Press the DISPLAY button.  
Respective channel numbers appear on the  
nine pictures.  
• The RETURN+ button, svt/ubutton,  
COLOUR SYSTEM button and  
SOUND SYSTEM button are disabled  
To go off the channel numbers:  
Press the DISPLAY button again.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote control buttons and functions  
Freeze function  
Strobe function  
[Except HV-29JH24/HV-29VH14]  
[Except HV-29JH24/HV-29VH14]  
While watching a picture, you can capture a  
still picture you want. The captured still  
picture and the moving picture are  
displayed at a time. (They are the pictures  
of the same source.)  
You can display eight consecutive still  
pictures and one moving picture at a time.  
(They are the pictures of the same source.)  
Press the STROBE button.  
Eight consecutive still pictures which are  
captured at intervals of about 0.2 second  
are displayed in the order of “1” to “9”.  
(These numbers are not actually displayed.)  
Press the  
(Freeze) button.  
Still picture is captured and displayed on the  
right side of the screen. On the left, the  
moving picture is displayed.  
Still  
picture  
Moving  
picture  
• The  
(Freeze) button does not work  
in the Text mode.  
To return to the normal screen:  
• The STROBE button does not work in  
the Text mode.  
Press the  
(Freeze) button again or  
press the number buttons to choose a  
channel.  
To return to the normal screen:  
Press the STROBE button again or press  
the number buttons to choose a channel.  
• If signal level of the main picture is  
weak, the still images become  
• You cannot use the FREEZE button  
when the sub picture or the main  
picture are displayed on the screen.  
• If the current channel is guarded with  
the CHANNEL GUARD function and  
the screen is blue, this button does not  
work.  
• If you press the FREEZE button when  
receiving the Progressive video signal  
(525P or 625P signal), "525P" or  
“625P” appears on the screen and the  
FREEZE function does not operate.  
abnormal.  
• You cannot use the STROBE button  
when the sub picture or the main  
picture are displayed on.  
• If the current channel is guarded with  
the CHANNEL GUARD function and  
the screen is blue, the STROBE button  
does not work.  
• If you press the STROBE button when  
receiving the Progressive video signal  
(525P or 625P signal), "525P" or  
“625P” appears on the screen and the  
STROBE function does not operate.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the TV’s menu  
This TV has a number of functions you can operate using menus.  
To fully utilize all your TV’s functions, you need to understand the basic menu operating  
techniques fully.  
• The following remote control is for HV-29JH74. However, the buttons used for setting TV  
menus are common to all models.  
Basic operation  
1 Press the MENU/OK button to display  
the MENU (main menu).  
MUTING  
POWER  
SYSTEM  
CINEMA  
COLOUR SOUND SURROUND ZOOM  
PIP  
DISPLAY  
• The display appearing at the bottom of  
a menu indicates buttons on the  
remote control you can use when you  
operate a chosen function.  
MENU  
OK  
TV/TEXT  
MENU/OK button  
OK  
TV/VIDEO  
1
4
2
5
8
0
3
6
9
TV/VIDEO button  
DISPLAY button  
TV  
PICTURE  
MODE  
DISP.  
7
RETURN  
2 Press the 6buttons or 5to  
choose a menu title, and press the  
MENU/OK button.  
SUB-P  
+
CHANNEL  
VOLUME  
The menu appears.  
FAVORITE CH  
To return to the previous menu:  
Press the DISPLAY button.  
To exit a menu instantly:  
Press the TV/VIDEO button.  
3 Press the 6buttons to choose a  
function.  
RM-C1350  
TV  
• For details of the functions in the  
menus, see the following pages.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the TV’s menu  
4 Press the 5buttons to choose the  
setting of that function.  
PICTURE SETTING menu  
• If you want to operate a function which  
appears only with its name, follow the  
descriptions of that function on the  
following pages.  
• The display appearing at the bottom of  
a menu shows you a button on the  
remote control that you can use when  
you operate a chosen function.  
PICTURE MODE  
5 Press the MENU/OK button to  
complete the setting.  
You can choose one of three PICTURE  
MODEs to adjust the picture settings  
automatically.  
The menu disappears.  
• When watching the television with the  
NTSC system, the menus as displayed  
at about half of their normal vertical  
size.  
BRIGHT:  
Heightens contrast and sharpness.  
STANDARD:  
Standardizes picture adjustment.  
Operation with the buttons on the  
TV  
SOFT:  
You can also operate the menus using the  
buttons on the front panel of the TV.  
Softens contrast and sharpness.  
• You can also operate the PICTURE  
MODE function with the PICTURE  
MODE button on the remote control.  
For details, see “PICTURE MODE  
button” on page 9.  
HV-29JH24/HV-29JH54/HV-29JH74  
MENU  
CHANNEL  
VOLUME TV/VIDEO  
Adjusting the picture  
You can change the picture settings of each  
picture mode, as you like. The picture  
settings changed are stored in the picture  
mode.  
OK  
EXIT  
OK  
6
5
TV/VIDEO  
buttons buttons buttons buttons  
CONTRAST  
HV-29VH14/HV-29VH54  
You can adjust the picture contrast.  
2: lower  
3: higher  
OK  
6
5
TV/VIDEO  
buttons buttons buttons buttons  
BRIGHT  
You can adjust the picture brightness.  
2: darker  
3: brighter  
MENU  
OK  
CHANNEL  
VOLUME TV/VIDEO  
EXIT  
SHARP  
• There is no DISPLAY button on the  
front panel of the TV, which will be  
used for menu operation.  
You can adjust the picture sharpness.  
2: softer  
3: sharper  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the TV’s menu  
COLOUR  
You can adjust the picture colour.  
PICTURE FEATURES menu  
2: lighter  
3: deeper  
TINT  
You can adjust the picture tint.  
2: reddish  
3: greenish  
• You can change the TINT setting  
(picture tint) only when the colour  
system is NTSC 3.58 or NTSC 4.43.  
• You cannot select the TINT function  
when receiving the Progressive video  
signal (525P and 625P signals).  
DIGITAL VNR  
The DIGITAL VNR function cuts down the  
amount of noise in the original picture.  
To return to the default settings in each  
PICTURE MODE:  
Press the blue button. This will return the  
picture settings in the currently chosen  
PICTURE MODE to the default settings,  
and stores them in the PICTURE MODE  
again.  
AUTO:  
The TV will be automatically adjust the level  
of the DIGITAL VNR effect to match the  
amount of noise in the picture, giving you  
the best possible picture.  
• If you set the DIGITAL VNR effect too  
high it can make the picture less sharp.  
It is recommended to use the AUTO  
setting if you can.  
WHITE BALANCE  
You can select one of three WHITE  
BALANCE modes (three tones of white) to  
adjust the white balance of the picture.  
Since white is the colour which is used as a  
reference for all the other colours, changing  
the WHITE BALANCE mode affects the  
appearance of all the other colours on the  
screen.  
MAX:  
The level of the DIGITAL VNR effect is set  
to the maximum. If you set the DIGITAL VNR  
function to AUTO but still notice some noise,  
change the setting from AUTO to MAX.  
• The MAX setting is not suitable for  
high-quality pictures which contain a  
lot of noise.  
COOL:  
A bluish white. Using this mode when  
watching bright pictures allows you to enjoy  
a more vivid and bright picture.  
OFF:  
The level of the DIGITAL VNR effect is set  
to OFF.  
MID:  
The normal white colour.  
MIN:  
WARM:  
The level of the DIGITAL VNR effect is set to  
the minimum. If you set the DIGITAL VNR  
function to AUTO but feel that the sharpness  
of the original picture has not been reproduced  
fully, change the setting from AUTO to MIN.  
• The MIN setting is not suitable for low-  
quality pictures which contain a lot of noise.  
A radish white. Using this mode when  
watching films allows you to enjoy colours  
that are characteristic of films.  
• You cannot select the WHITE  
BALANCE function in the 16:9 mode  
of the ZOOM function.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the TV’s menu  
MIN:  
DigiPure  
The level of the DigiPure effect is set to the  
minimum. When you set the DigiPure  
function to AUTO and notice some noise,  
change the setting from AUTO to MIN.  
• The MIN setting is not suitable for  
high-quality pictures which contain  
very little noise.  
The Digipure function uses the latest in  
digital technology to give you a natural  
looking picture. The Digipure function  
includes the following two functions.  
Digipure function:  
This function helps to create a natural  
looking picture by eliminating unnecessary  
edges from high-contrast and crisp images.  
Conversely, for images with low-contrast,  
edges are added to produce a sharper,  
more detailed picture.  
PULL DOWN  
The PULL DOWN function displays a  
cinema film picture more smoothly and  
naturally on the screen.  
You can choose from the DigiPure function  
settings of AUTO, MIN and MAX.  
AUTO:  
This function is turned on. Normally keep  
Picture motion compensation function:  
This function displays fast-moving pictures  
(for example, the players or ball in a football  
game) more smoothly and naturally on the  
screen.  
this function set to AUTO.  
ON :  
This function is turned on.  
OFF:  
This function is turned off.  
AUTO:  
• The motion may appear unnatural  
when viewing images with the NTSC  
colour system. To make the motion  
smoother, switch the PULL DOWN  
function from AUTO or ON to OFF.  
• You cannot select this function in the  
Twin pictures mode.  
• You cannot select this function when  
receiving the Progressive video signal  
(525P and 625P signals).  
The TV will automatically adjust the level of  
the DigiPure effect to match the amount of  
noise in the picture, giving the best possible  
picture.  
• If you set the DigiPure effect too high  
on a low-quality picture that contains a  
lot of noise, this may actually make the  
noise worse. It is recommended to use  
the AUTO setting if you can.  
MAX:  
When TV displays Twin, PIP, Multi-display,  
FREEZE, or STROBE function, PULL  
DOWN function cannot operate.  
The level of the DigiPure effect is set to the  
maximum. If you set the DigiPure function  
to AUTO but feel that the original picture  
quality has not been reproduced fully,  
change the setting from AUTO to MAX.  
• The MAX setting is not suitable for  
low-quality pictures which contain a lot  
of noise.  
OFF:  
The DigiPure function is turned off.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the TV’s menu  
COLOUR SYSTEM  
ZOOM  
The colour system is chosen automatically.  
However, if the picture is not clear or no  
colour appears, choose the colour system  
manually.  
You can change the screen size according  
to the picture aspect ratio. Choose the  
optimum one from three ZOOM modes.  
1 Choose ZOOM, then press the MENU/  
OK button.  
1 Choose COLOUR SYSTEM, then  
press the 5buttons to choose the  
appropriate colour system.  
• You can also operate the COLOUR  
SYSTEM function with the COLOUR  
SYSTEM button on the remote control.  
For details, see “COLOUR SYSTEM  
button” on page 11.  
2 Press the 6buttons to choose a  
ZOOM mode. Then press the MENU/  
OK button.  
• You can choose a ZOOM mode from  
REGULAR, ZOOM or 16:9 modes. For  
details, see “ZOOM button” on page 9.  
PICTURE TILT  
There are cases where the Earth’s  
magnetic force may make the picture tilt. If  
this happens, you can correct the picture tilt.  
1 Choose PICTURE TILT, then press the  
MENU/OK button.  
2 Press the 6buttons until the  
picture becomes level. Then press the  
MENU/OK button.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the TV’s menu  
• For details of each item, see  
“PICTURE MODE” on page 20,  
“DIGITAL VNR” on page 21, “WHITE  
BALANCE” on page 21, “DigiPure” on  
page 22.  
FAVORITE CH SETTING  
You can set a dedicated picture effect for  
the favorite channels registered to the  
colour buttons (Red, Green, Yellow and  
Blue). For favorite channel registration, see  
“Favorite channel registration” on page 12.  
Item  
Options  
1 Choose FAVORITE CH SETTING, then  
press the MENU/OK button.  
PICTURE MODE BRIGHT*, STANDARD,  
SOFT  
DIGITAL VNR  
AUTO*, MAX, OFF, MIN  
COOL, MID*, WARM  
WHITE  
BALANCE  
DigiPure  
AUTO*, MAX, OFF, MIN  
PICTURE  
EFFECT  
ON*:  
Above picture effect  
applies to the chosen  
favorite channel.  
OFF:  
No picture effect applies.  
2 Press the 6button to choose  
FAVORITE CHANNEL, then press the  
5button to choose the registered  
favorite channel.  
*: When shipped  
4 Press the MENU/OK button to  
complete the setting.  
Each time you press the 5button, the  
colour button icon (Red, Green, Yellow  
or Blue) of the registered favorite  
channel and its channel number (e.g.  
PR1) appear.  
VIDEO SETTING  
You can set a dedicated picture effect for  
the video inputs, VIDEO-1 to -4.  
1 Choose VIDEO SETTING, then press  
the MENU/OK button.  
3 Set the picture effect.  
Press the 6button to choose an item  
listed in the following table and press the  
5button to choose one of options.  
• As explained in the table, if PICTURE  
EFFECT is set to OFF, the dedicated  
picture effect for the favorite channel is  
not used. In this case, normal picture  
effect is used.  
2 Press the 6button to choose  
VIDEO STATUS, then press the 5  
button to choose one of video inputs,  
VIDEO-1 to -4.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the TV’s menu  
3 Set the picture effect.  
SOUND SETTING menu  
Press the 6button to choose an item  
listed in the following table and press the  
5button to choose one of options.  
• As explained in the table, the  
PICTURE EFFECT for the video inputs  
is set to OFF when shipped. To use it,  
you need to set it ON.  
Item  
Options  
STEREO / I•II  
PICTURE MODE BRIGHT*, STANDARD,  
SOFT  
When you are viewing a bilingual broadcast  
programme, you can choose the sound  
from Bilingual I (sub I) or Bilingual II (sub II).  
When the stereo broadcasting is received  
poorly, you can change from stereo to mono  
sound so that you can hear the broadcast  
more clearly and easily.  
DIGITAL VNR  
AUTO*, MAX, OFF, MIN  
COOL, MID*, WARM  
WHITE  
BALANCE  
DigiPure  
AUTO*, MAX, OFF, MIN  
PICTURE  
EFFECT  
ON:  
s :Stereo sound  
Above picture effect  
applies to the chosen  
video input.  
v
t
u
: mono sound  
: Bilingual I (sub I)  
: Bilingual II (sub II)  
OFF*:  
No picture effect applies.  
MONO: Cancels the Multi Sound function,  
and the sound becomes monaural.  
• The sound mode you can choose  
differs depending on the TV  
programme.  
*: When shipped  
• For details of each item, see  
“PICTURE MODE” on page 20,  
“DIGITAL VNR” on page 21, “WHITE  
BALANCE” on page 21, “DigiPure” on  
page 22.  
• Pressing the number button “0” will  
return the picture effect to the factory  
set value.  
• This function does not work in the  
VIDEO modes.  
• You can also operate the STEREO /  
I•II function with the svt/ubutton.  
For details, see “svt/ubutton” on  
page 10.  
4 Press the MENU/OK button to  
complete the setting.  
Adjusting the sound  
You can adjust the sound to your liking.  
BASS  
You can adjust the low tone of the sound.  
2: weaker  
3: stronger  
TREBLE  
You can adjust the high tone of the sound.  
2: weaker  
3: stronger  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the TV’s menu  
BALANCE  
FEATURES menu  
You can adjust the volume balance  
between the left and right speakers.  
2: turn the left speaker’s volume level up.  
3: turn the right speaker’s volume level up.  
AI VOLUME  
You can prevent the sudden increase or  
decrease of sound that occurs when  
changing the channel to another channel or  
switching the VIDEO mode to another  
VIDEO mode.  
SLEEP TIMER  
You can set the TV to automatically turn off  
after a set time.  
ON:  
1 Choose SLEEP TIMER, then press the  
MENU/OK button.  
This function is turned on.  
OFF:  
This function is turned off.  
• The AI VOLUME function may not  
operate as expected if the sound input  
level from a broadcast station (or video  
software) is extremely low.  
CINEMA SURROUND  
You can enjoy Surround sound with a “live”  
effect by using the CINEMA SURROUND  
function.  
2 Press the 5buttons to set the  
period of time.  
The TV begins count down from the set  
time.  
• You can choose a CINEMA  
SURROUND mode from HIGH, LOW,  
MONO and OFF modes. For details,  
see “CINEMA SURROUND button” on  
page 9.  
• You can also operate the CINEMA  
SURROUND function with the  
CINEMA SURROUND button. For  
details, see “CINEMA SURROUND  
button” on page 9.  
• You can set the period of time a  
maximum of 120 minutes (2 hours) in  
10 minute steps.  
To cancel this function:  
• Press the 2button to set a period of  
time to “OFF”.  
3 Press the MENU/OK button to  
complete the setting.  
The menu disappears.  
• One minute before this function turns  
off the TV, “GOOD NIGHT!” appears.  
• This function cannot be used to turn off  
the TV’s main power.  
• When this function is on, you can  
display the SLEEP TIMER menu again  
to confirm or change the remaining  
time.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the TV’s menu  
2 Set the ID number you want.  
BLUE BACK  
You can set the TV to automatically change  
to a blue screen and mute the sound if the  
signal is weak or absent, or when there is  
no input from an external device.  
To choose a number:  
Press the 6buttons.  
To move a cursor:  
Press the 5buttons.  
ON:  
3 Press the MENU/OK button.  
This function is turned on.  
OFF:  
This function is turned off.  
CHILD LOCK  
You can disable the front control buttons of  
the TV. When this function is set to ON, the  
TV can be operated only by using the  
remote control.  
Use this function to prevent children from  
operating the TV at their own discretion  
(without parent consent).  
4 Press the 6buttons to choose a TV  
channel.  
• The TV shows the TV programme  
which the chosen TV channel is now  
broadcasting.  
ON:  
This function is turned on.  
OFF:  
5 Press the blue button to set this  
function to the TV channel.  
This function is turned off.  
n(CHANNEL GUARD) appears and the  
TV channel is locked.  
CHANNEL GUARD  
When there is a TV channel you do not  
want your children to watch, you can lock  
out the channel. Even when a child chooses  
a programme number for a locked out  
channel the screen will change to blue and  
display nso the channel cannot be viewed.  
To cancel this function:  
Press the blue button again.  
n(CHANNEL GUARD) disappears and  
the lock is released.  
6 Press the MENU/OK button to  
complete the setting.  
To set this function:  
1 Choose CHANNEL GUARD, then  
press the number 0 (AV) button.  
The menu disappears.  
To view a locked TV channel:  
1 Choose a programme number in  
which a TV channel locked with the  
number buttons or PR LIST.  
The screen changes to blue and the n  
(CHANNEL GUARD) appears.  
• You cannot choose a locked TV  
channel with the 6buttons.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the TV’s menu  
2 Press the DISPLAY button to display  
“ID NO.” (ID number input screen).  
“Additional preparation” on page 35.  
This Television is compatible with the  
Progressive video signal (525P signal  
and 625P signal) only when the  
component video signal is input.  
PIP  
3 Press the number buttons to enter the  
ID number.  
[Except HV-29JH24/HV-29VH14]  
You can enter the Twin or PIP mode from  
the menu without using the remote control.  
This menu will be useful if you cannot find  
the remote control around you.  
The lock is temporarily released so you  
can view the TV channel.  
If you have forgotten the ID number:  
Perform step 1 of “To set this function:” on  
page 27. After confirming the ID number,  
press the TV/VIDEO button to exit the menu.  
• For detailed description of Twin and  
PIP mode, see “Twin and PIP (picture  
in picture) function” on page 15.  
1 Choose PIP, then press the MENU/OK  
button.  
• When you would like to cancel the  
CHANNEL GUARD function, you must  
perform the operation “To set this  
function” again.  
AUTO SHUTOFF  
You can set your TV to turn off if no signal is  
received for about 15 minutes or longer  
after the end of a broadcast.  
2 Display Twin or PIP picture as you like.  
First press the 6 button to choose an  
item listed, then press the 5 button to  
choose one of options, then press the  
MENU/OK button.  
ON:  
This function is turned on.  
OFF:  
This function is turned off.  
• The AUTO SHUTOFF function does  
not turn off the TV’s main power.  
• The AUTO SHUTOFF will not work for  
a VIDEO mode.  
PIP/TWIN  
Each time you press the 5 button, the  
screen mode changes as follows:  
TWIN  
PIP  
OFF (normal screen)  
SUB INPUT  
VIDEO-3 SETTING  
Each time you press the 5 button, the  
input source of the sub picture changes as  
follows:  
Set the VIDEO-3 SETTING correctly  
according to the video signal input from the  
external device connected to the VIDEO-3  
terminal. If this setting is incorrect, images  
will not be displayed.  
VIDEO-1  
VIDEO-2  
TV  
VIDEO-3  
VIDEO-4  
VIDEO:  
SWAP  
If a normal video signal (composite video  
Each time you press the MENU/OK button,  
the main picture and the sub picture will be  
swapped.  
signal) is input.  
COMPONENT:  
If a Component video signal (Y/CB/CR  
signals) is input.  
• If PIP/TWIN is selected OFF, then  
SUB INPUT and SWAP disappears in  
PIP menu.  
• For detailed connecting methods, see  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the TV’s menu  
INSTALL menu  
• To stop the AUTO PROGRAM  
function, press the MENU/OK button.  
LANGUAGE  
2 After the TV channels have been  
stored in the programme number list,  
the EDIT menu appears.  
You can choose the language you want to  
use for the on-screen display from the  
language list in a menu.  
1 Choose LANGUAGE, then press the  
MENU/OK button.  
2 Press the 6buttons to choose a  
language.  
3 Press the MENU/OK button to  
complete the setting.  
• You can proceed to edit the  
programme numbers list using the  
EDIT/MANUAL function. For details,  
see “EDIT/MANUAL” on page 30.  
• If a TV channel you want to view is not  
stored in the programme numbers list,  
you can register it using the MANUAL  
function.  
The menu disappears.  
AUTO PROGRAM  
You can automatically register the TV  
channels which can be received well at your  
residence in the TV’s programme numbers  
by performing the following.  
1 Choose AUTO PROGRAM, then press  
the MENU/OK button.  
For details, see “EDIT/MANUAL” on  
page 30.  
The AUTO PROGRAM function starts.  
The TV channels you receive are  
automatically stored in the programme  
numbers list.  
• The AUTO PROGRAM function does  
not store a TV channel to the  
programme number 0 (AV).  
• If you do not need to use the EDIT/  
MANUAL function, press the MENU/  
OK button to exit the EDIT menu.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the TV’s menu  
INSERT:  
EDIT/MANUAL  
This function adds a new TV channel in  
the current programme numbers list by  
using the CH/CC number.  
The EDIT/MANUAL functions are divided  
into two types: editing of the current  
programme numbers (EDIT functions) and  
manual registration of a TV channel you  
want to view to the programme number  
(MANUAL function).  
DELETE:  
This function deletes an unnecessary TV  
Channel.  
MANUAL:  
This function manually registers a new  
TV channel in a programme number.  
CAUTION  
• Using the MOVE, DELETE or INSERT  
function rewrites the current programme  
numbers list.  
Resultingly, the programme number of  
some of the TV channels will change.  
• When a TV channel which has been  
locked out using the CHANNEL GUARD  
function, using the MANUAL function for  
that TV channel cancels the CHANNEL  
GUARD function.  
3 Press the MENU/OK button to  
complete the setting.  
• For programme number PR 0, “AV”  
appears in the programme numbers  
list.  
FUNCTIONS  
MOVE  
• When a TV channel has already been  
registered in PR 99, using the INSERT  
function deletes the TV channel.  
1 Press the 6buttons to choose a TV  
channel.  
1 Choose EDIT/MANUAL, then press the  
MENU/OK button.  
2 Press the 3button to start the MOVE  
function.  
3 Press the 6buttons to choose a  
new programme number.  
2 Follow the operation description of a  
function you want to use and operate  
the function.  
To cancel the MOVE function:  
Press the DISPLAY button.  
4 Press the 2button to change the  
programme number of a TV channel  
to a new programme number.  
MOVE:  
This function changes a programme  
number of a TV channel.  
ID:  
This function registers a Channel name  
(ID) to a TV channel.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the TV’s menu  
ID  
1 Press the 6buttons to choose a TV  
channel.  
2 Press the red button to start the ID  
function.  
3 Enter a channel name (ID). Press the  
6buttons to choose a character.  
Press the 5buttons to move the  
cursor.  
To cancel the MANUAL function:  
Press the DISPLAY button.  
3 Press the 3button to choose the  
system (sound system) for a TV  
channel you want to register.  
• For the sound systems in each country  
or region, see the table  
“BROADCASTING SYSTEMS” on  
page 12.  
To cancel the ID function:  
Press the DISPLAY button.  
4 Press the green or red button to  
search for a TV channel.  
4 Press the MENU/OK button to register  
a channel name to a TV channel.  
Scanning stops when the TV finds a TV  
channel. Then the TV channel is  
displayed.  
DELETE  
1 Press the 6buttons to choose a TV  
5 Press the green or red button  
repeatedly until the TV channel you  
want appears.  
channel.  
2 Press the yellow button to delete the  
TV channel.  
If the TV channel reception is poor:  
Press the blue or yellow button to fine-  
tune the TV channel.  
The TV channel is deleted from the  
programme numbers list.  
If you cannot hear the normal sound  
even when the picture of the TV  
channel appears normally:  
The SYSTEM setting is wrong. Press the  
3button and choose a SYSTEM that has  
normal sound.  
MANUAL  
1 Press the 6buttons to choose a  
programme number to which you  
want to register a new TV channel.  
2 Press the blue button to activate the  
MANUAL function.  
6 Press the MENU/OK button and  
register the TV channel to a  
programme number.  
At the right side following the CH/CC  
number, the SYSTEM (sound system) of  
the TV channel appears.  
The normal EDIT menu is resumed.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the TV’s menu  
INSERT  
Preparation:  
• Find the CH/CC number  
corresponding to the channel number  
of the TV channel from page 33.  
1 Press the 6buttons to choose a  
programme number for which you will  
register a new TV channel.  
• When you attempt to insert the TV  
channel of NTSC-M system, press  
SOUND SYSTEM button to switch  
SOUND SYSTEM to M, then proceed  
to the next step.  
2 Press the green button to start the  
INSERT function.  
3 Press the 6buttons to choose “CC”  
or “CH” according to the CH/CC  
number of the TV channel.  
To cancel the INSERT function:  
Press the DISPLAY button.  
4 Press the Number buttons to enter the  
remaining CH/CC number.  
The TV shifts to registration mode. When  
the registration is completed, the picture  
of the TV channel appears on the  
screen.  
• The CH/CC number is a number  
indicating the broadcast frequency to  
the TV. If the TV cannot detect the TV  
channel corresponding to the  
broadcast frequency indicated by the  
CH/CC number, a picture in the no-  
signal state appears.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the TV’s menu  
CH/CC number  
When you want to use the INSERT function on page 32, find the CH/CC number  
corresponding to the Channel number of the TV channel from this table.  
US: The US channel numbers are the channel numbers used in the United States,  
Philippines, etc. CCIR: The CCIR channel numbers are the channel numbers used in the  
Middle East, Southeast Asia, etc. OIRT: The OIRT channel numbers are the channel  
numbers used in Eastern Europe, Russia, Vietnam, etc. AUSTRALIA: The AUSTRALIA  
channel numbers are the channel numbers used in Australia, etc.  
Channel  
Channel  
CH  
US  
CCIR  
E2  
OIRT  
AUSTRALIA  
AU-0  
CC  
US  
CCIR  
OIRT  
AUSTRALIA  
AU-5  
CH 02  
CH 03  
CH 04  
CH 05  
CH 06  
CH 07  
CH 08  
CH 09  
CH 10  
CH 11  
CH 12  
CH 13  
CH 14  
CH 15  
CH 16  
CH 17  
CH 18  
CH 19  
CH 20  
CH 21  
CH 22  
CH 23  
CH 24  
CH 25  
CH 26  
CH 27  
CH 28  
CH 29  
CH 30  
CH 31  
CH 32  
CH 33  
CH 34  
CH 35  
CH 36  
CH 37  
CH 38  
CH 39  
CH 40  
CH 41  
CH 42  
CH 43  
CH 44  
CH 45  
CH 46  
CH 47  
CH 48  
CH 49  
CH 50  
CH 51  
CH 52  
CH 53  
CH 54  
CH 55  
CH 56  
CH 57  
CH 58  
CH 59  
CH 60  
CH 61  
CH 62  
CH 63  
CH 64  
CH 65  
CH 66  
CH 67  
CH 68  
CH 69  
CH 70  
US-2  
R1  
CC 01  
CC 02  
CC 03  
CC 04  
CC 05  
CC 06  
CC 07  
CC 08  
CC 09  
CC 10  
CC 11  
CC 12  
CC 13  
CC 14  
CC 15  
CC 16  
CC 17  
CC 18  
CC 19  
CC 20  
CC 21  
CC 22  
CC 23  
CC 24  
CC 25  
CC 26  
CC 27  
CC 28  
CC 29  
CC 30  
CC 31  
CC 32  
CC 33  
CC 34  
CC 35  
CC 36  
CC 37  
CC 38  
CC 39  
CC 40  
CC 41  
CC 42  
CC 43  
CC 44  
CC 45  
CC 46  
CC 47  
CC 48  
CC 49  
CC 50  
CC 51  
CC 52  
CC 53  
CC 54  
CC 55  
CC 56  
CC 57  
CC 58  
CC 59  
CC 60  
CC 61  
CC 62  
CC 63  
CC 64  
CC 75  
CC 76  
CC 77  
CC 78  
CC 79  
CC 95  
CC 96  
CC 97  
CC 98  
CC 99  
S-1  
S-2  
US-3  
E3  
AU-1  
US-4  
E4  
R2  
R6  
R7  
R8  
R9  
AU-2  
S-3  
US-5  
E5  
AU-6  
S-4  
US-6  
E6  
AU-7  
S-5  
US-7  
E7  
AU-8  
S-6  
AU-5A  
US-8  
E8  
AU-9  
S-7  
US-9  
E9  
S-8  
US-10  
US-11  
US-12  
US-13  
US-14  
US-15  
US-16  
US-17  
US-18  
US-19  
US-20  
US-21  
US-22  
US-23  
US-24  
US-25  
US-26  
US-27  
US-28  
US-29  
US-30  
US-31  
US-32  
US-33  
US-34  
US-35  
US-36  
US-37  
US-38  
US-39  
US-40  
US-41  
US-42  
US-43  
US-44  
US-45  
US-46  
US-47  
US-48  
US-49  
US-50  
US-51  
US-52  
US-53  
US-54  
US-55  
US-56  
US-57  
US-58  
US-59  
US-60  
US-61  
US-62  
US-63  
US-64  
US-65  
US-66  
US-67  
US-68  
US-69  
E10  
E11  
E12  
R10  
R11  
R12  
AU-10  
AU-11  
S-9  
S-10  
S-11  
S-12  
S-13  
S-14  
S-15  
S-16  
S-17  
S-18  
S-19  
S-20  
S-21  
S-22  
S-23  
S-24  
S-25  
S-26  
S-27  
S-28  
S-29  
S-30  
S-31  
S-32  
S-33  
S-34  
S-35  
S-36  
S-37  
S-38  
S-39  
S-40  
S-41  
A
B
C
D
E
F
G
H
I
J
K
L
E21  
E22  
E23  
E24  
E25  
E26  
E27  
E28  
E29  
E30  
E31  
E32  
E33  
E34  
E35  
E36  
E37  
E38  
E39  
E40  
E41  
E42  
E43  
E44  
E45  
E46  
E47  
E48  
E49  
E50  
E51  
E52  
E53  
E54  
E55  
E56  
E57  
E58  
E59  
E60  
E61  
E62  
E63  
E64  
E65  
E66  
E67  
E68  
E69  
M
N
O
P
Q
R
S
T
U
V
W
W+1  
W+2  
W+3  
W+4  
W+5  
W+6  
W+7  
W+8  
W+9  
W+10  
W+11  
W+12  
W+13  
W+14  
W+15  
W+16  
W+17  
W+18  
W+19  
W+20  
W+21  
W+22  
W+23  
W+24  
W+25  
W+26  
W+27  
W+28  
X
Y
Z
Z+1  
Z+2  
R3  
R4  
R5  
AU-3  
AU-4  
A-5  
A-4  
A-3  
A-2  
A-1  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the TV’s menu  
3 Press the MENU/OK button to  
complete the setting.  
TELETEXT LANGUAGE  
[Except HV-29JH54/HV-29VH14/  
HV-29VH54]  
The menu disappears.  
• Languages that are not included in the  
teletext language group that you  
select, the sub-titles of the teletext  
program will not be displayed properly.  
There are five types of teletext language  
groups. Set the teletext language group that  
corresponds to the language of the teletext  
program that you want to watch.  
1 Choose TELETEXT LANGUAGE, then  
press the MENU/OK button.  
2 Press the 6buttons to choose a  
group.  
Group  
Languages  
Turkish, Hungarian, English,  
German, French, Italian,  
Spanish, Portuguese, Greek,  
Swedish, Finnish  
GROUP-1  
Polish, Serbian, Croatian,  
Slovenian, Czech, Slovak,  
GROUP-2 Rumanian, Hungarian, Ger-  
man, French, Italian, Swedish,  
Finnish  
Russian, Bulgarian, Lettish,  
Lithuanian, Estonian, Ukrain-  
an, Czech, Slovak, English,  
GROUP-3  
German, Rumanian  
Arabic, Czech, Slovak. Hun-  
garian, English, German,  
French, Italian, Spanish, Por-  
GROUP-4  
tuguese, Swedish, Finnish  
Farsi, Czech, Slovak. Hungar-  
ian, English, German, French,  
Italian, Spanish, Portuguese,  
GROUP-5  
Swedish, Finnish  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Additional preparation  
Connecting the external  
devices  
Connect the devices to the TV, paying  
attention to the following connection  
diagram.  
HV-29JH24  
HV-29JH54  
HV-29JH74  
HV-29VH14  
HV-29VH54  
Before connecting anything:  
• Read the manuals provided with the  
devices. Depending on the devices,  
the connection method may differ from  
the figure. In addition, the device  
settings may be changed depending  
on the connection method to secure  
proper operation.  
P
O
W
E
R
U  
ANL  
V
I
O
V
E
V
LNO  
R
ET  
(Behind the cover)  
• Turn off all the devices including the  
TV.  
IN (VIDEO-4)  
OVER  
OVER  
V
L/MONO  
R
S
V
L/MONO  
R
S
IN (VIDEO-4)  
• The “Specifications” on page 40  
contains the details of the VIDEO  
terminals. If you are connecting a  
device not listed in the following  
connection diagram, see the  
“Specifications” to choose the best  
VIDEO terminal.  
• Note that connecting cables are not  
supplied.  
1 VCR (composite signal)  
AUDIO  
R
L/MONOVIDEO  
S
O
V
E
R
VIDEO-1  
VIDEO-2  
2 VCR (S-VIDEO signal; Y/C)  
3 VCR for recording (composite signal)  
4 DVD player (composite signal)  
5 DVD player (S-VIDEO signal; Y/C)  
6 DVD player (component video signals;  
Y. PB/CB . PR/CR)  
B
VIDEO  
UDIO  
R A L/MONO  
VIDEO-3  
COMPONENT  
OUTPUT  
R
L
VIDEO  
AUDIO  
AUDIO  
L/MONO  
VIDEO  
S
R
OVER  
VIDEO-1  
VIDEO-2  
7 TV game (composite signal)  
8 TV game (S-VIDEO signal; Y/C)  
9 Camcorder (composite signal)  
0 Camcorder (S-VIDEO signal; Y/C)  
- Headphones  
P
R/CR  
P
B/CB  
Y/VIDEO  
VIDEO-3/  
COMPONENT  
R AUDLI/OMONO  
OUTPUT  
R
L
VIDEO  
AUDIO  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Additional preparation  
• In the VIDEO-4 terminal, the VIDEO  
jack is indicated by “V”.  
Connecting methods  
1 Connect the TV’s VIDEO jack and the  
device’s VIDEO OUT (video output)  
jack with a video cable.  
2 Connect the TV’s AUDIO jacks (L/  
MONO and R) and the device’s AUDIO  
OUT (audio L/R output) jacks with an  
audio cable.  
If connecting a device to the TV with an  
S-VIDEO cable:  
Connect the VCR’s S-VIDEO OUT (S-  
VIDEO output) connector and the TV’s S  
connector with an S-VIDEO cable, instead  
of connecting with a video cable.  
Note that the connection with a video cable  
will be ignored in case you connect a VCR  
to the TV with both video cable and S-  
VIDEO cable.  
If the device’s sound output is in mono:  
Connect the device’s AUDIO OUT jack and  
the TV’s L/MONO jack with an audio cable.  
Connecting devices to the  
OUTPUT terminal  
The signals of the images and sound you  
are currently viewing with this TV are output  
through the OUTPUT terminal. By  
connecting a VCR to the OUTPUT terminal,  
you can record the currently shown image  
and sound to that VCR. To do this, connect  
the VCR and OUTPUT terminal following  
the steps below.  
If connecting a DVD player to the TV with  
a component video cable.  
Connect three jacks (Y/VIDEO, CB and CR)  
in the VIDEO-3 terminal and the DVD  
player’s COMPONENT (component video  
output) jacks with a component video  
cables, instead of connection with a video  
cable. Then set the VIDEO-3 SETTING to  
COMPONENT, according to“VIDEO-3  
SETTING” on page 28.  
1 Connect the VIDEO jack in the  
OUTPUT terminal and the VCR’s  
VIDEO IN (video input) jack with a  
video cable.  
• This Television is compatible with the  
Progressive video signal (525P and  
625P signals) only when the  
2 Connect the AUDIO jacks (L and R) in  
the OUTPUT terminal and the VCR’s  
AUDIO IN (audio L/R input) jacks with  
an audio cable.  
component video signal is input.  
• When you turn off the TV, the signals  
from the OUTPUT terminal are also  
turned off.  
• The component signals input from the  
VIDEO-3/COMPONENT terminal  
cannot be output through the OUTPUT  
terminal.  
If you have a DVD player that outputs  
Progressive video signals (525P and  
625P signals) as a component video  
signal, then by attaching the device to  
the television with a component video  
cable you can see the actual images  
that are recorded on a DVD disc as an  
original image source.  
Connecting Headphones  
If connecting a device to the VIDEO-3/  
COMPONENT terminal with a video  
cable.  
Connect the TV’s Y/VIDEO jack and the  
device’s VIDEO OUT (video output) jack  
with a video cable.  
Connect the headphones with a stereo  
mini jack (of 3.5 mm in diameter) to the  
Headphone jack at the TV front panel.  
Then set the VIDEO-3 SETTING to VIDEO  
according to “VIDEO-3 SETTING” on  
page 28.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
If a problem arises while you are using the TV, please read this “Troubleshooting” well  
before you request having the TV repaired. You may be able to fix it easily by yourself. For  
example, if the AC plug is disconnected from the AC outlet, or the TV aerial has problems,  
you may think there is a problem with the TV itself.  
Important:  
• This Troubleshooting guide only covers problems whose causes are not easy to  
determine. If a question arise when you are operating a function, read the page(s)  
corresponding to the operation of the function well, not this Troubleshooting guide.  
• After you have followed the Troubleshooting description or the operating description of  
the functions concerned without any success, remove the AC plug from the AC outlet  
and request a repair of your TV. Do not attempt to repair the TV by yourself or remove  
the rear cover of the TV.  
• If the TV or aerial receives interference  
If you cannot turn on the TV  
from the other devices, stripes or noise  
may appear in the picture. Move such  
device as an amplifier, personal  
computer, or a hair drier that can  
cause interference away from your TV,  
or try changing its location. If the aerial  
suffers interference from a radio tower  
or high-voltage wire, please contact  
your local dealer.  
• If the TV receives interferences from  
signal reflecting from mountains or  
building, double-pictures (ghosting) will  
occur.  
Try to change the aerial’s direction or  
replace the antenna with the one with  
better directionality.  
• Are your COLOUR SYSTEM settings  
for the TV channels correct? Follow  
the description “COLOUR SYSTEM  
button” on page 11 to try to solve the  
trouble.  
• Is the AC plug connected to the AC  
outlet?  
• Is the POWER lamp lit? If not, press  
the Main power button.  
No picture/No sound  
• Have you chosen a TV channel whose  
reception is extremely bad? In this  
case, the BLUE BACK function will be  
activated, the entire screen becomes  
blue, and the sound is muted. In spite  
of this, if you want to view the TV  
channel, follow the description “BLUE  
BACK” on page 27 to try to change the  
BLUE BACK function setting to OFF.  
• Are your SOUND SYSTEM settings for  
the TV channels correct?  
Follow the description “SOUND  
SYSTEM button” on page 11 to try to  
solve the trouble.  
Poor picture  
• Has COLOUR or BRIGHT been  
controlled properly? Follow the  
description “Adjusting the picture” on  
page 20 to try to adjust them properly.  
• Videotaping teletext is not  
• If noise totally obscures the picture  
(snow), the aerial or aerial cable may  
have trouble. Check the following to try  
to solve the trouble:  
Has the TV and aerial been connected  
properly?  
Has the aerial cable been damaged?  
Is the aerial pointed to the right  
direction?  
recommended because it may not  
record correctly.  
Is the aerial itself faulty?  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
• When a white and bright still image  
(such as a white dress) is displayed on  
the screen, the white part may look as  
if it were coloured.  
It is a phenomenon unavoidable due to  
the nature of the picture tube itself, and  
not due to a TV failure.  
• When you are viewing a teletext  
programme, you cannot operate the  
menus.  
Press the TV/VIDEO button to return  
the teletext programme to the ordinary  
TV programme to try operating the  
menus.  
When the picture disappears from the  
screen, the unnatural colours will also  
disappear.  
• When viewing images from  
commercially available video software  
products, or videos from videotapes  
which have been recorded improperly,  
the top of the image may be distorted.  
This is due to the condition of the video  
signal, and not because of  
• Is the CHILD LOCK function set to  
ON? If the CHILD LOCK function is set  
to ON, you cannot operate the TV with  
the front control buttons of the TV.  
Follow the description “CHILD LOCK”  
on page 27 to try to set the CHILD  
LOCK function to OFF.  
• If the TV operation becomes disabled  
suddenly, press the Main power button  
on the TV and turn off the main power.  
Try to press the Main power button  
again to turn on the main power. If the  
TV returns to a normal state, it is not a  
failure.  
• The following functions do not operate  
when receiving Progressive video  
signal (525P and 625P signals).  
Remote control function:  
PIP, MULTI, FREEZE and STROBE  
button.  
malfunction.  
Poor sound  
• Have you adjusted BASS or TREBLE  
properly? If not, follow the description  
“Adjusting the sound” on page 25 to try  
to adjust them properly.  
• When the TV channel reception is  
poor, it can be hard to hear the stereo  
or bilingual sound. In this case, follow  
the description “STEREO / I•II” on  
page 25 to hear the sound more easily  
by changing it to a mono sound.  
MENU function:  
TINT and PULL DOWN  
Other concerns  
Operation disabled  
• When the AUTO SHUTOFF function  
operates, the TV is automatically  
turned off.  
• Have the batteries of the remote  
control become exhausted?  
Follow the description “Putting the  
batteries into the remote control” on  
page 4 and replace them with new  
batteries to try solve the problem.  
• Have you attempted to use the remote  
control at the sides or rear of the TV or  
at a location more than seven meters  
apart from the TV location? Operate  
the remote control in the front of your  
TV or a location less than seven  
meters from your TV to try to solve the  
problem.  
If the TV is turned off suddenly, try to  
press the POWER button to turn on  
the TV once again. At this time, if the  
TV resumes a normal state, there is no  
problem.  
• If you bring a magnetized device such  
as a speaker near to your TV, a picture  
may be warped or unnatural colours  
appear at the corners of the screen. In  
this case, keep the device apart from  
your TV. If the speaker causes such  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
phenomena, use the magnetic-  
shielded speaker instead.  
• A picture may be tilted due to the  
influence of the earth’s magnetism. In  
this case, use the “PICTURE TILT” on  
page 23 to complete the tilt.  
• It takes a short period of time from the  
time an operation such as changing  
channels is performed until an image is  
displayed. This is not a malfunction.  
This is the time required for the image  
to stabilize before it can be displayed.  
• The TV may emit a crackling sound  
due to a sudden change in  
temperature. It does not matter if a  
picture or sound does not show any  
abnormality. If you hear crackling  
sounds frequently while you are  
viewing the TV, other causes may be  
assumed.  
For precautionary purposes, request  
your service technician to inspect it.  
• Touching the screen may cause you  
feel a slight electric shock due to its  
static electricity.  
It is an unavoidable phenomenon due  
to the construction of the picture tube.  
It is not a problem with the TV.  
You can rest assured that this static  
discharge does not have harmful  
influence over the human body.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
Broadcasting systems  
Colour systems  
B, G, I, D, K, K1, M  
PAL, SECAM, NTSC3.58/4.43MHz  
Channels and frequencies  
VHF low channel (VL) =46.25 to 168.25 MHz  
VHF high channel (VH) =175.25 to 463.25 MHz  
UHF channel (U)  
=471.25 to 863.25 MHz  
• Receives cable channels in mid band (X to Z+2, S1 to S10), super band (S11  
to S20) and hyper band (S21 to S41).  
Sound-multiplex systems  
Teletext systems  
A2 (B/G), NICAM (B/G, I, D/K) system  
FLOF(Fastext), WST(World Standard Text)  
[Except HV-29JH54/HV-29VH54/HV-29VH14]  
Languages displayed by  
teletext  
Please see the table in the description “TELETEXT LANGUAGE” on page 34.  
[Except HV-29JH54/HV-29VH54/HV-29VH14]  
Power requirements  
Audio output  
AC 110 to 240V, 50/60Hz  
Rated Power output: 10W + 10W  
VIDEO-1 terminal  
RCA connector × 3, S-VIDEO connector × 1  
• Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.  
VIDEO-2 terminal  
RCA connector × 3  
• Video input and Audio L/R inputs are available.  
VIDEO-3/COMPONENT  
RCA connector × 5 terminal  
• Video input/Component video (Y. PB/CB . PR/CR) input and Audio L/R inputs  
are available.  
• Progressive video signal (525P and 625P signals) input is available.  
VIDEO-4 terminal  
OUTPUT terminal  
RCA connector × 3, S-VIDEO connector × 1  
• Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.  
RCA connector × 3  
• Video output and Audio L/R outputs are available.  
Headphone jack  
Accessories  
Stereo mini-jack (3.5 mm in diameter)  
Remote control unit × 1  
RM-C1350 [HV-29JH74]  
RM-C1351 [HV-29JH24]  
RM-C1352 [HV-29VH14]  
RM-C1353 [HV-29JH54/HV-29VH54]  
AA/R6 dry cell battery × 2  
Speakers  
(13cm × 6.5cm) × 2  
Design and specifications subject to change without notice.  
Pictures displayed on the screen using this TV’s ZOOM functions should not be shown for any commercial or  
demonstration purpose in public places (cafes, hotels, etc.) without the consent of the owners of copyright of  
the original picture sources, as this constitutes an infringement of copyright.  
0704-CR-JMT  
c
2004 Victor Company of Japan, Limited  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Ingersoll Rand Water Pump PD03P XXX XXX User Manual
Intel Saw srcsas144e User Manual
JVC CD Player KD DV5400 User Manual
JVC Personal Computer LYT1361 001A User Manual
JVC Portable CD Player RC EX25S User Manual
JVC Stereo System 0505NYMCREBET User Manual
Kenmore Cooktop 7904380 User Manual
Kenwood Car Speaker KFC HQ691 User Manual
Keys Fitness Treadmill 980HRS User Manual
Kramer Electronics Switch 6241 User Manual