Jonsered Lawn Mower LT2226 A2 User Guide

J O N S E R E D S E R V I C E  
03090  
LT2226 A2  
Operator's Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY RULES  
Safe Operation Practices for Ride-On Mowers  
GENERAL SERVICE  
III. CHILDREN  
Never operate machine in a closed area.  
Keep all nuts and bolts tight to be sure the equipment  
is in safe working condition.  
Tragic accidents can occur if the operator is not alert to  
the presence of children. Children are often attracted to  
the machine and the mowing activity. Never assume that  
children will remain where you last saw them.  
Never tamper with safety devices. Check their proper  
operation regularly.  
Keepchildrenoutofthemowingareaandinthewatchful  
care of a responsible adult other than the operator.  
Be alert and turn machine off if a child enters the  
area.  
Before and while backing, look behind and down for  
small children.  
Nevercarrychildren,evenwiththebladesshutoff. They  
may fall off and be seriously injured or interfere with  
safemachineoperation.Childrenwhohavebeengiven  
rides in the past may suddenly appear in the mowing  
area for another ride and be run over or backed over  
by the machine.  
Never allow children to operate the machine.  
Useextracarewhenapproachingblindcorners,shrubs,  
trees, or other objects that may block your view of a  
child.  
Keep machine free of grass, leaves, or other debris  
build-up. Clean oil or fuel spillage and remove any  
fuel-soaked debris. Allow machine to cool before  
storing.  
If you strike a foreign object, stop and inspect the  
machine. Repair, if necessary, before restarting.  
Nevermakeanyadjustmentsorrepairswiththeengine  
running.  
Check grass catcher components and the discharge  
guard frequently and replace with manufacturer's rec-  
ommended parts, when necessary.  
Mower blades are sharp. Wrap the blade or wear  
gloves, and use extra caution when servicing them.  
Check brake operation frequently. Adjust and service  
as required.  
Maintain or replace safety and instruction labels, as  
necessary.  
IV. TOWING  
Tow only with a machine that has a hitch designed for  
towing. Do not attach towed equipment except at the  
hitch point.  
Follow the manufacturer's recommendation for weight  
limits for towed equipment and towing on slopes.  
Never allow children or others in or on towed equip-  
ment.  
On slopes, the weight of the towed equipment may  
cause loss of traction and loss of control.  
Travel slowly and allow extra distance to stop.  
Be sure the area is clear of bystanders before operat-  
ing. Stop machine if anyone enters the area.  
Never carry passengers.  
Do not mow in reverse unless absolutely necessary.  
Always look down and behind before and while back-  
ing.  
Nevercarrychildren,evenwiththebladesshutoff. They  
may fall off and be seriously injured or interfere with  
safemachineoperation.Childrenwhohavebeengiven  
rides in the past may suddenly appear in the mowing  
area for another ride and be run over or backed over  
by the machine.  
Keepchildrenoutofthemowingareaandinthewatchful  
care of a responsible adult other than the operator.  
Be alert and turn machine off if a child enters the  
area.  
Before and while backing, look behind and down for  
small children.  
Mow up and down slopes (15° Max), not across.  
Choose a low ground speed so that you will not have  
to stop or shift while on the slope.  
Avoid starting, stopping, or turning on a slope. If the  
tires lose traction, disengage the blades and proceed  
slowly straight down the slope.  
V. SERVICE  
SAFE HANDLING OF GASOLINE  
To avoid personal injury or property damage, use extreme  
careinhandlinggasoline. Gasolineisextremelyflammable  
and the vapors are explosive.  
Extinguish all cigarettes, cigars, pipes, and other  
sources of ignition.  
Use only approved gasoline container.  
Never remove gas cap or add fuel with the engine  
running. Allow engine to cool before refueling.  
Never fuel the machine indoors.  
Never store the machine or fuel container where there  
is an open flame, spark, or pilot light such as on a water  
heater or other appliances.  
Never fill containers inside a vehicle or on a truck or  
trailer bed with plastic liner. Always place containers  
on the ground away from your vehicle when filling.  
Remove gas-powered equipment from the truck or  
trailer and refuel it on the ground. If this is not possible,  
then refuel such equipment with a portable container,  
rather than from a gasoline dispenser nozzle.  
Keepthenozzleincontactwiththerimofthefueltankor  
container opening at all times until fueling is complete.  
Do not use a nozzle lock-open device.  
If fuel is spilled on clothing, change clothing immedi-  
ately.  
Never overfill fuel tank. Replace gas cap and tighten  
securely.  
If machine stops while going uphill, disengage blades,  
shift into reverse and back down slowly.  
Do not turn on slopes unless necessary, and then, turn  
slowly and gradually downhill, if possible.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
PRODUCT SPECIFICATIONS  
CUSTOMER RESPONSIBILITIES  
Gasoline Capacity  
and type:  
4 Gallons  
Read and observe the safety rules.  
Unleaded Regular  
Follow a regular schedule in maintaining, caring for  
and using your tractor.  
Oil Type (API-SG-SL):  
SAE 30 (above 32°F)  
SAE 5W-30 (below 32°F)  
Follow the instructions under “Maintenance” and “Stor-  
age” sections of this owner’s manual.  
Oil Capacity:  
W/ Filter:  
W/O Filter:  
64 oz  
60 oz  
Spark Plug:  
Champion QC12YC  
(Gap: .040")  
WARNING: This tractor is equipped with an internal com-  
bustion engine and should not be used on or near any un-  
improved forest-covered, brush-covered or grass-covered  
land unless the engine’s exhaust system is equipped with  
a spark arrester meeting applicable local or state laws (if  
any). If a spark arrester is used, it should be maintained  
in effective working order by the operator.  
Ground Speed (MPH):  
Forward:  
Reverse:  
0 – 5.5  
0 – 2.4  
Charging System:  
Battery:  
16 Amps @ 3600 RPM  
AMP/HR:  
MIN. CCA:  
Case Size:  
28  
230  
U1R  
In the state of California the above is required by law  
(Section 4442 of the California Public Resources Code).  
Other states may have similar laws. Federal laws apply  
on federal lands.  
Blade Bolt Torque:  
45-55 FT. LBS.  
CONGRATULATIONS on your purchase of a new tractor.  
Ithasbeendesigned,engineeredandmanufacturedtogive  
you the best possible dependability and performance.  
A spark arrester for the muffler is available through your  
nearest authorized service center/department.  
Shouldyouexperienceanyproblemyoucannoteasilyrem-  
edy, please contact your nearest authorized servicecenter/  
department We have competent, well-trained technicians  
and the proper tools to service or repair this tractor.  
Please read and retain this manual. The instructions will  
enable you to assemble and maintain your tractor properly.  
Always observe the “SAFETY RULES”.  
TABLE OF CONTENTS  
SAFETY RULES .........................................................2-3  
PRODUCT SPECIFICATIONS....................................... 4  
CUSTOMER RESPONSIBILITIES................................. 4  
ASSEMBLY.................................................................5-6  
OPERATION .............................................................7-13  
MAINTENANCE SCHEDULE ...................................... 14  
MAINTENANCE..................................................... 14-17  
SERVICE AND ADJUSTMENTS............................18-23  
STORAGE.................................................................... 24  
TROUBLESHOOTING............................................25-26  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
UNASSEMBLED PARTS  
Slope Sheet  
Key  
(1) Oil Drain Tube  
(2) Keys  
ASSEMBLY  
Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping  
purpose.  
Whenrightorlefthandismentionedinthismanual,itmeans  
when you are in the operating position (seated behind the  
steering wheel).  
NEGATIVE  
(BLACK)CABLE  
L
TO REMOVE TRACTOR FROM  
CARTON  
UNPACK CARTON  
Remove all accessible loose parts and parts cartons  
from carton.  
Cut along dashed lines on all four panels of carton.  
Remove end panels and lay side panels flat.  
Check for any additional loose parts or cartons and  
remove.  
POSITIVE  
(RED)CABLE  
02954  
CONNECT BATTERY (See Fig. 1)  
Fig. 1  
CAUTION: Do not short battery termi-  
ADJUST SEAT (See Fig. 2)  
nals by allowing a wrench or any other  
object to contact both terminals at the  
same time. Before connecting battery,  
remove metal bracelets, wristwatch  
bands,rings,etc.Positiveterminalmust  
be connected first to prevent sparking  
from accidental grounding.  
Sit in seat.  
Lift up adjustment lever (A) and slide seat until a com-  
fortable position is reached which allows you to press  
clutch/brake pedal all the way down.  
Release lever to lock seat in position.  
Lift hood to raised position.  
Remove terminal protective caps and discard.  
A
NOTE: If this battery is put into service after month and  
yearindicatedonlabel(L)(labellocatedbetweenterminals)  
charge battery for minimum of one hour at 6-10 amps.  
First connect RED battery cable to positive (+) terminal  
with hex bolt and keps nut.  
ConnectBLACKgroundingcabletonegative(-)terminal  
withremaininghexboltandkepsnut. Tightensecurely.  
Fig. 2  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
NOTE: You may now roll your tractor off the skid. Follow  
CHECKLIST  
the appropriate instruction below to remove the tractor  
from the skid.  
BEFORE YOU OPERATE YOUR NEW TRACTOR, WE  
WISHTOASSURETHATYOURECEIVETHEBESTPER-  
FORMANCEANDSATISFACTIONFROMTHISQUALITY  
PRODUCT.  
WARNING:Beforestarting,read,understandandfollow  
all instructions in the Operation section of this manual. Be  
sure tractor is in a well-ventilated area. Be sure the area in  
front of tractor is clear of other people and objects.  
PLEASE REVIEW THE FOLLOWING CHECKLIST:  
All assembly instructions have been completed.  
TO ROLL TRACTOR OFF SKID (See Op-  
eration section for location and function of  
controls)  
No remaining loose parts in carton.  
Battery is properly prepared and charged.  
Seat is adjusted comfortably and tightened securely.  
All tires are properly inflated. (For shipping purposes,  
the tires were overinflated at the factory).  
Be sure mower deck is properly leveled side-to-side/  
front-to-rear for best cutting results. (Tires must be  
properly inflated for leveling).  
Check mower and drive belts. Be sure they are routed  
properly around pulleys and inside all belt keepers.  
Check wiring. See that all connections are still secure  
and wires are properly clamped.  
Before driving tractor, be sure freewheel control is in  
“transmission engaged” position (see “TO TRANS-  
PORT” in the Operation section of this manual).  
Raise attachment lift lever to its highest position.  
Release parking brake by depressing brake pedal.  
Place freewheel control in disengaged position to dis-  
engage transmission (See “TO TRANSPORT” in the  
Operation section of this manual).  
Roll tractor forward off skid.  
CHECK TIRE PRESSURE  
The tires on your tractor were overinflated at the factory  
for shipping purposes. Correct tire pressure is important  
for best cutting performance.  
Reduce tire pressure to PSI shown on tires.  
WHILE LEARNING HOW TO USE YOUR TRACTOR, PAY  
EXTRA ATTENTION TO THE FOLLOWING IMPORTANT  
ITEMS:  
CHECK DECK LEVELNESS  
For best cutting results, mower housing should be prop-  
erly leveled. See “TO LEVEL MOWER HOUSING” in the  
Service and Adjustments section of this manual.  
Engine oil is at proper level.  
Fuel tank is filled with fresh, clean, regular unleaded  
gasoline.  
Become familiar with all controls, their location and  
function. Operate them before you start the engine.  
Be sure brake system is in safe operating condition.  
Be sure Operator Presence System and Reverse Op-  
eration System (ROS) are working properly (See the  
Operation and Maintenance sections in this manual).  
It is important to purge the transmission before op-  
erating your tractor for the first time. Follow proper  
starting and transmission purging instructions (See  
“TOSTARTENGINEandPURGETRANSMISSION”  
in the Operation section of this manual).  
CHECK FOR PROPER POSITION OF ALL  
BELTS  
See the figures that are shown for replacing motion and  
mower blade drive belts in the Service and Adjustments  
section of this manual. Verify that the belts are routed  
correctly.  
CHECK BRAKE SYSTEM  
Afteryoulearnhowtooperateyourtractor,checktoseethat  
the brake is operating properly. See “TO CHECK BRAKE”  
in the Service and Adjustments section of this manual.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning.  
FAST  
SLOW  
REVERSE  
HIGH  
LOW  
NEUTRAL  
CHOKE  
IGNITION SWITCH  
MOWER LIFT  
ENGINE START  
MOWER HEIGHT  
ENGINE ON  
PARKING BRAKE  
REVERSE  
OPERATION  
SYSTEM (ROS)  
ENGINE OFF  
CLUTCH/BRAKE  
PEDAL  
LIGHTS ON  
CRUISE CONTROL  
BATTERY  
REVERSE  
FUEL  
FORWARD  
15  
15  
ATTACHMENT  
CLUTCH ENGAGED  
DANGER, KEEP HANDS  
AND FEET AWAY  
ATTACHMENT  
CLUTCH DISENGAGED  
SLOPE HAZARDS  
KEEP AREA CLEAR  
(SEE SAFETY RULES SECTION)  
DANGER indicates a hazard which, if not avoided,  
will result in death or serious injury.  
WARNING indicates a hazard which, if not avoided,  
could result in death or serious injury.  
FREE WHEEL  
(Automatic Models only)  
CAUTION indicates a hazard which, if not avoided,  
might result in minor or moderate injury.  
CAUTION when used without the alert symbol,  
indicates a situation that could result in damage  
to the tractor and/or engine.  
Failure to follow instructions  
could result in serious injury or  
death. The safety alert symbol  
is used to identify safety inform-  
ation about hazards which can  
result in death, serious injury  
and/or property damage.  
HOT SURFACES indicates a hazard which,  
if not avoided, could result in death, serious injury  
and/or property damage.  
FIRE indicates a hazard which, if not avoided,  
could result in death, serious injury and/or  
property damage.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
KNOW YOUR TRACTOR  
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR  
Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments.  
Save this manual for future reference.  
D
E
P
H
N
B
J
K
G
F
A
C
L
M
Fig. 3  
Our tractors conform to the applicable safety standards of the American National Standards Institute.  
(A) ATTACHMENT LIFT LEVER – Used to raise and  
lower the mower or other attachments mounted to your  
tractor.  
(B) BRAKE PEDAL – Used for braking the tractor and  
starting the engine.  
(C) PARKING BRAKE – Locks clutch/brake pedal into  
the brake position.  
(H) LIGHT SWITCH Turns the headlights on and off.  
(N) CHOKE CONTROL - Used when starting a cold  
engine.  
(J) CRUISE CONTROL LEVER – Used to set forward  
movement of tractor at desired speed without holding  
the forward drive pedal.  
(K) FORWARD DRIVE PEDAL – Used for forward  
movement of tractor.  
(D) THROTTLE - Used for starting and controlling engine  
speed.  
(L) REVERSE DRIVE PEDAL – Used for reverse  
(E) ATTACHMENT CLUTCH SWITCH – Used to engage  
the mower blades, or other attachments mounted to your  
tractor.  
(F) IGNITION SWITCH – Used for starting and stopping  
the engine.  
(G) REVERSE OPERATION SYSTEM (ROS) "ON"  
POSITION – Allows operation of mower or other  
powered attachment while in reverse.  
movement of tractor.  
(M) FREEWHEEL CONTROL – Disengages  
transmission for pushing or slowly towing the tractor  
with the engine off.  
(P) SERVICE REMINDER / HOUR METER – Indicates  
when service is required for the engine and mower.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
The operation of any tractor can result in foreign objects thrown into the eyes, which can result  
in severe eye damage. Always wear safety glasses or eye shields while operating your tractor  
or performing any adjustments or repairs. We recommend standard safety glasses or a wide  
vision safety mask worn over spectacles.  
TO USE THROTTLE CONTROL - D (See Fig. 5)  
Always operate engine at full speed (fast).  
HOW TO USE YOUR TRACTOR  
TO SET PARKING BRAKE(See Fig. 4)  
Operating engine at less than full speed (fast) reduces  
engines operating efficiency.  
Your tractor is equipped with an operator presence sens-  
ing switch. When engine is running, any attempt by the  
operator to leave the seat without first setting the parking  
brake will shut off the engine.  
Full speed (fast) offers the best bagging and mower  
performance.  
D
Depress brake pedal (B) all the way down and hold.  
Pull parking brake lever (C) up and hold, release pres-  
sure from brake pedal (B), then release parking brake  
lever. Pedal should remain in brake position. Make  
sure parking brake will hold tractor secure.  
N
Fig. 5  
B
TO USE CHOKE CONTROL (See Fig. 5)  
Usechokecontrolwheneveryouarestartingacoldengine.  
Do not use to start a warm engine.  
C
To engage choke control (N), pull knob out. Slowly  
push knob in to disengage.  
Fig. 4  
TO MOVE FORWARD AND BACKWARD  
(See Fig. 6)  
The direction and speed of movement is controlled by the  
forward and reverse drive pedals.  
STOPPING (See Fig. 3)  
MOWER BLADES -  
To stop mower blades,move attachment clutch lever  
to “DISENGAGED” position.  
Start tractor and release parking brake.  
Slowlydepressforward(K)orreverse(L)drivepedalto  
begin movement. Ground speed increases the further  
down the pedal is depressed.  
GROUND DRIVE -  
To stop ground drive, depress brake pedal into full  
“BRAKE” position.  
IMPORTANT: FORWARD AND REVERSE DRIVE  
PEDALS RETURN TO NEUTRAL POSITION WHEN NOT  
DEPRESSED.  
ENGINE -  
TO USE CRUISE CONTROL -J (See Fig. 6)  
The cruise control feature can be used for forward travel  
only.  
SYSTEM CHARACTERISTICS  
Move throttle control between half and full speed (fast)  
position.  
The cruise control should only be used while mowing or  
transporting on relatively smooth, straight surfaces. Other  
conditions such as trimming at slow speeds may cause the  
cruise control to disengage. Do not use the cruise control  
on slopes, rough terrian or while trimmimg or turning.  
NOTE: Failure to move throttle control between half and  
fullspeed(fast)position,beforestoppingmaycauseengine  
to “backfire”.  
Turn ignition key to “STOP” position and remove key.  
Always remove key when leaving tractor to prevent  
unauthorized use.  
With forward drive pedal depressed to desired speed,  
pull cruise control lever (J) up and hold while lifting  
your foot off the pedal, then release the lever.  
Never use choke to stop engine.  
To disengage the cruise control, depress the brake pedal  
or tap on forward drive pedal.  
IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY  
POSITION OTHER THAN "STOP" WILL CAUSE THE BATTERY  
TO BE DISCHARGED, (DEAD).  
J
K
NOTE: Under certain conditions when tractor is standing  
idlewiththeenginerunning, hotengineexhaustgasesmay  
cause “browning” of grass. To eliminate this possibility, al-  
ways stop engine when stopping tractor on grass areas.  
L
CAUTION: Always stop tractor com-  
pletely,asdescribedabove,beforeleav-  
ing the operator's position; to empty  
grass catcher, etc.  
9
Fig. 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
TO OPERATE MOWER  
TO ADJUST MOWER CUTTING HEIGHT  
Yourtractorisequippedwithanoperatorpresencesensing  
switch. Any attempt by the operator to leave the seat with  
the engine running and the attachment clutch engaged will  
shut off the engine. You must remain fully and centrally  
positioned in the seat to prevent the engine from hesitat-  
ing or cutting off when operating your equipment on rough,  
rolling terrain or hills.  
(See Fig. 7)  
The position of the attachment lift lever (A) determines the  
cutting height.  
Select desired height of cut with attachment lift lever.  
Start mower blades by engaging attachment clutch  
control.  
A
TO STOP MOWER BLADES -  
disengage attachment clutch control.  
CAUTION: Do not operate the mower  
Fig. 7  
without either the entire grass catcher,  
onmowerssoequipped,orthedeflector  
shield (S) in place. (See Fig. 9)  
Put attachment lift lever in desired cutting height slot.  
The cutting height range is approximately 1" to 4". The  
heights are measured from the ground to the blade tip with  
the engine not running. These heights are approximate  
and may vary depending upon soil conditions, height of  
grass and types of grass being mowed.  
S
Theaveragelawnshouldbecuttoapproximately2-1/2  
inches during the cool season and to over 3 inches  
during hot months. For healthier and better looking  
lawns, mow often and after moderate growth.  
For best cutting performance, grass over 6 inches  
in height should be mowed twice. Make the first cut  
relatively high; the second to desired height.  
Fig. 9  
REVERSE OPERATION SYSTEM (ROS)  
(See Fig. 10)  
Your tractor is equipped with a Reverse Operation System  
(ROS). Any attempt by the operator to travel in the reverse  
direction with the attachment clutch engaged will shut off  
the engine unless ignition key is placed in the ROS "ON"  
position.  
TO ADJUST GAUGE WHEELS (See Fig. 8)  
Gaugewheels areproperlyadjustedwhentheyareslightly  
off the ground when mower is at the desired cutting height  
in operating position. Gauge wheels then keep the deck  
in proper position to help prevent scalping in most terrain  
conditions.  
WARNING: Backing up with the attachment clutch en-  
gaged while mowing is strongly discouraged. Turning the  
ROS "ON", to allow reverse operation with the attachment  
clutch engaged, should only be done when the operator  
decides it is necessary to reposition the machine with the  
attachment engaged. Do not mow in reverse unless  
absolutely necessary.  
NOTE: Adjust gauge wheels with tractor on a flat level  
surface.  
Adjust mower to desired cutting height (See “TO AD-  
JUST MOWER CUTTING HEIGHT” in this section of  
manual).  
With mower in desired height of cut position, gauge  
wheels should be assembled so they are slightly off  
the ground. Install gauge wheel in appropriate hole.  
Tighten securely.  
USING THE REVERSE OPERATION SYSTEM -  
Only use if you are certain no children or other bystanders  
will enter the mowing area.  
Repeat for all, installing gauge wheel in same adjust-  
ment hole.  
Depress brake pedal all the way down.  
Withenginerunning,turnignitionkeycounterclockwise  
to ROS "ON" position.  
Look down and behind before and while backing.  
Slowly depress reverse drive pedal to start movement.  
When use of the ROS is no longer needed, turn the  
ignition key clockwise to engine "ON" position.  
Fig. 8  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
SERVICE REMINDER/HOUR METER  
Serviceremindershowsthetotalnumberofhourstheengine  
has run and flashes to indicate that the engine or mower  
needs servicing. When service is required, the service  
reminder will flash for two hours. To service engine and  
mower, see the Maintenance section of this manual.  
NOTE: Service reminder runs when the ignition key is in  
any position but "STOP". For accurate reading, be sure  
key remains in the "STOP" position when engine is not  
running.  
ROS "ON" POSITION  
ENGINE "ON" POSITION  
(NORMAL OPERATING)  
Fig. 10  
TOWING CARTS AND OTHER ATTACHMENTS  
TO OPERATE ON HILLS  
Tow only the attachments that are recommended by and  
complywithspecificationsofthemanufacturerofyourtrac-  
tor. Use common sense when towing. Too heavy of a load,  
while on a slope, is dangerous. Tires can lose traction with  
the ground and cause you to lose control of your tractor.  
CAUTION: Donotdriveupordownhills  
with slopes greater than 15° and do not  
drive across any slope.  
Choose the slowest speed before starting up or down  
hills.  
BEFORE STARTING THE ENGINE  
CHECK ENGINE OIL LEVEL  
The engine in your tractor has been shipped, from the  
factory, already filled with summer weight oil.  
Avoid stopping or changing speed on hills.  
If stopping is absolutely necessary, push brake pedal  
quickly to brake position and engage parking brake.  
Torestartmovement, slowlyreleaseparkingbrakeand  
brake pedal.  
Slowly depress appropriate drive pedal to slowest set-  
ting.  
Check engine oil with tractor on level ground.  
Remove oil fill cap/dipstick and wipe clean, reinsert the  
dipstick and screw cap tight, wait for a few seconds,  
remove and read oil level. If necessary, add oil until  
“FULLmark on dipstick is reached. Do not overfill.  
For cold weather operation you should change oil for  
easier starting (See “OIL VISCOSITY CHART” in the  
Maintenance section of this manual).  
Make all turns slowly.  
TO TRANSPORT (See Figs. 3 and 11)  
When pushing or towing your tractor, be sure to disengage  
transmission by placing freewheel control in freewheeling  
position. Free wheel control is located at the rear drawbar  
of tractor.  
To change engine oil, see the Maintenance section in  
this manual.  
ADD GASOLINE  
Raiseattachmentlifttohighestpositionwithattachment  
lift control.  
Pull freewheel control out and down into the slot and  
release so it is held in the disengaged position.  
Do not push or tow tractor at more than two (2)  
MPH.  
To reengage transmission, reverse above procedure.  
Fill fuel tank to bottom of filler neck. Do not overfill. Use  
fresh, clean, regularunleadedgasolinewithaminimumof  
87 octane. (Use of leaded gasoline will increase carbon  
and lead oxide deposits and reduce valve life). Do not  
mix oil with gasoline. Purchase fuel in quantities that can  
be used within 30 days to assure fuel freshness.  
CAUTION: Wipe off any spilled oil or  
fuel. Do not store, spill or use gasoline  
near an open flame.  
NOTE: To protect hood from damage when transporting  
your tractor on a truck or a trailer, be sure hood is closed  
and secured to tractor. Use an appropriate means of tying  
hood to tractor (rope, cord, etc.).  
IMPORTANT: WHEN OPERATING IN TEMPERATURES  
BELOW32°F(0°C),USEFRESH,CLEANWINTERGRADE  
GASOLINE TO HELP INSURE GOOD COLD WEATHER  
STARTING.  
Transmission Engaged  
CAUTION: Alcohol blended fuels (called gasohol  
or using ethanol or methanol) can attract moisture  
which leads to separation and formation of acids  
during storage. Acidic gas can damage the fuel  
systemofanenginewhileinstorage. Toavoidengine  
problems, the fuel system should be emptied before  
storage of 30 days or longer. Drain the gas tank,  
start the engine and let it run until the fuel lines and  
carburetor are empty. Use fresh fuel next season.  
See Storage Instructions for additional information.  
Never use engine or carburetor cleaner products in  
the fuel tank or permanent damage may occur.  
Transmission Disengaged  
Fig. 11  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
PURGE TRANSMISSION  
TO START ENGINE (See Fig. 3)  
When starting the engine for the first time or if the engine  
has run out of fuel, it will take extra cranking time to move  
fuel from the tank to the engine.  
CAUTION: Never engage or disengage  
freewheel lever while the engine is  
running.  
Besurefreewheelcontrolisinthetransmissionengaged  
position.  
Sit on seat in operating position, depress brake pedal  
and set parking brake.  
Move attachment clutch to “DISENGAGED” position.  
Move throttle control to fast position  
Pull choke control out for a cold engine start attempt.  
For a warm engine start attempt the choke control may  
not be needed.  
To ensure proper operation and performance, it is recom-  
mended that the transmission be purged before operating  
tractor for the first time. This procedure will remove any  
trapped air inside the transmission which may have de-  
veloped during shipping of your tractor.  
IMPORTANT: SHOULD YOUR TRANSMISSION  
REQUIREREMOVALFORSERVICEORREPLACEMENT,  
IT SHOULD BE PURGED AFTER REINSTALLATION  
BEFORE OPERATING THE TRACTOR.  
NOTE: Before starting, read the warm and cold starting  
procedures below.  
Place tractor safely on a level surface - that is clear  
and open - with engine off and parking brake set.  
Insert key into ignition and turn key clockwise to  
“START” position and release key as soon as engine  
starts. Do not run starter continuously for more than  
fifteen seconds per minute. If the engine does not start  
after several attempts, push choke control in, wait a  
few minutes and try again. If engine still does not start,  
pull the choke control out and retry.  
Disengage transmission by placing freewheel control  
in freewheeling position (See “TO TRANSPORT” in  
this section of manual).  
Sitting in the tractor seat, start engine. After the en-  
gine is running, move throttle control to slow position.  
Disengage parking brake  
WARM WEATHER STARTING (50° F and above)  
When engine starts, slowly push choke control in until  
the engine begins to run smoothly. If the engine starts  
to run roughly, pull the choke control out slightly for a  
few seconds and then continue to push the control in  
slowly.  
The attachments and ground drive can now be used. If  
the engine does not accept the load, restart the engine  
and allow it to warm up for one minute using the choke  
as described above.  
CAUTION: At any time, during step 4,  
there may be movement of the drive  
wheels.  
Depress forward drive pedal to full forward position,  
hold for five (5) seconds and release pedal. Depress  
reverse drive pedal to full reverse position, hold for five  
(5) seconds and release pedal. Repeat this procedure  
three (3) times.  
COLD WEATHER STARTING (50° F and below)  
Shut- off engine and set parking brake.  
When engine starts, slowly push choke control in until  
the engine begins to run smoothly. Continue to push  
the choke control in small steps allowing the engine to  
acceptsmallchangesinspeedandload,untilthechoke  
control is fully in. If the engine starts to run roughly, pull  
the choke control out slightly for a few seconds and  
then continue to push the control in slowly. This may  
requireanenginewarm-upperiodfromseveralseconds  
to several minutes, depending on the temperature.  
Engage transmission by placing freewheel control in  
engaged position (See “TO TRANSPORT” in this sec-  
tion of manual).  
Sitting in the tractor seat, start engine. After the engine  
is running, move throttle control to half (1/2) speed.  
Disengage parking brake.  
Drive tractor forward for approximately five feet then  
backwards for five feet. Repeat this driving procedure  
three times.  
AUTOMATIC TRANSMISSION WARM UP  
Beforedrivingtheunitincoldweather,thetransmission  
should be warmed up as follows:  
Your transmission is now purged and now ready for normal  
operation.  
Be sure the tractor is on level ground.  
Release the parking brake and let the brake slowly  
return to operating position.  
Allowoneminutefortransmissiontowarmup.This  
can be done during the engine warm up period.  
The attachments can be used during the engine warm-  
up period after the transmission has been warmed  
up and may require the choke control be pulled out  
slightly.  
NOTE: If at a high altitude (above 3000 feet) or in cold  
temperatures (below 32 F) the carburetor fuel mixture may  
need to be adjusted for best engine performance. See “TO  
ADJUST CARBURETOR” in the Service and Adjustments  
section of this manual.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
MOWING TIPS  
If grass is extremely tall, it should be mowed twice to  
Mower should be properly leveled for best mowing  
performance. See “TO LEVEL MOWER HOUSING” in  
the Service and Adjustments section of this manual.  
reduce load and possible fire hazard from dried clip-  
pings. Make first cut relatively high; the second to the  
desired height.  
Do not mow grass when it is wet. Wet grass will plug  
mower and leave undesirable clumps. Allow grass to  
dry before mowing.  
The left hand side of mower should be used for trim-  
ming.  
Drive so that clippings are discharged onto the area  
that has been cut. Have the cut area to the right of the  
machine. This will result in a more even distribution of  
clippings and more uniform cutting.  
Always operate engine at full throttle when mow-  
ing to assure better mowing performance and proper  
discharge of material. Regulate ground speed by  
selecting a low enough gear to give the mower cutting  
performance as well as the quality of cut desired.  
When operating attachments, select a ground speed  
that will suit the terrain and give best performance of  
the attachment being used.  
When mowing large areas, start by turning to the right  
so that clippings will discharge away from shrubs,  
fences, driveways, etc. After one or two rounds, mow  
in the opposite direction making left hand turns until  
finished (See Fig. 12).  
Fig. 12  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
BEFORE  
EACH  
USE  
EVERY  
8
HOURS  
EVERY  
25  
HOURS  
EVERY  
50  
HOURS  
EVERY  
100  
HOURS  
EVERY  
SEASON  
BEFORE  
STORAGE  
MAINTENANCE  
SCHEDULE  
Check Brake Operation  
T Check Tire Pressure  
R Check Operator Presence & ROS Systems  
A Check for Loose Fasteners  
Check/Replace Mower Blades  
3
4
C
T
0
Lubrication Chart  
Check Battery Level  
Clean Battery and Terminals  
Check Transaxle Cooling  
Check Mower Levelness  
Check V-Belts  
R
Check Engine Oil Level  
1,2  
Change Engine Oil (with oil filter)  
1,2  
E Change Engine Oil (without oil filter)  
N Clean Air Filter  
2
2
G Clean Air Screen  
Inspect Muffler/Spark Arrester  
I
N
1,  
2
2
Replace Oil Filter (If equipped)  
E Clean Engine Cooling Fins  
Replace Spark Plug  
Replace Air Filter Paper Cartridge  
Replace Fuel Filter  
2
1 - Change more often when operating under a heavy load or  
in high ambient temperatures.  
3 - Replace blades more often when mowing in sandy soil.  
4 - Not required if equipped with maintenance-free battery.  
2 - Service more often when operating in dirty or dusty conditions.  
LUBRICATION CHART  
GENERAL RECOMMENDATIONS  
SPINDLE ZERK  
SPINDLE ZERK  
The warranty on this tractor does not cover items that have  
beensubjectedtooperatorabuseornegligence. Toreceive  
full value from the warranty, operator must maintain tractor  
as instructed in this manual.  
FRONT  
WHEEL  
FRONT  
WHEEL  
BEARING  
ZERK  
BEARING  
ZERK  
Some adjustments will need to be made periodically to  
properly maintain your tractor.  
ENGINE  
At least once a season, check to see if you should make  
any of the adjustments described in the Service and  
Adjustments section of this manual.  
• At least once a year you should replace the spark  
plug, clean or replace air filter, and check blades and  
belts for wear. A new spark plug and clean air filter  
assure proper air-fuel mixture and help your engine  
run better and last longer.  
STEERING  
SECTOR GEAR  
TEETH  
02956  
BEFORE EACH USE  
General Purpose Grease  
Refer to Maintenance “ENGINE” Section  
Check engine oil level.  
Check brake operation.  
Check tire pressure.  
IMPORTANT: DO NOT OIL OR GREASE THE PIVOT POINTS  
WHICH HAVE SPECIAL NYLON BEARINGS. VISCOUS  
LUBRICANTS WILL ATTRACT DUST AND DIRT THAT WILL  
SHORTENTHELIFEOFTHESELF-LUBRICATINGBEARINGS.  
IFYOUFEELTHEYMUSTBELUBRICATED,USEONLYADRY,  
POWDERED GRAPHITE TYPE LUBRICANT SPARINGLY.  
Check operator presence and  
ROS systems for proper operation.  
Check for loose fasteners.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
BLADE CARE  
For best results mower blades must be sharp. Replace  
worn, bent or damaged blades.  
TRACTOR  
Always observe safety rules when performing any main-  
tenance.  
BRAKE OPERATION  
CAUTION:Useonlyareplacementblade  
approved by the manufacturer of your  
tractor. Using a blade not approved  
by the manufacturer of your tractor is  
hazardous, could damage your tractor  
and void your warranty.  
If tractor requires more than five (5) feet to stop at highest  
speed in highest gear on a level, dry concrete or paved  
surface, then brake must be serviced. (See “TO CHECK  
BRAKE” in the Service and Adjustments section of this  
manual).  
TIRES  
BLADE REMOVAL (See Fig. 13)  
Maintain proper air pressure in all tires (See PSI on  
tires).  
Raise mower to highest position to allow access to  
blades.  
Keep tires free of gasoline, oil, or insect control chemi-  
NOTE: Protect your hands with gloves and/or wrap blade  
with heavy cloth.  
cals which can harm rubber.  
Avoid stumps, stones, deep ruts, sharp objects and  
other hazards that may cause tire damage.  
Remove blade bolt by turning counterclockwise.  
Install new blade with stamped "GRASS SIDE" facing  
the ground.  
NOTE: To seal tire punctures and prevent flat tires due  
to slow leaks, tire sealant may be purchased from your  
local parts dealer. Tire sealant also prevents tire dry rot  
and corrosion.  
IMPORTANT: To ensure proper assembly, center hole in  
blade must align with star on mandrel assembly.  
Install and tighten blade bolt securely (45-55 Ft. Lbs.  
torque).  
OPERATOR PRESENCE SYSTEM AND REVERSE OP-  
ERATION SYSTEM (ROS)  
Be sure operator presence and reverse operation systems  
are working properly. If your tractor does not function as  
described, repair the problem immediately.  
IMPORTANT: Special blade bolt is heat treated.  
STAR  
BLADE  
CENTER  
HOLE  
The engine should not start unless the brake pedal is  
fully depressed, and the attachment clutch control is  
in the disengaged position.  
BLADE BOLT  
(SPECIAL)  
CHECK OPERATOR PRESENCE SYSTEM  
MANDREL  
ASSEMBLY  
Whentheengineisrunning,anyattemptbytheoperator  
to leave the seat without first setting the parking brake  
should shut off the engine.  
When the engine is running and the attachment clutch  
is engaged, any attempt by the operator to leave the  
seat should shut off the engine.  
Fig. 13  
BATTERY  
The attachment clutch should never operate unless  
the operator is in the seat.  
Yourtractorhasabatterychargingsystemwhichissufficient  
for normal use. However, periodic charging of the battery  
with an automotive charger will extend its life.  
Engine "ON" Position  
ROS "ON" Position  
(Normal Operating)  
Keep battery and terminals clean.  
Keep battery bolts tight.  
Keep small vent holes open.  
Recharge at 6-10 amperes for 1 hour.  
NOTE: The original equipment battery on your tractor is  
maintenance free. Do not attempt to open or remove caps  
or covers. Adding or checking level of electrolyte is not  
necessary.  
CHECK REVERSE OPERATION (ROS) SYSTEM  
When the engine is running with the ignition switch in  
the engine "ON" position and the attachment clutch  
engaged, any attempt by the operator to shift into  
reverse should shut off the engine.  
TO CLEAN BATTERY AND TERMINALS  
Corrosion and dirt on the battery and terminals can cause  
the battery to “leak” power.  
When the engine is running with the ignition switch in  
the ROS "ON" position and the attachment clutch en-  
gaged, any attempt by the operator to shift into reverse  
should NOT shut off the engine.  
Remove terminal guard.  
Disconnect BLACK battery cable first then RED bat-  
tery cable and remove battery from tractor.  
Rinse the battery with plain water and dry.  
Cleanterminalsandbattery cableends withwirebrush  
until bright.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
TO CHANGE ENGINE OIL (See Figs. 14 and 15)  
Coat terminals with grease or petroleum jelly.  
Reinstall battery (See “REPLACING BATTERY" in  
the SERVICE AND ADJUSTMENTS section of this  
manual).  
Determine temperature range expected before oil change.  
All oil must meet API service classification SG-SL.  
Be sure tractor is on level surface.  
Oil will drain more freely when warm.  
Catch oil in a suitable container.  
Remove oil fill cap/dipstick. Be careful not to allow dirt  
to enter the engine when changing oil.  
V-BELTS  
Check V-belts for deterioration and wear after 100 hours  
of operation and replace if necessary. The belts are not  
adjustable. Replace belts if they begin to slip from wear.  
Remove yellow cap from end of drain valve and install  
the drain tube onto the fitting.  
TRANSAXLE COOLING  
The transmission fan and cooling fins should be kept clean  
to assure proper cooling.  
OIL DRAIN VALVE  
Do not attempt to clean fan or transmission while engine  
is running or while the transmission is hot. To prevent pos-  
sible damage to seals, do not use high pressure water or  
steam to clean transaxle.  
CLOSED AND  
LOCKED  
POSITION  
Inspect cooling fan to be sure fan blades are intact and  
clean.  
YELLOW  
CAP  
Inspect cooling fins for dirt, grass clippings and other  
materials. To prevent damage to seals, do not use  
compressed air or high pressure sprayer to clean  
cooling fins.  
DRAIN  
TUBE  
TRANSAXLE PUMP FLUID  
Fig. 15  
The transaxle was sealed at the factory and fluid mainte-  
nance is not required for the life of the transaxle. Should  
the transaxle ever leak or require servicing, contact your  
nearest authorized service center/department.  
Unlock drain valve by pushing inward and turning  
counterclockwise.  
To open, pull out on the drain valve.  
After oil has drained completely, close and lock the  
drain valve by pushing inward and turning clockwise  
until the pin is in the locked position as shown.  
Remove the drain tube and replace the cap onto to the  
bottom fitting of the drain valve.  
Refill engine with oil through oil fill dipstick tube. Pour  
slowly. Do not overfill. For approximate capacity see  
“PRODUCT SPECIFICATIONS” section of this man-  
ual.  
ENGINE  
LUBRICATION  
Only use high quality detergent oil rated with API service  
classification SG-SL. Select the oil’s SAE viscosity grade  
according to your expected operating temperature.  
SAE VISCOSITY GRADES  
Use gauge on oil fill cap/dipstick for checking level.  
Be sure dipstick cap is tightened securely for accurate  
reading. Keep oil at “FULLline on dipstick. Tighten  
cap onto the tube securely when finished.  
SAE 30  
5W-30  
-20  
0
30  
32 40  
0
100  
60  
80  
F
C
-20  
10  
-30  
-10  
20  
30  
40  
TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE  
oil_visc_chart1_e  
Fig. 14  
CLEAN AIR SCREEN  
NOTE: Although multi-viscosity oils (5W30, 10W30 etc.)  
improvestartingincoldweather,theywillresultinincreased  
oilconsumptionwhenusedabove3F. Checkyourengine  
oil level more frequently to avoid possible engine damage  
from running low on oil.  
Air screen must be kept free of dirt and chaff to prevent  
engine damage from overheating. Clean with a wire brush  
or compressed air to remove dirt and stubborn dried gum  
fibers.  
Change the oil after every 50 hours of operation or at least  
once a year if the tractor is not used for 50 hours in one  
year.  
AIR FILTER  
Your engine will not run properly using a dirty air filter.  
Service air cleaner more often under dusty conditions.  
See Engine Manual.  
Check the crankcase oil level before starting the engine  
and after each eight (8) hours of operation. Tighten oil fill  
cap/dipstick securely each time you check the oil level.  
ENGINE OIL FILTER  
Replace the engine oil filter every season or every other  
oil change if the tractor is used more than 100 hours in  
one year.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
MUFFLER  
CLAMP  
Inspect and replace corroded muffler and spark arrester  
(if equipped) as it could create a fire hazard and/or dam-  
age.  
FUEL FILTER  
SPARK PLUGS  
Fig. 16  
Replace spark plugs at the beginning of each mowing  
season or after every 100 hours of operation, whichever  
occurs first. Spark plug type and gap setting are shown in  
“PRODUCT SPECIFICATIONS” section of this manual.  
CLEANING  
Clean engine, battery, seat, finish, etc. of all foreign  
matter.  
IN-LINE FUEL FILTER (See Fig. 16)  
The fuel filter should be replaced once each season. If fuel  
filter becomes clogged, obstructing fuel flow to carburetor,  
replacement is required.  
Keep finished surfaces and wheels free of all gasoline,  
oil, etc.  
Protect painted surfaces with automotive type wax.  
We do not recommend using a garden hose or pressure  
washer to clean your tractor unless the engine and trans-  
mission are covered to keep water out. Water in engine or  
transmission will shorten the useful life of your tractor. Use  
compressed air or a leaf blower to remove grass, leaves  
and trash from tractor and mower.  
With engine cool, remove filter and plug fuel line sec-  
tions.  
Place new fuel filter in position in fuel line with arrow  
pointing towards carburetor.  
Be sure there are no fuel line leaks and clamps are  
properly positioned.  
Immediately wipe up any spilled gasoline.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUST-  
MENTS:  
Depress brake pedal fully and set parking brake.  
Place attachment clutch in “DISENGAGED” position.  
Turn ignition key to “STOP” and remove key.  
Make sure the blades and all moving parts have completely stopped.  
Disconnectsparkplugwirefromsparkplugandplacewirewhereitcannotcomeincontact  
with plug.  
TO REMOVE MOWER (See Fig. 17)  
TO INSTALL MOWER (See Fig. 17-22)  
Be sure tractor is on level surface and engage parking  
brake.  
Place attachment clutch in “DISENGAGED” position.  
Lower attachment lift lever to its lowest position.  
Remove mower belt from electric clutch pulley (M).  
Lower attachment lift lever to it's lowest position.  
Disconnect front link (E) from mower - remove retainer  
spring and washer.  
CAUTION: Lift lever is spring loaded.  
Have a tight grip on lift lever, lower it  
slowly and engage in lowest position.  
Go to either side of mower and disconnect mower  
suspension arm (A) from chassis and rear lift link (C)  
from rear mower bracket (D) - remove retainer springs  
and washers.  
NOTE: Be sure mower side suspension arms (A) are point-  
ing forward before sliding mower under tractor.  
Go to other side of mower and disconnect the suspen-  
sion arm and rear lift link.  
Slide mower under tractor until it is centered under  
tractor.  
CAUTION: After rear lift links are dis-  
connected, the attachment lift lever  
will be spring loaded. Have a tight grip  
on lift lever when changing position of  
the lever.  
Slide mower out from under right side of tractor.  
B
F
M
A
E
C
D
Fig. 17  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
ATTACH MOWER SIDE SUSPENSION ARMS (A) TO  
ATTACH FRONT LINK (E) - Work from left side of trac-  
CHASSIS - Position hole in arm over pin (B) on outside  
of tractor chassis and secure with washer and retainer  
spring.  
tor. Insert rod end of link assembly through front hole  
in tractor front suspension bracket (F).  
Insert end of link (E) into hole in front mower bracket  
(H) and secure with washer and retainer spring (J).  
Repeat on opposite side of tractor.  
E
A
J
F
B
H
Fig. 18  
Fig. 20  
ATTACH REAR LIFT LINKS (C) - Lift rear corner of  
mower and position slot in link assembly over pin on  
rear mower bracket (D) and secure with washer and  
retainer spring.  
Install belt onto electric clutch pulley (M).  
M
Repeat on opposite side of tractor.  
C
Fig. 21  
IMPORTANT: CHECK BELT FOR PROPER ROUTING  
IN ALL MOWER PULLEY GROOVES.  
D
Raise attachment lift lever to highest position.  
If necessary, adjust gauge wheels before operating  
mower as shown in the Operation section of this  
manual.  
B
Fig. 19  
F
M
A
E
C
D
Fig. 22  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
TO LEVEL MOWER  
If adjustment is necessary, see step in Visual Adjust-  
Make sure tires are properly inflated to the PSI shown on  
tires. If tires are over or under inflated, it may affect the  
appearance of your lawn and lead you to think the mower  
is not adjusted properly.  
ment instructions above.  
Recheck measurements, adjust if necessary until both  
sides are equal.  
FRONT-TO-BACK ADJUSTMENT (See Figs. 25 and 26)  
IMPORTANT: Deck must be level side-to-side.  
VISUAL SIDE-TO-SIDE ADJUSTMENT (See Fig. 23)  
With all tires properly inflated and if your lawn appears  
unevenly cut, determine which side of mower is cutting  
lower.  
To obtain the best cutting results, the mower blades should  
be adjusted so the front tip is 1/8" to 1/2" lower than the  
rear tip when the mower is in its highest position.  
NOTE: As desired, you can raise the low side of mower  
CAUTION: Blades are sharp. Protect  
your hands with gloves and/or wrap  
blade with heavy cloth.  
or lower the high side.  
Go to side of mower you wish to adjust.  
With a 3/4" or adjustable wrench, turn lift link adjust-  
ment nut (A) to the left to lower LH side of mower, or,  
to the right to raise LH side of mower.  
Raise mower to highest position.  
Position any blade so the tip is pointing straight forward.  
Measure distance (B) to the ground at front and rear tip  
of the blade.  
If front tip of blade is not 1/8" to 1/2" lower than the rear  
A
02548  
B
B
Fig. 25  
tip, go to the front of tractor.  
With an 11/16" or adjustable wrench, loosen jam nut A  
several turns to clear adjustment nut B.  
With a 3/4" or adjustable wrench, turn front link adjust-  
ment nut (B) clockwise (ltighten) to raise the front of  
mower, or, counterclockwise (loosen) to lower the front  
mower.  
Turn nut left  
to lower mower  
Turn nut right  
to raise mower  
02948  
Fig. 23  
NOTE: Each full turn of adjustment nut will change mower  
height about 3/16".  
Test your adjustment by mowing some uncut grass  
and visually checking the appearance. Readjust, if  
necessary, until you are satisfied with the results.  
B
A
PRECISION SIDE-TO-SIDE ADJUSTMENT  
(See Fig. 24)  
With all tires properly inflated, park tractor on level  
ground or driveway.  
CAUTION: Blades are sharp. Protect  
your hands with gloves and/or wrap  
blade with heavy cloth.  
Loosen adjust  
Tighten adjust nut  
nut B to lower  
B to raise mower  
mower  
Raise mower to its highest position.  
At both sides of mower, position blade at side and  
measure the distance (A) from bottom edge of blade  
to the ground. The distance should be the same on  
both sides.  
Loosen jam nut A first  
Fig. 26  
NOTE: Each full turn of the adjustment nut will change  
mower height about 1/8".  
02966  
Recheck measurements, adjust if necessary until front  
tip of blade is 1/8" to 1/2" lower than the rear tip.  
Holdadjustmentnutinpositionwithwrenchandtighten  
jam nut securely against adjustment nut.  
A
A
20  
Fig. 24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
Pull belt slack toward rear of tractor. Carefully remove  
TO REPLACE MOWER DRIVE BELT  
(See Fig. 27)  
belt upwards from transmission input pulley and over  
cooling fan blades (F).  
MOWER DRIVE BELT REMOVAL  
Removebeltdownwardfromenginepulleyandaround  
electric clutch (G).  
Slide belt toward rear of tractor, off the steering plate  
(H) and remove from tractor.  
Park tractor on a level surface. Engage parking  
brake.  
Lower attachment lift lever to its lowest position.  
Remove any dirt or grass clippings which may have  
accumulated around mandrels and entire upper deck  
surface.  
BELT INSTALLATION -  
Install new belt from tractor rear to front, over the steer-  
ing plate (H) and above clutch brake pedal shaft (J).  
Pull belt toward front of tractor and roll belt around  
electric clutch and onto engine pulley (G).  
Pullbelttowardrearoftractor. Carefullyworkbeltdown  
around transmission cooling fan and onto the input  
pulley (F). Be sure belt is inside the belt keeper.  
Remove belt from electric clutch pulley (M), both man-  
drel pulleys (R) and all idler pulleys (S).  
MOWER DRIVE BELT INSTALLATION  
Install belt around all mandrel pulleys (R) and around  
idler pulleys (S) as shown.  
Install belt on centerspan idler (E).  
Install belt through stationary idler (C) and clutching  
idler (D).  
Reinstall anti-rotation link (B) on right side of tractor.  
Tighten securely.  
Install belt onto electric clutch pulley (M).  
IMPORTANT: Check belt for proper routing in all mower  
pulley grooves.  
Raise attachment lift lever to highest position.  
Reconnect clutch harness (A).  
Make sure belt is in all pulley grooves and inside all  
belt guides and keepers.  
S
Install mower (See “TO INSTALL MOWER” in this  
section of manual).  
M
R
G
R
H
B
A
Fig. 27  
TO REPLACE MOTION DRIVE BELT  
(See Fig. 28)  
C
J
Park the tractor on level surface. Engage parking brake.  
For assistance, there is a belt installation guide decal on  
bottom side of left footrest.  
D
E
BELT REMOVAL -  
Remove mower (See “TO REMOVE MOWER” in this  
section of manual).  
NOTE: Observe entire motion drive belt and position of all  
belt guides and keepers.  
F
Disconnect clutch wire harness (A).  
Remove anti-rotation link (B) on right side of tractor.  
Remove belt from stationary idler (C) and clutching  
idler (D).  
02953  
electric  
Remove belt from centerspan idler (E).  
Fig. 28  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
TO START ENGINE WITH A WEAK BATTERY  
(See Fig. 30)  
TO CHECK BRAKE  
If tractor requires more than five (5) feet to stop at highest  
speed in highest gear on a level, dry concrete or paved  
surface, then brake must be serviced.  
WARNING: Lead-acid batteries gen-  
erate explosive gases. Keep sparks,  
flameandsmokingmaterialsawayfrom  
batteries. Always wear eye protection  
when around batteries.  
You may also check brake by:  
Park tractor on a level, dry concrete or paved surface,  
depress brake pedal all the way down and engage  
parking brake.  
Disengage transmission by placing freewheel control  
in “transmission disengaged” position. Pull freewheel  
control out and into the slot and release so it is held in  
the disengaged position.  
If your battery is too weak to start the engine, it should be  
recharged. (See "BATTERY" in the MAINTENANCE sec-  
tion of this manual).  
If “jumper cables” are used for emergency starting, follow  
this procedure:  
IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12  
VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12  
VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO  
START OTHER VEHICLES.  
The rear wheels must lock and skid when you try to manu-  
ally push the tractor forward. If the rear wheels rotate,  
then the brake needs to be serviced. Contact a qualified  
service center.  
TO ADJUST STEERING WHEEL ALIGNMENT  
TO ATTACH JUMPER CABLES -  
If steering wheel crossbars are not horizontal (left to right)  
whenwheelsarepositionedstraightforward,removesteer-  
ing wheel and reassemble per instructions in the Assembly  
section of this manual.  
Connect one end of the RED cable to the POSITIVE  
(+) terminal of each battery(A-B), taking care not to  
short against tractor chassis.  
ConnectoneendoftheBLACKcabletotheNEGATIVE  
(-) terminal (C) of fully charged battery.  
Connect the other end of the BLACK cable (D) to good  
chassis ground, away from fuel tank and battery.  
FRONT WHEEL TOE-IN/CAMBER  
Your new tractor front wheel toe-in and camber is set at the  
factory and is normal. The front wheel toe-in and camber  
are not adjustable. If damage has occurred to affect the  
factory set front wheel toe-in or camber, contact a qualified  
service center.  
TO REMOVE CABLES, REVERSE ORDER -  
BLACK cable first from chassis and then from the fully  
charged battery.  
RED cable last from both batteries.  
TO REMOVE WHEEL FOR REPAIRS  
(See Fig. 29)  
Block up axle securely.  
Removeaxlecover,retainingringandwasherstoallow  
wheel removal (rear wheel contains a square key - Do  
not lose).  
Repair tire and reassemble.  
On rear wheels only: align grooves in rear wheel hub  
and axle. Insert square key.  
WEAK OR DEAD  
BATTERY  
FULLY CHARGED  
BATTERY  
Replace washers and snap retaining ring securely in  
axle groove.  
Replace axle cover.  
Fig. 30  
NOTE: To seal tire punctures and prevent flat tires due  
to slow leaks, tire sealant may be purchased from your  
local parts dealer. Tire sealant also prevents tire dry rot  
and corrosion.  
WASHERS  
RETAINING  
RING  
AXLE COVER  
SQUARE KEY (REAR  
WHEEL ONLY)  
Fig. 29  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
TO REMOVE HOOD AND GRILL ASSEMBLY  
(See Fig. 32)  
REPLACING BATTERY (See Fig. 31)  
WARNING: Do not short battery terminals by allowing  
a wrench or any other object to contact both terminals at  
the same time. Before connecting battery, remove metal  
bracelets, wristwatch bands, rings, etc.  
Raise hood.  
Unsnap headlight wire connector.  
Standinfrontoftractor. Grasphoodatsides, tilttoward  
engine and lift off of tractor.  
Positive terminal must be connected first to prevent spark-  
ing from accidental grounding.  
1. Lift hood to raised position.  
To replace, reverse above procedure.  
2. Disconnect BLACK battery cable (A) then RED battery  
cable and carefully remove battery from tractor.  
3. Install new battery with terminals in same position as  
old battery.  
HOOD  
4. FirstconnectREDbatterycable(B)topositive(+)battery  
terminal with hex bolt and keps nut as shown. Tighten  
securely. Slide terminal cover (C) over terminal.  
5. ConnectBLACKgroundingcabletonegative(-)battery  
terminal with remaining hex bolt and keps nut. Tighten  
securely  
HEADLIGHT  
WIRE  
CONNECTOR  
6. Close hood.  
NEGATIVE  
A
(BLACK)  
CABLE  
02141  
C
B
POSITIVE  
(RED)  
CABLE  
Fig. 32  
02954  
ENGINE  
Fig. 31  
TO ADJUST THROTTLE CONTROL CABLE  
The throttle control has been preset at the factory and  
adjustment should not be necessary. If adjustment is nec-  
essary, see engine manual.  
TO REPLACE HEADLIGHT BULB  
Raise hood.  
Pull bulb holder out of the hole in the backside of the  
grill.  
Replace bulb in holder and push bulb holder securely  
back into the hole in the backside of the grill.  
Close hood.  
TO ADJUST CHOKE CONTROL  
The choke control has been preset at the factory and ad-  
justment should not be necessary. If adjustment is neces-  
sary, see engne manual.  
INTERLOCKS AND RELAYS  
Loose or damaged wiring may cause your tractor to run  
poorly, stop running, or prevent it from starting.  
TO ADJUST CARBURETOR  
Check wiring. See electrical wiring diagram in the  
Repair Parts section.  
Your carburetor is not adjustable. If your engine does not  
operate properly due to suspected carburetor problems,  
take your tractor to an authorized service center for repair  
and/or adjustment.  
TO REPLACE FUSE  
Replace with 20 amp automotive-type plug-in fuse. The  
fuse holder is located behind the dash.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STORAGE  
Immediately prepare your tractor for storage at the end  
of the season or if the tractor will not be used for 30 days  
or more.  
ENGINE  
FUEL SYSTEM  
IMPORTANT: ITISIMPORTANTTOPREVENTGUMDEPOSITS  
FROMFORMINGINESSENTIALFUELSYSTEMPARTSSUCH  
AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK  
DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT  
ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING  
ETHANOLORMETHANOL)CANATTRACTMOISTUREWHICH  
LEADSTOSEPARATIONANDFORMATIONOFACIDSDURING  
STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM  
OF AN ENGINE WHILE IN STORAGE.  
WARNING: Neverstorethetractorwith  
gasoline in the tank inside a building  
where fumes may reach an open flame  
orspark. Allowtheenginetocoolbefore  
storing in any enclosure.  
TRACTOR  
Empty the fuel tank by starting the engine and let it run  
until the fuel lines and carburetor are empty.  
Never use engine or carburetor cleaner products in  
the fuel tank or permanent damage may occur.  
Remove mower from tractor for winter storage. When  
mower is to be stored for a period of time, clean it thor-  
oughly, remove all dirt, grease, leaves, etc. Store in a  
clean, dry area.  
Use fresh fuel next season.  
Clean entire tractor (See “CLEANING” in the Mainte-  
nance section of this manual).  
Inspect and replace belts, if necessary (See belt re-  
placement instructions in the Service and Adjustments  
section of this manual).  
NOTE: Fuel stabilizer is an acceptable alternative in mini-  
mizing the formation of fuel gum deposits during storage.  
Add stabilizer to gasoline in fuel tank or storage container.  
Always follow the mix ratio found on stabilizer container.  
Run engine at least 10 minutes after adding stabilizer to  
allow the stabilizer to reach the carburetor. Do not empty  
the gas tank and carburetor if using fuel stabilizer.  
Lubricate as shown in the Maintenance section of this  
manual.  
Be sure that all nuts, bolts and screws are securely  
fastened. Inspect moving parts for damage, breakage  
and wear. Replace if necessary.  
Touch up all rusted or chipped paint surfaces; sand  
lightly before painting.  
ENGINE OIL  
Drain oil (with engine warm) and replace with clean engine  
oil. (See “ENGINE” in the Maintenance section of this  
manual).  
BATTERY  
CYLINDER(S)  
Fully charge the battery for storage.  
Remove spark plug(s).  
After a period of time in storage, battery may require  
recharging.  
Pour one ounce of oil through spark plug hole(s) into  
cylinder(s).  
To help prevent corrosion and power leakage during  
long periods of storage, battery cables should be dis-  
connected and battery cleaned thoroughly (see “TO  
CLEAN BATTERY AND TERMINALS” in the Mainte-  
nance section of this manual).  
Turn ignition key to “START” position for a few seconds  
to distribute oil.  
Replace with new spark plug(s).  
OTHER  
After cleaning, leave cables disconnected and place  
cables where they cannot come in contact with battery  
terminals.  
If battery is removed from tractor for storage, do not  
store battery directly on concrete or damp surfaces.  
Do not store gasoline from one season to another.  
Replace your gasoline can if your can starts to rust.  
Rust and/or dirt in your gasoline will cause problems.  
If possible, store your tractor indoors and cover it to  
give protection from dust and dirt.  
Cover your tractor with a suitable protective cover that  
does not retain moisture. Do not use plastic. Plastic  
cannot breathe which allows condensation to form and  
will cause your tractor to rust.  
IMPORTANT: NEVER COVER TRACTOR WHILE ENGINE  
AND EXHAUST AREAS ARE STILL WARM.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING POINTS  
PROBLEM  
CAUSE  
CORRECTION  
Will not start  
1. Out of fuel.  
1. Fill fuel tank.  
2. Engine not “CHOKED” properly.  
3. Engine flooded.  
4. Bad spark plug.  
5. Weak or dead battery.  
6. Dirty air filter.  
2. See “TO START ENGINE” in Operation section.  
3. Wait several minutes before attempting to start.  
4. Replace spark plug.  
5. Recharge or replace battery.  
6. Clean/replace air filter.  
7. Dirty fuel filter.  
8. Water in fuel.  
7. Replace fuel filter.  
8. Empty fuel tank and carburetor, refill tank with fresh  
gasoline and replace fuel filter.  
9. Loose or damaged wiring.  
10. Carburetor out of adjustment.  
9. Check all wiring.  
10. See To Adjust Carburetor” in Service Adjustments  
section.  
11. Engine valves out of adjustment.  
11. Contact an authorized service center/department.  
Hard to start  
1. Dirty air filter.  
2. Bad spark plug.  
1. Clean/replace air filter.  
2. Replace spark plug.  
3. Weak or dead battery.  
4. Dirty fuel filter.  
5. Stale or dirty fuel.  
6. Loose or damaged wiring.  
7. Carburetor out of adjustment.  
3. Recharge or replace battery.  
4. Replace fuel filter.  
5. Empty fuel tank and refill tank with fresh, clean gasoline.  
6. Check all wiring.  
7. See To Adjust Carburetor” in Service Adjustments  
section.  
8. Engine valves out of adjustment.  
8. Contact an authorized service center/department.  
Engine will not turn over  
1. Brake pedal not depressed.  
2. Attachment clutch is engaged.  
3. Weak or dead battery.  
1. Depress brake pedal.  
2. Disengage attachment clutch.  
3. Recharge or replace battery.  
4. Replace fuse.  
4. Blown fuse.  
5. Corroded battery terminals.  
6. Loose or damaged wiring.  
7. Faulty ignition switch.  
8. Faulty solenoid or starter.  
9. Faulty operator presence switch(es).  
5. Clean battery terminals.  
6. Check all wiring.  
7. Check/replace ignition switch.  
8. Check/replace solenoid or starter.  
9. Contact an authorized service center/department.  
Engine clicks but will not  
start  
1. Weak or dead battery.  
1. Recharge or replace battery.  
2. Clean battery terminals.  
3. Check all wiring.  
2. Corroded battery terminals.  
3. Loose or damaged wiring.  
4. Faulty solenoid or starter.  
4. Check/replace solenoid or starter.  
Loss of power  
1. Cutting too much grass/too fast.  
2. Throttle in “CHOKE” position.  
3. Build-up of grass, leaves and trash under mower.  
4. Dirty air filter.  
1. Raise cutting height/reduce speed.  
2. Adjust throttle control.  
3. Clean underside of mower housing.  
4. Clean/replace air filter.  
5. Low oil level/dirty oil.  
6. Faulty spark plug.  
7. Dirty fuel filter.  
5. Check oil level/change oil.  
6. Clean and regap or change spark plug.  
7. Replace fuel filter.  
8. Stale or dirty fuel.  
9. Water in fuel.  
8. Empty fuel tank and refill tank with fresh, clean gasoline.  
9. Empty fuel tank and carburetor, refill tank with fresh  
gasoline and replace fuel filter.  
10. Spark plug wire loose.  
11. Dirty engine air screen/fins.  
12. Dirty/clogged muffler.  
10. Connect and tighten spark plug wire.  
11. Clean engine air screen/fins.  
12. Clean/replace muffler.  
13. Loose or damaged wiring.  
14. Carburetor out of adjustment.  
13. Check all wiring.  
14. See To Adjust Carburetor” in Service Adjustments  
section.  
15. Engine valves out of adjustment.  
15. Contact an authorized service center/department.  
Excessive vibration  
1. Worn, bent or loose blade.  
2. Bent blade mandrel.  
1. Replace blade. Tighten blade bolt.  
2. Replace blade mandrel.  
3. Loose/damaged part(s).  
3. Tighten loose part(s). Replace damaged parts.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING POINTS  
PROBLEM  
CAUSE  
CORRECTION  
Engine dies when  
tractor is shifted  
into reverse  
1. Reverse operation system  
(ROS) is not "ON" while  
1. Turn ignition key to  
ROS "ON" position.  
mower or other attachment  
is engaged.  
See Operation section.  
Engine continues to run  
when operator leaves seat  
with attachment clutch  
engaged  
1. Faulty operator-safety presence control system.  
1. Check wiring, switches and connections. If not  
corrected, contact an authorized service center/  
department.  
Poor cut - uneven  
1. Worn, bent or loose blade.  
2. Mower deck not level.  
1. Replace blade. Tighten blade bolt.  
2. Level mower deck.  
3. Buildup of grass, leaves, and trash under mower.  
4. Bent blade mandrel.  
5. Clogged mower deck vent holes from buildup of  
grass, leaves, and trash around mandrels.  
3. Clean underside of mower housing.  
4. Replace blade mandrel.  
5. Clean around mandrels to open vent holes.  
Mower blades will not  
rotate  
1. Obstruction in clutch mechanism.  
2. Worn/damaged mower drive belt.  
3. Frozen idler pulley.  
1. Remove obstruction.  
2. Replace mower drive belt.  
3. Replace idler pulley.  
4. Frozen blade mandrel.  
4. Replace blade mandrel.  
Poor grass discharge  
1. Engine speed too slow.  
2. Travel speed too fast.  
1. Place throttle control in “FAST” position.  
2. Shift to slower speed.  
3. Wet grass.  
4. Mower deck not level.  
3. Allow grass to dry before mowing.  
4. Level mower deck.  
5. Low/uneven tire air pressure.  
6. Worn, bent or loose blade.  
7. Buildup of grass, leaves and trash under mower.  
8. Mower drive belt worn.  
9. Blades improperly installed.  
10. Improper blades used.  
5. Check tires for proper air pressure.  
6. Replace blade. Tighten blade bolt.  
7. Clean underside of mower housing.  
8. Replace mower drive belt.  
9. Reinstall blades sharp edge down.  
10. Replace with blades listed in this manual.  
11. Clean around mandrels to open vent holes.  
11. Clogged mower deck vent holes from buildup of  
grass, leaves, and trash around mandrels.  
Headlight(s) not working  
(if so equipped)  
1. Light switch is “OFF”.  
2. Bulb(s) or lamp(s) burned out.  
3. Faulty light switch.  
4. Loose or damaged wiring.  
5. Blown fuse.  
1. Turn light switch “ON”.  
2. Replace bulb(s) or lamp(s).  
3. Check/replace light switch.  
4. Check wiring and connections.  
5. Replace fuse.  
Battery will not charge  
Loss of drive  
1. Bad battery cell(s).  
1. Replace battery.  
2. Poor cable connections.  
3. Faulty regulator (if so equipped).  
4. Faulty alternator.  
2. Check/clean all connections.  
3. Replace regulator.  
4. Replace alternator.  
1. Freewheel control in “disengaged” position.  
2. Motion drive belt worn, damaged, or broken.  
3. Air trapped in transmission during shipment  
or servicing.  
1. Place freewheel control in “engaged” position.  
2. Replace motion drive belt.  
3. Purge transmission.  
Engine “backfires” when  
turning engine “OFF”  
1. Engine throttle control not set between half and  
full speed (fast) position before stopping engine.  
1. Move throttle control between half and full speed  
(fast) position before stopping engine.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Jonsered Motor AB,  
S-433 81 Partille, Sweden.  
532 41 94-10 Rev. 1 06.23.08 SBW  
Printed in U.S.A.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

American Lawn Mower Co Lawn Mower UT13120 User Manual
Black Decker Lawn Mower CMM1200 User Manual
Garmin Lawn Mower 12 User Guide
Poulan Lawn Mower 175581 User Guide
Poulan Lawn Mower 186890 User Guide
Sears Lawn Mower 6 3041 User Manual
Snapper Lawn Mower 1690031 User Manual
Snapper Lawn Mower E331416KVE User Manual
Snapper Lawn Mower PC21507BV User Manual
Weed Eater Lawn Mower WELRVBA30 User Guide