OPERATOR’S MANUAL
21” MULCHING PUSH
MOWER
MODEL NO:
HW-615
FACTORY NO:
11A-599B190
IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-
Warning:
covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting
applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.
In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have
similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized
service dealer or contact the service department, P.O. Box 361131 Cleveland, Ohio 44136-9722.
WHITE OUTDOOR PRODUCTS COMPANY P.O. BOX 361131 CLEVELAND, OHIO 44136-9722
PRINTED IN U.S.A.
FORM NO. 770-10060
(10/98)
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1: CALLING WARRANTY SERVICE
If you are having difficulty assembling this product or if you have any question regarding the controls, operation or
maintenance of this unit, please call the Customer Dealer Referral Line. You can reach them by calling:
1-800-949-4483
Before calling your local dealer, make sure that you have your model and serial numbers ready. By having the
model and serial numbers ready, you help your local dealer give you faster service. To find your unit’s model and
serial number, see SECTION 2: FINDING YOUR MODEL NUMBER.
SECTION 2: FINDING YOUR MODEL NUMBER
This Operator’s Manual is an important part of your new walk behind. It will help you assemble, prepare and
maintain your walk behind. Please read and understand what it says.
Before you start to prepare your walk behind for its first use, please locate the model plate and copy the information
from it in this Operator’s Manual. The information on the model plate is very important if you need help from your
dealer.
• Every walk behind has a model plate. You can locate it by standing behind the unit in the operating position
and looking down at the rear of the deck.
• The model plate will look like Figure 1.
This is where your model number will be.
XXX-X-XXX-X-XXX XXXXXXXXXXX
This is where your serial number will be.
Copy the model number here:
WHITE OUTDOOR
PRODUCTS COMPANY
P.O. BOX 361131
CLEVELAND, OHIO 44136
Copy the serial number here:
FIGURE 1
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 3: IMPORTANT SAFE OPERATION PRACTICES
This symbol points out important safety instructions which, if not followed, could endanger the
personal safety and/or property of yourself and others. Read and follow all instructions in this manual
before attempting to operate your lawn mower. Failure to comply with these instructions may result in
personal injury. When you see this symbol—heed its warning.
Your lawn mower was built to be operated according to the rules for safe operation in this manual.
DANGER:
As with any type of power equipment, carelessness or error on the part of the operator can result in
serious injury. If the operator violate any of these rules, you may cause serious injury to yourself
or others.
• Never pull the mower toward you while you are
walking. If you must back the mower away from a
wall or obstruction first look down and behind, and
then follow these steps:
1. GENERAL OPERATION
• Read this owner’s guide carefully in its entirety
before attempting to assemble this machine. Read,
understand, and follow all instructions on the
machine and in the manual(s) before operation. Be
completely familiar with the controls and the proper
use of this machine before operating it. Keep this
manual in a safe place for future and regular
reference and for ordering replacement parts.
• Your rotary mower is a precision piece of power
equipment, not a plaything. Therefore, exercise
extreme caution at all times. Your unit has been
designed to perform one job: to mow grass. Do not
use it for any other purpose.
• Never allow children under 14 years old to operate
a power mower. Children 14 years old and over
should only operate mower under close parental
supervision. Only responsible individuals who are
familiar with these rules of safe operation should be
allowed to use your mower.
• Keep the area of operation clear of all persons,
particularly small children and pets. Stop engine
when they are in the vicinity of your mower to help
prevent blade contact or thrown object injury.
Although the area of operation should be
completely cleared of foreign objects, an object
may have been overlooked and could be
accidentally thrown by the mower in any direction
and cause serious personal injury to the operator or
any others allowed in the area.
• Thoroughly inspect the area where the equipment
is to be used. Remove all stones, sticks, wire,
bones, toys and other foreign objects which could
be picked up and thrown by the mower in any
direction and cause serious personal injury to the
operator or any others allowed in the area. Plan
your mowing pattern to avoid discharge of material
toward roads, sidewalks, bystanders and the like.
• Step back from the mower to fully extend your
arms.
• Be sure you are well balanced with sure footing.
• Pull the mower back slowly, no more than half way
toward you.
• Repeat these steps as needed.
• Do not operate the mower while under the
influence of alcohol or drugs.
• The blade control handle is a safety device. Never
attempt to bypass its operation. Doing so makes
the safety device inoperative and may result in
personal injury through contact with the rotating
blade. The blade control handle must operate
easily in both directions and automatically return to
the disengaged position when released.
• Never operate the mower in wet grass. Always be
sure of your footing. A slip and fall can cause
serious personal injury. Keep a firm hold on the
handle and walk, never run. Mow only in daylight or
in good artificial light.
• Stop the blade when crossing gravel drives, walks
or roads.
• If the equipment should start to vibrate abnormally,
stop the engine and check immediately for the
cause. Vibration is generally a warning of trouble.
• Shut the engine off and wait until the blade comes
to a complete stop before removing the grass
catcher or unclogging the chute. The cutting blade
continues to rotate for a few seconds after the
engine is shut off. Never place any part of the body
in the blade area until you are sure the blade has
stopped rotating.
• Never operate mower without proper guards, grass
catcher, plates or other safety protective devices in
place.
• Muffler and engine become hot and can cause a
burn. Do not touch.
To help avoid
a
thrown objects injury, keep
children, bystanders and helpers at least 75 feet
from the mower while it is in operation.
• Only use accessories approved for this machine by
the manufacturer. Read, understand, and follow all
instructions provided with the approved accessory.
• If situations occur which are not covered in this
manual, use care and good judgment. Contact your
dealer for assistance.
• Always wear safety glasses or safety goggles
during operation or while performing an adjustment
or repair, to protect eyes from foreign objects that
may be thrown from the machine in any direction.
• Wear sturdy, rough-soled work shoes and close-
fitting slacks and shirts. Shirts and pants that cover
the arms and legs and steel-toed shoes are
recommended. Do not wear loose fitting clothes or
jewelry. They can be caught in moving parts. Never
operate a unit in bare feet, sandals, or sneakers.
• Do not put hands or feet near or under rotating
parts. Keep clear of discharge opening at all times
as the rotating blade can cause injury.
• Do not adjust the throttle control with the engine
running.
2. SLOPE OPERATION
For your safety, use the slope gauge included as part of this
manual to measure slopes before operating this unit on a
sloped or hilly area. If the slope is greater than 15 degrees
as shown on the slope gauge, do not operate this unit.
• Many injuries occur as a result of the mower being
pulled over the foot during a fall. Do not hang on to
the mower if you are falling; release the handle
immediately.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
DO:
• Check the blade and engine mounting bolts at
frequent intervals for proper tightness. Also,
visually inspect blade for damage (e.g., bent,
cracked). Replace with blade which meets original
equipment specifications.
• Mow across the face of slopes; never up and down.
Exercise extreme caution when changing direction
on slopes.
• Watch for holes, ruts, hidden objects, or bumps.
Tall grass can hide obstacles.
• Keep all nuts, bolts, and screws tight to be sure the
equipment is in safe working condition.
• Always be sure of your footing. A slip and fall can
cause serious personal injury. If you feel you are
losing your balance release the blade control
handle immediately and the blade will stop in less
than 3 seconds.
• ON MODELS WITH CASTER WHEELS: Lock both
front wheels so they do not pivot while mowing on
the face of slopes. To turn the mower, depress the
handle and raise the front wheels slightly.
• Never tamper with safety devices. Check their
proper operation regularly.
• After striking a foreign object, stop the engine,
remove the wire from the spark plug, and
thoroughly inspect the mower for any damage.
Repair the damage before starting and operating
the mower.
• Never attempt to make a wheel or cutting height
adjustment while the engine is running.
DO NOT:
• Grass catcher components are subject to wear,
damage and deterioration, which could expose
moving parts or allow objects to be thrown. For
safety protection, frequently check components and
replace with manufacturer’s recommended parts,
when necessary.
• Do not mow near drop-offs, ditches or
embankments. The operator could lose footing or
balance.
• Do not mow slopes greater than 15 degrees as
shown on the slope gauge.
• Do not mow on wet grass. Reduced footing could
cause slipping.
• Mower blades are sharp and can cut. Wrap the
blade(s) or wear gloves, and use extra caution
when servicing them.
• Do not change the engine governor setting or
overspeed the engine. Excessive engine speeds
are dangerous.
• ON MOWERS WITH CASTER WHEELS: Do Not
mow on slopes with casters unlocked since the
mower has a tendency to drift down hill.
3. CHILDREN
Your Responsibility
Tragic accidents can occur if the operator is not alert to the
presence of children. Children are often attracted to the
mower and the mowing activity. Never assume that children
will remain where you last saw them.
• Restrict the use of this power machine to persons
who read, understand and follow the warnings and
instructions in this manual and on the machine.
• Following are representations of the safety labels
on your lawn mower. Maintain safety while
operating the mower.
• Keep children out of the mowing area and under
the watchful care of a responsible adult other than
the operator.
• Be alert and turn mower off if a child enters the
area.
• Before and while moving backwards, look behind
and down for small children.
• Never allow children under age 14 to operate the
mower.
• Use extreme care when approaching blind corners,
shrubs, trees, or other objects that may obscure
your vision of a child or hazard.
4. SERVICE
• Use extreme care in handling gasoline and other
fuels. They are extremely flammable and the
vapors are explosive.
• Use only an approved gasoline container.
• Never remove gas cap or add fuel while the engine
is running. Allow engine to cool at least two
minutes before refueling.
• Replace gasoline cap securely and wipe off any
spilled gasoline before starting the engine as it may
cause a fire or explosion.
• Extinguish all cigarettes, cigars, pipes and other
sources of ignition.
• Never refuel machine indoors because flammable
vapors will accumulate in the area.
• Never store the machine or fuel container inside
where there is an open flame or spark such as a
gas water heater, space heater, or furnace.
• Never run an engine inside a closed area.
• To reduce fire hazard, keep mower free of grass,
leaves, or other debris build-up. Clean up oil or fuel
spillage. Allow mower to cool at least 5 minutes
before storing.
• Before cleaning, repairing, or inspecting, make
certain the blade and all moving parts have
stopped. Disconnect the spark plug wire, and keep
the wire away from the spark plug to prevent
accidental starting.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4: SLOPE GAUGE
USE THIS PAGE AS A GUIDE TO DETERMINE SLOPES WHERE YOU MAY NOT OPERATE SAFELY.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5: UNPACKING
Removing Unit From Carton
•
Remove staples, break glue on top flaps, or cut tape at carton end and peel along top flap to open
carton.
•
Remove loose parts if included with unit (i.e., Operator’s manual, etc.). See Figure 2.
FIGURE 2
•
•
Cut along dotted lines and lay carton down flat. Remove packing material.
Roll or slide unit out of carton. Check carton thoroughly for loose parts. See Figure 2.
NOTE: Make sure not to crimp the cable while removing the loose parts or the entire unit from the carton.
NOTE:Reference to right or left hand side of the mower and/or front or behind the mower is observed from
the operating position.
SECTION 6: SETTING UP MOWER
Tools Required
• Pair of Pliers
• Funnel
Disconnecting Spark Plug
• Before setting up your lawn mower, disconnect the spark plug wire from the spark plug, and ground
it against the engine. See Figure 3.
• Attach rubber boot to a bolt on the engine to ground.
Rubber Boot
Spark Plug
Wire
Spark Plug
FIGURE 3
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembling Handle
• Raise the lower handle in the direction shown in Figure 4A till it snaps into place.
Note: Make sure to route the cable inside the lower handle. Also do not crimp the cable while lifting the
handle up.
For shipping purposes, the hairpin clip is placed in the outer hole of the weld pin on the lower handle.
• Remove the hairpin clip from the outer hole of the weld pin.
• Using a pair of pliers, insert the hairpin clip into the inner hole in the weld pin. Repeat on other side.
See Figure 4 inset.
• Raise the upper handle in the direction shown in Figure 4B. Tighten the wing nuts which are
already on the handle.
• Attach the cable to the lower handle with the two cable ties already on the lower handle. Pull tight
on the cable ties and cut off the extra.
Hairpin
Clip
A
B
Lower
Handle
Weld
Pin
FIGURE 4
Attaching Starter Rope
The rope guide is already attached to the right side of the upper handle of your mower. See Figure 5.
• With the spark plug wire disconnected and grounded, hold the blade control handle against the
upper handle, and pull the starter rope out of the engine.
• Slip the rope through the rope guide. Tighten the wing nut holding the rope guide to the upper
handle.
Recoil
Starter
Wing Nut
Upper Handle
Rope Guide
Lower Handle
FIGURE 5
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Attaching Discharge Chute
Your lawn mower was shipped as a mulcher. Remove the mulching cover and attach the side-discharge chute for
discharging grass clippings.
• Remove three plastic wing nuts holding the mulching cover to the deck. See Figure 6A. Keep the cover in a
safe place for future use. Save the wing nuts.
• Place the side-discharge chute on the deck (in place of the mulching cover) so that the top flange on the
discharge chute goes under the top edge of the opening on the deck. See Figure 6B.
• Align the three slots on the chute with the hardware slots on the deck.
• Secure with the wing nuts earlier removed. Tighten the wing nuts.
A
B
Mulching
Cover
Side-Discharge
Chute
Top Flange
goes under
Align the slot
here (only two
shown)
top edge of
opening on deck
FIGURE 6
IMPORTANT: This unit is shipped WITHOUT GASOLINE or OIL. Be certain to service engine with gasoline and oil
as instructed in the separate engine manual before operating your mower.
SECTION 7: CONTROLS
Read this operator’s manual and safety rules before operating your lawn mower. Compare the illustrations in Figure 7
with your lawn mower to familiarize yourself with the location of various controls and adjustments. Save this manual for
future reference.
The operation of any lawn mower can result in foreign objects being thrown into the operator’s eyes thus causing
severe eye damage. Always wear safety glasses while operating the mower, or while performing any adjustments or
repairs on it.
Blade Control Handle
Oil Fill
Gas Tank
Plug
Recoil Starter
Engine
Caster Lock
Throttle
Control
Primer
Mulching
Cover
Spark Plug
FIGURE 7
9
Discharge
Chute
Download from Www.Somanuals.com. All Manuals Search And Download.
Recoil Starter
The recoil starter is attached to the handle. Stand behind the unit and pull the recoil starter to start the unit.
Primer
The primer is used to pump gas into the carburetor. Use it to start a cold engine, but do not use it to restart a
warm engine after short shutdown.
Blade Control Handle
WARNING: This control mechanism is a safety device. Never attempt to bypass its
operations.
The blade control handle is located on the upper handle of the mower. The blade control handle must be
depressed in order to operate the unit. Release the blade control handle to stop the engine and the blade.
Throttle Control
The throttle control is located on the engine. It is used to regulate the engine speed.
WARNING: The throttle control cannot be used to stop the engine. Do not adjust the
throttle control with the engine running.
Caster Wheels
Your mower is equipped with caster wheels in front. The casters can be locked in a straight ahead position for
mowing on hills, or can be left unlocked to swivel freely on level ground.
SECTION 8: OPERATION
Gas And Oil Fill-up
Oil :
• Only use high quality detergent oil rated with API service classification SF, SG or SH. Use SAE30 oil; do
not use 10W40 oil.
• Fill oil sump and check the oil level following steps below. See Figure 8.
a. Position the mower on level ground and clean area around oil fill plug.
b. Remove oil fill plug and dipstick. Wipe dipstick clean, insert it into oil fill hole and tighten securely.
c. Remove dipstick and check oil level. If the oil is not upto FULL mark on the dipstick, pour recommended
oil through the oil fill and check the level again.
• Install oil fill plug and dipstick, tighten securely.
Fill oil here
Fill gas here
FIGURE 8
NOTE: Although multi-viscosity oils (5W30, 10W30, etc.) improve starting in cold weather, these multiviscosity
oils will result in increased oil consumption when used above 32oF. Check the oil level more frequently to avoid
possible engine damage from running low on oil.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Gasoline
WARNING: Never fill fuel tank indoors, or when engine is running or hot. Do not smoke when filling
fuel tank.
• Clean area around fuel cap. Remove cap. See Figure 8. Use a funnel to prevent spillage.
• Pour approximately 1.5 quarts of fresh, regular grade, unleaded gasoline slowly to the fuel tank.
IMPORTANT: Never mix engine oil with gasoline.
• Fill tank to 1/2” below the bottom of the filler neck. Wipe any fuel spillage. Do not fill fuel tank completely.
Provide space for fuel expansion.
Starting Engine
WARNING: Be sure no one other than the operator is standing near the lawn mower while
starting or operating.
Never run engine indoors or in enclosed, poorly ventilated areas. Engine exhaust contains carbon
monoxide, an odorless and deadly gas.
Keep hands, feet, hair and loose clothing away from any moving parts on engine and lawn mower.
• To prevent the unit from sliding, place your foot firmly against the tire.
• Attach spark plug wire to spark plug. Make certain the metal cap on the end of the spark plug wire is fastened
securely over the metal tip on the spark plug.
• Move throttle control on the engine to the fast (rabbit) position.
• Push primer three times. Wait about two seconds between each push. In cold weather around 55o F or
below, prime five times. Do not prime to restart a warm engine after a short shutdown.
• Grasp starter handle and pull rope out slowly until engine reaches the start of compression cycle (rope will
pull slightly harder at this point). Let the rope rewind slowly.
• Pull rope with a rapid, continuous, full arm stroke. Keeping a firm grip on the starter handle, let the rope return
to the starter slowly.
Stopping Engine
• Release blade control handle to stop the engine and the blade.
• Disconnect spark plug wire and move away from spark plug to prevent accidental starting.
Locking Casters
If you are cutting grass on a slope, always lock the front wheel casters of your mower for straight ahead operation.
On level ground you may leave the casters unlocked to pivot freely.
To turn the mower on a slope with casters locked, depress the handle and raise the front wheels slightly.
• To lock caster: Lift and place the lock pin in the larger hole on each caster. See Figure 9.
• To unlock caster: Lift and place the lock pin in the smaller hole to allow casters to rotate freely.
Unlocked
Locked
Position
Position
FIGURE 9
11
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING: Do not mow on slopes with casters unlocked since the mower can drift downhill.
Using Your Lawn Mower
Your mower is designed to operate as a mulching or a side-discharge unit.
• For converting from a mulcher to a side-discharge unit, refer to instructions on page 9 of this manual.
• For converting from a side-discharge unit to a mulcher, replace the side-discharge chute with the mulching
cover. Do not operate the mower without the mulching cover or the discharge chute properly installed
and tightly secured.
• Be sure that the lawn is clear of stones, sticks, wire, or other objects which could damage lawn mower or
engine. Such objects could be accidently thrown by the mower in any direction and cause serious personal
injury to the operator and others.
• For best results, do not cut wet grass because it tends to stick to the underside of the mower, preventing
proper discharge of grass clippings, and could cause you to slip and fall. New grass, thick grass or wet grass
may require a narrower cut. Blade speed should be adjusted to the condition of the lawn.
• The best mowing pattern is one that allows the clippings to discharge towards the uncut part of the lawn. This
permits recutting of the clippings to further pulverize them. When cutting high weeds, discharge towards cut
portion, then recut at right angles to first direction.
• For a healthy lawn, always cut off one-third or less of the total length of the grass. Lawn should be trimmed in
fall as long as there is growth.
• This mower is designed to run at full throttle to give you the best cut and do the most effective job of bagging
the cut grass.
WARNING: If you strike a foreign object, stop the engine. Remove spark plug wire from spark
plug, thoroughly inspect the mower for any damage. Repair the damage before restarting and
operating the mower. Extensive vibration of the mower during operation is an indication of
damage. The unit should be promptly inspected and repaired.
Height Adjustment
Refer to height adjustments section of this manual on page 15 for instruction on how to adjust the cutting height and
the handle height.
• For best results in mowing, keep the cutting height position high until it is determined which height is best for
your lawn.
SECTION 9: MAINTENANCE
WARNING: Always stop the engine and disconnect the spark plug wire before performing any
maintenance or adjustments.
Cleaning Mower
The underside of the mower deck should be cleaned after each use to prevent any build-up of grass clippings,
leaves, dirt, or other debris. If this debris is allowed to accumulate, it will result in rust and corrosion.
• Disconnect spark plug wire.
• Drain the gasoline from the lawn mower, or place a piece of plastic under the gas cap.
• Tip the mower so that it rests on the housing. Keep the side with the air cleaner facing up. Hold the mower
firmly.
• Scrape clean the underside of the deck with a suitable tool.
• Put the mower back on its wheels on the ground. If you had put plastic under the gas cap, make sure to
remove it now.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING: Never tip the mower more than 90 degrees and do not leave the mower tipped for any
length of time. Oil can drain into the upper part of the engine causing a starting problem.
Engine Maintenance
• A list of key maintenance jobs required for good performance by the mower over the years follows here.
Follow the accompanying engine manual for detailed list and instructions.
• Change engine oil after the first two operating hours and every 25 operating hours thereafter. Check the oil
level before starting the engine every time.
• Service the foam filter in the air cleaner every 25 hours of use and replace the paper filter component every
100 hours. You may have to service the air filter more frequently if you are operating the mower under
extremely dusty conditions.
• Clean the engine periodically. Remove dirt and debris with a cloth or brush. We do not recommend using a
garden hose to clean mower unless the muffler, air filter and the carburetor are covered to keep water out.
Water in engine can shorten engine life.
• Clean the spark plug and reset the gap to .030” at least once a season or every 50 hours of operation. Spark
plug replacement is recommended at the start of each season. Refer to the engine manual, shipped with this
unit, for correct spark plug type.
• Inspect muffler periodically, and replace if necessary. Damaged mufflers or spark arresters can create a fire
hazard. Make sure to avoid muffler and surrounding areas while the mower engine is hot because
temperature of these areas of the engine may exceed 150o F.
Lubrication
For complete lubrication chart, see Figure 10.
Wheels
• Lubricate the wheels at least once a season with light oil or engine oil. Also, if the wheels are removed for
any reason, lubricate the surface of the axle bolt and the inner surface of the wheel with light oil.
Caster Assembly
• Grease fittings are provided for easy lubrication of the swivel pins located on the front caster assembly. Use a
grease gun to lubricate the casters every 25 operating hours or so.
Blade Control Handle
• Lubricate the pivot points on the blade control handle and the brake cable at least once a season with light
oil. The blade control handle must operate freely in both directions.
FIGURE 10
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 10: SERVICE & ADJUSTMENTS
Blade Care
Periodically inspect the blade adapter for cracks, especially if you strike a foreign object. Replace when necessary.
WARNING: When removing the cutting blade for sharpening or replacement, protect hands by
using heavy gloves or a rag to grasp the cutting blade.
• Disconnect spark plug wire from spark plug.
• Turn mower on its side making sure that the air filter and the carburetor are up.
To Remove Blade
• Remove the bolt and blade bell support which hold the blade and adapter to the engine crankshaft. See
Figure 11A.
• Remove the blade and adapter from the crankshaft.
To Replace Blade:
• Before reinstalling the blade and the blade adapter to the unit, lubricate the engine crankshaft and the inner
surface of the blade adapter with light oil.
• Install the blade adapter on the crankshaft with the “star” away from the engine. See Figure 11A.
1. Insert screw driver through hole
B
A
Blade Adapter
Crankshaft
Single-Bolt
Blade
2. Blade should be parallel to ground
Screw
Driver
Blade
Blade Bell
Support
Hex Bolt
Ground
FIGURE 11
• Place the new blade with the side marked bottom (or with part number) facing away from the adapter.
• Place the bell support next. Make sure to align the tabs in the holes of the blade with the hole in the bell
support.
• Insert the hex bolt through the blade assembly. Figure 11A shows the correct order of assembly.
• Use block of wood to hold blade again while you tighten the bolt clockwise. Follow the recommended torque
for the bolt which is 450-600 in.-lbs.
IMPORTANT: The bolt, used to secure the blade to the engine, is specially heat-treated. Do not substitute. To order
replacement bolt, refer to the Parts List section of this manual.
WARNING: To ensure safe operation of your unit, all nuts and bolts must be checked periodically
for correct tightness.
To Sharpen Blade:
• The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while blade is on
the mower.
• Follow the original angle of grind as a guide. Make sure that each cutting edge receives an equal amount of
grinding to prevent an unbalanced blade.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: An unbalanced blade will cause excessive vibration when rotating at high speeds, may cause damage to the
mower and could break, causing personal injury.
• Test the blade by balancing it on a round shaft screwdriver or a blade balancer. See Figure 11B.
• If the blade is not balanced, remove metal from the heavy side until it balances evenly.
Adjusting Handle Height
Your mower is shipped with the handle in the higher height position. To lower the handle height, proceed as follows.
• Remove the starter rope from the rope guide.
• Remove the upper handle by removing the hand knobs and carriage bolts. Lay the upper handle out of the
way, being careful not to bend or kink the cables.
• Remove the hairpin clips from the weld pins on the handle brackets. Refer to Figure 4 inset. Press out on the
legs of the lower handle. Remove lower handle from the mower.
• Turn the lower handle around so the notch on the bottom of the lower handle is facing forward as shown in
Figure 12. Reassemble, placing the bottom holes in the handle over the weld pins in the handle mounting
bracket.
Notch
Lower
Handle
FIGURE 12
• Reassemble the upper handle to the lower handle.
• Place the hairpin clips in the inner holes in the weld pins and attach the starter rope as instructed in the
Assembly section.
Adjusting Cutting Height
IMPORTANT: All wheels must be placed in the same relative position. For rough or uneven lawns, move the height
adjustment lever to a higher position. This will help stop scalping of the grass.
Rear Wheel Adjustment
The rear wheel cutting height adjustment rod is located between the two rear hi-wheels.
• Squeeze the two adjustment rods together and pull towards the operator.
• Move rods upward or downward to any one of the six positions and reinsert. See Figure 13A.
• Make sure that the rear rod sits in the groove of the new height position.
B
A
Rear Rod
Spring Washer
Axle Bolt
Adjustment
Rod
Wing
Nut
Trail
Shield
FIGURE 13
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Wheel Adjustment
The front wheel cutting height is determined by placing the axle rod in one of the six height adjustment positions in
each caster assembly on the front wheels.
• To adjust, remove the wing nut from the axle bolt. See Figure 13B.
• Slide the axle bolt and spring washer from the assembly and select a cutting height.
• With the spring washer on the axle bolt, reinsert the axle bolt in the square hole desired, through the wheel
assembly. See Figure 13B.
• Secure with wing nut previously removed.
SECTION 11: OFF-SEASON STORAGE
Prepare your lawn mower for storage at the end of the season or if the unit will not be used for 30 days or more.
Store the mower in a clean, dry area.
Mower
• Clean underside of the mower following instructions in the Maintenance section of this manual.
• Inspect and replace/sharpen blade, if required. Refer to the Maintenance section of this manual for blade
care instructions.
• Lubricate mower following the lubrication chart in Figure 10 of this manual.
• You can fold your mower’s handle for convenient storage as shown in Figure 14.
a. Remove the starter rope from the rope guide.
b. Loosen the two hand knobs on the sides of the handle, and let the upper handle fold down to the rear.
c. Move the hairpin clips to the outer hole in the weld pins on the handle mounting brackets.
d. Spread the sides of the lower handle, and push it forward and down.
FIGURE 14
NOTE: When folding the handle for storage or transportation, be careful not to bend or kink the cable.
Engine
• Follow recommendations in the accompanying engine manual for off-season storage of the engine.
• Change oil if it has not been changed in the last three months. For instructions on how to change oil, refer to
the engine manual.
• Clean engine and remove any grass clippings, dirt, or chaff from the exterior of the engine.
• Remove any dirt or debris from cooling fins, air intake screen, levers, and linkage.
IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as
carburetor, fuel filter, fuel hose, or tank during storage. Also, experience indicates that alcohol blended fuels (called
gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during
storage. Acidic gas can damage the fuel system of an engine while in storage.
Other
• Do not store gasoline from one season to another.
• Replace your gasoline can if it starts to rust. Rust and/or dirt in the gasoline will cause problems. Store unit in
a clean, dry area. Do not store next to corrosive materials, such as fertilizer.
NOTE: If storing in an unventilated or metal storage shed, be certain to rustproof the equipment by coating with a
light oil or silicone.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 12: TROUBLE-SHOOTING GUIDE
PROBLEM
POSSIBLE CAUSE
CORRECTIVE ACTION
Engine fails to start
1. Blade control handle disengaged
2.Spark plug wire disconnected
3.Throttle control lever not in fast position
4.Fuel tank empty, or stale fuel
5.Blocked fuel line
1. Engage blade control handle.
2.Connect wire to spark plug.
3.Move throttle lever to fast position.
4.Fill tank with fresh, clean fuel.
5.Clean fuel line.
6.Faulty spark plug
7.Engine flooded
6.Clean, adjust gap or replace.
7.Crank engine with throttle in slow
position.
Engine runs erratic
Engine overheats
1. Spark plug wire loose
2.Blocked fuel line or stale fuel
1. Connect and tighten spark plug wire.
2.Cleanfuelline,filltankwithclean,fresh
gasoline.
3.Vent in gas cap plugged
4.Water or dirt in fuel system
5.Dirty air cleaner
3.Clear vent.
4.Drain fuel tank. Refill with fresh fuel.
5.Clean air cleaner. Refer to engine
manual.
1. Engine oil level low
2.Air flow restricted
1. Fill crankcase with proper oil.
2.Clean lawn mower engine.
Occasional skip
(hesitates) at high
speed
1. Spark plug gap too close
1. Adjust gap to .030 inches.
Idles poorly
1. Spark plug fouled, faulty, or gap too wide
1. Reset gap to .030 inches or replace
spark plug.
2.Dirty air cleaner
2.Clean air cleaner .
Excessive vibration
1. Cutting blade loose or unbalanced
1. Tighten blade and adapter, balance
blade.
2.Bent cutting blade
2.Replace blade.
3.Bent engine crankshaft
3.Contact your nearest White dealer
Mower will not
mulch grass
1. Engine speed too low
2.Wet grass
1. Move throttle lever to FAST position.
2.Wait until later to cut.
3.Excessively high grass
3.Mow once at a high cutting height, then
mow again at desired height. Make a
narrower cutting swath (1/2) width. Do
not cut off more than 1/3 of the total
length.
4.Dull blade
4.Sharpen or replace blade.
Uneven cut
1. Wheels not in same height position
1. Place all four wheels in same relative
height position.
2.Dull blade
2.Sharpen or replace blade.
For repairs beyond the minor adjustments listed above,
please contact your nearest White Outdoor Products dealer.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 13: PARTS LIST
8
7
6
11
12
10
13
4
Engine shown for
reference only
2
3
15
14
5
2
4
Ref.
No.
1
Part No.
714-0104
Code
Description
Hairpin Clip
Wing Nut
1.
720-0241
726-0240
736-0451
749-0907A
749-0438B
647-0004
720-0295
710-1205
720-0279
746-0883
710-1270
2.
Cable Tie
3.
Saddle Washer
Lower Handle
Upper Handle
Control Handle
Foam Grip
4.
5.
6.
7.
8.
Rope Guide
Handle Knob
Housing Control
9.
10.
11.
12.
Oval C-Sunk
Scr.
712-0324
Hex L-Nut 1/4-
20 Thd.
13.
746-0912
710-1174
Control Cable
Carriage Bolt
14.
15.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Handles for reference only
1
15
59
11
3
14
19
13
17
3
52
44
16
25
20
59
18
23
12
21
47
51
45
5
4
35
6
37
30
27
43
48
41
51
46
26
22
24
34
31
32
33
34
38
29
42
40
39
46
58
50
53
49
36
41
57 56
2
56
54
46
40
7
38
10
8
9
2
55
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Ref.
No.
Ref.
No.
Part No.
Code
Description
Part No.
Code
Description
Engine
710-0654A
710-0703
TT Screw 3/8 -16 x 1.00
—
30.
31.
1.
751B281451
Engine Shroud
Carriage Screw 1/4-20 x
.75
734-1857
736-0105
Wheel, Front Caster 7 X 2
2.
3.
712-0397
726-0233
736-0204
Wing Nut
Push Nut
Flat Washer
Deck 21”
Bell Washer .401 X .870 X
.063
32.
33.
34.
35.
736-0182
736-0272
738-0481
Spring Washer .50 I.D. x
1.0 O.D. x .022
4.
5.
6.
782-0049-
0662
Flat Washer .510 x 1.0 x
.060
682-9020A
682-9021A
682-9024
710-0260
N
N
Caster Assembly, RH
Caster Assembly, LH
Caster Bracket Assembly
36.
37.
38.
39.
Shoulder Screw
.500 x 2.62: 3/8 -16
748-0377C
736-0524A
710-1257
Blade Adapter
7.
8.
9.
Carriage Bolt 5/16-18 x
.62
Blade Bell Support
Hex Bolt 3/8 - 24 x 2.5 Gr.
8
711-1146
712-0397
712-3004A
714-0104
726-0214
732-0306
736-0232
Caster Axle .374 x 2.59
Wing Nut
40.
41.
42.
43.
44.
45.
46.
742-0741
647-0028
Blade 21”, Mulching
10.
11.
Flange Nut 5/16-18 Gr.5
Hairpin Clip
Hi-Wheel Height Adj.
Support
710-1348
712-3017
732-0845
732-0843
732-0844
736-0105
AB Screw 1/4-14 x .50
Hex Nut 3/8 -16
12.
13.
14.
15.
16.
17.
Push Cap
Compression Spring
Torsion Spring
Wave Washer .530 I.D. x
.780 O.D.
Torsion Spring, RH
Torsion Spring, LH
736-0264
736-0931
Flat Washer .330 I.D. x
.630 x .06
48.
49.
Bell Washer .401 x .870 x
.063
Fl.Wash. .203 I.D. x .403
x .040
738-0145
747-0971
Shoulder Screw .500 x
.840
18.
19.
737-3000
741-0685
747-0924
731-1832
731-1833
731-1887
710-0653
Lube Fitting
50.
51.
52.
53.
54.
55.
56.
Flange Bearing
Lock Pin, Front Wheel
Discharge Chute
Mulching Cover
Hubcap
Handle, Height
Adjustment
750-1090
782-0572
682-3054
682-3055
710-1348
725-0157
731-1901
732-0842
710-0134
Spacer .500 x 1.0 x .600
Height Adj. Bracket, RH
Handle Bracket Ass’y, RH
Handle Bracket Ass’y, LH
AB Screw 1/4-14
20.
21.
22.
23.
24.
25.
26.
27.
29.
Hex Screw, TT 1/4-20 x
.375
710-0969
731-1828
734-1861
HL Screw
57.
58.
59.
Cable Tie
Rear Baffle
Trail Shield
Hi-Wheel 14 X 2
Trail Shield Wire
Carriage Screw
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Your Notes
Comments
Date
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Comments
Date
22
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUFACTURER’S LIMITED WARRANTY FOR:
For TWO YEARS from the date of retail purchase
within the United States of America, its possessions
and territories, White Outdoor Products Company will,
at its option, repair or replace, for the original
purchaser, free of charge, any part or parts found to be
defective in material or workmanship. This warranty
covers units which have been operated and
maintained in accordance with the operating
instructions furnished with the unit, and which have not
been subject to misuse, abuse, neglect, accident,
improper maintenance or alteration.
UNITS EXPORTED OUT OF THE UNITED STATES:
White Outdoor Products Company does not extend
any warranty for products sold or exported outside of
the United States of America, its possessions and
territories, except those sold through White Outdoor
Products Company’s authorized channels of export
distribution.
OTHER WARRANTIES:
1. The engine or component parts thereof carry
separate warranties from their manufacturers.
Please refer to the applicable manufacturer’s
warranty on these items.
NORMAL WEAR PARTS or components thereof are
subject to separate terms as noted below in the “No
Fault Ninety Day Consumer Warranty” clause.
Commercial use is subject to the terms listed above,
and is covered for a period of 90 days from the date of
purchase.
2. Batteries are covered by a 90-day replacement
warranty.
3. Log splitter pumps, valves and cylinders or
component parts thereof are covered by a one
year warranty.
TWO YEAR CONSUMER WARRANTY ON NORMAL
WEAR PARTS WITH NINETY DAY NO FAULT
PROTECTION: All normal wear parts failures will be
covered on this product for a period of 90 days
regardless of cause. After 90 days, but within the two
year period, normal wear parts failures will be covered
if caused by defects in material or workmanship.
Normal wear parts are defined as belts, blades, blade
adapters, grass bags, rider deck wheels, seats, snow
thrower skid shoes, shave plates and tires.
4. All other warranties, express or implied, including
any implied warranty of merchantability or fitness
for a particular purpose, are hereby expressly
disclaimed in their entirety.
5. The provisions as set forth in this warranty provide
the sole and exclusive remedy of White Outdoor
Products Company’s obligations arising from the
sales of its products. White Outdoor Products
Company will not be liable for incidental or
consequential loss or damage.
HOW TO OBTAIN SERVICE: Warranty service is
available, with proof of purchase, through your local
authorized service dealer. To locate the dealer in your
area, please check the yellow pages or contact the
Customer Service Department of White Outdoor
Products Company, P O Box 361131, Cleveland, Ohio
44136-0019. Phone (330) 225-8883. The return of a
complete unit will not be accepted by the factory
unless prior written permission has been extended by
the Service Department of White Outdoor Products
Company.
HOW STATE LAW RELATES TO THIS WARRANTY:
This limited warranty gives you specific legal rights,
and you may also have other rights which vary from
state to state. Certain disclaimers are not allowed in
some states and therefore they may not apply to you
under all circumstances.
NOTE: This warranty does not cover set-up, routine
maintenance items such as lubricants, filters, blade
sharpening and tune-ups, or adjustments such as
brake adjustments. Nor does this warranty cover
normal deterioration of the exterior finish due to use or
exposure.
TRANSPORTATION
CHARGES:
Transportation
charges for the movement of any power equipment
unit or attachment are the responsibility of the
purchaser. Transportation charges for any parts
submitted for replacement under this warranty must be
paid by the purchaser unless such return is requested
by White Outdoor Products Company.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING: The Engine Exhaust from this product contains
chemicals known to the State of California to cause cancer,
birth defects or other reproductive harm.
Download from Www.Somanuals.com. All Manuals Search And Download.
|