Weed Eater Lawn Mower 403284 User Guide

IMPORTANT MANUAL

Do Not Throw Away

01533

OPERATOR'S MANUAL

WARNING:

Read this Manual and follow allWarnings and

SafetyInstructions. Failuretodosocanresult

in serious injury.

MODEL:

HD13538

LAWN TRACTOR

ALWAYS WEAR EYE PROTECTION DURING OPERATION

Visit our website: www.weedeater.com

403284 11.28.05 VB

Printed in U.S.A.

Download from Www.Somanuals.com. All Manuals Search And Download.

SAFETY RULES

Safe Operation Practices for Ride-On Mowers

GENERAL SERVICE

III. CHILDREN

•

Never operate machine in a closed are.

Keep all nuts and bolts tight to be sure the equipment

is in safe working condition.

Never tamper with safety devices. Check their proper

operation regularly.

Keep machine free of grass, leaves, or other debris

build-up. Clean oil or fuel spillage and remove any fuel-

soaked debris. Allow machine to cool before storing.

If you strike a foreign object, stop and inspect the

machine. Repair, if necessary, before restarting.

Nevermakeanyadjustmentsorrepairswiththeengine

running.

Check grass catcher components and the discharge

guard frequently and replace with manufacturer's rec-

ommended parts, when necessary.

Tragic accidents can occur if the operator is not alert to

the presence of children. Children are often attracted to

the machine and the mowing activity. Never assume that

children will remain where you last saw them.

•

Keepchildrenoutofthemowingareaandinthewatchful

care of a responsible adult other than the operator.

Be alert and turn machine off if a child enters the

area.

Before and while backing, look behind and down for

small children.

Nevercarrychildren,evenwiththebladesshutoff. They

may fall off and be seriously injured or interfere with

safemachineoperation.Childrenwhohavebeengiven

rides in the past may suddenly appear in the mowing

area for another ride and be run over or backed over

by the machine.

Never allow children to operate the machine.

Useextracarewhenapproachingblindcorners,shrubs,

trees, or other objects that may block your view of a

child.

•

Mower blades are sharp. Wrap the blade or wear

gloves, and use extra caution when servicing them.

Check brake operation frequently. Adjust and service

as required.

Maintain or replace safety and instruction labels, as

necessary.

•

IV.TOWING

•

Tow only with a machine that has a hitch designed for

towing. Do not attach towed equipment except at the

hitch point.

•

Follow the manufacturer's recommendation for weight

limits for towed equipment and towing on slopes.

Never allow children or others in or on towed equip-

ment.

On slopes, the weight of the towed equipment may

cause loss of traction and loss of control.

Travel slowly and allow extra distance to stop.

•

Be sure the area is clear of bystanders before operat-

ing. Stop machine if anyone enters the area.

Never carry passengers.

Do not mow in reverse unless absolutely necessary.

Always look down and behind before and while back-

ing.

•

V. SERVICE

SAFE HANDLING OF GASOLINE

•

Nevercarrychildren,evenwiththebladesshutoff. They

may fall off and be seriously injured or interfere with

safemachineoperation.Childrenwhohavebeengiven

rides in the past may suddenly appear in the mowing

area for another ride and be run over or backed over

by the machine.

Keepchildrenoutofthemowingareaandinthewatchful

care of a responsible adult other than the operator.

Be alert and turn machine off if a child enters the

area.

Before and while backing, look behind and down for

small children.

Mow up and down slopes (15° Max), not across.

Choose a low ground speed so that you will not have

to stop or shift while on the slope.

Avoid starting, stopping, or turning on a slope. If the

tires lose traction, disengage the blades and proceed

slowly straight down the slope.

To avoid personal injury or property damage, use extreme

care in handling gasoline.Gasoline is extremely ﬂammable

and the vapors are explosive.

•

Extinguish all cigarettes, cigars, pipes, and other

sources of ignition.

•

Use only approved gasoline container.

Never remove gas cap or add fuel with the engine run-

ning. Allow engine to cool before refueling.

Never fuel the machine indoors.

Never store the machine or fuel container where there

is an open ﬂame, spark, or pilot light such as on a water

heater or other appliances.

•

Never ﬁll containers inside a vehicle or on a truck or

trailer bed with plastic liner. Always place containers

on the ground away from your vehicle when ﬁlling.

Removegas-poweredequipmentfromthetruckortrailer

and refuel it on the ground. If this is not possible, then

refuel such equipment with a portable container, rather

than from a gasoline dispenser nozzle.

Keep the nozzle in contact with the rim of the fuel tank

orcontaineropeningatalltimesuntilfuelingiscomplete.

Do not use a nozzle lock-open device.

•

If machine stops while going uphill, disengage blades,

shift into reverse and back down slowly.

Do not turn on slopes unless necessary, and then, turn

slowly and gradually downhill, if possible.

•

If fuel is spilled on clothing, change clothing immedi-

ately.

Never overﬁll fuel tank. Replace gas cap and tighten

securely.

Download from Www.Somanuals.com. All Manuals Search And Download.

CONGRATULATIONS on your purchase of a new tractor.

Ithasbeendesigned,engineeredandmanufacturedtogive

you the best possible dependability and performance.

PRODUCT SPECIFICATIONS

Gasoline Capacity

and Type:

1.25 Gallons

Unleaded Regular

Shouldyouexperienceanyproblemyoucannoteasilyrem-

edy,pleasecontactyournearestauthorizedservicecenter/

department. We have competent, well-trained technicians

and the proper tools to service or repair this tractor.

Oil Type (API-SG-SL):

SAE 30 (above 32°F)

SAE 5W-30 (below 32°F)

Oil Capacity:

3.0 Pints

Please read and retain this manual. The instructions will

enable you to assemble and maintain your tractor properly.

Always observe the “SAFETY RULES”.

Spark Plug:

(Gap: .030")

Champion RC12YC

Ground Speed (MPH):

Forward:

1st

2nd

1.1

1.4

2.2

3.3

4.4

4.9

1.4

CUSTOMER RESPONSIBILITIES

3rd

•

Read and observe the safety rules.

4th

Follow a regular schedule in maintaining, caring for

and using your tractor.

5th

6th

•

Follow the instructions under“Maintenance”and“Stor-

age” sections of this owner’s manual.

Reverse:

Tire Pressure:

Charging System:

Battery:

Front:

Rear:

14 PSI

12 PSI

WARNING: This tractor is equipped with an internal com-

bustion engine and should not be used on or near any

unimprovedforest-covered,brush-coveredorgrass-covered

land unless the engine’s exhaust system is equipped with

a spark arrester meeting applicable local or state laws (if

any). If a spark arrester is used, it should be maintained

in effective working order by the operator.

3 Amps Battery

5 Amps Headlights

AMP/HR:

Min. CCA:

Case Size:

230

U1R

Blade Torque:

45-55 FT. LBS.

A spark arrester for the mufﬂer is available through your

nearest authorized service center/department.

TABLE OF CONTENTS

SAFETY RULES .........................................................2-3

PRODUCT SPECIFICATIONS....................................... 4

CUSTOMER RESPONSIBILITIES................................. 4

ASSEMBLY.................................................................6-8

OPERATION .............................................................9-14

MAINTENANCE SCHEDULE ...................................... 15

MAINTENANCE .....................................................15-18

SERVICE AND ADJUSTMENTS ............................19-23

STORAGE.................................................................... 24

TROUBLESHOOTING ............................................25-26

WARRANTY................................................................. 27

Download from Www.Somanuals.com. All Manuals Search And Download.

CONTENTS OF HARDWARE PACK

Steering Wheel

Seat

(1) Washer

17/32 x 1-3/16 x 12 Gauge

Steering

Boot

(1) Lock

Washer 1/2

Steering

Wheel

Insert

(1) Bolt

Steering

Wheel

Adapter

Key

Steering

Extension

Shaft

(1) Large Flat

Washer

(2) Keys

(1) Oil Drain Tube

Slope Sheet

(1) 5/16

Lock Washer

(1) Hex Bolt 5/16-18 x 4

Download from Www.Somanuals.com. All Manuals Search And Download.

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes.

To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use

the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

INSERT

A socket wrench set will make assembly easier. Standard

5/16 HEX BOLT

wrench sizes are listed.

5/16 LOCK

(1) 1/2" wrench

(1) 3/4" wrench

Pliers

Utility knife

Tire pressure gauge

WASHER

LARGE FLAT

WASHER

Whenrightorlefthandismentionedinthismanual,itmeans

when you are in the operating position (seated behind the

steering wheel).

STEERING

WHEEL

STEERING

BOOT

TO REMOVE TRACTOR FROM

CARTON

UNPACK CARTON

TABS

•

Remove all accessible loose parts and parts cartons

from carton.

Cut along dotted lines on all four panels of carton.

Remove end panels and lay side panels ﬂat.

Check for any additional loose parts or cartons and

remove.

ADAPTER

EXTENSION

SHAFT

LOWER

STEERING

SHAFT

BEFORE REMOVING TRACTOR FROM

SKID

TAB

SLOTS

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

FIG. 1

•

Slide extension shaft onto lower steering shaft.

•

Place tabs of steering boot over tab slots in dash and

push down to secure.

INSTALL SEAT (See Fig. 2)

Adjust seat before tightening adjustment bolt.

INSTALL STEERING WHEEL

•

Remove adjustment bolt, lock washer and ﬂat washer

securing seat to cardboard packing and set aside for

assembly of seat to tractor.

•

Position front wheels of the tractor so they are pointing

straight forward.

Remove steering wheel adapter from steering wheel

and slide adapter onto steering shaft extension.

Position steering wheel so cross bars are horizontal

(left to right) and slide inside boot and onto adapter.

Assemble large ﬂat washer, 5/16 lock washer, 5/16 hex

bolt and tighten securely.

Snap steering wheel insert into center of steering

wheel.

Remove protective materials from tractor hood and

grill.

•

Pivotseatupwardandremovefromthecardboardpack-

ing. Remove the cardboard packing and discard.

Place seat on seat pan so head of shoulder bolt is

positioned over large slotted hole in pan.

Push down on seat to engage shoulder bolt in slot and

pull seat towards rear of tractor.

Pivot seat and pan forward and assemble adjust-

ment bolt, lockwasher and ﬂat washer loosely. Do not

tighten

•

Lower seat into operating position and sit on seat.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN

SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO

ROLL OFF SKID.

Slide seat until a comfortable position is reached

which allows you to press clutch/brake pedal all the

way down.

•

Get off seat without moving its adjusted position.

Raise seat and tighten adjustment bolt securely.

Download from Www.Somanuals.com. All Manuals Search And Download.

ASSEMBLY

NOTE: You may now roll or drive your tractor off the skid.

Follow the appropriate instruction below to remove the

tractor from the skid.

SHOULDER

BOLT

SEAT

TO ROLL TRACTOR OFF SKID (See Op-

eration section for location and function of

controls)

•

Press lift lever plunger and raise attachment lift lever

to its highest position.

SEAT PAN

•

Release parking brake by depressing clutch/brake

pedal.

•

Place gearshift lever in neutral (N) position.

Roll tractor forward off skid.

Remove banding holding deﬂector shield up against

tractor.

TO DRIVE TRACTOR OFF SKID (See Op-

eration section for location and function of

controls)

WARNING: Before starting, read, understand and follow

all instructions in the Operation section of this manual. Be

sure tractor is in a well-ventilated area. Be sure the area in

front of tractor is clear of other people and objects.

FLAT WASHER

LOCK WASHER

02465

•

Be sure all the above assembly steps have been com-

pleted.

ADJUSTMENT

BOLT

•

Check engine oil level and ﬁll fuel tank with gasoline.

Sit on seat in operating position, depress clutch/brake

pedal and set the parking brake.

FIG. 2

•

Place gear shift lever in neutral (N) position.

Press lift lever plunger and raise attachment lift lever

to its highest position.

Starttheengine.Afterenginehasstarted,movethrottle

control to idle position.

Depress clutch/brake pedal into full “BRAKE” position

and hold. Move gearshift lever to 1st gear.

Slowly release clutch/brake pedal and slowly drive

tractor off skid.

Apply brake to stop tractor, set parking brake and place

gearshift lever in neutral position.

CHECK BATTERY (See Fig. 3)

•

Lift seat pan to raised position.

If this battery is put into service after month and year

indicated on label (label located between terminals)

charge battery for minimum of one hour at 6-10 amps.

(See "BATTERY" in MAINTENANCE section of this

manual for charging instructions).

•

SEAT PAN

Turn ignition key to “OFF” position.

LABEL

Continue with the instructions that follow.

TERMINAL

FIG. 3

Download from Www.Somanuals.com. All Manuals Search And Download.

ASSEMBLY

CHECK TIRE PRESSURE

The tires on your tractor were overinﬂated at the factory

for shipping purposes. Correct tire pressure is important

for best cutting performance.

✓CHECKLIST

BEFORE YOU OPERATE YOUR NEW TRACTOR, WE

WISHTO ASSURETHATYOU RECEIVETHE BEST PER-

FORMANCE AND SATISFACTION FROMTHIS QUALITY

PRODUCT.

•

Reduce tire pressure to PSI shown in “PRODUCT

SPECIFICATIONS” section of this manual.

PLEASE REVIEW THE FOLLOWING CHECKLIST:

✓

All assembly instructions have been completed.

CHECK DECK LEVELNESS

For best cutting results, mower housing should be properly

leveled. See“TOLEVELMOWERHOUSING”intheService

and Adjustments section of this manual.

No remaining loose parts in carton.

Battery is properly prepared and charged. (Minimum

1 hour at 6 amps).

✓

Seat is adjusted comfortably and tightened securely.

CHECK FOR PROPER POSITION OF ALL

BELTS

See the ﬁgures that are shown for replacing motion and

mower blade drive belts in the Service and Adjustments

section of this manual. Verify that the belts are routed

correctly.

All tires are properly inﬂated. (For shipping purposes,

the tires were overinﬂated at the factory).

✓

Be sure mower deck is properly leveled side-to-side/

front-to-rear for best cutting results. (Tires must be

properly inﬂated for leveling).

✓

Check mower and drive belts. Be sure they are routed

properly around pulleys and inside all belt keepers.

CHECK BRAKE SYSTEM

Afteryoulearnhowtooperateyourtractor,checktoseethat

the brake is properly adjusted. See “TO ADJUST BRAKE”

in the Service and Adjustments section of this manual.

Check wiring. See that all connections are still secure

and wires are properly clamped.

WHILE LEARNING HOW TO USEYOUR TRACTOR, PAY

EXTRA ATTENTION TO THE FOLLOWING IMPORTANT

ITEMS:

✓

Engine oil is at proper level.

✓

Fuel tank is ﬁlled with fresh, clean, regular unleaded

gasoline.

✓

Become familiar with all controls, their location and

function. Operate them before you start the engine.

✓

Be sure brake system is in safe operating condition.

Be sure Operator Presence System and Reverse Op-

eration System (ROS) are working properly (See the

Operation and Maintenance sections in this manual).

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATION

These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their mean-

ing.

FAST

SLOW

REVERSE

HIGH

LOW

NEUTRAL

CHOKE

IGNITION SWITCH

ENGINE START

ENGINE ON

PARKING BRAKE

REVERSE

OPERATION

SYSTEM (ROS)

PARKING BRAKE PARKING BRAKE

ENGINE OFF

LOCKED

UNLOCKED

LIGHTS ON

BATTERY

REVERSE

FUEL

FORWARD

MOWER HEIGHT

MOWER LIFT

ATTACHMENT

CLUTCH ENGAGED

ATTACHMENT

CLUTCH DISENGAGED

BRAKE/CLUTCH

PEDAL

SLOPE HAZARDS

KEEP AREA CLEAR

(SEE SAFETY RULES SECTION)

DANGER indicates a hazard which, if not avoided,

will result in death or serious injury.

DANGER, KEEP HANDS

AND FEET AWAY

WARNING indicates a hazard which, if not avoided,

could result in death or serious injury.

FREE WHEEL

(Automatic Models only)

CAUTION indicates a hazard which, if not avoided,

might result in minor or moderate injury.

CAUTION when used without the alert symbol,

indicates a situation that could result in damage

to the tractor and/or engine.

Failure to follow instructions

could result in serious injury or

death. The safety alert symbol

is used to identify safety inform-

ation about hazards which can

result in death, serious injury

and/or property damage.

HOT SURFACES indicates a hazard which,

if not avoided, could result in death, serious injury

and/or property damage.

FIRE indicates a hazard which, if not avoided,

could result in death, serious injury and/or

property damage.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATION

KNOWYOUR TRACTOR

READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATINGYOUR TRACTOR

Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments.

Save this manual for future reference.

ATTACHMENT

ROS "ON"

IGNITION

CLUTCH LEVER

POSITION

SWITCH

LIFT LEVER

PLUNGER

LIGHT SWITCH

ATTACHMENT

LIFT LEVER

THROTTLE/CHOKE

CONTROL

HEIGHT

ADJUSTMENT

INDICATOR

CLUTCH/BRAKE

PEDAL

PARKING

BRAKE

GEAR SHIFT

LEVER

02829

FIG. 4

Our tractors conform to the safety standards of the American National Standards Institute.

ATTACHMENT CLUTCH LEVER - Used to engage the

LIFT LEVER PLUNGER - Used to release attachment lift

mower blades, or other attachments mounted to your

tractor.

lever when changing its position.

LIGHT SWITCH - Turns the headlights on and off.

PARKING BRAKE - Locks clutch/brake pedal into the

brake position.

REVERSE OPERATION SYSTEM (ROS) “ON” POSI-

TION - Allows operation of mower deck or other powered

attachment while in reverse.

THROTTLE/CHOKE CONTROL - Used for starting and

controlling engine speed.

ATTACHMENT LIFT LEVER - Used to raise, lower, and

adjust the mower deck or other attachments mounted to

your tractor.

CLUTCH/BRAKEPEDAL-Usedfordeclutchingandbrak-

ing the tractor and starting the engine.

GEARSHIFT LEVER - Selects the speed and direction

of the tractor.

IGNITION SWITCH - Used for starting and stopping the

engine.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATION

The operation of any tractor can result in foreign objects thrown into the eyes, which can result

in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or

performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles

or standard safety glasses.

NOTE: Under certain conditions when tractor is standing

HOW TO USEYOUR TRACTOR

idlewiththeenginerunning, hotengineexhaustgasesmay

cause “browning” of grass. To eliminate this possibility, al-

ways stop engine when stopping tractor on grass areas.

TO SET PARKING BRAKE (See Fig. 5)

Your tractor is equipped with an operator presence sens-

ing switch. When engine is running, any attempt by the

operator to leave the seat without ﬁrst setting the parking

brake will shut off the engine.

CAUTION: Always stop tractor com-

pletely,asdescribedabove,beforeleav-

ing the operator's position; to empty

grass catcher, etc.

•

Depress clutch/brake pedal into full “BRAKE” position

and hold.

•

Place parking brake lever in“ENGAGED”position and

releasepressurefromclutch/brakepedal. Pedalshould

remain in “BRAKE” position. Make sure parking brake

will hold tractor secure.

TO USE THROTTLE CONTROL (See Fig. 5)

Always operate engine at full throttle.

•

Operating engine at less than full throttle reduces the

battery charging rate.

Full throttle offers the best bagging and mower perfor-

mance.

ATTACHMENT CLUTCH

LEVER "ENGAGED"

POSITION

TO MOVE FORWARD AND BACKWARD

(See Fig. 5)

The direction and speed of movement is controlled by the

gearshift lever.

IGNITION KEY

THROTTLE/

CHOKE

"DISENGAGED"

POSITION

CONTROL

LEVER

PARKING BRAKE

"ENGAGED"

POSITION

•

Start tractor with clutch/brake pedal depressed and

gearshift lever in neutral (N) position.

Move gearshift lever to desired position.

Slowly release clutch/brake pedal to start move-

ment.

"BRAKE"

POSITION

•

GEAR SHIFT

LEVER

IMPORTANT: BRING TRACTOR TO A COMPLETE STOP

BEFORE SHIFTING OR CHANGING GEARS. FAILURE

TO DO SO WILL SHORTEN THE USEFUL LIFE OF YOUR

TRANSAXLE.

CLUTCH/BRAKE

PEDAL "DRIVE"

POSITION

PARKING BRAKE

"DISENGAGED"

POSITION

FIG. 5

TO ADJUST MOWER CUTTING HEIGHT

(See Fig. 5)

The position of the attachment lift lever determines the

cutting height.

STOPPING (See Fig. 5)

MOWER BLADES -

•

To stop mower blades,move attachment clutch lever

to “DISENGAGED” position.

•

Grasp lift lever.

Press plunger with thumb and move lever to desired

position.

GROUND DRIVE -

•

To stop ground drive, depress clutch/brake pedal into

The cutting height range is approximately 1-1/2 to 4".

The heights are measured from the ground to the blade tip

withtheenginenotrunning. Theseheightsareapproximate

and may vary depending upon soil conditions, height of

grass and types of grass being mowed.

full “BRAKE” position.

•

Move gearshift lever to neutral (N) position.

ENGINE -

Move throttle control between half and full speed (fast)

position.

•

The average lawn should be cut to approximately 2-1/2

inches during the cool season and to over 3 inches

during hot months. For healthier and better looking

lawns, mow often and after moderate growth.

NOTE: Failure to move throttle control between half and

fullspeed(fast)position,beforestoppingmaycauseengine

to “backﬁ r e ” .

•

For best cutting performance, grass over 6 inches

in height should be mowed twice. Make the ﬁrst cut

relatively high; the second to desired height.

•

Turn ignition key to “OFF” position and remove key.

Always remove key when leaving tractor to prevent

unauthorized use.

•

Never use choke to stop engine.

IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY

POSITION OTHER THAN "OFF" WILL CAUSE THE BATTERY

TO BE DISCHARGED, (DEAD).

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATION

REVERSE OPERATION SYSTEM (ROS)

"ENGAGED" POSITION

Your tractor is equipped with a Reverse Operation System

(ROS). Any attempt by the operator to travel in the reverse

direction with the attachment clutch engaged will shut off

the engine unless ignition key is placed in the ROS "ON"

position.

ATTACHMENT

LIFT LEVER

HIGH POSITION

LOW

POSITION

WARNING: Backing up with the attachment clutch en-

gaged while mowing is strongly discouraged. Turning the

ROS "ON", to allow reverse operation with the attachment

clutch engaged, should only be done when the operator

decides it is necessary to reposition the machine with the

attachment engaged. Do not mow in reverse unless

absolutely necessary.

ATTACHMENT

CLUTCH LEVER

"DISENGAGED"

POSITION

USING THE REVERSE OPERATION SYSTEM -

•

Depress clutch/brake pedal all the way down and

hold.

DEFLECTOR

SHIELD

•

Withenginerunning,turnignitionkeycounterclockwise

to ROS "ON" position.

FIG. 6

•

Look down and behind before and while backing.

Move gear shift lever to reverse (R) position and slowly

release clutch/brake pedal to start movement.

TO OPERATE ON HILLS

•

When use of the ROS is no longer needed, turn the

ignition key clockwise to engine "ON" position.

WARNING: Do not drive up or down

hills with slopes greater than 15° and

do not drive across any slope.

ROS "ON" POSITION

ENGINE "ON" POSITION

(NORMAL OPERATING)

•

Choose the slowest speed before starting up or down

hills.

•

Avoid stopping or changing speed on hills.

If slowing is necessary, move throttle control lever to

slower position.

•

If stopping is absolutely necessary, push clutch/brake

pedal quickly to brake position and engage parking

brake.

Move gearshift lever to 1st gear. Be sure you have

allowed room for tractor to roll slightly as you restart

movement.

TO OPERATE MOWER (See Fig. 6)

Yourtractor isequippedwithanoperatorpresencesensing

switch. Any attempt by the operator to leave the seat with

the engine running and the attachment clutch engaged

will shut off the engine.You must remain fully and centrally

positioned in the seat to prevent the engine from hesitating

or cutting off when operating your equipment on rough,

rolling terrain or hills.

•

Torestartmovement, slowlyreleaseparkingbrakeand

clutch/brake pedal.

Make all turns slowly.

TO TRANSPORT

•

Raiseattachmentlifttohighestpositionwithattachment

lift control.

When pushing or towing your tractor, be sure gearshift

lever is in neutral (N) position.

•

Select desired height of cut.

Start mower blades by engaging attachment clutch

control.

Do not push or tow tractor at more than ﬁve (5) MPH.

•

TO STOP MOWER BLADES - disengage attachment

clutch control.

NOTE: To protect hood from damage when transporting

your tractor on a truck or a trailer, be sure hood is closed

and secured to tractor. Use an appropriate means of tying

hood to tractor (rope, cord, etc.).

CAUTION: Do not operate the mower

without either the entire grass catcher,

onmowerssoequipped,orthedeﬂector

shield in place.

TOWING CARTS AND OTHER ATTACH-

MENTS

Tow only the attachments that are recommended by and

comply with speciﬁcations of the manufacturer of your trac-

tor. Use common sense when towing.Too heavy of a load,

while on a slope, is dangerous.Tires can lose traction with

the ground and cause you to lose control of your tractor.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATION

TO START ENGINE (See Fig. 5)

When starting the engine for the ﬁrst time or if the engine

has run out of fuel, it will take extra cranking time to move

fuel from the tank to the engine.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

The engine in your tractor has been shipped, from the

factory, already ﬁlled with summer weight oil.

•

Sit on seat in operating position, depress clutch/brake

pedal and set parking brake.

•

Check engine oil with tractor on level ground.

•

Place gear shift lever in neutral (N) position.

Move attachment clutch to “DISENGAGED” position.

Move throttle control to choke ( ) position.

Remove oil ﬁll cap/dipstick and wipe clean, reinsert the

dipstick and screw cap tight, wait for a few seconds,

remove and read oil level. If necessary, add oil until

“FULL” mark on dipstick is reached. Do not overﬁll.

NOTE: Before starting, read the warm and cold starting

procedures below.

•

For cold weather operation you should change oil for

easier starting (See “OIL VISCOSITY CHART” in the

Maintenance section of this manual).

To change engine oil, see the Maintenance section in

this manual.

•

Insertkeyintoignitionandturnkeyclockwiseto“START”

position and release key as soon as engine starts.

Do not run starter continuously for more than ﬁfteen

seconds per minute. If the engine does not start after

several attempts, move throttle control to fast position,

wait a few minutes and try again. If engine still does

not start, move the throttle control back to the choke (

) position and retry.

ADD GASOLINE

•

Fill fuel tank to bottom of ﬁller neck. Do not overﬁll.

Use fresh, clean, regular unleaded gasoline with a

minimum of 87 octane. (Use of leaded gasoline will

increase carbon and lead oxide deposits and reduce

valve life). Do not mix oil with gasoline. Purchase fuel

in quantities that can be used within 30 days to assure

fuel freshness.

WARM WEATHER STARTING (50° F and above)

•

When engine starts, move the throttle control to the

fast position.

•

The attachments and ground drive can now be used. If

the engine does not accept the load, restart the engine

and allow it to warm up for one minute using the choke

as described above.

CAUTION: Wipe off any spilled oil or

fuel. Do not store, spill or use gasoline

near an open ﬂame.

COLD WEATHER STARTING ( 50° F and below)

•

Whenenginestarts,allowenginetorunwiththethrottle

control in the choke ( ) position until the engine runs

roughly, then move throttle control to fast position.This

may require an engine warm-up period from several

seconds to several minutes, depending on the tem-

perature.

IMPORTANT: WHEN OPERATING IN TEMPERATURES

BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE

GASOLINE TO HELP INSURE GOOD COLD WEATHER

STARTING.

CAUTION: Alcohol blended fuels (called

gasohol or using ethanol or methanol) can at-

tract moisture which leads to separation and

formation of acids during storage. Acidic gas

can damage the fuel system of an engine while

in storage. To avoid engine problems, the fuel

system should be emptied before storage of

30 days or longer. Drain the gas tank, start

the engine and let it run until the fuel lines

and carburetor are empty. Use fresh fuel next

season. SeeStorageInstructionsforadditional

information. Never use engine or carburetor

cleaner products in the fuel tank or permanent

damage may occur.

•

The attachments can also be used during the engine

warm-up period.

NOTE: If at a high altitude (above 3000 feet) or in cold

temperatures (below 32 F) the carburetor fuel mixture may

need to be adjusted for best engine performance. See “TO

ADJUST CARBURETOR” in the Service and Adjustments

section of this manual.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATION

MOWING TIPS

•

Mower should be properly leveled for best mowing per-

formance. See"TOLEVELMOWERHOUSING"inthe

Service and Adjustments section of this manual.

The left hand side of mower should be used for trim-

ming.

•

Drive so that clippings are discharged onto the area

that has been cut. Have the cut area to the right of the

machine. This will result in a more even distribution of

clippings and more uniform cutting.

•

Whenmowinglargeareas,startbyturningtotherightso

that clippings will discharge away from shrubs, fences,

driveways, etc. After one or two rounds, mow in the

opposite direction making left hand turns until ﬁnished

(See Fig. 7).

FIG. 7

•

If grass is extremely tall, it should be mowed twice to

reduce load and possible ﬁre hazard from dried clip-

pings. Make ﬁrst cut relatively high; the second to the

desired height.

•

Do not mow grass when it is wet. Wet grass will plug

mower and leave undesirable clumps. Allow grass to

dry before mowing.

Always operate engine at full throttle when mow-

ing to assure better mowing performance and proper

discharge of material. Regulate ground speed by se-

lecting a low enough gear to give the mower cutting

performance as well as the quality of cut desired.

When operating attachments, select a ground speed

that will suit the terrain and give best performance of

the attachment being used.

•

Download from Www.Somanuals.com. All Manuals Search And Download.

MAINTENANCE

BEFORE

EACH

USE

EVERY

HOURS

EVERY

HOURS

EVERY

HOURS

EVERY

100

HOURS

EVERY

SEASON

BEFORE

STORAGE

MAINTENANCE

SCHEDULE

Check Brake Operation

T ^{Check Tire Pressure}

R ^{Check Operator Presence & ROS Systems}

A ^{Check for Loose Fasteners}

Check/Replace Mower Blades

Lubrication Chart

Check Battery Level

Clean Battery and Terminals

Check Transaxle Cooling

Check Mower Levelness

Check V-Belts

Check Engine Oil Level

1,2

Change Engine Oil (with oil filter)

1,2

E ^{Change Engine Oil (without oil filter)}

N ^{Clean Air Filter}

G ^{Clean Air Screen}

Inspect Muffler/Spark Arrester

Replace Oil Filter (If equipped)

E _{Clean Engine Cooling Fins}

Replace Spark Plug

Replace Air Filter Paper Cartridge

Replace Fuel Filter

1 - Change more often when operating under a heavy load or

in high ambient temperatures.

3 - Replace blades more often when mowing in sandy soil.

4 - Not required if equipped with maintenance-free battery.

2 - Service more often when operating in dirty or dusty conditions.

LUBRICATION CHART

dSPINDLE ZERK

GENERAL RECOMMENDATIONS

dSPINDLE ZERK

The warranty on this tractor does not cover items that have

beensubjectedtooperatorabuseornegligence. Toreceive

full value from the warranty, operator must maintain tractor

as instructed in this manual.

dFRONT WHEEL

BEARING ZERK

Some adjustments will need to be made periodically to

properly maintain your tractor.

At least once a season, check to see if you should make

any of the adjustments described in the Service and

Adjustments section of this manual.

eENGINE

• At least once a year you should replace the spark plug,

clean or replace air ﬁlter, and check blades and belts

for wear. A new spark plug and clean air ﬁlter assure

proper air-fuel mixture and help your engine run better

and last longer.

cGEARSHIFT

PIVOTS

BEFORE EACH USE

cSAE 30 OR 10W30 MOTOR OIL

dGENERAL PURPOSE GREASE

eREFER TO MAINTENANCE “ENGINE” SECTION

•

Check engine oil level.

Check brake operation.

Check tire pressure.

Check operator presence and

ROS systems for proper operation.

Check for loose fasteners.

IMPORTANT: DO NOT OIL OR GREASE THE PIVOT POINTS WHICH

HAVE SPECIAL NYLON BEARINGS. VISCOUS LUBRICANTS WILL

ATTRACT DUST AND DIRT THAT WILL SHORTEN THE LIFE OF

THE SELF-LUBRICATING BEARINGS. IF YOU FEEL THEY MUST

BE LUBRICATED, USE ONLY A DRY, POWDERED GRAPHITE TYPE

LUBRICANT SPARINGLY.

•

Download from Www.Somanuals.com. All Manuals Search And Download.

MAINTENANCE

BLADE CARE

Forbestresultsmowerbladesmustbekeptsharp. Replace

bent or damaged blades.

TRACTOR

Always observe safety rules when performing any main-

tenance.

BRAKE OPERATION

CAUTION: Useonlyareplacementblade

approved by the manufacturer of your

tractor. Using a blade not approved

by the manufacturer of your tractor is

hazardous, could damage your tractor

and void your warranty.

If tractor requires more than ﬁve (5) feet to stop at highest

speed in highest gear on a level, dry concrete or paved

surface, then brake must be checked and adjusted. (See

“TO ADJUST BRAKE” in the Service and Adjustments

section of this manual).

TIRES

BLADE REMOVAL (See Fig. 8)

•

Maintainproperairpressureinalltires(See“PRODUCT

•

Raise mower to highest position to allow access to

blades.

SPECIFICATIONS” section of this manual).

Keep tires free of gasoline, oil, or insect control chemi-

cals which can harm rubber.

Avoid stumps, stones, deep ruts, sharp objects and

other hazards that may cause tire damage.

NOTE: Protect your hands with gloves and/or wrap blade

with heavy cloth.

•

Remove blade bolt by turning counterclockwise.

Install new or resharpened blade with stamped "THIS

SIDE UP" facing deck and mandrel assembly.

NOTE: To seal tire punctures and prevent ﬂat tires due to

slow leaks, tire sealant may be purchased from your local

parts dealer. Tire sealant also prevents tire dry rot and

corrosion.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER

HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL

ASSEMBLY.

OPERATOR PRESENCE SYSTEM AND REVERSE OP-

ERATION SYSTEM (ROS)

•

Install and tighten blade bolt securely (45-55 Ft. Lbs.

torque).

Be sure operator presence and reverse operation systems

are working properly. If your tractor does not function as

described, repair the problem immediately.

IMPORTANT: SPECIAL BLADE BOLT HEAT TREATED.

STAR

BLADE

•

The engine should not start unless the brake pedal is

fully depressed, and the attachment clutch control is

in the disengaged position.

CENTER

HOLE

BLADE BOLT

(SPECIAL)

CHECK OPERATOR PRESENCE SYSTEM

025

•

Whentheengineisrunning,anyattemptbytheoperator

to leave the seat without ﬁrst setting the parking brake

should shut off the engine.

When the engine is running and the attachment clutch

is engaged, any attempt by the operator to leave the

seat should shut off the engine.

MANDREL

ASSEMBLY

FIG. 8

The attachment clutch should never operate unless

the operator is in the seat.

TO SHARPEN BLADE (See Fig. 9)

NOTE: We do not recommend sharpening blade - but if

you do, be sure the blade is balanced.

CHECK REVERSE OPERATION (ROS) SYSTEM

•

When the engine is running with the ignition switch in

the engine "ON" position and the attachment clutch

engaged, any attempt by the operator to shift into

reverse should shut off the engine.

Care should be taken to keep the blade balanced. An un-

balancedbladewillcauseexcessivevibrationandeventual

damage to mower and engine.

•

When the engine is running with the ignition switch in

the ROS "ON" position and the attachment clutch en-

gaged, any attempt by the operator to shift into reverse

should NOT shut off the engine.

•

The blade can be sharpened with a ﬁle or on a grind-

ing wheel. Do not attempt to sharpen while on the

mower.

To check blade balance, you will need a 5/8" diameter

steel bolt, pin, or a cone balancer. (When using a

cone balancer, follow the instructions supplied with

balancer.)

•

ROS "ON" POSITION

ENGINE "ON" POSITION

(NORMAL OPERATING)

NOTE: Do not use a nail for balancing blade. The lobes of

the center hole may appear to be centered, but are not.

•

Slidebladeontoanunthreadedportionofthesteelbolt

or pin and hold the bolt or pin parallel with the ground.

If blade is balanced, it should remain in a horizontal

position. If either end of the blade moves downward,

sharpen the heavy end until the blade is balanced.

Download from Www.Somanuals.com. All Manuals Search And Download.

MAINTENANCE

SAE VISCOSITY GRADES

CENTER HOLE

SAE 30

5W-30

-20

32 40

100

-20

-30

-10

BLADE

5/8" BOLT

OR PIN

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

oil_visc_chart1_e

FIG. 10

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.)

improvestartingincoldweather,theywillresultinincreased

oilconsumptionwhenusedabove32°F. Checkyourengine

oil level more frequently to avoid possible engine damage

from running low on oil.

FIG. 9

Change the oil after every 25 hours of operation or at least

once a year if the tractor is not used for 25 hours in one

year.

Check the crankcase oil level before starting the engine

and after each eight (8) hours of operation. Tighten oil ﬁll

cap/dipstick securely each time you check the oil level.

BATTERY

Yourtractorhasabatterychargingsystemwhichissufﬁcient

for normal use. However, periodic charging of the battery

with an automotive charger will extend its life.

•

Keep battery and terminals clean.

Keep battery bolts tight.

Keep small vent holes open.

Recharge at 6-10 amperes for 1 hour.

TO CHANGE ENGINE OIL (See Figs. 10 and 11)

Determine temperature range expected before oil change.

All oil must meet API service classiﬁcation SG-SL.

NOTE: The original equipment battery on your tractor is

maintenance free. Do not attempt to open or remove caps

or covers. Adding or checking level of electrolyte is not

necessary.

•

Be sure tractor is on level surface.

Oil will drain more freely when warm.

Catch oil in a suitable container.

Remove oil ﬁll cap/dipstick. Be careful not to allow dirt

to enter the engine when changing oil.

Remove yellow cap from end of drain valve and install

the drain tube onto the ﬁtting.

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and terminals can cause

the battery to “leak” power.

•

Disconnect BLACK battery cable ﬁrst then RED bat-

tery cable and remove battery from tractor.

OIL DRAIN VALVE

•

Rinse the battery with plain water and dry.

Cleanterminalsandbatterycableendswithwirebrush

until bright.

Coat terminals with grease or petroleum jelly.

Reinstall battery (See “REPLACING BATTERY” in the

Service and Adjustment section of this manual).

CLOSED

AND

LOCKED

POSITION

•

DRAIN

YELLOW CAP

TUBE

V-BELTS

CheckV-beltsfordeteriorationandwearafter100hoursand

replace if necessary.The belts are not adjustable.Replace

belts if they begin to slip from wear.

FIG. 11

•

Unlock drain valve by pushing inward and turning

counterclockwise.

To open, pull out on the drain valve.

After oil has drained completely, close and lock the

drain valve by pushing inward and turning clockwise

until the pin is in the locked position as shown.

Remove the drain tube and replace the cap onto to the

bottom ﬁtting of the drain valve.

Reﬁll engine with oil through oil ﬁll dipstick tube. Pour

slowly. Do not overﬁll. For approximate capacity see

“PRODUCT SPECIFICATIONS” section of this manual.

Use gauge on oil ﬁll cap/dipstick for checking level.

For accurate reading, insert dipstick into the tube

and push down ﬁrmly into place before removing.

Keep oil up to, but not over, the “FULL” line on dip-

stick. Push dipstick down ﬁrmly into the tube when

ﬁnished.

TRANSAXLE COOLING

Keep transaxle free from build-up of dirt and chaff which

can restrict cooling.

•

ENGINE

•

LUBRICATION

Only use high quality detergent oil rated with API service

classiﬁcation SG-SL. Select the oil’s SAE viscosity grade

according to your expected operating temperature.

•

Download from Www.Somanuals.com. All Manuals Search And Download.

MAINTENANCE

CLEAN AIR SCREEN

IN-LINE FUEL FILTER (See Fig. 12)

The fuel ﬁlter should be replaced once each season. If fuel

ﬁlter becomes clogged, obstructing fuel ﬂow to carburetor,

replacement is required.

Air screen must be kept free of dirt and chaff to prevent

engine damage from overheating. Clean with a wire brush

or compressed air to remove dirt and stubborn dried gum

ﬁbers.

•

With engine cool, remove ﬁlter and plug fuel line sec-

tions.

Place new fuel ﬁlter in position in fuel line with arrow

pointing towards carburetor.

Be sure there are no fuel line leaks and clamps are

properly positioned.

Immediately wipe up any spilled gasoline.

AIR FILTER

Your engine will not run properly using a dirty air ﬁlter.

Service air cleaner more often under dusty conditions.See

Engine Manual.

MUFFLER

Inspect and replace corroded mufﬂer and spark arrester

(if equipped) as it could create a ﬁre hazard and/or dam-

age.

CLAMP

SPARK PLUGS

Replace spark plugs at the beginning of each mowing sea-

son or after every 100 hours of use, whichever comes ﬁrst.

Spark plug type and gap setting is shown in "PRODUCT

SPECIFICATIONS" section of this manual.

FUEL

FILTER

FIG. 12

CLEANING

•

Clean engine, battery, seat, ﬁnish, etc. of all foreign

matter.

Keep ﬁnished surfaces and wheels free of all gasoline,

oil, etc.

Protect painted surfaces with automotive type wax.

We do not recommend using a garden hose or pressure

washer to clean your tractor unless the engine and trans-

mission are covered to keep water out. Water in engine or

transmission will shorten the useful life of your tractor. Use

compressed air or a leaf blower to remove grass, leaves

and trash from tractor and mower.

Download from Www.Somanuals.com. All Manuals Search And Download.

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUST-

MENTS:

•

Depress clutch/brake pedal fully and set parking brake.

Place gearshift lever in neutral (N) position.

Place attachment clutch in “DISENGAGED” position.

Turn ignition key to “STOP” and remove key.

Make sure the blades and all moving parts have completely stopped.

Disconnect spark plug wire from spark plug and place wire where it cannot come in contact

with plug.

TRACTOR

TO INSTALL MOWER (See Fig. 13)

TO REMOVE MOWER (See Fig. 13)

•

Raise attachment lift lever to its highest position.

Mower will be easier to remove from the right side of trac-

tor.

Slide mower under tractor with deﬂector shield to right

side of tractor.

•

Place attachment clutch in “DISENGAGED” position.

Move attachment lift lever forward to lower mower to

its lowest position.

•

Lower lift lever to its lowest position.

Connect front links to mower deck and secure with

retainer springs..

•

Roll belt off engine pulley.

Removesmallretainerspring,andremoveclutchspring

off pulley bolt.

Remove large retainer spring, slide collar off and push

housing guide out of bracket.

Disconnect anti-swaybar from chassis bracket by re-

moving retainer spring.

Disconnect suspension arms from rear deck brackets

by removing retainer springs.

Disconnect front links from deck by removing retainer

springs.

Raise lift lever to raise suspension arms. Slide mower

out from under tractor.

•

Connect suspension arms to rear deck brackets and

secure with retainer springs.

Connect anti-swaybar to chassis bracket and secure

with retainer spring.

Push clutch cable housing guide into bracket, slide col-

lar onto guide and secure with large retainer spring.

Place ﬂat washer and clutch spring on idler pulley bolt

and secure with small retainer spring.

•

Make sure belt is inside the belt keeper at the idler and

on both sides of the wire belt keeper as shown.

Install belt onto engine pulley.

IMPORTANT: CHECK BELT FOR PROPER ROUTING IN ALL

MOWER PULLEY GROOVES.

IMPORTANT:IFANATTACHMENTOTHERTHANTHEMOWER

DECK IS TO BE MOUNTED ON THE TRACTOR, REMOVE

THE FRONT LINKS AND HOOK THE CLUTCH SPRING INTO

SQUARE HOLE IN FRAME.

SMALL RETAINER SPRING

FLAT WASHER

WIRE BELT KEEPER

SUSPENSION ARMS

CLUTCH SPRING

BELT KEEPER

SQUARE HOLE

RETAINER SPRING

ANTI-SWAY BAR

ENGINE PULLEY

FRONT LINK

COLLAR

HOUSING GUIDE

RETAINER SPRINGS

(BOTH SIDES)

02845

LARGE

RETAINER

SPRING

BRACKET

DEFLECTOR SHIELD

CLUTCH SPRING

FIG. 13

Download from Www.Somanuals.com. All Manuals Search And Download.

SERVICE AND ADJUSTMENTS

•

When distance “D” is 1/8" to 1/2" lower at front than

rear, tighten nuts “F” against trunnion on both front

links.

To raise front of mower, loosen nut“F”from trunnion on

both front links. Tighten nut “E” on both front links an

equal number of turns.The two front links must remain

equal in length.

Whendistance“D”is1/8"to1/2"loweratfrontthanrear,

tighten nut “F” against trunnion on both front links.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground

or driveway. Make sure tires are properly inﬂated (See

“PRODUCT SPECIFICATIONS”section of this manual). If

tires are over or underinﬂated, you will not properly adjust

your mower.

•

SIDE-TO-SIDE ADJUSTMENT (See Figs. 14 and 15)

•

Raise mower to its highest position.

•

At the midpoint of both sides of mower, measure height

from bottom edge of mower to ground. Distance “A”

on both sides of mower should be the same or within

1/4" of each other.

Recheck side-to-side adjustment.

MANDREL

•

If adjustment is necessary, make adjustment on one

side of mower only.

To raise one side of mower, tighten lift link adjustment

nut on that side.

To lower one side of mower, loosen lift link adjustment

nut on that side.

“D”

FIG. 16

NOTE: Each full turn of adjustment nut will change mower

height about 1/8".

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

•

Recheck measurements after adjusting.

BOTTOM EDGE

OF MOWER TO

GROUND

BOTTOM EDGE

OF MOWER TO

GROUND

NUT “F”

NUT “E”

GROUND LINE

FIG. 14

TRUNNION

SUSPENSION ARM

FRONT LINKS

LIFT LINK

ADJUSTMENT NUT

FIG. 17

TO REPLACE MOWER BLADE DRIVE BELT

(See Fig. 18)

The mower blade drive belt may be replaced without tools.

Park the tractor on level surface. Engage parking brake.

FIG. 15

FRONT-TO-BACK ADJUSTMENT (See Figs. 16 and 17)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE

FOLLOWINGFRONT-TO-BACKADJUSTMENTISNECESSARY,

BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO

MOWER WILL STAY LEVEL SIDE-TO-SIDE.

BELT REMOVAL -

•

Place attachment clutch in “DISENGAGED” position.

Move attachment lift lever forward to lower mower to

its lowest position.

To obtain the best cutting results, the mower housing

should be adjusted so that the front is approximately 1/8"

to 1/2" lower than the rear when the mower is in its high-

est position.

•

Roll belt off engine pulley.

Work belt off both mandrel pulleys and idler pulleys.

Pull belt away from mower.

Checkadjustmentonrightsideoftractor. Measuredistance

“D” directly in front and behind the mandrel at bottom edge

of mower housing as shown.

BELT INSTALLATION -

•

Work new belt around both mandrel pulleys and idler

pulleys.

•

Before making any necessary adjustments, check that

both front links are equal in length.

If links are not equal in length, adjust one link to same

length as other link.

To lower front of mower loosen nut “E” on both front

links an equal number of turns.

•

Install new belt into engine pulley groove.

Make sure belt is inside the belt keeper at the idler and

on both sides of the wire belt keeper as shown.

IMPORTANT: CHECK BELT FOR PROPER ROUTING IN ALL

MOWER PULLEY GROOVES.

Download from Www.Somanuals.com. All Manuals Search And Download.

SERVICE AND ADJUSTMENTS

WIRE BELT KEEPER

TO REPLACE MOTION DRIVE BELT

BELT KEEPER

(See Fig. 20)

MANDREL

PULLEY

Park the tractor on level surface. Engage parking brake.

For assistance, there is a belt installation guide decal on

bottom side of left footrest.

BELT REMOVAL -

•

Remove mower (See “TO REMOVE MOWER” in this

section of manual).

ENGINE

PULLEY

NOTE: Observe entire motion drive belt and position of all

belt guides and keepers.

IDLER

PULLEYS

•

Remove belt from stationary idler and clutching idler.

Remove belt downward from around engine pulley.

Pull belt slack toward rear of tractor. Remove belt

upwards from transaxle pulley by deﬂecting belt keep-

ers.

MANDREL

PULLEY

02844

FIG. 18

•

Remove belt from center span keeper and pull belt

away from tractor.

TO CHECK AND ADJUST BRAKE

(See Fig. 19)

Your tractor is equipped with an adjustable brake system

which is mounted on the right side of the transaxle.

BELT INSTALLATION -

•

Carefully work new belt down between transaxle belt

keepers and onto the input pulley.

Slide belt into the center span keeper.

Pull belt toward front of tractor and roll around the top

groove of engine pulley.

Install belt through stationary idler and clutching

idler.

Make sure belt is in all pulley grooves and inside all

belt guides and keepers.

Install mower (See “TO INSTALL MOWER” in this sec-

tion of manual).

If tractor requires more than ﬁve (5) feet to stop at highest

speed in highest gear on a level, dry concrete or paved

surface, then brake must be checked and adjusted.

•

TO CHECK BRAKE

•

Park tractor on a level, dry concrete or paved surface,

depress clutch/brake pedal all the way down and en-

gage parking brake.

•

Place gear shift lever in neutral (N) position.

Therearwheelsmustlockandskidwhenyoutrytomanually

push the tractor forward.If the rear wheels rotate, the brake

needs to be adjusted or the pads need to be replaced.

ENGINE

PULLEY

TO ADJUST BRAKE

•

Depress clutch/brake pedal all the way down and en-

CLUTCHING

IDLER

gage parking brake.

Measure distance between brake operating arm and

nut “A” on brake rod.

If distance is other than 1-1/2", loosen jam nut and turn

nut “A” until distance becomes 1-1/2". Retighten jam

nut against nut “A”.

STATIONARY

IDLER

CENTER SPAN

KEEPER

•

Roadtesttractorforproperstoppingdistanceasstated

above. Readjust if necessary. If stopping distance is

still greater than ﬁve (5) feet in highest gear, further

maintenance is necessary. Replace brake pads or

contact a qualiﬁed service center.

TRANSAXLE

PULLEY

WITH PARKING BRAKE “ENGAGED”

1-1/2"

NUT “A”

FIG. 20

JAM NUT

OPERATING ARM

FIG. 19

Download from Www.Somanuals.com. All Manuals Search And Download.

SERVICE AND ADJUSTMENTS

TRANSAXLE GEAR SHIFT LEVER NEUTRAL-

ADJUSTMENT (See Fig. 21)

WASHERS

RETAINING

RING

The transaxle should be in neutral when the gear shift

lever is in neutral (N) (lock gate) position. The adjustment

is preset at the factory; however, if adjustment is needed,

proceed as follows:

AXLE

COVER

•

Make sure transaxle is in neutral (N).

NOTE: When the tractor rear wheels move freely, the

transaxle is in neutral.

Loosen adjustment bolt in front of the right rear

wheel.

SQUARE KEY (REAR

WHEEL ONLY)

•

FIG. 22

Position the gear shift lever in the neutral (N) posi-

tion.

TO START ENGINE WITH A WEAK BATTERY

(See Fig. 23)

Tighten adjustment bolt securely.

NOTE: Ifadditionalclearanceisneededtogettoadjustment

bolt, move mower deck height to the lowest position.

WARNING: Lead-acid batteries gen-

erate explosive gases. Keep sparks,

ﬂameandsmokingmaterialsawayfrom

batteries. Always wear eye protection

when around batteries.

NEUTRAL

LOCK GATE

GEARSHIFT LEVER

If your battery is too weak to start the engine, it should be

recharged. (See "BATTERY" in the Maintenance section

of this manual).

If “jumper cables” are used for emergency starting, follow

this procedure:

IMPORTANT: YOURTRACTOR IS EQUIPPEDWITH A 12VOLT

SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT

SYSTEM. DO NOT USEYOUR TRACTOR BATTERY TO START

OTHER VEHICLES.

ADJUSTMENT

BOLT

FIG. 21

TO ATTACH JUMPER CABLES -

TO ADJUST STEERING WHEEL ALIGN-

MENT

If steering wheel crossbars are not horizontal (left to right)

whenwheelsarepositionedstraightforward,removesteer-

ing wheel and reassemble per instructions in the Assembly

section of this manual.

•

Connect one end of the RED cable to the POSITIVE

(+) terminal of each battery(A-B), taking care not to

short against tractor chassis.

•

ConnectoneendoftheBLACKcabletotheNEGATIVE

(-) terminal (C) of fully charged battery.

Connect the other end of the BLACK cable (D) to good

chassis ground, away from fuel tank and battery.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on

yourtractor.Ifdamagehasoccurredtoaffectthefrontwheel

toe-in or camber, contact your nearest authorized service

center/department.

TO REMOVE CABLES, REVERSE ORDER -

•

BLACK cable ﬁrst from chassis and then from the fully

charged battery.

•

RED cable last from both batteries.

TO REMOVE WHEEL FOR REPAIRS

(See Fig. 22)

•

Block up axle securely.

Removeaxlecover, retainingringandwasherstoallow

wheel removal (rear wheel contains a square key - Do

not lose).

•

Repair tire and reassemble.

On rear wheels only: align grooves in rear wheel hub

and axle. Insert square key.

•

Replace washers and snap retaining ring securely in

axle groove.

Replace axle cover.

WEAK OR DEAD

BATTERY

FULLY CHARGED

BATTERY

FIG. 23

NOTE: To seal tire punctures and prevent ﬂat tires due to

slow leaks, tire sealant may be purchased from your local

parts dealer. Tire sealant also prevents tire dry rot and

corrosion.

Download from Www.Somanuals.com. All Manuals Search And Download.

SERVICE AND ADJUSTMENTS

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The

fuse holder is located behind the dash.

REPLACING BATTERY (See Figs. 24 and 25)

WARNING: Do not short battery

terminals by allowing a wrench or any

other object to contact both terminals

at the same time. Before connect-

ing battery, remove metal bracelets,

wristwatch bands, rings, etc.

Positive terminal must be connected

ﬁrst to prevent sparking from acci-

dental grounding.

TO REMOVE HOOD AND GRILL ASSEMBLY

(See Fig. 26)

•

Raise hood.

Unsnap headlight wire connector.

Stand in front of tractor. Grasp hood at sides, tilt toward

engine and lift off of tractor.

•

To replace, reverse above procedure.

•

Lift seat pan to raised position.

DisconnectBLACKbatterycableﬁrstthenREDbattery

cable and carefully remove battery from tractor.

HOOD

•

Install new battery with terminals in same position as

old battery.

First connect RED battery cable to positive (+) terminal

with hex bolt and keps nut as shown.Tighten securely.

Slide terminal cover over terminal.

HEADLIGHT WIRE

CONNECTOR

•

Connect BLACK grounding cable to negative (-) ter-

minal with remaining hex bolt and keps nut. Tighten

securely.

01536

SEAT PAN

FIG. 26

ENGINE

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and

adjustment should not be necessary. If adjustment is nec-

essary, see engine manual.

FIG. 24

TERMINAL

COVER

KEPS NUT

TO ADJUST CHOKE CONTROL

The choke control has been preset at the factory and ad-

justment should not be necessary. If adjustment is neces-

sary, see engne manual.

HEX

BOLT

TO ADJUST CARBURETOR

Your carburetor is not adjustable. If your engine does not

operate properly due to suspected carburetor problems,

take your tractor to an authorized service center for repair

and/or adjustment.

POSITIVE (RED) CABLE

NEGATIVE (BLACK) CABLE

FIG. 25

TO REPLACE HEADLIGHT BULB

•

Raise hood.

Pull bulb holder out of the hole in the backside of the

grill.

•

Replace bulb in holder and push bulb holder securely

back into the hole in the backside of the grill.

Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run

poorly, stop running, or prevent it from starting.

•

Check wiring. See electrical wiring diagram in the

Repair Parts section.

Download from Www.Somanuals.com. All Manuals Search And Download.

STORAGE

Immediately prepare your tractor for storage at the end

of the season or if the tractor will not be used for 30 days

or more.

ENGINE

FUEL SYSTEM

IMPORTANT: ITISIMPORTANTTOPREVENTGUMDEPOSITS

FROMFORMINGIN ESSENTIALFUELSYSTEMPARTSSUCH

AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK

DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT

ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING

ETHANOLORMETHANOL)CANATTRACTMOISTUREWHICH

LEADSTOSEPARATIONANDFORMATIONOFACIDSDURING

STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM

OF AN ENGINE WHILE IN STORAGE.

WARNING: Never store the tractor with

gasoline in the tank inside a building

where fumes may reach an open ﬂame

orspark. Allowtheenginetocoolbefore

storing in any enclosure.

TRACTOR

•

Empty the fuel tank by starting the engine and let it run

until the fuel lines and carburetor are empty.

Never use engine or carburetor cleaner products in the

fuel tank or permanent damage may occur.

Removemowerfromtractorforwinterstorage. Whenmower

istobestoredforaperiodoftime,cleanitthoroughly,remove

all dirt, grease, leaves, etc. Store in a clean, dry area.

•

Clean entire tractor (See “CLEANING” in the Mainte-

nance section of this manual).

Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in mini-

mizing the formation of fuel gum deposits during storage.

Add stabilizer to gasoline in fuel tank or storage container.

Always follow the mix ratio found on stabilizer container.

Run engine at least 10 minutes after adding stabilizer to

allow the stabilizer to reach the carburetor. Do not empty

the gas tank and carburetor if using fuel stabilizer.

•

Inspect and replace belts, if necessary (See belt re-

placement instructions in the Service and Adjustments

section of this manual).

•

Lubricate as shown in the Maintenance section of this

manual.

Be sure that all nuts, bolts and screws are securely

fastened. Inspect moving parts for damage, breakage

and wear. Replace if necessary.

ENGINE OIL

•

Touch up all rusted or chipped paint surfaces; sand

lightly before painting.

Drain oil (with engine warm) and replace with clean en-

gine oil. (See “ENGINE” in the Maintenance section of

this manual).

BATTERY

CYLINDER(S)

•

Fully charge the battery for storage.

•

Remove spark plug(s).

After a period of time in storage, battery may require

recharging.

Pour one ounce of oil through spark plug hole(s) into

cylinder(s).

•

To help prevent corrosion and power leakage during

long periods of storage, battery cables should be dis-

connected and battery cleaned thoroughly (see “TO

CLEAN BATTERY AND TERMINALS” in the Mainte-

nance section of this manual).

•

Turn ignition key to “START”position for a few seconds

to distribute oil.

Replace with new spark plug(s).

•

After cleaning, leave cables disconnected and place

cables where they cannot come in contact with battery

terminals.

If battery is removed from tractor for storage, do not

store battery directly on concrete or damp surfaces.

OTHER

•

Do not store gasoline from one season to another.

Replace your gasoline can if your can starts to rust.

Rust and/or dirt in your gasoline will cause problems.

•

If possible, store your tractor indoors and cover it to

give protection from dust and dirt.

Cover your tractor with a suitable protective cover that

does not retain moisture. Do not use plastic. Plastic

cannot breathe which allows condensation to form and

will cause your tractor to rust.

IMPORTANT: NEVERCOVERTRACTORWHILEENGINE AND

EXHAUST AREAS ARE STILL WARM.

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING POINTS

PROBLEM

CAUSE

CORRECTION

Will not start

1. Out of fuel.

1. Fill fuel tank.

2. Engine not “CHOKED” properly.

3. Engine ﬂooded.

4. Bad spark plug.

5. Dirty air ﬁlter.

2. See “TO START ENGINE” in Operation section.

3. Wait several minutes before attempting to start.

4. Replace spark plug.

5. Clean/replace air ﬁlter.

6. Dirty fuel ﬁlter.

6. Replace fuel ﬁlter.

7. Water in fuel.

7. Empty fuel tank and carburetor, reﬁll tank with fresh

gasoline and replace fuel ﬁlter.

8. Loose or damaged wiring.

8. Check all wiring.

9. Carburetor out of adjustment.

9. See “To Adjust Carburetor” in Service Adjustments

section.

10. Engine valves out of adjustment.

10. Contact an authorized service center/department.

Hard to start

1. Dirty air ﬁlter.

1. Clean/replace air ﬁlter.

2. Bad spark plug.

2. Replace spark plug.

3. Weak or dead battery.

4. Dirty fuel ﬁlter.

3. Recharge or replace battery.

4. Replace fuel ﬁlter.

5. Stale or dirty fuel.

6. Loose or damaged wiring.

7. Carburetor out of adjustment.

5. Empty fuel tank and reﬁll tank with fresh, clean gasoline.

6. Check all wiring.

7. See “To Adjust Carburetor” in Service Adjustments

section.

8. Engine valves out of adjustment.

8. Contact an authorized service center/department.

Engine will not turn over

1. Clutch/brake pedal not depressed.

2. Attachment clutch is engaged.

3. Weak or dead battery.

1. Depress clutch/brake pedal.

2. Disengage attachment clutch.

3. Recharge or replace battery.

4. Replace fuse.

4. Blown fuse.

5. Corroded battery terminals.

6. Loose or damaged wiring.

7. Faulty ignition switch.

8. Faulty solenoid or starter.

9. Faulty operator presence switch(es).

5. Clean battery terminals.

6. Check all wiring.

7. Check/replace ignition switch.

8. Check/replace solenoid or starter.

9. Contact an authorized service center/department.

Engine clicks but will not

start

1. Weak or dead battery.

1. Recharge or replace battery.

2. Clean battery terminals.

3. Check all wiring.

2. Corroded battery terminals.

3. Loose or damaged wiring.

4. Faulty solenoid or starter.

4. Check/replace solenoid or starter.

Loss of power

1. Cutting too much grass/too fast.

2. Throttle in “CHOKE” position.

3. Build-up of grass, leaves and trash under mower.

4. Dirty air ﬁlter.

1. Raise cutting height/reduce speed.

2. Adjust throttle control.

3. Clean underside of mower housing.

4. Clean/replace air ﬁlter.

5. Low oil level/dirty oil.

6. Faulty spark plug.

7. Dirty fuel ﬁlter.

5. Check oil level/change oil.

6. Clean and regap or change spark plug.

7. Replace fuel ﬁlter.

8. Stale or dirty fuel.

9. Water in fuel.

8. Empty fuel tank and reﬁll tank with fresh, clean gasoline.

9. Empty fuel tank and carburetor, reﬁll tank with fresh

gasoline and replace fuel ﬁlter.

10. Spark plug wire loose.

11. Dirty engine air screen/ﬁns.

12. Dirty/clogged mufﬂer.

10. Connect and tighten spark plug wire.

11. Clean engine air screen/ﬁns.

12. Clean/replace mufﬂer.

13. Loose or damaged wiring.

14. Carburetor out of adjustment.

13. Check all wiring.

14. See “To Adjust Carburetor” in Service Adjustments

section.

15. Engine valves out of adjustment.

15. Contact an authorized service center/department.

Excessive vibration

1. Worn, bent or loose blade.

2. Bent blade mandrel.

1. Replace blade. Tighten blade bolt.

2. Replace blade mandrel.

3. Loose/damaged part(s).

3. Tighten loose part(s). Replace damaged parts.

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING POINTS

PROBLEM

CAUSE

CORRECTION

Engine dies when

tractor is shifted

into reverse

1. Reverse operation system

(ROS) is not "ON" while

1. Turn ignition key to

ROS "ON" position.

mower or other attachment

is engaged.

See Operation section.

Engine continues to run

when operator leaves seat

with attachment clutch

engaged

1. Faulty operator-safety presence control system.

1. Check wiring, switches and connections. If not

corrected, contact an authorized service center/

department.

Poor cut - uneven

1. Worn, bent or loose blade.

2. Mower deck not level.

1. Replace blade. Tighten blade bolt.

2. Level mower deck.

3. Buildup of grass, leaves, and trash under mower.

4. Bent blade mandrel.

3. Clean underside of mower housing.

4. Replace blade mandrel.

5. Clogged mower deck vent holes from buildup of

grass, leaves, and trash around mandrels.

5. Clean around mandrels to open vent holes.

Mower blades will not

rotate

1. Obstruction in clutch mechanism.

2. Worn/damaged mower drive belt.

3. Frozen idler pulley.

1. Remove obstruction.

2. Replace mower drive belt.

3. Replace idler pulley.

4. Frozen blade mandrel.

4. Replace blade mandrel.

Poor grass discharge

1. Engine speed too slow.

2. Travel speed too fast.

1. Place throttle control in “FAST” position.

2. Shift to slower speed.

3. Wet grass.

4. Mower deck not level.

3. Allow grass to dry before mowing.

4. Level mower deck.

5. Low/uneven tire air pressure.

6. Worn, bent or loose blade.

7. Buildup of grass, leaves and trash under mower.

8. Mower drive belt worn.

5. Check tires for proper air pressure.

6. Replace/sharpen blade. Tighten blade bolt.

7. Clean underside of mower housing.

8. Replace mower drive belt.

9. Blades improperly installed.

10. Improper blades used.

11. Clogged mower deck vent holes from buildup of

grass, leaves, and trash around mandrels.

9. Reinstall blades sharp edge down.

10. Replace with blades listed in this manual.

11. Clean around mandrels to open vent holes.

Headlight(s) not working

(if so equipped)

1. Light switch is “OFF”.

2. Bulb(s) or lamp(s) burned out.

3. Faulty light switch.

4. Loose or damaged wiring.

5. Blown fuse.

1. Turn light switch “ON”.

2. Replace bulb(s) or lamp(s).

3. Check/replace light switch.

4. Check wiring and connections.

5. Replace fuse.

Battery will not charge

1. Bad battery cell(s).

1. Replace battery.

2. Poor cable connections.

3. Faulty regulator (if so equipped).

4. Faulty alternator.

2. Check/clean all connections.

3. Replace regulator.

4. Replace alternator.

Engine “backﬁres” when

turning engine “OFF”

1. Engine throttle control not set between half and

full speed (fast) position before stopping engine.

1. Move throttle control between half and full speed

(fast) position before stopping engine.

Download from Www.Somanuals.com. All Manuals Search And Download.

LIMITED WARRANTY

The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materi-

als and workmanship. For a period of two (2) years from date of purchase by the original consumer purchaser, we will repair or

replace, at our option, without charge for parts or labor incurred in replacing parts, any part which we ﬁnd to be defective due

to materials or workmanship. This Warranty is subject to the following limitations and exclusions.

1. This warranty does not apply to the engine, other than EHP manufactured transaxle/transmission components, battery (ex-

cept as noted below) or components parts thereof. Please refer to the applicable manufacturer's warranty on these items.

2. Transportation charges for the movement of any power equipment unit or attachment are the responsibility of the pur-

chaser. Transportation charges for any parts submitted for replacement under this warranty must be paid by the purchaser

unless such return is requested by Electrolux Home Products.

3. Battery Warranty: On products equipped with a Battery, we will replace, without charge to you, any battery which we ﬁnd

to be defective in manufacture, during the ﬁrst ninety (90) days of ownership. After ninety (90) days, we will exchange the

Battery, charging you 1/12 of the price of a new Battery for each full month from the date of the original sale. Battery must

be maintained in accordance with the instructions furnished.

4. The Warranty period for any products used for rental or commercial purposes is limited to 90 days from the date of original

purchase.

5. This Warranty applies only to products which have been properly assembled, adjusted, operated, and maintained in accor-

dance with the instructions furnished. This Warranty does not apply to any product which has been subjected to alteration,

misuse, abuse, improper assembly or installation, delivery damage, or to normal wear of the product.

6. Exclusions: Excluded from this Warranty are belts, blades, blade adapters, normal wear, normal adjustments, standard

hardware and normal maintenance.

7. In the event you have a claim under this Warranty, you must return the product to an authorized service dealer.

Should you have any unanswered questions concerning this Warranty, please contact:

In Canada contact:

Electrolux Home Products, Inc.

Electrolux Canada Corp.

7075 Ordan Drive

Mississauga, Ontario

L5T 1K6

Outdoor Products Customer Service Dept.

1030 Stevens Creek Road

Augusta, GA 30907 USA

giving the model number, serial number and date of purchase of your product and the name and address of the authorized

dealer from whom it was purchased.

THIS WARRANTY DOES NOT APPLY TO INCIDENTAL OR CONSEQUENTIAL DAMAGES AND ANY IMPLIED WARRAN-

TIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN FOR OUR EXPRESSED WARRANTIES. Some areas

do not allow the limitation of consequential damages or limitations of how long an implied Warranty may last, so the above limi-

tations or exclusions may not apply to you. This Warranty gives you speciﬁc legal rights, and you may have other rights which

vary from locale to locale.

This is a limited Warranty within the meaning of that term as deﬁned in the Magnuson-Moss Act of 1975.

Download from Www.Somanuals.com. All Manuals Search And Download.

SERVICE

POLICY

WARRANTY

Issued January 1980

Revised January 1991

LIMITED WARRANTIES

FOR

NEW PEERLESS GEAR POWER TRAIN COMPONENTS

A. Products Warranted

Peerless Gear and Machine Division of Tecumseh Products Company (“Tecumseh”), subject to the limitations contained below,

will, at its option, repair or replace, without charge for parts or labor only, any part of a new Power Train Component (which as used

herein means and includes the transaxle, gear box, transmission, differential and right angle drives, and any part of the Power Train

Component), EXCEPT any new Power Train Component incorporated in equipment used for commercial or rental purposes, which is

found upon examination by any Tecumseh Authorized Service Outlet or by Tecumseh’s factory in Grafton, Wisconsin, to be DEFECTIVE

IN MATERIAL AND/OR WORKMANSHIP if received by Tecumseh or a Tecumseh Authorized Service Outlet for such examination within

TWO YEARS from the date of sale to the original consumer purchaser of Peerless Series 820, 900, 910, 915, 920, 930 transaxles and

Series 1100 angle drive and ONEYEAR for all other Peerless products. New PowerTrain Components incorporated in equipment used for

commercial purposes are warranted in the same manner and to the same extent EXCEPT such Power Train Components are warranted

for NINETY (90) DAYS ONLY, and must be received by Tecumseh or by a Tecumseh Authorized Service Outlet for such examination

within 90 days from the date of sale to the original purchaser. New Power Train Components Incorporated in equipment used for rental

purposes are warranted in the same manner and to the same extent EXCEPT such Power Train Components are warranted for THIRTY

(30) DAYS ONLY, and must be received by Tecumseh or a Tecumseh Authorized Service Outlet within 30 days from the date of sale to

the original purchaser.

B. Products And Items Not Warranted

Alterations or Modiﬁcations of Power Train Components.

Accidents, Normal Maintenance, Failure to follow the Original Equipment Manufacturer’s Manual.

This warranty covers only parts of new Power Train Components which are found upon examination to be defective in material

or workmanship as delivered to the original purchaser. This warranty does not cover defects caused by depreciation or damage caused

by normal wear, accidents, improper maintenance, improper use or abuse of the product, failure to follow the instructions contained in

an Instruction Manual for the operation of the Power Train Component and parts. The cost of normal maintenance and replacement of

service items which are not defective shall be paid for by the original purchaser.

C. Securing Warranty Service

Warranty service can be arranged for by contacting either a Tecumseh Authorized Service Outlet (any Tecumseh Registered

Service Dealer, Tecumseh Authorized Service Distributor, or Tecumseh Central Warehouse Distributor) or by contacting Tecumseh, c/o

Service Manager, Engine and Transmission Group Service Division, 900 North Street, Grafton, Wisconsin 53024. Warranty service

can only be performed by a Tecumseh Authorized Service Outlet or by Tecumseh at its factory in Grafton, Wisconsin. At the time of

requesting warranty service, evidence must be presented of the date of sale to the original purchaser. The purchaser shall pay any

charges for making service calls and/or for transporting the product to and from the place where the inspection and/or warranty work

is performed. The purchaser shall be responsible for any damage or loss incurred in connection with the transportation of Power Train

Components and/or part(s) of the Power Train Components submitted for inspection and/or warranty work.

D. Limitation of Damages and Implied Warranties

The foregoing EXPRESSED WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES. Neither Tecumseh nor any

of its afﬁliates makes any warranties, representations or promises, written or oral, as to the quality of the Power Train Component or any

of its parts, other than as set forth herein.

ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, TO THE EXTENT THAT

EITHER MAY APPLY TO ANY PART(S) OF POWER TRAIN COMPONENTS, SHALL BE LIMITED IN DURATION TO THE PERIODS

OF THE EXPRESSED WARRANTIES DEFINED IN PARAGRAPH A HEREOF. IN NO EVENT WILL TECUMSEH BE LIABLE FOR ANY

INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES AND/OR EXPENSES. Some states do not allow limitations on how long

an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitation(s) or exclusion(s)

may not apply to you. This warranty gives you speciﬁc legal rights and you may also have other legal rights which vary from state to

state.

E. No Dealer Warranty

Tecumseh neither assumes nor authorizes any other person, natural or corporate, to assume forTecumseh any other obligations

or liabilities in connection with or with respect to any part(s) of a Power Train Component. The seller or dealer of part(s) of a Power Train

Component has no authority, whatsoever, to make any representations or promises on behalf of Tecumseh or to modify the terms or

limitations of Tecumseh’s warranty in any way.

Download from Www.Somanuals.com. All Manuals Search And Download.

SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION

ONLY RIDE UP AND DOWN HILL,

NOT ACROSS HILL

15 DEGREES MAX.

WARNING: To avoid serious injury, operate your tractor up and

down the face of slopes, never across the face. Do not mow

slopes greater than 15 degrees. Make turns gradually to prevent

tipping or loss of control. Exercise extreme caution when

changing direction on slopes.

1. Fold this page along dotted line indicated above.

2. Hold page before you so that its left edge is vertically parallel to a tree

trunk or other upright structure.

3. Sight across the fold in the direction of hill slope you want to measure.

4. Compare the angle of the fold with the slope of the hill.

Download from Www.Somanuals.com. All Manuals Search And Download.

PARTS AND SERVICE

This product has been expertly engineered and carefully manufactured to rigid quality standards. As with all

mechanical products, some adjustments or part replacement may be necessary during the life of your unit.

For Parts and service, contact our authorized distributor: call 1-800-849-1297

•

For replacement parts, have available the following information:

a. Model Number/Manufacturer's I.D. Number

b. Description of part.

For Techical Assistance: call 1-800-829-5886

For a Parts Manual, go to our website: www.weedeater.com/support.asp

NOTE: Electrolux Home Products provides parts and service through its authorized distributors and

dealers; therefore, all requests for parts and service should be directed to your local dealer(s).

The philosophy of Electrolux Home Products is to continually improve all of its products. If

the operating characteristics or the appearance of your product differs from those described

in this Manual, please contact your local dealer for updated information and assistance.

Download from Www.Somanuals.com. All Manuals Search And Download.

Billy Goat Lawn Mower KV600 User Manual
Bolens Lawn Mower 117 670A User Manual
Demco Lawn Mower Accessory Sprayer User Guide
Flymo Lawn Mower 5119627 03 User Guide
Hayter Mowers Lawn Mower 401C001001 User Guide
Land Pride Lawn Mower ZT60 Series User Guide
Rubbermaid Lawn Mower Accessory RMD108 User Guide
Snapper Lawn Mower 1691423 User Guide
Toro Lawn Mower 2000 D User Guide
Troy Bilt Lawn Mower 13027 User Guide