ST IG A P A RK
PRO 20
PRO 16
RO YAL
PRESIDEN T
CO MFO RT
EXCELLEN T
8211-0278-08
Download from Www.Somanuals.com. All Manuals Search And Download.
7
6
K
J
G
H
J
I
9
8
S
R
T
Q
11
10
C
D
E, F
A
B
3
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
ENGLISH
The machine may not be operated un-
less the engine casing is closed and
locked. Risk of burns and crushing in-
juries.
1 GENERAL
This symbol indicates WARNING. Per-
sonal injury and/or damage to property
may result if the instructions are not
followed carefully.
You must read these instructions and
the accompanying pamphlet “SAFETY
INSTRUCTIONS” carefully, before the
assembly begin.
2.3 Battery
Do not short circuit the battery’s termi-
nals. Sparks occur which can result in
fire. Do not wear metal jewellery which
can come into contact with the battery
terminals.
In the event of damage to the battery
casing, cover, terminals or damage to
the strip covering the valves, the bat-
tery should be replaced.
2 ASSEMBLY
The battery is a valve-regulated battery with 12 V
nominal voltage. The battery fluid does not need to
and cannot be checked or topped up. The only
maintenance that is required is charging, for exam-
ple after extended storage.
After charging the battery must be stored in a cool
place.
To avoid injury and damage to people
and property, do not use the machine
until all the measures in this instruction
have been carried out..
2.1 Accessories bag
The machine is supplied with a plastic bag contain-
ing components which shall be used during the as-
sembly. The bag contains (fig. 1):
The battery must be fully charged be-
fore being used for the first time. The
battery must always be stored fully
charged. If the battery is stored while
discharged, serious damage will occur.
Pos. No. Designation
Dimension
A
B
C
D
E
F
G
H
I
1
2
2
1
1
1
2
2
2
4
2
Drawing plate
Screw
8 x 20
Nut
M8
2.3.1 Charging with the engine
The battery can be charged using the engine’s gen-
erator as follows:
Tension pin
Shim washer
Shim washer
Shoulder washer
Screw
6 x 36
16 x 38 x 0.5
16 x 38 x 1.0
1. Install the battery in the machine as shown be-
low.
2. Place the machine outdoors or install an extrac-
tion device for the exhaust fumes.
3. Start the engine according to the instructions in
the user guide.
4. Allow the engine to run continuously for 45
minutes.
8 x 20
Knob
J
K
Washer
8.4 x 22 x 1.5
Screw, Comfort, President,
Excellentonly
Ignition key
L
2
5. Stop the engine. The battery will now be fully
charged.
2.2 Engine casing
2.3.2 Charging using battery charger
To inspect and maintain the engine and battery, re-
move the engine casing. Dismantling:
1. Unscrew the fuel cap/fuel gauge.
2. Pull up the rubber strap at the front edge of the
casing (fig. 2).
3. Carefully lift off the engine casing (fig. 3).
When charging using a battery charger, a battery
charger with constant voltage must be used.
Contact your dealer to purchase a battery charger
with constant voltage.
The battery can be damaged if a standard type bat-
tery charger is used.
2.3.3 Installing the battery
1. Open the engine casing and position the battery
in the appropriate place. See fig. 5.
2. Secure the battery in position.
3. First connect the red cable to the battery’s posi-
tive terminal (+).
Assembly:
1. Place the casing over the lip on each side.
2. Make sure that the pins on the rear edge of the
casing go down into the respective holes (fig. 4).
3. Secure the front edge of the casing with the rub-
ber strap (fig. 2).
4. Finally, screw in the fuel cap/fuel gauge.
4. Connect the black cable to the battery’s
negative terminal (-).
15
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
ENGLISH
If the cables are interchanged, the gen-
2.6 Arm rests (Pro20)
erator and the battery will be damaged.
See fig. 8, 9. The arm rests and the installation
components are supplied in a separate box. Assem-
ble as follows:
The engine must never be driven with
the battery disconnected. There is a risk
of serious damage to the generator and
the electrical system.
1. Assemble the left and right mounts onto the
seat. Use 3 screws (Q) supplied at each side.
2. Assemble the arm rests with screws (R), nuts
(S) and spacers (T).
3. Tighten the screws so that the arm rests simply
can be folded up/down.
2.4 Seat switch
(Comfort, President, Excellent)
See fig. 6. At the underside of the seat is a switch,
which plays an important role in the machine’s
safety system located.
Assemble the switch as follows:
1. Loosen the switch from the cables.
2. Assemble the switch at the underside of the seat
with the screws (K).
3. Reconnect the cables to optional pins at the
switch.
2.7 Steering wheel
See fig. 10. In order to minimise the axial play in
the steering column, the shim washers (E) and/or
(F) must be installed on the steering column be-
tween the steering column jacket and the bracket
as follows.
1. Install the steering column jacket on the steer-
ing column and secure by knocking in the ten-
sion pin (D) approximately 1/3 of its length.
2. Pull the steering column jacket and the steering
column up.
3. From the outside, check whether no washers,
the 0.5 mm washer, the 1.0 mm washer or both
washers can be inserted into the gap. The wash-
er/washers must not be forced in, as there must
be a little axial play.
4. Pull out the cotter pin and dismantle the steering
wheel jacket.
5. Install the washer/washers in accordance with
point 3 above.
2.5 Seat
See fig. 7. Install the mounting in the rear (upper)
holes as follows:
1. Install the shoulder washers (G) on the screws
(H).
2. Insert the screws through the slots in the brack-
et. Place a washer (J) between the seat and the
bracket.
3. Tighten the screws in the seat. Tightening
torque: 9±1.7 Nm.
If the screws are tightened more than
9±1.7 Nm, the seat will be damaged.
6. Install the steering column jacket on the steer-
ing column and secure by knocking in the ten-
sion pin fully. Use a counterhold.
4. Check that the seat moves easily in the slots in
the bracket.
2.8 Towing hitch
See fig. 11. Screw the towing hitch (A) into the two
holes on the underside of the rear axle using screws
(B+C). Tighten the screws properly.
Install the mounting in the front (lower) holes as
follows:
1. Install a washer (J) on each knob (I).
2. Insert the knobs through the slots in the bracket
and tighten by hand in the seat.
Tightening torque: 22 Nm.
3. Fold the seat down and place it in the desired
position.
4. Tighten the screw knobs (I) by hand.
2.9 Tyre pressure
Check the air pressure in the tyres. Correct air
pressure:
The screw knobs (I) and the seat will be
damaged if tools are used.
Front: 0.6 bar (9 psi)
Rear: 0.4 bar (6 psi)
The seat can be folded. If the machine is parked
outside when it is raining, fold the seat forward to
protect the seat cushion from getting wet.
2.10Accessories
For the installation of accessories, see separate in-
stallation guide supplied with each accessory.
Note: The cutting deck is regarded as an accessory
here.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Box 1006 SE-573 28 TRANÅS
GGP Sweden AB
·
·
Download from Www.Somanuals.com. All Manuals Search And Download.
|