MEY Equipment Lawn Mower 26TCVM User Guide

OWNER’S MANUAL  
26” Twin Clutch  
VERTIMOWER  
Model No. 26TCVM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY INSTRUCTIONS  
Please read before using vertimower.  
Never vertimow while barefoot or wearing open sandals or thongs. Wear long trousers and strong  
protective shoes.  
Know your controls. Learn how to stop the engine quickly in any emergency.  
Make sure the lawn is clear of sticks, stones, bones, wire and any debris, as they could be picked up  
and thrown by the blades.  
Stop the engine and disconnect the spark plug cap before clearing blockages, checking or working on  
the vertimower.  
Before using, always visually inspect to see that the blades are not worn or damaged.  
Check all nuts, bolts and screws often; always be sure the vertimower is in safe operating condition.  
Use only genuine replacement parts.  
Refuel outdoors only. Do not smoke while fueling engine. Add fuel before starting engine. Never  
remove the cap off the fuel tank or add fuel while the engine is running or the engine is hot. If fuel is  
spilled, do not attempt to start the engine but move machine away from the area of the spill and avoid  
creating any source of ignition until fuel vapours have dissipated.  
Do not vertimow whilst people, especially children or pets are in the mowing area.  
Replace worn or faulty silencers.  
Vertimow only in good daylight.  
Never use the vertimower unless all guards provided by the manufacturer are in position.  
Start the engine carefully with hands and feet well away from the blades.  
Do not operate in a confined space where exhaust fumes (carbon monoxide) can collect.  
Stop the engine whenever you leave the machine.  
Do not allow children or people unfamiliar with these instructions to use the vertimower.  
Store the vertimower in a well ventilated room away from naked flames such as may be found in hot  
water heaters.  
Do not over speed the engine or alter governor settings. Excessive speed is dangerous and shortens  
vertimower life.  
It is advisable to wear suitable eye protection when operating a vertimower.  
Turn the fuel off at the conclusion of vertimowing and reduce the throttle setting during engine run-  
out.  
Store fuel in cool place in a container specifically designed for the purpose. In general, plastic  
containers are unsuitable.  
Stop the engine, disconnect the spark plug cap and inspect the mower if: (a) the machine begins to  
vibrate abnormally; or (b) after striking a foreign object.  
Never vertimow while walking backwards.  
Disengage the blades before pushing vertimower across gravel drives, walks or roads.  
Walk, never run.  
Vertiimow across the face of slopes, never up and down. Exercise extreme caution when changing  
direction slopes. Do not vertimow excessively steep slopes.  
M.E.Y. Equipment – 26” Twin Clutch VERTIMOWER  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
SETTING UP THE VERTIMOWER  
To obtain an even depth of cut, setting up the vertimower correctly is important  
and the following procedure is recommended.  
Turn off petrol.  
Turn engine to Top Dead Centre (TDC).  
Lay back mower on 20 ltr drum or catcher.  
Place straight edge between back and front rollers, chain case side.  
Measure from tip of blade to straight edge and adjust front roller to the desired  
cutting depth - normally the first pass might be at -2mm and then the cam adjuster  
would allow this to be increased to -6mm  
Check alignment of front roller to cutting blade and adjust front roller  
accordingly.  
Rub chalk on back roller.  
Check back roller alignment to front roller.  
Adjust back roller accordingly by rotating the back roller cam.  
Re-check height on chain case side using your straight edge.  
OPERATING RECOMMENDATIONS  
We recommend that the following checks be made before operation of the vertimower:-  
Check engine oil level - top up with manufacturer’s recommended lubricant.  
Check that the air filter is clean - follow manufacturer’s recommendations.  
Grease the nipples on the drive shaft bearings.  
Oil the cutter clutch, remove the slotted countersunk screw from the female  
clutch cone and add a couple of drops of light engine oil, add two or three drops  
of oil through the male clutch cone hole between the clutch forks ( you may need  
to rotate either of the cones for the lubrication points to be readily accessible).  
Adjust the cutter reel height to the required first cut depth - see section on height  
adjustment.  
Lubricate the chains on a regular basis with good quality chain oil.  
Check that all the vertimower’s bolts are secure.  
M.E.Y. Equipment – 26” Twin Clutch VERTIMOWER  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
MOWER CARE TIPS  
When cleaning the mower, avoid using pressure hoses of air or water which may  
force grit into the bearings, oiled clutch and the engine.  
The twin clutch enables the cutter reel to be stationary when moving over hard  
paved areas and for loading. This minimises accidental blade damage from hard  
objects.  
The M.E.Y. Vertimower has been designed to throw approximately 75% of the  
grass The motor should not be inclined more than 45° when adjusting the blade  
setting, servicing the machine or loading it onto trailers or other transport. This is  
to prevent sump oil entering the cylinder or carburetor.  
When using a ramp to load the mower for transportation, avoid exposed nuts or  
steel fastenings that may damage the blade or cause the rear roller to skid out of  
control.  
clippings into the catcher. The deflector can be adjusted to maximise the  
performance.  
CLUTCH CONTROLS  
All vertimowers are fitted with two clutches which enables either the back roller drive or  
the cutter reel to be used individually or both together. Ensure that the vertimower blades  
are lifted above the ground before testing the cutter clutch.  
CUTTING HEIGHT ADJUSTMENT  
The front roller side plates are secured by two pivot point nuts and two locking bolts with  
nuts operating in a radiused slot. By loosening these four nuts, the front roller can be  
moved to increase or decrease the cutter depth. A straight edge can be used to measure  
the required setting.  
In addition, a quick cam height adjuster is fitted to provide up to 4mm variation. The  
special spanner provided with the vertimower can be used to free off the roller end bolts  
and the cams can then be rotated. 90° represents 2mm and the full 180° gives 4mm  
change. It is essential that the cams are set at the same position each end to provide an  
even cut. Both end bolts need to be secured prior to operating the vertimower.  
M.E.Y. Equipment – 26” Twin Clutch VERTIMOWER  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
CUTTING REEL  
Vertimowers can be fitted with a choice of blades:-  
2 Tooth Crinolin spring steel blades are normally fitted as standard. They can  
be reversed by removing the reel, removing the bearing housings, removing the  
nyloc nut and all the blades with their spacers. The reel can then be reassembled  
presenting the back edge as the new cutting face. Note the alternating pattern of  
the blades on the shaft.  
2 Tooth Tungsten Tipped blades wear better but cost more and are easily  
damaged by impact with solid objects such as concrete or paving. These are  
preferred by experienced operators with a large workload.  
9 Tooth Tungsten Tipped blades are available and recommended for regular use  
on hardened fine turf surfaces such as tennis courts, bowling greens or cricket  
wickets. Smaller spacers can be used in this application to increase the number of  
blades in the reel.  
TO REMOVE CUTTER REEL  
Remove the dummy sole plate by removing the two side bolts at each end.  
Remove cutter reel chain.  
Remove sprocket boss (NOTE: left-hand thread).  
Remove bolts securing bearing housings and the two safety stop square headed  
bolts these prevent the reel being raised to the point where the blades destroy the  
deflector.  
Pull out cutter reel through the bottom.  
Check condition of bearings and replace if necessary.  
Replace the cutter reel in the machine and refit the four side bolts.  
Refit dummy sole plate ensuring that the deflector is secured within the two  
locating tabs.  
Adjust cutter reel down to closely miss the dummy sole plate. Then fit the two  
safety stop bolts.  
Refit sprocket boss, cutter chain and lubricate chains.  
Check the tension of the two drive chains and adjust if required and replace the  
chain case.  
Check all bolts are secure and then test run machine.  
M.E.Y. Equipment – 26” Twin Clutch VERTIMOWER  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
BACK ROLLER  
The back rollers are fabricated from thick line pipe, rolled on both ends to prevent  
scuffing and mounted on discs secured to a main drive shaft rotating on sealed ball  
bearings with machined steel bearing housings. The drive is through a 35 tooth sprocket  
on the chain case side.  
TO REMOVE THE BACK ROLLER  
Turn off petrol.  
Remove chain case.  
Remove back roller chain.  
Remove back roller sprocket (left-hand thread) if required.  
Remove small cover plate behind the 35 tooth sprocket.  
Lift machine forward and lean petrol tank on 20 litre drum or lift handles.  
Remove bearing housing bolts and this will release the rear roller including the  
sprocket.  
Lift out back roller from chassis.  
Service bearings and roller as found necessary.  
Refit roller, bearing bolts and cover plate in side case.  
Lift mower back taking care not to drop on the back roller.  
Refit drive sprocket (knock up tight).  
Refit chain and adjust.  
Refit chain case and seal.  
Check alignment and use the cam nut on the non chaincase sideplate to adjust as  
required.  
VERTIMOWING  
As the name suggests, the machine is designed to cut or ‘mow’ the grass vertically. The  
process aims to free the root base of thatch which restricts water, and nutrient penetration.  
The M.E.Y. vertimower has not been designed as a tiller! Depending on the turf  
condition, one might expect the blades to penetrate 10mm into the soil. The life of the  
blades will be directly related to the depth of cut and the soil hardness. Watering the  
surface on the night before can greatly ease the blade wear.  
Scarifiers are available for slicing the turf root system to depths of say 40mm.  
M.E.Y. Equipment – 26” Twin Clutch VERTIMOWER  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE NOTES:-  
(Servicing, Oil Changes, Bearing Replacements etc.)  
200 COLLIER ROAD  
BAYSWATER WA 6053  
TEL 08 9370 1110  
Fax 08 9370 2566  
M.E.Y. Equipment – 26” Twin Clutch VERTIMOWER  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  

Ames True Temper Lawn Mower M5SNT User Guide
Dixon Lawn Mower Ram Ultra 25 User Guide
McCulloch Lawn Mower MFT44 154 User Guide
Sears Lawn Mower Accessory 917_249491 User Manual
Snapper Lawn Mower 1690043 User Guide
Snapper Lawn Mower DLW359T User Manual
Snapper Lawn Mower NZM21522KWV NZM19482KWV NZM25612KWV NZM27612KH User Manual
Snapper Lawn Mower SPV21675FC SPV21675EFC User Manual
Snapper Lawn Mower WMR216517B WMRP216517B User Manual
White Lawn Mower 11A 702A190 User Guide