Owner’s Operator and Maintenance Manual
Portable Patient Lift and
Sling
DEALER: This manual MUST be given to
the user of the patient lift.
USER: BEFORE using this patient lift, read
this manual and save for future reference.
For more information regarding
Invacare products, parts, and services,
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
TABLE OF CONTENTS
Assembling the Lift...................................................................................................................................10
Operating the Lift.....................................................................................................................................10
Using the Sling...........................................................................................................................................11
Transferring the Patient..........................................................................................................................12
Performing Maintenance.........................................................................................................................12
Patient Slings..............................................................................................................................................13
Model Nos. 9042, 9043, 9046 and 9047 Slings.............................................................................14
Base, Mast and Boom Assembly.......................................................................................................16
Body........................................................................................................................................................19
Attaching the Sling Hardware................................................................................................................23
3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
TABLE OF CONTENTS
Operating the Patient Lift.......................................................................................................................26
Transferring Patient for Use of Commode Chair or Standard Commode ................................32
Transferring to a Wheelchair................................................................................................................35
Maintenance Safety Inspection Checklist............................................................................................43
REGISTER YOUR PRODUCT
The benefits of registering:
1. Safeguard your investment.
2. Ensure long term maintenance and servicing of your purchase.
3. Receive updates with product information, maintenance tips, and industry news.
4. Invacare can contact you or your provider, if servicing is needed on your product.
5. It will enable Invacare to improve product designs based on your input and needs.
- or -
Complete and mail the form on the next page
Any registration information you submit will be used by Invacare Corporation only, and
protected as required by applicable laws and regulations.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT REGISTRATION FORM
Complete and mail this form
Name_______________________________________________________________
Address _____________________________________________________________
City ___________________State/Province __________
Zip/Postal Code ________
Fold
here
Email ___________________________________Phone No. _________________
Invacare Model No. ______________________Serial No. __________________
Purchased From _________________________Date of Purchase:___________
1. Method of purchase: (check all that apply)
❏ Medicare
2. This product was purchased for use by: (check one)
❏ Self ❏ Parent ❏ Spouse ❏ Other
3. Product was purchased for use at:
❏ Home ❏ Facility ❏ Other
4. I purchased an Invacare product because:
❏ Price ❏ Features (list features) _________________________________________
❏ Insurance
❏ Medicaid ❏ Other
__________________________
5. Who referred you to Invacare products? (check all that apply)
❏ Doctor ❏ Therapist ❏ Friend ❏ Relative ❏ Dealer/Provider ❏ Other_________
❏ Advertisement (circle one): TV, Radio, Magazine, Newspaper
❏ No Referral_____
6. What additional features, if any, would you like to see on this product?
__________________________________________________________________________
Fold
here
7. Would you like information sent to you about Invacare products that may be available for a
particular medical condition? ❏ Yes ❏ No
If yes, please list any condition(s) here and we will send you information by email and/or mail about
any available Invacare products that may help treat, care for or manage such condition(s):
__________________________________________________________________________
8. Would you like to receive updated information via email or regular mail about the Invacare
home medical products sold by Invacare's dealers? ❏ Yes ❏ No
9. What would you like to see on the Invacare website?
__________________________________________________________________________
10. Would you like to be part of future online surveys for Invacare products? ❏ Yes ❏ No
11. User's Year of birth: ______________________________________________________
If at any time you wish not to receive future mailings from us, please contact us at Invacare Corporation,
CRM Department, 39400 Taylor Parkway, Elyria, OH 44035, or fax to 877-619-7996 and we will remove
you from our mailing list.
Download from Www.Somanuals.com. All Manuals Search And Download.
LABEL LOCATION
LABEL LOCATION
Models 9805 and 9805P
WARNING
WEIGHT CAPACITY is 450 lbs.
The INVACARE Patient Lift
is NOT a transport device.
Moving a person suspended
in a sling over ANY distance
is NOT R ECO M M EN DE D.
DO NOT roll casterbase over
deep carpet, raised carpet
bindings, door frames or any
uneven surfaces that may
cause the Patient Lift to tip
over.
DO NOT lock the casters of
the Patient Lift when lifting
an individual. Casters MUST
be left unlocked to allow
P a t i e n t L i f t t o s t a b i l i z e
during lifting procedures.
U S E O N L Y g e n u i n e
INVACARE SLINGS and LIFT
ACCESSORIES.
Refer to Owner's Manual for
periodic Maintenance
Procedures.
NOTICE
Upon receipt of the patient lift, the end
user shoud request an updated version
of the owner's manual for proper operation
and safety procedures.
Customer Service:
1-800-333-6900
1059597
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL NOTES
SPECIAL NOTES
Signal words are used in this manual and apply to hazards or unsafe practices which
could result in personal injury or property damage. Refer to the following table for
definitions of the signal words.
SIGNAL WORD
MEANING
DANGER
Danger indicates an imminently hazardous situation which, if not avoided, will result in
death or serious injury.
WARNING
CAUTION
Warning indicates a potentially hazardous situation which, if not avoided, could result in
death or serious injury.
Caution indicates a potentially hazardous situation which, if not avoided, may result in
property damage.
NOTICE
THE INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJECT TO
CHANGE WITHOUT NOTICE.
MAINTENANCE
Maintenance MUST be performed only by qualified personnel.
NOTES highlight procedures and contain information which assist the operator in
understanding the information contained in this manual.
ꢀ WARNING
Invacare products are specifically designed and manufactured for use in conjunction
with Invacare accessories. Accessories designed by other manufacturers have not
been tested by Invacare and are not recommended for use with Invacare products.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
TYPICAL PRODUCT PARAMETERS
TYPICAL PRODUCT PARAMETERS
9805 Hydraulic Adjustable Lift
9805P Hydraulic Adjustable Lift - Painted
BASE (ONLY):
MAST (ONLY):
9884
9884P
N/A
9800A
BASE WIDTH
OPEN:
CLOSED:
42¼-inches
22-inches
42¼-inches
22-inches
BASE HEIGHT:
BASE LENGTH:
6½-inches
6½-inches
46¾-inches
46¾-inches
BOOM HEIGHT AT
SLING ATTACHMENT:
MIN.:
MAX.:
RANGE:
17-inches
61-inches
44-inches
17-inches
61-inches
44-inches
BOOM OVERALL
HEIGHT:
73-inches
450 lbs
73-inches
450 lbs
WEIGHT CAPACITY:
*CASTER SIZE:
5-inches
5-inches
SHIPPING WEIGHT:
(UNIT IN CARTON)
85 lbs
85 lbs
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1—GENERAL GUIDELINES
SECTION 1—GENERAL GUIDELINES
ꢀ WARNING
SECTION 1 - GENERAL GUIDELINES contains important information for the safe
operation and use of this product. DO NOT use this product or any available
optional equipment without first completely reading and understanding these
instructions and any additional instructional material such as Owner’s Manuals,
Service Manuals or Instruction Sheets supplied with this product or optional
equipment. If you are unable to understand the Warnings, Cautions or Instructions,
contact a healthcare professional, dealer or technical personnel before attempting
to use this equipment - otherwise, injury or damage may occur.
Check all parts for shipping damage before using. In case of damage, DO NOT use the
equipment. Contact the Dealer for further instructions.
The Invacare patient lift is not a transport device. It is intended to transfer an individual
from one resting surface to another (such as a bed to a wheelchair). Moving a person
suspended in a sling over any distance is not recommended.
DO NOT attempt any transfer without approval of the patient’s physician, nurse or
medical assistant. Thoroughly read the instructions in this Owner’s Manual, observe a
trained team of experts perform the lifting procedures and then perform the entire lift
procedure several times with proper supervision and a capable individual acting as a
patient.
Use common sense while operating lifts. Special care MUST be taken with people with
disabilities who cannot cooperate while being lifted.
Invacare slings and patient lift accessories are specifically designed to be used in
conjunction with Invacare patient lifts. Slings and accessories designed by other
manufacturers are not to be utilized as a component of Invacare’s patient lift system.
Assembling the Lift
DO NOT overtighten mounting hardware. This will damage mounting brackets.
Operating the Lift
Although Invacare recommends that two assistants be used for all lifting preparation,
transferring from and transferring to procedures, our equipment will permit proper
operation by one assistant. The use of one assistant is based on the evaluation of the
healthcare professional for each individual case.
DO NOT exceed maximum weight limitation of the patient lift. The weight limitation for
the 9805 and the 9805P lifts is 450 lbs.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1—GENERAL GUIDELINES
If the patient lift is exposed to extreme temperature (above 100°F or below 32°F), high
humidity and/or becomes wet, prior to use, ensure handgrips do not twist on patient lift
handle - otherwise damage or injury may occur.
Using the Sling
Use an Invacare approved sling that is recommended by the individual’s doctor, nurse or
medical assistant for the comfort and safety of the individual being lifted.
DO NOT use any kind of plastic back incontinence pad or seating cushion between
patient and sling material that may cause the patient to slide out of the sling during
transfer.
After each laundering (in accordance with instructions on the sling), inspect sling(s) for
wear, tears, and loose stitching.
Bleached, torn, cut, frayed, or broken slings are unsafe and could result in injury. Discard
IMMEDIATELY.
DO NOT alter slings.
Be sure to check the sling attachments each time the sling is removed and replaced to
ensure that it is properly attached before the patient is removed from a stationary object
(bed, chair or commode).
If the patient is in a wheelchair, secure the wheel locks in place to prevent the chair from
moving forwards or backwards.
When connecting slings equipped with color coded straps to the patient lift, the shortest
of the straps MUST be at the back of patient for support. Using longer straps will leave
little or no support for patientʹs back. The loops of the sling are color coded and can be
used to place patient in various positions. The colors make it easy to connect both sides of
the sling equally. Make sure that there is sufficient head support when lifting a patient.
Lifting the Patient
When using an adjustable base lift, the legs MUST be in the maximum Opened/Locked
position before lifting the patient.
When the sling is elevated a few inches off the surface of the bed and before moving the
patient, check again to make sure that the sling is properly connected to the hooks of the
swivel bar. If any attachments are not properly in place, lower the patient back onto the
stationary surface and correct this problem - otherwise, injury or damage may occur.
Adjustments for safety and comfort should be made before moving the patient. Patientʹs
arms should be inside of the straps.
Invacare slings are made specifically for use with Invacare Patient Lifts. For the safety of
the patient, DO NOT intermix slings and patient lifts of different manufacturers.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1—GENERAL GUIDELINES
Before transferring a patient from a stationary object (wheelchair, commode or bed),
slightly raise the patient off the stationary object and check that all sling attachments are
secure. If any attachment is not correct, lower the patient and correct the problem, then
raise the patient and check again.
During transfer, with patient suspended in a sling attached to the lift, DO NOT roll caster
base over objects such as carpet, raised carpet bindings, door frames, or any uneven
surfaces or obstacles that would create an imbalance of the patient lift and could cause the
patient lift to tip over. Use steering handle on the mast at all times to push or pull the
patient lift.
Transferring the Patient
When elevated a few inches off the surface of the stationary object (wheelchair, commode,
or bed) and before moving the patient, check again to make sure that the sling is properly
connected to the hooks of the swivel bar. If any attachments are not properly in place,
lower the patient back onto the commode chair or the standard commode and correct this
problem.
Wheelchair wheel locks MUST be in a locked position before lowering the patient into the
wheelchair for transport.
Before transferring, check that the wheelchair weight capacity can withstand the patientʹs
weight.
Be sure to check the sling attachments each time the sling is removed and replaced, to
ensure that it is properly attached before the patient is removed from the bed or chair.
Mast pivot under the rubber boot must be tight to ensure safe use of the patient lift. Bolt
MUST be checked at least every six months in conjunction with periodic maintenance.
Performing Maintenance
The pump is sealed at the factory. DO NOT attempt to open the pump or obtain local
service as this will void the warranty and might result in damage. Consult your dealer or
write Invacare for further information.
After the first year of use, the hooks of the swivel bar and the mounting brackets of the
boom should be inspected every three months to determine the extent of wear. If these
parts become worn, replace them IMMEDIATELY.
Casters and axle bolts require inspections every six months to check for tightness and
wear.
After the first twelve months of operation, inspect the swivel bar and the eye of the boom
(to which it attaches) for wear. If the metal is worn, the parts MUST be replaced. Make this
inspection every six months thereafter.
Regular maintenance of patient lifts and accessories is necessary to assure proper
operation.
DO NOT overtighten mounting hardware. This will damage mounting brackets.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2—FEATURES
SECTION 2—FEATURES
Hydraulic Lifts
NOTE: For this procedure, refer to FIGURE 2.1.
Hydraulic pump suggested operating limit is 450 lbs.
Masts are interchangeable with bases. Lock together. Masts can be separated for storage.
Operation optimizes lift capabilities. The lift requires less physical effort for raising
patient.
Offset mast and boom style provides better
lift path. It maximizes full travel range.
D
C
Pump handle can rotate from side-to-side
for convenience of assistant.
A. The Castered Base
B. The Shifter Handle
C. The Mast
H
G
B
E
F
D. The Boom
E. Swivel Bar
F. Hydraulic Pump
G. Pump Handle
H. Control Valve
A
Patient Slings
ꢀ WARNING
Use a sling that is recommended by the individual’s doctor, nurse or medical assis-
tant for the comfort and safety of the individual being lifted.
Patient slings work in conjunction with lifts to support the patient during lifting and
transferring procedures.
Slings attach to the lift by using either sewn-in loop straps, chains or adjustable straps.
Slings are adjustable. They are interchangeable with any Invacare patient lift.
Each sling offers reinforcing at each hook-on point to ensure patient safety.
Each sling is constructed of durable materials which resist deterioration from exposure to
moisture or laundering.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2—FEATURES
Invacare products are specifically designed and manufactured for use in conjunction with
Invacare accessories. Accessories designed by other manufacturers have not been tested
by Invacare and are not recommended for use with Invacare products.
Model Nos. 9042, 9043, 9046 and 9047 Slings
The one-piece contour sling can be used on heavy or light patients. Slings support the
patient from shoulders to the knees. Slings are used for weighing, transferring or to
simplify the use of bathroom facilities.
DETAIL “A”
9043 & 9047
SLING WITH
COMMODE
OPENING
DETAIL “B”
9042 & 9046
SLING WITHOUT
COMMODE
OPENING
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 3—HANDLING
SECTION 3—HANDLING
Shipping and Transportation Instructions
NOTE: For this procedure, refer to FIGURE 3.1.
NOTE: If the patient lift is to be reshipped by common carrier, it should be packed in the same
carton. Extra cartons are available from Invacare.
Unpacking
1. Check for any obvious damage to the carton or its contents. If damage is evident,
notify Carrier/Invacare Dealer.
2. Remove all loose packing from the carton.
3. Carefully remove all the components from the carton.
NOTE: Unless the patient lift is to be used immediately, retain boxes, containers and packing
material for use in storing until use of the patient lift is required.
Inspection
1. Examine exterior of the patient lift for nicks, dents, scratches or damages. Inspect all
components.
Storage
1. Store the repackaged patient lift in a dry area.
2. DO NOT place other objects on top of the repackaged patient lift.
Apply stretch wrap 5 to 6
times around the mast
Apply stretch wrap 5 to 6
times around the mast
DETAIL “A”
Mast with pump
(Ref.)
Screw Lift
(Ref.)
Swivel Bar
(Ref.)
See
Detail “A”
Angle Swivel Bar
(Ref.)
Tape (Ref.)
Tape (Ref.)
Tape Hex Key Here
Tape (Ref.)
Tape Hex
Key Here
Tape (Ref.)
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4—ASSEMBLY
SECTION 4—ASSEMBLY
Assembly of the Patient Lift
ꢀ WARNING
Use only Invacare parts in the assembly of this lift. The base legs, the mast, boom,
pump assembly and the swivel bar are manufactured to specifications that assure
correct alignment of all parts for safe functional operation.
CAUTION
DO NOT run the lift until it is fully assembled.
Follow the assembly instrudctions in the Owner’s Manual for proper assembly of
this lift. Failure to do so could result in damage to the push handle of the lift, render-
ing it inoperative.
Base, Mast and Boom Assembly
1. Unpack the components from the
shipping cartons.
2. Remove the locking screw from the
bottom of the base.
NOTE: The bottom of the mast assembly will
have a notch.
Locking Screw
Bolt and Locknut
3. Match the notch at the bottom of the
Bottom of mast notch
mast assembly with the tabs inside the
socket of the base assembly.
4. Insert the mast assembly into the socket
and onto the tabs.
5. Turn the mast assembly to make sure
that the notch is locked on the tabs of
the socket.
Top Inside of the
Socket of the
Base Assembly
NOTE: If the mast does not turn, the mast is
centered and locked in place.
6. Insert the locking screw into the bottom
of the base and securely tighten.
ꢀ WARNING
The mast may be removed from the
base for storage or transporting. Each
time the mast is removed and returned
to the socket of the base, the mast
MUST be locked into the socket of the
base assembly.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4—ASSEMBLY
7. Remove the bolt and locknut from the top of the mounting bracket of the mast
assembly.
8. Align the holes of the boom assembly and mast assembly mounting bracket. Insert the
bolt completely through the holes of the mast assembly mounting bracket and the
boom assembly.
NOTE: Be sure that the bolt is completely through the holes of the mast assembly mounting bracket
and boom assembly, and they are not riding on the shoulder of the bolt.
CAUTION
The boom and mast, when assembled, MUST pivot easily.
9. Tighten the bolt and nut using the Allen wrench provided and an adjustable wrench.
NOTE: The nut and bolt can be tightened completely and the boom assembly will pivot easily if the
mounting hardware is aligned properly when the boom assembly is secured to the mast. To check
for correct alignment of the hardware, use the Allen wrench provided and turn the bolt by hand (it
should rotate without a lot of force being applied). If excessive force is necessary, the bolt is NOT
aligned properly. Disassemble and repeat assembly procedures until proper alignment is obtained.
10. To check for tightness of nut and bolt:
A. Raise the boom assembly.
B. Push the control handle away from the pump assembly.
C. If the boom assembly pivots easily, then the nut and bolt are not too tight.
D. If the boom assembly does not pivot easily or does not pivot at all, then the nut and
bolt are not aligned properly.
Locknut
Mast Assembly Mounting Bracket
Boom Assembly
Bolt
NOTE: Mast assembly mounting
bracket, boom assembly, bolt and
locknut MUST all be flush against
each other
17
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4—ASSEMBLY
Base Shifter Handle Assembly
NOTE: For this procedure, refer to
Base Shifter Handle
1. Insert the base shifter handle into the
cam lock assembly at the back of the
base.
Thumbscrew
Cam Lock
Assembly
2. Align the holes of the shifter handle
and cam lock assembly.
3. Tighten the thumbscrew to secure the
shifter handle in place.
NOTE: This should prevent the base shifter
handle from being removed.
Swivel Bar Attachment with Mounting Bracket
NOTE: For this procedure, refer to FIGURE 4.4.
1. Push the pin and washers up through the swivel bar pad.
2. Line-up hole in pin with mounting bracket holes and secure with shoulder screw and
nut provided.
NOTE: The swivel bar has hooks on both ends to accept the hardware used to attach the sling that
supports the patient during lift. The swivel bar pad should remain in place during normal use.
NOTE:Makesure PinandWashersarecompletely
pushed up through the Swivel Bar Pad.
Nut
Shoulder
Screw
Pin
Swivel Bar Pad
18
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5—ONE-PIECE CONTOUR SLINGS
SECTION 5—ONE-PIECE CONTOUR
SLINGS
Slings Using Chains, O-rings and D-rings
ꢀ WARNING
Invacare slings are designed specifically for use with Invacare Patient Lifts and made
to support the patient during lift and transfer procedures. Slings attach to the lift
with either straps or chains (interchangeable). The slings are reinforced at all points
of attachment for safety. The fabrics used in these slings are of very durable materi-
als that resist deterioration from exposure to moisture and laundering. This design
will accommodate patients of heavy or light weight with support from the shoulders
to the knees. The contour shape provides comfort during the lift by avoiding the
bulk of excess material between the back and seat sections.
Fabric
The fabric has a smooth inner side. The outer side has binding tape around the pocket.
NOTE: Always place the sling under the patient with the smooth side next to the body.
Sling fabrics are offered in a choice of two materials. Canvas fabric is very durable for use
and laundering and is preshrunk and dyed a BLUE color.
NOTE: Laundering should always be done with dark colors.
Open mesh nylon fabric is an exceptional material that provides safety and comfort for
the patient. The open mesh weave of the fabric is dyed BLUE, preshrunk, and durable for
use and laundering. It provides considerable traction to resist slipping and sliding during
use.
Body
Slings may be ordered at the time of purchase with a commode opening in the seat section
for use over a commode or a commode chair.
Each sling includes four metal support bars that have a hole at the center to attach the
S-hook.
When shipped from the factory, these reinforcing metal support bars are enclosed in the
sling pocket with the hole exposed.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5—ONE-PIECE CONTOUR SLINGS
Positioning the Contour Sling
1. Position the patient in the center of the bed and laying flat on his/her back.
2. Fold the sling in half (length-wise) and place the fabric sections of the sling beside the
patient.
NOTE: The sling french seams (uneven surface) will be against the bed surface and facing the
assistant when folded. The opposite side of the fabric is smooth. After the sling is positioned for
lifting purposes, the smooth side will be next to the patient.
NOTE: The top edge of the sling fabric (nearest to the patient’s head) should be slightly above the
armpit level of the patient.
NOTE: The bottom edge of the sling fabric should then be a few inches above the back of the
patient’s knee.
3. With both assistants holding the patient, push the folded sling under the patient
without rolling him/her over.
DETAIL “A” - POSITIONING
DETAIL “B” - PREPPING PATIENT
Center of Bed
Top Edge
of Sling
French Seams
(Facing the
assistant and Bed
Surface)
BottomEdge
of Sling
DETAIL “C” - ROLLING
PATIENT TO SIDE
DETAIL “D” - ROLLING PATIENT BACK
20
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5—ONE-PIECE CONTOUR SLINGS
Positioning the Patient on the Sling
NOTE: Use the following method to easily move the patient and avoid strain to yourself.
1. If the patient is to roll to their left-side, then elevate the patient’s right knee until the
right foot is flat on the bed (Detail “B” of FIGURE 5.1).
NOTE: Invacare recommends that two assistants (one on each side of the bed) be used when
positioning the patient in a sling.
2. With an assistant on each side of the bed and up against the mattress, the
assistantassistant on the left-hand side of the bed will position his/her right-hand on
the elevated knee and his/her left-hand under the patient’s right shoulder, slowly push
on the knee and assist with a slight lift of the shoulder and the patient will easily roll
3. With the patient on their side, push the fabrics of the seat and back gently under them.
NOTE: The upper edge of the back section should be positioned slightly above the armpit level and
the lower edge of the seat section positioned a few inches above the back of the patient’s knees (Detail
NOTE: assistants will reverse roles.
5. After the patient has been positioned once again on his/her back, you now need to roll
the patient to their right-side (facing the assistant on the left).
6. With an assistant on each side of the bed and up against the mattress, the assistant on
the right-hand side of the bed will elevate the left knee and position his/her left-hand
on the elevated knee and his/her right-hand under the patient’s left shoulder. The
assistant will slowly push on the knee and assist with a slight lift of the shoulder and
the patient will easily roll onto their side (Detail “B” of FIGURE 5.2).
7. Pull the fabrics of the seat and back across the mattress until they are smooth.
8. Roll the patient onto their back and they should be approximately centered on the
sling (Detail “C” of FIGURE 5.2).
9. You are now ready to attach the chains or straps to the sling.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5—ONE-PIECE CONTOUR SLINGS
DETAIL “A” - POSITIONING
DETAIL “B” - ROLLING PATIENT TO SIDE
Patient
Centered
in Sling
DETAIL “C” - ROLLING PATIENT BACK
22
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 6—ATTACHING SLING HARDWARE
SECTION 6—ATTACHING SLING
HARDWARE
Attaching the Sling Hardware
The hardware used with the one-piece contour sling includes four metal support bars.
The hardware inserts into the pockets at the edge of the fabric. The pocket that will hold
the metal bar has an opening in the center. The pocket is sewn closed on one end and has
an open-end with a strap on the other.
NOTE: When the slings are laundered, remove the four metal support bars. They MUST be
replaced or the sling can not be used for lifting purposes.
Inserting the Four Metal Support Bars into the Sling
NOTE: For this procedure, refer to FIGURE 6.1 on page 24.
NOTE: When inserting each metal bar into the sling pocket, align the metal support bar in the
center of the strap (after it has been pulled down) and push the metal support bar into the sling
pocket. The sling is sewn on both sides so the center location is critical.
1. To insert the metal support bar, pull the strap down allowing the bar to pass through
the opening in the sling pocket.
2. Push the metal support bar through until the mounting hole clears the center opening
of the sling pocket.
3. Once the opposite end of the bar is inside the sewn pocket, push the strap over the
metal support bar to prevent it from falling out.
NOTE: The hole in the metal bar should be in the center of the pocket opening. This is where the
S-hook of the chain or strap will be attached.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 6—ATTACHING SLING HARDWARE
DETAIL
“A”
DETAIL
“B”
Strap Over Metal
Support Bar
Metal Support Bars with
Openings for Chains or Straps
DETAIL “C”
Attaching the Chains or Adjustable Straps to the Sling
CAUTION
When using either the chains or straps to connect the sling to the patient lift, the short-
est of the two sections of the chains or straps MUST be attached to the back section of
the sling. Using the long section will leave little or no support for the patient’s back.
NOTE: For this procedure, refer to FIGURE 6.2 on page 25.
1. With the patient laying on his/her back and positioned properly in the sling, lay the
chains or straps on the bed next to the sling.
2. Place the short section of chain or strap parallel to the patient’s back.
NOTE: This will position the longer section of chain or strap from the waist to the mid section of
the thigh.
3. Insert the S-hooks on the ends of the chains or straps into the metal support bar of the
sling.
NOTE: The S-hook MUST be inserted through the hole in the support bar with the open end facing
NOTE: The O-ring of the chain assembly is the suggested location to attach to the swivel bar,
however, by changing to different links, you can reposition the patient into a reclining or more
upright position.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 6—ATTACHING SLING HARDWARE
ꢀ WARNING
When changing to different lengths, DO NOT disconnect the O-rings of the chains
from the swivel bar. Position both the O-rings and additional chain link onto the
hooks of the swivel bar.
NOTE: The straps can be simply adjusted to achieve the same effect.
4. With the sling positioned under the patient, and the metal support bars in place, you are
now ready to move the lift into position to attach the sling hardware to the swivel bar.
DETAIL “A”
S-Hook Open End
Away From Patient
Short Section
O-Ring
Long Section
S-Hook Open End
Away From Patient
DETAIL “B”
D-Ring
Short
Section
Long Section
S-Hook Open
End Away From
Patient
Adjust Buckles
25
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 7—OPERATION
SECTION 7—OPERATION
Operating the Patient Lift
Opening the Legs of the Adjustable Base
ꢀ WARNING
The operation of the patient lift is an easy and safe procedure. DO NOT attempt any
transfer without approval of the patient’s physician, nurse or medical assistant.
Thoroughly read the instructions in this Owner’s Manual, observe a trained team of
experts performing the lifting procedures and then perform the entire lift procedure
several times with proper supervision and a capable individual acting as a patient.
ONLY operate this lift with the legs in maximum open position and locked in place.
The base legs MUST be locked in the open position at all times for stability and
patient safety when lifting and transferring a patient.
NOTE: For this procedure, refer to FIGURE 7.1 on page 27.
The Shifter handle is used to open the legs of the base for stability when lifting a patient.
1. Grasp the shifter handle in one-hand and place the opposite hand on the steering
handle of the mast for balance.
2. Push the shifter handle to your right to release the lock pin from its mounting hole.
3. Turn the handle clockwise until you are able to secure the lock pin into the opposite
mounting hole to fully open the legs of the base.
NOTE: The lock pin MUST insert into its mounting hole in the socket assembly to lock the legs in
the full open position. The shifter handle will be in the vertical position; parallel with the mast
assembly.
ꢀ WARNING
If the shifter handle is NOT vertical, the lock pin is NOT seated in the socket assem-
bly. DO NOT use the patient lift until lock pin is properly seated and locked in place
or injury and/or damage may occur.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 7—OPERATION
DETAIL “A”
Base Closed
Base Open
Shifter
Handle
Shifter
Handle
Locked
DETAIL “B”
Step 1
Step 2
Step 3
Raising/Lowering Model Hydraulic Lifts
NOTE: For this procedure, refer to FIGURE 7.2 on page 28.
There are two controls on the pump assembly:
1. The control valve
2. The pump handle
Raising the Lift
The control valve MUST be in the closed position (control valve positioned towards pump
handle) to move the pump handle up and down to elevate the boom and the patient.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 7—OPERATION
Lowering the Lift
The control handle MUST be in the open position (control valve positioned away from
pump handle) to lower the boom and the patient. The rate of descent can be controlled by
varying the amount that the control valve is opened.
NOTE: A safety gate is part of the hydraulic system that maintains a SLOW constant descent of
the boom regardless of how far the control valve is opened.
Pump
Handle
Pump Handle
Closed
Control Valve
Open
28
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 8—LIFTING THE PATIENT
SECTION 8—LIFTING THE PATIENT
ꢀ WARNING
Before lifting or transferring the patient, the base legs MUST be locked in the open
position for optimum stability and safety.
Refer to General Guidelines on page 10 before proceeding further and observe all
WARNINGS indicated.
1. Using the steering handle, push the patient lift underneath the bed.
2. Lower the patient lift for easy attachment of the sling hardware or straps
3. Do one of the following:
• Chains, O-Rings and D-Rings: After the chains, O-Rings or D-Rings are attached
and the S-hooks are secured in both sides of the sling sections (open end facing
outward), place the D-rings of the strap assembly or the O-ring and chain link of
the chain assembly over the chain hooks of the swivel bar.
• Chain-Free All Fabric Slings: Attach the color-coded straps to the strap hooks of
the swivel bar.
Strap Hooks
Strap Hooks
Chain Hooks
4. Pump the lift handle or turn the handle clockwise (clicking sound is normal) to raise
the patient above the bed. The patient should be elevated high enough to clear the bed
and their weight supported by the lift.
NOTE: The manual (crank) lift handle will automatically turn back one quarter turn to lock in
place.
NOTE: On a hydraulic lift, the boom will stay in position until the control valve is opened.
5. When the patient is lifted from the bed (with the patient’s head supported), he/she will
29
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 8—LIFTING THE PATIENT
ꢀ WARNING
When elevated a few inches off the surface of the bed and before moving the
patient, check again to make sure that all hardware is properly connected. Check
each S-hook to make sure it is completely attached to the metal support bars of the
sling. Check the attachment of the straps, O or D-rings to the swivel bar hooks. If
any attachments are NOT properly in place, lower the patient back onto the bed
and correct this problem.
Adjustments for safety and comfort should be made before moving the patient.
Patient’s arms should be inside of the chains or straps.
Invacare slings and hardware are made specifically for use with Invacare Patient
Lifts. For the safety of the patient, DO NOT intermix slings and patient lifts of dif-
ferent manufacturers.
DETAIL “A” - AIDING THE PATIENT
DETAIL “B” - GUIDING THE PATIENT
30
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 8—LIFTING THE PATIENT
7. Using the steering handles, move the patient lift away from the bed.
8. When moving the patient lift away from the bed, turn patient so that he/she faces
assistant operating the patient lift (FIGURE 8.4).
9. Turn crank handle counterclockwise (manual) or open control valve (hydraulic)
lowering patient so that his feet rest on or over the base of the lift, straddling the mast.
Close control valve.
NOTE: The lower center of gravity provides stability making the patient feel more secure and the
lift easier to pull or push.
10. Pull the patient lift away from the bed and push from behind with both hands.
DETAIL “B” - MOVING THE PATIENT IN
THE LIFT
DETAIL “A” - TURNING THE PATIENT
31
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 9—BATHROOM
SECTION 9—BATHROOM
Transferring Patient for Use of Commode Chair or
Standard Commode
Transferring to a Commode Chair
ꢀ WARNING
When elevated a few inches off the surface of the commode chair or standard
commode and before moving the patient, check again to make sure that all
hardware or straps are properly connected. Check each S-hook to make sure it is
completely attached to the metal bars of the sling. Check the attachment of the
straps, O or D-rings to the swivel bar hooks. If any attachments are NOT properly
in place, lower the patient back onto the commode chair or standard commode to
correct this problem.
Adjustments for safety and comfort should be made before moving the patient.
Patient’s arms should be inside of the chains or straps.
Invacare slings and Hardware are made specifically for use with Invacare Patient
Lifts. For the safety of the patient, DO NOT intermix slings and patient lifts of dif-
ferent manufacturers.
NOTE: For this procedure, refer to FIGURE 9.1 on page 33.
NOTE: The slings with commode openings are designed to be used with either a commode chair or
standard commode.
NOTE: Invacare recommends that the sling remain connected to the swivel bar during the
patient’s use of either the commode chair or standard commode.
1. Elevate the patient high enough to clear the commode chair and their weight
supported by the lift.
2. With the help of both assistants, guide the patient onto the commode chair.
3. Lower the patient onto the commode chair leaving the sling attached to the swivel bar.
4. When complete, recheck for correct attachment and then raise the patient off the
commode chair.
5. When patient is clear of the commode surface (using the steering handles), move the
lift away from the commode chair.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 9—BATHROOM
DETAIL “A” - GUIDING THE PATIENT
DETAIL “B” - LOWERING THE PATIENT
Commode
Commode
Transferring to a Standard Commode
NOTE: For this procedure, refer to FIGURE 9.1.
NOTE: The patient MUST be transferred to a wheelchair and transported to the bathroom facilities
before using the patient lift again to position the patient on a standard commode.
2. Elevate the patient high enough to clear the standard commode and their weight
supported by the patient lift.
3. With the help of both assistants, guide the patient onto the standard commode.
4. Lower the patient onto the standard commode leaving the sling attached to the swivel
bar hooks.
5. When complete, recheck for correct attachment and then raise the patient off of the
standard commode.
6. When patient is clear of the standard commode surface (using the steering handles),
move the lift away from the standard commode.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 9—BATHROOM
Bathing
ꢀ WARNING
When elevated a few inches off the surface of the bed and before moving the
patient, check again to make sure that all hardware or straps are properly
connected. Check each S-hook to make sure it is completely attached to the metal
support bars of the sling. Check the attachment of the straps, O or D-rings to the
swivel bar hooks. If any attachments are NOT properly in place, lower the patient
completely to correct this problem.
Adjustments for safety and comfort should be made before moving the patient.
Patient's arms should be inside of the chains or straps.
Invacare slings and hardware are made specifically for use with Invacare Patient
Lifts. For the safety of the patient, DO NOT intermix slings and patient lifts of dif-
ferent manufacturers. Warranty will be voided.
NOTE: There are many portable bathing apparatuses. Refer to your particular portable bath
instructions and use them in conjunction with this Owner’s Manual.
2. Elevate the patient high enough to clear the commode chair and their weight
supported by the lift.
3. Lower the patient into the portable bath tub.
4. Detach chains/straps from sling and reattach to the portable bath tub.
5. Using the lift, raise the sides of the portable bath tub.
6. Bathe the patient.
7. Reverse procedures to return the patient to the bed.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 10—TRANSFERRING
SECTION 10—TRANSFERRING
Transferring to a Wheelchair
ꢀ WARNING
When elevated a few inches off the seating surface of the wheelchair and before
moving the patient, check again to make sure that all hardware and straps are
properly connected. Check each S-hook to make sure it is completely attached to
the metal support bars of the sling. Check the attachment of the straps, O or D-
rings to the swivel bar hooks. If any attachments are NOT properly in place, lower
the patient completely to correct this problem.
Adjustments for safety and comfort should be made before moving the patient.
Patient’s arms should be inside of the chains or straps.
Invacare slings and Hardware are made specifically for use with Invacare Patient
Lifts. For the safety of the patient, DO NOT intermix slings and patient lifts of dif-
ferent manufacturers.
NOTE: For this procedure, refer to FIGURE 10.1 on page 36.
NOTE: Invacare recommends that two assistants be used when transferring a patient to a
wheelchair.
1. Ensure the legs of the lift (w/patient) are in the opened position.
2. Move the wheelchair into position.
3. Lock the rear wheels to further prevent movement of the chair (Detail “A” of
ꢀ WARNING
Wheelchair wheel locks MUST be in a locked position before lowering the patient
into the wheelchair for transport.
4. Position the patient over the seat with their back against the back of the chair (Detail
5. Lower the patient either by doing one of the following:
• Open the control valve.
• Turn the crank counterclockwise.
6. The assistant behind the chair pulls back on either the handle or sides of the sling to
place the patient into the back of the chair. (Detail “C” of FIGURE 10.1).
NOTE: Holding the handle or sides of the patient lift maintains a good center of balance and
prevent the chair from tipping forward
7. Disconnect the sling from the patient lift.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 10—TRANSFERRING
Transferring to a Car
ꢀ WARNING
When elevated a few inches off the seating surface of the wheelchair and before
moving the patient, check again to make sure that all hardware or straps are
properly connected. Check each S-hook to make sure it is completely attached to
the metal support bars of the sling. Check the attachment of the straps, O or
D-rings to the swivel bar hooks. If any attachments are not properly in place, lower
the patient completely to correct this problem.
Adjustments for safety and comfort should be made before moving the patient.
Patient’s arms should be inside of the chains or straps.
Invacare slings and hardware are made specifically for use with Invacare Patient
Lifts. For the safety of the patient, DO NOT intermix slings and patient lifts of dif-
ferent manufacturers.
NOTE: For this procedure, refer to FIGURE 10.2 on page 38.
NOTE: To position an individual in a sling, follow the procedures concerning lifting the patient,
operation and sling attachments.
NOTE: Invacare recommends that two assistants be used when transferring a patient from a
wheelchair to a car.
NOTE: The transfer to a car should be made on a level driveway or surface.
NOTE: Before lifting the patient from the chair, make sure to shorten the distance between the
patient and the boom. This will make the transfer into the seat of the car easier.
NOTE: Assistants should practice ʺGood Body Mechanicsʺ (use your legs) when positioning
patient onto any seating surface.
1. Attach the chains or straps to swivel bar (Detail “A” of FIGURE 10.2).
2. Lock the rear wheels to further prevent movement of the chair (Detail “B” of
FIGURE 10.2).
3. Lift the patient from the wheelchair (Detail “C” of FIGURE 10.2).
4. Move the lift, by the steering handles, to a position close to the doorway of the car.
5. Lower the boom of the lift until it is about even with the roof of the car.
6. As one assistant pushes the patient into the car by his knees until he/she is positioned
over the seat of the car, the other assistant lowers the boom.
7. As the boom is being lowered, the first assistant is not only pushing but turning the
patient so he/she is positioned facing the front of the car (Detail “D” of FIGURE 10.2).
NOTE: The patient will come to rest on the seat of the car.
8. While one assistant is holding the patient, the other assistant removes the chains or
straps from the swivel bar and slides the patient lift out of the way (Detail “E” of
FIGURE 10.2).
NOTE: The sling may be left under the patient or removed (Detail “F” of FIGURE 10.2).
37
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 10—TRANSFERRING
9. If necessary, remove the mast, boom and pump assembly from the base and transport
them in the car.
NOTE: If the lift and wheelchair are both packed in the trunk of the car, care should be taken not
to damage the spokes of the wheelchair on the steering handles of the lift.
DETAIL “B” - LOCKING REAR WHEELS
DETAIL “A” - ATTACHING CHAINS
Swivel Bar
Wheel Lock
DETAIL “D” - LOWERING THE PATIENT
DETAIL “C” - LIFTING THE PATIENT
First Assistant
Patient
Wheelchair
DETAIL “E” - SETTING
DETAIL “F” - SLING PLACEMENT
First Asssitant
THE PATIENT
Second
Assistant
Sling
38
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 10—TRANSFERRING
Transferring from a Car to a Wheelchair
ꢀ WARNING
When elevated a few inches off the seat of the car and before moving the patient,
check again to make sure that all hardware or straps are properly connected. Check
each S-hook to make sure it is completely attached to the metal support bars of the
sling. Check the attachment of the straps, O or D-rings to the swivel bar hooks. If
any attachments are NOT properly in place, lower the patient completely to
correct this problem.
Adjustments for safety and comfort should be made before moving the patient.
Patient’s arms should be inside of the chains or straps.
Invacare slings and hardware are made specifically for use with Invacare Patient
Lifts. For the safety of the patient, DO NOT intermix slings and patient lifts of dif-
ferent manufacturers. Warranty will be voided.
NOTE: For this procedure, refer to FIGURE 10.3 on page 40.
NOTE: Invacare recommends that two assistants be used when transferring a patient from a car
to a wheelchair.
NOTE: One assistant MUST support patient at all times.
1. With the first assistant supporting the patient, the second assistant lowers the boom of
the patient lift until the hooks of the swivel bar are even with the roof of the car.
2. Attach the sling to the swivel bar (Detail “A” of FIGURE 10.3).
3. Lift the patient up off of seat until straps are taut.
4. Turn patient with sling until legs are outside of car.
NOTE: assistants should practice ʺGood Body Mechanicsʺ (use your legs) when positioning
patient onto any seating surface.
5. Lift up on legs with one hand and tilt the patient back with the other hand.
6. The second assistant should pull the patient lift away from the car until the patient is
completely clear of the door frame (Detail “B” of FIGURE 10.3).
7. Release the patient back to his/her normal sitting position in the sling.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 10—TRANSFERRING
DETAIL “A” -
ATTACHING THE
CHAINS
Sling
Chain
First Asssitant
DETAIL “B” -
REMOVING THE
PATIENT FROM
THE CAR
Patient
Lift
Second
Assistant
40
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 11—CARE AND MAINTENANCE
SECTION 11—CARE AND
MAINTENANCE
NOTE: Follow the maintenance procedures described in this manual to keep your patient lift in
continuous service.
The Invacare Patient Lift is designed to provide a maximum of safe, efficient and
satisfactory service with minimum care and maintenance.
All parts of the Invacare Lift are made of the best grades of steel, but metal to metal
contact will wear after considerable use.
There is no adjustment or maintenance the casters, other than cleaning, lubrication and
checking axle and swivel bolts for tightness. Remove all debris, etc. from the wheel and
swivel bearings. If any parts are worn, replace these parts IMMEDIATELY.
If you question the safety of any part of the lift, contact your Dealer IMMEDIATELY and
advise him/her of your problem.
Hydraulic Pump
All parts of the Hydraulic Pump are precision machined, then carefully assembled and
tested to ensure reliable service. The pump assembly is completely enclosed and sealed
with Neoprene rings to prevent leakage of hydraulic oil. A small amount of oil (about a
drop) will accumulate around the piston from time to time and should be removed with
a facial tissue.
ꢀ WARNING
The hydraulic pump is sealed at the factory and if service is required, the pump unit
MUST be returned to the factory for repair. DO NOT attempt to open the hydrau-
lic pump or obtain local service. This will void the warranty and might result in dam-
age and costly repair. Consult your Dealer or write Invacare for information.
Lubrication
The Invacare lift is designed for minimum maintenance; however, a six month check and
lubrication should ensure continued safety and reliability.
Keep lift and slings clean and in good working order. Any defect should be noted and
reported to your dealer as soon as possible.
The casters MUST swivel and roll smoothly. A light grease (waterproof auto lubricant)
may be applied to the ball bearing swivel of the casters once a year. Apply grease more
frequently if the casters are exposed to extreme moist conditions.
The connection between the mast and the base should be cleaned and coated with
petroleum jelly prior to assembly.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 11—CARE AND MAINTENANCE
Lubricate all pivot points. Wipe all excess lubricant from lift surface.
1. Swivel Bar at Mounting Bracket
2. Boom Mounting Bracket
3. Boom to Mast Mount
4. Mast Mounting Bracket
5. Base to Mast Mount
6. Rear Casters
7. Front Casters
Wear and Damage
It is important to inspect all stressed parts, such as slings, spreader bar and any pivot for
slings for signs of cracking, fraying, deformation or deterioration. Replace any defective
parts IMMEDIATELY and ensure that the lift is not used until repairs are made.
All sling metal parts should be inspected every three months, and if wear is apparent,
replacement must be made.
Check that all labels are present and legible. Replace if necessary.
Cleaning
The sling should be washed regularly in hot water (maximum temperature of 180°F
(82°C)) and a biological solution. A soft cloth, dampened with water and a small amount
of mild detergent, is all that is needed to clean the patient lift. The lift can be cleaned with
non-abrasive cleaners. Auto wax or furniture polish will help maintain the sparkling
finish over a long period of time.
Ensure that casters are free of debris.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 11—CARE AND MAINTENANCE
Maintenance Safety Inspection Checklist
ITEM
INITIALLY INSTITU- IN-HOME IN-HOME
TIONAL
INSPECT/
ADJUST
INSPECT/ INSPECT/
ADJUST ADJUST
EVERY SIX MONTHLY
MONTHLY MONTHS
CASTER BASE
Inspect for missing hardware.
Lift Base opens/closes with ease.
Inspect roll pin to ensure secure base.
Inspect casters and axle bolts for tightness.
Inspect casters for smooth swivel and roll.
Apply a light grease to caster ball bearings.
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
SHIFTER HANDLE
Operates smoothly.
Locks adjustable base whenever engaged.
Check roll pin for wear.
X
X
X
X
X
X
X
X
MAST
Mast should lock securely when assembled.
Inspect for bends or deflections.
X
X
X
X
X
X
BOOM
Check all hardware and swivel bar supports.
Inspect for bends or deflections.
Inspect bolted joints of boom for wear.
Inspect to ensure that the boom is centered
between the base legs.
X
X
X
X
X
X
X
X
X
X
X
X
X
SWIVEL BAR
Check the hooks for wear or damaged.
Check sling hooks for wear or deflection.
X
X
X
X
X
X
X
X
PUMP ASSEMBLY
X
X
X
X
X
X
X
X
X
X
X
X
Check for leakage.
Inspect hardware on mast and boom.
Check for wear or deflection of rod.
PUMP HANDLE
Check for smooth operation.
X
X
X
X
X
CONTROL VALVE
Easy to maneuver and closes easily.
CLEANING
Whenever necessary.
SLINGS AND HARDWARE
Chains, S-hooks, O-Rings and D-Rings each time it
is used to ensure proper connection and patient
safety.
Inspect sling attachments and material for wear.
Inspect nylon web straps for wear.
X
X
X
X
X
X
X
X
X
*NOTE: For individual home use, a full inspection is required prior to each new user.
**NOTE: Regular cleaning will reveal loose or worn parts, enhance smooth operation and extend
life expectancy of the lift.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
PLEASE NOTE: THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH
FEDERAL LAW APPLICABLE TO PRODUCTS MANUFACTURED AFTER JULY 4, 1975.
This warranty is extended only to the original purchaser/user of our products.
This warranty gives you specific legal rights and you may also have other legal rights which vary
from state to state.
Invacare warrants the products manufactured to be free from defects in materials and
workmanship for a period of three years on the lift and one year on the slings, hydraulic pump /
electric components from the date of purchase. If within such warranty period any such product
shall be proven to be defective, such product shall be repaired or replaced, at Invacare’s option.
This warranty does not include any labor or shipping charges incurred in replacement part
installation or repair of any such product. Invacare’s sole obligation and your exclusive remedy
under this warranty shall be limited to such repair and/or replacement.
For warranty service, please contact the dealer from whom you purchased your Invacare
product. In the event you do not receive satisfactory warranty service, please write directly to
Invacare at the address on the back cover, provide dealer’s name, address, date of purchase,
indicate nature of the defect.
Invacare Corporation will issue a serialized return authorization. The defective unit or parts
MUST be returned for warranty inspection using the serial number, when applicable as
identification within 30 days of return authorization date. Do not return products to our factory
without our prior consent. C.O.D. shipments will be refused; please prepay shipping charges.
LIMITATIONS AND EXCLUSIONS: THE FOREGOING WARRANTY SHALL NOT APPLY
TO SERIAL NUMBERED PRODUCTS IF THE SERIAL NUMBER HAS BEEN REMOVED OR
DEFACED, PRODUCTS SUBJECTED TO NEGLIGENCE, ACCIDENT, IMPROPER
OPERATION, MAINTENANCE OR STORAGE, PRODUCTS MODIFIED WITHOUT
INVACARE’S EXPRESS WRITTEN CONSENT (INCLUDING, BUT NOT LIMITED TO,
MODIFICATION THROUGH THE USE OF UNAUTHORIZED PARTS OR ATTACHMENTS;
PRODUCTS DAMAGED BY REASON OF REPAIRS MADE TO ANY COMPONENT
WITHOUT THE SPECIFIC CONSENT OF INVACARE, OR TO A PRODUCT DAMAGED BY
CIRCUMSTANCES BEYOND INVACARE’S CONTROL, AND SUCH EVALUATION WILL
BE SOLELY DETERMINED BY INVACARE. THE WARRANTY SHALL NOT APPLY TO
PROBLEMS ARISING FROM NORMAL WEAR OR FAILURE TO ADHERE TO THE
INSTRUCTIONS IN THIS MANUAL.
THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER EXPRESS
WARRANTIES. IMPLIED WARRANTIES, IF ANY, INCLUDING THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
SHALL NOT EXTEND BEYOND THE DURATION OF THE EXPRESSED WARRANTY
PROVIDED HEREIN AND THE REMEDY FOR VIOLATIONS OF ANY IMPLIED WARRANTY
SHALL BE LIMITED TO REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT
PURSUANT TO THE TERMS CONTAINED HEREIN. INVACARE SHALL NOT BE LIABLE
FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES WHATSOEVER.
SOME STATES DO NOT ALLOW EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGE, OR LIMITATION ON HOW LONG AN IMPLIED WARRANTY
LASTS, SO THE ABOVE EXCLUSIONS AND LIMITATIONS MAY NOT APPLY TO YOU.
THIS WARRANTY SHALL BE EXTENDED TO COMPLY WITH STATE OR PROVINCIAL
LAWS AND REQUIREMENTS.
Invacare Corporation
USA
Canada
One Invacare Way
Elyria, Ohio USA
44036-2125
570 Matheson Blvd E Unit 8 Invacare, the Medallion design, and Yes,
Mississauga Ontario
L4Z 4G4 Canada
800-668-5324
you can. are registered trademarks of
Invacare Corporation.
800-333-6900
© 2006 Invacare Corporation
Part No 1024492
Rev E - 05/23/06
Download from Www.Somanuals.com. All Manuals Search And Download.
|