MOW’N MACHINE
15 cu. ft. Metal Grasscatcher
For F-Series
Power Units
Tested. Proven. Unbeatable.
Download from Www.Somanuals.com. All Manuals Search And Download.
HOPPER ASSEMBLY
Assembly of hopper will be easier if assembled upside
down on a flat surface, see Figure 2. Note that Figure 1
shows hopper in the upright position.
ASSEMBLE HOPPER
!
LEA EL INSTRUCTIVO!
NOTE: When assembling the hopper, make sure bolts
that will interfere with grass clippings are installed with
heads on the inside. This will prevent clippings from
catching on bolts when the grasscatcher is dumped.
Si no lee Ingles, pida ayuda a
alguien que si lo lea para que le
traduzca las medidas de seguridad.
Leave hardware loose until hopper is assembled.
1. Lay top section upside down on a flat surface,
using Figure 1 as a guide for assembly.
„ Only use grass collection system with dual tail-
wheel option.
NOTE: Do not install bolts in side holes where
upper and lower crossmembers will mount (refer to
Figure 4, items 12 & 15).
2. Attach side panels (6, 7), upper front panel (8) and
back panel (9) to hopper top (1). Make sure side
panel corners are outside the front and back
panels as shown in Figure 2.
3. Fasten bottom panel (11) to the side panels and to
the outside of the front panel (Figure 1).
6
8
9
7
1
DP1
Figure 2. Assemble Hopper Upside Down
1. 70521 Hop-
per top
4. 70067 1/4 NC x 1/2 Whiz bolt
5. 70065 1/4 NC Whiz nut
6.1000664 Right side panel
7.1000665 Left side panel
8. 70528 Upper front panel
9. 70530 Back panel
11. 1000667 Bottom panel
Figure 1. Hopper Assembly
Assembly 3
MAN0115 (Rev. 3/31/2006)
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Make sure two pivot bearings (13), (Figure 4) are
attached to the inside of front cross channel (15)
using sheet metal screws (14). Do not tighten at
this time.
INSTALL CROSSMEMBERS
3. Slide left side door trip lever (17) through opening
on left side panel, pivot bearings (13) attached to
front cross channel (15), and right side panel.
Front Crossmember
4. Secure front cross channel (15) to bottom panel
using whiz bolts (4) and whiz nuts (5). Tighten
sheet metal screws.
5. Attach right dump lever (18) to door trip lever (17),
so that both bars face forward. Secure using cap
screw (19) and lock nut (20).
6. Mount rear cross channel (12) on outside of bottom
panel using whiz bolts (4) and whiz nuts (5) as
shown. Make sure pivot hinge is at the bottom.
DP7A
7. Attach left and right door hinge mounts (26, 27) to
back and side panels as shown in Figure 5. Use
whiz bolt (10) and whiz nut (5) to secure hinge
mount to back panel.
Figure 3. Side Panel & Front Crossmember Installed
10
5
4
5
26
4. 70067 1/4 NC x 1/2 Whiz bolt
5. 70065 1/4 NC Whiz nut
12.1000679 Rear cross channel
13. 71163 Pivot bearing
14. 27610 5/16 x 3/4 Sheet metal screw
15.1000680 Front cross channel
17.1000677 Left side door trip lever
18.1000678 Right dump lever
4. 70067 1/4 NC x 1/2 Whiz bolt
5. 70065 1/4 NC Whiz nut
10. 70068 1/4 NC x 3/4 Whiz bolt
26. 70536 Right door hinge
19.
20.
3184 1/4 NC x 1-1/4 HHCS
6128 1/4 NC Lock nut
Figure 5. Right Door Hinge Mount Installation
26. 70536 Right door hinge
27. 70537 Left door hinge
INSTALL DOOR
NOTE: 90° bend on latch bracket faces forward.
1. Attach latch brackets (28) to bottom of door (24).
2. Place nylon bearings (23) into door hinge mounts.
Figure 4. Crossmember Installation
NOTE: Hopper should still be upside down. Do not
tighten hardware.
3. Insert both left and right door hinges (26, 27) into
door hinge mounts.
1. Install front crossmember (16) between right and
left side panels. Install crossmember with brackets
facing forward as shown in Figure 3.
4. Place door (24) over hinges and secure with whiz
bolt (4, 10) and whiz nut (5).
(Rev. 8/17/2007)
4 Assembly
MAN0115 (Rev. 3/31/2006)
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Torque all hardware according to page 8.
2. Attach latch linkage rod (36) to both right and left
door handle mount. Be sure to install spring
bracket (35) into clevis when attaching left side
(see Figure 7).
3. Attach opposite end of door linkage rod (45) to
door handle mount.
4. Adjust linkage so that there is a slight amount of
pressure holding the door closed when handle is
snapped over center.
5. Attach opposite end of latch linkage rod to door
latches.
6. Attach spring (34) to hole in side panel with spring
anchor (35) on left side and to spring bracket (33)
as shown in Figure 7.
7. Adjust latch linkage rods so that the door latches
will release just before the door opens when the
door handle is moved forward.
4. 70067 1/4 NC x 1/2
Whiz bolt
5. 70065 1/4 NC Whiz nut
10. 70068 1/4 NC x 3/4 Whiz bolt
23. 70026 Nylon bearing
24. 70531 Door
48
39
40
29
31
32
26. 70536 Right door hinge
27. 70537 Left door hinge
45
39
40
40
36
Figure 6. Door Assembly
INSTALL DOOR HANDLE
NOTE: Turn hopper assembly over and support in
upright position.
33
34
35
29. 70526 Hopper handle
31. 1686 3/8 NC x 3/4 HHCS
1. Attach door handle (29) to left door handle mount
as shown in Figure 7.
2. Install stop lever (49) and rubber bumper (50) to
right side panel as shown in Figure 8.
32. 15030 3/8 NC Flange lock nut
33. 70546 Link
3. Install latch pivot bracket (42) to both sides of
grasscatcher as shown in Figure 8.
34. 70834 Spring
35.1001501 Spring anchor bracket
36. 70547 Linkage latch rod
4. Attach door latches (44) to latch pivot brackets.
Adjust latch brackets (28) so that the door latches
will hold the door tightly shut (see Figure 8).
39. 70024 Clevis pin, 5/16 x 25/32
40. 1326 Cotter pin, 1/8 x 1/2
INSTALL LINKAGE
45. 70548 Linkage door rod
1. Attach door linkage rod (36) to both right and left
door hinge as shown in Figure 7 and Figure 8.
Place head of clevis pin to the outside.
48. 64151 Clevis pin, 3/8 x 1-1/8
Figure 7. Left Side
Assembly 5
MAN0115 (Rev. 3/31/2006)
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Install rubber bumpers (19). Secure with flange
lock nuts (13).
48
40
5
1
9
45
36
8
49
50
7
19
13
28
2
42
5
41
39 40
40
44
4
6
7
4. 70067 1/4 NC x 1/2 Whiz bolt
5. 70065 1/4 NC Whiz nut
28. 70538 Latch bracket
36. 70547 Linkage latch rod
39. 70024 Clevis pin
1. 74082 Right hopper support
2. 74083 Left hopper support
5. 74084 Cross brace
40.
41.
1326 Cotter pin, 1/8 x 1/2
4378 5/16 Flat washer
6.
920 3/8 NC x 1-3/4 Cap screw GR5
42. 70543 Latch pivot bracket
44. 70545 Left side door latch
45. 70548 Linkage door rod
48. 64151 Clevis pin
7. 15030 3/8 NC Flanged lock nut
8. 62153 3/8 NC Flanged screw
9.
565 Flat Washer
13. 14139 5/16 NC Flange lock nut
19. 71444 Rubber bumper
49.1000670 Lever stop
50. 71444 Rubber bumper
Figure 8. Right Side
Figure 9. Hopper Mounting (Left Side Shown)
INSTALL HOPPER SUPPORTS
1. Remove two center 3/8 NC x 3/4 hex washer head
cap screws from both right and left side of hood
assembly. Note: Drill completely through hood
frame if not already done.
2. Attach left hopper support (2) to hood assembly.
Secure using two cap screws (6) and flange screw
(7) as shown in Figure 9.
3. Repeat steps 1 & 2 to install right support (1).
4. Install cross brace (5) between hopper supports.
Secure with cap screws (8), washer (9), and lock
nut (7). See Figure 10.
Figure 10. Mounting Bracket Instructions
(Rev. 8/17/2007)
6 Assembly
MAN0115 (Rev. 3/31/2006)
Download from Www.Somanuals.com. All Manuals Search And Download.
Align hinges of rear crossmember (12) on hopper with
hinges of rear hopper pivot (4). Insert clevis pins (14)
and hair pins (15) as shown in Figure 12.
INSTALL REAR HOPPER SUPPORT &
REAR HOPPER PIVOT
1. Attach rear hopper support (3) to the rear of the
power unit using four flanged head cap screws (8),
standard flat washers (9), and two flange lock nuts
(7) as shown in Figure 11.
ATTACH CABLE
1. Attach cable (10) to rear of power unit on both right
and left sides as shown in Figure 13.
NOTE: Remove cap screw for ground cable on
21D & 25L power units.
2. Attach the rear hopper pivot (4) to the rear hopper
support using four flanged head cap screws (8),
washers (9), and flange lock nuts (7).
2. Secure with flanged cap screw (8), washer (9), and
flange lock nut (7). Leave hardware loose at this
time.
3. Remove the fourth whiz bolt and whiz nut from the
bottom of both right and left side panels.
7
8
9
4. Install whiz bolt (16), other end of cable (10), flat
washer (9), and whiz nut previously removed in this
hole position as shown in Figure 13.
4
5. Pivot hopper back and allow weight of hopper on
8
7
cables. Torque hardware at this time.
3
16
9
8
7
9
DP4
10
3. 74082 Rear hopper support
4. 73678 Rear hopper pivot
7. 15030 3/8 NC Flange lock nut
8. 62153 3/8 NC x 1 Flanged cap screw
9. 565 3/8 Standard flat washer
Figure 11. Rear Hopper Support & Rear Hopper Pivot
7
9
8
7. 15030 3/8 NC Flange lock nut (2)
8. 62153 3/8 NC Flanged cap screw (2)
MOUNT HOPPER ASSEMBLY
9.
565 3/8 Flat washer (4)
12
10. 73957 Cable
16. 70068 1/4 NC x 3/4 Whiz bolt (2)
Figure 13. Cable Installed (Right Side Shown)
4
14
15
4. 73678 Rear hopper pivot
12. 1000679 Rear cross channel (Hopper)
14. 63523 3/4 x 4-1/2 Clevis pin (2)
15.
2688 5/32 Hair pin cotter (2)
Figure 12. Hinge Pin Installed (Left Hinge Shown)
(Rev. 8/17/2007)
Assembly 7
MAN0115 (Rev. 3/31/2006)
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Tilt hopper assembly back.
SECURE HOPPER
1. Rotate hopper onto right and left hopper supports.
NOTICE
2. Insert 3/8 lynch pins (18) to attach front hopper
crossmember to support brace as shown in Figure
14.
■
Do not attempt to tilt hopper to service position
unless hopper is completely empty. Failure to
empty hopper could result in damage to hopper.
4. On power unit, unhook rubber latches and lift hood
assembly to service position.
5. Secure with prop rod.
18
18. 33000 3/8 x 2-1/4 Lynch pins
Figure 14. Latch Locked into Position
POSITION HOOD FOR SERVICING ENGINE
DP5
To flip hood up for servicing engine, follow these steps:
1. Disconnect vacuum hose from hose adapter chute
Figure 15. Servicing Engine
on vacuum.
2. Remove lynch pins from hopper support (Figure
14).
TORQUE SPECIFICATIONS
Wrench
Size
Hardware
Location
Ref
4
Cap Screw
1/4 NC x 1/2 Whiz bolt
3/8 NC x 1-3/4 HHCS
3/8 NC x 1 FHCS
Qty
68
4
Required Torque
10 lbs-ft (13 N-m)
35 lbs-ft (47 N-m)
35 lbs-ft (47 N-m)
10 lbs-ft (13 N-m)
19 lbs-ft (26 N-m)
10 lbs-ft (13 N-m)
35 lbs-ft (47 N-m)
7/16
9/16
9/16
7/16
1/2
Hopper Assembly
Mount Assembly
Mount Assembly
Hopper Assembly
Hopper Assembly
Hopper Assembly
Hopper Assembly
6
8
12
14
4
10 1/4 NC x 3/4 Whiz bolt
14 5/16 x 3/4 Sheet metal screw
19 1/4 NC x 1-1/4 HHCS
31 3/8 NC x 3/4 HHCS
1
7/16
9/16
2
8 Assembly
MAN0115 (Rev. 3/31/2006)
Download from Www.Somanuals.com. All Manuals Search And Download.
MOUNT ASSEMBLY
REF PARTS QTY
DESCRIPTION
Right hopper support
REF PARTS QTY
DESCRIPTION
1
2
74082
74083
73677
73678
74084
920
1
1
1
1
1
4
11
12
13
14
15
16
17
18
19
4528
6778
4
4
2
2
2
2
2
2
2
5/16 NC x 1-3/4 Cap screw GR5
5/16 NC Lock nut
Left hopper support
3
Rear hopper support
Rear hopper pivot
14139
63523
2688
5/16 NC Flange lock nut
3/4 x 4-1/2 Clevis pin
5/32 Hair pin cotter
1/4 x 3/4 Whiz bolt
1/4 Whiz nut
4
5
Hopper cross brace
6
3/8 NC x 1-3/4 Cap screw GR5
70068
70065
33000
71444
7
15030 12 3/8 NC Flange lock nut
8
62153 12 3/8 NC x 1 Flanged head cap screw
3/8 x 2-1/4 Lynch pin
Rubber bumper
9
565
8
2
3/8 Standard flat washer
Cable assembly
10
73957
Parts 9
MAN0115 (Rev.3/31/2006)
Download from Www.Somanuals.com. All Manuals Search And Download.
HOPPER ASSEMBLY
10 Parts
MAN0115 (Rev. 3/31/2006)
Download from Www.Somanuals.com. All Manuals Search And Download.
HOPPER ASSEMBLY PART LIST
REF PARTS QTY
DESCRIPTION
Hopper top
REF PARTS QTY
DESCRIPTION
Latch bracket
1
70521
70504
70505
1
1
2
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
70538
70526
70527
1686
2
1
1
2
2
1
1
1
2
2
2
2
8
9
1
1
1
2
2
2
2
1
1
1
1
1
2
Window
Hopper handle
3
Mounting bracket
Handle grip, .812 x 4
3/8 NC x 3/4 HHCS
3/8 NC Flange lock nut
Link, .19 x .75 x 4.0
Spring
4
70067 68 1/4 NC x 1/2 Whiz bolt
70065 82 1/4 NC Whiz nut
5
15030
70546
70834
1001501
70547
5283
6
1000664
1000665
70528
1
1
1
1
Right side panel
Left side panel
Upper front panel
Back panel
7
8
Spring anchor bracket
Linkage latch rod
5/16 NF Hex nut
9
70530
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
70068 14 1/4 NC x 3/4 Whiz bolt
1000667
1000679
71163
1
1
2
4
1
1
1
1
1
1
1
1
2
1
1
2
2
Bottom panel
70022
70024
1326
Adjustable clevis, 5/16 NF
Clevis pin, 5/16 x 25/32
Cotter pin, 1/8 x 1/2
5/16 Flat washer
Rear cross channel
Pivot bearing
27610
1000680
74085
1000677
1000678
3184
5/16 x 3/4 Sheet metal screw
Front cross channel
Front crossmember
Left door trip lever
Right dump lever
1/4 NC x 1-1/4 HHCS
1/4 NC Lock nut
4378
70543
70544
70545
70548
1271
Latch pivot bracket
Right side door latch
Left side door latch
Linkage door rod
3/8 NF Hex nut
6128
70360
64151
1000670
71444
14139
1001018
70523
Adjustable clevis, 3/8NF
Clevis pin, 3/8 x 1-1/8
Lever stop
70534
70535
70026
70531
70552
70536
70537
Right door hinge mount
Left door hinge mount
Nylon bearing (included. w/ 21 & 22)
Door
Rubber bumper
5/16 NC Flange lock nut
64" Flex hose
Door seal
Right door hinge
6" Hose clamp
Left door hinge
Parts 11
MAN0115 (Rev.3/31/2006)
Download from Www.Somanuals.com. All Manuals Search And Download.
BOLT TORQUE CHART
Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific
application.
Fasteners must always be replaced with the same grade as specified in the manual parts list.
Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware.
Make sure fastener threads are clean and you start thread engagement properly.
All torque values are given to specifications used on hardware defined by SAE J1701 MAR 99 & J1701M JUL 96.
SAE Bolt Head
Identification
SAE SERIES
TORQUE
CHART
A
SAE Grade 2
(No Dashes)
SAE Grade 8
(6 Radial Dashes)
SAE Grade 5
(3 Radial Dashes)
MARKING ON HEAD
A
SAE 2
SAE 5
SAE 8
Diameter
(Inches)
Wrench
Size
lbs-ft
N-m
8
lbs-ft
10
N-m
13
lbs-ft
14
N-m
1/4"
5/16"
3/8"
7/16"
1/2"
9/16"
5/8"
3/4"
7/8"
1"
7/16"
1/2"
6
18
37
12
17
19
26
27
9/16"
5/8"
23
31
35
47
49
67
36
48
55
75
78
106
163
232
325
569
907
1383
3/4"
55
75
85
115
164
230
403
642
979
120
171
240
420
669
1020
13/16"
15/16"
1-1/8"
1-5/16"
1-1/2"
78
106
149
261
416
634
121
170
297
474
722
110
192
306
467
METRIC SERIES
TORQUE
CHART
8.8
Metric Bolt Head
Identification
10.9
A
Metric
Grade 8.8
Metric
Grade 10.9
COARSE THREAD
FINE THREAD
A
A
MARKING ON HEAD
MARKING ON HEAD
Diameter &
Thread Pitch Wrench
(Millimeters)
Diameter &
Thread Pitch
(Millimeters)
Metric 8.8
Metric 10.9
N-m lbs-ft
Metric 8.8
Metric 10.9
N-m lbs-ft
Size
N-m
lbs-ft
6
N-m
lbs-ft
6
6 x 1.0
10 mm
13 mm
16 mm
18 mm
21 mm
24 mm
27 mm
30 mm
34 mm
36 mm
46 mm
8
11
27
8
8
11
29
8
6 x 1.0
8 x 1.0
8 x 1.25
10 x 1.5
12 x 1.75
14 x 2.0
16 x 2.0
18 x 2.5
20 x 2.5
22 x 2.5
24 x 3.0
30 x 3.0
20
15
20
21
16
22
39
29
54
40
41
30
57
42
10 x 1.25
12 x 1.25
14 x 1.5
16 x 1.5
18 x 1.5
20 x 1.5
22 x 1.5
24 x 2.0
30 x 2.0
68
50
94
70
75
55
103
163
250
363
507
684
861
1740
76
109
169
234
330
451
571
1175
80
151
234
323
457
623
790
1626
111
173
239
337
460
583
1199
118
181
263
367
495
623
1258
87
120
184
268
374
505
635
1283
125
172
244
332
421
867
133
194
270
365
459
928
Typical Washer
Installations
Bolt
Flat Washer
Lock Washer
8/9/00
Bolt Torque & Size Charts (Rev. 10/10/2005)
12 Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
BOLT SIZE CHART
NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts.
SAE Bolt Thread Sizes
5/16
3/8
1/2
5/8
3/4
7/8
IN
1
2
7
3
4
5
6
MM
25
50
75
100
125
150
175
Metric Bolt Thread Sizes
8MM 10MM
12MM
14MM
16MM
18MM
ABBREVIATIONS
AG.............................................................Agriculture
ATF...............................Automatic Transmission Fluid
BSPP .......................... British Standard Pipe Parallel
BSPTM...............British Standard Pipe Tapered Male
CV.................................................. Constant Velocity
CCW ............................................ Counter-Clockwise
CW............................................................. Clockwise
F..................................................................... Female
GA................................................................... Gauge
GR (5, etc.) .........................................Grade (5, etc.)
HHCS.......................................Hex Head Cap Screw
HT ......................................................... Heat-Treated
JIC............... Joint Industry Council 37° Degree Flare
LH ...............................................................Left Hand
LT ......................................................................... Left
m.......................................................................Meter
mm ..............................................................Millimeter
M........................................................................ Male
MPa........................................................Mega Pascal
N ....................................................................Newton
NC ....................................................National Coarse
NF......................................................... National Fine
NPSM ...................National Pipe Straight Mechanical
NPT ........................................ National Pipe Tapered
NPT SWF .......National Pipe Tapered Swivel Female
ORBM......................................... O-Ring Boss - Male
P .........................................................................Pitch
PBY .................................................... Power-Beyond
psi........................................Pounds per Square Inch
PTO ................................................... Power Take Off
QD ..................................................Quick Disconnect
RH ............................................................Right Hand
ROPS..........................Roll-Over Protective Structure
RPM.......................................Revolutions Per Minute
RT...................................................................... Right
SAE ........................Society of Automotive Engineers
UNC....................................................Unified Coarse
UNF ........................................................ Unified Fine
UNS....................................................Unified Special
Bolt Torque & Size Charts (Rev. 10/10/2005)
Appendix 13
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
TM
(Mow’n Machine Zero-Turn Mower and
TM
Woods Boundary Utility Vehicle Replacement Parts)
TM
Woods Equipment Company (“WOODS”) warrants replacement parts for Mow’n Machine zero-turn
TM
mowers and attachments and Woods Boundary utility vehicles, accessories and attachments to be free
from defect in material and workmanship for a period of ninety (90) days from the date of delivery of the
product to the original purchaser.
IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR
PURPOSE ARE LIMITED IN DURATION TO A PERIOD OF NINETY (90) DAYS FROM THE
DATE OF DELIVERY OF THE PRODUCT TO THE ORIGINAL PURCHASER. Some states do not
allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser
sell or otherwise transfer the product to a third party, this Warranty does not transfer to the third party
purchaser in any way. There are no third party beneficiaries of this Warranty.
This Warranty does not cover normal wear or tear, or normal maintenance items, or any damage, failure
or loss caused by improper operation, improper maintenance, misuse, or an accident.
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement,
free of charge, of the product if the product is defective or in noncompliance with this Warranty. The
product must be returned to WOODS with proof of purchase within thirty (30) days after such
defect or noncompliance is discovered or should have been discovered, routed through the dealer
and distributor from whom the purchase was made, transportation charges prepaid. WOODS
shall complete such repair or replacement within a reasonable time after WOODS receives the product.
WOODS shall not be liable for any incidental or consequential losses, damages or expenses,
arising directly or indirectly from the product, whether such claim is based upon breach of
contract, breach of warranty, negligence, strict liability in tort or any other legal theory. Without
limiting the foregoing, WOODS shall not be liable for any damages relating to (i) lost profits, business,
revenues or goodwill; (ii) any expense or loss incurred for labor, supplies, substitute machinery or rental;
or (iii) any other type of damage to property or economic loss. Some states do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitations may not apply to you.
No agent, representative, dealer, distributor, service person, salesperson, or employee of any company,
including without limitation, WOODS, its authorized dealers, distributors, and service centers, is
authorized to alter, modify, or enlarge this Warranty.
This Warranty gives you specific legal rights, and you may also have other rights which may vary from
state to state.
Answers to any questions regarding warranty service and locations may be obtained by contacting:
Woods Equipment
Company
2606 South Illinois Route 2
Post Office Box 1000
Oregon, Illinois 61061
800-319-6637 tel
800-399-6637 fax
F-8495 MM & Boundary Repair Parts (Rev. 2/15/2006)
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
(Mow’n Machine Zero-Turn Mowers and Woods Boundary Utility Vehicles)
TM
TM
Please Enter Information Below and Save For Future Reference.
Date Purchased: __________________________
Model Number: __________________________
WHAT IS COVERED:
From (Dealer): _____________________________________
Serial Number: _____________________________________
TM
TM
Woods Equipment Company (“WOODS”) warrants Mow’n Machine zero-turn mowers and attachments and Woods Boundary utility
vehicles, accessories and attachments to be free from defect in material and workmanship for the warranty periods listed below.
FOR HOW LONG:
Mow’n Machine Model #CZ2136B, CZ1736K, CZ1942K, CZ1948K, CZ1952K, FE21B, FZ23B, FZ25D, FZ28K, ME2052B, MZ1952K,
MZ2652G, MZ2561K, MZ2761, MZ3361G, MZ3372G, MZ2061YD & attachments are warranted for two (2) years from the date of
delivery to the original purchaser or 2000 hours of operation, whichever occurs first.
Mow’n Machine ME and MZ Series Models, serial number XXXXXXXX300 and above, Limited Lifetime Warranty on deck, deck cradle,
and engine deck for the life of the machine to the original retail purchaser.
Woods Boundary utility vehicle Model #MAV350, MAV480, MAV4x4, accessories & attachments are warranted for two (2) years from the
date of delivery to the original purchaser.
IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN
DURATION TO THE DURATION OF THE WRITTEN WARRANTY PERIODS LISTED ABOVE. Some states do not allow limitations
on how long an implied warranty lasts, so the above limitation may not apply to you.
WHO IS COVERED:
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell or otherwise transfer the
product to a third party, this Warranty does not transfer to the third party purchaser in any way. There are no third party beneficiaries of this
Warranty.
WHAT IS NOT COVERED:
This Warranty does not cover normal wear or tear, or normal maintenance items, or any damage, failure or loss caused by:
1. Improper operation, improper maintenance, misuse, or an accident;
2. Any modification or repair by someone other than WOODS, a WOODS authorized dealer or distributor, and/or a WOODS
authorized service center; or
3. Repairs made with parts other than those obtainable through WOODS.
WOODS makes no warranty, express or implied, with respect to engines, batteries, tires or other parts or accessories not manufactured by
WOODS. Warranties for these items, if any, are provided separately by their respective manufacturers.
WHAT WOODS WILL DO TO CORRECT PROBLEMS:
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of charge, of the product if the
product is defective or in noncompliance with this Warranty. The product must be returned to WOODS with proof of purchase within thirty
(30) days after such defect or noncompliance is discovered or should have been discovered, routed through the dealer and distributor from
whom the purchase was made, transportation charges prepaid. WOODS shall complete such repair or replacement within a reasonable time
after WOODS receives the product.
OTHER LIMITATIONS:
WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising directly or indirectly from the
product, whether such claim is based upon breach of contract, breach of warranty, negligence, strict liability in tort or any other
legal theory. Without limiting the foregoing, WOODS shall not be liable for any damages relating to (i) lost profits, business, revenues or
goodwill; (ii) any expense or loss incurred for labor, supplies, substitute machinery or rental; or (iii) any other type of damage to property
or economic loss. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations may
not apply to you.
No agent, representative, dealer, distributor, service person, salesperson, or employee of any company, including without limitation,
WOODS, its authorized dealers, distributors, and service centers, is authorized to alter, modify, or enlarge this Warranty.
HOW STATE LAW APPLIES:
This Warranty gives you specific legal rights, and you may also have other rights which may vary from state to state.
QUESTIONS:
Answers to any questions regarding warranty service and locations may be obtained by contacting:
Woods Equipment
Company
2606 South Illinois Route 2
Post Office Box 1000
Oregon, Illinois 61061
800-319-6637 tel
800-399-6637 fax
F-8045 MM & Boundary (Rev. 7/6/2007)
Download from Www.Somanuals.com. All Manuals Search And Download.
PART NO.
MAN0115
Woods Equipment
Company
2606 South Illinois Route 2
Post Office Box 1000
Oregon, Illinois 61061
800-319-6637 tel
800-399-6637 fax
© 2001 Woods Equipment Company. All rights reserved. WOODS, the Woods logo, and "Tested. Proven. Unbeatable." are trademarks of Woods
Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual
are the property of their respective companies or mark holders. Specifications subject to change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
|