Soil Pulverizers
SP2060, SP2072, SP3072 & SP3084
SP20 Series
30154
SP30 Series
30155
307-099M
Operator’s Manual
Read the Operator’s Manual entirely. When you
see this symbol, the subsequent instructions and
warnings are serious - follow without exception.
Your life and the lives of others depend on it!
!
Cover photo may show optional equipment
not supplied with standard unit.
7/11/12
© Copyright 2012 Printed
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ
Important Safety Information
Important Safety Information
These are common practices that may or may not be applicable to the products described in
this manual.
Look For The Safety Alert Symbol
Safety at All Times
The SAFETY ALERT SYMBOL indicates there is a
potential hazard to personal safety involved and extra
safety precaution must be taken. When you see this
symbol, be alert and carefully read the message that
follows it. In addition to design and configuration of
equipment, hazard control, and accident prevention
are dependent upon the awareness, concern,
prudence, and proper training of personnel involved
in the operation, transport, maintenance, and storage
of equipment.
Thoroughly read and understand
the instructions given in this
manual before operation. Refer to
the “Safety Label” section, read
all instructions noted on them.
Do not allow anyone to operate
this equipment who has not fully
read and comprehended this
manual and who has not been
properly trained in the safe
operation of the equipment.
!
ꢀ Operator should be familiar with
!
Be Aware of
Signal Words
WARNING
all functions of the unit.
Indicates a potentially hazardous
ꢀ Operate implement from the
situation which, if not avoided, could
driver’s seat only.
A Signal word designates a degree or
level of hazard seriousness. The
signal words are:
result in death or serious injury, and
includes hazards that are exposed
when guards are removed. It may also
be used to alert against unsafe
practices.
ꢀ Make sure all guards and shields
are in place and secured before
operating implement.
ꢀ Do not leave tractor
!
DANGER
ꢀ implement unattended with
Indicates an imminently hazardous
situation which, if not avoided, will
result in death or serious injury. This
signal word is limited to the most
extreme situations, typically for
machine components that, for
functional purposes, cannot be
guarded.
!
engine running.
CAUTION
ꢀ Dismounting from a moving
tractor could cause serious injury
or death.
ꢀ Do not allow anyone to stand
between tractor and implement
while backing up to implement.
Indicates a potentially hazardous
situation which, if not avoided, may
result in minor or moderate injury. It
may also be used to alert against
unsafe practices.
ꢀ Keep hands, feet, and clothing
away from power-driven parts.
ꢀ Wear snug fitting clothing to avoid
For Your Protection
Shutdown and Storage
entanglement with moving parts.
ꢀ Watch out for wires, trees, etc.,
when raising implement. Make
sure all persons are clear of
working area.
ꢀ Turning tractor too tight may
cause implement to ride up on
wheels. This could result in injury
or equipment damage.
ꢀ Thoroughly read and understand
the “Safety Label” section, read all
instructions noted on them.
ꢀ Lower machine to ground, put
tractor in park, turn off engine, and
remove the key.
ꢀ Detach and store implements in a
area where children normally do
not play. Secure implement by
using blocks and supports.
ꢀ Do not carry passengers on
OFF
implement at any time.
Parts Manual QR Locator
Dealer QR Locator
The QR (Quick Reference) code on the front
cover and to the left will take you to the
Parts Manual for this equipment. Download
the appropriate App on your smart phone,
open the App, point your phone on the QR
code and take a picture.
The QR code on the left will
link you to available dealers
for Land Pride products.
Refer to Parts Manual
QR Locator on this page for
detailed instructions.
SP2060, SP2072, SP3072 & SP3084 Soil Pulverizers 307-099M
Download from Www.Somanuals.com. All Manuals Search And Download.
7/11/12
1
Important Safety Information
These are common practices that may or may not be applicable to the products described in
this manual.
ꢀ Use the following maximum
Use Safety
Lights and Devices
Transport
Machinery Safely
speed - tow load weight ratios as
a guideline:
ꢀ 20 mph when weight is less than
ꢀ Slow moving tractors, self-
propelled equipment, and towed
implements can create a hazard
when driven on public roads. They
are difficult to see, especially at
night.
ꢀ Comply with state and local laws.
or equal to the weight of tractor.
ꢀ Maximum transport speed for
implement is 20 mph. DO NOT
EXCEED. Never travel at a speed
which does not allow adequate
control of steering and stopping.
Some rough terrain require a
slower speed.
ꢀ Sudden braking can cause a
towed load to swerve and upset.
Reduce speed if towed load is not
equipped with brakes.
ꢀ 10 mph when weight is double
the weight of tractor.
ꢀ IMPORTANT: Do not tow a load
that is more than double the
weight of tractor.
ꢀ Flashing warning lights and turn
signals are recommended
whenever driving on public roads.
ꢀ Allow implement to cool
Keep Riders
Practice Safe
Maintenance
ꢀ Understand procedure before
doing work. Use proper tools and
equipment, refer to Operator’s
Manual for additional information.
completely.
Off Machinery
ꢀ Do not grease or oil implement
ꢀ Riders obstruct the operator’s
view, they could be struck by
foreign objects or thrown from the
machine.
while it is in operation.
ꢀ Inspect all parts. Make sure parts
are in good condition & installed
properly.
ꢀ Never allow children to operate
ꢀ Work in a clean dry area.
ꢀ Remove buildup of grease, oil, or
equipment.
debris.
ꢀ Lower the implement to the
ground, put tractor in park, turn off
engine, and remove key before
performing maintenance.
ꢀ Remove all tools and unused
parts from implement before
operation.
SP2060, SP2072, SP3072 & SP3084 Soil Pulverizers 307-099M
Download from Www.Somanuals.com. All Manuals Search And Download.
7/11/12
2
Important Safety Information
These are common practices that may or may not be applicable to the products described in
this manual.
Avoid High
Wear
Prepare for Emergencies
ꢀ Be prepared if a fire starts.
Pressure Fluids Hazard
Protective Equipment
ꢀ Escaping fluid under pressure can
penetrate the skin causing
serious injury.
ꢀ Avoid the hazard by relieving
pressure before disconnecting
hydraulic lines or performing work
on the system.
ꢀ Make sure all hydraulic fluid
connections are tight and all
hydraulic hoses and lines are in
good condition before applying
pressure to the system.
ꢀ Use a piece of paper or
cardboard, NOT BODY PARTS, to
check for suspected leaks.
ꢀ Wear protective clothing and
equipment appropriate for the job.
Avoid loose fitting clothing.
ꢀ Prolonged exposure to loud noise
can cause hearing impairment or
hearing loss. Wear suitable
hearing protection such as
earmuffs or earplugs.
ꢀ Operating equipment safely
requires the full attention of the
operator. Avoid wearing radio
headphones while operating
machinery.
ꢀ Keep a first aid kit and fire
extinguisher handy.
ꢀ Keep emergency numbers for
doctor, ambulance, hospital, and
fire department near phone.
ꢀ Wear protective gloves and safety
glasses or goggles when working
with hydraulic systems.
ꢀ If an accident occurs, see a
doctor immediately. Any fluid
injected into the skin must be
treated within a few hours or
gangrene may result.
911
SP2060, SP2072, SP3072 & SP3084 Soil Pulverizers 307-099M
Download from Www.Somanuals.com. All Manuals Search And Download.
7/11/12
3
Important Safety Information
4. Refer to this section for proper label placement.
Safety Labels
Your Soil Pulverizer comes equipped with all safety labels in
place. They were designed to help you safely operate your
implement. Read and follow their directions.
To install new labels:
a. Clean the area the label is to be placed.
b. Spray soapy water on the surface where the label is to
be placed.
1. Keep all safety labels clean and legible.
c. Peel backing from label. Press firmly onto the surface.
2. Replace all damaged or missing labels. Order new labels
from your nearest Land Pride dealer. To find your nearest
dealer, visit our dealer locator at landpride.com.
3. Some new equipment installed during repair requires
safety labels to be affixed to the replaced component as
specified by Land Pride. When ordering new components
make sure the correct safety labels are included in the
request.
d. Squeeze out air bubbles with the edge of a credit card
or with a similar type straight edge.
30155
818-719C
General Caution Decal
SP2060, SP2072, SP3072 & SP3084 Soil Pulverizers 307-099M
7/11/12
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Introduction
Land Pride welcomes you to the growing family of new
product owners.
Owner Assistance
The Online Warranty Registration or Warranty
Registration card should be completed by the dealer at
the time of purchase. This information is necessary to
provide you with quality customer service.
This pulverizer has been designed with care and built by
skilled workers using quality materials. Proper assembly,
maintenance, and safe operating practices will help you
get years of satisfactory use from this pulverizer.
The parts on your Soil Pulverizer have been specially
designed by Land Pride and should only be replaced with
genuine Land Pride parts. Contact a Land Pride dealer if
customer service or repair parts are required. Your Land
Pride dealer has trained personnel, repair parts, and
equipment needed to service the implement.
Application
The SP20 and SP30 Soil Pulverizers are designed and
built by Land Pride to loosen, pulverize, and level packed
or encrusted soils in preparation for seeding or laying of
new sod. Both the 20 and 30 Series Pulverizers are
adapted for Category 1 three-point hitch mounting. The
20 series has a minimum 35 hp tractor requirement while
the 30 Series has a minimum 50 hp requirement.
Serial Number
Model No. _____________Serial No. _______________
For quick reference and prompt service, record model
number and serial number in the spaces provided above
correspondences with your Land Pride dealer. Refer to
Figure 1 for location of your serial number plate.
Land Pride Soil Pulverizers come in 60", 72", and 84"
working widths making them well suited for use by
landscapers, rental yards, construction contractors, and
professional turf managers. Applications include golf
courses, housing developments, athletic fields,
nurseries, sod farms, transportation right-of-ways, and
park systems.
Using This Manual
• This Operator’s Manual is designed to help familiarize
you with safety, assembly, operation, adjustments,
troubleshooting, and maintenance. Read this manual
and follow the recommendations to help ensure safe
and efficient operation.
35029
• The information contained within this manual was
current at the time of printing. Some parts may change
slightly to assure you of the best performance.
Serial Number Plate Location
Figure 1
• To order a new Operator’s or Parts Manual contact
your authorized dealer. Manuals can also be
downloaded, free-of-charge from our website at
Further Assistance
Your dealer wants you to be satisfied with your new Soil
Pulverizer. If for any reason you do not understand any
part of this manual or are not satisfied with the service
received, the following actions are suggested:
Terminology
“Right” or “Left” as used in this manual is determined by
facing the direction the machine will operate while in use
unless otherwise stated.
1. Discuss the matter with your dealership service
manager making sure he is aware of any problems
you may have and that he has had the opportunity to
assist you.
Definitions
2. If you are still not satisfied, seek out the owner or
general manager of the dealership, explain the
problem and request assistance.
IMPORTANT: A special point of information related
to the following topic. Land Pride’s intention is this
information must be read & noted before continuing.
3. For further assistance write to:
Land Pride Service Department
1525 East North Street
P.O. Box 5060
NOTE: A special point of information that the
operator should be aware of before continuing.
Salina, Ks. 67402-5060
E-mail address
SP2060, SP2072, SP3072 & SP3084 Soil Pulverizers 307-099M
7/11/12
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1: Assembly & Set-Up
Section 1: Assembly & Set-Up
2. Insert spacer (#4) between upper hitch plates. Install
Tractor Requirements
3/4"-10 x 4" GR5 cap screw (#6), lockwasher (#8),
and hex nut (#7).
Tractor horsepower and hitch category should be within
the range noted below. Tractors outside the horsepower
range must not be used.
3. Insert lower 3-point hitch pins (#9) into clevis lugs.
Secure hitch pins with linch pins (#9).
• SP20 Tractor Horsepower Rating25-35 HP
• SP30 Tractor Horsepower Rating 30-50 HP
• SP20 & SP30 Hitch CategoryCat. I
4. Tighten all Hardware to the proper torque values.
NOTE: Front tractor weights and/or ballast to tires
may be required to offset weight of unit. Consult your
tractor manual for details to install ballast weights.
Dealer Preparations
!
CAUTION!
Never allow anyone under unit while unloading.
Using a lifting device of adequate size to remove crate
from flat bed. Place on a smooth flat work surface and
uncrate unit. This unit is shipped partially assembled. It is
the dealership’s responsibility to finish assembly of the
unit. This section covers the proper way for the Land
Pride dealer to assembly the pulverizer.
Assembly Instructions
Review all safety instructions printed in this manual
before assembling the pulverizer.
30156
NOTE: Do not tighten hardware until assembly is
complete.
Hitch Assembly
Figure 1-1
Torque Requirements
determine correct torque values when tightening
hardware.
SP20 Hitch Assembly
Refer to Figure 1-1:
1. Install upper hitch plates (#1 & #2) inside mounting
bracket plates with 3/4"-10 x 2" GR5 cap
screws (#4), lockwashers (#8), and hex nuts (#6).
2. Insert spacer (#3) between upper hitch plates, install
3/4"-10 x 4" GR5 cap screw (#5), lockwashers (#8),
and hex nut (#6).
3. Make sure 3/4" hex jam nuts (#10) is screwed fully
onto lower hitch pins (#11).
4. Install lower 3-point hitch pins (#11) to the pulverizer
frame with 7/8" lock washers (#9) and hex nuts (#7).
5. Tighten all Hardware to the proper torque values.
Hitch Assembly
Refer to Figure 1-2:
30157
1. Install upper hitch plates (#2 & #3) inside mounting
brackets with 3/4"-10 x 2" GR5 cap screws (#5),
lockwashers (#8), and hex nuts (#7).
Hitch Assembly
Figure 1-2
SP2060, SP2072, SP3072 & SP3084 Soil Pulverizers 307-099M
7/11/12
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Operating
Section 2: Operating
• Never carry passengers or use the Soil Pulverizer as a
Operator’s Responsibilities
wagon to carry things.
Hazard control and accident prevention are dependent
upon the awareness, concern, prudence and proper
training involved in the operation, transport, storage, and
maintenance of the Soil Pulverizer. Therefore, it is
absolutely essential that no one operates the Soil
Pulverizer without first having read, fully understood and
become totally familiar with the Operator’s Manual. Make
sure the operator has completed the Operating Checklist
below.
• Never use the Soil Pulverizer to pull or tow other
equipment or objects.
• Make sure all safety labels are in their proper location
and in good condition before operation.
• Never work under the Soil Pulverizer without properly
blocking pulverizer up.
• Before working the soil contact your local utility
services, so that they may mark location of any under
ground utility services in the area. Be sure to ask how
close you can work to the marks or flags they
positioned.
Operating Checklist
Page No.
✔
Check
• Do not alter the Soil Pulverizer in a way which will
adversely affect its performance or reliability or use the
Soil Pulverizer for a purpose for which it was not
designed.
Read and follow all Safety Rules carefully.
Make sure all guards and shields are in place.
Read and follow Hook-up & preparation instructions.
Be sure all pins have been installed and are secured.
Tractor Hook-Up
Refer to Figure 2-1:
Read and follow all operating instructions. Make sure
Pulverizer.Refer to “Section 2: Operating”.
!
DANGER!
Tractor hook-up to equipment is dangerous and can result in
serious injury or death. Do not allow anyone to stand between
the Soil Pulverizer and tractor during hook-up operations. Do
not operate hydraulic 3-point lift controls while someone is
directly behind the tractor or near the Soil Pulverizer.
Read and make all required adjustments. Be sure all
pins have been installed and are secured.
Read and follow all Maintenance Instructions.
A 3-Point Category I hitch is required.
Make sure their are no hydraulic leaks on the unit.
1. Slowly back tractor up to the Soil Pulverizer and use
tractor’s 3-point hydraulic control to align the lower
hitch link holes with the clevis lug holes on the Soil
Pulverizer.
Check Soil Pulverizer initially and periodically for loose
bolts and pins. Refer to “Torque Values Chart”.
2. Engage tractor park brake, shut tractor engine off
and remove key before dismounting from tractor.
!
WARNING!
It is the operator’s responsibility not to allow anyone near the
Soil Pulverizer during its operation.
3. With tractor’s lower hitch arms aligned and
positioned in the clevises, attach lower arms to the
clevises with hitch pins and secure with linchpins.
!
CAUTION!
Be sure that you are not working over any underground
wiring, pipes, or other obstructions. If there is any doubt, call
your public service agency.
!
CAUTION!
Always keep your feet and legs out from under the shanks
when adjusting height of shanks. It is possible the shanks
could slip and fall causing injury to your feet and/or legs.
• Follow all directions on the safety labels.
• Do not allow anyone to operate this Soil Pulverizer who
has not been properly trained in its safe operation.
• Do not let anyone under the age of 16 operate the Soil
15691
Pulverizer.
Tractor Hook-Up
Figure 2-1
• Use the Soil Pulverizer for its intended purpose only.
SP2060, SP2072, SP3072 & SP3084 Soil Pulverizers 307-099M
7/11/12
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Operating
4. Connect top center link to the upper hitch with top
link pin (supplied by customer).
General Operating Instructions
5. Return to the tractor and slowly operate the tractor's
3-Point hydraulic control up and down to check for
clearance between the tires, frame, drawbar etc.
Move or remove drawbar if it interferes with the Soil
Pulverizer.
!
DANGER!
Operator to wear Seat Belt at all times while operating
implement.
6. Manually adjust one of the two lower lift arms up or
down to level the Soil Pulverizer from left to right.
!
WARNING!
Speeds in excess of 5 MPH can damage frame & or shanks
7. Manually adjust the length of the top-link to level the
Soil Pulverizer from front to rear.
IMPORTANT: Do Not turn tractor with pulverizer
shanks in the ground. Damage to shanks will occur.
Transporting
Before putting your Land Pride Pulverizer into service
you must thoroughly review the Operator’s Manual. Once
you have read the Operator’s Manual and properly
mounted the pulverizer on your tractor, you should be
ready to head for the work site. You should have already
removed any sizeable sticks, rocks, or extraneous debris
from this area. Do not attempt to rip up concrete, black
top, asphalt, or large rocks.
!
CAUTION!
When traveling on public roads at night or during the day, use
accessory lights and devices for adequate warning to
operators of other vehicles. Comply with all federal, state, and
local laws.
1. Be sure to reduce tractor ground speed when
turning; and leave enough clearance so the Soil
Pulverizer does not contact obstacles such as
buildings, trees, or fences.
With tractor stopped, lower 3-point of tractor down until
all weight is off the tractor. Pull ahead slowly to get the
shanks to start digging. Scarifying and pulverizing action
will commence as soon as the rear roller touches the
ground and begins to roll. Increase ground speed once
shanks and roller have entered the ground. Do not
exceed 5 MPH and make straight passes only. When you
reach the end of a pass, raise tractor’s 3-point up before
turning. Trying to turn with unit in the ground will damage
the scarifier shanks and can damage the pulverizer
roller.
2. Select a safe ground travel speed when transporting
from one area to another.
3. When traveling on roadways, transport in such a way
that faster moving vehicles may pass you safely.
4. When traveling over rough or hilly terrain, shift tractor
to a lower gear.
Adding Weight
If ground conditions are extremely hard and the scarifier
shanks are not achieving adequate penetration, you may
need to add additional weight to the top frame.
Up to 400 lbs can be added to this area.
Up to 400 lbs of weight may be applied by installing
bricks or blocks in frame for additional weight if required
by ground conditions.
If the pulverizing roller is bouncing and not staying in
uniform contact with the ground, the down pressure of
the roller can be adjusted by the spring tensioners
located at both ends of the pulverizer.
If you are getting a build-up on the rear roller, pulverizing
operations should be discontinued until the ground is dry
enough to work. If the ground needs more cultivation
than can be accomplished in one pass, continue to make
additional passes until the desired finish is achieved.
Owners of the Model 30 Series Land Pride Pulverizers
can attach an additional optional rear mounted pulverizer
roller to achieve a more professional finish in less time.
Once you are finished using your pulverizer, park it on a
dry and level surface, clean it, and make it ready for the
next use. With a little practice you will be able to achieve
professional results from your Land Pride Pulverizer.
SP2060, SP2072, SP3072 & SP3084 Soil Pulverizers 307-099M
7/11/12
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3: Adjustments
Section 3: Adjustments
Shanks
Refer to Figure 3-1:
Shanks can be removed & installed upside down to give
dual life to shanks.
5. Remove cotter pin (#1) from one end of pulverizer.
6. Pull rod (#2) from channel.
7. Flip shanks (#3) over and reinstall rod (#2).
8. Reinstall cotter pin (#1).
15681
Shanks
Figure 3-1
SP2060, SP2072, SP3072 & SP3084 Soil Pulverizers 307-099M
7/11/12
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Maintenance & Lubrication
Section 4: Maintenance & Lubrication
thoroughly with a garden hose. A coating of oil may be
applied to the wear areas to minimize oxidation.
Maintenance
Proper servicing and adjustment is the key to the long life
of any implement. With careful inspection and routine
maintenance, you can avoid costly down time and repair.
2. Check shanks a for wear and replace if necessary.
See
3. Repaint parts where paint is worn or scratched to
prevent rust. Ask your Land Pride dealer for aerosol
touch-up paint. They are also available in touch-up
bottles with brush, quarts, and gallon sizes by adding
TU, QT, or GL to the end of the aerosol part number.
Check all bolts after using unit for several hours to be sure
they are tight. Replace any worn, damaged, or illegible
safety labels by obtaining new labels from your Land
Pride Dealer.
The parts on your Soil Pulverizer have been specially
designed and should only be replaced with genuine Land
Pride parts. Do not alter the pulverizer in a way which will
adversely affects its performance.
Land Pride Aerosol Touch-up Paint
Part No.
Part Description
821-011C
821-002C
821-066C
PAINT LP BEIGE AEROSOL SPRAY CAN
PAINT LP BLACK AEROSOL SPRAY CAN
PAINT ORANGE AEROSOL SPRAY CAN
Long Term Storage
Clean, inspect, service, and make necessary repairs to
the pulverizer when parking it for long periods and when
parking it at the end of a working season. This will help
ensure the pulverizer is ready for field use the next time
you hook-up to it.
4. Replace all damaged or missing decals.
5. Lubricate as noted below.
6. Store pulverizer on a level surface in a clean, dry
place. Inside storage will reduce maintenance and
make for a longer pulverizer life.
1. Clean off any dirt and grease that may have
accumulated on the pulverizer and moving parts.
Scrape off compacted dirt and then wash surface
Lubrication Points
Lubrication
Legend
Multi-purpose
spray lube
Multi-purpose
grease lube
Multi-purpose
oil lube
Intervals in hours
at which lubrication
is required
50
10
Hours
Rear Roller Bearing
Both ends
Type of Lubrication: Multi-purpose grease lube
Quantity = As Required
30155
10
Hours
SP30 Double Rear Roller Bearing
Both ends
Type of Lubrication: Multi-purpose grease lube
Quantity = As Required
17841
SP2060, SP2072, SP3072 & SP3084 Soil Pulverizers 307-099M
Download from Www.Somanuals.com. All Manuals Search And Download.
7/11/12
10
Section 5: Specifications & Capacities
Section 5: Specifications & Capacities
SP2060, SP2072, SP3072 & SP3084
SP2060
SP2072
72"
SP3072
72"
SP3084
84"
Width
60"
Weight (With Single
Roller- lbs.)
491
561
671
721
Max Engine Hp.
35 Hp.
21
35 Hp.
25
50 Hp.
25
50 Hp
29
Number Of Shanks
Number Of Spikes -
Single Roller
86
103
103
116
Number Of Spikes -
Double Roller
N/A
N/A
206
232
Height
36 1/2"
24"
36 1/2"
27 1/4"
Front To Back Length
Single Roller
Front To Back Length
Double Roller
N/A
35 1/4"
Shank Spacing
2 13/16"
2 13/16"
Spiked Roller Tube
Diameter
5 9/16" O.D
6 5/8" O.D. (Optional Second Roller 5 9/16")
H-Beam
10"
12"
A-Frame
3/8" Plate
Springs-Front Roller
Springs - Rear Roller
Spike Material
32 lbs./inch
32 lbs./inch
15 lbs./inch
N\A
N/A
3/8" x 1 1/4" Steel, Replaceable Heat
Treated Sleeves
3/8" x 1 1/4" Steel, Replaceable Heat Treated
Sleeves
Hitch
Cat. 1
Cat. 1
SP2060 = 65 1/4"
SP2072 & SP3072 = 77 1/4"
SP3084 = 89 1/4"
SP20 = 25 1/2"
SP30 = 28 1/4"
36 1/4"
17"
35031
SP2060, SP2072, SP3072 & SP3084 Soil Pulverizers 307-099M
7/11/12
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6: Features & Benefits
Section 6: Features & Benefits
SP20 & SP30 Series Soil Pulverizers
Features
Benefits
20 Series: 60", 72"; 30 Series: 72", 84"
Working widths
HP Range
20 Series: 20-35 HP; 30 Series: 30-50 HP
Replaceable heat-treated
sleeves
Heat-treated replaceable sleeves on roller protect spike. Easily replace the sleeve when
worn vs. replacing entire spike.
3/8" Steel spikes welded
to the roller’s surface
Spikes are welded to the roller’s surface rather than to a hole. Damaged spikes can be cut
off and replaced.
Self-aligning bearings with
double lip seals on rear roller
Self-aligning bearings conform to the roller and shafts.
1" Diameter shaft in roller
Heavy shaft can handle the shock loads from the roller.
Better pulverization, more spikes than most competitors
Roller has high number
of steel spikes
H Beam
20 Series: H Beam-10"; 30 Series: H Beam-12"
10 1/2" x 2" x 2 " Scarifier teeth Scarifier teeth are heat-treated for long life and can be reversed when one side wears
down.
Warranty
One year parts and labor
Fits Land Pride Quick-Hitch
Cat. 1 3-point fits Land Pride Quick-Hitch for easy on-off with one person.
SP2060, SP2072, SP3072 & SP3084 Soil Pulverizers 307-099M
Download from Www.Somanuals.com. All Manuals Search And Download.
7/11/12
12
Section 7: Troubleshooting
Section 7: Troubleshooting
Problem
Solution
Adjust spring tension
Roller or Rollers not staying on ground,
Bouncing.
Lift shanks out of ground while turning
Shanks bending sideways.
Bending frame and or shanks
Shanks won’t go into ground
Do not rip up concrete, asphalt, or blacktop. Do not hit solid objects.
3-point has not been lowered
weight may need to be added to frame (refer to adding weight in operating
instructions).
Do not rip up concrete, asphalt, or blacktop
SP2060, SP2072, SP3072 & SP3084 Soil Pulverizers 307-099M
7/11/12
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 8: Torque Values Chart
Section 8: Torque Values Chart
Torque Values Chart for Common Bolt Sizes
Bolt Head Identification
Bolt Head Identification
8.8
10.9
5.8
Bolt Size
(Inches)
Bolt Size
(Metric)
Class 5.8
Class 8.8
Class 10.9
Grade 2
2
Grade 5
3
Grade 8
1
in-tpi
1/4" - 20
1/4" - 28
5/16" - 18
5/16" - 24
3/8" - 16
3/8" - 24
7/16" - 14
7/16" - 20
1/2" - 13
1/2" - 20
9/16" - 12
9/16" - 18
5/8" - 11
5/8" - 18
3/4" - 10
3/4" - 16
7/8" - 9
N·m ft-lb
N·m ft-lb N·m ft-lb
mm x pitch N·m ft-lb N·m ft-lb N·m ft-lb
7.4
5.6
11
8
16
12
M 5 X 0.8
4
3
6
5
9
7
8.5
6
11
13
10
18
14
M 6 X 1
7
5
11
8
15
11
15
24
17
33
25
M 8 X 1.25
M 8 X 1
17
12
26
19
36
27
17
13
26
19
37
27
18
13
28
21
39
29
27
20
42
31
59
44
M10 X 1.5
M10 X 0.75
M12 X 1.75
M12 X 1.5
M12 X 1
33
24
52
39
72
53
31
22
47
35
67
49
39
29
61
45
85
62
43
32
67
49
95
70
58
42
91
67
125
130
145
200
l215
315
335
405
485
610
900
93
49
36
75
55
105
145
165
210
235
285
325
510
570
820
905
78
60
44
95
70
97
66
49
105
115
150
165
205
230
360
405
585
640
875
955
76
105
120
155
170
210
240
375
420
605
670
910
995
90
66
105
145
155
225
240
310
350
440
650
760
830
77
105
150
160
230
245
300
355
450
665
780
845
75
55
85
M14 X 2
92
68
105
115
165
180
230
260
325
480
95
70
110
120
150
170
265
295
430
475
M14 X 1.5
M16 X 2
99
73
105
130
150
235
260
225
250
340
370
480
540
680
750
890
1010
1180
1330
79
145
155
195
220
280
310
480
525
960
1060
105
115
145
165
205
230
355
390
97
M16 X 1.5
M18 X 2.5
M18 X 1.5
M20 X 2.5
M20 X 1.5
M24 X 3
110
170
190
165
185
250
275
7/8" - 14
1" - 8
560 1050
610 1150
645 1230
705 1350
M24 X 2
1" - 12
M30 X 3.5
M30 X 2
705 1510 1120 2100 1550
785 1680 1240 2320 1710
1-1/8" - 7
1-1/8" - 12
1-1/4" - 7
1-1/4" - 12
1-3/8" - 6
1-3/8" - 12
1-1/2" - 6
1-1/2" - 12
355 1080
395 1210
795 1750 1290
890 1960 1440
M36 X 3.5
1730 1270 2650 1950 3660 2700
1880 1380 2960 2190 4100 3220
500 1520 1120 2460 1820
555 1680 1240 2730 2010
655 1990 1470 3230 2380
745 2270 1670 3680 2710
870 2640 1950 4290 3160
980 2970 2190 4820 3560
M36 X 2
1
in-tpi = nominal thread diameter in inches-threads per inch
N· m = newton-meters
2
3
4
ft-lb= foot pounds
mm x pitch = nominal thread diameter in millimeters x thread
pitch
Torque tolerance + 0%, -15% of torquing values. Unless otherwise specified use torque values listed above.
SP2060, SP2072, SP3072 & SP3084 Soil Pulverizers 307-099M
7/11/12
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 9: Warranty
Section 9: Warranty
Warranty
Land Pride warrants to the original purchaser that this Land Pride product will
be free from defects in material and workmanship beginning on the date of
purchase by the end user according to the following schedule when used as
intended and under normal service and conditions for personal use.
Overall Unit: One year Parts and Labor
Spikes and roller studs: Considered wear items
This Warranty is limited to the replacement of any defective part by Land
Pride and the installation by the dealer of any such replacement part, and does
not cover common wear items. Land Pride reserves the right to inspect any
equipment or parts which are claimed to have been defective in material or
workmanship.
This Warranty does not apply to any part or product which in Land Pride’s
judgment shall have been misused or damaged by accident or lack of normal
maintenance or care, or which has been repaired or altered in a way which
adversely affects its performance or reliability, or which has been used for a
purpose for which the product is not designed. Misuse also specifically includes
failure to properly maintain oil levels, grease points, and driveline shafts.
Claims under this Warranty should be made to the dealer which originally sold
the product and all warranty adjustments must be made through an authorized
Land Pride dealer. Land Pride reserves the right to make changes in materials
or design of the product at any time without notice.
This Warranty shall not be interpreted to render Land Pride liable for damages
of any kind, direct, consequential, or contingent to property. Furthermore, Land
Pride shall not be liable for damages resulting from any cause beyond its
reasonable control. This Warranty does not extend to loss of crops, any expense
or loss for labor, supplies, rental machinery or for any other reason.
No other warranty of any kind whatsoever, express or implied, is made
with respect to this sale; and all implied warranties of merchantability and
fitness for a particular purpose which exceed the obligations set forth in
this written warranty are hereby disclaimed and excluded from this sale.
This Warranty is not valid unless registered with Land Pride within 30 days
from the date of purchase by the end user.
Model Number ____________________
Serial Number ____________________
SP2060, SP2072, SP3072 & SP3084 Soil Pulverizers 307-099M
Download from Www.Somanuals.com. All Manuals Search And Download.
7/11/12
15
Corporate Office: P.O. Box 5060
Salina, Kansas 67402-5060 USA
Download from Www.Somanuals.com. All Manuals Search And Download.
|