DG 6145
Dishwasher
Installation and use
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Is a Good Habit to Get Into
NOTICE
- During installation, the power supply cord must not be
excessively or dangerously bent or flattened;
- If the appliance is not operating properly or maintenance
must be performed, disconnect the appliance from the
power supply.
Carefully read the instructions contained in this manual, as
they provide important information which is essential to
safe and proper installation, use and maintenance of the
appliance.
5.Keep detergents out of the reach of children, who must
also be kept away from the dishwasher when it is open.
6.This appliance cannot be installed outdoors, not even if
the area in which it is installed is covered by a roof; it is also
very dangerous to leave it exposed to the rain and elements.
7.Do not touch the heating element during or after a wash
cycle.
This appliance complies w ith the follow ing
EEC directives:
- 73/23/EEC of 19/02/73 (Low Voltage) and subsequent
modifications;
89/ 336/ EEC o f 03/ 05/ 89 (Ele ct ro m a g n e t ic
Compatibility) and subsequent modifications.
-
8.Do not lean or sit on the door when it is open, as this
could overturn the dishwasher.
1.Carefully dispose of the packing material.
2.After removing the packing, check to make sure that the
appliance is not damaged. If in doubt, contact a qualified
professional.
3.The dishwasher must only be used by adults for the
washing of household dishes and cooking utensils.
4.Fundamental rules to follow when using the appliance:
- Never touch the dishwasher when barefoot or with wet
hands or feet;
9.If the appliance malfunctions, turn off water supply to
the appliance and disconnect the plug from the wall socket.
Then, consult the section entitled, "Troubleshooting." If you
cannot resolve the problem, contact a service centre.
10.Only specialised personnel are authorised to make
repairs.
11.Appliances which are no longer being used must be
made inoperable by cutting the power supply cord and
removing the door lock.
- We discourage the use of extension cords and multiple
sockets;
Close-up View (control panel)
D
B
C
A
Handle For Opening Door
Knob For Selecting Cycles
ON - OFF Button
ON - OFF Light
GB
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Close-up View (Interior)
E
G
F
H
J
L
K
I
Upper Rack
Bottom Sprayer Arm
Salt Container Cap
Top Sprayer Arm
Rack Height Adjustor
Low er Rack
Washing Filter
Detergent and Rinse Aid Dispenser
Technical characteristics
Width
cm. 44,5
cm. 60
cm. 85
Depth
Height
Capacity
8 standard place settings
0,2 ÷10 bar (20 Kpa÷ 1 MPa)
See data plate
Mains water pressure
Power voltage
Total absorber power
Fuse
See data plate
See data plate
GB
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Salt...
Salt
Adjusting Salt Consumption
The hardness of the water varies from place to place. If
hard water is used in the dishwasher, deposits will form on
the dishes and utensils.
The dishwasher is designed to allow for adjusting the
amount of salt consumed based on the harness of the water
used. This is intended to
The appliance is equipped with a special softener that uses
a salt specifically designed to eliminate lime and minerals
from the water.
optimize and customize the level
of salt consumption so that it re-
mains at a minimum.
To adjust salt consumption,
Loading the Salt into the Softener
Always use salt intended for use with dishwashers.
The salt container is
proceed as follows:
1) Unscrew the cap from the salt
container.
located beneath the
2) There is a ring on the
lower rack and should be
container with an arrow on it
filled as follows:
(see figure to the side), if
1. Remove the lower rack
and then unscrew and
remove the cap from the
necessary, rotate the ring in the anticlockwise direction from
the "_" setting towards the "+" sign, based on the hard-
ness of the water being used.
salt container;
2. If you are filling the
It is recommended that adjustments be made in accordance
with the following schema:
container for the first
time, fill it with water;
3. Place the end of the
funnel (supplied) into the
Water Hardness
hole and introduce about 2 kg of salt. It is normal for a
small amount of water to come out of the salt container.
4. Carefully screw the cap back on.
Salt
Auto-
consu-
mption
(grams/-
cycle)
Clarke
degrees
Selector
position
nomy
(cycle-
s\2kg)
°dH
mmol/l
The salt container should be filled after about every 30 wash
cycles.
To prevent the formation of rust, load the salt just before
beginning a wash cycle.
0 ÷ 14
14÷ 36
36 ÷ 71
>71
0 ÷ 17
18 ÷ 44
45 ÷ 89
> 89
0 ÷ 1,7
1,8 ÷ 4,4
4,5 ÷ 8,9
> 8,9
/
0
/
20
40
60
60
40
25
-
MED
+
GB
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Detergent and Rinse Aid....
Detergent
Rinse Aid
Detergent specifically intended for use with dishwashers
must be used. The dispenser must be refilled before the
start of each wash cycle following the instructions provided
in the " Wash Cycle Table." The detergent dispenser is
located on the inside panel of the door.
This product makes dishes sparkle and helps them to dry
without spotting. The dispenser is located on the inside
panel of the door and should be filled after every 80 wash
cycles (or when the rinse aid indicator light comes on for
those models with this feature). .
Loading the Detergent
Loading the Rinse Aid
To open the " A" cover on the dispenser, press the " B"
button. The detergent for the wash cycle should be poured
into the " C" compartment.
After the detergent has been placed in the dispenser, close
the cover and press down until it clicks in place.
To open the dispenser, turn the "C" cap in the anti-clockwise
direction and then pour in the rinse aid, making sure not to
overfill. The amount of rinse aid used for each cycle can be
regulated by turning the "F" dose adjustor, located beneath
the " C" cap, with a screwdriver. There are 6 different
settings; the normal dosage setting is 2.
Important:
B
C
Proper dosage of the rinse aid improves drying.
If drops of water remain on the dishes or spotting occurs,
the dosage adjustor should be turned to a higher setting.
If the dishes have white streaks, turn the dosage adjustor
to a lower setting.
A
C
Notice: To facilitate closing the cover, remove any
excess detergent on the edges of the dispenser.
F
GB
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading the Dishw asher
Bottom Rack
Upper Rack
Before placing the dishes in the dishwasher, remove the
larger food particles to prevent the filter from becoming
clogged, which results in reduced performance.
If the pots and pans have baked-on food that is extremely
hard to remove, we recommend that they be allowed to
soak before they are washed. This will eliminate the need
for extra wash cycles.
Pull out the racks to facilitate loading the dishwasher.
How to Use the Low er Rack
We recommend that you place the most difficult to clean
items on the bottom rack: pots, pans, lids, serving dishes
and bowls, as shown in the figure to the right.
It is preferable to place serving dishes and lids on the
sides of the racks in order to avoid blocking the rotation
of the top spray arm.
Load for 8 Standard Settings (For IEC tests : top
rack at top position)
- Pots, serving bowls, etc. must always be placed top
down.
- Deep pots should be slanted to allow the water to flow
out.
- Silverware should be placed in the silverware basket
(see figure A) with the handles at the bottom; if the rack
has side baskets the spoons should be loaded individually
in the appropriate slots. Especially long utensils should be
placed in the horizontal position at the front of the upper
rack.
Fig. A
How to use the top rack …
The top rack is designed to hold delicate and light items,
such as glasses, tea and coffee cups, and saucers, as well
as plates, shallow serving bowls, and pans (as long as they
are not too dirty).
- Place these types of items so that they are not moved
around by the spray of water.
1
2
How to adjust the top rack ...
The top rack can be adjusted using the two rack heights
(top and bottom). To adjust the rack, open up the tabs
that lock the guides and pull out the rack. Arrange the
rack with the back wheels in either the top or bottom
position and then insert it along the guides until the front
wheels are on as well. Close the tabs to lock the rack in
place (see Fig. F).
3
Fig.F
4
GB
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning on the Appliance
Starting a w ash cycle....
If you forget to load some of the dishes...
1. Make sure that the plug for the appliance is inserted into
the wall socket.
2. Make sure that the water supply is turned on to full
pressure.
The wash cycle can be interrupted by pressing the ON-OFF
button. You can then load additional dishes and turn the
appliance back on. The cycle will start where it left off.
3. Load the dishwasher (see the section entitled, "Loading
the Dishwasher").
4. Pour in the detergent (see the section entitled, "Salt,
Detergent and Rinse Aid").
5. Turn the knob located on the right of the control panel in
the clockwise direction until the number or symbol for the
cycle setting is aligned with the reference mark (see the
section entitled, "Wash Cycle Table").
6. Press the ON-OFF botton, and the ON-OFF light will turn
on. At this point, the wash cycle will begin.
At the end of the w ash cycle...
When the knob stops turning and is aligned with a STOP
mark (see figure), the cycle has finished. Turn off the
appliance using the ON-OFF button, turn off the water supply
and open the door of the dishwasher.
Wait a few minutes before unloading the dishwasher to
avoid handling the dishes and utensils while they are still
hot and more susceptible to breakage. They will also dry
better.
Cancelling or modifying a w ash cycle setting...
Premise: A cycle that is underway can only be modified if it has
only been running for a short time. Otherwise, the detergent
may have already been used, and the appliance may have already
drained the wash water. If this is the case, the detergent dispenser
must be refilled (see the paragraph entitled, "Loading the
Detergent").
1
4
2
3
STOP
Press the ON-OFF button, and the ON light will turn off.
Rotate the knob in the clockwise direction to the desired
cycle setting (see the section entitled, " Starting a wash
cycle..."). Then, turn the dishwasher back on using the ON-
OFF button.
GB
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Wash Cycle Table
Cycle
Description of
Cycle
Detergent
20 gr.
20 gr.
Rinse Aid
Cycle
Selection
Information
Pre-wash with hot water
(45°C).
Ve ry d irty
dishes, pots and
pans (not to be
used with
Extended wash at 65°C.
Rinse with cold water.
Rinse with hot water at 70°C.
Drying.
*
*
delicate items).
1) Heavy Duty
Pre-wash with cold water.
Extended wash a 65°C.
Rinse with cold water.
Rinse with hot water at 70°C.
Drying.
Normally dirty
dishes, pots and
pans. Standard
daily cycle.
2) Normal Wash
(IEC-EN 50242)
Economic, fast
cycle to be used
to on not very
dirty dishes right
after they are
used. No drying
cycle.
Short wash at 65°C.
Cold rinse.
10 gr.
3) Rapid Wash
Pre-wash of
dishes, pots and
pans while
Short cold wash to prevent
food residue from drying on the
dishes.
waiting for the
load to be
completed after
the subsequent
meal.
4) Soak
GB
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Energy Saving Tips
- Use the right amount of detergent: if you use too much
detergent, the result will not be cleaner dishes, but, rather,
a greater negative impact on the environment.
- It is important to try and run the dishwasher when it is
fully loaded in order to save on energy. In order to prevent
odors from forming and food from caking onto the dishes,
you can run the hold cycle.
- There is no utility in rinsing dishes, cookware and utensils
before placing them in the dishwasher.
- Choose the right wash cycle: the choice of cycle depends
on the type of dishware, cookware and utensils being
washed and how dirty they are.
How to Keep Your Dishw asher in Shape
When You Go on Holiday
After Every Wash
When you go on holiday, it is recommended that you run a
wash cycle with the dishwasher empty and then remove
the plug from the socket, turn off the water supply and
leave the door of the appliance slightly ajar. This will help
the seals last longer and prevent odors from forming within
the appliance.
After every wash, turn off the water supply to the appliance
and leave the door slightly ajar so that moisture and odors
are not trapped inside.
Remove the Plug
Before cleaning or performing maintenance, always remove
the plug from the socket. Do not run risks.
Moving the Appliance
If the appliance must be moved, try to keep it in the vertical
position. If absolutely necessary, it can be positioned on its
back.
No Solvents or Abrasive Cleaning Products
To clean the exterior and rubber parts of the dishwasher,
do not use solvents or abrasive cleaning products. Rather,
use only a cloth and warm soapy water.
Seals
To remove spots or stains from the surface of the interior,
use a cloth dampened with water and a little white vinegar,
or a cleaning product made specifically for dishwashers.
One of the factors that cause odors to form in the
dishwasher is food that remains trapped in the seals. Periodic
cleaning with a damp sponge will prevent this from
occuring.
GB
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and Special Maintenance
Improper replacement of
Filter Assembly
the filters may reduce the
performance level of the
appliance and damage
dishes and utensils.
For best performance and results, the filter assembly must
be cleaned.
The filter efficiently removes food particles from the wash
water, allowing it to be recirculated during the cycle. For
this reason, it is a good idea to remove the larger food
particles trapped in the filter after each wash cycle by rinsing
the "A" semi-circular filter and cup under running water.
To remove the filter assembly, pull on the cup handle in the
upward direction. The entire filter assembly (made up of
A
B
Cle a n in g t h e Sp ra ye r
Arms
It may happen that food
particle become encrusted
on the sprayer arms and
the
" A"
semicircular filter
block the holes. Check the sprayer arms periodically and
clean them when needed. (See close-up view (interior)
lett.F-I)
and the " B" fine
filter) should be
cleaned at least
once a month.
Cleaning the Water Inlet Filter
To clean the filter
Periodically clean the water inlet filter (see figure 2 under
" Installation" ) located on the outlet of the water supply
tap.
and the fine filter,
use a cleaning
brush.
After turning off the water tap, unscrew the end of the
water supply hose, remove the filter and clean it carefully
under running water. Then, return the filter to its place and
tighten the water supply hose back into position.
Then, reassemble
the filter parts as shown in the figures below and reinsert
the entire assembly in the dishwasher, positioning in its
seat and pressing downward.
The dishwasher must never be used without the filters.
Troubleshooting
It may occur that the dishwasher does not function or does
not function properly. Before calling for assistance, let us
see what can be done first: have you forgot to press one of
the buttons or to perform an essential operation?
- the filter for the water supply hose is clogged.
The Dishw asher Does Not Drain
Have you checked whether:
- the drain hose is crimped or bent.
The Dishw asher Does Not Start
Have you checked whether:
- the plug is pushed into the socket correctly;
- the power is on in the house;
- the door is closed properly;
- the ON-OFF switch is on " ON" ;
Lime Deposits or a White Film Form on the Dishes
Have you checked whether:
- the lid to the salt container is closed properly;
- the rinse aid dosage is correct.
- the water supply is turned on.
The Dishw asher Does Not Load Water
Have you checked whether:
- the water is turned on and the hose is connected properly;
- the water supply to the house is on and has sufficient
pressure;
- the water supply hose is crimped or bent;
- the filter for the water supply hose is clogged.
The Dishes Are Not Clean
If, despite all these checks, the dishwasher still does not
function and/or the problem persists, contact the nearest
authorised service centre and provide them with the
following information:
- the nature of the problem;
- the model type number (Mod. ...) and the serial number
(S/N ....), which are indicated on the plate located on the
side of the inner part of the door.
Have you checked whether:
Never call on unauthorised technicians and refuse to
allow parts to be installed that are not original spare
parts.
- the water is turned on and the hose is connected properly;
- the water supply to the house is on and has sufficient
pressure;
- the water supply hose is crimped or bent;
GB
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Drain Hose Connection
Insert the drain hose into a
drain pipe with a minimum
diameter of 4 cm., or let it run
into the sink, making sure to
avoid bending or crimping it.
Use the speical plastic support
that comes with the appliance
(see figure to the right). The
free end of the hose must be
at a height between 40 and
100 cm and must not be
immersed in water.
Positioning the Appliance
Position the appliance in the desired location. The back
should rest against the wall behind it, and the sides, along
the adjacent cabinets or wall. The dishwasher is equipped
with water supply and drain hoses that can be positioned
to the right or the left to facilitate proper installation.
A
Levelling the Appliance
Once the appliance is positioned, adjust the feet (screwing
them in or out) to adjust the height of the dishwasher,
making it level. In any case, the appliance should not be
inclined more than 2°.
If the appliance is level, it will help ensure proper perfor-
mance.
Attention: The special plastic hose support must be solidly
fastened to the wall to prevent the drain hose from moving
and allowing water to spill outside the drain.
Cold Water Connection
Connect the cold water supply hose to a threaded 3/4 (gas)
connector, inserting the small filter supplied with the
dishwasher and making sure
Electrical Connection
After making sure that the voltage and frequency values
for the current in the home correspond to those on the
rating plate (located on the stainless steel inner door of the
appliance) and that the electrical system is sized for the
maximum voltage on the rating plate, insert the plug into
an electrical socket which is earthed properly (the earthing
of the appliance is a safety requirement mandated by law).
If the electrical socket to which the appliance must be
connected is not appropriate for the plug, replace the plug,
rather than using adpators or the like as they could cause
overheating and burns.
that it is fastened tightly in
place (see figure 2).
If the water pipes are new or
have not been used for an
extended period of time, let
the water run to make sure
that the water is clear and free
of impurities. If this precaution
is not taken, there is a risk that
A
fig. 2
the water inlet can get
blocked and damage the
appliance.
Hot Water Connection
The water supply to the appliance can also be connected
to the house's hot water line (centralised system, heating
system), as long as it does not exceed a temperature of
60° C.
In this case, the wash cycle time will be shortened by about
15 minutes and the wash efficiency slightly reduced.
The connection must be made to the hot water line
following the same procedures as those for the connection
to the cold water line.
GB
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connection
Electrical Connection
As the colours of the wires in the mains lead may not
correspond with the coloured markings identifying the
terminal in your plug, proceed as follows:
connect Green & Yellow wire to terminal market “E” or
coloured Green or Green & Yellow.
If your appliance is supplied with a 13 amp. fused plug it
can be plugged into a 13 amp socket for immediate use.
Before using the appliance please read the instruction below.
WARNING: THIS APPLIANCE MUST BE EARTHED.
THE FOLLOWING OPERATIONS SHOULD BE CARRIED
OUT BY A QUALIFIED ELECTRICIAN.
Connect Brown wire to terminal marked “L” or coloured
Red.
Connect Blue wire to terminal marked “N” or coloured
Black.
Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA approved
fuse to BS 1362 should always be used, and the fuse cover
re-fitted. If the fuse cover is lost, the plug must not be used
until a replacement is obtained.
If a 13 amp plug (BS 1363) is used it must be fitted with a
13 amp fuse. A15 amp plug must be protected by a 15
amp fuse, either in the plug or adaptor or at the
distribution board.
If you are in any doubt about the electrical supply to your
machine, consult a qualified electrician before use.
Replacemente fuse covers:
If a replacement fuse cover is fitted, it must be of the correct
colours as indicated by the coloured marking or the colour
that is embossed in words on the base of the plug.
Replacements can be obtained directly from your nearest
Service Depot.
How to connect an alternative plug:
The wires in this mains lead are coloured in accordance
with the following code:
Removing the plug:
BLUE
BROWN
GREEN AND YELLOW
“NEUTRAL” (“N”)
“LIVE” (“L”)
“EARTH” (“E”)
Ifyour appliance has a non-rewireable moulded plug and
you should wish to remove it to re-route the mains cable
through partitions, units etc., please esure that either:
- the plug is replaced by a fused 13 amp re-wireable plug
bearing the BSI mark of approval
- or:
GREEN &
YELLOW
- the mains cable is wired directly into a 13 amp cable outlet,
controlled by a switch, (in compliance with BS 5733) which
is accessible without moving the appliance.
13 amp fuse
BROWN
BLUE
Disposing of the plug:
CROSS-BAR
CORD GRIP
Ensure that before disposing of the plug itself, you make
the pins unusable so that it cannot be accidentally inserted
into a socket.
Instruction for connecting cable to an altenative plug:
Important: the wires in the mains lead are coloured in
accordance with the following code:
Green & Yellow
Blue
Brown
- Earth
- Neutral
- Live
Disposing of the appliance:
When disposing of the appliance please remove the plug
by cutting the mains cable as close as possible to the plug
body and dispose of it as described above
GB
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Viale Aristide Merloni 47
60044 Fabriano
tel. (0732) 6611 - Italy
Download from Www.Somanuals.com. All Manuals Search And Download.
|