57” ROUGH CUT
MR55K
MR55B
OWNER’S MANUAL
With Assembly Instructions
For Models: MR55T, MR55B-17.5HP, MR55B-22-23HP & MR55K
KUNZ ENGINEERING, INC. / MENDOTA, IL 61342 / PH (815) 539-6954
1/09
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INFORMATION
WARNING: Do not allow anyone to operate this equipment who has not fully read and
comprehended the safety manual and who has not been properly trained in the safe
operation of the equipment.
WARNING: Operator should be familiar with all functions of the unit.
DANGER: Keep hands, feet, hair and clothing away from moving parts.
WARNING: Remove all objects from the work area that might be picked up and thrown by
the blades.
WARNING: Do not mow when children and others are around.
WARNING: Keep all safety shields and deflectors in place during operation.
WARNING: Shut off the engine and allow the mower blades to come to a complete stop
before making any adjustments to the mower.
WARNING: Shut off engine before disconnecting the mower from the tow vehicle or
attempting to move the mower by hand.
WARNING: Never carry children or passengers.
WARNING: Do not allow children to operate this machine.
This entire manual is filled with important safety information. Please read it
carefully.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY SIGNS AND LOCATIONS
275003 – Danger
275007 – Warning
Decal, Cut Hand & Foot
Decal, Belt Sheild
275002 – Warning
Decal, General
Serial # and Model #
Decal
Clean or Replace Any Safety Signs That Are not Readable or Damaged
Replacement decals can be purchased from your local dealer or
Kunz Engineering Inc.
Mendota, IL 61342
(815) 539-6954
3
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTIONS
Read the complete assembly instructions before starting the assembly.
You should have:
- one mower deck assembly
- two carrier arm assemblies
- two rear tire assemblies
- one ATV tongue assembly
A. ASSEMBLY OF MOWER WHEELS
1. Set the mower deck assembly on wood blocks so that it is suspended off the ground.
Note: The operator controls are on the front of the deck. (Left and right are determined by
looking in the direction of travel or by standing at the rear of the deck assembly looking
forward.)
2. Install the rear tire assemblies on the carrier arm assemblies. Remove the hex nut and lock
washer from the rear tire assembly and install the 5/8”x7-1/2” tire axle bolt through the hole in
the carrier arm assembly. See figure 1. Secure assembly with the lock washer and hex nut
provided on the rear tire assembly. The rear tires should be offset to the outside of the deck
assembly on both sides. See figure 2.
3. Install the two carrier arm assemblies in the pivot arms, which are located on the mower deck
assembly. Place the assembly so that the castered tires are on the front and the fixed tires are
on the back. See figure 2. Secure with 1/2" x 3-1/2" hex head bolts and lock nuts provided on
the pivot arms. Mount the height adjust screw on the deck assembly in the hole provided.
Secure with the 1/2”x1” hex head bolt and lock nut provided on the height adjust screw.
Note: Tighten 1/2” x 3-1/2” and 1/2” x 1” hex head bolts until just snug. This area needs to
pivot when adjusting the height. Under tightening can result in excessive wear and
flexing. Over tightening will make adjusting the cutting height very difficult.
B. INSTALLATION OF TONGUE ASSEMBLY
1. The tongue can be installed either on the left or right caster assembly depending on how the
tow-behind mower will be towed. See figure 2. Secure the hitch pivot on the chosen caster
assembly with the 1/2” x 3-1/2” hex head bolt, lock washer, and nut provided.
2. Install the tongue into the hitch pivot and secure by placing the provided 5/16” wire lock pins on
each side of the hitch pivot.
Note: To help prevent any unwanted pin removal caused by oncoming debris install the 5/16”
wire lock pins with the wire lock section back from the direction of travel. See Figure 3.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Carrier Arm
Assembly
Rear Tire
Bolt
Hex Nut and
Lock Washer
Cup Washer
Flat Washer
Figure 1: Rear Tire Assembly Installation
Hitch Pivot – Attach to
Either Left or Right
Carrier Arm Assy.
Tongue
Height Adjust
Screw
Front (Rubber
Flap Side)
Rear Tire Assy.
(Attach on outside for
both left and right sides)
Carrier Arm
Assy.
Pivot Arm
Offset Position
Direct Behind Position
Figure 2: Assembly of Carrier Arm Assy., Hitch Pivot, and Tongue
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Direction of Travel
Screw Pin Shackle
Clevis
Shift Tongue Left or Right
Between Holes
Tongue
5/16” Wire
Lock Pins
Wire Lock Section of
Wire Lock Pin
(Placed Back From
Direction of Travel)
Figure 3: ATV Tongue Assembly
OPERATIONS AND ADJUSTMENTS
This safety alert symbol is used to indicate safety instructions. Follow
these instructions to avoid personal injury and/or property damage.
Read and follow all instructions in this manual and the attached engine
manual.
WARNING: Do not allow anyone to operate this equipment who has not fully read and
comprehended the safety manual and who has not been properly trained in the safe
operation of the equipment.
WARNING: Operator should be familiar with all functions of the unit.
A. TONGUE CONFIGURATIONS AND ADJUSTMENTS
WARNING: Shut off the engine and allow the mower blades to come to a complete stop
before adjusting the tongue.
The hitching system is designed so that the rough cut mower can be pulled directly behind a tow
vehicle or offset to the left or right. See Figure 4.
Note: When pulling the mower directly behind, the hitch pivot should be fastened on the right
carrier arm for maximum maneuverability. See Figure 2. When pulling the mower in
the offset position the hitch pivot can be fastened on either the right or left carrier arm.
See Figure 2.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
The tongue is equipped with a screw pin shackle clevis to provide movement in all directions on
rough uneven ground. To prevent loss of the screw pin due to vibration or debris, place the screw
pin through the tow vehicle hitch and clevis and turn the screw pin until snug.
The tongue is designed to adjust from left to right within the hitch pivot. This allows the mowers
position to be varied behind the tow vehicle. This is accomplished by pulling the 5/16” wire lock
pins out and choosing two other hole locations on the tongue. See Figure 3.
Directly Behind
Offset
Figure 4: Rough Cut Tow Behind Towing Suggestions
B. ADJUSTING CUTTING HEIGHT
WARNING: Shut off the engine and allow the mower blades to come to a complete stop
before adjusting the cutting height.
Adjustment Crank: Roughly 6
turns equals 1.0”
Mower Blade
Lower Edge of
Deck
Measure This Distance
and Add 1-5/16” to get
Cutting Height
Cutting Height
1-5/16”
Smooth Surface
Figure 5: Adjusting Rough Cut Mower Cutting Height
7
Download from Www.Somanuals.com. All Manuals Search And Download.
The cutting height can be adjusted in a range from 2.0" to 8.0". This is accomplished by turning
the height adjust cranks on both sides of the mower. See Figure 5. Turn the cranks clockwise to
raise the mower cutting height and counter-clockwise to lower the mower cutting height.
DANGER: Shut off tow vehicle engine and allow mower blades to stop completely before
attempting to measure the cutting height.
Adjust the mower as follows:
1. Pull the mower on to a smooth, level surface.
2. Adjust the mower evenly from side to side by measuring to the ground from the lower edge of
the mower deck. The desired height will be the distance from the ground to the outside lower
edge of the mower deck plus 1-5/16”. The mower blade cutting edge is 1-5/16” above the
outside lower edge of the mower deck.
Note: If the height adjust cranks do not turn easily, the pivot bolts holding the carrier arm
assemblies and height adjust screw may be too tight. Loosen the pivot bolts slightly to
allow easier pivoting. Care should be taken not to loosen too much or excess wear and
flexing may occur. Greasing the threads may also allow greater ease in adjustment.
Note: After leveling mower deck, quick field adjustment can be completed by counting crank
turns. Roughly 6 turns will equal 1” of vertical movement.
The adjustment crank may unturn due to vibration. This will allow the mower’s cutting height to
change. The crank can be secured by folding it down between the adjustment nut tube and the
upper pivot support. See Figure 6.
Adjustment Crank
Adjustment Nut Tube
Carrier Arm
Upper Pivot Support
Figure 6: Securing Crank While Not In Use
8
Download from Www.Somanuals.com. All Manuals Search And Download.
C. STARTING ENGINE
WARNING: Set parking brake on tow vehicle.
Attach mower tongue to tow vehicle.
WARNING: Do not start rough cut mower unless it is attached to the tow vehicle.
Turn on fuel shut off valve which is located on the underside of the gas tank.
Set the choke to the desired position.
Set the throttle at approximately half throttle.
Start engine and allow engine to warm up.
Set engine speed at about half throttle and engage mower blades clutch handle. (The clutch
handle is located at the front of the mower under the engine.)
Note: Some belt squealing may occur on engagement. This is normal for a manual clutch
engagement design.
CAUTION: If the mower’s engine dies while in use, remove the rough cut mower from the
uncut area before attempting to engage the clutch. Inspect the blades for any obstructions
that may prevent blade engagement. Failure to follow these instructions may result in
premature clutch and belt failure or a fire.
Adjust engine speed to full throttle.
D. SHUTTING OFF ROUGH CUT MOWER
WARNING: Shift to neutral and set the parking brake before dismounting the tow vehicle.
Slow the engine speed down and disengage the clutch handle.
Allow engine to cool down for a short time before moving the ignition switch to the off position.
Turn off fuel shut off valve which is located on the underside of the gas tank.
E. MOWER OPERATION
DANGER: Keep hands, feet, hair and clothing away from moving parts.
CAUTION: Clean or replace any safety signs that are not readable or damaged.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING: Remove all objects from the work area that might be picked up and thrown by
the blades.
WARNING: Do not mow when children and others are around.
WARNING: Do not fill fuel tank while engine is running or hot.
WARNING: Keep all safety shields and deflectors in place during operation.
CAUTION: Remove grass build up from under safety shields before each use. Do not
remove safety shields while engine is running. Dry grass build up around belts and
sheaves can cause fires.
WARNING: Shut off engine before disconnecting the mower from the tow vehicle or
attempting to move the wing mower by hand.
WARNING: Never carry children or passengers.
WARNING: Do not allow children to operate this machine.
CAUTION: Slow down and watch the ends of the mower when making turns so objects
are not struck and/or run over.
WARNING: Look down, to the sides, and behind before and while backing to avoid
backing over something or someone. Care should also be taken while backing so that the
wing mower or mowers do not jackknife and damage hitches.
WARNING: Stop the mower blades on the mower if the tow vehicle becomes stuck or
stops going forward because of loss of traction. Shut off the engine on the mower before
attempting to push or pull the tow vehicle.
Listen to the rough cut mower engine while mowing. The engine should run free and not work too
hard. Working the engine too hard will cause overheating and premature failure.
CAUTION: If the mower’s engine dies while in use, remove the rough cut mower from the
uncut area before attempting to engage the clutch. Inspect the blades for any obstructions
that may prevent blade engagement. Failure to follow these instructions may result in
premature belt failure or a fire.
Do not allow material to build up on the air inlet to the engine cooling system. Special care should
be taken to make sure the engine is getting enough inlet air. Do not allow the engine cooling fins
under the shroud to be blocked. If air flow over the engine is restricted, the engine could
overheat.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
F. DRIVE BELT REMOVAL AND TENSION – Refer to Figure 7
WARNING: Shut off engine and allow mower blades to stop turning before making any
adjustments or repairs.
Remove the safety shields.
Loosen the nuts on the spring-loaded idler; adjust bolt until the belt can be slipped off the idler and
drive sheaves.
Slip the belt down under the drive sheave and off the blade spindle sheaves.
Install the new belt and then adjust the tension as follows: See Figure 7. Take special care to
make sure that the belt is placed between the brake stud and the idler pulley.
With the clutch engaged, adjust the nuts on the spring-loaded idler adjuster bolt until the length of
the spring is between 2” and 2-1/8” (For models with 3” long spring) or 2-3/8” and 2-1/2” (For
models with 4-1/2” long spring). This is the initial belt break in spring length. When the belt is
broken in after several hours of mowing, the running spring length should be between 2-1/4” and
2-3/8” (For models with 3” long spring) or 2-5/8” and 3-1/8” (For models with 4-1/2” long spring).
For maximum belt life, periodic checks every 3-4 hours should be done to make sure the spring
length has not exceeded the recommended running length.
Note: Failure to periodically adjust the belt tension will result in severe belt wear and
premature belt failure.
This model comes with a belt brake, which is a safety feature that stops the blades from turning
after the clutch is disengaged. The only time the brake should be in contact with the belt is when
the clutch is disengaged.
CAUTION: The brake stud must be adjusted. If the brake stud is not adjusted correctly,
the blades will still spin even though the clutch may be in the disengaged position. Always
shut mower engine off before servicing.
Periodic brake stud inspections should be performed every 10 hours. In more severe cutting
conditions, more frequent inspections may be necessary. There are two parts to inspecting the
brake stud. Those two inspections are the disengaged spring length and brake stud clearance.
Note: It is quicker to perform the disengaged spring length and brake stud clearance
inspections if done simultaneously.
Disengaged Spring Length:
This inspection must be performed to make sure that there is proper braking force to prevent the
blades from spinning when the clutch is in the disengaged position. With the clutch in the
disengaged position measure the spring length. The spring must be between 2-5/8” and 2-7/8”
(For models with 3” long spring) and between 3-1/4” and 4” (For models with 4-1/2” long spring) to
11
Download from Www.Somanuals.com. All Manuals Search And Download.
provide the appropriate braking force. If the spring length is to long it will be necessary to adjust
the brake stud closer to the belt. If the spring length is to short it will be necessary to adjust the
brake stud further away from the belt. To make brake stud adjustments loosen the bolt on the top
of the brake stud and slide the brake stud in the slot. When the proper disengaged spring length
is achieved, tighten the bolt on the top of the brake stud. For this procedure do not adjust the
spring length. The spring length should only be changed when adjusting the belt tension.
Brake Stud Clearance:
This inspection is necessary to prevent over-braking. With the clutch engaged, check to make
sure that there is at least 1/2” of clearance between the brake stud and the belt. If the clearance
is less than 1/2” then it will be necessary to adjust the brake stud away from the belt. Keep in
mind that the disengaged spring length must stay between 2-5/8” and 2-7/8” (For models with 3”
long spring) and between 3-1/4” and 4” (For models with 4-1/2” long spring).
CAUTION: If brake stud is not set in correct position, under-braking or over-braking may
occur. If over-braking occurs, premature belt failure or a possible fire could occur due to
excessive friction and overheating.
Clutch Engagement
Clutch Arm
Front
See Below For
Recommended Spring
Lengths
Engine
No Less Than 1/2” Clearance With
Clutch Engaged
Brake Stud
0” With Clutch Disengaged
Initial Spring Length: 2” – 2-1/16” (Models with 3” long spring), 2-3/8” – 2-1/2” (Models with 4-1/2” long spring)
Running Spring Length: 2-3/4” – 3-1/4” (Models with 3” long spring), 2-5/8” – 3-1/8” (Models with 4-1/2” long spring)
Disengaged Spring Length: 2-5/8” – 2-7/8” (Models with 3” long spring), 3-1/4” – 4” (Models with 4-1/2” long spring)
Figure 7: Belt Pattern, Spring Adjustment, and Brake Adjustment
12
Download from Www.Somanuals.com. All Manuals Search And Download.
G. MOWER BLADE REMOVAL, BALANCING & INSTALLATION
CAUTION: Sharp blades can cause bodily injury if not handled properly.
When removing the blade, it is recommended that a block of wood be placed between the blade
and the underside of the mower deck. This will allow the removal of the blade without the need to
hold the blade by hand.
CAUTION: Always balance the mower blades each time they are sharpened.
Out of balance mower blades cause excess vibrations which lead to premature bearing failures,
bolts coming loose, and overall deterioration of the wing mowers.
CAUTION: Always properly tighten the blade bolts to the specified torque. Failure to do so
can lead to unwanted loosening of the blade and damage to the blade holding saddle.
The Models MR55K, MR55B and MR55T use the Kunz Engineering Part # (202141) blade bolt.
This particular hex head bolt is a 3/4” – 16NF x 1-1/4” long, grade 5 and it’s proper torque is 300
ft-lbs.
To ease in the blade installation process, use the same block of wood and method used during
the removal of the blades.
H. LUBRICATION
There are five lubrication points on the rough cut mower -- one spring-loaded idler pivot, two
caster wheel pivots, and two blade spindles. Lubricate at approximately 10 hr. intervals or more
often as required in dusty conditions. Lubricate the blade spindles 2-5 pumps every 50 hours.
(The bearings have trash guard seals to hold the seals in place during lubrication.) Lubricate with
a high grade of pressure gun grease.
Note: Do not over grease blade spindles. Blade spindles are initially greased at the factory.
Greasing before 50 hrs. may cause bearing seal damage which will result in premature
bearing failure.
I. STORAGE
Turn off fuel shut off valve which is located on the underside of the gas tank. If the mower is
stored outside, the engine should be covered to prevent water from getting inside the engine
during heavy rainstorms. See the Engine Manual for additional information.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
ACREASE ROUGH CUT MOWER SPECIFICATIONS
Model
Model
Model
Model
MR55T
MR55B-17.5HP
MR55B-22-23HP
MR55K
ENGINE:
Engine Make
Tecumseh
Briggs & Stratton
Briggs & Stratton
Kohler
Engine Model
Enduro OHV 170-EXE
Intek AVS OHV
Intek OHV
Command OHV
Cylinders
1
1
2
2
Cycles
4
4
4
4
Crankshaft
Vertical
Vertical
Vertical
Vertical
Engine HP
17
17.5
22-23
20
Bore
3.56”
3.57"
2.97"
3.03"
Stroke
3.00”
29.9 cubic inches
1.94 U.S. qt
1.0”
3.06"
30.6 cubic inches
1.5 U.S. qt
1.0"
2.89"
44.0 cubic inches
2 U.S. qt
2.64"
38.1 cubic inches
2 U.S. qt
Displacement
Oil Capacity
Crankshaft Dia.
Key Slot
1.0"
1.0"
1/4”
1/4"
1/4"
1/4"
Crankshaft Length
Threaded Hole in End of Crankshaft
Engine Mounting Bolts
Starter
3.15”
3.15"
3.15"
3.15"
7/16-20
7/16-20
7/16-20
7/16-20
3/8-16x1.00 Thread Rolling
Electric
5/16-18x1.50 Through Bolt
Electric
5/16-18x1.50 Through Bolt
Electric
5/16-18x1.50 Through Bolt
Electric
Choke
Manual
Manual
Manual
Manual
MOWER:
Fuel Tank
3-3/4 Gal.
57”
3-3/4 Gal.
57"
3-3/4 Gal.
57"
3-3/4 Gal.
57"
Effective Cutting Width
Deck Construction
Cutting Height
10 ga. Welded steel
2” to 8”
10 ga. Welded steel
2" to 8"
10 ga. Welded steel
2" to 8"
10 ga. Welded steel
2" to 8"
Height Adjustment
Rear Wheels (Fixed) (4 ply Turf Pnuematic)
Front Wheels (Caster) (4 ply Turf Pnuematic)
Blade Dia.
2 Cranks
2 Cranks
2 Cranks
2 Cranks
Two 15/600 x 6
Two 5.30/4.50 x 6
2-30”
Two 15/600 x 6
Two 5.30/4.50 x 6
2-30"
Two 15/600 x 6
Two 5.30/4.50 x 6
2-30"
Two 15/600 x 6
Two 5.30/4.50 x 6
2-30"
Engine Speed, Blades Running
CLUTCH TYPE
Engagement Speed
DIMENSIONS
3600 RPM
3600 RPM
3600 RPM
3600 RPM
Manual
Manual
Manual
Manual
Length
98”
60”
98"
60"
98"
60"
98"
60"
Width
Height
29”
29"
29"
29"
Weight
515 lbs
550 lbs.
580 lbs.
580 lbs.
HITCH
Hitch Type
ATV Tongue
ATV Tongue
ATV Tongue
ATV Tongue
TOUCH-UP PAINT COLOR
Pewter Gray, Krylon #1606
Pewter Gray, Krylon #1606
Pewter Gray, Krylon #1606
Pewter Gray, Krylon #1606
14
Download from Www.Somanuals.com. All Manuals Search And Download.
ACREASE ROUGH CUT MOWER PARTS LIST
Item Part #
Description
Quantity
1
2
3
4
5
5
6
7
8
214021
216002
216009
222005
225003
225005
226003
226004
238004
241001
241009
241010
258022
Cup Washer
Wire Lock Pin, .31" x 2.50"
Screw Pin Shackle Clevis
6
2
1
2
1
1
2
2
1
1
1
1
2
Worm Drive Hose Clamp (7-7/8" to 9-1/8" Clamping Dia.)
Compression Spring, 3"L x 1-3/32" O.D. x .135" Wire dia.
Compression Spring, 4.50"L x 1-3/32" O.D. x .125" Wire dia.
Offset Wheel Assy. (15/600 x 6, 2 Ply Turf)
Centered Wheel Assy. (5.30/4.50 x 6, 2 Ply Stud)
"V" Belt, .62" x 95.9" O.C.
Flat Idler, 4" O.D. x 3/8" Hole
Flat Idler (Steel), 4" O.D. x 1/2" Hole
"V" Sheave, 5" Dia. 1" Bore
9
10
11
12
Spindle Assy.
900075 Spindle Shaft (1)
900160 Housing Assy. (With Two Bearings) (1)
243006 Bearing (6206 w/ Trash Guard Seals) (2)
600271 Bearing Spacer (3.33" Long) (1)
241008 Sheave, (7-1/2" Dia., B-Section) (1)
13
14
15
16
17
17
17
18
18
18
19
19
19
19
19
19
19
19
20
21
22
23
24
24
25
26
27
28
29
30
259002
Offset Mower Blade, 2-1/2" Wide, 30" Long, 3/4" Hole
Solenoid (Only on Models MR55B-17.5HP, MR55B-22-23HP & MR55T)
Hour/Tack Meter
2
1
264000
264003
264010
269000
269007
269010
269001
269008
269009
275001
275002
275003
275011
275007
275019
275021
275022
277002
277010
277011
277013
600071
600173
600126
600133
600136
600142
600143
600146
Optional
Ignition Switch
1
1
1
1
1
1
1
1
1
2
1
2
1
1
1
6
1
1
1
1
1
1
2
1
2
1
2
Choke Control, 20" (Model MR55B-17.5HP & MR55T)
Choke Control, 22.5" (Model MR55K)
Choke Control, 27" (Model MR55B-22-23HP)
Throttle Control, 15" (Model MR55B-17.5HP & MR55T)
Throttle Control, 46" (Model MR55K)
Throttle Control, 27" (Model MR55B-22-23HP)
Control Panel Decal, Starting Instructions
Warning Decal General
Danger Decal, Cut Finger
Clutch Engagement Decal
Warning Decal, Belt Sheild
Name Decal,Kunz
Name Decal, AcrEase
Name Decal, 57" Rough Cut
Rubber Gromet
Fuel Tank, 3.75 Gal. (Plastic)(Use Gas Cap 277013)
Handle Grip
Gas Cap (For Fuel Tank 277010)
Spacer, 1.38" O.D. x 1.33" Wall x 2.19" Long (MR55B & MR55T)
Spacer, 1.38" O.D. x 1.33" Wall x 2.25" Long (MR55K)
Flap Retainer Strip
Belt Sheild
Brake Stud
Upper Pivot Support
Safety Belting
Crank Arm
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Item Part #
Description
Quantity
31
32
33
34
35
36
37
38
600189
900023
900049
900058
900061
900062
900063
900065
Idler Spacer Block
Control Panel
Battery Box Assy.
Hitch Pivot
Pivot Arm
Height Adjust Nut
Clutch Arm
1
1
1
1
4
2
1
1
2
2
1
1
1
1
1
2
4
2
2
Idler Arm Assy.
243005 Bronze Bearing, 1/2"I.D. x 3/4" O.D. x .75" Long
900066
39
40
41
41
42
43
44
Screw Adjuster
Mower Deck
Engine Support Bracket (Model MR55B-17.5HP & MR55T)
Engine Support Bracket (Model MR55K & MR55B-22-23HP)
Tank Support
Tongue
Carrier Arm
900069
900071
600172
900079
900082
900106
243010 Plastic Bearing, 1-3/8" O.D. x 1.00" I.D.
900148
222012 Single Split Collar (1" I.D. x .1/2" Thick)
45
Caster Fork
16
Download from Www.Somanuals.com. All Manuals Search And Download.
ACREASE ROUGH CUT MOWER PARTS
17
Download from Www.Somanuals.com. All Manuals Search And Download.
OPTIONAL EQUIPMENT
OPTIONAL WETLANDS KIT
The optional wetlands kit features an extra set of tires for added ground support in soft or water
saturated areas. The following are applications and features that the wetlands kit works best in.
•
•
•
•
•
•
Great for wetlands or marshy areas that stay wet all year around.
Works well in combination with small personal amphibious vehicles or tracked ATVs.
More than doubles the tire surface area in contact with the ground.
Very easy to install bolt-on kit.
Works on all existing and new rough cut mowers.
The rough cut mower will not float with the wetlands kit installed. Water greater than 2-3" in
depth should be avoided.
•
With the Wetlands Kit installed the minimum cutting height is 3.5” – 4”.
Wetlands Kit (Part # 003905)
18
Download from Www.Somanuals.com. All Manuals Search And Download.
OPTIONAL EQUIPMENT
OPTIONAL ELECTRIC LIFT KIT
The optional electric lift kit consists of all of the mounting hardware, brackets, electric actuator and
wiring with remote control panel.
•
Great for constantly changing terrain and grass/brush heights.
Allows for quick cutting height changes on the go from the seat of the tow vehicle.
Raise up and over rocks and logs with ease.
Heavy duty 1500 lb linear screw actuator made by Linak.
Works on all existing and new rough cut mowers.
•
•
•
•
Electric Lift Kit (Part # 003909)
19
Download from Www.Somanuals.com. All Manuals Search And Download.
OPTIONAL EQUIPMENT
OPTIONAL FLOATATION KIT
The optional floatation kit consists of one additional front and rear tire, mounting brackets and
hardware.
•
Great for mowing around ponds and on rough uneven ground where scalping would normally
occur.
•
Clamping style receiver allows for adjustments from side to side with both the front and rear
tires.
•
•
Pinned receivers make for quick kit removal when not needed.
Works on all existing and new rough cut mowers.
Part numbers needed for standard manual lift rough cut models.
Rear Floatation Kit (Part # 003907)
Front Floatation Kit (Part # 003908)
Cross Brace Tube (Part # 900113) (Purchase one brace for each front and rear kit)
Part numbers needed for rough cut models with the electric lift kit.
Rear Floatation Kit (Part # 003907)
Front Floatation Kit (Part # 003908)
20
Download from Www.Somanuals.com. All Manuals Search And Download.
|