McCulloch Lawn Mower MC17542ST User Guide
MODEL NO. MC17542ST (MC17542STA)  
17.5 HP 42 Inch  
Lawn Tractor  
For Parts and Service, contact our authorized distributor: call 1-800-849-1297  
For Technical Assistance: call 1-800-829-5886  
193190 Rev. 1 09.21.04 MH/TR  
PRINTED IN U.S.A.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY RULES  
Safe Operation Practices for Ride-On Mowers  
GENERAL SERVICE  
III. CHILDREN  
•
Never operate machine in a closed are.  
Keep all nuts and bolts tight to be sure the equipment  
is in safe working condition.  
Never tamper with safety devices. Check their proper  
operation regularly.  
Keep machine free of grass, leaves, or other debris  
build-up. Clean oil or fuel spillage and remove any fuel-  
soaked debris. Allow machine to cool before storing.  
If you strike a foreign object, stop and inspect the  
machine. Repair, if necessary, before restarting.  
Nevermakeanyadjustmentsorrepairswiththeengine  
running.  
Check grass catcher components and the discharge  
guard frequently and replace with manufacturer's rec-  
ommended parts, when necessary.  
Tragic accidents can occur if the operator is not alert to  
the presence of children. Children are often attracted to  
the machine and the mowing activity. Never assume that  
children will remain where you last saw them.  
•
•
•
•
•
•
•
Keepchildrenoutofthemowingareaandinthewatchful  
care of a responsible adult other than the operator.  
Be alert and turn machine off if a child enters the  
area.  
Before and while backing, look behind and down for  
small children.  
Nevercarrychildren,evenwiththebladesshutoff. They  
may fall off and be seriously injured or interfere with  
safemachineoperation.Childrenwhohavebeengiven  
rides in the past may suddenly appear in the mowing  
area for another ride and be run over or backed over  
by the machine.  
Never allow children to operate the machine.  
Useextracarewhenapproachingblindcorners,shrubs,  
trees, or other objects that may block your view of a  
child.  
•
•
•
•
•
•
Mower blades are sharp. Wrap the blade or wear  
gloves, and use extra caution when servicing them.  
Check brake operation frequently. Adjust and service  
as required.  
Maintain or replace safety and instruction labels, as  
necessary.  
•
•
IV.TOWING  
•
Tow only with a machine that has a hitch designed for  
towing. Do not attach towed equipment except at the  
hitch point.  
•
•
•
•
Follow the manufacturer's recommendation for weight  
limits for towed equipment and towing on slopes.  
Never allow children or others in or on towed equip-  
ment.  
On slopes, the weight of the towed equipment may  
cause loss of traction and loss of control.  
Travel slowly and allow extra distance to stop.  
•
Be sure the area is clear of bystanders before operat-  
ing. Stop machine if anyone enters the area.  
Never carry passengers.  
Do not mow in reverse unless absolutely necessary.  
Always look down and behind before and while back-  
ing.  
•
•
V. SERVICE  
SAFE HANDLING OF GASOLINE  
•
Nevercarrychildren,evenwiththebladesshutoff. They  
may fall off and be seriously injured or interfere with  
safemachineoperation.Childrenwhohavebeengiven  
rides in the past may suddenly appear in the mowing  
area for another ride and be run over or backed over  
by the machine.  
Keepchildrenoutofthemowingareaandinthewatchful  
care of a responsible adult other than the operator.  
Be alert and turn machine off if a child enters the  
area.  
Before and while backing, look behind and down for  
small children.  
Mow up and down slopes (15° Max), not across.  
Choose a low ground speed so that you will not have  
to stop or shift while on the slope.  
Avoid starting, stopping, or turning on a slope. If the  
tires lose traction, disengage the blades and proceed  
slowly straight down the slope.  
To avoid personal injury or property damage, use extreme  
care in handling gasoline.Gasoline is extremely flammable  
and the vapors are explosive.  
•
Extinguish all cigarettes, cigars, pipes, and other  
sources of ignition.  
•
•
•
•
•
Use only approved gasoline container.  
Never remove gas cap or add fuel with the engine run-  
ning. Allow engine to cool before refueling.  
Never fuel the machine indoors.  
Never store the machine or fuel container where there  
is an open flame, spark, or pilot light such as on a water  
heater or other appliances.  
•
•
•
•
•
•
Never fill containers inside a vehicle or on a truck or  
trailer bed with plastic liner. Always place containers  
on the ground away from your vehicle when filling.  
Removegas-poweredequipmentfromthetruckortrailer  
and refuel it on the ground. If this is not possible, then  
refuel such equipment with a portable container, rather  
than from a gasoline dispenser nozzle.  
Keep the nozzle in contact with the rim of the fuel tank  
orcontaineropeningatalltimesuntilfuelingiscomplete.  
Do not use a nozzle lock-open device.  
•
•
•
If machine stops while going uphill, disengage blades,  
shift into reverse and back down slowly.  
Do not turn on slopes unless necessary, and then, turn  
slowly and gradually downhill, if possible.  
•
•
•
If fuel is spilled on clothing, change clothing immedi-  
ately.  
Never overfill fuel tank. Replace gas cap and tighten  
securely.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONGRATULATIONS on your purchase of a new tractor.  
Ithasbeendesigned,engineeredandmanufacturedtogive  
you the best possible dependability and performance.  
PRODUCT SPECIFICATIONS  
GASOLINE CAPACITY  
AND TYPE:  
2.0 GALLONS  
Shouldyouexperienceanyproblemyoucannoteasilyrem-  
edy,pleasecontactyournearestauthorizedservicecenter/  
department. We have competent, well-trained technicians  
and the proper tools to service or repair this tractor.  
UNLEADED REGULAR  
SAE 30 (above 32°F)  
SAE 5W-30 (below 32°F)  
OIL TYPE (API-SG-SL):  
OIL CAPACITY:  
W/FILTER 3.5 PINTS  
W/O FILTER 3.0 PINTS  
Please read and retain this manual. The instructions will  
enable you to assemble and maintain your tractor properly.  
Always observe the “SAFETY RULES”.  
SPARK PLUG:  
(GAP: .030")  
CHAMPION RC12YC  
CUSTOMER RESPONSIBILITIES  
GROUND SPEED (MPH): FORWARD:  
•
•
Read and observe the safety rules.  
Follow a regular schedule in maintaining, caring for  
and using your tractor.  
1st 1.2  
2nd 1.5  
3rd 2.4  
4th 3.5  
5th 4.8  
6th 5.3  
•
Follow the instructions under“Maintenance”and“Stor-  
age” sections of this owner’s manual.  
WARNING: This tractor is equipped with an internal com-  
bustion engine and should not be used on or near any  
unimprovedforest-covered,brush-coveredorgrass-covered  
land unless the engine’s exhaust system is equipped with  
a spark arrester meeting applicable local or state laws (if  
any). If a spark arrester is used, it should be maintained  
in effective working order by the operator.  
REVERSE: 1.5  
FRONT: 14 PSI  
REAR: 10 PSI  
TIRE PRESSURE:  
CHARGING SYSTEM:  
BATTERY:  
3 AMPS BATTERY  
5 AMPS HEADLIGHTS  
A spark arrester for the muffler is available through your  
nearestauthorizedservicecenter/department(SeeREPAIR  
PARTS section of this manual).  
AMP/HR:  
28  
MIN. CCA:  
230  
CASE SIZE: U1R  
27-35 FT. LBS.  
BLADE BOLT TORQUE:  
TABLE OF CONTENTS  
SAFETY RULES .........................................................2-3  
PRODUCT SPECIFICATIONS....................................... 4  
CUSTOMER RESPONSIBILITIES................................. 4  
ASSEMBLY.................................................................6-8  
OPERATION .............................................................9-14  
MAINTENANCE SCHEDULE ...................................... 15  
MAINTENANCE .....................................................15-18  
SERVICE AND ADJUSTMENTS ............................19-23  
STORAGE.................................................................... 24  
TROUBLESHOOTING ............................................25-26  
REPAIR PARTS ......................................................28-41  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTENTS OF HARDWARE PACK  
Steering Wheel  
Seat  
Steering  
Boot  
(1) Washer  
17/32 x 1-3/16 x 12 Gauge  
Steering  
Wheel  
Insert  
Steering  
Extension  
Shaft  
(1) Knob  
Steering  
Wheel  
Adapter  
Key  
(1) Large Flat  
Washer  
(1) Locknut 1/2-20  
(2) Keys  
(1) Oil Drain Tube  
Slope Sheet  
(1) Locknut 1/4-28  
(1) Hex Bolt 1/4-28 x 1-1/4  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes.  
To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use  
the correct tools as necessary to insure proper tightness.  
INSERT  
TOOLS REQUIRED FOR ASSEMBLY  
A socket wrench set will make assembly easier. Standard  
1/2 HEX NUT  
wrench sizes are listed.  
LARGE FLAT  
WASHER  
(2) 7/16" wrenches  
(2) 3/4" wrench  
Pliers  
Utility knife  
Tire pressure gauge  
Whenrightorlefthandismentionedinthismanual,itmeans  
when you are in the operating position (seated behind the  
steering wheel).  
STEERING  
WHEEL  
TO REMOVE TRACTOR FROM  
CARTON  
UNPACK CARTON  
STEERING  
BOOT  
•
•
•
Remove all accessible loose parts and parts cartons  
from carton.  
Cut along dotted lines on all four panels of carton.  
Remove end panels and lay side panels flat.  
Check for any additional loose parts or cartons and  
remove.  
TABS  
ADAPTER  
EXTENSION SHAFT  
1/4 HEX BOLT  
BEFORE REMOVING TRACTOR FROM  
SKID  
1/4 LOCKNUT  
ATTACH STEERING WHEEL (See Fig. 1)  
ASSEMBLE EXTENSION SHAFT AND BOOT  
LOWER  
STEERING  
SHAFT  
•
Slide extension shaft onto lower steering shaft. Align  
mountingholesinextensionandlowershaftsandinstall  
1/4 hex bolt and locknut. Tighten securely.  
TAB  
SLOTS  
IMPORTANT: TIGHTEN BOLT AND NUT SECURELY TO  
10-12 FT. LBS TORQUE.  
•
Place tabs of steering boot over tab slots in dash and  
push down to secure.  
FIG. 1  
INSTALL STEERING WHEEL  
•
•
•
•
•
•
Position front wheels of the tractor so they are pointing  
INSTALL SEAT (See Fig. 2)  
Adjust seat before tightening adjustment knob.  
straight forward.  
Remove steering wheel adapter from steering wheel  
and slide adapter onto steering shaft extension.  
Position steering wheel so cross bars are horizontal  
(left to right) and slide inside boot and onto adapter.  
Assemble large flat washer, 1/2 hex nut and tighten  
securely.  
Snap steering wheel insert into center of steering  
wheel.  
Remove protective materials from tractor hood and  
grill.  
•
Remove adjustment knob and flat washer securing  
seat to cardboard packing and set aside for assembly  
of seat to tractor.  
•
•
•
•
Pivotseatupwardandremovefromthecardboardpack-  
ing. Remove the cardboard packing and discard.  
Place seat on seat pan so head of shoulder bolts are  
positioned over the large slotted holes in pan.  
Push down on seat to engage shoulder bolts in slots  
and pull seat towards rear of tractor.  
Pivot seat and pan forward and assemble adjustment  
knob and flat washer loosely. Do not tighten.  
IMPORTANT: CHECKFORANDREMOVEANYSTAPLES  
INSKIDTHATMAYPUNCTURETIRESWHERETRACTOR  
IS TO ROLL OFF SKID.  
•
•
Lower seat into operating position and sit in seat.  
Slide seat until a comfortable position is reached  
which allows you to press clutch/brake pedal all the  
way down.  
•
•
Get off seat without moving its adjusted position.  
Raise seat and tighten adjustment knob securely.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
SEAT  
SEAT PAN  
LABEL  
SEAT PAN  
SHOULDER  
BOLTS  
02617  
02602  
FIG. 4  
FLAT WASHER  
NOTE: You may now roll or drive your tractor off the skid.  
Follow the appropriate instruction below to remove the  
tractor from the skid.  
ADJUSTMENT  
KNOB  
02615  
TO ROLL TRACTOR OFF SKID (See Op-  
eration section for location and function of  
controls)  
FIG. 2  
•
Press lift lever plunger and raise attachment lift lever  
to its highest position.  
CONNECT BATTERY (See Figs. 3 and 4)  
•
Release parking brake by depressing clutch/brake  
CAUTION: Do not short battery termi-  
nals by allowing a wrench or any other  
object to contact both terminals at the  
same time. Before connecting battery,  
remove metal bracelets, wristwatch  
bands, rings, etc.  
pedal.  
•
•
•
Place gearshift lever in neutral (N) position.  
Roll tractor forward off skid.  
Remove banding holding deflector shield up against  
tractor.  
TO DRIVE TRACTOR OFF SKID (See Op-  
eration section for location and function of  
controls)  
Positive terminal must be connected  
firsttopreventsparkingfromaccidental  
grounding.  
WARNING: Before starting, read, understand and follow  
all instructions in the Operation section of this manual. Be  
sure tractor is in a well-ventilated area. Be sure the area in  
front of tractor is clear of other people and objects.  
•
•
•
Lift seat pan to raised position.  
Remove terminal protective caps and discard.  
If this battery is put into service after month and year  
indicated on label (label located between terminals)  
charge battery for minimum of one hour at 6-10 amps.  
(See "BATTERY" in the Maintenance section of this  
manual for charging instructions).  
First connect RED battery cable to positive (+) terminal  
with hex bolt and keps nut as shown. Tighten securely.  
Slide terminal cover over terminal.  
•
Be sure all the above assembly steps have been com-  
pleted.  
•
•
Check engine oil level and fill fuel tank with gasoline.  
Sit on seat in operating position, depress clutch/brake  
pedal and set the parking brake.  
•
•
•
•
Place gear shift lever in neutral (N) position.  
Press lift lever plunger and raise attachment lift lever  
to its highest position.  
Connect BLACK grounding cable to negative (-) ter-  
minal with remaining hex bolt and keps nut. Tighten  
securely.  
•
•
•
•
•
Starttheengine.Afterenginehasstarted,movethrottle  
control to idle position.  
Depress clutch/brake pedal into full “BRAKE” position  
and hold. Move gearshift lever to 1st gear.  
Slowly release clutch/brake pedal and slowly drive  
tractor off skid.  
Applybraketostoptractor, setparkingbrakeandplace  
gearshift lever in neutral position.  
DISCARD TERMINAL  
PROTECTIVE CAPS  
KEPS  
NUT  
HEX BOLT  
TERMINAL  
COVER  
Turn ignition key to “OFF” position.  
Continue with the instructions that follow.  
02604  
POSITIVE (RED) CABLE  
NEGATIVE (BLACK) CABLE  
FIG. 3  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
CHECK TIRE PRESSURE  
The tires on your tractor were overinflated at the factory  
for shipping purposes. Correct tire pressure is important  
for best cutting performance.  
INSTALL MULCHER PLATE (See Fig. 5)  
(If previously removed)  
•
•
Raise and hold deflector shield in upright position.  
Place front of mulcher plate over front of mower deck  
opening and slide into place, as shown.  
•
Reduce tire pressure to PSI shown in “PRODUCT  
SPECIFICATIONS” section of this manual.  
•
•
Hook front latch into hole on front of mower deck.  
Hook rear latch into hole on back of mower deck.  
CHECK DECK LEVELNESS  
For best cutting results, mower housing should be properly  
leveled. See“TOLEVELMOWERHOUSING”intheService  
and Adjustments section of this manual.  
CAUTION:Donotremovedeflectorshield  
from mower.  
TO  
CONVERT TO  
BAGGING  
OR  
CHECK FOR PROPER POSITION OF ALL  
BELTS  
See the figures that are shown for replacing motion and  
mower blade drive belts in the Service and Adjustments  
section of this manual. Verify that the belts are routed  
correctly.  
DISCHARGING  
Simply remove mulcher plate and store in a safe place.  
Your mower is now ready for discharging or installation of  
optional grass catcher accessory.  
NOTE: It is not necessary to change blades. The mulcher  
blades are designed for discharging and bagging also.  
CHECK BRAKE SYSTEM  
Afteryoulearnhowtooperateyourtractor,checktoseethat  
the brake is properly adjusted. See “TO ADJUST BRAKE”  
in the Service and Adjustments section of this manual.  
DEFLECTOR  
SHIELD  
MULCHER  
PLATE  
✓CHECKLIST  
BEFOREYOUOPERATEANDENJOYYOURNEW TRAC-  
TOR, WE WISH TO ASSURE THAT YOU RECEIVE THE  
BESTPERFORMANCEANDSATISFACTIONFROMTHIS  
QUALITY PRODUCT.  
LATCH  
HOOKS  
PLEASE REVIEW THE FOLLOWING CHECKLIST:  
✓
✓
✓
All assembly instructions have been completed.  
No remaining loose parts in carton.  
Battery is properly prepared and charged. (Minimum  
1 hour at 6 amps).  
FIG. 5  
✓
✓
Seat is adjusted comfortably and tightened securely.  
All tires are properly inflated. (For shipping purposes,  
the tires were overinflated at the factory).  
✓
Be sure mower deck is properly leveled side-to-side/  
front-to-rear for best cutting results. (Tires must be  
properly inflated for leveling).  
✓
✓
Check mower and drive belts. Be sure they are routed  
properly around pulleys and inside all belt keepers.  
Check wiring. See that all connections are still secure  
and wires are properly clamped.  
WHILE LEARNING HOW TO USEYOUR TRACTOR, PAY  
EXTRA ATTENTION TO THE FOLLOWING IMPORTANT  
ITEMS:  
✓
Engine oil is at proper level.  
✓
Fuel tank is filled with fresh, clean, regular unleaded  
gasoline.  
✓
✓
Become familiar with all controls - their location and  
function. Operate them before you start the engine.  
Be sure brake system is in safe operating condition.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their mean-  
ing.  
IGNITION  
FAST  
SLOW  
REVERSE  
HIGH  
LOW  
NEUTRAL  
CHOKE  
P
LIGHTS ON  
ENGINE START  
ENGINE ON  
PARKING BRAKE  
PARKING BRAKE PARKING BRAKE  
ENGINE OFF  
LOCKED  
UNLOCKED  
OIL PRESSURE  
BATTERY  
REVERSE  
FUEL  
FORWARD  
OVER TEMP  
LIGHT  
MOWER HEIGHT  
MOWER LIFT  
15  
15  
ATTACHMENT  
CLUTCH ENGAGED  
ATTACHMENT  
CLUTCH DISENGAGED  
SLOPE HAZARDS  
KEEP AREA CLEAR  
(SEE SAFETY RULES SECTION)  
DANGER, KEEP HANDS  
AND FEET AWAY  
DANGER indicates a hazard which, if not avoided,  
will result in death or serious injury.  
WARNING indicates a hazard which, if not avoided,  
could result in death or serious injury.  
FREE WHEEL  
(Automatic Models only)  
CAUTION indicates a hazard which, if not avoided,  
might result in minor or moderate injury.  
CAUTION when used without the alert symbol,  
indicates a situation that could result in damage  
to the tractor and/or engine.  
Failure to follow instructions  
could result in serious injury or  
death. The safety alert symbol  
is used to identify safety inform-  
ation about hazards which can  
result in death, serious injury  
and/or property damage.  
HOT SURFACES indicates a hazard which,  
if not avoided, could result in death, serious injury  
and/or property damage.  
FIRE indicates a hazard which, if not avoided,  
could result in death, serious injury and/or  
property damage.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
KNOWYOUR TRACTOR  
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATINGYOUR TRACTOR  
Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments.  
Save this manual for future reference.  
IGNITION  
SWITCH  
LIGHT SWITCH  
POSITION  
ATTACHMENT  
CLUTCH LEVER  
AMMETER  
LIFT LEVER  
PLUNGER  
THROTTLE/  
CHOKE  
CONTROL  
ATTACHMENT  
LIFT LEVER  
HEIGHT  
ADJUSTMENT  
INDICATOR  
CLUTCH/  
BRAKE  
PEDAL  
PARKING  
BRAKE  
GEAR SHIFT  
LEVER  
FIG. 6  
Our tractors conform to the safety standards of the American National Standards Institute.  
AMMETER - Indicates charging (+) or discharging (-) of  
battery.  
IGNITION SWITCH - Used for starting and stopping the  
engine.  
LIFT LEVER PLUNGER - Used to release attachment lift  
lever when changing its position.  
LIGHT SWITCH POSITION - Turns the headlights on and  
off.  
THROTTLE/CHOKE CONTROL - Used for starting and  
controlling engine speed.  
ATTACHMENT CLUTCH LEVER - Used to engage the  
mower blades, or other attachments mounted to your  
tractor.  
ATTACHMENT LIFT LEVER - Used to raise, lower, and  
adjust the mower deck or other attachments mounted to  
your tractor.  
PARKING BRAKE - Locks clutch/brake pedal into the  
brake position.  
CLUTCH/BRAKEPEDAL-Usedfordeclutchingandbrak-  
ing the tractor and starting the engine.  
GEARSHIFT LEVER - Selects the speed and direction  
of the tractor.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
The operation of any tractor can result in foreign objects thrown into the eyes, which can result  
in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or  
performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles  
or standard safety glasses.  
NOTE: Under certain conditions when tractor is standing  
HOW TO USEYOUR TRACTOR  
idlewiththeenginerunning, hotengineexhaustgasesmay  
cause “browning” of grass. To eliminate this possibility, al-  
ways stop engine when stopping tractor on grass areas.  
TO SET PARKING BRAKE (See Fig. 7)  
Your tractor is equipped with an operator presence sens-  
ing switch. When engine is running, any attempt by the  
operator to leave the seat without first setting the parking  
brake will shut off the engine.  
CAUTION: Always stop tractor com-  
pletely,asdescribedabove,beforeleav-  
ing the operator's position; to empty  
grass catcher, etc.  
•
Depress clutch/brake pedal into full “BRAKE” position  
and hold.  
•
Place parking brake lever in“ENGAGED”position and  
releasepressurefromclutch/brakepedal. Pedalshould  
remain in “BRAKE” position. Make sure parking brake  
will hold tractor secure.  
TO USE THROTTLE CONTROL (See Fig. 7)  
Always operate engine at full throttle.  
•
•
Operating engine at less than full throttle reduces the  
battery charging rate.  
Full throttle offers the best bagging and mower perfor-  
mance.  
ATTACHMENT CLUTCH  
LEVER "ENGAGED"  
POSITION  
TO MOVE FORWARD AND BACKWARD  
(See Fig. 7)  
The direction and speed of movement is controlled by the  
gearshift lever.  
IGNITION KEY  
THROTTLE/  
CHOKE  
"DISENGAGED"  
POSITION  
CONTROL  
LEVER  
•
Start tractor with clutch/brake pedal depressed and  
gearshift lever in neutral (N) position.  
Move gearshift lever to desired position.  
Slowly release clutch/brake pedal to start move-  
ment.  
PARKING BRAKE  
"ENGAGED"  
POSITION  
"BRAKE"  
POSITION  
•
•
IMPORTANT: BRING TRACTOR TO A COMPLETE STOP  
BEFORE SHIFTING OR CHANGING GEARS. FAILURE  
TO DO SO WILL SHORTEN THE USEFUL LIFE OF YOUR  
TRANSAXLE.  
GEAR SHIFT  
LEVER  
CLUTCH/BRAKE  
PEDAL "DRIVE"  
POSITION  
PARKING BRAKE  
"DISENGAGED"  
POSITION  
TO ADJUST MOWER CUTTING HEIGHT  
(See Fig. 7)  
FIG. 7  
The position of the attachment lift lever determines the  
STOPPING (See Fig. 7)  
cutting height.  
MOWER BLADES -  
•
•
Grasp lift lever.  
Press plunger with thumb and move lever to desired  
position.  
•
To stop mower blades,move attachment clutch lever  
to “DISENGAGED” position.  
GROUND DRIVE -  
The cutting height range is approximately 1-1/2 to 4".  
The heights are measured from the ground to the blade tip  
withtheenginenotrunning. Theseheightsareapproximate  
and may vary depending upon soil conditions, height of  
grass and types of grass being mowed.  
•
To stop ground drive, depress clutch/brake pedal into  
full “BRAKE” position.  
Move gearshift lever to neutral (N) position.  
•
ENGINE -  
Move throttle control between half and full speed (fast)  
position.  
•
•
The average lawn should be cut to approximately 2-1/2  
inches during the cool season and to over 3 inches  
during hot months. For healthier and better looking  
lawns, mow often and after moderate growth.  
NOTE: Failure to move throttle control between half and  
fullspeed(fast)position,beforestoppingmaycauseengine  
to “backfi r e ” .  
•
For best cutting performance, grass over 6 inches  
in height should be mowed twice. Make the first cut  
relatively high; the second to desired height.  
•
Turn ignition key to “STOP” position and remove key.  
Always remove key when leaving tractor to prevent  
unauthorized use.  
•
Never use choke to stop engine.  
IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY  
POSITION OTHER THAN "STOP" WILL CAUSE THE BATTERY  
TO BE DISCHARGED, (DEAD).  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
TO ADJUST GAUGE WHEELS (See Fig. 8)  
"ENGAGED" POSITION  
Gaugewheels areproperlyadjustedwhentheyareslightly  
off the ground when mower is at the desired cutting height  
in operating position. Gauge wheels then keep the deck  
in proper position to help prevent scalping in most terrain  
conditions.  
ATTACHMENT  
LIFT LEVER  
HIGH POSITION  
LOW  
POSITION  
NOTE:Adjust gauge wheels with tractor on a flat level  
surface.  
•
Adjust mower to desired cutting height (See “TO AD-  
JUST MOWER CUTTING HEIGHT” in the Operation  
section of this manual).  
With mower in desired height of cut position, gauge  
wheels should be assembled so they are slightly off  
the ground. Install gauge wheel in appropriate hole  
with shoulder bolt, 3/8 washer, and 3/8-16 locknut and  
tighten securely.  
ATTACHMENT  
CLUTCH LEVER  
"DISENGAGED"  
POSITION  
•
DEFLECTOR  
SHIELD  
•
Repeatforoppositesideinstallinggaugewheelinsame  
adjustment hole.  
FIG. 9  
TO OPERATE ON HILLS  
GAUGE  
WHEEL  
WARNING: Do not drive up or down  
hills with slopes greater than 15° and  
do not drive across any slope.  
MOUNTING  
BRACKET  
•
Choose the slowest speed before starting up or down  
hills.  
•
•
Avoid stopping or changing speed on hills.  
If slowing is necessary, move throttle control lever to  
slower position.  
•
•
If stopping is absolutely necessary, push clutch/brake  
pedal quickly to brake position and engage parking  
brake.  
Move gearshift lever to 1st gear. Be sure you have  
allowed room for tractor to roll slightly as you restart  
movement.  
Torestartmovement, slowlyreleaseparkingbrakeand  
clutch/brake pedal.  
Make all turns slowly.  
3/8-16  
LOCKNUT  
SHOULDER  
BOLT  
3/8 WASHER  
•
•
GAUGE WHEEL  
FIG. 8  
TO TRANSPORT  
TO OPERATE MOWER (See Fig. 9)  
•
•
•
Raiseattachmentlifttohighestpositionwithattachment  
lift control.  
Yourtractor isequippedwithanoperatorpresencesensing  
switch. Any attempt by the operator to leave the seat with  
the engine running and the attachment clutch engaged  
will shut off the engine.You must remain fully and centrally  
positioned in the seat to prevent the engine from hesitating  
or cutting off when operating your equipment on rough,  
rolling terrain or hills.  
When pushing or towing your tractor, be sure gearshift  
lever is in neutral (N) position.  
Do not push or tow tractor at more than five (5) MPH.  
NOTE: To protect hood from damage when transporting  
your tractor on a truck or a trailer, be sure hood is closed  
and secured to tractor. Use an appropriate means of tying  
hood to tractor (rope, cord, etc.).  
•
•
Select desired height of cut.  
Start mower blades by engaging attachment clutch  
control.  
TOWING CARTS AND OTHER ATTACH-  
MENTS  
•
TO STOP MOWER BLADES - disengage attachment  
clutch control.  
Tow only the attachments that are recommended by and  
comply with specifications of the manufacturer of your trac-  
tor. Use common sense when towing.Too heavy of a load,  
while on a slope, is dangerous.Tires can lose traction with  
the ground and cause you to lose control of your tractor.  
CAUTION: Do not operate the mower  
without either the entire grass catcher,  
onmowerssoequipped,orthedeflector  
shield in place.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
•
Insertkeyintoignitionandturnkeyclockwiseto“START”  
BEFORE STARTING THE ENGINE  
position and release key as soon as engine starts.  
Do not run starter continuously for more than fifteen  
seconds per minute. If the engine does not start after  
several attempts, move throttle control to fast position,  
wait a few minutes and try again. If engine still does  
not start, move the throttle control back to the choke (  
) position and retry.  
CHECK ENGINE OIL LEVEL  
The engine in your tractor has been shipped, from the  
factory, already filled with summer weight oil.  
•
•
Check engine oil with tractor on level ground.  
Remove oil fill cap/dipstick and wipe clean, reinsert the  
dipstick and screw cap tight, wait for a few seconds,  
remove and read oil level. If necessary, add oil until  
“FULL” mark on dipstick is reached. Do not overfill.  
WARM WEATHER STARTING (50° F and above)  
•
When engine starts, move the throttle control to the  
fast position.  
The attachments and ground drive can now be used. If  
the engine does not accept the load, restart the engine  
and allow it to warm up for one minute using the choke  
as described above.  
•
•
For cold weather operation you should change oil for  
easier starting (See “OIL VISCOSITY CHART” in the  
Maintenance section of this manual).  
To change engine oil, see the Maintenance section in  
this manual.  
•
COLD WEATHER STARTING ( 50° F and below)  
•
ADD GASOLINE  
Whenenginestarts,allowenginetorunwiththethrottle  
control in the choke ( ) position until the engine runs  
roughly, then move throttle control to fast position.This  
may require an engine warm-up period from several  
seconds to several minutes, depending on the tem-  
perature.  
•
Fill fuel tank to bottom of filler neck. Do not overfill.  
Use fresh, clean, regular unleaded gasoline with a  
minimum of 87 octane. (Use of leaded gasoline will  
increase carbon and lead oxide deposits and reduce  
valve life). Do not mix oil with gasoline. Purchase fuel  
in quantities that can be used within 30 days to assure  
fuel freshness.  
•
The attachments can also be used during the engine  
warm-up period.  
NOTE: If at a high altitude (above 3000 feet) or in cold  
temperatures (below 32 F) the carburetor fuel mixture may  
need to be adjusted for best engine performance. See “TO  
ADJUST CARBURETOR” in the Service and Adjustments  
section of this manual.  
CAUTION: Wipe off any spilled oil or  
fuel. Do not store, spill or use gasoline  
near an open flame.  
IMPORTANT: WHEN OPERATING IN TEMPERATURES  
BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE  
GASOLINE TO HELP INSURE GOOD COLD WEATHER  
STARTING.  
CAUTION: Alcohol blended fuels (called  
gasohol or using ethanol or methanol) can at-  
tract moisture which leads to separation and  
formation of acids during storage. Acidic gas  
can damage the fuel system of an engine while  
in storage. To avoid engine problems, the fuel  
system should be emptied before storage of  
30 days or longer. Drain the gas tank, start  
the engine and let it run until the fuel lines  
and carburetor are empty. Use fresh fuel next  
season. SeeStorageInstructionsforadditional  
information. Never use engine or carburetor  
cleaner products in the fuel tank or permanent  
damage may occur.  
TO START ENGINE (See Fig. 7)  
When starting the engine for the first time or if the engine  
has run out of fuel, it will take extra cranking time to move  
fuel from the tank to the engine.  
•
Sit on seat in operating position, depress clutch/brake  
pedal and set parking brake.  
•
•
•
Place gear shift lever in neutral (N) position.  
Move attachment clutch to “DISENGAGED” position.  
Move throttle control to choke ( ) position.  
NOTE: Before starting, read the warm and cold starting  
procedures below.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
MULCHING MOWING TIPS  
MOWING TIPS  
IMPORTANT: FOR BEST PERFORMANCE, KEEP MOWER  
HOUSING FREE OF BUILT-UP GRASS AND TRASH. CLEAN  
AFTER EACH USE.  
•
Mower should be properly leveled for best mowing per-  
formance. See"TOLEVELMOWERHOUSING" in the  
Service and Adjustments section of this manual.  
The left hand side of mower should be used for trim-  
ming.  
•
The special mulching blade will recut the grass clip-  
pings many times and reduce them in size so that as  
they fall onto the lawn they will disperse into the grass  
and not be noticed. Also, the mulched grass will biode-  
grade quickly to provide nutrients for the lawn. Always  
mulch with your highest engine (blade) speed as this  
will provide the best recutting action of the blades.  
•
•
Drive so that clippings are discharged onto the area  
that has been cut. Have the cut area to the right of the  
machine. This will result in a more even distribution of  
clippings and more uniform cutting.  
•
Whenmowinglargeareas,startbyturningtotherightso  
that clippings will discharge away from shrubs, fences,  
driveways, etc. After one or two rounds, mow in the  
opposite direction making left hand turns until finished  
(See Fig. 10).  
•
Avoid cutting your lawn when it is wet. Wet grass tends  
to form clumps and interferes with the mulching action.  
The best time to mow your lawn is the early afternoon.  
At this time the grass has dried, yet the newly cut area  
will not be exposed to direct sunlight.  
•
For best results, adjust the mower cutting height so  
that the mower cuts off only the top one-third of the  
grassblades(SeeFig.11).Forextremelyheavymulch-  
ing, reduce your width of cut on each pass and mow  
slowly.  
MAX 1/3  
FIG. 10  
•
If grass is extremely tall, it should be mowed twice to  
reduce load and possible fire hazard from dried clip-  
pings. Make first cut relatively high; the second to the  
desired height.  
FIG. 11  
•
•
Certaintypesofgrassandgrassconditionsmayrequire  
that an area be mulched a second time to completely  
hide the clippings. When doing a second cut, mow  
across (perpendicular) to the first cut path.  
Change your cutting pattern from week to week. Mow  
northtosouthoneweekthenchangetoeasttowestthe  
next week. This will help prevent matting and graining  
of the lawn.  
•
•
Do not mow grass when it is wet. Wet grass will plug  
mower and leave undesirable clumps. Allow grass to  
dry before mowing.  
Always operate engine at full throttle when mow-  
ing to assure better mowing performance and proper  
discharge of material. Regulate ground speed by se-  
lecting a low enough gear to give the mower cutting  
performance as well as the quality of cut desired.  
When operating attachments, select a ground speed  
that will suit the terrain and give best performance of  
the attachment being used.  
•
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
E
E
G
S
S
MAINTENANCE SCHEDULE  
FILL IN DATES  
AS YOU COMPLETE  
S
A
R
U
R
R
U
H
U
O
T
O
C
O
A
H
S
E
5
E
R
8 H  
2
E
Y
Y
R
R
O
R
O
F
E
E
V
F
E
REGULAR SERVICE  
V
E
B
ASONSERVICE DATES  
E
E
EVERY 5  
EVE  
0
H
R
O
Y
UR  
1
E
0
S
V
0
E
H
R
O
Y
U
S
RS  
E
B
Check Brake Operation  
Check Tire Pressure  
Check Operator Presence and  
Interlock Systems  
T
Check for Loose Fasteners  
R
5
A
Sharpen/Replace Mower Blades  
3
C
Lubrication Chart  
T
Check Battery Level  
4
0
Clean Battery and Terminals  
R
Check Transaxle Cooling  
Check V-Belts  
Check Engine Oil Level  
Change Engine Oil (with oil filter)  
1,2  
Change Engine Oil (without oil filter)  
1,2  
E
Clean Air Filter  
N
2
2
G
Clean Air Screen  
I
Inspect Muffler/Spark Arrester  
N
Replace Oil Filter (If equipped)  
1,  
2
E
Clean Engine Cooling Fins  
Replace Spark Plug  
2
Replace Air Filter Paper Cartridge  
Replace Fuel Filter  
2
3 - Replace blades more often when mowing in sandy soil.  
4 - Not required if equipped with maintenance-free battery.  
5 - Tighten front axle pivot bolt to 35 ft.-lbs. maximum.  
Do not overtighten.  
1 - Change more often when operating under a heavy load or  
in high ambient temperatures.  
2 - Service more often when operating in dirty or dusty conditions.  
LUBRICATION CHART  
GENERAL RECOMMENDATIONS  
dSPINDLE ZERK  
dSPINDLE ZERK  
The warranty on this tractor does not cover items that have  
beensubjectedtooperatorabuseornegligence. Toreceive  
full value from the warranty, operator must maintain tractor  
as instructed in this manual.  
dFRONT WHEEL  
dFRONT WHEEL  
BEARING ZERK  
Some adjustments will need to be made periodically to  
properly maintain your tractor.  
BEARING ZERK  
At least once a season, check to see if you should make  
any of the adjustments described in the Service and  
Adjustments section of this manual.  
eENGINE  
• At least once a year you should replace the spark  
plug, clean or replace air filter, and check blades and  
belts for wear. A new spark plug and clean air filter  
assure proper air-fuel mixture and help your engine  
run better and last longer.  
cGEARSHIFT  
BEFORE EACH USE  
PIVOTS  
•
•
•
•
Check engine oil level.  
Check brake operation.  
Check tire pressure.  
Check operator presence and  
interlock systems for proper operation.  
Check for loose fasteners.  
cSAE 30 OR 10W30 MOTOR OIL  
dGENERAL PURPOSE GREASE  
eREFER TO MAINTENANCE “ENGINE” SECTION  
•
IMPORTANT: DO NOT OIL OR GREASE THE PIVOT POINTS WHICH  
HAVE SPECIAL NYLON BEARINGS. VISCOUS LUBRICANTS WILL  
ATTRACT DUST AND DIRT THAT WILL SHORTEN THE LIFE OF  
THE SELF-LUBRICATING BEARINGS. IF YOU FEEL THEY MUST  
BE LUBRICATED, USE ONLY A DRY, POWDERED GRAPHITE TYPE  
LUBRICANT SPARINGLY.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
TRACTOR  
Always observe safety rules when performing any main-  
tenance.  
TRAILING  
EDGE UP  
MANDREL  
ASSEMBLY  
BLADE  
2
CENTER  
HOLE  
BRAKE OPERATION  
If tractor requires more than five (5) feet to stop at highest  
speed in highest gear on a level, dry concrete or paved  
surface, then brake must be checked and adjusted.  
FLAT WASHER  
LOCK WASHER  
STAR  
TIRES  
BLADE BOLT  
•
•
•
Maintainproperairpressureinalltires(See“PRODUCT  
SPECIFICATIONS” section of this manual).  
FIG. 12  
Keep tires free of gasoline, oil, or insect control chemi-  
cals which can harm rubber.  
Avoid stumps, stones, deep ruts, sharp objects and  
other hazards that may cause tire damage.  
TO SHARPEN BLADE (See Fig. 13)  
NOTE: We do not recommend sharpening blade - but if  
you do, be sure the blade is balanced.  
Care should be taken to keep the blade balanced. An un-  
balancedbladewillcauseexcessivevibrationandeventual  
damage to mower and engine.  
NOTE: To seal tire punctures and prevent flat tires due to  
slow leaks, tire sealant may be purchased from your local  
parts dealer. Tire sealant also prevents tire dry rot and  
corrosion.  
•
The blade can be sharpened with a file or on a grind-  
ing wheel. Do not attempt to sharpen while on the  
mower.  
OPERATOR PRESENCE SYSTEM  
Besureoperatorpresenceandinterlocksystemsarework-  
ing properly. If your tractor does not function as described,  
repair the problem immediately.  
•
To check blade balance, you will need a 5/8" diameter  
steel bolt, pin, or a cone balancer. (When using a  
cone balancer, follow the instructions supplied with  
balancer.)  
•
•
•
•
The engine should not start unless the clutch/brake  
pedalisfullydepressedandattachementclutchcontrol  
is in the disengaged position.  
Whentheengineisrunning,anyattemptbytheoperator  
to leave the seat without first setting the parking brake  
should shut off the engine.  
When the engine is running and the attachment clutch  
is engaged, any attempt by the operator to leave the  
seat should shut off the engine.  
The attachment clutch should never operate unless  
the operator is in the seat.  
NOTE: Do not use a nail for balancing blade. The lobes of  
the center hole may appear to be centered, but are not.  
•
Slidebladeontoanunthreadedportionofthesteelbolt  
or pin and hold the bolt or pin parallel with the ground.  
If blade is balanced, it should remain in a horizontal  
position. If either end of the blade moves downward,  
sharpen the heavy end until the blade is balanced.  
CENTER HOLE  
BLADE  
5/8" BOLT  
OR PIN  
BLADE CARE  
Forbestresultsmowerbladesmustbekeptsharp. Replace  
bent or damaged blades.  
FIG. 13  
BLADE REMOVAL (See Fig. 12)  
BATTERY  
•
•
•
Raise mower to highest position to allow access to  
blades.  
Yourtractorhasabatterychargingsystemwhichissufficient  
for normal use. However, periodic charging of the battery  
with an automotive charger will extend its life.  
Removebladebolt,lockwasherandflatwashersecuring  
blade.  
Install new or resharpened blade with trailing edge up  
towards deck as shown.  
•
•
•
•
Keep battery and terminals clean.  
Keep battery bolts tight.  
Keep small vent holes open.  
Recharge at 6-10 amperes for 1 hour.  
IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER  
HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL  
ASSEMBLY.  
NOTE: The original equipment battery on your tractor is  
maintenance free. Do not attempt to open or remove caps  
or covers. Adding or checking level of electrolyte is not  
necessary.  
•
Reassemble blade bolt, lock washer and flat washer  
in exact order as shown.  
•
Tighten blade bolt securely (27-35 Ft. Lbs. torque).  
TO CLEAN BATTERY AND TERMINALS  
Corrosion and dirt on the battery and terminals can cause  
the battery to “leak” power.  
IMPORTANT: BLADEBOLTISHEATTREATED.IFBOLTNEEDS  
REPLACING, REPLACE ONLYWITH APPROVE BOLT SHOWN  
IN THE REPAIR PARTS.  
•
Disconnect BLACK battery cable first then RED bat-  
tery cable and remove battery from tractor.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
•
•
Rinse the battery with plain water and dry.  
OIL DRAIN VALVE  
Cleanterminalsandbatterycableendswithwirebrush  
until bright.  
•
•
Coat terminals with grease or petroleum jelly.  
Reinstall battery (See “CONNECT BATTERY” in the  
Assembly section of this manual).  
CLOSED  
AND  
LOCKED  
POSITION  
V-BELTS  
CheckV-beltsfordeteriorationandwearafter100hoursand  
replace if necessary.The belts are not adjustable.Replace  
belts if they begin to slip from wear.  
DRAIN  
TUBE  
TRANSAXLE COOLING  
Keep transaxle free from build-up of dirt and chaff which  
can restrict cooling.  
YELLOW CAP  
FIG. 15  
ENGINE  
•
Unlock drain valve by pushing inward and turning  
counterclockwise.  
To open, pull out on the drain valve.  
After oil has drained completely, close and lock the  
drain valve by pushing inward and turning clockwise  
until the pin is in the locked position as shown.  
Remove the drain tube and replace the cap onto to the  
bottom fitting of the drain valve.  
Refill engine with oil through oil fill dipstick tube. Pour  
slowly. Do not overfill. For approximate capacity see  
“PRODUCT SPECIFICATIONS” section of this man-  
ual.  
LUBRICATION  
Only use high quality detergent oil rated with API service  
classification SG-SL. Select the oil’s SAE viscosity grade  
according to your expected operating temperature.  
•
•
SAE VISCOSITY GRADES  
•
•
SAE 30  
5W-30  
-20  
0
30  
32 40  
0
100  
60  
80  
F
C
-20  
10  
-30  
-10  
20  
30  
40  
TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE  
FIG. 14  
•
Use gauge on oil fill cap/dipstick for checking level.  
Be sure dipstick cap is tightened securely for accurate  
reading. Keep oil at“FULL”line on dipstick.Tighten cap  
onto the tube securely when finished.  
NOTE: Although multi-viscosity oils (5W30, 10W30 etc.)  
improve starting in cold weather, these multi-viscosity oils  
will result in increased oil consumption when used above  
32°F. Check your engine oil level more frequently to avoid  
possible engine damage from running low on oil.  
CLEAN AIR SCREEN  
Change the oil after every 50 hours of operation or at least  
once a year if the tractor is not used for 50 hours in one  
year.  
Air screen must be kept free of dirt and chaff to prevent  
engine damage from overheating. Clean with a wire brush  
or compressed air to remove dirt and stubborn dried gum  
fibers.  
Check the crankcase oil level before starting the engine  
and after each eight (8) hours of operation. Tighten oil fill  
cap/dipstick securely each time you check the oil level.  
AIR FILTER  
Your engine will not run properly using a dirty air filter.  
Service air cleaner more often under dusty conditions.See  
Engine Manual.  
TO CHANGE ENGINE OIL (See Figs. 14 and 15)  
Determine temperature range expected before oil change.  
All oil must meet API service classification SG-SL.  
ENGINE OIL FILTER  
Replace the engine oil filter every season or every other  
oil change if the tractor is used more than 100 hours in  
one year.  
•
•
•
•
Be sure tractor is on level surface.  
Oil will drain more freely when warm.  
Catch oil in a suitable container.  
Remove oil fill cap/dipstick. Be careful not to allow dirt  
to enter the engine when changing oil.  
•
Remove yellow cap from end of drain valve and install  
the drain tube onto the fitting.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
CLEAN AIR INTAKE/COOLING AREAS  
IN-LINE FUEL FILTER (See Fig. 16)  
To insure proper cooling, make sure the grass screen,  
cooling fins, and other external surfaces of the engine are  
kept clean at all times.  
The fuel filter should be replaced once each season. If fuel  
filter becomes clogged, obstructing fuel flow to carburetor,  
replacement is required.  
•
•
•
•
With engine cool, remove filter and plug fuel line sec-  
tions.  
Place new fuel filter in position in fuel line with arrow  
pointing towards carburetor.  
Be sure there are no fuel line leaks and clamps are  
properly positioned.  
Immediately wipe up any spilled gasoline.  
Every 100 hours of operation (more often under extremely  
dusty, dirty conditions), remove the blower housing and  
other cooling shrouds. Clean the cooling fins and external  
surfaces as necessary. Make sure the cooling shrouds are  
reinstalled.  
NOTE: Operating the engine with a blocked grass screen,  
dirtyorpluggedcoolingfins,and/orcoolingshroudsremoved  
will cause engine damage due to overheating.  
CLAMP  
CLAMP  
See Engine manual.  
MUFFLER  
Inspect and replace corroded muffler and spark arrester  
(if equipped) as it could create a fire hazard and/or dam-  
age.  
FUEL  
FILTER  
SPARK PLUGS  
FIG. 16  
Replace spark plugs at the beginning of each mowing sea-  
son or after every 100 hours of use, whichever comes first.  
Spark plug type and gap setting is shown in "PRODUCT  
SPECIFICATIONS" section of this manual.  
CLEANING  
•
•
•
Clean engine, battery, seat, finish, etc. of all foreign  
matter.  
Keep finished surfaces and wheels free of all gasoline,  
oil, etc.  
Protect painted surfaces with automotive type wax.  
We do not recommend using a garden hose or pressure  
washer to clean your tractor unless the engine and trans-  
mission are covered to keep water out. Water in engine or  
transmission will shorten the useful life of your tractor. Use  
compressed air or a leaf blower to remove grass, leaves  
and trash from tractor and mower.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUST-  
MENTS:  
•
•
•
•
•
•
Depress clutch/brake pedal fully and set parking brake.  
Place gearshift lever in neutral (N) position.  
Place attachment clutch in “DISENGAGED” position.  
Turn ignition key to “STOP” and remove key.  
Make sure the blades and all moving parts have completely stopped.  
Disconnect spark plug wire from spark plug and place wire where it cannot come in contact  
with plug.  
IMPORTANT:IFANATTACHMENTOTHERTHANTHEMOWER  
DECK ISTO BE MOUNTED ONTHETRACTOR, REMOVETHE  
FRONTLINKSANDHOOKTHECLUTCHSPRINGINTOSQUARE  
TRACTOR  
TO REMOVE MOWER (See Fig. 17)  
Mower will be easier to remove from the right side of trac-  
tor.  
HOLE IN FRAME.  
TO INSTALL MOWER (See Fig. 17)  
•
•
Place attachment clutch in “DISENGAGED” position.  
Move attachment lift lever forward to lower mower to  
its lowest position.  
•
•
Raise attachment lift lever to its highest position.  
Slide mower under tractor with deflector shield to right  
side of tractor.  
•
•
Roll belt off engine pulley.  
Removesmallretainerspring,andremoveclutchspring  
off pulley bolt.  
•
•
Lower lift lever to its lowest position.  
Connect front links to mower deck and secure with  
retainer springs..  
•
•
•
•
•
Remove large retainer spring, slide collar off and push  
housing guide out of bracket.  
Disconnect anti-swaybar from chassis bracket by re-  
moving retainer spring.  
Disconnect suspension arms from rear deck brackets  
by removing retainer springs.  
Disconnect front links from deck by removing retainer  
springs.  
•
•
•
•
•
Connect suspension arms to rear deck brackets and  
secure with retainer springs.  
Connect anti-swaybar to chassis bracket and secure  
with retainer spring.  
Push clutch cable housing guide into bracket, slide col-  
lar onto guide and secure with large retainer spring.  
Place flat washer and clutch spring on idler pulley bolt  
and secure with small retainer spring.  
Raise lift lever to raise suspension arms. Slide mower  
out from under tractor.  
Install belt onto engine pulley.  
SMALL RETAINER SPRING  
CLUTCH SPRING  
SQUARE HOLE  
FLAT WASHER  
SMALL RETAINER SPRING  
SUSPENSION  
ENGINE PULLEY  
ARMS  
CLUTCH SPRING  
FRONT LINK  
RETAINER SPRING  
ANTI-SWAY BAR  
RETAINER SPRINGS  
(BOTH SIDES)  
COLLAR  
LARGE  
RETAINER  
SPRING  
HOUSING GUIDE  
BRACKET  
DEFLECTOR SHIELD  
FIG. 17  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
•
When distance “D” is 1/8" to 1/2" lower at front than  
rear, tighten nuts “F” against trunnion on both front  
links.  
To raise front of mower, loosen nut“F”from trunnion on  
both front links. Tighten nut “E” on both front links an  
equal number of turns.The two front links must remain  
equal in length.  
Whendistance“D”is1/8"to1/2"loweratfrontthanrear,  
tighten nut “F” against trunnion on both front links.  
TO LEVEL MOWER HOUSING  
Adjust the mower while tractor is parked on level ground  
or driveway. Make sure tires are properly inflated (See  
“PRODUCT SPECIFICATIONS”section of this manual). If  
tires are over or underinflated, you will not properly adjust  
your mower.  
•
SIDE-TO-SIDE ADJUSTMENT (See Figs. 18 and 19)  
•
•
•
Raise mower to its highest position.  
•
At the midpoint of both sides of mower, measure height  
from bottom edge of mower to ground. Distance “A”  
on both sides of mower should be the same or within  
1/4" of each other.  
Recheck side-to-side adjustment.  
MANDREL  
•
•
•
If adjustment is necessary, make adjustment on one  
side of mower only.  
To raise one side of mower, tighten lift link adjustment  
nut on that side.  
To lower one side of mower, loosen lift link adjustment  
nut on that side.  
“D”  
“D”  
FIG. 20  
NOTE: Each full turn of adjustment nut will change mower  
height about 1/8".  
BOTH FRONT LINKS MUST BE EQUAL IN LENGTH  
•
Recheck measurements after adjusting.  
BOTTOM EDGE  
OF MOWER TO  
GROUND  
BOTTOM EDGE  
OF MOWER TO  
GROUND  
NUT “F”  
A
A
NUT “E”  
GROUND LINE  
FIG. 18  
TRUNNION  
SUSPENSION ARM  
FRONT LINKS  
LIFT LINK  
ADJUSTMENT NUT  
FIG. 21  
TO REPLACE MOWER BLADE DRIVE BELT  
FIG. 19  
(See Fig. 22)  
FRONT-TO-BACK ADJUSTMENT (See Figs. 20and 21)  
The mower blade drive belt may be replaced without tools.  
Park the tractor on level surface. Engage parking brake.  
BELT REMOVAL -  
IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE  
FOLLOWINGFRONT-TO-BACKADJUSTMENTISNECESSARY,  
BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO  
MOWER WILL STAY LEVEL SIDE-TO-SIDE.  
•
Remove mower from tractor (See “TO REMOVE  
MOWER” in this section of this manual).  
Work belt off both mandrel pulleys and idler pulleys.  
Pull belt away from mower.  
To obtain the best cutting results, the mower housing  
should be adjusted so that the front is approximately 1/8"  
to 1/2" lower than the rear when the mower is in its high-  
est position.  
•
•
BELT INSTALLATION -  
•
•
Install new belt in reverse order of removal.  
Make sure belt is in all pulley grooves and inside all  
belt guides.  
Checkadjustmentonrightsideoftractor. Measuredistance  
“D” directly in front and behind the mandrel at bottom edge  
of mower housing as shown.  
•
Install mower in reverse order of removal instruc-  
tions.  
•
•
•
Before making any necessary adjustments, check that  
both front links are equal in length.  
If links are not equal in length, adjust one link to same  
length as other link.  
To lower front of mower loosen nut “E” on both front  
links an equal number of turns.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
WITH PARKING BRAKE “ENGAGED”  
IDLER PULLEYS  
1-1/2"  
NUT “A”  
JAM NUT  
MANDREL PULLEYS  
OPERATING ARM  
FIG. 22  
FIG. 23  
TO CHECK AND ADJUST BRAKE  
(See Fig. 23)  
Your tractor is equipped with an adjustable brake system  
which is mounted on the right side of the transaxle.  
TO REPLACE MOTION DRIVE BELT  
(See Fig. 24)  
Park the tractor on level surface. Engage parking brake.  
For assistance, there is a belt installation guide decal on  
bottom side of left footrest.  
If tractor requires more than five (5) feet to stop at highest  
speed in highest gear on a level, dry concrete or paved  
surface, then brake must be checked and adjusted.  
BELT REMOVAL -  
•
Remove mower (See “TO REMOVE MOWER” in this  
section of manual).  
TO CHECK BRAKE  
•
Park tractor on a level, dry concrete or paved surface,  
depress clutch/brake pedal all the way down and en-  
gage parking brake.  
NOTE: Observe entire motion drive belt and position of all  
belt guides and keepers.  
•
•
•
Remove belt from stationary idler and clutching idler.  
Remove belt downward from around engine pulley.  
Pull belt slack toward rear of tractor. Remove belt  
upwards from transaxle pulley by deflecting belt keep-  
ers.  
•
Place gear shift lever in neutral (N) position.  
Therearwheelsmustlockandskidwhenyoutrytomanually  
push the tractor forward.If the rear wheels rotate, the brake  
needs to be adjusted or the pads need to be replaced.  
•
Remove belt from center span keeper and pull belt  
away from tractor.  
TO ADJUST BRAKE  
•
•
•
Depress clutch/brake pedal all the way down and en-  
gage parking brake.  
BELT INSTALLATION -  
•
Measure distance between brake operating arm and  
nut “A” on brake rod.  
If distance is other than 1-1/2", loosen jam nut and turn  
nut “A” until distance becomes 1-1/2". Retighten jam  
nut against nut “A”.  
Carefully work new belt down between transaxle belt  
keepers and onto the input pulley.  
Slide belt into the center span keeper.  
Pull belt toward front of tractor and roll around the top  
groove of engine pulley.  
Install belt through stationary idler and clutching  
idler.  
Make sure belt is in all pulley grooves and inside all  
belt guides and keepers.  
Install mower (See “TO INSTALL MOWER” in this sec-  
tion of manual).  
•
•
•
Roadtesttractorforproperstoppingdistanceasstated  
above. Readjust if necessary. If stopping distance is  
still greater than five (5) feet in highest gear, further  
maintenance is necessary. Replace brake pads or  
contact a qualified service center.  
•
•
•
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
TO ADJUST STEERING WHEEL ALIGN-  
MENT  
ENGINE  
PULLEY  
If steering wheel crossbars are not horizontal (left to right)  
whenwheelsarepositionedstraightforward,removesteer-  
ing wheel and reassemble per instructions in the Assembly  
section of this manual.  
CLUTCHING  
IDLER  
STATIONARY  
IDLER  
FRONT WHEEL TOE-IN/CAMBER  
The front wheel toe-in and camber are not adjustable on  
yourtractor.Ifdamagehasoccurredtoaffectthefrontwheel  
toe-in or camber, contact your nearest authorized service  
center/department.  
CENTER SPAN  
KEEPER  
TRANSAXLE  
PULLEY  
TO REMOVE WHEEL FOR REPAIRS  
(See Fig. 26)  
•
•
Block up axle securely.  
Removeaxlecover, retainingringandwasherstoallow  
wheel removal (rear wheel contains a square key - Do  
not lose).  
FIG. 24  
•
•
Repair tire and reassemble.  
On rear wheels only: align grooves in rear wheel hub  
and axle. Insert square key.  
TRANSAXLE GEAR SHIFT LEVER NEUTRAL-  
ADJUSTMENT (See Fig. 25)  
The transaxle should be in neutral when the gear shift  
lever is in neutral (N) (lock gate) position. The adjustment  
is preset at the factory; however, if adjustment is needed,  
proceed as follows:  
•
Replace washers and snap retaining ring securely in  
axle groove.  
•
Replace axle cover.  
NOTE: To seal tire punctures and prevent flat tires due to  
slow leaks, tire sealant may be purchased from your local  
parts dealer. Tire sealant also prevents tire dry rot and  
corrosion.  
•
Make sure transaxle is in neutral (N).  
NOTE: When the tractor rear wheels move freely, the  
transaxle is in neutral.  
•
•
•
Loosen adjustment bolt in front of the right rear  
WASHERS  
RETAINING  
wheel.  
Position the gear shift lever in the neutral (N) posi-  
tion.  
Tighten adjustment bolt securely.  
RING  
AXLE  
COVER  
NOTE: Ifadditionalclearanceisneededtogettoadjustment  
bolt, move mower deck height to the lowest position.  
SQUARE KEY (REAR  
WHEEL ONLY)  
NEUTRAL  
LOCK GATE  
GEARSHIFT LEVER  
FIG. 26  
ADJUSTMENT  
BOLT  
FIG. 25  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
TO START ENGINE WITH A WEAK BATTERY  
(See Fig. 27)  
INTERLOCKS AND RELAYS  
Loose or damaged wiring may cause your tractor to run  
poorly, stop running, or prevent it from starting.  
WARNING: Lead-acid batteries gen-  
•
Check wiring. See electrical wiring diagram in the  
Repair Parts section.  
erate explosive gases. Keep sparks,  
flameandsmokingmaterialsawayfrom  
batteries. Always wear eye protection  
when around batteries.  
TO REPLACE FUSE  
Replace with 20 amp automotive-type plug-in fuse. The  
fuse holder is located behind the dash.  
If your battery is too weak to start the engine, it should be  
recharged. (See "BATTERY" in the Maintenance section  
of this manual).  
TO REMOVE HOOD AND GRILL ASSEMBLY  
(See Fig. 28)  
If “jumper cables” are used for emergency starting, follow  
this procedure:  
IMPORTANT: YOURTRACTOR IS EQUIPPEDWITH A 12VOLT  
SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT  
SYSTEM. DO NOT USEYOUR TRACTOR BATTERY TO START  
OTHER VEHICLES.  
•
•
•
Raise hood.  
Unsnap headlight wire connector.  
Stand in front of tractor. Grasp hood at sides, tilt toward  
engine and lift off of tractor.  
•
To replace, reverse above procedure.  
TO ATTACH JUMPER CABLES -  
•
Connect one end of the RED cable to the POSITIVE  
(+) terminal of each battery(A-B), taking care not to  
short against tractor chassis.  
HOOD  
•
•
ConnectoneendoftheBLACKcabletotheNEGATIVE  
(-) terminal (C) of fully charged battery.  
Connect the other end of the BLACK cable (D) to good  
chassis ground, away from fuel tank and battery.  
HEADLIGHT WIRE  
CONNECTOR  
TO REMOVE CABLES, REVERSE ORDER -  
•
BLACK cable first from chassis and then from the fully  
charged battery.  
01536  
•
RED cable last from both batteries.  
FIG. 28  
ENGINE  
TO ADJUST THROTTLE CONTROL CABLE  
The throttle control has been preset at the factory and  
adjustment should not be necessary. If adjustment is nec-  
essary, see engine manual.  
WEAK OR DEAD  
BATTERY  
FULLY CHARGED  
BATTERY  
FIG. 27  
TO ADJUST CHOKE CONTROL  
The choke control has been preset at the factory and ad-  
justment should not be necessary. If adjustment is neces-  
sary, see engne manual.  
TO REPLACE HEADLIGHT BULB  
•
•
Raise hood.  
Pull bulb holder out of the hole in the backside of the  
grill.  
•
•
Replace bulb in holder and push bulb holder securely  
back into the hole in the backside of the grill.  
Close hood.  
TO ADJUST CARBURETOR  
Your carburetor is not adjustable. If your engine does not  
operate properly due to suspected carburetor problems,  
take your tractor to an authorized service center for repair  
and/or adjustment.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STORAGE  
Immediately prepare your tractor for storage at the end  
of the season or if the tractor will not be used for 30 days  
or more.  
ENGINE  
FUEL SYSTEM  
IMPORTANT: ITISIMPORTANTTOPREVENTGUMDEPOSITS  
FROMFORMINGINESSENTIAL FUEL SYSTEM PARTS SUCH  
AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK  
DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT  
ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING  
ETHANOLORMETHANOL)CANATTRACTMOISTUREWHICH  
LEADSTOSEPARATIONANDFORMATIONOFACIDSDURING  
STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM  
OF AN ENGINE WHILE IN STORAGE.  
WARNING: Never store the tractor with  
gasoline in the tank inside a building  
where fumes may reach an open flame  
orspark. Allowtheenginetocoolbefore  
storing in any enclosure.  
TRACTOR  
•
•
•
Empty the fuel tank by starting the engine and let it run  
until the fuel lines and carburetor are empty.  
Never use engine or carburetor cleaner products in the  
fuel tank or permanent damage may occur.  
Removemowerfromtractorforwinterstorage. Whenmower  
istobestoredforaperiodoftime,cleanitthoroughly,remove  
all dirt, grease, leaves, etc. Store in a clean, dry area.  
•
Clean entire tractor (See “CLEANING” in the Mainte-  
nance section of this manual).  
Use fresh fuel next season.  
NOTE: Fuel stabilizer is an acceptable alternative in mini-  
mizing the formation of fuel gum deposits during storage.  
Add stabilizer to gasoline in fuel tank or storage container.  
Always follow the mix ratio found on stabilizer container.  
Run engine at least 10 minutes after adding stabilizer to  
allow the stabilizer to reach the carburetor. Do not empty  
the gas tank and carburetor if using fuel stabilizer.  
•
Inspect and replace belts, if necessary (See belt re-  
placement instructions in the Service and Adjustments  
section of this manual).  
•
•
Lubricate as shown in the Maintenance section of this  
manual.  
Be sure that all nuts, bolts and screws are securely  
fastened. Inspect moving parts for damage, breakage  
and wear. Replace if necessary.  
ENGINE OIL  
•
Touch up all rusted or chipped paint surfaces; sand  
lightly before painting.  
Drain oil (with engine warm) and replace with clean en-  
gine oil. (See “ENGINE” in the Maintenance section of  
this manual).  
BATTERY  
CYLINDER(S)  
•
•
Fully charge the battery for storage.  
•
•
Remove spark plug(s).  
After a period of time in storage, battery may require  
recharging.  
Pour one ounce of oil through spark plug hole(s) into  
cylinder(s).  
•
To help prevent corrosion and power leakage during  
long periods of storage, battery cables should be dis-  
connected and battery cleaned thoroughly (see “TO  
CLEAN BATTERY AND TERMINALS” in the Mainte-  
nance section of this manual).  
•
•
Turn ignition key to “START”position for a few seconds  
to distribute oil.  
Replace with new spark plug(s).  
•
•
After cleaning, leave cables disconnected and place  
cables where they cannot come in contact with battery  
terminals.  
If battery is removed from tractor for storage, do not  
store battery directly on concrete or damp surfaces.  
OTHER  
•
•
Do not store gasoline from one season to another.  
Replace your gasoline can if your can starts to rust.  
Rust and/or dirt in your gasoline will cause problems.  
•
•
If possible, store your tractor indoors and cover it to  
give protection from dust and dirt.  
Cover your tractor with a suitable protective cover that  
does not retain moisture. Do not use plastic. Plastic  
cannot breathe which allows condensation to form and  
will cause your tractor to rust.  
IMPORTANT: NEVERCOVERTRACTORWHILEENGINE AND  
EXHAUST AREAS ARE STILL WARM.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING POINTS  
PROBLEM  
CAUSE  
CORRECTION  
Will not start  
1. Out of fuel.  
1. Fill fuel tank.  
2. Engine not “CHOKED” properly.  
3. Engine flooded.  
4. Bad spark plug.  
5. Dirty air filter.  
2. See “TO START ENGINE” in Operation section.  
3. Wait several minutes before attempting to start.  
4. Replace spark plug.  
5. Clean/replace air filter.  
6. Dirty fuel filter.  
6. Replace fuel filter.  
7. Water in fuel.  
7. Empty fuel tank and carburetor, refill tank with fresh  
gasoline and replace fuel filter.  
8. Loose or damaged wiring.  
8. Check all wiring.  
9. Carburetor out of adjustment.  
9. See “To Adjust Carburetor” in Service Adjustments  
section.  
10. Engine valves out of adjustment.  
10. Contact an authorized service center/department.  
Hard to start  
1. Dirty air filter.  
1. Clean/replace air filter.  
2. Bad spark plug.  
2. Replace spark plug.  
3. Weak or dead battery.  
4. Dirty fuel filter.  
3. Recharge or replace battery.  
4. Replace fuel filter.  
5. Stale or dirty fuel.  
6. Loose or damaged wiring.  
7. Carburetor out of adjustment.  
5. Empty fuel tank and refill tank with fresh, clean gasoline.  
6. Check all wiring.  
7. See “To Adjust Carburetor” in Service Adjustments  
section.  
8. Engine valves out of adjustment.  
8. Contact an authorized service center/department.  
Engine will not turn over  
1. Clutch/brake pedal not depressed.  
2. Attachment clutch is engaged.  
3. Weak or dead battery.  
1. Depress clutch/brake pedal.  
2. Disengage attachment clutch.  
3. Recharge or replace battery.  
4. Replace fuse.  
4. Blown fuse.  
5. Corroded battery terminals.  
6. Loose or damaged wiring.  
7. Faulty ignition switch.  
8. Faulty solenoid or starter.  
9. Faulty operator presence switch(es).  
5. Clean battery terminals.  
6. Check all wiring.  
7. Check/replace ignition switch.  
8. Check/replace solenoid or starter.  
9. Contact an authorized service center/department.  
Engine clicks but will not  
start  
1. Weak or dead battery.  
1. Recharge or replace battery.  
2. Clean battery terminals.  
3. Check all wiring.  
2. Corroded battery terminals.  
3. Loose or damaged wiring.  
4. Faulty solenoid or starter.  
4. Check/replace solenoid or starter.  
Loss of power  
1. Cutting too much grass/too fast.  
2. Throttle in “CHOKE” position.  
3. Build-up of grass, leaves and trash under mower.  
4. Dirty air filter.  
1. Raise cutting height/reduce speed.  
2. Adjust throttle control.  
3. Clean underside of mower housing.  
4. Clean/replace air filter.  
5. Low oil level/dirty oil.  
6. Faulty spark plug.  
7. Dirty fuel filter.  
5. Check oil level/change oil.  
6. Clean and regap or change spark plug.  
7. Replace fuel filter.  
8. Stale or dirty fuel.  
9. Water in fuel.  
8. Empty fuel tank and refill tank with fresh, clean gasoline.  
9. Empty fuel tank and carburetor, refill tank with fresh  
gasoline and replace fuel filter.  
10. Spark plug wire loose.  
11. Dirty engine air screen/fins.  
12. Dirty/clogged muffler.  
10. Connect and tighten spark plug wire.  
11. Clean engine air screen/fins.  
12. Clean/replace muffler.  
13. Loose or damaged wiring.  
14. Carburetor out of adjustment.  
13. Check all wiring.  
14. See “To Adjust Carburetor” in Service Adjustments  
section.  
15. Engine valves out of adjustment.  
15. Contact an authorized service center/department.  
Excessive vibration  
1. Worn, bent or loose blade.  
2. Bent blade mandrel.  
1. Replace blade. Tighten blade bolt.  
2. Replace blade mandrel.  
3. Loose/damaged part(s).  
3. Tighten loose part(s). Replace damaged parts.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING POINTS  
PROBLEM  
CAUSE  
CORRECTION  
Engine continues to run  
when operator leaves seat  
with attachment clutch  
engaged  
1. Faulty operator-safety presence control system.  
1. Check wiring, switches and connections. If not  
corrected, contact an authorized service center/  
department.  
Poor cut - uneven  
1. Worn, bent or loose blade.  
2. Mower deck not level.  
1. Replace blade. Tighten blade bolt.  
2. Level mower deck.  
3. Buildup of grass, leaves, and trash under mower.  
4. Bent blade mandrel.  
3. Clean underside of mower housing.  
4. Replace blade mandrel.  
5. Clogged mower deck vent holes from buildup of  
grass, leaves, and trash around mandrels.  
5. Clean around mandrels to open vent holes.  
Mower blades will not  
rotate  
1. Obstruction in clutch mechanism.  
2. Worn/damaged mower drive belt.  
3. Frozen idler pulley.  
1. Remove obstruction.  
2. Replace mower drive belt.  
3. Replace idler pulley.  
4. Frozen blade mandrel.  
4. Replace blade mandrel.  
Poor grass discharge  
1. Engine speed too slow.  
2. Travel speed too fast.  
1. Place throttle control in “FAST” position.  
2. Shift to slower speed.  
3. Wet grass.  
4. Mower deck not level.  
3. Allow grass to dry before mowing.  
4. Level mower deck.  
5. Low/uneven tire air pressure.  
6. Worn, bent or loose blade.  
7. Buildup of grass, leaves and trash under mower.  
8. Mower drive belt worn.  
5. Check tires for proper air pressure.  
6. Replace/sharpen blade. Tighten blade bolt.  
7. Clean underside of mower housing.  
8. Replace mower drive belt.  
9. Blades improperly installed.  
10. Improper blades used.  
11. Clogged mower deck vent holes from buildup of  
grass, leaves, and trash around mandrels.  
9. Reinstall blades sharp edge down.  
10. Replace with blades listed in this manual.  
11. Clean around mandrels to open vent holes.  
Headlight(s) not working  
(if so equipped)  
1. Switch is “OFF”.  
1. Turn switch “ON”.  
2. Bulb(s) or lamp(s) burned out.  
3. Faulty light switch.  
4. Loose or damaged wiring.  
5. Blown fuse.  
2. Replace bulb(s) or lamp(s).  
3. Check/replace light switch.  
4. Check wiring and connections.  
5. Replace fuse.  
Battery will not charge  
1. Bad battery cell(s).  
1. Replace battery.  
2. Poor cable connections.  
3. Faulty regulator (if so equipped).  
4. Faulty alternator.  
2. Check/clean all connections.  
3. Replace regulator.  
4. Replace alternator.  
Engine “backfires” when  
turning engine “OFF”  
1. Engine throttle control not set between half and  
full speed (fast) position before stopping engine.  
1. Move throttle control between half and full speed  
(fast) position before stopping engine.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NO. MC17542ST (MC17542STA), PRODUCT NO. 964 77 29-03  
SCHEMATIC  
RED  
BLACK  
BATTERY  
FUSE  
RED  
RED  
A
M
STARTER  
AMMETER  
(OPTIONAL)  
BLACK  
WHITE  
SOLENOID  
RED  
S
B
M
CLUTCH / BRAKE  
(PEDAL UP)  
G
A1  
A2  
WHITE  
L
SEAT SWITCH  
(NOT OCCUPIED)  
IGNITION  
SWITCH  
WHITE  
BLACK  
BLACK  
BLACK  
BLACK  
ATT'MENT CLUTCH  
(CLUTCH OFF)  
GROUNDING  
CONNECTOR  
BLACK  
HOUR  
METER  
(OPTIONAL)  
SPARK  
PLUG  
BLACK  
IGNITION  
UNIT  
GAP  
FUEL  
LINE  
(2 PLUGS ON  
TWIN CYL. ENGINES)  
BLUE  
CHARGING SYSTEM OUTPUT  
3 AMP DC @ 3600 RPM  
28 VOLTS AC MIN. @ 3600 RPM  
(CHARGING SYSTEM DISCONNECTED)  
RED  
FUEL SHUT-OFF SOLENOID  
(IF SO EQUIPPED)  
LIGHTING SYSTEM OUTPUT  
5 AMP AC @ 3600 RPM  
ALTERNATOR  
DIODE  
ORANGE  
14 VOLTS AC MIN. @ 3600 RPM (LIGHTS OFF)  
NOTE  
YOUR TRACTOR IS  
BROWN  
BLACK  
EQUIPPED WITH A SPECIAL  
ALTERNATOR SYSTEM.  
THE LIGHTS ARE NOT  
CONNECTED TO THE  
BATTERY, BUT HAVE THEIR  
OWN ELECTRICAL SOURCE.  
BECAUSE OF THIS, THE  
HEADLIGHTS  
BRIGHTNESS OF THE LIGHTS  
WILL CHANGE WITH ENGINE  
SPEED. AT IDLE THE LIGHTS  
WILL DIM. AS THE ENGINE IS  
SPEEDED UP, THE LIGHTS  
WILL BECOME THEIR BRIGHTEST.  
NON-REMOVABLE  
CONNECTIONS  
IGNITION SWITCH  
REMOVABLE  
CONNECTIONS  
POSITION CIRCUIT “MAKE”  
WIRING INSULATED CLIPS  
OFF  
RUN/LIGHT  
M+G+A1  
B+A1  
NONE  
A2+L  
NOTE: IF WIRING INSULATED CLIPS WERE REMOVED FOR  
SERVICING OF UNIT, THEY SHOULD BE REPLACED TO  
PROPERLY SECURE YOUR WIRING.  
RUN  
B+A1  
NONE  
START B + S + A1 NONE  
02363  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NO. MC17542ST (MC17542STA), PRODUCT NO. 964 77 29-03  
ELECTRICAL  
22  
90  
21  
42  
24  
41  
43  
27  
27  
40  
26  
27  
27  
25  
16  
16  
33  
30  
D
.
C
.
A
M
P
E
R
E
S
52  
8
45  
29  
28  
27  
179720  
2
1
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NO. MC17542ST (MC17542STA), PRODUCT NO. 964 77 29-03  
ELECTRICAL  
KEY PART  
NO. NO.  
DESCRIPTION  
1
532 16 34-65 Battery  
874 76 04-12 Bolt Hex Hd 1/4-20 unc x 3/4  
532 17 66-89 Box Battery  
2
8
16  
21  
22  
24  
25  
26  
27  
28  
29  
30  
33  
40  
41  
42  
43  
45  
52  
90  
532 17 61-38 Switch Interlock  
532 18 37-59 Harness Asm Light W/4152j  
532 00 41-52 Bulb Light #1156  
532 12 47-80 Cable Battery 6 Ga. 11" red  
532 14 61-47 Cable Battery 6 Ga. 44" red w/16 wire  
532 17 51-58 Fuse  
873 51 04-00 Nut Keps Hex 1/4-20 unc  
532 12 47-73 Cable Ground 6 Ga. 12" black  
532 12 13-05 Switch Plunger Gray  
532 17 55-66 Switch Ign Delta  
532 14 04-01 Key Ign Molded Generic  
532 17 97-20 Harness Ign.  
871 11 04-08 Bolt Blk Fin Hex 1/4 - 20 x 1/2  
532 13 15-63 Cover Terminal Red  
532 17 88-61 Solenoid  
532 12 14-33 Ammeter  
532 14 19-40 Protection Wire Loop  
532 18 04-49 Cover Terminal Battery  
NOTE: All component dimensions given in U.S. inches.  
1 inch = 25.4 mm.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NO. MC17542ST (MC17542STA), PRODUCT NO. 964 77 29-03  
CHASSIS AND ENCLOSURES  
259  
264  
258  
28  
263  
17  
261  
10  
39  
18  
10  
30  
58  
278  
31  
209  
5
159  
5
209  
11  
208  
9
209  
208  
207  
64  
1
144  
13  
26  
26  
209  
60  
142  
143  
115  
144  
26  
60  
26  
142  
145  
37  
37  
114  
209  
2
211  
14  
208  
74  
38  
209  
206  
14  
38  
chassis_elite sv_pro_12  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NO. MC17542ST (MC17542STA), PRODUCT NO. 964 77 29-03  
CHASSIS AND ENCLOSURES  
KEY PART  
NO. NO.  
DESCRIPTION  
1
532 17 46-19 Chassis Stamping  
532 17 65-54 Drawbar  
2
5
9
532 15 52-72 Bumper  
532 19 32-65 Dash  
10  
11  
13  
14  
17  
18  
26  
28  
30  
31  
37  
38  
39  
58  
60  
64  
74  
872 14 06-08 Bolt Rdhd Sqnk 3/8-16 unc x 1  
532 17 49-96 Panel Dash Lh  
532 18 69-52 Panel Dash Rh  
817 49 06-08 Screw Thdrol 3/8-16 x 1/2  
532 18 65-88 Hood  
532 18 49-21 Bumper Hood  
873 80 06-00 Nut Lock w/Insert 3/8-16 unc  
532 18 82-24 Grille Lens Asm (Includes Key Nos. 258, 259, 261, 263 and 264)  
532 19 22-58 Fender  
532 13 99-76 Bracket  
817 49 05-08 Screw Thdrol 5/16-18 x 1/2  
532 17 57-10 Bracket Asm Pivot Mower Rear  
532 17 47-14 Bracket Pivot Hood  
532 15 01-27 Duct Air  
872 14 06-06 Bolt RDHD SQNK 3/8-16 x 3/4  
532 15 47-98 Dash Lower Stlt  
873 68 06-00 Nut Crownlock 3/8-16  
114 532 15 81-12 Keeper Belt Rear  
115 817 49 06-20 Screw Thdrol 3/8-16 x 1-1/4  
142 532 17 57-02 Plate Reinforcement Stlt  
143 532 18 66-89 Bracket Swaybar Chassis  
144 532 17 55-82 Bracket Ft Rest  
145 532 15 65-24 Rod Pivot Chassis Hood  
159 532 18 13-55 Cupholder  
206 532 17 01-65 Bolt Shoulder 5/16-18 TT  
207 817 67 05-08 Screw Thdrol 5/16-18 x 1/2 TYTT  
208 817 67 06-08 Screw Thdrol 3/8-16 x 1/2 TY-TT  
209 817 00 06-12 Screw 3/8-16 x 3/4  
211 532 14 52-12 Nut Hexflange Lock  
258 532 18 97-55 Lens RH  
259 532 18 97-54 Lens LH  
261 532 18 97-53 Insert, Grille  
263 532 18 38-33 Bezel RH  
264 532 18 38-32 Bezel LH  
278 532 19 16-11 Screw 10 x 3/4 Single Lead-Hex  
- -  
- -  
532 00 54-79 Plug  
532 18 78-01 Plug Dome Plastic (Choke Hole)  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NO. MC17542ST (MC17542STA), PRODUCT NO. 964 77 29-03  
DRIVE  
57  
120  
89  
69  
63  
197  
212  
81  
70  
59  
61  
116  
66  
65  
64  
84  
159  
158  
161  
198  
113  
162  
55  
56  
41  
21  
85  
112  
83  
169  
10  
14  
163  
13  
14  
112  
168  
202  
50  
18  
150  
80  
85  
4
82  
8
165  
18  
166  
38  
48  
3
51  
156  
5
11  
151  
51  
27  
49  
39  
6
79  
16  
52  
30  
32  
47  
30  
26  
6
170  
32  
52  
62  
120  
6
37  
35  
36  
77  
15  
34  
25  
28  
24  
36  
19  
26  
35  
2
53  
77  
74  
96  
26  
29  
78  
26  
76  
22  
27  
1
75  
drive-fender.stlt_38  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NO. MC17542ST (MC17542STA), PRODUCT NO. 964 77 29-03  
DRIVE  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
1
- - - - - - - - -  
Transaxle, Peerless 206-545C  
(Order Parts From Transaxle  
62  
63  
64  
65  
66  
69  
70  
74  
75  
76  
77  
78  
79  
80  
81  
82  
83  
84  
85  
89  
96  
532 12 48-72 Cover Pedal  
532 17 54-10 Engine Pulley LT/YT  
532 17 39-37 Bolt Hex  
810 04 07-00 Washer Lock Hvy Hlcl Spr 7/16  
532 15 47-78 Keeper Belt Engine Foolproof  
532 14 24-32 Screw Hex Wsh Hi-Lo 1/4-1/2 unc  
532 13 46-83 Guide Belt Mower Drive RH  
532 13 70-57 Spacer Axle  
532 12 17-49 Washer 25/32 x 1 1/4 x 16 Ga.  
812 00 00-01 E-ring #5133-75  
532 12 35-83 Key Square 2 0 x 1845/ 1865  
532 12 17-48 Washer 25/32 x 1-5/8 x 16 Ga.  
532 12 50-96 Key Woodruff #9 3/16 x 3/4  
532 14 50-90 Arm Shift  
532 16 55-92 Shaft Asm Cross Tapered  
532 16 57-11 Spring Torsion T/a  
819 17 12-16 Washer 17/32 x 3/4 x 16 Ga.  
532 16 62-31 Transaxle Link  
532 15 03-60 Nut Lock Center 1/4 - 28 FNTHD  
532 19 18-75 Console Shift STLT  
532 12 47-88 Retainer Spring 1"  
Manufactuer)  
2
532 14 66-82 Spring Return Brake T/a Zinc  
532 12 36-66 Pulley Transaxle 18" tires  
812 00 00-28 Ring Retainer # 5100-62  
532 12 15-20 Strap Torque 30 Degrees  
817 06 05-12 Screw Thdrol 5/16-18 x 3/4 TYT  
532 16 58-66 Rod Shift Fender Adjust STLT  
876 02 04-16 Pin Cotter 1/8 x 1 Cad  
532 10 57-01 Washer Plate Shf 388 Sq Hole  
874 55 04-12 Bolt 1/4-28 unf Gr. 8 W/Patch  
810 04 04-00 Washer Lock Hvy Helical 1/4  
874 49 05-44 Bolt 5/16-18 Gr. 5  
3
4
5
6
8
10  
11  
13  
14  
15  
16  
18  
19  
21  
22  
24  
25  
26  
27  
28  
29  
30  
32  
34  
35  
36  
37  
38  
39  
41  
47  
48  
49  
50  
51  
52  
53  
55  
56  
57  
59  
61  
873 80 05-00 Nut Lock Hx W/Ins 5/16-18 unc Pl  
874 78 06-16 Bolt, Fin Hex 3/8-16 unc x 1 Gr. 5  
873 80 06-00 Nut Lock 3/8-16 unc  
532 10 69-33 Knob  
532 13 08-04 Rod Brake Blk Zinc 26 840  
873 35 06-00 Nut Hex Jam 3/8-16 unc  
532 10 68-88 Spring Rod Brake 2 00 Zinc  
819 13 13-16 Washer 13/32 x 13/16 x 16 Ga  
876 02 04-12 Pin Cotter 1/8 x 3/4 Cad  
532 17 57-65 Rod Brake Parking LT/YT  
532 07 16-73 Cap Brake Parking Black  
532 16 95-92 Bracket Mtg Transaxle  
874 76 05-12 Bolt Hex Hd 5/16-18 unc x 3/4  
532 17 55-78 Shaft Asm Pedal Foot  
532 12 01-83 Bearing Nylon Blk 629 Id  
819 21 16-16 Washer 21/32 x 1 x 16 Ga  
532 12 49-63 Pin Roll 3/16 x 1"  
112 819 09 12-10 Washer 9/32 x 3/4 x 10 Ga.  
113 532 12 72-85 Strap Torque LT  
116 872 14 06-08 Bolt Rdhd Sq Neck 3/8-16 x 1  
120 873 90 06-00 Nut Lock Flg. 3/8-16  
150 532 17 54-56 Spacer Retainer  
151 819 13 32-10 Washer 13/32 x 2 x 10 Ga.  
156 532 16 60-02 Washer Srrted 5/16 ID x 1.125  
158 532 16 55-89 Bracket Shift Mount  
159 532 18 39-00 Hub Shift  
161 872 14 04-06 Bolt Rdhd Sqnk 1/4-20 x 3/4 Gr. 5  
162 873 68 04-00 Nut Crownlock 1/4-20 unc  
163 874 78 04-16 Bolt Hex Fin 1/4-20 unc x 1 Gr. 5  
165 532 16 56-23 Bracket Pivot Lever  
166 817 49 05-10 Screw 5/16-18 x 5/8  
168 532 16 54-92 Bolt Shoulder 5/16-18 x .561  
169 532 16 55-80 Plate Fastening STLT/CRD  
170 532 18 74-14 Keeper Belt T/A  
197 532 16 96-13 Nyliner Snap-In 5/8" ID  
198 532 16 95-93 Washer Nyl 7/8 Id x .105" Hyd  
202 872 11 06-14 Bolt 3/8-16 x 1-3/4 Gr 5  
212 532 14 52-12 Nut Hex Flg Lock  
532 17 91-14 Pulley Composite  
872 11 06-22 Bolt Rdhd 3/8-16 x 2-3/4 Gr. 5  
532 17 55-56 Keeper Belt Idler Flat  
532 12 77-83 Pulley Idler V Groove Plastic  
532 15 44-07 Bellcrank Clutch Grnd Drv Stl  
532 12 32-05 Retainer Belt Style Spring  
872 11 06-12 Bolt Carr. sh 3/8-16 x 1-1/2 Gr. 5  
873 68 06-00 Nut Crownlock 3/8-16 unc  
873 68 05-00 Nut Crownlock 5/16-18 unc  
532 10 57-10 Link Clutch  
532 10 57-09 Spring Return Clutch 6 75  
817 06 06-20 Screw 3/8-16 x 1-1/4  
532 13 08-01 V-Belt Ground Drive 95 25  
532 16 96-91 Keeper Belt Span Ctr  
817 12 06-14 Screw 3/8-16 x .875  
NOTE: All component dimensions give in U.S. inches.  
1 inch = 25.4 mm.  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NO. MC17542ST (MC17542STA), PRODUCT NO. 964 77 29-03  
STEERING ASSEMBLY  
38  
12  
39  
1
41  
42  
37  
37  
36  
44  
51  
54  
88  
91  
43  
71  
67  
67  
68  
46  
8
6
29  
67  
13  
65  
17  
46  
2
8
6
87  
5
87  
3
32  
5
68  
11  
4
26  
29  
43  
82  
40  
43  
95  
8
28  
30  
15  
29  
15  
15  
10  
steering_pl.lt_47  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NO. MC17542ST (MC17542STA), PRODUCT NO. 964 77 29-03  
STEERING ASSEMBLY  
KEY PART  
NO. NO.  
DESCRIPTION  
1
532 18 59-58 Wheel Steering  
2
532 18 47-06 Axle Asm  
3
532 16 98-40 Spindle Asm LH  
532 16 98-39 Spindle Asm RH  
532 12 49-31 Bearing Race Thrust Harden  
532 12 17-48 Washer 25/32 x 1-5/8 x 16 Ga.  
812 00 00-29 Ring Klip #t5304-75  
532 17 51-21 Link Drag  
4
5
6
8
10  
11  
12  
13  
15  
17  
26  
28  
29  
30  
32  
36  
37  
38  
39  
40  
41  
42  
43  
44  
46  
51  
54  
65  
67  
68  
71  
82  
88  
87  
91  
95  
810 04 06-00 Washer Lock Hvy Hlcl Spr 3/8  
873 94 08-00 Nut Hex Jam Toplock 1/2-20 unf  
532 13 65-18 Spacer Brg Axle Front  
532 14 52-12 Nut Hex Flange Lock  
532 18 06-41 Shaft Asm Strg  
532 12 68-47 Bushing Link Drag Blk LR  
819 13 14-16 Washer 13/32 x 7/8 x 16 Ga.  
817 00 06-12 Screw 3/8-16 x 3/4  
876 02 04-12 Pin Cotter 1/8 x 3/4 Cad  
532 13 04-65 Rod Tie Wire Form 19 75 Mech  
532 15 50-99 Bushing Strg  
532 15 29-27 Screw  
532 17 20-93 Cap Wheel Steering  
819 18 24-11 Washer 9/16 x 1-1/2 11 Ga.  
873 54 06-00 Lock nut  
532 15 99-45 Adaptor Wheel Strg  
532 16 96-33 Boot Steering Shaft  
532 12 17-49 Washer 25/32 x 1 1/4 x 16 Ga.  
532 18 06-40 Extension Steering Shaft LR/LT  
532 12 12-32 Cap Spindle Fr Top Blk  
873 54 04-00 Nut Crownlock 1/4-28  
871 13 04-20 Bolt Hex 1/4-28 unf x 1-1/4 Gr. 8  
532 16 03-67 Spacer Brace Axle  
872 11 06-18 Bolt Rdhd Sq 3/8-16 x 2-1/4  
532 16 98-27 Axle, Brace  
532 17 51-46 Steering Asm  
532 16 98-35 Bracket Susp Chassis Front  
532 17 51-18 Bolt Shoulder 7/16-20  
532 17 39-66 Washer Flat .781 x 1-1/2 x .14  
532 17 55-53 Clip Steering  
532 18 89-67 Washer Hardened  
NOTE: All component dimensions given in U.S. inches.  
1 inch = 25.4 mm.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NO. MC17542ST (MC17542STA), PRODUCT NO. 964 77 29-03  
SEAT ASSEMBLY  
1
8
9
8
14  
9
7
7
10  
5
6
22  
21  
2
24  
5
16  
15  
11  
4
13  
17  
3
12  
seat_lt.knob_9  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
13  
14  
15  
16  
17  
21  
22  
24  
25  
532 12 12-48 Bushing Snap Blk Nyl 50 Id  
872 05 04-12 Bolt Rdhd Sqnk 1/4-20 x 1-1/2  
532 13 43-00 Spacer Split 28 x 96 Yel Zinc  
532 12 12-50 Spring Cprsn 1 27 Blk Pnt  
532 12 39-76 Nut Lock 1/4 Lge Flg Gr. 5 Zinc  
532 17 18-52 Bolt Shoulder 5/16-18 unc-2A  
873 80 05-00 Nut Hex Lock W/Ins 5/16-18  
819 17 19-12 Washer 17/32 x 1-3/16 x 12 Ga.  
532 12 70-18 Bolt Shoulder 5/16-18 x 62  
1
532 18 87-05 Seat  
2
532 18 01-66 Bracket Pivot Seat  
3
871 11 06-16 Bolt Fin Hex 3/8-16 unc x 1  
819 13 16-10 Washer 13/32 x 1 x 10 Ga.  
532 14 50-06 Clip Push-In  
4
5
6
873 80 06-00 Nut Hex w/Ins. 3/8-16 unc  
7
532 12 41-81 Spring Seat Cprsn 2 250 Blk Zi  
817 00 06-16 Screw 3/8-16 x 1  
819 13 16-14 Washer 13/32 x 1 x 14 Ga.  
532 18 01-86 Pan Seat  
8
9
10  
11  
12  
532 16 63-69 Knob Seat  
532 12 12-46 Bracket Mounting Switch  
NOTE: All component dimensions given in U.S. inches.  
1 inch = 25.4 mm  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NO. MC17542ST (MC17542STA), PRODUCT NO. 964 77 29-03  
DECALS  
12  
3
3
10  
20  
4
3
1
7
8
11  
2
6
8
14  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
1
532 15 63-68 Decal Oper.  
11  
12  
14  
20  
- -  
- -  
- -  
- -  
532 16 88-69 Decal Tick Mark  
2
532 17 35-87 Decal Reflector RH  
532 19 32-03 Decal Hood RH  
532 19 32-08 Decal Fender  
532 18 57-33 Decal Steering Wheel  
532 16 03-96 Decal V-Belt Schematic  
532 14 50-05 Decal Bat Dan/Psn  
532 13 83-11 Decal Handle Lft Height Adjust  
532 18 82-53 Pad Footrest RH  
3
4
5
532 19 40-80 Decal Side Panel  
532 19 32-10 Decal Engine  
532 17 91-28 Decal Deck B 42  
532 17 35-89 Decal Reflector LH  
532 15 70-02 Decal Fender Danger  
6
7
532 18 82-52 Pad Footrest LH  
532 19 31-90 Manual Owner's (English)  
8
10  
KEY PART  
NO. NO.  
WHEELS & TIRES  
DESCRIPTION  
1
1
532 05 91-92 Cap Valve Tire  
2
5,8  
2
532 06 51-39 Stem Valve  
3
4
532 10 62-22 Tire F Ts 15 x 6.0 - 6 Service  
532 05 99-04 Tube Front (Service Item Only)  
532 12 51-21 Rim Asm 6" front Service  
532 12 49-57 Fitting Grease (Front Wheel Only)  
532 12 49-59 Bearing Flange (Front Wheel Only)  
532 12 51-22 Rim Asm 8" rear Service  
532 13 84-68 Tire R Ts 20 x 8-8 C Service  
532 12 49-26 Tube Rear (Service Item Only)  
532 19 32-68 Cap Axle  
4,10  
7
5
6
3,9  
7
6
11  
8
9
10  
11  
- -  
532 14 43-34 Sealant, Tire (10 oz. Tube)  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
wheel_1  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NO. MC17542ST (MC17542STA), PRODUCT NO. 964 77 29-03  
ENGINE  
3
2
72  
62  
1
81  
13  
4
78  
38  
32  
14  
44  
46  
78  
33  
37  
31  
33  
45  
29  
23  
OPTIONAL EQUIPMENT  
Spark Arrester  
engine-bs.1cyl_48  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
1
2
3
532 17 05-51 Control Throttle/Choke  
37  
38  
44  
45  
46  
62  
72  
78  
81  
532 13 70-40 Line Fuel 20"  
817 72 04-08 Screw Hex Thd Cut 1/4-20 x 1/2  
532 18 16-54 Plug Drain Oil Easy  
- - - - - - - -  
Engine, Briggs 31G777  
(Order parts from engine manu-  
facturer)  
817 67 04-12 Screw Hexwsh Thdrol 1/4-20 x 3/4  
817 00 06-12 Screw Hexwsh Thdr 3/8-16 x 3/4  
819 09 14-16 Washer 9/32 x 7/8 x 16 Ga.  
810 01 05-00 Washer Split  
871 07 05-12 Screw Hex Head Cap 5/16-18 x 3/4  
817 06 06-20 Screw 3/8-16 x 1-1/4 SMGML  
873 51 04-00 Nut Keps Hex 1/4-20 unc  
4
532 13 73-52 Muffler  
532 16 52-91 Gasket Eng  
13  
14  
23  
29  
31  
32  
33  
532 14 84-56 Tube Drain Oil Easy  
532 16 98-37 Shield Brn/Dbr Guard  
532 13 71-80 Kit Spark Arrestor (Flat Scrn)  
532 18 55-34 Tank Fuel  
532 14 05-27 Cap Asm Fuel W/sym Vented  
532 12 34-87 Clamp Hose Black  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NO. MC17542ST (MC17542STA), PRODUCT NO. 964 77 29-03  
MOWER LIFT  
7
8
5
1
3
13  
2
4
6
6
11  
5
4
12  
13  
19  
20  
20  
13  
18  
17  
16  
15  
20  
31  
32  
19  
20  
15  
13  
31  
32  
lift-rh.1piece_3  
KEY  
NO.  
PART  
NO.  
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
DESCRIPTION  
1
2
3
4
5
6
7
8
532 15 94-61 Wire Asm Inner W/plunger LT  
532 15 94-76 Shaft Asm Lift  
15 532 17 32-88 Link Front  
16 873 35 08-00 Nut Jam Hex 1/2-13 unc  
17 532 17 56-89 Trunnion  
532 18 88-22 Pin Groove  
812 00 00-02 E Ring #5133-62  
18 873 80 08-00 Nut Lock W/Wsh 1/2-13 unc  
19 532 13 98-68 Arm Suspension Rear  
20 532 16 35-52 Spring, Retainer  
31 532 16 98-65 Bearing Pvt. Lift  
819 21 16-21 Washer PLTD 21/32 x 1 x 21 Ga.  
532 12 01-83 Bearing Nylon Blk 629 Id  
532 12 56-31 Grip Handle  
532 12 45-26 Button Plunger Black  
32 873 54 06-00 Nut Crownlock 3/8-24  
11 532 13 98-65 Link Lift LH  
12 532 13 98-66 Link Lift RH  
13 532 12 46-70 Retainer Spring  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NO. MC17542ST (MC17542STA), PRODUCT NO. 964 77 29-03  
MOWER DECK  
67  
68  
158  
40  
185  
36  
40  
143  
152  
45  
150  
144  
159  
46  
40  
105  
106  
103  
104  
106  
105  
102  
145  
184  
59  
148  
104  
103  
44  
21  
56  
55  
53  
52  
111  
113  
116  
101  
146  
2
33  
32  
31  
48  
54  
102  
117  
142  
147  
119  
30  
118  
34  
21  
2
21  
112  
21  
118  
117  
119  
113  
21  
1
147  
116  
2
21  
142  
23  
24  
25  
26  
2
16  
28  
15  
14  
27  
20  
18  
130  
29  
131  
129  
92  
149  
92  
3
18  
4
13  
5
6
11  
10  
9
19  
21  
8
42_D_man-t-path_stlt_3  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NO. MC17542ST (MC17542STA), PRODUCT NO. 964 77 29-03  
MOWER DECK  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
67  
68  
92  
532 17 15-98 Knob  
1
532 16 58-92 Deck Asm MWR 42"weldment  
872 14 05-06 Bolt Rdhd Sqnk 5/16-18 unc x 3/4  
532 13 80-17 Bracket Asm Fr Sway Bar 38/42  
532 16 54-60 Bracket Asm Deck 42"sway Bar  
532 12 46-70 Retainer Spring  
532 14 49-59 V-Belt Mower 42"  
873 80 06-00 Nut 3/8-16 unc  
2
3
101 532 13 64-20 Cover Mulching  
4
102 871 08 10-10 Screw 10-24 x 5/8  
103 819 06 12-16 Washer #10  
104 810 07 10-00 Washer Lock #10  
105 532 16 07-93 Latch Asm.  
106 532 12 50-04 Nut Weld  
5
6
532 17 80-24 Deck Sway Bar  
8
532 85 08-57 Bolt 3/8 - 24 x 1.25 Gr. 8  
810 03 06-00 Washer Lock Hvy 3/8  
532 14 02-96 Washer Hard Blade Mower Vented  
532 13 41-49 Blade Mower 42"  
532 13 76-45 Shaft Asm W/lower Bearing  
532 12 87-74 Housing Mandrel Vented  
532 11 04-85 Bearing Ball Mandrel  
532 17 44-93 Stripper Mower  
9
10  
11  
13  
14  
15  
16  
18  
19  
20  
21  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
36  
40  
44  
45  
46  
48  
52  
53  
54  
55  
56  
59  
111 532 17 92-92 Bracket Wheel Guage LH  
112 532 17 92-93 Bracket Wheel Guage RH  
113 817 00 05-10 Bolt 5/16-18 Hex Whs-Hd Lck Ser.  
116 532 12 48-42 Bolt Shoulder  
117 532 18 86-06 Wheel Guage  
118 873 93 06-00 Nut Lock 3/8-16 unc  
119 819 12 14-14 Washer 3/8 x 7/8 x 14 Ga.  
129 819 13 13-12 Washer 13/32 x 13/16 x 12 Ga.  
130 874 78 06-16 Bolt 3/8-16 x 1 Gr. 5  
131 872 14 06-08 Bolt 3/8-16 x 1  
872 14 05-05 Bolt Rdhd Sqnk 5/16-18 x 5/8  
532 13 28-27 Bolt Shoulder  
532 15 97-70 Baffle Vortex 42  
873 68 05-00 Nut Crownlock 5/16-18 unc  
532 17 75-63 Bracket Deflector Mower 42"  
532 10 53-04 Cap Sleeve 80 x 112 Blk Mower  
532 12 37-13 Spring Torsion Deflector 2 52  
532 11 04-52 Nut Push Phos & Oil  
532 17 18-59 Shield Deflector Mower 42" Blk  
819 11 10-16 Washer 11/32 x 5/8 x 16 Ga.  
532 13 14-91 Rod Hinge 42" 6 75 Wlg  
532 17 39-84 Screw Thd Rolling  
142 532 16 58-90 Arm Spring Brake Mower  
143 532 15 71-09 Bracket Arm Idler 42"  
144 532 17 34-41 Keeper Belt 42" Clutch  
145 532 17 34-37 Pulley Idler Flat  
146 532 17 34-43 Bolt Carriage Idler  
147 532 13 13-35 Spring Extension  
148 532 16 90-22 Spring Return Idler  
149 532 16 58-98 Retainer Spring Yellow  
150 819 09 12-10 Washer 9/32 x 3/4 x 10 Ga.  
152 532 16 96-76 Clutch Cable 42"  
532 18 76-90 Washer Spacer  
532 17 34-36 Pulley Mandrel 42"  
532 17 83-42 Nut Toplock Flng  
158 817 72 04-08 Screw Hex Thd Cut 1/4-20 x 1/2  
159 872 14 06-14 Bolt Rdhd Sqn 3/8-16 unc x 1-3/4  
184 819 13 14-10 Washer 13/32 x 7/8 x 10 Ga.  
185 532 18 82-34 Head Asm. Cable Clutch  
872 11 06-12 Bolt Rdhd 3/8-16 unc x 1-1/2 Gr. 5  
532 17 34-38 Pulley Idler Flat  
873 90 06-00 Nut Lock 3/8-16 unc  
532 14 00-88 Guard Mandrel LH Black  
532 12 47-88 Spring Retainer 1" Zinc/cad  
532 13 77-29 Screw Hex Thd Cut 1/4-20 x 5/8 T  
532 13 39-44 Washer Hardened Smaller  
532 13 98-88 Bolt Shoulder 5/16-18 unc Blkz  
532 18 49-07 Arm Asm Pad Brake  
- -  
532 13 07-94 Mandrel Assembly(Includes Hous-  
ing, Shaft and Shaft Hardware  
Only-Pulley not Included)  
532 16 95-83 Replacement Mower, Complete  
(Std. Deck - Order separately  
gauge wheel and mulch cover  
components key nos. 116-119  
and 101-106)  
- -  
532 17 85-15 Washer Hardened  
532 15 50-46 Arm Idler 42"mower LT/YT  
532 12 20-52 Spacer Retainer Mower  
532 17 34-42 Guard TUV Idler  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE  
®
®
POLICY  
WARRANTY  
Issued January 1980  
Revised January 1991  
LIMITED WARRANTIES  
FOR  
NEW PEERLESS GEAR POWER TRAIN COMPONENTS  
A. Products Warranted  
Peerless Gear and Machine Division of Tecumseh Products Company (“Tecumseh”), subject to the limitations contained below,  
will,at its option, repair or replace, without charge for parts or labor only, any part of a new Power Train Component (which as used  
herein means and includes the transaxle, gear box, transmission, differential and right angle drives, and any part of the Power Train  
Component), EXCEPT any new Power Train Component incorporated in equipment used for commercial or rental purposes, which is  
found upon examination by any Tecumseh Authorized Service Outlet or by Tecumseh’s factory in Grafton, Wisconsin, to be DEFECTIVE  
IN MATERIAL AND/OR WORKMANSHIP if received by Tecumseh or a Tecumseh Authorized Service Outlet for such examination within  
TWO YEARS from the date of sale to the original consumer purchaser of Peerless Series 820, 900, 910, 915, 920, 930 transaxles and  
Series 1100 angle drive and ONEYEAR for all other Peerless products. New Power Train Components incorporated in equipment used  
for commercial purposes are warranted in the same manner and to the same extent EXCEPT such Power Train Components are war-  
ranted for NINETY (90) DAYS ONLY, and must be received by Tecumseh or by a Tecumseh Authorized Service Outlet for such examina-  
tion within 90 days from the date of sale to the original purchaser. New Power Train Components Incorporated in equipment used for  
rental purposes are warranted in the same manner and to the same extent EXCEPT such Power Train Components are warranted for  
THIRTY (30) DAYS ONLY, and must be received by Tecumseh or a Tecumseh Authorized Service Outlet within 30 days from the date  
of sale to the original purchaser.  
B. Products And Items Not Warranted  
1. Alterations or Modifications of Power Train Components.  
2. Accidents, Normal Maintenance, Failure to follow the Original Equipment Manufacturer’s Manual.  
This warranty covers only parts of new Power Train Components which are found upon examination to be defective in material or  
workmanship as delivered to the original purchaser. This warranty does not cover defects caused by depreciation or damage caused  
by normal wear, accidents, improper maintenance, improper use or abuse of the product, failure to follow the instructions contained in  
an Instruction Manual for the operation of the Power Train Component and parts. The cost of normal maintenance and replacement of  
service items which are not defective shall be paid for by the original purchaser.  
C. Securing Warranty Service  
Warranty service can be arranged for by contacting either aTecumseh Authorized Service Outlet (anyTecumseh Registered Service  
Dealer, Tecumseh Authorized Service Distributor, or Tecumseh Central Warehouse Distributor) or by contacting Tecumseh, c/o Service  
Manager, Engine and Transmission Group Service Division, 900 North Street, Grafton, Wisconsin 53024. Warranty service can only  
be performed by a Tecumseh Authorized Service Outlet or by Tecumseh at its factory in Grafton, Wisconsin. At the time of requesting  
warranty service, evidence must be presented of the date of sale to the original purchaser. The purchaser shall pay any charges for  
making service calls and/or for transporting the product to and from the place where the inspection and/or warranty work is performed.  
The purchaser shall be responsible for any damage or loss incurred in connection with the transportation of Power Train Components  
and/or part(s) of the Power Train Components submitted for inspection and/or warranty work.  
D. Limitation of Damages and Implied Warranties  
The foregoing EXPRESSED WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES. Neither Tecumseh nor any of its  
affiliates makes any warranties, representations or promises, written or oral, as to the quality of the Power Train Component or any of  
its parts, other than as set forth herein.  
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, TO THE EXTENT THAT  
EITHER MAY APPLY TO ANY PART(S) OF POWER TRAIN COMPONENTS, SHALL BE LIMITED IN DURATION TO THE PERIODS  
OF THE EXPRESSED WARRANTIES DEFINED IN PARAGRAPH A HEREOF. IN NO EVENT WILL TECUMSEH BE LIABLE FOR ANY  
INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES AND/OR EXPENSES. Some states do not allow limitations on how long  
an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitation(s) or exclusion(s)  
may not apply to you. This warranty gives you specific legal rights and you may also have other legal rights which vary from state to  
state.  
E. No Dealer Warranty  
Tecumseh neither assumes nor authorizes any other person, natural or corporate, to assume for Tecumseh any other obligations or  
liabilities in connection with or with respect to any part(s) of a Power Train Component. The seller or dealer of part(s) of a Power Train  
Component has no authority, whatsoever, to make any representations or promises on behalf of Tecumseh or to modify the terms or  
limitations of Tecumseh’s warranty in any way.  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION  
ONLY RIDE UP AND DOWN HILL,  
NOT ACROSS HILL  
15 DEGREES MAX.  
WARNING: To avoid serious injury, operate your tractor up and  
down the face of slopes, never across the face. Do not mow  
slopes greater than 15 degrees. Make turns gradually to prevent  
tipping or loss of control. Exercise extreme caution when  
changing direction on slopes.  
1. Fold this page along dotted line indicated above.  
2. Hold page before you so that its left edge is vertically parallel to a tree  
trunk or other upright structure.  
3. Sight across the fold in the direction of hill slope you want to measure.  
4. Compare the angle of the fold with the slope of the hill.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Craftsman Lawn Aerator 48624218 User Guide
Land Pride Lawn Mower RBT40108 User Guide
Snapper Lawn Aerator 4534 User Guide
Snapper Lawn Mower Accessory 1721301 02 User Manual
Snapper Lawn Mower CP21507R User Manual
Snapper Lawn Mower E281016BE User Manual
Snapper Lawn Mower SPV22675HWFC 7800264 User Manual
Swisher Lawn Mower WB924 User Guide
Weed Eater Lawn Mower 174193 User Guide
White Lawn Mower 122 528R190 User Guide