Weed Eater Lawn Mower 195383 User Guide

IMPORTANT MANUAL  
Do Not Throw Away  
®
01533  
OPERATOR'S MANUAL  
WARNING:  
Read this Manual and follow allWarnings and  
SafetyInstructions. Failuretodosocanresult  
in serious injury.  
MODEL:  
HD13538  
LAWN TRACTOR  
ALWAYS WEAR EYE PROTECTION DURING OPERATION  
195383 11.08.04 TR  
Printed in U.S.A.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY RULES  
Safe Operation Practices for Ride-On Mowers  
GENERAL SERVICE  
III. CHILDREN  
Never operate machine in a closed are.  
Keep all nuts and bolts tight to be sure the equipment  
is in safe working condition.  
Never tamper with safety devices. Check their proper  
operation regularly.  
Keep machine free of grass, leaves, or other debris  
build-up. Clean oil or fuel spillage and remove any fuel-  
soaked debris. Allow machine to cool before storing.  
If you strike a foreign object, stop and inspect the  
machine. Repair, if necessary, before restarting.  
Nevermakeanyadjustmentsorrepairswiththeengine  
running.  
Check grass catcher components and the discharge  
guard frequently and replace with manufacturer's rec-  
ommended parts, when necessary.  
Tragic accidents can occur if the operator is not alert to  
the presence of children. Children are often attracted to  
the machine and the mowing activity. Never assume that  
children will remain where you last saw them.  
Keepchildrenoutofthemowingareaandinthewatchful  
care of a responsible adult other than the operator.  
Be alert and turn machine off if a child enters the  
area.  
Before and while backing, look behind and down for  
small children.  
Nevercarrychildren,evenwiththebladesshutoff. They  
may fall off and be seriously injured or interfere with  
safemachineoperation.Childrenwhohavebeengiven  
rides in the past may suddenly appear in the mowing  
area for another ride and be run over or backed over  
by the machine.  
Never allow children to operate the machine.  
Useextracarewhenapproachingblindcorners,shrubs,  
trees, or other objects that may block your view of a  
child.  
Mower blades are sharp. Wrap the blade or wear  
gloves, and use extra caution when servicing them.  
Check brake operation frequently. Adjust and service  
as required.  
Maintain or replace safety and instruction labels, as  
necessary.  
IV.TOWING  
Tow only with a machine that has a hitch designed for  
towing. Do not attach towed equipment except at the  
hitch point.  
Follow the manufacturer's recommendation for weight  
limits for towed equipment and towing on slopes.  
Never allow children or others in or on towed equip-  
ment.  
On slopes, the weight of the towed equipment may  
cause loss of traction and loss of control.  
Travel slowly and allow extra distance to stop.  
Be sure the area is clear of bystanders before operat-  
ing. Stop machine if anyone enters the area.  
Never carry passengers.  
Do not mow in reverse unless absolutely necessary.  
Always look down and behind before and while back-  
ing.  
V. SERVICE  
SAFE HANDLING OF GASOLINE  
Nevercarrychildren,evenwiththebladesshutoff. They  
may fall off and be seriously injured or interfere with  
safemachineoperation.Childrenwhohavebeengiven  
rides in the past may suddenly appear in the mowing  
area for another ride and be run over or backed over  
by the machine.  
Keepchildrenoutofthemowingareaandinthewatchful  
care of a responsible adult other than the operator.  
Be alert and turn machine off if a child enters the  
area.  
Before and while backing, look behind and down for  
small children.  
Mow up and down slopes (15° Max), not across.  
Choose a low ground speed so that you will not have  
to stop or shift while on the slope.  
Avoid starting, stopping, or turning on a slope. If the  
tires lose traction, disengage the blades and proceed  
slowly straight down the slope.  
To avoid personal injury or property damage, use extreme  
care in handling gasoline.Gasoline is extremely flammable  
and the vapors are explosive.  
Extinguish all cigarettes, cigars, pipes, and other  
sources of ignition.  
Use only approved gasoline container.  
Never remove gas cap or add fuel with the engine run-  
ning. Allow engine to cool before refueling.  
Never fuel the machine indoors.  
Never store the machine or fuel container where there  
is an open flame, spark, or pilot light such as on a water  
heater or other appliances.  
Never fill containers inside a vehicle or on a truck or  
trailer bed with plastic liner. Always place containers  
on the ground away from your vehicle when filling.  
Removegas-poweredequipmentfromthetruckortrailer  
and refuel it on the ground. If this is not possible, then  
refuel such equipment with a portable container, rather  
than from a gasoline dispenser nozzle.  
Keep the nozzle in contact with the rim of the fuel tank  
orcontaineropeningatalltimesuntilfuelingiscomplete.  
Do not use a nozzle lock-open device.  
If machine stops while going uphill, disengage blades,  
shift into reverse and back down slowly.  
Do not turn on slopes unless necessary, and then, turn  
slowly and gradually downhill, if possible.  
If fuel is spilled on clothing, change clothing immedi-  
ately.  
Never overfill fuel tank. Replace gas cap and tighten  
securely.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONGRATULATIONS on your purchase of a new tractor.  
Ithasbeendesigned,engineeredandmanufacturedtogive  
you the best possible dependability and performance.  
PRODUCT SPECIFICATIONS  
Gasoline Capacity  
and Type:  
1.25 Gallons  
Unleaded Regular  
Shouldyouexperienceanyproblemyoucannoteasilyrem-  
edy,pleasecontactyournearestauthorizedservicecenter/  
department. We have competent, well-trained technicians  
and the proper tools to service or repair this tractor.  
Oil Type (API-SG-SL):  
SAE 30 (above 32°F)  
SAE 5W-30 (below 32°F)  
Oil Capacity:  
3.0 Pints  
Please read and retain this manual. The instructions will  
enable you to assemble and maintain your tractor properly.  
Always observe the “SAFETY RULES”.  
Spark Plug:  
(Gap: .030")  
Champion RC12YC  
Ground Speed (MPH):  
Forward:  
1st  
2nd  
1.1  
2.2  
3.3  
4.4  
4.9  
1.4  
CUSTOMER RESPONSIBILITIES  
3rd  
Read and observe the safety rules.  
4th  
5th  
Reverse:  
Follow a regular schedule in maintaining, caring for  
and using your tractor.  
Follow the instructions underMaintenanceandStor-  
age” sections of this owner’s manual.  
Tire Pressure:  
Charging System:  
Battery:  
Front:  
Rear:  
14 PSI  
12 PSI  
3 Amps Battery  
WARNING: This tractor is equipped with an internal com-  
bustion engine and should not be used on or near any  
unimprovedforest-covered,brush-coveredorgrass-covered  
land unless the engine’s exhaust system is equipped with  
a spark arrester meeting applicable local or state laws (if  
any). If a spark arrester is used, it should be maintained  
in effective working order by the operator.  
5 Amps Headlights  
AMP/HR:  
Min. CCA:  
Case Size:  
28  
230  
U1R  
Blade Torque:  
27-35 FT. LBS.  
A spark arrester for the muffler is available through your  
nearest authorized service center/department.  
TABLE OF CONTENTS  
SAFETY RULES .........................................................2-3  
PRODUCT SPECIFICATIONS....................................... 4  
CUSTOMER RESPONSIBILITIES................................. 4  
ASSEMBLY.................................................................6-8  
OPERATION .............................................................9-14  
MAINTENANCE SCHEDULE ...................................... 15  
MAINTENANCE .....................................................15-18  
SERVICE AND ADJUSTMENTS ............................19-23  
STORAGE.................................................................... 24  
TROUBLESHOOTING ............................................25-26  
WARRANTY................................................................. 27  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTENTS OF HARDWARE PACK  
Steering Wheel  
Seat  
(1) Washer  
17/32 x 1-3/16 x 12 Gauge  
Steering  
Boot  
(1) Lock  
Washer 1/2  
Steering  
Wheel  
Insert  
(1) Bolt  
Steering  
Wheel  
Adapter  
Key  
Steering  
Extension  
Shaft  
(1) Large Flat  
Washer  
(2) Keys  
(1) Oil Drain Tube  
Slope Sheet  
(1) 5/16  
Lock Washer  
(1) Hex Bolt 5/16-18 x 4  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes.  
To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use  
the correct tools as necessary to insure proper tightness.  
TOOLS REQUIRED FOR ASSEMBLY  
INSERT  
A socket wrench set will make assembly easier. Standard  
5/16 HEX BOLT  
wrench sizes are listed.  
5/16 LOCK  
(1) 1/2" wrench  
(1) 3/4" wrench  
Pliers  
Utility knife  
Tire pressure gauge  
WASHER  
LARGE FLAT  
WASHER  
Whenrightorlefthandismentionedinthismanual,itmeans  
when you are in the operating position (seated behind the  
steering wheel).  
STEERING  
WHEEL  
STEERING  
BOOT  
TO REMOVE TRACTOR FROM  
CARTON  
UNPACK CARTON  
TABS  
Remove all accessible loose parts and parts cartons  
from carton.  
Cut along dotted lines on all four panels of carton.  
Remove end panels and lay side panels flat.  
Check for any additional loose parts or cartons and  
remove.  
ADAPTER  
EXTENSION  
SHAFT  
LOWER  
STEERING  
SHAFT  
BEFORE REMOVING TRACTOR FROM  
SKID  
TAB  
SLOTS  
ATTACH STEERING WHEEL (See Fig. 1)  
ASSEMBLE EXTENSION SHAFT AND BOOT  
FIG. 1  
Slide extension shaft onto lower steering shaft.  
Place tabs of steering boot over tab slots in dash and  
push down to secure.  
INSTALL SEAT (See Fig. 2)  
Adjust seat before tightening adjustment bolt.  
INSTALL STEERING WHEEL  
Remove adjustment bolt, lock washer and flat washer  
securing seat to cardboard packing and set aside for  
assembly of seat to tractor.  
Position front wheels of the tractor so they are pointing  
straight forward.  
Remove steering wheel adapter from steering wheel  
and slide adapter onto steering shaft extension.  
Position steering wheel so cross bars are horizontal  
(left to right) and slide inside boot and onto adapter.  
Assemble large flat washer, 5/16 lock washer, 5/16 hex  
bolt and tighten securely.  
Snap steering wheel insert into center of steering  
wheel.  
Remove protective materials from tractor hood and  
grill.  
Pivotseatupwardandremovefromthecardboardpack-  
ing. Remove the cardboard packing and discard.  
Place seat on seat pan so head of shoulder bolt is  
positioned over large slotted hole in pan.  
Push down on seat to engage shoulder bolt in slot and  
pull seat towards rear of tractor.  
Pivot seat and pan forward and assemble adjust-  
ment bolt, lockwasher and flat washer loosely. Do not  
tighten  
Lower seat into operating position and sit on seat.  
IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN  
SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO  
ROLL OFF SKID.  
Slide seat until a comfortable position is reached  
which allows you to press clutch/brake pedal all the  
way down.  
Get off seat without moving its adjusted position.  
Raise seat and tighten adjustment bolt securely.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
NOTE: You may now roll or drive your tractor off the skid.  
Follow the appropriate instruction below to remove the  
tractor from the skid.  
SHOULDER  
BOLT  
SEAT  
TO ROLL TRACTOR OFF SKID (See Op-  
eration section for location and function of  
controls)  
Press lift lever plunger and raise attachment lift lever  
to its highest position.  
SEAT PAN  
Release parking brake by depressing clutch/brake  
pedal.  
Place gearshift lever in neutral (N) position.  
Roll tractor forward off skid.  
Remove banding holding deflector shield up against  
tractor.  
TO DRIVE TRACTOR OFF SKID (See Op-  
eration section for location and function of  
controls)  
WARNING: Before starting, read, understand and follow  
all instructions in the Operation section of this manual. Be  
sure tractor is in a well-ventilated area. Be sure the area in  
front of tractor is clear of other people and objects.  
FLAT WASHER  
LOCK WASHER  
02465  
Be sure all the above assembly steps have been com-  
pleted.  
ADJUSTMENT  
BOLT  
Check engine oil level and fill fuel tank with gasoline.  
Sit on seat in operating position, depress clutch/brake  
pedal and set the parking brake.  
FIG. 2  
Place gear shift lever in neutral (N) position.  
Press lift lever plunger and raise attachment lift lever  
to its highest position.  
Starttheengine.Afterenginehasstarted,movethrottle  
control to idle position.  
Depress clutch/brake pedal into full “BRAKE” position  
and hold. Move gearshift lever to 1st gear.  
Slowly release clutch/brake pedal and slowly drive  
tractor off skid.  
Apply brake to stop tractor, set parking brake and place  
gearshift lever in neutral position.  
CHECK BATTERY (See Fig. 3)  
Lift seat pan to raised position.  
If this battery is put into service after month and year  
indicated on label (label located between terminals)  
charge battery for minimum of one hour at 6-10 amps.  
(See "BATTERY" in MAINTENANCE section of this  
manual for charging instructions).  
SEAT PAN  
Turn ignition key to “OFF” position.  
LABEL  
Continue with the instructions that follow.  
TERMINAL  
TERMINAL  
FIG. 3  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
CHECK TIRE PRESSURE  
The tires on your tractor were overinflated at the factory  
for shipping purposes. Correct tire pressure is important  
for best cutting performance.  
CHECKLIST  
BEFORE YOU OPERATE YOUR NEW TRACTOR, WE  
WISHTO ASSURETHATYOU RECEIVETHE BEST PER-  
FORMANCE AND SATISFACTION FROMTHIS QUALITY  
PRODUCT.  
Reduce tire pressure to PSI shown in “PRODUCT  
SPECIFICATIONS” section of this manual.  
PLEASE REVIEW THE FOLLOWING CHECKLIST:  
All assembly instructions have been completed.  
CHECK DECK LEVELNESS  
For best cutting results, mower housing should be properly  
leveled. SeeTOLEVELMOWERHOUSINGintheService  
and Adjustments section of this manual.  
No remaining loose parts in carton.  
Battery is properly prepared and charged. (Minimum  
1 hour at 6 amps).  
Seat is adjusted comfortably and tightened securely.  
CHECK FOR PROPER POSITION OF ALL  
BELTS  
See the figures that are shown for replacing motion and  
mower blade drive belts in the Service and Adjustments  
section of this manual. Verify that the belts are routed  
correctly.  
All tires are properly inflated. (For shipping purposes,  
the tires were overinflated at the factory).  
Be sure mower deck is properly leveled side-to-side/  
front-to-rear for best cutting results. (Tires must be  
properly inflated for leveling).  
Check mower and drive belts. Be sure they are routed  
properly around pulleys and inside all belt keepers.  
CHECK BRAKE SYSTEM  
Afteryoulearnhowtooperateyourtractor,checktoseethat  
the brake is properly adjusted. See “TO ADJUST BRAKE”  
in the Service and Adjustments section of this manual.  
Check wiring. See that all connections are still secure  
and wires are properly clamped.  
WHILE LEARNING HOW TO USEYOUR TRACTOR, PAY  
EXTRA ATTENTION TO THE FOLLOWING IMPORTANT  
ITEMS:  
Engine oil is at proper level.  
Fuel tank is filled with fresh, clean, regular unleaded  
gasoline.  
Become familiar with all controls, their location and  
function. Operate them before you start the engine.  
Be sure brake system is in safe operating condition.  
Be sure Operator Presence System and Reverse Op-  
eration System (ROS) are working properly (See the  
Operation and Maintenance sections in this manual).  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their mean-  
ing.  
FAST  
SLOW  
REVERSE  
HIGH  
LOW  
NEUTRAL  
CHOKE  
IGNITION SWITCH  
P
ENGINE START  
ENGINE ON  
PARKING BRAKE  
REVERSE  
OPERATION  
SYSTEM (ROS)  
PARKING BRAKE PARKING BRAKE  
ENGINE OFF  
LOCKED  
UNLOCKED  
OIL PRESSURE  
BATTERY  
REVERSE  
FUEL  
FORWARD  
OVER TEMP  
LIGHT  
MOWER HEIGHT  
MOWER LIFT  
15  
15  
ATTACHMENT  
CLUTCH ENGAGED  
ATTACHMENT  
CLUTCH DISENGAGED  
SLOPE HAZARDS  
KEEP AREA CLEAR  
(SEE SAFETY RULES SECTION)  
DANGER, KEEP HANDS  
AND FEET AWAY  
DANGER indicates a hazard which, if not avoided,  
will result in death or serious injury.  
LIGHTS ON  
WARNING indicates a hazard which, if not avoided,  
could result in death or serious injury.  
FREE WHEEL  
(Automatic Models only)  
CAUTION indicates a hazard which, if not avoided,  
might result in minor or moderate injury.  
CAUTION when used without the alert symbol,  
indicates a situation that could result in damage  
to the tractor and/or engine.  
Failure to follow instructions  
could result in serious injury or  
death. The safety alert symbol  
is used to identify safety inform-  
ation about hazards which can  
result in death, serious injury  
and/or property damage.  
HOT SURFACES indicates a hazard which,  
if not avoided, could result in death, serious injury  
and/or property damage.  
FIRE indicates a hazard which, if not avoided,  
could result in death, serious injury and/or  
property damage.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
KNOWYOUR TRACTOR  
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATINGYOUR TRACTOR  
Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments.  
Save this manual for future reference.  
ATTACHMENT  
ROS "ON"  
IGNITION  
CLUTCH LEVER  
POSITION  
SWITCH  
LIFT LEVER  
PLUNGER  
LIGHT SWITCH  
ATTACHMENT  
LIFT LEVER  
THROTTLE/CHOKE  
CONTROL  
HEIGHT  
ADJUSTMENT  
INDICATOR  
CLUTCH/BRAKE  
PEDAL  
PARKING  
BRAKE  
GEAR SHIFT  
LEVER  
02829  
FIG. 4  
Our tractors conform to the safety standards of the American National Standards Institute.  
ATTACHMENT CLUTCH LEVER - Used to engage the  
LIFT LEVER PLUNGER - Used to release attachment lift  
mower blades, or other attachments mounted to your  
tractor.  
lever when changing its position.  
LIGHT SWITCH - Turns the headlights on and off.  
PARKING BRAKE - Locks clutch/brake pedal into the  
brake position.  
REVERSE OPERATION SYSTEM (ROS) “ON” POSI-  
TION - Allows operation of mower deck or other powered  
attachment while in reverse.  
THROTTLE/CHOKE CONTROL - Used for starting and  
controlling engine speed.  
ATTACHMENT LIFT LEVER - Used to raise, lower, and  
adjust the mower deck or other attachments mounted to  
your tractor.  
CLUTCH/BRAKEPEDAL-Usedfordeclutchingandbrak-  
ing the tractor and starting the engine.  
GEARSHIFT LEVER - Selects the speed and direction  
of the tractor.  
IGNITION SWITCH - Used for starting and stopping the  
engine.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
The operation of any tractor can result in foreign objects thrown into the eyes, which can result  
in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or  
performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles  
or standard safety glasses.  
NOTE: Under certain conditions when tractor is standing  
HOW TO USEYOUR TRACTOR  
idlewiththeenginerunning, hotengineexhaustgasesmay  
cause “browning” of grass. To eliminate this possibility, al-  
ways stop engine when stopping tractor on grass areas.  
TO SET PARKING BRAKE (See Fig. 5)  
Your tractor is equipped with an operator presence sens-  
ing switch. When engine is running, any attempt by the  
operator to leave the seat without first setting the parking  
brake will shut off the engine.  
CAUTION: Always stop tractor com-  
pletely,asdescribedabove,beforeleav-  
ing the operator's position; to empty  
grass catcher, etc.  
Depress clutch/brake pedal into full “BRAKE” position  
and hold.  
Place parking brake lever inENGAGEDposition and  
releasepressurefromclutch/brakepedal. Pedalshould  
remain in “BRAKE” position. Make sure parking brake  
will hold tractor secure.  
TO USE THROTTLE CONTROL (See Fig. 5)  
Always operate engine at full throttle.  
Operating engine at less than full throttle reduces the  
battery charging rate.  
Full throttle offers the best bagging and mower perfor-  
mance.  
ATTACHMENT CLUTCH  
LEVER "ENGAGED"  
POSITION  
TO MOVE FORWARD AND BACKWARD  
(See Fig. 5)  
The direction and speed of movement is controlled by the  
gearshift lever.  
IGNITION KEY  
THROTTLE/  
CHOKE  
"DISENGAGED"  
POSITION  
CONTROL  
LEVER  
PARKING BRAKE  
"ENGAGED"  
POSITION  
Start tractor with clutch/brake pedal depressed and  
gearshift lever in neutral (N) position.  
Move gearshift lever to desired position.  
Slowly release clutch/brake pedal to start move-  
ment.  
"BRAKE"  
POSITION  
GEAR SHIFT  
LEVER  
IMPORTANT: BRING TRACTOR TO A COMPLETE STOP  
BEFORE SHIFTING OR CHANGING GEARS. FAILURE  
TO DO SO WILL SHORTEN THE USEFUL LIFE OF YOUR  
TRANSAXLE.  
CLUTCH/BRAKE  
PEDAL "DRIVE"  
POSITION  
PARKING BRAKE  
"DISENGAGED"  
POSITION  
FIG. 5  
TO ADJUST MOWER CUTTING HEIGHT  
(See Fig. 5)  
The position of the attachment lift lever determines the  
cutting height.  
STOPPING (See Fig. 5)  
MOWER BLADES -  
To stop mower blades,move attachment clutch lever  
to “DISENGAGED” position.  
Grasp lift lever.  
Press plunger with thumb and move lever to desired  
position.  
GROUND DRIVE -  
To stop ground drive, depress clutch/brake pedal into  
The cutting height range is approximately 1-1/2 to 4".  
The heights are measured from the ground to the blade tip  
withtheenginenotrunning. Theseheightsareapproximate  
and may vary depending upon soil conditions, height of  
grass and types of grass being mowed.  
full “BRAKE” position.  
Move gearshift lever to neutral (N) position.  
ENGINE -  
Move throttle control between half and full speed (fast)  
position.  
The average lawn should be cut to approximately 2-1/2  
inches during the cool season and to over 3 inches  
during hot months. For healthier and better looking  
lawns, mow often and after moderate growth.  
NOTE: Failure to move throttle control between half and  
fullspeed(fast)position,beforestoppingmaycauseengine  
to “backfi r e ” .  
For best cutting performance, grass over 6 inches  
in height should be mowed twice. Make the first cut  
relatively high; the second to desired height.  
Turn ignition key to “OFF” position and remove key.  
Always remove key when leaving tractor to prevent  
unauthorized use.  
Never use choke to stop engine.  
IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY  
POSITION OTHER THAN "OFF" WILL CAUSE THE BATTERY  
TO BE DISCHARGED, (DEAD).  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
REVERSE OPERATION SYSTEM (ROS)  
"ENGAGED" POSITION  
Your tractor is equipped with a Reverse Operation System  
(ROS). Any attempt by the operator to travel in the reverse  
direction with the attachment clutch engaged will shut off  
the engine unless ignition key is placed in the ROS "ON"  
position.  
ATTACHMENT  
LIFT LEVER  
HIGH POSITION  
LOW  
POSITION  
WARNING: Backing up with the attachment clutch en-  
gaged while mowing is strongly discouraged. Turning the  
ROS "ON", to allow reverse operation with the attachment  
clutch engaged, should only be done when the operator  
decides it is necessary to reposition the machine with the  
attachment engaged. Do not mow in reverse unless  
absolutely necessary.  
ATTACHMENT  
CLUTCH LEVER  
"DISENGAGED"  
POSITION  
USING THE REVERSE OPERATION SYSTEM -  
Depress clutch/brake pedal all the way down and  
hold.  
DEFLECTOR  
SHIELD  
Withenginerunning,turnignitionkeycounterclockwise  
to ROS "ON" position.  
FIG. 6  
Look down and behind before backing.  
Move gear shift lever to reverse (R) position and slowly  
release clutch/brake pedal to start movement.  
TO OPERATE ON HILLS  
When use of the ROS is no longer needed, turn the  
ignition key clockwise to engine "ON" position.  
WARNING: Do not drive up or down  
hills with slopes greater than 15° and  
do not drive across any slope.  
ROS "ON" POSITION  
ENGINE "ON" POSITION  
(NORMAL OPERATING)  
Choose the slowest speed before starting up or down  
hills.  
Avoid stopping or changing speed on hills.  
If slowing is necessary, move throttle control lever to  
slower position.  
If stopping is absolutely necessary, push clutch/brake  
pedal quickly to brake position and engage parking  
brake.  
Move gearshift lever to 1st gear. Be sure you have  
allowed room for tractor to roll slightly as you restart  
movement.  
TO OPERATE MOWER (See Fig. 6)  
Yourtractor isequippedwithanoperatorpresencesensing  
switch. Any attempt by the operator to leave the seat with  
the engine running and the attachment clutch engaged  
will shut off the engine.You must remain fully and centrally  
positioned in the seat to prevent the engine from hesitating  
or cutting off when operating your equipment on rough,  
rolling terrain or hills.  
Torestartmovement, slowlyreleaseparkingbrakeand  
clutch/brake pedal.  
Make all turns slowly.  
TO TRANSPORT  
Raiseattachmentlifttohighestpositionwithattachment  
lift control.  
When pushing or towing your tractor, be sure gearshift  
lever is in neutral (N) position.  
Select desired height of cut.  
Start mower blades by engaging attachment clutch  
control.  
Do not push or tow tractor at more than five (5) MPH.  
TO STOP MOWER BLADES - disengage attachment  
clutch control.  
NOTE: To protect hood from damage when transporting  
your tractor on a truck or a trailer, be sure hood is closed  
and secured to tractor. Use an appropriate means of tying  
hood to tractor (rope, cord, etc.).  
CAUTION: Do not operate the mower  
without either the entire grass catcher,  
onmowerssoequipped,orthedeflector  
shield in place.  
TOWING CARTS AND OTHER ATTACH-  
MENTS  
Tow only the attachments that are recommended by and  
comply with specifications of the manufacturer of your trac-  
tor. Use common sense when towing.Too heavy of a load,  
while on a slope, is dangerous.Tires can lose traction with  
the ground and cause you to lose control of your tractor.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
TO START ENGINE (See Fig. 5)  
When starting the engine for the first time or if the engine  
has run out of fuel, it will take extra cranking time to move  
fuel from the tank to the engine.  
BEFORE STARTING THE ENGINE  
CHECK ENGINE OIL LEVEL  
The engine in your tractor has been shipped, from the  
factory, already filled with summer weight oil.  
Sit on seat in operating position, depress clutch/brake  
pedal and set parking brake.  
Check engine oil with tractor on level ground.  
Place gear shift lever in neutral (N) position.  
Move attachment clutch to “DISENGAGED” position.  
Move throttle control to choke ( ) position.  
Remove oil fill cap/dipstick and wipe clean, reinsert the  
dipstick and screw cap tight, wait for a few seconds,  
remove and read oil level. If necessary, add oil until  
“FULLmark on dipstick is reached. Do not overfill.  
NOTE: Before starting, read the warm and cold starting  
procedures below.  
For cold weather operation you should change oil for  
easier starting (See “OIL VISCOSITY CHART” in the  
Maintenance section of this manual).  
To change engine oil, see the Maintenance section in  
this manual.  
InsertkeyintoignitionandturnkeyclockwisetoSTART”  
position and release key as soon as engine starts.  
Do not run starter continuously for more than fifteen  
seconds per minute. If the engine does not start after  
several attempts, move throttle control to fast position,  
wait a few minutes and try again. If engine still does  
not start, move the throttle control back to the choke (  
) position and retry.  
ADD GASOLINE  
Fill fuel tank to bottom of filler neck. Do not overfill.  
Use fresh, clean, regular unleaded gasoline with a  
minimum of 87 octane. (Use of leaded gasoline will  
increase carbon and lead oxide deposits and reduce  
valve life). Do not mix oil with gasoline. Purchase fuel  
in quantities that can be used within 30 days to assure  
fuel freshness.  
WARM WEATHER STARTING (50° F and above)  
When engine starts, move the throttle control to the  
fast position.  
The attachments and ground drive can now be used. If  
the engine does not accept the load, restart the engine  
and allow it to warm up for one minute using the choke  
as described above.  
CAUTION: Wipe off any spilled oil or  
fuel. Do not store, spill or use gasoline  
near an open flame.  
COLD WEATHER STARTING ( 50° F and below)  
Whenenginestarts,allowenginetorunwiththethrottle  
control in the choke ( ) position until the engine runs  
roughly, then move throttle control to fast position.This  
may require an engine warm-up period from several  
seconds to several minutes, depending on the tem-  
perature.  
IMPORTANT: WHEN OPERATING IN TEMPERATURES  
BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE  
GASOLINE TO HELP INSURE GOOD COLD WEATHER  
STARTING.  
CAUTION: Alcohol blended fuels (called  
gasohol or using ethanol or methanol) can at-  
tract moisture which leads to separation and  
formation of acids during storage. Acidic gas  
can damage the fuel system of an engine while  
in storage. To avoid engine problems, the fuel  
system should be emptied before storage of  
30 days or longer. Drain the gas tank, start  
the engine and let it run until the fuel lines  
and carburetor are empty. Use fresh fuel next  
season. SeeStorageInstructionsforadditional  
information. Never use engine or carburetor  
cleaner products in the fuel tank or permanent  
damage may occur.  
The attachments can also be used during the engine  
warm-up period.  
NOTE: If at a high altitude (above 3000 feet) or in cold  
temperatures (below 32 F) the carburetor fuel mixture may  
need to be adjusted for best engine performance. See “TO  
ADJUST CARBURETOR” in the Service and Adjustments  
section of this manual.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
MOWING TIPS  
Mower should be properly leveled for best mowing per-  
formance. See"TOLEVELMOWERHOUSING"inthe  
Service and Adjustments section of this manual.  
The left hand side of mower should be used for trim-  
ming.  
Drive so that clippings are discharged onto the area  
that has been cut. Have the cut area to the right of the  
machine. This will result in a more even distribution of  
clippings and more uniform cutting.  
Whenmowinglargeareas,startbyturningtotherightso  
that clippings will discharge away from shrubs, fences,  
driveways, etc. After one or two rounds, mow in the  
opposite direction making left hand turns until finished  
(See Fig. 7).  
FIG. 7  
If grass is extremely tall, it should be mowed twice to  
reduce load and possible fire hazard from dried clip-  
pings. Make first cut relatively high; the second to the  
desired height.  
Do not mow grass when it is wet. Wet grass will plug  
mower and leave undesirable clumps. Allow grass to  
dry before mowing.  
Always operate engine at full throttle when mow-  
ing to assure better mowing performance and proper  
discharge of material. Regulate ground speed by se-  
lecting a low enough gear to give the mower cutting  
performance as well as the quality of cut desired.  
When operating attachments, select a ground speed  
that will suit the terrain and give best performance of  
the attachment being used.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
MAINTENANCE SCHEDULE  
USE  
HOURS  
HOURS  
FILL IN DATES  
HOURSHOURS  
50 100  
STORAGE  
EACH  
8
25  
SEASON  
AS YOU COMPLETE  
REGULAR SERVICE  
BEFORE  
SERVICE DATES  
EVERY EVERY EVERY EVERY EVERY  
BEFORE  
Check Brake Operation  
Check Tire Pressure  
Check Operator Presence and  
ROS Systems  
T
Check for Loose Fasteners  
R
5
A
Sharpen/Replace Mower Blades  
3
C
Lubrication Chart  
T
Check Battery Level  
4
0
Clean Battery and Terminals  
R
Check Transaxle Cooling  
Check V-Belts  
Check Engine Oil Level  
Change Engine Oil (with oil filter)  
1,2  
Change Engine Oil (without oil filter)  
1,2  
E
Clean Air Filter  
N
2
2
G
Clean Air Screen  
I
Inspect Muffler/Spark Arrester  
N
Replace Oil Filter (If equipped)  
1,  
2
2
E
Clean Engine Cooling Fins  
Replace Spark Plug  
Replace Air Filter Paper Cartridge  
Replace Fuel Filter  
2
3 - Replace blades more often when mowing in sandy soil.  
4 - Not required if equipped with maintenance-free battery.  
5 - Tighten front axle pivot bolt to 35 ft.-lbs. maximum.  
Do not overtighten.  
1 - Change more often when operating under a heavy load or  
in high ambient temperatures.  
2 - Service more often when operating in dirty or dusty conditions.  
LUBRICATION CHART  
dSPINDLE ZERK  
GENERAL RECOMMENDATIONS  
dSPINDLE ZERK  
The warranty on this tractor does not cover items that have  
beensubjectedtooperatorabuseornegligence. Toreceive  
full value from the warranty, operator must maintain tractor  
as instructed in this manual.  
dFRONT WHEEL  
dFRONT WHEEL  
BEARING ZERK  
BEARING ZERK  
Some adjustments will need to be made periodically to  
properly maintain your tractor.  
At least once a season, check to see if you should make  
any of the adjustments described in the Service and  
Adjustments section of this manual.  
eENGINE  
• At least once a year you should replace the spark plug,  
clean or replace air filter, and check blades and belts  
for wear. A new spark plug and clean air filter assure  
proper air-fuel mixture and help your engine run better  
and last longer.  
cGEARSHIFT  
PIVOTS  
BEFORE EACH USE  
cSAE 30 OR 10W30 MOTOR OIL  
dGENERAL PURPOSE GREASE  
eREFER TO MAINTENANCE “ENGINE” SECTION  
Check engine oil level.  
Check brake operation.  
Check tire pressure.  
Check operator presence and  
ROS systems for proper operation.  
Check for loose fasteners.  
IMPORTANT: DO NOT OIL OR GREASE THE PIVOT POINTS WHICH  
HAVE SPECIAL NYLON BEARINGS. VISCOUS LUBRICANTS WILL  
ATTRACT DUST AND DIRT THAT WILL SHORTEN THE LIFE OF  
THE SELF-LUBRICATING BEARINGS. IF YOU FEEL THEY MUST  
BE LUBRICATED, USE ONLY A DRY, POWDERED GRAPHITE TYPE  
LUBRICANT SPARINGLY.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
BLADE CARE  
Forbestresultsmowerbladesmustbekeptsharp. Replace  
bent or damaged blades.  
TRACTOR  
Always observe safety rules when performing any main-  
tenance.  
BRAKE OPERATION  
CAUTION: Useonlyareplacementblade  
approved by the manufacturer of your  
tractor. Using a blade not approved  
by the manufacturer of your tractor is  
hazardous, could damage your tractor  
and void your warranty.  
If tractor requires more than five (5) feet to stop at highest  
speed in highest gear on a level, dry concrete or paved  
surface, then brake must be checked and adjusted. (See  
“TO ADJUST BRAKE” in the Service and Adjustments  
section of this manual).  
TIRES  
BLADE REMOVAL (See Fig. 8)  
Maintainproperairpressureinalltires(SeePRODUCT  
Raise mower to highest position to allow access to  
blades.  
SPECIFICATIONS” section of this manual).  
Keep tires free of gasoline, oil, or insect control chemi-  
cals which can harm rubber.  
Avoid stumps, stones, deep ruts, sharp objects and  
other hazards that may cause tire damage.  
Removebladebolt,lockwasherandatwashersecuring  
blade.  
Install new or resharpened blade with trailing edge up  
towards deck as shown.  
NOTE: To seal tire punctures and prevent flat tires due to  
slow leaks, tire sealant may be purchased from your local  
parts dealer. Tire sealant also prevents tire dry rot and  
corrosion.  
IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER  
HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL  
ASSEMBLY.  
Reassemble blade bolt, lock washer and flat washer  
in exact order as shown.  
OPERATOR PRESENCE SYSTEM AND REVERSE OP-  
ERATION SYSTEM (ROS)  
Tighten blade bolt securely (27-35 Ft. Lbs. torque).  
Be sure operator presence and reverse operation systems  
are working properly. If your tractor does not function as  
described, repair the problem immediately.  
IMPORTANT: BLADEBOLTISHEATTREATED.IFBOLTNEEDS  
REPLACING, REPLACE ONLYWITH APPROVE BOLT SHOWN  
IN THE REPAIR PARTS.  
The engine should not start unless the brake pedal is  
fully depressed, and the attachment clutch control is  
in the disengaged position.  
MANDREL  
ASSEMBLY  
TRAILING  
EDGE UP  
BLADE  
CENTER  
HOLE  
CHECK OPERATOR PRESENCE SYSTEM  
Whentheengineisrunning,anyattemptbytheoperator  
to leave the seat without first setting the parking brake  
should shut off the engine.  
When the engine is running and the attachment clutch  
is engaged, any attempt by the operator to leave the  
seat should shut off the engine.  
FLAT WASHER  
LOCK WASHER  
STAR  
BLADE BOLT  
The attachment clutch should never operate unless  
the operator is in the seat.  
FIG. 8  
CHECK REVERSE OPERATION (ROS) SYSTEM  
When the engine is running with the ignition switch in  
the engine "ON" position and the attachment clutch  
engaged, any attempt by the operator to shift into  
reverse should shut off the engine.  
TO SHARPEN BLADE (See Fig. 9)  
NOTE: We do not recommend sharpening blade - but if  
you do, be sure the blade is balanced.  
Care should be taken to keep the blade balanced. An un-  
balancedbladewillcauseexcessivevibrationandeventual  
damage to mower and engine.  
When the engine is running with the ignition switch in  
the ROS "ON" position and the attachment clutch en-  
gaged, any attempt by the operator to shift into reverse  
should NOT shut off the engine.  
The blade can be sharpened with a file or on a grind-  
ing wheel. Do not attempt to sharpen while on the  
mower.  
ROS "ON" POSITION  
ENGINE "ON" POSITION  
(NORMAL OPERATING)  
To check blade balance, you will need a 5/8" diameter  
steel bolt, pin, or a cone balancer. (When using a  
cone balancer, follow the instructions supplied with  
balancer.)  
NOTE: Do not use a nail for balancing blade. The lobes of  
the center hole may appear to be centered, but are not.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
Slidebladeontoanunthreadedportionofthesteelbolt  
SAE VISCOSITY GRADES  
or pin and hold the bolt or pin parallel with the ground.  
If blade is balanced, it should remain in a horizontal  
position. If either end of the blade moves downward,  
sharpen the heavy end until the blade is balanced.  
SAE 30  
5W-30  
-20  
0
30  
32 40  
0
100  
60  
20  
80  
F
C
-20  
10  
-30  
-10  
30  
40  
CENTER HOLE  
TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE  
oil_visc_chart1_e  
FIG. 10  
BLADE  
5/8" BOLT  
OR PIN  
NOTE: Although multi-viscosity oils (5W30, 10W30 etc.)  
improvestartingincoldweather,theywillresultinincreased  
oilconsumptionwhenusedabove3F. Checkyourengine  
oil level more frequently to avoid possible engine damage  
from running low on oil.  
FIG. 9  
Change the oil after every 25 hours of operation or at least  
once a year if the tractor is not used for 25 hours in one  
year.  
BATTERY  
Yourtractorhasabatterychargingsystemwhichissufficient  
for normal use. However, periodic charging of the battery  
with an automotive charger will extend its life.  
Check the crankcase oil level before starting the engine  
and after each eight (8) hours of operation. Tighten oil fill  
cap/dipstick securely each time you check the oil level.  
Keep battery and terminals clean.  
Keep battery bolts tight.  
Keep small vent holes open.  
Recharge at 6-10 amperes for 1 hour.  
TO CHANGE ENGINE OIL (See Figs. 10 and 11)  
Determine temperature range expected before oil change.  
All oil must meet API service classification SG-SL.  
NOTE: The original equipment battery on your tractor is  
maintenance free. Do not attempt to open or remove caps  
or covers. Adding or checking level of electrolyte is not  
necessary.  
Be sure tractor is on level surface.  
Oil will drain more freely when warm.  
Catch oil in a suitable container.  
Remove oil fill cap/dipstick. Be careful not to allow dirt  
to enter the engine when changing oil.  
TO CLEAN BATTERY AND TERMINALS  
Corrosion and dirt on the battery and terminals can cause  
the battery to “leak” power.  
Remove yellow cap from end of drain valve and install  
the drain tube onto the fitting.  
Disconnect BLACK battery cable first then RED bat-  
tery cable and remove battery from tractor.  
OIL DRAIN VALVE  
Rinse the battery with plain water and dry.  
Cleanterminalsandbatterycableendswithwirebrush  
until bright.  
Coat terminals with grease or petroleum jelly.  
Reinstall battery (See “REPLACING BATTERY” in the  
Service and Adjustment section of this manual).  
CLOSED  
AND  
LOCKED  
POSITION  
DRAIN  
YELLOW CAP  
TUBE  
V-BELTS  
CheckV-beltsfordeteriorationandwearafter100hoursand  
replace if necessary.The belts are not adjustable.Replace  
belts if they begin to slip from wear.  
FIG. 11  
Unlock drain valve by pushing inward and turning  
counterclockwise.  
To open, pull out on the drain valve.  
After oil has drained completely, close and lock the  
drain valve by pushing inward and turning clockwise  
until the pin is in the locked position as shown.  
TRANSAXLE COOLING  
Keep transaxle free from build-up of dirt and chaff which  
can restrict cooling.  
ENGINE  
Remove the drain tube and replace the cap onto to the  
bottom fitting of the drain valve.  
Refill engine with oil through oil fill dipstick tube. Pour  
slowly. Do not overfill. For approximate capacity see  
“PRODUCT SPECIFICATIONS” section of this man-  
ual.  
LUBRICATION  
Only use high quality detergent oil rated with API service  
classification SG-SL. Select the oil’s SAE viscosity grade  
according to your expected operating temperature.  
Use gauge on oil fill cap/dipstick for checking level.  
Be sure dipstick cap is tightened securely for accurate  
reading. Keep oil atFULLline on dipstick.Tighten cap  
onto the tube securely when finished.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
CLEAN AIR SCREEN  
IN-LINE FUEL FILTER (See Fig. 12)  
The fuel filter should be replaced once each season. If fuel  
filter becomes clogged, obstructing fuel flow to carburetor,  
replacement is required.  
Air screen must be kept free of dirt and chaff to prevent  
engine damage from overheating. Clean with a wire brush  
or compressed air to remove dirt and stubborn dried gum  
fibers.  
With engine cool, remove filter and plug fuel line sec-  
tions.  
Place new fuel filter in position in fuel line with arrow  
pointing towards carburetor.  
Be sure there are no fuel line leaks and clamps are  
properly positioned.  
Immediately wipe up any spilled gasoline.  
AIR FILTER  
Your engine will not run properly using a dirty air filter.  
Service air cleaner more often under dusty conditions.See  
Engine Manual.  
MUFFLER  
Inspect and replace corroded muffler and spark arrester  
(if equipped) as it could create a fire hazard and/or dam-  
age.  
CLAMP  
CLAMP  
SPARK PLUGS  
Replace spark plugs at the beginning of each mowing sea-  
son or after every 100 hours of use, whichever comes first.  
Spark plug type and gap setting is shown in "PRODUCT  
SPECIFICATIONS" section of this manual.  
FUEL  
FILTER  
FIG. 12  
CLEANING  
Clean engine, battery, seat, finish, etc. of all foreign  
matter.  
Keep finished surfaces and wheels free of all gasoline,  
oil, etc.  
Protect painted surfaces with automotive type wax.  
We do not recommend using a garden hose or pressure  
washer to clean your tractor unless the engine and trans-  
mission are covered to keep water out. Water in engine or  
transmission will shorten the useful life of your tractor. Use  
compressed air or a leaf blower to remove grass, leaves  
and trash from tractor and mower.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUST-  
MENTS:  
Depress clutch/brake pedal fully and set parking brake.  
Place gearshift lever in neutral (N) position.  
Place attachment clutch in “DISENGAGED” position.  
Turn ignition key to “STOP” and remove key.  
Make sure the blades and all moving parts have completely stopped.  
Disconnect spark plug wire from spark plug and place wire where it cannot come in contact  
with plug.  
IMPORTANT:IFANATTACHMENTOTHERTHANTHEMOWER  
DECK ISTO BE MOUNTED ONTHETRACTOR, REMOVETHE  
FRONTLINKSANDHOOKTHECLUTCHSPRINGINTOSQUARE  
TRACTOR  
TO REMOVE MOWER (See Fig. 13)  
Mower will be easier to remove from the right side of trac-  
tor.  
HOLE IN FRAME.  
TO INSTALL MOWER (See Fig. 13)  
Place attachment clutch in “DISENGAGED” position.  
Move attachment lift lever forward to lower mower to  
its lowest position.  
Raise attachment lift lever to its highest position.  
Slide mower under tractor with deflector shield to right  
side of tractor.  
Roll belt off engine pulley.  
Removesmallretainerspring,andremoveclutchspring  
off pulley bolt.  
Lower lift lever to its lowest position.  
Connect front links to mower deck and secure with  
retainer springs..  
Remove large retainer spring, slide collar off and push  
housing guide out of bracket.  
Disconnect anti-swaybar from chassis bracket by re-  
moving retainer spring.  
Disconnect suspension arms from rear deck brackets  
by removing retainer springs.  
Disconnect front links from deck by removing retainer  
springs.  
Connect suspension arms to rear deck brackets and  
secure with retainer springs.  
Connect anti-swaybar to chassis bracket and secure  
with retainer spring.  
Push clutch cable housing guide into bracket, slide col-  
lar onto guide and secure with large retainer spring.  
Place flat washer and clutch spring on idler pulley bolt  
and secure with small retainer spring.  
Raise lift lever to raise suspension arms. Slide mower  
out from under tractor.  
Install belt onto engine pulley.  
SMALL  
RETAINER  
SPRING  
FLAT WASHER  
SUSPENSION  
ARMS  
SQUARE HOLE  
CLUTCH SPRING  
ENGINE PULLEY  
FRONT LINK  
RETAINER SPRING  
ANTI-SWAY BAR  
COLLAR  
RETAINER SPRINGS  
(BOTH SIDES)  
HOUSING GUIDE  
02695  
LARGE RETAINER  
SPRING  
CLUTCH SPRING  
DEFLECTOR SHIELD  
BRACKET  
FIG. 13  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
When distance “D” is 1/8" to 1/2" lower at front than  
rear, tighten nuts “F” against trunnion on both front  
links.  
To raise front of mower, loosen nutFfrom trunnion on  
both front links. Tighten nut “E” on both front links an  
equal number of turns.The two front links must remain  
equal in length.  
WhendistanceDis1/8"to1/2"loweratfrontthanrear,  
tighten nut “F” against trunnion on both front links.  
TO LEVEL MOWER HOUSING  
Adjust the mower while tractor is parked on level ground  
or driveway. Make sure tires are properly inflated (See  
“PRODUCT SPECIFICATIONSsection of this manual). If  
tires are over or underinflated, you will not properly adjust  
your mower.  
SIDE-TO-SIDE ADJUSTMENT (See Figs. 14 and 15)  
Raise mower to its highest position.  
At the midpoint of both sides of mower, measure height  
from bottom edge of mower to ground. Distance “A”  
on both sides of mower should be the same or within  
1/4" of each other.  
Recheck side-to-side adjustment.  
MANDREL  
If adjustment is necessary, make adjustment on one  
side of mower only.  
To raise one side of mower, tighten lift link adjustment  
nut on that side.  
To lower one side of mower, loosen lift link adjustment  
nut on that side.  
“D”  
“D”  
FIG. 16  
NOTE: Each full turn of adjustment nut will change mower  
height about 1/8".  
BOTH FRONT LINKS MUST BE EQUAL IN LENGTH  
Recheck measurements after adjusting.  
BOTTOM EDGE  
OF MOWER TO  
GROUND  
BOTTOM EDGE  
OF MOWER TO  
GROUND  
NUT “F”  
A
A
NUT “E”  
GROUND LINE  
FIG. 14  
TRUNNION  
SUSPENSION ARM  
FRONT LINKS  
LIFT LINK  
ADJUSTMENT NUT  
FIG. 17  
TO REPLACE MOWER BLADE DRIVE BELT  
(See Fig. 18)  
FIG. 15  
The mower blade drive belt may be replaced without tools.  
FRONT-TO-BACK ADJUSTMENT (See Figs. 16 and 17)  
Park the tractor on level surface. Engage parking brake.  
IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE  
FOLLOWINGFRONT-TO-BACKADJUSTMENTISNECESSARY,  
BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO  
MOWER WILL STAY LEVEL SIDE-TO-SIDE.  
BELT REMOVAL -  
Place attachment clutch in “DISENGAGED” position.  
Move attachment lift lever forward to lower mower to  
its lowest position.  
To obtain the best cutting results, the mower housing  
should be adjusted so that the front is approximately 1/8"  
to 1/2" lower than the rear when the mower is in its high-  
est position.  
Roll belt off engine pulley.  
DisconnectR.H.suspensionarmfromreardeckbracket  
by removing retainer spring.  
Checkadjustmentonrightsideoftractor. Measuredistance  
“D” directly in front and behind the mandrel at bottom edge  
of mower housing as shown.  
Work belt off both mandrel pulleys and idler pulleys.  
Pull belt away from mower.  
BELT INSTALLATION -  
Before making any necessary adjustments, check that  
both front links are equal in length.  
If links are not equal in length, adjust one link to same  
length as other link.  
To lower front of mower loosen nut “E” on both front  
links an equal number of turns.  
Work new belt around both mandrel pulleys and idler  
pulleys.  
Install new belt into engine pulley groove.  
Reconnect R.H. suspension arm and secure with re-  
tainer spring.  
Make sure belt is in all pulley grooves and inside all  
belt guides.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
TO REPLACE MOTION DRIVE BELT  
(See Fig. 20)  
IDLER PULLEYS  
Park the tractor on level surface. Engage parking brake.  
For assistance, there is a belt installation guide decal on  
bottom side of left footrest.  
BELT REMOVAL -  
Remove mower (See “TO REMOVE MOWER” in this  
section of manual).  
NOTE: Observe entire motion drive belt and position of all  
belt guides and keepers.  
Remove belt from stationary idler and clutching idler.  
Remove belt downward from around engine pulley.  
Pull belt slack toward rear of tractor. Remove belt  
upwards from transaxle pulley by deflecting belt keep-  
ers.  
MANDREL PULLEYS  
FIG. 18  
Remove belt from center span keeper and pull belt  
away from tractor.  
TO CHECK AND ADJUST BRAKE  
(See Fig. 19)  
Your tractor is equipped with an adjustable brake system  
which is mounted on the right side of the transaxle.  
BELT INSTALLATION -  
Carefully work new belt down between transaxle belt  
keepers and onto the input pulley.  
Slide belt into the center span keeper.  
Pull belt toward front of tractor and roll around the top  
groove of engine pulley.  
Install belt through stationary idler and clutching  
idler.  
Make sure belt is in all pulley grooves and inside all  
belt guides and keepers.  
Install mower (See “TO INSTALL MOWER” in this sec-  
tion of manual).  
If tractor requires more than five (5) feet to stop at highest  
speed in highest gear on a level, dry concrete or paved  
surface, then brake must be checked and adjusted.  
TO CHECK BRAKE  
Park tractor on a level, dry concrete or paved surface,  
depress clutch/brake pedal all the way down and en-  
gage parking brake.  
Place gear shift lever in neutral (N) position.  
Therearwheelsmustlockandskidwhenyoutrytomanually  
push the tractor forward.If the rear wheels rotate, the brake  
needs to be adjusted or the pads need to be replaced.  
ENGINE  
PULLEY  
TO ADJUST BRAKE  
Depress clutch/brake pedal all the way down and en-  
CLUTCHING  
IDLER  
gage parking brake.  
Measure distance between brake operating arm and  
nut “A” on brake rod.  
If distance is other than 1-1/2", loosen jam nut and turn  
nut “A” until distance becomes 1-1/2". Retighten jam  
nut against nut “A”.  
STATIONARY  
IDLER  
CENTER SPAN  
KEEPER  
Roadtesttractorforproperstoppingdistanceasstated  
above. Readjust if necessary. If stopping distance is  
still greater than five (5) feet in highest gear, further  
maintenance is necessary. Replace brake pads or  
contact a qualified service center.  
TRANSAXLE  
PULLEY  
WITH PARKING BRAKE “ENGAGED”  
1-1/2"  
NUT “A”  
FIG. 20  
JAM NUT  
OPERATING ARM  
FIG. 19  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
TRANSAXLE GEAR SHIFT LEVER NEUTRAL-  
ADJUSTMENT (See Fig. 21)  
WASHERS  
RETAINING  
RING  
The transaxle should be in neutral when the gear shift  
lever is in neutral (N) (lock gate) position. The adjustment  
is preset at the factory; however, if adjustment is needed,  
proceed as follows:  
AXLE  
COVER  
Make sure transaxle is in neutral (N).  
NOTE: When the tractor rear wheels move freely, the  
transaxle is in neutral.  
Loosen adjustment bolt in front of the right rear  
wheel.  
SQUARE KEY (REAR  
WHEEL ONLY)  
FIG. 22  
Position the gear shift lever in the neutral (N) posi-  
tion.  
TO START ENGINE WITH A WEAK BATTERY  
(See Fig. 23)  
Tighten adjustment bolt securely.  
NOTE: Ifadditionalclearanceisneededtogettoadjustment  
bolt, move mower deck height to the lowest position.  
WARNING: Lead-acid batteries gen-  
erate explosive gases. Keep sparks,  
flameandsmokingmaterialsawayfrom  
batteries. Always wear eye protection  
when around batteries.  
NEUTRAL  
LOCK GATE  
GEARSHIFT LEVER  
If your battery is too weak to start the engine, it should be  
recharged. (See "BATTERY" in the Maintenance section  
of this manual).  
If “jumper cables” are used for emergency starting, follow  
this procedure:  
IMPORTANT: YOURTRACTOR IS EQUIPPEDWITH A 12VOLT  
SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT  
SYSTEM. DO NOT USEYOUR TRACTOR BATTERY TO START  
OTHER VEHICLES.  
ADJUSTMENT  
BOLT  
FIG. 21  
TO ATTACH JUMPER CABLES -  
TO ADJUST STEERING WHEEL ALIGN-  
MENT  
If steering wheel crossbars are not horizontal (left to right)  
whenwheelsarepositionedstraightforward,removesteer-  
ing wheel and reassemble per instructions in the Assembly  
section of this manual.  
Connect one end of the RED cable to the POSITIVE  
(+) terminal of each battery(A-B), taking care not to  
short against tractor chassis.  
ConnectoneendoftheBLACKcabletotheNEGATIVE  
(-) terminal (C) of fully charged battery.  
Connect the other end of the BLACK cable (D) to good  
chassis ground, away from fuel tank and battery.  
FRONT WHEEL TOE-IN/CAMBER  
The front wheel toe-in and camber are not adjustable on  
yourtractor.Ifdamagehasoccurredtoaffectthefrontwheel  
toe-in or camber, contact your nearest authorized service  
center/department.  
TO REMOVE CABLES, REVERSE ORDER -  
BLACK cable first from chassis and then from the fully  
charged battery.  
RED cable last from both batteries.  
TO REMOVE WHEEL FOR REPAIRS  
(See Fig. 22)  
Block up axle securely.  
Removeaxlecover, retainingringandwasherstoallow  
wheel removal (rear wheel contains a square key - Do  
not lose).  
Repair tire and reassemble.  
On rear wheels only: align grooves in rear wheel hub  
and axle. Insert square key.  
Replace washers and snap retaining ring securely in  
axle groove.  
Replace axle cover.  
WEAK OR DEAD  
BATTERY  
FULLY CHARGED  
BATTERY  
FIG. 23  
NOTE: To seal tire punctures and prevent flat tires due to  
slow leaks, tire sealant may be purchased from your local  
parts dealer. Tire sealant also prevents tire dry rot and  
corrosion.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
TO REPLACE FUSE  
Replace with 20 amp automotive-type plug-in fuse. The  
fuse holder is located behind the dash.  
REPLACING BATTERY (See Figs. 24 and 25)  
WARNING: Do not short battery  
terminals by allowing a wrench or any  
other object to contact both terminals  
at the same time. Before connect-  
ing battery, remove metal bracelets,  
wristwatch bands, rings, etc.  
Positive terminal must be connected  
first to prevent sparking from acci-  
dental grounding.  
TO REMOVE HOOD AND GRILL ASSEMBLY  
(See Fig. 26)  
Raise hood.  
Unsnap headlight wire connector.  
Stand in front of tractor. Grasp hood at sides, tilt toward  
engine and lift off of tractor.  
To replace, reverse above procedure.  
Lift seat pan to raised position.  
DisconnectBLACKbatterycablerstthenREDbattery  
cable and carefully remove battery from tractor.  
HOOD  
Install new battery with terminals in same position as  
old battery.  
First connect RED battery cable to positive (+) terminal  
with hex bolt and keps nut as shown.Tighten securely.  
Slide terminal cover over terminal.  
HEADLIGHT WIRE  
CONNECTOR  
Connect BLACK grounding cable to negative (-) ter-  
minal with remaining hex bolt and keps nut. Tighten  
securely.  
01536  
SEAT PAN  
FIG. 26  
ENGINE  
TO ADJUST THROTTLE CONTROL CABLE  
The throttle control has been preset at the factory and  
adjustment should not be necessary. If adjustment is nec-  
essary, see engine manual.  
FIG. 24  
TERMINAL  
COVER  
KEPS NUT  
TO ADJUST CHOKE CONTROL  
The choke control has been preset at the factory and ad-  
justment should not be necessary. If adjustment is neces-  
sary, see engne manual.  
HEX  
BOLT  
TO ADJUST CARBURETOR  
Your carburetor is not adjustable. If your engine does not  
operate properly due to suspected carburetor problems,  
take your tractor to an authorized service center for repair  
and/or adjustment.  
POSITIVE (RED) CABLE  
NEGATIVE (BLACK) CABLE  
FIG. 25  
TO REPLACE HEADLIGHT BULB  
Raise hood.  
Pull bulb holder out of the hole in the backside of the  
grill.  
Replace bulb in holder and push bulb holder securely  
back into the hole in the backside of the grill.  
Close hood.  
INTERLOCKS AND RELAYS  
Loose or damaged wiring may cause your tractor to run  
poorly, stop running, or prevent it from starting.  
Check wiring. See electrical wiring diagram in the  
Repair Parts section.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STORAGE  
Immediately prepare your tractor for storage at the end  
of the season or if the tractor will not be used for 30 days  
or more.  
ENGINE  
FUEL SYSTEM  
IMPORTANT: ITISIMPORTANTTOPREVENTGUMDEPOSITS  
FROMFORMINGIN ESSENTIAL FUEL SYSTEM PARTS SUCH  
AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK  
DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT  
ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING  
ETHANOLORMETHANOL)CANATTRACTMOISTUREWHICH  
LEADSTOSEPARATIONANDFORMATIONOFACIDSDURING  
STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM  
OF AN ENGINE WHILE IN STORAGE.  
WARNING: Never store the tractor with  
gasoline in the tank inside a building  
where fumes may reach an open flame  
orspark. Allowtheenginetocoolbefore  
storing in any enclosure.  
TRACTOR  
Empty the fuel tank by starting the engine and let it run  
until the fuel lines and carburetor are empty.  
Never use engine or carburetor cleaner products in the  
fuel tank or permanent damage may occur.  
Removemowerfromtractorforwinterstorage. Whenmower  
istobestoredforaperiodoftime,cleanitthoroughly,remove  
all dirt, grease, leaves, etc. Store in a clean, dry area.  
Clean entire tractor (See “CLEANING” in the Mainte-  
nance section of this manual).  
Use fresh fuel next season.  
NOTE: Fuel stabilizer is an acceptable alternative in mini-  
mizing the formation of fuel gum deposits during storage.  
Add stabilizer to gasoline in fuel tank or storage container.  
Always follow the mix ratio found on stabilizer container.  
Run engine at least 10 minutes after adding stabilizer to  
allow the stabilizer to reach the carburetor. Do not empty  
the gas tank and carburetor if using fuel stabilizer.  
Inspect and replace belts, if necessary (See belt re-  
placement instructions in the Service and Adjustments  
section of this manual).  
Lubricate as shown in the Maintenance section of this  
manual.  
Be sure that all nuts, bolts and screws are securely  
fastened. Inspect moving parts for damage, breakage  
and wear. Replace if necessary.  
ENGINE OIL  
Touch up all rusted or chipped paint surfaces; sand  
lightly before painting.  
Drain oil (with engine warm) and replace with clean en-  
gine oil. (See “ENGINE” in the Maintenance section of  
this manual).  
BATTERY  
CYLINDER(S)  
Fully charge the battery for storage.  
Remove spark plug(s).  
After a period of time in storage, battery may require  
recharging.  
Pour one ounce of oil through spark plug hole(s) into  
cylinder(s).  
To help prevent corrosion and power leakage during  
long periods of storage, battery cables should be dis-  
connected and battery cleaned thoroughly (see “TO  
CLEAN BATTERY AND TERMINALS” in the Mainte-  
nance section of this manual).  
Turn ignition key to “STARTposition for a few seconds  
to distribute oil.  
Replace with new spark plug(s).  
After cleaning, leave cables disconnected and place  
cables where they cannot come in contact with battery  
terminals.  
If battery is removed from tractor for storage, do not  
store battery directly on concrete or damp surfaces.  
OTHER  
Do not store gasoline from one season to another.  
Replace your gasoline can if your can starts to rust.  
Rust and/or dirt in your gasoline will cause problems.  
If possible, store your tractor indoors and cover it to  
give protection from dust and dirt.  
Cover your tractor with a suitable protective cover that  
does not retain moisture. Do not use plastic. Plastic  
cannot breathe which allows condensation to form and  
will cause your tractor to rust.  
IMPORTANT: NEVERCOVERTRACTORWHILEENGINE AND  
EXHAUST AREAS ARE STILL WARM.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING POINTS  
PROBLEM  
CAUSE  
CORRECTION  
Will not start  
1. Out of fuel.  
1. Fill fuel tank.  
2. Engine not “CHOKED” properly.  
3. Engine flooded.  
4. Bad spark plug.  
5. Dirty air filter.  
2. See “TO START ENGINE” in Operation section.  
3. Wait several minutes before attempting to start.  
4. Replace spark plug.  
5. Clean/replace air filter.  
6. Dirty fuel filter.  
6. Replace fuel filter.  
7. Water in fuel.  
7. Empty fuel tank and carburetor, refill tank with fresh  
gasoline and replace fuel filter.  
8. Loose or damaged wiring.  
8. Check all wiring.  
9. Carburetor out of adjustment.  
9. See To Adjust Carburetor” in Service Adjustments  
section.  
10. Engine valves out of adjustment.  
10. Contact an authorized service center/department.  
Hard to start  
1. Dirty air filter.  
1. Clean/replace air filter.  
2. Bad spark plug.  
2. Replace spark plug.  
3. Weak or dead battery.  
4. Dirty fuel filter.  
3. Recharge or replace battery.  
4. Replace fuel filter.  
5. Stale or dirty fuel.  
6. Loose or damaged wiring.  
7. Carburetor out of adjustment.  
5. Empty fuel tank and refill tank with fresh, clean gasoline.  
6. Check all wiring.  
7. See To Adjust Carburetor” in Service Adjustments  
section.  
8. Engine valves out of adjustment.  
8. Contact an authorized service center/department.  
Engine will not turn over  
1. Clutch/brake pedal not depressed.  
2. Attachment clutch is engaged.  
3. Weak or dead battery.  
1. Depress clutch/brake pedal.  
2. Disengage attachment clutch.  
3. Recharge or replace battery.  
4. Replace fuse.  
4. Blown fuse.  
5. Corroded battery terminals.  
6. Loose or damaged wiring.  
7. Faulty ignition switch.  
8. Faulty solenoid or starter.  
9. Faulty operator presence switch(es).  
5. Clean battery terminals.  
6. Check all wiring.  
7. Check/replace ignition switch.  
8. Check/replace solenoid or starter.  
9. Contact an authorized service center/department.  
Engine clicks but will not  
start  
1. Weak or dead battery.  
1. Recharge or replace battery.  
2. Clean battery terminals.  
3. Check all wiring.  
2. Corroded battery terminals.  
3. Loose or damaged wiring.  
4. Faulty solenoid or starter.  
4. Check/replace solenoid or starter.  
Loss of power  
1. Cutting too much grass/too fast.  
2. Throttle in “CHOKE” position.  
3. Build-up of grass, leaves and trash under mower.  
4. Dirty air filter.  
1. Raise cutting height/reduce speed.  
2. Adjust throttle control.  
3. Clean underside of mower housing.  
4. Clean/replace air filter.  
5. Low oil level/dirty oil.  
6. Faulty spark plug.  
7. Dirty fuel filter.  
5. Check oil level/change oil.  
6. Clean and regap or change spark plug.  
7. Replace fuel filter.  
8. Stale or dirty fuel.  
9. Water in fuel.  
8. Empty fuel tank and refill tank with fresh, clean gasoline.  
9. Empty fuel tank and carburetor, refill tank with fresh  
gasoline and replace fuel filter.  
10. Spark plug wire loose.  
11. Dirty engine air screen/fins.  
12. Dirty/clogged muffler.  
10. Connect and tighten spark plug wire.  
11. Clean engine air screen/fins.  
12. Clean/replace muffler.  
13. Loose or damaged wiring.  
14. Carburetor out of adjustment.  
13. Check all wiring.  
14. See To Adjust Carburetor” in Service Adjustments  
section.  
15. Engine valves out of adjustment.  
15. Contact an authorized service center/department.  
Excessive vibration  
1. Worn, bent or loose blade.  
2. Bent blade mandrel.  
1. Replace blade. Tighten blade bolt.  
2. Replace blade mandrel.  
3. Loose/damaged part(s).  
3. Tighten loose part(s). Replace damaged parts.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING POINTS  
PROBLEM  
CAUSE  
CORRECTION  
Engine dies when  
tractor is shifted  
into reverse  
1. Reverse operation system  
(ROS) is not "ON" while  
1. Turn ignition key to  
ROS "ON" position.  
mower or other attachment  
is engaged.  
See Operation section.  
Engine continues to run  
when operator leaves seat  
with attachment clutch  
engaged  
1. Faulty operator-safety presence control system.  
1. Check wiring, switches and connections. If not  
corrected, contact an authorized service center/  
department.  
Poor cut - uneven  
1. Worn, bent or loose blade.  
2. Mower deck not level.  
1. Replace blade. Tighten blade bolt.  
2. Level mower deck.  
3. Buildup of grass, leaves, and trash under mower.  
4. Bent blade mandrel.  
3. Clean underside of mower housing.  
4. Replace blade mandrel.  
5. Clogged mower deck vent holes from buildup of  
grass, leaves, and trash around mandrels.  
5. Clean around mandrels to open vent holes.  
Mower blades will not  
rotate  
1. Obstruction in clutch mechanism.  
2. Worn/damaged mower drive belt.  
3. Frozen idler pulley.  
1. Remove obstruction.  
2. Replace mower drive belt.  
3. Replace idler pulley.  
4. Frozen blade mandrel.  
4. Replace blade mandrel.  
Poor grass discharge  
1. Engine speed too slow.  
2. Travel speed too fast.  
1. Place throttle control in “FAST” position.  
2. Shift to slower speed.  
3. Wet grass.  
4. Mower deck not level.  
3. Allow grass to dry before mowing.  
4. Level mower deck.  
5. Low/uneven tire air pressure.  
6. Worn, bent or loose blade.  
7. Buildup of grass, leaves and trash under mower.  
8. Mower drive belt worn.  
5. Check tires for proper air pressure.  
6. Replace/sharpen blade. Tighten blade bolt.  
7. Clean underside of mower housing.  
8. Replace mower drive belt.  
9. Blades improperly installed.  
10. Improper blades used.  
11. Clogged mower deck vent holes from buildup of  
grass, leaves, and trash around mandrels.  
9. Reinstall blades sharp edge down.  
10. Replace with blades listed in this manual.  
11. Clean around mandrels to open vent holes.  
Headlight(s) not working  
(if so equipped)  
1. Light switch is “OFF”.  
2. Bulb(s) or lamp(s) burned out.  
3. Faulty light switch.  
4. Loose or damaged wiring.  
5. Blown fuse.  
1. Turn light switch “ON”.  
2. Replace bulb(s) or lamp(s).  
3. Check/replace light switch.  
4. Check wiring and connections.  
5. Replace fuse.  
Battery will not charge  
1. Bad battery cell(s).  
1. Replace battery.  
2. Poor cable connections.  
3. Faulty regulator (if so equipped).  
4. Faulty alternator.  
2. Check/clean all connections.  
3. Replace regulator.  
4. Replace alternator.  
Engine “backfires” when  
turning engine “OFF”  
1. Engine throttle control not set between half and  
full speed (fast) position before stopping engine.  
1. Move throttle control between half and full speed  
(fast) position before stopping engine.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LIMITED WARRANTY  
The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materi-  
als and workmanship. For a period of two (2) years from date of purchase by the original consumer purchaser, we will repair or  
replace, at our option, without charge for parts or labor incurred in replacing parts, any part which we find to be defective due  
to materials or workmanship. This Warranty is subject to the following limitations and exclusions.  
1. This warranty does not apply to the engine, other than EHP manufactured transaxle/transmission components, battery (ex-  
cept as noted below) or components parts thereof. Please refer to the applicable manufacturer's warranty on these items.  
2. Transportation charges for the movement of any power equipment unit or attachment are the responsibility of the pur-  
chaser. Transportation charges for any parts submitted for replacement under this warranty must be paid by the purchaser  
unless such return is requested by Electrolux Home Products.  
3. Battery Warranty: On products equipped with a Battery, we will replace, without charge to you, any battery which we find  
to be defective in manufacture, during the first ninety (90) days of ownership. After ninety (90) days, we will exchange the  
Battery, charging you 1/12 of the price of a new Battery for each full month from the date of the original sale. Battery must  
be maintained in accordance with the instructions furnished.  
4. The Warranty period for any products used for rental or commercial purposes is limited to 90 days from the date of original  
purchase.  
5. This Warranty applies only to products which have been properly assembled, adjusted, operated, and maintained in accor-  
dance with the instructions furnished. This Warranty does not apply to any product which has been subjected to alteration,  
misuse, abuse, improper assembly or installation, delivery damage, or to normal wear of the product.  
6. Exclusions: Excluded from this Warranty are belts, blades, blade adapters, normal wear, normal adjustments, standard  
hardware and normal maintenance.  
7. In the event you have a claim under this Warranty, you must return the product to an authorized service dealer.  
Should you have any unanswered questions concerning this Warranty, please contact:  
In Canada contact:  
Electrolux Home Products, Inc.  
Electrolux Canada Corp.  
7075 Ordan Drive  
Mississauga, Ontario  
L5T 1K6  
Outdoor Products Customer Service Dept.  
1030 Stevens Creek Road  
Augusta, GA 30907 USA  
giving the model number, serial number and date of purchase of your product and the name and address of the authorized  
dealer from whom it was purchased.  
THIS WARRANTY DOES NOT APPLY TO INCIDENTAL OR CONSEQUENTIAL DAMAGES AND ANY IMPLIED WARRAN-  
TIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN FOR OUR EXPRESSED WARRANTIES. Some areas  
do not allow the limitation of consequential damages or limitations of how long an implied Warranty may last, so the above limi-  
tations or exclusions may not apply to you. This Warranty gives you specific legal rights, and you may have other rights which  
vary from locale to locale.  
This is a limited Warranty within the meaning of that term as defined in the Magnuson-Moss Act of 1975.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE  
®
®
POLICY  
WARRANTY  
Issued January 1980  
Revised January 1991  
LIMITED WARRANTIES  
FOR  
NEW PEERLESS GEAR POWER TRAIN COMPONENTS  
A. Products Warranted  
Peerless Gear and Machine Division of Tecumseh Products Company (“Tecumseh”), subject to the limitations contained below,  
will,at its option, repair or replace, without charge for parts or labor only, any part of a new Power Train Component (which as used  
herein means and includes the transaxle, gear box, transmission, differential and right angle drives, and any part of the Power Train  
Component), EXCEPT any new Power Train Component incorporated in equipment used for commercial or rental purposes, which is  
found upon examination by any Tecumseh Authorized Service Outlet or by Tecumseh’s factory in Grafton, Wisconsin, to be DEFECTIVE  
IN MATERIAL AND/OR WORKMANSHIP if received by Tecumseh or a Tecumseh Authorized Service Outlet for such examination within  
TWO YEARS from the date of sale to the original consumer purchaser of Peerless Series 820, 900, 910, 915, 920, 930 transaxles and  
Series 1100 angle drive and ONEYEAR for all other Peerless products. New Power Train Components incorporated in equipment used  
for commercial purposes are warranted in the same manner and to the same extent EXCEPT such Power Train Components are war-  
ranted for NINETY (90) DAYS ONLY, and must be received by Tecumseh or by a Tecumseh Authorized Service Outlet for such examina-  
tion within 90 days from the date of sale to the original purchaser. New Power Train Components Incorporated in equipment used for  
rental purposes are warranted in the same manner and to the same extent EXCEPT such Power Train Components are warranted for  
THIRTY (30) DAYS ONLY, and must be received by Tecumseh or a Tecumseh Authorized Service Outlet within 30 days from the date  
of sale to the original purchaser.  
B. Products And Items Not Warranted  
1. Alterations or Modifications of Power Train Components.  
2. Accidents, Normal Maintenance, Failure to follow the Original Equipment Manufacturer’s Manual.  
This warranty covers only parts of new Power Train Components which are found upon examination to be defective in material or  
workmanship as delivered to the original purchaser. This warranty does not cover defects caused by depreciation or damage caused  
by normal wear, accidents, improper maintenance, improper use or abuse of the product, failure to follow the instructions contained in  
an Instruction Manual for the operation of the Power Train Component and parts. The cost of normal maintenance and replacement of  
service items which are not defective shall be paid for by the original purchaser.  
C. Securing Warranty Service  
Warranty service can be arranged for by contacting either aTecumseh Authorized Service Outlet (anyTecumseh Registered Service  
Dealer, Tecumseh Authorized Service Distributor, or Tecumseh Central Warehouse Distributor) or by contacting Tecumseh, c/o Service  
Manager, Engine and Transmission Group Service Division, 900 North Street, Grafton, Wisconsin 53024. Warranty service can only  
be performed by a Tecumseh Authorized Service Outlet or by Tecumseh at its factory in Grafton, Wisconsin. At the time of requesting  
warranty service, evidence must be presented of the date of sale to the original purchaser. The purchaser shall pay any charges for  
making service calls and/or for transporting the product to and from the place where the inspection and/or warranty work is performed.  
The purchaser shall be responsible for any damage or loss incurred in connection with the transportation of Power Train Components  
and/or part(s) of the Power Train Components submitted for inspection and/or warranty work.  
D. Limitation of Damages and Implied Warranties  
The foregoing EXPRESSED WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES. Neither Tecumseh nor any of its  
affiliates makes any warranties, representations or promises, written or oral, as to the quality of the Power Train Component or any of  
its parts, other than as set forth herein.  
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, TO THE EXTENT THAT  
EITHER MAY APPLY TO ANY PART(S) OF POWER TRAIN COMPONENTS, SHALL BE LIMITED IN DURATION TO THE PERIODS  
OF THE EXPRESSED WARRANTIES DEFINED IN PARAGRAPH A HEREOF. IN NO EVENT WILL TECUMSEH BE LIABLE FOR ANY  
INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES AND/OR EXPENSES. Some states do not allow limitations on how long  
an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitation(s) or exclusion(s)  
may not apply to you. This warranty gives you specific legal rights and you may also have other legal rights which vary from state to  
state.  
E. No Dealer Warranty  
Tecumseh neither assumes nor authorizes any other person, natural or corporate, to assume for Tecumseh any other obligations or  
liabilities in connection with or with respect to any part(s) of a Power Train Component. The seller or dealer of part(s) of a Power Train  
Component has no authority, whatsoever, to make any representations or promises on behalf of Tecumseh or to modify the terms or  
limitations of Tecumseh’s warranty in any way.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION  
ONLY RIDE UP AND DOWN HILL,  
NOT ACROSS HILL  
15 DEGREES MAX.  
WARNING: To avoid serious injury, operate your tractor up and  
down the face of slopes, never across the face. Do not mow  
slopes greater than 15 degrees. Make turns gradually to prevent  
tipping or loss of control. Exercise extreme caution when  
changing direction on slopes.  
1. Fold this page along dotted line indicated above.  
2. Hold page before you so that its left edge is vertically parallel to a tree  
trunk or other upright structure.  
3. Sight across the fold in the direction of hill slope you want to measure.  
4. Compare the angle of the fold with the slope of the hill.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
®
PARTS AND SERVICE  
This product has been expertly engineered and carefully manufactured to rigid quality standards. As with all  
mechanical products, some adjustments or part replacement may be necessary during the life of your unit.  
For Parts and service, contact our authorized distributor: call 1-800-849-1297  
For replacement parts, have available the following information:  
a. Model Number/Manufacturer's I.D. Number  
b. Description of part.  
For Techical Assistance: call 1-800-829-5886  
NOTE: Electrolux Home Products provides parts and service through its authorized distributors and  
dealers; therefore, all requests for parts and service should be directed to your local dealer(s).  
The philosophy of Electrolux Home Products is to continually improve all of its products. If  
the operating characteristics or the appearance of your product differs from those described  
in this Manual, please contact your local dealer for updated information and assistance.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Bolens Lawn Mower 117 670A User Manual
Bolens Lawn Mower 607 User Manual
Cub Cadet Lawn Mower Z Wing 48 User Guide
Ferris Industries Lawn Mower 5900605 User Guide
Land Pride Lawn Mower 309 100M User Guide
McCulloch Lawn Mower 14592RB User Guide
Snapper Lawn Mower 8HP36 User Manual
Snapper Lawn Mower 306R User Manual
Weed Eater Lawn Mower 195013 User Guide
White Lawn Mower 134T696H190 User Guide