Please Read These Instructions
Before Using Your Mower
Operating Instructions
for model
HP474 & SP474 Lawnmowers
with Mountfield RV150 engine
Product Codes:
299174648/BQ
299274648/BQ
These instructions are an addition to and should be read in
conjunction with the Operator Manual enclosed with this mower
Call our Helpline if you have any problems:-
0845 600 2912
Open from 9:00am to 5:00pm Monday to Saturday
10.00am to 4.00pm on Sunday
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
•
•
•
Disengage the engine brake and drive clutch before starting the engine.
Start the engine in accordance with the instructions and with feet well away from the cutter blade.
Do not tilt the mower when starting the engine.
Do not change the engine settings. If adjustments are necessary, contact your dealer.
The safety deflector flap must be in the down position if the mower is used without the grass collection bag in
place.
•
•
•
Operate the machine at a comfortable walking pace, never run behind the mower.
Avoid operating the machine on wet grass whenever possible.
Take care when working on slopes. Mow across the slope, never up and down, and exercise caution when
changing direction. Do not use the mower on slopes of more than 20 degrees.
Exercise extreme caution when reversing or pulling the mower towards you.
Stop the cutter blade when emptying the grass collector, when crossing surfaces other than grass and when
transporting the mower to and from the work area.
•
•
•
Never pick up or carry the mower when the engine is running.
STORAGE & MAINTENANCE
•
•
To reduce the risk of fire, keep the mower and petrol storage areas free of grass, leaves and grease.
Check the mower and grass collector regularly to ensure the machine is in a safe working condition. Replace any
worn or defective parts. Only use genuine replacement parts.
•
•
Store the mower in a dry, secure place out of the reach of children and well away from any fire hazard.
Allow the engine to cool before storage. If the fuel tank has to be drained, this should be done outdoors.
KNOW YOUR MOWER
Operator Presence
Control (OPC)
Lever - Upper
Clutch Lever -
Lower
Throttle Control
Deflector Flap
Pull Cord
Guide
Oil Filler Cap/Dipstick
(located at rear of engine)
Grass Collector
Engine
Handle Securing
Knob
Spark Plug
Height Adjuster
Fuel Filler Cap
Cutter Deck
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO GET MOWING
Your Mountfield lawnmower does not contain petrol or oil and these must be added before use. Running
the mower with insufficient oil can cause serious damage to the engine and will invalidate your
warranty.
NEVER TIP THE MOWER ONTO ITS SIDE AS THIS WILL FLOOD THE AIR FILTER WITH OIL.
To access the underside of the machine lift the front wheels by lowering the handle to the ground.
Carefully remove the mower from the carton and read these Operating Instructions. An Owner’s Manual
for the engine is also included, please read this before starting the engine.
HANDLEASSEMBLY
•
•
•
Raise the handles to the upright positon. With the fixing bolts in place tighten the hand wheels and check the
pivot bolts are also tight (Figure 1).
Engage the Operator Presence Control (OPC) lever to release the engine brake. Pull the starter cord and fit it into
the cord guide as shown.
Use the cable ties to fit the OPC cable (and clutch cable if fitted) to the handle assembly. Take care that the
cables will not impair removal of the grass collector.
Figure 1
GRASS COLLECTOR
•
Remove the plate and washers from the top of the grass collector and clip the plate in place behind the handle.
•
•
Turn the top upside down and fit the frame to it using screws and the washers which were on the plate.
Fit the cloth base by fastening the plastic bars onto the frame, it may help to use a screwdriver as shown in the
drawing to do this. Then click the edge into the groove in the top starting 5-7mm from an end (Figure2).
To fit the grass collector onto the mower, lift the rear safety deflector flap and hook the collector onto the pegs.
•
Figure 2
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTING YOUR MOWER
Read and understand the Safety Precautions before using your mower.
•
•
•
Put Mountfield 4-stroke, or an SAE 10W-30 oil, in the oil filler (Figure 3). Do not overfill, the oil tank capacity is
0.6 litre. Mountfield oil, part number MX855, is available from any Mountfield stockist or B&Q store.
Fill the fuel tank with UNLEADED petrol. Use only clean, fresh petrol - stale fuel may contain deposits that will
clog the carburettor. Do not overfill, the petrol level should be below the bottom of the fuel tank neck..
Ensure that the spark plug lead is securely connected to the spark plug.
Pull Cord
Handle
Fuel Filler
Cap
Oil Filler Cap/
Air Filter
Dipstick
Exhaust
Spark Plug
Figure 3
Figure 4
•
•
Move the throttle control to the “Choke” positiion (Figure 4).
Pull and hold the Operators Presence Control (OPC) lever against the handle to disengage the engine brake.
THE ENGINE WILL NOT START, OR CONTINUE TO RUN, UNLESS THE OPC LEVER IS HELDAGAINST THE
HANDLE.
•
•
•
Pull the starter cord with a strong smooth pull. Do not remove the pull cord from the guide.
When the engine starts move the throttle control from “Choke” to the “Fast” position.
To engage the drive to the rear wheels on Self Propelled models, pull and hold the clutch lever against the handle.
To stop the drive, release the clutch lever.
NOTE: Using the choke is usually unnecessary when starting a warm engine. However, in cool weather it may still be
necessary to use the choke to start the engine.
STOPPING YOUR MOWER
•
Release the Operators Presence Control (OPC) lever; this will engage the engine brake and operate the ignition
safety cut out device.
ADJUSTING THE HEIGHT OF CUT
The height of cut adjustment not only determines the length of the cut grass, it also controls the airflow which carries
clippings into the collector. If the discharge chute becomes blocked, increase the airflow by raising the height of cut.
To prevent blockages when cutting long, thick grass, set the adjustment to the highest setting and cut the grass; then
cut it again on a lower setting.
Figure 5
To adjust the height of cut:
•
•
•
stop the engine and disconnect the spark plug.
put the mower on a level surface.
adjust the cutting height lever by pulling outwards and moving into the required position (Figure 5).
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE EACH USE
•
Always ensure that the mower is in a safe working condition. Inspect the cutter blade for damage; check safety
devices and guards; check that all nuts, bolts and screws are secure.
•
Check the oil level as follows:
Figure 6
a) Remove the oil filler cap and wipe the dipstick clean (Figure 6).
b) Insert the dipstick into the filler neck and tighten down again.
Remove the dipstick and check the oil level; oil should be at the FULL
mark. The oil tank capacity is about 0.6 litre or 20 fluid oz.
c) If the oil level is low add Mountfield oil part number MX855 or a
SAE 10W-30 oil, to the upper limit on the dipstick. Do not overfill; the
oil level should not be above the FULL mark.
•
Fill the fuel tank with unleaded petrol. Do not overfill; the level should
be below the bottom of the fuel tank neck.
MAINTENANCE
Stop the engine and disconnect the spark plug lead before working on the machine. DO NOT TIP
THE MOWER ONTO ITS SIDE AS THIS WILL FLOOD THE AIR FILTER WITH OIL. To access the
underside of the machine, lift the front wheels by lowering the handle until it rests on the ground.
CUTTER BLADE
Examine the cutter blade regularly for wear or damage.
•
•
Aslightly worn blade can be re-sharpened by your local dealer.
If the blade is damaged it should be replaced. Replacement blade kits are available from your Mountfield stockist.
The part number for the blade kit is MS1196. If in doubt refer to your dealer, or telephone 0845 600 2912.
CLUTCH CABLEADJUSTMENT (Self Propelled model only)
•
•
Make sure that the clutch lever is fully released.
Lengthen the cable adjuster by unscrewing it a couple of turns.
(Figure 7)
Figure 7
•
•
Engage the clutch lever and check that the rear wheels lock when
the mower is pulled backwards.
Start the mower and ensure it does not drive when the lever is disen-
gaged.
Cable
ENGINE
An engine manufacturer’s Owner’s Manual is supplied with your mower.
Please read this, it provides detailed information on engine operation
and maintenance. Repair work other than routine maintenance, should
be carried out by an authorised dealer.
Adjuster
STORAGE
Alittle time spent on your mower after use will ensure many years of reliable mowing. To access the underside of the
cutter deck, ensure the spark plug lead is disconnected, then lift the front wheels by lowering the handle until it rests
on the ground. Do not tip the mower onto its side, as this will flood the air filter with oil.
AFTER EACH USE
•
•
•
•
•
Remove any grass pulp from the underside of the cutter deck using a non-metallic instrument such as a piece of
wood. Take care not to damage the paintwork.
Examine the cutter blade for any damage. A damaged blade may upset the balance of your mower and cause
excessive vibration, if in doubt refer to your dealer.
Inspect the grass collector and clean it if necessary. If the mesh becomes clogged airflow will be reduced and
impair grass collection.
The handle can be folded down to reduce the amount of storage space required. Take care not to trap any of the
operating cables when folding or unfolding the handle.
Store the mower in a clean, dry area well away from any naked flames, sparks or heat source.
LONG TERM - If you are not using your mower for more than 28 days.
•
•
•
Give the machine a thorough clean, paying particular attention to the underside.
Lubricate all moving parts.
At the end of the season, empty the fuel tank either by running the mower out of fuel or tip the machine backwards
and onto the back right wheel to drain the fuel into a suitable container. Drain the carburettor by loosening the
drain screw, retighten the drain screw.
Download from Www.Somanuals.com. All Manuals Search And Download.
FAULT FINDING
PROBLEM
SOLUTION
Check there is ample clean, fresh fuel in the tank.
Engine will not start
Check the cutter blade is not fouling the ground preventing free rotation.
Check the Operators Presence Control (OPC) lever is fully released.
Remove spark plug lead to stop engine using insulated gloves and refer to dealer.
Stop the engine and disconnect the spark plug lead using heat resistant gloves.
Check blade attachment bolt is tight.
Engine will not stop
Failure to cut grass properly
Check condition of blade. If seriously worn or damaged replace with a new one.
Stop the engine and disconnect the spark plug lead using heat resistant gloves.
Check and make sure there is no build up of grass inside the casing.
Check grass catcher is allowing air to flow through the fabric; if it is clogged it should be washed
carefully.
Failure to collect grass properly
If the grass catcher is not clogged raise the height of cut to increase airflow.
Check to ensure the engine is running at the correct speed, (approximately 3000rpm).
If conditions are too severe to use the grass catcher, remove it and work with the deflector in position.
This will certainly indicate that the blade has become badly damaged. Stop the engine, disconnect the
spark plug lead and examine the blade assembly. Refer to your local dealer.
Machine vibrates excessively
CERTIFICATE OF CONFORMITY
EC DECLARATION OF CONFORMITY
The company ................................................... GGP ITALY SPA - Via del Lavoro, 6
31033 Castelfranco V.to (TV) ITALY
HP474 type ESL 464
SP474 type ESL 464 TR
Certify that the lawnmower, walk behind with
combustion engine ...........................................
45 cm
SUMEC • M 150
Widht of cut .....................................................
Engine ..............................................................
Tested by ......................................................... SNCH, 11 route de Luxembourg
L-5230 SANDWEILER
98/37/EEC
89/336/EEC ~ 2004/108/EC - 2000/14/EC
Conforms to the specifications of directives .....
ANNEX VI
95 dB(A)
Conformity assessment procedure followed ......
Measured sound power level ............................
Guaranteed sound power level .........................
Reference to harmonised standards..................
96 dB(A)
EN 836 - EN 292-2- EN 1033 - EN ISO 3767
EN ISO 14982
Sound pressure level at the ear measured in compli-
ance with 81/1051/EEC ..............................................
Viration level at the handle (EN 1033) .......................
85 dB(A)
6 m/s2
Castelfranco Veneto (TV) - ITALY
01-10-2008
S. Ferrari (General Manager)
Download from Www.Somanuals.com. All Manuals Search And Download.
Guarantee
GGP UK Limited undertakes to provide a full guarantee against defective materials or workmanship
for two years from the date of purchase subject to the mower receiving an annual service.
If the machine is used for commercial purposes; i.e. for hire; or by contractors, caravan sites or
similar users, this guarantee period shall be 90 days.
If any part or parts are found to be defective within the guarantee period, GGP UK Limited, via their
authorised dealer, will effect the repair or replacement at no charge to the owner providing that the
fault is reported direct to the dealer. All repairs must be carried out by an authorised Mountfield
dealer. Delivery and collection of the machine is the owner’s responsibility and not covered
under the terms of this guarantee.
This guarantee is not transferable. Proof of purchase will be required in the event of a claim.
This guarantee does not apply to the routine replacement of parts that are subject to normal wear and
tear – or to normal service and maintenance parts. This guarantee does not cover faults caused by
neglect or misuse.
The engine manufacturer guarantees the engine fitted to this machine.
This guarantee is in addition to, and does not detract from, the contractual rights of the owner under
statute or common law.
On delivery of your new Mountfield mower, we suggest
that you complete the box to the right.
The information for your machine is on the serial
number label, which is fixed on the cutter deck at the
base of the handles. You will be asked for these details
if you have any problems or require spare parts.
Please keep your receipt, proof of purchase will be
required in the event of a claim.
Service Record
1st Service
2nd Service
Date of Service:
Dateof Service:
Next ServiceDue:
Dealer’sSignature:
Next ServiceDue:
Dealer’sSignature:
Dealer’sStamp:
Dealer’sStamp:
GGP UK LIMITED
Unit 8, Bluewater Estate, Bell Close, Plympton, Plymouth, Devon, PL7 4JH, England.
Part Number 171503943/0
Download from Www.Somanuals.com. All Manuals Search And Download.
|