For Serial Nos.
510,000 & Higher
Part No. 103-8614 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
POTENTIAL HAZARD
♦ This product is a piece of power equipment.
WHAT CAN HAPPEN
♦ Failure to follow safe operating practices can result in serious
operator injury or even death.
HOW TO AVOID THE HAZARD
♦ Keep all shields, guards, and safety devices (especially the grass
discharge system) in place and in proper working condition.
♦ Stop engine and wait for all moving parts to stop. Remove spark
plug wire(s) or remove key before adjusting, servicing, or
performing maintenance.
♦ If mower deck becomes clogged, stop engine and wait for all
moving parts to stop. Remove spark plug wire(s) or remove key
before cleaning blockage.
♦ Keep hands, feet, and clothing away from power driven parts.
♦ Keep off mower unless seat platform is provided.
♦ Keep others off mower.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
CONGRATULATIONS on the purchase of your Exmark Navigator Cutting Deck.
This product has been carefully designed and manufactured to give you a maximum
amount of dependability and years of trouble-free operation.
OPERATOR'S MANUAL
This manual contains assembly, operating, maintenance, adjustment, and safety
instructions for your Navigator Cutting Deck.
BEFORE OPERATING YOUR MOWER,
CAREFULLY READ THIS MANUAL IN ITS ENTIRETY.
By following the operating, maintenance, and safety instructions, you will prolong
the life of your equipment, maintain its maximum efficiency, and promote safe
operation.
If additional information is needed, or should you require trained mechanic
service, contact your authorized Exmark equipment dealer or distributor.
All Exmark equipment dealers and distributors are kept informed of the latest
methods of servicing and are equipped to provide prompt and efficient service in the
field or at their service stations. They carry ample stock of service parts or can
secure them promptly for you from the factory.
All Exmark parts are thoroughly tested and inspected before leaving the factory,
however, attention is required on your part if you are to obtain the fullest measure of
satisfaction and performance.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
1. SAFETY
PAGE
1.1 Safety Alert Symbol....................................................................................... 1
1.2 Training ......................................................................................................... 1
1.3 Preparation................................................................................................. 1-2
1.4 Operation ...................................................................................................... 2
1.5 Maintenance & Storage................................................................................. 2
1.6 Safety Signs............................................................................................... 2-3
2. SPECIFICATIONS
2.1 Model Number............................................................................................... 4
2.2 Dimensions.................................................................................................... 4
2.3 Torque Requirements.................................................................................... 4
3. ASSEMBLY INSTRUCTIONS
3.1 Uncrate Deck................................................................................................. 4
3.2 Assemble Discharge Chute ........................................................................... 4
3.3 Assemble Deck to Navigator ...................................................................... 4-6
3.4 Deck Removal............................................................................................... 6
4. MAINTENANCE & ADJUSTMENTS
4.1 Deck Raising and Lowering........................................................................ 6-8
4.2 Maintenance............................................................................................. 8-11
4.3 Adjustments ........................................................................................... 11-12
5. PARTS LIST
5.1 Deck Group............................................................................................ 13-14
5.2 Front Frame Group................................................................................. 15-16
5.3 Gearbox Components ................................................................................ 17
6. WARRANTY.......................................................................................................... 18
v
Download from Www.Somanuals.com. All Manuals Search And Download.
1. SAFETY
1.1 SAFETY ALERT SYMBOL
This SAFETY ALERT SYMBOL
is used both in this manual and on the unit to identify
important safety messages which must be followed to avoid accidents. This symbol means:
ATTENTION! BECOME ALERT!
YOUR SAFETY IS INVOLVED!
The safety alert symbol appears above information which alerts you to unsafe actions or
situations and will be followed by the word DANGER, WARNING, or CAUTION.
DANGER: White lettering / Red background. Indicates an imminently hazardous situation
which, if not avoided, WILL result in death or serious injury.
WARNING: Black lettering / Orange background. Indicates a potentially hazardous situation
which, if not avoided, COULD result in death or serious injury.
CAUTION: Black lettering / Yellow background. Indicates a potentially hazardous situation
which, if not avoided, MAY result in minor or moderate injury.
1.2 TRAINING
1.2.1
Regard the Exmark mower as a piece of power equipment and teach this regard to all
who operate this unit.
1.2.2
Before operating your mower, read the Navigator tractor and cutting deck manual
instructions carefully. Familiarize yourself with the controls and the proper use of the
equipment. If the operator(s) or mechanic(s) can not read English, it is the owner’s
responsibility to explain this material to them.
1.2.3
1.2.4
Do not allow operation of this machine by untrained personnel. Never allow children,
teenagers, or people unfamiliar with these instructions to use the mower. Local
regulations may restrict the age of the operator.
Avoid mowing while people, especially children, or pets, are nearby. Keep in mind
that the operator or user is responsible for accidents or hazards occurring to other
people or their property.
1.3 PREPARATION
1.3.1
Do not modify the Navigator cutting deck and only use on approved Exmark
machines.
1.3.2
The use of personal protective equipment, such as (but not limited to) protection for
the eyes, ears, feet, and head is recommended.
CAUTION
POTENTIAL HAZARD
♦ This machine produces sound levels in excess of 85
dBA at the operator’s ear when in operation.
WHAT CAN HAPPEN
♦ Exposure to sound levels of 85 dBA or above for
extended periods of time can cause hearing loss.
HOW TO AVOID THE HAZARD
♦ Wear hearing protection when operating this
machine.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
1.3.3
1.3.4
While mowing, always wear substantial footwear and long trousers. Do not operate
equipment when barefoot or when wearing open sandals.
Thoroughly inspect the area where the equipment is to be used and remove all
stones, sticks, wires, bones, and other foreign objects which may damage the
equipment or cause personal injury to the operator or bystanders.
1.4 OPERATION
Although hazard control and accident prevention are partially dependent upon the
design and configuration of the equipment, these factors are also dependent upon the
awareness, concern, prudence, and proper training of the personnel involved in the
operation, transport, maintenance, and storage of the equipment. It is essential that all
Operator Safety Mechanisms be connected and in operating condition prior to use for
mowing.
WARNING
POTENTIAL HAZARD
♦ Hands, feet, hair, clothing, or accessories can become
entangled in rotating parts.
WHAT CAN HAPPEN
♦ Contact with rotating parts can cause traumatic amputation
or severe lacerations.
HOW TO AVOID THE HAZARD
♦ Do not operate the machine without guards, shields, and
safety devices in place and working.
♦ Keep hands, feet, hair, jewelry, or clothing away from
rotating parts.
1.4.1
1.4.2
Give complete, undivided attention to the job at hand.
Mow only in daylight or good artificial light, keeping away from holes and hidden
hazards. NEVER carry passengers.
1.4.3
1.4.4
Use EXTREME caution when backing up. LOOK BEHIND YOU!
Stop the blades when crossing surfaces other than grass and when transporting the
mower to and from the area to be mowed.
1.4.5
Never operate the mower with damaged guards, shields, or covers. Always have
safety shields, guards, switches, and other devices in place and in proper working
condition.
1.5 MAINTENANCE AND STORAGE
1.5.1
1.5.2
1.5.3
1.5.4
Check all bolts frequently to maintain proper tightness.
Keep all guards, shields, and all safety devices in place and in safe working condition.
Frequently check for worn or deteriorating components that could create a hazard.
All replacement parts must be the same as or equivalent to the parts supplied as
original equipment.
1.6 SAFETY SIGNS
1.6.1
Keep all safety signs legible. Remove all grease, dirt and debris from safety signs and
instructional labels.
1.6.2
1.6.3
Safety signs must be replaced if they are missing or illegible.
When new components are installed, be sure that current safety signs are affixed to
the replaced components.
1.6.4
New safety signs may be obtained from Exmark Mfg. Co. Inc.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
1.6.5
1.6.6
Safety signs may be affixed by peeling off the backing to expose the adhesive surface.
Apply only to a clean, dry surface. Smooth to remove any air bubbles.
Familiarize yourself with the following safety signs and instruction labels. They are
critical to the safe operation of your Exmark commercial mower.
PART NO. 103-8797
LOCATION: On Top RH and LH Sides of
Front Frame
PART NO. 68-8340
LOCATION: On Top of Deck LH & RH Sides
PART NO. 98-5954
LOCATION: - On Top of Deck, Under Gear Box Cover
- On LH Frame, Under PTO Shield
- On RH Lower Frame, behind fuel tank
PART NO. 1-403005
PART NO. 103-8798
LOCATION: Front RH Surface of Front Frame
LOCATION: On Top of Mower Deck
LH & RH Sides
PART NO. 103-8425
LOCATION: -On Driveshaft
PART NO. 103-6230
LOCATION: On Top of Deck,
Centered on Each Side
PART NO. 103-8799
LOCATION: On Top of Front Frame, Near Deck
Springs
3
Download from Www.Somanuals.com. All Manuals Search And Download.
2. SPECIFICATIONS
2.1 MODEL NUMBER: CD42CD; CD48CD
2.2 DIMENSIONS
42” Deck
48” Deck
Overall Width
Overall Height
Overall Length
Weight
43.2” (109.7 cm)
13.1” (33.3 cm)
37.2” (94.4 cm)
295 lbs. (134 kg)
49.2” (125.0 cm)
13.1 (33.3 cm)
39.9” (101.3 cm)
325 lbs. (147 kg)
2.3 TORQUE REQUIREMENTS
Bolt Location
Torque
Blade Mounting Bolt.....................................................85-110 ft-lbs. (115-149 N-m)
Gearbox Mounting Bolts ....................................................30-35 ft-lbs. (41-47 N-m)
Gearbox Assembly Bolts....................................................50-55 ft-lbs. (68-75 N-m)
3. ASSEMBLY INSTRUCTIONS
3.1 UNCRATE DECK
a)
Remove flat hairpins from under front frame and discard. See Figure 1.
3.2 ASSEMBLE DISCHARGE CHUTE
a)
b)
c)
Locate the 3 holes at the rear of the mower deck shown in Figure 1 and remove the 3
#10-24 x 3/4 truss head screws and 3 #10-24 nyloc nuts.
Assemble the discharge tube to the mower deck as shown using the hardware removed in
3.2.1., with hinge positioned on top of mower deck.
Locate the discharge tube spring on the mower deck and hook onto the discharge tube
spring bracket. See Figure 1.
FIGURE 1
DISCHARGE TUBE ASSEMBLY
3.3 ASSEMBLE DECK TO NAVIGATOR
a)
b)
Stop engine, wait for all moving parts to stop and remove key.
Roll the mower deck up to the Navigator tractor with the discharge tube down, making sure
the deck springs are located above the drive wheel and below the console on each side.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
c)
Raise seat and install drive shaft onto jackshaft (See Figure 2).
FIGURE 2
JACKSHAFT AND DRIVE SHAFT CONNECTION
d)
Align deck push arm tubes to tractor push arms and push deck rearward. Secure push
arms with lynch pins on left and right sides of the unit. See Figure 3.
FIGURE 3
PUSH ARM INSTALLATION
e)
Align upper portion of the PTO rubber guard to the tabs on the front of the console and
secure with a clevis pin and hairpin on each side. See Figure 4.
FIGURE 4
PTO GUARD INSTALLATION
f)
Release the deck locking pins on each side, raise mower deck to the service position and
secure deck latch onto hook. See section 4.1.1, Raising the Deck to the Service Position.
g)
Install springs onto the spring anchor pins under the left and right consoles and secure with
a washer and hairpin. See Figure 5.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 5
DECK SPRING INSTALLATION
h)
Un-latch deck from raised position, slowly lower deck to ground and lock deck locking pins
on each side per section 4.1.2, Lowering the Deck to the Operation Position.
3.4 DECK REMOVAL
a)
b)
Stop engine, wait for all moving parts to stop, and remove key.
Raise mower deck up and latch with deck locking pins per section 4.1.1, Raising the
Mower Deck to the Service Position.
c)
Remove hairpins and washers at the top of the deck lift assist spring on each side of the
unit. See Figure 5.
d)
e)
Remove the spring from the spring anchor. Repeat for other side of unit.
Un-latch deck from raised position and slowly lower deck to ground per section 4.1.2,
Lowering the Mower Deck to the Operation Position.
NOTE: Deck will become heavier once springs are removed from the anchors. Lower
deck carefully.
f)
Remove lynch pins at front of push arms on both sides of the unit. See Figure 3.
Remove hairpin and clevis from both sides of the PTO guard. See Figure 4.
Raise seat and disconnect drive shaft using quick coupler at jackshaft. See Figure 2.
Pull mower deck forward to remove from unit.
g)
h)
i)
4. MAINTENANCE & ADJUSTMENTS
WARNING
POTENTIAL HAZARD
♦ While maintenance or adjustments are being made,
someone could start the engine.
WHAT CAN HAPPEN
♦ Accidental starting of the engine could seriously injure
you or other bystanders.
HOW TO AVOID THE HAZARD
♦ Remove the key from the ignition switch and pull the
wire(s) off the spark plug(s) before you do any
maintenance. Also push the wire(s) aside so it does
not accidentally contact the spark plug(s).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
4.1DECK RAISING AND LOWERING
4.1.1 Raising the Mower Deck into Service Position:
a) Stop engine, wait for all moving parts to stop and remove key.
WARNING
POTENTIAL HAZARD
♦ Incorrectly raising or lowering a mower deck can be
dangerous.
WHAT CAN HAPPEN
♦ A dropped mower deck can result in a serious injury or
property damage.
HOW TO AVOID THE HAZARD
♦ Always raise and lower deck on flat, dry ground, free
of any obstructions.
♦ Firmly grasp the deck lift handle and lower in a slow
controlled manner.
♦ Always make sure the deck is securely latched in the
“up” or “down” position.
b)
Release the deck locking pins on each side. See Figure 6.
FIGURE 6
RAISING THE DECK
c)
Using deck lift handle, lift deck up and latch in “up” position (latch is located at
front center of seat). See Figure 6.
WARNING
POTENTIAL HAZARD
♦ Operating the mower deck in the raised service
position can be dangerous.
WHAT CAN HAPPEN
♦ Engaging the PTO with a deck in the raised position
can result in a serious injury or property damage.
HOW TO AVOID THE HAZARD
♦ Always lower and lock mower deck in the operation
position before engaging the PTO.
4.1.2
Lowering the Mower Deck to the Operation Position:
a)
While firmly holding onto deck lift handle, unhook deck latch from tractor section
and slowly lower deck to ground.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
b)
Push deck locking pins inward and rotate forward to securely lock deck in
lowered position. See Figure 6.
WARNING
POTENTIAL HAZARD
♦ Operating mower without locking pins securely latched
can result in the mower deck folding up unexpectedly.
WHAT CAN HAPPEN
♦ The mower deck folding up unexpectedly can cause
serious injury.
HOW TO AVOID THE HAZARD
♦ Always operate mower with locking pins securely
latched.
4.2 PERIODIC MAINTENANCE
4.2.1 Clean grass build-up under deck.
Service Interval: Daily
a) Stop engine, wait for all moving parts to stop, and remove key.
b) Raise mower deck and secure in latched position. See section 4.1.1, Raising
the Mower Deck to the Service Position.
c) Clean out any grass build-up from underside of deck and in discharge chute.
d) Lower deck to cutting position and lock deck locking pins. See section 4.1.2,
Lowering the Mower Deck to the Operation Position.
4.2.2 Check mower blades.
Service Interval: Daily
a) Stop engine, wait for all moving parts to stop, and remove key.
b) Lift deck and secure in raised position as stated in Section 4.1.1, Raising the
Mower Deck to the Service Position.
c) Inspect blades and sharpen or replace as required.
d) To remove blade, use a block of wood or locking pliers to hold blade in place and
remove the 1/2-20 x 2 1/4 blade bolt that secures the blade and blade driver.
e) If blade is worn or damaged, remove the shear pins that secure the blade driver
to the blade. Re-install a new blade to the blade driver and secure with the
shear pins.
f)
Re-install the blade driver (with new blades) by using a block of wood or locking
pliers to hold the blade in place and torque the blade bolts to 85-110 ft-lbs. (115-
149 N-m).
NOTE: Blade driver flats must be aligned with the flats on the shaft when
installing blade on the mower deck.
g) Lower the mower deck to the operation position. See section 4.1.2, Lowering
the Mower Deck to the Operation Position.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION
POTENTIAL HAZARD
♦ Operating a mower deck with loose or weakened blade
bolts can be dangerous.
WHAT CAN HAPPEN
♦ A loose or weakened blade bolt could allow a blade
rotating at a high speed to come out from under the deck,
causing serious injury or property damage.
HOW TO AVOID THE HAZARD
♦ Replace the blade bolt after striking a foreign object.
Use only the following replacement parts:
Blade bolt – 92-5816
Washer – 86-1990
♦ DO NOT lubricate the threads of the bolt or spindle before
assembly.
♦ Torque the blade bolt to 85-110 ft. lbs. (115-149 N-m)
FIGURE 7
BLADE BOLT INSTALLATION
4.2.3 Check for loose hardware:
Service Interval: Daily
a) Stop engine, wait for all moving parts to stop, and remove key.
b) Visually inspect machine for any loose hardware or any other possible
4.2.4 Check tire pressures:
The front caster tires are semi-pneumatic and do not need to be inflated.
NOTE: Do not add any type of tire liner or foam fill material to the tires.
Excessive loads created by foam filled tires may cause failures to the hydro drive
system, frame, and other components. Foam filling tires will void the warranty.
4.2.5 Lubricate grease fittings:
Service Interval: Refer to chart.
a) Stop engine, wait for all moving parts to stop, and remove key.
b) Lubricate fittings with one to two pumps of NGLI grade #2 multi-purpose gun
grease.
Refer to the following chart for fitting locations and lubrication schedule.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
GREASE FITTING LUBRICATION CHART
FITTING
LOCATIONS
INITIAL
PUMPS
NO. of
PLACES
SERVICE
INTERVAL
1. Drive Shaft
1
1
3
2
40 hours
8 hours
2. Front Caster Wheel Hub
3. Deck Flip-Up
1
1
*0
4
2
3
100 hours
100 hours
*yearly
4. Push Arm Tubes
5. Caster Pivots
∗
See Section 4.2.5 c) for special lubrication instructions on
the front caster pivots and Section 5.2.6 for special
lubrication instructions on the rear caster wheel hub.
c) Lubricate caster pivots once a year. Remove hex plug
and cap. Thread grease zerk in hole and pump with
grease until it oozes out around top bearing. Remove
grease zerk and thread plug back in. Place cap back on.
4.2.6
Lubricate caster wheel hub:
Service Interval: Once Yearly
a)
Stop engine, wait for all moving parts to stop,
and remove key.
b)
c)
d)
Remove caster wheel from caster forks.
Remove seal guards from the wheel hub.
Remove one of the spacer nuts from the
axle assembly in the caster wheel. Note
that thread locking adhesive has been
applied to lock the spacer nuts to the axle.
Remove the axle (with the other spacer
nut still assembled to it) from the wheel
assembly.
FIGURE 8
CASTER WHEEL ASSEMBLY
Pry out seals, and inspect bearings for wear or
damage and replace if necessary.
e)
f)
Pack the bearings with a NGLI grade #1 multi-purpose grease.
Insert (1) bearing, (1) new seal into the wheel.
g)
NOTE: Seals (Exmark PN 103-0063) must be replaced.
h)
If the axle assembly has had both spacer nuts removed (or broken loose), apply
a thread locking adhesive to (1) spacer nut and thread onto the axle with the
wrench flats facing outward. Do not thread spacer nut all of the way onto the
end of the axle. Leave approximately 1/8” (3 mm) from the outer surface of the
spacer nut to the end of the axle inside the nut.
i)
j)
Insert the assembled nut and axle into the wheel on the side of the wheel with
the new seal and bearing.
With the open end of the wheel facing up, fill the area inside the wheel around
the axle full of NGLI grade #1 multi-purpose grease.
k)
l)
Insert the second bearing and new seal into the wheel.
Apply a thread locking adhesive to the 2nd spacer nut and thread onto the axle
with the wrench flats facing outward.
m) Torque the nut to 75-80 in-lbs. (8-9 N-m), loosen, then re-torque to 20-25 in-lbs.
(2-3 N-m). Make sure axle does not extend beyond either nut.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
n)
c)
Re-install the seal guards over the wheel hub and insert wheel into caster fork.
Re-install caster bolt and tighten nut fully.
IMPORTANT: To prevent seal and bearing damage, check the bearing
adjustment often. Spin the caster tire. The tire should not spin freely (more
than 1 or 2 revolutions) or have any side play. If the wheel spins freely, adjust
torque on spacer nut until there is a slight amount of drag. Re-apply thread
locking adhesive.
Lubricate switch actuator rod with spray type lubricant or light oil.
4.2.7 Change gearbox oil:
Change oil in all 3 gearbox housings after first 50 hrs of operation. Check
every 100 hours thereafter. Add oil as needed until level with oil drain plug.
a)
b)
c)
Stop engine, wait for all moving parts to stop, and remove key.
Place unit on a level surface.
Remove the gearbox and drive shaft assembly from the mower deck. Retain
hardware for re-use.
d)
e)
Remove the large oil drain plug on the front of each of the 3 gearboxes and drain
oil. See Figure 9.
Remove small magnetic plugs and wipe away any material accumulated on the
plugs. See Figure 9.
FIGURE 9
GEARBOX OIL DRAIN LOCATIONS
f)
Apply a Teflon pipe sealant to all small magnetic plugs and re-install into the
gearbox.
g)
h)
Re-install the gearbox and drive shaft assembly to the mower deck.
Fill gearbox with Mobil 1 75W-90 gear lube oil until level with oil drain plug.
NOTE: Mower deck should remain level to the ground when filling gearbox with oil.
Do not fill gearbox with deck raised in the service position.
i)
Apply a Teflon pipe sealant to the 3 large oil plugs and re-install into the gearbox.
4.2.8 Thread locking adhesives such as “Loctite 242” or “Fel-Pro, Pro-Lock Nut Type” are
used on the following fasteners:
a)
Caster wheel spacer nuts.
4.3 ADJUSTMENTS
IMPORTANT: Disengage PTO, shut off engine, wait for all moving parts to stop, and
remove key before servicing, cleaning, or making any adjustments to the unit.
4.3.1 Cutting Height Adjustment:
a)
b)
Stop engine, wait for all moving parts to stop, and remove key.
Move cotter pins on four deck support pins to proper hole for height of cut
desired.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
4.3.2 Deck Leveling:
a) Position mower on a flat surface.
b) Stop engine, wait for all moving parts to stop, and remove key.
c) Inflate drive tires to 15 psi (103 kPa).
d) Verify all hairpins are in the 3” deck height holes with the spacers under the hair
pins. See Figure 10.
e) Shorten/lengthen each deck support pin to obtain blade tip height of 3.0” at the
front of the deck and 3.25” at the rear of the deck.
FIGURE 10
DECK SUPPORT PIN ASSEMBLY
4.3.3 Caster pivot bearings pre-load adjustment:
a) Remove dust cap from caster and tighten nyloc
nut until washers are flat. Back the nyloc off 1/4
of a turn to properly set the pre-load on the
bearings.
Note: If disassembled, make sure the spring
washers are reinstalled as shown in Figure 11.
FIGURE 11
CASTER ADJUSTMENT
4.3.4
Deck Locking pin stop adjustment:
a) Slide deck locking pins in on both sides and
rotate to lock the deck in the “operation” position.
b) Loosen the jam nut and turn the stop screw clockwise until the locking pins is
tight and cannot be rotated by hand. See Figure 12.
c) Loosen the stop screw counter clockwise 1/2 turn and tighten the jam nut.
d) Test the locking pin to make sure it slides freely. Readjust if necessary.
FIGURE 12
DECK LOCKING PIN ADJUSTMENT
12
Download from Www.Somanuals.com. All Manuals Search And Download.
5. PARTS LIST
5.1 DECK GROUP
Item Part No.
Description
Qty.
Item Part No.
Description
Qty.
1
2
3
4
5
6
7
8
9
1-403005
1-413425
1-513690
1-523420
1-613204
1-803075
1-806003
30-8770
Danger, Decal........................................2
Spacer, Deck Support............................4
Clip, Deck Holdup Rod...........................1
Bumper..................................................2
Balljoint..................................................2
Screw, Truss Head #10-24 x 3/4............14
Hairpin, Cotter........................................2
Washer..................................................2
Key, Machine 1/4 x 1/4 x 1 1/2...............1
Decal, Blade Bolt Torque .......................2
Bolt, Blade 1/2-20 x 2 1/4.......................2
Decal, Danger........................................2
Bolt, Shear 1/4-20 x 7/8 .........................4
Pin, Clevis 5/16 x 1 ................................2
Asm, Discharge Tube ............................1
Asm, Front Deck Height Adj...................2
39 322-5
40 323-11
323-8
Screw, HH 5/16-18 x 1........................... 3
Screw, HH 3/8-16 x 2 1/4 (42”) .............. 2
Screw, HH 3/8-16 x 1 1/2 (48”) .............. 2
Screw, HH 3/8-16 x 1 1/4....................... 4
Screw, HH 3/8-16 x 1 3/4....................... 1
Screw, HH 1/2-13 x 3 1/2....................... 2
Nut, Hex 3/8-24...................................... 3
Setscrew, 3/8-16 x 3/8........................... 1
Washer, #10 Std.................................... 9
Screw, HH Machine 10-24 x 5/8............. 1
Nut, Whizlock 3/8-16 ............................. 6
Nut, Nyloc #10-24.................................. 15
Nut, Nyloc 5/16-18................................. 3
Nut, Nyloc 3/8-16................................... 1
Nut, Nyloc 3/8-24................................... 1
Nut, Whizlock 5/16-18 ........................... 4
Nut, Whizlock 1/2-13 ............................. 2
Rivet ...................................................... 5
Decal, Commercial (42")........................ 1
Decal, Commercial (48")........................ 1
Spacer (42") .......................................... 2
Spacer (48") .......................................... 2
Gearbox,(42") Std.................................. 1
Gearbox,48 Std...................................... 1
Asm, Deck W/Decals (42") .................... 1
41 323-7
42 323-9
43 325-14
44 3219-3
45V 3247-2
46 3256-14
47 3290-134
48 3290-357
49 3296-2
50 3296-29
51 3296-39
52 3296-6
53 32128-20
54 32128-49
55 114439
56 103-9024
1-403131
67-7490
10 68-8340
11 92-5816
12 98-5954
13 99-0283
14 1-808280
15 103-9487
16 109-0321
17 103-3698-03 Guard, Plenum.......................................1
18 103-3700
19ꢀ 109-0322
109-0323
Roller, Deck ...........................................2
Asm, Rear Deck Height Adj. (42”)..........2
Asm, Rear Deck Height Adj. (48”)..........2
Asm, Drive Shaft W/Decal .....................1
Asm, Cross "U" Joint .............................2
Yoke, Keyed ..........................................1
Yoke, Quick Disconnect.........................1
Spacer, Roller........................................2
Hinge .....................................................1
20 103-9485
103-9327
57 106-5620
106-5597
103-9328
58 103-3460
103-3387
103-9329
21 103-4230
22 103-4974
59O 103-9479
103-9478
Asm, Deck W/Decals (48")
1
O
23 103-5868-01 Wld, Spring Mount .................................1
24 103-5979 Guard, PTO ...........................................1
25 103-6183-03 Bracket, PTO Guard ..............................1
26 103-6230 Decal, Cutting Height Adjustment ..........2
27 103-6290-03 Plate, Drive Line Cover ..........................1
60 103-4209
103-4207
Blade, LH (42") Black ............................ 1
Blade, LH (48") Black ............................ 1
Blade, RH (42") Red .............................. 1
Blade, RH (48") Red .............................. 1
Asm, Gearbox Cover W/Decal (42") ...... 1
Asm, Gearbox Cover W/Decal (48") ...... 1
61 103-4210
103-4208
62P 103-9497
28 103-7353
29 103-7705
30 103-7994
31 103-8307
32Q 103-8363
33 103-8425
34 103-8496
35 103-8610
36 103-8841
37 321-2
Hairpin, Cut Height.................................4
Driver, Blade..........................................2
Balljoint..................................................1
Latch, Deck............................................1
Asm, Deck Latch....................................1
Decal, Driveline......................................1
Nut, Jam 7/8-9 .......................................2
Stand-Off, 1/2 Hex .................................2
Spring ....................................................1
Screw, HH 1/4-20 x 1/2..........................2
Screw, HH 5/16-18 x 3/4........................7
103-9496
P
63 103-8556-01 Wld, Baffle Discharge LH (42").............. 1
103-8590-01 Wld, Baffle Discharge LH (48").............. 1
64 103-8557-01 Wld, Baffle Discharge RH (42") ............. 1
103-8591-01 Wld, Baffle Discharge RH (48") ............. 1
65 103-8626
103-8629
Pad, Anti Skid (42") ............................... 1
Pad, Anti Skid (48") ............................... 1
Pad, Anti Skid (42") ............................... 1
Pad, Anti Skid (48") ............................... 1
Nut, Nyloc 1/4-20................................... 4
Washer, 5/16 SAE................................. 3
66 103-8667
103-8630
67 3296-42
68 3256-23
38 322-3
Exmark red touch up paint (spray paint - P/N 1-850337 - .6 oz liquid bottle - P/N 103-9140).
V
O
P
Q
Use Pro-Lock, Nut Type (P/N 1-840022, .5ml tube) on setscrew, item #45.
Deck assembly includes anti skid pad, item #66.
Gearbox cover assembly includes anti skid pad, item #62.
Deck latch assembly includes nyloc nut, item #52.
ꢀ
Rear deck height adj. assembly includes (1) whizlock nut. Item #48.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
5.1 DECK GROUP
14
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2 FRONT FRAME GROUP
Item Part No.
Description
Qty.
Item Part No.
Description
Qty.
1
2
3
4
5
6
7
1-303334
1-513810
1-543508
1-543509
1-543511
1-633508
1-811010
Washer, Spring Disk 5/16 ......................2
Bushing, Flanged...................................4
Cup, Bearing Tapered Roller .................4
Cone, Bearing Tapered Roller................4
Seal, Grease..........................................2
Washer, Spring Disk..............................6
Plug .......................................................2
27 103-8797
28 103-8798
29 103-8799
30 302-19
31 302-61
32 322-4
Decal, Folding Deck............................... 2
Decal, Danger........................................ 1
Decal, Spring......................................... 2
Zerk, 1/4-28 Str...................................... 4
Zerk, 45° 1/4-28..................................... 4
Screw, HH 5/16-18 x 7/8........................ 2
Screw, HH 1/2-13 x 4 3/4....................... 2
Nut, Jam 3/8-16..................................... 2
Setscrew, SQH 3/8-16 x 1 ..................... 2
Washer, 3/4 SAE................................... 2
Nut, Nyloc 5/16-18................................. 2
Nut, Nyloc 3/8-16................................... 4
Nut, Nyloc 1/2-13................................... 2
Nut, Nyloc 3/4-10................................... 2
Ring, Retaining...................................... 2
Rollpin 3/16 x 3/4................................... 2
Screw, Shoulder 3/8-16 x 1.295............. 2
33 325-38
34 3218-3
35 3243-5
36 3256-28
37 3296-29
38 3296-39
39 3296-45
40 3296-51
41 32120-33
42 32121-3
43 614672
8Q 103-3729-01 Wld, Deck Pivot (RH).............................1
9Q 103-3732-01 Wld, Deck Pivot (LH) .............................1
10 103-3772
11 103-3773
12 103-4017
13 103-4118
14 103-4119
15 103-9482
16 103-4284
17 103-4285
18 103-4588
19 103-4882
20 103-7353
21 103-7436
22 103-7448
23 103-7865
24 103-7971
25 103-8504
26 103-8667
103-8630
Plug, Spring Adjuster .............................2
Shaft, Spring Adjustment .......................2
Spacer, Front Caster..............................2
Wld, Deck Lock (LH)..............................1
Wld, Deck Lock (RH) .............................1
Asm, Deck Lift Handle W/Decal.............1
Wld, Spring Tensioner ...........................2
Mount, Deck Lift Spring..........................2
Bearing, Roller Straight..........................2
Cap, Grease ..........................................2
Pin, Cut Height.......................................2
Bushing, Deck Support ..........................2
E-Ring....................................................2
Wld, Spring Tube...................................2
Cover, Deck Spring................................2
Decal, Navigator Model..........................1
Pad, Anti Skid (42”)................................1
Pad, Anti Skid (48”)................................1
44 103-3655-01 Wld, Fork & Spindle............................... 2
45 103-4324
Asm, Wheel & Tire 8x3.00-4 Sp............. 2
Asm, Front Frame W/Decals (42")......... 1
Asm, Front Frame W/Decals (48")......... 1
Spring, Extension................................... 2
Asm, Caster Wheel W/Axle ................... 1
Asm, Spring Lift Assist........................... 2
46V 103-9481
103-9480
V
47 103-4281
48 103-9495
49O 103-4280
Exmark red touch up paint (spray paint - P/N 1-850337 - .6 oz liquid bottle - P/N 103-9140).
V
Q
O
Includes frame weldment plus items #7, #13, #14, #19, #21, #25, #37, #38, and Decals.
Include zerk, item #30.
Includes (2) nyloc nuts, item #38.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2 FRONT FRAME GROUP
16
Download from Www.Somanuals.com. All Manuals Search And Download.
5.3 GEARBOX COMPONENTS FOR 103-3460 & 103-3387
Item Part No.
Description
Qty.
Item Part No.
109-0198
8VR 109-0199
Description
Qty.
1
109-0188
109-0189
Asm, Input Pinion 42”.............................1
Asm, Input Pinion 48”.............................1
Center Housing W/Plugs........................1
End Housing W/Plugs & Race ...............2
Output Shaft, Gear & Brgs (42” LH) ......1
Output Shaft, Gear & Brgs (48” LH) ......1
Output Shaft, Gear & Brgs (42” RH)......1
Output Shaft, Gear & Brgs (48” RH)......1
Output Cap W/Race...............................2
Asm, Connector Tube 42” Short.............1
Asm, Connector Tube 48” Short ............ 1
Asm, Connector Tube 42” Long............. 1
Asm, Connector Tube 48” Long............. 1
Kit, Output Seal ..................................... 2
Seal, Input ............................................. 1
O-ring .................................................... 7
Washer, Cupped.................................... 1
V-ring..................................................... 1
Screw, HH 3/8-24 x 1 1/4 Gr8................ 28
V
2V 109-0190
3V 109-0191
4O 109-0192
109-0200
109-0201
V
9
10ꢀ 109-0202
11 109-0203
12 109-0204
13ꢀ 109-0205
14 93-3987
109-0193
5O 109-0194
109-0195
O
O
6R 109-0196
7VR 109-0197
Exmark red touch up paint (spray paint - P/N 1-850337 - .6 oz liquid bottle - P/N 103-9140).
V
O
ꢀ
S
Includes o-rings, item #11
Includes (1) output seal assembly, item #9
Apply bead of Mobil HTS grease (P/N 103-5217 1.5 oz packet) between seal, item #10 and v-ring, item #13.
Does not include screw, item #14.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
6.
2-Year Limited Warranty
Exmark Turf Equipment
(For units purchased on or after October 1, 2004)
Conditions and Products Covered
Owner’s Responsibilities
Exmark Mfg. Co. Inc. and its affiliate, Exmark Warranty
Company, pursuant to an agreement between them, jointly
warrant on the terms and conditions herein, that we will repair,
replace or adjust any part manufactured by Exmark and found
by us (in the exercise of our reasonable discretion) to be
defective in factory materials or workmanship for a period of
two years.
The Exmark turf equipment, including any defective part,
must be returned to an authorized Exmark service dealer
within the warranty period. This warranty extends only to
turf equipment operated under normal conditions. You
must properly service and maintain your Exmark product
as described in the operator’s manual. Such routine
maintenance, whether performed by a dealer or by you, is
at your expense.
This warranty applies to Exmark turf equipment purchased on
or after October 1, 2004 sold in the US or Canada. This
warranty may only be assigned or transferred to a second (or
third) owner by an authorized Exmark dealer. The warranty
period commences upon the date of the original retail
purchase.
As a condition to this warranty, customer shall have read
the operator's manual and shall have completed and
submitted to Exmark Warranty Company, within the
prescribed time, the Exmark warranty registration.
General Conditions
Products
Warranty Period
2 years
The sole liability of Exmark and Exmark Warranty Company
with respect to this warranty shall be repair and replacement
as set forth herein. Neither Exmark nor Exmark Warranty
Company shall have any liability for any other cost, loss
or damage, including but not limited to, any incidental
or consequential loss or damage.
• All Products (except as noted below)
• All Attachments and Accessories
• Metro 21 Series
1 year
1 year
• Belts and Tires
90 days
• Battery
• Engine*
1 Year Prorated
In particular, we shall have no liability or responsibility for:
Warranty is covered by engine manufacturer
•
•
Expenses related to gasoline, oil or lubricants.
Travel time, overtime, after hours time or other
extraordinary repair charges or charge relating to
repairs or replacements outside of normal business
hours at the place of business of the authorized
Exmark service dealer.
*Please refer to the engine manufacturer’s warranty statement
that is included in the literature packet. We are not authorized
to handle warranty adjustments on engines.
This warranty only includes the cost of parts and labor.
•
Rental of like or similar replacement equipment
during the period of any warranty, repair or
replacement work.
Any telephone or telegram charges or travel charges.
Loss or damage to person or property other than that
covered by the terms of this warranty.
Any claims for lost revenue, lost profit or additional
cost as a result of a claim of breach of warranty.
Attorney's fees.
Items and Conditions Not Covered
This warranty does not cover the following:
•
•
•
•
Pickup and delivery charges to and from any authorized
Exmark Service Dealer.
Any damage or deterioration due to normal use, wear
and tear, or exposure.
Cost of regular maintenance service or parts, such as
filters, fuel, lubricants, tune-up parts, and adjustments.
Any product or part which has been altered or misused
or required replacement or repair due to normal wear,
accidents, or lack of proper maintenance.
Any repairs necessary due to use of parts, accessories
or supplies, including gasoline, oil or lubricants,
incompatible with the turf equipment or other than as
recommended in the operator's manual or other
operational instructions provided by Exmark.
•
•
•
•
No Claim of breach of warranty shall be cause for
cancellation or rescission of the contract of sale of any
Exmark mower.
•
There are no understandings, agreements, representations,
or warranties, express or implied, including but not limited to
any regarding the merchantability (that product is fit for
ordinary use) or fitness for use (that product is fit for a
particular purpose), not specified herein, respecting the
equipment which is the subject of this warranty.
All warranty work must be performed by an authorized Exmark
Service Dealer using Exmark approved replacement parts.
Instructions for Obtaining Warranty Service
1. Contact any Exmark Service Dealer to arrange service at
their dealership. To locate a dealer convenient to you,
may also call 402-223-6375.
Some states do not allow exclusions of incidental or
consequential damages, or limitations on how long an
implied warranty lasts, so the above exclusions and
limitations may not apply to you.
2. Bring the product and your proof of purchase (sales
receipt) to the Exmark Service Dealer.
This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
If for any reason you are dissatisfied with the Service Dealer’s
analysis or with the assistance provided, contact us at:
Exmark Customer Service Department
The Exmark Warranty Company
2101 Ashland Avenue
Beatrice, NE 68310
402-223-6375 or
- 18 -
Download from Www.Somanuals.com. All Manuals Search And Download.
SEE EXMARK’S COMPLETE
LINE OF ACCESSORIES
RIDING ACCESSORIES
CUSTOM RIDE SEAT SUSPENSION SYSTEM
DECK LIFT ASSIST KIT
HITCH KIT
LIGHT KIT
MICRO-MULCH SYSTEM
ROLL OVER PROTECTION SYSTEM (ROPS)
SNOW BLADE
SUN SHADE
TRASH CONTAINER
TURF STRIPER
ULTRA VAC COLLECTION SYSTEM
ULTRA VAC QUICK DISPOSAL SYSTEM
WALK BEHIND ACCESSORIES
GRASS CATCHER
MICRO-MULCH SYSTEM
STEERABLE SULKY
SULKY HITCH KIT
TURF STRIPER
E-Z RIDER
Check us out on the Web:
© 2005 EXMARK MFG. CO. INC.
INDUSTRIAL PARK BOX 808
BEATRICE, NE 68310
PART NO. 103-8614 Rev A.
(402) 223-6300
FAX (402) 223-5489
®
ALL RIGHTS RESERVED
PRINTED IN U.S.A.
MFG. CO. INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
|