MODEL SWZ
THIS MANUAL CONTAINS THE OPERATING
INSTRUCTIONS AND SAFETY INFORMA-
TION FOR YOUR SCAG MOWER. READING
THIS MANUAL CAN PROVIDE YOU WITH
ASSISTANCE IN MAINTENANCE AND AD-
JUSTMENT PROCEDURES TO KEEP YOUR
MOWER PERFORMING TO MAXIMUM EFFI-
CIENCY. THE SPECIFIC MODELS THAT THIS
BOOK COVERS ARE CONTAINED ON THE
INSIDE COVER. BEFORE OPERATING YOUR
MACHINE, PLEASE READ ALL THE INFOR-
MATION ENCLOSED.
PART NUMBER 03056
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
SUBJECT
PAGE
Introduction .................................................................................................. 1
General Safety Instructions.......................................................................... 1
Signal Words ............................................................................................... 1
Before Operating ......................................................................................... 2
While Operating........................................................................................... 2
Maintenance and Storage ........................................................................... 3
Initial Run-In Procedures ............................................................................. 4
Mower Operation ......................................................................................... 4
Cutter Deck Belt Adjustments ...................................................................... 5
Cutter Deck Adjustments ............................................................................. 6
Blade Height Adjustments ........................................................................... 6
Cutter Blades............................................................................................... 7
Neutral Adjustment ...................................................................................... 7
Steering Control Rod Adjustment ................................................................ 8
Tracking Adjustment .................................................................................... 8
Parking Brake .............................................................................................. 8
Lubrication and Maintenance Chart ............................................................ 9
Troubleshooting Cutting Conditions ............................................................ 10-12
Technical Specifications .............................................................................. 13-14
Notes .........................................................................................................................15
MEMBER
c
WE SUPPORT OPE
Equipment & Engine
Training Council
TECHNICIAN
CERTIFICATION
I
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
(CONTINUED)
SUBJECT
Illustrated Parts List
PAGE
SWM-36"Cutter Deck........................................................................ 16-17
SWM-48", 52", 61", 72" Cutter Decks...................................................... 18-19
Engine Deck................................................................................................ 20-21
Drive And Brake Components.................................................................. 22-23
Handle Assembly........................................................................................ 24-25
Hydraulic Assembly .......................................................................... 26-27
Hydraulic Pump Assembly................................................................ 28-29
Engine DeckWire Harness-Kohler (Single Cyl.) & 17KA................... 30
Engine Deck Wire Harness- Kohler Command V-Twin...................... 30
HandleWire Harness-Electric Start......................................................... 31
Wire HarnessW/Relay............................................................................... 31
Engine DeckWire Harness-14 Kawasaki............................................... 32
HandleWire Harness-Manual Start......................................................... 32
Replacement Decals.................................................................................. 33-35
Warranty Statement...............................................................Inside Back Cover
II
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
SIGNAL WORDS
Your mower was built to the highest standards in the
industry. However, the prolonged life and maxi-
mum efficiency of your mower depends on you
following the operating, maintenance and adjust-
ment instructions in this manual.
This symbol means “Attention! Become Alert!
Your Safety is Involved!" The symbol is used
with the following signal words to attract your
attention to safety messages found on the decals and
throughout this manual. The message that follows
the symbol contains important information about
safety. To avoid injury and possible death, carefully
read the message! Be sure to fully understand the
causes of possible injury or death.
We encourage you to contact your dealer for repairs.
All Scag dealers are informed of the latest methods
to service this equipment and provide prompt and
efficient service in the field or at their service shop.
They carry a full line of Scag service parts.
A replacement Operator's Manual is available from
your Scag Servicing Dealer or by contacting Scag
Power Equipment, Service Department, at P.O. Box
152, Mayville, WI 53050. Please indicate the
complete model and serial number of your Scag
product.
Signal Word:
It is a distinctive word on safety decals and through-
out this manual that alerts the viewer to the existence
and relative degree of the hazard.
USE OF OTHER THAN ORIGINAL SCAG
REPLACEMENT PARTS WILL VOID THE
WARRANTY.
The “Right” and “Left”, “Front” and “Rear” of the
machine are referenced from the operator’s perspec-
tive when in the normal operating position and
facing the forward travel direction.
The signal word “DANGER” denotes that an ex-
tremely hazardous situation exists on or near the
machine that could result in high probability of
death or irreparable injury if proper precautions are
not taken.
GENERAL SAFETY INSTRUCTIONS
WARNING:
READ THIS OPERATOR'S MANUAL and
instructions furnished with attachments.
The signal word “WARNING” denotes that a hazard
exists on or near the machine that can result in injury
or death if proper precautions are not taken.
Perform only those maintenance procedures de-
scribed in this manual. If major repairs are ever
needed or assistance is desired, contact an Author-
ized Scag Dealer. To ensure optimum performance
and safety, always purchase genuine SCAG replace-
ment parts and accessories.
CAUTION:
The signal word “CAUTION” is a reminder of
safety practices on or near the machine that could
result in personal injury if proper precautions are
not taken.
Your safety and the safety of others depends signifi-
cantly upon your knowledge and understanding of
all correct operating practices and procedures of this
machine.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
WHILE OPERATING
BEFORE OPERATING
1. Start the engine when the neutral latches are in
the neutral lock position, the cutter blades are
disengaged, the parking brake is on and the
speed adjustment lever is in the neutral position.
1. Know the controls and how to stop quickly.
2. Do not allow children to operate the machine.
Do not allow adults to operate the machine
without proper instruction.
2. Do not run the engine in a confined area without
adequate ventilation. Exhaust fumes are hazard-
ous and could possibly be deadly.
3. Remove all debris or other objects that might be
picked up and thrown by the cutter blades. Keep
all bystanders away from the mowing area.
3. Using the machine demands attention. To
prevent loss of control:
4. Keep all shields, safety devices, and decals in
place. If a shield, safety device or decal is
defective or damaged, repair or replace it before
operating. Also, check all nuts, bolts and screws
for proper tightness, to assure the machine is in
safe operating condition.
A. Mow only in daylight or when there is good
artificial light.
B. Watch for holes or other hidden hazards.
C. Do not drive close to a drop-off, ditch, creek
bank, or other hazard.
D. Reduce speed when making sharp turns and
when turning on hillsides.
E. Always be sure of your footing. Keep a firm
hold on the handles and walk---never run.
F. Do not operate where conditions are slippery.
5. Do not operate the machine while wearing
sandals, tennis shoes, sneakers or shorts. Also,
do not wear loose fitting clothing which could
get caught in moving parts. Always wear long
pants and substantial shoes. Wearing safety
glasses and safety shoes is advisable and required
by some local ordinances and insurance regula-
tions.
4. The discharge chute must always be installed and
in the down position on the side discharge cutter
deck except when the Scag optional grass
catcher or mulching plate are properly installed.
If the discharge area should plug, shut the engine
off and wait for all movement to stop before
removing the obstruction.
6. Fill the fuel tank with clean, fresh gasoline, with
a minimum octane rating of 87. Avoid spilling
gasoline. Gasoline is highly flammable, handle it
carefully.
5. Disengage the blades and wait for them to stop
before crossing gravel drives, walks or roads.
A. Use an approved gasoline container.
B. Do not fill the tank while the engine is hot or
running.
6. Shut the engine off and wait until the blades
come to a complete stop before removing the
grass catcher container.
C. Do not smoke while handling gasoline.
D. Fill the fuel tank outdoors and up to approxi-
mately 1" (25 mm) below the bottom of the
filler neck.
7. Never raise the cutter deck while the blades are
rotating.
E. Wipe up any spilled gasoline.
7. Before attempting to start the engine, move the
speed adjustment lever into the neutral position,
move the blade engagement switch to the OFF
position, apply the parking brake, and move the
neutral latches to neutral.
8. Always park the mower and/or start the engine
on a level surface. Apply the parking brake to
prevent the mower from moving when you are
not in the operator’s position.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
14. Use only Scag approved riding attachments.
9. Ifthecuttingbladesshouldstrikeasolidobjector
theequipmentshouldstarttovibrateabnormally,
stoptheengine,disconnectthesparkplugwire,and
check immediatelyforthecause. Vibrationis
generallyawarningoftrouble.Checkthemachine
fordamagedordefectiveparts. Repairanydamage
beforestartingtheengineoroperatingthecutter
deck. Besurethebladesareingoodconditionand
thebladeboltsaretight.
Scag Approved Riding Attachments:
RS-ZT
Using unapproved attachments, (especially
"stand-up" riding attachments) may be hazardous.
MAINTENANCE AND STORAGE
1. Disconnect the spark plug wire from the spark
plug to prevent accidental starting of the engine
when servicing, adjusting or storing the machine.
10. Reduce speed and exercise extreme caution on
slopes and in sharp turns to prevent tipping or
loss of control. Be especially cautious when
changing directions on slopes.
2. If the mower must be tipped to perform mainte-
nance or adjustment, remove the battery, drain
the gasoline from the fuel tank and the oil from
the crankcase.
WARNING:
DO NOT operate on steep slopes. To check a
slope, attempt to back up it (with the cutter deck
down). If the machine can back up the slope
without the wheels slipping, reduce speed and
use extreme caution. ALWAYS FOLLOW OSHA
APPROVED OPERATION.
3. To reduce potential fire hazard, keep the engine
free of excessive grease, grass, leaves and accu-
mulations of dirt.
4. Be sure the machine is in safe operating condi-
tion by keeping nuts, bolts, and screws tight.
Check the blade mounting bolts and nuts fre-
quently to be sure they are tightened.
11. Do not touch the engine or muffler while the
engine is running or soon after it is stopped.
These areas could be hot enough to cause a burn.
5. If the engine must be running to perform a
maintenance adjustment, keep hands, feet,
clothing and other parts of the body away from
the cutter deck blades and other moving parts.
12. Before leaving the operator’s position or leaving
the mower unattended, move the speed adjust-
ment lever into the neutral position, place the
neutral latches in the neutral lock position, apply
the parking brake, and move the blade engage-
ment switch to OFF. Shut the engine OFF and
remove the key.
6. Do not overspeed the engine by changing gover-
nor settings. To be sure of safety and accuracy,
have an authorized dealer check maximum
engine speed with a tachometer.
7. The engine must be shut off before checking the
oil or adding oil to the crankcase.
13. Do not pass or stand on the grass discharge side
of any mower with the engine running. Stop
operation when another person approaches.
8. Allow the engine to cool before storing the
mower in any enclosure such as a garage or
storage shed. Make sure the fuel tank is empty if
the machine is to be stored in excess of 30 days.
Do not store the mower near any open flame or
where gasoline fumes may be ignited by a spark.
WARNING
FALLING HAZARD
USE ONLY SCAG APPROVED
RIDING ATTACHMENTS
481109
SEE OPERATOR'S MANUAL
3
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Always store gasoline in a safety-approved, red
container.
MOWER OPERATION
1. Read and understand the safety instructions
before attempting to operate this machine.
10. Be careful when servicing the battery as it
contains acid, which is corrosive and could cause
burns to skin and clothing.
2. Before starting the engine:
* Check the oil level in the engine and the
hydraulic reservoir.
* Fill the fuel tank with clean, fresh, lead-
free gasoline.
11. Batteries release explosive gases when being
charged or discharged. Keep batteries away
from any source of sparks and/or flame.
* Open the fuel valve on the bottom of the
fuel tank.
12. Make sure all hydraulic connections are tight and
all hydraulic hoses and lines are in good condi-
tion before starting the machine.
-NOTE-
Use gasoline with an octane rating no less than
87.
13. Hydraulic fluid is under high pressure. If you
need service on your hydraulic system, please
see your authorized Scag dealer.
* The speed adjustment lever must be in
NEUTRAL.
* The blade clutch switch must be in the OFF
position.
* The neutral latches must be in the neutral
lock position.
INITIAL RUN-IN PROCEDURES
(FIRST DAY OF USE OR APPROXI-
MATELY 10 HOURS)
* The key switch must be on.
* The parking brake must be on.
1. Check the belts for proper tension at 2, 4 and 8
hours. Adjust as needed.
3. Start the engine:
2. Check the steering control rods and the speed
control for neutral adjustment. (See Adjust
ments, page 6-8)
* Choke as required. If the engine is cold, pull
the choke knob out. When the engine starts,
slowly push the choke in. If the engine
stalls, repeat the above operation. When the
engine is warm, choking may not be neces-
sary.
3. Check the tires for proper pressure.
Caster Wheels
Drive Wheels
25 psi.
15 psi.
4. Check for loose hardware. Tighten as needed.
5. Check the safety switches for proper adjustment:
4. Engage the cutter blades by pulling the blade
clutch switch into the ON position. Push the
switch to the OFF position to disengage the cutter
blades.
* The engine should crank and start if the
machine is in neutral, the PTO engage-
ment switch is OFF and the parking brake
is ON.
6. Apply lubricant to all the grease fittings. Lubri-
cant was applied at the factory. This is just a
precautionary check to make sure that all the
fittings have been lubricated.
PULL UP TO ENGAGE
PUSH DOWN TO DISENGAGE
390S0138
4
Download from Www.Somanuals.com. All Manuals Search And Download.
-NOTE-
When PTO is engaged or (possibly) disengaged,
a squealing sound from the underside of the
machine is normal. It is caused by the electric
clutch plates meshing as the mower comes up to
speed. For best equipment life, engage the
clutch with the engine at 1/2 throttle, not under
full load.
WARNING:
Dump Valve Levers
(normal position)
If you are not familiar with the operation of the
hydrostatic drive and zero turn feature, practice
turning and maneuvering with the hand controls
before engaging the blades.
SGB112
Figure 1. Dump Valves
5. Release the parking brake. Move the speed
adjustment lever to the desired mowing speed.
CUTTER DECK BELT ADJUSTMENTS
-NOTE-
-NOTE-
The hydro drive belt is spring loaded and does
not require adjustment.
Top speed is suggested only for transport!
6. Whilesqueezingthesteeringbrakeleverswithboth
hands,releasebothneutrallatches.
1. Remove the belt cover.
2. Adjust the cutter deck drive belt using a belt
tension gauge. Adjust the belt so that the belt
moves 1/2" with 10 pounds of pressure. Adjust
the tension by tightening or loosening the J-bolt
nut. (See figure 2)
7. When the steering brake levers are released, the
machinewilltravelstraight.Tomakearightturn,
squeezetheRHlever. Toturnleft,squeezetheLH
lever.
END OF L-SHAPED
8. TO STOP, squeeze both levers, lock the neutral
latches, and move the speed adjustment lever to
neutral.
BRACKET
BELT
"J" BOLT
NUT
9. To move the machine in reverse, squeeze up on
both steering control levers.
ire pressure canWbAeSHaEdRjusted for
10. To "freewheel" or move the machine around
without the engine running, turn the dump valve
levers located at the back of the pumps to the
"freewheel"positions(seeFigure1).Tooperatethe
machine,thedumpvalveleversmustbereturnedto
theclosedpositions.
CUTTER DECK DRIVE BELT TENSION
SC400G
ALIGNMENT IDLER - L.H.
Figure 2. Deck Drive Belt Adjustment
5
Download from Www.Somanuals.com. All Manuals Search And Download.
LOW CUT (1 3/4"- 3")
-NOTE-
Due to initial belt stretch and to prevent the belt
from slipping, check this adjustment after the
first 2 hours, 4 hours and 8 hours of operation.
MID RANGE
(2 1/2"- 3 3/4")
3. Adjust the RH blade drive belt using a belt
tension gauge. Adjust the belt so that the belt
moves 1/2" with 10 pounds of pressure. Adjust
thetensionbytighteningorlooseningtheJ-boltnut
(Seefigure3).
HIGH CUT (3 1/4"- 4 1/2")
4. Replace the belt cover.
CUTTER DECK HEIGHT ADJUSTMENT
SC405G
Nut Washer
Figure 4. Cutting Height Adjustment
Deck
Caster spacers also can be repositioned to change
cutting heights and to change the pitch of the deck.
(See figure 5)
"J" Bolt
PIN
SPACERS
Belt
Figure 3. Cutter Deck Belt Adjustment R.H.
CUTTER DECK ADJUSTMENTS
Due to the many cutting conditions that exist, it is
difficult to suggest a cutter deck setting that will
workforeverylawn. Therearetwoadjustmentsthat
can be made on these decks, pitch and height.
REPOSITIONING SPACERS
SC406G99
Figure 5. Caster Wheel Spacers
PITCH is the angle of the blades (comparing front to
rear). A 1/4" downward pitch (front of deck down)
is recommended for best cutting performance.
BLADE HEIGHT ADJUSTMENT
Adjusting the blade height can be done by moving
any number of the five smaller 1/4" spacers on the
blade mounting bolts to the top of the spindle shaft
or below the spindle shaft.
HEIGHT is the nominal distance the blade is off of
the ground. This measurement is made with the
blades pointed side to side and distance is measured
between cutting tip and ground. (Also see Blade
HeightAdjustment)
-NOTE-
All blades should be positioned equally.
Changes to the cutting height can be achieved by
repositioning the cutter deck. (This adjustment will
also effect the pitch of the deck). There are three
available positions (see figure 4).
For best cut and discharge, a minimum of three
spacersshouldbeinstalledbetweenthebladeandthe
spindle(Seefigure6).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ANGLE BLADE BACK
DO NOT CUT IN
X
X MUST NOT EXCEED
1/3 BLADE WIDTH
SC4O8G
30
Figure 7. Blade Sharpening
NEUTRAL ADJUSTMENT
1. Raise the drive wheels off the ground and block
the caster wheels.
2. Remove the speed control spring and the steer-
ing control rod from the machine. (See figure 8)
Steering Control
Rod
Bolts
SC407G
Spring
Bellcrank
Figure 6. Blade Spacers
Handle
SC160G
Figure 8. Neutral Adjustment
3. Loosen the wing nut and let the speed adjust-
ment bearing lever fall away from the cam.
CUTTER BLADES
4. Start the engine and observe the drive wheels. If
thedrivewheelsarerotating,loosentheboltsonthe
neutraladjustmenthandleandmovethehandleup
ordownuntilthewheelsareinneutral. (Seefigure
8)
Do not sharpen beyond 1/3 of the width of the blade.
(See figure 7)
-NOTE-
Dress the blade with a file. Using a wheel
grinder may burn the blade. Check the balance
of the blade. If blades are out of balance, vibra-
tion and premature wear of spindle assembly can
occur. See your authorized Scag dealer for
blade balancing or special tools, if you choose to
balance your own blades.
5. Tighten the bolts on the neutral adjustment
handle. When tightening the bolts, hold the
bellcrank to prevent it from moving and throw-
ing off the neutral adjustment.
6. Turn the engine off.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Tightenthebearingsecuringthespeedadjustment
bearingleverandrepeatontheoppositeside.
STEERING CONTROL ROD
ADJUSTMENT
4. With the machine on a flat level surface, start the
engine and place the speed adjustment lever into
the speed that will most often be used.
-NOTE-
This adjustment is made to allow the steering
control levers to be moved out of the neutral
latch without engaging reverse.
5. Squeeze the steering control levers and release
the neutral latch. Slowly release the steering
controllevers,allowingthemachinetomovefor-
ward.
1. Connect the steering control rods into the steer-
ing control levers on the handle. Do not install
the hair pin at this time.
6. If the machine pulls to one side, put the speed
adjustment lever back into the neutral position
and turn the engine off.
2. Turn the swivel joint on the steering control rods
until the swivel joint is centered in the slot in the
bellcrank.
7. On the side that the machine pulled toward,
loosen the wing nut securing the speed adjust-
ment bearing lever and move the bearing 1/16"
away from the cam. Start the engine and recheck
the tracking. Adjust as needed.
3. Remove the steering control rods from the
machine. Install the speed control spring onto
the swivel joint. Reinstall the steering control
rods onto the machine and secure using the hair
pins.
TRACKING ADJUSTMENT
8. If tracking cannot be achieved, contact your Scag
servicing dealer.
-NOTE-
Before proceeding with this adjustment, be sure
that the tire pressures are correct. (see page 4)
and that the neutral adjustment and the steering
control rod adjustment have been completed.
PARKING BRAKE
1. Adjusttheparkingbrakesothatwhenthebrake
hand lever is against the stop on the handle bar,
the brake levers on the brake shaft weldment are
against the stops on the engine deck.
1. Engage the neutral latch on both steering control
levers and move the speed adjustment lever into
the neutral position.
CAUTION:
2. Position the speed adjustment lever so that the
bearing just contacts the speed adjustment cam.
(See below)
Adjust the brake only enough to hold the
machine. Excessive force may cause damage
to the machine or brake components.
Speed Adjustment
Cam
Steering Control Rod
Swivel
2. Adjust the brake actuator rod on either side of
the machine to obtain proper brake adjustment.
Bearing
Joint
Speed
Adjustment
Bearing Lever
Bellcrank
Speed Control Spring
SC161G
8
Download from Www.Somanuals.com. All Manuals Search And Download.
LUBRICATION & MAINTENANCE
BREAK-IN
8 HOURS (DAILY)
+ Grease spindle until grease comes out the relief valve
Compatible Greases:
Lidok EP #2 (found at industrial shops)
Ronex MP (Exxon service stations)
Shell Alvania (Shell service stations)
Mobilux #2 (Mobil service stations)
Super Lub M EP #2 (Conoco service stations)
40 HOURS (WEEKLY)
100 HOURS (BIWEEKLY)
500 HRS OR ANNUALLY
PROCEDURE
COMMENTS
X
X
Check all hardware for proper tightness
Change engine oil and filter at 5 hours
Check engine oil
Remove debris from under belt cover
Sharpen cutter blades
Grease spindle bearings
Clean air filter
Check belt tension
Check tire pressure
X
X
X
X
X
X
X
Do not over fill
More often if needed
More often if needed
+ US Lithium MP White Grease 2125
More often if needed
Adjust as needed
Add or adjust as required
Adjust as needed
X
Check battery level
X
X
X
X
X
X
X
X
X
Replace air filter
More often if needed
Chassis grease
Chassis grease
Grease caster wheel bearings
Grease caster wheel pivot shafts
Grease idler pulley bracket on cutter deck
Change hydrostatic oil filter
Change engine oil and filter
Grease idler arm pivots
Chassis grease
Clean area before removing the filter
See engine manufacturer information
Chassis grease
Chassis grease
Chassis grease
Grease brake hand lever
Grease brake actuator levers
Check all hardware for proper tightness
Adjust air gap on electric clutch
Drain hydraulic system and replace oil
X
X
X
Contact your Scag dealer for information about
making this adjustment.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING CUTTING CONDITIONS
CAUSE
CURE
CONDITION
Stringers - Occasional
Blades of Uncut
Grass
Low engine RPM
Run engine at full 3600 RPM
Slow speed to adjust for conditions
Cut grass after it has dried out
Sharpen blades
Ground speed too fast
Wet grass
Dull blades, incorrect sharpening
Deck plugged, grass accumulation Clean underside of deck
Width of Deck
Belts slipping
Adjust belt tensions
SGB020
Streaking - Strips of
Uncut Grass in Cutting
Path
Dull, worn blades
Incorrect blade sharpening
Low engine RPM
Belt slipping
Sharpen blades
Sharpen blades
Run engine at full 3600 RPM
Adjust belt tension
Deck plugged, grass accumulation Clean underside of deck
Ground speed too fast
Wet grass
Slow speed to adjust for conditions
Cut grass after it has dried out
Replace blades
Width of Deck
Bent blades
SGB018
Streaking - Strips of
Uncut Grass Between
Cutting Paths
Not enough overlapping
between rows
Increase the overlap of each
pass
Width
of
Deck
Width
of
Deck
SGB019
10
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
CAUSE
CURE
CONDITION
Uneven Cut on Flat
Ground - Wavy
High-Low
Lift worn off of blade
Blade upside down
Replace blade
Mount with cutting edge toward
ground
Appearance,
Scalloped Cut, or
Rough Contour
Deck plugged, grass accumulation Clean underside of deck
Too much blade angle (deck pitch) Adjust pitch and level
Deck mounted improperly
Bent spindle area
Dull blade
See your authorized SCAG dealer
See your authorized SCAG dealer
Sharpen blade
Width of Deck
SGB020
Uneven Cut on
Uneven Ground -
Wavy Appearance,
Uneven ground
May need to reduce ground speed,
raise cutting height, and/or change
direction of cut
High-Low Scalloped
Cut, or Rough Contour
Width of Deck
SGB021
Sloping Ridge Across
Width of Cutting Path
Tire pressures not equal
Wheels uneven
Check and adjust tire pressure
Check and adjust tire pressure
See your authorized SCAG dealer
Deck mounted incorrectly
Width of Deck
SGB023
11
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
CAUSE
CURE
CONDITION
Scalping - Blades
Hitting Dirt or
Cutting Very Close to
the Ground
Low tire pressures
Ground speed too fast
Cutting too low
Check and adjust pressures
Slow speed to adjust for conditions
May need to reduce ground speed,
raise cutting height, change direction
of cut, and/or change pitch and level
Rough terrain
May need to reduce ground speed,
raise cutting height, and/or change
direction of cut
Ground speed too fast
Wet grass
Slow speed to adjust for conditions
Cut grass after it has dried out
Width of Deck
SGB022
Step Cut
Ridge in Center of
Cutting Path
Blades not mounted evenly
Bent blade
Adjust pitch and level
Replace blade
Internal spindle failure
Mounting of spindle incorrect
See your authorized SCAG dealer
See your authorized SCAG dealer
Width of Deck
SGB024
Slope Cut - Sloping
Ridges Across Width
of Cutting Path
Bent spindle mounting area
Internal spindle failure
Bent deck housing
See your authorized SCAG dealer
See your authorized SCAG dealer
See your authorized SCAG dealer
Width of Deck
SGB025
12
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL SPECIFICATIONS
ENGINES
General Type:
Brand:
Heavy duty industrial/commercial
Kohler, Kawasaki,
Models:
Horsepower:
Type:
Kohler CV15T, CVE 20;Kaw. FC420V;
Kohler 15HP& 20HP; Kaw. 14HP; Kaw. 17HP
4 cycle gas, vertical shaft engines
Displacement:
Kohler: 15HP = 426cc, 20 HP= 624cc
Kawasaki: 14HP = 423cc, 17HP = 494cc
Varied - see manufacturer's specifications
Mechanical type governor with variable speed control set
at 3600 rpm (+75 rpm), idle set at 1200 rpm (+75 rpm)
Single exhaust canister muffler
Varied - See manufacturer's specifications
Varied - See manufacturer's specifications
Varied - See manufacturer's specifications
Electronic Ignition with recoil starter or 12 volt battery with
alternator, solid state ignition with key start
15 amp
Cylinders:
Governor:
Exhaust Group:
Fuel Pump Group:
Oil Pump Group:
Valve Group:
Starter/Electrical:
Charging System:
ENGINE DECK
Thickness:
7 gauge steel
Fuel Tank:
Drive Wheels/Tires:
Brakes:
5 gallon (19.0 litres) seamless polyethylene
16x6.50-8 four-ply pneumatic tubeless, radius edge
Dynamic braking through hydro drive system
1" tapered
Axles:
Handle Bars:
1-1/4" diameter
DRIVE SYSTEM
Type:
Hydro drive with two variable displacement pumps and two
cast-iron high torque motors
Hydro Pumps:
Two Hydro-Gear Model BDP 10L pumps with dump valves for
movement without running the engine
Drive Wheel Motors:
Hydro Fluid Cooling Group:
Two 12 cu. inch cast-iron high torque motors
Heavy-duty cooling radiator, 7 qt. capacity cooling
reservoir, uses, SAE 10W30 fluid and 10 micron filter
Independent handle controls for each wheel, squeeze to move
from forward to neutral to reverse, neutral lock lever, speed
range controlled with single lever (patented design), in-field
tracking adjustment with no tools necessary
7.5" drum, band brake, one on each wheel
Steering / Travel Control::
Parking Brakes:
Dump Valves:
Axles:
Allows for movement without engine running
1" tapered motor shafts
Wire Harness:
Safety Group:
14 gauge wire
Handle actuated operator presence system (patented design),
blade / clutch and transmission interlock to engine kill
Forward Speed Range:
Reverse Speed Range:
0 to 7.4 mph
0 to 3.0 mph
Date of Issue: May, 1998
Specifications Subject to Change Without Notice
13
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL SPECIFICATIONS (CON'T)
CUTTER DECKS
Type:
Construction:
SWM 36, SWM 48, SWM 52, SWM 61, SWM 72
Out-front design with anti-scalp rollers
SWM36,48: 7-gauge steel with 7-gauge (3/16") steel skirt
SWM52,61,72:10-gauge steel with 7-gauge (3/16") steel
skirt
Cutting Width:
35.5" (90.2 cm), 48.0 (122.0 cm), 52.0 " (132.0 cm),
61.0 " (155.0 cm), 71.5" (181.6 cm)
Cutting Height Adjustment:
Cutter Blades:
Adjustable from 1-3/4" to 4-1/4" in 1/4" increments
.204 thick, milled edge, 5150 alloy steel
SWM 36: Two (2) 18" SWM 48: Three (3) 16.5"
SWM 52: Three (3) 18" SWM 61: Three (3) 21"
SM72: Three (3) 24" blades
Blade Engagement:
Discharge Opening:
Electric blade brake clutch with instrument panel switch
Extra wide 11.5", 13.75 " discharge opening with hinged
chute
Caster Wheels:
Spindles:
9.4 x 3.5 smooth tread flotation, inner tubes, split rims, roller
bearings, with quick pin removal
Cast housing, taper roller bearing, low maintenance with
top access grease fitting and grease overfill relief poppet
Cast-iron with easily removed taper hubs
5" diameter pulley, welded and riveted construction,
1-3/8" O.D. Bearing
Spindle Pulleys:
Idler Pulley:
Idler Arm:
Cutter Deck Belts:
Heavy duty idler arm of 1/4" channel steel
B-section with Kevlar cord
ADDITIONAL SPECIFICATIONS
OPTIONAL ITEMS/ATTACHMENTS
Fabric Grass Catcher:
Metal Grass Catcher:
GC-F4 Grass Catcher with 4 cubic ft. capacity
GC-4D Grass Catcher with 4 cubic ft. capacity and rope pull
dump or pick-up and dump
Steerable Sulky:
Mulching Plate:
RS-ZT Steerable Sulky with padded seat and full articulation
for zero-radius turning
Steel plate fits over discharge opening. No blade change or
or removal required. Installs and removes in the field.
APPROXIMATE DIMENSIONS
Length:
Length with Grass Catcher:
Tracking Width:
SWM36 SWM48 SWM52 SWM61 SWM72
74.0"
74.0"
37.0"
54.5"
37.5"
55.0"
40.5"
40.5"
74.0"
74.0"
42.0"
60.0"
53.0"
69.0"
40.5"
40.5"
74.0"
74.0"
42.0"
60.0"
53.0"
69.0"
40.5"
40.5"
590 lbs.
630 lbs.
Zero
76.0"
76.0"
42.0"
70.0"
63.0"
80.0"
40.5"
40.5"
625 lbs.
665lbs.
Zero
76.0"
76.0"
42.0"
81.0"
74.0"
91.0"
40.5"
40.5"
695lbs.
730 lbs.
Zero
Width:
Width (with discharge chute up):
With with grass catcher:
Height:
Height with grass catcher:
Weight
510 lbs. 550 lbs.
550 lbs. 590 lbs.
Weight with grass catcher:
Turning Radius:
Zero
Zero
Date of Issue: May, 1998
Specifications Subject To Change Without Notice
14
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
15
Download from Www.Somanuals.com. All Manuals Search And Download.
36" CUTTER DECKS
9
41
69
40
47
61
45
44
43
44
45
68
11
43
59
58
11
41
69
46
46A
57
22
53
60
42
A
41
39
58
42
39A
48
50
54
55
7
14
13
37
56
49
52
38
18
36
51
49
A
2
19
37
35
14
20
21
55
40
22
21
20
8
1
1A
14
23
25
24
27
62
28
26
35
5
10
66
22
6
29
34
32
31
33
11
3
4
12
11
30
64
63
31
15
15A
5
16
67
65
17
SW-SWZ99CD36
16
Download from Www.Somanuals.com. All Manuals Search And Download.
36" CUTTER DECKS
Ref. Part
Ref. Part
No. Number Description
No. Number Description
45
46
47
48
04020-09
48204
43077
Hex Nut, 5/8-11
Belt, Blade Drive
Spacer
1
2
3
4
5
6
7
8
461131
46631
43312
48307-08
481022
43294
Cutter Deck (Includes Decals)
Cutter Spindle Assy.
Spacer, Outside
Tapered Nut, 5/16-24
Tapered Bearing (Two)
Spindle Housing
04021-05
Hex Nut, 3/8-16 Center Locknut
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
69
04019-04
04004-02
04017-42
04019-05
43277
04041-12
04021-09
45423
Nut, 3/8-16 Serrated Flange
Support, Belt Cover
Cpscrw, 7/16-14 x 1"Ser.Flg. HH
Nut, 7/16-14 Serrated Flange
Spacer, J-Hook
Washer, 3/8 x 1-1/2 x 16 GA
Elastic Stop Nut, 3/8-16
Idler Pivot
Idler Arm Assy. (Inc. 22 & 58)
Bronze Bearing
Retaining Ring, 1-1/8" Ext. ”E”
J-Hook
Idler Pulley, Belt Clutch
Seal, Cutter Spindle
Spindle Bushing
Spacer, Inside
Nut,
04001-108 Bolt, 5/16-18 x 4-1/4" Hex Head
43298 Spindle Shaft
04001-77 Bolt, 3/8-16 x 3-1/2" Hex Head
04063-08
43278
04001-10
481050
04019-03
48108
9
10
11
12
13
14
15
Key, 1/4 x 1/4 x 2"
Spacer, Cutter Blade - Small
Bolt,5/16-18 x 1-1/4" Hex Head
Spring, Chutte Return
Nut 5/16-18 Serrated Flange
Cutter Blade, 18"
Cutter Blade, 18 Hi Lift
Flatwasher, 5/8 W
Hex Hd. Bolt, 5/8-11 x 9-1/2"
Caster Assembly (Inc.19-28)
Quick Pin
Spacer, Caster Yoke, 1/2" long
Bronze Bearing
Grease Fitting
Support Assembly (Inc. 21-23)
Caster Yoke
46748
48100-02
04050-05
44078
48269
481024
43297
43296
481035
48677
481025
48098
04029-04
15A 48185
16
17
18
19
20
21
22
23
24
25
26
27
28
29
04040-10
04001-41
46079
04066-01
43037-01
48100-01
48114-04
46082
45006
43022
04001-37
04021-07
48307
Relief Fitting, Cutter Spindle
Seal, Cutter Spindle
SpindleShield
Wing Nut, 3/8-16 (Small) Top Side
Wing Nut, 3/8-16 (Small) RH Side
04029-04
Sleeve, Caster Wheel Bearing
Hex Hd. Bolt, 1/2-13 x 5-1/2"
Elastic Stop Nut, 1/2-13
Wheel Assy. (Inc.4, 29-34)
Tire only, Caster Wheel
Inner Tube only
48307-02
NS 48006-03
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
48307-04
48006-07
48006-06
48114-03
48006-05
04017-16
461054
04021-10
04001-09
46797
04041-07
04029-03
48924
48926
04001-01
Rim Pair, Caster Wheel
Retainer, Bearing, Caster Wheel
Roller Bearing, Caster Wheel
Grease Fitting, 45 degree 1/4-28
Hub Assembly
Cpscrw,5/16-18 x 3/4" Ser.Flg. Hex Head
Discharge Chute
Hex Nut, 5/16-18 Elastic Stop
Hex Hd Bolt, 5/16-18 x 1"
Belt Cover Assy (Includes Decal)
Flat Washer, 3/8" Special
Wing Nut, 3/8-16
Pulley
Tapered Hub
Hex Hd. Bolt, 1/4-20 x 3/4"
* Common hardware which should be purchased locally. All bolts are Grade 5 plated, all other fasteners zinc
plated.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
48", 52", 61", & 72" CUTTER DECKS
41
73
59
51
40
22
39
44
56, 56A
61
45
11
45
44
43
7
51
58
60
44
45
48
43
11
47
4
40
11
43
41
46
62, 62A
63
64
65
9
74
61
14
46A
46B
40
63
76
41
49
82
37
78
77
42
42A
42B
52
50
67
13
38
7
36
A
18
55
36A
54
14
57
68
64
51
51
40
77
14
75
35
50
19
37
A
20
21
35
7
21
20
8
35
14
79
2
25
26
23
24
27
66
1
28
80
5
10
53
69
7
6
29
11
34
33
70
32
12
11
31
83
3
30
15
15A
5
31
16
71
81
72
17
SW-SWZ99CD48"
18
Download from Www.Somanuals.com. All Manuals Search And Download.
48, 52, 61, & 72" CUTTER DECKS
Ref. Part
No. No.
Ref. Part
No. No.
Description
48 52 61 72
Description
48 52 61 72
44 04001-01
45 04020-09 Nut, 5/8-11 Hex
Bolt, 1/4-20 x 3/4" Hex Head
x
x
x
x
x
x
x
x
x
x
1
461132
Cutter Deck (Includes decals)
x
1
1
1
2
3
4
5
6
7
8
9
461134
461138
46608
46631
43296
48924
481022
43294
Cutter Deck (Includes decals)
Cutter Deck (Includes decals)
Cutter Deck (Includes decals)
Spindle Assembly
Spacer, Inside
Pulley
x
x
x
46 48923
46A 48940
46B 48966
47 48087
47 48285
47 48265
47 48295
48 48089
48 48286
48 48088
48 48296
Pulley, Double
Pulley, Double
Pulley, Double
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
Belt, RH Blade Drive
Belt, RH Blade Drive
Belt, RH Blade Drive
Belt, RH Blade Drive
Belt, Blade Drive
Belt, Blade Drive
Belt, Blade Drive
Belt, Blade Drive
x
x
x
x
Tapered Bearing (Two)
Spindle Housing
48114-04 Grease Fitting Str. 5/16
43298
45037
Spindle Shaft, Tapered Brng
Idler Pivot
x
x
x
x
x
x
x
x
x
x
x
x
x
x
10 04063-08 Key, 1/4 x 1/4 x 2"
11 43278
12 04001-10 Bolt, 5/16-18 x 1-1/4" Hex Head
13 04001-108 Bolt, 5/16-18 x 4-1/4" Hex Head
14 04019-03 Serrated Flange Nut, 5/16-18
15 48110
15 48108
15 48111
15 48112
15A 48184
15A 48185
15A 48304
16 04040-10
17 04001-41
18 46079
19 04066-01 Quick Pin
20 43037-01 Spacer, Caster Yoke, 1/2" thick
21 48100-01 Bronze Bearing
22 48098
23 46082
24 45006
25 43022
26 04001-37 Hex Hd Bolt, 1/2-13 x 5-1/2"
27 04021-07 Elastic Stop Nut, 1/2-13
28 48307
29 48307-02 Tire only, Caster Wheel
NS 48006-03 Inner Tube only, Caster Wheel
30 48307-04 Rim Pair, Caster Wheel
31 48006-07 Bearing Retainer, Caster Wheel
32 48006-06 Roller Bearing, Caster Wheel
33 48114-03 Grease Fitting 45 deg., 1/4-28
34 48006-05 Hub Assembly, (incl. bolts)
35 04017-16 Capscrew, 5/16-18 x 3/4"
36 461055
36A 461054
37 04021-04 Nut, 5/16-18 Elastic Elastic Stop
38 04001-09 Bolt, 5/16-18 x 1" Hex Head
39 46798
39 461095
39 46804
39 46805
39 46848
40 04041-07 Flat Washer, 3/8" Special
41 04029-03 Wing Nut, 3/8-16 (Large)
42 48924
42A 48753
42B 48967
43 48926
49
04021-05 Nut, 3/8-16, Nut Centerlock
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
Spacer, Cutter Blade - Small
50 04019-04 Nut, 3/8-16, Serrated Flange
51 04021-09 Nut, 3/8-16 Elastic Stop
52 04004-02 Support, Belt Cover
53 04001-08 Bolt, 5/16-18 x 1/2" Hex Head
54 04017-42 Cpscrw,7/16-14 x 1"Ser Flng H Hd x
55 04019-05 Nut, 7/16-14 Serrated Flange
56 04041-08 Flat Washer 3/4" Special
56A 04041-08S Flat Washer 3/4" Special
57 44078
58 48181
59 04050-02 Retaining Ring, 3/4" Ext.”E”
60 46081 Idler Arm Assy. (Incl. 7 & 61)
61 48100-05 Bronze Bearing
62 43028
62A 44078
63 43077
Cutter Blade 16-1/2"
Cutter Blade 18"
Cutter Blade 21"
Cutter Blade 24"
Cutter Blade 16-1/2 Hi Lift
Cutter Blade 18 Hi Lift
Cutter Blade 21 Hi Lift
Flatwasher,5/8" (.688 x 1.75 x .134)
Hex Head Bolt, 5/8-11 x 9-1/2"
Caster Assembly, (incl.19-28 & 7)
x
x
x
x
x
x
x
x
x
x
x
J-Hook
Idler Pulley, “V” Groove
x
x
x x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
J-Rod, Idler Pulley
J-Rod, Idler Pulley
Spacer, J-Rod
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
64 04041-12 Washer, 3/8 x 1-1/2 x 16 ga.
65 04001-46 Bolt, 3/8-16 x 2-1/4" Hex Head
SpindleShield
Support Assembly, (incl. 21-23)
Caster Yoke
Sleeve, Caster Wheel Bearing
66 481024
67 46748
68 43277
69 48677
70 43312
71 43297
72 481035
73 04029-04
74 04001-77
75 45329
76 48269
77 48100-02 Bronze Bearing
78 04050-05 Retaining Ring
Seal, Cutter Spindle
Idler Arm Assy (Includes 22&77)
Spacer, J-Rod
Reiief Fitting, Cutter Spindle
Spacer, Outside, Cutter Spindle
Spindle Bushing
Nut, Cutter Spindle
Wing Nut, 3/8-16 (Small) Top Side
Bolt, 3/8-16 x 3-1/2" Hex Head
Idler Pivot
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
Wheel Assy. (incl. 29-34,81)
Idler Pulley, Belt Clutch
79 48038
80 45944
81 481025
82 481050
83 48307-08
Guide Roller
Roller Shaft
Seal, Cutter Spindle
Spring,ChuteReturn
Nut,3/8-24Tapered
Discharge Chute
Discharge Chute
x
x
x
x
x
x
x
x
x
x
x
Belt Cover (Includes decals)
Belt Cover (Includes decals) 17KA x
Belt Cover (Includes decals)
Belt Cover (Includes decals)
Belt Cover (Includes decals)
x
x
x
x
x
x
x
x
x
x
x
x
x
Pulley
Pulley
Pulley
Tapered Hub
x
x
x
x
x
x
19
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGINE DECK
5
7
55
4
6
58
48
2
7
1
53
50
51
8
18
16
3
17
38
16
61
BLK
60
RED
9
10
37
11
45
33
63
11A
ELECTRIC
START ONLY
34
34A
32
12
12A
56
65
43
42
45
15
13
11
14
20
23
19
57
22
21
54
59
35
49
38
39
38
64
62
35
40
47
47A
27
39
41
45
43
28
44
26
45
43
25
29
24
38
46
43
30
31
030441698
20
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGINE DECK
Ref. Part
No. No.
Ref. Part
No. No.
Description
14KA 15KH 17KA 20CVE
Description
14KA 15KH 17KA 20CVE
1
1
1
1
2
3
4
5
6
7
8
9
10
11
48842
Engine 14KA Kawasaki
Engine 15KH Kohler
Engine 17KA Kawasaki
Engine 20CVE Kohler Command
x
x
x
x
41
42
43
44
45
46
47
04001-08 Hex Head Bolt, 5/16-18 x .75"
04040-14 Flat Washer 1/4"
04021-10 Nut, 5/16-18 Elastic Stop
04003-04 Carrage Bolt, 5/16-18 x 1"
48030-09 Clamp
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
48844
481066
48971
04050-10 Retaining Ring, 1/2" Ext. "E"
04020-02 Hex Nut, 1/4-20
04010-10 Screw, 1/4-20 x 2" Rnd. Hd. Phil.
421239
481603
48292
46846
48309
48308
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
421370
Clutch Bracket
04017-19 Capscr, 5/16-18 x 1.50" Sr. Flg.
Strap, Fuel Tank
Cap, Fuel Tank
Pad, Rubber-Fuel Tank - Upper
Fuel Tank Assy. (incl. 9, 10)
Bushing
47A 04002-01 Metric HH Bolt, M8-1.25 x M30
x
x
x
x
x
x
x
x
48
49
50
51
52
53
54
54
55
56
57
58
59
60
61
62
63
64
65
04031-09 Lock Washer, 5/16 Int. Tooth
04030-03 Lock Washer, 5/16
x
48257
Pipe Cap
x
x
48402-04 Pipe, 4.75" Nipple
04003-09 Carrage Bolt, 1/4-20 x 1-1/4"
Valve, Fuel Shut-off
x
x
48059-01 Clamp, Fuel Hose
481717
45418
45419
45283
421390
Wire Hrns. Adapter, 17KA
Pulley Guard, 16" Frame
Pulley Guard, 20" Frame
Shaft Weldment, RH Pump Cntl.
Bracket, Capacitor
x
11A 48059-02 Clamp, Fuel Hose, (KA Only)
12
12A 48058
x
x
48058
Fuel Hose, 1/4 ID x 20" KA
Fuel Hose, 1/4 ID x 23"
x
x
x
x
x
x
x
x
x
x
x
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
48028-05 Cable Tie
48057-02 Fuel Filter
48179 Fuel Hose, 7/32 ID x 3-1/2"
04015-06 Capscrew, #10-32 x 1 Soc. Hd.
46323
46324
48015
04001-44 Bolt, 1/4-20 x .50"
04020-02 Nut, 1/4-20
48099
42392
04029-01 Wing Nut, 1/4-20
45685
48661
04003-01 Bolt, 1/4-20 x 6" Carriage
04003-28 Carriage Bolt, 5/16-18 x 2"
04003-04 Carriage Bolt, 5/16-18 x 1"
422553
422552
x
x
x
x
x
x
x
x
21013-2064 Condenser (order from Kaw. )
04002-07 Metric H H Bolt, 8-1.25 x 10
21066-2071 Regulator, (order from Kaw.)M
48029-02 Battery Cable, 31.5" Red
48029-14 Battery Cable, 31.5 Black
x
x
x
x
x
x
x
x
Lever Assy., Pump Control -LH
Lever Assy., Pump Control -RH
Battery
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
421703
48126
Battery Box
Rubber Boot
04003-12 Carrage Bolt, 5/16-18 x .75
48030-10 Cable Clamp, .75 ID
Pad
Battery Cover
x
Battery Support
Pad, Rubber
x
x
x
x
x
x
x
x
x
x
x
x
x
x
Stiffener
Plate, Backing
04021-08 Nut, 1/4-20 Elastic Stop
48205
46946
x
x
x
x
x
x
x
x
Pad, Rubber-Fuel Tank, Lower
Engine Deck, 16" Wide, W/Decls.
Engine Deck, 20" Wide, W/Decls.
34A 46947
x
x
x
x
x
x
x
35
36
37
38
39
40
04003-09 Bolt,1/4-20 x 1-1/4" Hex Head
04019-02 Nut, 1/4-20 Serrated Flange
04017-18 Capscr., 5/16-18 x 1.25 Sr. Flg.
04019-03 Nut, 5/16-18 Serr. Flange
04019-04 Nut, 3/8-16 Serr. Flange
x
x
x
x
x
x
x
x
x
04001-22 Bolt, 3/8-16 x 2-3/4" Hex Head
21
Download from Www.Somanuals.com. All Manuals Search And Download.
DRIVE AND BRAKE COMPONENTS
1
2
3, 3A
5
4
7
8
9
6
10, 10A
7
A
A
49
2
53
11
47
43
44
51
42
42
41
50 52
48
49
4
45
46
2
11
50
40
7
39
38
48
12
13
36
47
21
20
35
14
15
1
37
19
34
24
24A
18
33
25
26
16
23
17
22
32
27
28A
28B
28C
SWZ99D&BC
29
30
31
22
Download from Www.Somanuals.com. All Manuals Search And Download.
DRIVE AND BRAKE COMPONENTS
Ref. Part
No. No.
Ref. Part
No. No.
Description
14KA 14KH 17KA 20CVE
Description
14KA 14KH 17KA 20CVE
28A 04002-05 Hex Head Bolt, M10-1.5 x 65
28B 04001-149 Hex Head Bolt, 7/16-20 x 2.00"
x
x
1
2
3
3A
4
5
6
7
04050-02 Retaining Ring, 3/4 Ext. "E"
04001-19 Bolt, 3/8-16 x 1" Hex Head
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
45842
45854
Brake Shaft Assy. Wlmt.Small
Brake Shaft Assy. Wlmt.Large
29
30
31
32
33
34
35
36
37
38
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
422534
48030-09 Clamp
04021-10 Nut, 5/16-18 Elastic Stop
481716
422533
Plate, Backing
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
04062-01 Hair Pin Cotter, .094 x 1.62
04003-12 Carrage Bolt, 5/16-18 x .75"
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
Rubber Pad, Clutch Stop
Retainer, Clutch Stop
44126
04019-04 Nut, 3/8-16 Serr. Flange
43415 Bushing, Brake
48114-05 Grease Fitting
45860 Brake Actuator Wlmt., LH
Brake Actuator Wlmt., RH
04001-46 Bolt, 3/8-16 x 2-1/4"
481618 Tire, 16 x 6.50, 4 ply
48004-04 Rim Assy
Rod, Brake Lower
04001-12 Hex Head Bolt, 5/16-18 x 1.75"
481665 Pulley, Pump Drive Engine
8
9
10
04001-13 Hex Head Bolt, 5/16-18 x 2.75"
04021-05 Nut, 3/8-16 Center Lock
04041-08 Washer, 3/4-.766 x 1.2 x .06
04041-08S Washer, 3/4-.766 x 1.2 x .035
48100-05 Bushing, 3/4 Sintered
10A 45861
11
12
13
14
15
16
17
18
19
20
21
22
23
24
48114-04 Grease Fitting, Str. 1/4-28
48051
422214
48679
Lock Washer, Wheel Motor
Hex Castle Nut, 3/4-28 UNEF
Spring, Pump Belt Idler
04019-03 Nut, 5/16-18 Serr. Flange
04063-24 Key, 1/4x1/4x2.75" Clutch Mtg.
04063-01 Key, 1/4x1/4x1.25" Pulley Mtg.
04041-07 Flat Washer, 3/8
48473
48586
04012-04 Setscrew, 5/16-18 x 3/8"
04030-04 Lockwasher, 3/8
04063-14 Key, 5.0 x 5.0 x 25mm
04028-01 Nut, Lug
481502
422215
Wheel Assy., (incl. 31,32)
Brake Drum
04008-01 1/2-20 Serrated Bolt
Pulley, Idler Pump Drive
Pulley, Pump Shaft
46928
Hub, Wheel
481470
Brake Band, 7.5"
04063-07 Key, 3/16 X .75 Woodruff
481416
48553
Wheel Motor
Belt, Pump Drive (Sm Frame)
Belt, Pump Drive (Lg Frame)
Electric Clutch
45212
43032
46940
Pivot, Idler Arm
Swivel Joint
Arm, Idler
24A 48587
x
x
x
x
x
x
x
x
25
26
27
461073
x
x
x
x
x
x
04041-28 Flat Washer .469 x 1.75 x .25
04030-05 Lock Washer, 7/16
23
Download from Www.Somanuals.com. All Manuals Search And Download.
HANDLE ASSEMBLY
89
20
REF.
74
75
16
19
19A
81
11
15
68
90 83
25
16A
76
71
A
18
18A
8
17
7
A
6
11
21
24
2
13
31
22
20
9
19
19A
16A
12
5
4
3
23
24
1
10
82
26
15
14
87
60
41
34
27
91
35
29
11
28
3
86
61
37
78
66
30
85
3
88
37
38
36
40
92 80
34
60
32
69
69A
67
93
39
45
79
78
61
40
39A
87
42
40
63
63A
37
38
43
60
65
44
25 43
46
3
94
64
64A
49
60
24
48
47
51
55
59
52
73
56
61
58
72
70
54
56
62
50
57
55
53
11
SWZ99HA
73
24
Download from Www.Somanuals.com. All Manuals Search And Download.
HANDLE ASSEMBLY
Ref. Part
No. No.
Ref. Part
No. No.
Description
14KA 15KH 17KA 20CVE
Description
14KA 15KH 17KA 20CVE
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
04001-69 Hex Head Bolt, 5/16-18 x 1-3/4"
48494-02 Spring, Return
481517-02 Knob, 5/16-18
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
1
1
2
3
4
5
6
7
8
9
10
11
12
13
461128 Upper Handle Wlmt. W/Decals
461129 Upper Handle Wlmt. W/Decals
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
42675
Quadrant, Speed Control
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
43308
45292
Bushing
Handle, Neutral Adj
04062-02 Hairpin, .094 x 1.19
45282
43086
Lever, Speed Adjustment
Bushing, Speed Adjustment Lever
04065-05 Drive Pin, 5/32 x 7/8 Type U
04001-08 HH Bolt,5/16-18 x 3/4"
04030-03 Lock Washer, 5/16
04001-20 Hex Head Bolt, 3/8-16 x 1-1/2"
48493-01 Ball Plunger
04019-03 Nut, 5/16-18 Serr. Flange
48092
Knob, Speed Adjustment
48224
46747
Bearing, Ball Neutral Return
Cam, Neutral (incl. grease ftng.)
04014-01 Capscrew, 1/4-20 x 3/4" FHHS
04021-08 Nut, 1/4-20 Elastic Stop
04021-10 Nut, 5/16-18 Elastic Stop
04010-01 Screw, #10-32 x 1/2" PW HD
481071 Throttle Control
48114-05 Grease Fitting, 1/4-28 UNF
04050-01 Retaining Ring, 5/8 Ext. "E"
04001-09 Hex Head Bolt, 5/16-18 x 1"
45295
Shaft, Pump Control-LH
Shaft, Pump Control-RH
Bellcrank, Pump Control-LH
Bellcrank, Pump Control-RH
13A 48946
Throttle Control
04019-01 Nut, #10-32 Serr. Flange
x
x
x
x
x
x
x
x
x
x
63A 45283
64 45642
64A 45643
65
66
67
68
69
14
15
16
x
x
x
x
x
x
x
x
x
x
x
x
x
x
48312
45572
Bushing
Handle, Oper. Presence-RH
Handle, Oper. Presence-LH (20")
Handle, Oper. Presence-LH (16")
04050-10 Retaining Ring, 1/2 Ext. "E"
04041-07 Flat Washer, 15/16x25/64x12 ga
16A 45571
16A 45573
17
By Ref.
Deck, Engine
481687 Switch,Elec.Clutch Eng. (incl.Nut)
481680 Wire Harness, Manual Start
x
x
x
x
04001-10 Hex Head Bolt, 5/16-18 x 1-1/4"
18
481278
Choke Control
18A 481681 Wire Harness, Electric Start
69A 481072
Choke Control
Spring, Return
Fuse Holder
Swivel Joint, Steering Rod
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
19
19A 48798
20 46942
20A 46941
48609
Key Switch, Manual Srt. (incl. Hdw)
Key Switch, Elec. Start (incl. Hdw.)
Neutral Latch-RH
Neutral Latch-LH
Switch, Neutral Interlock
Grip
x
x
x
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
481057
42413
43306
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
04040-04 Flat Washer (.344 x .688 x .065)
48298 Blade Fuse, 20A
04021-01 Nut, #10-32 Elastic Stop
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
48717
48159
04032-01 Washer, Curved Spring
04040-15 Flat Washer
04031-08 Lock Washer,1/4" Int. Tooth
04001-17 Hex Head Bolt, 5/16-18 x 2"
04001-53 Hex Hd. Bolt, 5/16-18 x 2-1/2"
46744
48492
44050
48951
04017-27 Capscr., 3/8-16 x 1" Ser. Flange
04030-02 Lock Washer, !/4"
04019-04 Nut, 3/8-16 Serr. Flange
44051
45279
04010-03 Screw, #10-32 x 1-1/2" Phillips
43305
43032
44125
Pin, Neutral Lock
Swivel Joint
Rod, Brake Lever
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
04001-21 Hex Hd. Bolt, 3/8-16 x 1 3/4
04015-13 Soc. Hd. Capscrew, #8-32 x 1/2
04021-09 Nut, 3/8-16 Elastic Stop
04041-23 Washer #8-.170 x .375 x .032
04050-01 Retaining Ring, 5/8 Ext, "E"
43212
46954
481476
Lever, Steering Control (incl. 29)
Grip, Steering Control
Rod, Steering Control
Spring, Handle Return
Spacer
Parking Brake Lever with Grip
Switch, Parking Brake
Rod Speed Control
Bellcrank, Speed Control
04020-14 Nut, 3/8-24
481411
481420
48342
48464
Bushing, bearing Retainer
04012-02 Setscrew, 1/4-28 x 1/4"
46335
43166
Bearing, Neutral Lock
Grip, Parking Brake
Ball Joint, RH Thread
Cam, Speed Control (incl. SS)
Jackshaft, Speed Control
Jackshaft, Speed Control
39A 43155
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
04062-01 Hairpin, .094 x 1.62
481622 Bracket, Choke Mtg. (16" Only)
40
41
42
43
44
45
46
47
48
04063-13 Key, 1/8 x 1/2" Woodruff
04021-10 Nut, 3/8-16 Elastic Stop
46336
48100-04 Bushing, 1/2" ID
04017-17 Capscrew, 5/16-18 x 1" Serr. Flg.
04019-03 Nut, 5/16-18 Serrated Flange
42730
43161
48409
Pivot, Pump Ctrl. (incl.Bshg & Zrk)
Bar, Speed Control
Spacer, Speed Ctrl. Bearing
Bearing, Speed Ctrl. Bellcrank
* Common hardware which should be purchased locally. All bolts Grade 5 plated, all other fasteners zinc plated.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
HYDRAULIC ASSEMBLY
1
2
K
B
B
21
E
13
5
4
7
4
4
3
32
30
3
35
8
4
29
6
5
E 22
D
31
5
D
A
22
12
13
20
C
23
35
11
10
10
28
C
18
18A
11
A
H
13
17
15
28
7
4
6
J
24
14
4
29
J
16
8
H
10
19
11
10
19
28
33
12
28
K
10
34
9
11
10
F
G
25
26
G
F
10
10
19
19
21
27
030441798
26
Download from Www.Somanuals.com. All Manuals Search And Download.
HYDRAULIC ASSEMBLY
Ref. Part
No. Number Description
14KA 15KH 17KA
20CVE
1
2
2
3
4
5
6
7
8
48535
46618
46619
48484-01
48353-02
48482
48350-04
48603-06
48551
Cap, Oil Reservoir
Oil Reservoir (small Frame)
Oil Reservior (Large Frame)
Elbow, 90 deg. Female 1/4 NPT to 1/4 JIC Male
Coupling, 7/16-20 SAE Flare Swivel to 1/4" Hose Push On
Hose, 1/4" ID - 12" Long (Order By The Inch)
Elbow, 90 deg. 7/16-20 JIC to 9/16-18 "O" Ring
O-Ring
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
Pump, Hydro-Gear BDP-10L117
x
9
04003-11
481265
48603-02
48350-03
48482
48471-02
48489-02
43096
48936-03
04017-16
04017-22
48603-04
48486-01
04019-03
481562
Bolt, Carriage, 3/8-16 x 1-1/4"
Hose, Pump to Motor
O-Ring
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
10
11
12
13
14
15
16
17
18
18A
19
20
21
22
23
24
25
25
26
27
28
29
30
31
32
33
34
35
Elbow, 90 deg., 7/16-20 JIC x 7/16-20 O-Ring
Hose, 1/4" ID - 10" Long (Order By The Inch)
Oil Filter Base
Elbow, 90 deg. Male 3/4-16 JIC to 1/2" Male NPT
Spacer, Oil Filter Base (20" Frame)
Coupling, 3/4-16 SAE to 1/2" Hose Push On
Capscrew, 5/16-18 x .75" (For 16") Serr. Flange
Capscrew, 5/16-18 x 2.25" (For 20") Serr. Flange
O-Ring
Elbow, 90 deg. Male 1/4 NPT to 1/4 Hose Push On
Nut, 5/16-18 Serr. Flange
Hose, Formed 1/2" ID
Coupling, 1/4 straight Male NPT to 1/4 Hose Push On
Bolt, 5/16-18 x 3/4" Carriage
Engine Deck (16" Wide) W/Decals
Engine Deck (20" Wide) W/Decals
Nut, 3/8-16 Serr Flange
Oil Filter
Elbow, 45 Deg.-3/4-16 JIC Male x Male 3/4-16 O-Ring
O-Ring
Coupling, 3/8 Pipe to 1/2 Push-on
T-Fitting, 3/8 NPT
Plug, 3/8-18 NPTF Magnetic
Screw, 1/4-20 x 2.0" Round Head Phillips
Nut, 1/4-20 Elastic Stop
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
48352-02
04003-12
46946
46947
04019-04
48462-01
48485-01
48603-03
481537-02
48491
48731-01
04010-10
04021-08
48136-05
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
Clamp, .87 max dia.
* Common hardware which should be purchased locally. All bolts Grade 5 plated, all other fasteners zinc plated.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
HYDRAULIC PUMP ASSEMBLY
30
26
25
24
23
27
28
22
1
29
19
20
21
17
16
3
15
18
2
11
14
12
13
5
6
8
7
11
10
9
4
SC165G
28
Download from Www.Somanuals.com. All Manuals Search And Download.
HYDRAULIC PUMP ASSEMBLY
Ref. Part
No. Number
Description
1
2
HG 2513017
HG 2513016
Housing Kit (Incl. Housing, Journal Bearing)
End Cap
3
4
HG 9004800-2506 Straight Headless Pin
HG 9007314-0810 Socket Head Screw
5
6
7
HG 2003067
HG 2513027
HG 50273
End Cap Gasket
Charge Pump Kit (Incl. Charge Cover, Gerotor Assy., O-Ring)
Gerotor Assembly
8
HG 9004101-1340 O-Ring
9
HG 2510064
HG 50095
Charge Relief Valve Kit
Socket Head Screw
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
HG 2510027
HG 2513030
HG 9006110-0120 Backup Ring
Check Valve Kit (Incl. Check Plug, Spring, O-Ring, Orifice Check Valve)
Bypass Valve Kit (Incl. Bypass Valve, O-Ring, Back-up Ring)
HG 70079
Cylinder Block Kit
Block Spring
Block Thrust Washer
Roller Thrust Bearing
Swash Plate
Trunnion Arm
Guide Slot
Cradle Bearing
HG 2003014
HG 2003017
HG 2003044
HG 2003087
HG 2003005
HG 2000015
HG 2003023
HG 9008000-0126 Lip Seal
HG 2003020
HG 2003043
HG 2003016
Pump Shaft
Ball Bearing
Retaining Ring
HG 9008000-0128 Lip Seal
HG 2003052
HG 2003018
HG 2513038
HG 2513018
Retaining Ring
Spacer
Shaft Kit (Incl. Pump Shaft, Ball Bearing, Retaining Ring)
Overhaul Seal Kit (Incl. Gasket, Trunnion Seal, Input Shaft Seal, Charge Pump O-Ring)
* Common hardware which should be purchased locally. All bolts Grade 5 plated, all other fasteners zinc plated.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
BLADE
CLUTCH
ENGINE DECK
WIRE HARNESS -
KOHLER,
NEUTRAL
INTERLOCK
(SINGLE CYLINDER)
& 17 HP Kawasaki
PART NO. 481073
GROUND
BLACK
BLACK
E
F
A
B
C
D
BLUE
WHITE
G
H
WHITE
YELLOW
WIRE HARNESS
ADAPTER - ENGINE
INSTRUMENT
SWZ99SC421G
PANEL HARNESS
TRANSMISSION
ENGINE DECK
WIRE HARNESS -
KOHLER COMMAND
V-TWIN
ENGINE
GROUND
PART NO. 481075
TO ENGINE
BLACK W/RED STRIPE
RED
GREEN
BLACK
E
F
A
B
C
D
BLUE
WHITE
BLACK
G
H
WHITE
YELLOW
ELECTRIC
CLUTCH
TO INSTRUMENT
PANEL CONNECTOR
STARTER
SOLENOID
SC422G
30
Download from Www.Somanuals.com. All Manuals Search And Download.
HANDLE WIRE HARNESS - ELECTRIC START
PART NO. 481681
FUSES
MOWER
ENGAGE
KEY
SWITCH
SWITCH
BRAKE
SWITCH
RED
GREEN
A
B
C
D
E
F
BLACK
BLACK W/RED STRIPE
G
H
BLUE
TO
OPERATOR
PRESENCE
SWITCH
WHITE
TO ENGINE
DECK WIRE
HARNESS
YELLOW
BLACK W/RED STRIPE
RED W/YEL STRIPE
NEG
HOURMETER
POS
HOURMETER
SWZ99-481681
WIRE HARNESS WITH RELAY
PART NO. 481275
To Engine
Ground
RELAY
GREEN
To Starter
BLUE
RED
To Blue Wire
From Engine
SC481275
To Starter
Red Battery
Cable Post
31
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGINE DECK WIRE HARNESS -
KAWASAKI
NEUTRAL
INTERLOCK
PART NO. 481074
ENGINE
REGULATOR
BLACK W/RED STRIPE
BLACK
E
F
A
B
C
D
BLACK
BLUE
WHITE
G
H
WHITE
YELLOW
BLADE
CLUTCH
INSTRUMENT
PANEL HARNESS
SWZ99SC417G
GROUND
HANDLE WIRE HARNESS -
MANUAL START
BRAKE
SWITCH
MOWER
ENGAGE
SWITCH
KEY
SWITCH
PART NO. 481680
WHITE
BLACK W/RED STRIPE
BLACK
A
B
C
E
F
BLACK
BLUE
WHITE
G
BLACK W/RED STRIPE
YELLOW
D
H
TO
TO ENGINE
DECK WIRE
HARNESS
OPERATOR
PRESENCE
SWITCH
NEG
POS
HOURMETER
HOURMETER
SWZ99-481680
32
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT DECALS & INFORMATION
HEAVY DUTY
COMMERCIAL
48072
48072
48314
WARNING
DANGER
ROTATING BLADES AND BELTS
KEEP HANDS, FEET & CLOTHING CLEAR
KEEP ALL GUARDS IN PLACE
SHUT OFF ENGINE & DISENGAGE BLADE
CLUTCH BEFORE SERVICING
SPINNING BLADE
36" - 48316
48" - 48318
52" - 48319
61" - 48320
72" - 48327
KEEP CLEAR
CLEAR AREA OF DEBRIS BEFORE MOWING
USE CAUTION IN DIRECTING DISCHARGE
KEEP BYSTANDERS, CHILDREN & PETS AWAY
READ INSTRUCTION MANUAL BEFORE OPERATING
DO NOT OPERATE WITHOUT DISCHARGE CHUTE, MULCHING
CONTACT CAN INJURE
48071
481040
KIT, OR ENTIRE GRASS CATCHER INSTALLED
48071
481040
PARKING
BRAKE
CHOKE
MANUFACTURED UNDER ONE OR MORE
OF THE FOLLOWING PATENTS:
FAST
OFF
4,487,006
4,885,903
4,920,733
4,967,543
4,991,382
4,998,948
4,118,617
PATENTS PENDING
ON
SLOW
48656
481414
CAUTION
MOWER DECK ON
BEFORE OPERATING
PULL OUT TO ENGAGE
READ OPERATORS
MANUAL AND SAFETY
INSTRUCTIONS
CAUTION
ON
KEEP BYSTANDERS AWAY
48481684
PUSH IN TO DISENGAGE
OFF
48404
48404
481684
WARNING
WARNING
MOUNT RIDING
ATTACHMENT
HERE
FALLING HAZARD
INSTALL BELT COVER BEFORE
OPERATING MACHINE
USE ONLY SCAG APPROVED
RIDING ATTACHMENTS
481109
SEE OPERATOR'S MANUAL
READ OPERATOR'S MANUAL
481039
481039
481109
33
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT DECALS & INFORMATION
PARKING
BRAKE
CHOKE
FAST
OFF
ON
SLOW
481415
PARKING
BRAKE
FAST
OFF
ON
SLOW
481423
PARKING
BRAKE
FAST
OFF
ON
SLOW
481438
34
Download from Www.Somanuals.com. All Manuals Search And Download.
TRACKING ADJUSTMENT
FAST
CONTROL ROD
ADJUSTMENT
REVERSE
SEE
OPERATOR'S
MANUAL
NEUTRAL
OIL
ADJUSTMENT
481425
FORWARD
481425
SEE OPERATOR'S MANUAL
SPEED
CONTROL
481080
SLOW
N
NEUTRAL
481124
481124
48514 - 20"
48555 - 16"
35
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY-COMMERCIAL EQUIPMENT
Any part of the Scag commercial mower manufactured by Scag Power Equipment and found, in the reasonable judg-
ment of Scag, to be defective in materials or workmanship, will be repaired or replaced by an Authorized Scag Service
Dealer without charge for parts and labor. This warranty is limited to the original purchaser and is not transferable.
Proof of purchase will be required by the dealer to substantiate any warranty claims. All warranty work must be
performed by an Authorized Scag Service Dealer.
This warranty is limited to the following specified periods from the date of the original retail purchase for defects in
materials or workmanship:
* Wear items including drive belts, blades, hoses and tires are warranted for 90 days.
* Batteries are covered for 90 days.
* Frame, deck, and structural components including oil reservoir, fittings, and oil cooler
are warranted for 1 year.
* Engines and electric starters are covered by the manufacturer’s warranty period.
* Drive system components are warranted for 1 year by the component manufacturer, in
conjunction with Scag Power Equipment. (Excluding fittings, hoses, cooling system,
oil reservoir, drive belts).
* Electric clutches have a Limited Warranty for 2 years. (Parts and labor 1st year; Parts Only
2nd year)
* Cutter Spindle Assemblies 46631 have a Limited Warranty for three years (Parts and
labor 1st year; Parts only 2nd and 3rd year).
Any Scag product used for rental purposes is covered by a 90 day warranty.
The Scag mower, including any defective part must be returned to an Authorized Scag Service Dealer within the
warranty period. The expense of delivering the mower to the dealer for warranty work and the expense of returning it
to the owner after repair will be paid for by the owner. Scag’s responsibility is limited to making the required repairs
and no claim of breach of warranty shall be cause for cancellation or rescission of the contract of sale of any Scag
mower.
This warranty does not cover any mower that has been subject to misuse, neglect, negligence, or accident, or that has
been operated in any way contrary to the operating instructions as specified in the Operator’s Manual. The warranty
does not apply to any damage to the mower that is the result of improper maintenance, or to any mower or parts that
have not been assembled or installed as specified in the Operator’s Manual and Assembly Manual. The warranty does
not cover any mower that has been altered or modified, changing performance or durability. In addition, the warranty
does not extend to repairs made necessary by normal wear, or by the use of parts or accessories which, in the reasonable
judgment of Scag, are either incompatible with the Scag mower or adversely affect its operation, performance or
durability.
Scag Power Equipment reserves the right to change or improve the design of any mower without assuming any obliga-
tion to modify any mower previously manufactured.
All other implied warranties are limited in duration to the one (1) year warranty period or ninety (90) days for mowers
used for rental purpose. Accordingly, any such implied warranties including merchantability, fitness for a particular
purpose, or otherwise, are disclaimed in their entirety after the expiration of the appropriate one year or ninety day
warranty period. Scag’s obligation under this warranty is strictly and exclusively limited to the repair or replacement
of defective parts and Scag does not assume or authorize anyone to assume for them any other obligation. Some states
do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
Scag assumes no responsibility for incidental, consequential or other damages including, but not limited to, expense for
gasoline, expense of delivering the mower to an Authorized Scag Service Dealer and expense of returning it to the
owner, mechanic’s travel time, telephone or telegram charges, rental of a like product during the time warranty repairs
are being performed, travel, loss or damage to personal property, loss of revenue, loss of use of the mower, loss of time
or inconvenience. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Download from Www.Somanuals.com. All Manuals Search And Download.
© 1999
PART NO. 03056
PRINTED1/99
PRINTED IN USA
SCAG POWER EQUIPMENT
DIVISION OF METALCRAFT OF MAYVILLE, INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
|