MODEL TS
ACCESSORY FOR:
STT - ALL MODELS
STC - MODELS ABOVE SERIAL NUMBER 7630001
THIS MANUAL CONTAINS THE OPERATING
INSTRUCTIONS AND SAFETY INFORMATION
FORYOUR SCAGACCESSORY. READING THIS
MANUAL WILL PROVIDE YOU WITH MAIN-
TENANCE AND ADJUSTMENT PROCEDURES
TO KEEP YOUR ACCESSORY PERFORMING
TO MAXIMUM EFFICIENCY. THE SPECIFIC
MODELS THAT THIS BOOK COVERS ARE CON-
TAINED ON THE INSIDE COVER. BEFORE
OPERATING YOUR MACHINE, PLEASE READ
ALL THE INFORMATION ENCLOSED.
© 2004
SCAG POWER EQUIPMENT
DIVISION OF METALCRAFT OF MAYVILLE, INC
WWW.SCAG.COM
PART NO. 03158
PRINTED 8-2004
PRINTED IN USA
Download from Www.Somanuals.com. All Manuals Search And Download.
2.1SAFETYINFORMATION
1.1INTRODUCTION
-NOTE-
This manual has been prepared to provide the
information you need to correctly assemble, operate,
and maintain this Tiger Striper. Read it carefully and
keep it for future reference.
To avoid personal injury, it is imperative that all
safety instructions be observed.
1. Read this operator's manual and the
operator's manual that is supplied with the
machine this attachment is used on.
The replacement of any part on this product by other
than the manufacturer's authorized replacement part
may adversely affect the performance, durability or
safety of this product.
A replacement manual is available from your
authorized Scag Service Dealer or by contacting:
Scag Power Equipment, Service Department at P.O.
Box 152, Mayville, WI 53050. You may also contact
indicate the complete model number of your Scag
product when ordering a replacement manual.
USE OF OTHER THAN ORIGINAL SCAG
REPLACEMENT PARTS WILL VOID THE
WARRANTY.
If additional information or service is needed that is
not outlined in this manual, please contact your Scag
Power Equipment dealer. Scag dealers are trained in
the latest service methods and carry a full line of Scag
replacement parts.
2. Before removing the Tiger Striper, disengage the
mower, stop the engine and wait for all
movement to stop.
3. ALWAYS turn the engine OFF, remove the key
and wait for all movement to stop before
When ordering parts, always provide the complete
model of this Tiger Striper.
servicing, cleaning or removing the Tiger Striper.
All information provided in this manual is based upon
information available at the time of printing. Scag
Power Equipment reserves the right to make changes
at any time without notice or obligation.
4. Do not modify or alter any component of the
Tiger Striper attachment or mower.
5. Do not allow any passengers to ride on the
mower.
1.2DIRECTIONREFERENCE
The "Right" and "Left", "Front" and "Rear" of the
machine are referenced from the normal operating
position.
2.2 OPERATING INSTRUCTIONS
To operate the Tiger Striper, you will need to lower
the roller to the operating position. The Tiger Striper
can be easily removed or locked in the transport
position whenever the machine is being transported
or when striping is not needed.
1. To unlock the Tiger Striper from the transport
position, lift up slightly on the handle and turn the
lock pin until the small roll pin lines up with the
slot. See Figure 2-1 on page 2.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Repeat on opposite side.
Roll Pin
4. Once the Tiger Striper is locked in the transport
position, remove the quick pins securing the
Tiger Striper to the mounting brackets. See
Figure2-3
Lift Up on
Handle
Push and Turn Pin to line
up Roll Pin with Slot
to Unlock
FIGURE 2-1
2. Repeat this procedure on the opposite side.
The machine is now ready to operate.
Remove Quick Pins
2.3 REMOVING THE TIGER STRIPER
The Tiger Striper can be easily removed whenever
the machine is being transported or when striping is
not needed. To remove the Tiger Striper, follow the
instructionsbelow.
FIGURE 2-3
5. Slide the Tiger Striper off of the mounting
brackets.
1. Prepare the machine so there is easy and safe
access to the work area. Remove the key and
maintain all safety related work procedures.
Always wear eye and hand protection.
6. To install the Tiger Striper, slide the assembly on
to the mounting brackets and reinstall the quick
pins. Once the Tiger Striper has been reinstalled,
follow Section 2.2 Operating Instructions for
proper operation.
2. Lock the Tiger Striper up in the transport
position by lifting upward on the handle, push
and turn the lock pin 90 degrees. The small roll
pin must be out of the slot in the bracket to lock
in the transport position. See Figure 2-2.
3.1 ASSEMBLY INSTRUCTIONS - STT
-NOTE-
Use the illustrated parts list as a part
number reference when following the
assembly instructions.
Roll Pin
1. Remove all packaging materials. Lay out the
mounting hardware and the Tiger Striper
assembly for easy access.
Push and
Turn Pin to
Lock
2. Prepare the machine so there is easy and safe
access to the work area. Remove the key and
maintain all safety related work procedures.
Always wear eye and hand protection.
FIGURE 2-2
2
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Attach the mounting brackets to the cross bar
between the wheel motor brackets using (4) u-
bolts and (8) serrated flange nuts. See Figure
3-1. Do not tighten the hardware.
5. Install the left and right hand Striper Stop
Brackets (p/n 423953 & p/n 423954) to the
frame and secure with (4) 3/8-16 x 1" bolts and
(4) elastic stop nuts. See Figure 3-2.
(4) 3/8-16 Elastic
Stop Nut
-NOTE-
423953 L.H.
Stop Bracket
If the Tiger Striper is installed on an STT with
a serial number below 7219999, part
number 423966 mounting spacer will need to
be installed between the mounting bracket
and cross bar. See Figure 3-1.
(4) 3/8-16 x 1" Bolt
423954 R.H.
Stop Bracket
(4x) U-Bolts
Mounting
Bracket
FIGURE 3-2
6. Install the Tiger Striper roller assembly to the
mounting brackets and secure with the quick
pins.
(8x) Serrated Flange
Nuts
Mounting
Bracket
7. Once the Tiger Striper roller assembly is installed
and secure, tighten the mounting hardware on
both mounting brackets.
STT with a serial number of 7219999 or Below
8. Follow Section 2.2 Operating Instruction for
proper operation.
(4x) U-Bolts
Mounting
Spacer
Mounting
Bracket
3.2 ASSEMBLY INSTRUCTIONS - STC
Mounting
Spacer
-NOTE-
Use the illustrated parts list as a part
number reference when following the
assembly instructions.
Mounting
Bracket
(8x) Serrated Flange
Nuts
1. Remove all packaging materials. Lay out the
mounting hardware and the Tiger Striper
assembly for easy access.
FIGURE 3-1
4. The edge of the mounting bracket should be
under the wheel motor mounting plate for proper
installation. See Figure 3-1.
2. Prepare the machine so there is easy and safe
access to the work area. Remove the key and
maintain all safety related work procedures.
Always wear eye and hand protection.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Attach the mounting brackets to the cross bar
between the wheel motor brackets using (4)
u-bolts and (8) serrated flange nuts. See Figure
3-3. Do not tighten the hardware.
4.1 LAWN STRIPING
HOW DOES LAWN STRIPING WORK?
The “stripe” that you see on the lawn is actually light
reflecting off the blades of grass. The direction in
which the grass is bent determines the “light” or
“dark” stripe. When the blades of grass are bent
away from you, the grass appears lighter in color
because light is reflecting off of the length of the
blade. When the blades of grass are bent towards
you, the stripe appears darker as you are looking at
more of the tips of the blades (a smaller reflective
surface) and the shadows under the blades of grass.
Cutting a lawn in the up/down, north/south, east/
west, opposing directions provides the best stripe
effect.
-Note-
The Tiger Striper cannot be installed on an
STC with a serial number below 7630001.
(4x) U-Bolts
Mounting
Spacer
Mounting
Bracket
You may find that certain grasses have a more
noticeable stripe (stripe easier) than others. Cutting
the grass at a different height can sometimes change
the intensity of the stripe. A slightly higher cut
(example: 3" versus 2.5") can provide more grass to
be bent over, thus producing a more noticeable
stripe. In some types of grass, this may have the
opposite or no effect.
Mounting
Spacer
(8x) Serrated Flange
Nuts
Mounting
Bracket
Grass that tends to be "stiff" and resists bending will
not yield a stripe as well as a softer grass that bends
easily.
FIGURE 3-3
Note that you do not need to cut the grass in order to
stripe it. The roller simply needs to be in the
unlocked/engaged position. You may find that when
creating more advanced, overlapping striping
4. The edge of the mounting bracket should be
under the wheel motor mounting plate for proper
installation. See Figure 3-3.
patterns, you can complete the job faster by applying
the overlaying stripes without the blades engaged.
5. Install the Tiger Striper roller assembly to the
mounting brackets and secure with the quick
pins.
Striping can be used to draw attention to particular
landscape features. It can be used to further
enhance the finished, manicured cut that your Scag
mower delivers.
6. Once the Tiger Striper roller assembly is installed
and secure, tighten the mounting hardware on
both mounting brackets.
7. Follow Section 2.2 Operating Instruction for
proper operation.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
"Checkerboard" pattern:
LAWN STRIPING GUIDELINES
A stripe pattern can add richness and depth to any
lawn. Here are some guidelines to help produce
various patterns and to enhance your striping
techniques.
Begin by mowing the perimeter around the property
(Reference Figure 4-1). Next, mow in opposing
directions (North and South or East and West)
through the remaining portion of the property (as
shown in Figure 4-1). Take care when turning at the
end of each row to prevent turf damage. A simple
"Y" type turn at the end of each row will reduce the
chance of turf damage while setting the mower up
for the next row to be mowed.
Basic stripe pattern:
Begin by mowing the perimeter around the property
(Reference Figure 4-1). Next, mow in opposing
directions through the remaining property (as shown
in Figure 4-1). Take care when turning at the end of
each row to prevent turf damage. A simple "Y"
type turn at the end of each row will reduce the
chance of turf damage while setting the mower up
for the next row to be mowed.
Now, travel in the opposite direction of the original
mowing pattern (if you were mowing North and
South, now mow East and West, etc). Reference
Figure 4-2.
Finish the job by mowing the perimeter again. This
will remove any stripe pattern irregularities left from
turning at the end of each row and delivers a finished
look.
Finish the job by mowing the perimeter again. This
will remove any stripe pattern irregularities left from
turning at the end of each row and delivers a
finishedlook.
FIGURE 4-2
FIGURE 4-1
"Diagonal or Criss-Cross" pattern:
This pattern is achieved using the same techniques as
the "Checkerboard" pattern. Simply apply the stripes in a
diagonal direction. See Figure 4-3.
FIGURE 4-3
5
Download from Www.Somanuals.com. All Manuals Search And Download.
TIGER STRIPER ASSEMBLY - STT
STT with a serial number of 7219999 or Below
4 (4x)
30
5
15
17
1 (4x)
30
2
4 (4x)
3 (4x)
5
6
7
8
1 (4x)
20
9
16
15
10
11
14
12
17
19
8
16
18
27
13
31
26
6
25
21
3 (4x)
6
6
23
7
24
12
22
27
10
27
27
11
23
26
27
28
29
27
9
STT-TS Exploded View
6
Download from Www.Somanuals.com. All Manuals Search And Download.
TIGER STRIPER ASSEMBLY - STT
Ref.
No.
Part
Number
Description
1
2
04021-09
423953
Nut, Elastic Stop 3/8-16
Striper Stop, L.H.
3
4
5
6
7
8
9
04001-19
04100-01
451660
04041-11
04001-22
04019-04
04050-02
461777
Bolt, Hex Head 3/8-16 x 1"
U-Bolt, 5/16-18 x 1"
Mounting Bracket Weldment, LH.
Flatwasher, 3/8-.406 x 1-1/2" 7 Gauge
Bolt, Hex Head 3/8-16 x 2-3/4"
Nut, Serrated Flange 3/8-16
Retaining Ring, .750 External "E"
Pin, Lift Latch
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
04060-01
482896
04001-31
482894
04019-03
04066-02
451661
482895
43648
451669
451670
Pin, Slotted Spring .156 x 3/4"
Spring, Lock Pin
Bolt, Hex Head 3/8-16 x 2-1/2"
Spring, Torsion L.H.
Nut, Serrated Flange 5/16-18
Quick Pin, .188 Dia.
Mounting Bracket Weldment, R.H.
Spring, Torsion R.H.
Hub, Striper
Pivot Weldment, L.H.
Pivot Weldment, R.H.
Hinge Weldment, L.H.
Set Screw, 3/8-16 x 1/2"
Nut, Elastic Stop 3/8-16
Striper Stop, R.H.
Roller Assembly, Striper End (Incl. Item 3)
Roller Assembly (Incl. Item 28)
Bushing, .752 Oilite
Roller Shaft
Spacer, Striper Mounting
Hinge Weldment, R.H.
451667
04012-06
04021-09
423954
461730
461707
48100-24
43653
423966
451668
7
Download from Www.Somanuals.com. All Manuals Search And Download.
TIGER STRIPER ASSEMBLY - STC
4 (4x)
1
17
6
7
8
20
1
9
16
5
15
16
10
11
14
18
12
8
13
27
26
25
6
19
15
7
21
6
6
23
25
24
28
12
10
25
25
11
23
26
3
25
2
25
9
STC-TS Exploded View
8
Download from Www.Somanuals.com. All Manuals Search And Download.
TIGER STRIPER ASSEMBLY - STC
Ref.
No.
Part
Number
Description
1
423966
Spacer, Striper Mounting
2
43653
Roller Shaft
3
4
5
48100-24
04100-01
451660
Bushing, .752 Oilite
U-Bolt, 5/16-18 x 1"
Mounting Bracket Weldment, LH. **L.H. Mounting Bracket is used on the Right Side on STC
6
7
8
9
04041-11
04001-22
04019-04
04050-02
461777
04060-01
482896
04001-31
482894
04019-03
04066-02
451661
482895
43648
451669
451670
451667
04012-06
04021-09
461707
461730
451668
Flatwasher, 3/8-.406 x 1-1/2" 7 Gauge
Bolt, Hex Head 3/8-16 x 2-3/4"
Nut, Serrated Flange 3/8-16
Retaining Ring, .750 External "E"
Pin, Lift Latch
Pin, Slotted Spring .156 x 3/4"
Spring, Lock Pin
Bolt, Hex Head 3/8-16 x 2-1/2"
Spring, Torsion L.H.
Nut, Serrated Flange 5/16-18
Quick Pin, .188 Dia.
Mounting Bracket Weldment, R.H. **R.H. Mounting Bracket is used on the Left Side on STC
Spring, Torsion R.H.
Hub, Striper
Pivot Weldment, L.H.
Pivot Weldment, R.H.
Hinge Weldment, R.H.
Set Screw, 3/8-16 x 1/2"
Nut, Elastic Stop 3/8-16
Roller Assembly (Incl. Item 3)
Roller Assembly, Striper End (Incl. Item 3)
Hinge Weldment, L.H.
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
9
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
10
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY- COMMERCIAL ACCESSORY
AnypartoftheScagcommercialaccessorymanufacturedbyScagandfound,inthereasonablejudgmentofScag,
tobedefectiveinmaterialorworkmanship,willberepairedorreplacedbyanAuthorizedScagServiceDealerwithout
charge for parts and labor.
The Scag accessory, including any defective part, must be returned to an Authorized Scag Service Dealer within
the warranty period. The expense of delivering the accessory to the dealer for warranty work and the expense of
returningitbacktotheownerafterrepairorreplacementwillbepaidforbytheowner. Scag’sresponsibilityinrespect
toclaimsislimitedtomakingtherequiredrepairsorreplacements,andnoclaimofbreachofwarrantyshallbecause
for cancellation or rescission of the contract of sale of any Scag machine. Proof of purchase will be required by the
dealer to substantiate any warranty claim. All warranty work must be performed by an Authorized Scag Service
Dealer.
This warranty is limited to 90 days from the date of original retail purchase for any Scag accessory that is used for
commercial purposes, or any other income-producing purpose including rental use.
This warranty does not cover any accessory that has been subject to misuse, neglect, negligence, or accident, or
thathasbeenoperatedinanywaycontrarytotheoperating instructionsasspecifiedintheOperator'sManual. The
warranty does not apply to any damage to the accessory that is the result of improper maintenance, or to any
accessory or parts that have not been assembled or installed as specified in the Operator's Manual.
The warranty does not cover any accessory that has been altered or modified. In addition, the warranty does not
extend to repairs made necessary by normal wear, or by the use of parts or accessories which, in the reasonable
judgment of Scag, are either incompatible with the Scag mower or adversely affect its operation, performance or
durability. This warranty does not cover engines and electric starters, which are warranted separately by their
manufacturer.
ScagPowerEquipmentreservestherighttochangeorimprovethedesignofanyaccessorywithoutassumingany
obligation to modify any accessory previously manufactured.
All other implied warranties are limited in duration to the 90 day warranty period. Accordingly, any such implied
warranties including merchantability, fitness for a particular purpose, or otherwise, are disclaimed in their entirety
after the expiration of the appropriate ninety day warranty period. Scag’s obligation under this warranty is strictly
andexclusivelylimitedtotherepairorreplacementofdefectivepartsandScagdoesnotassumeorauthorizeanyone
toassumeanyotherobligationforthem. Somestatesdonotallowlimitationsonhowlonganimpliedwarrantylasts,
so the above limitation may not apply to you.
Scagassumesnoresponsibilityforincidental,consequentialorotherdamagesincluding,butnotlimitedto,expense
forgasoline,oil,expenseofdeliveringthemachinetoanAuthorizedScagServiceDealerandexpenseofreturning
it back to the owner, mechanic’s travel time, telephone or telegram charges, rental of a like product during the time
warranty repairs are being performed, travel, loss or damage to personal property, loss of revenue, loss of use of
the mower, loss of time, or inconvenience. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Download from Www.Somanuals.com. All Manuals Search And Download.
© 2004
PART NO. 03158
PRINTED 8-2004
PRINTED IN USA
SCAG POWER EQUIPMENT
DIVISION OF METALCRAFT OF MAYVILLE, INC
WWW.SCAG.COM
Download from Www.Somanuals.com. All Manuals Search And Download.
|