®
Stealthbox
I N S TALLATI O N GUI DE
START
HERE
for the
2
➔
➔
SB-GM-CLREXT/10W3v2
(2004-Up Chevrolet Colorado &
GMC Canyon Extended Cab)
3
➔
➔
➔
➔
➔
1
➔
STEP 1: Remove all contents from rear of
truck.
STEP 2: Remove the plastic jack cover and
jack from the bracket.
STEP 3: Remove the (1) tire stops and with
a 10mm socket, (2&3)unbolt the jack bracket.
This Stealthbox is a product which
requires professional installation skills and
tools.
Please read this installation guide thor-
oughly before beginning the project. It
will guide you step by step through the
installation. Several of the steps in this
process may require two people to
accomplish.
➔
It is absolutely vital that the enclosure
be properly mounted to the vehicle
according to these instructions. Failure
to mount the enclosure properly pres-
ents two problems: 1) The sub-bass
performance will suffer due to the
movement of the enclosure caused by
the force exerted by the woofer(s) and
2) A loose enclosure presents a serious
safety hazard in the event of a collision
or sudden deceleration.
STEP 4: Unbolt the bracket that is already
attached to the Stealthbox.
STEP 5: With the supplied hardware, attach
the bracket to the rear wall.
STEP 6: Attach speaker wire to the
Stealthbox terminal and check the woofer for
proper operation.
Set mounting hardware to the side.This will
be used in later steps.
Place a 1/4” lock wash and a 1/4” flat washer
onto each #6x30mm-1mm bolt.
Place the bolts through the bracket and slide
one 1”Lx1”ODx3/8”ID spacer onto each bolt.
Line up the bolts to the factory threads and
secure tightly.
Please enjoy your JL Audio Stealthbox
responsibly.
Continued on Next Page ➔
SB-GM-CLREXT/10W3v2, JL AUDIO, Inc 2005
Page 1
Sheet SKU#011195 Revision 5/19/2005
Download from Www.Somanuals.com. All Manuals Search And Download.
Cont.
From
Previous
Page
CO NGRATULATIO NS!
INSTALL CO MPLETE.
➔
➔
➔
➔
Included Hardware:
4) 1/4” Flat W asher
4) 1/4” Split Lock W asher
2) 1/4”-20 x 1” Bolts
2) #6 x 30m m -1m m Hex Bolts
1) 3/8” Split Lock W asher
2) 3/8” Flat W asher
STEP 13: Place a supplied 3/4”Lx3/4”ODx3/8”ID
spacer onto the thumb screw.
STEP 14: On the back side of the plastic jack
cover.
STEP 15: Place the tire stops and jack back onto
the jack bracket.
1) 3/8” Fender W asher
1) 3/8”-16 x 2” Tap Bolt
1) 3/8”-16 Hex Nut
Insert the thumb screw through the front of the
plastic jack cover.
Place the remaining pair of 3/4”Lx3/4”OD,3/8”ID
spacers onto the thumb screw.
Place the plastic jack cover over the jack assembly
and secure with the thumb screw.
3) 3/4”Lx3/4”O Dx3/8”ID Spacers
2) 1”L x1”O D x3/8”ID Spacers
Difficulty O f Installation:
Mid/High Frequency Driver Information:
Specifications:
Enclosure Type: Sealed
Front Location Driver Size:
6.5”
Driver Type: 10W3v2-D2
Nominal Impedance: 4Ω
Cont. Power Handling: 300 Watts
XR650-CSi
Applicable JL Audio Products:
TR,VR,XR & ZR650-CSi
JL Audio recommends using a high quality amplifier such as the JL Audio 250/1. The diagram below shows the recommended
crossover, infrasonic filter and equalizer settings for the 250/1 when being used to power your Stealthbox®.
Rear Location Driver Size:
6.5”
+12VDC
Ground Remote
Preamp Output Section
Output Mode
Bass Control
Infrasonic Filter
Amp LP Filter
Mode/Slope
Amplifier Input Section
Input Voltage
Input Sens. Signal Sensing
Applicable JL Audio Products:
TR,VT & XR650-CXi
Full-Range/Low-Pass/High-Pass
Off/30Hz
+7
Off/12dB/24dB
Low/High
Off/On
+3
+1
+10
+13
JL AUDIO 250/1
monoblock subwoofer amplifier
Left Ch.
Right Ch.
LF Boost (dB) Filter Freq. (Hz)
Left Ch.
Right Ch.
TR650-CXi
The JL Audio 250/1 is a very versatile audio component. Please consult the owner’s manual for detailed information
about installing and tuning this amplifier.
10369 N. Commerce Pkwy, Miramar, Florida 33025-392
Phone: 954.443.1100
Fax: 954.443.1111
SB-GM-CLREXT/10W3v2, JL AUDIO, Inc 2005
Page 3
Sheet SKU#011195 Revision 5/19/2005
Download from Www.Somanuals.com. All Manuals Search And Download.
|